Dimplex Plx 500 Wti Users Manual EC53.. Series Instructioons

PLX 500, WTI 500 to the manual 49c275d2-3d70-4997-8e93-6140adc9a9ab

: Dimplex Dimplex-Plx-500-Wti-500-Users-Manual-425886 dimplex-plx-500-wti-500-users-manual-425886 dimplex pdf

Open the PDF directly: View PDF .
Page Count: 4

Installation and Operating Instructions

INDPUKP5RG Issue 0

PLX Panel Convector Heaters

Dimensions

(millimetres)

Model(s)Watt A B

PLX 500/NC/TI/WTI 500 450 108

PLX 625/NC 625 688 108

PLX 750/NC/TI 750 620 108

PLX 1000/NC/TI/WTI 1000 620 108

PLX 1250/NC/TI 1250 688 108

PLX 1500/NC/TI/WTI 1500 688 108

PLX 2000/NC/TI/WTI/TX 2000 860 108

PLX 3000/TI/TX 3000 860 143

Important Safety Advice

When using electrical appliances, basic precautions

should always be followed to reduce the risk of fire,

electrical shock, and injury to persons, including the

following:

IMPORTANT – The wall brackets supplied with the

appliance must be used.

IMPORTANT – If the heater is installed in a room

containing a bath or shower, it must be so installed that

switches and other controls cannot be touched by a

person using a bath or shower.

Do not use outdoors.

Do not locate the heater immediately below a fixed socket

outlet or connection box.

Do not cover the heater. Do not place material or

garments on the heater, or obstruct the air circulation

around the heater, for instance by curtains or pushing

furniture up against the heater, as this could cause

overheating and a fire risk.

NEVER cover or obstruct in any way the heat outlet slots

at the top of the heater or the air inlet slots in the base of

the heater.

The heater carries the Warning symbol indicating

that it must not be covered.

WARNING – THE SURFACES OF THIS HEATER CAN BE

HOT. Momentary contact with any part of the heater

should not cause injury. However, aged or infirm persons

or young children should not be left unsupervised in the

vicinity of the heater unless a suitable guard is fitted.

This appliance is not intended for use by children or

other persons without assistance or supervision if their

physical, sensory or mental capabilities prevent them

from using it safely. Children should be supervised to

ensure that they do not play with the appliance.

Note that due care and consideration must be taken

when using this heater in series with a thermal control,

a program controller, a timer or any other device that

switches on the heat automatically, since a fire risk

exists when the heater is accidentally covered or

displaced.

If the supply cord is damaged it must be replaced by the

manufacturer or service agent or a similarly qualified

person in order to avoid a hazard.

Fig. 1

IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE

A

150

MIN

‘x’ 150

MIN

150

MIN

B

430

Electrical

WARNING – THIS APPLIANCE MUST BE EARTHED

The electrical installation must be carried out by a competent

electrician, and be in strict accordance with the current I.E.E.

regulations for Electrical Equipment in Buildings.

The heater is fitted with a length of flexible cable type H05VV-

F size 3 x 1.0mm2 on models PLX 500 - 2000 and size 3 x

1.5mm2 on PLX 3000 models, for connection to the fixed

wiring of the premises through a suitable connection box

positioned adjacent to the heater.

The supply circuit to the heater must incorporate a double

pole isolating switch having a contact separation of at least

3mm.

Supplementary Earth Bonding

Should Equipotential Earth Bonding be required the earthing

conductor in the supply cord is deemed to provide the

supplementary bonding connection (see Regulation 547-

03-05, 16th Edition I.E.E. Wiring Regulations).

General

The PLX Convector is designed for wall mounting on the wall

brackets supplied. It should only be operated when in the

upright position as shown.

All models are splashproof to IP24 standard.

Models PLX…TI are fitted with a 24 hour programmable

timer.

Models PLX…TX are fitted with a 7 Day programmable timer.

Models PLX…NC are fitted with no controls, for use with

external thermostatic or programming controllers.

Before connecting the heater check that the supply voltage is

the same as that stated on the heater.

Fig. 3

Fig. 4

Wall Mounting

IMPORTANT – The wall brackets supplied with the appliance

must be used. The heater should be positioned observing

the minimum clearances stated around the heater - see

Fig. 1.

DO NOT locate the heater immediately below a fixed socket

outlet or connection box.

