157661D 42 INCH LAWN DECK S&O !! So 100428

Preview ! 157661d_42_inch_lawn_deck_so_100428 Western Safety Products Lawn Mower Manuals - Lawn Mower Manuals – The Best Lawn Mower Manuals Collection

User Manual: !! Western Safety Products Lawn Mower Manuals - Lawn Mower Manuals – The Best Lawn Mower Manuals Collection

Open the PDF directly: View PDF .
Page Count: 24

Download
Open PDF In Browser	View PDF

®
`
DR
42" LAWN MOWER DECK

SAFETY & OPERATING INSTRUCTIONS

Serial No.
Order No.

Original Language

DR Power Equipment
Toll-free phone: 1-800-DR-OWNER (376-9637)
Fax: 1-802-877-1213
Website: www.DRpower.com

Read and understand this manual and all instructions before operating the DR 42" LAWN MOWER DECK.

Table of Contents
Chapter 1: General Safety Rules.............................................................................................................................................. 3
Chapter 2: Setting Up The DR 42" LAWN MOWER DECK .................................................................................................... 5
Chapter 3: Operating DR 42" LAWN MOWER DECK ............................................................................................................ 8
Chapter 4: Maintaining The DR 42" LAWN MOWER DECK.................................................................................................. 10
Chapter 5: Troubleshooting .................................................................................................................................................... 14
Chapter 6: Parts Lists, Schematic Diagrams And Warranty .................................................................................................. 16

Conventions used in this manual

This indicates a hazardous situation, which, if not avoided, could result in death or serious injury.

This indicates a hazardous situation, which, if not avoided, could result in minor or moderate injury.

This information is important in the proper use of your machine. Failure to follow this instruction could result in damage
to your machine or property.

Serial Number and Order Number
A Serial Number is used to identify your machine and is located on the Serial Number Label on your machine. An Order Number
is used to check and maintain your order history and is located on the upper left portion of your packing slip. For your
convenience and ready reference, enter the Serial Number and Order Number in the space provided on the front cover of this
manual.

Additional Information and Potential Changes
DR Power Equipment reserves the right to discontinue, change, and improve its products at any time without notice or obligation
to the purchaser. The descriptions and specifications contained in this manual were in effect at printing. Equipment described
within this manual may be optional. Some illustrations may not be applicable to your machine.

DR® 42" LAWN MOWER DECK

Chapter 1: General Safety Rules

•

Read this Safety & Operating Instructions Manual before you use the DR 42" LAWN MOWER DECK. Become familiar with
the operation and service recommendations to ensure the best performance from your machine.
• Before you use the DR 42" LAWN MOWER DECK refer to and follow your DR® FIELD and BRUSH MOWER Safety and
Operating Instructions Manual for Field and Brush Mower specific Warnings and Cautions.
If you have any questions or need assistance, please contact us at www.DRpower.com or call toll-free 1-800-DR-OWNER (3769637) and one of our Technical Support Representatives will be happy to help you.

Labels
Your DR 42" LAWN MOWER DECK carries prominent labels as reminders for its proper and safe use. Shown below are copies of
all the Safety and Information labels that appear on the equipment. Take a moment to study them and make a note of their
location on your LAWN MOWER DECK as you set up and before you operate the unit. Replace damaged or missing safety and
information labels immediately.

