1991_Datel_Data_Book_Vol_1_Components 1991 Datel Data Book Vol 1 Components
User Manual: 1991_Datel_Data_Book_Vol_1_Components
Open the PDF directly: View PDF .
Page Count: 298
Download | ![]() |
Open PDF In Browser | View PDF |
COMPANY HISTORY Founded in 1970, DATEL is a multinational company located approximately 35 miles south of Boston in Mansfield, Massachusetts. Our modern 180,000 square-foot facility houses our admi.nistrative offices, components and sub-systems engineering groups, modular and sUb-systems production facilities, and the most modern thinfilm and thick-film hybrid production facility in the industry. DATEL's hybrid manufacturing operation is a fully certified MIL-STD-1772 facility, supporting our high quality standards. Our worldwide sales network extends to every major data acquisition product marketplace. The people who implement this sales network are skilled professionals dedicated to providing our customers with the highest possible standards of data acquisition products available today. PRODUCT INFORMATION DATEL offers one of the industry's broadest data acquisition product lines, meeting the rapidly growing need for components and sUb-systems to interface with computers in industrial, commercial, scientific and military applications. These products employ five basic technologies: monolithic CMOS, monolithic bipolar, thin-film hybrid, thick-film hybrid and discrete component circuits. Many products employ a combination of these technologies to achieve higher levels of performance and complexity. The present product lines include: data converters, sample-hold amplifiers, analog multiplexers, amplifiers, data acquisition sub-systems, computer analog I/O boards, process monitor/controllers, digital panel meters, thermal printers, digital calibrators and power supplies. COPYRIGHT © DATEL, INC 1991 ALL RIGHTS RESERVED PRINTED IN U.S.A. PRODUCT INDEX Section 1. Sampling Analog-to-Digital Converters Section 4. Sample/Hold Amplifiers ADS-lll ...................................................................... 1-1 ADS-112 ...................................................................... 1-5 ADS-117 ...................................................................... 1-9 ADS-118 .................................................................... 1-13 ADS-120 .................................................................... 1-17 ADS-130 .................................................................... 1-19 ADS-131 .................................................................... 1-25 ADS-132 .................................................................... 1-31 ADS-193 .................................................................... 1-35 ADS-21 PC ................................................................. 1-39 ADS-924 .................................................................... 1-43 ADS-928 .................................................................... 1-47 ADS-930 .................................................................... 1-51 ADS-941 .................................................................... 1-53 ADS-942 .................................................................... 1-57 ADS-944 .................................................................... 1-61 ADS-945 .................................................................... 1-63 ADS-976 .................................................................... 1-65 SHM-20 ....................................................................... 4-1 SHM-30 ....................................................................... 4-3 SHM-40 ....................................................................... 4-5 SHM-43 ....................................................................... 4-7 SHM-45 ..................................................................... 4-11 SHM-4860 ................................................................. 4-13 SHM-6 ....................................................................... 4-15 SHM-7 ....................................................................... 4-17 SHM-91 ..................................................................... 4-19 SHM-945 ................................................................... 4-21 SHM-HU .................................................................... 4-23 SHM-49 ..................................................................... 4-25 MSH-840 ................................................................... 4-27 Section 2. Analog-to-Digital Converters ADC-207 ...................................................................... 2-1 ADC-208 ...................................................................... 2-5 ADC-228 ...................................................................... 2-9 ADC-304 .................................................................... 2-13 ADC-500/505 ............................................................. 2-17 ADC-508 .................................................................... 2-21 ADC-511 .................................................................... 2-25 ADC-520/521 ............................................................. 2-29 ADC-530 .................................................................... 2-33 ADC-908 .................................................................... 2-37 ADC-914 .................................................................... 2-41 ADC-HC12B .............................................................. 2-47 ADC-HS12B ............................................................... 2-51 ADC-HX/HZ Series .................................................... 2-55 Section 5. Hybrid Data Acquisition Systems HDAS-16/8 .................................................................. 5-1 HDAS-524/528 ............................................................ 5-7 HDAS-534/538 .......................................................... 5-11 HDAS-75/76 .............................................................. 5-15 HDAS-950/951 .......................................................... 5-19 Section 6. Analog Multiplexers MV Series ................................................................... 6-1 MX Series ................................................................... 6-5 MX-818/1616 .............................................................. 6-9 MX-826 ..................................................................... 6-13 MX-850 ..................................................................... 6-15 Section 7. Amplifiers AM-1435 ..................................................................... 7-1 AM-500 ....................................................................... 7-3 AM-551 ....................................................................... 7-5 ROJ-20,lK .................................................................. 7-7 Section 3. Digital-to-Analog Converters Section 8. Active Filters DAC-HF SERIES ......................................................... 3-1 DAC-HK SERIES ......................................................... 3-5 DAC-HP SERIES ......................................................... 3-9 DAC-HZ SERIES........................................................ 3-13 For Immediate Assistance, Dial 1-800·233·2765 FLJ-ACOl .................................................................... 8-1 FLJ-ACRl ................................................................... 8-3 FLJ-Dl, D2, DC .......................................................... 8-5 FLJ-D5, D6 .................................................................. 8-9 FLJ-R Series ............................................................. 8-11 FLJ-UR Series .......................................................... 8-13 FLJ-VL, VH, VB ......................................................... 8-17 FLT-Cl ...................................................................... 8-21 FLT-DL Series ........................................................... 8-25 FLT -U2 ...................................................................... 8-29 HOW TO USE THIS DATABOOK If you know the MODEL NUMBER, use the Product Index on the first page. If you know the PRODUCT TYPE, refer to the Subject Index on page two to determine the proper section, then refer to the SELECTION GUIDE TABLE at the beginning of that section. If you wanrPRICE and AVAILABILITY information contact your local DATEL salesperson or representative. For all OTHER INFORMATION, such as New Product Highlights, Available Literature, available High Reliability Product Programs, a listing of available DESC drawings, Substitution Guide and Ordering Guide, use the Subject Index. DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-11941TEL (508) 339-3000rrLX 174388/FAX (508) 339-6356 GENERAL INDEX Other DATEL Literature ............................................................................. Page iv New Products ............................................................................................. Page v Section 1. Sampling Analog-to-Digital Converters ................................ Page 1-1 Section 2. Analog-to-Digital Converters ................................................. Page 2-1 Section 3. Digital-to-Analog Converters ................................................. Page 3-1 Section 4. Sample/Hold Amplifiers .......................................................... Page 4-1 Section 5. Hybrid Data Acquisition Systems .......................................... Page 5-1 Section 6. Analog Multiplexers ................................................................ Page 6-1 Section 7. Amplifiers ................................................................................. Page 7-1 Section 8. Active Filters ............................................................................ Page 8-1 Other DATEL Product Lines Power Supplies .................................................................................... Page PS-1 Digital Voltage Calibrators ................................................................... Page DVC-1 Digital Panel Meters ............................................................................. Page DPM-1 Process Monitors ................................................................................. Page PM-1 Thermal Printers ................................................................................... Page TP-1 Data Conversion I/O Boards ................................................................ Page I/OB-1 Appendixes Appendix A High Reliability Programs ................................................ Page A-1 Appendix B DESC Standard Military Drawing Program ...................... Page B-1 Appendix C Older Products Still Available .......................................... Page C-1 Appendix D Substitution List ............................................................... Page D-1 Ordering Guide ........................................................................................... Back Cover For Immediate Assistance, Dial 1-800-233-2765 iii AVAILABLE LITERATURE DATEL'S ALL NEW DATA ACQUISITION HANDBOOK SERIES The following additional Handboods are presented in complete data sheet format and include Selection Guides, Application Notes, and Ordering Information. Volume 2. Data Acquisition Boards DVME, Multibus, PC Bus Volume 3. Industrial Monitor and Control Products Process Monitors, Digital Panel Meters, Thermal Panel Printers, Benchtop and Hand-held Calibrators Volume 4. Power Products DC/DC Converters, Power Supplies Also available are the following Application Notes: AN-1 High-Speed AID Converter Designs: Layout and Interfacing Pitfalls AN-2 Picking the Right Sample-and-Hold Amp for Various Data Acquisition Needs AN-3 Data Converters: Getting to Know Dynamic Specifications Data Acquisition and Conversion Handbook: A technical guide to AID - D/A converters and their applications. iv DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-11941TEL (508) 339-30001TLX 174388/FAX (508) 339-6356 NEW PRODUCTS ADS-117 Features 12-Bit, 2.0 MHz, Low-Power Sampling AID Converter • • • 2.0 MHz minimum throughput Functionally complete Small 24·pin DIP Low·power, t.4 Watts Three-state output buffers Samples to Nyquist ADS-118 Features 12-Bit, 5.0 MHz, Low-Power Sampling AID Converter • • • • ADS-941 14-Bit, 1.0 MHz, High Resolution Sampling AID Converter Features • • ADS-942 14-Bit, 2.0 MHz, High Resolution Sampling AID Converter 5.0 MHz minimum throughput Functionally complete Small 24-pin DIP Low-power, 2.3 Watts Three-state output buffers Samples to Nyquist 1.0 MHz minimum throughput Functionally complete Small 32-pin DIP Low-power, 2.8 Watts Three-state output buffers Samples up to Nyquist Features • • • • 2.0 MHz minimum throughput Functionally complete Small 32-pin DIP Low-power 2.9 Watts Three-state output buffers Samples up to Nyquist til ADS-930 Features 16-Bit, 500 KHz, High Resolution Sampling AID Converter • • • • 500 KHz sampling rate Functionally complete Small40-pin DIP Low-power, t.8 Watts Three-state output buffers Samples up to Nyquist 16-Word FIFO memory ADC-530 Features 12-Bit,Ultra-Fast, Low-Power AID Converter • • • For Immediate Assistance, Dial 1-800-233-2765 350 nSec MAX. conversion time Low-power, 2.1 Watts Small initial errors Three-state output buffers Small 32-pin DIP No missing codes v NEW PRODUCTS HDAS-950/951 Features 16-Bit, 100 KHz Data Acquisition Systems • 16-bit resolution, 100 KHz 8 SE 4 D channels Miniature 40-pin DDIP Full-scale gain range from 100 mV to 10V High-impedance output state SHM-945 Features High-Speed, Hybrid Precision Sample/Hold • • • • 500 nSec MAX acquisition time to 0.00076% Differential input 0.0004% linearity 16-bit performance over military temperature range Small 24-pin DDIP package Operates at different gain settings Features SHM-43 High-Speed, 0.01 % Hybrid Sample/Hold 35 nS MAX acquisition time to 0.01% • 1 Picosecond aperture uncertainty 75 MHz small-signal bandwidth • 520 Milliwatt maximum power dissipation • Small 14-pin DIP package • CMOS control signal MX-826 Features Precision, High-Speed Multiplexer • 225 nSec Max. settling time to 0.01 % • 400 nSec. Max. settling time to 0.003% • 150 nSec. Max. settling time to 0.1 % • 8 Channels single-ended inputs 395 Milliwatts power dissipation • Small 24-pin DDIP package MX-850 Features Precision, High Speed Multiplexer • • • 50 Nanoseconds settling time to 0.01% 70 Nanoseconds settling time to 0.003% 100 Nanoseconds settling time to 0.001 % 4 Channels, single-ended inputs 207 Milliwatts power dissipation Small 14-pin DIP package MSH-840 Features Quad Simultaneous Sample Hold • • • • • SHM-49 Features High-Speed, 0.01 % Hybrid Sample/Hold • • • vi 4 Simultaneous sample/holds Internal 4 channel multiplexer 750 nS\lc acquisition time, 10V step to 0.01% 2 channels with optional X10 gain Control logic for interfacing to AID's Low-power, 1.5 Watts 16 MHz small signal bandwidth Small 8-pin DIP or LCC package 200 nS Max. acquisition time to 0.01% 72 dB feedthrough attenuation ±25 Picoseconds aperture uncertainty 413 Milliwatts power dissipation DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194ITEL (508) 339-3000ITLX 174388/FAX (508) 339-6356 NEW PRODUCTS Features ADS-120 12-Bit, 20 MHz Sampling AID Converter 20 MHz minimum throughput Samples to Nyquist Functionally complete Small 40-pin DIP Low-power, 4.2 Watts Three-state output buffers High input bandwidth • • • 7 ADS-944 Features 14-Bit, 5.0 MHz, High Resolution Sampling AID Converter • • • ADS-945 Features 14-Bit, 10.0 MHz, High Resolution Sampling AID Converter 10 MHz sampling rate Functionally complete • Small 40-pin DIP • Low-power, 4.2 Watts Three-state output buffers • Samples up to Nyquist • 16-Word FIFO memory ADS"976 Features 16-Bit, 200 KHz, Low-Power Sampling AID Converter 5.0 MHz minimum throughput Functionally complete Small 32-pin DIP Low-power, 3.4 Watts Three-state output buffers Samples to Nyquist • • • FLT-DL 4- and 5- Pole High Frequency Digitally Programmable Active Filters For Immediate Assistance, Dial 1-800-233-2765 200 KHz sampling rate Compatible to industry standard ADC76, AD376, AD1376 Small 32-pin DIP Low-power, 1.8 Watts Samples to Nyquist 16-Word FIFO memory Features • • • • • • Digitally programmable 4- and 5-pole CAUER response Cascadable 7-pole CAUER response Cutoff frequencies to 1.2 MHz Small 32-pin DIP -55 to +125°C operation vii SAMPLING AID CONVERTERS Resolution (Bits) Throughput (MHz) Unearity Error (Max) Power Walls (Max) Case ADC-HS12B 12 0.066 ±3/4 LSB 1.8 32-Pin DIP ADS-111 12 0.500 ±3/4 LSB 1.8 24-Pin DIP 1-1 ADS-112 12 1.0 ±3/4 LSB 1.7 24-Pin DIP 1-5 ADS-193 12 1.0 ±3/4 LSB 1.7 40-Pin DIP 1-35 ADS-21PC 12 1.3 ±1 LSB 2.5 46-Pin DIP 1-39 ADS-132 12 2.0 ±3/4 LSB 3.2 32-Pin DIP 1-31 Preliminary ADS-117 12 2.0 ±3/4 LSB 1.8 24-Pin DIP 1-9 Preliminary ADS-118 12 5.0 ±1 LSB 2.5 24-Pin DIP 1-13 ADS-131 12 5.0 ±1 LSB 4.0 40-Pin DIP 1-25 ADS-130 12 10.0 ±1 LSB 4.2 40-Pin DIP 1-19 ADS-120 12 20.0 ±1 LSB 4.2 40-Pin DIP 1-17 ADS-924 14 0.300 ±1 LSB 1.8 24-Pin DIP 1-43 Model ---_. Advanced Page 2-51 -------- ADS-928 14 0.500 ±3/4 LSB 3.4 32-Pin DIP 1-47 Preliminary ADS-941 14 1.0 ±3/4 LSB 3.3 32-Pin DIP 1-53 Preliminary ADS-942 14 2.0 ±1 LSB 3.4 32-Pin DIP 1-57 Advanced ADS-944 14 5.0 ±1 LSB 3.4 40-Pin DIP 1-61 Advanced ADS-945 14 10.0 ±1 LSB 4.2 40-Pin DIP 1-63 Advanced ADS-976 16 0.200 ±2LSB 1.8 32-Pin DIP 1-65 Preliminary ADS-930 16 0.500 ±11/2 LSB 2.4 40-Pin DIP 1-51 or Immediate Assistance, Dial 1-800-233-2765 1-i Contact DATEL for your Data Acquisition component needs. Dial 1-800-233-2765 for Applications Assistance Hi DATEL. Inc. 11 Cabot Boulevard. Mansfield. MA 02048-1194fTEL (508) 339-3000fTLX 174388/FAX (508) 339-6356 ADS-iii 12-Bit, 500 KHz, Low-Power Sampling AID Converter FEATURES • • • • • • • • 12-Bit resolution Internal Sample/Hold 500 KHz minimum throughput Functionally complete Small 24-pin DIP Low-power, 1.4 Watts Three-state output buffers No missing codes GENERAL DESCRIPTION INPUT/OUTPUT CONNECTIONS DATEL's ADS-111 is a 12-bit, functionally complete, sampling AID converter that is packaged in a space-saving 24-pin ceramic DIP. A minimum throughput rate of 500 KHz is achieved while only dissipating 1.4 Watts. Manufactured using thick-film and thin-film hybrid technology, a proprietary chip and unique laser trimming schemes, the ADS-111 's exclusive performance is based upon a digitallycorrected subranging architecture. PIN FUNCTION 1 2 3 4 5 6 7 8 9 10 11 12 ill BIT 12 OUT (LSB) BIT 11 OUT BIT 100UT BIT 9 OUT BIT 8 OUT BIT 7 OUT BIT60UT BIT 5 OUT BIT 4 OUT BIT30UT BIT2 OUT BIT lOUT (MSB) PIN FUNCTION 13 14 15 16 17 18 19 20 21 22 23 24 +5V DIGITAL GROUND EOC START CONVERT El\JAB[E (1-12) COMPBIN ANALOG INPUT BIPOLAR +10V REF +15V ANALOG GROUND -15V [[mEW +10V R E F @ l I - - - - - - - t - - + - - - - i DIGITAL CORRECTION LOGIC ANALOG 19 INPUT START CONV. me 22 +5V DIG. GND. For Immediate Assistance, Dial 1-800-233-2765 +15V ANAGND. -15V 1-1 ADS·111 ABSOLUTE MAXIMUM RATINGS OUTPUTS PARAMETERS LIMITS UNITS +15V Supply (Pin 22) -15V Supply (Pin 24) +5V Supply (Pin 13) o to +18 Volts dc Volts dc Volts dc Oto-18 -0.5 to +7.0 Digital Inputs (Pins 16, 17, 18) Analog Input (Pin 18) Lead Temp.(10 Sec.) Volts dc Volts dc -0.3 to +6.0 -15to +15 300 max °C MIN. TYP. MAX. UNITS - ±5 010 +10 15.0 3 - Vollsdc Volls dc MOhms pI 5.0 - 5 DIGITAL INPUTS logic levels Logic "1" Logic "0" Logic Loading "1" Logic Loading "0" 2.0 - - - - 0.8 5.0 -200 Vollsdc Volls dc ~ ~ ±3/4 ±3/4 ±2 LSB LSB LSB ±3/4 ±3/4 ±1 LSB LSB LSB AID PERFORMANCE Integral Non-Linearity +25°C o °C10 +70 °C -55 C to +125 °C Differential Non-Linearity +25°C 0°Clo+70°C -55 C 10 +125 °C Full Scale Absolute Accuracy +25°C 0°Cto+70°C -55 C 10 +125 'C Unipolar Zero Error, +25 °C (See Tech Note 1) LSB Unipolar Zero Tempco Bipolar Zero Error, +25 °C (See Tech Note 1) LSB Bipolar Zero Tempco Bipolar Offset Error, +25 'C (See Tech Note 1) LSB Bipolar Offset Tempco Gain Error, +25 °C (See Tech Note 1) Gain Tempco No Missing Codes (12 Bits) 1-2 - ±1/2 ±1I2 - ±1/2 ±1/2 - - ±5 ±6 ±10 ±10 ±18 ±32 LSB LSB LSB - ±3 ±5 ±15 ±30 ppm/oC - ±3 ±5 ±5 ±8 ppm/oC - ±4 ±8 - ±20 ±4 ±40 ±8 ppm/oC LSB - ±20 ±40 ppm/oC - - TYP. 2.4 - - +9.98 - +10.0 ±5 - MAX. UNITS 0.4 ·160 6.4 Volts dc Volts de ~ mA +10.02 ±30 1.5 Voltsdc ppm/oC mA 12 Bits Straight binary/offset binary Complementary binary Complementary offset binary DYNAMIC PERFORMANCE Apply over the operating temperature range and at ±15V dc and +5V dc unless otherwise specified. - MIN. Resolution Output Coding (Pin 18Hi) (Pin 18 Low) FUNCTIONAL SPECIFICATIONS ANALOG INPUTS Input Voltage Range ADS-111 (See Table 4 also) Input Impedance Input Capacitance Logic Levels Logic "1" Logic "0" Logic Loading "1" Logic Loading "0" Internal Reference Voltage, +25 'C Drift. External Current Over the Operating Temp. Range. Conversion Rate +25°C 0°Clo+70°C -55 C to +125 °C Total Harmonic Distortion DC to 60 KHz at Vin 5.5V p.p DC to 40 KHz at Vin = 10V p.p Slew Rate Aperture Delay Time Aperture Uncertainty S/H Acquisition Time to 0_01% (10V step) +25°C °C to +70 °C -55°C to +125 °C (Sinusoidal Input) 500 500 500 600 600 -65 -65 - -70 -70 90 20 ±100 - - - - dB dB V/I1Sec. nSec. pSec. - - 715 765 900 465 nSec. nSec. nSec. nSec. +15.0 -15.0 +5.0 +15.75 -15.75 +5.5 Volts dc Voltsdc Voltsdc +38 -36 +66 1.4 - +50 -47 +80 1.8 0.Q1 0 -55 - +70 +125 °C °C -65 - +150 °C - o - KHz KHz KHz - POWER REQUIREMENTS Power Supply Range + 15V dc Supply -15V dc Supply +5V dc Supply Power Supply Current + 15V dc Supply -15V dc Supply +5V dc Supply· Power DisSipation Power Supply Rejection 14.25 14.25 +4.5 - - mA mA mA Watts %FSR/% PHYSICAUENVIRONMENTAL Operating Temp_ Range -MC -MM/883B Storage Temperature Range Package Type Weight 24-pin hermetic sealed, ceramic DIP 0.42 ounces (12 grams) • +5V power usage at 1 TIL logic loading per data output bit. TECHNICAL NOTES 1. Applications which are unaffected by endpoint errors or remove them through software will use the typical connections shown in Figure 3. Remove system errors or adjust the small initial errors of the ADS-III to zero using the optional external circuitry shown in Figure 4. The external adjustment circuit has no affect on the throughput rate. 2. Rated performance requires using good high-frequency circuit board layout techniques. The analog and digital DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 0204B-1194ITEL (50B) 339-3000ITLX 1743BB/FAX (50B) 339-6356 ADS-iii grounds are not connected internally. Avoid ground-related problems by connecting the digital and analog grounds to one point, the ground plane beneath the converter. Due to the inductance and resistance of the power supply return paths, return the analog and digital ground separately to the power supplies. 3. Bypass the analog and digital supplies ~nd the +10V reference (pin 21) to ground with a 4.7 IlF, 25V tantalum electrolytic capaCitor in parallel with a 0.1 IlF ceramic capacitor. Bypass the +1 OV reference (pin 21) to analog ground (pin 23). 4. Obtain straight binary/offset binary output coding by tying COMI'Q31N (pin 18) to +5V dc or leaving it open. The device has an internal pull-up resistor on this pin. To obtain complementary bin1!'Y.P! cQ.rnplementary offset binary ou!:: ~ coding, tie the COMP BIN pin to ground. The COMP BIN signal is compatible to CMOSITTL logic levels for those users desiring logic control of this function. 5. To obtain three-state outputs, connect ENABLE (pin 17) to a logic "0" (low). Otherwise, connect ENABLE (pin 17) to a logic "I" (high). TIMING Figure 2 shows the relationship between the various input signals. The timing shown applies over the 0Pfilrating temperature range and over the operating power supply range. These times are guaranteed by design CALIBRATION PROCEDURE 1. Connect the converter per Figure 3, Figure 4, and Table 1 for the appropriate full-scale range (FSR). Apply a pulse of 200 nanoseconds minimum to the START CONVERT input (pin 16) at a rate of 250 KHz. This rate is chosen to reduce flicker if LED's are used on the outputs for calibration purposes. 2. Zero Adjustments Apply a preciSion voltage reference source between the amplifier's analog input and ground. Adjust the output of the reference source per Table 2. For unipolar, adjust the zero trimming potentiometer so that the output code flickers equally between 0000 0000 0000 and 0000 0000 0001 with the COMP BIN (pin 18) tied high (straight binary) or between 1111 1111 1111 and 1111 1111 1110 with pin 18 tied low (complementary binary). For bipolar operation, adjust the potentiometer such that the code flickers equally between 1000 0000 0000 and 1000 00000001 with (pin 18) tied high (offset binary) or between 011111111111 andOllllllllll0with(pin18)tiedlow (complementary offset binary). 3. Full-Scale Adjustment Set the output of the voltage reference used in step 2 to the value shown in Table 2. Adjust the gain trimming potentiometer so that the output code flickers equally between 1111 1111 1110 and 1111 1111 1111 for (pin 18) tied high or between 0000 0000 0001 and 0000 0000 0000 for (pin 18) tied low. 4. To confirm proper operation of the device, vary the precision reference voltage source to obtain the output coding listed in Table 4. Table 1. Input Range Selection INPUT RANGE INPUT PIN TIE TOGETHER NOTE: NOT DRAWN TO SCALE ±5Vdc o to+l0Vdc Pin 19 Pin 19 Pin 20 to Pin 21 Pin 20 to Ground START ,-[--"'-200 nSec MINIMUM ---l\ CONVERT Table 2. Zero and Gain Adjust FsR ZERO ADJUST +1/2 LsB o to +10V dc ±5Vdc GAIN ADJUST +Fs - 1 1/2 LsB +1.22mV dc +1.22mVdc +9.9963V dc +4.9963V dc INPUT RANGE R1 o to +10V, ±5V o to +5V, ±2.5V o to +2.5V, ±1.25V 2 2 2 R2 2 6 14 ~s n~~~!~~~I~I~I~N TIME (S~NISOIDAL INPUT) ..... 20 nSec. MINIMUM 1 35 nSec. MAXIMUM r'-----"~11 ~~ ~~:~. ~~~~~~ --ff-+-=--",o",..S=~:..:M,,-IN="'=UM INTERNAL SlH OUTPUT DATA =~ I ________ Enabled Data N-l Valid ..... 1 Table 3. Input Ranges (using external calibration) I I.L.!. I ---,,-,,£-,,<-,,--D_ata_N_Va_'~_ 10 nSec. MAXIMUM----"! 1-4- Enabled Data N Valid ~10 nSec MAXIMUM Figure 2. ADS-111 Timing Diagram UNIT KOhms KOhms KOhms For Immediate Assistance, Dial 1-800-233-2765 1-3 ADS-iii Table 4. Output Coding BIN CaMP BINARY STRAIGHT INPUT RANGE UNIPOLAR Oto +10V SCALE +9.. 9976V +FS -1 LSB 7/8 FS +8.7500V 3/4 FS +7.5000V +5.0000V 1/2 FS 1/4 FS +2.5000V 1/8 FS +1.2500V 1 LSB +0.0024V O.OOOOV 0 OUTPUT CODING MSB LSB MSB LSB 1111 1111 1111 0000 0000 0000 1110 0000 0000 0001 1111 1111 1100 0000 0000 0011 1111 1111 1000 0000 0000 0111 1111 1111 010000000000 101111111111 0010 0000 0000 110111111111 000000000001 111111111110 0000 0000 0000 111111111111 OFF. BINARY CaMP OFF BIN BIPOLAR SCALE +FS -1 LSB +3/4 FS +1/2 FS 0 -1/2 FS +3/4 FS -FS + 1 LSB -FS INPUT RANGES +4.9976V +3.7500V +2.5000V O.OOOOV -2.5000V -3.7500V -4.9976V -5.0000V R2' +15V To Pin 19 of ADS-l11 BIT 1 (MSB) BIT2 81T3 81T4 BIT5 81T6 OOMP BiN START START CONVERT-=--=--o--~ CONVERT ADS-lll 81T7 BIT 8 SIGNAL INPUT -.,-·v",V""l GAIN ADJUST BITS BIT 10 r-_----+SV TO PIN 19 OF ADS-118 + GAIN ADJUST 0.1 ~F 13 22 ANALOG INPUT +5Vdc START CONVERT 18 Figure 4b. Optional Unipolar Calibration Circuit 14 12 11 10 19 9 CciMP BiN 16 AD5-118 4 3 r-~....£J21'-l +10V REF 15 17 0.I~F1 lK BIT 1 (MSB) BIT 2 BIT 3 BIT 4 BITS BITS BIT7 BIT 8 BIT 9 BIT 10 BITll BIT12 dB o 0 0 30 40 50 50 EOC 70 EiiiAiiIE (1·12) 60 I ,I I I!H,[ I,,,, 0.5 I I 'IIJI Jj" 1.0 Figure 3. Typical ADS-118 Connection Diagram IUiI,,, ~J.u 11111;1, li,h 1.5 2.0 MHz Figure 5. FFT Analysis of ADS-118 MECHANICAL DIMENSIONS INCHES (MM) ORDERING INFORMATION 0.600 MAX ~ 0.190 MAX r--I~) ,-----r ..Q.150MIN. 0.010 x 0.018 112 131-rI 11 1.310 MAX. IBOTTOM I SPACES (33,3) I 11 I 1 AtO~I00 (2,5) 241~ ~;~~ SEAL AD8-118MC ADS·118MM ADS·EVAL2 a °C to +70 °C Hermetic -55°C to + 125 °C Hermetic Eva.lu,ation Board (without AOS-118) Receptacle for PC board mounting can be ordered through AMP Inc., Part # 3-331272-8 (Component Lead Socket), 24 required. 1 NOTE: Pins have 0.025 Inch ±O.01 standoff from case. 1-16 OPERATING TEMP. RANGE (3.8) KOVAR Pins VIEW MODEL NUMBER For availability of MIL-STO-883 versions of the ADS-118, contact DATEL. OATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194ITEL (508) 339-3000ITLX 174388/FAX (508) 339-6356 2.5 ADS-120 12-Bit, 20 MHz Sampling AID Converter ADVANCED PRODUCT DATA FEATURES • 12-Bit resolution • Internal Sample/Hold amplifier • 20 MHz minimum throughput • Samples up to Nyquist • Functionally Complete • Small 40-pin DIP • Low-power, 4.2 Watts • Three-State output buffers • High input bandwidth • Overflow pin INPUT/OUTPUT CONNECTIONS GENERAL DESCRIPTION DATEL's ADS-120 is a 12-bit, functionally complete, sampling ND converter packaged in a small40-pin DIP. A 20 MHz minimum throughput rate in digitizing sinusoidal signals is achieved while only dissipating 4.2 Watts. The ADS-120 is offered in the commercial 0 to +70 °C and military -55 to +125 °C operating temperature range. APPLICATIONS • Spectrum analysis • Imaging • Radar • Medical Instrumentation • High-speed Data Acquisition Systems PIN FUNCTION PIN FUNCTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 +15V -15V ANALOG GROUND ANALOG -5V ANALOG +5V ANALOG INPUT S/HOUT DIGITAL+5V DIGITAL GROUND DIGITAL-5V OFFSET ADJUST ANALOG +5V ANALOG GROUND ANALOG-5V GAIN ADJUST + 1OV REFERENCE +15V SUPPLY ANALOG -5V ANALOG GROUND ANALOG +5V 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 DIGITAL GROUND COMPBIN ENABLE DATA READY DIGITAL+5V START CONVERT OVERFLOW BIT 1 (MSB) BIT20UT BIT30UT BIT 4 OUT BIT 5 OUT BIT 6 OUT DIGITAL GROUND BIT 7 OUT BIT80UT BIT90UT BIT100UT BIT 11 OUT BIT 12 OUT (LSB) OFFSET ADJUST S1H OUT DIGITAL -5V DGND DIGITAL +5V 11 ANALOG IN 21·26, 28-34 GAIN ADJUST 12-BitOutput and Overflow PROPRIETARY 15 +10V REF 16 35 START CONVERT 21,22 1.17 NO CONNECTION + 15V -15V For Immediate ASSistance, Dial 1-800-233-2765 ANALOG ·5V AGND ANALOG +5V 1-17 Contact DATEL for up-to-date information on products covered by "Advanced" and "PreliminarY" product data sheets. Dial 1-800-233-2765 for Applications Assistance 1-18 DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194fTEL (508) 339-3000fTLX 174388/FAX (508) 339-6356 ADS-130 12-Bit, 10 MHz Sampling AID Converter FEATURES 6CIATEL • 12-Bit resolution • Internal Sample/Hold amplifier • 10 MHz minimum throughput • Samples up to Nyquist • Functionally Complete • Small 4O-pin DIP • Low-power, 3.85 Watts • Three-State output buffers • High input bandwidth • Overflow pin • No missing codes ~"Il.4Jitfl:'J..IItlt:: .....,.,..~ .,.tJS-/30MC INPUT/OUTPUT CONNECTIONS PIN FUNCTION PIN FUNCTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 +15V -15V ANALOG GROUND ANALOG-5V ANALOG+5V ANALOG INPUT S/HOUT DIGITAL+5V DIGITAL GROUND DIGITAL-5V OFFSET ADJUST ANALOG+5V ANALOG GROUND ANALOG-5V GAIN ADJUST + 1OV REFERENCE +15VSUPPLY ANALOG-5V ANALOG GROUND ANALOG+5V 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 DIGITAL GROUND COMPBIN ENABLE DATA READY DIGITAL+5V START CONVERT OVERFLOW BIT 1 (MSB) BIT20UT BIT30UT BIT40UT BIT 5 OUT BIT60UT DIGITAL GROUND BIT 7 OUT BIT 8 OUT BIT90UT BIT 10 OUT BIT 11 OUT BIT 12 OUT (LSB) GENERAL DESCRIPTION DATEL's ADS-130 is a 12-bit, functionally complete, sampling AID converter packaged in a small 40-pin DIP_ A 10 MHz minimum throughput rate in digitizing sinusoidal signals is achieved while only dissipating 3.85 Watts. SlH OFFSET OUT ADJUST 7 ANALOG IN GAIN ADJUST - 6 ~ SlH M""P~' r... ··,,'1A A 11 I FIRST STAGE CONVERSION I 15 10 + rr DGND DIGITAL ·5V I 9.27. 40 1 DIGITAL +5V B.36 I 2nd PASS SECOND STAGE CONVERSION ~ ,/" 38 E ERROR CORRECTION CKT. 1st PASS DATA :> 21-26,28-34 12-Bit output ... and Overflow 39 C REFERENCES +10V REF 37 16 0 ATA READY TIMING 35 START CONVERT 1, 17 1 +1SV 2 I -15V For Immediate Assistance, Dial 1-800-233-2765 4,14,18 1 ANALOG -5V 3,13,19 I AGND 5,12,20 I ANALOG +5V 1-19 AD5·130 ABSOLUTE MAXIMUM RATINGS LIMITS PARAMETERS +1SV Supply (Pin 1,17) -1SV Supply (Pin 2) +SV Supply (Pin 5, 8,12,20,36) -SV Supply (Pin 4,10,14,18) Digital Inputs (Pins 35,38,39) Analog Input (Pin 6) Lead Temp. (10 Sec.) UNITS DYNAMIC PERFORMANCE Oto +18 o to -18 -0.5 to +7.0 +0.5 to -7.0 Volts de Volts de Volts de Volts de -0.3 to +5.5 Volts de Volts de °C Conversion Rate (Changing Inputs),+25 °C o to+70OC -55 to +125 OC Total Harm. Distort.(-o.5 dB) DC to 500 KHz 500 KHz to 2.5 MHz 2.5 MHz to 5 Mhz Signal-to-Noise Ratio (w/o distortion, -0.5 dB) DC to 500 KHz 500 KHz to 2.5 MHz 2.5 MHz to 5 Mhz Signal-to-Noise Ratio and Distortion (-0.5 dB) DC to 500 KHz 500 KHz to 2.5 MHz 2.5 MHz to 5 Mhz Spurious Free Dynamic Range DC to 500 KHz (-0.5 dB)® 500 KHz to 2.5 MHz 2.5 MHz to 5 Mhz Effective Bits DC to 500 KHz SOO KHz to 2.5 MHz 2.5 MHz to 5 Mhz Two-tone Intermodulation Distortion ( fiN =2.2 MHz, 2.3 MHz, Fs = 8 MHz) Input Bandwidth Small Signal (-20 dB input) Full Power (0 dB input) Slew Rate Aperture Delay Time Aperture Uncertainty S/H Acquisition Time to 0.01% FS (2.5V step) +25 OC Oto +70 OC -55 to +125 OC Feedthrough Rejection 2.5V step Overvoltage Recovery, ±2.5 V ±5 300 FUNCTIONAL SPECIFICATIONS Apply over the operating temperature range and at ±15V dc and ±5V dc unless otherwise specified. INPUTS ANALOG Input Voltage Range Input Impedance Input Capacitance DIGITAL Logic Level "1" Logic Level "0" Logic Loading "1" Logic Loading "0" MIN TYP MAX - ±1.25 160 2.5 - 50 - 2.0 - - 10 0.8 5.0 -200 UNITS Vdc KOhm pF Vdc V dc ~ ~ OUTPUTS 12 Bits Resolution Output Coding (Pin 39 HI) (Pin 39 Low) Logic Level "1" Logic Level "0" Logic Loading "1" Logic Loading "0" Internal VREF, (pin 16) +25 OC oto+70 OC -55 to +125 OC External Current Offset Binary Complementary Offset Binary - - +9.9 +9.9 +9.8 +10.0 +10.0 +10.0 2.4 - - 0.4 Vdc Vdc -160 6.4 ~ +10.1 +10.1 +10.2 2 Vdc Vdc Vdc mA LSB LSB LSB mA PERFORMANCE Int. Non·Lin., flN= 5.0 MHz +25 OC a to +70 OC -55 to +125 OC Diff. Non-Lin., fiN = 5.0 MHz +25 OC oto+70 OC -55 to +125°C Full Scale Absolute Accuracy +25 OC (Tech note 1) Oto +70 OC -55 to +125 OC Bipolar Zero Error, +25 OC (Tech note 1) Oto +70 OC -55 to +125 °C Bipolar Offset Error, +25 OC (Tech Note 1) oto +70 OC -55 to +125 OC Gain Error, +25 OC (Tech Note 1) Oto+70OC -55 to+ 125 OC No Missing Codes (12 Bits, at fiN = 2.5 MHz) 1-20 MIN TYP MAX 10 10 10 - - MHz MHz MHz -68 -65 -65 -70 -67 -67 - FS,-dB FS,-dB FS,-dB -67 -65 -65 -70 -69 -69 - FS,-dB FS,-dB FS,-dB -65 -63 -63 -66 -65 -65 - FS, -dB FS,-dB FS,-dB -69 -66 -66 -70 -67 -67 - FS, -dB FS,-dB FS,-dB 10.6 10.2 10.0 11.0 10.5 10.2 - Bits Bits Bits -72 -75 - dB 50 30 175 - 65 40 200 5 5 7 7 MHz MHz V/!lSec nSec psec - 30 30 50 50 50 70 nSec nSec nSec -62 - -66 50 100 dB nSec +14.25 -14.25 +4.75 -4.75 +15.0 -15.0 +5.0 -5.0 +15.75 -15.75 +5.25 -5.25 Vdc Vdc Vdc Vdc - +26 -30 +347 -255 3.85 0.05 +28 -33 +372 -285 4.2 0.1 0 -55 -65 - - +70 +125 +150 UNITS POWER REQUIREMENTS - - ±1 ±1 ±2 - - ±1 ±1 ±2 LSB LSB LSB - ±D.2 ±D.4 ±D.8 ±D.4 ±D.8 ±1.6 %FSR %FSR %FSR - ±D.15 ±D.2 ±D.4 ±D.2 ±D.4 ±D.8 %FSR %FSR %FSR - ±D.15 ±D.2 ±D.4 ±D.2 ±D.4 ±D.8 %FSR %FSR %FSR ±D.15 ±D.2 ±D.4 ±D.2 ±D.4 ±D.8 %FSR %FSR %FSR - - - Power Supply Range +15V dc Supply (Vee) -15V dc Supply (VEE) +5V dc Supply (Voo) -5V dc Supppy (Vss) Power Supply Current +15V dc Supply -15V dc Supply +5V dc Supply® -5V dc Supply Power Dissipation Power Supply Rejection mA mA mA mA Watts %FSR/%V PHYSICAUENVIRONMENTAL Operating Temp. Range (Case) -MC -MM Storage Temperature Range Weight Package Type - °C °C °C 0.56 oz. (16 grams) Max. 40-Pin hermetic sealed, ceramic TDIP ® +5V power usage at 1 TTL logiC loading per data output bit. ~ The same specifications apply to In band Harmonics. DATEL, Inc. 11 Cabot BOUlevard, Mansfield, MA 02048-11941TEL (508) 339-30001TLX 174388/FAX (508) 339-6356 ADS·130 TECHNICAL NOTES CALIBRATION PROCEDURE 1. Use external potentiometers to remove system errors or to reduce the small initial errors to zero. Use a 20K trimming potentiometer for gain adjustment with the wiper tied to pin 15 (tie pin 15 to ANALOG GROUND for operation without adjustments). Use a 20K trimming potentiometer with the wiper tied to pin 11 for zer%ffset adjustment (tie pin 11 to ANALOG GROUND for operation without adjustment). 1. Connect the converter per Figure 2. Apply a pulse of 10 nS typical to the START CONVERT input (pin 35) at a rate of 500 KHz. This rate is chosen to reduce flicker if LED's are used on the outputs for calibration purposes. 2. Rated performance requires using good high-frequency circuit board layout techniques. Avoid ground-related problems by connecting the digital and analog grounds to one point, the ground plane beneath the converter. In most cases, users will use a single +5V supply for both analog +5V and digital +5V (applicable for the -5V supply also). Should users have separate supplies the difference between the analog and digital supply should be within ±100 mV to avoid performance degradation. Due to the inductance and resistance of the power supply return paths, return the analog and digital ground separately to the power supplies. This prevents contamination of the analog ground by noisy digital ground currents. 3. Bypass all the analog and digital power supply pins with a 2.2 !LF, 25V tantalum electrolytic capacitor in parallel with a 0.1 !LF ceramic capacitor to their respective analog and digital grounds. Use of chip capacitors is recommended. 4. Obtain offset binary output coding by tying COMP BIN (pin 39) to +5V dc. To obtain complementary offset binary output coding, tie pin 39 to ground. The pin 39 signal is compatible to CMOSITTL logic levels for those users desiring logic control of this function. 5. To obtain three-state outputs, connect the ENABLE pin (pin 38) to a logic "1" (high). Otherwise, connect pin 38 to a logic "0" (low). 6. The ADS-130 guarantees it's specified throughput rate over the temperature range when the START CONVERT pulse of 10 nS minimum, 90 nS maximum is provided at the specified rate. Start convert pulses greater than 90 nanoseconds will result in slower throughput rates. 7. The ADS-130 is capable of digitizing sinusoidal input frequencies up to the Nyquist frequency. The acquisition time for pulse or dc level signals is 50 nS maximum over the 0 to +70 °C temperature range. Acquisition time is 70 nSec. maximum from -55°C to + 125 °C. 8. The speCifications listed in Figure 2 (timing diagram) apply over the full operating temperature range unless otherwise specified. 2. Zero Adjustments Apply a precision voltage reference source between the analog input (pin 6) and analog ground. Adjust the output of the reference source per Table 2 for the bipolar zero adjustment (zero +1/2 LSB). Adjust the potentiometer such that the code flickers equally between 1000 0000 0000 and 1000 0000 0001 with COMP BIN (pin 39) tied high (offset binary) or between 0111 1111 1111 and 0111 1111 1110 with pin 39 tied low (complementary offset binary). 3. Full·Scale Adjustment Set the output of the voltage reference used in step 2 to the value shown in Table 2 for the bipolar gain adjustment (+FS -1 1/2 LSB). Adjust the gain trimming potentiometer so that the output code flickers equally between 1111 1111 1110 and 1111 1111 1111 with pin 39 tied high or between 000000000000 and 000000000001 with pin 39 tied low. To confirm proper operation of the device, vary the precision reference voltage source to obtain the output coding listed in Table 3. 35 37 S/H OUT 7 ANALOG IN 6 34 21-26 START CONVERT 3 3 15 + -15 15 + -15 20K 20K DATA READY OVERFLOW 912 ! OFFSET ADJ. GAIN ADJ. t 28-33 11 91 (MS9) 38 ENABLE 39 CQMPBIN 16 +10V REF 15 ADS-130 ANALOG-5V 4,14,18 ANALOGGND 3,13,19 ANALOG+5V 5,12,20 h-:C:-.-T-C=-b- -15V ~ANALOGGND 1,17 + +15V ea - is 2.2 f.tF tantalum Cb " is 0.1 J.lf ceramic Figure 2. Typical ADS·130 Connection Diagram 9. The OVERFLOW pin goes high for signals greater than +full scale (no overflow flag given for signals greater than -FS). The OVERFLOW pin is a three-state output and is enabled by pin 38. FSR 10.The ADS-130 has a one pipeline delay in obtaining output data. Refer to the Timing Diagram in Figure 3. ±1.25Vdc Table 2. Zero and Gain Adjust ZERO ADJUST o + 1/2 LSB GAIN ADJUST +FS ·11/2 LSB +305 !LV dc + 1.249085V dc 11.The ADS-130 goes into the hold mode on the rising edge of the start convert pulse. For Immediate Assistance, Dial 1-800'233-2765 1-21 ADS·130 FIN =180 KHz FIN H I S COUNT 26.40 23.76 21.12 18.48 I i I I ! i I I ! i i I I ! I I I I 13.20 10.56 I I 7.92 i I I I i I 15.84 , I I I COUNT 34 T I o I I I I = 949 KHz ! 5.28 2.64 2047 4095 CODe G R A M 17 T E S T S o .. ..... o 2047 4095 CODe D I F F L I N E A R I T Y dB dB -10 -10 I F F -20 -30 T I -20 I -30 -40 -50 -60 -70 I T -60 E -70 S T -90 'S -100 1.0 2.0 3.0 4.0 5.0 ,--- -_. -80 .•11'11, -90 il 1-22 I ,1l1li!M'll_ 1 o 1_0 3_0 2.0 I II", -100 MHz NOTE: ._-_.- f'---' I 4.0 MHz FCLOCK = 10 MHz for all presentations DATEL, Inc_ 11 Cabot Boulevard, Mansfield, MA 02048-1194fTEL (508) 339-3000fTLX 174388/FAX (508) 339-6356 ADS·130 FIN =1.89 MHz FIN H I COUNT 39.5 =4.85 MHz COUNT 29.6 S T o G R A M 19.75 ~ T E L..oIII\I .... S 4095 2047 14.8 T CODE S CODE D I .2047 4095 ISB +1.0 F F L I N E A R I T Y dB dB 0 F F T T E S -10 -20 -30 -40 -SO -eo -70 T S MIfz 11Hz NOTE: FCLOCK For Immediate Assistance, Dial 1-800-233-2765 = 1OMHz for all presentations 1-23 ADS .. 130 Table 3. Output Coding for Bipolar Operation BIPOLAR SCALE INPUT RANGE (Volts de) ±1.25V +1.24939V +0.9375V +0.625V O.OOOOV -0.625V -0.9375V -1.24939V -1.2500V +FS -1 LSB +3/4 FS +1/2 FS a -1/2 FS -3/4 FS -FS +1 LSB -FS OUTPUT CODING OFFSET BINARY COMP OFF. BINARY LSB MSB LSB MSB 111111111111 111000000000 1100 0000 0000 1000 0000 0000 0100 0000 0000 0010 0000 0000 0000 0000 0001 0000 0000 0000 0000 0000 0000 0001 1111 1111 001111111111 0111 1111 1111 1011 1111 1111 110111111111 111111111110 111111111111 100101-------- 100 nSec. Min. - - - - - _ " I --I 10 Min. 90 Max. nSec. ~ START CONVERT .....--- 85 nSec. Max•• 70 nSec. Min. DATA READY ~;-------....., 30 nSec. MIllC.1----N·2VALID OUTPUT DATA l~l !INVALlD! 30 nSec. Min. N·l VALID !INVALlD! N VALID COMPBIN ENABLE OUTPUT DATA 1--1 1--1 15 nSee. Max. 25 nSec. Max. 1---1 i-I 40 nSec. Max. 45 nSec. Max. NOTE: NOT DRAWN TO SCALE Figure 3. ADS-130 Output Data Timing MECHANICAL DIMENSIONS INCHES (mm) ~ 1.1 Max. (28,0) 0.150 (3.8) Min. +II" t "I1 - 0.190 (4.9) Max. I, U MODEL NUMBER 0.010 x 0.018 Kovar -t 20 Spaces a10.100 each (2.5) 20 21 Bottom View ADS-130 ORDERING INFORMATION T i ADS-130MC ADS-130MM 2.12 Max. ADS-B 130/131 Triangle on lop references Pin 1 *,/ 1 1 ~ 14" 0.900 0.100 (2.5) Nole: Pins have a 0.025 inch ±C.01 standoff from case 1-24 OPERATING TEMP. RANGE a to +70 °C -55 to +125 °C SEAL Hermetic Hermetic Evaluation Board (without ADS-130) Receptacle for PC board mounting can be ordered through AMP Inc., Part # 3-331272-8 (Component Lead Socket), 40 required. For availability of MIL-STD-883B versions, contact DATEL. DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-11941TEL (508) 339-30001TLX 174388/FAX (508) 339-6356 ADS-131 12-Bit, 5.0 MHz Sampling AID Converter FEATURES • 12-Bit resolution • Internal Sample/Hold amplifier • 5.0 MHz minimum throughput • Samples up to Nyquist • Functionally Complete • Small 40-pin DIP • Low-power, 3.65 Watts • Three-State output buffers • High input bandwidth • Overflow pin • No missing codes INPUT/OUTPUT CONNECTIONS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 GENERAL DESCRIPTION DATEL's ADS-131 is a 12-bit, functionally complete, sampling AID converter packaged in a small40-pin DIP. A 5_0 MHz minimum throughput rate in digitizing sinusoidal signals is achieved while only dissipating 3_65 Watts. SJH OFFSET ADJUST OUT 11 7 ANALOG IN GAIN ADJUST - 6 H SlH I FIRST STAGE CONVERSION I DGND 10 I 9.27,40 I FUNCTION 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 +15V -15V ANALOG GROUND ANALOG-5V ANALOG+5V ANALOG INPUT S/HOUT DIGITAL+5V DIGITAL GROUND DIGITAL-5V OFFSET ADJUST ANALOG+5V ANALOG GROUND ANALOG-5V GAIN ADJUST +10V REFERENCE +15VSUPPLY ANALOG-5V ANALOG GROUND ANALOG +5V DIGITAL -5V + ? PIN FUNCTION PIN DIGITAL GROUND COMPBIN ENABLE DATA READY DIGITAL+5V START CONVERT OVERFLOW BIT1 (MSB) BIT 2 OUT BIT30UT BIT 4 OUT BIT 5 OUT BIT 6 OUT DIGITAL GROUND BIT 7 OUT BIT80UT BIT90UT BIT 10 OUT BIT11 OUT BIT 12 OUT (LSB) DIGITAL+5V 8.36 I 2nd PASS DAT~ SECOND STAGE CONVERSION 38 .> E .... 21-26,28 ERROR CORRECTION CKT. 1s1 PASS DATA 15 :> 12·Btt OU1pu1 and Overflow ~ 39 C REFERENCES +10V 37 REF 16 0 ATAREADY TIMING 1, 17 1 +15V 2 I -15V For Immediate Assistance, Dial 1-800-233-2765 4,14,18 1 ANALOG -5V 3,13,19 I AGND 5,12,20 35 S TART CONVERT I ANALOG +5V 1-25 ADS·131 ABSOLUTE MAXIMUM RATINGS LIMITS UNITS AID PERF. CONT. +15V Supply (Pin 1,17) -15V Supply (Pin 2) +5V Supply (Pin 5, 8,12,20,36) -5V Supply (Pin 4,10,14,18) PARAMETERS 010+18 010-18 -O.Slo +7.0 +O.S to -7.0 Volts de Valls de Valls de Volts de Digital Inputs (Pins 35,38,39) Analog Input (Pin 6) Lead Temp.(10 Sec.) -0.310 +S.S ±S 300 Volts de Valls de Gain Error, +25 'C (Tech Note 1) oto +70 'C -55 to +125 "C No Missing Codes (12 Bits. at fiN = 2.5 MHz) ·C FUNCTIONAL SPECIFICATIONS Apply over the operating temperature range and at ±15V de and ±5V de unless otherwise specified. INPUTS Analog Inpul Voltage Range Input Impedance Inpul Capacitance Digital Logic Levels Logic "1" Logic "0" Logic Loading "1" Logic Loading "0" MIN TYP MAX - ±1.25 160 2.5 - 50 - 2.0 - - - - 10 0.8 5.0 ·200 UNITS Vde KOhm pF Vde Vde IIA IIA OUTPUTS Resolution Output Coding (Pin 39 HI) (Pin 39 Low) Logic Levels Logic "1" Logic "0" Logic loading "1" logic Loading "0" Internal Relerence VoHage, (pin 16) +25"C Oto +70 "C ·55 to +125 "C External Current 2.4 - +9.9 +9.9 +9.8 - - +.10.0 +10.0 +10.0 - 0.4 ·160 6.4 +10.1 +10.1 +10.2 2 Vde Vde IIA rnA Vde Vde Vde rnA PERFORMANCE Inl. Non-l.ln., fIN:: 2.5MHz +25"C Oto+70"C -55to+t25"C. DHI. Non-I.ln.,fIN =2.5MHz +25"C Oto+70"C ·55to+125"C Full Scale Absolute Accuracy +25 "C (Tech note 1) Oto+70"C ·55to+125"C Bipolar Zero Error, +25 "C (Tech note 1) Oto+70"C -55 to +125 "C Bipolar Offset Error, +25 "C (Tech Note 1) Oto+70"C -55 to +125 'C 1-26 - Conversion Rate (Changing Inputs).+25 'C o 10 +70 'C ·55 10 +125 "C Total Harm. Dlstort.(-o.5 dB) DC 10500 KHz 500 KHz 10 2.5 MHz Signal-to-Noise Ratio (wlo distortion, -0.5 dB) DC to 500 KHz 500 KHz to 2.5 MHz Signal-Io-Noise Ratio and Distortion (-0.5 dB) DC to 500 KHz 500 KHz to 2.5 MHz Spurious Free Dynamic Range® DC 10500 KHz 500 KHz to 2.5 MHz Effective Bits DC to 500 KHz 500 KHz to 2.5 MHz Two-tone Intermodulatlon Distortion ( fiN =2.2 MHz, 2.3 MHz, Fs = 5 MHz) Input Bandwidth Small Signal (-20 dB inpul) Full Power (0 dB input) Slew Rate Aperture Delay Time Aperture Uncertainty SlH Acquisition Time to 0.01% FS (2.5V step) +25"C 010+70'C -55 10 +125 'C Feedthrough Rejection 2.5V step Overvoltage Recovery, :12.5 V MAX UNITS - :10.15 :10.2 :10.4 :10.2 :10.4 :10.8 %FSR %FSR %FSR Over Operating Temperature Range - - MHz MHz MHz - FS,·dB FS,-dB -70 -69 - FS,·dB FS,-dB -66 -65 - FS,-dB FS,-dB -68 -65 -70 -67 - FS,-dB FS,-dB 10.6 10.2 11.0 10.5 - bits bits -72 -75 - dB 50 30 75 - - 65 40 100 5 5 MHz MHz VI!lSee nSec psec - 50 50 70 5.0 5.0 5.0 - - -68 -65 ·70 -67 - -67 -65 -65 -63 - - 7 7 70 70 100 nSec nSee nSec - 100 200 - dB nSec +14.25 ·14.25 +4.75 ·4.75 +15.0 ·15.0 +5.0 -5.0 +15.75 -15.75 +5.25 -5.25 Vde Vde Vde Vdc - +25 -30 +310 -250 3.65 0.05 +2S -33 +342 -275 4.00 0.1 rnA rnA rnA rnA ·62 ·66 POWER REQUIREMENTS Power Supply Range +15V de Supply (Vee) -15V de Supply (VEE) +5V de Supply (Voo) -5V de Supppy (Vss) Power Supply Current +15V de Supply -15V de Supply +5V de Supplycr> -5V de Supply Power Dlssipelion Power Supply Rejection ±1 ±1 :12 LSB LSB LSB ±1 ±1 :12 LSB LSB LSB :10.2 :10.4 :IO.S :10.4 :10.8 ±1.6 %FSR %FSR %FSR PHYSICAl/ENVIRONMENTAL - :10.15 :10.2 :10.4 :10.2 :10.4 :IO.S %FSR %FSR %FSR - :10.15 :10.2 :10.4 :10.2 :10.4 :IO.S %FSR %FSR %FSR Operating Temp. Range -MC -MM Storage Temperature Range Weight Package Type - TYP DYNAMIC PERFORMANCE - - MIN - - Watts %FSR/%V - ·C +70 ·C +125 ·C +150 0.56 oz. (16 grams) Max. 4O-Pin hermetic sealed, ceramic TDIP 0 -55 -65 - cr> +5V power usage at 1 TTL logic loading per data output bit. ® The same specifications apply to Inband Harmonics. DATEL, Inc. 11 Cabot Boulevard, Mansfield. MA 02048-1194fTEL (508) 339-3000fTLX 174388/FAX (S08) 339-6356 ADS·131 TECHNICAL NOTES CALIBRATION PROCEDURE 1. Use external potentiometers to remove system errors or to reduce the small initial errors to zero. Use a 20K trimming potentiometer for gain adjustment with the wiper tied to pin 15 (tie pin 15 to ANALOG GROUND for operation without adjustments). Use a 20K trimming potentiometer with the wiper tied to pin 11 for zer%ffset adjustment (tie pin 11 to ANALOG GROUND for operation without adjustment). 1. Connect the converter per Figure 2. Apply a pulse of 10 nS typical to the START CONVERT input (pin 35) at a rate of 500 KHz. This rate is chosen to reduce flicker if LED's are used on the outputs for calibration purposes. 2. Rated performance requires using good high-frequency circuit board layout techniques. Avoid ground-related problems by connecting the digital and analog grounds to one pOint, the ground plane beneath the converter. In most cases, users will use a single +5V supply for both analog +5V and digital +5V (applicable for the -5V supply also). Should users have separate supplies the difference between the analog and digital supply should be within ±100 mV to avoid performance degradation. Due to the inductance and resistance of the power supply return paths, return the analog and digital ground separately to the power supplies. This prevents contamination of the analog ground by noisy digital ground currents. 3. Bypass all the analog and digital power supply pins with a 2.2 ~F, 25V tantalum electrolytic capacitor in parallel with a 0.1 ~F ceramic capacitor to their respective analog and digital grounds. Use of chip capacitors is recommended. 4. Obtain offset binary output coding by tying COMP BIN (pin 39) to +5V dc. To obtain complementary offset binary output coding, tie pin 39 to ground. The pin 39 signal is compatible to CMOSmL logic levels for those users desiring logic control of this function. 2. Zero Adjustments Apply a precision voltage reference source between the analog input (pin 6) and analog ground. Adjust the output of the reference source per Table 2 for the bipolar zero adjustment (zero +1/2 LSB). Adjust the potentiometer such that the code flickers equally between 1000 0000 0000 and 100000000001 with COMP BIN (pin 39 tied high (offset binary) or between 011111111111 and 011111111110with pin 39 tied low (complementary offset binary). 3. Full·Scale Adjustment Set the output of the voltage reference used in step 2 to the value shown in Table 2 for the bipolar gain adjustment (+FS -1 1/2 LSB). Adjust the gain trimming potentiometer so that the output code flickers equally between 1111 1111 1110 and 1111 1111 1111 with COMP BIN (pin 39) tied high or between 0000 0000 0000 and 0000 0000 0001 with pin 39 tied low. To confirm proper operation of the device, vary the precision reference voltage source to obtain the output coding listed in Table 3. 7. The ADS-131 is capable of digitizing sinusoidal input frequencies up to the Nyquist frequency. The acquisition time for pulse or dc level signals is 70 nS maximum over the 0 to +70 °C temperature range. Acquisition time is 100 nSec. maximum from -55°C to +125 DC. 8. The specifications listed in Figure 3 (timing diagram) apply over the full operating temperature range unless otherwise specified. 37 SlHOUT OVERFLOW .,2 1 3 3 15 + 20K -15 OFFSET 15 + 20K -15 GAIN ANALOO-5V DATAAEADY 34 21-26 ANALOG IN 5. To obtain three-state outputs, connect ENABLE (pin 38) to a logic "1" (high). Otherwise, connect pin 38 to a logic "0" (low). 6. The ADS-131 guarantees it's specified throughput rate over the temperature range when the START CONVERT pulse of 10 nS minimum, 190 nS maximum is provided at the specified rate. Start convert pulses greater than 190 nanoseconds will result in slower throughput rates. 35 START CONVERT ADJ. ADJ. 28-33 38 11 15 AD5-131 CO 1 ., (MS.) ENABLE 3. COMPBIN ,. +10V REF H--:c,---.--1-:CC--.--15V ~ANALOGGND 1,17 ca - is 2.2 pF tantalum +15V Cb - is 0.1 jlf ceramic Figure 2. Typical ADS·131 Connection Diagram 9. The OVERFLOW pin goes high for signals greater than +full scale (no overflow flag given for signals greater than -FS). The OVERFLOW pin is a three-state output and is enabled by the ENABLE line (pin 38). FSR 10.The ADS-131 has a one pipeline delay in obtaining output data. Refer to the Timing Diagram in Figure 3. ±1.25Vdc Table 2. Zero and Gain Adjust ZERO ADJUST o + 1/2 LSB GAIN ADJUST +FS ·11/2 LSB +305 ~Vdc +1.249085V dc 11.ADS-131 goes into the1rold mode on the rising edge of the start convert pulse. ~ For Immediate Assistance, Dial 1-800-233-2765 1-27 ADS·131 .It"""" ":cnE' FIN = 95 KHz FIN H I S T COUNT 26.40 23.76 21.12 18.48 o 15.84 G 13.20 R 10.56 A M 7.92 5.28 17 E 4095 2047 COUNT 34 ... T .J 2.64 =495 KHz CODE D I LSB I... S T S o o 2047 CODE 4095 LSB +0.9 F F 2047 4095 CODE L I N E A R I T Y dB CODE dB F F T -10 -20 -30 -10 -20 -30 -40 -40 -SO -50 -60 -70 -80 -90 -100 T III 1 !1.1 oJlMf' E .... ,oJl, diu, 1 .•1 •. 1lL .....,' h ..M1I 1.5 2 2.5 S T S -60 -70 -80 :~~' -90 1,1Il'.lJ -100 1 MHz NOTE: 1-28 1.5 2 2.5 MHz FCLOCK = 5 MHz for all presentations DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194fTEL (508) 339-3000fTLX 174388/FAX (508) 339-6356 ADS·131 .:;;;SW.WZUU;;MYPJ;;;.·,Q¥AAIZO.Qi&¥U,th" a&USCtM4I4MtU4U¥l! FIN £ = 985 KHz FIN H I S T COUNT 39.5 = 2.45 MHz COUNT 29.6 o G R A M 19.75 14.8 T Mo.. o E l.oIIII o 2047 4095 COOE S T S D I o - o 2047 4095 CODE LSB F F L I N E A R I T Y dB dB ·10 ·10 ·20 ·30 ·40 F F T ·20 T ·60 ·50 ·60 ·70 ·80 ·90 E Ild~11 IIIid IlIwi l1 -100 1.5 .5 .u 2.5 S T S -30 ·40 ·50 -70 ·80 ·90 -100 MHz MHz NOTE: FCLOCK = 5 MHz for all presentations For Immediate Assistance, Dial 1-800-233-2765 1-29 7 Table 3. Output Coding for Bipolar Operation BIPOLAR SCALE INPUT RANGE .(Volts dc) ±1.25V +FS -1 LSB +3/4 FS +1/2 FS +1.24939V +0.9375V +0.625V -1/2 FS -3/4 FS -FS +1 LSB -FS -0.625V -0.9375V -1.24939V -1.2500V a OUTPUT CODING OFFSErBINARY . COMP OFF. BINARY MSB LSB MSB LSB 111111111111 1110 0000 0000 1100 0000 0000 1000 0000 0000 0100 0000 0000 0010 0000 0000 0000 0000 0001 0000 0000 0000 o.oooov fool-e-------- . 0000 0000 0000 ,000111111111 0011 1111 1111 0111 1111 1111 1011 1111 1111 110111111111 ~111111111110 1111 11111111 200 nSec. Min. - - - - - - "I 10 Min. 190 Max. nSec. - I I-START CONVERT _ DATA READY 100nSec. Max._~--------, ±5nSec. 30 nSec. Min. 30 nSec. Max. j . - - I_ I N·2VALID 'OUTPUT DATA IINVAlID I N-1 VAliD I INVALID I N VALID COMPBINENABLE OUTPUT DATA 1---1 1--1 25 nSec. Max. 15 nSec. Max. 1---1 I-I 40 nSec. Max. 45 nSec. Max. NOTE: NOT DRAWN TO SCALE Figure 3. ADS-131 Output Data Timing MECHANICAL DIMENSIONS INCHES (mm) ~ I -1';2~~' • I +I I I TI, 0.150 (3,8) Min. U t 0.190 (4,9) Max. ORDERING INFORMATION MODEL NUMBER ADS-131MC ADS-131MM OPERATING TEMP,RANGE SEAL a to +70 DC -55 to +125 DC Hermetic Hermetic 0.010 x 0.018 Kovar -t 20 Spaces .'0.100 each (2,5) ! Triangle on top references '20 "j, Bottom VIew ADS-131 I ,I I ,I I I .. I ,;' -~!~~t II i 1 Pin 1 Note: Pins have a 0.025 inch ±O.01 1-30 TP20K 2.12 Max. _ _ 0.100(2,5) standoff from case . Part Number ADS-B130/131 Description Trimming Potentiometer (2 required) Evaluation Board (without ADS-131) Receptacle for PC board mounting can be ordered through AMP Inc.• Part # 3-331272-8 (Component Lead Socket). 40 required. For availability of MIL-STD-883B versions. contact DATEL. DATEL. Inc. 11 Cabot Boulevard. Mansfield. MA 02048-1194ITEL (508) 339-3000ITLX 174388/FAX (508) 339-6356 ADS-132 12-Bit, 2.0 MHz, Low-Power Sampling AID Converter FEATURES • • • • • • • • • 12-Bit resolution Internal Sample/Hold 2.0 MHz minimum throughput Functionally complete Small 32-pin DIP Low-power, 2.9 Watts Three-state output buffers Samples up to Nyquist No -5V supply required INPUT/OUTPUT CONNECTIONS PIN GENERAL DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 DATEL's ADS-132 is a 12-bit, functionally complete, sampling AID converter.rthat is packaged in a small 32-pin ceramic DIP. The ADS-132 digitizes sinusoidal signals at a 2.0 MHz minimum throughput rate while dissipating only 2.9 Walts. ..v -15V .15V +10V REF. OUT RANGE INPUT HIGH INPUT LOW OFFSET ADJUST OVERFLOW COMP.BIN StROUT BIPOLAR ENABLE (1 - 12) +5 DIGITAL GROUND +15V -15V DO NOT CONNECT ANALOG GROUND 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 FUNCTION DO NOT CONNECT EOC BIT 12 OUT (LSB) BIT 11 OUT BIT100UT BIT90UT BIT80UT BIT 7 OUT BIT60UT BIT50UT BIT40UT BIT 3 OUT BIT20UT BIT lOUT (MSB) START CONVERT GAIN ADJUST OVERFLOW 141 11 GAIN ADJUST PIN FUNCTION ~32~_ _ _ _ _ _- - , +10VREF BIPOLAR INPUT HIGH RANGE S/HOUT BIT 7 BIT8 BIT. BlT1. BIT 11· BIT 12 (LSB) OfFSET ADJUST COMPBiN -1 START CONVERT ..;:31+_ _ _ 1. DO NOT CONNECT ...:"'-!---__-I INPUT LOW 12 00 NOT CONNECT For Immediate Assistance, Dial 1-800-233-2765 1. ANALOG GROUND 1-31 ADS·132 ABSOLUTE MAXIMUM RATINGS PARAMETERS +15V Supply (Pin 13) -15V Supply (Pin 14) +5V Supply (Pin 11) LIMITS UNITS o to +18 Voltsdc Voltsdc Volts dc Oto -18 -0.5 to +7.0 Digital Inputs (Pins 7, 10, 31) Analog Input (Pin 3) Lead Temp. (10 Sec.) -0.3 to +6.0 -15 to +15 300 max Volts dc Volts dc °C Logic Levels Logic "1" Logic "0" Logic Loading "1" Logic Loading "0" Internal Reference Voltage, +25 'C Drift External Current FUNCTIONAL SPECIFICATlON.S· DYNAMIC PERFORMANCE Apply over the operating temperature'range and at 15±V dc and +5V dc unless otherwise specified. Conversion Rate, 12-Bits Total Harm. Distorq-o.S dB) DC to 100 KHz 100 KHz 10 500 KHz 500 KHz 10 1 MHz Signal to Noise Ratio (w/o distort., -0.5 dB) DC to 100 KHz 100 KHz to 500 KHz 500 KHz to 1 MHz Signal-to-Noise Ratio (with distort., -0.5 dB) DC to 100. KHz 100 KHz to 500 KHz 500 KHz to 1 MHz Eflectille Bits, -0.5 dB DC to 100 KHz 100 KHz to 500 KHz 500 KHz to 1 MHz Two-Tone Intermodulation Distort. (fin = 490. KHz, 480 KHz, Fs = 2 MHz, -0.5 dB Input Bandwidth Small Signal (-20 dB input) Full Power (0 dB input) Slew Rate Aperture Delay Time Aperture Uncertainty Feedthrough Rejection S/H AcquiSition Time to 0.01 %FS (1 OV step) S/H Acquisition Time to 0.1% FS (10V step) ANALOG INPUTS Input Voltage Range ADS-132 (See Table I also) MIN. TYP. MAX. UNITS - 010 -5 o to -10 Oto -20 o to +10 ±5 ±IO - Valls de Volts de Volts de Volts de Voltsdc Volts de - Input Impedance Input Ranges: (0 to -10, -20, +10,±10) (0 to -5, ±5V) Input Capacitance 800 400 - - - 1,000 500 2 - - O.S 5.0 -200 - Ohms Ohms pi DIGITAL INPUTS Logic Levels Logic "I" Logic "0" Logic Loading "I" Logic.Loading "0" 2.0 - PERFORMANCE. Integral Non·Linearity @FlN=IMHz +25 'C o 'Cto +70'C -55'C to +125'C Differential Non-Linearity @FIN=IMHz +25 'C O'Cto+70'C -55 'c to+ I 25 'C Full Scale Absolute Accuracy (See Tech Note II +25 'C. o 'Cto +70'C -55'C to +125'C Unipolar Zero Error +25'C (See Tech Note 1) 0°Cto+70'C -55'C to +125°C Bipolar Zero Error +25'C (See Tech Note 1) o 'Cto +70'C -55'C to +125'C Bipolar Offset Error, +25 'C (See Tech Note t I Bipolar Offset Tempeo Gain Error, +25 'c (See Tech Note 1) Gain Tempeo No MISSing Codes (12 Bits) 1-32 - - - - - ±3/4 ±3/4 - - ±1.5 - - ±3/4 ±3/4 - ±D.I - ±D.13 ±D.2 ±0.25 ±0.32 - - ±1.5 ±D.5 - ±D.05 ±O.I ±0.t3 ±0.25 - ±D.t8 ±D.37 - ±O.05 - ±D.l - ±0.18 - ±D.l - ±17 Volts de Volts dc' IlA IlA LSB LSB LSB LSB LSB LSB %FSR %FSR %FSR %FSR %FSR %FSR ±0,13 ±0.25 ±0.37 %FSR %FSR %FSR ±17 ±O.2 ±35 ±D.08 ±D.17 %FSR ppm/oC %FSR ±35 ppm/'C MIN. 2.4 - +9.98 - I TYP. +10.0 ±5 - - Voltsdc Volts dc IlA mA 0.4 -160 4.8 +10.02 ±30 2 Voltsdc ppm/'C mA 2 - - MHz -72 -70 -67 -80 -75 -71 - FS.