1. Remove wall mounting bracket from the back of the

heater by depressing the spring latch at the top of

each bracket - see Fig. 2.

2. Fix the wall bracket securely to the wall through the

four screw holes provided.

3. Present the heater to the wall bracket, and engage

lower slots in the back with bracket.

4. Raise the heater to upright position and push the

heater onto brackets to engage top latch.

Access to the controls

The controls cover (see ‘x’ in Fig. 1) on your heater has a

latch which may be locked shut if desired using a small

bladed screwdriver - see Fig. 3.

To open the cover insert the blade of the screwdriver in the

small slot and rotate a quarter of a turn clockwise to

disengage the latch. The cover may then be hinged back

towards the wall for access to the controls.

Operation - Thermostat only models

Control of Output and Temperature (see Fig. 4)

The switch marked O and I controls the electricity supply to

the heating elements. The OFF position is marked O.

The switch marked I - II (half heat – full heat) provides a

choice of output as desired.

Fig. 2

255

MIN

Thermostat Operation

The heater is fitted with an adjustable thermostat enabling

the room temperature to be controlled by adjusting the setting

accordingly. The * setting represents a room temperature of

approximately 5°C and may be used for protection against

frost. Higher temperature settings range from 1-6 (max.)

creating a room temperature of approximately 30°C.

A neon indicator light glows when the appliance is actually

heating.

Switch on the heater and turn the thermostat knob to mark 6

opposite the indicator mark (located on centre right of the

knob - see Fig. 4 & 5), and set selector switch to full heat

output to warm the room rapidly. When the room temperature

has reached the desired level, turn the thermostat knob back

slowly until the thermostat just clicks off. The heater will then

maintain the room temperature at the chosen level, provided

that the correct size of heater has been selected for the room

to be heated.

NOTE – Should your heater fail to come on when the

thermostat knob is at a low setting, this may be due to the

room temperature being higher than the thermostat setting.

Operation - TI and TX Timer Models

Control of Output and Temperature (see Fig. 5)

The slide switch on the timer unit controls the electricity

supply to the heating elements on TI and TX models.

The switch marked I - II (half heat – full heat) provides a

choice of output as desired.

Thermostat Operation

- see above.

Using the Timer

The heater must be connected to the electricity supply for the

timer to operate. Set the timer by rotating the dial clockwise

until the correct time of day is indicated opposite the datum

mark (located at centre front of the timer - see Fig. 5).

‘OFF’ Position

Set the timer switch to position. The timer operates but the

heater will not output any heat, as the electricity supply to the

heating elements has been disconnected.

Manual Operation

Set the timer switch to position. The heater will now operate

continuously under the control of the thermostat - see

‘Thermostat Operation’ above.

Fig. 5

11

13

12

14

Automatic Operation

Set the timer switch to position. The panel will now operate

during set ‘ON’ periods under the control of the thermostat.

To set the timer’s ‘ON’ and ‘OFF’ periods:

1. Using your finger tip or the tip of

a pencil, push in as many segments

as necessary around the dial,

according to the times you don’t

require heat – see Fig. 6. Each

segment pushed in switches the

heater OFF for that part of the hour.

All other segments will be ‘ON’.

2. You can select as many ‘ON’ periods as you like, within

the 24-hour day. The settings will repeat every day until

changed.

3. To change ‘ON’ and ‘OFF’ times, simply push in any ‘ON’

segments you wish to cancel and pull out new ‘ON’

segments as required.

Note: On TI models each segment on the timer represents

20 mins.

TX Models

TX Models are fitted with 7 day programmable timers. In all

other respects they are identical in installation and operation

to 24 hour timer operation on TI models.

1. Setting the Time

The current day and time is set by rotating the timer dial

clockwise until the correct day and time is indicated opposite

the datum mark.

2. Automatic Operation

Set the time switch to the symbol. Select the days and

times you require the heater to come on by pulling out the

appropriate segments. Each segment represents a 13/4 hour

period for the day indicated. The timer may be set to give as

many ‘ON’ periods of any length required in multiples of 13/4

hours. The programme will repeat itself every 7 days until

changed.

The programme may be over-ridden at any time by switching

to or and can be reinstated by switching back to

setting.

Fig. 6

Safety - Overheat protection

For your safety this appliance is fitted with a thermal cut-out.