#164381

#136491

#157641

General Safety

Operating this DR 42" Lawn Mower Deck safely is necessary to prevent or minimize the risk of death or serious injury. Unsafe
operation can create a number of hazards for you. Always take the following precautions when operating this Lawn Mower Deck:
• This is a high-powered machine, with moving parts operating with high energy at high speeds. You must use proper clothing
and safety gear when operating this machine to prevent or minimize the risk of severe injury. This machine can cut and sever
parts of your body if they contact the Moving Blades.
• Thoroughly inspect the area in which you will be working and remove all foreign objects. Clear the area of objects such as
Rocks, Toys, Wire, Bones, Sticks, Glass etc., which could be picked up and thrown by the Blades which could damage the
machine and/or cause injury.
• Read this Safety & Operating Manual before you use the DR 42" Lawn Mower Deck. Become familiar with the operation and
service recommendations to ensure the best performance from your Lawn Mower Deck.
• Never allow people who are unfamiliar with these instructions to use the Mower. Allow only responsible individuals who are
familiar with these rules of safe operation to use your machine.
• Keep your hands and feet away from the Blades, Belts, Blade Pulleys, and concealed areas while the engine is running. Never
reach under the Deck or grab hold of any part of the Deck when the Engine is running.
• Never use the Mower with the Discharge Chute removed.
• Never, under any conditions, remove, bend, cut, fit, weld, or otherwise alter standard parts on the dr 42" Lawn Mower Deck.
This includes all Shields and Guards. Modifications to your machine could cause personal injuries and property damage and
will void your warranty.
• Your DR 42" Lawn Mower Deck is a powerful tool, not a plaything. Exercise extreme caution at all times. The design of this
machine is to cut grass. Do not use it for any other purpose.
• Be sure all Blade and Wheel controls are disengaged before attempting to start the Engine. Engage and disengage the Mower
Blades a few times to get used to it before mowing.
• If you have to stop to remove grass or debris from the underside of the Deck, always shut off the Engine, allow the Engine to
cool five (5) minutes and remove the Spark Plug Wire(s) before removing grass or debris.
• Know how to stop the Blades quickly; see page 8.
• Stop the Blades when crossing gravel drives, walks, or roads.
• Always operate the Mower from behind. Never pass or stand on the discharge (right) side or in front of machine when the
Engine is running.
• Do not pull the Mower backwards unless absolutely necessary. Look down and behind before, and while moving backwards.
• If the machine starts to make an unusual noise or vibration, immediately shut off the Engine and wait five (5) minutes for all
moving parts to come to a complete stop and cool. Disconnect the Spark Plug Wire(s). Vibration is generally a warning of
trouble. Inspect for clogging or damage. Clean and repair and/or replace damaged parts.
• Keep all Nuts and Bolts tight, especially the Blade attachment Bolts, and keep the equipment in good operating condition.
• The Mower blades are sharp and can cut. Wrap the blades or wear gloves, and use extra caution when servicing.
• Keep bystanders at least 100 feet away from your work area at all times. Objects can be thrown far from the Mower and at
great speeds. To be safe, do not operate the machine near small children or pets, and never allow children to operate the
Mower. Disengage the Blades and stop the Engine when another person or pet approaches.
• Refer to your DR® FIELD and BRUSH MOWER Safety and Operating Instructions Manual for Field and Brush Mower specific
Warnings and Cautions. If you have any questions or need assistance, please contact us at www.DRpower.com or call toll-free
1-800-DR-OWNER (376-9637) and one of our Technical Support Representatives will be happy to help you.

A Note to All Users
No list of warnings and cautions can be all-inclusive. If situations occur that are not covered by this manual, the operator must
apply common sense and operate this DR 42" LAWN MOWER DECK in a safe manner. Contact us at www.DRpower.com or call
1-800-DR-OWNER (376-9637) for assistance.

DR® 42" LAWN MOWER DECK

Chapter 2: Setting Up The DR 42" LAWN MOWER DECK
It may be helpful to familiarize yourself with the controls and features of your DR LAWN MOWER DECK as shown in Figure 1
before beginning these procedures. If you have any questions at all, please feel free to contact us at www.DRpower.com.

DR LAWN MOWER DECK Controls and Features

Main Belt
Cover

Belt Tension
Release Lever

Deck Belt/Pulley
Cover (Right)
Deck Belt/Pulley
Cover (Left)

Cutting
Height
Adjuster

Rear
Castor Wheel

Deflector

Main Belt
Cover Knob

Front Castor
Wheels

Figure 1

Assembling the Lawn Mower Deck
Tools Needed:

• Pliers
• Hammer
Mounting the Front Caster Wheels
NOTE: The Caster Wheels mount on the Front Arms of the Deck Frame (Figure 2).
Front
Arms

1. Insert two black Castor Wheel Spindle Bushings (one on top and one on the
bottom) into a Front Arm of the Lawn Deck Frame. You may need to tap the
Bushings in with a Hammer (Figure 3).
2. Insert the Caster Wheel Spindle into the Bushings from the bottom(Figure
4). Push the Cotter Pin into the Hole in the Spindle as far as it will go.

Figure 2

3. Hold the Tire with one hand to keep the Axle from turning while bending the
legs of the Cotter Pin with Pliers. Bend the long leg first, then the shorter
leg.
4. Repeat steps 1-3 for assembly of the remaining Caster Wheel.