-dB FS,-dB FS, -dB -70 -68 -66 -72 -70 -68 - - - FS.-dB FS,-dB FS, -dB -68 -66 -65 -70 ·68 -67 - FS,-dB FS,-dB FS,-dB 11.0 10.7 10.4 11.25 11.1 11.0 - Bits Bits Bits -67 -70 - FS,-dB 16 8 - - MHz MHz V/IlSec, nSec. pSec. dB - - - - 300 6 5 -74 - 160 180 nSec. - 100 150 nSec. 14.25 -14.25 +4.75 +15.0 -15,0 +5.0 +15,75 -15.75 +5.25 Voltsdc Volts dc Volts dc - +75 -60 +t55 2.9 +82 -68 +200 3.2 0.01 rnA rnA rnA Watts %FSR/%V +70 +125 'c - 40 POWER REQUIREMENTS Power Supply Range. + 15V dc Supply -15V dc Supply +5V de Supply Power Supply Current +15V dc Supply -15V dc Supply +5V dc Supply (j) Power Dissipation Power Supply Rejection - - PHYSICAUENVIRONMENTAL Operating Temp. Range, Case -MC -MM Storage Temperature Range Package Type Weight (j) Over the Operating Temp. Range. I MAX. I UNITS 12 Bits Straight binary/offset binary Complementary binary/Complementary offset binary OUTPUTS Resolution Output Coding 0 -55 - 'C -65 +150 'C 32-pin hermetic sealed, ceramic DIP 0.42 ou-nces (12 grams) +5V power usage at 1 TTL logiC loading per data output bit. Specifications subject to change without notice, DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194n-EL (508) 339-3000n-LX 174388/FAX (508) 339-6356 ADS·132 TECHNICAL NOTES 1. Use external potentiometers to remove system errors or the small initial errors to zero. Use a 20K trimming potentiometer for gain adjustment with the wiper tied to pin 32 (ground pin 32 for operation without adjustments). Use a 20K trimming potentiometer with the wiper tied to pin 5 for zerol offset adjustment (leave pin 5 open for operation without adjustment). See Figure 3. 2. Rated performance requires using good high-frequency circuit board layout techniques. The analog and digital grounds are not connected internally. Avoid ground-related problems by connecting the digital and analog grounds to one pOint, the ground plane beneath the converter. Due to the inductance and resistance of the power supply return paths, return the analog and digital ground separately to the power supplies. 3. Bypass the analog and digital supplies and the +10V reference (pin 1) to ground with a 4.7 ~F, 25V tantalum electrolytic capacitor in parallel with a 0.1 ~F ceramic capacitor. Bypass the +1 OV reference (pin 1) to analog ground (pin 16). 4. To enable the three-state outputs, connect ENABLE (pin 10) to a logic "0" (low). To disable, connect ENABLE (pin 10) to a logic "1" (high). 5. The ADS-132 is in the sample mode when the internal S/H CONTROL pin is high (S/H is in the high-state on powerup). The START CONVERT pulse should be given at a time delay equal to the desired acquisition time minus the 10 nanosecond delay from START CONVERT high to S/H CONTROL low. This assures the sample-hold has the minimum required acquisition time for the particular application mode. 6. Upon going into the hold mode there will be a 85 nanosecond maximum delay before EOC goes high and the AID conversion begins. This consists for the remaining 50 nanoseconds of the START CONVERT (10 nanoseconds is part of the acquisition time) and a 20 nanosecond maximum delay from START CONVERT low to EOC high. The hold mode settling time requirement is met during this time. 7. Figure 2 shows the relationship between the various input signals. The timing shown applies over the operating temperature range and over the operating power supply range. These times are guaranteed by design. CALIBRATION PROCEDURE 1. Connect the converter per Figure 3, and Tables 1 and 4 for the appropriate full-scale range (FSR). Apply a pulse of 60 nanoseconds minimum to the START CONVERT input (pin 31) at a rate of 500 KHz. This rate is chosen to reduce flicker if LED's are used on the outputs for calibration purposes. 2. Zero Adjustments Apply a preciSion voltage reference source between the amplifier's analog input and ground. Adjust the output of the reference source per Table 2. For unipolar, adjust the zero trimming potentiometer so that the output code flickers equally between 0000 0000 0000 and 0000 0000 0001 (straight binary) or between 1111 1111 1111 and 1111 1111 1110 (complementary binary). For Immediate Assistance, Dial 1-800-233-2765 For bipolar operation, adjust the potentiometer such that the code flickers equally between 1000 0000 0000 and 1000 0000 0001 (offset binary) or between 0111 1111 1111 and 0111 1111 1110 (complementary offset binary). 3. Full-Scale Adjustment Set the output of the voltage reference used in step 2 to the value shown in Table 2. Adjust the gain trimming potentiometer so that the output code flickers equally between 1111 1111 1110 and 1111 1111 1111 (offset binary) or between 000000000001 and 0000 0000 0000 (complementary offset binary). 4. To confirm proper operation of the device, vary the precision reference voltage source to obtain the output coding listed in Table 3. Table 1. ADS-132 Input Range Selection INPUT RANGE INPUT PIN o to-5V dc o to -10V dc o to +10V dc Pin3 Pin3 Pin3 Oto-20V dc ±5Vdc ±10V dc Pin 3 Pin 3 Pin 3 TIE TOGETHER Pin 8 to Pin 9, Pin 2 to Pin 3 Pin 8 to Pin 9 Pin 8 to Pin 9, Pin 2 to EXT.-l0V Reference· Pin 1 to Pins 2 & 9 Pin 1 to Pin 9, Pin 2 to Pin 3 Pin 1 to Pin 9 • EXT -10V REF may be referenced to pin 1, EXT +1 OV REF Table 2. Zero and Gain Adjust -0.61 mV -1.22mV +1.22 mV -2.44 mV +1.22mVdc +2.44 mVdc Oto -5V dc Oto-l0Vdc Oto+l0Vdc Oto -20V dc ±5Vdc ±10V dc STAAT -4.9982V dc -9.9963V dc +9.9963V dc -19.9927V dc +4.9963Vdc +9.9927Vdc ~60nSecI±25nSec ! ! CONVERT EoC GAIN ADJUST +FS - 1 1/2 LSB ZERO ADJUST + 1/2 LSB FSR j ~ FF;::::-~10~"Sec~",~"--1..____ --I LL "Sec min INTERNALS/A ;::L25 nSec m: nSec max ---=:..., I OUTPUT DATA Data N-1 Valid I . - - - 350 nSec min I fI- 75 j L IXIXIXJ --I 35 oSec max Data N Valid E_od 30 nSec max::::t ENABLE DATA - - - - - - - - ' NOTE: Retrig9!d..ng the START CONVERT before EOC goes row w~r not begin anewconversiDn. NOTE: NOT DRAWN TO SCALE I-- e: N I~~~~D [8l Figure 2. ADS-132 Timing Diagram 1-33 ADS·132 Table 3. Output Coding STRAIGHT UNIPOLAR INPUT RANGES, V de ~----~------~----~~--~~--~ Bill COUP BII1ARY INPUT RANGE OUTPUT CODING 1111 1111 1111 1110 0000 0000 1100 0000 0000 1000 0000 0000 0100 0000 0000 001000000000 0000 0000 0001 0000 0000 0000 OFF BltlARY -2.5000V O.OOOOV -2.5000V -3.7500V -4.9976V -S.OOOOV corlP OFF 10V +9.9951V +7.5000V +5.0000V O.OOOOV -5.0000V -7.5000V -9.9951V -10.000V BIPOLAR ALE +FS-l LSB +3I4FS +112 FS o -1/2 FS -3/4 FS -FS+l LSB -FS Bill Table 4. COMP BIN (Pin 7) Connection INPUT RANGE BINARY I COMPLEMENTARY BINARY Pin 7 logic state" .15V +15V 32 ANA. -15V o to +10V .5V GAIN ADJUST IN 10 30 29 28 27 28 25 24 23 22 21 20 AD5-132 ·1!5V +1OV REF. OUT BIPOlAR INPUT 0.1 4.7 "'J .FJ Si'HOUT ANA. INPUT HI ,. 'RANGE IN ANA. INPUT LO ,.V ---1l..- BIT 1 OUT (MBB) BIT 2 OUT BIT30UT BIT40UT BIT 5 OUT BIT60UT BIT 7 OUT BIT80UT BIT 9 OUT BIT 10 OUT 81Tl1 OUT BIT 12 OUT (LSB) " For logic state low connect to +5V. For logic state high leave open. ,. "EOC ·10 00MPiiN 31 ENABi:E (1-12) 6 START CONVERT IN High Low Low Low High High Low High High High Low Low Oto-5V Oto -10V Oto -20V ±5V ±10V GND OVERFLOW ZERO I OFFSET ... 1--1--1--1--1--1--1--1--1--1-+1 ~I--I--I--I--I--I--I--I--I--I-~ ~~-~-~-~-~-~-~-~-~-~~ ADJUST IN ~I--I--I--I--I--I--I--I--I--I-~ +15V ~~--~--~--~--~--~--~--~--~--~~ -15V ~I-+-hr-I--I--I---I---I---I---I---rr-~ 200 ~~+-r.r--r,--~h-~r-rr-r-rr-~r+r-rr.HrKr Figure 3. Typical ADS-132 Connection Diagram, ±10V dc 100 200 300 400 500 800 700 800 900 1000 kHz MECHANICAL DIMENSIONS INCHES (MM) 1 MODEL t 1.1 MAX. 28,0) I NUMBER 0.190 MAX. ,-----,~ r---r x =0.150 MIN. (3,8) 0.010 0.018 KOVAR Pins 1'. 1711 I I I. BOTTOM VIEW I SP~~ES 1.7l:a~:X' I AIOU'00 (2,5) 321.-L NOTE: Pins have 0.025 Inch fO.01 s1andofffromcsae. 1-34 ORDERING INFORMATION ADS-132MC ADS-132MM OPERATING TEMP. RANGE o°c to +70 °C -55 °C to +125 °C SEAL Hermetic Hermetic Receptacle for PC board mounting can be ordered through AMP Inc., Part #3-331272-8 (Component Lead Socket), 24 required. ADS-EVAL1 Evaluation Board (without ADS-132) For availability of MIL-STD-883 versions, contact DATEL. DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194fTEL (508) 339-3000fTLX 174388/FAX (508) 339-6356 ADS-193 12-Bit, 1.0 MHz, Low-Power Sampling AID Converter FEATURES • • • • • • 12-Bit resolution Internal Sample/Hold 1.0 MHz minimum throughput Functionally complete Low-power, 1.3 Watts Samples to Nyquist INPUT/OUTPUT CONNECTIONS GENERAL DESCRIPTION PIN DATEL's ADS-193 is a 12-bit, functionally complete, sampling AID converter that is packaged in a 40-pin ceramic DIP. A minimum throughput rate of 1.0 MHz is achieved while only dissipating 1.3 Watts. The ADS-193 digitizes signals up to Nyquist. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Typical applications include spectrum, transient, vibration and waveform analysis. This device is also ideally suited for radar, sonar, video digitization, medical instrumentation and highspeed data acquisition systems. For information on high reliability screening, contact DATEl. +10V REF FUNCTION PIN 40 +5V + 10 V REFERENCE DIGITAL GROUND DIGITAL GROUND ·15V ANALOG INPUT DO NOT CONNECT GAIN OFFSET ADJ. ANALOG GROUND ANALOG GROUND ANALOG GROUND ANALOG GROUND ANALOG GROUND ANALOG GROUND ANALOG GROUND ANALOG GROUND +5V DIGITAL GROUND -15V START CPNVERT 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 FUNCTION DIGITAL GROUND BIT lOUT (MSB) BIT 2 OUT BIT30UT BIT 4 OUT BIT 5 OUT BIT60UT +5V UNIPOLAR OFFSET +10V REFERENCE +15V BIT70UT NO CONNECTION NO CONNECTION BIT 8 OUT BIT 9 OUT BIT 10 OUT BITll OUT .!!JL12 OUT (LSB) EOC 2.llf-------l-l-----I 39 BIT 1 (MSB) 38 BIT2 37 BIT 3 36 BIT4 35 BIT 5 GAIN & OFFSET ADJ. DIGITAL CORRECTION LOGIC UNIPOLAR OFFSET 32 A~~~~~6J-__~---' 34 BIT 6 29 BIT 7 26 BIT8 25 BIT9 24 BIT 10 23 BIT 11 START CONY. 20 roc 21 LOGIC CONTROL AND TIMING 22 BIT 12 (LSB) ~~~~~~~~~~====:i::)~~~--J ~ +5V 3,4,18,40 DIG.GND. For Immediate Assistance, Dial 1-800-233-2765 +15V 9 THROUGH 16 ANAGND. 5,19 ·15V 1-35 ADS·193 ABSOLUTE MAXIMUM RATINGS PARAMETERS LIMITS UNITS +15V Supply (Pin 30) o to +18 -15V Supply (Pin 5,19) +5V Supply (Pin 1,33) Oto -18 -0.5 to +7.0 Volts dc Voltsdc Voltsdc Digital Inputs (Pins 20) Analog Input (Pin 6) Lead Temp. (10 Sec.) -0.3 to +6.0 -15to+15 300 max Voltsdc Volts de °C FUNCTIONAL SPECIFICATIONS Apply over the operating temperature range and at ±15V de and +5V de unless otherwise specified .. ANALOG INPUTS Input Voltage Range MIN. TYP. MAX. UNITS - Oto·5 ±2.5 1,000 6 - Voltsdc Voltsdc Ohms pi - Input Impedance Input capacitance 950 - - 1,050 15 DIGITAL INPUTS Logic Levels logic "1" logic "0" logic loading "1" logic loading "0" - AID PERFORMANCE No Missing Codes (12 Bits; lln=500 KHz) Integral Non-linearity +25°C oOCto +70 °C ·55C to +125 °C Differential Non·Linearity +25°C o°C to +70 °C -55 C to +125 °C Full Scale Absolute Accuracy +25°C oOCto +70 °C -55 Cto+125 °C Unipolar Zero Error, +25 °C (See Tech Note 1) Unipolar Zero Tempco Bipolar Zero Error, +25 °C (See Tech Note 1) Bipolar Zero Tempcc Bipolar Offset Error, +25 °C (See Tech Note 1) Bipolar OHset Tempcc Gain Error, +25 °C (See Tech Note 1) Gain Tempco logic Levels logic "1" logic "0" logic loading "I" logic loading "0" Internal Reference Voltage, +25 °C Drift. External Current 1·36 - 2.0 - 0.8 5.0 ·200 Volts de Voltsdc j.IA j.IA Over the Operating Temp. Range. - - - ±1/4 ±1/4 - ±3/4 ±3/4 ±1.5 lSB lSB lSB - ±3/4 ±314 ±1 lSB lSB lSB ±O.13 ±O.15 ±0.25 ±O.25 ±O.44 ±0.78 %FSR %FSR %FSR ±O.074 ±15 ±O.13 ±30 %FSR ppm! ° C ±O.074 ±5 ±O.13 ±8 %FSR ppm/oC ±O.1 ±20 ±O.1 ±O.2 ±40 ±O.2 %FSR ppm! ° C %FSR - ±20 ±40 ppm! ° C 2.4 - 0.4 -160 4.8 - Vonsdc Voltsdc j.IA rnA +10.02 ±30 1.5 Voltsdc ppm! ° C mA - +9.98 - - +10.0 ±5 - ANALOG INPUTS MIN. TYP. Resolution Output Coding MAX. UNITS 12 Bits Complementary binary Complementary offset binary PERFORMANCE Conversion Rate In·Band Harmonics (-o.5dB) DC to 100KHz 100 KHz to 500 KHz Total Harm. Distort. (·0.5dB) DC to 100KHz 100 KHz to 500 KHz Signel·to-Nolse Ratio (w/o distortion, -o.5dB) DC to 100KHz 100KHz to SOO KHz Signel·to-Nolse Ratlo & distortion, -o.5dB DC to 100 KHz 100KHz to 500 KHz Effective Bits, -o.5dB De to 100 KHz 100 KHz to SOO KHz Two-Tone Intermodulatlon Distortion (fIN=75, 105 KHz Fs=1 MHz, ·7dB Two-Tone Intermodulation DiS!. (fIN=480 KHz, 490 KHz, Fs=1 MHz, (-O.5dB) Input Bandwtdth Small Signal (·2OdB) Full Power (OdB) Slew Rate Aperture Delay Time Effect. Aperture Delay Time Aperture Uncertainty (Jitter) (rms) (peak) SlH Acquisition lime to 0.01% (Transient Recovery) Overvoltage Recovery Time 1.0 ·78 ·73 - ·76 ·70 -81 ·75 ·75 FS-dB FS-dB -87 ·72 ·71 - FS-dB FS-dB -86 -86 ·70 ·70 FS-dB FS-dB 11.0 10.6 11.25 11.0 - ·80 -88 - FS-dB ·65 ·68 FS-dB 7.5 5 10 8 150 - V1!1Sec. 20 16 nSec. nSec. ±15 ±SO pSec. pSec. -68 -68 - - - MHz FS-dB FS-dB Bits Bits MHz MHz - - - - 160 1000 nSec. nSec. +14.25 ·14.25 +4.75 +15.0 ·15.0 +5.0 +15.75 ·15.75 +5.25 Volts de Voltsdc Volts de - +24 +35 -48 +115 1.7 0.05 mA mA mA Watts %FSRI%V a - +70 +125 ° C ° C +ISO ° C - - - - POWER REQUIREMENTS Power Supply Range +15V de Supply ·15V dc Supply +5V dc Supply Power Supply Current +15V dc Supply ·15V dc Supply +5V dc Supply (l) Power Dissipation Power Supply Rejection - ·40 +95 1.3 - PHYSICAUENVIRONMENTAL Operating Temp. Range ·MC ·MM Storage Temperature Range Package Type Weight (l) ·55 -85 - 4O·pin hermetic sealed, ceramic DIP 0.56 ounces (16 grams), maximum +5V power usage at 1 TTL logic loading per data output bit. Specifications subject to change without notice. DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048·1194rrEL (508) 339·3000rrLX 174388/FAX (508) 339-6356 ADS·193 TECHNICAL NOTES 1. Use external potentiometers as shown in Figure 3 to adjust the offset and gain errors to zero. For operation without adjustment, leave pin 8 open. For bipolar operation, adjust the potentiometer such that the code flickers equally between 1000 0000 0000 and 1000 00000001. 2. Rated performance requires using good high-frequency circuit board layout techniques. The analog and digital grounds are connected internally. Avoid ground-related problems by connecting the digital analog grounds to one point, the ground plane beneath the converter. 3. Full-Scale Adjustment Set the output of the voltage reference used in step 2 to the value shown in Table 2. Adjust the gain trimming potentiometer so that the output code flickers equally between 1111 11111110and 111111111111. Due to the inductance and resistance of the power supply return paths, return the analog and digital ground separately to the power supplies. 4. To confirm proper operation of the device, vary the preCision reference voltage source to obtain the output coding listed in Table 3. 3. Bypass the analog and digital supplies to ground with a 10 j.1F, 2SV tantalum electrolytic capacitor. Bypass the +10V reference (pin 2 and 31) to analog ground (pin 16) with a 0.1 j.1F ceramic capacitor. Table 2. Zero and Gain Adjust FSR 4. For unipolar, 0 to -SV FSR, connect pins 31 and 32. For bipolar, ±2.SV FSR, connect pin 32 to analog ground and connect pin 31 to a 0.1 j.1F ceramic capacitor only. ZERO ADJUST + 1/2 LSB Oto -SV dc ±2.SVdc -0.61mVdc +0.61 mV GAIN ADJUST +FS - 1 1/2 LSB -4.9982V -2.4982V S. Pins 27 and 28 are no connection pins. Connecting pins 27 and 28 together is acceptable. tsc - 200 nS mlnJ750 nS max. TIMING START CONVERT Figure 2 shows the relationship between the various input signals. The timing shown applies over the operating temperature range and over the operating power supply range. These times are guaranteed by design. tsp -1000 nS min ~12ns HOLD PULSE (INTERNAL) CALIBRATION PROCEDURE 40 nS =-=L:=J tCONV - 850 nS Max. 1. Connect the converter per Figure 3 for the appropriate fullscale range (FSR). Apply a pulse of 200 nanoseconds minimum to the START CONVERT input (pin 20) at a rate of 2S0 KHz. This rate is chosen to reduce flicker if LED's are used on the outputs for calibration purposes. EOC --I ~tDC"5""Max OUTPUT DATA 2. Zero Adjustments Apply a precision voltage reference source between the amplifier's analog input and ground. Adjust the output of the reference source per Table 2. Adjust the zero trimming potentiometer so that the output code flickers equally between 0000 0000 0000 and 0000 0000 0001 for unipolar. KI>V Cb V 31' «>V C· V Cb V 32 33 Cb V ca V Cb DO NOT CONNECT 30 V -15V Cb h~,,-+10VREF. 17 «>V +15V 612 19 V 27 NO CONNECTION 28 NO CONNECTION 910 16 DIGITAL GROUND ANALOG GROUND *For unipolar operation. connect pins 31 and 32. For bipolar operation, ground pin-52 and connect a 0.01 ~f capacitor between pin 31 and ground. ea - is 10 J.Lf tantalum Cb - is 0.1 J,lF ceramic Figure 3, Typical ADS-193 Connection Diagram .B ·10 ·20 -30 "0 ·5• ... ·70 ,. ·so . • .u. : ·100 50 1 so 1 00 200 ..,ld~J .1" 250 300 350 400 450 500 KHz FFT Analysis of ADS-193 MECHANICAL DIMENSIONS INCHES (MM) 1.1 Max. I_ O,':,?,.) 1, T U ORDERING INFORMATION oil (28.0) I U T 0.200 (5.0) Max T '0.010 xO.t60(4.1) KOVAR T I s:m 1 :! 1 20 211 ADS-193 20 Plns 0,'0" Aport (2,5) :I :1 MODEL NUMBER OPERATING TEMP. RANGE SEAL ADS-193MC ADS-193MM ADS-EVAL1 o °C to +70 °C Hermetic -55°C to + 125 °C Hermetic Evolution Board (without ADS-193) 2.12MBx. Receptacle for PC board mounting can be ordered through AMP Inc., Part # 3-331272-8 (Component Lead Socket), 40 required. 40 j:;o;:O·=90=(..=~~);j-:j'l 0.100 For availability of MIL-STD-88g versions, contact DATEL. (2,5) 1-38 DATEL, Inc. 11 Cabot· Boulevard, Mansfield, MA 02048-1194fTEL (508) 339-3000fTLX 174388/FAX (508) 339-6356 ADS-21PC Low-Power, 12-Bit, 1.3 MHz Sampling AID Converter FEATURES • • 12-81t resolution 1.3 MHz throughput rate S/H included • Single 46-pin DIP GENERAL DESCRIPTION DATEL's ADS-21 PC Sampling Converter combines a 12-bit AID and a S/H in one space-saving package. Designed and manufactured at DATEL's modern, certified hybrid assembly facility using state-of-the-art integrated circuits, the ADS-21 PC provides the highest quality and performance for signal processing applications. TECHNICAL NOTES 1. Use external potentiometers to remove system errors or the small initial errors to zero. Use a 20K trimming potentiometer for gain adjustment with the wiper tied to pin 36 (ground pin 36 for operation without adjustments). Use a 20K trimming potentiometer with the wiper tied to pin 37 for zer%ffset adjustment (leave pin 37 open for operation without adjustment). 0.300 (7,62) MAX. -*- MECHANICAL DIMENSIONS 0 - ,- T - - - - '-n.r-------rr" U u1.300 -(33,02)-1 -1 2. Rated performance requires using good high frequency circuit board layout techniques. The analog and digital grounds are connected internally. Avoid ground-related problems by connecting the digital and analog grounds to one point, the. ground plane beneath the converter. Due to the inductance and resistance of the power supply return paths, return the', analog and digital ground separately to the power supplies. This prevents contamination of the analog ground by noisy digital ground currents. INCHES (mm) 1 " t 0.150 (3,81) MIN. =-1 _t_ (2,5) 2.620 (66,6) MAX. BOTTOM -t- VIEW 22 SPACES AT 0.100@±O.005 NON-CUMULATIVE J 1- 1.620 _ _ (41.2) -+ I PIN DIAM. = 0.020 (0.51) MAX. +10Vdc NO CONNECTIONS 1,8,11,32,35,42,46 REF OUT SIH OUT RANGE 43 44 40 INPUT/OUTPUT CONNECTIONS ENABLE 10 34 COMP BIN OFFSET OVERFLOW ADJUST3? 12 BIT 1 (MSB) BIAS 38' INPUT 39 13 BIT2 14 BIT 3 I-'VVI.....-.-i 15 BIT 4 16 BIT 5 GAIN 1? BIT 6 ADJUST 36 18 BIT? 19 BIT 8 START 20 BIT 9 CONVERT 21 BIT 10 22 BIT11 23 BIT 12 (LSB) 6 24,30,41 2,4,5, ? ANALOG DIGITAL GROUNDS GROUNDS 9 31 45 +5Vdc +15V de -15Vde For Immediate Assistance, Dial 1-800-233-2765 EOC PIN FUNCTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 NlC DIG GND START CONVERT DIG GND DIG GND EOC DIG GND N/C ~ ENABLE N/C BIT 1 (MSB) BIT 2 BIT 3 BIT 4 BIT 5 BIT 6 BIT 7 BIT 8 BIT 9 BIT10 BIT11 BIT 12 (lSB) PIN 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 FUNCTION ANAGND ANAGND ANAGND ANAGND ANAGND ANAGND ANAGND +15V N/C OVERFLOW CoMPsiN NlC GAIN ADJUST OFFSET ADJUST BIAS ANALOG INPUT RANGE ANAGND NIC +10V REF OUT SIH OUT -15V NlC 1-39 ADS·21.PC ABSOLUTE MAXIMUM RATINGS DYNAMIC PERFORM. CONT. PARAMETERS LIMITS +15V Supply (Pin 31) -15V Supply (Pin 45) +5V Supply (Pin 9) Digital Inputs (Pins 3,10,34) Analog Input (Pins 38, 39) Lead Temp. (10 Sec.) -0.3 to +18V dc +0.3 to -18V dc -0.5 to +7V dc -0.3 to +5.5V dc -15 to +15V dc 300°C FUNCTIONAL SPECIFICATIONS Apply over the operating temperature range and at ±15V dc and +5V dc unless otherwise specified. INPUTS Input Voltage Ranges Input Impedance o to -10V, 0 to +10V, ±10V Oto -5V, ±5V Logic Levels Logic 1 Logic 0 Logic Levels Logic 1 Logic 0 MIN. TYP. MAX. - - Oto +10 Oto -5V Oto-l0 ±io, ±5 - - Vdc Vdc Vdc Vdc - 1 500 - KQ Ohms 2.0 - 0.8 Vdc Vdc 5 -200 IlA IlA - - - UNITS OUTPUTS Output Coding Options Logic Levels Logic 1 Logic 0 Logic Loading Logic 1 Logic 0 Internal Reference (Pin 43) Voltage, +25 °C Drift External Current (Pin 43) straight binary offset binary complementary binary complementary offset binary - - - - 2.4 - 9.98 - 0.4 Vdc Vdc -160 6.4 I'A mA Vdc ppm/oC mA - 10.0 ±5 - - 10,02 ±30 1,5 - -74 - dB -69,0 -67 -71 -70 - dB dB -68,0 -66 -71 -70 - dB dB 11 10,7 11,5 11,3 - Bits Bits -72 -70 ·80 ·75 - 16 300 - - ±16 ±50 - 60 100 1-40 TYP MAX UNITS 145 165 180 220 nS nS PERFORMANCE, ±10V RANGE Integral Nonlinearity Oto +70 °C Differential Nonlinearity Oto +70 °C FS Absol. Accuracy +25°C Oto +70 °C Unipolar Zero Error +25°C Unipolar Zero Tempco Bipolar Zero Error Bipolar Zero Tempco Bipolar Offset Error +25°C Bipolar Offset Tempco Gain Error, +25 °C Gain Tempco Throughput Rate +25 °C oto +70 °C No Missing Codes (12 bits) ±0,0125 %FSR±1I2LSB ±Q,0125 %FSR±1/2LSB ±5 ±6 ±12 ±15 LSB LSB ±2 ±13 ±5 ±25 ±5 ±25 LSB ppm/oC LSB ppm/oC ±8 ±40 ±8 ±40 LSB ppm/oC LSB ppm/oC ±13 ±2 ±17 ±3 ±18 1.3 MHz 1.1 MHz Over the operating temp. range, POWER SUPPLY REQUIREMENTS Power Supply Range +15V dc Supply -15V dc Supply +5V dc Supply Power Supply Current + 15V Supply -15V Supply +5V Supply' Power Dissipation Power Supply Rejection +14,25 -14,25 +4.75 +15 -15 +5 +50 -65 +80 2.1 0,01 +15.75 V dc -15,75 Vdc +5,25 V dc +65 -72 +95 2,5 0,05 mA mA mA Watts "IoFSR/"IoV PHYSICAL-ENVIRONMENTAL Operating Temp. Range Storage Temp. Range Package Type Pins Weight o -65 • +5V power usage at 1 TTL logic loading per data output bit. DYNAMIC PERFORMANCE Feedthrough Rejection SNR w/o distortion, -0.5 dB dc to 100 kHz 100 KHz to 500 KHz SNR with distortion, ..(l.5 dB dct:> 100 kHz 100 KHz to 500 KHz Effective Bits dcto 100 kHz 100 KHz to 500 KHz Inband Harmonics (j) dcto 100 KHz 100 to 500 KHz Frequency Response Small Signal (·3 dB) Slew Rate Aperture Delay Time Aperture Uncertainty (Jitter) Settling Time 10V to ±0,01% FS (±lmV) MIN Acquisition Time 10V step to ±1.0 mV (0,01% FS) +25°C Oto +70 °C - - FS-dB FS,-dB MHz VII'S nS pS nS Same specification values apply for Total Harmonic Distortion (-0.5 dB below FS), (j) TECHNICAL NOTES CaNT. 3, Bypass all the analog and digital supplies and the + 1OV reference (pin 43) to ground with a 4.7I1F, 25V tantalum electrolytic capacitor in parallel with a 0.1 I1F ceramic capacitor. Bypass the +1 OV reference (pin 43) to analog ground (pin 41). 4. The COMP BIN input (pin 34) allows selection of binary/ offset binary or complementary binary/complementary offset binary. Refer to Table 3 for the desired coding selection. Pin 34 has an internal pull-up resistor and is TTL-compatible for those users desiring logic control of this function. 5, The internal Sample/Hold control signal goes low following the rising edge of a start convert pulse and hiQ.,h 65 nanoseconds minimum before EOC goes low. This S/H low signal indicates that the converter can accept a new analog input. DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194ITEL (508) 339-3000ITLX 174388/FAX (508) 339-6356 ADS·21PC Table 1. Input Connections Table 2. Zero and Gain Adjust Input Voltage Range Connect Input Pin 38 to Connect Pin 40 (Range) to Oto-5V Oto-10V to +10V ±5V ±10V 39 44 44 44 43 43 a Ext. -10V Ref: 39 - FSR Zero Adjust +1/2 LSB Gain Adjust +FS -1 1/2 LSB Oto-5V Oto-10V a to +10V ±10Vdc ±5Vdc -0.61 mV -1.22mV +1.22 mV +2.44 mV +1.22 mV -4.9982V -9.9963V +9.9963V +9.9927V dc +4.9963V dc "May be referenced to +1 OV Ref. (Pin 43) CALIBRATION PROCEDURE 1. Connect the converter per Figure 3 and Tables 1 and 3 for the appropriate full-scale range (FSR) and coding options. Apply a pulse of 100 nanoseconds minimum to the START CONVERT input (pin 3) at a rate of 500 KHz. This rate chosen to reduce flicker if LED's are used on the outputs for calibration purposes. For bipolar operation, adjust the potentiometer until the displayed code flickers equally between 1000 0000 0000 and 100000000001 orbetween011111111111 and01111111 1110. Refer to Table 5. 3. Full-Scale Adjustment Set the output of the voltage reference used in step 2 to the value shown in Table 2. Adjust the gain trimming potentiometer so that the output code flickers equally between 1111 1111 1110 and 1111 1111 1111 or between 0000 0000 0001 and 0000 0000 0000 depending on the output coding selected. 2. Zero Adjustment Apply a preCision voltage reference source between the analog input (pin 39) and ground (pin 24). Adjust the output of the reference source per Table 2. For Unipolar operation adjust the zero trimming potentiometer so that the output code flickers equally between 0000 0000 0000 and 0000 0000 0001 or between 1111 1111 111t and 1111 1111 1110. Refer to Table 4. ANALOG INPUT 4. To confirm proper operation of the device, vary the precision reference voltage source to obtain the output coding listed in Tables 4 and 5. ~-------------------1 I ---, START CONVERT - - - '00 nSec HOLD MODE SETTLING TIME N~L ---::-1--' L 1 10 nSec MIN. 25 nSec MAX. 100nSecMIN. T1 Values ~L-_-L....I--+-,11 1 INTERNAL Sl H ~~·I -11---15nsecMIN. 20 nSec MAX. _~ I 65nSec MIN. Temperature +25 °C 0 to +70 °C Conversion Time L_ I 1 TIME OUTPUT DATA ~I 1 1 _ _ T' MAXIMUM 350 nSec MIN. -I ---I r-- t>
-1 1 BIT 14 OUT (LSB) EOC 15 13 14 22 23 24 +5V DIG.GND. +15V GND. ·15V For Immediate Assistance, Dial 1-800-233-2765 1-43 ADS·924 ABSOLUTE MAXIMUM RATINGS PARAMETERS LIMITS +15V Supply (Pin 22) -15V Supply (Pin 24) +5V Supply (Pin 13) o o Digital Inputs (Pins 14, 16) Analog Input (Pin 19) Lead Temp.(10 Sec.) UNITS OUTPUTS to +18 to -18 -0.5 to +7.0 Volts de Volts de Volts de 'No Missing Codes (14 Bits) (13 Bits) (12 Bits) -0.3 to +6.0 -15to+15 300 max Volts de Volts de °C Logic Levels Logic "1" Logic "0" Logic Loading "1" Logic Loading "0" Internal Reference Voltage, +25 °C Drift External Current FUNCTIONAL SPECIFICATIONS Apply over the operating temperature range and at ±15V de and +5V de unless otherwise specified. Resolution Output Coding ANALOG INPUTS DYNAMIC PERFORMANCE Input Voltage Range ADS-924 (See Table 4 also) Input Impedance Input Capacitance MIN. TYP. MAX. UNITS - ±5 010+10 15.0 3 - Vollsdc Vollsdc MOhms pi 2.0 - - Volts de Vollsdc 5.0 5 DIGITAL INPUTS Logic Levels Logic "1" Logic "0" Logic Loading ·'1" Logic Loading "0" - - PERFORMANCE Integral Non-Linearity +25 °C (see Tech Noles) o °Clo +70 'C -55 'C 10 +125 °C Differential Non·Unearity +25°C o °Clo+70 °C -55°C 10 +125 °C Full Scale Absolute Accuracy +25°C o °Clo +70 °C -55°C 10 +125 °C Unipolar Zero Error, +25 °C (See Tech Note 1) o °C'lo +70 °C -55°C 10 + 125 °C Bipolar Zero Error, +25 °C (See Tech Nole 1) o °C 10 +70 °C -55°C 10 + 125 °C Bipolar Offset Error, +25 °C (See Tech Note 1) o °C 10 +70 °C -55°C 10 +125 °C Gain Error, +25 °C (See Tech Nole 1) o °C 10 +70 °C -55°C 10 +125 °C - - - - ±1/2 ±1 ±1/2 ±1 - 0.8 5 -200 IIA IIA ±1 ±2 ±3 LSB LSB LSB ±1 ±2 ±2.5 LSB LSB LSB MIN. TYP. MAX. UNITS al +25 °C over 0 to 70°C temp. range over -55 to +125 °C temp. range - 2.4 - - +9,98 - - - 0.4 -160 6.4 +10.0 ±5 +10.02 ±30 1.5 - Volts de Voitsdc j.iA mA Volts dc ppm/oC mA 14 Bits Straight binary/offset binary Conversion Time +25°C 300 °C to +70 °C 300 -55°C to +125 °C 300 Total Harmonic Distortion DC to 100 KHz at Vin<2.5V pop -72 +25°C -55°C to +125 °C -70 DC to 40 KHz at Vin = 10V pop -72 +25°C -55°C to +125 °C -70 Slew Rate Aperture Delay Time Aperture Uncertainty S/H Acquisition Time to 0.006% (10V step) +25°C O°Cto +70 °C -55°C to +125 °C (Sinusoidal Input) - o - - KHz KHz KHz -76 -72 - dB dB -76 -72 90 20 ±100 - dB dB VlJ,LSec. nSee. pSec. - 1.2 1.35 1.5 700 I1Sec. J,LSee. I1See. nSee. +15.0 -15.0 +5.0 +15.75 -15.75 +5.5 Volts de Volts de Voitsde - +41 -46 +66 1.4 - - +49 -53 +75 1.8 0.Q1 mA mA mA Watts %FSR/% 0 -55 - +70 +125 °C °C +150 °C POWER REQUIREMENTS - - ±0.037 ±0.074 ±0.12 ±0.074 ±0.13 ±0.2 %FSR %FSR %FSR ±0.02 ±0.031 ±0.09 ±0.12 %FSR %FSR %FSR ±0.031 ±0.09 ±0.12 %FSR %FSR %FSR ±0.061 ±0.12 ±0.15 ±0.061 %FSR %FSR %FSR %FSR ±0.12 ±0.15 %FSR %FSR - - ±0.02 - ±0.02 - - - - - - ±0.02 - - Power Supply Range + 15V de Supply -15V de Supply +5V de Supply Power Supply Current + 15V de Supply -15V de Supply +5V de Supply· Power Dissipation Power Supply Rejection 14.25 14.25 +4.5 PHYSICAL/ENVIRONMENTAL Operating Temp. Range -MC -MM Storage Temperature Range Package Type Weight -65 24-pin hermetic sealed, ceramic DIP 0.42 ounces (12 grams) • +5V power usage at 1 TTL logic loading per data output bit. 1-44 DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194fTEL (508) 339-3000fTLX 174388/FAX (508) 339-6356 ADS·924 '. TECHNICAL NOTES Table 4. Input Ranges (using external calibration) 1. Applications which are unaffected by endpoint errors or remove them through software will use the typical connections shown in Figure 3. Remove system errors' or adjust tile small initial errors of the ADS-924 to zero using the options] external circuitry shown in Figure 4. The external adjustment circuit has no affect on the throughput rate. 2. Bypass the analog and digital supplies and the + 1OV ref.~r: ence (pin 21) to ground with a 4.7 !IF, 25V tantalum electro, lytic capacitor in parallel with a 0.1 !IF ceraJTlic capacitor. Bypass the + 1OV reference (pin 21) to analog ground (pin 23). INPUT RANGE R1 o to +10V, ±5V oto +5V, ±2.5V o to +2.5V, ±1.25V 2 1.65 715 0.1~F 0.1~F 22 23 24 13 23 W!L- 1 Figure 2 shows the relationship between the various input signals. The timing shown applies over the operating temperature range and over the operating power supply range. These times are guaranteed by design. START CONVERT 4.7~F ~ i Mn. I I ~---.---------------- L :... 9oon8_... 1 __I START CONVERT -:ro-,r-- 16 A05-924 20 BIPOLAR INPUT I~I NOTE: NOT DRAWN TO SCALE :1------------ ~I II -BIPOLAR - - OPERATION I I 700 ns ACQUISITION nME (SINUSOIDAL INPUT) " +5V 19 ANALOG INPUT TIMING ANALOG INPUT SETIUNG TIME -15V 4.7~F KOhms KOhms K'Ohms + 4. To obtain three-state outputs, connect ENABLE (pin 14) to a logic "0" (low). Otherwise, connect ENABLE (pin 14) to a logic "1" (high). INPUT UNIT 2 4.99 4990 +15V 3. The ADS-924 exhibits up to 2.0 LSB's of peak-to-peak noise. Digital signal processing (DSP) applications will average this n o i s e . ' ANALOG R2 21 IV "[l.1~F L ___ +10 REF ' -_ _ _ _ _ _ _ _...r- ENABLE BIT 1 (MSB) BIT2 BIT 3 BIT 4 BITS BIT 6 BIT 7 BITS BIT9 BIT 10 BIT 11 BIT 12 BIT 13 BIT 14 ...1 UNIPOLAR OPERATION Figure 3. Typical Input Connections for the ADS-924 ONTERNAL) SlH OUTPUT I I. , 181 1 I ~ 3.13~S"n. - I .. I 2OnSMax. I OATA INVAUO OATA ENABLE ENABLED DATrA'--_ _ _-;n;;ou;;-:;~, ~I- N·1VAUD I ENABLED DATA 10nSMax._II+-N.,VAlID Figure 2. ADS-924 Timing Diagram Table 2. Input Range Selection INPUT RANGE ±5Vdc o to +10V dc INPUT PIN Pin 19 Pin 19 TIE TOGETHER Pin 20 to Pin 21 Pin 20 to Ground Table 3. Zero and Gain Adjust FSR oto +10V dc ±5Vdc ZERO ADJUST +1/2 LSB +300!lV dc +300!lV dc GAIN ADJUST +FS -11/2 LSB +9.9991 V dc +4.9991V dc For Immediate Assistance, Dial 1-800-233-2765 CALIBRATION PROCEDURE 1. Connect the converter per Figure 3, Figure 4, and Table 2 for the appropriate. full-scale range (FSR). Apply a pulse of 200 nanoseconds minimum.to the START CONVERT input (pin 16) at a rate of 250 KHz. This rate is chosen to reduce flicker if LED's are used on the outputs for calibration purposes. 2. Zero Adjustments Apply a precision voltage reference source between the amplifier's analog input and ground. Adjust the output of the reference source per Table 3. For unipolar, adjust the zero trimming potentiometer so that the output code flickers equally between 00 0000 0000 0000 and 00 0000 0000 0001. For bipolar operation, adjust the potentiometer such that the code flickers equally between 10 0000 0000 0000 and 10 000000000001. 1-45 ADS-924 3. Full-Scale Adjustment Set the output of the voltage reference used in step 2 to the value shown in Table 3. Adjust the gain trimming potentiOmeter so that the output code flickers equally between 11 111111111110and 11111111111111. 4. To confirm proper operation of the device, vary the precision reference voltage source to obtain the output coding listed in TableS. Table 6. Output Coding STRAIGHT Oto +10V +9.99939V +8.7500V +7.5000V +5.0000V +2.5000V +1.2500V +0.0003V O.OOOOV SCALE +FS -1 LSB 7/8 FS 3/4 FS 1/2 FS 1/4 FS 1/8 FS 1 LSB 0 BIN CaMP BINARY OUTPUT CODING INPUT 'RANGE UNIPOLAR MSB LSB 111111111111' 1110 0000 0000 1100 0000 0000 1000 0000 0000 0100 0000 0000 0010 0000 0000 000000000001 0000 0000 0000 OFF BINARY BIPOLAR MSB LSB 0000 0000 0000 0001 1111 1111 0011 1111 1111 0111 1111 1111 101111111111 1101 1111 1111 111111111110 111111111111 CaMP OFF SCALE +FS-HSB +3/4 FS +1/2 FS 0 -1/2 FS -3/4 FS -FS + 1 LSB -FS INPUT RANGES +4.99939V' +3.7500V +2.5000V O.OOOOV -2.5000V -3.7500V -4.99939V -5.0000V BIN dB Or--------.------------------------, 20 40 R2* 60 +15V SIGNAL INPUT Figure 5. FFT Analysis of AD5-924 ZERO/OFFSET ADJUST MECHANICAL DIMENSIONS INCHES (MM) I· 0.800MAX 0.190 MAX ~ 0.010 X 0.018 ~ KOVAR Pins 13 1'2 1 1 1 1 1 1 1 1 BOTTOM 1 1 VIEW 1 1 1 1 1 1 1 1 ! 1 1-46 * See Table 4 for R1 and R2 values. ., (20,3) 1 24 0.600 • (15,2) 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 ! ~ ==r 0.150 MIN. (3,8) TI 11 SPACES AT 0.100 Figure 4. Optional Calibration Circuit 1.310MAK (33,3) (2,5) ~ NOTE: Pins have a 0.025 inch, ±0.01 sland-off from case. ORDERING INFORMATION MODEL NUMBER ·ADS-924MC ADS-924MM OPERATING TEMP. RANGE o OCto +70 °c -55°C to +125 °c SEAL Hermetic Hermetic Receptacle for PC board mounting can be ordered through AMP Inc., Part # 3-331272-8 (Component Lead Socket), 24 required. For availability of MIL-STD-883B versions, contact DATEL. DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194ITEL (508) 339-3000ITLX 174388/FAX (508) 339-6356 ADS-928 High Resolution Sampling AID Converter FEATURES • • • • • • • 14-Bit resolution 500 KHz sampling rate Functionally complete Small 32-pin DIP Low-power,3.1 Watts Three-state output buffers Samples up to Nyquist INPUT/OUTPUT CONNECTIONS GENERAL DESCRIPTION PIN DATEL's ADS·928 is a 14·bit, 500 KHz sampling rate, function· ally complete AID converter. The ADS-928 samples up to Nyquist with no missing codes. FUNCTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Packaged in a small 32-pin DIP, power requirements are ±15 volts and +5 volts with 3.1 Watts power dissipation. +10V REF. OUT BIPOLAR ANALOG INPUT SIGNAL GROUND OFFSET ADJUST GAIN ADJUST OVERFLOW COMPo BIN ENABLE +5V DIGITAL GROUND +15V -15V NO CONNECTION ANALOG GROUND EOC PIN 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 FUNCTION BIT 14 OUT (LSB) BIT 130UT BIT 120UT BIT 11 OUT BIT 10 OUT BIT90UT BIT80UT BIT 7 OUT BIT 6 OUT BIT 5 OUT BIT40UT BIT 3 OUT BIT20UT BIT lOUT (MSB) BIT lOUT (MSB) START CONVERT GAIN ADJUST 6 1 - - - = = - - + - 1 - - - - - - - - , +10V REF 1 t--:::=--+-I-----~ 31 BIT lOUT (MSB) 30 BIT lOUT (MSB) OFFSET ADJUST 29 BIT 20UT 28 BIT 30UT 5 27BIT 40UT BIPOLAR 2 .........,Aero- 26BIT 50UT ANALOG INPUT 3 NIC 14 24 BIT 70UT 23 BIT 80UT LOGIC CONTROL START CONV.32 EOC 25 BIT 60UT DIGITAL CORRECTION LOGIC 19 BIT 12 OUT 18 BIT 13 OUT T~~~G L-..""'""T""r-r-J 17 BIT 14 OUT (LSB) 16t~=L=~~~~~~~~~~~;;~~~~~===~===Jl~=j 4 10 11 12 15 13 SIGNAL GND +5V DIG. GND. +15V ANA. GND. ·15V For Immediate Assistance, Dial 1-800-233-2765 7 OVERFLOW 9ENABLE 1-47 ADS-928 ABSOLUTE MAXIMUM RATINGS PARAMETERS LIMITS +15V Supply (Pin 12) -15V Supply (Pin 13) +5V Supply (Pin 10) UNITS -0.3 to +18 +0.3 to -18 -0.3 to +7.0 Digital Inputs (Pins 8, 9, 32) Analog Input (Pin 3) Lead Temp. (10 Sec.) Volts de Volts de Volts de -0.3 to +7.0 ±25 300 max Volts de Volts °C OUTPUTS Logic Levels Logic "1" Logic "0" Logic Loading "1" Logic Loading "0" Internal Reference Voltage, +25 °C Drift External Current MIN. TYP. 2.4 - MAX. UNITS - Volts dc Volts de - - 0.4 -160 6.4 +9.98 +10.0 ±13 - +10.02 ±30 2 -83 -78 -88 -82 - ., - FS-dB FS-dB -82 -78 -88 -84 - - FS-dB FS-dB -77 -72 -80 -75 - FS-dB FS-dB 12.5 12.0 13.2 12.3 - -92 - - FS-dB 6 1.75 - - MHz MHz - dB V/I!Sec. nSec. pSec. - I1A mA Voltsdc ppm/oC mA DYNAMIC PERFORMANCE FUNCTIONAL SPECIFICATIONS Apply over the operating temperature range and at ±15V dc and +5V de unless otherwise specified. ANALOG INPUTS Input Voltage Range MIN. TYP. MAX. UNITS - Oto-l0 ±5 5 7 - Volts Volts KOhms pI 2.0 - - Volts de Voltsdc - Input Impedance Input CapaCitance 4.9 15 DIGITAL INPUTS logic Levels Logic'l" Logic '0' Logic Loading '1" Logic Loading '0" - - - 0.8 5.0 -200 I1A I1A PERFORMANCE Inl. Non-Lin. @fiN = 250 KHz +25°C Oto+70°C -55 to +125 °C Dill. Non·Lin. @ fiN = 250 KHz +25°C Oto+70°C -55 to +125 °C Full Scale Absolute Accuracy +25°C. Oto+70°C -55to+125°C Unipolar Zero Error, +25°C o to +70 °C -55 to +125 °C Bipolar Zero Error, +25 °C (Tech Note 1) Oto +70 °C -55 to +125 °C Bipolar Offset Error, +25 °C (Tech Nole 1) Oto +70 °C -55 to+ 125°C Gain Error, +25 °C (See Tech Note I) 010 +70 °C -55to+125°C No MIssing Codes 14 Bits @ 250 KHz fiN 13 Bits@250 KHz fiN Resolution Outpul Coding (Pin8Hi) (Pin 8 Low) 1·48 - - - ±1/2 ±3I4 ±1 ±3/4 ±1 ±2 LSB LSB LSB - - - ±1/2 ±3I4 ±1 ±2 LSB LSB LSB - ±O.08 ±0.18 ±O.61 ±O.122 ±O.36 ±O.85 %FSR %FSR %FSR - ±O.04 ±O.07 ±O.1 ±O.122 ±O.13 ±O.17 %FSR %FSR %FSR - ±0.04 ±O.07 ±O.1 ±O.122 ±O.18 ±O.3 %FSR %FSR %FSR ±O.018 ±O.12 ±O.53 ±O.018 ±O'12 ±O.3 ±O.73 ±O.12 %FSR %FSR %FSR %FSR ±O.12 ±O.53 ±O.3 ±O.73 %FSR %FSR - - - OVER 0 TO +70·C. OVER -55 TO +125-C 14 Bits minimum Total Harm. Distort. (·0.5 dB) DC to 100 KHz 100 KHz to 250 KHz Signal·lo-Noise Ratio (w/o distortion, -0_5 dB) DC to 100 KHz 100KHz to 250 KHz Signal·lo-Noise Ratio & distortion, -0.5 dB DC to 100 KHz 100 KHz to 250 KHz Effective Bits, ·0.5 dB DC to 100 KHz 100 KHz to 250 KHz Two·tone Inlermodulatlon Distortion (fiN =100 KHz, 240 KHz, Fs=500 KHz, -0.5 dB) Input Bandwidth Small Signal (-20 dB input) Full Power (0 dB input) Feedthrough Rejection @fiN = 250 KHz Slew Rate Aperture Delay Time Aperture Uncertainty S/H Acquisition Time (to O_OI%FS (10V step) Overvollage Recovery, ±12V AID Conversion Rate +25·C 010+70'C -55 to = I 25'C POWER REQUIREMENTS Power Supply Range +15V de Supply -15V de Supply +5V dc Supply Power Supply Current +15V dc Supply -15V dc Supply +5V dc Supply (j) Power Dissipation Power Supply Rejection -90 80 - - Bits Bits - 90 ±20 - ±25 ±100 - 680 600 750 1000 ·nSec. nSec. 500 500 550 600 600 550 - - KHz KHz KHz +14.25 -14.25 +4.75 +15.0 -15.0 +5.0 +15.75 -15.75 +5.25 Volts de Volts de Volts de - +95 -88 +83 3.1 +115 -105 +100 3.4 0.02 mA mA mA Watts %FSR/%V 0 -55 - - +70 +125 °C °C - - PHYSICALJENVIRONMENTAL Operating Temp. Range ·MC ·MM Storage Temperature Range Package Type Weight (j) -65 +150 °C 32-pin hermetic sealed, ceramic TDIP 0.42 ounces (12 grams) +5V power usage at 1 TIL logic loading per data output bit. Straight binJoffset bin.l2's Camp. Comp. bin.lComp. offset bin., C2C DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048·1194fTEL (508) 339·3000fTLX 174388/FAX (508) 339·6356 ADS-928 TECHNICAL NOTES 1. Use external potentiometers to remove system errors or the small initial errors to zero. Use a 20K trimming potentiometer for gain adjustment with the wiper tied to pin 6 (ground pin 6 for operation without adjustments). Use a 20K trimming potentiometer with the wiper tied to pin 5 for zero/ offset adjustment (connect pin 5 to pin 15, analog ground for operation without adjustment). 2. Zero Adjustments Apply a precision voltage reference source between the analog input (pin 3) and signal ground (pin 4). Adjust the output of the reference source per Table 2. For unipolar, adjust the zero trimming potentiometer so that the output code flickers equally between 00 0000 0000 0000 and 00 0000 0000 0001 with the COMP BIN (pin 8) tied high (straight binary) or between 11 1111 1111 1111 and 11 1111 1111 1110 with the COMP BIN (pin 8) tied low (complementary binary). 2. Rated performance requires using good high-frequency circuit board layout techniques. The analog and digital grounds are not connected internally. Avoid ground-related problems by connecting the digital and analog grounds to one pOint, the ground plane beneath the converter. Due to the inductance and resistance of the power supply return paths, return the analog and digital ground separately to the power supplies. For bipolar operation, adjust the potentiometer such that the code flickers equally be1W.e.erL1.O 0000 0000 0000 and 10 0000 0000 0001 with COMP BIN (pin 8) tied high (offset binary) or between 01 1111 1111 1111 and 01 1111 1111 1110 with COMP BIN (pin 8) tied low (complementary offset binary). 3. Bypass the analog and digital supplies and the +10V reference (pin 1) to ground with a 4.7 ~F, 25V tantalum electrolytic capacitor in parallel with a 0.1 ~F ceramic capacitor. Bypass the +1 OV reference (pin 1) to analog ground (pin 15). 4. Obtain straight binary/offset binary output coding by tying COMP BIN (pin 8) to +5V dc or leaving it open. The device has an internal pull-up resistor on this pin. To obtain complementary bin~complementary offset binary output coding, tie the COMP BIN pin to ground. The COMP BIN Signal is compatible to CMOSITTL logic levels for those users desiring logic control of this function. Two's complement coding requires use of the MSB (pin 31) with COMP BIN (pin 8) tied high, adjusting the potentiometer such that the code flickers between 00 0000 0000 0000 and 00 0000 0000 0001. 3. Full-Scale Adjustment Set the output of the voltage reference used in step 2 to the value shown in Table 2. Adjust the gain trimming potentiometer so that the output code flickers equally between 11 1111 1111 1110 and 11 1111 1111 1111 for COMP BIN (pin 8) tied high (straight binary) or between 00 0000 0000 0000 and 00 0000 0000 0001 for COMP BIN tied low (complementary binary). 5. To enable the three-state outputs, connect ENABLE (pin 9) to a logic "0" (low). To disable, connect ENABLE (pin 9) to a logic "1" (high). Two's co!!!plement coding requires use of the MSB (pin 31) with the COMP BIN (pin 8) tied high, adjusting the gain trimming potentiometer so that the output code flickers equally between 01 1111 1111 1110 and 01 1111 1111 1111. 6. The 200 nSec. minimum START CONVERT pulse width assures the hold mode settling time requirements are met. 7. The specifications listed in Figure 2 (timing diagram) apply over the full operating temperature range unless otherwise specified. 4. To confirm proper operation of the device, vary the preCision reference voltage source to obtain the output coding listed in Table 3. CALIBRATION PROCEDURE 1. Connect the converter per Figure 3, and Table 1 for the appropriate full-scale range (FSR). Apply a pulse of 200 nanoseconds minimum to the START CONVERT input (pin 32) at a rate of 200 KHz. This rate is chosen to reduce flicker if LED's are used on the outputs for calibration purposes. ----.1 -+1 I START CONVERT 1_ HOLD MODE SETT1.ING I.L 200 nSec MIN -.,.---l\ N SIH ACa. TIME SIH OUT Table 1. Input Connections INPUT RANGE Oto -10V ±5V INPUT PIN Pin 3 Pin3 roc Pins 2 and 4 Pins 1 and 2 BUSY ~, OUT I TIE TOGETHER OUTPUT DATA +- 30 nSec MIN I SAMPLE 10 nSec MIN., 25 nSec MAX. (INTERNAL) AID _ HOlD CONTROL r"","-20nSecMIN.,35nSecMAX I I - - - 7OonSecMIN-_1 , DATA N-1 VALID 1><1 DATA N VALID INVALID -=1rrl<-:--,o-,S""'-',M""A""XD"'A-:CTA""N"'H""'BIT=E=-D-""'O'""'-:CS.-,M:7:AX:::-=_II4-·"::NABLEDDATANVAUD NOTE: NOT DRAWN TO SCALE Table 2. Zero and Gain Adjust FSR o to -10V ±5V ZERO ADJUST +1/2 LSB -305 ~V -305 ~V GAIN ADJUST FS -1/2 LSB -9.999085V -4.999085V For Immediate Assistance, Dial 1-800-233-2765 Note: Retriggering START CONVERT before EOC goes low will not start a new conversion. Figure 2. ADS-928 Timing Diagram 1-49 ADS-928 Table 3. Output Coding STRAIGHT UNIPOLAR INPUT RANGES, V de oto -10V SCALE FS -1 LSB 7/8 FS 314 FS 112 FS 1/4 FS 118 FS lLSB 0 -9.999390 -8.750000 -7.500000 -5.000000 -2.500000 -1.250000 -0.000610 0.000000 BIN COMP BINARY OUTPUT CODING MSB LSB IMSB LSB 11111111111111 00 0000 0000 0000 11 1000 0000 0000 00 0111 1111 1111 11 0000 0000 0000 00111111111111 10 0000 0000 0000 01 1111 1111 1111 01 0000 0000 0000 10111111111111 00 1000 0000 0000 11 0111 1111 1111 00 0000 0000 0001 11111111111110 00 0000 0000 0000 11111111111111 MSB LSB 01 1111 1111 1111 01 1000 0000 0000 01 0000 0000 0000 00 0000 0000 0000 10 0000 0000 0000 10 1000 0000 0000 10000000000001 10 00000000 0000 1_ 12 15 13 10 11 ~;...L.."";';...L......;.,-,-_,-,-_............, 9 GAIN ADJUST 31 30 29 010 -10V ----"-I +SVDC BIPOLAR SCALE +FS -1 LSB +3/4 FS +1/2 FS 0 -1/2 FS -3/4 FS -FS +1 LSB -FS MECHANICAL DIMENSIONS INCHES (MM) +5V ""-_"'---'-1 INPUT RANGE ±5Vde -4.99939 -3.75000 -2.50000 0.00000 +2.50000 +3.75000 +4.99939 +5.00000 +10V REF ANALOG INPUT COMP BIN START CONVERT NO CONNECTION ~0.010 X 0.018 ~ ENABLE 28 27 26 25 24 23 22 BIT 1 (MSB) BIT 1 (MSB) BIT 2 BIT3 BIT4 BITS BIT6 BIT 7 BIT 8 21 20 19 18 17 7 BIT 9 BIT 10 BIT 11 BIT12 BIT13 BIT 14 (LSB) L-SI_G_NAL_G_RO_U_N_D-r-:-_ _ _ _rl-6 20K -lSV +lSV ZEROIOFFSET ADJUST -I 1.101 MAX (28.0) ~~RFLOW KOVAR Pins 16 17 -, 15 SPACES ATO 100 (2,5) 1.712 MAX. (43,5) ll BOTTOM VIEW _I '---'-_ _.::320......... 1_ 0.900 (22,9) -I NOTE: Pins have a 0.025 inch, ±0.01 stand-off from case. Figure 3. Typical ADS-928 Connection Diagram dB ORDERING INFORMATION -10 -20 MODEL NUMBER -30 -40 ADS-928MC ADS-928MM ADS-EVALl -50 -60 -70 -80 -90 IIJ IJ -100 25 50 75 I 100 J J 115 I ,] 150 175 200 225 KHz - OPERATING TEMP. RANGE SEAL o°C to +70 °C Hermetic -55°C to + 125 °C Hermetic Evaluation Board (without ADS-928) Receptacle for PC board mounting can be ordered through AMP Inc., Part # 3-331272-8 (Component Lead Socket), 32 required. 250 For availibility of MIL-STD-883B versions, contact DATEL. Figure 4. FFT Analysis of ADS-928 1-50 DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194ITEL (508) 339-3000ITLX 174388/FAX (508) 339-6356 ADS-930 16-Bit, 500 KHz, High Resolution Sampling AID Converter ADVANCED PRODUCT DATA FEATURES 16-81t resolution 500 KHz sampling rate Functionally complete Internal StH Small 4D-pin DIP • Low-power,2.1 Watts Three-state output buffers • Samples up to Nyquist • 16 word FIFO memory I/O CONNECTIONS GENERAL DESCRIPTION Pin Function Pin Function DATEL's ADS-930 is a 16-bit, 500 KHz sampling rate, functionally complete AID converter with internal FIFO. The ADS930 samples up to Nyquist with no missing codes. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 Packaged in a small 40-pin TDIP, power requirements are ±15 Volts and +5 Volts with 2.1 Watts power dissipation. APPLICATIONS • • • • Spectroscopy Spectrum analysis Imaging Radar Medical instrumentation High-speed data acquisition systems +1OV REFERENCE BIPOLAR ANALOG INPUT ANALOG GROUND OFFSET ADJUST GAIN ADJUST +15V COMP BIN ENABLE FIFO READ ANALOG GROUND -15V ANALOG GROUND QY!;.RFLOW EOC +5V START CONVERT DIGITAL GROUND FSTAT1 FSTAT2 BIT 16 OUT (LSB) BIT 15..Q!JT FIFOtDIR DIGITAL GROUND BIT 14 OUT BIT 130UT BIT 120UT BIT 11 OUT BIT 10 OUT ANALOG GROUND BIT90UT BIT80UT BIT70UT BIT 6 OUT BIT50UT BIT40UT BIT30UT BIT20UT BIT 1 OUT (MSB) BIT 1 OUT (MSB) 1----;::::==;;;e======;--;:=~----_==========:I19 FSTAT1 , - - - - - - - - - - \ 2 0 FSTAT2 . - - - - - - - - 1 2 3 FIFO/DIR . . . - - - - - - - ; 10 FIFO READ +10V REF 1 I - - - : : : = - - H - - - - - - / r-'---'----L-.L, ~~~~i 5 BIPOLAR 2 ANALOG INPUT 39 BIT lOUT (Mmj) 40 BIT lOUT (MSB) 38 BIT 20UT 37 BIT 30UT 3BBIT 40UT 35 BIT 50UT 34 BIT BOUT 33 BIT 70UT 32 BIT 80UT 31 BIT 90UT 29 BIT 100UT 28 BIT11 OUT 27 BIT 12 OUT 26 BIT 13 OUT 25 BIT 14 OUT 22 BIT 15 OUT k/'V'....-. DIGITAL CORRECTION LOGIC 3 ~~N~ 17 EOC 15 LOOIC CONTROL AND TIMING '--TT.,....,r---',....,2~ ~~A~L~SB) ~~~~~~~ 16 24.18 +5V DIG.GND. +15V For Immediate Assistance, Dial 1-800-233-2765 4.11.13.30 ANA.GND. 14 OVERFLOW 12 -15V COMPBIN 1-51 ADS·930 ABSOLUTE MAXIMUM RATINGS PARAMETERS LIMITS UNITS -0.3 to +18 +0.3to-18 -0.3 to +7.0 -0.3 to +7.0 ±25 300 max +15V Supply -15V Supply +5VSupply Digital Inputs Analog Input Lead Temp. (10 Sec.) Voltsdc Voltsdc Voltsdc Voltsdc Volts °C FUNCTIONAL SPECIFICATIONS Apply over the operating temperature range and at ±15V dc and +5V dc unless otherwide specified. ANALOG INPUTS MIN. TYP. MAX. UNITS Input Voltage Range - - Input Impedance Input Cspacltance 1.9 - Dto +10 o to-lO ±5,±10 2 7 15 Volts Volts Volts KOhrns pf 2.0 - - - DIGITAL INPUTS logic Levels LogiC '1' Logic '0' Logic Loading '1" Logic Loading '0" - - Voltsdc Voltsdc - - 0.8 2.5 -100 - ±1 TBD TBD ±1112 TBD TBD LSB LSB LSB - ±1 TBD TBD ±1112 TBD TBD LSB LSB LSB - ±O.04 ±O.18 ±O.61 ±O.07 ±O.36 ±O.BS %FSR %FSR %FSR ±O.012 ±O.07 ±O.l ±O.04 ±O.13 ±O.17 %FSR %FSR %FSR ±O.012 ±O.07 ±O.l ±O.04 ±O.18 ±O.3 %FSR %FSR %FSR ±O.018 ±O.12 ±O.53 ±O.018 ±O.061 ±O.3 ±O.73 ±O.061 %FSR %FSR %FSR %FSR ±O.12 ±O.53 ±O.3 ±O.73 %FSR %FSR !IA !IA PERFORMANCE Inl Non-Un. @ fIN = 2SO KHz +25OC Oto +70 OC -55 to +125 OC DHI. Non-Lin, @ fiN =2SO KHz +25OC Oto+70OC -55 to +125 OC Full Scale Absolute Accuracy +25 OC. Ot0+70OC -55 to +125 OC Unipolar Zero Error, +25OC Oto +70 OC -55 to +125 OC Bipolar Zero Error, +25 OC (Tech Note 1) Oto+70OC -55 to +125 OC Bipolar Offset Error, +25 OC (Tech Note 1) Oto+70OC -55 to +125 OC Galn Error, +25 OC (See Tech Note 1) Oto+70OC -55 to +125 OC No MIssIng Codes 15 Bits@ 250 KHz fiN TBD Bits @2SO KHz fiN Resolution - - - - - Over 0 to +70 °C Over -55 to +125°C 16 Bits minimum OUTPUTS Output Coding (Pin Hi) (Pin Low) Logic Levels Logic '1" Logic '0" Logic Loading '1" Logic Loading '0" Internal Reference Voltage (+5V), +25 OC Drift External Current Internal Reference Voltage HOY), +25 OC Drift External Current DYNAMIC PERFORMANCE MIN. TYP. MAX. UNITS Straight bin.loffset bin.l2·s Camp. Camp. bin.lComp. offset bin.,C2C 2.4 - Voltsdc Volts de 0.4 -160 6.4 +5.0 :!l15 +5.02 :1;'30 5 Voltsdc pprn/OC rnA - -10.0 ±13 - -10.02 :1;'30 -5 Volts dc ppmlOC rnA -89 -83 -95 -88 - - FS-dB FS-dB -90 -87 -95 -89 - FS-dB FS-dB -82 -78 -87 -80 - FS-dB FS-dB 14 13 14.5 13.5 - - Bits Bits TBD 90 100 +4.98 - -9.98 - Total Harm. Distort. (.0.5 dB) DC to 100 KHz 100 KHz to 250 KHz Signal·to-Nolse Ratio (w/o distortion, -0.5 dB) OCto 100 KHz 100 KHz to 2SO KHz Signal·to-Noise Ratio & distortion, -0.5 dB DC to 100 KHz 100 KHz to 250 KHz Effective Bits, .0.5 dB OCto 100KHz 100KHz to 250 KHz Two-tone Intermodulation Distort. (ftN =100 KHz, 240 KHz, Fs=500 KHz, -0.5 dB) Slew Rate Aperture Delay Time Aparture Uncertainty s/H Acquishlon Time (to O.Ol%FS (10V step) Feedthrough Rajectlon @fiN=2SOKHz AID Conversion Rate +25OC Ot0+70OC -55 to +125 OC Input Bandwidth small Signal (-20 dB input) Full Power (0 dB input) Overvollage Recovery, ±12V - - - - - - - !IA rnA FS-dB - - V/IJSec· - ±to ±100 nSec. pSec. - 480 600 nSec. -96 - - dB SOO 500 500 - - - KHz KHz KHz 6 1.5 - - 8 2 600 1000 MHz MHz nSec. +14.25 -14.25 +4.75 +15.0 -15.0 +5.0 +15.75 -15.75 +5.25 Voltsdc Volts de Voltsdc - +47 -68 +84 2.1 +55 -75 +90 2.4 0.02 rnA rnA rnA Watts %FSR/%V - POWER REQUIREMENTS Power Supply Range +15V dc Supply -15V dc Supply +5V dc Supply Power Supply Current +15V de Supply -15V dc Supply +5V de Supply Ii) Power Dissipation Power Supply Rejection - - PHYSICAUENVIRONMENTAL Oper. Temp. Range, ·Me ·MM Storage Temp. Range Package Type Pins Weight - 0 +70 °C -55 +125 °C -65 il5O.. "C 40-pin hermetic sealed, ceramic DIP 0.010 x 0.018 inch Kovar 0.56 ounces (16 grams) maximum Specification footnotes +5V power usage at 1 TIL logic loading per data output b". Warm-up ffme to full specification: 5 minutes Ii) 1-52 DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194fTEL (508) 339-3000fTLX 174388/FAX (508) 339-6356 ADS-941 14-Bit, 1.0 MHz, High Resolution Sampling AID Converter PRELIMINARY PRODUCT DATA FEATURES • • • • • • • • 14-Bit resolution 1.0 MHz minimum throughput Internal Sample/Hold Functionally complete Small 32-pin DIP Low-power, 2.8 Watts Three-state output buffers Samples up to Nyquist INPUT/OUTPUT CONNECTIONS GENERAL DESCRIPTION PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 DATEL's ADS-941 is a 14-bit, 1_0 MHz sampling rate, functionally complete AID converter. The ADS-941 samples up to Nyquist with no missing codes. Packaged in a small 32-pin DIP, power requirements are ±15 volts and +5 volts with 2.8 Watts power dissipation. FUNCTION +10V REF. OUT BIPOLAR ANALOG INPUT SIGNAL GROUND OFFSET ADJUST ANALOG GROUND OVERFLOW COMPo BIN ENABLE +5V DIGITAL GROUND +15V -15V NO CONNECTION ANALOG GROUND EOC PIN 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 FUNCTION BIT 14 OUT (LSB) BIT 13 OUT BIT 12 OUT BIT 11 OUT BIT 100UT BIT90UT BIT80UT BIT70UT BIT60UT BIT50UT BIT40UT BIT30UT BIT20UT BIT lOUT (MSB) BIT lOUT (MSB) START CONVERT +10V REF 1 1 - - - : : = - - + - i f - - - - - - - - t 1 OUT (MSB) 10UT(MSB) 29BIT 20UT OFFSET ADJUST 5 BIPOLAR 2~~'--' 28BIT 30UT 27BIT 40UT 26BIT 50UT DIGITAL CORRECTION LOGIC ANALOG INPUT 3 25BIT 60UT 24BIT 70UT 23BIT 80UT 22BIT 90UT 21 BIT 100UT Cg~N~g~ 14 START CONV.32 20 BIT 11 OUT 19 BIT 120UT LOGIC CONTROL AND TIMING 18 BIT 13 OUT 17 BIT 14 OUT (LSB) 9 ENABLE EOC 16 SIGNAL GND 7 OVERFLOW 10 11 12 15 13 +5V DIG.GND. +15V ANA.GND. -15V For Immediate Assistance, Dial 1-800-233-2765 1-53 ADS·941 ABSOLUTE MAXIMUM RATINGS PARAMETERS OUTPUTS LIMITS +15V Supply (Pin 12) -15V Supply (Pin 13) +5V Supply (Pin 10) UNITS Volts de Volts de Volts de "0:3 to +18 +0:3 to -18 -0.3 to +7.0 Digital Inputs (Pins 8, 9, 32) Analog Input (Pin 3) Lead Temp. (10 Sec.) -0.3 to +7.0 ±25 300 max Volts de Volts °C Output Coding (Pin8Hi) (Pin 8 Low) Logic Levels Logic '1' Logic "0" Logic Loading "1" Logic Loading "0" Internal Reference Voltage, +25 °C Drift Extemal Currenl MIN. I TYP. I MAX. I UNITS Straighl bin.loltsel bin.l2's Comp. Compo bin.lComp. offsel bin., C2C 2.4 - - - - - +9.98 +10.0 ±13 - - 6.4 Voitsde Voitsde jJA mA +10.02 ±30 5 Volts dc ppm/oC mA 0.4 ·160 PERFORMANCE FUNCTIONAL SPECIFICATIONS Apply over the operating range and at ±15V de and +5V de unless otherwise specified.® ANALOG INPUTS Input Voltage Range Inpul Impedance Input Capacitance MIN. TYP. MAX. UNITS 2.2 - 010+10 ±5 2.5 7 - Volts Volts KOhms pf 2.0 - 0.8 5.0 ·200 - ±1/2 ±314 ±314 ±1 ±1 ±2 LSB LSB LSB - ±1 ±1/2 ±314 ±2 LSB LSB LSB - ±O.08 ±O.18 ±O.61 ±O.122 ±O.36 ±0.85 %FSR %FSR %FSR - ±O.012 ±O.07 ±O.l ±0.04 ±O.13 ±O.17 %FSR %FSR %FSR - ±O.04 ±O.07 ±O.l ±O.122 ±O.la ±O.3 %FSR %FSR %FSR - 15 DIGITAL INPUTS Logic Levels Logic "1' Logic "0' Logic Loading '1' Logic Loading '0' - - Volts dc Volts dc jJA jJA PERFORMANCE Int. Non-Lin. @ fiN =500 KHz +25°C Oto+70°C ·55 to +125 °C Dill. Non-Lin. @ fiN =500 KHz +25°C 010+70°C ·55 10 +125 °C Full Scale Absolute Accuracy (See Tech Note 1) +25°C. 010+70°C ·55 to +125 °C Unipolar Zero Error +25 °C (Tech Nole 1) 010 +70 °C ·55 10 +125°C Bipolar Zero Error +25°C (Tech Note 1) oto +70 °C ·55 to +125 °C Bipolar Offset Error, +25 °C (Tech Note 1) 010 +70 °C ·5510+125°C Gain Error (Tech Note 1) +25°C Oto +70 °C ·55 10+125 °C No Missing Codes 14 Bits@ 500 KHz fiN 13 Bits @ 500 KHz fiN Resolution 1-54 - - - ±O.018 ±O.12 ±O.53 ±O.061 ±O.3 ±O.73 %FSR %FSR %FSR ±O.018 ±O.12 ±O.53 ±O.12 ±O.3 ±O.73 %FSR %FSR %FSR Over Ihe Operating Temp. Range. 14 Bits Slew Rate Aperture Delay TIme Aperture Uncertainty SlH Acquisition TIme (10 O.006%FS (10V slep) Total Harm. Distort. (-0.5 dB) DC 10 100 KHz 100 KHz 10 SOO KHz Slgnal-Io·Noise Ratio (w/o dislortion, -0.5 dB) DC 10 100 KHz 100 KHz 10 500 KHz Signal-to-Noise Ratio & distortion, -0.5 dB DC to 100 KHz 100 KHz to 500 KHz Effective Bits, ·0.5 dB DC to 100 KHz 100 KHz to 500 KHz Two·tone Intermodulalion Distortion (fiN =100KHz, 240 KHz, Fs= 1.0 MHz, -D.5dB) Input Bandwidth Small Signal (-20 dB input) Full Power (0 dB input) Feedthrough Rejection @ fiN = 500 KHz Overvoltage Recovery, ±12V AID Conversion Rate +25°C Oto+70°C -5510 +125 °C - - - ±12 ±100 V/J.lSec. nSec. pSec. - 250 300 nSec. ·82 ·90 ·85 - FS·dB FS-dB -77 -90 -85 - FS-dB FS-dB -74 -69 -78 -73 - FS-dB FS-dB 12.4 11.8 13.1 12.3 -92 180 - ·77 -82 200 - - Bits Bits - - FS-dB - - MHz MHz - - 1000 2000 dB nSec. 1.0 1.0 1.0 1.1 1.1 1.05 - - MHz MHz MHz +14.25 -14.25 +4.75 +15.0 -15.0 +5.0 +15.75 -15.75 +5.25 Voltsdc Voltsdc Volts dc -- +68 -87 +150 2.8 +85 -95 +160 3.3 0.02 mA mA mA Watts %FSR/%V - +70 +125 °C °C - +lSO °C 6 1.75 -87 - POWER REQUIREMENTS Power Supply Range +15V dc Supply -15V dc Supply +5VdeSupply Power Supply CUrrent +15V dc Supply -15V de Supply +5V dc Supply (j) Power Dissipation Power Supply Rejection - - PHYSICAUENVIRONMENTAL Operating Temp. Range -MC ·MM Storage Temperature Range Package Type Weight 0 -55 -65 32-pin hermetic sealed, ceramic TDIP 0.42 ounces (12 grams) +5V power usage at 1 TIL logic loading per data output bit. lID Warm-up time to full specification: 20 minutes. (j) DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194fTEL (508) 339-3000fTLX 174388/FAX (508) 339-6356 ADS·941 TECHNICAL NOTES 1. Use external potentiometers to remove system errors or the small initial errors to zero. Use a 200 n trimming potentiometer in series with the analog input for gain adjustment. Use a short in place of the gain adjustment trim pot for operation without adjustments. Use a 20K trimming potentiometer with the wiper tied to pin 5 for zer%ffset adjustment (connect pin 5 to pin 15, analog ground for operation without adjustment). 