In the event that the product overheats for some reason, the

cut-out prevents excessive temperatures on the product by

cutting the power to the heater. Once the heater has cooled

down, it will reset automatically, it will continue to cycle on

and off automatically until the reason for overheating is

removed.

Cleaning

Before commencing cleaning, unplug the heater and allow it

to cool. Disconnect the electricity supply to the appliance.

The outside can be cleaned by wiping it over with a soft damp

cloth and then dried. Do not use abrasive cleaning powders

or furniture polish, as this can damage the surface finish.

To release heater from the wall bracket for cleaning or

redecoration, depress latch on both brackets (see Fig. 2)

and hinge forward.

After Sales Service

Your product is guaranteed for two years from the date of

purchase.

Within this period, we undertake to repair or exchange this

product free of charge provided it has been installed and

operated in accordance with these instructions.

Your rights under this guarantee are additional to your statutory

rights, which in turn are not affected by this guarantee.

Should you require after sales service you should contact

our customer services help desk on 0870 727 0101. It would

assist us if you can quote the model number, series, date of

purchase, and nature of the fault at the time of your call. The

customer services help desk will also be able to advise you

should you need to purchase any spares.

Please do not return a faulty product to us in the first instance

as this may result in loss or damage and delay in providing

you with a satisfactory service.

Please retain your receipt as proof of purchase.

Glen Dimplex UK Limited

Millbrook House

Grange Drive

Hedge End

Southampton

Hampshire. SO30 2DF

The product complies with the European Safety Standards EN60335-2-30 and the European Standard Electromagnetic Compatibility

(EMC) EN55014, EN60555-2 and EN60555-3 which cover the essential requirements of EEC Directives 73/23 and 89/336

UK customer help line (8.00AM – 6.00PM Mon-Fri; 8.30AM-1.00PM Sat)

Customer Services: Tel. 0870 7270101

Fax. 0870 7270102

e-mail customer.services@glendimplex.com

Republic of Ireland Tel. 01 8424833

[c] Glen Dimplex UK Limited

All rights reserved. Material contained in this publication may not be reproduced in whole or in part, without prior permission in writing of Glen Dimplex UK Limited.

Energy Saving Tips

The energy we use to heat, light and power our homes

contributes over a quarter of the UK’s carbon emissions, the

principle contributor to climate change.

Around half the energy used in the home is for heating and

hot water, so using your heating system efficiently will not

only help the environment, but also save you money !

Energy efficiency tips for heating and hot water

1. Don’t set the temperature too high…

By reducing the thermostat setting by just 1ºC can reduce

your energy use by as much as 10%. And if you’re going

away for the winter, leave the thermostat on the frost protection

setting to provide protection from freezing at a minimum cost.

2. Use it where you need it…

Set the appropriate temperature on your heaters for the room

they are in; for example, leave the thermostat on a heater in a

spare bedroom on a lower setting.

3. Use it when you need it…

Use heaters fitted with timers or linked to central controllers

to turn the heating on only when you need it and automatically

switch it off when you don’t.

4. Curtains…

Close your curtains at dusk to stop heat escaping through

the windows.

5. Windows…

Nearly 25% of heat loss can occur through poorly insulated

frames and single glazing. If you can’t afford to double glaze

all your windows, go for the rooms you heat most.

6. Treat your hot water tank...give it a jacket

An insulating jacket for hot water tanks only costs a few pounds

and pays for itself within months. Fit one that’s at least 75mm

(3") thick and you could save £10-£15 a year.

7. Water …

Use a shower if you have one to save time, money and water.

Don’t set the thermostat too high on your water heater - 60oC/

140oF is usually adequate for bathing and washing.

Put the plug in when running hot water in your sink - leaving

hot taps running is both wasteful and expensive.

Ensure dripping taps are repaired quickly. In just one day,

you could waste enough water to fill a bath.

Other Energy Saving Tips for Around the Home

1. Lights

Turn off lights whenever you leave a room for more than ten

minutes.

Use low-energy bulbs wherever you can as they use less

than a quarter of the electricity used by ordinary light bulbs

and last ten times longer!

2. Cooking

Use the right size pan for the food and cooker hob.

Keep saucepan lids on - this enables you to turn down the

heat.

Boil water for cooking in a kettle.