If you remove the Cotter Pins, replace them with new ones 1/4" in diameter
and 1-1/2" long. Repeated straightening and bending will break the Cotter
Pins at the bend, and may cause the Caster Wheels to come off during
operation causing severe damage or possible injury.

Bushings, top
and bottom
Figure 3
Cotter Pin
Caster Wheel
Spindle

Installing the Discharge Chute
NOTE: If your new Lawn Mower Deck shipped separately from your DR FIELD and
BRUSH MOWER, you will need to install the Discharge Chute.
Tool Needed:

• 1/2" Wrench
1. From below, insert the two Carriage Bolts up through the holes in the Deck.
(Figure 5).
2. Set the Discharge Chute in place by fitting the Bracket over the Bolts and
install the two 5/16" Locknuts. Tighten the Nuts using a 1/2" Wrench.
Figure 4

Removing the Existing Attachment
Refer to your DR® Field and Brush Mower Safety and Operating Instructions
Manual for removing the Brush Deck or refer to the Attachment Users Manual
for removal of other Attachments.

Installing the Lawn Mower Deck

Locknut
Carriage
Bolts Under
Deck
Figure 5
6

Discharge
Chute

DR® 42" LAWN MOWER DECK

Wait five minutes for your DR Field and Brush Mower to cool down if it was
being used. Remove the Key and disconnect the Spark Plug Wire before
installing the Mower Deck.

NOTE: Your Lawn Deck shipped with the Belt in place on the two Blade Drive
Pulleys. Occasionally, the Belt comes off during shipping. If this occurs,
remove the Left and Right Side Belt Covers from the Deck (Figures 6) with
a 1/2" Wrench and place the Belt back on the Pulleys.

Main Belt
Cover
Right Side
Belt Cover

Right Side
Belt Cover

1. Remove the Front Knob and the Main Belt Cover (Figures 6).
2. With the help of another person to steady the DR Field and Brush Mower
Power Unit, line up the Lawn Mower Deck with the Power Unit Attachment
Pin and slide the Lawn Mower Deck onto the Pin.
3. Attach the Collar and insert the Retaining Pin (Figure 7).

Knob
Figure 6

4. Mount the Belt on the Field and Brush Mower Engine Pulley. Ensure that the
Belt is routed correctly around the other Pulleys (Figure 8).
5. Push the Belt Tension Release Lever towards the center of the Deck and set
the outside of the Belt against the flat Idler Pulley that is on the Release
Lever.

Retaining
Pin
Collar

Tip: Some people push the Lever with their foot.
6. Replace the Main and Side Belt Covers if you removed them.
NOTE: Be certain to replace the Side Belt Cover Hardware in the position and order
that you removed it (see “Schematic – Deck Assembly” in Chapter 6 for
reference when re-installing the covers).

Check the Tire Pressure

Figure 7

Tools Needed:

• Tire Pressure Gauge
• Air Compressor

Engine Pulley
Deck

1. Remove the Valve Stem Protective Cap and check the tire pressure with a
Tire Pressure Gauge.

Apply
Tension

2. Refer to the manufacturers recommended pressure is that is stamped on the
side of the Tire.

Belt
Tension
Lever

3. If the pressure is too low, add air through the Valve Stem with an air hose.
BELT PATH

4. Replace the Valve Stem Protective Cap when finished.

Do not over inflate the tires. Inflate to the manufacturers recommended
pressure found on the tires.

Release
Tension

Figure 8

Chapter 3: Operating DR 42" LAWN MOWER DECK
For more specific information on the proper operation of the Field and Brush Mower, Refer to your DR Field and Brush Mower
Safety and Operating Instructions Manual.

Engaging the Lawn Deck Blades
5. Hold down the Operator Presence Lever (Figure 1) of your DR Field and Brush Mower.
6. Engage the Blades by pulling up on the Blade Engage/Disengage Knob.
NOTE: If you pull up on the Blade Engage/Disengage Knob before holding down the Operator Presence Lever, the engine will shut off.

Always disengage the blades of the DR 42" Lawn Mower Deck before shifting into reverse.

Stopping the Lawn Deck Blades
1. Disengage the Blades by pushing down on the Blade Engage/Disengage
Knob.
NOTE: Releasing the Operator Presence Lever will cause the engine to shut off but
always remember to push down on the Blade Engage/Disengage Knob before trying
to start the Engine again.