2. Zero Adjustments Apply a precision voltage reference source between the analog input (pin 3) and signal ground (pin 4). Adjust the output of the reference source per Table 2. For unipolar, adjust the zero trimming potentiometer so that the output code flickers equally between 00 0000 0000 0000 and 00 0000 0000 0001 with the COMP BIN (pin 8) tied low (straight binary) or between 11 1111 1111 1111 and 11 1111 1111 1110 with the pin 8 tied high (complementary binary). 2. Rated performance requires using good high-frequency circuit board layout techniques. The analog and digital grounds are not connected internally. Avoid ground-related problems by connecting the digital and analog grounds to one point, the ground plane beneath the converter. Due to the inductance and resistance of the power supply return . paths, return the analog and digital ground separately to the power supplies. For bipolar operation, adjust the potentiometer such that the code flickers equally between 10 0000 0000 0000 and 10 0000 0000 0001 with pin 8 tied high (offset binary) or between 01 1111 1111 1111 and 01 1111 1111 1110 with pin 8 tied low (complementary offset binary). 3. Bypass the analog and digital supplies and the +1 OV reference (pin 1) to ground with a 4.7 ~F, 25V tantalum electrolytic capacitor in parallel with a 0.1 ~F ceramic capaCitor. Bypass the + 1OV reference (pin 1) to analog ground (pin 15). 4. Obtain straight binary/offset binary output coding by tying COMP BIN (pin 8) to +5V dc or leaving it open. The device has an internal pull-up resistor on this pin. To obtain com.plementary binary or complementary offset binary output coding, tie the COMP BIN pin to ground. The COMP BIN signal is compatible to CMOSmL logic levels for those users desiring logic control of this function. Two's complement coding requires use of the MSB (pin 31) with COMP BIN (pin 8) tied high, adjusting the potentiometer such that the code flickers between 00 0000 0000 0000 and 00 0000 0000 0001. 3. Full-Scale Adjustment Set the output of the voltage reference used in step 2 to the value shown in Table 2. Adjust the gain trimming potentiometer so that the output code flickers equally between 11 1111 1111 1110 and 11 1111 1111 1111 for COMP BIN (pin 8) tied low for unipolar operation or tied high for bipolar operation (straight binary/ offset binary) or between 00 0000 0000 0000 and 00 0000 0000 0001 for COMP BIN tied high for unipolar operastionor tied low for bipolar operation (complementary binary! complementary offset binary). 5. To enable the three-state outputs, connect ENABLE (pin 9) to a logic "a" (low). To disable, connect ENABLE (pin 9) to a logic "1" (high). Two's complement coding requires use of the MSB (pin 31) with the COMP BIN (pin 8) tied high, adjusting the gain trimming potentiometer so that the output code flickers equally between 01111111111110 and 01111111111111. CALIBBATION"PROCEDURE 1. Connect the converter per Figure 3, and Table 1 for the appropriate full-scale range (FSR). Apply a pulse of 50 nanoseconds minimum to the START CONVERT input (pin 32) at a rate of 200 KHz. This rate is chosen to reduce flicker if LED's are used on the outputs for calibration purposes. 4. To confirm proper operation of the device, vary the precision reference voltage source to obtain the output coding listed in Table 3. I_HOLD MODE SeTIUNG 50 nSec MIN NOTE: NOT DRAWN TO SCALE _1 Table 1. Input Connections INPUT RANGE INPUT PIN TIE TOGETHER I~ START CONVERT -T"---1j N S1H ACO. TIME 5/H Oto-10V ±5V Pin 3 Pin 3 Pins 2 and 4 Pins 1 and 2 ~ HOLD CONTROL OUT r SAMPLE 10 nSec MIN., 25 nSec MAX. (INTERNAL) BUSY AlOEOC ~I OUT --+1 OUTPUT DATA Table 2. Zero and Gain Adjust FSR oto +10V ±5V ZERO ADJUST +1/2 LSB -305 ~V -305 ~V GAIN ADJUST FS-1!2 LSB -9.999085V -4.999085V For Immediate Assistance, Dial 1-800-233-2765 ,...- 30 nSec MIN 1+-20 nSec MIN., 35 nSec MAX I - 600 nSec MIN----I DATAN-1 VALID ---==J1....wnSec MAX DATA INHIBITED -25nSecMIN I I 1><1 DATANVALID INVALID 10 nSec MAX ~II+-"NABLED DATA N VALID NOTE: Aetriggeting the START CONVERT pulse before E5Cgoes low will not initiate a new conversion. NOTE: The specifications listed apply over the full operating temperature range unless otherwise specified. Figure 2. AD5-941 Timing Diagram 1-55 " ADS·941 • Table 3. Output Coding 01 1000 0000 0000 01 0000 0000 0000 00 0000 0000 0000 10 0000 0000 0000 10 1000 0000 0000 10000000000001 10 00000000 0000 +15V -15V 4.7~F 4.7~F 13 9 31 30 29 2S 27 26 25 24 +10V REF AD5-941 23 Oto+10V 1.101 MAX (28,0) -I 11 10 ANALOG GROUND BIPOLAR -1/2 FS -3/4 FS -FS+1 LSB -FS MECHANICAL DIMENSIONS INCHES (MM) 4.7~F 1_ 15 o +5V 0.1W 12 +3/4 FS +1/2 FS 22 21 20 19 18 17 7 16 ANALOG INPUT COMPBIN START CONVERT DO NOT CONNECT SIGNAL GROUND ~0.010 X 0.018 ~ ENABLE BIT 1 (MSB) BIT 1 (MSB) BIT2 BIT 3 BIT4 BITS BIT6 BIT7 BITS BIT9 BIT10 BIT11 BIT12 BIT 13 BIT 14 (LSB) OVERFLOW EOC KOVAR Pins 17 16 -, 15 SPACES 1.712 MAX. (43,5) bl BOTTOM VIEW ATO 100. (2,5) _I ,---,-_ _",,32=--....I -15V 1_ +15V ZERO/OFFSET ADJUST 0.900 (22,9) -I NOTE: Pins have a 0.025 inch, ±0.01 stand-off from case. Figure 3. Typical ADS·941 Connection Diagram dB 10 20 ORDERING INFORMATION 30 MODEL NUMBER 40 so ADS-941 MC ADS-941 MM 60 OPERATING TEMP. RANGE SEAL 0 °C to +70 °C -55°C to +125 °C Hermetic Hermetic 70 ACCESSORY 80 90 j I. I 100 200 KHz 300 II I 400 Figure 4. FFT Analysis of ADS·941 1-56 soo ADS.EVAL1 Evaluation Board (without ADS-941) Receptacle for PC board mounting can be ordered through AMP Inc., Part # 3-331272-8 (Component Lead Socket), 32 required. For availibility of MIL-STD-883B versions, contact DATEL. DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194ITEL (508) 339-3000ITLX 174388/FAX (508) 339-6356 ADS-942 14-Bit, 2.0 MHz, High Resolution Sampling AID Converter PRELIMINARY PRODUCT DATA FEATURES • • • • • • • • 14-Bit resolution Internal Sample/Hold 2.0 MHz minimum throughput Functionally complete Small 32-pin DIP Low-power 2.9 Watts Three-state output buffers Samples up to Nyquist INPUT/OUTPUT CONNECTIONS PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 GENERAL DESCRIPTION DATEL's ADS-942 is a 14-bit, 2.0 MHz sampling rate, functionally complete AID converter. The ADS-942 samples up to Ny. quist with no missing codes. Packaged in a small 32-pin DIP, power requirements are ±15 volts and +5 volts with 2.9 Watts power dissipation. +10V REF 1 FUNCTION +10V REF. OUT BIPOLAR ANALOG INPUT SIGNAL GROUND OFFSET ADJUST ANALOG GROUND OVERFLOW COMPo BIN ENABLE +5V DIGITAL GROUND +15V -15V DO NOT CONNECT ANALOG GROUND EOC PIN 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 FUNCTION BIT 14 OUT (LSB) BIT 130UT BIT 12 OUT BIT 11 OUT BIT100UT BIT90UT BIT80UT BIT70UT BIT60UT BIT50UT BIT 4 OUT BIT 3 OUT BIT20UT BIT 1 OUT (MSB) BIT 1 OUT (MSB) START CONVERT r---;;;=----1-+------l 31 BIT 1 OUT (MSB) 30 BIT 1 OUT (MSB) OFFSET ADJUST 29BIT 20UT 28BIT 30UT 5 27BIT 40UT BIPOLAR 2 .....r'~"DIGITAL CORRECTION LOGIC ANALOG INPUT 3 26BIT 50UT 25BIT 60UT 22BIT 90UT 21 BIT 10 OUT 20 BIT 11 OUT cO~N~gi 14 START CONV.32 EOC 16 LOGIC 19 BIT 12 OUT CO~~OL 18 BIT 13 OUT t~j=T~IM:I~NGJ~~~~~~~~~~~~~;::~===~===~~~j17BIT14OUT(LSB) 9 ENABLE 7 OVERFLOW 4 10 11 12 15 13 SIGNALGND +5V DIG. GND. +15V ANA. GND. -15V For Immediate Assistance, Dial 1-800-233-2765 1-57 ADS·942 ABSOLUTE MAXIMUM RATINGS PARAMETERS LIMITS +15V Supply (Pin 12) ·15V Supply (Pin 13) +5V Supply (Pin 10) -0.3 to +18 +0.3 to -18 -0.3 to +7.0 Digital Inputs (Pins 8, 9, 32) Analog Input (Pin 3) Lead Temp. (10 Sec.) Volts de Volts de Volts de Volts de Volts °C -0.3 to +7.0 ±25 300 max Apply over the operating temperature range and at ±15V de and +5V de unless otherwise specified.<2l MIN. Input Voltage Range - 2.2 Input Impedance Input capacitance - TYP. Oto +10 ±5 2.5 7 MAX. UNITS - Volts Volts KOhms 15 pi - DIGITAL INPUTS Logic Levels Logic "1" Logic "0" Logic Loading "1" Logic Loading '0" 2.0 - - - - 0.8 5.0 -200 Vo~s de Volts de IlA IlA PERFORMANCE Inl. Non-Lin. @ /IN = 1 MHz +25°C Oto +70 °C -55 to +125 °C 0111. Non-Lin. @fiN = 1 MHz +25°C Oto +70 °C -55 to +125 °C Full Scale Absolute Accuracy +25°C. Oto+70°C -55 to +125 °C Unipolar Zero Error, +25°C Oto+70°C ·55 to +125 °C Bipolar Zero Error, +25 °C (Tech Note 1) Oto +70 °C -55 to +125 °C Bipolar Offset Error, +25 °C (Tech Note 1) oto +70 °C ·55 to+ 125°C Gain Error, +25 °C (See Tech Note 1) oto +70 °C ·55 to+ 125°C No Missing Codes 14 Bits@ 1 MHz fiN 13 Bits@ 1 MHz fiN Resolution - - ±1/2 ±3/4 ±1 ±1 ±1.5 ±2.5 LSB LSB LSB - ±112 ±3/4 ±1 ±1 ±1.25 ±2.5 LSB LSB LSB - ±O.OS ±0.18 ±D.61 ±D.t22 ±D.36 ±D.85 %FSR %FSR %FSR - ±D.012 ±D.07 ±D.l ±D.04 ±0.13 ±D.17 %FSR %FSR %FSR ±D.04 ±D.07 ±D.l ±D.122 ±D.18 ±D.3 %FSR %FSR %FSR ±D.018 ±D.12 ±D.53 ±D.018 ±D.061 ±D.3 ±D.73 ±D.t22 %FSR %FSR %FSR %FSR ±D.12 ±D.53 ±D.3 ±D.73 %FSR %FSR - - - - Output Coding (Pin 8 Hi) (Pin 8 Low) logic Levels Logic '1' Logic '0' Logic Loading "1" Logic Loading '0' Internal Reference Voltage, +25 °C Drift External Current MIN. TYP. I MAX. I UNITS Straight binary/offset binary Complementary binary 2.4 - - - 0.4 ·160 6.4 Volts de Volts de ~ mA +10.0 ±13 +10.02 ±30 5 Volts de ppm/DC mA -79 -73 ·85 -79 - FS-dB FS-dB ·78 -73 ·85 -79 - - FS-dB FS-dB ·72 -68 ·77 -71 - FS-dB FS·dB 12.3 11.7 13.0 12.3 - Bits Bits -92 - - FS-dB 6 1.75 210 - - - - +9.98 - - DYNAMIC PERFORMANCE FUNCTIONAL SPECIFICATIONS ANALOG INPUTS OUTPUTS UNITS Total Harm. Distort. (-0.5 dB) OCto 100KHz 100 KHz to 1 MHz Signal·to·Noise Ratio (w/o distortion, .(l.5 dB) OCto 100KHz 100 KHz to 1 MHz Signal·to·Noisa Ratio & distortion, -0.5 dB DC to 100 KHz 100 KHz to 1 MHz Effective Bits, -0.5 dB OCto 100 KHz 100 KHz to 1 MHz Two·tone Intermodulation Distortion (fiN =100 KHz, 240 KHz, Fs=2.0 MHz, -0.5 dB) Input Bandwldlh Small Signal (·20 dB input) Full Power (0 dB input) Slew Rate Aperture Delay TIme Aperture Uncertainty, Rms S/H Acquisition TIme (to 0.006%FS (10V step) Feedlhrough Refection @ftN=lMHz Overvoltage Recovery, ±12V AID Conversion Rete +25°C oto +70 °C ·55to+125°C - - 250 - ±10 ±10 MHz MHz VI!lSec. nSec. pSec. - 120 150 nSec. - - - 1000 2000 - dB nSec. 2.0 2.0 2.0 2.1 2.1 2.05 - - - MHz MHz MHz +14.25 ·14.25 +4.75 +15.0 -15.0 +5.0 +15.75 ·15.75 +5.25 Volts dc Voltsdc Voltsdc - +70 ·80 +155 2.9 +87 -98 +165 3.4 0.02 mA mA mA Watts %FSRI%V - +70 +125 °c °C ·85 - POWER REQUIREMENTS Power Supply Range +15V de Supply -15V dc Supply +5V de Supply Power Supply Current +15V dc Supply -15V dc Supply +5V de Supply (j) Power Dissipslion Power Supply Rejection - - PHYSICAL/ENVIRONMENTAL Operating Temp. Range ·MC ·MM Storage Temperature Range Package Type Weight Over 0 to 70°C Over -55 to +125°C 14 Bits 0 -55 - - -65 +150 °C 32-pin hennetic sealed, ceramic DIP 0.42 ounces (12 grams) +5V power usage at 1 TIL logiC loadmg per data output bit. lID Wann·up time to lull specification: 20 minutes. (j) 1-58 DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194fTEL (508) 339-3000fTLX 174388/FAX (508) 339-6356 ADS-942 TECHNICAL NOTES 1. Use external potentiometers to remove system errors or the small initial errors to zero. Use a 200 Q trimming potentiometer in series with the analog input for gain adjustment. Use a short in place of the gain adjustment trim pot for operation without adjustments. Use a 20K trimming potentiometer with the wiper tied to pin 5 for zer%liset adjustment (connect pin 5 to pin 15, analog ground for operation without adjustment). 2. Zero Adjustments Apply a precision voltage reference source between the analog input (pin 3) and signal ground (pin 4). Adjust the output of the reference source per Table 2. For unipolar, adjust the zero trimming potentiometer so that the output code flickers equally between 00 0000 0000 0000 and 00 0000 0000 0001 with the COMP BIN (pin 8) tied low (straight binary) or between 11 1111 1111 1111 and 11 1111 1111 1110 with the pin 8 tied high (complementary binary). 2. Rated performance requires using good high-frequency circuit board layout techniques. The analog and digital grounds are not connected internally. Avoid ground-related problems by connecting the digital and analog grounds to one point, the ground plane beneath the converter. Due to the inductance and resistance of the power supply return paths, return the analog and digital ground separately to the power supplies. 3. Bypass the analog and digital supplies and the +10V reference (pin 1) to ground with a 4.7I1F, 25V tantalum electrolytic capacitor in parallel with a 0.1 I1F ceramic capacitor. Bypass the +1 OV reference (pin 1) to analog ground (pin 15). 4. Obtain straight binary/oliset binary output coding by tying COMP BIN (pin 8) to +5V dc or leaving it open. The device has an internal pull-up resistor on this pin. To obtain complementary binary or complementary oliset binary output coding, tie pin 18 to ground. The pin 18 signal is compatible to CMOSITTL logic levels for those users desiring logic control of this function. For bipolar operation, adjust the potentiometer such that the code flickers equally between 10 0000 0000 0000 and 10 0000 0000 0001 with pin 8 tied high (oliset binary) or between 011111 1111 1111 and 01111111111110 with pin 8 tied low (complementary oliset binary). Two's complement coding requires use of the IiiffiB (pin 31) with CQMP BIN (pin 8) tied high, adjusting the potentiometer such that the code flickers between 00 0000 0000 0000 and 00 0000 0000 0001. 3. Full-Scale Adjustment Set the output of the voltage reference used in step 2 to the value shown in Table 2. Adjust the gain trimming potentiometer so that the output code flickers equally between 11 1111 1111 1110 and 11 1111 1111 1111 for CQMP BIN (pin 8) tied low for unipolar operation or tied high for bipolar operation (straight binary/ oliset binary) or between 00 0000 0000 0000 and 00 0000 0000 0001 forCOMP BIN tied high for unipolar operastionor tied low fdr bipolar operation (complementary binary/ complementary oliset binary). 5. To enable the three-state outputs, connect ENABCE (pin 9) to a logic "0" (low). To disable, connect pin 9 to a logic "1" (high). Two's complement coding requires use of the MSB (pin 31) with the COMP BIN (pin 8) tied high, adjusting the gain trimming potentiometer so that the output code flickers equally between 01 1111 1111 1110 and 01 1111 1111 1111. CALIBRATION PROCEDURE 1. Connect the converter per Figure 3, and Table 1 for the appropriate full-scale range (FSR). Apply a pulse of 35 nanoseconds minimum to the START CONVERT input (pin 32) at a rate of 200 KHz. This rate is chosen to reduce flicker if LED's are used on the outputs for calibration purposes. 4. To confirm proper operation of the device, vary the precision reference voltage source to obtain the output coding listed in Table 3. , rt- HOLD MODE SETTliNG ~I ....... , STAAT CONVERT N Table 1. Input Connections INPUT RANGE o to +10V ±5V INPUT PIN Pin3 Pin 3 TIE TOGETHER Pins 2 and 4 Pins 1 and 2 '+r 35 nSec MIN, 50 nSec TYP -;----'1 ROCD BUSY Oto +10V ±5V ZERO ADJUST +1/2 LSB -30511V -30511V GAIN ADJUST FS-1/2 LSB +9.999085V -4.999085V For Immediate Assistance, Dial 1-800-233-2765 -, OUT ~l I.of- 20 nSec MIN., 35 nSec MAX I 4- 25 nSec MIN I I+-::--=-: 6OOnSecMIN---i I DATA N·' VALID IXI DATA N VALID LNVALID ~ 1+-10 nSec MAX DATA INHIBITED Table 2. Zero and Gain Adjust ......... 30nSec MIN I SAMPLE '0 nSec MIN., 2S nSoc MAX. AJOECC OUTPUT DATA FSR - SIH ACQ. TIME SIH CONTROL OUT IINTERNAL) NOTE: NOT DRAWN TO SCALE 1. Retriggerlng the start convert pulse before will not initiate a new conversion. 10 nSec MAX ___ 1~NABl.EO DATA N VALID EOC goes low 2. The specifications cited apply over the full operating tam- .perature range. Figure 2. ADS-942 Timing Diagram 1-59 ADS-942 Table 3. Output Coding STRAIGHT UNIPOLAR SCALE FS -1 LSB 7/8 FS 314 FS 112 FS 1/4 FS 118 FS 1LSB 0 BIN INPUT RANGES, V de OUTPUT CODING o to +10V IMSB LSB +9.999390 11111111111111 +8.750000 11 1000 0000 0000 +7.500000 11 0000 0000 0000 +5.000000 10 0000 0000 0000 +2.500000 01 0000 0000 0000 +1.250000 00 1000 0000 0000 +0.000610 00 0000 0000 0001 0.000000 00 0000 0000 0000 COMP BINARY MSB LSB 00 0000 0000 0000 00 0111 1111 1111 00 111111111111 01 1111 1111 1111 10 111111111111 11 0111 1111 1111 11111111111110 11111111111111 INPUT RANGE HOVde -4.99939 -3.75000 -2.50000 0.00000 +2.50000 +3.75000 +4.99939 +5.00000 MSB LSB 01 1111 1111 1111 01 1000 0000 0000 01 0000 0000 0000 00 0000 0000 0000 10 0000 0000 0000 10 1000 0000 0000 10 0000 0000 0001 10 00000000 0000 BIPOLAR SCALE +FS -1 LSB +3/4 FS +1/2 FS a -1/2 FS -3/4 FS -FS +1 LSB -FS MECHANICAL DIMENSIONS INCHES (MM) .5V 1.101 MAX (28,0) I ~0.010 X 0.G18 KOVAR Pins 17 ,,,16 ,, ,, ,, ,, BOTTOM ,,, VIEW ,, ,, , ! 32 0.190 MAX 4'9} I ~ ~ 0.150 MIN. (3,8) TT 15 SPACES AT 0.100 (2,5) 1.712 MAX. (43,S) ~ 0.900 (22,9) 20K -15V +15V ZEROiOFFSET ADJUST NOTE: Pins have a 0.025 inch, to.01 stand·off from case. Figure 3. Typical AD5-942 Connection Diagram dB ORDERING INFORMATION ·10 -20 MODEL NUMBER -30 ..w ADS-942MC ADS-942MM -50 .eo ACCESSORY ·70 .eo .go ·100 II I. ~ II I ~ ~ U M MHz I M ~ M Figure 4. FFT Analysis of AD5-942 1-60 M W OPERATING TEMP. RANGE a °C to +70 °C -55 °C to +125 °C ADS-EVALI SEAL Hermetic Hermetic Evaluation Board (without ADS-942) Receptacle for PC board mounting can be ordered through AMP Inc., Part # 3-331272-8 (Component Lead Socket), 32 required. For availibility of MIL-STD-883B versions, contact DATEL. DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-11941TEL (508) 339-30001TLX 174388/FAX (508) 339-6356 ADS-944 14-Bit, 5.0 MHz, High Resolution Sampling AID Converter ADVANCED PRODUCT DATA APPLICATIONS FEATURES • • • • • • • • Spectrum analysis Imaging Radar Medical instrumentation High-speed data acquisition systems 14-8it resolution Internal Sample/Hold 5.0 MHz minimum throughput Functionally complete Small 32-pin DIP Low-power 3.4 Watts Three-state output buffers Samples up to Nyquist I/O CONNECTIONS GENERAL DESCRIPTION DATEL's ADS-944 is a 14-bit, 5.0 MHz sampling rate, functionally complete sampling AID converter. The ADS-944 samples up to Nyquist with no missing codes. Packaged in a small 32-pin DIP, power requirements are ±15 volts and +5 volts with 3.4 Watts power dissipation. The ADS-944 is offered in the comercial 0 to +70 °C and military -55 to +125°C operating temperature range. PIN FUNCTION PIN FUNCTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 +10V REF. OUT BIPOLAR ANALOG INPUT SIGNAL GROUND OFFSET ADJUST ANALOGGND OVERFLOW COMPo BIN. ENABLE +5V DIGITAL GROUND +15V -15V DO NOT CONNECT ANALOG GROUND EOC 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 BIT 14 OUT (LSB) BIT 130UT BIT 120UT BIT 11 OUT BIT 100UT BIT 9 OUT BIT 8 OUT BIT 7 OUT BIT60UT BIT50UT BIT 4 OUT BIT 3 OUT BIT20UT BIT lOUT !~~~! BIT lOUT START CONVERT +10V REF 1 f---:::=--+-t--------j 10UT(MSB) 10UT(MSB) OFFSET ADJUST 29 BIT 20UT 28 BIT 30UT 5 27 BIT 40UT BIPOLAR 2 ..... "'.A.~ 26BIT 50UT DIGITAL CORRECTION LOGIC ANALOG INPUT 3 25 BIT 60UT 24BIT 70UT 23 BIT 80UT 22 BIT 90UT 21 BIT100UT 20 BIT 11 OUT cg~N~g~ 14 19BIT 120UT LOGIC CONTROL AND TIMING START CONV.32 18BIT 130UT 17 BIT 14 OUT (LSB) 9 ENABLE EOC 16 7 OVERFLOW 4 10 11 12 15 13 SIGNAL GND +5V DIG.GND. +15V ANA. GND. ·15V For Immediate Assistance, Dial 1-800-233-2765 1-61 Contact DATEL for up-to-date information on products covered by "Advanced" and "Preliminary" product data sheets. Dial 1-800-233-2765 for Applications Assistance 1-62 DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194fTEL (508) 339-3000fTLX 174388/FAX (508) 339-6356 ADS-945 14-Bit, 10.0 MHz, High Resolution Sampling AID Converter - ADVANCED PRODUCT DATA FEATURES 14-Bit resolution 10 MHz sampling rate Functionally complete Internal S/H Small 40-pin DIP Low-power, 4.2 Watts Three-state output buffers Samples up to Nyquist 16 word FIFO memory 1/0 Connections GENERAL DESCRIPTION DATEL's ADS-945 is a 14-bit, 10 MHz sampling rate, functionally complete ND converter with internal FIFO. The ADS-945 samples up to Nyquist with no missing codes. Packaged in a small 40-pin TDIP, power requirements are ±15 Volts and ±5 Volts with 4.2 Watts power dissipation. APPLICATIONS Spectroscopy Spectrum analysis • Imaging Radar Medical instrumentation High-speed data acquisition systems Function Function +5V REFERENCE OFFSET ADJUST ANALOG INPUT HIGH ANALOG INPUT LOW BIPOLAR -10V REFERENCE ENABLE LOW B9-14 GAIN ADJUST OVERFLOW DO NOT CONNECT -5V BIT 14 OUT (LSB) BIT 130UT BIT 120UT BIT 11 OUT BIT 100UT BIT90UT FSTAT1 FSTAT2 BIT 1 OUT (MSB) START CONVERT FIFO/DIR FIFO READ BIT 80UT BIT 7 OUT BIT60UT BIT50UT BIT 40UT BIT3 OUT BIT20UT BIT 1 OUT (MSB) +5V !JIGITAL GRQUND ENABLE HIGH (B1-8) S/H OUT COMP BIN -15V ANALOG GROUND ANALOG GROUND +15V mru FSTAT1 FSTAT2 GAIN AOJUST FIFOJDIR FIFO READ -10V REF BIT BIT BIT BIT BIT BIT BIT BIT BIT BIT BIT BIT BIT BIT BIT +5V REF OFFSET ADJUST BIPOLAR StH OUT ANALOG HIGH INPUT LOW START CONY. LOGIC CONTROL AND TIMING SIGNAL GROUND ~~~~~~~~~~~~~~~=L===l___J +5V DIG. GND. +15V ANA. GND. -15V ·5V DO NOT 1 OUT (MSll) 1 OUT (MSB) 20UT 30UT 40UT 50UT 60UT 70UT 80UT 9 OUT 10 OUT 11 OUT 12 OUT 13 OUT 14 OUT (LSB) ~LOW ENABLE HIGH OVERFLOW COMPBIN CONNECT For Immediate Assistance, Dial 1-800-233-2765 1-63 Contact DATEL for up-to-date information on products covered by "Advanced" and "Preliminary" product data sheets. Dial 1-800-233-2765 for Applications Assistance 1-64 DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194rrEL (508) 339-3000rrLX 174388/FAX (508) 339·6356 ADS-976 16-bit, 200 KHz, Low-Power Sampling AID Converter PRELIMINARY PRODUCT DATA FEATURES 16-bit resolution • 200 KHz sampling rate • Compatible to industry standard ADC76, AD376, AD1376 • Internal sample-hold • Small 32-pin DIP Low-power, 1.8 Watts Samples to Nyquist • 16 word FIFO memory INPUT/OUTPUT CONNECTIONS GENERAL DESCRIPTION PIN DATEL's ADS-976 is a 16-bit, 200 KHz sampling rate, functionally complete AID converter with an internal samplehold. The ADS-976 samples up to Nyquist with no missing codes. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 The internal FIFO can be either bypassed or utilized with full (16 words) or half-full (8 words). The FIFO capability still allows the ADS-976 to be compatible to the industry pin-out versions for 16-bit parallel output applications. Packaged in a small 32-pin DIP, power requirements are ±15 volts and +5 volts with a 1.8 Watts power disSipation. FUNCTION PIN FUNCTION BIT lOUT (MSB) BIT 2 OUT BIT30UT BIT40UT BIT 5 OUT BIT60UT BIT 7 OUT BIT 8 OUT BIT 9 OUT BIT 10 OUT BIT 11 OUT BIT 12 OUT BIT 130UT BIT 14 OUT BIT 15 OUT BIT 16 OUT (LSB) 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 FIFO READ START CONVERT +5V GAIN ADJUST +15V OFFSET ADJUST BIPOLAR OFFSET 10V 20V FIFO/DIR ANALOG GROUND ·15V FSTAT2 DIGITAL GROUND EOC FSTATl 1----;==:=;;;;;:=====;:;~r==;_----;:========:]17 FSTAT1 , - - - - - - - - - 1 2 0 FSTAT2 ADJ~~~ 2911--==--Hf--------, B!~~~ , - - - - - - - - j 23 FIFO/DiR . - - - - - - - 1 3 2 FIFO READ 26ir-....y,{I,--Hf------"'""l r--1.--1--'-1 1 BIT lOUT (MSB) 2 BIT 20UT DIRECTor FIFO 10V 25 20V 24f--"M.....-'VI/Irl ~~N~ 31 3 4 5 6 7 8 9 BIT BIT BIT BIT BIT BIT BIT 30UT 40UT 50UT 60UT· 70UT 80UT 90UT 10 BIT 10 OUT 11 BIT 11 OUT 12 BIT 12 OUT 13BIT 13 OUT 14 BIT 140UT 15 BIT 150UT 16 BIT 16 (LSB) LOGIC CONTROL AND TIMING roc 18 30 19 28 22 21 +5V DIG. GND. +15V ANA.GND. -15V For Immediate Assistance, Dial 1-800-233-2765 1-65 Contact DATEL for up-to-date information on products covered by "Advanced" and "Preliminary" product data sheets. Dial 1-800-233-2765 for Applications Assistance 1-66 DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194rrEL (508) 339-3000rrLX 174388/FAX (508) 339-6356 AID CONVERTERS Linearity Error Power (Watts) 0.050 ±1/2 LSB 0.25 18-Pin DIP 2-1 8 0.040 ±1/2 LSB 1.25 24-Pin DIP 2-9 ADG-208 8 0.050 ±3/4 LSB 0.60 24-Pin DIP 2-5 ADC-304 8 0.050 ±1/2 LSB 0.39 28-Pin DIP 2-13 ADG-530 12 0.350 ±3i4 LSB 2.10 32-Pin DIP 2-33 ADC-500 12 0.500 ±1 LSB 1.70 32-Pin DIP 2-17 ADC-505 12 0.550 ±1 LSB 1.70 32-Pin DIP 2-17 ADC-508 12 0.700 ±1 LSB 1.70 32-Pin DIP 2-21 ADC-520 12 0.800 ±1/2 LSB 1.60 32-Pin DIP 2-29 ADC-521 12 0.800 ±1/2 LSB 1.60 32-Pin DIP 2-29 ADC-511 12 1.0 ±3/4 LSB 1.25 24-Pin DIP 2-25 ADC-HZ12B 12 8 ±1/2 LSB 1.5 32-Pin DIP 2-55 ADC-HX12B 12 20 ±1/2 LSB 1.5 32-Pin DIP 2-55 ADG-HC12B 12 300 ±1/2 LSB 0.17 32-Pin DIP 2-47 ADC-908 14 1.0 ±1/2 LSB 2.70 32-Pin DIP 2-37 ADC-914 14 2.4 ±1 LSB 1.20 24-Pin DIP 2-41 Resolution (Bits) Conversion Time (lisec) ADG-207 7 ADC-228 Model New =or Immediate Assistance, Dial 1-800-233-2765 Case Page 2-i Contact DATEL for your Data Acquisition component needs. Dial 1-800-233-2765 for Applications Assistance 2·ii DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048·1194rrEL (508) 339-3000rrLX 174388/FAX (508) 339-6356 ADC-207 7-Bit, 20 MSPS CMOS Flash AID ;4 FEATURES 7-Bit flash AID converter • 20 MHz Sampling rate Low-power (250 mW) • +5V dc Operation • 1.2 Micron CMOS • 7-bit latched 3-state output with overflow bit Surface mount versions • MIL-STD-883 versions • No missing codes MECHANICAL DIMENSIONS -I 0.250 ±o.oos GENERAL DESCRIPTION The ADC-207 is the industry's first 7-bit flash converter using a high-speed 1.2 micron CMOS process. This process offers some very distinctive advantages over other processes, making the ADC-207 a very unique device. The smaller geometrics of the process achieves high-speed, better linearity ·and better temperature performance. Since the ADC-207 is a CMOS device, it also has very low power consumption (250 mW). The device draws power from a single +5V supply, and is conservatively rated for 20 MHz operation. The ADC-207 allows using sampling apertures as small as 12nS, making it more closely approach an ideal sampler. The small sampling apertures also let the device operate at greater than 20 MHz. o.os~. 1 1_ D TOP (LCC Version) -10.40050. ~g:g~~ D. O()3~I(J9' --L T -11- 0.020-±O.OOS ~ ..-L. 122ImMW·'7014.3' T .1)85 . ...L ---I 1-. 10• I 1 (2.51 ____ I" I"" II III I0.130 Max. t ~()111H 0I)4hl 16 2. 10 INPUT/OUTPUT CONNECTIONS For Immediate Assistance, Dial 1-800-233-2765 DIP PINS FUNCTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 CLOCK IN DIGITAL GROUND -REFERENCE ANAIOIG INPUT MIDPOINT + REFERENCE ANALOG GROUND CSl CS2 OVERFLOW BITl (MSB) BIT 2 BIT3 BIT 4 BITS BIT6 BIT7 +VDD LCC PINS 1 4 5 6 7 8 9 11 12 13 14 16 17 19 20 21 23 24 2-1 ADC·207 FUNCTIONAL SPECIFICATIONS (Typical at +5Vdc power, +25 deg. C, ..20 MHz clock, +Reference = 5V, -Reference = Ground, unless noted) MIN. DESCRIPTION TYPICAL I MAX. I UNITS - +7.0 Vdc Vdc Vdc ABSOLUTE MAXIMUM RATINGS Power supply voltage (+Vdd, pin 18) Digital inputs Analog input -0.5 -0.5 -0.5 - Reference inputs Digital outputs (short circuit protected to ground) Lead temperature, 10 sec. ma Ambient temperature -0.5 -0.5 - +5.5 +Vdd +0.5 +Vdd +5.5 - - +300 OC -65 - +150 OC Vdc Vdc Power supply range (+Vdd) Power supply current Power dissipation ENVIRONMENTAL - MIN. TYPICAL I MAX. I UNITS +3.0 +5.0 +50 250 +5.5 +70 Vdc mA mW - 385 MECHANICAL Operating temp, range: lC/MC Versions MMilM/883 Versions Storage temp. range 0 -55 -65 - +70 +125 +150 - ·C ·C· OC Package type DIP LCC 18-pin hermetic sealed, ceramic DIP 24-pin hermetic sealed, ceramic LCC Pin material .010 x .018 inch Kovar NOTES: 1. At full power input and chip selects enabled 2. At 4 MHz input and 20 MHz clock INPUTS ANALOG SIGNAL INPUT single-ended, non-isolated Input range dc-20 MHz Input impedance Input capacitance, full input range DIGITAL INPUTS: Logic "1" level Logic "0" level Logic "1" loading Logic "0" loading Sample pulse width, during sampling portion of clock Reference ladder resistance 3. For 10-step, 40 IRE NTSC ramp test - 0 - 1000 10 2.0 - - V - Ohms pF - - - V V microamps microamps nS 330 - Ohms +/-1 +/-1 12 +5.0 0.8 +/-5 +/-5 DIGITAL OUTPUTS Data coding Straight binary Data output resolution Logic "1" level Logic "0" level atl.6mA Logic "I" loading logic "0" loading Output data valid delay from rising edge - - 7 3.2 4.5 - - 4 4 - - - - 15 17 0.4 - V V mA mA nS PERFORMANCE Conversion rate1 20 35 - Harmonic distortion 2 (8 MHz 2nd order harmonic) Differential gain' Differential phase' Aperture delay Aperture jitter No missing codes MCgrade MM grade Integral linearity at 25·C Adjustab!e over temp. range Differential nonlinearity at 25·C Over temp. range Power supply rejection - -40 - mega samples/sec dB - 3 1.5 8 50 - % degrees nS pS - +70 +125 +/-1 ·C ·C LSB LSB +/-0.5 +/-0.6 LSB lSB %FSR/%Vs 2-2 DESCRIPTION POWER REQUIREMENTS - - 0 -55 - +/-0.8 +/-1.0 - +/-0.3 +/-0.4 0.02 - TECHNICAL NOTES 1. Input Buffer Amplifier-Since the ADC-207 has a switched capacitor type input, the input impedance of the 207 is dependent on the clock frequency. At relatively slow conversion rates a general purpose type input buffer can be used; at high coversion rates DATEL recommends either the HA-5033, the LH-0033 or Elantec 2003.See Figure 2 for typical connections. 2.· Reference Ladder-Adjusting the voltage at + Ref adjusts the gain of the ADC-207. Adjusting the voltage at -Ref adjusts the offset or zero of the ADC-207. The midpoint pin is usually bypassed to ground through a .1uf capacitor, although it can be tied to a pFecision voltage halfway between + Ref and -Ref. This would improve integral linearity beyond 7 bits. 3. Clock Pulse Width-To improve performance at Nyguist bandwidths, the clock duty cycle can be adjusted so that the low portion of the clock pulse is 12 nseconds wide. The smaller aperature allows the ADC-207 to closely resemble an ideal sampler. CAUTION Since the ADC-207 is a CMOS device, normal precautions against static electricity should be taken. use ground straps, grounded mats, etc. The Absolute Maximum Ratings of the device MUST NOT BE EXCEEDED as irrevocable damage to the ADC-207 will occur. TIMING DIAGRAM AUTO SAMPLE AUTO SA~~LE AUTO SAMPLE ZERO N ZERO + ZERO N+2 02 MN DATA MN+1 DATA 1-1 t-I 17NS MAX 17NS MAX DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194fTEL (508) 339-3000fTLX 174388/FAX (508) 339-6356 ADC·207 ill ! OUTPUT CODING ! lillil I UiWH1W i I I ill for code changes at the midpoints between these center values shown in Table 1. For example, at the half-scale major carry, set the input to 2.54V and adjust the reference until the code flickers equally between 63 and 64. Note also that the weighting for the comparator resistor network leaves the first and last thresholds to within V. LSB of the end paints to adjustthe code transition to the proper midpoint values. (+Ref=+5.12V, -Ref=Gnd, MID POINT=no connection) NOTE: The reference should be held to 0.1% accuracy or better. Do not use the +5V power supply as a reference input without precision regulation and high frequency decoupling. Values shown here are for a 5.12Vdc reference. Scale other references proportionally. Calibration equipment should test Table 1. ADC-207 Output Coding Analog In (Center Value) Code Overflow O.OOV +0.04V +1.28V +2.52V +2.56V +2.60V +3.84V +5.08V +5.12V Zero +1 LSB +1/4 FS +1/2FS-1 LSB +1/2FS + 1/2FS + 1 LSB +3/4FS +FS . Overflow 0 0 0 0 0 0 0 0 1 - - 1 2 MSB 0 0 0 0 1 1 1 1 1 0 0 1 1 0 0 1 1 1 3 4 5 6 7 LSB Decimal Hexadecimal (incl.OV) 0 0 0 1 0 0 0 1 1 0 0 0 1 0 0 0 1 1 0 0 0 1 0 0 0 1 1 0 0 0 1 0 0 0 1 1 0 1 0 1 0 1 0 1 1 0 1 32 63 64 65 96 127 255- 00 01 20 3F 40 41 60 7F FF Note that the overflow code does not clear the data bits . • SV CHIP SELECT ClK 2 DIGITAL , VDD GROUND REF· 4 .. """ B7 BS S 11/110 . . 14 6 REF+ 83 13 1 ANALOG B GROUND 82 12 CS> cs, " B' OF 10 B7 (lS8) BO . BS The 3-state buffer has two enable lines, CS1 and CS2. Table 2 shows the truth table for chip select signals. CS1 has the function of enabling/disabling bits 1 through 7. CS2 has the function of enabling/disabling bits 1 through 7 and the overflow bit. Also a full-scale input produces all ones, including the ovel' flow bit at the output. Table 2. Chip Select Truth Table B' B2 B, (IIIISB) (N .'UF~ Figure 2. Typical Connections for Using the ADC-207 CS1 CS2 0 1 0 1 0 0 1 1 Bits 1-7 3 State Mode 3 State Mode DATA Outputed 3 State Mode Overflow Bit 3 State Mode 3 State Mode DATA Outputed DATA Outputed ORDERING INFORMATION MODEL TEMP. RANGE PACKAGE ADC-207MC ADC-207MM ADC-207/883B Oto +70 DC -55 to +125 DC -55 to +125 DC 18-pin DIP 1S-pin DIP 18-pin DIP ADC-207LC ADC-207LM ADC-207U883B to +125 DC -55 to +125 DC -55 to +125 DC o 24-pin LCC 24-pin LCC 24-pin LCC ACCESSORIES ADC-B2D7/2DS Evaluation Board (without ADC-207) For Immediate Assistance, Dial 1-800-233-2765 2-3 Contact DATEL for your Data Acquisition component needs. Dial 1..800.. 233..2765 for Applications Assistance 2-4 DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-.1194ITEL (508) 339-3000ITLX 174388/FAX (508) 339-6356 ADC-208 a-bit, 20 Msps Cmos Flash AID... FEATURES • • • • 8-Bit flash A/D converter 20 MHz sampling rate 10 MHz full-power bandwidth Sample-hold not required Low power CMOS +5V dc operation 1.2 Micron CMOS 8-Bit latched three-state outputs with overflow bit Surface mount versions MIL-STD-883B versions No missing codes ADC-208 DIP I -*0.190(4.9) GENERAL DESCRIPTION The ADC-20S utilizes an advanced VLSI 1.2 micron CMOS in providing 20 MHz sampling rates at S-bits. The flexibility of the design architecture and process delivers effective bit rates to 30 MHz in the burst mode, one shot mode conversion times of 35 nanoseconds, low power modes to 150 mW, latch-up free operation without external components and operation over the full military temperature range. The ADC-20S has 256 auto-zeroing comparators which are auto-balanced on every conversion to cancel out any offsets due to temperature and/or dynamic effects. These comparators sample the difference between the analog input and the reference voltages generated by the precision reference ladder network. Parallel output data and the overflow pin have Three-State outputs. The overflow pin allows cascading two devices for 9-bit operation. ADC-208LCC 0.060 (1,5) I ~~-~-----~..L. H~~~ ~ ~ ~ ~ ~ ~ ~ T 0190(4,9)I 0.250 ±O.005 0.05 0~. -11- r-- 0.020 ±O.005 1.250---1 (31,7) ~i~:~. ~i~~~ llEJ]' _I ~:grig t:,. (0,5) I. TOP (LCCVersion) D.400SQ, (2,5) (1,3) I D -I -+-ooso1f- ~ f-o:1oo 0.020 I 1_ 111111111111110,130 Max. t ADC-2081 [J ....L . 16 24 10 INPUTIOUTPUT CONNECTIONS PIN 1 2 3 4 5 -REFERENCE 31-"W'....oI--I6:~-, 8117 PINSID.'G~ "8 GRO~UND • ANALOG GAOUt.lO csoE"~~~-C--I)oo----~~Il-~~~~__-.J c"'~"~-----1~~~)'-'--------~ For Immediate Assistance, Dial 1·S00-233-2765 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 FUNCTION VDD CLOCK ·REFERENCE ANNDIG GND (VSS) ANALOG INPUT REFERENCE MID-POINT ANALOG INPUT ANNDIG GND (VSS) +REFERENCE VDO CS1(OUTPUT ENABLE) CS2 (OVERFLOW ENABLE) OVERFLOW BIT BIT 1 (MSB) BIT 2 BIT 3 BIT 4 REF 314 FS VDD REF 1/4 FS BIT 5 BIT 6 BIT 7 BIT 8 (LSB) 2-5 ADC·208 ABSOLUTE MAXIMUM RATINGS DESCRIPTION LIMITS UNITS Power Supply Voltage (Voo Pin 1,10,19) Digital Inputs Analog Input Reference Inputs Digital Outputs (short circuit protected to ground) Lead Temperature(10 sec) Storage Temperature -0.5 to +7.0 Vdc -0.5 -0.5 -0.5 -0.5 Vdc Vdc Vdc Vdc to to to to +5.5 +Voo+0.5 +Voo +0.5 +5.5 +300 max. -65 to +150 °C °C FUNCTIONAL SPECIFICATIONS Apply over the operating temperature range +5V, ±0.25V power supplies, 15 MHz clock, +Reference = +5V, -Reference = Ground, unless otherwise noted. ANALOG INPUTS MIN. Single-Ended,NonIsolated Input Range dc-20MHz Analog Input Capacitance (static - Pin 5 to Pin 7)-11- ----=r Ir--- r- 8-Bit 20 MHz Flash linearization +15V 19 PIN ~ NLiNV 8 NMINV 9 CLOCK 18 VIN 5 PIN FUNCTION I Reference Voltage Network For Immediate Assistance, Dial 1-800-233-2765 1 f= f= I- Converter Tri-State Buffer r--- rr--- -r - - -! - - -r - - -! - - -- 13 20 14 15 16 17 21 22 23 24 N/C +15V POWER IN CLOCK INPUT BIT4 BIT3 BIT2 BIT41 (MSB) N/C N.C. N.C. 81 82 83 84 85 86 87 88 (LS8) 3 REF. OUT +5V de 2-9 ADC·228 ABSOLUTE MAXIMUM RATINGS DESCRIPTION PARAMETERS PERFORMANCE CON'T. Power Supply Voltage (VDD Pin 1) Vcc (Pin 19) Vee (Pin 10) -0.5 to+7.0 V dc Integral Linearity +25 °C End·point Best-fit Line Over temperature End-point Best-fit Line Zero-Scale Offset (Code "0" to "1" Transition) (+25°C) (·55 to +125 °C) Gain error Full Scale Absolute Accuracy Differential Gain (2) Differential Phase (2) Aperture Delay Aperture Jitter No Missing Codes Power Supply Rejection -0.3 to + 18.0V dc +0.3 to -18.0V dc Digital Inputs (Pins 8,9,11,12,18) Analog Input (Pin 5) Digital Outputs (short circuit protected to ground) Lead Temp. (10 sec) Storage Temperature -0.5 to +5.5 V dc -0.5 to +Vdd+0.5 V dc -0.5 to +5.5 V dc +300°C -65 to +150 °C MIN TVP MAX UNITS - - ±D.5 iO.5 LSB LSB - - i1.0 ±D.75 LSB LSB - iO.5 il.0 il.0 il.0 LSB LSB LSB LSB % deg. - ·5 - ±D.5 ±D.5 ±D.5 2 1 - +10 ~~c. 50 ec. Over the operating temperature range 0.02 %FSR/%Ns Maximum - DVNAMIC PERFORMANCE FUNCTIONAL SPECIFICATIONS Apply over the operating temperature range and ±15V dc and +5V dc power supply voltages unless otherwise specified (20 MHz clock). DESCRIPTION MIN TYP MAX UNITS ANALOG INPUTS Single-Ended, Non·lsolated Input Range dc-20 MHz Analog Input Resistance Analog Input Capacitance DIGITAL INPUTS Logic Levels Logic 1 Logic 0 Logic Loading Logic 1 Logic 0 Clock Low Pulse Widths "high" "low" 0 2.45 - 2.5 5 +5.0 2.55 - - Volts Kohm pF 2.0 - - 0.8 - - 160 ·0.5 IlA 15 15 - - nSec. nSec. Vdc Vdc mA DIGITAL OUTPUTS Coding Resolution Logic Levels Logic 1 Logic 0 Logic Loading Logic 1 Logic 0 Output Data Valid Delay From Rising Edge Output Hold Time PERFORMANCE Sampling Rate (1) Differential Linearity (See Tech Note 4) (code transitions) (center of codes) 2-10 straight bin., compo bin. two's comp., compo two's compo 8 Bits - - - 0.55 Vdc Vdc - - -0.5 4 mA mA 2.4 - 30 5 - 40 - nSec. nSec. 20 - - MSPS - - ±D.5 ±D.25 LSB LSB Total Harm. Dlstort.,-O.5dB DC to 2.5 MHz 2.5 MHz to 5 MHz 5 MHz to 10 MHz Signal-te-Nolse Ratio and Distortion,O.5dB DC to 2.5 MHz 2.5 MHz to 5 MHz 5 MHz to 10 MHz Signal-to-Nolse Ratio wlo Distortion,O.5 dB DC to 2.5 MHz 2.5 MHz to 5 MHz 5 MHz to 10 MHz Effective Bits,-o.5dB DC to 2.5 MHz 2.5 MHz to 5 MHz 5 MHz to 10 MHz Input Bandwidth Full Power Bandwidth (ODb) Small Signal (-20dB) POWER SUPPL V Power Supply Range +15V dc Supply ·15V dc Supply +5V de Supply Power Supply Current +15V Supply -15V Supply +5V Supply Power Dissipation i12V, +5V Nominal Over full supply range - ·53 ·48 ·36 ·55 ·50 ·39 - ·45 ·35 ·48 ·46 ·39 - ·52 ·52 -52 -55 ·55 -55 -- FS, -dB FS, -dB FS,·dB 7.5 7.25 6.75 7.75 7.5 7 - Bits Bits Bits 10 20 - - - MHz MHz +11 ·11 +4.75 +15 ·15 +5 +15.75 ·15.75 +5.25 Volts Volts Volts - ·44 - - FS, -dB FS, -dB FS, -dB FS,·dB FS, -dB FS, -dB - - +30 +10 +230 mA mA mA - 1.4 1.5 1.6 1.75 W W - - PHVSICAL·ENVIRONMENTAL Operating Temp. Range MC MM/883B Storage Temp. Range Package Types (DIP) oto+70 °C ·55 to +125 °C -65 to +150 °C 24'pin hermetic sealed, ceramic DIP NOTES 1. At full power input and chip selects enabled. 2. For to'step, 40 IRE NTSC ramp test DATEL, Inc. 11 Cabot BOUlevard, Mansfield, MA 02048-t194fTEL (508) 339-3000fTLX 174388/FAX (508) 339-6356 nw ADC·228 _W_Jflil_ m m 1- _~gd& .iUJt TECHNICAL NOTES 74HC86 1. Rated performance requires using good high frequency techniques. The analog and digital grounds are connected internally. Avoid ground related problems by connecting the grounds to one point, the ground plane beneath the converter. Due to the inductance and resistance of the power supply return paths, return the analog and digital ground separately to the power supplies. 250 Q ~ __- - - ) OUT ~ 'VV'v-1. I::c 2. Bypass all the analog and digital supplies and the + reference (pin 3) to ground with a 4.7 j.1F, 25V tantalum electrolytic capacitor in parallel with a 0.1 j.1F cerdmic capacitor. CLOCK 100 pF 50 nSee. .. I I.. 3. DATEL uses the conservative definitions when specifying Integral Linearity (end-point) and Differential Linearity (code transition). The specifications using the less conservative definition have also been provided as a comparative specification for products specified this way. ~ t - - - - I- 4. Single conversions (one-shot mode) would require another clock edge to read out data. Users desiring to provide just a single clock pulse could use the circuit shown in Figure 2 to obtain the data. 1-- 40nSEC.-1 Figure 2. Single Clock Pulse Circuit and Operation • Use optional resistor only if op-arnp is not used to drive input. R=VEE/1.667 rnA +5V de -15V de O.Ij.lF O.Ij.lF 104~ NLiNV 8 14 15 16 NMINV 9 CSI 11 CS1 12 17 ADC-228 21 22 23 24 CLOCK 18 B1 (MSB) B2 B3 B4 B5 B6 B7 B8 (LSB) 13,20 VIN 5 ANALOG INPUT 51 NC k - - , r -_____- ,________-J-3~-r-+5VREF.OUT 19 9K 2,4,6,7 0.111F 'Optional +15Vde Figure 3. ADC-228 Typical Connections For Immediate Assistance, Dial 1-800-233-2765 2-11 ADC·228 [ I If Table 1. ADC-228 Unipolar Output Coding ANALOG INPUT +4.96V +3.75V +2.50V +1.25V +0.02V O.OOV CODE Table 2. ADC-228 Bipolar Output Coding (Assumes analog input is externally offset) STRAIGHT BIN. COMPo BIN. NMINV=O NMINV=1 NLINV=1 NLlNV=O +FS-1 LSB + 3/4 FS + 1/2 FS + 1/4 FS +1LSB ZERO 11111110 11000000 10000000 01000000 00000001 00000000 ANALOG INPUT 00000001 0011 1111 01111111 1011 1111 11111110 11111111 +2.480V +1.250V +0.020V +O.OOOV -1.250V -2.480V -2.500V CODE +FS-1 LSB +1/2 FS +1 LSB ZERO -1/2 FS -FS+1 LSB -FS TWO'S COMPo NMINV=1 NLINV=O COMPo TWO'SCOMP. NMINV=O NLINV=1 0111 1111 01000000 00000001 00000000 11000000 10000001 10000000 10000000 1011 1111 1111 1110 1111 1111 0011 1111 01111110 01111111 Table 3. Chip Select Truth Table CLOCK CS1 Pin 12 CS1 Pin 11 Bits 1-8 0 0 1 1 0 1 0 1 Three State Mode Three State Mode Data Outputted Three State Mode '-------': , :' DIGITAL OUTPUT , ," OUTPUT, _: DELAY :..- " i,j' -'mYM.T, ---til\"AO""'-;D~A;:;T:-:A--r-TM\I1\I1"'Tn'-;:D:-;-AN:;:-TA:----'M\I1\I1~"'lrCD::CA;:;T::-A----r. ~ N-l ---.., ~ ~ N+l 1"- OUTPUT HOLD TIME Figure 4. ADC-228 Timing Diagram ORDERING INFORMATION MODEL TEMP. RANGE PACKAGE ADC-228MC ADC-228MM ADC-228/883B Oto +70 °C -55 to +125 °C -55 to +125 °C 24-pin DIP 24-pin DIP 24-pin DIP Receptacle for PC board mounting can be ordered through AMP Inc., part # 3-331272-8 (component lead socket), 24 required. 2-12 DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194ITEL (508) 339-3000ITLX 174388/FAX (508) 339-6356 ADC-304 a-Bit, 20 MHz Low-Power, Flash AID FEATURES 8-Bit resolution • ± '1. LSB non-linearity • • • • 20 MHz conversion rate 8 MHz input bandwidth (-3 dB) Low-power consumption (390 mW) TTL-compatible Single or dual supply operation GENERAL DESCRIPTION DATEL's ADC-304 is an 8-bit, 20 MHz analog-to-digital flash converter. The ADC-304 offers many performance features not obtainable from other flash AID's. Key features include a low-power dissipation of 390 mW and TTL compatible outputs. A wide analog input bandwidth of 8 MHz (-3 dB) allows operation without the need of a sample-hold. Also, single +5V sUpply operation is obtainable with an input range of +3 to +5V, eliminating the need for an additional power supply. A 0 to -2 V input range is available with ±5V supply operation. MECHANICAL DIMENSIONS INCHES (mm) 1.44~~ 0.51 : (36.6 :~) g;,. 0.009 : : (0.25 : ~) (13.2:~~~ \ Le.~o~[fflftij~lo.,J" )l~ ;.~,~ Another novel feature of the ADC-304 is its user-selectable output coding. The MINV and LlNV pins allow selection of binary, complementary binary, and if external offset circuitry is used for bipolar inputs, offset binary, two's complement, and complementary two's complement coding. 0.1 -no (2.54)- -l L 0.6 (15.24) The ADC-304 is supplied in a 28-pin dual in-line package and operates over a -20°C to +75°C temperature range. Storage temperature range is from -65°C to +150°C. 0.02 (0.05 min) o.m:: -~ (4.5:~:> 0.13 (3.4 min) II: ... w . 8 . ,-Ull' !! ~ .• ;;; z 5 ~ ••'V '::. ..." ,., ,- , , , For Immediate Assistance, Dial 1-800-233-2765 Table 1. AOC-304lnputiOutput Connections Pin Function Pin Function 1 2 3 4 5 6 7 8 9 10 11 12 13 14 BIT lOUT (MSB) BIT20UT BIT30UT BIT40UT DIGGND + 5V POWER (Vcc) - 5.2V POWER (VEE) - 5.2V POWER (VEE) - 5.2V POWER (VEE) + 5V POWER (VCC) DIGGND LlNV BIT50UT BIT60UT 15 16 BIT 7 OUT BIT 8 OUT (LSB) CLOCK INPUT VRT ANAGND NO CONNECTION ANA IN NO CONNECTION ANA IN NO CONNECTION ANAGND VRB VRM MINV 17 18 19 20 21 22 23 24 25 26 27 28 2-13 ADC-304 TECHNICAL NOTES = ABSOWTE MAXIMUM RATINGS (1iI 2S"C) Supply Voltage Vcc-GND Oto +6 VEE-GND Oto -6 V V Input Voltage (analog) Vin (Dual Power Supply) VEE to ANA GND +0.3 V Input Voltage (reference) VRT. VRs. VRM (Dual Power Supply) VEE to ANA GND +0.3 V 2.5 V I VRT-VRs I IVRM -3.0 to +3.0 rnA -0.5 to vee Digital Inputs V Input Current Input Voltage 1. DIG GND pins (5 and 11) and Vce pins (6 and 10) connect to separate internal circuits within the ADC-304. Connect these pins to their respective PCB patterns. 2. Layout of the analog and digital sections should be separated to reduce interference from noise. To further guard against unwanted noise, it is recommended to bypaSs, as close as possible. the voltage supply pins (6.10) to their respective ground pins (5,11) with a 1 p.F and a 0.01 p.F ceramic disk capacitor in parallel. FUNCTIONAL SPECIFICATIONS Unless otherwise noted, the following specifications apply to the ADC-304 when used either with a single or dual power source. The test conditions are: 3. The input capacitance of the analog input is much smaller than that of a typical Flash AID Converter. It is necessary to use an amplifier with sufficient bandwidth and driving power. The analog input pins (21.23) are separated internally, so they should be connected together externally. If the ADC-304 is driven with a low- output impedance amplifier. parasitic oscillations may occur. For Single Power Supply Operation: Vee (Pins 6 + 10) = +5V, DIG GND = OV VEE (Pins 7. 8 + 9) = OV. VRT (Pin 18) = +5V VR. (Pin 26) = +3V, Ta = 25°C ANA GND (Pins 19 + 25) = + 5V For Dual Power Supply Operation: Vee (Pins 6 + 10) = +5V,DIGGND(Pins5 + 11) = OV ANA GND = OV, VEE = -5V VRT(Pin18) = OV, VR. (Pin 26) = -2V Ta = 25°C DESCRIPTION Inputs Analog Input Range ............... Input Capacitance . . . . . . . . . . Input Bias Current .. , ....... Offset Voltage: MIN_ TYP_ MAX_ UNITS VRT - 30 50 35 100 V pF p.A (VRB) ................... 8 0 13 5 19 11 mV mV Digital Logic Levels: LogiC "1" ................ Logic "0" ................ Logic Input Currents : Logic "1" ................ Logic "0" ................ - - 0.8 V V 0 -0.5 p.A mA (VRT) ................... VRB 2.0 -100 -0.32 Outputs Resolution Output Coding Logic levels: Logic "1" ................ Logic "0" ................ Logic Level Loading: Logic "1" ................ Logic "0" ................ Output Data Delay (TDLH) .................. (TDHL) .................. 2-14 8 Straight Binary Complementary Binary 2's Complement Complementary 2's Complement 2.7 - 3.4 Bits V V - 0.5 -500 3 p.A mA 30 35 nSec. nSec. - 25 26 These parasitic oscillations can be prevented by introducing a small resistance of 2 to 10Q between the amplifier output and the ADC-304's AID input. This resistance must be of very low value of inductance at high frequencies. Note that each of the analog input pins are divided in this manner with these resistances. Connect the driving amplifier as close as possible to the AID input of the ADC-304. 4. The voltage between VAT (pin 18) and VAB (pin 26) is equivalent to the dynamic range of the analog input. Bypass VAB to ANA GND (pins 19 and 25) by means of a lp.F and 0.01 p. F capacitor in parallel. To balance the characteristics of the ADC-304 at high frequencies. bypass VAM (pin 27) with a 0.01p. F capacitor to ANA GND (pins 19 and 25). Also. VAM (pin 27) can be used as a trimming pin for more precise linearity compensation. A stable voltage source with a potential equal to -FSA and a 1 KQ potentiometer can be connected to VAM (pin 27) as shown in Figure 3 for this purpose. 5. Separate the clock input. CLK (pin 17). from other leads as much as possible. observing proper EMI and AFI wiring techniques. This will reduce the inductive pick-up of this lead from interfering with the "clean'" operation of the ADC-304. . DATEL. Inc. 11 Cabot Boulevard, Mansfield. MA 02048-11941TEL (508) 339-30001TLX 174388/FAX (508) 339-6356 ADC·304 Performance MIN. 20 Conversion Rate 1 . • . • • • • • • . . Non-Linearity .... .. .. .. .... Differential Non-Linearity ..... Differential Gain Error' ....... Differential Phase Error 2 ..... Aperture Delay .............. Aperture Jitter .............. Clock pulse width: Tpw1 ... TpwO ..... Reference Pin Current ....... Reference Resistance (VRTto VRB) Reference Input (Dual Supply) (VRT) ................... (VRB) ................... 5 - 35 10 " - -0.1 -1.8 TYP. - MAX. UNITS - MHz LSB lSB ±1/2 ±1/2 1.5 0.5 9 % 15 130 -18 - Degrees nSec. pSec. nSec. nSec. mA ohms 0 -2.0 +0.1 -2.2 V V 7 30 - Power Supply Requirements Single Power Supply Supply voltage (Vee) ................... (VEE) .. .. .. .. .. .. ....... Supply Current: (ICC + lEE) .............. Power Dissipation ........... 4.75 - Dual Power Supply Supply Voltage: (Vee) ................... (VEE) .. .. .. .. .. .. .. .. .. . Supply Current (ICC) ................... (lEE) ...... -,- .......... Power Dissipation ..... , ..... -0 - 5.25 V V 71 360 88 442 mA mW 4.75 -4.75 5.0 -5.2 5.25 -5.5 V V - 10 62 390 14 75 440 mA mA mW -20 -55 - +75 +150 ·C ·C TECHNICAL NOTES (CONT.) 6. The analog input signal is sampled on the positive-going edge of ClK. Corresponding digital data appears at the output on the negative-going edge of the ClK pulse after a small delay of 35 nSec. maximum (TDlH, TDHl). Refer to the Timing diagram, Figure 4, for more information. 7. Connect all free pins to ANA GND (pins 19 and 25) to reduce unwanted noise. The analog input range is equal to a 2V spread. The voltage on VRT-VRB will equal 2V. The connection of VRT and ANA GND is 2V higher than VRB. Whether using a single or dual power supply, the analog input will range from the value of VRT to VRB. If VRT equals +5V, then VRB will equal +:N and the analog input range will be from +5 to +:N. SINGLE SUPPLY OPERATION ADC·304 Physical/Environmental Operating Temperature ....... Storage Temperature ........ 1. 2. fin = 1 KHz, ramp NTSC 40 IRE·modulated ramp, Fe = 14.3 MSPS 0.01 Analog Input ~ m J~~ Clock Output &8it latch Output Data OutpUT Bits 1-8 ~ iI : ~:' ~ I Comparator I I I iI II X N·1 Data valid : X : I-- --tTDLH r-- I I I 1,35nSj_1 "---- DUAL SUPPLY OPERATION ADC·304 I I II I : N Data valid: -jTDHL T"' X: : N + 1 Data Valid lK I I I I I 1· 35n j"1 I Figure 2: ADC·304 Timing Diagram I Figure 3: Improving Linearity Compensation For Immediate Assistance, Dial 1-800-233-2765 2-15 ADC-304 Table 2. Output Coding for + 5V Power Supply Operation (+5 to +3V Signal Input) Unipolar Scale +FS-1LSB +%FS +¥.FS +1I2FS +V4 FS +'A.FS +1 LSB Zero MINV LINV +4.9922V +4.7500V +4.5000V +4.0000V +3.S000V +3.2500V +3.0078V +3.0000V Straight Binary Complement 2'. 0 0 0 1 10000000 10100000 11000000 00000000 01000000 00100000 01111110 01111111 11111111 11011111 10111111 01111111 00111111 00011111 00000001 00000000 2's Complement Complement Binary 1 1 Complement 0 01111111 01011111 00111111 11111111 10111111 11011111 10000001 10000000 1 00000000 00100000 01000000 10000000 11000000 11100000 11111110 11111111 Table 3. Output Coding for ± 5V Power Supply Operation (0 to - 2V Signal Input) Straight Binary Unipolar Scale 0 -1 LSB -'A.FS -V. FS -lhFS -%FS -%FS -FS+1LSB MINV 0 0 LlNV OV -7.813mV -250.00mV -SOO.OOmV -1.0V -1.5V -1.7SV -1.9922V 11111111 11111110 11011111 10111111 01111111 00111111 00011111 00000000 2'8 Complement 2's Complement Binary Complement Complement 1 1 0 1 1 0 10000000 01111111 00000000 00000001 10000001 01111110 10100000 01011111 00100000 00111111 01000000 11000000 11111111 10000000 00000000 10111111 11000000 01000000 00100000 11011111 11100000 01111111 11111111 10000000 APPLICATION CIRCUITS (MSBI (MSB) Analog input Analog input Oto -2V +5to +3V ITTL level) ITTL level! ITTL level! l (TTL level! B'150---+--+-( ....1 ,i.SB1 Figure 5: Connections for +5V Figure 6: Connections for ±5V Power Supply Operation Power Supply Operation ORDERING INFORMATION 2-16 MODEL DESCRIPTION ADC-304 8-bit, 20 MHZ, Low-power, flash AID DATEL, Inc. 11 Cabot BOUlevard, Mansfield, MA 02048-1194rrEL (508) 339-3000rrLX 174388/FAX (508) 339-6356 ADC-500, ADC-505 12-Bit, Ultra-Fast, Low-Power AID Converters FEATURES • • • • • • • • 12-8it resolution 500 Nanosecond maximum conversion time Low-power, 1.6W Small initial errors Three-state output buffers -55°C to +125°C operation Small 32-pin DIP No missing codes MAX~ l.....--'.101 (28,01 I- GENERAL DESCRIPTION DATEL's ADC·500 and ADC-505 are 12·bit analog·to·digital converters which have small initial errors and can also provide adjustment capability for system errors. Both models have identical specifications except for conversion times. The ADC·505 has a maximum conversion time of 550 nanoseconds while the ultra-fast ADC-500 accomplishes .a 12-bit conversion in less than 500 nanoseconds. Figure 1 is a simplified block diagram applicable to both devices. Manufactured using thick-film and thin-film hybrid technology, these converters' remarkable performances are based upon a digitallY'corrected subranging architecture, DATEL further enhances this technology by using a proprietary custom chip and unique laser trimming schemes. The ADC-500 and ADC-505 are packaged in a 32-pin ceramic DIP and consume 1.6 watts. ~~~--~--1-+----------' OffSET ""'" ,ow ""'" -.. For Immediate Assistance, Dial 1-800-233-2765 - I IL 0.150 (3.8) MIN J. I --I...- I 0.190 (4,91 MAX 1t 0.010 l( 0.018 Kovar 116 17 ~T T I .1':; :. :.I __ . MECHANICAL DIMENSIONS INCHES (mm) 1.712 MAX ~ BOTTOM VIEW I I 11 32 '~'"' stand off from case m 0.100 ....,.-----.....,,...--0 I~ r-- 0900 (22,91 .. I.. 0.100 (2.5) INPUT/OUTPUT CONNECTIONS PIN SIGNAL NAME 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 +lOV REF RANGE INPUT HIGH INPUT LOW OFFSET ADJUST NO CONNECTION COMP BIN OVERFLOW ENABLE (6-12) ENABLE (1-5. O.F.) +5V DIGITAL GROUND +15V -15V -5V ANALOG GROUND SfHCONTROl EOC BIT 12 (LSB) BIT 11 BIT 10 BIT9 BIT8 BIT 7 BIT6 BITS BIT4 BIT 3 BIT2 BIT 1 (MSBI START CONVERT GAIN ADJUST 2-17 ADC.SOO, ADC·SOS Another novel feature of the ADC-500 is the provision of a SamplelHold control pin for applications where a sample-hold is used in conjunction with the ADC-500. This feature allowsthesample-andhold device to go back into the sample mode a minimum of 30 nanoseconds before the conversion is complete, improving the overall conversion rate of the system. ABSOLUTE MAXIMUM RATINGS Parameters MINIMUM + lSV Supply (Pin 13) .. . 0 -lSV Supply (Pin 14).. . 0 +SVSupply(Pinll).... -0.5 - SV Supply (Pin 15) .. .. + 0.5 Digital Inputs (Pins7,9,10&31) ... -0.3 Analog Input (Pin 3) .... - 15 Lead temp. (10 sec) ... . MAXIMUM +18 -18 +7 UNITS Volts dc Volts dc Volts dc Volts dc +6 +15 300 Volts dc Volts dc -7 ·C FUNCTIONAL SPECIFICATIONS Apply over the operating temperature range and at ±15V dc and ±5V dc unless otherwise specified. DESCRIPTION MIN. TYP. MAX. UNITS INPUTS Input Voltage Range ... (See Tech. Note 9) Logic Levels: Logic 1 .. Logic 0 .. Logic Loading: Logic 1 Logic 0 - 2.0 -- o to +10 o to +20 ±10 - - 0.8 2.5 -100 Volts dc Volts dc Volts dc Volts dc Volts dc p.A p.A OUTPUTS Output Coding: (Pin 7 High) ........ (Pin7Low) ........ Logic Levels: Logic 1 .. 2.4 Logic 0 .. Logic Loading: Logic 1 Logic 0 Internal Reference: VoHage, +25·C .... 9.98 Drift .............. External Current .... - straight binary/offset binary comPlementa:k binary complementary 0 set binary Volts dc 0.4 Volts dc -160 p.A 6.4 rnA - - 10.0 ±5 - - 10.02 ±30 1.5 Volts dc ppm/·C rnA PERFORMANCE Integral Nonlinearity: +2S·C ...........• O·C to + 70·C ...... -SS·Cto +12S·C .. Integral Nonlin. Tempco. Differential Nonlinearity +25·C ............ O·C to + 70·C ...... -SS·Cto + 12S·C .. Differential Nonlin. Tempco ........... Full-Scale Absol. Accuracy: +2S·C ............ O·C to + 70·C ...... -SS·Cto + 12S·C .. 2-18 -- -- - - ±3 - - ±0.0125 OfoFSR ± V2 LSB ±0.0125 OfoFSR ± V2 LSB ±0.0125 OfoFSR ± 3 LSB ppm/·C ±8 ±0.0125 OfoFSR ±V2 LSB ±0.0125 OfoFSR ±'/2 LSB ±0.0125 OfoFSR ±1 LSB - - ±2.5 ppm/·C - ±3 ±4 ±8 ±8 ±14 ±29 LSB LSB LSB - PERFORMANCE (cont.) DESCRIPTION Unipolar Zero Error, +2S·C ............. Unipolar Zero Tempco .. Bipolar Zero Error, +2S·C ............. Bipolar Zero Tempco ..• Bipolar.Dffset Error, +2S·C ............. Bipolar Offset Error Tempco ............ Gain Error, + 2S·C ..... Gain Tempco .......... Conversion Times: ADC-SOO +2S·C ........... O·C to + 70·C ..... - 55·C to + 12S·C ADC-SOS +2S·C ........... O·C to + 70·C ..... -SS·Cto +125·C .. MIN. TYP. MAX. UNITS - - ±1 ±13 ±3 ±25 LSB ppm/·C - ±1 ±13 ±3 ±25 LSB ppm/oC --- Harm. Distort. (-FS) ill +25°C Oto +70 °C -55 to +125 °C No Missing Codes (12 Bits): ............ ±2 ±5 LSB ±17.5 ±2 ±17.5 ±35 ±5 ±35 ppm/·C LSB ppm/·C 500 540 560 550 590 620 nsec. nsec. nsec. - - nsec. nsec. nsec. -72 dB min. -72 dB min. -65 dB min. Over the Operating Temp. Range POWER SUPPLY REQUIREMENTS Power Supply Range: + 15V dc Supply ...•. -lSV dc sUP~IY ..... +SVdcSuppy ...... - 5V dc Supply ...... Power Supply Current: +lSVSupply ........ -lSVSupply ..•..... +SVSupply· ........ -SVSupply ......... Power Dissipation ...... Power Supply Rejection. +14.25 -14.25 +4.75 -4.75 +15 -15 +5 -5. +15.75 -15.75 +5.25 -5.25 -- +23 -11 +55 -175 1.6 +30 -15 +90 -210 1.8 0.D1 - - Volts Volts Volts Volts dc dc dc dc rnA mA rnA rnA Watts OfoFSR/oAlV PHYSICAL/ENVIRONMENTAL Operating Temp. Range: -BMC ............. 0 +70 -BMM ............. -55 + 125 Storage Temperature Range .............. -65 +150 Package Type ......... 32-pin hermetic sealed, ceramic Pins ................. 0.010 x 0.018 inch Kovar Weight ............... 0.42 ounces (12) grams - ·C ·C ·C DIP • + 5V power usage at 1TIL logic loading per data output bit. CD With DATEL sample and hold model number SHM-45. TECHNICAL NOTES 1 . Use external potentiometers to remove system errors or the small initial errors to zero. Use a 20K trimming potentiometer for gain adjustment with the wiper tied to pin 32 (ground pin 32 for operation without adjustments). Use a 20K trimming potentiometer with the wiper tied to pin 5 for zer%ffset adjustment (leave pin 5 open for operation without adjustment). 2. Rated performance requires using good high frequency circuit board layout techniques. The analog and digital grounds are not connected internally. Avoid ground-related problems by connecting the digital and analog grounds to one pOint, the ground plane beneath the converter. Due to the inductance and resistance of the power supply return paths, return the analog and digital ground separately to the power supplies. DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194ITEL (508) 339-3000ITLX 174388/FAX (508) 339-6356 ADC·SOO, ADC·505 3. Bypass all the analog and digital supplies and the + 1OV reference (pin 1) to ground with a 4.7 IlF, 25V tantalum electrolytic capacitor in parallel with a 0.1 IlF ceramic capacitor. Bypass the + 1OV reference (pin 1) to analog ground (pin 16). The -5V dc supply is treated as an analog supply and analog ground (pin 16) should be treated as its return path for decoupling purposes. 4. Obtain straight binary/offset binary output coding by tying COMP BIN (pin 7) to +5V dc or leaving it open. The device has an internal pull-up resistor on this pin. To obtain complementary binary or complementary offset binary output coding, tie the COMP BIN pin to ground. The COMP BIN signal is compatible-to CMOS/ TTL logic levels for those users desiring logic control of this function. 8. Over temperature, input capacitance is 50 pF maximum and input impedance is 1.75K minimum (2.5K typical) for unipolar and 3.75K minimum (5K typical) for bipolar. These values are guaranteed by design. 9. Requirements for ±2.5V inputs can be satisfied using DATEL's AM-1435 amplifier in front of the SHM-45/ADC-500 configuration, shown in Figure 3, at the appropriate gain. The SHM-45's gain of 2 mode allows 0 to +5V or ±5V input ranges. TIMING Figure 2 shows the relationship between the various input signals. The timing cited applies over the operating temperature range and over the operating power supply range. These times are guaranteed by design. 5. An overflOW signal, pin 8, indicates when analog input signals are below or above the desired full-scale range. To overflow pin also has a three-state output and is enabled by pin 10 (Enable bits 1-5 &O.F.). TABLE 2. INPUT CONNECTIONS 6. The Sample/Hold control signal, pin 17, goes low following the rising edge of START QQt::IVERT pulse and high 30 nanoseconds minimum before EOC goes low. This indicates that the converter can accept a new analog input. INPUT PIN 010 +10Vdc 3 CONNECT PIN 2 (RANGE) TO PIN: 3 o to +20V de 3 16 ±10V de 3 1 TABLE 3. ZERO AND GAIN ADJUST 7. The drive requirements of the ADC-500/505 may be satisfied with a wide-bandwidth, low output impeance input source. Applications of these converters that require the use of a sample-hold may be satisfied by using DATEL's model SHM-45. Using this device with multiplexers or for test purposes will require an input buffer. ANALOG INPUT VOLTAGE RANGE. FSR ZERO ADJUST +1/2 LSB GAIN ADJUST +FS -1 1/2 LSB oto +10V dc oto +20V dc +1.22 mV +2.44 mV +2.44 mV +9.9963Vdc +19.9927Vdc +9.9927Vdc ±10Vdc • INPUT~ --------,,---------------------------------------,, , AI%~~~G ,, , -t- ~~~~~~ ------'L'__________________________________________ SETTliNG TIME I START I : I I I , I 105nSec MINIMUM (when used with SHM-45) I CONVERT ; JJI ~-, , I I : ,, , "H- ' I I I I I I I I I I !t: !, , I I 'I' 'I I :-t-i -----+'I --..; I I IDOnSer. HOLDMOOES[TTLINGTIME , H- I ~ NOTE NOT DRAWN TOSCAL[ 200 "Sec ACQUISITION TIME I I II CONVERSION TIME r-----~---------------------~ 20nSec MINIMUM 35nSec MAXIMUM I I I i I --.Ji-:----------+i-,\ i I , i! : ! , , f-! I I: -j, EOC ---T,----------------------------------------- !-, ---j 10nSE.'C MINIMUM 25nSsc MAXIMUM I i S/H 1--1----------- ~~,';.!': OUTPUT DATA DATA N·1 VALID ENABLED OATA N·l VALID (BITS l·S.OF) ENABLED DATA N·' VALID (BrT$6·,2j I -------------1 30nSeL MINIMUM f-- i ,,, -j ~ IOnSec MAXIMUM 10nSec MAXIMUM r- 25nSec MINIMUM DATANVALIO FLED DATA N VALID ~LEDDATAN VALID 'NVAUO OATA ~ Figure 2. ADC-500/505 and SHM-45 Timing Diagram For Immediate Assistance, Dial 1-800-233-2765 2-19 ADC-SOO, ADC-50S CALIBRATION PROCEDURE flickers equally between 0000 0000 0000 and 0000 0000 0001 with the COMP BIN (pin 7) tied high or between 1111 1111 1111 and111111111110withtheCOMPBINtiedlow. Removal of system errors or the small initial errors is accomplished as follows: 1. Connect the converter per Figure 3 and Table 2 for the appropriate full-scale range (FSR). Apply a pulse of 50 nanoseconds minimum to the START CONVERT input (pin 31) at a rate of 500 KHz. This rate chosen to reduce flicker if LED's are used on the outputs for calibration purposes. 3. Full-Scale Adjustment - Set the output of the voltage reference used in step 2 to the value shown in Table 3. Adjust the gain trimming potentiometer so that the output code flickers equally between 1111 1111 1110 and 1111 1111 1111 for COMP BIN (pin 7) tied high or between 0000 0000 0001 and 0000 0000 0000 for COMP BIN tied low. 2. Zero Adjustments - Apply a precision voltage reference source between the analog input (pin 3) and ground (pin 16). Adjust the output of the reference source per Table 3. For unipolar, adjust the zero trimming potentiometer so that the output code 4. To confirm proper operation of the device, vary the precision reference voltage source to obtain the output coding listed in Table 4. TABLE 4. OUTPUT CODING STRAIGHT UNIPOLAR INPUT RANGES, V de SCALE +FS -1 LSB 7/8 FS 314 FS 112 FS 1.14 FS 118 FS 1 LSB 0 oto +10V oto +20V +9.9976V +8.7500V +7.5000V +5.0000V 2.5000V 1.2500V 0.0024V O.OOOOV BIN CaMP BINARY OUTPUT CODING MSB LSB +19.9951V 1111 1111 1111 +17.500V 111000000000 +15.000V 1100 0000 0000 +10.000V 1000 0000 0000 +5.0000V 0100 0000 0000 +2.5000V 0010 0000 0000 +0.0049V 0000 0000 0001 O.OOOOV 0000 0000 0000 OFF. BINARY INPUT RANGE BIPOLAR MSB LSB 0000 0000 0000 0001 1111 1111 0011 1111 1111 011111111111 10111111 1111 110111111111 1111 1111 1110 1111 1111 1111 CaMP +10Vde +9.9951 V +7.5000V +5.0000V O.OOOOV -5.0000V -7.5000V -9.9951 V -10.000V SCALE +FS -1 LSB +3/4 FS +1/2 FS 0 -1/2 FS -3/4 FS -FS +1 LSB -FS OFF. BIN +15V de ADC-500/505 ORDERING INFORMATION MODEL NO. OPERATING TEMP. RANGE SEAL ADC-500BMC ADC-500BMM ADC-500BMC ADC-500 BMM Oto+70°C -55 to +125 °C Oto+70°C -55to+125°C Hermetic Hermetic Hermetic Hermetic -15V +15V OfFSET ADJUST Figure 3. ADC-SHM Connection Diagram Receptable for PC board mounting can be ordered through AMP Incorporated, #3-331272-8 (Component Lead Socket), 32 required. 2-20 DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194ITEL (508) 339-3000ITLX 174388/FAX (508) 339-6356 ADC-508 12-Bit, Ultra-Fast, Low-Power AID Converter FEATURES • 12-8it resolution 700 Nanosecond maximum conversion time • Low-power,1.6W • Small initial errors • Three-state output buffers -55°C to +125°C operation • Small 32-pin DIP No missing codes GENERAL DESCRIPTION DATEL's ADC-508 is a 12-bit, analog-to-digital converter which has small initial errors and can also provide adjustment capability for system errors. The ADC-508 has a maximum conversion time of 700 nanoseconds. Figure 1 is a simplified block diagram. Manufactured using thick-film and thin-film hybrid technology, this converter's remarkable performance is based upon a digitally-corrected subranging architecture. DATEL further enhances this technology by using a proprietary custom chip and unique laser trimming schemes. The ADC-508 is packaged in a 32-pin ceramic DIP and consumes 1.6 watts. ~11~8~~X-j ~ I 10.,90 (4,9) MAX IL 1t . .'" "".. ~,". ~'";-' T,J_ ~~'='~:::'''"' Be;r;~M al.'g:f~;o:, ~o ' I I 11 I NOTE: Pins have 0.025 inch. ± 0.01 stand off from case 32 I.. '-:-------:-' --0 I~ 0900 r--(22.9) .. 0.100 (2.5) INPUT/OUTPUT CONNECTIONS PIN 1 2 3 4 5 6 ,.g:~f €,"!I---I~-j-+------; Of"FSET "DJUSl .... BiN 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 For Immediate Assistance, Dial 1-800-233-2765 SIGNAL NAME +1DV REF RANGE INPUT HIGH INPUT LOW OFFSET ADJUST NO CONNECTION COMPBIN OVERFLOW ENABLE (6-12) ENABLE (1·5. OF) +5V DIGITAL GROUND +15V -15V -5V ANALOG GROUND SIHCONTROL EOC BIT 12 (LSB) BIT 11 BIT 10 BIT9 BIT 8 BIT7 BIT6 BIT 5 BIT4 BIT3 BIT2 BIT 1 (MSB) START CONVERT GAIN ADJUST 2-21 Another novel feature of the ADC-508 is the provision of a Sampie/Hold control pin for applications where a sample-hold is used in conjunction with the ADC-508. This feature allows the sample-andhold device to go back into the sample mode a minimum of 30 nanoseconds before the conversion is complete, improving the overall conversion rate of the system. Power required is ± 15V de and ± 5V dc. Models are available in the. commerc;ial O·C to + 70°C, and military - 55°C to + 125°C operating temperature range. Typical applications include spectrum, transient, vibration, and waveform analysis. These devices are also ideally suited for radar, sonar and video digitization, medical instrumentation, and high-speed data acquisition systems. For information ABSOLUTE MAXIMUM RATINGS MINIMUM Parameters + ISV Supply (Pin 13) ... 0 -ISV Supply (Pin 14) ... 0 + SV Supply (Pin 11) .... -0.5 - SV Supply (Pin 1S) .... +0.5 DI~itallnputs Pins7,9,10&31) ... Analog Input (Pin 3) ...• Lead temp. (10 sec) ...• MAXIMUM +18 -18 +7 -7 UNITS Volts de Volts de Volts de Volts de +6 +15 300 Volts de Volts de ·C -0.3 -15 FUNCTIONAL SPECIFICATIONS Apply over the operating temperature range and at ±15V de and ±5V de unless otherwise specified. DESCRIPTION MIN. TYP. -- Oto +10 o to +20 ±10 - - MAX. UNITS INPUTS Input VOlta~e Range ... (See Tec . Note 9) Logic Levels: Logic 1 ., 2.0 Logic 0 .. Logic Loading: Logic 1 • LogicO. - - 0.8 2.5 -100 Volts Volts Volts Volts Volts de de de de de ,.A ,.A OUTPUTS Output Coding: (Pin 7 High) ........ (Pln7Low) ........ Logic Levels: logic 1 .. 2.4 Logic 0 .. Logic Loading: Logic 1 . LogicO. Internal Reference: Voltage, +2S·C •••• 9.98 Drift .............. External Current ..•. - straight binary/offset binary complementary binary complementary offset binary Volts de 0.4 Volts de -160 ,.A 6.4 mA - - 2-22 MIN. Unipolar Zero Error, +2S·C ............. Unipolar Zero Tempeo .. Bipolar Zero Error, +25·C ............. Bipolar Zero Tempeo ... Bipolar Offset Error, +2S·C ............. Bipolar Offset Error Tempeo ............ GalnError, +2S·C ..... Gain Tempeo .......... Conversion Times: ADC-508 +25·C ........... O·C to + 70·C ..... Harm. Distort. (-FS) ill +25'C Oto +70 'C No Missing Codes (12 Bits): ............ - TYP. MAX. UNITS ±1 ±13 ±3 ±25 LSB ppm/·C ±1 ±13 ±3 ±25 LSB ppm/·C - ±2 ±5 LSB - ±17.5 ±2 ±17.5 ±35 ±5 ±35 ppm/·C LSB ppm/·C 700 740 nsee. nsee. -- - - ·72 dB min. ·72 dB min. Over the Operating Temp. Range POWER SUPPLY REQUIREMENTS Power Supply Range: + ISV dc Supply ..... -1SV dc SUP~IY ..... +SVdcSuppy ...... - SV dc Supply ...... Power Supply Current: + ISV Supply ........ -1SV SUP~IY ........ +SVSuppy· ........ -SVSupply ......... Power DIssipation •..... Power Supply Rejection . +14.25 ":14.25 +4.75 -4.75 +15 -15 +5 -5 +15.75 -15.75 +5.25 -5.25 -- +23 -11 +55 -175 1.6 +30 -15 +90 -210 1.8 0.01 - - Volts Volts Volts Volts de dc de de mA mA mA mA Watts %FSR/%V PHYSICAUENVIRONMENTAL Operating Temp. Range: ·C -BMC ............. 0 +70 Storage Temperature ·C +150 Range .............. -65 Package Type ......... 32·pin hermetic sealed, ceramic DIP Pins ................. 0.010 x 0.018 inch Kovar Weight ............... 0.42 ounces (12) grams - • +5V power usage at lITL logic loading per data output bit. (j) With DATEL sample and hold model number SHM-45. - 10.0 ±5 - 10.02 ±30 1.5 Volts de ppm/·C mA PERFORMANCE Integral Nonlinearity: +2SoC ............ O·Cto +70·C ....•. IntegraiNonlin. Tempco. Differential Nonlinearity +2S·C ............ O·Cto + 7O·C ...... Differential Nonlin. Tempeo ..•........ Full-Scale Absol. Accuracy: +2SoC ............ O·C to + 7O·C ...... PERFORMANCE (cont.) DESCRIPTION -- ±3 - ±0.0125 %FSR ± 11z LSB ±0.0125 oAlFSR ± 11z LSB ppm/·C ±8 - - ±0.0125 %FSR ±V2 LSB ±0.0125 %FSR ±V2 LSB - - ±2.5 ppm/·C - ±3 ±4 ±8 ±14 LSB LSB - TECHNICAL NOTES 1 . Use external potentiometers to remove system errors or the small initial errors to zero. Use a 20K trimming potentiometer for gain adjuslment with the wiper tied to pin 32 (ground pin 32 for operation without adjustments). Use a 20K trimming potentiometer with the wiper tied to pin 5 for zer%ffset adjustment (leave pin 5 open for operation without adjustment). 2. Rated performance requires using good high frequency circuit board layout techniques. The analog and digital grounds are not connected internally. Avoid ground-related problems by connect ing the digital and analog grounds to one point, the ground plane beneath the converter. Due to the inductance and resistance of the power supply return paths, return the analog and digital ground separately to the power supplies. DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194ITEL (508) 339-3000ITLX 174388/FAX (508) 339-6356 ADC·508 3. Bypass all the analog and digital supplies and the + 1OV reference (pin 1) to ground with a 4.7 /!F, 25V tantalum electrolytic capacitor in parallel with a 0.1 /!F ceramic capacitor. Bypass the + 1OV reference (pin 1) to analog ground (pin 16). The -5V dc supply is treated as an analog supply and analog ground (pin 16) should be treated as its return path for decoupling purposes. 4. Obtain straight binary/offset binary output coding by tying COMP BIN (pin 7) to +5V dc or leaving it open. The device has an internal pull-up resistor on this pin. To obtain complementary binary or complementary offset binary output coding, tie the COMP BIN pin to ground. The COMP BIN signal is compatible to CMOS/ TTL logic levels for those users desiring logic control of this function. 5. An overflow signal, pin 8, indicates when analog input signals are below or above the desired full-scale range. To overflow pin also has a three-state output and is enabled by pin 10 (Enable bits 1-5 &O.F.). 8. Over temperature, input capacitance is 50 pF maximum and input impdeance is 1. 75K minimum (2.5K typical) for unipolar and 3.75K minimum (5K typical) for bipolar. These values are guaranteed by design. 9. Requirements for ±2.5V inputs can be satisfied using DATEL's AM-1435 amplifier in front of the SHM-45/ADC-508 configuration, shown in Figure 3, at the appropriate gain. The SHM-45's gain of 2 mode allows 0 to +5V or ±5V input ranges. TIMING Figure 2 shows the relationship between the various input signals. The timing cited applies over the operating temperature range and over the operating power supply range. These times are guaranteed by design. TABLE 2. INPUT CONNECTIONS INPUT VOLTAGE RANGE INPUT PIN Oto +10Vdc 3 3 010 +20Vdc 3 16 ±10V de 3 1 6. The Sample/Hold control Signal, pin 17, goes low following the rising edge of START COOVERT pulse and high 30 nanoseconds minimum before EOC goes low. This indicates that the converter can accept a new analog input. CONNECT PIN 2 (RANGE) TO PIN: TABLE 3. ZERO AND GAIN ADJUST 7. The drive requirements of the ADC-508 may be satisfied with a wide-bandwidth, low output impeance input source. Applications of these converters that require the use of a sample-hold may be satisfied by using DATEL's model SHM-45. Using this device with multiplexers or for test purposes will require an input buffer. ANALOG INPUT ANALOG INPUT SETTLING TIME 1 1 l : I I 1 : ! to +10V dc to +20V dc ±10V dc +1.22 mV +2.44 mV +2.44 mV +9.9963Vdc +19.9927Vdc +9.9927Vdc o o I I I 105nSec MINIMUM JJI ~-I : I' : I: -1 : 1-: 'rt--::I I I I I I I I I lt I: I I roc ___;.I_-l Ii-I 1 1 I I ~I__, I CONVERSION TIME 20 nS!l1: MINIMUM I H- NOTE NOT ORAWN TO SCALE 200nSec ACOutSITIONTIME '.I :: II l00n$ecHOLDMODESETTUNGTIME I I :1 __________ i (when used with SHM-45) ~,---+:------------------------------------------ i 1 I ~~ GAIN ADJUST +FS -11/2 LSB 150nSec; - - - - , ! -________________________________________ I --It - MINIMUM __ START ;.- ZERO ADJUST +1/2 LSB ~ , --------~,------------------------------------------- I CONVERT FSR 3S nSec MAXIMUM 10 nSec MINIMUM ----l 2SnSec MAXIMUM 1 Ii~·rl--------------------------------~I :, 1------------OUTPUT DATA :.:;,.S: - - - - - - - - 1·1 DATAN-l VALID 10nSec. MAXIMUM ENABLED OATA N·1 VALID (BITS6-12j 10nSae. MAXIMUM f-1 1 1 1 -j J--- M)@(l ENABLED DATA N-1 VALID (BITS 1-5.0F) 30nSe<: MINIMUM 25n58(:. MINIMUM OATANVALJD ~LEOOATAN VALID ~LEDDATAN VALID 'NVALIO DATA [8] Figure 2. ADC-508 and SHM-45 Timing Diagram For Immediate ASSistance, Dial 1-800-233-2765 2-23 ADC·S08 CALIBRATION PROCEDURE flickers equally between 0000 00000000 and 0000 0000 0001 with the COMP BIN (pin 7) tied high or between 1111 1111 1111 and111111111110withtheCOMPBINtiedlow. Removal of system errors or the small initial errors is accomplished as follows: 3. Full-Scale Adjustment - Set the output of the voltage reference used in step 2 to the value shown in Table 3. Adjust the gain trimming potentiometer so that the output code flickers equally between 1111 1111 1110 and 1111 1111 1111 for COMP BIN (pin 7) tied high or between 0000 0000 0001 and 0000 0000 0000 for COMP BIN tied low. 1. Connect the converter per Figure 3 and Table 2 for the appropriate full-scale range (FSR). Apply a pulse of 50 nanoseconds minimum to the START CONVERT input (pin 31) at a rate of 500 KHz. This rate chosen to reduce flicker if LED's are used on the outputs for calibration purposes. 4. To confirm proper operation of the device, vary the precision reference voltage source to obtain the output coding listed in Table 4. 2. Zero Adjustments - Apply a precision voltage reference source between the analog input (pin 3) and ground (pin 16). Adjust the output of the reference source per Table 3. For unipolar, adjust the zero trimming potentiometer so that the output code TABLE 4. OUTPUT CODING STRAIGHT UNIPOLAR INPUT RANGES, V de SCALE +FS -1 LSB 7/8 FS 314 FS 112 FS 1/4 FS 118 FS 1 LSB 0 oto +10V oto +20V +9.9976V +8.7500V +7.5000V +5.0000V 2.5000V 1.2500V 0.0024V O.OOOOV BIN COMP BINARY OUTPUT CODING MSB LSB +19.9951V 1111 1111 1111 +17.500V 1110 0000 0000 +15.000V 1100 0000 0000 +10.000V 1000 0000 0000 +5.0000V 0100 0000 0000 +2.5000V 0010 0000 0000 +0.0049V 000000000001 O.OOOOV 0000 0000 0000 OFF BINARY INPUT RANGE BIPOLAR LSB MSB 0000 0000 0000 0001 1111 1111 00111111 1111 0111 1111 1111 1011 1111 1111 1101 1111 1111 111111111110 111111111111 CO~1P OFF ±10Vde +9.9951V +7.5000V +5.0000V O.OOOOV -5.0000V -7.5000V -9.9951V -10.000V SCALE +FS-1 LSB +3/4 FS +1/2 FS 0 -1/2 FS -3/4 FS -FS +1 LSB -FS BIN +15V de Oto +10V ADC-508 SlHCONTROL ORDERING INFORMATION MODEL NO. OPERATING TEMP. RANGE SEAL AOC-508BMC ADC-508BMM 0 to +70 °C -55 to +125 °C Hermetic Hermetic ·15V .15V OFFSET ADJUST Figure 3. ADC-SHM Connection Diagram Receptable for PC board mounting can be ordered through AMP Incorporated, #3-331272-8 (Component Lead Socket), 32 required. 2-24 DATEL, Inc. 11 Cabot BOUlevard, Mansfield, MA 02048-1194ITEL (508) 339-3000ITLX 174388/FAX (508) 339-6356 ADC-511 12-Bit, High-Speed, Low-Power AID Converter PlMIlil pm m mmp FEATURES • 12-Bit resolution • 1.0 Microsecond maximum conversion time • Low-power, 925 milliwatts • Three-state, output buffers • Functionally complete • Small 24-pin DIP • No missing codes GENERAL DESCRIPTION INPUT/OUTPUT CONNECTIONS PIN FUNCTION DATEL's ADC-511 uses an advanced design to provide a highspeed, functionally complete 12-bit AID converter in a small 24-pin DIP. The ADC-511 delivers a conversion speed of 1 microsecond while consuming only 925 milliwatts of power. 1 2 3 4 5 6 7 8 9 10 11 12 Manufactured using thin- and thick-film hybrid technology, the ADC-511 's exclusive performance is based upon a digitallycorrected subranging architecture. DATEL further enhances this technology by using a proprietary custom chip and unique laser trimming schemes. Functionally complete, the ADC-511 contains an internal clock, three-state outputs and an internal reference. BIT 12 OUT (LSB) BIT 11 OUT BIT 100UT BIT 9 OUT BIT 8 OUT BIT 7 OUT BIT 6 OUT BIT 5 OUT BIT40UT BIT30UT BIT20UT BIT 1 OUT (MSB) PIN FUNCTION 13 14 15 16 17 18 19 20 21 22 23 24 +5V DIGITAL GROUND EOC START CONVERT ENABLE (1 -12) COMPBIN ANALOG INPUT BIPOLAR +10VREF +15V ANALOG GROUND -15V +10VRE 2 1 i 1 - - - o - - - - - - - 1 - j f - - - - - l OIGITAL CORRECTION LOGIC COMP. BIIiI START CONY. EOC 22 +5V OIG.GNO. For Immediate Assistance, Dial 1-800-233-2765 +15V ANAGNO. ·15V 2-25 ADC-511 ABSOLUTE MAXIMUM RATINGS PARAMETERS LIMITS UNITS PERFORMANCE +15V Supply (Pin 22) -15V Supply (Pin 24) +5V Supply(Pin 13) o to +18 Oto -18 -0.5 to +7 Voltsdc Volts dc Volts dc -0.3 to +7 Volts dc -25 to +25 300 Voltsdc ° C max. Bipolar Zero Error ill Bipolar Zero Tempco Bipolar onset Error ill Bipolar Offsat Tempco Gain Error ill Gain Error Tempco Conversion Time +25°C 0- °C to +70 °C -55°C to +125 °C No missing codes (For 12 binary bits) Digital inputs (Pins 16, 17, and 18) Analog input Lead temp. (10 sec.) FUNCTIONAL SPECIFICATIONS Apply over the operating temperature range and at ±15V dc and ±5V dc unless otherwise specified. INPUTS Analog Signal Range (See Table 5 also) Input Impedance Resistance Capacitance Logic Levels: Logic 1 Logic 0 Logic Loading: Logic 1 Logic 0 MIN. TYP. - Oto +10 ±5 2 2.5 - - MAX.; UNITS - Volts Volts - KOhms pF 50 - 0.8 - Volts Volts - - - 2.5 -100 ~ ~ 12 - - Bits 2.4 - 0.4 Volts Volts rnA 2.0 - MIN. TYP. MAX. UNITS - ±1 ±2 ±2 ±17.5 ±2 ±17.5 ±3 ±5 ±4 ±35 ±4 ±35 LSB ppmfOC LSB ppml°C LSB ppm/oC - - - - 1.0 IlSec. 1.0 - ~ec. 1.15 IlSec. Guaranteed over operating temp. range POWER REQUIREMENTS Power Supply Range +15V dc Supply -15V dc Supply +5V dc Supply Supply Current +15V Supply -15V Supply +5V Supply ® Power Dissipation Supply Rejection 14.25 14.25 +4.75 +15 -15 +5 +15.75 -15.75 +5.25 Voltsdc Volts dc Volts dc - +20 -20 +65 925 +29 -28 +79 1250 -±0.01 rnA rnA rnA mW %FSR/%V - - +70 +125 °C °C - +150 °C - PHYSICAUENVIRONMENTAL Operating Temperature Range -MCModels 0 -MMModels -55 Storage Temperature Range -65 Package Type Weight 24-pin hermetically sealed ceramic DIP 0.42(12)oz.(gram) OUTPUTS Resolution Logic Levels: Logic 1 Logic 0 Logic Loading: Logic 1 Logic 0 Internal Reference: +Voltage, +25° C Tempco External current - - - - - -160 6.4 9.98 10 ±5 10.02 ±30 1.5 - - Output Coding: - I]) Specifications cited are at +25 ae. See Techical Note 1 for further information. ® + 5V power usage at 1 TIL logic loading per data output bit. ~ Voltsdc ppm/oC rnA Straight binary/Offsat binary Complementary binary Complementary onset binary PERFORMANCE Integral Nonlinearity +25°C o °C to +70 °C -55°C to +125 °C Differential Nonlinearity +25°C o °C to +70 °C -55°C to + 125 °C Full·Scale Absolute Accuracy +25°C o °C to +70 °C -55°C to +125 °C Unipolar Zero Error ill Unipolar ZeIO Tempco 2-26 - ±1/2 ±1/2 ±3/4 ±3/4 - - ±1.5 - ±1/2 ±1/2 ±3/4 ±3/4 - - - ±3 ±4 ±8 ±1 ±13 - LSB LSB LSB ±1 LSB LSB LSB ±7 ±13 ±28 ±3 ±25 LSB LSB LSB LSB ppm/oC DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194rrEL (508) 339-3000rrLX 174388/FAX (508) 339-6356 ADC·511 TECHNICAL NOTES CALIBRATION 1. Applications unaffected by endpoint errors or those that remove them through software will use the typical connections shown in Figure 2. The optional external circuitry of Figure 4 removes system errors or helps adjust the small initial errors of the ADC-511 to zero. The external adjustment circuit has no affect on the throughput rate. Table 1 shows how to select the input range. 1. The data outputs should be connected to LED's to observe the resulting data values. Connect the converter per Figure 2, Figure 4, and Table 1 for the appropriate Full Scale Range (FSR). Apply a pulse of 200 nanoseconds minimum to the START CONVERT input (pin 16) at a rate of 250 KHz. This rate is chosen to reduce flicker if LED's are used on the outputs for calibration purposes. 2. Rated performance requires using good high frequency circuit board layout techniques. The analog and digital grounds are connected internally. Avoid ground-related problems by connecting the digital and analog grounds to one point, the ground plane beneath the converter. This prevents contamination of the analog ground by noisy digital ground currents. 2. Zero Adjustments Apply a precision voltage reference source between the amplifier's signal input and analog ground. Use a very lownoise signal source for accurate calibration. Adjust the output of the reference source per Table 4. For unipolar operation, adjust the zero trimming potentiometer so that the output code flickers equally between 0000 0000 0000 and 0000 0000 0001 with the COMP BIN (pin 18) tied high or between 1111 1111 1111 and 1111 1111 1110 with pin 18 tied low. 3. Bypass the analog and digital supplies and the + 10V reference (pin 21) to ground with a 4.7."F, 25V tantalum electrolytic capacitor in parallel with a 0.1 ."F ceramic capacitor. Bypass the + 1OV reference (pin 21) to analog ground (pin 23). For bipolar operation, adjust the potentiometer such that the code flickers equally between 1000 0000 0000 and 1000 0000 0001 with pin 18 tied high or between 0111 1111 1111 and 0111 1111 1110 with pin 18 tied low. 4. Obtain straight binary/offset binary output coding by tying COMP BIN (pin 18) to +5V dc or leaving it open. The device has an internal pull-up resistor on this pin. To obtain complementary binary or complementary offset binary output coding, tie pin 18 to ground. The complementary signal is compatible to CMOSITTL logic levels for those users desiring logic control of this function. 3. Full-Scale Adjustment Set the output of the voltage reference used in step 2 to the value shown in Table 4. Adjust the gain trimming potentiometer so that the output code flickers equally between 1111 1111.1110 and 1111 1111 1111 for pin 18 tied high or between 0000 0000 0001 and 0000 0000 0000 for pin 18 tied low. 5. To obtain Three-State outputs, connect ENABLE (pin 17) to a logic "0" (low). Otherwise, connect pin 17 to a logiC "1" (high). To confirm proper operation of the device, vary the precision reference voltage source to obtain the output coding listed in Table 6. TIMING Figure 3 shows the relationship between the various input signals. The timing shown applies over the operating temperature range and over the operating power supply range. These times are guaranteed by design. Table 1. Input Connections INPUT RANGE oto -10V dc ±5Vdc OPTIONAL CALIBRATION CIRCUIT (SEE AGUAE 4) INPUT PIN Pin 19 Pin 19 JUMPER THESE PINS: Pin 20 to GROUND Pin 20 to Pin 21 Table 4. Zero and Gain Adjust ~ s~~~ "----'...---1-"1-1_-,Ir-<>--(i:I FSR BITI (MSS) Bin BIT' BIf4 "'H01TlCDrrlC"'OM"'Mm""""U ......"'I.._......J ADC-511 I-~I 141 BIPOLAR OPERATION Figure 2. Typical Input Connections for the ADC-511 For Immediate Assistance, Dial 1-800-233-2765 BITS Bin o to +10V de ±5Vdc ZERO ADJUST +1/2 LSB GAIN ADJUST +FS· 1 1/2 LSB +1.22mVdc +1.22mVdc +9.9963Vdc +4.9963Vdc BIT7 BITS BITO BI110 BIT'1 SrT12 (LSB) EtlC' EfiWR:E"(1-12) Table 5. Input Ranges (using external calibration) INPUT RANGE R1 R2 UNIT o to +10V, +5V o to +5V, ±2.5V o to +2.5V, +1.25V 2 2 2 2 6 14 KOhms KOhms KOhms 2-27 Table 6. Output Coding STRAIGHT BIN UNIPOLAR INPUT RANGES, V de SCALE +FS -1 LSB 7/8 FS 3/4 FS 112 FS 1/4 FS 118 FS 1 LSB 0 LSB MSB 111111111111 111 0 0000 0000 1100 0000 0000 1000 0000 0000 010000000000 0010 0000 0000 000000000001 0000 0000 0000 Oto +10V +9.9976V +8.7500V +7.5000V +5.0000V +2.5000V +1.2500V +0.0024V O.OOOOV COMP BINARY OUTPUT CODING OFF BINARY INPUT RANGE BIPOLAR MSB LSB 0000 0000 0000 0001 1111 1111 0011 1111 1111 0111 1111 1111 1011 1111 1111 110111111111 111111111110 111111111111 COMP OFF ±10V de +4.9976V +3.7500V +2.5000V O.OOOOV -2.5000V -3.7500V -4.9976V -5.0000V SCALE +FS -1 LSB +3/4 FS +1/2 FS 0 -1/2 FS -3/4 FS -FS +1 LSB -FS BIN Optional Calibration Circuit R2* ANALOG INPUT [ - - _ - - ;_ _ _ _ _ _ _ _ __ ! 600 I L NVERT EOC I ~..:;200"'-".c:.sec=min~ STARTeD I -l I-- ~';:UT IX! ENABLE ~ +15V nSec--l min To Pin 19 _ _ _ __ Conversion Time, max - J --, F 20 nSecmin35 20 nSec max nSec max I-- 1300 nSec min I ----l IXIXIXI Data N-1 Valid 1-+-10n$ecmax ~ ~ Data N Valid --~DataNValid 10nSecmax of ADC-511 DATA INVALID I ~ NOTE: NOT DRAWN TO SCALE GAIN ADJUST Figure 3. ADC-511 Timing Diagram 5KU ZERO/OFFSET ADJUST • See Table 5 for R1 and R2 values. Figure 4. Optional Calibration Circuit MECHANICAL DIMENSIONS INCHES (MM) 1 I 0.800 MAXI (20,3) 0.190 MAX ORDERING INFORMATION I ---,........:.:c..n{47<,9) ~ I ~ 0.010 x 0.018 0.150 MIN. (3,8) KOVAR Pins I 112 131-r 11 1.310 MAX. 1BOTTOM 1 SPACES (33,3) 1 VIEW 1 AtO~100 (2,5) 11 I 241~ 0.600 (15,2) I MODEL TEMPERATURE RANGE ADC-511 MC 0 °C to +70 °C ADC-511MM -55°C to +125 °C ADC-511/883B -55°C to +125 °C SEAL Hermetic Hermetic Hermetic A receptacle for PC board mounting can be ordered through AMP Incorporated, #3-331272-8 (Component Lead Socket), 24 required. NOTE; Pins have 0.025 Inch ±0.01 standoff from case. t-IJTE; Pins have a 0.025 Inch, ±a.01 standoff from case. 2-28 DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 0204S-1194ITEL (50S) 339-3000ITLX 17438S/FAX (50S) 339-6356 ADC-520, ADC-521 12-Bit, Ultra-Fast, Low-Power AID Converters FEATURES • • • • 12-Bit resolution 800 Nanosecond maximum conversion time Pin-programmable input ranges Internal high impedance buffer Low 1.6 watts power consumption Three-state output buffers Small 32-pin DIP No missing codes GENERAL DESCRIPTION MECHANICAL DIMENSIONS INCHES (mm) DATEL's ADC-520 and ADC-521 are 12-bit analog-to-digital converters with conversion speeds of up to 800 nanoseconds. Both models are identical except for the analog input voltage ranges. I 1.101 MAX I --(2B.0)-~ 0.190 MAX ~ =-=-.l ~0.010 X O.D1B The performance of these converters is based upon a digitally-correcting subranging architecture. DATEL further enhances this technology by using unique laser trimming schemes. The ADC-520 and ADC-521 are packaged in a 32-pin ceramic DIP and consume 1.6 watts. KOVAR Pins 17 BOTTOM VIEW TECHNICAL NOTES 0.150 MIN. (3,B) T) 15 SPACES 1.712 MAX. (43,S) AT 0.100 (2,5) 1. Use external potentiometers to remove system errors or the small initial errors to zero. Use a 20K ohm trimming potentiometer for gain adjjustment with the wirper tied to pin 27 (ground pin 27 for operation without adjustments). Use a 20K ohm trimming potentiometer with the wiper tied to pin 19 for zer%ffset adjustment (leave pin 19 open for operation without adjustment). '-------' -hL 0900 NOTE: Pins have a 0.025 inch, ±0.01 stand-off from case. (22,9) 1/0 CONNECTIONS BUFl'EA INPUT PIN BUFFER FUNCTION PIN FUNCTION BIT 12 OUT (LSB) BIT 11 OUT BIT 10 OUT BIT90UT BIT80UT BIT 7 OUT BIT 6 OUT BIT 5 OUT BIT 4 OUT BIT30UT BIT 2 OUT BIT lOUT (MSB) BIT lOUT (MSB) ENABLE DIGITAL GROUND +5V 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 COMPBIN REF. OUT (+ 10V de) OFFSET ADJUST EOC START CONVERT RANGE 1 RANGE 2 INPUT HIGH BIPOLAR OFFSET INPUT LOW GAIN ADJUST +15V BUFFER OUTPUT BUFFER INPUT ·15V ANALOG GROUND OUTPUT ~~~ST €J-~-++-+------, ,--1----illl BIT lOUT (MS'li) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 For Immediate Assistance, Dial 1-800-233-2765 2-29 ADC·S20, ADC·521 2. Rated performance requires using good high frequency circuit board layout techniques. The analog and digital grounds are not connected internally. Avoid ground-related problems by connecting the digital and analog grounds to one pOint, the ground plane beneath the converter. Due to the inductance and resistance of the power supply return paths, return the analog and digital ground separately to the power supplies. 3. Bypass all the analog and digital supplies and the + 1OV reference (pin 18) to ground with a 4.7 I-lF, 25V tantalum electrolytic capacitor in parallel with a O.II-lF ceramic capacitor. Bypass the + 1OV reference (pin 18) to analog ground (pin 32) the same way. 4. QQ.tain straight binary/offset binary output coding by tying CaMP BIN (pin 7) to +5V de or leaving it open. The device has an internal pull-up resistor on this pin. To obtain complementarv binary or complementary offset binary output coding, tie the CaMP BIN pin to ground. In the bipolar mode, two's complement QUlputcoding.is available by using the MSB output (pin 13). The CaMP BIN signal is compatible to CMOSmL logic levels for those users desiring logic control of this function. 5. Enable the three-state outputs by connecting ENABL~n 14) to a logic 0 (low). The ENABLE signal has no effect on MSB (pin 13) which is not a three-state output and therefore is not controlled by the enable pin. 6. Satisfy high-speed drive requirements of the ADC-520, -521 with a wide-bandwidth, low output impedance input source such as DATEL's SHM-45 sample-and-hold or AM-1435 amplifier. 7. The ADC-520,-521 provide an internal buffer amplifier. Using this buffer provides an inut impedance of 1012 ohms, allowing the AID to be driven from a high impedance source or directly from an analog multiplexer. When using the input buffer, allow a delay equal to its settling time between input level change and the negative going edge of the START CONVERT pulse. If the buffer is not required, its input should be connected to analog ground to avoid introducing noise into the converter. (ADC-521) 2-30 - UNITS 1.75 3.75 2.5 5.0 - - KOhms KOhms 2.0 1.6 2.5 2.0 - - KOhms KOhms - - 50 pi - Voltsdc Ohms nSec. +10 - - 1012 700 - 1000 DIGITAL INPUTS Logic Logic Logic Logic "I" "0" Loading "1" Loading "0" 2.0 - - - - - - 0.8 5 -200 12 2.4 - Volts dc Voltsdc J.lA J.lA OUTPUTS Resolution Logic "1" Logic "0" Logic Loading "1 " Logic Loading "0" Internal Reference Voltage, +25 "C Drift External Current - - - - 9.98 - 10.0 ±5 - - Output Coding (Pin 17HI) (Pin 17 Low) - 0.4 -160 6.4 10.02 ±30 1.5 Bits Voltsdc Voltsdc J.lA rnA Volts dc ppm! "C rnA Straight binary/offset binary Complementary binary Complementary offset binary Two's complement Complementary two's complement Volts dc Voltsdc Volts dc Integral Non-linearity +25"C o "Cto +70 "C - - ±1/2 ±1/2 LSB LSB -0.3 to +6.0 -15to +15 300 Volts dc Volts dc Integral Non-Lin. Tempco - ±3 ±8 ppm!°C Differential Non-Linearity +25"C o OCto +70"C - - ±1/2 ±1/2 LSB LSB Differential Non-Lin. Tempco - - ±2.5 ppm!"C UNITS Full Scale Absolute Accuracy +25"C O"C to +70"C - ±3 ±4 ±8 ±14 LSB LSB Unipolar Operation Zero Error (j) Zero Tempco Zero Adjust Range - ±1 ±13 ±5 ±25 LSB ppm/"C LSB MIN. - MAX. Oto+18 Oto-18 -0.5 to +7.0 PERFORMANCE "C The following specifications apply over the operating temperature range and at ±15V dc and +5V dc unless otherwise specified. - Buffer Amplifier Input Voltage Input Impedance Settling Time TYP. UNITS FUNCTIONAL SPECIFICATIONS Input Range (ADC-520) Input Capacitance MIN. LIMITS PARAMETERS ANALOG INPUTS (ADC-520) Unipolar: Bipolar: (ADC-521) Unipolar: Bipolar: (Note 4) (Note 4) ABSOLUTE MAXIMUM RATINGS +15V Supply (Pin 28) -15V Supply (Pin 31) +5V Supply (Pin 16) Digital Inputs (Pins 14, 17, 21) Analog Input (Pin 24) Lead Temp.(10 Sec.) Input Impedance TYP. MAX. ±10 Oto-20 - Volts Volts Volts Volts ±2.5 Oto+5 - Volts de Volts dc oto +10 oto +20 de de de de ±5 - - DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194ITEL (508) 339-3000ITLX 174388/FAX (508) 339-6356 ADC-S20, ADC-521 & Bipolar Operation Table 2b. MIN. TYP. MAX. UNITS - ±1 ±2 ±5 ±5 - ±2 ±17.5 ±5 ±35 ±5 - - LSB ppm/°C LSB LSB ppm/°C LSB - ±2 ±17.5 ±5 ±35 LSB ppm/°C ±5 - - LSB - - 800 850 nSec. nSec. Zero Error(j) Zero Tempco Zero Adjust Range Offset Error (j) Offset Tempco Offset Adjust Range - ±5 - Gain Error (j) Gain Tempco Gain Error Adjust Range Conversion Times +25°C o OCto +70 °C - INPUT PIN ±2.5V de Oto +5Vde Power Supply Current +15V dc Supply -15V dc Supply +5V de Supply' Power Dissipation Power Supply Rejection BUFFER WITH BUFFER Pin 24,22,23 Pin 24,22,23 Pin 30, tie 29 to 24 Pin 30, tie 29 to 24 : Pin 25 to 18 Pin 25 to 26 I l----250 n S I TIME ~ I .------------------------ ...fl.... I N~ I 1r-_SO_",;.i'_'M_'N_'M_U_"_________________________ i I STA~T! : I Over the Operating Temperature Range e~ I , CONVERT NOTE NOT DRAWN TO SCALE --------';------------------------------- l S~~~I~~G "1 -72 dB min. -72 dB min. -65 dB min. CONNECT ANALOG INPUT~ : ...j I : : I I_I ! mG POWER REQUIREMENTS Power Supply Range +15V dc Supply -15V de Supply +5V de Supply W/O INPUT RANGE ANALOG Harm. Distort. (-FS) ® +25°C o to +70 °C -55 to +125 °C No Missing Codes (12 Bits) ADC-521 Input Connections ! !- CONVERSK>N TIME MAX F -------j L 30 nSec MAXIMUM --I --I l--25 nSec. MINIMUM +14.25 -14.25 +4.75 +15.0 -15.0 +5.0 +15.75 -15.75 +5.25 Voltsdc Volts de Voltsdc - +52 -36 +66 1.6 - - +65 -45 +70 1.9 0.01 mA mA mA Watts %FSR/%V 0 - +70 °C -65 - +150 °C r---350nSec MINIMUM OUTPUT DATA DATAN·>VAl'D ENABlED DATA N·' VALID ~ lOnSe<: MAXIMUM DATANVALID F ENABLED DATA N VALID Figure 2. ADC-520, ADC-521 Timing Diagram PHYSICAL/ENVIRONMENTAL Operating Temp. Range Storage Temperature Range Package Type Pins Weight TIMING 32-Pin hermetic sealed, ceramic DIP 0.010 x 0.018 inch Kovar 0.42 ounces (12 grams) • +5V power usage at 1 TTL logic loading per data output bit. (j) Specifications cited are at +25 °C. See Technical Note 1 for further information. ® With DATEL SHM-45, see Figure 3. INPUT CONNECTIONS Table 2a. INPUT RANGE ±10V de o to +10V de Oto +20Vde Oto -20Vde ADC-520 Input Connections INPUT PIN WITH BUFFER BUFFER W/O Pin 24 Pin 24 Pin 24 Pin 25 Pin 30, tie 29 to 24 Pin 30, tie 29 to 24 DO NOT USE DO NOT USE For Immediate Assistance, Dial 1-800-233-2765 CONNECT Pin 18 to 25 Pin 24 to 25 Pin 26 to 25 Pin 18 to 24, 22 to 23 to 24 Figure 2 shows the relationship between the various input signals. The timing cited applies over the operating temperature range and over the operating power supply range. These times are guaranteed by design. CALIBRATION PROCEDURE 1. Connect the converter per Figure 3 and Tables 2a and 2b for the appropriate full-scale range (FSR). Apply a pulse of 50 nanoseconds minimum to the START CONVERT input (pin 21) at a rate of 500 KHz. This rate reduces flicker if LED's are used on the outputs for calibration purposes. 2. Zero Adjustments - Apply a precision voltage reference source between the analog input and ground. Refer to Tables 2a and 2b for the correct input pin. Adjust the output of the reference source per Table 3. For unipolar, adjust the zero trimming potentiometer so that the output code flickers equally between 0000 0000 0000 and 0000 0000 0001 with the COMP BIN (pin 17) tied high (straight binary) or between 1111 1111 1111 and 1111 1111 1110 with the COMP BIN tied low (complementary binary). For bipolar operation, adjust the potentiometer such that the code flickers eQually between 1000 0000 0000 and 1000 0000 0001 with COMP BIN (pin 17) tied high (offset binary) or between 0111 1111 1111 and 0111 1111 1110 with COMP BIN (pin 17) tied low (complementary offset binary). 2-31 ADC·S20,ADC·S21 Two's complement and complementary two's complement requiresthe use of MSB (pin 13) versus MSB (pin 12) as given for offset binary or complementary offset binary respectively. 3. Full-Scale Adjustment - Set the output of the voltage reference used in step 2 to the value shown in Table 3. Adjust the gain trimming potentiometer 50 that the output code flickers eoually between 111111111110and 111111111111 forCOMPBIN (pin 17) tied high or between 0000 0000 0001 and 0000 0000 0000 for COMP BIN tied low. Two's complement and ~Ie mentary two's complement respectively requires using MSB, pin 13. 4. To confirm proper operation of the device, vary the precision reference voltage source to obtain the output coding listed in Tables 4 and 5. Table 3. Zero and Gain Adjust FSR ZERO ADJUST +1/2 LSB GAIN ADJUST +FS -11/2 LSB Oto +5V +0.610mVdc +1.22 mVdc +2.44 mVdc -2.44 mVdc +2.44 mV dc +0.610 mVdc +4.9971Vdc +9.9963Vdc +19.9927V dc -19.9927V dc +9.9927V dc +2.4982Vdc oto +10V dc Oto +20V dc Oto -20Vdc +10Vdc +2.5Vdc OFFSET ADJUST Figure 3. ADC/SHM Connection Diagram Table 4. Output Coding for Unipolar Operation UNIPOLAR SCALE INPUT RANGES VOLTS de o 10 010 .5V +FS·1LSB 7/8 Fs 3I4FS 112FS 1/4FS 1/8FS 1 LSB 0 +4.9988V +4.3750V +3.7500V +2.5000V +1.2500V +0.0024V +0.0012V O.OOOOV OUTPUT CODING STRAIGHT BINARYCOMP. BINARY .10V 0 10 .20V MSB LSB LsB MSB +9.9976V +8.7500V +7.5000V +5.0000V +2.5000V +1.2500V +0.0024V O.OOOOV +19.9951V +17.500V +15.000V +10.000V +5.0000V +2.5000V +0.0048V O.OOOOV 111111111111 1110 0000 0000 1100 0000 0000 1000 0000 0000 0100 0000 0000 0010 0000 0000 0000 0000 0001 0000 0000 0000 0000 0000 0000 000111111111 0011 1111 1111 0111 1111 1111 1011 1111 1111 110111111111 111111111110 1111 1111 1111 Table 5. Output Coding for Bipolar Operation BIPOLAR SCALE +FS·l LSB +3/4 Fs +1I2FS 0 -1I2FS -314 FS -FS +1 LSB -FS INPUT RANGES,VOLTS de .t 2 .5V .t 1OV +2.4988V +1.8750V +1.2500V O.OOOOV -1.2500V -1.8750V -2.4988V -2.5000V +9.9951V +7.5000V +5.0000V . O.OOOOV -5.0000V -7.5000V -9.9951 V -10.000V OFFSET BINARY MSB LsB 111111111111 11100000 0000 1100 0000 0000 1000 0000 0000 0100 0000 0000 0010 0000 0000 0000 0000 0001 0000 0000 0000 OUTPUT CODING COMP TWO'S COMP TWO'S COMPo LSB MSB LsB MSB 1000 0000 0000 1001 1111 1111 101111111111 111111111111 0011 1111 1111 0101 1111 1111 0111 1111 1110 0111 1111 1111 0111 11111111 0110 0000 0000 0100 0000 0000 0000 0000 0000 1100 0000 0000 101000000000 1000 0000 0001 1000 0000 0000 ORDERING INFORMATION MODEL NO. OPERATING TEMP. RANGE ADC-520MC ADC-521MC Oto +70 °C oto +70 °C Order PC board mounting receptacle through AMP Inc. part #3-331272-8 (Component Lead Socket), 32 required. 2-32 DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194ITEL (508) 339-3000ITLX 174388JFAX (508) 339-6356 ADC-530 12-Bit, Ultra-fast, Low-Power AID Converter FEATURES • • • • • • • • 12-Bit resolution 350 Nanoseconds maximum conversion time Low-power,2.1W Small initial errors Three-state output buffers -55 to +125 °C operation Small 32-pin DIP No missing codes INPUT/OUTPUT CONNECTIONS GENERAL DESCRIPTION PIN DATEL's ADC-530 reflects the ultimate in state-of-the-art analog signal conversion technology. The ADC-530 boasts a conversion speed of 350 nanoseconds, along with a low-power consumption of 2.1 watts. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 DATEL's ADC-530 is a 12-bit analog-to-digital converter which has small initial errors and can also provide adjustment capability for system errors. The ADC-530 has a maximum conversion time of 350 nanoseconds. Manufactured using thick-film and thin-film hybrid technology, this converter's remarkable performance is based upon a digitally-corrected subranging architecture. DATEL further enhances this technology by using a proprietary custom chip and unique laser trimming schemes. The ADC-530 is packaged in a 32-pin ceramic DIP. SIGNAL NAME +10VREF.OUT RANGE INPUT HIGH INPUT LOW OFFSET ADJUST DO NOT CONNECT COMPBIN OVERFLOW ENABLE (BITS 7-12) ENABLE (BITS 1-6) & OVERFLOW +5V DIGITAL GROUND +15V -15V NO CONNECTION ANALOG GROUND PIN SIGNA NAME 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 SIR CONTROL EOC BIT 12 OUT (LSB) BIT11 OUT BIT100UT BIT 9 OUT BIT 8 OUT BIT 7 OUT BIT60UT BIT50UT BIT40UT BIT30UT BIT20UT BIT lOUT (MSB) START CONVERT GAIN ADJUST GAIN ADJUST +10VAEF 321--==---++-------, 10 ENABLE BITS 1-5 & OVERFLOW 11---::.=---++-----1 30 BIT 1 (MSB) 29 BIT 2 OFFSET ADJUST 5 RANGE 2 INPUT HI INPUT LOW 28 BIT 3 27 BIT 4 26 BIT 5 25 BIT 6 24 BIT 7 3 I"""",~+-"""'-f 4 23 BIT 8 22 BIT 9 21 BIT10 COMPBIN 7 ~~~=i 31 EOC 18 SJH CONTROL 17 2081T11 19 BIT 12 (LSB) LOGIC CONTROLI----------=_i AND TIMING ~=============~...!J 15 NO CONNECTION For Immediate Assistance, Dial 1-800-233-2765 DO NOT CONNECT 9 ENABLE BITS 6-12 8 OVERFLOW 11 12 13 16 14 +5V OIG.GNO. +15V ANA. GND. -15V 2-33 ADC-530 All digital inputs and three-state outputs are TTL- and CMOScompatible. Output coding can be in straight binary/offset binary or complementary binary/complementary offset binary by using the COMP BIN pin. An overflow pin indicates when inputs are below or above the normal full-scale range. A novel feature of the ADC-530 is the provision of a Sample/ ROld control pin for applications where a sample-hold is used in conjunction with the ADC-530. This feature allows the sample-and-hold device to go back into the sample mode a minimum of 30 nanoseconds before the conversion is complete, improving the overall conversion rate of the system. ABSOLUTE MAXIMUM RATINGS o to +18V dc oto -18V dc +15V Supply (Pin 13) -15V Supply (Pin 14) +5Y Supply (Pin 11) -0.5 to +7V dc Digital Inputs (Pins 7,9,10, & 31) Analog Input (Pin 3) Lead temperature (10 Sec.) -0.3 to +6V dc -15 to +15V dc 300 DC max. PERFORMANCE Full-Scale Abs. Accuracy +25 aC Oto +70 ac -55 to +125 ac Unipolar Zero Error +25 aC Unipolar Zero Tempco Bipolar Zero Error +25 aC Bipolar Zero Tempco Bipolar Offset Error +25 ac Bipolar Offset Error Tempco Gain Error, +25 ac Gain Tempco Conversion Times +25 ac oto +70 ac -55 10+ 125 ac No Missing Codes (12 Bits) MIN. TYP. MAX. UNITS - ±0.1 ±D.13 ±D.2 ±D.25 ±D.32 ±0.5 %FSR %FSR %FSR - ±D.05 ±13 ±D.13 ±25 %FSR ppm/ ac - - ±D.05 ±13 ±D.13 ±25 %FSR ppm/ac - ±D.l ±D.2 %FSR ±35 ±D.17 ±35 ppm/ac %FSR ppm/ac - - ±17.5 ±0.08 ±17.5 +14.25 -14.25 +4.75 +15 -15 +5 +15.75 -15.75 +5.25 Vdc Vdc Vdc - +60 -30 +150 2.1 +70 -40 +180 2.5 0.01 rnA rnA rnA - nSec. 350 400 nSec. 400 nSec. Over the operating temp. range - . POWER SUPPLY REQUIREMENTS FUNCTIONAL SPECIFICATIONS Apply over the operating temperature range and at ±15V dc and +5V power supply voltages unless otherwise specified. Power Supply Range +15V dc Supply -15V dc Supply +5V dc Supply Power Supply Current +15V Supply -15VSupply +5V Supply' Power Dissipation Power Supply Rejection - - Watts %FSRJ%V PHYSICAUENVIRONMENTAL INPUTS Input Voltage Range (See Tech Note 9) Logic Levels Logic 1 Logic 0 Logie Loading Logic 1 Logic 0 MIN. - TYP. Oto+l0 oto +20 ±10 MAX. - - - 0.8 Vdc Vdc - - - 2.5 -100 ItA ItA 2.4 - - 0.4 Vdc Vdc - - -160 6.4 I1A rnA 9.98 10.0 ±5 10.02 ±30 1.5 Vdc ppm/aC 2.0 - UNIT Vdc Vdc Vdc OUTPUTS Logie Levels Logic 1 Logic 0 Logic Loading Logic 1 Logic 0 Internal Reference Voltage, +25 DC Drift External Current Output Coding (Pin 7 High) (Pin 7 Low) 2-34 Oto+70 aC -55 to+125 ac -65 to +150 ac 32-pin hermetic, ceramic DIP 0.42 ounces (12 grams) •+5V power usage at 1 TTL logic loading per data output bit TECHNICAL NOTES - - - - rnA straight binary/offset binary complementary binary complementary offset binary PERFORMANCE Integral Nonlinearity +25 aC Oto+70 aC -55 to+ 125 ac Differential Nonlinearity +25 ac oto +70 ac -55 to +125 ac Operating Temperature Range, Case -MC -MM Storage Temp. Range Package Type Weight - - ±3/4 ±314 ±1.5 LSB LSB LSB - ±3/4 ±3/4 ±1.5 LSB LSB LSB - ±1/2 1. Use external potentiometers to remove system errors or the small initial errors to zero. Use a 20K trimming potentiometer for gain adjustment with the wiper tied to pin 32 (ground pin 32 for operation without adjustments). Use a 20K trimming potentiometer with the wiper tied to pin 5 for zero/ offset adjustment (leave pin 5 open for operation without adjustment). 2. Rated performance requires using good high frequency circuit board layout techniques. The analog and digital grounds are not connected internally. Avoid ground-related problems by· connecting the digital and analog grounds to one point, the ground plane beneath the converter. Due to the inductance and resistance of the power supply return paths, retun tAe analog and digital ground separately to the power supplies. 3. Bypass all the analog and digital supplies and the +10V reference (pin 1) to ground with a 4.7 l1F, 25V tantalum electrolytic capacitor'in parallel with a 0.1 l1F ceramic capacitor. Bypass the + 1OV reference· (pin 1) to analog ground (pin 16). DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-11941TEL (508) 339-30001TLX 174388/FAX (508) 339-6356 ADC-530 4. Obtain straight binary/offset binary output coding by tieing CoMpSTIii (pin 7) to +5V dc or leaving it open. The device has an internal pull-up resistor on this pin. To obtain complementary bin~.()i~omplementary offset bin~ry_().u!!>!Jt coding tie the COMP BIN pin to ground. The COMP BIN signal is compatible to CMOS/TTL logic levels for those users desiring logic control of this function. CALIBRATION PROCEDURE 5. An overflow signal, pin 8, indicates when analog input signals are below or above the desired full-scale range. The overflow pin also has a three-state output and is enabled by pin 10 (ENABLE bits 1-5 & O.F.). 2. Zero Adjustments Apply a precision voltage reference source between the analog input (pin 3) and ground (pin 16). Adjust the output of the reference source per Table 3. For unipolar, adjust the zero trimming potentiometer so that the output code flickers equally between 0000 0000 0000 and 0000 0000 0001 with the COMP BIN (pin 7) tied high or between 1111 1111 1111 and 111111111110 with pin 7 tied low. 6. The sample-and-hold (S/H) control signal, pin 17, goes low following the rising edge of a start convert pulse and high 30 nanoseconds minimum before EOC goes low. This indicates that the converter can accept a new analog input. 7; The drive requirements of the ADC-530 may be satisfied with a wide-bandwidth, low output impedance input source. Applications of these converters that require the use of a sample-and-hold may be satisfied by using DATEL's model SHM-45 .. Using this device with multiplexers or for test purposes will require an input buffer. 8. Over temperature, input capacitance is 50 pF maximum and input impedance is 1.75K minimum (2.5K typical) for a to +10V and 3.75K minimum (5K typical) for a to +20V, ±10V. These values are guaranteed by design. 9. Requirements for ±2.5V inputs can be satisfied using DATEL's AM-1435 amplifier in front of the SHM-45/ADC-530 configuration, shown in Figure 3, at the appropriate gain. The SHM-45's gain of 2 mode allows a to +5V or ±5V input ranges. 1. Connect the converter per Figure 3 and Table 2 for the appropriate full-scale range (FSR). Apply a pulse of 100 nanoseconds minimum to the START CONVERT input (pin 31) at a rate of 500 KHz. This rate is chosen to reduce flicker if LED's are used on the outputs for calibration purposes. For bipolar operation, adjust the potentiometer such that the code flickers equally between 1000 0000 0000 and 1000 0000 0001 with pin 7 tied high or between 0111 1111 1111 and011111111110withpin7tiedlow. 3. Full-Scale Adjustment Set the output of the voltage reference used in step 2 to the value shown in Table 3. Adjust the gain trimming potentiometer so that the output code flickers equally between 1111 1111 1110 and 1111 1111 1111 for pin 7 tied high or between 0000 0000 0001 and 0000 0000 0000 for pin 7 tied low. 4. To confirm proper operation of the device, vary the precision reference voltage source to obtain the output coding listed in Table 4. TIMING Figure 2 shows the relationship between the various input signals. The timing cited applies over the operating temperature range and over the operating power supply range. These times are guaranteed by design. Table 2. Input Connections ANALOG INPUT , ANAJ.pG INPUT SETTliNG TIME 100 nSec Min. I ~~~HO~L~OM~O~OE~S=ETIL=='~~'=OO~"S~~~M~,"------- , START CONVERT ,__ ~ : -.! I I~ r;.rl 100nSacMln. (RANGE) TO PIN: a to +10V dc 3 3 Oto +20Vdc 3 16 ±10V dc 3 1 I -' r I I I I ~ SJH ACQ. TIME 200 nSec. I I I 1_ , ---I' '--, 1_ _ 30 oSec Min. Conversim1 Tinm Max. , - - 20 nSec Min." 35 nSec Max. DATA INPUT PIN --4---i ': li-'--'- - - - - - - - - - - - - - - - - - - - - ~~'T'~~~~~~---" ~: 10 nSec Min.•, 25 nSec MaK. OUTPUT CONNECT PIN 2 INPUT VOLTAGE RANGE -----1]- 35 nSec Max. 250nSecMin._1 ......J1XIXI""""'-____....:O::;Ac::;TAc:,N•.:...'V::..:AL:::'O'--____...IXIXIXIXI"""'' ' '*'-' ---___ Table 3. Zero and Gain Adjust DATA N VALID FSR ---:=-lL_E"_""..::·~=i~T:::..~,c:..~-1_V._lid5--,O-"-S.-,.M:c-.-'.-=+j...,.,1~ABlEDDATANVALID NOTE; NOT DRAWN TO SCALE ~ INVALID DATA ZERO ADJUST GAIN ADJUST +1/2 LSB +FS ·11/2 LSB a to +10V dc +1.22 mV +909963V dc Oto +20V dc +2.44 mV + 19.9927V .dc ±10Vdc +2.44 mV +9.9927V dc Figure 2. ADC-530 and SHM-45 Timing Diagram For Immediate Assistance, Dial 1-800-233-2765 2-35 ADC·S30 Table 4. Output Coding STRAIGHT UNIPOLAR INPUT RANGES, V de SCALE +FS -1 LSB 7/S FS 314 FS 112 FS 1/4 FS 1IS FS 1LSS 0 Oto +10V +9.9976V +S.7500V +7.5000V +5.0000V +2.5000V +1.2500V +0.0024V O.OOOOV Oto +20V +19.9951V 17.500V 15.000V +10.000V +5.0000V +2.5000V +0.0049V O.OOOOV BIN CaMP BINARY INPUT RANGE BIPOLAR OUTPUT CODING MSB LSB 111111111111 111000000000 1100 0000 0000 1000 0000 0000 0100 0000 0000 0010 0000 0000 0000 0000 0001 0000 0000 0000 OFF BINARY MSB LSB 000000000000' 0001 1111 1111 0011 1111 1111 0111 1111 1111 1011 1111 1111 1101 1111 1111 1111 1111 1110 111111111111 CaMP OFF HOV de +9.9951V +7.5000V +5.0000V O.OOOOV -5.0000V -7.5000V -9.9951V -10.000V SCALE' , +FS -1 LSB +3/4 FS +1/2 FS 0 -1/2 FS -3/4 FS -FS +1 LSB -FS BIN +15V 20K ENABLE (BITS 6,'2) GAIN ADJUST -15V ENABLE (BITS 1-5 & Figure 3. ADC-530 Calibration Setup Oto+10V INPUT +15V RANGE 13 ! - - -.....-'-jINPUTHIGH SHM-45 12 HoLD ADC-530 START CONVERT COMPBIN 17 r -_ _ _-1 =."...--:-=-':-1 10 OVERFLOW) ZERO/OFFSET ADJUST 20K SIii CONTROL +'OVREF 30 29 BIT' (MSB) BIT2 BIT 3 BIT 4 BIT 5 28 27 26 BITS 25 81T7 BIT 8 BIT9 SIT 10 81T11 BIT 12 (LSB) OVERFLOW EOC DO NOT CONNECT NO CONNECTION 24 23 22 11 2' 20 8 '8 'e 6 15 . 12 407"" MECHANICAL DIMENSIONS INCHES (MM) O.1JlF 1.101 MAX (28,0) +5V 0.190 ,MAX 4'9) ~0.010 X 0.01R· ~ KOVA:R Pins ' 17 ,16 I I I I I I I BOTTOM I I I I VIEW I I I I I I I ! 1 32 I I I I I I I I I I I I I I I I I I I ! ~ 0.150 MIN. (3,8) ORDERING INF.ORMATION 15 1.712 MAX. SPACES (43,5) AT 0.100 (2,5) ~ 0.900 (22,9) MODEL OPERATING TEMP. RANGE SEAL ADC·530MC ADC·530MM Oto+70°C -55 to +125 °C Hermetic Hermetic Receptacle for PC board mounting can be ordered through AMP Incorporated. #3-331272-S (Component Lead Socket). 32 required. For availability of MIL-STD-SS3B versions. contact DATEL. NOTE: Pins have a 0.025 inch, ±om stand-off from case. 2-36 DATEL. Inc. 11 Cabot Boulevard. Mansfield. MA 0204S-1.194ITEL (50S) 339-3000ITLX 1743SS/FAX (50S) 339-6356 ADC-908 High-Resolution Ultra-Fast AID Converter FEATURES • • • • • • • 14-Bit resolution 1.0 IlSec. conversion time Functionally complete Small 32-pin DIP Low-power, 2.9 Watts maximum Three-state output buffers No missing codes INPUT/OUTPUT CONNECTIONS PIN GENERAL DESCRIPTION DATEL's ADC-908 is a 14-bit, 1.0 microsecond conversion time, functionally complete AID converter. Packaged in a small 32-pin DIP, power requirements are ±15 volts and +5 volts with a 2.9 Watts maximum power dissipation. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 FUNCTION +10V REF. OUT BIPOLAR ANALOG INPUT SIGNAL GROUND OFFSET ADJUST GAIN ADJUST OVERFLOW COMPo BIN ENABLE +5V DIGITAL GROUND +15V -15V S/HCONTROL ANALOG GROUND BiC PIN FUNCTION 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 BIT 14 OUT (LSB) BIT 130UT BIT 12 OUT BIT 11 OUT BIT 10 OUT BIT90UT BIT 8 OUT BIT 7 OUT BIT60UT BIT 5 OUT BIT40UT BIT 3 OUT BIT20UT BIT 1 OUT (MSB) BIT 1 OUT (MSB) START CONVERT GAIN ADJUST 6 1 - - = = - - - + - + - - - - - - , +10V REF 1 1 - - - : : ; ; = - - - + - + - - - - - - 1 ,----1-..131 BIT lOUT (MSB) 30 BIT lOUT (MSB) OFFSET ADJUST 5 BIPOLAR 2 ~~;~~ 3h/~~~~-/ 24 BIT 70UT 23 BIT BOUT SIGNAL GROUND 4 22BIT 90UT 21 BIT 10 OUT StH 20 BIT 11 OUT CONTROL 14 START CONV.32 EOC 16 19 BIT 120UT LOGIC CONTROL AND 18 BIT 130UT 17 BIT 14 OUT (LSB) t:j=T~IM;'IN~GJ~~~~~~~~~~~~~=~==~===~t==J 10 +5V 11 DIG. GND. 12 +15V For Immediate Assistance, Dial 1-800-233-2765 15 ANA. GND. 13 ·15V 7 OVERFLOW 9ENABLE B COMP BIN 2-37 ADC·908 ABSOLUTE MAXIMUM RATINGS LIMiTS UNITS AID PERFORMANCE +15V Supply (Pin 12) -15V Supply (Pin 13) +5V Supply (Pin 10) -0.3 to +18 +0.3 to -18 -0.3 to +7.0 Volts dc Volts de Volts de AID Conversion Times +25°C o °C 10 +70 °C -55°C 10 +125 °C Digital Inputs (Pins 8, 9, 32) Analog Input (Pin 3) Lead Temp. (10 Sec.) -0.3 to +7.0 . ±25 300.max. Volts de Volts °C PARAMETERS MIN. - FUNCTIONAL SPECIFICATIONS ANALOG INPUTS MIN. Input Voltage Range - Input Impedance Input Capacitance 1 - TYP. MAX. 010 +10 010 +20 ±5 - 7 15 - - - - - UNITS Volls Volls Volls KOhms pI DIGITAL INPUTS Logic Levels Logic "I" Logic "0" Logic Loading "I" Logic Loading "0" 2.0 - - - 0.8 5 -200 Voltsdc VollSdc ~ J.IA AID PERFORMANCE Integral Non-linearity +25°C 0°Clo+70°C -55°C 10 +125 °C Differential Non·Linearity +25°C o °C to +70 °C -55 °Clo +125 °C Full Scale Absolute Accuracy +25°C. o °C 10 +70 °C -55°C 10 +125 °C Unipolar Zero Error, +25°C 010 +70 °C -5510 +125 °C Bipolar Zero Error, +25 °C (Tech Nole I) 010+70°C -5510 +125 °C Bipolar Offset Error, +25 °C (Tech Nole I) 010 +70 °C -5510 +125 °C Gain Error, +25 °C (Tech Note 1) 010 +70 °C -5510 +125 °C 2-38 MAX. UNITS - 1.0 1.08 1.15 ~ec. ~ec. ~Sec. - - - No Missing Codes (14 Bits) (13 Bits) 010 +70 °C -5510 +125 °C OUTPUTS 14 Bils Resolution Output Coding (Pin8Hi) (Pin 8 Low) Apply over theoperating temperature range and at ±15V de and +5V dc power supply voltages unless otherwise specified. TYP. Logic Levels Logic "1" Logic "0" Logic Loading "I" Logic Loading "0" Internal Reference Voltage, +25 °C Drift Exlernal Current Slraighl binary/offsel binary Complemenlary binary 2.4 - - - - 0.4 -160 6.4 - Vollsdc Volls dc ~ mA - +10.0 ±13 - +10.02 ±30 2 Voltsdc ppm! °C mA +14.25 -14.25 +4.75 +15.0 -15.0 +5.0 +15.75 -15.75 +5.25 Vollsdc Voltsdc VOllsdc - +85 -71 +80 2.7 +95 -80 +100 2.9 0.02 mA mA mA Watts %FSRI%V +9.98 - POWER REQUIREMENTS Power Supply Range +15V dc Supply -15V dc Supply +5V dc Supply Power Supply Current +15V dc Supply -15V dc Supply +5V dc Supply' Power Dissipation Power Supply Rejection - - - PHYSICAL/ENVIRONMENTAL - ±1/2 ±3/4 ±I ±3/4 ±I ±2 LSB LSB LSB - ±1/4 ±1/2 ±I ±1/2 ±3/4 ±2 LSB LSB LSB - ±0.08 ±0.18 ±0.61 ±0.122 ±0.36 ±0.85 %FSR %FSR %FSR ±0.04 ±0.07 ±O.I ±0.122 ±0.13 ±0.17 %FSR %FSR %FSR - ±0.012 ±0.07 ±0.1 ±0.04 ±0.18 ±0.3 %FSR %FSR %FSR ±0.018 ±0.12 ±0.53 ±0.061 ±0.3 ±0.73 %FSR %FSR %FSR ±0.018 ±0.12 ±0.53 ±0.12 ±O.3 ±0.73 %FSR %FSR %FSR - - - - - - Operating Temp. Range ·MC ·MM Storage Temperature Range Package Type Weight 0 -55 - - +70 +125 °C °C -65 - +150 °C 32-pin hermetic sealed, ceramic TDIP 0.42 ounces (12 grams) max. • +5V power usage at 1 TIL logic loading per data output bit. Specifications subject to change without notice. DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-11941TEL (508) 339-30001TLX 174388/FAX (508) 339-6356 ADC-908 TECHNICAL NOTES 1. Use external potentiometers to remove system errors or the small initial errors to zero. Use a 20K trimming potentiometer for gain adjustment with the wiper tied to pin 6 (ground pin 6 for operation without adjustments). Use a 20K trimming potentiometer with the wiper tied to pin 5 for zero/ offset adjustment (ground pin 5 for operation without adjustment). 2. Rated performance requires using good high-frequency circuit board layout techniques. The analog and digital grounds are not connected internally. Avoid ground-related problems by connecting the digital and analog grounds to one point, the ground plane beneath the converter. Due to the inductance and resistance of the power supply return paths, return the analog and digital ground separately to the power supplies. 3. Bypass the analog and digital supplies and the +1 OV reference (pin 1) to ground with a 4.7 J.lF, 25V tantalum electrolytic capacitor in parallel with a 0.1 J.lF ceramic capacitor. Bypass the +1 OV reference (pin 1) to analog ground (pin 15). 