Always disengage the Blades of the DR 42 " Lawn Mower Deck before
adjusting the cutting height.

Clevis
Pin

Adjusting the Cutting Height

Cutting Height
Adjustment Lever
Figure 9

1. To change height settings, remove the Clevis Pin and re-position the Cutting
Height Adjustment Lever. After adjusting to a new height, re-insert the
Clevis (Figure 9).
NOTE: You can adjust the cutting height of the Mower Deck in 1/2" increments.
The Clevis Pin prevents accidental dislodging of the Cutting Height Adjustment Lever
over rough terrain.

Obstacle Tips

The mower engine's power can easily throw stones, sticks, and other debris at great velocity, which could cause personal injury or
property damage. Never run the machine over gravel driveways or over loose stones or mulch with the mower deck blades
spinning.

• Always check your work area before mowing and remove any debris that might tangle or damage the machine.
• If you do run into debris and the Mower Deck becomes tangled, turn off the engine and disconnect the spark plug wire(s)
before attempting to untangle the machine.

DR® 42" LAWN MOWER DECK

Slopes

When operating the DR 42" Lawn Mower Deck over uneven terrain or slopes, use extreme caution not to tip over the machine.

• Do not use the DR 42" Lawn Mower Deck on slopes greater than 20 degrees. Doing so could result in serious injury or
damage to your machine.

• If you have to mow on sloping terrain, mow across the slope, not up and down, for better control.
Tip: Locking the Differential in will improve traction, and keep the machine traveling on a straighter path. Once on level terrain,
Lock out the differential for easier turning.

• To avoid “free-wheeling”, shift into a lower gear before going down a slope. Do not shift while on a slope. Be ready to use the
brake, if necessary.

• The Mowing Deck pivots from side to side, which helps avoid scalping, and keeps the weight balanced over the drive wheels
when operating on uneven terrain.

If The Machine Becomes Obstructed
1. Disengage the Lawn Deck Blades. Do not try to free the machine from debris with the Blades engaged.
2. Try putting the machine in reverse and backing away from the obstacle.
3. Try pushing down on the Handlebars to lift the Mowing Deck over the obstacle.

•
•

If you need to leave the operating position to clear debris from the Deck, first put the machine in "n" (neutral), turn the
Engine off, set the Brake, and disconnect the Spark Plug wire(s).
Do not touch the exhaust areas when reaching for the Spark Plug(s), they are very hot.

Turns
•

Use a low gear when turning. This will give you better control and a cleaner cut.

Reverse
• Be very careful of your footing when operating the machine in Reverse. Know what is behind you and take your time.
• Disengage the Lawn Deck Blades before shifting into Reverse. Mow in the Forward gears only, using Reverse for maneuvering.
• If you find it difficult to shift into Reverse, lightly "feather" the Clutch Lever as you put the Shift Lever into Reverse, then quickly
release the Clutch Lever.

Cutting in Wet and Heavy Grass
• Be very careful of your footing when mowing in wet conditions. Avoid steep slopes and other slippery areas.
• To achieve the best cut, mow when the grass is dry. If you have to mow when the grass is wet, use a lower, slower speed.
• We do not recommend using the optional Mulching Plate in wet and heavy grass.

Chapter 4: Maintaining The DR 42" LAWN MOWER DECK
Regular maintenance is the way to ensure the best performance and long life of your machine. Please refer to this Chapter for
maintenance procedures. The service intervals shown are maximum under normal operating conditions. Increase frequencies
under extremely dirty or dusty conditions.

Regular Maintenance Checklist
PROCEDURE

BEFORE EACH USE

EVERY 25 HOURS

S
S

Check General Equipment Condition
Check Blades for Sharpness
Check Tire Pressure
Check Deck Belt Tension and Condition
Lubricate Caster Wheels and Spindles

S
S
S

Lubrication
Wheel Caster
Spindle

Grease
Fitting

Tools and Supplies Needed:
• Flexible Hose Grease Gun
• Lithium Grease

Before performing any maintenance procedure or inspection, stop the engine
of the Field and Brush Mower, wait five (5) minutes to allow all parts to cool.
Disconnect the spark plug wire, keeping it away from the spark plug.
NOTE: When using the Grease Gun, pump only until you feel slight resistance (1-2
pumps should do it).
1. Grease the fittings on the front Caster Wheels (Figure 10).
2. Grease the fittings on the Lawn Deck Frame where the Wheel Castor
Spindles swivel
NOTE: Perform this lubrication more often in dry and dusty environments.
Grease
Fitting