4. Obtain straight binar~offset binary or 2'8 complement output coding by tying C(}P BIN (pin 8) to +5V dc or leaving it open. The device has an internal pull-up resistor on this pin. To obtain complementary binary, complementary off set binary, or complementary 2's complement output coding, tie pin 8 to ground. The COMP BIN signal is compatible to CMOSITTL logic levels for those users desiring logic control of this function. 5. To enable the three-state outputs, connect ENABLE (pin 9) to a logic "0" (low). To disable, connect pin 9 to a logic "1" (high). ~~ ANALOG INPUT 6. The SAMPLE/HOLD CONTROL, pin 14, is low on power-up. The START CONVERT pulse should be given at a time delay equal to the desired acquisition time minus th...!!. 10 nanosecond delay from START CONVERT high to S/H CONTROL high. This assures the sample-hold has the minimum required acquisition time for the particular application mode. The SAMPLE/HOLD CONTROL pin goes high following the rising edge of a START CONVERT pulse and low 30 nanoseconds minimum before EOC goes low. This indicates the converter can accept a new analog input. 7. Retriggering the START CONVERT pulse before EOC goes low will not initiate a new conversion. Table 1. Input Connections INPUT PIN INPUT RANGE o to +10V o to +20 TIE TOGETHER Pin 3 Pin 2 Pin 3 ±5V Pins 2 and 4 Pins 3 and 4 Pins 2 and 1 Table 2. Zero and Gain Adjust GAIN ADJUST FS -1/2 LSB ZERO ADJUST +112 LSB FSR o to +10V Oto +20V ±5V +9.999085V +19.99817V +4.999085V +3051·N +610 J.lV +305 J.lV .5V ANALOG INPUT SETILING TIME 400 nSec MINIMUM ~: --~:~~~H~O~LD~M~O~D~E~S~ETI~L~IN=G----------------- :+7- O.1JlF 200 nSec MIN O.1IJ,F START CONVERT ---,,...-C:-~\ N 30 nSec MIN ' SAMPLE HOLD 13 15 10 11 +10VAEF BUSY N I. OUTPUT DATA --+ I ...-- 25 "Sec MIN 800 nSec MIN DATA N VALID 000 +10V INVALID --=11+- INHIBIT DELAY 10nSec MAX NOTE: NOT DRAWN TO SCALE 10 nS MAX ___ ADe-90B BIPOLAR I : 1><1 DATA N·1 VALID ~4.7}1F2 :J;.1JlF : +- 20 nSec MIN., 35 nSec MAX II+-- ENABLED DATA N VALID ANALOG INPUT +5VDC CQMPBIN ~32 ,. • 31 30 2. 28 27 26 25 2. 23 22 21 20 19 18 17 GAIN ADJUST 10 nSec MIN., 25 nSec MAX. NDEOC OUT ENAlii:E 12 StH ACO. TIME \.o---+-'---------,=-=--------~___i' :.-- SlH CONTROL OUT START CONVERT SlHCONTROL 7 16 NOTE: Times shown are guaranteed by design over operating temperature and power supply ranges. ENABLE BIT 1 (MSB) BIT 1 (MSB) 81T2 BIT3 81T4 BIT5 BIT6 BIT 7 BIT a BIT9 BIT10 BJT11 alT12 BIT 13 BIT 14 (LSB) OVERFLOW EOC 20K Figure 2. ADC-908 Timing Diagram -15V +15V ZERO/OFFSET ADJUST Figure 3. Typical ADC-908 Connection Diagram For Immediate Assistance, Dial 1-800-233-2765 2-39 ADC·908 CALIBRATION PROCEDURE 1. Connect the converter per Figure 3, and Table 1 for the appropriate full-scale range (FSR). Apply a pulse of 200 nanoseconds minimum to the START CONVERT input (pin 31) at a rate of 250 KHz. This rate is chosen to reduce flicker if LED's are used on the outputs for calibration purposes. 2. Zero Adjustments Apply a precision voltage reference source between the analog input (pin 3) and ground (pin 4). Adjust the output of the reference source per Table 2. For unipolar, adjust the zero trimming potentiometer so that the output code flickers equally betwelllLOO 0000 0000 0000 and 00 0000 0000 0001 with the COMP BIN (pin 8) tied high (straight binary) or between 11 1111 1111 1111 and 11 1111 1111 1110 with pin 8 tied low (complementary binary). Table 3, Output Coding for Unipolar Operation UNIPOLAR SCALE INPUT RANGE (Volls) 010 +10V 010 +20V OUTPUT CODING CaMP. BINARY STRAIGHT BIN. LSB MSB MSB LSB +FS-1LSB 7/8 FS 3/4 FS 1/2FS 1/4 FS 1/8 FS lLSS +9.99939 +8.7500 +7.5000 +5.0000 +2.5000 +1.2500 +0.00061 0.0000 11111111111111 11 1000 0000 0000 11 0000 0000 0000 10 0000 0000 0000 01 0000 0000 0000 00 1000 0000 0000 00 0000 0000 0001 00 0000 0000 0000 a +19.99878 +17.500 +15.00 +10.00 +5.000 +2.500 +0.00122 0.000 00 0000 0000 0000 0001111111111'1 00111111111111 01111111111111 10111111111111 11011111111111 11111111111110 11111111111111 For bipolar operation, adjust the potentiometer such that the code flickers equally between 10 0000 0000 0000 and 10 0000 0000 0001 with pin 8 tied high (offset binary) or between 01 1111 11111111 and 01 1111 1111 1110 with pin 8 tied low (complementary offset binary). Two's complement coding requires use of the MSB (pin 31) with pin 8 tied high, adjusting the potentiometer such that the code flickers between 00 0000 0000 0000 and 00 0000 0000 0001. 3. Full-Scale Adjustment Set the output of the voltage reference used in step 2 to the value shown in Table 2. Adjust the gain trimming potentiometer so that the output code flickers equally between 11 1111 1111 1110 and 11 1111 1111 1111 with pin 8 tied high (straight binary) or between 00 0000 0000 0000 and 00 0000 0000 0001 pin 8 tied low (complementary binary). Two's complement coding requires use of the MSB (pin 31) with the pin 8 tied high, adjusting the gain trimming potentiometer so that the output code flickers equally between 01 1111 1111 1110 and 01 1111 1111 1111. 4. To confirm proper operation of the device, vary the precision reference voltage source to obtain the output coding listed in Tables 3 and 4. Table 4, Output Coding for Bipolar Operation MECHANICAL DIMENSIONS INCHES (MM) +FS -1 LSB +3/4 FS +1/2FS 1.101 MAX . (28,0) 0.190 MAX ~0.010 X 0.018 ~ KOVAR Pins 17 ,16 I I I I I I I I I I I I I I I I I I BOTTOM VIEW ! 32 ~ ~0.150MIN. a -1/2FS -3/4 FS -FS +1 LSB -FS INPUT RANGE (Volls) ±5V OFFSET BIN. MSB LSB OUTPUT CODING CaMP OFF. BIN. MSB LSB +4.99939 +3_7500 +2_5000 0.0000 -2.5000 '3.7500 -4.99939 -5.0000 11111111111111 11 1000 0000 0000 11 0000 0000 0000 10 0000 0000 0000 01 0000 0000 0000 00 1000 0000 0000 00 0000 0000 0001 00 0000 0000 0000 00 0000 0000 0000 00011111111111 00 111111111111 01111111111111 10111111111111 11011111111111 11111111111110 11111111111111 TWO'S CaMP. MSB LSB 01111111111111 01 1000 0000 0000 01 0000 0000 0000 00 0000 0000 0000 11 0000 '0000 0000 10 1000 0000 0000 10 0000 0000 0001 10 0000 0000 0000 (3,8) iT 15 SPACES AT 0.100 (2,5) 1.712 MAX. (43,5) -hL 0.900 (22,9) NOTE: Pins have a 0.025 inch, ±0.01 sland-off from case. 2-40 BIPOLAR SCALE ORDERING INFORMATION MODEL NUMBER ADC-90SMC ADC-90SMM OPERATING TEMP, RANGE 0 °C to +70 °C -55°C to + 125 °C SEAL Hermetic Hermetic Receptacle for PC board mounting can be ordered through AMP Inc., Part # 3-331272-8 (Component Lead Socket), 32 required. For availability of MIL-STD-883 versions, contact DATEL. DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194fTEL (508) 339-3000fTLX 174388/FAX (508) 339-6356 ADC-914 -- PRODUCT DATA r7 FEATURES 14-Bit, High-Speed, Low-Power AID Converter - • 14-Bit resolution • 2.4 Microsecond maximum conversion time • Low-power, 925 milliwatts • Three-state output buffers • Functionally complete • Small 24-pin DIP INPUT/OUTPUT CONNECTIONS GENERAL DESCRIPTION PIN FUNCTION DATEL's ADC-914 uses an advanced design to provide a highspeed, functionally complete 14-bit AID converter in a small 24-pin DIP. The ADC-914 delivers a conversion speed of 2.4 microsecond while consuming only 925 milliwatts of power. 1 2 3 4 5 6 7 8 9 10 11 12 BIT 14 OUT (LSB) BIT 130UT BIT 12 OUT BIT11 OUT BIT 100UT BIT90UT BIT80UT BIT70UT BIT60UT BIT50UT BIT40UT BIT 3 OUT (MSB) PIN FUNCTION 13 14 15 16 17 18 19 20 21 22 23 24 ~ ENABLE EOC START CONVERT BIT20UT BIT 1 (MSB) ANALOG INPUT BIPOLAR +10V REF +15V GROUND -15V 14 ENABLE (MSB) +10V REF 2 1 1 - - - - . . - - - + + - - - - - - 1 18 BIT 1 OUT (MSB) 17 BIT 2 OUT 12BIT 30UT BIPOLAR 2 0 1 - - - - 1 ANALOG INPUT 19 11 BIT 40UT 10 BIT 5 OUT 9BIT SOUT rv~~--~~-J OIGITAL CORRECTION LOGIC 8BIT 70UT 7BIT 80UT SBIT 90UT 5 BIT 100UT 4BIT11 OUT 3 BIT 12 OUT START CONV.1S LOGIC CONTROL ANO TIMING 2 BIT 13 OUT ' - - - r - - - r - ] 1 BIT 14 OUT (LSB) EOC 15 13 22 23 24 +5V +15V GNO. ·15V Figure 1. ADC-914 Simplified Block Diagram For Immediate Assistance, Dial 1-800-233-2765 2-41 ADC-914 ABSOLUTE MAXIMUM RATINGS PARAMETERS LIMITS UNITS PERFORMANCE +15V Supply (Pin 22) -15V Supply (Pin 24) +5V Supply(Pin 13) Oto +18 Oto-18 -0.5 to +7 Voltsdc Voltsdc Voltsdc Digital Inputs (Pins 14 and 16) Analog Input Lead temp. (10 sec.) -0.3 to +7 Voltsdc -25 to +25 300 Voltsdc 'Cmax. Bipolar Zero Error +25 °C (Tech Note 1) o °C to +70 'C -55 'C to +125 'C Bipolar Offset Error +25 DC (Tech Note 1) o 'C to +70 DC -55 DC to +125 DC Gain Error +25 "C (See Tech Note 1) o DC to +70 DC -55 DC to +125 DC Conversion Time +25 DC o DC to +70 DC -55 DC to +125 DC No missing codes +25 DC o DC to +70 DC -55 DC to +125 DC FUNCTIONAL SPEelFICATIONS Apply over the operating temperature range and at ±15V dc and +5V dc unless otherwise specified. MIN. TYP. MAX. UNITS - iO.02 - ·±0.03l ±0.09 ±0.12 %FSR %FSR %FSR ±0.02 ±0.D61 ±0.12 ±0.15 %FSR %FSR %FSR - ±0.02 - - ±0.061 ±0.12 ±0.15 %FSR %FSR %FSR - - - - - - - - 2.4 2.4 2.4 14 13 12 - - 14.25 14.25 +4.75 +15 -15 +5 +15.75 -15.75 +5.25 Volts dc Volts dc Volts dc - - +20 -20 +65 925 - - +25 -28 +75 1200 ±O.01 rnA rnA rnA mW %FSR/%V 0 -55 - +70 +125 DC DC -65 - +150 DC jlSec. jlSec. jlSec. Bits Bits Bits POWER REQUIREMENTS INPUTS Analog Signal Range (See Table 5 also) Input Impedance Resistance CapaCitance Logic Levels: Logic 1 Logic 0 Logic Loading: Logic 1 Logic 0 MIN. TYP. MAX. UNITS - Oto +10 ±5 - Volts Volts 2 2.5 - KOhms pF - 2.0 - - 50 - - 0.8 Volts Volts - - - 2.5 -100 IlA IlA 14 - - Bits 2.4 - - - 0.4 Volts Volts - - - -160 6.4 rnA 10 ±5 10.02 ±30 1.5 Volts de ppm! 'C rnA OUTPUTS Resolution Logic levelS: Logic 1 Logic 0 Logic Loading: Logic 1 Logic 0 Internal Reference: +Voltage, +25' C Tempco External current 9.98 - Output Coding: - Power Supply Range +15V dc Supply -15V dc Supply +5V dc Supply Supply Current +15V Supply -15V Supply +5V Supply - TTl LOGIC LOGIC HIGH VOLTAGE TTl AD(;.HC CD405D CMOS and TIL logic are not compatible. due to different threshold levels. They can, however, be interfaced by simple techniques. The START CONVERT (Pin 21) can be driven directly from an open collector, high voltage TIL gate. Resistor Rx is used to source current and bring the TIL output up to the CMOS threshold level. Typical values of Rx are 3.3K to 10K ohms. CMOS to TTL interface requires sufficient sink current in the low state. The CD4049 (inverting) and CD4050 (noninverting) buffers, powered from +5V logic supply can accept input voltage swings of +5 to + 15V from the CMOS system. Each buffer gate can drive at least one input from any TTL family. 2-50 ORDERING INFORMATION MODEL TEMP. RANGE SEAL ADC-HC12BMC ADC-HC12BMM ADC-HC12BMM-QL Oto+70°C -55 to +125°C -55 to +125 °C Hermetic Hermetic Hermetic DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194fTEL (508) 339-3000fTLX 174388/FAX (508) 339-6356 ADC-HS12B 12-Bit AID Converter With Sample-Hold \II*H#&\#&\#&\#&\#&\#&\#&\\IIE#&\#&\#&\IIIi*[IIIi_#&\#&\#&\#&\·m· •• · . i I i l @ @ I I I ! W _ m m_ _ _1IIiliIilfuD#&\IIOOIlli@lIIimm#&\ll#&\ll#&\ll.DH. FEATURES • • • • 12-Bit resolution Internal sample and hold 6 Microseconds acquisition time 9 Microseconds conversion time Programmable input ranges Para"el & serial outputs GENERAL DESCRIPTION The ADC-HS12B is a high performance 12-bit hybrid AID converter with a self-contained sample-hold. It is specifically designed for systems applications where the sample-hold is an integral part of the conversion process. The internal sample-hold has a 6 microseconds acquisition time for a full 10V dc input change; the AID converter has a fast 9 microseconds conversion time. Five· input voltage ranges are programmable by external pin connection; 0 to +5V, 0 to+10V, ±2.5V, ±5V, and ±10V. Input impedance to the sample-hold is 100 megohms. Output coding is complementary binary for unipolar operation and complimentary offset binary for bipolar operation, with both parallel and serial outputs brought out. MECHANICAL DIMENSIONS INCHES (MM) r-(~~~\ MAX--j --L I I O.150~B)[ . ~__ 0.010 !( 0.190 (4,9) MAX I!-' U 0.160 (4,1) KOVAR 16 BOTTOM "'.Il ATO.l00EA 1.712 =~_ ..- .: ~LJ The ADC-HS12B uses a fast 12-bit monolithic DAC which includes a precision zener reference source. The circuit also contains a fast monolithic 12-bit successive approximation register, a clock and a monolithic sample-hold. PIN 1 L,-_ _ _ _ _,-' ---o...i.... ~O.900_-.J_O.l00 1--(22,8)-[ (2,5) NOTE: PINS HAVE 0.025 INCH STANDOFF FROM CASE, ±O.Ol SAMPLE CH BIPOLAR REF CONTROL OFFSET ,OUT N +15Vdc -15Vdc +5Vdc INPUT/OUTPUT CONNECTIONS PIN FUNCTION BIT 12 OUT (LS8) BIT 11 OUT G §§ ~ 12 11 ~~ ,LSB 1;;8 10 9 B 7 6 5 4 3 err NO. 2 1 ~~I- MSB, mC!i5 ,. 17 CH REF OUT BIT 10 OUT 19 CLOCK OUT BIT 9 OUT 20 E.O.C. (STATUS) BIT 8 OUT 21 BIT 7 OUT 22 COMPAR INPUT BIT 6 OUT 23 BIPOLAR OFFSET BIT 5 OUT 24 10V RANGE START CONVERT BIT'" OUT 25 20V RANGE 10 BIT 3 OUT 26 ANALOG COM " BIT 2 OUT 27 GAIN ADJ 12 BIT 1 OUT (MSB) 2. 13 SERIAL DATA OUT 29 S.H. OUTPUT 14 SHORT CYCLE 3IJ ANALOG IN 15 DIGITAL COM 31 -15V POWER 16 +5V POWER 32 SAMPLE CONTROL E.O.C. (STATUS) FUNCTION PI" +15V POWER I PARALLEL DATA OUT For Immediate ASSistance, Dial 1-800-233-2765 2-51 ADC·HS12B ABSOLUTE MAXIMUM RATINGS Positive Supply, pin 28 ........ Negative Supply, pin 31 ........ Logic Supply Voltage, pin 16 .... Digital Input Voltage, pins 14, 21, 32 .............. Analog Input Voltage, pin 30 . . .. PHYSICAUENVIRONMENTAL + 18V -18V + 5.5V Operating Temperature Range .. Storage Temperature Range .... Package Type ................ Pins ........................ Weight ...................... +5.5V ± 15V DoC to 70°C (BMC) -55 °C to +125 °C (BMM, BMM.QL) - 65°C to + 150°C 32 pin ceramic 0.010 x 0.018 inch Kovar 0.5 ounce (14 grams) FUNCTIONAL SPECIFICATIONS FOOTNOTES: Typical at 25°C, ±l5Vand +5V supplies unless otherwise noted. 1. For sample·hold input 2. All digital outputs can drive 2 TTL loads 3. For 1000 pF external hold capaCitor INPUTS Analog Input Ranges, unipolar .. Analog Input Ranges, bipolar ... Inputlmpedance' ............. Input Bias Current' ............ Start Conversion ............. 0 to + 5V, 0 to + 10V ±2.5V, ±5V, ±10V 100 megohms 50 nA typical, 200 nA max. 2V min. to + 5.5V max. positive pulse with 100 nsec. duration min. Rise and fall times <30 nsec. Logic high to low transition resets converter and initiates next conversion. Loading: 2 TTL loads Sample Control Input . . . . . . . . .. Logic high = hold Logic low = sample Loading: 1 TTL load TECHNICAL NOTES 1. It is recommended that the t15V power input pins both be bypassed to ground with a 0.01 ~F ceramic capacitor in parallel with a 1 ~F electrolytic capaCitor and the +5V power input pin be bypassed to ground with a 1 ~F electrolytic capacitor as shown in the connection diagrams. In addition, pin 27 should be bypassed to ground with a 0.01 ~F ceramic capacitor. These precautions will assure noise free operation of the converter. 2. Digital Common (pin 15) and Analog Common (pin 26) are not connected together internally, and therefore must be connected as directly as possible externally. It is recommended that a ground plane be run underneath the case between the two commons. Analog ground and t15V power ground should be run to pin 26 whereas digital ground and +5V dc ground should be run to pin 15. OUTPUTS' Parallel Output Data. . . . . . . . . .. 12 parallel lines of data held until next conversion command. VOUT ("0"):5 +OAV VOUT ("1");" +2AV Coding, unipolar .............. Complementary Binary Coding, bipolar ............... Complementary Offset Binary Serial Output Data ............ Successive decision pulses out, NRZ format. MSB first End of Conversion (status) ..... Conversion status signal. Output is logic high during reset and conversion and low when conversion is complete. Clock Output ................ Train of positive going +5V, 100 nsec. pulses at 1.5 MHz rate. 3. External adjustment of zero or offset and gain are provided for by trimming potentiometers connected as shown in the connection diagrams. The potentiometer values can be between 10K and lOOK ohms and should be 100 ppml ·C, cermet types. The adjustment range is to.5% of FSR for zero or offset and ±0.3% for gain. The trimming pots should be located as close as possible to the converter to avoid noise pickup. Calibration of the ADC-HS12B is performed with the sample-hold connected and operating dynamically. This results in adjusting out the sample-hold errors along with the AID converter. For slow throughput applications it is recommended that a 0.01 ~F hold capacitor be used for best accuracy. With this value the acquisition time becomes 25 microseconds and the external timing must be adjusted accordingly. SAMPLE-HOLD PERFORMANCE" Input Offset Drift .............. Acquisition Time, 10V to 0.01 % . Bandwidth .................. Aperture Delay Time .......... Aperture Uncertainty Time ..... ·SampletoHoldError .......... Hold Mode Droop .•........... Hold Mode Feedthrough ....... 25 ",VloC 6 ,.sec. 1 MHz 100 nsec. 10 nsec. 2.5 mV max. 200 nVI,.sec. max. 0.01 % max. 4. The recommended timing shown in the Timing Diagram allows 6 microseconds for the sample-hold acquisition and then 1 microsecond after the sample-hold goes into the hold mode to allow for output settling before the AID begins its conversion cycle. CONVERTER PERFORMANCE Resolution .................. Nonlinearity ................. Differential Nonlinearity ........ Temp. Coefficient of Gain ...... Temp. Coefficient of Zero, unipolar ................... Temp. Coefficient of Offset, bipolar .................... Differential Nonlinearity Tempco . . . . . . . . . . . . . . . . . .. Missing Codes ............... Conversion Time ............. Power Supply Rejection ........ 12 bits (1 part in 4096) ± Yo LSB max. +3A LSB max. 20 ppmloC max. ± 5. Short cycled operation results in shorter conversion times where the conversion can be truncated to less than 12 bits. This is done by connecting pin 14 to the output bit following the last bit desired. For example, for an 8-bit conversion, pin 14 is connected to bit 9 output. Maximum conversion times are given for short-cycled conversions in the Table. ± 5 ppm/DC of FSR max. t 10 ppm/DC of FSR max. ± 2 ppm/DC of FSR None over oper. temp. range 9 ,.sec. max. 0.004%1% max. POWER REQUIREMENTS Power Suppy Voltage .......... + 15V dc ± 0.5V at 20 mA -15V dc ±0.5V at 25 mA + 5V dc ± 0.25V at 85 rnA 2-52 , 6. Note that output coding is complementary coding. For unipolar operation it is complementary binary and for bipolar operation it is complementary offset binary. In cases where bipolar coding of offset binary is required, this can be achieved by inverting the analog input to the converter (using an operational amplifier connected for gain of -1.0000). The DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194ITEL (508) 339-3000ITLX 174388/FAX(508) 339-6356 ADC·HS12B mU'R) i iliful converter is then calibrated so that - FS analog input gives an output code of 0000 0000 0000, and + FS - 1 LSB gives 1111 1111 1111. IIRG CONVERT (Pin 21). The rate of the external clock must be lower than the rate of the internal clock. The pulse width of the external clock should be between 100 nanoseconds and 300 nanoseconds. Each N bit conversion cycle requires a pulse train of N + 1 clock pulses for completion, e.g., an 8-bit conversion requires 9 clock pulses for completion. A continuous pulse train may be used for consecutive conversions, resulting in an N bit conversion every N + 1 pulses, or the E.O.C. output may be used to gate a continuous pulse train for single conversions. 7. These converters dissipate 1.81 watts maximum of power. The case to ambient thermal resistance is approximately 25°C per watt. For ambient temperatures above 50°C, care should be taken not to restrict air circulation in the vicinity of the converter. 8. These converters can be operated with an extemal clock. To accomplish this, a negative pulse train is applied to START TIMING DIAGRAM FOR ADC-HS12B --fl"ji-100nsec.MIN. T_R_IG_G_ER ____ ,, 1-- -===--I SAMPLE CONTROl 6,.... STAAT CONVERT r::============-;;-;;;::-;;;;:;-=-:==========:::j E.O.C. <_ST_A_TU_S_' - - - - - - - - - - - - - - - - - - - f t - l l - - - - - - - - - - - - 9 "sec, MAX. - PARALLEL DATA NOW VALID --.....::_ 50nsec CLOCK OUT SERIAL DATA OUT I BIT 1 QUT(MSBj I I I I I I I I I I I I I I I I I : I I I I I I I I I I I ' - - - T- --- T- - - -,--- -T - - -.- ---1- - -I - - -I" - - -"1- - - -,- - --1-- - -- --- 1 - - -:- ---~----~- ---~ ---~---- ~----i- - -- ~ -- --r ----:----- +-------·0 I BIT 2 OUT I I I I I 1 I I I I I I I I , I , I I I I I :r--T,--,~-~,--TI--~,--4,--~I--r--+---- I 81T3 OUT I I BIT 12 QUT(LSB) _~...:.... __________________-"II ___ I ( I I I I I I .lI ___ .JI ____ LI 1 I I I I I ___ .!.I ___ -1I ___ -'I____ l. -+ -- -~- ---:-----;----+ -- --;---- i--.- - - - I ---~-- - - : - - - I I I I I I I , I I 1 I I I I --"1-------I I ___ ..lI ____ !..I ___ ..!I ____ lL-_''--_ __ NOTE: mIGGEA, SAMPLE CONTROL, AND STAAT CONVERT PULSES MUST BE EXTERNALLY GENERATED UNIPOLAR OPERATION, 0 TO +10V -15V +15V BIPOLAR OPERATION, ±5V +5V -15V+15V +5V '''' 'O.~ +15V 31 31 28 1.5 MEG 26 29 2. 2' ADC·HS12B 50K ! ANA.LOG IN (+5V) 0 I AOJ OFfSET 2.8 MEG 27~50K GAIN IIDJ O•01 ,.F ANALOG GND 15 AOC-HS128 l~:: I ~;~; -15V 16'4 26 29 50K -15V 28 30 +15V I "POLYSTYRENE OR TEFLON TYPE +15V "fl, 2.8 MEG 27!--o--,-J'o/',A.,-··----GAIN IIDJ O.Ol,.F L2_~r7---'T'2'-_,2-' I 50K .... CH".t 10000 pF ~ ~~~l ~TART -15V CONVERT ·POlYSTYRENE OR TEFLON TYPE For Immediate Assistance, Dial 1-800-233-2765 2-53 ADC·HS12B CODING TABLES '. UNIPOLAR OPERATION COMPo BINARY CODING MSB LSB 0000 0000 0000 0001 1111 1111 0011 1111 1111 0111 1111 1111 1011 1111 1111 1101 1111 1111 1111 1111 1110 1111 1111 1111 INPUT RANGE o TO o TO +10V +9.9976V +8.7500 +7.5000 +5.0000 +2.5000 + 1.2500 +0.0024 0.0000 +5V +4.9988V +4.3750 +3.7500 +2.5000 + 1.2500 +0.6250 +0.0012 0.0000 CALIBRATION PROCEDURE 1. Connect the ADC-HS12B as shown in one of the connection diagrams. The sample-hold and AID converter should be timed as shown in the timing diagram. The trigger pulse should be applied at a rate of 70kHz or less and should be 100 nanoseconds minimum width. 2. Zero and Offset Adjustments Apply a precision voltage reference source between the selected analog input and ground. Adjust the output of the reference source to the value shown in the Calibration Table for the unipolar zero adjustment (zero + % LSB) or the bipolar offset adjustment (- FS + % LSB). Adjust the trimming potentiometer so that the output code flickers equally between 1111 1111 1111 and 1111 1111 1110. 3. Full Scale Adjustment Change the output of the precision voltage reference source to the value shown in the Calibration Table for the unipolar or bipolar gain adjustment (+ FS - 1% LSB). Adjust the gain trimming potentiometer so that the output code flickers equally between 0000 0000 0001 and 0000 0000 0000. BIPOLAR OPERATION INPUT VOLTAGE RANGE +10V +9.9951V + 7.5000 +5.0000 0.0000 -5.0000 -7.5000 -9.9951 -10.0000 ±2.5V +2.4988V + 1.8750 +1.2500 0.0000 -1.2500 -1.8750 -2.4988 -2.5000 ±5V +4.9976V +3.7500 +2.5000 0.0000 -2.5000 -3.7500 -4.9976 -5.0000 COMPo OFFSET BINARY MSB LSB 0000 0000 0000 0001 1111 1111 0011 1111 1111 0111 1111 1111 1011 1111 1111 1101 1111 1111 1111 1111 1110 1111 1111 1111 CALIBRATION TABLE UNIPOLAR RANGE o to +5V o to +10V BIPOLAR RANGE ±2.5V ±5V ±10V ADJUST. ZERO GAIN ZERO GAIN INPUT VOLTAGE +0.6 mV +4.9982V +1.2 mV +9.9963V OFFSET GAIN OFFSET GAIN OFFSET GAIN -2.4994V +2.4982V -4.9988V +4.9963V -9.9976V +9.9927V SHORT CYCLE OPERATION 14 PIN 14 CONNECTION FOR SHORT CYCLE OPERATION RES. (BITS) PIN 14TO PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN 1 2 3 4 5 6 7 8 9 10 11 12 CONY. TIME 11 10 9 8 7 6 5 4 3 2 1 16 0.7llsec 1.3 2.0 26 3.3 4.0 4.6 5.3 60 6.6 73 90 987654321BIT FOR CONVERSION TO N erTS CONNECT THE N + 1 BIT Ol/TPUT TO THE SHORT CYCliNG TERMINAL, PIN 14 INPUT CONNECTIONS INPUT VOLTAGE RANGE o to +5V Oto +10V ±2.5V ±5V ±10V 2-54 29 29 29 29 29 CONNECT THESE PINS TOGETHER & 24 22 & 25 23 & 26 & 24 23 & 26 & 24 22 & 25 23 & 22 & 24 23 & 22 & 25 23 & 22 - ORDERING INFORMATION MODEL TEMP. RANGE ADC-HS12BMC ADC-HS12BMM ADC-HS12BMM-QL Oto+70 °C -55 to +125 °C -55 to +125 °C DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-11941TEL (508) 339-30001TLX 174388/FAX (508) 339-6356 ADC·HX, ADC·HZ Series 12-Bit, Analog-toDigital Converters i J FEATURES 12-Bit resolution S-or 20-Microseconds conversions 5 Input ranges • Internal high Z buffer • Short-cycle operation GENERAL DESCRIPTION The ADC-HX12B and ADC-HZ12B are self-contained, high performance, 12-bit AID converters manufactured with thick-and thin-film hybrid technology. They use the successive approximation conversion technique to achieve a 12-bit conversion in 20 and S microseconds respectively. Five input voltage ranges are programmable by external pin connection: 0 to +5V, 0 to +10V, ±2.5V, ±5V, and ±10V. An internal buffer amplifier is also provided for applications where 100 megohm input impedance is required. MECHANICAL DIMENSIONS INCHES (MM) 1---1.101 MAX---' I· I· I~ (28.0' I 0.'90 (4.9) MAX . ~ -r :;;;V;s'L 0.150 0.010)1 0.160 (4,1) KOVAR These converters utilize a fast 12-bit monolithic DAC which includes a precision zener reference source. The circuit also contains a fast monolithic comparator, a monolithic 12-bit successive approximation register, a clock and a monolithic buffer amplifier. Nonlinearity is specified at ±'/2 LSB maximum. 01. I ~ ~ Jg:s-. .,. Both models have identical operation except for conversion speed. They can be short-cycled to give faster conversion in lower resolution applications. Use of the internal buffer amplifier increases conversion time by 3 microseconds, the settling time of the amplifier. Output coding is complementary binary, complementary offset binary, or complementary two's complement. Serial data is also brought out. The package is a 32-pin ceramic case. +15V POWER REF -15V POWER ~~~M 1--- - (22,8) (2,5) INPUT/OUTPUT CONNECTIONS BIT 11 our BIT mOUT BO'OI.AR 15 BIT 9 OUT ~:AL BIT -1 ~~~AR~'~_"""_"-_ _ _ BIT 6 OUT 14 INPUT INPUT BIT 5 OUT ~~J o ~~A~SI 5 BIT 4 OUT 10 " ANALOG COM 17 e OUT 81T 7 OUT ~rT. .r r. . . . . . . .~ 20V 1921 CLOCK CLOCK START 12 11 10 9 8 AA Te OUT CONY LSB 7 6 5 4 SIT NO ' .712 NOTE: PINS HAVE 0,025 INCH STANDOFF FROM CASE, ±O.Ol" FUNCTION "v '"I _-j- 0.100 FUNCTION BIT 12 our (lSB) OFFSET J AT 0.,00 EA _____32...,:.... ~ 0.900 .5V POWER OUT "',IT 3 2 1 T SERIAL MBa iTsB I g~~A " " ,. BIT 3 OUT BIT 2 OUT BIT lOUT (MSBI BIT lOUT (MSB) SHQRTCYClE DIGITAL COM +5V POWER CLOCK RATE " " " " 20 REF OUT CLOCK OUT E.O.C (STATUS) START CONVERT COMPAR INPUT BIPOLAR OFFSET 10V RANGE 23 24 25 :lOV RANGE " 27 GAIN ADJ. 28 29 + 15V POWeR BUFFER OUTPUT ,. " 32 ANALOG COM BUFFER INPUT - 15V POWER SERIAL OUTPUT PARALLEL DATA OUT For Immediate Assistance, Dial 1-800-233-2765 2-55 ADC.HX, ADC·HZ FUNCTIONAL SPECIFICATIONS Typical at 2SoC, ± lSV and +SV supplies unless otherwise noted. INPUTS ADC-HX12B ADC-HZ12B Analog Input Ranges, unipolar ... Oto +SV,Oto +10VFS Analog Input Ranges, bipolar .... ± 2.5V, ± 5V, ± 10V FS Input Impedance .............. 2.5K (0 to +5V, ±2.5V) 5K (0 to + 10V, ± 5V) 10K (±10V) Input Impedance with Buffer ..... 100 Megohms Input Bias Current of Buffer ...... 125 nA typical, 250nA max. Input Overvoltage ............. '±15V Start Conversion .............. 2V min. to 5.5V max. positive pulse with duration of 100 nsec. min. Rise and fall times <30 nsec. Logic "1" to "0" transition resets converter and initiates next conversion. Loading: 2 TTL loads PHYSICAUENVIRONMENTAL Operating Temperature Range ... 0 to + 70°C or -55to +125°e Storage Temperature Range ..... -65°C to + 150°C Package Size ................. 1.700 x 1.100 x 0.160 inches Package Type ................. 32 pin ceramic Pins ......................... 0.010 x 0.Q18 inch Kovar Weight ....................... 0.5 ounces (14 grams) FOOTNOTES: 1. All digital outputs can drive 2 TTL loads. 2. Without buffer amplifier used. ADC-HZI2B may require external adjustment of clock rate. 3. FSR is full scale range and is IOV for a to + IOV or ± 5V input and 20V for ±IOV inpul. 4. Short cycled operation. OUTPUTS' TECHNICAL NOTES Parallel Output Data ............ 12 parallel lines of data held until next conversion command. VOUT ("0") :5 + OAV Vou d"l") ;;-, +2AV Coding, unipolar ............... Complementary Binary Coding, bipolar ................ Complementary Offset Binary Complementary Two's Complement Serial Output Data ............. NRZ successive decision pulses out, MSB first. Compl. Binary or Compl. Offset Binary Coding End of Conversion (Status) ...... Conversion status signal. Output is logic "1" during reset and conversion and logic "0" when conversion complete. Clock Output ................. Train of positive going +5V 100 nsec. pulses. 600 kHz for ADCHX12B and 1.5 MHz for ADCHZ12B (pin 17 grounded). 1. It is recommended that the ±15V power input pins both be bypassed to ground with a 0.01 IJ.F ceramic capacitor in parallel with a 1 IJ.F electrolytic capacitor and the +5V power input pin be bypassed to ground with a 10 IJ.F electrolytic capacitor as shown in the connection diagrams. In addition, pin 27 should be bypassed to ground with a 0.D1 IJ.F ceramic capacitor. These precautions will assure noise free operation of the converter. PERFORMANCE Resolution ................... Nonlinearity .................. Differential Nonlinearity ......... Gain Error, before adjustment .... Zero Error, unipolar, before adj. .. Offset Error, bipolar, before adj... Temp. Coeff. of Gain ........... Temp. Coeff. of Zero, unipolar ... Temp. Coeff. of Offset, bipolar ... Diff. Nonlinearity Tempco ....... No Missing Codes .............. Conversion Time', 12 bits ....... 10bils4 . . . . . . 8bils4 . . . . . . . Buffer Settling Time, 10V step .... Power Supply Rejection ......... 12 bits (1 part in 4096) ±'h LSB max. ±3;" LSB max. ± 0.10/0 ± 0.05% of FSR3 ±0.1% of FSR3 ± 20 ppm/DC max. ± 5 ppm/DC of FSR max. 3 ± 10 ppm/oe of FSR max. 3 ± 2 ppm/oe of FSR3 Over oper. temp. range 20 pSec. max. 8.0 ! 5V 15 RFEEOBACK ~ 400 _R~~--- - BIT 12 23 22 RfEEOBACJ(+400 13 OUT' . UTI TYPICAL. 'SEmlNG STEP TIME TO 1 LSB 300nsec [ 20V 10V 200nsec 5V 150nsee I 12 23 I OU.T' ·."T r n.",CAL •. SE.TT"NG. STEP Tr~~..!Q.1J:.l!!I 20V 10V 5V ~_I:'~~' .. __ j 6~~~ 400nse~. VOLTAGE OUTPUT WAVEFORMS , I n I ... I. EQUIVALENT OUTPUT CIRCUIT 4KtO.l% == - .,-_1• 2V/OIV I• _:- ,I I . I I II.~ :-c• ---I -- 10V + I\r-..J\'2'\Kl\r-017 , I 50 nsec/OIV ~~~~~~:~CK OUTPUT ' - - + - - - - . . + - - - - - 0 2 3 GROUND 1IjI ~~E(~~~~;2%l ,-----<>19 ~~~~~~:~CK +---~-----<>18 • ---- r~ t------------o21 D I' 'liiI 2V/OIV ,---"I.!'v!\r------o20 ~~~~R - - OAC-HF with AM-500. ±5V output full scale (1 OV) step HIGH SPEED INPUT REGISTER ORDERING INFORMATION DAC·HF DATA -:5"sm'n:~ LOADED - : 3-4 _ \ 7"s MODEL OPERATING TEMP. RANGE SEAL DAC-HF8BMC DAC-HF8BMM DAC-HF8/883B Oto +70 °C -55 to +125 °C -55 to +125 °C Hermetic Hermetic Hermetic DAC-HF10BMC DAC-HF10BMM DAC-HF10/883B Oto +70 °C -55 to +125 °C -55 to +125 °C Hermetic Hermetic Hermetic DAC-HF12BMC DAC-HF12BMM DAC-HF12/883B Oto+70°C -55 to +125 °C -55 to +125 °C Hermetic Hermetic Hermetic I lmn l---- DATEL. Inc. 11 Cabot Boulevard. Mansfield. MA 02048-1194rrEL (508) 339-3000rrLX 174388/FAX (508) 339-6356 DAC-HK Series 12-Bit Hybrid DAC's with Input Register n FEATURES 12-8it resolution 20 ppm/DC Tempeo • Input register • 2 Coding options • Fast settling time GENERAL DESCRIPTION The DAC-HK Series hybrid D/A converters are high performance 12-bit devices with a fast settling voltage output. They incorporate a level controlled input storage register and are specifically designed for systems applications such as data bus interfacing with computers. When the "load" input is high, data in the storage register is held and when the load input is low, date is transferred through to the DAC. There are two basic models available by coding option: binary, and two's.complement. The output voltage ranges are externally pin-programmable and include: 0 to +2.5V, 0 to +5V, 0 to +10V, ±2.5V, ±5V, and ±10V. MECHANICAL DIMENSIONS INCHES (mm) 0.800MAX (20,3) 0.190 MAX ~ ~ 0.010 X 0.018 ~ KOVAR Pins 12 The DAC-HK Series contains a precision zener reference circuit. This eliminates code-dependent ground currents by routing current from the positive supply to the internal ground node a determined by the R-2R ladder network. The internal feedback resistors for the on-board amplifier track the ladder network resistors, enhancing temperature performance. The excellent tracking of the resistors results in a differential nonlinearity tempco of 2 ppm/DC maximum. The temperature coefficient of gain is 20 ppm/DC maximum and tempco of zero is ±3 ppm/DC maximum. 13 11 SPACES ATO.l00 (2,5) BOTTOM VIEW 24 '--------' L I 0.150 MIN. (3,8) 1.310 MAX. (33,3) --hL 0.600 (15,2) NOTE: Pins have a 0.025 inch, ±0.01 stand-off from case. REF. GAIN BIP. OUT ADJUST OFFSET -Vs +5V INPUT/OUTPUT CONNECTIONS PIN SUM. JUNCTION +5V 1 2 3 4 5 6 7 ~ 9 10 II 12 1 2 3 (MSB) 4 5 6 7 BIT 8 FUNCTION PIN FUNCTION BIT 1 IN (MS61 BIT 2 IN BIT31N BIT41N BIT 51N BIT 61N BIT 71N tll HIN BIT91N BIT lOIN BIT II IN BIT 12 IN (L~tl 13 14 15 16 17 18 19 20 21 22 23 24 +5VDC 15VD OUTPUT LOAD BIPOLAR JI-F 10V HANGE 20V RAN E UNCIIUN R UND +15VDC GAIN ADJ REF OUI 9101112 (LSB) For Immediate ASSistance, Dial 1-800-233-2765 3-5 DAC-HK Series .. ABSOLUTE MAXIMUM RATINGS Positive Supply, pin 22 ..••.• Negative Supply, pin 14 .••.• Logic Supply, pin 13 .••••••• Digital Input Voltage, pins 1-12& 16 .............. . Output Current, pin 1S ., •...• DAC-HK12B PHYSICAL/ENVIRONMENTAL +18V -18V +S.2SV Operating TemperatureRange • +S.5V ±20 rnA Storage Temperature Range • Package Type .••.....•.••• Pins ..................... Weight ................... FUNCTIONAL SPECIFICATIONS Typical at 2S"C, ±'SV and+5V supplies unless otherwise noted. O°C to + 70°C (BGC, BMC) -55 'Cto + 125 'C bBMM/883B) -65°C to +125° 24-pin Ceramic DIP 0.010 x 0.018 inch Kovar 0.2 ounces (6 grams) FOOTNOTES: 1. For two's complement coding order the model described under ordering information. 2. Logic levels are the same as for data inputs. 3. By external pin connection. 4. For ± 12V dc. +5V dc operation. contact factory. INPUTS Resolution .••••••••••••.•• Coding, unipolar output •••• ; Coding, bipolar output •..••. Input Logic Level, bit ON ("1") ................... Input Logic Level, bit OFF ("0") •..•.••.•...•..•.. Logic Loading ............. LoadlnpuP ............... Load Input Loading •••••.••• 12 bits Straight Binary Offset Binary Two's Complement' +2.0V to +5.5V OV to +0.8V 1 LSTTL load High ("1 ") = hold data Low ("0") = transfer data 3 LSTTL loads OUTPUT Output Voltage Ranges3, unlpolar, ................ Output Voltage Ranges', bipolar ••.••••••••••.••• Oto +10V ±2.5V ±5V ±10V Output Current ;.; ..•.•••.• ±5 rnA min . Output Impedance •.•••.••• • 0.05 ohm PERFORMANCE linearity Error, max •........ Differential linearity Error, max.................... Gain Error, before trimming .• Zero Error, before trimming .• Gain Tempeo, max ••........ Zero Tempeo, unipolar, max.................... Offset Tempeo, bipolar, max.................... . Diff. Linearity Error Tempeo, max •••.••.••••.•.•.•••• Monotonicity .•••••.•..•... Settling Time, 5V change .•.. Settling Time, 10V change ... Settling Time, 20V change.•.• Settling Time, 1 LSB change. Slew Rate .••.•••.••..•.•.• Power Supply Rejection ..••• tv. LSB ±3I4LSB ±0.10J0 ±O.OS% ±20 ppm/oC ± 5 ppm/oC of FSR ± 10 ppm/oC of FSR ± 2 ppm/oC of FSR Guarallteed over oper. temp. range 3 ,.sec. 3,.sec. 4,.sec. 800 nsec. 2OV/p.sec. ± 0.002% FSR/oJb TECHNICAL NOTES 1. It is recommended that these converters be operated with local supply bypass capacitors of 1 fl-F (tantalum type) at the + 15, - 15, and + 5V supply pins. The capacitors should be connected as close to the pins as possible. In high RFI noise environments these capacitors should be shunted with 0.01 fl-F ceramic capacitors. 2. The analog, digital, and power grounds should be separated from each other as close as possible to pin 21 where they all must come together. 3. The "load" control pin is a leveltriggered input which causes the register to hold data with a high input and transfer data to the· DAC with a low input. 4. A setup time of 50 nanoseconds minimum must be allowed for the input data. The DAC output voltage begins to change when the register output changes. 5. The external gain adjustment shown in the Connection Diagrams has a range of ± 0.2% of full scale. If a wider range is desired the 18-Megohm resistor can be decreased slightly in value. The fUll-scale output is typically accurate within ± 0.1 % with no adjustment. The zero, or .offset, adjustment has a range of ± 0.35% of FS. 6. If the reference output terminal (pin 24) is used, an operational amplifier in non-inverting mode should be used as a buffer. Current drawn from pin 24 should be limited to ± 10 ~ in order not to affect the T.C. of the reference. POWER REQUIREMENTS Power Supply Vohage 3-6 ...... + lSVdc ±0.5V dc at 10 rnA _15V dc ± 0.5V dc at 25 rnA +5V dc ±0.25V dc at 35 rnA ± 12V dc, + 5V operation' DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 0204B-1194ITEL (SOB) 339-S000ITLX 17438B/FAX (508) 339-6356 DAC·HK Series iii TIMING DIAGRAM Hold LOAD DATA ~~~~----~ X IN ~O _ _..J. I I 'LJ I I I I I ~Ii\ !I ! l! I I I tsetup I I I I I I I- 50 nsec.min.-.j J-+- I !I tsetup I 50 nsec.min. ~ I I 11 l REGISTER OUTPUT TO DAC I --Jt PHL I I -lt60 nsec.I-- I- PLH 60 nsec. All rise and fall times';; 10 nsec. CONNECTION DIAGRAMS BIPOLAR OPERATION UNIPOLAR OPERATION (0 to +10V) (±5 V) LOAD LOAD BIT BIT LSB 12 " 10 " " 10' t5VDC 13 14 LSB -15VDC OUT to TO +10VI 15 16 12 12 13 " " 14 10 10 15VOC ( ·5 TO t5VI 17 I. IB I. DATA 7 IN 6 lOOK ZERO 'ADJ. 20 18 2OI--o-~_'\NV'v...< ""I--o--I--~---~ 21 22 lOOK GAIN 23 MSB ADJ. 24 23I--o--I--4-~~N~-..~~~~ MSB 24 1 ADJ +15VDC 20 5K .. 15VDC OUTPUT RANGE SELECTION OUTPUT CIRCUIT FULL SCALE lout ~ 2 rnA (BINARYI t5VDC OUT 16 17 DATA IN 1--0--1---....- - - - . 15 SUM. JUNCTION 5K 19 20V RANGE 18 lOV RANGE 15 OUTPUT 5K 17 BIPOLAR OFF. RANGE ±10V ±5V ±2.5V +10V +5V CONNECT THESE PINS TOGETHER 15 & 15 & 15& 15& 15& 19 18 18 18 18 17 17 17 17 17 &20 & 20 &20 & 21 & 21 19 & 20 19&20 24 REF. OUT 21 For Immediate Assistance. Dial 1-800-233-2765 GROUND 3-7 DAC·HK,'Series CODING TABLES UNIPOLAR OPERATION STRAIGHT BINARY LSB MSB 1111 1111 1100 0000 1000 0000 0100 0000 0000 0000 0000 0000 1111 0000 0000 0000 0001 0000 BIPOLAR OPERATION o +9.9976 +4.9988 +5.0000 +2.5000 +0.0024 0.0000 +3.7500 +2.5000 +1.2500 +0.0012 0.0000 + 7.5000 TWO's COMPLEMENT OFFSET BINARY OUTPUT RANGES 010 +10V to +5V MSB LSB 111111111111 1100 0000 0000 1000 0000 0000 0100 0000 0000 0000 0000 0001 0000 0000 0000 MSB LSB 0111 1111 0100 0000 0000 0000 1100 0000 1000 0000 1000 0000 1111 0000 0000 0000 0001 0000 OUTPUT RANGES ±'0V +9.9951 +5.0000 0.0000 -5.0000 -9.9951 -10.0000 ±5V +4.9976 +2.5000 0.0000 -2.5000 -4.9976 -5.0000 ±2.5V +2.4988 + 1.2500 0.0000 -1.2500 -2.4988 -2.5000 APPLICATIONS INTERFACING TO ~ INTERFACING TO 8 BIT DATA BUS 12 BIT DATA BUS -.------_..- I I I I i _4 ....., ••••••• A\ ADDRESS STROBE WRITE STROBE CALIBRATION PROCEDURE Select the desired output voltage range and connect the converter up as shown in the Output Range Selection Table and the Connection Diagrams. Refer to the Coding Tables. UNIPOLAR OPERATION 1. Zero Adjustment. Set the input digital code to 0000 0000 0000 and adjust the ZERO ADJ. potentiometer to give O.OOOOV output. 2. Gain Adjustment. Set the input digital code to 1111 1111 1111 (straight binary) and adjust the GAIN ADJ. potentiometer to give the full·scale output voltage shown in the Coding Table. BIPOLAR OPERATION 1. Offset Adjustment. Set the digital input code to 0000 0000 0000 (offset binary) or 1000 0000 0000 (two's complement) and adjust the OFFSET ADJ. potentiometer to give the negative full-scale output voltage shown in the Coding Table. 2. Gain Adjustment. Set the digital input code to 1111 1111 1111 (offset binary) or a 0111 1111 1111 (two's complement) and adjust the GAIN ADJ. potentiometer to give the positive full-scale output voltage shown in the Coding Table. 3-8 ORDERING INFORMATION OPERATING TEMP. RANGE SEAL Oto +70 °C Oto +70 °C -55 to +125 °C -55 to +125 °C Epoxy Herm. Herm. Herm. 2's Complement Coding DAC-HK12BGC-2 0 to +70 °C DAC-HK12BMC-2 0 to +70 °C DAC-HK12BMM-2 -55 to +125 °C DAC-HKB-2/883B -55 to +125 °C Epoxy Herm. Herm, Herm. MODEL NO. Binary Coding DAC-HK12BGC DAC-HK12BMC DAC-HK12BMM DAC-HKB/883B The MIL-STD-883B units are available under DESC Drawing Number 5962-89528. DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194ITEL (508) 339-3000ITLX 174388/FAX (508) 339-6356 DAC-HP16B 16-Bit, Micro-electronic Dig ital-to-Analog Converter - ! IWI FEATURES 16-Bit binary model Voltage outputs • 15 ppm/oC Maximum gain tempco Linearity to ± 0.003% GENERAL DESCRIPTION The DAC-HP series are high resolution hybrid D/A converters with voltage output. They are self-contained, including a low tempco zener reference circuit and output operational amplifier, all in a miniature 24-pin double spaced ceramic DIP package. The DAC-HP16B has 16-bit binary resolution with ±O.003% linearity. Input. coding is complementary binary and complementary offset binary for the DAC-HP16B. This device operates in both unipolar and bipolar modes with output voltages of 0 to +1OV dc and ±5V dc respectively. Binary versions with a bipolar output voltage range of ±10V dc are available, denoted by the suffix "-1" after the model designation. MECHANICAL DIMENSIONS INCHES (MM) I f-0~~,AX-l ~=r 0.190 MAX (4.8) o 150MIN (3.BI ~ 1 OOTQl(0018 KOVAR I 13. .12 L 0600--1 [- (15.2) I 1__ I 0.100 (2,5) NOTE: PINS HAVE 0.025 INCH STANDOFF FROM CASE, ±O.Ol" INPUT/OUTPUT CONNECTIONS >---_---@OUTPUT PIN 1 2 3 4 5 6 7 8 9 10 11 12 BIT 1 2 3 lASS 4 5 6 7 8 PIN FUNCTION 13 14 15 16 17 18 19 20 21 22 23 24 BIT 131N BIT 141N BIT 151N BIT 161N (LSB) OUTPUT BIPOLAR OFF 15VDC GROUND SUM JUNCTION GAIN ADJ +15VDC REF OUT 9 10 11 12 13 14 15 16 DIGITAL INPUTS For Immediate Assistance, Dial 1-800-233-2765 FUNCTION BIT 1 IN (MSB) BIT 21N BIT 31N BIT 41N BIT 51N BIT61N BIT 71N BIT81N BIT91N BIT 10 IN BIT 11 IN BIT 121N LSS 3-9 DAC·HP16B ABSOLUTE MAXIMUM RATINGS Positive Supply, pin 23. . . . . .. + laV Negative Supply, pin 19 ...... -laV Digitallnput Voltage, pins 1-16 + 5.5V Output Current, pin 17 . . . . . .. ± 20 rnA FUNCTIONAL SPECIFICATIONS Typical at 25·C, and ± 15V supplies unless otherwise noted. TECHNICAL NOTES 1. It is recommended that these converters be operated with local supply bypass capacitors of 1 !'F (tantalum type) at the + 15V and - 15V supply pins. The capacitors should be connected as close to the pins as possible. In high frequency noise environments an additional 0.01 /IF ceramic capacitor should be used in parallel with each tantalum bypass. 2. When laying out the circuit board for this device, isolate the analog, digital, and power grounds as much as possible from each other before joining them at pin 20. INPUTS Resolution ................ Coding, unipolar output ...... Coding, bipolar output ....... Input Loyie Level, bitON "0")' ............. Input Logic Level, bit OFF ("1 ")' ............ Logic Loading .............. 16 bits Compo Binary Camp. Off. Binary OV to +0.8V at -1 mA +2.4V to +5.5V at +40 pA 1 TTL load OUTPUTS Output Voltage Range, Unipolar' ................ Output Voltage Range, Bipolar .................. Output Voltage Range, "-1" Suffix ............. Output Current, min." ........ Output Impedance .......... Oto +10V ±5V ±10V ±5 rnA 0.05 ohm 3. The external gain adjustment shown in the diagrams gives an adjustment of ± 0.2% of full-scale range. The converters are internally trimmed to ± 0.1 % at full scale. A wider range of adjustment may be achieved by decreasing the value of the the 510 Kohm resistor. 4. The zero adjustment, or offset adjustment, has an adjustment range of ± 0.35% of full-scale range. The unipolar zero is internally set to zero within ± 0.1 % of full-scale range. 5. If the reference output (pin 24) is used, it must be buffered by an operational amplifier in the noninverting mode. Current drawn from pin 24 should be limited to ± 10 t- FULL SCALE lOUT = 2mA (Binary) 21 SUM. JUNC. 5K' ">----+-----0 17 OUTPUT r---~V\/\r---() 18 BIPOLAR OFF. + - - - - - - - - - - ( ) 24 REF. OUT + 6.4V REF. + - - - - - - - - - - ( ) W GROUND 10K FOR -1 MODELS ORDERING INFORMATION MODEL NO. OPERATING TEMP. RANGE SEAL DAC-HP16BMC DAC-HP16BMM DAC-HPB/883B DAC-HP16BMC-1 DAC-HP16BMM-1 DAC-HPB-l/883B Oto +70 °C -55 to +125 °C -55 to + 125°C Oto +70 °C -55 to +125 °C -55 to +125 °C Herm. Herm. Herm. Herm. Herm. Herm. DAC-HP16BGC-1 DAC-HP16BGC Oto+70°C Oto +70 °C Epoxy Epoxy The MIL-STD-883B units are available under DESC Drawing Number 5962-89531. For Immediate Assistance, Dial 1-800-233-2765 3-11 Contact DATEL for your Data Acquisition component needs. Dial 1-800-233-2765 for Applications Assistance 3-12 DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194fTEL (508) 339-3000rrLX 174388/FAX (508) 339-6356 DAC-HZ Series 12-Bit Hybrid Digital-to-Analog Converters FEATURES • • • • • 12-Bit binary 5 Output ranges 3 Microseconds settling time Internal reference and output amplifier High performance GENERAL DESCRIPTION The DAC-HZ Series are high performance, hybrid 12-bit binary digital-to-analog converters. These converters are manufactured using thin- and thick-film technology. They are complete and self-contained with a precision internal reference and fast output operational amplifier. Pinprogrammable output voltage ranges are provided for a high degree of application flexibility; the output voltage ranges are 0 to ±5V dc, 0 to +1OV dc, ±2.5V dc, -5V dc, and ±10V dc. Current output is also provided. MECHANICAL DIMENSIONS INCHES (MM) I MSS 1 2 3 4 5 6 7 8 9 10 11 12 LSB • I 3E~~~~~~~~~~===I~ < The DAC-HZ Series contains a precision zener reference circuit. This eliminates code-dependent ground currents by routing current from the positive supply to the internal ground node as determined by the R-2R ladder network. The internal feedback resistors for the on-board amplifier track the ladder network resisters, enhancing temperature performance. The excellent tracking of the resistors results in a differential nonlinearity tempco of 2 ppm/DC maximum. The temperature coefficient of gain is 20 ppm/DC maximum and tempco of zero is ±3 ppm/DC maximum. BIT 1.290 MAX (32,77) .. PIN 1 'DENT. ---L O.190(4,8)MAX r_---=====----.,~050(1.27) T ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ :=E'50!3.•,) --1 f-;'00(2,~~.018(O.46) ALL DIMENSIONS ARE IN INCHES (MM) NIC 0®®00®0®0@@@ @ INPUT/OUTPUT CONNECTIONS 5KO I I 0" CONVERTER 1 SKU J 20V @ 'uv RANGE @ cuRRENT @JOUT . REFERENC E INPUT vo @ @7 -'VVVV'BlPOlAR OFFSET 631 ---j------"N'v-~~IOK ~g; lOOK _15V C [0001 TOOOI "F) GAIN ADJ MSB 2.BMEG 1 10K TO lOOt< GAIN ADJ 10K TO lOOK CODING TABLES UNIPOLAR OUTPUT BINARY INPUT CODE MSB 0000 0011 0111 1011 1111 1111 0000 1111 1111 1111 1111 1111 BIPOLAR OUTPUT COMPLEMENTARY OFFSET BINARY COMPLEMENTARY BINARY INPUT CODE UNIPOLAR OUTPUT RANGES LSB OTO +10V o TO +5V OTO -2mA MSB 0000 1111 1111 1111 1110 1111 +9.9976V + 7.5000 +5.0000 +2.5000 +0.0024 0.0000 +4.9988V +3.7500 +2.5000 + 1.2500 +0.0012 0.0000 -1.9995 mA -1.5000 -1.0000 - 0.5000 -0.0005 0.0000 0000 0011 0111 1011 1111 1111 BIPOLAR OUTPUT RANGES LSB 0000 1111 1111 1111 1111 1111 0000 1111 1111 1111 1110 1111 ±10V +9.9951V + 5.0000 0.0000 -5.0000 - 9.9951 -10.0000 ±5V +4.9976V + 2.5000 0.0000 - 2.5000 - 4.9976 -5.0000 ±2.5V +2.4988V + 1.2500 0.0000 -1.2500 - 2.4988 -2.5000 ±1 mA -0.9995 mA - 0.5000 0.0000 + 0.5000 + 0.9995 + 1.0000 EQUIVALENT CURRENT MODE OUTPUT CIRCUIT 6.3k VO UT "t2.5V MAXIMUM lOUTPUT VOL T AGE COMPLIANCE I .'OUT OAC·HZI2B i VOUT SKU 80n REa = AO = 5K for unipolar operation = RR II Ro = 2.B K Rea for bipolar opera'ion 'OUT = 2mA binary For Immediate Assistance, Dial 1-800-233-2765 3-15 DAC-HZ Series USE OF HIGH SPEED EXTERNAL OP AMP FOR FASTER SETTLING Reier to the Output Range Selection Table. 11 BIPOLAR OFFSET Where pin 15 appears P,,, 20 0,21 use pin X of external DAC·HZ12B 18 10 v. RANGE 19 20 V. RANGE amplil ier and scale as desired ~~~CU~R~R~.~NT~O~U~T~______'04U~T____--1 AI = EXTERNAL HIGH SPEED INVERTiNG OPAMP.. USE DATEI AM-SO~ FOR LESS THAN 1.0~SEC OUTPUT SETTLING PRECISION, LOW COST BASE LINE RAMP GENERATOR '2 1281T BINARY DAe· HZ12B COUNTER RATE ADJUST RESET +1011 C.O''''' THIS CIRCUIT DEVELOPS A HIGHLY LINEAR OUTPUT VOLTAGE RAMP FROM a TO +10V. THE RAMP CAN 8E MADE AS SLOW AS DESIRED WITHOUT AFFECTING LINEARITY BY SeTIING THE PULSE RATE OF THE TIMING CIRCUIT TO THE PROPER EXTREMELY LINEAR OUTPUT VALUE. THE OUTPUT. RAMP IS GENERATED IN DISCRETE STEPS OF .024" fS IC098 STEPS FOR FSCHANGEI. ~~----------------- 1-- ORDERING INFORMATION MODEL NO. DAC-HZ12BGC DAC-HZ12BMC DAC-HZ12BMM DAC-HZ12DGC DAC-HZDMC DAC-HZ12DMM DAC-HZ12DMM-QL DAC-HZB/883B 3-16 OPERATING TEMP. RANGE o to +70 °C oto +70 °C -55 to +125 °C Oto +70 °C Oto +70 °C -55 to +125 °C -55 to +125 °C -55 to +125 °C SEAL Epoxy Herm. Herm. Epoxy Herm. Herm. Herm. Herm. SAMPLE HOLD AMPLIFIERS Linearity Model (Ok) Acquisition Time Aperture Delay Aperture Jitter Bandwidth Hold Mode (MHz) Droop Case Page SHM-HU 0.1 25 ns 6 ns 10 ps 50 50 IJV/lJs 24-Pin DIP 4-23 SHM-7 0.1 40 ns 3 ns 10 ps 40 100 IJV/IJS 24-Pin DIP 4-17 SHM40 0.1 40 ns 3 ns 10 ps 40 100 IJV/IJS 24-Pin DIP 4-5 SHM-6 0.02 2IJs 20 ns 2 ns 5 10 IJV/IJS 32-Pin DIP 4-15 New SHM-43 0.01 35 ns 5 ns 1 ps 150 5IJV/IJs 24-Pin DIP 4-7 Preliminary SHM-49 0.01 140 ns 6 ns 15 ps 16 1 IJV/IJS 8-Pin DIP 4-25 SHM-45 0.01 200 ns 6 ns ±50 ps 16 0.51JV/lJs 24-Pin DIP 4-11 SHM-4860 0.01 200 ns 6 ns ±50 ps 16 0.51JV/lJs 24-Pin DIP 4-13 SHM-30 0.01 500 ns -25 ns 0.1 ns 4.5 0.01 IJV/IJS 14-Pin DIP 4-3 SHM-20 0.01 1IJs 30 ns 1 ns 2 0.81JV/lJs 14-Pin DIP 4-1 SHM-91 0.003 2IJs 15 ns 300 ps 2 5IJV/IJs 24-Pin DIP 4-19 New SHM-945 0.0004 500 ns 5ns 10 ps 12 0.51JV/lJs 24-Pin DIP 4-21 Advanced MSH-840* 0.01 750 ns 6 ns ±1 ns llJV/lJs 32-Pin DIP 4-27 • QUAD Simultaneous Sample-Hold with 4-Channel Multiplexer For Immediate Assistance, Dial 1-800-233-2765 4-i Contact DATEL for your Data Acquisition component needs. Dial 1-800-233-2765 for Applications Assistance 4·ii DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194fTEL (508) 339-3000fTLX 174388/FAX (508)339-6356 SHM-20 High-Speed, 0.010/0 Monolithic Sample-hold 7tH 1m 71i1 Ii iii!! i FEATURES Internal hold capacitor 1 Microsecond acquisition time 1 Nanosecond aperture uncertainty • 0.01% Accuracy • 0.08 MicroV/microsecond droop rate Differential inputs GENERAL DESCRIPTION DATEL's SHM-20 is a low-cost, complete monolithic sample-hold amplifier which includes an internal 100 pF MOS hold capacitor. Primarily designed for high-speed analog signal processing applications, the SHM-20 features a typical acquisition time of 1.0 microsecond for a 10V input step to 0.01%. Aperture uncertainty is typically 1 nanosecond and droop rate is as low as 0.08 ~Vlmicr05econd. MECHANICAL DIMENSIONS INCHES (MM) MAX. "j _ o . 7 9(20.1) 0 1 TYPICAL SAMPLE AND HOLD PERFORMANCE AS FUNCTION OF HOLDING CAPACITOR DRIFT CURRENT VS. TEMPERATURE '0 1000 c" ' 100 of. INTERNAL / .-.-----------~ ~ 1.0 ,00 0.5 "' ~ ~ 1-'>.-.-+.......--"'::=;::==:; '0 0.' '0 .05 --------I--- I -25 I I r--->,J----'t--..., r---t'<-'--+"'<--"" 0.023 (a,S) 0.100 (2,54) I 0 +25+50+75-tl00+12b 100 '000 'OK 100K eli VALUE, PICOFARADS TEMPERATURE, °C INPUT/OUTPUT CONNECTIONS OFFSET ADJUST .0. -INPUT 2 3 + INPUT OFFSET ADJUST • 5 • • 7 GND EXT HOLD REF GND For Immediate Assistance, Dial 1·800-233-2765 INT COMP FUNCTION I OFFSET ADJUST -Vs REFERENCE GROUND OUTPUT INTEGRATOR COMPENSATION 9 1O +Vs NO CONNECTION "12 NO CONNECTION '3 SUPPLY VOLTAGE GROUND " 8tH CONTROL EXTERNAL HOlD CAPACITOR 4-1 SHM·20 q ABSOLUTE MAXIMUM RATINGS Voltage between Supply Pins (9 & 5) ........................ 40V Differential Input Voltage ......................................... ±24V Digital Input Voltage, Pin 14 ............................. +8 to -15V Output Current, Continuous1 ............................... ±20 rnA Footnotes 1. 2. 3. 4. 5. FUNCTIONAL SPECIFICATIONS 6. 7. 8. Typical at +25 "C, ±15V dc, using internal hold capacitor, unless otherwise noted 9. Internal power dissipation may limit output current below +20 mAo Over full operating temperature range. Cannot tolerate even a momentary short circuit to ground or either supply. Voltage gain =+1 Voltage gain =+1, load resistance =1 kQ, load capacitance =50 pF, output volt· age = 100 mV P·P. Input voltage = OV, digital input voltage = 3.5V. Output voltage = 10V step. A power supply voltage as low as ±12V may be used. However, this will cause some degradation in performance. For CH =100 pF. For CH =1000 pF Pedestal Error is 0.1 mY. For CH = 0.011J.F Pedestal Error is 0.01 mY. ANALOG INPUTS Input Voltage Range2, min ........................................................................ ±10V Input Impedance, min............................................................................... 1 MQ Input Capacitance, max .............................................................................. 3 pF Input Offset Vonage, max ......................................................................... 1 mV Input Offset Voltage Drift, max ...........................................................20 1lV! "C Input Bias Current, max..........................................................................300 nA In~ut Offset Current, max .................................. ,....................................300 nA TECHNICAL NOTES DIGITAL INPUTS2 2. If an external hold capacitor (CH) is connected to pins 7 and 11 , then a noise bandwidth capacitor with a value of 10% of the value of the external hold capacitor should be connected from pin 8 to signal ground, pin 6. Exact value and type are not critical. Logic Level High, VIN ("1 ") min., Hold Mode .................................................................................................2.DV Logic Level Low, VIN ("0"), max, Sample Mode...................... ,.....................................................................0.8V High Levellnut Current, max...................................................................0, 1 IJ.A Low Level Input Current, max..................................................................10 IJ.A OUTPUT Output Voltage Range2, min .................................................................... ±10V Output Current2, min •............................................................................ ±1 0 mA Output Impedance, Hold Mode2 .................................................................. 1Q PERFORMANCE Accuracy ...................................................................................................0.01% DC Gain, min ..................................................................................... 3 x 105 VN Gain Accuracy! ....................................................................... 0.5 x 10.4% FSR Gain Error Tempco ....................................................................... ±D.6 ppm/ "C Gain Bandwidth Product5 ...................................................................... 2 MHz Hold Mode Feedthrough, 10V p.p, 100 KHz2 ................................................................................. 2 mV Droop Rate ............. ;.......................................................................... 0.08IlV/fIS Droop Rate2 ........................................................................................ 1.2IlV/fIS Charge Transfe~ ...................................................................................... 0.1 pc Pedestal Error9......•..........................•........•.......................•...•.................... 1 mV Total Output Noise, DC to 10 MHz, max...................................... 200 IlV RMS Power Supply Rejection Ratio min. +VS .........................................................................................................80 dB ·VS ..........................................................................................................65 dB DYNAMIC CHARACTERISTICS Acquisition Time, 10V to 0.1% ............................................................................................0.8f1S 10V to 0.01% ..........................................................................................1.0flS Aperture Delay Time ................................................................. 30 nS Aperture Uncertainly Time ...........................,............................................. 1 nS Aperture Time ............................................................................................25 nS Hold Mode Settling Time, 0.01 W .......................................................... 185 nS Rise Time ..................................................................................................100 nS Overshoot ....................................................................................................15% Slew Rate7 ..............••...•.......•........•.....•....................•...........•....•.......•..... 45 V/fIS 1. A printed circuit board with ground plane is recommended for best performance. The supply pins (pins 5, 9) should be bypassed to ground with a 0.01 to 0.1 I1F ceramic capaCitor as close to the pins as possible. 3. The Hold Capacitor (CH) should have high insulation resistance and low dielectric absorption to minimize droop error. For operating temperatures up to +70 °C, polystyrene dielectric is a good choice. Any PC connections to the hold capaCitor terminal (pin 11) should be kept short and "guarded" by the ground plane to avoid errors due to drift currents from nearby signal lines or power supply voltages. 4. The offset adjust may be used to eliminate the pedestal error by connecting a 10K ohm pot between pins 3 and 4 and connecting the wiper to the -15V supply, pin 5. OPEN LOOP GAIN ANO PHASE RESPONSE 120 ""- ~ ""- """80 1""- ........ ""- ""eo ""- ""Gain ...... 100 45 100 90 -...... (CH = 100 pF) ....... Gain ...... \. \ 1-... 'l lK 10K lOOK w 0 ui Ul 135 -____..,1 1-1:.:2'--_ _....1 8 StH StH OUTPUT SHM-43 -U- • Connections shown for StH. if opposite polarity sample hold command is desired. connect pin 6 to +5V (pin 4). Using opposite polarity. StH command will not effect speed or accuracy. • The SHM-43 has been optimised for driving 100n loads.R1 should be chosen so that the total load on the StH is loon. TEST METHOD +5V StHCOMMAND I SAMPLEI HOLD OV(GND) +IV ANALOG INPUT -IV , , ACQUISITION : TIME: , 25 nS ' , 0.01% , .... _. +IV SAMPLE HOLD OUTPUT -IV , FEEDTHRU 82 dB 20 nS ' . 0.01% , , ,.,.25 nS ~ ,, 0.01% ' ORDERING GUIDE MODEL NUMBER TEMP. RANGE SHM-43MC SHM-43MM Oto +70 °C -55 to +125 °C Contact DATEL for availability of MIL-STD-883 versions. For Immediate Assistance. Dial 1-800-233-2765 4-9 Contact DATEL for up-to-date information on products covered by "Advanced" and i'Preliminary" product data sheets. Dial 1-800-233-2765 for Applications Assistance 4·10 DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194fTEL (508) 339-3000fTLX 174388/FAX (508) 339-6356 SHM-45 High-Speed Hybrid Precision Sample-hold FEATURES Ideally suited for DATEL's Ultra-fast ADC-500/505 A/D converters 200 nSec Maximum acquisition time • 0.01% accuracy • 100 nSec Maximum sample-hold settling time 74 dB Feedthrough attenuation ±50 pSec Aperture uncertainty Operable at different gain settings MECHANICAL DIMENSIONS INCHES (MM) GENERAL DESCRIPTION DATEL's SHM-45 is a high-speed, high accuracy samplehold designed for precision, high-speed analog signal processing applications. Manufactured with modern, high quality hybrid technology, the SHM-45 features excellent dynamic speCifications including a maximum acquisition time of only 200 nSec for a 10V step to 0.01 %. Sample-tohold settling time to 0.01 % accuracy is 100 nSec maximum with an aperture uncertainty of ±50 pSec. Lo800 MAX-.J !(20,31 I ~I o 150 MIN 1381 I T ----,:-- 0 010 I 1\ I I_ 0.190 (',91 MAX f 0018 KOVAR 13, 112 The SHM-45 is a complete sample-hold circuit, containing a precision MOS hold capacitor and a MOSFET switching configuration which results in faster switching and better feedthrough attenuation. Additionally, an FET input amplifier design allows faster acquisition and settling times while maintaining a considerably lower droop rate. r I ---.J 1__ 0 100 115.21--1 1(2,51 0600 NOTE: PINS HAVE 0.025 INCH STANDOFF FROM CASE, ±O.Ql~ INPUT/OUTPUT CONNECTIONS >---~---;:;: OUTPUT ~ 1 2 3 • 5 6 7 __ -.-+-+---I~;j - 15V 8 9 10 11 12 FUNCTION FUNCTION PIN 13 INPUT A OUTPUT 14 RANGE NIC 15 GROUND NIC 16 NIC NIC 17 NIC NIC 16 NIC NIC 19 NIC NIC 20 NIC N/C +5VSUPPlY 21 GROUND 15VSUPPlY GROUND 22 23 GROUND NIC HOll) COMMAND 24 +15V SUPPLY SYSTEM GROUND For Immediate Assistance, Dial 1-800-233,2765 4-11 SHM·45 Footnotes ABSOLUTE MAXIMUM RATINGS 1. ± 15V Supply Voltage (Pins 24, 22). . .. +5V Supply Voltage (Pin 9). . .. . . . . .. Analog Input (Pin 13,14)1.. . . . . . . . . .. Digital Input (Pins 11, 12). . . . . . . . . . ... Output Current 2 . . . . . , . . . : . . . . . . . . . ± 18V -0.5V to + 7V ±18V -0.5V to +5.5V ±65 mA FUNCTIONAL SPECIFICATIONS Specified at +25 °C, gains of -1, ±15V, and +5V power supplies unless otherwise specified. ANALOG INPUTS (Pin 13, 14) MIN. TYP. MAX. UNITS Input Volt. Range 1 Input Impedance ±10 1 - V Kohm - +0.8 40 -1.6 V V - - ±10.25 +11.5 LOGIC INPUTS (TTL) Logic 1 Voltage Logic 0 Voltage Logic 1 Current Logic 0 Current - +2.0 - Input signal times gain.should not exceed the output voltage range. 2. The SHM-45 output is current limited at approximately ±65 mAo The device can withstand a sustained short to ground. However, shorts to either supply will cause permanent damage. 3. Sample-to-Hold offset error (Pedestal) is constant regardless of input/output level. 4. FS is defined as 10 Volts. TECHNICAL NOTES 1. All ground pins (10, 15, 21, 23) should be tied together and connected to system analog ground as close to the package as possible. It is recommended to use a ground plane under the device and solder all four ground pins directly to it. Care must be taken to insure that no ground potentials can exist between pin 10 and the other ground pins. IJA 2. V mA ohm pi Although the power supply pins (9, 22, 24) are internally bypassed to ground with 0.01 ~F ceramic capacitors, additional external 0.1 ~F to 1 ~F tantalum bypass capacitors may be required in critical applications. 3. A logiC 1 on the HOLD COMMAND input, pin 12 will put the device in the sample mode. In this mode, the device acts as an inverting unity gain amplifier and its output will track its input. A logic 0 on pin 12 will put the device in the hold mode, and the output will be held constant at the last input level present when the hold command was given. 4. The maximum capacitive load to avoid oscillation is typically 250 pF. Recommended resistive load is 500n, although values as low as 250n may be used. Acquisition and sample-to-hold settling times are relatively unaffected by resistive loads down to 250n and capacitive loads up to 50 pF. However, higher capacitances will affect both acquisition and settling time. 5. TAe RANGE pin of the SHM-45 is usable to select different output voltage ranges. The output voltage ranges are selectable by hardware programming the SHM-45 to operate at different gains. Table 1 shows the range selection details. mA ANALOG OUTPUTS (Pin 1) Output Volt. Range Output Current 2 Output Impedance Max. Capacitive Load - - ±40 0.1 250 - - -1.0 :to.05 :to.5 :to.005 ±1 ±1 :to.l is :to.Ol is ±5 VN % ppm/"C %FS mV mV - 16 300 - MHz V/I!S - 200 170 - 160 100 6 ±1 - 60 40 100 - 0.5 15 1.2 ·74 5 TRANSFER CHARACTERISTICS Gain Gain Error Gain Tempco Linearity Error 5 Initial Offset Voltage ·Offset Step (pedestal) 3 - - DYNAMIC CHARACTERISTICS Frequency Response Small Signal (-3 dB) Slew Rate Acquisition Time 4 10V step to 0.01% FS 10V step to 0.1% FS Aperture Delay Time Aperture Uncertainty (Jitter) Settling Time 10V to :to.Ol% FS 10V to :to.l% FS Droop Rate aIT = +25 "C aIT = +70 "C aIT=+125"C Feedthrough Rejection - - - is - - nS nS nS pS nS nS j.lV/I!S j.lV/I!S mV/1!S dB POWER SUPPLY REQUIREMENTS Supply Voltage Range, :±15V +5V Power Supply Rej. Ratio Current Drains, +15V -15V +5V Power Consumption PHYSICAUENVIRONMENTAL Operating Temperature Range SHM-45MC SHM-45MM/MM-QL Storage Temperature Range Thermal Resistance Junction-to-Case Case-to-Ambient Package Type Pins 4-12 - :ill is :to.5 +21 -22 +17 730 +25 -25 +25 875 % % mVN mA mA mW mW Table 1. Jumper Selections for VIN -5 to +5 -10to+10 oto-5 o to -10 -10to +10 Oto-10 VOUT Ranges VOUT Connect . Pins Operating Gain +10to -10 +10to -10 o to +10 Oto +10 +5 to -5 oto +5 13 to 14 -2 -1 -2 -1 -0.5 -0.5 13 to 14 1 to 14 1 to 14 ORDERING INFORMATION o to +70 "C (ambient) ·55 to +125 "C (ambient) -65 to +150 "C 0.015 "C/mW 0.035 "C/mW 24-pin ceramic Kovar (0.010 x 0.018) MODEL TEMP. RANGE SHM-45MC SHM-45MM SHM-45MM-QL Oto +70 °C -55 to + 125°C -55 to +125 °C For availability fo MIL-STD-883B versions, contact DATEL. DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-11941TEL (508) 339-30001TLX 174388/FAX (508) 339-6356 SHM-4860 High-Speed, 0.010/0 Hybrid Sample-Hold FEATURES 200 Nanoseconds maximum acquisition time • 0.01 % Accuracy • 100 Nanoseconds maximum sample-hold settling time • 74 dB Feedthrough attenuation • ±SO Picoseconds aperture uncertainty GENERAL DESCRIPTION DATEL's SHM-4860 is a high-speed, highly accurate sample-hold designed for precision, high-speed analog signal processing applications. Manufactured using modern, highquality hybrid technology, the SHM-4860 features excellent dynamic specifications including a maximum acquisition time of only 200 nanoseconds for a 10V step to 0.01%. Sample-to-hold settling time, to 0.01% accuracy, is 100 nanoseconds maximum with an aperture uncertainty of ±50 picoseconds. MECHANICAL DIMENSIONS INCHES (MM) 1- L I 0.150 MIN (3,8) . - 0.800 MAX. _I (20.3) ~ 0.010 I The SHM-4860 is a complete sample-hold circuit, containing a precision MOS hold capacitor and a MOSFET switching configuration which results in faster switching and better feedthrough attenuation. Additionally, an FET input amplifier design allows faster acquisition and settling times while maintaining a considerably lower droop rate. l( DOT ON TOP PIN 1 f 0.018 KOVAR ··, ···· · --.,·, 13, ,, , "2 REFERENCES IO-.'-90-(.i.4,S-)-MAX-. r 1ru.... BOTTOM L 1- - VIEW ,'200 1 . . ·· ...1 ··,, · 11 SPACES AT 0.100 EA (2.5) (33,3) 241 --0 0.500 (15.2) ---.I 1_o.100 -l 1(2.5) NOTE: PINS HAVE 0.025 INCH STANDOFF FROM CASE, ± 0.01" INPUT/OUTPUT CONNECTIONS lKO INPUT l:j\----'I,W\~-i---, >-------1J)1 OUTPUT PIN 1 2 3 4 5 6 7 HOLD COMMAND (Jjllr----i---..., HOLD COMMAND 1 "'~+-+----!22-15V 8 9 10 11 12 FUNCTION OUTPUT NfC N/C N/C N/C N/C NfC N/C +5V SUPPLY GROUND HOLD COMMAND HOLD COMMAND PIN 13 14 15 16 17 18 19 20 21 22 23 24 FUNCTION INPUT N/C GROUND N/C N/C NfC NfC N/C GROUND -15V SUPPLY GROUND + 15VSUPPLY SYSTEM GROUND For Immediate Assistance, Dial 1-800-233-2765 4-13 SHM·4860 FUNCTIONAL SPECIFICATIONS Typcal at 25°C, ±15V, and +5V supplies unless otherwise noted. ANALOG INPUT/OUTPUT MIN. TYP. MAX. Input/Output Voltage Range Input Impedance Output Current' Output Impedance Maximum Capacitive Load ±10.25 ±11.5 1 - - - 0.1 250 ±40 - UNITS V kQ mA kQ pF DIGITAL INPUT Input Logic Level Logic 1 Logic: 0 Loading Logic 1 Logic 0 +2.0 0 - 5.0 0.8 V V - - 40 -1.6 mA mA - - 1.0 ±a.05 ±a.005 ±a.5 ±a.l ±a.Ol ±5 - :12.5 ±a.5 :120 ±5 mV ppm/ 'C - ±3 ±15 ppm - ±4 - ppm - 160 100 90 75 200 170 nS nS nS nS - 60 40 180 6 ±50 300 16 0.5 15 1.2 75 100 - ±3 ±5 ±a.5 - % % mVIV - +21 ·22 +17 730 +25 -25 +25 875 mA mA mA mW TRANSFER CHARACTERISTICS Gain Gain Accuracy Gain Linearity Error3 Sample-Mode Offset Voltage Sample-to-Hold Offset Error (Pedestal)4 Gain Tempeo (Drift) Sample-Mode Offset Drift", FSR/oC Sample-to-Hold Offset (Pedestal) Driftl - VIV % % FS mV DYNAMIC CHARACTERISTICS Acquisition Time 10V to ±a.Ol% FS 10Vto±a.l% FS 10Vto±l% FS 1Vto±l% FS Sample-to-Hold, Settling Time 10V to ±a.Ol % FS 10Vto ±a.l% FS Sample-to-Hold Transient Aperture Delay Time Aperture Uncertainty (Jitter) Output Slew Rate Small Signal Bandwidth (-3 dB) Droop: +25 'C +70 'C +125'C Feedthrough - - 5 - nS nS mV pop nS pS j.lV/1lB MHz j.lV/1lB j.lV/1lB mV/1lB dB POWER REQUIREMENTS Voltage Range: ±15V +5V Power Supply Rejection Ratio Quiescent Current Drain +15V -15V +5V Power Consumption - ABSOLUTE MAXIMUM RATINGS ± 15V Supply Voltage (Pins 24, 22) .•..• + 5V Supply Voltage (Pin 9) .......... . Analog Input (Pin 13)1 .............. . Digitallnput (Pins 11, 12) •••••.......• Output Current' .•......••••.......• ±18V -O.5V to + 7V ±18V -O.5V to +5.5V +65 rnA TECHNICAL NOTES 1. All ground pins (10, IS, 21, 23) should be tied together and connected to system analog ground as close to the package as possible. It is recommended to use a ground plane under the device and solder all four ground pins directly to it. Care must be taken to insure that no ground potentials can exist between Pin 10 and the other ground pins. 2. Although the power supply pins (9, 22, 24) are internally bypassed to ground with 0.01 p.F ceramic capacitors, additional external 0.1 p.F to 1 p.F tantalum bypass capacitors may be required in critical applications. 3. A logic "0" on the HOLD COMMAND INPUT, (Pin 11) (or a logic "1" on the HOLD COMMAND INPUT, Pin 12) will put the device in the sample mode. In this mode, the device acts as an inverting unity gain amplifier and its output will track its input. A logic" 1" on Pin 11 (logic "0" on Pin 12) will put the device in the HOLD mode, and the output will be held constant at the last input level present when the hold command was given. If the HOLD COMMAND INPUT (Pin 11) is used to control the device, Pin 12 must be tied to digital ground. If HOLD COMMAND INPUT (Pin 12) is used to control the device, Pin 11 must be tied to +5V. 4. The maximum capacitive load to avoid oscillation is typically 250 pF. Recommended resistive load is 5000, although values as low as 2500 may be used. Acquisition and sample-to-hold settling times are relatively unaffected by resistive loads down to 2500 and capacitive loads up to 50 pF. However, higher capacitances will affect both acquisition and settling time. PHYSICAL/ENVIRONMENTAL Operating Temperature Ranges SHM-4860 MC SHM-4860 MMlMM-QL Storage Temperature Range Package Type Pins Oto+70'C -55 to +125 'C -65to+150'C 24 Pin Ceramic Kovar (0.010 x 0.018) Footnotes 1. Input signal should not exceed the supply voltage. 2. The SHM-4860's output is current limited at approximately ±65 mAo The device can withstand a sustained short to ground. However, shorts from the output to either supply will cause permanent damage. For normal operation the load current should not exceed ±40 mAo 3. Fulll Scale (FS) =10V. Full Scale Range (FSR) =20V. 4. Sample-Io-Hold offsel error (Pedestal) is constant regardless of input/output level. 4-14 ORDERING INFORMATION MODEL NO. OPERATING TEMP. RANGE SHM-4860MC SHM-4860MM SHM-4860MM-QL Oto+70°C -55 to + 125°C -55 to + 125 °C For availability of MIL-STD-883B versions, contact DATEL. DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194ffEL (508) 339-3000ffLX 174388/FAX (508) 339-6356 SHM-6 0.02%, 2.0 Microseconds Microelectronic Sample-hold i!in i 1!II!1J Eli 7 FEATURES • 0.02% Accuracy 2.0 Microseconds acquisition time 2 Nanoseconds aperture uncertainty 5 MHz Bandwidth, small signal • 25 mA Output current Gain-programmable from ±1 to ±10 GENERAL DESCRIPTION DATEL's SHM-6 is a high-speed, high accuracy sample· hold circuit manufactured with thin-film hybrid technology. This design offers the speed and performance of modular sample-holds with the compactness and integrity of advanced hybrid techniques. The unit's excellent highspeed characteristics include a guaranteed acquisition time of 700 nanoseconds to 0.1 % accuracy and 2.0 microseconds to 0.02% for a 10 volt change. MECHANICAL DIMENSIONS INCHES (MM) L - l . 1 0 1 MAX (28,0) 1- I ~ 0.190('.') MAX "rJ -'11 O.I50MI~(3,8)U__ 0.010 The SHM-6 is a complete sample-hold containing a precision MOS holding capacitor. The input amplifier is an open loop transductance amplifier which can be externally connected for closed loop gains from ±1 to ±10. In addition to its speed, accuracy and selectable gain, the SHM-6 has an output capability of 25 mAo These features allow this unit to offer an unusual degree of adaptability. '" .IT x 0.160 (4,1) KOVAR , 16 BOTTOM ATO.l00EA 1.712 - ·"1.1 L ____ r- 0.900 (22,81 _-.J_ 0.100 I (2,5) NOTE: PINS HAVE 0.025 INCH STANDOFF FROM CASE, to.01 ~ .'5V -15V -j I .5V INPUT/OUTPUT CONNECTIONS PIN 1 2 3 4 5 10 L--'1/VI,_2Kll--, ANALOG COMMON OFFSET ADJUST Non~lnvertlng A' Sample/Hold Configuration, Gain = +1 R3 1 ~ -IN ? AI 1 ~"N D---'\IVv---- +IN 11 OUTPUT ~~/T Non-Inverting Sample/Hold Configuration, Gain = 1 + R21R1 ~~fTPUT • • 7 • I. 11 FUNCTION • IN _IN NC OFFSET ADJUST NC OFFSET ADJ. (Wrpet) NC OFFSET ADJUST NC ANALOG COMMON OllTl'U 12 NC 13 NC I. C.H. (OPTIONAL) ,. NC IS SJH ADJ. (Wiper) PIN FUNCTION 17 SfH STEP ADJUST . IB 5/H STEP ADJUST. " NC 20 21 22 23 2. 25 26 27 28 2' 30 31 32 NC NC DIGITAL CONTROL NC .Vde NC POWER GROUND NC +15Vdc NC NC -15Vdc NC Inverting Sample/Hold Conllgurallon, Gain = -R2/Rl For Immediate Assistance, Dial 1-800-233-2765 4-15 SHM·6 TECHNICAL NOTES ABSOLUTE MAXIMUM RATINGS Positive Supply. . . .. . .. .. .. . . . .... Negative Supply. . . . . .. .. .. . . .. ... Logic Supply .........••••....•.•• Digitallnput Voltage. . . • • • . . . • . • . •• Analog Input Voltage .• • • • • . . . . . . .. Differentiallnput Voltalile • . • . • • . • • •• + 18V -18V + 7.0V + 5.5V ± Vs ± 30V FUNCTIONAL SPECIFICATIONS Typical at 25°C, ±15Vand +5V supplies unless otherwise noted. INPUT AMPLIFIER SPECIFICATIONS Offset Voltage. . • .. .. • .. . . . . . . . ... Offset Voltage Tempeo •.•.....•.•• Offset Current. ..•....••••.....•.• Offset Current vs. Temp •.•.•.....•. BiasCurrent ...•...•.•.•........• Input Resistance .••...•••.•......• Common Mode Voltage Range .....• Common Mode Rejection Ratio ...... Open Loop Gain ••••.•...••.....•• Gain Bandwidth Product ....••.•••• Power Supply Rejection Ratio ••.•••• ± 2 mV ± 100 p.V/oC 1 nA maximum Doubles every 10°C 10 nA maximum lOS 11 ± 10V minimum 74 dB minimum 1Q6V/V 5 MHz 0.004%/% Supply DIGITAL INPUT CHARACTERISTICS Digital Control Logic ............... DTL, TTL Input Logic Level, Sample Mode ..... OV to + 0.8V at - 3.2 mA Input Logic Level, Hold Mode •.•.... + 2.0V to + 5.0V at + 80p.A ANALOG OUTPUT CHARACTERISTICS Output Voltage Range . . • • • . . . . . . .. ± 10V minimum Output Current • • • • • . • . • • • • . . . . . .. ± 25 mA maximum Output Resistance ................ 0.1 11 maximum SAMPLE/HOLD CHARACTERISTICS (Noninverting unity gain) Acquisition Time, 10VSteptoO.l% .•.•.•.•....... 700 nsec. maximum Acquisition Time, 10V Step to 0.02% ..••.•.••••••• 1.5 p.Sec. typical 2 "sec. maximum Aperture Delay Time .••..•.•••••••• 20 nsec. Aperture Uncertainty Time •....•.•.. 2 nsec. Sample to Hold Error •••.....•.•..• Adjustable to Zero Hold Mode Voltage Droop .........• 10 "V/p.sec. maximum Hold Mode Feedthrough •.........•• 0.02% maximum Offset .....••..••..............• Adjustable to Zero Gain ...•..........•............• ± 1 to ± 10 Gain Error .......••..•..•..•....• 0.01 % maximum Nonlinearity, Your ±10V •••••.••• 0.02% maximum Full Power Bandwidth, Your ± 10V ..•••••.........•• 500 KHz Slew Rate .....•.•.•.•........... 40 Vli ..•.•• Sample Controllnputs3 ••.••••••••• ±2.5V dc ± 5V dc 50 ~A 10 kO 500 Differential Eel 10.000 Positive Pulse on Pin 3 and Negative Pulse on Pin 1 gives Hold Mode. OUTPUTS Output Voltage Range', minimum ... maximum .. Output CurrenI' • • • • • • . . . . • • • . • • .. Outputlmpedance4 • • • • • • • • • • • • • •• ±2.5V dc ±5V dc ± 30 mA 130 PERFORMANCE Linearity ± 2.SV input volt. range ... ± SV input volt. range .•... Gain ........................... Gain Tempco, maximum. . . . . . . • . .. Sample-to-Hold Offset Error, maximum ............•....•... Sample-Mode Offset Voltage, maximum •..••...•.•.•......•. Sample-to-Hold Offset Voltage Drift .. Sample-Mode Offset Voltage Drift .•• Hold Mode Feedthrough, maximum .• Hold Mode Droop •••••..••••...... 0.1 % 0.2% +0.995 ± 33 ppm/oe 40 mV ±20 mV 75 ~v/oe ± 250 ~v/oe -66 dB 100 ~V/microseconds ABSOLUTE MAXIMUM RATINGS Positive Supply .... .. .. .. .. .. .... Negative Supply.. .. . . .. . . .. .. . . .. Digitallnput Voltage ....•.•.•..... Analog Input Voltage. . . . . . • . . . • . .• + 18V dc - 18V dc ± 5V dc ± 5V dc TECHNICAL NOTES ·1. The. use of good high Jrequency circuit board layout techniques is required for rated performance. The power common, analog common, and input common pins are not connected internally and therefore must be connected externally as directly as possible thorugh a low inductance, low resistance path. The extensive use of a ground plane for all common connections is highly recommended. 2. Although they are internally bypassed with 0.033 IlF capacitors the supply pins should be externally bypassed with 0.1 IlF ceramic Chip capacitors mounted as close to the supply pins as possible. 3. The SHM-7 inputs and outputs are sensitive to unusual loading or long lines. The analog input must be nonreactive so that leads should be short and purely resistive. Also, the complementary ECl driver should be as close as possible to pins 1 and 3 to minimize lead lengths to these pins. 4. The maximum, differential, digital input voltage is ±5V. For example, if pin 3 is at a potential of -5V, pin 1 may not exceedOV. DYNAMIC CHARACTERISTICS Acquisition Time, 2V to 0.1 % ...... 2V to 1% ....... 4V to 0.1% ...... 4V to 10Al ....... 10VtoO.l%" ..... 10Vto 1%" • . • . . • Aperture Delay Time .•....•.•.•... Aperture Uncertainty Time, maximum ...•...•............. Hold Mode Settling Time .•.•......• Sample-Mode Bandwidth; -3 dB ....• Sampling Rate' .................. +15V 40 nanoseconds 25 nanoseconds 50 nanoseconds 35 nanoseconds 60 nanoseconds 45 nanoseconds 3 nanoseconds 0.1 "F TYPICAL CONNECTION +~ 19 10 20 40 17 picoseconds nanoseconds MHz MHz POWER REQUIREMENTS ~-+_.() OUTPUT Positive Supply, Pin 19 .....•.•.•.. + 15V dc ± 0.5V dc at 60 mA Negative Supply, Pin 9 ...••..•.... -15V dc ±0.5V dc at 60 mA PHYSICAUENVIRONMENTAL Operating Temperature Ranges SHM-7MC ••..........•........ ooe to + 70°C Storage Temperature Range .•...... -65°C to + 150°C Package Type .........•.•....... 24 Pin, hermetically sealed, ceramic. Pins ............................ 0.010 x 0.D18 Inch Kovar Eel 10,000 DtFF LINE DRIVER O.1I'F FOOTNOTES: 1. The SHM-7MC has a maximum inputloulpulvoltage range of ±5V. 2. Should be purely resistive. See technical note 3. -tSV 3. Inputlogic voltage levels are V" "0" = -l.SV to -l.4V, and V;o "1" = -0.7V to -1.0SV. 4. Specified for each output, both outputs may be tied together for decreased output impedance and increased output current. ORDERING INFORMATION S. For a ± 2V input. 6. 10V is a step from -SV to +SV dc. 4-18 MODEL NO. OPERATING TEMP. RANGE SHM-7MC o to +70 °C DATEl, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194fTEL (508) 339-3000fTLX 174388/FAX (508) 339-6356 SHM-91 Precision Dual Sample-and-Hold FEATURES • Contains two.precision sample-hold amplifiers • Designed for use with 12- or 14-bit A/D converters Fast acquisition time (2 !lSec to ± 0.002%) • No external components required • Wide temperature range (-55 to +125°C available) • 24-pin dual in-line package Multiplexed inputs and outputs for application versatility MECHANICAL DIMENSIONS INCHES (MMJ ~0800 MAX-------.J 1- (20,3) ..L I r 1 GENERAL DESCRIPTION 01SOMIN 13.81 --.---- f KOVAR 01' I The SHM-91 consists of two separate sample-hold amplifiers, _each independently controlled to allow flexibility when implementing a system design. Each half consists of a twochannel input multiplexer and a sample-hold amplifier. The output of each sample-hold is-available directly or through a multipelxed output. 1,-0.-'9-0(.L4.9-)-MA-X 0010)1 0018 1 DATEL's SHM-91 is a high performance/high resolution dual sample-hold amplifier. This hybrid device is designed for multi-channel analog signal processing applications with 12· to 14-bit accuracy requirements. Typical applications for this device would demand high speed and high resolution. The SHM-91 offers both of these features at a low cost. ~ 13. BOTTOM vIEW I 1__ 1 a 100 12.5) NOTE: PINS HAVE 0.025 INCH STANDOFF FROM CASE, ±O.Ol~ INPUT/OUTPUT CONNECTIONS ' - -......-+v BEN 'lB 2B BSAMPLE For Immediate Assistance, Dial 1-800'233-2765 PIN SIGNAL 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 AOUT GROUND lA 2A +15V de -15V de AEN AADDR A SAMPLE NO CONNECTION MUXOUT GROUND BOUT GROUND lB 2B +15Vde -15V de BEN BADDR B SAMPLE NO CONNECTION MUXOUT GROUND ORDERING INFORMATION MODEL TEMP. RANGE SHM-91 Me SHM-91 MM 0 to +70 °e -55 to +125 °e 4-19 SHM·91 TIH SWITCHING ABSOLUTE MAXIMUM RATINGS Positive Supply (Pins 5,17) . . . . .. Negative Supply (Pins 6, 18) . . . .. Digital Input Voltages Address, Sample (Pins 8, 9, 20, 21) ..................... Mux. Enable (Pins 7, 19) . . . . . .. Analog lnput Voltage.. . . . . . . . . .. -0.5V dc to +18V dc +0.5V dc to -18V dc -0.5V dc to + 7V dc -18V dc to + 18V dc ±15V dc FUNCTIONAL SPECIFICATIONS The following specifications apply over the full operating temperature range and power supply range unless otherwise specified. For test aspects, contact the factory. DESCRIPTION MIN. ANALOG INPUTS Input Voltage Range ..... Input Impedance ...... Input Capacitance' ..... .. Input Bias Current ..... LOGIC INPUTS (TTL/CMOS Logic 1 voltage . ....... .. Logic 0 voltage . ...... Logic 1 cu rrent ...... Logic 0 current .......... ANALOG OUTPUTS Direct Output (pins 1, 13) Output Voltage Range . Output Current ...... .. ' Output Impedance ...... Mux. Output (pins 11, 23) Output Voltage Range ... Output Current ... ...... Output Impedance. ... OFF Output Leakage .. OFF Output Capacitance. Output Switch Delay. PERFORMANCE Gain (1) . ..... ..... Gain Error (1) .... ....... Gain Tempco .......... Linearity Error (1) . . . . . . . . Linearity Tempco... ...... Initial Offset Voltage (2) '" Offset Tempco., Hold Mode Crosstalk, channel-tochannel. .... ... ...... Offset Tempco. Tracking (Avs. B) .... ..... ... .' Gain Tracking (A vs. B) .. .. Gain Tracking Tempco... .. ±10 1M - - 2.4 - - ±10 10 - TYPICAL MAX. - - - 30 1.5 - - 0.8 1 1 - 1 - 2 - UNITS V Ohm pi p.A V V p.A p.A V mA Ohm ±10 10 - - - 50 150 1 20 500 V mA Ohms p.A pi nS - - - - - - - +1 - 1 - ±0.02 % ppm/oC 10 0.003 %FSR ppm/oC ±1 mV ±1 50 /LV/OC - 20 -90 - - dB - ±10 ±20 ±50 ±0.5 /LV/OC ppm ppm/OC - - PHYSICAL/ENVIRONMENTAL Thermal Resistance Junction-to-Case Case-to-Ambient Operating Temp. Range SHM-91MC SHM-91MM Storage Temperature Range Package Type 4-20 - 0.Q15 0.035 - °C/mW °C/mW o to +70 °C (ambient) -55 to +125 °C (ambient) -55 to +125 °C 24-pin hermetically sealed ceramic DIP Aperture Delay Time Aperture Uncertainty (Jitter) Offset Step (2) Settling Time to ±2 mV HOLD MODE DYNAMICS MIN. TYP. - 15 300 - - Droop Rate: +25°C +85°C +125°C -90 Feedthrough Rejection HOLD·;ro-TRACK DYNAMICS, - - - Acquisition Time 1OV Step to ±O.2 mV 10V Step to ±1 mV - MAX. 1,000 ±1 600 UNITS nS pS mV nS 5 10 100 I'V/I'S I'ViI'S I'V/I'S dB - 2 1.5 I'S I'S ±15 ±15.5 - 30 30 900 - POWER SUPPLY REQUIREMENTS Supply Voltage Range ±V Power Supply Rej. Ratio Current Drains: ± 15V dc -15V Power Dissipation ±14.5 -60 - - - - - 700 - - 1 45 - Vdc dB mA mA mW TRACK MODE DYNAMICS Frequency Response Small Signal (-3dB) ..... Slew Rate ... ........... Mhz V//LS 1. Specified at +25 °C. 2. Tested at ±25 °C with input source impedance of 50 ohms. TECHNICAL NOTES 1. All ground pirrs (2, 12, 14,24) should be tied together and connected to system analog ground'as close to. the pack'" age as possible. It is recommended to use a ground plane under the device and solder all four ground pins directly to it. Tne,power supply pins (5, 6, 17, 18) should be bypassed to analog ground with .01 ,.u= ceramic capacitors locatea as close to tha pins as possible. In certain critical applications, additional bypass precautions using 0.1 or 1.0 I'F tantalum capacitors are suggested. 2. A logic "I" on the sample pins (9, 21).will put this device in the sample l']1ode.ln this mode, the device acts as an unity gain amplifier and its output will track its input. A logic "0" on the sample pins (9, 21) will put the device in the hold mode, and the ;)utput will be held constant at the last input level present before- the hold command was given. 3. Care should be taken when using tbe mu!!!2lexeroutput pins (11,23) that the A EN (pin 7) and the B'EN.(pin 19) are not active (logic 0) at the same time. This condition could possibly damage the device. 4. The output of the SHM-91 should drive a high impedance receiver to minimize voltage divider losses. The receiver input impedance should be lOOK ohms or greater when using the direct outputs from the amplifiers (pins 1 and 13). The receiver input impedance should be 2.5 M ohms or greater when using the multiplexer outputs (pins 11 and 23). 5. The SHM-91 should not be left in the hold mode for long peri· ods of time. It should be left in the sample mode when long or indeterminate peFiods of time are involved. If left in the hold mode for several seconds, the output will continue to "droop" toward the power supply voltage. Eventually the output amplifier will saturate. The unit will require longer than the specified acquistion time to acquire a signal when the output amplifiers are saturated. 6. A Logic "I" on the A or B ADDR (Address) pins (8 and 20) will select channel 1A or 1 B on the respective input mux. A Logic "0" will select 2A or 2B. DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194ITEL (508) 339-3000ITLX 174388/FAX (508) 339-6356 SHM-945 High-Speed Hybrid Precision Sample-hold FEATURES • 500 nSec Maximum acquisition time to 0.00076% Differential input 0.0004% Linearity • 16-Bit Performance over military temperature range • Small 24-DDIP package Operates at different gain settings MECHANICAL DIMENSIONS INCHES (mm) GENERAL DESCRIPTION 0.800 MAX (20,3) DATEL's SHM-945 is a precision, high-speed sample-andhold featuring a maximum acquisition time of 500 nanoseconds to 0.00076% accuracy. Differential inputs are provided to reject common-mode signals found in applications requiring 16-bit accuracy. A range pin allows gain selections of -0.5, -1, and -2. I· ·1 ~ L I I 0.010 x 0.018 KOVAR Pins The SHM-945 contains an internal hold capacitor with internal compensation networks for pedestal error, feedthrough and dielectric absorption. 12 13: , , BOTTOM', VIEW , , , , TECHNICAL NOTES 1. Bypass the ±15V and +5V supplies with a 1 ~F, 25V tantalum electrolytic capacitor in parallel with a 0.01 ceramic capacitor, mounted as close to the pin as possible. 1 2. Tie ali ground pins together at a single ground point beneath the device and use a short, low impedance run to the ground of the analog power supplies. The ground paint should be a solid ground plane under the sample/hold and data converter. 24, t 0.190 MAX (4,9) -l----f 11 SPACES AtO.l00 (2,5) + t 0.150 MIN. (3,8) t 1.310 MAX. (33,3) I .0.600.1 (15,2) NOTE: Pins have 0.025 Inch ±0.01 stand-off from case. 3. Differential amplifier - high·resolution applications frequently require the ability to sense ground at a distant signal source. To avoid errors due to different ground potential, use the SHM-945's analog input low (pin 10) to sense the ground at the signal source. In noisy applications, using shielded twisted pair wire, with one end of the shield tied to ground at the sample/hold, is recommended. Analog Input Low and Range Return (when used) must be S; tOO mV maximum with respect to Analog Ground. 2K PIN 1 2 3 4 5 6 2K RANGE 14 7 2K ANALOG 13 INPUT HIGH 1 ANALOG OUTPUT ~ RANGE RETURN. 15 21 ANALOG GROUND ANALOG 10 INPUT LOW s/H 12 s/H 11 2-6,16-20 NO CONNECTION 7,23 POWER GND 24 +15V For Immediate Assistance, Dial 1-800-233-2765 22 -15V +5V DIGITAL GROUND 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 FUNCTION ANALOG OUTPUT NO CONNECTION NO CONNECTION NO CONNECTION NO CONNECTION NO CONNECTION POWER GROUND DIGITAL GROUND +5V ANALOG INPUT LOW SAMPLE/HOLD SAMPLE/HOLD ANALOG INPUT HIGH RANGE RANGE RETURN NO CONNECTION NO CONNECTION NO CONNECTION NO CONNECTION NO CONNECTION ANALOG GROUND -15V SUPPLY POWER GROUND +15V SUPPLY 4-21 [@~[L. SHM·945 ABSOLUTE MAXIMUM RATINGS PARAMETERS +15V Supply (pin 24) -15V Supply (pin 22) +5V Supply (pin 9) Digitallnpuls (pins 11,12) Analog Inputs (pin 13) Lead Temperalure (10 sec.) Short circuit to ground PERFORMANCE CONT. LIMITS UNITS -0.5 to +18 +0.510 -18 -0.5 to +7 -0.510 +7 -VSto+VS 300 max. 50 Vdc Vdc Vdc Vdc Vdc °C mA FUNCTIONAL SPECIFICATIONS Apply over the operating temperature range and over the operating power supply range unless otherwise specified. Gain = -1. INPUTS MIN TYP MAX Voltage Renges Common Mode Voltage Renge Common Mode Reject. Ratio Digilallnput Logic 1 Levels Logic 0 Levels Logic 1 Loading Logic 0 Loading ±10 ±100 86 ±10.5 - 2.0 - - - - 0.8 ±1 ±1 ±10 30 +10.5 35 - UNITS Vdc mV dB V dc Vdc ~ ~ OUTPUTS Voltage Renges Oulput Current Stable Capacitive Load Output Impedance - - 0.05 - 50 0.25 V rnA pF Ohms PERFORMANCE Nonlinearity: DC ±10V +25'C -5510 +125 'C Sample Mode Offset Error +25 'C 010 +70 'C -55to+125'C Sample Mode Offset Tempco SIH Offset (Pedestal) Error +25 'C 01O+70'C -5510 +125 'C Pedestal Tempco Pedestal Nonlinearity Gain Gain Error 25'C Oto +70 'C -55 to +125 'C Gain Tempeo Harmonic Dlslortion (below FS) CD Acq. Time, :to.OO3 %FS 10V Step +25 'C 010 +70 'C -55 to +125 'C Acq. Time, :to.OO3 %FS 20V Slep +25 'C Oto +70 'C -55 10 +125 'C Acq. Time, :to.DOO76 %FS 10V Stel +25'C 01O+70'C -5510 +125 'C Acq. Time, ±D.DOO76 %FS 20V SIB! +25'C 010 +70 'C -55to+125'C 4-22 - - - 0.5 - - - - - - ±2 - - 0.0004 %FS 0.00076 %FS 2 2.5 3 10 mV mV mV -1 - mV mV mV ppm/ 'C %FS VN 3 - ±D.02 ±D.035 ±D.05 5 %FS %FS %FS ppm! 'C dB -- 275 - - 350 350 425 nSec. nSec. nSec. - 375 400 450 500 nSec. nSec. nSec. 400 500 550 600 nSec. nSec. nSec. 650 700 750 nSec. nSec. nSec. -96 - - - - - 550 - - TYP MAX UNITS 10 13 15 30 nSec. nSec. pSec. pSec. V/llSec. MHz MHz 130 150 150 175 nSec. nSec. nSec. 200 250 250 300 nSec. nSec. nSec. dB 1 50 500 80 ~V/1lS ~V/1lS ~V/1lS 10 120 1.6 12 150 1.9 16 92 100 0.5 250 60 ~V RMS POWER SUPPLY REQUIREMENTS Range, +15V ·15V +5V Currenl, +15V ·15V +5V Power Dissipation Power Supply Rejeclion +14.25 ·14.25 +4.75 88 +15.0 ·15.0 +5.0 +10 ·10 +0.5 305 110 +15.75 ·15.75 +5.25 +12 ·12 +1.5 385 Vdc Vdc Vdc rnA rnA rnA mW dB ENVIRONMENTAL Operaling Temp. Range -MC -MM Storage Temp. Renge Package Type Weighl 0 -55 -65 +70 +125 +150 14-pin Hermetic DIP 0.28 Oz. (8 grams) max. 'C 'C 'C CD (DC 10 1 MHz, 10V pk-pk) . ~V/'C ±5 ±7.5 ±10 5 0.00076 ±5 ±7 2 MIN Aperture Delay, +25 'C ·5510 +125 'C Aperture Uncertainty, +25 'C ·55 to +125 'C Slew Rate Full Power BW (:l:fS) Small Signal BW (·3 dB) Hold Mode Settling, :to.OO3 %FS +25 'C Ot0+70'C ·55 to +125 'C Hold Mode Settling, :to.OO076 %FS +25 'C Oto +70 'C ·55 to +125 'C Feedthrough Rejection 10V Step Droop Rate, +25 'C Oto+70'C ·55 to +125 'C Output Noise, Hold Mode 4. For a gain of -{l.S, connect pin 14 (RANGE) 10 pin 1 (ANALOG OUTPUT) and lie pin 15 (RANGE RETURN) 10 ground. 5. For a gain of -2, connect pin 14to pin 13 (ANALOG INPUT) and tie pin 15 10 ground. 6. When using Sample/Hold (pin 11) connect pin 12 to Digital Ground. If using the Sample/AOJa polarity (pin 12) tie pin 11 to +5V. 7. The offset, pedestal, and gain errors of the SHM-945 are laser trimmed at DATEL and no external compensation capabilities have been provided. This prevents inlroducing noise through the offset adjust terminals of the S/H amplifier and guarantees excellent gain linearity, offset drift, and pedestal performance. ORDERING INFORMATION MODEL NUMBER TEMP. RANGE SEAL SHM·945MC SHM·945MM Oto+70°C -55 to +125 °C Hermetic Hermetic For availibility of MIL-STD-883 devices, contact DATEL. DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048·1194fTEL (508) 339-3000fTLX 174388/FAX (508) 339-6356 SHM-HU Ultra-Fast, 0.1 % Micro-Electronic Sample-hold FEATURES 25 Nanoseconds acquisition time • 50 MHz Bandwidth 10 Picoseconds aperture uncertainty • Up to 8-bit accuracy • ±2.5V Input range GENERAL DESCRIPTION DATEl's SHM-HU is an ultra high-speed sample-hold capable of video speed signal processing. The SHM-HU acquires a full-scale 5V input change in just 25 nanoseconds and features a 10 picoseconds aperture uncertainty time. Bandwidth is 50 MHz and the slew rate is 200 VImicroseconds. MECHANICAL DIMENSIONS INCHES (MM) Lo.fIJO MAX-.--J (20,3J ---I 1~I Through the use of thin-film hybrid construction, this ultra high-speed circuit is contained in a miniature 24-pin ceramic package. A 53 picofarad MaS hold capacitor is incorporated inside the package and provision is made for externally added capacitance when necessary. The sample-hold requires four external resistors and an lH0033 fast buffer amplifier for completion. The circuit is zeroed by adjustment of the lH0033 amplifier. o 150MIN 1381 1 --,:---- T 0010 I K 1--~-,~l(4-.•-)- 0018 KOVAR 112 13. tt SPACES Ala 100 I BOTTOM VIEW Other features of this unit include a ±2.5V input/output voltage range and a fixed gain of 0.0955. The sampling switch is controlled by a complementary series 10,000 ECl input. An ECl differential line driver can be conveniently used for the sample control inputs. I . lEA /2,51 1.31£~AX I -O~ ~OT ON TOP " 241 OHIO REFERENCES ' - - - - - - ' PIN 1 I~O.l00 ,12.51 Power requirements are ±15V dc at 60 mA and ±5V dc at 70 mAo There are three basic models covering two operating temperature ranges, 0 to +70°C, and -55 to +100°C. +BIAS 1 + BIAS 2 NOTE: PINS HAVE 0.025 INCH STANDOfF FROM CASE, :t: 0.01 N INPUT/OUTPUT CONNECTIONS ... r.Vdl:: PIN 1 FUNCTION SAMPLE CONTROL SAMPLE CONTROL 6 -BIAS 1 -BIAS 2 7 -5V POWER 9 10 GROUND 12 +5VPOWER 14 GROUND GROUND 15 16 GROUND OUTPUT 18 19 +5V POWER 20 +81AS2 22 INPUT 23 + BIAS 1 NOTE. AlL OTHER PINS ARE NO CONNECTION 3 I I GROUND _____ ..J -BIAS 1 -BIAS' _5Vdc For Immediate Assistance, Dial 1-800-233-2765 4-23 SHM·HU TECHNICAL NOTES ABSOl-UTE MAXQIIIUM RATINGS Power Supplies, Pins 9-19 . . • . .. Analog Input Voltage, Pin 22 . . .. Sample Inputs, Pins 1 & 3. . . • . •• Current, Pins 6, 7, 20, 23, •.•.... ± 6V ± 5V ± 5V Differential 50 rnA FUNCTIONAL SPECIF:ICATIONS Typical at 2S"C, ±1SV and ±SV supplies with external LH0033 Buffer Amplifier unleSli otherwise noted. 1. It is recommended that the ± 5V supplies of the SHM-HU be bypassed with 0.1 p.F ceramic capacitors as close as possible to pins 9 and 19. The ± 15V supplies to the lH0033 should be bypassed with the same value capacitors. 2. It is essential that the output lead from pin 18 to pin 5 of the lH0033 be kept as short and direct as possible. Also, the complementary ECl driver should be as close as possible to pins 1 and 3 to minimize lead lengths to these pins. 3. With model SHM-HUMC the LH0033C should be used, and with model SHM-HUMM, model LH0033 should be used. 4. An external hold capacitor may be added from pin 18 to pin INPUTS Input Volla8e Range, Min. ••.••. Input Bias urrent............. Maximum Source Impedance ..• Input Im~ance. . • • • • • . . . . • •• Sample ontrollnputs' .....••• ± 2.5V 25 pA 51 Ohms 10· Ohms Differential ECl 10,000 Positive Pulse on Pin 1 and Negative Pulse on Pin 3 gives Sample Mode 15. This capacitor should be an MOS or polystyrene type. Hold mode Droop and sample·to-hold offset error will decrease proportionately with the size of this capacitor and acquisition time will increase proportionately. CONNECTION DIAGRAM OUTPUT' +15V Output Voltage Range, Min •••..• ±2.5V Output Current .. . .. • .. • . • . . .• ± lOrnA Output Impedance ..••••...... 6 Ohms PERFORMANCE INPUT Accuracy .................... Gain ........................ Output Offset Voltagel , Sample Mode .•.....••..•... Output Offset Voltage Drift .••..• Sample 10 Hold Offset Error. . • .. Hold Mode Droop ...•..••.••.. Hold Mode Feedthrough ••.••... 22 -v----O:.~I- 0.1 % +0.995 L_ !: l _____ J ,. · 15 1 L.Hf-0"l -15V ." <0 OUTPUT '-1 1~~O;~10 ADJ. -15V -::- lH003. z~ ±100 mV max. ± 100 ",V/oC max. ± 100 mV max. 50 ",VIp-sec. 0.02% ,F , 12 t -lSV -5V DYNAMIC RESPONSE Acquisition Time, SV St~to 0.2% ••••...••.•• Bandwl , - 3 dB, Sample Mode .•••••••.•••••• Slew Rate ••••.•••••.•••••••• Aperture Delay TIme ••.••••.••• Aperture Uncertainty Time. • • . •• 25 nsec. 50 MHz 200V/",sec. 6 nsec. 10 psec. POWER REQUIREMENTS' Power Supply Voltage ••.••.••• ± 15V dc ±0.75V at 60 rnA ±5V dc ±0.25V at 70 mA PHYSICAL/ENVIRONMENTAL Operating Temperature Ranges SHM-HUMC .................. SHM-HUMM .................. Storage Temperature Range .... Package Type ..•••••••.••..•. Pins ........................ Weight. ..•••.••••••••••••••. 0 to + 70°C -55 to +100 o C -65 to +150°C 24 Pin Ceramic 0.010 x 0.018 inch Kovar 0.2 ounces (6 grams) FOOTNOTES: 1. Output is from LH0033 amplifier and is not short circuit proof. 2. Output offset voltage adjustable to zero by LH0033 offset adjustment. 3. ± 12V supplies can be used ij the 360 ohm resistors at the Bias 1 pins are changed to 240 ohms and the 240 ohm resistors at the Bias 2 pins are changed to 160 ohms. 4. The SHM·HU can be driven by TTL logic input by biasing SAt.iWI:E CONTROL input to + 1.2V and driving the SAMPLE CONTROL with a positive pulse for sampling mode. 4-24 ORDERING INFORMATION MODEL NO. OPERATING TEMP. RANGE SHM·HUMC SHM-HUMM SHM-HUMM-Ql Oto +70 °C -55 to +100 °C -55 to +100 °C DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194ffEL (508) 339-3000fflX 174388/FAX (508) 339-6356 SHM-49 High Speed, 0.01 % Hybrid Sample/Hold PRELIMINARY PRODUCT DA TA FEATURES • • • MECHANICAL DIMENSIONS 16 MHz small signal bandwidth Small 8 pin DIP or LCC package 200 nanoseconds maximum acquisition time to 0.01 % 100 nanoseconds maximum sample/hold settling time to 0.01% 72 dB feedthrough attenuation ±25 picoseconds aperture uncertainty 413 mW maximum power dissipation 0.250 OOS~ 1:=-1 D GENERAL DESCRIPTION -11- DATEL's SHM-49 is a high-speed, highly accurate sample/ hold designed for precision, high-speed analog signal processing applications. Manufactured using modern, highquality hybrid technology, the SHM-49 features excellent dynamic specifications including a maximum acquisition time of only 200 nanoseconds for a 1OV step to 0.01 %. Sample-tohold settling time, to 0.01% accuracy, is 100 nanoseconds maximum with an aperture uncertainty of ±25 picoseconds. PINOUT LCC +5V S/H ANALOG IN ANALOG RETURN -15V +15V POWER GROUND 4 (LCcT~:'SiOn) 19 18 -]Q.400SQ' 16 24 +0.010 SHM-49 ·0.005 12 0.020 to.OOS • 7 8 10 "'111"TT11'TTIITrIlTrIl""'1110.130 Max, t The SHM-49 is a complete sample/hold circuit, containing a precision MOS hold capacitor and a MOSFET switching configuration which results in faster switching and better feedthrough attenuation. Additionally a FET input amplifier design allows faster acquisition and settling times while maintaining a considerably lower droop rate. DIP ±O.OD5 0.390, to.OOS I .. .. I 1 0.13°1- Max. c:J 1:: CIJ:s 0.047, iO.002 1 2 3 4 5 7 8 ~ 7 ~~.+ 10 12 16 19 24 0.100 -15V +15V +5V 1.5K ANALOG o-3-+----J\.JV'.Ir--+----1 INPUT >-~___+6-o ANALOG OUTPUT S/H 2 CONTROL~-r----~ '---------' 8 POWER GROUND For Immediate Assistance, Dial 1-800-233-2765 4 ANALOG RETURN 4-25 SHM·49 .1 PHYSICAUENVIRONMENTAL ABSOLUTE MAXIMUM RATINGS Operating Temperature Range SHM-49MC/LC SHM·49MMlLM Storage Temperature Range Package Type;DIP LCC ±18V -0.5Vto +7V ±18V -0.5V to +5.5V ±65mA ±15V Supply Voltage +5V Supply Voltage Analog Input Digital Input Output Current oto +70 "C -55 to +125 "C -65 to+150 "C 8 pin ceramic 24 pin ceramic Footnotes FUNCTIONAL SPECIFICATIONS Apply ever temperature range and at ±15V dc and +5V dc unless otherwise specified:' ANALOG INPUT/OUTPUT MIN. TYP. Input/Output Voltage Range Input Impedance Output Current Output Impedance Capacitive Load ±10 ±11.5 2 - - MAX. UNITS - KQ ±40 mA 0,1 250 - - +5,0 +0.8 V Q pF DIGITAL INPUT Input Logic Level Logic 1 Logic 0 Loading 1 +2,0 0 - 1 - V V TIL TRANSFER CHARACTERISTICS Gain Gain Accuracy Gain Linearity Error 2 sample-Mode Ollset Voltage Sample-to·Hold Offset Error (Pedestal) 3 Gain Tempco (Drift) - -1.0 ±1 ±D,005 ±D.5 ±D,01 ±5 - ±2.5 ±D.5 ±25 ±15 Sample-Mode Offset Drift 2 - ±'l ±15 sample-to-Hold Offset (Pedestal) Drift - ±5 - ppmo! FSR/"C - 160 100 90 75 200 150 nS nS nS nS VN % %FS mV I. One TTL load is defined as sinking 40 IlA with a logic I input and· sourcing 1.6mA with a logic 0 input 2. Full Scale (FS) = 10V. Full Scale Range (FSR) = 20V. 3. Sample-la-Hold offset error (Pedestal) is constant regardless of inpuVoulput level. TECHNICAL NOTES 1. All ground pins should be tied together and connected to system analog ground as close to the package as possible. It is recommended to use a ground plane under the device and solder ground pins directly to it Care must be taken to insure that no ground potentials can exist between ground pins, 2. External 0.1 ~F to 1 ~F tantalum bypass capacitors are required in critical ap- plications. 3. A logic 1 on SIH puts the unit in the track mode. A logic 0 puts the unit in hold mode. 4. The maximum capacitive load to avoid oscillation is typically 250 pF, Recommended resistive load is 500n, although values as low as 250n may be used, Acquisition and sample-to-hold settling times are relatively unaffected by resistive loads down to 2500 and capacitive loads up to 50 pF. However, capacitances will affect both acquisition and settling time, mV ppmo! FSR/"C ppmo! FSR/"C (GAIN ADJUST) Al TO SHM·49, PIN 3 DYNAMIC CHARACTERISTICS Acquisition Time; 10V to ±D.Ol% FS (±1 mY) 10V to±D.l% FS (±10 mY) 10V to ±1% FS (±100 mY) lVto±l% FS (±100mV) Sample-to·Hold, Settling Time 10V to ±D.Ol% FS (±1 mY) 10V to ±D,I% FS (±10 mY) sample-ta-Hold Transient Aperture Delay Time Aperture Uncertainty (Jitter) Output Slew Rate Small Signal Bandwidth (-3 dB) Droop; +25 "C +70"C +125 "C Feedthrough - 200 - 60 40 100 10 <±25 300 16 0.5 15 1.2 72 - 100 - - 10 - - nS nS mVp-p nS pS V/flS MHz IlV/flS IlV/flS mVlflS dB 5.11K HIGH·SPEED, FAST SETTLING AMPLIFIER 3M SCKn -15V~+15V A2 (OFFSET ADJUST) Offset and Gain Adjustments NOTE: with a precision source, adjust R1 and R2 so that the output of the SHM-49 in the hold. mode matches the source output. POWER REQUIREMENTS Voltage Range, ±15V +5V Power Supply Rejection Ratio Quiescent Current Drain, +15V -15V +5V Power Consumption - - ±'l ±5 ±D.S +12 -12 +1 365 - +13,5 -13.5 +1.5 413 % % mVN mA mA mA mW ORDERING INFORMATION MODEL NO. OPERATING TEMP. RANGE SHM-49MC SHM-49LC SHM-49MM SHM-49LM Oto +70 °C Oto+70°C -55 to +125 °C -55 to +125 °C For availability of High Reliability versions of the SHM-49, contact DATEL. 4-26 DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194fTEL (508) 339-3000fTLX 174388/FAX (508) 339·6356 MSH-840 - Quad Simultaneous Sample Hold ADVANCED PRODUCT DATA mllilMIli.ill lit !i.fi FEATURES • • • • • • • • 4 Simultaneous sample holds Internal 4-channel multiplexer 750 nSec. Acquisition time, 10V step to 0.01 % 2 Channels with optional X10 gain Control logic for interfacing to AID's Low power - 1.5 Watts Small 32-pin TDIP -55°C to +125 °C Versions GENERAL DESCRIPTION' The MSH-840 is a quad simultaneous sample-hold featuring an acquisition time of 750 nSec. Control logic is provided for strobing the channels simultaneously and for interfacing to AID's. A 4-channel multiplexer allows individual S/H outputs to be digitized. PIN FUNCTION PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 DIGCOM +5V SSH11N OFSADJ1 SSH10UT SSH21N OFSADJ2 SSH20UT SSH31N OFSADJ3 GX103 SSH30UT SSH41N OFSADJ4 G X104 SSH40UT 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 FUNCTION +15V PWRCOM -15V MUXOUT MUX IN4 MUX IN3 MUX IN2 MUXIN1 ANACOM CA1 CAO START CONVERT CONY IN S/H IN EOC RST The MSH-840 requires +/-15V and +5V power supplies and dissipates just 1.5 Watts. Packaged in a small 32-pin TDIP, both commercial 0 to +70 °C and military -55 to +125 °C operating temperature range models are offered. • liiIli --jJIiIlij I.~t II! SSH1 OUT SSH2 OUT SSH3 OUT SSH4 OUT 12 16 _RIliliiil&_ MUXINl MUX IN2 MUXIN3 MUX IN4 24 23 22 21 OFSADJ1 SSH11N OFSADJ2 7 SSH21N OFSADJ3 10 20 MUXOUT SSH31N GX103 11 OFSADJ4 14 SSH41N 13 17 +15V GX104 15 19 ·15V 25 ANACOM 18 PWRCOM 2 +5V 1 DIGCOM 32 31 30 RST EOC S/HIN For Immediate Assistance, Dial 1-800-233-2765 29 28 CONVIN STCONV 27 26 CAO CAl 4-27 Contact DATEL for up-to-date information on products covered by "Advanced" and "Preliminary" product data sheets. Dial 1-800-233-2765 for Applications Assistance 4-28 DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-11941TEL (508) 339-30001TLX 174388/FAX (508) 339-6356 HYBRID DATA ACQUISITION SYSTEMS Model Resolution Throughput Linearity (Bits) (KHz) Error (Max) Power (Watts Max) Case Page 62-Pin 16SE ._--_._-------_._-_._ 5-1 Channels HDAS-16 12 50 HDAS-8 12 HDAS-7S 12 ±314 LSB 50 . _ - - - - _.. _-- - - 75 ±314 LSB HDAS-76 12 75 HDAS-S34 12 250 HDA.S-S38 12 250 ±314 LSB 3.0 SSE HDAS-S24 12 400 ±314 LSB 3.0 4 DE 5-11 40-PIN DIP ------5-7 40-Pin DIP ±314 LSB 1.75 ------1.75 ...... _------ 8 DE 62-Pin 5-1 0.7 SSE 40-Pin DIP 5-15 ±314 LSB 0.7 4DE ±3/4 LSB 3.0 4DE 40-Pin DIP 5-15 .-----5-11 40-Pin DIP HDAS-S28 12 400 ±314 LSB 3.0 SSE 40-Pin DIP 5-7 Preliminary HDAS-9S0 16 100 ±1/2 LSB@ 14 BITS 1.4 8SE 40-Pin DIP 5-19 Preliminary HDAS-9S1 16 100 ±1/2 LSB@ 14 BITS 1.4 4DE 40-Pin DIP 5-19 For Immediate Assistance, Dial 1-800-233-2765 5-i Contact DATEL for your Data Acquisition component needs. Dial 1-800-233-2765 for Applications Assistance 5-ii DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194fTEL (508) 339-3000fTLX 174388/FAX (508) 339-6356 HDAS-16, HDAS-8 12-Bit Microelectronic Data Acquisition Systems FEATURES • Miniature 63-pin hermetic package 12-8it resolution, 50 KHz Full-scale gain range of 50 mV to 10V • Three-state outputs • 16 Channels single-ended or 8 channels differential Auto-sequencing channel addressing • MIL-STD-883 versions • No missing codes MECHANICAL DIMENSIONS - INCHES (MM) 1------~2.~.~"--------i GENERAL DESCRIPTION seatrng 0.035 plane Using thin-and thick-film hybrid technology. DATEL offers complete low-cost data acquisition systems with superior performance and reliability. ;. . . . . . . . . . . . . . . . . . . . The HDAS-8 (with 8 differential input channels). and the HDAS-16 (with 16 single-ended input channels). are complete high performance 12-bit data acquisition systems in 62-pin packages. Each HDAS may expand to 32 singleended or 16 or more differential channels by adding external multiplexers. ~1 r - ' - - "- - - - - ' - - I " -I-:~:=: J 9 SPACES BOTTOM VIEW . 62. Internal channel address sequencing is automatic after each conversion. or the user may supply external channel addresses. I-(~:~~' DOT ON TOP REFERENCES PIN 1 ~i-"----------·------~ PIN SPACING IS a 100 INCHES '!(l005 NONCUMULATIVE ,(2.5 mm) A.T~i~:EA 1.400 (35.6).'" ~ MAXIMUM PIN OIMENSIONS ARE 0 012 xO 022 INCHES /03 >O.5MM) -~~ ~ CHOHI/CHO 4 °z i9 i ~a ~ a t--.,..., ~~~~ ~ ~I~~ 5 50 48 41 J!iI '-'><..>1...._ _ _ _ _ _-----,,--_ _ _ _ _---;-_ _ _ _ _--1---:-" A9 ... ;I Z2Q<) I A2 ~~~____.__~________ Ur----~;LI___________ Z2Q<) AI Z2Q<) ~~~------------:JfF-.40=-nSecC-~TY~~~7L-----~:IL---------- I I MODel CHO ADDRESSED I Cffiii : , I CH1 ADDRESSED SEQUENTIAL (EOOTteD TO Figure 2. I CH2 ADDRESSED : STAOii'"E) I CH12 ADDRESSED RANDOM ><><>< MAY ~~ANGE DON't CARE HDAS Timing Diagram INPUT VOLTAGE PROTECTION As shown in Figure 3, the multiplexer has reversed biased diodes which protect the input channels from being damaged by overvoltage signals. The HDAS input channels are protected up to 2f1II beyond the supplies and can be increased by adding series resistors (Ri) to each channel. The input resistor must limit the current flowing through the protection diodes to 10 mAo r-------:ffiv-----------l I I , I I R, : I I I Rl R2 l CHn INPUT The value of Ri for a specific voltage protection range (Vp) can be calculated by the following formula: Vp = (R signal + Ri + Ron) (10 mA) where RON 2K NOTE: Increased input series resistance will increase multiplexer settling time significantly. = RON Figure 3. := Rl + R2 = 2K Multiplexer Equivalent Circuit -ORDERING INFORMATION MODEL HDAS-16MC HDAS-16MM HDAS-16/883B HDAS-8MC HDAS-8MM HDAS-818838 OPERATING TEMP. RANGE OOCto + 700(; -55OC to + 1250C -55OC 10 + 1250C OOClo + 700C -55OC to +l25OC -55OC to + 1250C Receptacle for PC board mounting can be ordered through AMP Incorporated, #3-331272-4 (component lead spring socket) 62 required. 1883B Models are fully compliant to MIL-STD-883. 5-6 DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-11941TEL (508) 339-30001TLX 174388/FAX (508) 339-6356 HDAS-524,-528 12-Bit, 400 KHz Data Acquisition Systems FEATURES • 12-bit resolution, 400 KHz • 8 channels single-ended or 4 channels differential • • • • Miniature 40-pin DDiP Full scale gain range from 100 mV to 10V Three-state outputs No missing codes GENERAL DESCRIPTION The HDAS-524,-528 are complete data acquisition systems containing an internal multiplexer, instrumentation amplifier, sample-hold, analog-to-digital converter and three-state outputs. Packaged in a miniature 40-pin double-dip package, the HDAS-524/528 has a low power dissipation of 2.6 watts. The HDAS-524 provides 4 differential inputs and the HDAS528 provides 8 single-ended inputs. An internal instrumentation amplifier is characterized for gains of 1,2,4,8,10 and 100. The gain range is selectable through an external resistor. TECHNICAL NOTES 1. Rated performance requires using good high-frequency circuit board layout techniques. The analog and digital grounds are not connected internally. Avoid groundrelated problems by connecting the analog, signal and digital grounds to one point, the ground plane beneath the converter. Due to the inductance and resistance of the power supply return paths, return the analog and digital ground separately to the power supplies. This prevents contamination of the analog ground by noisy digital ground currents. 2. Double-level multiplexing allows expanding the multiplexer channel capacity of the HDAS-528 from 8 singleended channels to 128 single-ended channels or the HDAS-524 from 4 differential channels to 32 single-ended channels. SlH OUT GAIN GAIN HI LO 10 GAIN ADJ. 15 INPUT/OUTPUT CONNECTIONS OffSET BIPOLAR ADJ. 16 PIN 33 81T 1 (MSS) CHOICHOHI CH1ICHl HI 32 8112 31 BIT3 2x4;1 (524) CH2ICH2 HI CH3JCH3HI CH4ICHOLO CH5ICHI LO MUX CH6ICH2LO (528) 12·81T AID 8:1 CH7/CH3l0 SIGNAL 14 ONO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 IS 16 17 34 ENABlE 18 19 20 FUNcnON CHOlCH a HI CH lICH 1 HI CH21CH 2 HI CH3/CH 3 HI CH 7/CH 3 LO CH6JCH 2 LO CH 5/CH 1 LO CH4/CH 0 LO CaMP BIN RGAIN LO RGAIN HI SlHOUT +10V REF OUT SIGNALGNO GAINADJ OFFSET ADJUST BIPOLAR -15V ANALOGGND +15V PIN 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 FUNCTION STARTCNVRT CA2 CAl CAO .5V DIG1TALGND ENABLE BIT 1 (MSB) BIT 2 BIT3 BIT4 BIT 5 BIT6 BIT7 BIT 8 BIT9 B!T10 BIT11 BtT12 EOC " - - - - 1 9 caMP BIN 39 38 37 CA2 CAt CAO 19 35 ANA DIG GND GND 36 20 +5V +15V 18 ·15V 13 REF OUT For Immediate Assistance, Dial 1-800-233-2765 40 START CONVERT 21 EOC 5-7 HDAS-S24,-S28 ABSOLUTE MAXIMUM RATINGS PERFORMANCE PARAMETERS LIMITS +15V Supply (pin 20) -15V Supply (pin 18) +5V Supply (pin 36) Digital Inputs (pins 9, pins 34, 36-40) Analog Inputs (pins 1-8) Lead Temp. (10 Sec.) oto +18 UNITS Vdc Vdc Vdc Oto·18 -0.5 to +7.0 Vdc V -0.3 to +6.0 ±25 300 FUNCTIONAL SPECIFICATIONS Apply over the operating temperature range and at ±15V dc and +5V dc unless otherwise specified. ANALOG INPUTS MIN. TYP. Number of Inputs HDAS-524 HDAS-528 Input Voltage Ranges Gain = 1 Gain = 100 I.A. Galn Ranges Inputlmpedanc:e CHON,CHOFF Input Capacitance (-528) CH ON, CH OFF (-524) CH ON,CH OFF Input Bias Current Input Offset Current Input Offset Voltage Common Mode von. Range CMMR, G=I,@10Hz, Vcm=1V pop VoHage Noise (RMS) Gain=1 Gain=8 MUX Crosstalk @ 125 KHz MUX ON Resistance Bias Current Tempeo Offset Current Tempco Offset Voltage Tempco Input Gain Equation MAX. UNITS 4 differential inputs 8 sing!e-ended inputs - Ohms 25 12 200 50 ±10 - pF pF pA pA mV V -80 - dB - 200 50 1012 - - - - ±11 - -75 -72 - - - !LV !LV dB 450 Ohms 500 Doubles (max.) every to °C above 70°C Doubles (max.) every 10°C abcve 70°C (±30 ppm/ °C x gain) ±20 ppm/ °C (max.) Rg = 1~(gain -1)12K] - - DIGITAL INPUTS Logic Levels Logic 1 Logic 0 logie loading Logic 1 Logic 0 2.0 - - - 0.8 - Vdc Vdc - 5 -200 !LA !LA - Output Coding - - 0.4 - Vdc Vdc - - - -160 6.4 !LA rnA +9.9 +10.0 +10.1 ±35 1.5 Vdc ppm/°C rnA 2.4 - - ±5 - Enable to Data Val. Delay MUX Address Set-up Time Start Convert Pulse Width Data Valid Aller EOC Signal Goes Low Conversion Time, +25 °C Oto +70 °C -55 to +125°C Throughput Rates Gain= 1, (j) Gain =2, (j) Gain =4, (j) Gain =8, (j) Gain = 10, (j) Gain = 100, (j) - - - - UNITS - - - - ±3/4 ±3/4 ±t.5 Bits LSB LSB LSB - ±3/4. ±3/4 ±1 ±0.30 ±D.5 ±0.78 ±0.15 ±30 ±0.15 ±10 ±D.25 ±40 ±0.25 ±40 LSB LSB LSB %FSR %FSR %FSR %FSR ppm/°C %FSR ppm/ °C %FSR ppm/oC %FSR ppm/°C - ±0.13 ±0.15 ±0.25 ±0.074 ±15 ±0.074 ±5 ±D.l ±20 ±0.1 ±20 -65 -73 dB Over operating temperature range 400 50 - 100 - - - 400 325 275 225 175 40 - - 500 - 10 - nS nS nS 20 800 850 880 nS nS nS nS - KHz KHz KHz KHz KHz KHz - SJH PERFORMANCE Aequlstion Time Full Scale Step to 0.01% Full Scale Step to 0.1% Aperture Delay Aperture Uncertainty Slew Rate Hold Mode Settling Time, 10V to ±0.01 %FS 10V to ±D.l%FS Feedthrough Rejection Droop Rate, CD Straight binarylOffset binary Complementary binary Complementary offset binary Range.15V ·15V +5V Currenl+15V ·15V +5V Power Dissipation Power Supply Rejection -50 - 70 400 -20 ±100 90 900 750 0 ±150 nS nS nS nS V/IlS 200 150 nS nS dB IlV/IlS - - - 100 75 -80 - -88 0.1 100 +15.0 -15.0 +5.0 +78 -72 +75 2.6 +15.75 -15.75 +5.25 +90 ·82 +90 3.0 0.01% - +14.25 -14.25 +4.75 - - - Vdc Vdc Vdc rnA rnA rnA Watts %FSRI%V ENVIRONMENTAL Oper. Temp. Range, ·MC -MM Storage Temp. Range Package Type Weight Pins (j) 5-8 - MAX. POWER SUPPLY OUTPUTS Logie Levels Logic 1 Logic 0 Logic Loading Logic 1 Logic 0 Internal Reference VoHage, +25 °C Drill External Current 12 TYP. SIGNAL TIMING Oto+l0V,±10V Oto 100mV ,+100 mV 1,2,4,8, lu, 100 10" Resolution Integral Nonlinearity,25 °C Oto +70 °C -55 to +125 °C Differential Nonlinearity +25°C Oto+70°C -55 to +125°C F_S. Abe. Aecuracy +25 °C Oto+70°C -55to+I25°C Unipolar Zero Error,+25 °C Unipolar Zero Tempco Bipolar Zero Error, +25 °C Bipolar Zero Tempco Bipotar Offset Error,+25 °C Bipolar Offset Tempeo Gain Error, +25 °C Gain Tempeo Hannonie Distortion (. FS) (DC to 50 KHz,1 OV pk·pk) CD No Missing Codes MIN. 0 -55 - +70 °c +125 °C -65 +150 oc. 40-pin DIP 0.32 ox. (9 grams) max. 0.010 x 0.Q18 in. Kovar Specifications valid at 25°C and over the temperature ranges of oto +70 °C and -55 to +125 °C. DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194fTEL (508) 339-3000fTLX 174388/FAX (508) 339-6356 HDAS-S24,-S28 Hi TECHNICAL NOTES (CaNT.) 11 n Table 1. MUX Channel Addressing 3. Obtain straight binary/offset binary output coding by tying COMP BIN (pin 9) to +5V dc or leaving it open. The device has an internal pull·up resistor on this pin. To obtain comple· mentary binary or complementary offset binary output coding, tie the CaMP BIN pin to ground. The CaMP BIN signal is compatible to CMOSITTL logic levels for those users desiring logic control of this function. HDAS-S24 (2-6fT ADDRESS) HDAS-528 (3·BIT ADDRESS) 4. To enable the three·state outputs, connect e:JAB['E (pin 10) to a logic "a" (low). To disable, connect ENABLE (pin 10) to a logic "1" (high). Table 2. Input Range Parameters HDA5-524/528 OPERATION GAIN RGAINO Oto+l0V 1 OPEN 400 KHz Oto+5V 2 2K 4 665U 325 KHz 275 KHz 225 KHz 175 KHz 40 KHz INPUT RANGE The HDAS devices accept either 8 single'ended or 4 differential input signals. Tie unused channels to SIGNAL GROUND, pin 14. o to +2.5V 221 ±2.5V ±1.25V ±1.0V ±100mV Note 1. n 20.0 OPEN 1 ±10V ±5V The acquisition time is the amount of time the multiplexer, instrumentation amplifier and sample-hold require to settle within a specified range of ~racy; The acquisition time can be measured by how long EOC is low before the rising edge of the START CONVERT pulse for continuous operation. Higher gains require the use of the RGAIN resistor to increase the acquisition time. The gain is equal to 1 without an RGAIN resistor. Table 2 refers to the appropriate RGAIN resistors for various throughputs. 287U 10 100 Oto+1.0V Oto+100mV Channel selection is accomplished using the multiplexer address pins shown in Table 1. Obtain additional channels by connecting external multiplexers. The HDAS devices enter the hold mode and are ready for conversion upon the start convert going high. The con~ion is complete within a maximum of 800 nsec ( + 25°C). EOC returns low, the data is valid and sent to the three-state output buffers. The sample/hold is now ready to acquire new data. a o to +1.25V THROUGHPUT 2 2K 4 665U 287U 221 n 20U 8 10 100 400 KHz 325 KHz 275 KHz 225 KHz 175 KHz 40 KHz Rgain '" 10 ROAlNHI tC_RGAIN11 S/H OUT +10V REF o { 4.7~FI ~ 1 r1 RGAINLO 12 13 ~F19 HDAS-524/528 -15V 20K --100 nS Typ . .......-15V START CONVERT 20K +15V :>-o>--____.!!162,j OFFSET ADJUST 1 .850n8. 1 ______~~I~~________~~L_________ +15V 35n5 Max,' I OUTPUT DATA I 1.8~8 - ---------------.I-.