Removing and Replacing the Deck Belt
Tools Needed:
• 7/16" Wrench and/or Socket
• 1/2" Wrench
• 3/16" Allen Wrench

Figure 10

DR® 42" LAWN MOWER DECK

Main Belt
Cover

Use only a DR Belt on your machine. The Belt has been thoroughly tested and
proven for many hours of use.

Right Side
Belt Cover

1. Remove the Main Belt Cover and the two Side Belt Covers (Figure 11).
2. Push and hold the Belt Tension Release Lever towards the center of the
machine. (Figure 12).
3. Remove the Belt from the Deck Pulleys and the Engine Pulley.
4. Remove the lower Bolt on the Rear Link Plates (Figure 13) and swing the Link
Plates out of the way so the Belt clears. Remove the Belt.

Knob
Figure 11
Engine Pulley
Deck

Release
Tension

5. To mount the new Belt, reverse the above procedure. The correct Belt travel
on the Pulleys is shown below.

Apply
Tension

NOTE: Be certain to replace the Side Belt Cover Hardware in the position and order
that you removed it (see “Schematic – Deck Assembly” in Chapter 6 for
reference when re-installing the covers).

Belt
Tension
Lever
BELT PATH

Removing and Replacing the Blades
•

•

Before performing any maintenance procedure or inspection, stop the
engine of the Field and Brush Mower, wait five (5) minutes to allow all
parts to cool. Disconnect the spark plug wire, keeping it away from the
spark plug.
Use caution when pushing or pulling the Wrench next to the Blade. Wear
Gloves; if the Wrench slips off the Bolt, you may be seriously injured.

Figure 12
Lower Bolt on
Rear Link Plates

Tools and Supplies needed:

•
•
•
•

9/16" Wrench or Socket
Torque Wrench (optional)
Protective Gloves
Board to brace the Blade

1. Remove the Deck from the Field and Brush Mower and secure the Deck so
you can access the Blades.

Figure 13
Blade

2. Block the Blade with a piece of wood between the Blade and the Mower
Deck. (Figure 14)
NOTE: Observe the orientation of the Blade before removing in the next step.
3. Loosen the Bolt and remove the Blade Bolt, Lock Washer, and Blade Washer
by turning counter clockwise (right hand, regular thread).
4. Remove the Blade.
5. Repeat Steps 2 thru 4 for the other Blade.

Loosen

Figure 14

Wood Piece Inserted
to Block the Blade

Flange towards
Ground

6. Mount the new Blade (with the center flange towards the ground), Blade
Washer, Lock Washer, and Blade Bolt, in that order (Figure 15).
7. Block the blade with the wood piece and tighten securely (Torque 30-40 ftlbs.).
NOTE: Be sure that you have the Blade seated completely over the small ridge in
the spindle hub before tightening the Bolt.
8. Repeat Step 6 for the other Blade.

Leveling the Lawn Mower Deck

Tighten
Wood Piece Inserted
to Block the Blade

The DR 42" LAWN MOWER DECK settings made at the factory are suitable for
most purposes, however, leveling adjustments from side to side and front to
rear can be made if desired by following the instructions below.

Blade

Figure 15
Main Belt
Cover

NOTE: All references to left and right are from the Operator's position.
Tools needed:

• 1/2" Wrench
• 3/16" Allen Wrench
Knob
Figure 16

1. Move the machine to a level area.
2. Unscrew the Knob and remove the Main Belt Cover (Figure 16) and locate
the Adjustment Brackets (Figure 17).

Rear Adjustment
Bracket (front to
rear adjustments)

Leveling the Deck Front to Rear

Front Adjustment
Brackets (side to
side adjustments)

NOTE: Adjusting the Deck so the rear is 1/4" higher than the front will provide the
best cut.
1. Measure the distance from the ground to the bottom of the Deck Edge
Flange at the front and rear of the Deck (Figure 18).
2. Using a 3/16" Allen Wrench and a 1/2" Wrench, adjust the Deck from front
to rear as needed by moving the top and/or the bottom Bolt to a different
hole in the Rear Adjustment Bracket (Figure 19).

Figure 17
Mower
Deck

Measure
Here

Rear
Adjustment
Brackets

Blade

1/4"
Adjustment
Deck

Figure 18
12

1/16"
Adjustment

DR® 42" LAWN MOWER DECK

Figure 19

3. You can make further adjustments front to back by adjusting the Front
Brackets (Figure 20). Each adjacent hole will alter the deck height by 1/4"
front to back if you move both Front Brackets at the same.

Front
Adjustment
Brackets

Leveling the Deck Side to Side
4. Measure the distance from the ground to the bottom of the Deck Edge
Flange on the left and right sides of the Deck (Figure 18, on previous page).
5. Using a 3/16" Allen Wrench, adjust the Deck on each side as needed by
moving the Mounting Bolt to a different hole in the Front Bracket. Each
Hole in the Front Bracket will change the Deck height on that side by 1/4".

1/4"
Adjustment

Deck
Figure 20

Chapter 5: Troubleshooting
Most problems are easy to fix. Consult the Troubleshooting Table below for common problems and their solutions. If you
continue to experience problems, contact us at www.DRpower.com or call toll-free 1-800-DR-OWNER (376-9637) for support.

Troubleshooting Table

SYMPTOM

POSSIBLE CAUSE

The Deck lacks power.

⇒ Check the Belt for wear.
⇒ Check the Blades Drive Pulleys for looseness. If you find a loose Pulley, remove the Pulley and
inspect the Pulley Hub and Blade Spindle, and replace if worn, or damaged. The design of the
Pulleys is to shear with severe loads or impact.

Excessive vibrations.

⇒ Check the Blades for nicks and wear. Replace or sharpen and balance the Blades if they
become dull, or have them professionally sharpened if needed. Never try to straighten a bent
Blade. Be sure to replace the Blades in the proper orientation. See page 11
⇒ The Blades may not be seated properly on the Hubs. Loosen the Blade Bolts, reset the
Blades, and tighten the Bolts. See page 11.
⇒ The Blade Spindle Bearings may be bad. Call 1 (800) DR-OWNER (376-9637) for assistance.
⇒ Check and retighten all of the fasteners as required.

The Belt frays or rolls
over the Pulleys.

⇒
⇒
⇒
⇒

The cut material is not
properly discharging out
of the right side of the
Deck.

⇒ The Discharge may be blocked. Disengage the Blades, turn off the engine, set the parking
brake, disconnect the spark plug wire(s), and then check for debris.

The Blades do not cut or
are loose.

⇒ The Blades may not be seated properly on the Hubs. Loosen the Blade Bolts, reset the
Blades, and tighten the Bolts. See page 11.

A Pulley groove may have a nick in it. File off any nicks on the Pulleys.
Check the Belt for wear and hard spots.
The Belt may be stretched; replace it.
Check Flat Idler and Tensioning Pulley for alignment and wear; replace as needed.

DR® 42" LAWN MOWER DECK

Chapter 6: Parts Lists, Schematic Diagrams And Warranty

Parts List - Deck Frame Assembly
NOTE: Part numbers listed are available through DR Power Equipment.
Ref# Part#

Description

01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21

Frame
Plate, Height Adjustment
Lever, Height Adjuster
Bushing, .766" ID x 1.0" OD
Bushing, 1.38" ID x 1.63" OD x 1.5" L
Wheel, Caster, 11.4" x 4", Gray
Knob, Handlebar, 5/16"-18
Grease Fitting, 1/4"-28, Straight
Pin, Roll, 3/16" x 1"
Pin, Cotter, 3/16" x 1-1/2"
Yoke, Caster Axle
Cover, Guard, Main Belt, Center
Pin, Cotter, 1/4" x 1-1/2"
Nut, Nylon Lock, 3/8"-16, Low Profile
Nut, Nylon Lock, 1/4"-20
Screw, 3/8"-16 x 1-1/2"
Plate, Anti-Torsion
Bushing, .265" ID x .370" OD
Bolt, 1/4"-20 x 1-1/4", HCS
Washer, Flat, 1/4", USS
Pin, Clevis

151501
157141
151561
123761
150721
193131
143661
101891
110961
126851
151511
160851
160911
164131
110731
145221
151641
157221
114681
112381
192461