~~r--E-na-b-I.-dd-a-la-~-.~ I I I CAl 10 nS N Valid 10 nS CAO Figure 2. Typical Connection Diagram CHO CHl CH2 Figure 1. HDAS-524/528 Timing Diagram NOTES: 1. 2. A START CONVERT pulse grea1er thall.15Q nS will slow the throughput. Retriggering START CONVERT before EOC goes low will not start a new conversion. 3. Times shown apply over the full operating temperature range. For Immediate Assistance, Dial 1-800-233-2765 NOTES: 1. For unipolar operation, connect pin 12 to pin 17. 2. For bipolar operation, connect pin 13 to pin 17. 3. Position RGAIN as close as possible to pins 10 and 11. Use RN55C, 1% resistors. 4. If gain and offset adjusts are not used connect pin 15 to ground and leave pin 16 open. 5-9 HDAS-S24,-S28 MECHANICAL DIMENSIONS CALIBRATION PROCEDURE INCHES (mm) 1. Connect the converter per Figure 2 and Tables 2 and 3 for the appropriate full-scale range (FSR). Apply a pulse of 100 nanoseconds (typical) to the START CONVERT input (pin 40) at a rate of 100 KHz. This rate is chosen to reduce flicker if LED's are useo on the outputs for calibration purposes. 0.810 Max. 1_ ~ I . 0.150(3,8)Min.= t -I (20,6) I- U, U I 1 2. Zero Adjustments 21 HDAS-S24 HDA5-S28 Apply a precision voltage reference source between the analog input and signal ground (pin 14). Adjust the output of the reference source per Table 3. For unipolar, adjust the zero trimming potentiometer so that the output code llickers equally between 0000 0000 0000 and 0000 0000 0001 with the COMP BIN (pin 9) tied high (straight binary) or between 1111 11111111 and111111111110withtheCOMPBIN(pin9) tied low (complementary binary). 1 2.2 Max. (53,8) BOTTOM VIEW 1__ For bipolar operation, adjust the potentiometer such that the code flickers equally between 1000 0000 0000 and 1000 0000 0001 with COMP BIN (pin 9) tied high (offset binary) or between 0111 1111 1111 and 0111 1111 1110 with COMP BIN (pin 9) tied low (complementary offset binary). 40 0.600 (15,2) --II -- Table 3. 0.190 (4,9) Max. T 0.010 X 0.018 KOVAR 20 20 Spaces al 0.1 00 (2,5) Intervals ~ 0.100 -- 3. Full-Scale Adjustment (2,5) Set the output of the voltage reference used in step 2 to the value shown in Table 3. Adjust the gain trimming potentiometer so that the output code llickers equally between 1111 1111 1110 and 1111 11111111 or 0000 0000 0001 and 0000 0000 0000 for complementary coding. Zero and Gain Adjust FSR a to +10Vdc ±10V Zero Adjust +1/2 LSB Gain Adjust +FS - 1 1/2 LSB +1.22 mV +2.44 mVdc +9.9963V +9.9927V dc 4. To confirm proper operation of the device, vary the precision reference voltage source to obtain the output coding listed in Table 4. Table 4. Output Coding STRAIGHT UNIPOLAR INPUT RANGE SCALE +FS -1 LSB 7/8 FS 3/4 FS 1/2 FS 1/4 FS 1/8 FS 1 LSB Oto+10Vdc +9.9976V +8.7500V +7.5000V +5.0000V 2.5000V 1.2500V o.o024V O.OOOOV a BIN CaMP BINARY OUTPUT CODING MSB LSB 111111111111 1110 0000 0000 1100 0000 0000 1000 0000 0000 0100 0000 0000 0010 0000 0000 0000 0000 0001 0000 0000 0000 OFF BINARY INPUT RANGE BIPOLAR +10Vdc +9.9951V +7.5000V +5.0000V O.OOOOV -5.0000V -7.5000V -9.9951V -10.000V SCALE +FS -1 LSB +3/4 FS +1/2 FS MSB LSB 0000 0000 0000 000111111111 001111111111 0111 1111 1111 1011 1111 1111 110111111111 111111111110 111111111111 CaMP OFF a -1/2 FS -3/4 FS -FS +1 LSB -FS BIN ORDERING INFORMATION MODEL NUMBER HDA5-S24MC HDA5-S24MM HDA5-S28MC HDA5-S28MM INPUT 4 D CHANNELS 4 D CHANNELS 8 sE CHANNELS 8 SE CHANNELS OPERATING TEMP. RANGE o to +70 °c -55 to +125 °C a to +70 °c -55 to +125 °C SEAL Hermetic Hermetic Hermetic Hermetic Receptacle for PC board mounting can be ordered through AMP Inc.,Part # 3-331272-8 (Component Lead Socket), 40 required. For availability of MIL-sTO-8838 _ns of the HDA5-524 & HDA5-528, contact DATEL. 5-10 DATEL, Inc, 11 Cabot Boulevard, Mansfield, MA 02048-1194fTEL (508) 339-3000fTLX 174388/FAX (508) 339-6356 HDAS-534,-538 12-Bit, 250 KHz Data Acquisition Systems v FEATURES • • • • • • 12-bit resolution, 250 KHz 8 channels single-ended or 4 channels differential Miniature 40-pin DDIP Full scale gain range from 100 mV to 10V Three-state outputs No missing codes GENERAL DESCRIPTION The HDAS-534/538 are complete data acquisition systems containing an internal multiplexer, instrumentation amplifier, sample-hold, analog-to-digital converter and three-state outputs. Packaged in a miniature 40-pin double-dip package, the HDAS-534/538 provides 250 KHz throughput with a low power dissipation of 2.6 Watts. MECHANICAL DIMENSIONS INCHES (mm) 0.B10 Max. 1_ ~ I 0.150(3.8)Min.= The HDAS-534 provides 4 differential inputs and the HDAS538 provides 8 single-ended inputs. An internal instrumentation amplifier is characterized for gains of 1,2.4,8,10 and 100. The gain range is selectable through an external resistor. t -1 TECHNICAL NOTES 1. Rated performance requires using good high-frequency circuit board layout techniques. The analog and digital grounds are not connected internally. Avoid ground-related problems by connecting the analog, signal and digital grounds to one pOint, the ground plane beneath the converter. Due to the inductance and resistance of the power supply return paths, return the analog and digital ground separately to the power supplies. 20 Spaces at 0.100 (2,5) Intervals -I r- U, ~ T U 0.190 (4,9) Max. 0.010 X 0.018 KOVAR 21 I 20 I I I I HDAS-534 I HDAS-538 I I BOnOM I VIEW I 1 2.2 Max. (53,8) i 1 I I I I I 1 2. Double-level multiplexing allows expanding the multiplexer channel capacity of the HDAS-538 from 8 single-ended channels to 128 single-ended channels or the HDAS-534 from 4 differential channels to 32 single-ended channels. 3 Obtain straight binary/offset binary output coding by tying COMP BIN (pin 9) to +5V dc or leaving it open. The device has an internal pull-up resistor on this pin. To obtain complementary binary or complementary offset binary output coding, (20.6) j 40 1..- (15,2) 0.600 --II -.. 0.100 - - (2,5) tie pin 9 to ground. Pin 9 signal is compatible to CMOSITTL logic levels for logic control of this function. 4. To enable the three-state outputs, connect ENABLE (pin 10) to a logic "0· (low). To disable, connect pin 10 to a logic "1" (high). INPUT/OUTPUT CONNECTIONS 81H OUT 12 GAIN GAIN HI LO 10 GAIN AOJ 15 OFFSET BIPOLAR ADJ. 17 16 PIN FUNCTION 33 BIT 1 (MSB) 32 BI12 CHOJCHOHI CHlfCHl HI 2x4:1 31 SIT3 (534) 30 81T4 29 BITS 28 B1T8 CH2ICH2HI CH3ICH3HI CH4JCHOLO MUX CH51CHl LO 8.1 (538) 27 BIT7 12·81T CH6ICH2LQ 26 BIT8 25 81T9 AJD 24 BIll0 CH71CH3LO 23 BIT11 22 BIT 12 (LSBJ SIGNAl 14 OND 34~ '------1 39 CA2 38 CAl 37 CAO 19 35 ANA DIG GND GND 36 20 +51/ +151/ 18 -151/ 13 REF OUT For Immediate Assistance, Dial 1-800-233-2765 40 START CONVERT 21 EOC 9COMP BIN t 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 CH O/CHO HI CH 1/CH 1 HI CH 2/CH2 HI CH 3/CH3HI CH 7/CH3 LO CH 6/CH2 LO CH 5/CH 1 LO CH 4/CH a LO COMP BIN AGAIN LO AGAIN HI S/HOUT +10V AEF OUT SIGNALGND GAINADJ OFFSET ADJUST BIPOlAA ·t5V ANALOGGND +t5V PIN FUNCTION 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 STAATCNVAT CA2 CAl CAO +5V DIGITALGND ENABLE BITl (MSB) BIT2 BIT 3 BIT 4 BIT5 BIT6 BIT7 BIT8 BIT 9 BITtO BIT 11 BIT t2 (LSB) EOC 5-11 HDAS-S34,-S38 ABSOLUTE MAXIMUM RATINGS PERFORMANCE LIMITS PARAMETERS +15V Supply (pin 20) -15V SIIPply (pin 18) +5V Supply (pin 36) Digital Inputs (pins 34, 37-40) Analog Inputs (pins 1"8) Lead Temp. (10 Sec.) UNITS Oto +18 Oto ·18 -0.5 to +7.0 Vdc Vdc Vdc -0.3 to +6.0 ±25 300 Vdc V °C FUNCTIONAL SPECIFICATIONS Apply over the operating temperature range and at ±t 5V dc and +5V dc unless otherwise specified. ANALOG INPUTS MIN. Number of Inputs HDAS-534 HDAS-538 Input Voltage Ranges Gain = 1 Gain = 100 I.A. Gain Ranges Input Impedance CHON, CH OFF Input Capacitance (534) CH ON, CH OFF (538) CH ON,CH OFF Input Bias Current Input Offset Current Input Offset Voltage Common Mode Volt. Range CMMR, G=1 ,@ 10 Hz, Vcm=1V p.p Voltage Noise (RMS) Gain=1 Gain = 8 MUX Crosstalk @ 125 KHz MUX ON Resistance Bias Current Tempco Offset Current Tempco Offset Voltage Tempeo Input Gain Equation TYP. MAX. UNITS 4 differential inputs 8 single-ended inputs 1,2,4,8,10,100 1011 1012 - Ohms - - 25 12 200 50 ±10 pF pF pA pA mV V - ±11 - -75 -80 - - - dB 200 ~V 50 ~V -72 dB 450 500 Ohms Doubles (max.) every 10 'C abcve 70 'C Doubles (max.) every 10 'C abcve 70 'C (±30 ppml 'C x gain) ±20 ppml 'C (max.) Rg = 1I1(gain ·1)/2K] DIGITAL INPUTS Logic Levels Logic 1 Logic 0 Logic Loading Logic 1 Logic 0 - 2.0 - - - - - - 0.8 Vdc V dc 5 -200 j.IA j.IA OUTPUTS Logic Levels Logic 1 Logic a Logic Loading Logic 1 Logic 0 Internal Reference Voltage, +25 "C Drift External Current Output Coding 5-12 - - - - +9.9 +10.0 ±5 2.4 - - - TYP. 12 - - - - - ±D.13 ±D.15 ±D.25 ±D.074 ±15 ±D.074 ±5 ±D.1 ±20 ±D.1 ±20 MAX, ±3/4 ±3/4 ±1.5 ±3/4 ±3/4 ±1 ±D.30 ±D.5 ±D.7S ±D.15 ±30 ±D.15 ±10 ±D.25 ±40 ±D.25 ±40 UNITS Bits LSB LSB LSB LSB LSB LSB %FSR %FSR %FSR %FSR ppm/"C %FSR ppm/"C %FSR ppm/"C %FSR ppm/"C -65 ·73 dB uver operating temperature range SIGNAL TIMING oto +10V, ±10V oto 100 mV, ±100 mV - Resolution Integral Nonlinearity,25 "C Oto +70 "C -55 to +125 'C Differential Nonlinearity, +25 "C 010 +70 "C -55 to +125 'C F.S. Abs. Aceuracy +25 "C oto +70 "C -55 to +125 "C Unipolar Zero Error,+25 "C Unipolar Zero Tempco Bipolar Zero Error, +25 "C Bipolar Zero Tempco Bipolar Offset Error,+25 "C Bipolar Offset Tempco Gain Error, +25 "C Gain Tempeo Harmonic Distortion (- FS) (DC to 50 KHz, 10V pk-pk)"(j) No Missing Codes MIN. 0.4 Vdc V dc -160 6.4 j.IA mA +10.1 ±35 1.5 Vdc ppm/"C mA Straight binarylOffset binary Complementary binary Complementary offset binary Enable to Data Val. Delay MUX Address Set-up Time Start Convert Pulse Width Data Valid Before EOCSignal Goes Low Conversion Time, +25 "C oto +70 "C, ·5510 +125 "C Throughput Rates Gain=1,(j) Gain = 2, (j) Gain = 4, (j) Gain = 8, (j) Gain =10,(j) Gain =100,(j) - 10 400 125 - 150 175 nS nS nS - - 20 1000 1100 nS nS nS 250 150 125 100 90 30 - - - - KHz KHz KHz KHz KHz KHz 500 400 -20 ±100 90 900 750 0 ±150 nS nS nS pS V/)lS 100 75 -88 0.1 200 150 nS nS dB 100 ~V/)lS +15.0 -15.0 +5.0 +78 -72 +75 2.6 +15.75 ·15.75 +5.25 +90 ·82 +90 3.0 0.01% Vdc Vdc Vdc mA mA mA Watts %FSR/%V - - - s/H PERFORMANCE Acquistion Time Full Scale Step to 0.01% Full Scale Step to 0.1% Aperture Delay Aperture Uncertainty Slew Rate Hold Mode Settling Time, 10Vto ±D.01%FS 10Vto±D.1%FS Feedthrough Rejection Droop Rate, (j) - - -50 70 -80 - - POWER SUPPLY Range, +15V -15V +5V Current, +15V ·15V +5V Power Dissipation Power Supply Rejection +14.25 ·14.25 +4.75 - - ENVIRONMENTAL Oper. Temp. Range,-Me -MM Storage Temp. Range Package Type Weight Pins 0 ·55 -65 +70 "C +125 "C +150 "C 40-pm uDIP 0.32 oz./(9 grams) max. 0.010 x 0.01 Bin. Kovar - CD Specifications valid at 25°C and over the operating temperature ranges of 0 to +70 °C and -55 to +125°C. DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 0204S-1194fTEL (50S) 339-3000fTLX 1743SS/FAX.(50S) 339-6356 HDAS-S34,-S38 Table 1. MUX Channel Addressing HDAS-534/538 OPERATION The HDAS devices accept either 8 single-ended or 4 differential input signals. Tie unused channels to SIGNAL GROUND, pin 14. Channel selection is accomplished using the multiplexer address pins shown in Table 1. Obtain additional channels by connecting external multiplexers. The acquisition time is the amount of time the multiplexer, instrumentation amplifier and sample· hold require to settle within a specified range of accuracy. The acquisition time can be measured by how long EOC is low before the rising edge of the START CONVERT pulse for continuous operation. Higher gains'require the use of the RGAIN resistor to increase the acquisition time. The gain is equal to 1 without an RGAIN resistor. Table 2 refers to the appropriate RGAIN resistors for various throughputs. The HDAS devices enter the hold mode and are ready for conversion upon the start convert going high. The c~rsion is complete within a maximum of 1 f1sec (+25°C). EOC returns low, the data is valid and sent to the three-state output buffers. The sample/hold is now ready to acquire new data. 150 nSec. ±25 nSec. MUX ADDRESS PINS 39 38 37 CA2 CAl CAD 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 CHANNEL 0 1 0 1 0 1 0 1 0 1 2 3 4 5 6 7 HDAS-534 (2-BIT ADDRESS) HDAS-538 (3-BIT ADDRESS) Table 2. Input Range Parameters INPUT RANGE GAIN RGAIN() THROUGHPUT o to +10V Oto +5V o to +2.5V o to +1.25V o to +1.OV o to +IOOmV 1 2 4 8 10 100 OPEN 2K 6650 2870 2210 200 250 KHz 150 KHz 125 KHz 100 KHz 90 KHz 30 KHz ±10V ±5V ±2.5V ±1.25V ±1.OV ±100mV 1 2 4 8 10 100 OPEN 2K 6650 2870 2210 200 250 KHz 150 KHz 125 KHz 100 KHz 90 KHz 30 KHz START CONVERT EOC t ~.1J.1S~1 -~I~L______~r___lL__________ _________ 35 nS Max. I I OUTPUT DATA _ ____________,,~~,f.-~3~5~ns~m~ax~.~~~---------I ~ - 1.8~S --r11-- I N·l VALID ENABLE ---------------~-h 10 nS max. .. I ~ 10 nS max. I Enabled Dala NVAUD -I ..... CAl ----------------~-----------" r..- CAO _____________--"-"1 CHO Notes 60 nS Typical CH1 1. A START CONVERT pulse greater than '175 nanoseconds will slow the throughput. CH2 Figure 1. HDAS-534/538 Timing Diagram 2. Bmriggering START CONVERT before EOC goes low will not start a new conversion. 3. Times shown apply over the full operating temperature range. Table 3. Zero and Gain Adjust For Immediate Assistance, Dial 1·800·233·2765 FSR Zero Adjust +1/2 LSB Gain Adjust +FS -11/2 LSB o to +IOV dc ±IOVdc +1.22mV +2.44 mV dc +9.9963Vdc +9.9927Vdc 5·13 HDAS..S34,-S38 CALIBRATION PROCEDURE 36 1. Connect the converter per Figure 2 and Table 2 for tbe appropriate full-scale range (FSR). Apply a pulse of 150 nSec (typical) to the START CONVERT input (pin 40) at a rate of 75 KHz. This rate is chosen to reduce flicker if LED's are used on the outputs for calibration purposes. 35 DGND 10 RGAINHI ~ RG-'!N 11 AGAIN LO 2. Zero Adjustments Apply a precision voltage reference source between the analog input and signal ground (pin 14). Adjust the output of the reference source per Table 3. For unipolar, adjust the zero trimming potentiometer so that the output code flickeg6tj ailY between 0000 0000 0000 and 0000 0000 0001 with BIN (pin 9) tied high (straight binary) or between 1111 1111 1111 and 1111 1111 1110 with pin 9 tied low (complementary binary). HDAS-534/538 p 20K ~_----.Jl"'16 OFFSET ADJUST +15V For bipolar operation, adjust the potentiometer such that the code flickers equally between 1000 0000 0000 and 1000 0000 0001 with pin 9 tied high (offset binary) or between 0111 1111 1111 and 0111 1111 1110 with pin 9 tied low (complementary offset binary). 3. Full-Scale Adjustment Figure 2. Typical Connection Diagram Set the output of the voltage reference used in step 2 to the value shown in Table 3. Adjust the gain trimming potentiometer so that the output code flickers equally between 1111 1111 1110 and 1111 1111 1111 for pin 9 tied high and 0000 00000001 and 0000 0000 0000 for pin 9 tied low. NOTES: 1. For unipolar operation, connect pin 12 to pin 17. 2. For bipolar operation, connect pin 13 to pin 17. 3. Position RGAIN as close as possible to pins 10 and 11. Use RN55C, 1% resistors. 4. If gain and offset adjusts are not used connect pin 15 to ground and leave pin 16 open. 4. To confirm proper operation of the device, vary the precision reference voltage source to obtain the output coding listed in Table 4. Table 4. Output Coding STRAIGHT UNIPOLAR INPUT RANGES, V dd SCALE +FS -1 LSB 7/8 FS 314 FS 1/2 FS 1/4 FS 118 FS 1 LSB 0 oto +10\1' +9.9976V +8.7500V +7.5000V +5.0000V +2.5000V +1.2500V +0.0024V O.OOOOV BIN CaMP BINARY OUTPUT CODING MSB LSB 1111 1111 1111 11100000 0000 1100 0000 0000 1000 0000 0000 010000000000 001000000000 000000000001 0000 0000 0000 OFF. BINARY INPUT RANGE BIPOLAR MSB LSB 0000 0000 0000 000111111111 001111111111 0111 1111 1111 1011 1111 1111 110111111111 111111111110 1111 1111 1111 CaMP OFF +10Vdc +9.9951 V +7.5000V +5.0000V O.OOOOV -5.0000V -7.5000V -9.9951 V -10.000V SCALE +FS -1 LSB +3/4 FS + 112 FS 0 -1/2 FS -3/4 FS -FS +1 LSB -FS BIN ORDERING INFORMATION MODELNQ. HDA8-S34MC HDA8-S34MM HDAS-S38MC HDAS-S38MM INPUT OPER. TEMP. RANGE SEAL 4 D Channels 4 D Channels 8 SE Channels 8 SE Channels O-to +70 cC -55 to + 125cC Oto+70 c C ·55 to +125 cC Hermetic Hermetili: Hermetic Hermetic Receptacle for PC board mounting can be ordered through AMP Inc.,Part # 3-331272-8 (Component Lead Socket), 40 required,.. For availability of MIL-STD-883B versions, contact DATEL. 5-14 DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-11941TEL (50S) 339-3000ITLX17438S/FAX (50S) 339-6356 HDAS-75,-76 12-Bit, 75 KHz Data Acquisition Systems bi FEATURES • • • • • • 12-8it resolution, 75 KHz 8 Channels single-ended or 4 channels differential Miniature 40-pin DDIP Full-scale gain range from 100 mV to 10V High impedance output state No missing codes GENERAL DESCRIPTION The HDAS-75,-76 are complete data acquisition systems containing an internal multiplexer, instrumentation amplifier, sample-hold, analog-to-digital converter and three-state outputs. Packaged in a miniature 40-pin double-dip package, the HDAS-75/76 has a low power dissipation of 500 milliwatts. MECHANICAL DIMENSIONS INCHES (MM) 0.810 Max. i- ~ I 0.150(3,8)Min.= The HDAS-76 provides 4 differential inputs and the HDAS-75 provides 8 single-ended inputs. An internal instrumentation amplifier is characterized for gains of 1,2,4,8,10 and 100. The gain range is selectable through an external resistor. t TECHNICAL NOTES 1. Rated performance requires using good high-frequency circuit board layout techniques, The analog and digital grounds are not connected internally. Avoid ground-related problems by connecting the analog, signal and digital grounds to one pOint, the ground plane beneath the converter. Due to the inductance and resistance of the power supply return paths, return the analog and digital ground separately to the power supplies. 20 Spaces at Intervals 0.100 (2,5) -i HI LO 10 GAIN ADJ. OUT 12 17 21 I 20 I I I I I I I HDA8-75 I HDAS-76 I I BODOM I VIEW I I I I I I I 40 I 1 1___ (15,2) 0.600 16 33 BIT 1 (MS8) CHOICHO HI 1 CHI/CHI HI CH2ICH2HI CH3ICH3 HI CH4ICHOLO CH5ICHll0 CH6ICH2LO CH7fCH3LO f-- 2 f= I-f= f= ~ 32 31 30 29 28 27 26 25 24 23 22 4:1 (76) ~} ~ ~"+>~~ MUX 12-B11 SIH 8:1 (75) NO SIGNAl 14 BI12 BIT3 BIT4 BIT5 BIT6 BIT7 BIT8 81T9 81Tl0 81Tl1 BIT12(LSB) ONO - 9 NO CONNECTION 39 CA2 38 CAl 37 CAO 19 35 ANA DIG GND GND 36 20 +5V +15V 18 ·15V 13 40 21 REF START EOC OUT CONVERT For Immediate Assistance, Dial 1-800-233-2765 0.190 (4,9) Max. 0.010 X0.018 KOVAR OFFSET BIPOLAR ADJ. 15 T U PIN 1 2 3 5 6 7 8 9 10 11 12 13 1. t5 16 17 18 19 20 • I I I I I I I I I I I I I I I I I I I I --II -- GAIN GAIN INST. AMP ~ I- U, 1 2, Double-level multiplexing allows expanding the multiplexer channel capacity of the HDAS-75 from 8 single-ended channels to 128 single-ended channels or the HDAS-76 from 4 differential channels to 32 single-ended channels. (20.6) 1 2.2 Max. (53,8) 0.100 - - (2,5) INPUT/OUTPUT CONNECTIONS PIN FUNCTION 40 STARTCNVRT 39 CA2 38 CAl 37 CAD 36 +5V 35 DIGITALGND 34 DIGITALGND 33 BITl (MSB) 32 BIT2 31 BIT3 30 BIT' 29 BIT5 28 BIT6 27 BIT 7 26 BITS 25 BIT9 24 BIT 10 23 BIT11 22 BIT 12 (LSB) 21 EOC +15V FUNCTION CHO/CHO HI CH IICH 1HI CH 21CH 2HI CH 3JCH 3 HI CH 7/CH 3LO CH6/CH2LO CH5!CH !LO CH4ICHOLO NO CONNECTION RGAINLO RGAIN HI INST. AMP OUT +10V REF OUT SIGNALGND GAINAOJ OFFSET ADJUST BIPOLAR -15V ANALOGGND 5-15 HDAS-75,-76 ABSOLUTE MAXIMUM RATINGS PERFORMANCE LIMITS PARAMETERS +15V Supply (pin 20) -15V Supply (pin 18) +5V Supply (pin 36) Digital Inputs (pins 37-40) Analog Inputs (pins 1-8) Lead Temp. (10 Sec.) UNITS Oto +18 Oto-18 -0.5 to +7.0 Vdc Vdc Vdc -0.3 to +6.0 Vdc ±25 V 300 °C FUNCTIONAL SPECIFICATIONS Apply over the operating temperature range and at ±15V de and +5V de unless otherwise specified. MIN. ANALOG INPUTS Number of Inputs HDAS·76 HDAS··75 Input Voltage Ranges Gain = 1 Gain = 100 I.A. Gain Ranges Input Impedance CHON, CHOFF Input Capacitance (·75) CH ON, CH OFF (·76) CH ON,CH OFF Input Bias Current Input Offset Current Input Offset Voltage Common Mode Volt Range CMMR, G=l,@lOHz, Vcm=IV p.p Voltage Noise (RMS) Gain = 1 Gain=8 MOX Crosstalk@l25KHz MUX ON Resistance Bies Current Tempco Offset Current Tempco Offset Voltage Tempco Input Gain equation TYP. MAX. UNITS 4 differential inputs 8 single-ended inputs Oto+tOV,±tOV oto 100 mV, ±100 mV 1011 t012 - Ohms - - 25 12 200 50 ±10 - pF pF pA pA mV V ·75 -80 - dB - - 200 50 - ±11 - "V "V dB Ohms 450 500 Doubles (max.) every 10°C above 70 °C Doubles (max.) every 10°C above 70 °C (±30 ppm/ 'C x gain) ±20 ppm/ 'C (max.) Ag = l~(gain ·1)12K] ·72 - - DIGITAL INPUTS logic Lavels Logic 1 Logic 0 Logic loading Logic 1 Logic 0 2.4 - - 0.8 - Vdc Vdc - +30 ·30 J.LA J.LA - Output Coding 5-16 2.4 - +9.9 - - +10.0 ±5 - MAX. UNITS - - - - - ±3/4 ±3/4 ±1.5 Bits LSB LSB LSB - - - ±O.13 ±O.15 ±O.25 ±0.074 ±15 ±0.074 ±5 ±O.l ±20 ±O.1 ±20 ±3/4 ±314 ±1 ±O.30 ±O.5 ±O.78 ±0.15 ±30 ±0.15 ±10 ±O.25 ±40 ±0.25 ±4O LSB LSB LSB %FSA %FSA %FSR %FSA ppm/DC %FSR ppm/DC %FSA ppm/DC %FSA ppm/DC 12 - - - - - - dB ·65 ·73 Over operating lemperature range MUX Address Set·up TIme Start Convert Pulse Width Data Valid Before rncSignal Goes Low Conversion Time, +25 °C Oto +70 'C ·5510 +125 'C Throughput Rates Gain=l,(j) Gain = 2, (j) Galn=4, (j) Gain=B, (j) Gain = 10,(j) Gain = loo,(j) 400 0.050 1 - nS "S nS "S "S "S - - - - - 12 13 13 75 60 50 45 40 10 80 70 60 50 45 20 - KHz KHz KHz KHz KHz KHz - ·50 1.4 O.B ·20 1.B 1.4 0 ±200 "S "S nS 70 90 - VI"S - 200 150 -88 400 300 nS nS dB "VI"S 300 - s/H PERFORMANCE Acqulstion Time Full Scaie Step to 0.01% Full Scale Step to 0.1% Aperture Delay Aparture Uncertainty Slew Rate Hold Mode Setiling Time, 10V 10 ±O.OI %FS 10V to ±O.I%FS Feedthrough Rejection Droop Rate, (j) - - -80 - - - - 100 +15.0 ·15.0 +5.0 +15 ·10 +25 0.500 +15.75 ·15.75 +5.25 .20 ·15 .35 0.700 0.01% pS POWER SUPPLY OUTPUTS Logic Lavels Logic 1 Logic 0 logic Loading Logic 1 Logic 0 Intamal Reference Voltage, +25 'C Drift External Current TYP. SIGNAL TIMING 1,2,4,8,10,100 - Resolution Integral NonlinearitY,25 'C Oto+70 'C ·55 to +125 'C Dlflenential Nonlinearity +25'C oto +70 'C ·55 to +125 'C F.S. Abs. Accuracy +25 'C oto +70 'C ·5510 +125 'C Unipolar Zero Error,+25 °C Unipolar Zero Tempco Bipolar Zero Error, +25 'C Bipolar Zero Tempeo Bipolar Offset Error,+25 °C Bipolar Offset Tempco Gain Error, +25 'C Gain Tempco Harmonic Distortion (. FS) (DC to 5KHz,10V pk.pk) (j) No Missing Codes MIN. - Vdc Vdc 0.4 ·500 1.6 "A rnA +10.1 ±35 1.5 Vdc ppm/DC rnA Siraighl binary/Offset binary Range+15V ·15V +5V Curnent +15V ·15V .5V Power Dissipation Power Supply Rejection +14.25 ·14.25 +4.75 - - - Vdc Vdc Vdc rnA rnA rnA Watts %FSRI%V ENVIRONMENTAL Opar. Temp. Range, ·MC, ·PC -MM Storage Temp. Range Package Type Weight 0 -55 -65 - +70 'C +125 'C +150 'C 40-pin DDIP 0.32 oz.l(9 grams) max. - (j) Specifications valid at 25 'C and over the temperallJre ranges of 0 to +70 'C and -55 to +125 'C. DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194fTEL (508) 339-3000fTLX 174388/FAX (508) 339-6356 HDAS·75,·76 Table 2. Input Range Parameters HDAS-75176 OPERATION The HDAS devices accept either 8 single-ended or 4 differential input signals. Tie unused channels to SIGNAL GROUND, pin 14. Channel selection is accomplished using the multiplexer address pins shown in Table 1. Obtain additional channels by connecting external multiplexers. The acquisition time is the amount of time the multiplexer, instrumentation amplifier and sample-hold require to settle within a specified range of accuracy aiter the start convert goes high. The acquisition time can be measured by how long EOC is low before the rising edge of the START CONVERT pulse for continuous operation. Higher gains require the use of the RGAIN resistor to increase the acquisition time. The gain is equal to 1 without an RGAIN resistor. Table 2 refers to the appropriate RGAIN resistors for various throughputs. INPUT RANGE GAIN RGAIN 1 2 4 8 10 100 OPEN 2KO 6650 2870 2210 200 75KHz 60KHz 50KHz 45KHz 40KHz 10KHz 1 2 4 OPEN 2KO 6650 2870 2210 200 75KHz 60KHz 50KHz 45KHz 40KHz 10KHz 01o+10V 01o+5V 0Io+2.5V 0Io+1.25V 0Io+1.0V 01o+100mV ±10V ±5V ±2.5V ±1.25V ±1.0V ±100mV 8 10 100 THROUGHPUT Rgain= [ 1 -- (9:~-1)J Table 1. MUX Channel Addressing 36 +5V ~ 1 MUX ADDRESS PINS 39 38 37 CA2 CAl CAO 4.7 11FT .111if DGND .J.. 34,35 . -1.Q RGAINHI i__ -1.1 RGA'. CHANNEL o RGA~LO o o o HDAS-76 (2-BIT ADDRESS) 1 1 HDAS-75 (3-BIT ADDRESS) 1 10V REF o 1r ·1 1'F { 4.7I'Fr ~ 13 HDA5-75176 1 19 -15V~ 20K 15 GAIN ADJUST -15~J +15V 16 OFFSET ADJUST 20K +153 -15V 4.71'F t 4.7 11F r +15Vo + 2. Zero Adjustments Apply a precision voltage reference source between the analog input and signal ground (pin 14). Adjust the output of the reference source per Table 3. For unipolar, adjust the zero trimming potentiometer so that the output code flickers equally between 0000 0000 0000 and 0000 0000 0001. 18 tll1~9 For bipolar operation, adjust the potentiometer such that the code flickers equally between 1000 0000 0000 and 1000 0000 0001. rll'F 20 3. Full-Scale Adjustment Figure 2. Typical Connection Diagram NOTES: 1. For unipolar operation, connect pin 12 to pin 17. 2. 3. 4. 5. For bipolar operation, connect pin 13to pin 17. Ground pin 15 il Gain Adjust is not used. leave pin 16 open n offset adjust is not used. Posnian RGAIN as ciose as possible to pins 10and 11. Use RN55C, 1% Set the output of the voltage reference used in step 2 to the value shown in Table 3. Adjust the gain trimming potentiometer so that the output code flickers equally between 1111 1111 1110and 111111111111. 4. To confirm proper operation of the device, vary the precision reference voltage source to obtain the output coding listed in Table 4. resistors. CALIBRATION PROCEDURE 1. Connect the converter per Figure 2 and Tables 2 and 3 for the appropriate full-scale range (FSR). Apply a pulse of 1,0 llSec (typical) to the START CONVERT input (pin 40) at a rate of 75 KHz. This rate is chosen to reduce flicker if LED's are used on the outputs for calibration purposes. For Immediate Assistance, Dial 1-800-233-2765 Table 3. Zero and Gain Adjust FSR Zero Adjust +112 LSB a +1.22mV +2.44 mVdc to +10V dc ±10V dc Gain Adjust +FS - 1112 LSB +9.9963Vdc +9.9927Vdc 5-17 HDAS-75,.;76 TIMING EOC The output signal, when high, indicates that a conversion is in process. During a conversion the digital output buffers are in a high impedance state, preventing data from being read. A START CONVERT input received during a conversion has no effect on the existing conversion. As shown in Figurela, data can be read while START CONVERT is high and EOC is low. I .....1 START CONVERT EOC The AID conversion begins on the falling edge of a start convert command. If START CONVERT stays low after EOC becomes low, the output buffers stay in a high impedance state. Valid data can be read 150 nanseconds maximum after START CONVERT goes high. Figure 1b shows how to use the START CONVERT pulse to. control when the output data ' becomes valid. 1-- 200 nS Max ___ I ;.,.. 50 nS Miin. I . ~-'-I-c~2c-"-=-se-:-·ci-I--" __ I '------+--~-+------' 150 n$ Max. NVALID --I 1--I I HIGH OUTPUT DATA II -~--~~ EOC DATA +l--N_ _ _ I I OUTPUT --'r--- CONVERT'.,-_N._'_,-1_ _ _----' ---->11'--_--.-_--'11'--___ ___ 300 nS Min. - - :__ 200 nS Max I START --I N-l I L---_ __ 1-25nSMin. HIGH N __---'--_-----'IM::::P-=E=DA.:::N::::CE=--_----'_.!.'VA~L~ID__..L_.:IM:_:P.::ED~A:::N~CE=____L.Y.!VAU0 CA1 -~-----_4------~ Figure lb. Data Valid with START CONVERT Returned High Later CAO ________~~~IJI--~6c6o~nS~T~~~lc~ru-------I I NOTES: Figure la. . Data Valid with START CONVERT Immediately Returned High t. A START CONVERT pulse greater than 5 ~S will slow the overall throughput. 2, Retriggering START CONVERT bafore E'O'C'" goes low will not initiate a new conversion. 3. Timing specifications apply over the full operating temperature range. Table 4. Output Coding STRAIGHT BIN UNIPOLAR INPUT RANGES, V de OUTPUT CODING SCALE +FS -1 LSB 7/8 FS 314 FS 112 FS 1/4 FS 118 FS 1 LSB 0 Oto+l0V +9.9976V +8.7500V +7.5000V +5.0000V +2.5000V +1.2500V +0.0024V O.OOOOV MSB LSB 1111 1111 1111 111000000000 1100 0000 0000 1000 0000 0000 010000000000 001 0 0000 0000 000000000001 0000 0000 0000 OFF BINARY INPUT RANGE BIPOLAR +10Vde +9.9951V +7.5000V +5.0000V O.OOOOV -5.0000V -7.5000V -9.9951V -10.000V SCALE +FS -1 LSB +3/4 FS +1/2 FS 0 -1/2 FS -3/4 FS -FS +1 LSB -FS ORDERING INFORMATION MODEL NO. HDAS-76PC HDAS-76MC HDAS-76MM HDAS-76/883 HDAS-75PC HDAS-75MC HDAS-75MM HDAS-75/883 INPUT 4D Channels 4 D Channels 4 D Channels 4D Channels 8 SE Channels 8 SE Channels 8 SE Channels 8 SE Channels OPERATING TEMP. RANGE Oto +70 °C oto +70 °C -55to+125°C -55 to +125 °C Oto+70°C Oto+70°C -55 to + 125°C -55 to +125 °C SEAL Plastic Hermetic Hermetic Hermetic Plastic Hermetic Hermetic Hermetic Receptacle for PC board mounting can be ordered through AMP Inc.,Part # 3-331272-8 (Component Lead Socket), 40 required. 5-18 DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194ITEL (508) 339-3000ITLX 174388/FAX (508) 339-6356 HDAS-950/-951 16-Bit, 100 KHz Data Acquisition Systems PRELIMINARY PRODUCT DA TA FEATURES • 16-8it resolution, 100 KHz • 8 Channels single-ended or 4 channels differential • Miniature 40-pin DDIP • Full-scale gain range from 100 mV to 10V • High-impedance output state GENERAL DESCRIPTION The HDAS-950/-951 are complete data acquisition systems containing an internal multiplexer, instrumentation amplifier, sample-hold, analog-to-digital converter and three-state outputs. Packaged in a miniature 40-pin double-dip package, the HDAS-950/-951 have a low power dissipation of 2.4 watts. The HDAS-951 provides 4 differential inputs and the HDAS950 provides 8 single-ended inputs. An internal instrumentation amplifier is characterized for gains of 1, 2, 4, 8, 10 and 100. the gain range is selectable using an external resistor. TECHNICAL NOTES 1. Use external potentiometers to remove system errors or the small initial errors to zero. Use a 20K trimming potentiometer for gain adjustment with the wiper tied to pin 12 (ground pin 12 for operation without adjustments). Use a 20K trimming potentiometer with the wiper tied to pin 11 for zer%ffset adjustment (leave pin 11 open for operation without adjustment). 2. Bypass the analog and digital supplies and the + 1OV reference (pin 9) to ground with a 4.7I!F, 25V tantalum electrolytic capacitor in parallel with a 0.1 I!F ceramic capacitor. Bypass the +1OV reference (pin 9) to analog ground (pin 33). 3. Rated performance requires using good high-frequency circuit board layout techniques. the analog and digital grounds are not connected internally. Avoid ground'related problems by connecting the analog and digital grounds to one pOint, the ground plane beneath the converter. Due to the inductance and resistance of the power supply return paths, return the analog and digital ground separately to the power supplies. 4. Double-level multiplexing allows expanding the multiplexer channel capacity of the HDAS-950 from 8 single-ended channels to 128 single-ended channels or the HDAS-951 from 4 differential channels to 32 single-ended channels. UNIPOLAR 10 MUX ENABLE AMP IN LO (951) AMP IN HI RGAIN HI RGAIN LO '---l-.-r~~,---J 30 81T 1 (MSB)I BIT 9 29 BIT 21 BIT 10 28 8113181111 CHOJCHOHI CHI/CHI HI CH2/CH2HI 27 26 25 24 81T4I81112 BIT 51 BIT13 81T6IBIT14 BlT71BIT15 23 BIT 81 BIT 16 (lSB) CH3ICH3Hl CH4ICH3 LO CH5ICH2l0 CH6.iCHl LO ~950) CH7/CHOLO f------~ 17 FSTATI f------~ 18 FSTAT2 L__J:=====~ 37 36 35 33 CA2 CAl CAO ANA 13 DIG aND GND (950) +SV 32 31 +15V -15V INPUT/OUTPUT CONNECTIONS , - - - - - 15 ENABLE (9·16) ,--_ _, - -_ _',7_ _',._--.,39_ _',B_ _ _ _r-+_~-----'f_+_-~ 16 ENABlE(1·8) 20 +10V REF 22 FIFOIffiR 19 FIFOAEAO -- PIN FUNCTION PIN FUNCTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 CHO/CHOHI CH 1/CH 1 HI CH 21CH 2 HI CH 3/CH3 HI CH4ICH3LO CH5ICH2LO CH6ICH 1 LO CH7ICHOLO +10V REF. OUT UNIPOLAR OFFSET ADJUST GAIN ADJUST DIGITAL GROUND +5VPOWER ENABLE (9·16) ENABLE (1·8) FSTATl FSTAT2 FIFO READ START CONVERT 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 AMP IN HI RGAIN HI RGAINLO CA2IAMPIN LO CAl CAO MUXENABLE ANALOG GROUND +15V POWER -15VPOWER BIT 1(MSBY BIT 9 BIT 21 Brr 10 BIT3/BIT11 BIT 41 BIT 12 BIT 51Brr 13 BIT 61 BIT 14 Brr7/BIT15 BIT 8LIDJ16 (LSB) FIFO/DIR EOC 17 18 19 20 START CONVERT EOC OUT For Immediate ASSistance, Dial 1-800-233-2765 5-19 HDAS·950/·951 ABSOLUTE MAXIMUM RATINGS PARAMETERS PERFORMANCE UNITS LIMITS +15V Supply (pin 32) -15V Supply (pin 31) +5V Supply (pin 14) Digital Inputs (pins 15-20, 22, 34-37) Analog Inputs (pins 1-8) Lead Temp. (10)Sec.) 010+18 010 -18 -0.510 +7.0 Vde V de V de -0.3 to Voo +0.3 ±14 300 V de V °C FUNCTIONAL SPECIFICATIONS Apply over the operating temperature range and al ±15V de and +5V de unless olherwise specified. ANALOG INPUTS MIN. Number of Inputs HDAS-950 HDAS-951 Input Voltage Ranges Gain = 1 Gain = 100 I.A. Gain Ranges Gain Equation Error Input Impedance CHON,CHOFF Input .Capacitance (-950) CH ON, CH OFF (-951) CH ON.CH OFF Input Bias Current Input Offset Current Input Offset Voltage Common Mode Volt. Range CMMR, G=I,@10Hz, Vern=IVp-p Voltage Noise (RMS) Gain = 1 Gain = 8 MUX Crosstalk @100 KHz Bias Current Tempco Offset Current Tempeo Offset Voltage Tempeo Input Gain Equation TYP. MAX. UNITS 8 single-ended inpuls 4 differential inpuls - 010 +10V de, ±SV de Oto 100 mV de, ±SO mV 1,2,4,8,10,100 :!ll.1 Yo 1013 1014 - Ohms - - 25 12 500 20 pF pF nA nA mV V ±10 :tQ - - - -110 - - - TBD TBD dB IN IN -72 dB Doubles (max.) every 10 "C above 70 "C Doubles (max.) every 10 "C above 70 "C (BO ppml "C x gain):tQO ppm/ "C (max.) Rg = 2K1(gain -1) DIGITAL INPUTS Logic Levels Logic I Logic 0 Logic Loading Logic 1 Logic 0 2.25 - - - - 0.8 Vdc Vdc - - +5 -200 jJA jJA - OUTPUTS Logic Levels Logic I Logic 0 Logic Loading Logic I Logic 0 Internal Reference Voltage, +25 "C Drift External Current Output Coding - 0.4 Vdc Vdc - - -160 6.4 jJA rnA +9.9 - - Vdc +10.1 MO ppml"C 5 mA Straight binary/Olfset binary +10.0 ±15 - NOTES: Specifications valid at 25°C and 'over the. operating temperature ranges of 0 to +70 °C and -55 to +125 °C. (!) @ Pulse widths greater than 5 I1Sec. will decrease the specified throughput rate. 5-20 MIN. TYP. MAX. 16 - - - - - - - - - - - :!ll.006 :!ll,012 TBD :!ll,006 :!ll.012 TBD :!ll.15 TBD TBD :!ll,05 TBD :!ll.05 TBD :!ll.1 TBD :!ll.1 TBD UNITS Bils %FSR %FSR %FSR %FSR %FSR %FSR %FSR %FSR %FSR %FSR ppml"C %FSR ppm/"C %FSR ppml"C %FSR ppm/"C -78 dB TBD dB Over operaling lemperalure range - SIGNAL TIMING Enable to Data Val. Delay MUX Address Sat-up Time Start Convert Pulse Width, @ Data Valid After EOC Signal Goes Low Conversion Time, 100 megohms in parallel with 2 pF. TECHNICAL NOT.ES 1. The transfer accuracy of these multiplexers depends on both the source resistance and the load resistance. With zero source resistance, and assuming 2K ohms maximum channel ON resistance, the load impedance should be at least 20 megohms to achieve 0.01% accuracy. In practice, it is recommended that a load impedance of at least 100 6-6 megohms be used to minimize errors. Source resistance should be kept as low as possible so that accuracy is not affected; less than '1 K ohms is recommended. Higher source resistance, in addition to affecting accuracy, will degrade the settling time of the multiplexer. 2. Channel expansion uses the inhibit input of the multiplexer. A logic 0 on this input disables the mulitplexer. DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194fTEL (508) 339-3000fTLX 174388/FAX (508) 339-6356 MX Series mill idA £ CONNECTION & APPLICATION CHANNEL ADDRESSING PIN CONNECTIONS CAl ,. INHJB 15 CA' CM -Vs liN 2IN 14 GND 13 12 +Vs SIN 151N 24 3IN 11 .,N 141N 23 "N SIN 41N 10 71N 131N 22 41N 121N 21 3IN 1tlN 20 I. "N liN MX-808 MX-l606 OUT ,. ---OUT NC 27 26 -Vs 81N 161N 2S 7IN 10 +Vs NC "N to IN 10 "N GND VA CAB MXD-409 CAl ,. I. INHIB IS I. 17 INHIBIT AI 16 CA' " 15 CA' CA2 GND -Vs I. lAIN· 13 2A IN- 12 28 IN 3A IN 11 38 IN MXD-807 +Vs laiN .Vs BOUT BOUT A OUT NOTES: 1. -Vs 26 8A IN 88 IN 25 7A IN 7BIN 2. BAIN 6B IN 23 SA IN 58 IN 22 4A IN 48 IN 21 3A IN • 28IN ~ 4 2 ON INHIB. CHANNEL 1 4 2 1 X X X X a NONE X X X a a 0 a a a a a 1 a a 1 a a a 1 1 a 1 a a a 1 a 1 1 1 0 0 0 1 1 1 2 a 0 1 1 2 1 3 0 1.0 1 3 1 4 0 1 1 1 4 1 5 1 0 0 1 5 1 6 1 a 1 1 6 NONE 0 1 1 0 1 7 1 1 0 1 7 0 1 1 1 1 8 1 1 1 1 8 1 0 0 0 1 9 1 0 0 1 1 10 1 0 1 0 1 11 1 a 1 1 1 12 X X 0 1 1 0 a 1 13 0 0 1 1 1 0 1 1 14 0 1 1 2 MXD·409 ON INHIB. CHANNEL 1 2 NONE ,.,. lAIN 1 INHIBIT 1 1 1 0 1 15 1 0 1 3 1 1 1 1 1 16 1 1 1 4 20 10 ON INHIB. CHANNEL 8 A OUT 27 38 IN NOTES: CA CHANNEL ADDRESS SUPPLY VOLTAGE REFERENCE VOLTAGE NO CONNECTIONS ,. NC 48 IN 10 4A IN 11 12 13 MX·808. MXD-807 MX·1606 2A IN 18 IN 11 GND 12 VA NC I. 17 16 CA2 I. IS CA4 CAl SETTLING TIME VS. SOURCE RESISTANCE (20V STEP) LEAKAGE CURRENT VS. TEMP. 1000 lOOnA IOnA .III 100 /' OFFOUTPUr LEAKAGE CURRENT '0 (OFF) ¥ TOO_\: V 10 -..... ON LEAKAGE I ~ ./ 1M CURRENT '0 (ONI /' ~ :......: ~ ..... --- TO 0.01% // y / 0.1 0.01 ~ 0.1 100 10 SOURCE RESISTANCE (RsJ in KILOHMS ./ ./ 100 pA / OFF INPUT LEAKAGE CURRENT V 'SCOFF) ORDERING INFORMATION Ll' CHANNELS OPERATING TEMP. RANGE MX-808 8 S.E. oDe to +70 o e MX·1606 16 S.E. oDe to +7o o e MXD·409 4 Dill. oDe to + 70 0 e MXD·807 8 Dill. oDe to + 70 0 e MODEL NO. SOO 750 1000 TEMPERATURE ("e) For Immediate ASSistance, Dial 1-800-233-2765 6-7 Contact DATEL for up-to-date information on products covered by "Advanced" and "Preliminary" product data sheets. Dial 1-800-233-2765 for Applications Assistance 6-8 DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194fTEL (508) 339-3000fTLX 174388/FAX (508) 339-6356 MX-1616, MX-818 High-Speed CMOS Analog Multiplexers MECHANICAL DIMENSIONS INCHES (MM) FEATURES • • • • • ,. 800 Nanoseconds settling time Programmable input mode Break-before-make switching Dielectrically isolated CMOS TIUCMOS-compatible T '0 r DATEL 0.3'0 17.87) 0.29' 17.'9) MX-818 -L ly,,-"TT""TT""TT"T"T"""T-rrr~ l f-- GENERAL DESCRIPTION The MX-1616 and MX-818 are high-speed high performance analog multiplexers manufactured with a dielectrically isolated CMOS process. Both devices achieve transfer accuracies of 0.01% at channel sampling rates of up to 1.25 MHz over ±1 OV signal ranges. These multiplexers are ideal for high-speed, multichannel, data acquisition systems where the multiplexer operates into a high impedance load such as a sample-hold, buffer amplifier or instrumentation amplifier. 0.185 MAX. 0.900 ± 0.015 (22.9 :l: 0.381) -------1 ----I 0.040 t: 0.020 (1.02 0.100 TYP. (2.54) MX-1616 ~ OUT MX·1616 " 16 - 17 - ~,~---_,++; ,. ~ 32 GAO CA' CA2 GAO INHIS ADDRESS GAO CA' CA2 CA3 ~ DECODER 8A IN C~ ~r----rrHHH 33 ANAlOG OUT CHANNEL 112 A OUT ~ W OUT MX-1616 GAO 0.... 1'3,2) ~-~~~~~~~ ,. - G.'j}------n-i I DATEL ANAlOG IN INHIBIT :I: 0.508) " 28 A unique feature of these circuits is tha ability of the use to program their inputs for either single-ended or differential operation, The MX-1616 is user programmable either as a single-ended 16-channel or as a differential 8-channel multiplexer while the MX-818 is user programmable either as a single-ended 8-channel or as a differential 4-channel multiplexer. LS (~,70) - OUT -eGA< ,--
•.••••..••••• 7500 Channel ON Res. over Temp., maximum> ••••••• 1 KO Channel OFF Input Leakage •.•.•.••..•..•. 10 pA Channel OFF Output Leakage ..•.•.•••.•.••• 35 pA Channel ON Leakage •.•.••• 40 pA Channel OFF Input Capacitance •.•••••••••• 2.5 pF Channel OFF Output Capacitance .••••••••••• 18 pF MX-818 8 Single-Ended 4 Differential · · +0.8V +0.3V +2.4V 0.7 (Logic sup.) 1 pA 25pA 4 B~s Logic "0" 0.01% 250 nsec. 800 nsec. 150 nsec.4 150 nsec. 125 nsec. 20 nsec. pends upon both the source and the load resistance. With zero source resistance and assuming 1 KO maximum chane I on resistance the load impedance must be at least 10 MO to achieve 0.01% accuracy. Source resistance should be kept as low as possible so thaI accuracy or settling time are not degraded. Less than 5000 is recommended. 50 pA 1.9 pF 10 pF 2. Channel expansion is accomplished by the use of the inhibit input of the multiplexers. To expand the number of channels, use multiple multiplexers with the inhibit inputs connected to a decoder. ·· ·· · 20 pA 3 Bits · PERFORMANCE Transfer Error, maximum .•. Settling TIme, 10VsteptoO.l% ••••... 10VsteptoO.Ol% •••... Access Time, maximum ..•. Enable Delay "ON", maximum ••.••••• Enable Delay "OFF", maximum ......• Break Before Make Delay ... 1. The transfer accuracy of the MX-1616 and MX-818 de- l00pA 100 pA DIGITAL INPUTS Logic "0" Threshold, maximum: TTL •••••••••. CMOS .•.•.•.• Logic "1" Threshold, minimum: TTL ••.•..••.. CMOS ..•....• Input Leakage Current, maximum: High " . . • . . .. Low ....•.... Channel Address Coding .... Channel Inhibit, All Channels OFF •••.•... TECHNICAL NOTES · ·· PIN CONNECTIONS MX-818 MX-1816 +Vs 2. ADUT BOUT 27 -Vs 28 +Vs 1. A OUT BOUT 17 -Vs SAIN SA IN 48 IN 88 IN 2. 7AIN 3BIN ,. lS IN 2. BAIN 29 IN 14 2A IN 6BIN 23 BA IN 1a IN 13 1A IN 58 IN 22 4A IN GND 12 INHIBIT 48 IN 21 3AIN LS 11 CAD CA> 10 CA1 NC 38 IN 20 2A IN 125 nsec." 28 IN 10 · ·· 11 ,. fAIN 18 IN INHIBIT GND 12 17 CAD LS 13 CAl " ,. CA1 19 16 16 4AIN NOTES: CA CHANNEL ADDRESS Vs SUPPLY VOLTAGE LS LOGIC SELECT NC NO CONNECTION CA2 POWER REQUIREMENTS Rated Power Supply Voltage .•.•.•.•.. ±15V Quiescent Current maximum ±30 mA Power Dissipation', ••••••••• maximum •.•••••••••.•• 900 mW 6-10 · ±18 mA 540mW DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194fTEL (508) 339-3000fTLX 174388/FAX (508) 339-6356 MX-1616, MX-818 CONNECTION & APPLICATION MX·1616· USED AS 16 CHANNEL MULTIPLEXER USE CAl AS DIGITAL ADDRESS INPUT CONNECT A OUT TO BOUT ON CHANNEl TO OUTPUT B 3 1 1 o INHIB. OUPUT A X X X X 0 NONE NONF 0 0 0 0 1 lA -- 0 0 0 1 1 2A -- 0 () 1 0 1 :IA -- 0 () 1 1 1 4A 0 1 0 () 1 5A -- 0 1 0 1 1 bA 0 1 1 0 1 7A --- 0 1 1 1 1 8A -- -- I 0 0 0 1 -- 1 0 0 1 1 -- 28 1 0 1 0 1 -- 38 ---- 48 18 1 0 1 1 1 1 1 0 0 1 1 1 0 1 1 1 1 1 0 1 -- 78 1 1 1 1 1 -- 88 MX-818· USED AS 8 CHANNEL MULTIPLEXER USE CAl AS DIGITAL ADDRESS INPUT 2 2 1 ON CHANNEl TO o INHIB. INHIB. OUTPUT A OUTPUT B X X X 0 NONE NONF 0 0 1 lA 0 0 1 1 2A --- 0 1 0 1 .lA -- 0 1 1 1 4A -- ---- 1 0 0 1 1 0 1 1 1 1 0 1 1 1 1 1 1 8 2 B 3 8 4 B 58 68 MX·1616· USED AS DUAL 8 CHANNEL MULTIPLE"ER OUTPUT A o 0 MX-818· USED AS DUAL 4 CHANNEL MULTIPLEXER CONNECT CAl TO, -V SUPPLY 1 CONNECT CAl TO -V SUPPLY 1 CONNECT A OUT TO BOUT ON CHANNEl TO OUTPUT B X X X 0 NONE NONE 0 0 0 1 lA 1B 0 0 1 1 2A 2B 0 1 0 1 3A 3B 4B 0 1 1 1 4A 1 0 0 1 5A 58 1 0 1 1 6A 68 1 1 0 1 7A 7B 1 1 1 1 8A 88 ON CHANNEIi TO 0 INHIB. OUTPUT A OUTPUT B X X 0 NONE NONE 0 0 1 1 1B 0 1 1 2 2B 1 0 1 3 38 1 1 1 4 4B ORDERING INFORMATION For Immediate Assistance. Dial 1·800-233-2765 MODEL NO. CHANNELS OPERATING TEMP. RANGE MX·818C MX·1616C 8 S.E. or 4 Dill.. 16 S.E. or 8 Dill .. OI0+70°C 010 +70 °C 6-11 Contact DATEL for up-to-date information on products covered by ':Advanced" and "Preliminary" product data sheets. Dial 1-800-233-2765 for Applications Assistance 6-12 DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194fTEL (508) 339-3000fTLX 17438B/FAX (508) 339-6356 MX-826 Precision, High-Speed Multiplexer FEATURES 225 nSec. maximum settling time to 0.01% 400 nSec. maximum settling time to 0.003% 150 nSec. maximum settling time to 0.1% • 8 Channels single-ended inputs 395 mW Power dissipation • Small 24-pin DDIP package MECHANICAL DIMENSIONS INCHES (mm) GENERAL DESCRIPTION The MX-826 is''a precision high-speed multiplexer characterized for 10-. 12-. and 14;bit applications. The performanca benchmarks are its 225 nanoseconds maximum settling time to 0.01% accuracy and its unprecedented specification of accuracy to 0.003%. 0.600MAX (20,3) '1 0.190 MAX ~0.010 x0.016 ~ KOVAR Pins The MX-826 provides eight single-ended inputs. Channel addressing is done by a three-bit binary code. Break-balore-make switching assures that no two channels are ever momentarily shorted together. 13 ,12 ,,, ,, ,, ,, ,, ,,, , ,,, The MX-826 operates from ±15V and +5V power sup· plies. Models are available in two operating temperature ranges: 0 to +70 °C and -55 to +125 °C. BOTTOM VIEW , , ,I ,,, ,, ,, , ,, ,,, , ! 1 I 24 ! 1~ ---.l 0.150 MIN. (3,6) Tl 11 SPACES ATO.l00 (2,5) 1.310 MAX. (33,3) -hL 0.600 (15,2) NOTE: Pins have a 0.025 inch, ±O.01 stand-off from case. -15V +15V 16 INPUT/OUTPUT CONNECTIONS 4 PIN FUNCTION PIN FUNCTION AO A1 A2 IN1 IN2 IN3 IN4 IN5 IN6 IN7 IN8 GROUND 13 14 15 16 17 18 19 20 21 22 23 24 OUTPUT N/C N/C +15V (+Vcc) GROUND GROUND -15V (-VEE) N/C N/C N/C GROUND +5V (+VDD) 5 ANALOG INPUTS 6 7 13 >--+-- OUTPUT 8 9 10 11 1 2 3 4 5 6 7 8 9 10 11 12 CHANNEL ADDRESS Figure 1. MX-826 Simplified Block Diagram For Immediate Assistance, Dial 1-800-233-2765 6-13 !w~[L. MX·826 ABSOLUTE MAXIMUM RATINGS POWER SUPPLY REQ. PARAMETERS LIMITS +15V Supply (Pin 16) -15V Supply (Pin 19) +5V Supply (Pin 24) Digital Inputs (Pins 1,2,3) Analog Inputs (Pins 4-11) Lead Temperature (10 sec.) Short Circuit to Ground o to +18V dc o to -18V dc -0.5 to +7V dc -0.3 to +5.5V dc -15 to +15V dc 300'C Continuous FUNCTIONAL SPECIFICATIONS Apply over the operating temperature range and over the operating power supply range unless otherwise specified. INPUTS Input Voltage Ranges Digital Input, Logic' Level Logic 1 LogiaO Logic .Loading Logic 1 Logic 0 MIN TYP MAX ±10.0 ±10.5 - Vdc 2.0 - 0.8 Vdc Vdc - 1 -1 !iA !iA ±10.5 - Volts mA pF Ohms - - UNITS OUTPUTS Output Range Output Current Stable Capacitive Load Output Impedance DC ±10.0 15 - - - - 0.1 - -1 - 100 - PERFORMANCE Gain Gain Error, 25 'C Gain Tempco, -55 to +125'C Offset, 25 'C Offset Voltage Drift Slew Rate • CrossTalk 100 KHz 1 MHz Bandwidth 3 dB Small Signal Full Power Input Impedance Output Settling Time ." (10V step, +25 'C) 5000 Load 0.1%10 Bits 0.01% 12 Bits 0.003% 14 Bits f?!JI/S1Iip,+25'C)lKOI..oa:l 0.1% 10 Bits 0.01% 12Bits 0.003% 14 Bits Switching Characteristics Break before make delay Turn OnlTurn Off Harmonic Distortion DC to 100 KHz, 10V pp +25'C -55 to +125'C lMHz 10Vpp +25'C -55 to +125'C DC to 100 KHz 20V pp +25'C -55 to +125'C 1MHz t020V pp +25 'C -55 to +125 'C Signal-to-NolseRatill with Distortion withoul Distortion 6-14 - - - 200 ±0.5 ±D.l <5 300 -82 -64 -86 -69 8 3 2.45 8.5 3.5 2.5 - - ±D.03 ±5 ±0.5 ±10 - FS %FS ppm/'C mV IlV/'C V/IlS - dB dB 2.55 MHz MHz KO 100 150 300 150 225 400 nS nS nS - 150 200 600 180 240 720 nS nS nS - 8 15 20 25 50 nS nS -90 -88 -92 -92 - -75 -70 -85 -85 - dB dB -87 -85 -89 -89 -72 -67 -83 -83 -69 -75 -72 -80 - Range +15V -15V +5V Current (Quiescent) +15V -15V +5V Power Supply Reject Ratio Power Supply Dissipation MIN TYP MAX UNITS +14.5 -14.5 +4.75 +15 -15 +5 +15.5 -15.5 +5.25 Volts Volts +13 -13 <1 +19 -19 +1 395 575 86 Volts mA mA mA dB mW PHYSICAUENVIRONMENTAL Operating Temp. Range -MC Models -MM Madels Storage Temp. Range Package Type Pin Type Weight o +70 'C -55 +125 'C -65 +150 'C 24-pin herm. sealed ceramic I 0.010 x 0.018 inch Kovar 0.42 oz. (12 gram) maximum TECHNICAL NOTES 1. Bypass the ±15V and +5V power supplies with a 1 I1F, 25V tantalum electrolytic capacitor in parallel with a 0.1 I1F ceramic capacitor. 2. Analog signals up to ±15V may be present while the MUX power supplies are off. 3. The absence of an RON specification or output leakage specification is related to the architecture of the switching network. The inputs see a constant 2.5 K Ohm input impedance whether the channel is on or off. 4. Typical recovery times from an overvoltage condition of >±3V is approximately 200 nanoseconds from a negative overdrive and 700 nanoseconds from a positive overdrive. 5. Double level multiplexing may be used to provide up to 64 channels (nine MX-S26's required). Table 1. .',Channel Addressing On Channel MUX Address A2 A1 AO .. 1 2 0 0 0 0 0 1 3 4 0 0 1 1 0 1 5 1 0 0 6 1 0 1 7 1 1 0 S 1 1 1 ORDERING INFORMATroN' dB dB Model No/Channels .Oper, Temp. Range - dB dB MX-S26MC MX-S26MM - - dB dB - dB dB SSE SSE Oto +70 'C -55 to +125'C Order PC board mounting receptacle through AMP Inc., Part #3-331272-S (Component Lead Socket), 24 required. For availablilty of MIL-STD-SS3B version contact DATEL. DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194rrEL (50S) 339-3000rrLX 174388IFAX (508) 339-6356 MX-850 Precision, High Speed Multiplexer FEATURES 50 nSec settling time to 0.01% 70 nSec settling time to 0.003% 100 nSec settling time to 0.001% 4 Channels,~ single-ended inputs • 207 mW power dissipation Small 14-pin DIP package GENERAL DESCRIPTION The MX~850 is a precision high·speed multiplexer character~ ized for 10~. 12~. 14-. and 16-bit applications. The performance benchmarks are its 50 nanosecond maximum settling time to 0.01 % accuracy and its unprecedented specification of accuracy to 0.001%. MX-850 Mechanical Dimensions INCHES (mm) 0.500 MAX. I I (12.7) TECHNICAL NOTES 1. Proper operation of the MX-850 multiplexer is dependent upon good board layout and connection practices. Bypass supplies as shown in the connection diagrams. Mount bypass capacitors directly to the supply pins whenever possible. 0.010 x 0.D18 KOVAR Pins 2. All grounds pins (9. 11, 13) should be tied together and connected to ground as close to the multiplexer as possible. n n 3. When power is off. current limit input signals on pins 4. 5, 6. and 7 to 20 mA. Failure to current limit will cause permanent damage to the device. as when powering up or down. it is possible that two switches might be on at the same time. Excessive current (greater than 20 mA) will flow from the more positive input to the more negative input. permanently damaging the device. Applications where the power supply for the multiplexer also powers the signal sources may not require limiting resistors. See Figure 4. P 1 8 0 0 BOTTOM n o VIEW n n 0 0 6 SPACES 0.800 MAX. (20.3) AtO[jlOO (2,5) J 14nl- nl 0.300 (7,6) NOTE: Pins have 0.025 Inch from case. to.ol stand~Off +15V 10 CH1 CH2 4 5 8 6 12 OUTPUT PIN FUNCTION 1 2 3 ENABLE AO Al CH 1 INPUT CH21NPUT CH31NPUT CH41NPUT OUTPUT GROUND +15V GROUND +5V GROUND -15V 4 CH3 +5V 5 6 7 CH4 8 7 I EN 9,11,13 I 14 GROUND -15V 9 10 11 12 13 14 MX-850 Simplified Block Diagram For Immediate Assistance. Dial 1-800-233-2765 6-15 MX·850 ABSOLUTE MAXIMUM RATINGS PARAMETER +15V Supply (pin 10) -15V Supply (pin 14) +5V Supply (pin 12) Digital inputs (pins 1, 2, 3) Analog inputs (pins 4, 5, 6, 7) Analog Input Current Lead temperature (10 Sec) Switching frequency/duty cycle SWITCHING CHAR. (cont.) LIMITS UNITS -0.5 to +16.5 +0.5 to -16.5 -0.5 to +7.0 -0.5 to +6.0 -10.5 to +10.5 ±20 300 max. 10/50 Volts Volts Volts Volts Volts mA °C MHz/% CrosstalklD 10KHz (20 Vpp) 1 MHz (20 Vpp) 10 MHz (5 Vpp) 20 MHz (3 Vpp) Chan. Input capacitance MIN. TYP. MAX. UNITS - -105 -94 -76 -64 -100 -92 -71 -62 dB dB dB dB - 4 10 6 12 pF pF - 8 10 pF +14.5 -14.5 +4.75 +15 -15 +5 +15.5 -15.5 +5.25 - 4.0 12 3.5 -80 3.0 10 3 -90 - 207 0 -55 -65 - - (Off) (On) Chan. output capacitance (On) POWER SUPPLY REQUIREMENTS FUNCTIONAL SPECIFICATIONS Apply over the operating temperature range and at ±15V and +5V dc unless otherwise specified. ANALOG INPUTS MIN. Analog signal range On resistance, +25 °C 010 +70·C -5510 +125·C RON versus VIN Input leakage current (Off), +25°C 010+70·C -55 to +125 °C Output leakage current (Off), +25 ·C 010 +70·C -5510 +125 °C On channel leakage current, +25 ·C 010 +70·C -5510 +125 °C Nonlinearity Large signal bandwidth (-3dB) - - - TYP. MAX. ±10.0 18 90 120 140 See Figure 1 - 0.02 - 0.02 - UNITS Volts Ohm Ohm Ohm 0.2 10 25 nA nA nA 0.2 20 40 nA nA nA - - - 1.0 25 35 0.001 80 100 - MHz 2.0 - - Volts Volts 0.4 nA nA nA %FSR DIGITAL INPUTS Logic Logic Logic Logic Levels "1" Levels "0" Loading "1" Loading "0" - - 0.8 1 -1 IlA IlA - - 20 nS - 3 10 10 nS nS - 25 40 60 80 30 50 70 100 nS nS nS nS - 25 40 60 80 30 50 70 100 nS nS nS nS - 30 50 75 100 35 60 85 120 nS nS nS nS 30 50 75 100 35 60 85 120 nS nS nS nS - Power supply range +15V -15V +5V Power supply current, quiescent +15V -15V +5V Power sup. rejection ratio Power supply dissipation, quiescent +25°C 010 +70·C -55\0 +125·C Pd versus frequency - - - Volts Volts Volts mA mA mA dB 260 260 280 see Figure 3 mW mW mW - °C ·C °C - PHYSICAUENVIRONMENTAL Operating temp. range -MC -MM Storage temp. range Package type -MC/MM Pin type -MCIMM Weight +70 +125 +150 14-pin hermelic DIP 0.010 x 0.Q18 inch Kovar 0.1 Oz. (3.5 grams) maximum ID See Figures 2a and 2b. SWITCHING CHARACTERISTICS Access time Break-belora-make delay time Enable delay (On, Off) Settling time, 10M Load (0.1%) 10Vslep (0.01%) 10V slep (0.003%) 10V slep (0.001%) 10V slep Settling time, 5K Load (0.1%) 10Vslep (0.01%) 10V slep (0.003%) 10V slep (0.001%) 10V slep Settling time, 10M Load (0.1%) 20V slep (0.01%) 20V slep (0.003%},20V slep (0.001%) 20V slep Settling time, 5K Load (0.1%) 20V slep (0.01%) 20V slep (0.003%) 20V slep (0.001%) 20V slep 6-16 - - - Table 1. Channel Addressing ON CHANNEL En Disable 1 2 3 4 1 0 0 0 0 MUXADDRESS A1 X 0 0 1 1 AO X 0 1 0 1 DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 0204S-11941TEL (508) 339-30001TLX 174388/FAX (508) 339-6356 ~~[b MX·850 120 110 +125°C 100 90 t\ cr -120 80 -100 70 60 -BC 50 -6C 40 30 -4C 20 -2C 10 -10 -8 -6 -4 -2 0 2 4 6 8 100 KHz 10 Inpu1 Vo~age 1 MHz 10 MHz 100 MHz INPUT FREQUENCY Figure 2a. Small Signal Crosstalk Versus Input Frequency Figure 1. Channel On Resistance Versus Input Voltage 1.5 ±1V J\J CH.1 OUTPUT 1.2 ~ CH.2 z CH.3 CH.4 MX-850 (Load of a X1 0 probe) ~a. r;; '"c 1.0 0.75W 0.7 0: w ~ a. 0.5 0.2 DC Figure 2b. Crosstalk Test Circuit 1 MHz 2 MHz 3 MHz 4 MHz 5 MHz 6 MHz 7 MHz a MHz 9 MHz 10 MHz SWITCHING FREQUENCY 50% DUTY CYCLE Figure 3. Power Dissipation Versus Switching Frequency For Immediate Assistance, Dial 1-800-233-2765 6-17 MX·850 +5V Current Limiting Resistors f~ As noted in Technical Note 3, some current limiting technique must be employed to protect the device. The following lists the suggested resistor values for the current limiting resistors shown in Figure 4. O.OlIiF 12 +5V 2 AO 3 A1 ANALOG INPUTS (±10V@ ±20 mA max.) Input Ranges Limiting Resistors ±10V ±5V R=500Q R=250Q No current limit needed EN LOGIC { CONTROL f~ R 5 CH1 ~1V MX-850 +15V +15V + y O . 0 1 IiF CH2 R 6 CH3 R """""Iv-----,7,-/ CH4 8 Other current limiting circuits can be used, such as a current limited op amp drive, depending upon the application. OUTPUT Figure 4. Typical Connections V' V'" 2 3 4 'V '\ 'V V' 7 8 'V IN1 IN2 IN3 IN4 IN1 IN2 IN3 IN4 MX-850 EN A1 5 OUT I--- AO MX-850 EN V 6 A1 OUT INPUT CHANNELS 1 - 8 OUTPUT AO -'"' (1) (2) (3) 3 -to-8 LINE DECODER Figure 5. Cascading Multiple MX-850's Channel Expansion The MX-850's ENABLE input provides a means of channel expansion. As shown in Figure 5 and in Table 2, multiple multiplexers may be used by connecting the ENABLE inputs to a decoder. ORDERING INFORMATION Table 2. Eight-Channel Addressing ON CHANNEL 1 2 3 4 5 6 7 8 6-18 MUXADDRESS 1 2 3 L L L L H H H H L L H H L L H H L H L H L H L H MODEL NUMBER MX-850MC MX-850MM OPERATING TEMP. RANGE SEAL Oto +70 °C -55 to +125 °C Hermetic Hermetic Receptacle for PC board mounting can be ordered through AMP Inc., Part # 3-331272-8 (Component Lead Socket), 14 required. For availability of MIL-STD-883B versions of the MX-850, contact DATEL. DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194fTEL (508) 339-3000fTLX 174388/FAX (508) 339-6356 OPERATIONAL AMPLIFIERS Model DC Open Loop Gain (VN) Settling Time (lisec) Slew Rate (V/liseC) Gain Bandwidth (MHz) Page Case AM-SOO 10· 200 nslO.01 % 1000 100 14-Pin DIP 7-3 AM-l43S 10' 70 nslO.01% 300 1000 14-Pin DIP 7-1 INSTRUMENTATION AMPLIFIERS Model AM-5S1 Gain Range Settling Time Case 1 to 1000 2 ~slO.01% 16-Pin DIP Page 7-5 RESISTOR TUNEABLE OSCILLATORS f'requency Range Accuracy Case Page ROJ·20 20 Hz to 20 KHz 0.5%@1 KHz 24-pin DIP 7-7 ROJ·1K 1KHz to 100 KHz 0.5%@10KHz 24-pin DIP 7-7 Model For Immediate Assistance, Dial 1·800·233·2765 7·i Contact DATEL for your Data Acquisition component needs. Dial 1-800-233-2765 for Applications Assistance 7-ii DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048~11!!14fTEL (508) 339-3000rrLX 174388/FAX (508) 339.-6356 AM-1435 Ultra-High Speed Wideband Operational Amplifier FEATURES 70 Nanoseconds settling to 0.01 % . • 1 GHz Gain bandwidth product 100 dB Open loop gain • 80 dB Minimum CMRR • -55°C to +125°C Operation GENERAL DESCRIPTION DATEL's AM-1435 is an ultrafast settling, wide-band operational amplifier. Utilizing precision thin-film hybrid construction and differential input operational amplifier design techniques, the AM-1435 achieves a settling. time of only 70 nanoseconds for a 10 volt step to 0.01% accuracy. High speed performance is optimized with high open-loop gain, flat frequency response beyond 10KHz and a roll-off of 6 dB/octave to beyond 100 MHz. Typically, gain bandwidth product is 1 GHz and slew rate is 300 V/ microsecond. MECHANICAL DIMENSIONS INCHES (MM) ..-LR . I- 0.500 MAX'--l - I~ (12,7) ---r-- '-. 0.010 x 0.018 KOVAR 17 AM-1435 dc characteristics include a dc open loop gain of 100 db, 1 Mil input impedance, and an initial input offset voltage of only ±2 mV. Input offset voltage drift is typically ±5 IlV/oC. Also featured is a minimum common mode rejection ratio of 80 dB and full power frequency of 8 MHz. 8' 0.700 I I I BOTTOM I 6 SPACES AT o(~~ EA. , I DOT ON TOP REFERENCES PIN 1 190(".)MAX. -r- 0.150 MIN. (3,8) I 1 VIEW I 0.800 MAX. (2"') I I 141 l 0.100 __ • _0.100 1 (2,5) NOTE: PINS HAVE 0.025 ±O.01 INCH STANDOFF FROM CASE +15V OFFSET AOJlJST INPUT/OUTPUT CONNECTIONS PIN 1 2 -IN 3 4 5 AM-1435 OUTPUT CURRENT SOURCE COMMON +IN 6 7 8 9 10 11 12 13 14 FUNCTION OPTIONAL CAP OUTPUT COMPENSATION CAP. +15VSUPPLY +vs OFFSET ADJUST OFFSET ADJUST - INPUT + INPUT N.C. N.C. N.C. Vs 15VSUPPLY OUTPUT CURRENT SOURCE COMMON .. 1 -15V OPT COMP CAP CAP For Immediate Assistance, Dial 1-800-233-2765 7-1 AM·1435 FUNCTIONAL SPECIFICATIONS at + 25·C, ± 15V de SUpplies, unless otherwise noted. TECHNICAL NOTES Typical INPUT CHARACTERISTICS MINIMUM - TYPICAL MAXIMUM - ±4V Differential between Inputs •••••••••••• Common Mode Voltage Range ••••••.•• Common Mode ReJection Ratio; ±7V ±8.5V de .............................. 80 dB 1 MHz ........................... Input Impedance; common mode ................... differential mode .................. Input Offset Voltage" ................ Input Bias Current ................... Input Offset Current ••••••••••••••••• 70 dB ±2mV lMO~2pF 2.5 kO ~ 2 pF - -- 2. When using the AM·1435MM over the +85 to + 125'C temperature range, use an 18'CIW heat sink. -- ±5 mV 20 !lA 10 !lA 0.3 !lA - OUTPUT CHARACTERISTICS Output Voltage" ••••••••••••••••••••• Out~ Current" ••••••••••••••••••••. Sta e Capacitive Load4 ...•••.....••• ±5V ±10mA ±7V ±14mA 1000 pF 90 dB 100 dB ±5'/,V/oC 50 nAl°C 2 nAloC - - - .................. .................. - ±25/,V/oC 100 nAl°C 15"V p.p 1.6 "V RMS 5.2 "V RMS 2.5 nA p.p 2.5 nA RMS 3.5 nA RMS 0.15 mVN AVs - 700 MHz - 8MHz -- .......................... 