DR® 42" LAWN MOWER DECK

Safety and Information Labels
192391
157641

Label, DR Logo, 5.75", Silver
Label, Height Adjustment

Schematic – Deck Frame Assembly

080303

Parts List – Height Adjuster Assembly
NOTE: Part numbers listed are available through DR Power Equipment.
Ref# Part#

Description

01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17

Hanger, Lawn Deck Shaft
Bushing, .645" ID x .75" OD x1.1" L
Rod, Hanger, Front
Rod, Hanger, Rear
Plate, Link, Rear
Plate, Link, Front
Connector, Linkage
Pin, Spring, 3/16" x 1-3/4"
Screw, Shoulder, 5/16"-18
Pin, Hitch Clip
Spring, E, .750" OD x .093" Wire
Nut, Nylon, Lock, 5/16"-18
Washer, Flat, 3/8", SAE
Bolt, 3/8"-16 x 2-1/4", HCS
Nut, Nylon Lock, 3/8"-16, Low Profile
Nut, Nylon Lock, 3/8"-16
Screw, 3/8"-16 x 1-1/2"

151551
151491
151541
151531
157191
151631
151591
110971
151601
151921
157231
110761
121701
157121
164131
110751
145221

DR® 42" LAWN MOWER DECK

Schematic – Height Adjuster Assembly

080303

Parts List – Deck Assembly
NOTE: Part numbers listed are available through DR Power Equipment.
Ref# Part#

Description

Ref# Part#

Description

01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22

Spindle Assembly w/Hardware
Lawn Deck w/Plate
Lever, Idler Arm
Pulley, Flat, Idler, 4"
Guard, Left Belt Cover
Guard, Right Belt Cover
Bolt, Shoulder, 3/8"-16 x 2-1/2", HCS
Pulley, V Belt, 6"
Nut, Hex Lock, 9/16"-18
Spacer, .675" ID x 1.125" OD
Stripper
Blade, 21", Mulching
Washer, .385" ID x 1.390" OD
Spacer, .39" ID x 1" OD x .785"L
Bolt, 3/8"-16 x 2-3/4", HCS
Deflector
Pin, Hinge, .312" x 6.75"
Spring, Deflector
Bracket, Deflector
Baffle, Vortex
Bracket, Anti-Scalping, RH Wheel
Bracket, Anti-Scalping, LH Wheel

23
157211
24
157131
25
157321
26
157081
27
157311
28
150941
29
165131
30
157301
31
145291
32
110731
33
110761
34
121701
35
112391
36
165151
37
151731
38
110751
39
112371
40
112481
Not Illustrated

Bushing, 3/8" ID x 5/8" OD x 1.03" L
Screw, Shoulder, 3/8"-16
Nut, Push, 5/16"
Wheel, Anti-Scalping
Screw, 5/16"-18 x 1-1/4", Tri Lobe
Spring, E, .750" OD x .112" Wire, 5.0" L
Bolt, Locking, 3/8"-24 x 1-1/4", GR 8
Bolt, 1/4"-20 x 3/4", HCS
Bolt, Carriage, 5/16"-18 x 3/4"
Nut, Nylon Lock, 1/4"-20
Nut, Nylon Lock, 5/16"-18
Washer, Flat, 3/8", SAE
Washer, Flat, 3/8" USS
Washer, .385" ID x .691" OD
Belt, A100K, 1/2" x 102"
Nut, Nylon Lock, 3/8"-16
Washer, Flat, #10, USS
Washer, Lock, Ext Star, 1/4"

151701
151481
151471
151271
181601
181611
150691
151711
165121
165161
151681
151691
165141
160281
123371
151881
151901
150051
150631
151281
157111
157101

151911

Safety and Information Labels
136491
164381

DR® 42" LAWN MOWER DECK

Mulching Kit
Label, Danger
Label, Belt Guide

Schematic – Deck Assembly

100420

Notes:

DR® 42" LAWN MOWER DECK

DR® 42" LAWN MOWER DECK
2-Year Limited Warranty
Terms and Conditions
The DR® 42" LAWN MOWER DECK is warranted for two (2) years against defects in materials or workmanship when
put to ordinary and normal consumer use; ninety (90) days for any other use.
For the purposes of all the above warranties, “ordinary and normal consumer use” refers to non-commercial
residential use and does not include misuse, accidents or damage due to inadequate maintenance.
DR Power Equipment certifies that the DR® 42" LAWN MOWER DECK is fit for ordinary purposes for which a product
of this type is used. DR Power Equipment however, limits the implied warranties of merchantability and fitness in
duration to a period of two (2) years in consumer use, ninety (90) days for any other use.
The 2-Year Limited Warranty on the DR® 42" LAWN MOWER DECK starts on the date the machine ships from our
factory. The 2-Year Limited Warranty is applicable only to the original owner.
The warranty holder is responsible for the performance of the required maintenance as defined by the manufacturer's
owner's manuals. The warranty holder is responsible for replacement of normally wearing parts such as the Drive Belt
and Blades. Attachments and accessories to the machine are not covered by this warranty.
During the warranty period, the warranty holder is responsible for the machine transportation charges, if required.
During the warranty period, warranty parts will be shipped by standard method at no charge to the warranty holder.
Expedited shipping of warranty parts is the responsibility of the warranty holder.
SOME STATES DO NOT ALLOW LIMITATIONS ON THE LENGTH OF IMPLIED WARRANTIES, SO THE ABOVE
LIMITATIONS MAY NOT APPLY TO YOU.
DR Power Equipment shall not be liable under any circumstances for any incidental or consequential damages or
expenses of any kind, including, but not limited to, cost of equipment rentals, loss of profit, or cost of hiring services to
perform tasks normally performed by the DR® 42" LAWN MOWER DECK.
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU ALSO HAVE OTHER RIGHTS, WHICH VARY
FROM STATE TO STATE.

Daily Checklist for the 42 "DR LAWN MOWER DECK
To help maintain your DR Lawn Mower Deck for optimum performance, we recommend you follow this checklist each time
you use your Lawn Deck.

Before performing any maintenance procedure or inspection, stop the engine of the Field and Brush Mower, wait five (5) minutes
to allow all parts to cool. Disconnect the spark plug wire, keeping it away from the spark plug.
[ ] Check the Belt for wear, proper alignment and tension.
[ ] Check the Blades for tightness, nicks and wear. Remove any wrapped weeds and grass from the Blade Bearing Housings
to prevent buildup.
[ ] Check the general condition of the Lawn Deck, e.g.; nuts, bolts, welds, etc.
[ ] Check Tire Pressure and wear.
[ ] Check the Belt Guards for damage.

End of Season and Storage
Before performing any maintenance procedure or inspection, stop the engine of the Field and Brush Mower, wait five (5) minutes
to allow all parts to cool. Disconnect the spark plug wire, keeping it away from the spark plug.

• Remove any wrapped weeds from the blade bearing housings. Clean grass and debris from the top and underneath the
mower deck with a stiff brush.

• Check the blades for nicks and wear. Replace or sharpen and balance the blades if they become dull, or have them
•
•
•
•

professionally sharpened if needed. Never try to straighten a bent blade. Dull or bent blades can cause excessive vibration
and wear.
Clean the exterior of the unit to remove all dirt, grease, and any other foreign material. To prevent rust, touch up painted
surfaces that have been scratched or chipped.
Be sure all nuts, bolts, and screws are securely fastened.
Inspect moving parts and the Drive Belt for damage and wear; replace if necessary.
If possible, store the Lawn Deck in a dry, protected place. If it is necessary to store the Lawn Deck outside, cover it with a
protective material.

157661D

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Page Count                      : 24
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:69008db4-0bc6-4741-9b6c-7edb553567df
Producer                        : Acrobat Distiller 6.0 (Windows)
Create Date                     : 2010:04:28 11:45:13-04:00
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2010:04:28 11:45:13-04:00
Document ID                     : uuid:c5d18e5d-5177-4c2b-988b-18e15c2e294b
Format                          : application/pdf
Title                           : Microsoft Word - DRAFT 157661D 42 INCH LAWN DECK S&O.doc
Creator                         : dbashaw
Author                          : dbashaw

EXIF Metadata provided by EXIF.tools

157661D 42 INCH LAWN DECK S&O !! So 100428

Preview ! 157661d_42_inch_lawn_deck_so_100428 Western Safety Products Lawn Mower Manuals - Lawn Mower Manuals – The Best Lawn Mower Manuals Collection

Navigation menu

Versions of this User Manual:

Views

Navigation