250 V/"sec.' - 1000 MHz 150 MHz 10 MHz 60 nsec. 70 nsec." 25 nsec. 40 nsec. 10 nsec. 20 nsec. 300 VI"sec. - 5 nsec. 40 nsec. 50 nsec. .- The 2 pF compensation capacitor at Cl is required for stable operation when the noise gain is less than 10. Compensation for bias current is provided by R2 and its value determined by the formula R2= (Rl) X (R4) Rl + R4 R3 and C4 are optional. Use C4 when driving capacitive loads to prevent oscillation of the output stage. .DYNAMIC CHARACTERISTICS Gain Bandwidth Ilmduct •••••••••••••• URity Gain BandWidth •••••••••• : ••••• Full Power Frequency" •••.•••••••••.• SetUingTime,10VtoO.025%7 ••••.•••• 10VtoO.01% ••••••.•••• 5Vto1.0% ............. 5VtoO.1% ............. 1Vto1.0% ............. 1VtoO.1% ••••••••••••• Slew Rate Overshoot ......................... Proparmtion Delay .................. RISlrT me, 10V Step ................. OverIaad Recovery Time .•••••••••••• 3. Apply negative supply voltage before the posi· tive supply. Power·up prior to applying power to either input. If frequency response is not critical, use an external input protection circuit. COMPENSATION· The typical connection diagram shows the AM'1435 in a unity gain inverting configuration. Use in any conventional amp circuit, the AM·1435. as a noninverting amplilier, requires a noise gain of at least two (NOISE GAIN = 1 + R4IR1). - PERFORMANCE de Open Loop Gain" ................. Input Offset Voltage Drift ............. Input Bias Current Drift ••••.•••••••••• Input Offset Current Drift ••••••••••••• Input Voltage Noise, 0~01 Hz to 10 Hz ................... 100 Hz to 10 kHz 10 Hz to 1 MHz .................... Input Current Noise", 0.01 Hz to 10 Hz ................... 100 Hz to 10 kHz 10Hzto1 MHz .................... Power Supply Rejection Ratio ••••••••• 1. The extensive use 01 a ground plane for all common connections is recommended. Keep lead length to a minimum with point·to·point connections wired directly to the amplifier pins. Use 1 ~F tantalum bypass capacitors the +Vs and ·Vs pins. -75 nsec. When using the AM·1435 at low impedances, include the feedback resistor as a part of the total output load. -- 60 nsec. - 1% - TYPICAL CONNECTION DIAGRAM +15V R4 ·POWER REQUIREMENTS Rated Supply Voltage ................ Quiescent Current- •••••••••••••••••• ±12V - ±15V - ±16V ±30mA 2 pF PHYSICALIENVIRONMENTAL Rl Opar. Temp. Range AM·1435MC AM·I435MM9IMM·QL Storage Temp. Range Package INPUT 1 kG oto +70 °C ·55 to +125 °C ·65to+125°C 14·pin hermetically sealed ceramic DIP ORDERING INFORMATION . FOOTNOTES: I. Specified for de linear operation. Common mode' voltage range prior to fautt condition is ± 10V de maximum. 2. Adjustable to zero. 6. C, = 0.5 pF. 3. f\ = SOOQ. 7. C, = 1 pF. 4.C, = 3 pF. 8. ±Vs = ±15V dc. 5. Referred to input. 9. Wfth 18"C1watt heat sink. 7·2 Model No. Operating Temp. Range AM·1435MC AM·1435MM AM~ 1435MM·QL Oto +70 °C ·55 to +125 °C ·55 to +125 °C ~C3 1"F -15V DATEL, Inc. 11 Cabot Boulevard. Mansfield. MA 02048·1194ITEL (508) 339·30001TLX 174388/FAX (508) 339·6356 AM-500 Series Ultra-Fast Operational Amplifier FEATURES • 200 Nanoseconds settling to 0.01% • 1000V/Microsecond slew rate • 100 MHz Minimum gain-bandwidth 106 Open loop gain 1 Microvolt/oC drift ± 50 mA Output current -LR I-- 0.500 MAX,-!'~ (12.7) GENERAL DESCRIPTION a.15OMIN. (3,8) The AM-500 Series amplifiers are ultra-fast settling operational amplifiers for use in inverting applications. A unique feedforward amplifier design combines the characteristics of a low drift dc amplifier with those of a very fast AC amplifier. For optimum fast settling performance, this amplifier has an open loop gain roll-off of 6 dB per octave to beyond 100 MHz. r- '0.010 II 0.018 KOVAR 81 1 17 1 MECHANICAL DIMENSIONS INCHES (MM) AM-500 series dc characteristics include a dc open loop gain of 106 , 30 megohm input impedance, and 1 nanoampere bias current. Input offset voltage is ±0.5 mV and input offset voltage drift is 1 microvolVoC. Although these amplifiers do not operate differentially, a dc offset voltage in the range of ±5V dc can be applied to the positive input terminal. Power supply requirement is ±15V dc at 22 mA quiescent current. The amplifiers will operate over a supply range of ±10V to ±18V dc. Output current capability is ±50 mA with output short circuit protection. 0.700 6 SPACES AT 0.100 EA. I BonOM I I VIEW (2,5) I 0.805 MAX. (20,3) REFERENCES PIN 1 ~ I DOT ON TOP Output settling time is 200 nanoseconds maximum to 0.01 % for a 10 dc volt step change. Slew rate is 1000v/ microsecond for positive output transitions and 1800V/ microsecond for negative transitions. This high slew rate permits undistorted reproduction of a full load, 20V peak-topeak sinewave out to 16 MHz. Gain bandwidth product is 100 MHz minimum. 0.190 (4.B) MAX. ~ 4--+-! 0.100 0 1~~2~~ NOTE: PINS HAVE ±O.Ol INCH STANDOFF FROM CASE IZ IOOnA w ,/ a: a: :::> CJ en < in t-- r-q::7 I- :::> a.. Z -lOOp,," ,cuiRENT -" (,~\LES TYPe '"' - EVERY lOGe I \J -CU~rNT TEMPERATURE INPUT/OUTPUT CONNECTIONS PIN NC NC NC -IN + IN NC 1 2 3 4 5 6 7 8 9 NC NC NC OUT 00 .coM. NCT CONNECT For Immediate Assistance, Dial 1-800-233-2765 10 11 12 13 14 FUNCTION NO CONNECTION NO CONNECTION NO CONNECTION -INPUT +INPUT -SUPPLY NO CONNECTION COMMON DO NOT CONNECT OUTPUT +SUPPLY NO CONNECTION NO CONNECTION NO CONNECTION 7-3 AM·SOO Series 1 FUNCTIONAL SPECIFICATIONS, AM-SOO SERIES Typical at 25·C, ± 15V de supply, unless otherwise noted. INPUT CHARACTERISTICS Input Common Mode Voltage Range· •••••••••.•.•.•.••••••• ±5V Maximum Input Voltage, no damage ••••••••••••••.••••••• ± 18V Diflerentiallnput Impedance .•••••• 30 Meg. typical, 3 Meg. min. Input Bias Current •••••••••••.•.•• 1 nA typical, 4 nA max. Input Offset Current •••••.•.•.•••• 0.5 nA typ., 8 nA max. InputOflsetVoltage •••..••••••••. 0.5 mV typ., 3 mV max. OUTPUT CHARACTERISTICS Output Voltage .................. ± 10V min. Output Current, S.C. protected •.••• ± 50 rnA typ., ± 25 rnA min. Stable Capacitive Load .•.••••..••• 100 pF Output Impedance •.•.•.•.•••..•• 250 PERFORMANCE DC Open Loop Gain ..••••••••...• Input Offset VOlta?:e Drift, O·C to + 70· •••••••••••.•• -55·Cto + 125·C •••••••••••.• Input Bias Current Drift, -55·Cto +70·C •.•.•.•.•...•. +70·Cto +12S·C ..••••••••.•• Input Voltage Noise," 0.01 Hz to 1 Hz •.......•..•.•••. 10· volts/volt 1 ,"v/oe typ., 5 ,"v/oe max. 5 ,"v/oe typ., 10 ,"v/oe max. -20 pAloe doubles every 10·e 5 '"v peak-to-peak typ., 25 ,"V peak-to-peak max. 100Hzt010kHz •..••.•.•••••.• 1 ,"V RMStyp., 5 ,"V max. 1 Hz to 10 MHz .•.•..••••.•..... 20 ,"V RMS typ., 100 ,"V max. .Power Supply Rejection Ratio •. , .•. 80 dB min. DYNAMIC CHARACTERISTICS Gain Bandwidth Product ••...••.... 130 MHz typ., 100 MHz min. Slaw Rate, positive going .•..•••••• 1000VI t"69c. Slew Rate, negative going •.••••••• 1800V/,"sec. Full Power Frequency (20V peak-ta-peak) •.•••••.•.••••• 16 MHz Settling TIme, •..••••••••. 70 nsec. 10V step to 1%3 10VsteptoO.1%3 •.•...•.•.•.•. 100 nsec. 10V step to 0.01%" .•.•.•...•••. 200 nsec. max. Overload Recovery Time •.....•.•. 10 t"69c. TECHNICAL NOTES 1. The circuit design shows the connection of the AM-500 series for fast settling operation with a closed loop gain of - 1. It can be used for fast settling at closed loop gains up to -10. The equivalent resistance seen by the summing junction should be 500 ohms or less. For gains larger than - 1 use an input resistor of 500 ohms and pick a feedback resistor for the required closed loop gain (1 k for - 2, 1.5k for - 3, etc.). 2. A small feedback capacitor should be used across the feedback resistor. Determine C in nanofarads from the following formula: C = 1 + IGI 0.816Rf where G is closed loop gain and Rf is in kilohms. 3. Summing pOint leads must be kept as short as possible. Input and feedback resistors should be soldered close to the body of the resistor directly to the summing pOint (pin 4). Summing point capacitance to ground must be kept very low. 4. Low output impedance power supplies should be used with 1 p.F tantalum bypassing capacitors at the amplifier supply terminals. There are internal 0.03 p.F ceramic capacitors in the amplifier. 5. Although these amplifiers are inverting mode only, a dc voltage in the range of ± 5V may be applied to the positive input terminal for offsetting the amplifier. 6. For interrupted power applications, apply power to the AM-500 three (3) seconds before operating the device. CONNECTION FOR FAST SETTLING WITH GAIN OF-1 +1!iVdc: 2.4pF KEEP THESE LEADS AS SHORT AS POSSIBLE 1 /IF TANTAlUM INPUT ()---"\i\I\I''''''''''-! ">''''''-0 OUTPUT POWER REQUIREMENTS Voltage, rated pertonnance .•.••••• ± 15V dc Voltage, operating •.•.•.•.••••.•• ± 10V dc to ± 18V dc Quiescent Current •...•••••••••... 22 mA typ., 33 mA max. -11i1/de -15V -;;:' PHYSICAUENVIRONMENTAL Operating Temperature Range AM-SOOGC .....•...•.•.•..•••• ooe to + 70°C AM-500MC •.•.••••..•.••••••.. ooe to + 70·e AM-SOOIMM/MM-QL .••..••••••..• -55·e to + 125°C Storage Temperature Range ••••••• -55·e to + 125°C Package Type ••...•••.•.•••.••.• 14 pin ceramic Pins •.•.•••.•.•...••.•.•.•.•.•. 0.010xO.Ole" Kovar Weight ..•.•.•.•...•..•••.•.•.•. 0.09 ounces (2.5 grams) FOOTNOTES: 1. de only 2. - 3 dB Single.pole bandwidth 3. lk Input and feedback resistors, 2.4 pF feedback capacitor 7-4 ORDERING INFORMATION MODEL NO. OPERATING TEMP. RANGE SEAL AM-500GC AM-500MC AM-500MM AM-500MM-QL Oto +70 °C Oto+70°C -55 to +125·C -55 to +125·C Epoxy Herm. Herm. Herm. DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194fTEL (508) 339-3000fTLX 174388/FAX (508) 339-6356 AM-551 Low Cost, Programmable Gain Instrumentation Amplifier FEATURES 1 to 1000 Gain range ±O.01% Maximum nonlinearity • 2 Microseconds settling time • 100dBCMRR GENERAL DESCRIPTION MECHANICAL DIMENSIONS INCHES (MM) DATEL's AM-551 is a low cost, high performance, programmable gain instrumentation amplifier manufactured with hybrid thin-film technology. Gain is adjustable over a range of 1 to 1000 by the addition of a single external resistor and a simple user-selectable pin-strapping option. Maximum gain nonlinearity is ±O.01%. b-Pio~t ---9-1'1 T ~:==:::======~IT 0.300 The AM-551 dynamic characteristics include a settling time of 2 microseconds for a 20V dc output step to 0.01 % accuracy. Slew rate is 23V dc/microsecond and small signal bandwidth is 400 KHz. Other specifications include a common mode rejection ration of 100 dB, a 10 '20 input impedance and a minimum output voltage swing of ±11 V dc. Maximum offset voltage drift is ±15 microvolts/oe. 0.310 17,61 17,91 ...L PIN 1 -.l IOENT. ~mwm~'" '" ~'7"." T 0095 The combination of high accuracy, speed, low cost, and rugged hybrid construction make the AM-551 and ideal choice for applications involving the remote amplification of low-level signals produced by thermocouples, strain gages and RTD's, high performance data acquisition systems and remote instrumentation systems. ---I I.- 0 100 . -1 L . 0.01. I I t2.51 I I fO.461 16·PIN CERAMIC DIP Power requirement is ± 15V dc and all devices are cased in miniature, hermetically sealed, 16-pin ceramic packages. Models are available for operation over the commerCial, ooe to + 70 oe, and military, -55°e to + 125°e operating temperature ranges. PIN 1 INPUT OFFSET ADJUST .Vs 14 ~ 9~ OUTPUT OFFSET ADJUST >--~'V\I'v-""'--,\Mr-------!D7 SIGNAL COMMON For Immediate Assistance, Dial 1-800-233-2765 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 FUNCTION INPUT OFFSET ADJUST RG (Gain Resistor) + INPUT RG-.iGain AesistoQ - INPUT -VS SIGNAL COMMON OUTPUT OFFSET ADJ. WIPER OUTPUT OFFSET ADJUST OUTPUT OFFSET ADJUST OUTPUT OUTPUT GAIN SELECT GUARD +VS INPUT OFFSET ADJUST INPUT OFFSET ADJ. WIPER 7-5 AM·551 TECHNICAL NOTES ABSOLUTE MAXIMUM RATINGS Positive Supply, Pin 14 .•••.••••••••••. Negative Supply, Pin 6 ............... . Input Voltage Range ••••••••••••••••.• DIfferential Input Voltage Range •••.•..• Output Short Circuit .••••••.•••••.••.• Power Dissipation •............•.••••• +18V -18V ±18V ±30V Continuous 810mW FUNCTIONAL SPECIFICATIONS Typical at +25 oC, ±15V dc supplies, unless otherwise noted. INPUT CHARACTERISTICS Input Offset Voltage, unadjusted1, max. Input Bias Current, max. Input Offset Current, max. Input Impedance, Dill. or Com. Mode Common Mode Voltage Range, min. ±1 mV xgain ±100 pA ±20pA 10120 ±11V 1. A 25 kG trimpet may be used for both input and output offset adjusts. The trimpet is connected across the input offset adjust pins (Pins 1,15) and the wiper is connected to Pin 16. For output offset adjust, the trimpet is connected across the output offset adjust pins (Pins 10, 9) with the wiper connected to Pin S. 2. For unity gain, RG is left open and the output gain select pin (Pin 12) is tied to the output pin (Pin 11). To avoid oscillation in the unity gain configuration, the connection between the output gain select pin and the output pin should be kept as short as possible. 3. Gain selection is accomplished in two stages. The input stage gain (G 1) is selected by an external gain resistor (RG) connected across the (RG) pins, (Pins 2, 4) and is expressed as follows: OUTPUT CHARACHTERISTICS G1 =1 + 20k ±IIV :t5mA 0.50 ±1 mV xgain RG The output stage gain (G:v is selected by external pinstrapping: For G 2 = 1, connect the gain select pin (Pin 12) to the output pin (Pin 11). For G 2 = 10, connect the gain select pin (Pin 12) to the signal common pin (Pin 7). Gain Range4 Gain Equation7 Gain Accuracy, max. Gain Nonlinearity, max. Gain Tempco, max.s Offset Voltage Drift, max. Input Bias Current Drift Input Voltage Noise, dc to 100 Hz Power Supply Rejection Ratio Common Mode Rejection RatioS 1 KHz 100 Hz dc Slew Rate Small Signal Response, (-3 dB) G= 1,10 G=50 G= 100 G = 1000 Settling Time, 20V to 0.01% G=1 G= 10 G=50 G = 100 G = 1000 POWER REQUIREMENTS 1 to l000VN G = (1 + 20klRG)G2 ±O.04% ±O.OI% 50 ppm/"C The total gain of the amplifier is as follows: Rated Power Supply Voltage Supply Current, max. Power Supply Range ±15V dc ±27 mA :t5Vto±18V Output Voltage Range, min. (RL =2kO Output Current, min. Output Impedance3 Output Offset Voltage, unadjusted!, max. PERFORMANCE 15!1V/"C Doubles for every 10 "C 20 nVl-YHz 82 dB Gt 3.0 IJ5 4.0 IJ5 lllJ5 20 IJ5 200 IJ5 (1 + ~:) G 2 4. Both power supplies should be bypassed to ground with 0.1 microfarad electrolytic capacitors. TYPICAL CONNECTION DIAGRAM 96 dB 98 dB 100 dB 23V11J5 600 KHz 200 KHz 100 KHz 40 KHz = G1 X'G 2 = +15V 14 (-) Input (+) Input 5 3 .::>r.,,---o Output Ro PHYSICAL/ENVIRONMENTAL Operating Tempenature Range MC MM Storage Temperature Range Package Type Oto+70"C -55 to +125 "C -65to+150"C 16 pin Ceramic DIP Footnotes: 1. Adjustable to zero. 3. At 1 KHz, for all gain ranges. 4. To 0.01 % accuracy. Higher gains degrade pertormance 5. Tempeo of % = ±O ppm! "C. For RG =~, Gain Tempeo = 5 ppm/ "C 6. 1 kO Source Imbalance 7. G2is the gain of the second stage of the AM-551. Connecting output gain select (pin 12) to the output (pin 11) sets the second stage gain at 1. Connecting output gain select (pin 12) to signal common (pin 7) sets the second stage gain at 10. RG is the gain resistor for the first stage and is connected to RG (pins 2, 4). 7-6 Guard Drive •• See Technical note #3 ORDERING INFORMATION MODEL NO. OPERATING TEMP. RANGE AM-551MC AM-551MM Oto+70 °C -55 to +125 °C DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 0204S-1194fTEL (50S) 339-3000ITLX 1743SS/FAX (50S) 339-6356 ROJ-20,1K Resistor Tuneable Oscillator MECHANICAL DIMENSIONS INCHES (mm) FEATURES • Oscillation frequency is set by two external resistors • Ultra low distortion: 0.0018% typical • Stable • Hybrid, small 1-----1.36(34.5)1-----1 PIN SECTION 0.02XO.OI (O.5xO.25) GENERAL DESCRIPTION r- ROJ-20 and ROJ-1 K are resistor tuneable oscillators whose oscillation frequency is set with two external resistors. Output frequency range of ROJ-20 is 20Hz to 20KHz while that of ROJ-1 K is 1KHz to 100KHz. Output distortion is as low as 0.0018% typical at 1KHz frequency range. Output voltage temperature coefficiency is also as low as SOppm/oC. Output voltage amplitude is internally trimmed at 2.SVrms ±O.S% and this amplitude is adjusted to the range from SOOmV to 20Vp-p with external resistors. Sine and cosine waves are generated from two output terminals. A synchronization input terminal is provided in order to fine tune the relationship of these two outputs. 0 . 72 (18.2)-j ~R 0.31 --l 0'2~8~~ ~ !-0.60(15.2H 0.74(18.7) !-0.IO(2.54) PHASE DIFFERENCE BElWEEN SYNC INPUT AND OUTPUT (Fig. 6) (Technical NoteS) 180·1tC:::--...,-;-;;:-:.......- -...- - . " Hybrid construction has made it possible to build highly stable oscillators in small size at low cost. i 150' t-+-'Ic---t'\-' ~ 120' r+-~~~~rr---r--~ 8£ ~ 0 ~~ RElIT f ..... 9O·1-t---t---""I~--t---H H 6O'1+--t--Th:-1~--H 1'5 , ..... a. III 30"1-t---t----1'--t---\-t--"""H RUT 0"~0~,~~~~0~.9=5~~~~~~--~1.~10~ 11 Outputl t. fin: Sync Input Frequency fo: Frequency when no Sync In is given. PIN CONNECTIONS PIN 1 3 5 7 ,........ -ISV)--..... ORDERING INFORMATION --_...J I~l~----- ---- - _,, I MODEL NO. DESCRIPTION FLJ-ACOl Oscillator adapter for FW-D Series filters fe Set Logic Input Nolet. OpenSW1 and SW2 for 2.5VnnS output. ClcasSW1 and 2. Two Cext are required fer RJ..OC. 8-2 ~for 2OVp-p output. DATEL, Inc. 11 Cabot Boulevard, Mansfield. MA 02048-1194ITEL (508) 339-3000ITLX 174388/FAX (508) 339-6356 FLJ-ACR1, 2 Logic Controlled Resistor Network MECHANICAL DIMENSIONS (Fig. 2) FEATURES INCHES(mm) • Cutoff frequency of resistor tuneable filters can be set with BCD logic. • Single Inline hybrid. • Small size, low cost PIN SEOTION O.02xO.OI (O.SXO.25) ATnTn2T'0"3(m51~'5n)Tn~ ~~ ~ GENERAL DESCRIPTION __ FLJ-ACR series are logic controlled resistor networks. They are designed to be used with resistor tuneable filters such as FLJ-UR series. 0.05(1.2) Four separate resistor networks are included in one package. One network consists of four resistors such as R, R/2, R/4 and Rl8. The value of R in FLJ-ACR1 is 1.59MQ while that of FLJ-ACR2 is 150kQ. FLJ-UR Series List A combination of an FLJ-ACR and an FLJ-UR makes it possible to make a filter whose cutoff frequency or center frequency is set with BCD logic. It is also possible to use this resistor network in the negative feedback loop of an amplifier circuit and control the gain with BCD logic. Model No. FLJ-UR4LA1 FLJ-UR4LB1 FLJ-UR4HA1 FLJ-UR4HB1 FLJ-UR2LH1 FLJ-UR1BA1 FLJ-UR2BA1 FLJ-UR2EA1 FLJ-UR4LA2 FLJ-UR4LB2 FLJ-UR4HA2 FLJ-UR4HB2 FLJ-UR2LH2 FLJ-UR1BA2 FLJ-UR2BA2 FLJ-UR2EA2 LP: Lowpass HP: Highpass B p: Bandpass Logic Input Ie Range 40Hz 1.6KHz 400Hz 20KHz No.olPole 4 4 4 4 2 1 pair 2 pair 2 pair 4 4 4 4 2 1 pair 2 pair 2 pair Type LP. Butt. LP, Cheb. HP Butt. HP. Cheb. LP/HR,Butt. BP, Butt. BP. Butt. BE, Butt. LP, Butt. LP, Cheb. HP. Butt. HP, Cheb. LP/HP.Butt. BP. Butt. BP, Butt. BE. Butt. BE: Band elimination Butt.: Butterworth Cheb.: Chebychev logic Input GND +l5V -15V R=1.59MQ(FU-ACR1) R= 159k.Q(FU-ACR2) For Immediate Assistance, Dial 1-800-233-2765 8-3 FLJ-ACR1, 2 SPECIFICATIONS Typical at 25°C, ±15VDC power supplies unless otherwise specified. ABSOLUTE RATINGS Power Supply Voltage (±Vs) •.•••••••••••.•....••.•.••...••.•.••.•• ±18V Input Signal Voltage •••...•.•••.•.••.•••••.••••.•••••••••..•••.••• ±Vs Control Logic Voltage .....••.•••.••.•••••..•.•..••• +5.5Vmax., -0.5V min. FREQUENCY SET MODE BCD 1 Digit. •• ••. • • . . .••• . • •. •. ••. .•.••. .. . . .•. .•••• . . ••. .••.. 0 to 15 BCD 1 Digit +1 •• ; ••.•••.•..•.•.••.•••••.....•..•••.•..•.••••.• 1 to 16 Table 1. Frequency Set Range (with FLJ-UR) Unit: Hz 1a. FW-ACR1 or ACR2 Single Use FLJ-UR Suffix Frequency Set Mode From FLJ-ACRl To Resolution From FLJ-ACR2 To Resolution -1 (Low Range) BCD BCD+l O· 10 150 160 10 10 O· 100 1.5k 1.6k 100 100 -2 (High Range) BCD BCD+l O· 100 1.5k 1.6k 100 100 O· lk 15k 16k lk lk TECHNICAL NOTES 1. FW-ACRl and FW-ARC2 contain four separate resistor networks which are controlled by common logic inputs. There are two types of FW-UR's (resistor tuneable filters) which are to be connected with FLJ-ACR's to build BCD Logic Programmable Filters. One type such as FWUR2LH or FW-URl BA requires two external resistors while all other FLJ-UR's require four external resistors to set a cutoff frequency. Therefore, one FW-ACR can control two FW-UR2LH's or FWURl BA's. See Figure 3. 2. BCD + 1 connections are made by connecting pins 6 to 8, 11 to 10, 13 to 15, and 18 to 17 on the units required per Table la. or lb. 1b. FLJ-ACR1 and ACR2 (Parallel Use) for Greater Frequency Resolution FLJ-UR Suffix Frequency I -ACR2 Set Mode I -ACRl ~- To Resolution -1 (Low Range) BCD+l BCD BCD+l BCD O· 10 100 1.59k 1.60k 1.69k 10 10 10 BCD BCD -2 (High Range) BCD BCD+l BCD+l BCD O· 100 lk 15.9k 16.0k 16.9k 100 100 100 BCD BCD • Output saturates at 11 V de with zero logic code input (0000); however, digital code correspons to value of fe directly. PERFORMANCE Frequency Set Error... . . .•••• •••. .•. .•. •. • ••. .•. .•••• . . ••.• ±1% or less CONTROL CHARACTERISTICS Logic Code ••••.••.••• BCD 1 digit (1, 2, 4, 8) Logic and Level •.••....•.•.••••.••.•..••••••.••.•.•••..•..••.. OV: ON +5V or Open: OFF POWER SUPPLIES AND ENVIRONMENT Power Supplyl(Operating Range) ••••••..•.••••••.•••.. ±15V (±5V to ±18V) Current ..•••..•.••.•..•••.••••.••••.•..•..•..•.•.•••. +6.2mA. -1.2mA Operating Temperature Range .•••.....•...••..•.•.••...••..•.• 0 to 70°C Storage Temperature Range .•.••••..•••.••.•••••.•••..•••• -30°C to BOoC Operating Humidity Range ..•.•••••.••.••.••.••••.••••.•• 10% to 95% RH Storage Temperature Range ••••.••••••.••.••.••••...••.•• 10% to 80% RH TYPICAL CONNECllON (Fig. 3) In,", -15V>-----t'~---+-+--1 ORDERING INFORMATION 8>---+-~-+~-------------1-+4-+-~~ 4>---+-~-+~---------------+-+-r+--4 '2 T MODEL RESISTANCE FW-ACRl FW-ACR2 1.59MO 159KO for FW-UR Filter Series 8-4 DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194ffEL (508) 339-3000ffLX 174388/FAX (508) 339-6356 FLJ-D1, D2, DC Digital-Programmable Filter FEATURES MECHANICAL DIMENSIONS INCHES(mm) • Cutoff frequency is set by logic inputs • Lowpass, Highpass and Bandpass output functions are available simultaneously • Gain and Q are set by external components • High accuracy, high stable Innmmm-II.; PIN SECTION 0.02 x O. 01 (0.5 x 0.25) GENERAL DESCRIPTION FLJ-D1, 02, and DC are digitally programmable filters which can set the cutoff frequency and center frequency with 3 digit BCD inputs. Two-pole lowpass, bandpass, and highpass output functions are available simultaneously from three different outputs and notch function is available by combining these outputs to the uncommitted op amp. To realize higher order filters, several filters can be cascaded. And to obtain higher performance of higher order filters, both Gain and Q are designed to be set with external components. --------------------1 r-2. 12 (53.9)----4 O.34~1 1.1.. ~.lI1J IIIIIIIIIII~IIIII 0.2(5.0) I' 0.1(2.54) 2.14(54.4) . ZENER OUTPUT (Fig. 3) +15V 1.431< 1I4W + 0.1J.1 4.7,1.1 - COM + 4.7,11_ - 0.1J.1 -lSV PIN CONNECTIONS (Table 1) j Feedback.ln BPlnput *C'.T AII1l.0ul LP, t-P BP '""'" . BOD 400 200 100 80 40 20 10 8 4 fcSet Logic Input FU-Ol SO,OOOpF FU-D2 SOOpF FU-IlC None. Need Cex!. 2 FUNCTION INPUT BP ANALOGGND INPUT HP. LP ANALOGGND OUTPUT HP ANALOGGND AMP. +) INPUT AMP. ) INPUT AMP. OUTPUT ANALOGGND Cex! 1. NC OUTPUT (BP) ZERO ADJ. HP. LP) NEG. FEEDBACK IN ANALOG GND Cex! 2. NC OUTPUT LP ZERO ADJ. BP PIN 1 40 2 39 3 3B 4 37 5 36 6 35 7 34 B 33 9 32 10 31 11 30 12 29 13 2B 14 27 15 26 16 25 17 24 18 23 19 22 20 21 FUNCTION +vs +15V 5V ZENER OUTPUT Vc(+5V) DIGITALGND ANALOGGND NC Ns -15V NC LOGIC BOO LOGIC 400 LOGIC 200 LOGIC 100 LOGIC BO LOGIC 40 LOGIC 20 LOGIC 10 LOGIC 8 LOGIC 4 LOGIC 2 LOGIC 1 DO NOT CONNECT NC PINS TO OTHERS. For Immediate Assistance, Dial 1-800-233-2765 8-5 FLd.D1, D2, DC SPECIFICATIONS (Table 2) Typical at 25 'C, ±15V and +5V supplies, gain of -1, Q = ,,[212 unless otherwise specified. ABSOLUTE RATINGS Power Supplies .•...•••• ±Vs : ±20V. Vc : +5.5V Control Logic Input ........ ,....... Vc+0.5V Analog Input ••.....•....•••...•.... ". ±Vs TECHNICAL NOTES 1. The cutoff frequency of low pass and highpass. and the center frequency of bandpass filters can be set with three digit BCD. TTL compatible logic inputs. The MSD is hexadecimal. See Table 2. 2. The cutoff frequency is shown as either one equation of the following: FILTER CHARACTERISTICS Frequency Program Range: FLJ-D1 ••• FLJ-02 ..• FLJ-DC •.. Frequency Program .....•.•••..• Frequency Program Accuracy Q Range .•.••. , •.••..•••..• , Rollof! ..................... Number of poles ............... Voltage Gain ................. Pass Band Gain Variance ......... Resonant Frequency T.C. ......... GainT.C. ................... Distortion ................... Noise ...................... Load Resistance ...•..••.•.... , •• 4 .... fc = 1Hz - 1.599KHz 100Hz -159.9KHz 0.1 Hz 10 159.9 KHz BCD 3 digits. 'MSD is hexa-decimal (0-15) ±O.1% 1/3~ Q~ 1 x 1(f Ifc 12dB/oct (LP, HP). 6dB/oct(BP) 2pole (1 pole pair) 1-10 Depends on external resistors 0.01%1'C 0.2dB Full Temperature Range 0.002% 35/1Vrms (LP). 100pVrms (HP), 30pVrms (BP) 2KO C = 50.000pF is contained in FLJ-D1 and C = 500pF is contained in FLJ-D2 respectively. while no capaCitor is contained in FLJ-DC. The fc's of each model are: N FLJ-D1 : fc = N or fc = 21T.5x10 ".Rf FLJ-D2: fc=100N orfc N FLJ-DC : fC=20'C or fc ±10Vmin. 3OOKO 0.5mV 200nA 5/lVrC ±10Vl5mA min. 50 max. 38mA 10MHz 8V1/lSec 3. 4. POWERSUPPLIES AND ENVIRONMENT Supply Voltages •..•..••...•.•• Supply Current ••......••..••.. Operating Temperature Range ...... Operating Humidity Range ........ Storage Temperature Range Storage Humidity Range ......•... ±Vs: ±15V ±10%. Vc: +5V ±10% +15mA. -18mA +2.2mA -2O'C - +70'C 10%-95%RH -30'C - +80'C 10%-8O%RH 5. S. 8-S C : pF. N : Digital fc = 21T'~'Rf Hz. C: F. Rf: n, N : Digital . Number AMPLIFIER CHARACTERISTICS Input Voltage Range ............ Input Impedance , ••....•••.•... Input Offset Voltage .......•.•... Input Bias Current .•••.• , •••••.• Input Offset Drift •.•.••.••••..•• Output Voltage/Current .......... Output Impedance ............. Output Short Circuit Current Small Signal Frequency Bandwidth SlewRate ................... 2~C Hz. Number N 21T'5x10 1O'Rf N 21T'Cext.Rf The value of Rf is 3.183 MO. The vaiueof Cext is calculated taking these factors into consideration. Each logic input is connected to CMOS4000 series internally. Then each input is pulled down with 100Kn resistors. The use of 10KO pull-up resistors to +5V is recommended when filters are programmed with TTL logic. An independent +5V zener diode is contained in the filter. The output voltage range of this diode is +4.87V +5.12V. The connection shown in Figure 3 is recommended if a filter is driven by ±15V supplies only. Analog GND (Pin3S) and logic GND (Pin37) are separated. Connect grounds of ±1SV and +SVexternally. No return current of the digital power supply should flow through the analog ground. The use of 4.7pF and 0.1pF bypass capacitors for both ±1SV and +5V lines close to the module is highly recommended. DATEL, Inc. 11 Cabot Boulevard, Mansfield. MA 02048-1194/TEL (S08) 339-3000/TLX 174388/FAX(508) 339-6356 FLJ·D1, D2, DC BUTrERWORTH HIGHPASS (Fig. 4) LOGIC INPUT CODING TABLE (Table 2) Logic Input·' (MSD) DODD DODD DODD DODD 0000 o 0 0 0 o 0 0 0 0000 000 I 00 I 0 o I 0 0 I 000 I 00 I I 0 I 0 I I 00 I I I 0 IIII IIII (LSD) o 0 0 0 o 0 0 0 DODD DODD 000 I o 0 I 0 o I 0 0 I 0 0 0 000 0 0000 0000 o 0 0 0 o 0 0 0 0000 0000 0000 DODD I DO I o 0 0 I o 0 I 0 o I 0 0 I 000 0000 o 000 o 0 0 0 0000 0000 0000 0000 0000 0000 0000 0000 0000 DODD I DO I 'n i'iI Ic (Cutoff Frequency) Devimal Number FLorDI FLorD2 I 2 4 8 10 20 40 80 100 200 400 800 900 1000 1200 UOO 1500 1599 1Hz 2 4 8 10 20 40 80 100 200 400 800 900 1000 1200 1400 1500 1599Hz 100Hz 200 400 800 1KHz 2 4 8 10 20 40 80 90 100 120 140 ISO 159.9KHz O.IHz 0.2 0.4 0.8 I 2 4 8 10 20 40 80 90 100 120 140 ISO 159.9Hz - 10H+t+Hrlt---'-I"Amp=.-l7fIttt----;Yl-t-H-I'rtt----i-t--H 40 I J -30 Q i - 6OIHft-t-ttrtt--t-+-t+ttHt--t-rHitlt1:---t-ffi240 1/ -70 0.03 0.3 30 10 280 (f/fe) BUTrERWORTH LOWPASS (Fig.S) T i -5 H- 'I 11 o , ii o JJ ! 1 0.03 11 40 NAmp· 80 1 i i II "'- I 20 PhaseI' I 60 I I -60 -7 I'11 I i I -30 J r-- 1 _ -20 -40 Q: .:-.: t 60 -5io/-++-1+I+tt-+-H-H+Ht-....,H-Hffitt--t--t-t-1200 0 1. Lowpass and highpass filters -1 10" (Rg: 0) Gain: G ='R9x :::-Q' 120 II V -40 -I 0 GAIN AND Q The gain and Q of·these filters are set with the following equations. L l ' j++tl--+/-¥-++tffiif'PhaseH-ffittt--H-H 80 i[ -20H-+-i-+ NoIe:*1.l.ogicl - HN logic 0 = GNDaOPEN "2.1FW-DC needs external capacitors. nae values we ones when two O.5pFare '*'CI as -- ttittb ___...-rt1tttttt:==!=-H1 !' FLorDC" 0.1 0.3 Rg'(Rq+10") Rq'(2Rg+10") '"1\ II II zoo !J t T r &: 240 280 10 (f/fe) 10" Rg =.10KO when G = -1. Then, Rq = 3Q-1 BANDPASS (Fig.S) Then, the following values are obtained: ~ _Q- Butterworth 0.70711 8.918KO Bessel .0.57735 13.66KO See Figures 4 and 5 for "Amplitude/Phase vs. Frequency" characteristics, and Figure 7 for typical connections. 0 -I 0 k" 1-"y Vv -20 2. Bandpass filter Gain: Q: G =...:.!.x Rg 10" (Rg'. 0) Q 01/ H(1/Rg+1IRq)'10" 2 V -60 ~ 10" Rg = 10KO when G = -1. Then, Rq = 2(Q-1) Then, the following values are obtained: _Q_ -so V' ...-BL -1 '/ J,Y ~\ 1"-1' 1\\1" Vv ~ V o~ V n03 ~rI~'" 1 0-2 10 - o-~I' lOtI' 1),_ ,.. t'--.- i' Q;.1~i' .. r0.1 0.3 10 30 (f/fe) 2 5.00KO 5 1.25KO 5560 10 See Figure 6 for amplitude vs. frequency characteristics and Figure 8 for typical connections. For Immediate ASSistance, Dial 1-800-233-2765 8·7 FLJ·D1, D2, DC LOWPASS & HIGHPASS CONNECTIONS (Fig. 7) HP Output LP Output 10K I}--T""'r---;" + 15V )-.-+--1--;,. COM H-.......-~~-15V I)-t--r- ---~ -15V H-"?"""1r--.... +5V .)-<'--+--<>---.... GNO ORDERING INFORMATION fo Set L;gic Input 8-8 MODEL OUTPUTfc FLJ-Ol FLJ-02 FLJ-OC 1 Hz 10 1.599 KHz 100 Hz 10159.9 KHz 0.1 Hz 10 159.9 KHz DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194ffEL (508) 339-3000ffLX 174388/FAX (508) 339-6356 FLJ-05,06 Digital-Programmable, High-Order Lowpass Filter FEATURES MECHANICAL DIMENSIONS inches (mm) • 60dB, aOdB/octave rolloff lowpass filter • Cutoff frequency programmed by logic at a points • Compact, lightweight, hybrid IC construction ~,- J)<-,-----' Pin Cross Section 0.009 x 0.009" (0.25 • O.25mm) Input • R FW-D5, and D6 series are lowpass filters that, although compact, have higher order and high attenuation performance. They are Chebyshev type filters. The FW-D5LA is a 5-pole filter which has a rolloff of 60 dB/oct and the FW-D6LA is a 6-pole filter with a rolloff of 80 dB/oct. The cutoff frequency is programmed with 3-bit, TTLcompatible digital logic and the settings can be changed to 8 different levels. Cutoff frequency range of the lower range type (which has suffix 1) is 10Hz-2kHz, and the higher range type (with suffix 2) is .100Hz-20KHz. Ripple within the pass band is minimal at 0.13dBp-p and the distortion rate is held extremely low at 0.05%. These filters are optimal as anti-aliasing filters in AID conversion circuits of data acquisition systems. 1 0. 0 l'_0.2 Ct Output FW-OSLA1,2 +1SV GNO ·15V Cf in the diagram is l0000pF lor the Suffix 1 model and l000pF forthe Suffix 2 model. Rext 1 Cut Rext2 Cext Rext 3 ~"f..r-~:-·~J~·i~-·,: Aexl4 Cext ~.y'~~':-·-i~-, • • -30 -'10 50 --- 1\ -0.4 0.1 Ct 20 !\ \ 0.2 R 10 I ~ R Ct ~t FW-DSLA1, 2 (Fig.4) ! Aexta RelCf2 r .....·/.. ·r~ 4~-,--"'".:V·T-·~t-l GENERAL DESCRIPTION -60 --..... I 1 10 Normalized frequency Inc FW-D6LA1, 2 (FIg.S) 70 ' II 100 "0 0 -10 iD ~ 10_2 "E < \ \ OV -20 -30 -'10 -50 -0.2 -60 -0.4 ·70 0.1 10 1 Normalized lnoquency Inc 100 For Immediate Assistance, Dial 1-800-233-2765 i '2 '1 FLJ-06LA 1, 2 Cf in the diagram is 1OOOOpF for. the Suffix 1 model and l000pF for the Suffix 2 model. 8-9 FL.J-D5, D6 SPECIFICATIONS (Table 1) Typical at 25°C and ±15V supply voltage unless otherwise specified. ABSOLUTE RATINGS Supply voltage (±Vs) •••••••••••••.•••••••••••••••••••••••••• ±16V Input voltage ••••••••••••••••••••••••.••••••••••••••••••• '•••• ±Vs Logic input voltage ••••.•••.•.••••••••••••••••• ~ • • • • • • • • • •• +5.5V FILTER CHARACTERISTICS, CUTOFF FREQUENCY Low Range (10. 20, 50, 100,200,500., lK, 2KHz, 8 points programmable, at -3dB) FLJ-DSLA 1 .............. _ 5-pole Chebyshev FLJ-D6LA 1 ............... 6-pole Chebyshev High Range (100,200,500, 1K, 2K, SK, 10K, 20KHz, 8 points programmable, at OdB) FLJ-DSLA2 _•.•.. ___ • . • • •• 5-pole Chebyshev FLJ-D6LA2 •••••• _• • • • • • •• 6-pole Chebyshev Setting of Cutoff Frequency •.. 3-bit binary, TTL-compatible Control Modell 10Hz 20 50 100 Modet2 100Hz 200 500 1KHz 200 500 51< lK 2K 10K 20K 2K lIIR T T 'T 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 0 1 1 1 1 0 0 0 1 1 0 "0": +SV or OPEN "1": OV 1 1 TECHNICAL NOTES 1. A switching-type power supply is not recommended. Install O.OII1F multilayer ceramic and 4.71!F tantalum bypass capacitors In parallel as close to the filter as possible. 2. Each logic input (Pins 21-24) which programs the cutoff frequency has an internal analog comparator as shown in Fig. 6. External logic Signals are TTL-compatible. 3. The fc setting input logic is negative true. Terminal open or +5V represents logic "0", while GND level is logic "1". The INH terminal is used normally open. OncelNH is given logic"I",ali4.2 and Tlogic inputs are inhibited and all internal resistor network switches are opened. The fc setting with external resistors becomes available with logic "1" at this INH terminal. The relationship between Ic and the external resistors in this case is as lollows: FLJ-05LAI (LOW Range Type) FLJ-DflJ.A1 (LOW Range Type) 31.423 x 10' (Kn) Ie 1Hz) Rextl : Rext2 29.622 x 10' (Kn) Ie (Hz) Rexl2: R.x13 21.399 x 10' (KO) Ie (Hz) Rex13: Rext4 18.633 x 10' Ie (Hz) Rex14: R.xt5 16.358 x 10' IKn) Ie (Hz) Rext5: Rexlti 15215 x 10' (Kn) Ie (Hz) Rexl1- 1 1 Accuracy of setting of cutoff frequency • _. ___ •••• _ ±3%max .. PASS BAND CHARACTERISTICS Gain OdB±0.3dBmax. (O.05fc) Ripple "_" .............. 0.13dBp-p (central designed value) Distortion rate 0.05% ROLLOFF CHARACTERISTICS FLJ-DSLA 1,2 FLJ-D6LA1,2 Rolloff . _••.. _. _•. , __ ... __ 6OdB/oct BOdB/oct Attenuation volume ••• _•••• _• 60dB (l,82fc) 74dB (t9fc) Minimum attenuation ........ 60dB 74dB Attenuation at lOfc-1MHz _.•. _• 55dBmin. 6OdBmin. INPUT CHARACTERISTICS Inputimpedance ..... _. _•.•• 5OKnmin. Maximum input voltage __ ••• _• ±10Vmin. OUTPUT CHARACTERISTICS Output impedance .•. _•. _•••. 100nmax. Maximum output voltage .. _•• __ ±10Vmin. Noise (input shorted) _••.••••. 140pVrms max. (BW10Hz-5OOKHz) Offset voltage .............. 10mV adjustable POWER SUPPLY AND ENVIRONMENTAL CONDITIONS Supply voltage •.•• _•••• _••• ±lSV ±1Vmax. Power consumption current • _•• ±28mA (FLJ-DS), ±33mA (FLJ-D6) Operating temperature/ Humidity range ••..... __ •••. -20oe to +70 oe, 10%-95%RH Storage temperature/ Humidity range ••••.••.•..•• -30 oe to +BOoe, 10%-80%RH .................... ............. FLJ-OSLA2 (High Range Type) Rexll 314.23 x 10' Ie 1Hz) (Kn) (Kn) FU-D6LA2 (High Range Type) Roxll: Rext2 296.22 X10' (Kn) Ie 1Hz! Rext2: R.x13- 213.99 x 10' IKn) Ic(Hz) Rext3 = Rext4 = 186,33 x 10' IKn) Ie (Hz) RexM : Raxt5 : 163.58 x 10' IKn) Ie (Hz) Rext5: Rexlti 152.15 x 10' IKn) Ie 1Hz) 4. An' l1-pole ultra-high attenuation filter is available once cascaded as shown in Fig. 7. As can be seen Irom the curves (Figs. 4,5), the amplitude 01 the ripple in the pass band is reversed between FLJ-05LA and FLJ-D6LA. As a result, when connected in a cascade, the pass band ripple amplitude is greatly reduced, and moreover, the rolloff becomes steeper. 5, For filters that have been constructed like those in this series, it is not recommended to change the Ic setting range with external capacitors. This is because trimming of the internal constants is performed with pairs 01 internal resistors and capacitors. Although shifting to a lower Ic setting range is possible through the addition 01 external capacitors, in this case a change will result in ripple amplitude. ORDERING INFORMATION LOGIC INPUT PINS (FIg- 6) CASCADE WIRING DIAGRAM (Fig. 7) Low Cutoff Frequency Type (10Hz-2KHz) FW-05LA1: 6OdS/oct.,5-pole FW-06LA1: 8OdS/oct.,6-pole ~I~--~---------/ (Pins 21-24) T "f -r High Cutoff Frequency Type (100Hz-20KHz) FW-05LA2 6OdS/oct., 5-pole FW-06LA2: 8OdS/oct., 6-pole 8-10 OATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-11941TEL (508) 339-30001TLX 1743881FAX (508) 339-6356 FLJ-R Series Higher Order, Resistor-Tuneable Filter FEATURES MECHANICAl DIMENSIONS • 135dB, 100dB/octave high order,lowpass filter ·113 octave bandwidth (Q=4.32) bandpass filter • can set cutoff (fc) frequency with 6 or 8 external resistors • Ultra-c:ompact size, high-function hybrid construction Inch.. (mm) Pin 1 Identification Pin Cross section. 0.009 • 0.001/" (0.25 • 0.25mm) GENERAL DESCRIPTION The FW-R series filters are of the highest order and have the highest attenuation characteristics among the entire group of DATEL filter products. Through the use of hybrid techniques, even though compact in size, the FLJ-R series filters have complete 8-pole lowpass and 3-pole pair bandpass filter functions. The cutoff (central) frequency can be set with only 6 or 8 external resistors. Inpc,lt RI S. CuI --!t- At 7' Cext Rt ··U-, Calif -n Rt Cext ",;-, Bandpass ripple in the lowpass filter is 0.1 dB and boasts outstanding performance with the distortion ratios for all models being a mere 0.005%. Each model is composed of the Suffix 1 and Suffix 2 types and varies according to cutoff frequency setting range. The Suffix 1 model has a range from 10Hz-2KHz and the Suffix 2 model has a range from 100Hz-20KHz. The FW-R series filters are optimum as antialiasing filters in AID conversion circuits of data acquisition systems. output The FW-R3BA 1, 2 are 1/3 octave, bandpass filters that meet IEC-225 Standard requirements. FW-R8LA, B Block Diagram with External Connections (Fig. 1) Input ~ Rf ~.1Il RI I AI • ~ t-.. -'1:'- 5 Cellt .;;. FlI Celli ·n·, 1. FW-R8LA1,2 +20 o -20 iii" :; 0.1 "C a -40 0 -60 -80 '6. E-0.1 -< -0.2 0.G1 I'll .::.- ci.ixt AI -;tJ c.xt +1511101<-15 OtfsetAdjustment FLJ-R3BA Block Diagram with External Connections (Fig. 2) -100 0.1 1 10 Normalized frequency fife 100 For Immediate Assistance, Dial 1-800-233-2765 8·11 FLJ·R Series SPECIFICATIONS Typical at 25° Cand ±15V supply voltage unless otherwise specified. ABSOLUTE RATINGS Supply voltage (±Vs) ••.•••••••••••••••••••••••.••••••••••••••••• ±18V Input voltage ••••••••••••••••.•••••••••••••••••••••••••••••••.•• ±Vs FILTER CHARACTERISTICS fc setting range ............ fc setting ••.•••••••••••••• fc setting accuracy ••••.•••.. Suffix 1: 10Hz-2KHz Suffix 2: 100Hz-20KHz B equivalent lowpass or 6 equivalent bandpass external resistors ±2%max. .................... ...... FlJ-RBLA B FW-R3BA OdB±O.ldBmax. OdB±ldBmax. OdB± - ................ Attenuation rolloff .••••.••••• 135dB/oct Attenuation volume ••..•••••. Minimum attenuation Attenuation at lOfc-1MHz .••••. 86d8@l.56fc 86dB BOdBmin. Suffix t model Cexl ·Same as left FLJ-R3BA - - 92d8@2.0fc l06dB 86dBmin. 4.32(BWl/30ct) 18dB/octBW - 8OdBmin. 100Qmax. ±10Vmin. 14lJiJVrms max. (BW10-SOOKHz) ± 10mV zero adjustable POWER SUPPLY AND ENVIRONMENTAL CONDITIONS Supply voltage (operating range) ±15V (±5V-±18V) Power consumption current 40mA (FLJ-RB) . 25mA (FlJ-R3) Operating temperaturel Humidity range •••.•••.••••• -lO°C to +70"C. 10%·95%RH Storage temperaturel Humidity range •••.••••••.•• -30°C to +80°C. 10%-80%RH .... FW-R3BA1,2 FW-RSLB1,2 r-TTrTtmr-nnTt1rm-TTnT111r>'"TT1mm 10 + 20 o ~~fflr+H~r+HffiOO-rHlliffiO H-++HfIIt--+tttlllll\-++ttlII~l-++lliffi - 20 10 - 10 ~ ~ 0.1 -++»~HH+mm-~~-40 ~-2O ~-30 1f-40 -60 - '" C. 0 ~-0.1 -80 -0.2 0.01 159 (Cexl +0.0011 x te (Kill In this case, the external capacitors should have high dielectric characteristics. It is recommended to use multilayerceramiccapacitors. Further, tolerance of these capacitors should be within ±0.25%. For filters such as these of higher order and with high attenuation characteristics, the uniformity of the tolerance of external resistors and capacitors has an effect not only on the accuracy of the setting range, but also on the size of pass band ripple. 2. Use series type power supplies for the ±15V power supplies because switching-type power supplies are not recommended. Install 4.7pF tantalum and 0.01pF multilayer ceramic bypass capacitors. It is recommended that these be installed in parallel, and as close to the filter as possible, between the ±15V power supplies and ground. 3. Use metal film resistors with a tolerance better than 1% for the 6 or S fc setting resistors. - 100dB/oct Inputimpedance ••.•••••..•• SOKOmin. Maximum input voltage ..•••.. ±10Vmin. OUTPUT CHARACTERISTICS 10 Suffix 2 model 159 (Cexl +0.011 x Ie (Kill Cexl where Cext is measured in p F and fc in Hz. FlJ·RBLB INPUT CHARACTERISTICS Output impedance •••••.••••• Maximum output voltage .••••. Noise (input shorted) •...••••. Offset voltage .............. R' = 159,~ 10' (Kill The FC setting range can be shifted to a lower band by adding external capacitors Cext. The equation shown below should be used for reference. - FLJ-RBLA ........ SUm)! 2 model (100Hz-20KHz) Rt = 15.9,: 10' (Kill - O.15dB O.3dBmax. O.ldB O.OO5'/O@lKHz ROLLOFF CHARACTERISTICS a ....................... Suffix 1 model (10Hz-2KHz) where fc is measured in Hz. PASS BAND CHARACTERISTICS Gain Gain after Rf adjustment Ripple POp Ripple ~.9fc ••••••••.••••• Ripple after Rf adjust .••.••••• Distortion ratio •••.•••.••••• TECHNICAL NOTES 1. Setting the cutoff (central) frequency is accomplished with 8 external resistors which are equl;Il in value for lowpass filters and 6 external resistors which are equal in value for bandpass filters. The relationship between the resistance Rf of the external resistors and the cutoff frequency fc is as follows: -100 0.1 1 10 Normalized frequency flfc 100 <-so -60 0.1 1\ \ \ \ ORDERING INFORMATION 1\ 1 Normalized frequency fife 10 low Cutoff Frequency Type (10Hz-2KHz) FLJ-RSLA1: 135dB/oct., 8-pole FLJ-RSlB1: 100dB/oct., S-pole FLJ-R3BA1: 3·pole pair bandpass High Cutoff Frequency Type (100Hz-20KHz) FLJ-RSLA2: 135dB/oct., 8-pole FLJ-RSlB2: 1OOdB/oct., S-pole FLJ-R3BA2: 3-pole pair bandpass 8-12 DATEl, Inc. 11 Cabot Boulevard, Mansfield, MA 0204!l-1194ITEl (508) 339-3000ITLX 174388/FAX (508) 339-6356 FLJ-UR Series Single In-line Hybrid Resistor Tuneable Filter FEATURES MECHANICAL DIMENSIONS (Fig. 2) INCHES(mm) • Small and thin size • A variety of families • Cutoff frequency fc is set by only two or four resistors • Light weight, low cost 2.03(51.5) I- i----t-----;~! . -:!. " GENERAL DESCRIPTION The FLJ-UR series filters are single in-line package resistor tuneable filters. They are small in size and can reduce installation space on the printed circuit board. The cutoff frequency can be easily set by only two or four external resistors. The series has a variety of products, allowing system designers flexibility in selecting filters to suit their application. IAI (8) IT' 0.05(1.2) Pin cross section: O.02xO.01 (O.SXO.2S) Analog input Analog GND +15V -15V FU-UR4LB1/2 For Immediate ASSistance, Dial 1-800-233-2765 output 8-13 FL.J·UR Series SPECIACATIONS Typical at R=31.S k~, 25°C and ± 15V supply voHage unless otherwise specified. OUTPUT CHARACTERISTICS Output Impedance ............ 1000 max. Maximum Output VoHage .". ± 1OV min. Load Resistance ............... 10 kO min. Noise (10-500 kHz) .......... 140 p,V max. Offset Voltage .................. ±30 mV max. zero adjustable COMMON SPEClACATlONS TO ALL MODELS ABSOLUTE RATINGS Supply voltage (± Vs) .... ± 1SV Input voltage ................ ±VS POWER SUPPLY AND ENVIRONMENTS Supply Voltage ................. ± 15V Supply Voltage, Operating Range .............. ±5V-±1SV Operating Temerature/ Humidity Range ............... -20°C-700C, 10-95%RH Storage Temperature/ Humidity Range ............... -30°C-SO°C, 10-S0%RH FREQUENCY CHARACTERISTICS fcaccuracy .................. ±3% max. (with 0 dB gain at the frequency given in Note '2) INPUT CHARACTERISTICS Input Impedance ........... 50 ill min. Maximum Input Voltage ±10V SPECIFICATIONS "'(4 POLE MODELS) No. of poles/characteristics Type Model fc ( 3 dB) characteristics Suffix 1 model Range' Suffix 2 model Setting Pass band characteristics Gain·' Ripple Upper-limit frequency (small signal) Rollalf characteristics Rolloff Attenuation volume (112 fc or 2ic) Minimum attenuation Attenuation at 1 MHz Output characteristics OIIset drift Distortion rate" 51_rate Quiescent current/peckage Quiescent current (@l±15V) Package 4·pole lowpass Butterworth FLJ-UR4LA 4·pole lowpass Chebyshev. FLJ-UR4LB 40 Hz-1.6 kHz 400 Hz-20 kHz by 4 external resistors ·Same as left o dB±0.3 dB - I I 0.28 dBp-p - L I I I I I I 42 dB/oct or equivalent 55 dB 46 dB 24 dB/oct 24 dB 4·pole highpass Butterworth FLJ-UR4HA I I I 4-pole hlghpess Chebyshev FLJ-UR4HB ·Same as left 400 Hz-5 kHz I I I 'Same as left o dB±1 dB I I I 50 kHz± 1 dB max:" 24 dB/oct 24 dB 0.28 dBp·p 42 dB/oct or equivalent 55 dB 46 dB 70 dB min. 3OI'V/oC 0.01% I I - I +12 mA 20 pins SIP (A) 151'V/oC 0.1% 2V1l'sec +8 mA +16 mA +16 mA SPECIRCATIONS 2 (2 POLE AND 1 POLE PAIR MODELS) No. of poles/characteristics Type Model fc (- 3 dB) characteristics Suffix 1 model Range*1 Suffix 2 model Setting Pass band characteristics Gain·' Upper-limit frequency (small signal)"" Rollol! characteristics Rollalf Q Attenuation volume (1/2 fc or 2 fc) Attenuation at 1 MHz Maximum attenuation (f.) Output characteristics OIIset drift Distortion rate' Slew rate Quiescent currenl/package Quiescent current (@+15V) Package I 2-pole high lowpass Butterworth FLJ-UR2LH 1-pole pair bandpass Butterworth FLJ-UR1BA 40 HZ-l.6 kHz 400 Hz-20 kHz ·Same as left 400 Hz-l0 kHz I I o dB±0.3 dB 100 kHz±1 dB HPF 12 dB/oct 12 dB 70 dB min. LPF 2-pole pelr bandpass Butterworth FLJ-UR2BA by 4 external resistors o dB±1 dB - 2-pole pair band elimination Butterwo;th FLJ-UR2EA -Same as left by 2 external resistors l I - 5 35 dB 5 '. 17.5 dB 'Ssme as left 1 J I I o dB±0.3 dB 50 kHz± 1 dB max. 5 60 dB 15I'V/"c 0.1% 2V/I'8ec HPF I 30 I'VI"C 0.01% 2V1p.Sec +12 mA +8 mA 20 pins SIP (A) .,: AdditiOf'l of 2 or 4 external capacitors allow extension to lower band. '2: FW-UA4LA, 4LB; fell0, FLJ-UR4HA; 3.3 te, FLJ-UA4HB; 10 Ie (fc~3 kHz). 3.3 Ie (fc>3 kHz) FW-UR2LH; lell0 (LPF). 10 Ie (HPF) S-14 I +20 mA 20 pins SIP (B) '3: Gatn of 0 dB at above.stated frequencies. (See '2) '4: . Connection of a specified pin to GND allow 10,20, 30, 40 and SO. External resistors allow a range of 1.81~O~50. DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 0204S-1194ITEL (50S) 339-3000ITLX 1743SS/FAX (50S) 339-6356 FLJ·UR Series 2. Use metal film resistors of 1% tolerance for fc setting. When making a higher-order filter, use more accurate resistors. b. FLJ-UR2BA1/2 • An input frequency of 1.0734xfc is provided. • Tune VR, until the phase difference between the input Signal and the output signal at pin 9 reaches at 180° looking at a phase measuring instrument such as an oscilloscope. • An input Signal of frequency fc is given. • Tune VR2 until the phase difference between the input signal and the output signal at pin 20 is set at 0°. 3. Connect external resistors with short leads as close to the filter as possible. FI...J..UR4LA1/2 Block Diagram· (Fig. 3) TECHNICAL NOTES 1. Do not use a switching regulator. Use a well regulated ±15V power supply. Install 0.01 ~F bypass capacitors as close to the filter as possible. 4. Use external capacitors with good stability and high dielectric resistance. It is recommended to use multilayer ceramic capacitors or plastic film capacitors. 5. Regulate output offset voltage. by using an external trimmer (10 KG to 50 KG). 6. The FLJ-UR series filters are packaged single inline and are compact in size. Installation at high-density may cause temperature rises between elements. Installation with 0.8" or more of space between filters can eliminate the problem. 7. Relation between fc and external resistor/capacitor: With the FLJ-UR series. a cutoff or center frequency can be set by 2 or 4 external resistors. The values of R of 2 or 4 external resistors for normal use can be calculated as; R - 15.9x106 (0) fc (Hz) Suffix 1 model Analog input GND +15V -lSV FW-UR4HA1/2 Block Diagram (Fig. 4) 159x106 R (0) Suffix 2 model fc (Hz) Note: R, = R2 = R3 = R. lSK In certain applications the resistance of each of 2 or 4 resistors may be changed. R, to R. shown in the block diagrams are the external resistors explained here. In standard use, the fc can be set to a minimum of 40 Hz. This is because the values of R have to be increased to about 400K according to the relation between Rand fc. The fc setting range can be expanded to lower band by adding 2 or 4 external capacitors. R R - 159x103 (Cext+0.01) fc 159x103 (Cext+0.OO1) fc (0) Suffix 1 model (0) Suffix 2 model FW-UR4HB1/2 Block Diagram (Fig. 5) R,' where Cext is measured in p.F and Fc in Hz. In the applications in which the output offset, time drift, or output noise must be minimal, use the above external capacitors if the values of external resistors exceed 100 kO each. 8. How to tune fc As shown in the specifications, the fc setting accuracy is 3% depending on the accuracy of elements used. There is no practical problem in tuning when they are used as lowpass or highpass filters. However, bandpass filters and band elimination filters may require sharp tuning. Such filters can be tuned with external trimmers as shown in Fig. 10. R" R2 and VR, are not used with the FLJUR1BA1/2. a. FLJ-UR1BA1/2 • An input signal of oscillating frequency fc is given. • 1/0 signals are monitored with a phase measuring instrument such as an oscilloscope. • Tune VR2 until the phase difference between 110 signals can be reduced to 0°. For Immediate Assistance, Dial 1-800-233-2765 Analog GND +15V -15V 'oput Cf in each-figure is 10000 pF for suffix 1 model and 1000 pF for suffix 2 model. 8-15 FLd·UR Series FU-UR2LH1/2 Block Diagram (Fig. 6) t::"utlog· FLJ-UR2EA1/2 Block Diagram (Fig. 9) GNO +1SV-15V FW-UR1BAl/2 Block Diagram (Fig. 7) fc tuning method (Fig. 10) GND +ISV -ISV ORDERING INFORMATION "'FU.UR2BA1/2 Block Diagram (Fig. 8) LOW CUTOFF FREQUENCY TYPE (40 Hz-1.6 kHz) FW-UR4LA 1: FW-UR4LB1: FW-UR4HA1: FW-UR4HB1: FW-UR2LH1: FW-UR1 BA 1: FW-UR2BA 1: FW-UR2EA1: 4-pole lowpass, Butterworth 4-pole lowpass, Chebyshev 4-pole highpass, Butterworth 4-pole highpass, Chebyshev 2-pole lowpass/highpass, Butterworth 1-pole pair bandpass, Butterworth 2-pole pair bandpass, Butterworth 2-pole pair band elimination, Butterworth HIGH CUTOFF FREQUENCY TYPE (400 Hz-5 kilO kl20 kHz) Cf in each figure is 10000 pF for·suffix 1 model and 1000 pF'for suffix 2 model. 8-16 FW-UR4LA2: FW-UR4LB2: FW-UR4HA2: FW-UR4HB2: FW-UR2LH2: FW-UR1BA2: FW-UR2BA2: FW-UR2EA2: 4-pole 4-pole 4-pole 4-pole 2-pole 1-pole 2-pole 2-pole lowpass, Butterworth lowpass, Chebyshev highpass, Butterworth highpass, Chebyshev highpass/lowpass, Butterworth pair bandpass, Butterworth pair bandpass, Butterworth pair band elimination, Butterworth DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-11941TEL (508) 339-30001TLX 174388/FAX (508) 339-6356 FLJ-VL, VH, VB Voltage Tuneable Filter FEATURES • Cutoff frequency is tuned by external voltage • Wide range of control frequency • Small in hybrid GENERAL DESCRIPTION MECHANICAL DIMENSIONS INCHES(mm) FW-V Series filters cutoff frequency or center frequency can be set with an external control voltage. Hybrid construction has made it possible to build highly reliable, high performance filters in small size at low cost. FW-VL is a lowpass filter and FLJ-VH is a highpass filter. Both filters have 24dB/oct of rolloff characteristics. FW-VB is a bandpass filter which has 12dB/octBW at Q=5. l-nmnmnnmII'~1 PIN SECTION O.OlXO.OI (0.5XO.l5) --------------------1 -.Lr-- l . ll (53.9)--1 LL o.z6(6.5)/ T~.,jlJ"lllllllll~rllli .ll(.5.0) T 0.I(l.54) 2.14(54.4) , PIN CONNECTIONS PIN 1 2 4 7 8 9 10 11 14 15 16 17 18 20 FUNCTION INPUT GND Rq1 Cext1-1 -Rq1, Cext1-1 Cext1-2 Cext1-2 Rq2 Cext2-1 Rq2 Cext2-1 Cext2-2 Cext2-2 ZERO ADJ. OUTPUT PIN 21 22 34 36 37 40 FUNCTION CONTROL V. INPUT GND. -vee -15V GND GND +Vee +15V DO NOT CONNECT UNUSED PINS TO OTHERS. For Immediate Assistance, Dial 1-800-233-2765 8-17 FLJ-VL, VH, VB SPECIFICATIONS Typical values at 25'C with ±15V supply, 10V control voltage, ±1V rated input unless otherwise specified. FLJ-VL (Lowoass Filterl FLJ-VB (Bandpass Filterl FLJ-VH (Hiahpass Filterl ABSOLUTE MAXIMUM Power Supply Voltage ............• Input Voltage .................... Control Input Voltage ............. ±18V ±Vcc ±Vcc • "Same as FW·VL" • "Same as FW·VL" • "Same as FW·VL;' • "Same as FW-VL" • "Same as FW·VL" • "Same as FW-VL" FILTER CHARACTERISTICS Frequency Set Range ............. Frequency Set Accuracy ..•..•..... Control Input Voltage Range ....... Control Input Impedance .......... Characteristic .......•.......•...• Rolloff .....•.......•••.•.•...••. Pass Gain vs. Control Input V. ...... Distortion ....................... Frequency Set T.C. ............... 100Hz -100KHz ± (3%+0.01% F.S.) max. +10mV-+l0V 50 Kohm min . 4 pole Butterworth 24dB/oct ±0.5dB 0.1% max . ±O.03%/'C · 200Hz - 20KHz 2OHz- 20KHz AMPLIFIER CHARACTERISTICS Input Voltage .................... Rated Input Voltage .......••...... Input Impedance ................. Offset Voltage ................... Offset V. Variance vs. Control V.....• Temperature Drift ................ Noise CD ••••••••••••••••••••••••• Output Voltage/Current ........•... Output Impedance ............•••. Load Resistance ................. Small Signal BW ................. ±10V min . ±1V 50 Kohm min . ±10mV Zero Adjustable ±20mVmax. 300pVrC 800pVrms max. @10Hz- 300KHz ±10V/5mA min. 500hm max. 10Kohm min. DC-fc POWER REQUIREMENTS & ENVIRONMENT Power Supply Voltage •.....•..•..• ±15V, +10%, -5% Current ...••..•.....•..•.....•.. ±36mA Operating Temperature Range ...... -20'C - +70'C Operating Humidity Range ......... 10%-95%RH Storage Temperature Range .....•.. -30 'C - +80 'C Storage Humidity Range ........••. 10%-80%RH · · +10mV~+10V +l00mV - +10V · 2 pole pair Butterworth 12dB/oct BW(Q=5) ±ldB 4 pole Butterworth 24dB/oct ±0.5dB ·· ··· ·· · ·· ··· ·· · ·· ·· ··· · ±2V min. ±10V min. ±2V/5mA min. ±10Vl5mA min. ·· - fc -300KHz ·· ·· ·· Typically <300 ~Vrms for the FW-VH. The FW-VUVB are typically <300 ~Vrms for control voltages up to 2V and <.500.~Vrms for control voltages from 2 to 10 Volts. (j) TECHNICAL NOTES 1. The rated input voltage is ±lV. The maximum performance is obtained if input voltage does not exceed this range. 2. Thesefiltersare 4pole Butterworth(2pole pair)filters. Cutoff frequency is controlled by external voltage. The relationship between control voltage and cutoff frequency is linear (=proportional). Cutoff frequency ranges can be shifted toward lower frequency region if four external capacitors are added. See Figure 3. FLJ-VL: Cextl, Cext 2 FLJ-VB, VH: fc(max) x ~7T x 6.36 X 10' 250 X 10"2 1 1250 x 10"2 Cex tl , C ext 2 = fc(max) x 27T x 6.36 X 103 Cextl, Cext 2: F (Farad) fc(max) : -3dB frequency at 10V control voltage. 3. Zero offset adjustment range is approximately ±50mV. 4. Control input voltage signal has approximately 10KHz of frequency response. However, it takes long time before the output DC offset (=approx. 1OmV) settles under the new fc 8·18 set. It is not recommended to use alternating signals for the control input, depending on applications. The cutoff frequency shall be affected by unstable control voltage if it is small signal, even if.it is DC. 5. FLJ-VL can be used as Bessel filter. Connect Rql = 95.3KO and Rq2 = 9.53KO as shown Figure 3. External capaCitors should be: _ ( 100 ) Cextl - 250 fc(max) (KHz) x 1.43241 -1 (K~c:i Cext2 = 250 (fe(max) x 1.60594 1) fc(max) :;;; 62.2KHz, -3dB frequency at 10V control input voltage. Cext1, Cext2: pF (pico Farad) DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048·1194ffEL (508) 339·3000ffLX 174388/FAX (508) 339-6356 FL.J-VL, VH, va TYPICAL CONNECTION (Fig. 3) c..~ ,..*-.. (, , Input 17 A.J-,,Fl_,"," ru-wt .. .. •. 7/10.111 +'.., -,.., GMJ 31 2D ... , 11.< +'.., Output IZer!"ad~ -15V AMPLITUDE VS. FREQueNCY (Fig. 4) FU-YL (Fig. 4-1) 0 -I 0 -20 ~blv ~~,V ~I~ I\-'OV 1\ 1\ 1\ 1\ 0 1\ 1\ 0 \, -60 1\ 100 IK 1\ 10K 1 -I 0 -30 -OIl \ -60 I~lOOK -60 1\ 1M O.OIV II J. J. o.lV II -20 1\ \ -.l 0 Control V. 1\ \ -60 -70 10 FU-YH (Fig. 4-2) II II I 10 100 11 II 1 1 F requency(Hz) V 11 II 1 1 11 :1 l~,:!v. IV IK 11 10K lOOK Frequency(Hz) FU-YB (Fig. 4-3) I 0 JI~·lV r~O.3V JlV-IV -I 0 Control v. I 1\ J \ I 1\ J \ /1\ / V 'II V 'II \ /\ r\ /\ r\ \ -20 CD -30 i -. I r\,3V JI~IOV 0 ORDERING INFORMATION V j J ~ ) [)(\ \ \ / I \k" Y 1\ \ /V v 1/ \ j \ 1\ \ '-... o MODEL NO. DESCRIPTION FLJ-VL Low-pass filter Butterworth 4 pole Band-pass filter Butterworth 4 pole High-pass filter Butterworth 4 pole -so FLJ-VB -60 -7 .II 5 / 100 /\.. IK \.. 10K Z Frequency(Hz) For Immediate Assistance, Dial 1-800-233-2765 "' 5 FW-VH lOOK 8-19 Contact DATEL for your Data Acquisition component needs. Dial 1-800-233-2765 for Applications Assistance 8-20 DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194fTEL (508) 339-3000fTLX 174388/FAX (508) 339-6356 FLT-C1 Programmable 7th Order, Low-pass, Switched Capacitor Active Filter FEATURES FLT-C1 Mechanical Dimensions Digital tuning Stopband attenuation >76dB at 31e Built-in sample-hold Programmable gain of 1, 2, 4, 8 • Dynamic range of 85dB • 12-Bit precision I 0.605 (15,37) 0.585 (14,86) DESCRIPTION 0.085 (2,16)1 1.620 (4115) 1 0.060 (1,524) 1.580 (40: 13) - - 0.040 (1,016) + - DATEL's Model FLT-Cl is a monolithic, 7th order, lowpass active filter for applications requiring sharp, fast attenuation rolloff. Exceptionally low noise performance of this switched capaCitor filter permit it to be used in applications requiring 12-bit accuracy. - • I -t-~- • t t ,Vill- 0.050 (1 Typical A combination of an 8-bit control input and the clock frequency set the corner frequency over a range of 78 Hz to.·20 KHz. A 2-bit control input selects the gain. A built-in oscillator (less crystal) is provided for systems where a system clock is not available. 0.175(4,45) Typical -11--11-- 0.020 (0,0508) 0.016 (0,406) 0.105 (2,67) 0.095 (2,42) ORDERING INFORMATION CS WR os MODEL DESCRIPTION FLT-C1 7th Order, Low-pass, Switched Capacitor Active Filter 00-07 AS AO 21271291311321 I I I I 5-13 I I I MICROPROCESSOR INTERFACE t Gl-G2 3,4{ I 25 1 I ACTIVERC FILTER DATA LATCHES /' I I 24 RCOUT 26 SC,. For Immediate Assistance, Dial 1-800-233-2765 20 I I RCIN CLKIN 191 H 181 I +n +m I SWITCHED CAPACITOR FILTER 231 ~ Voo I CRYSTAL OSCILLATOR I po X2 Xl r!- Vss ~ GNO I 15 CLKoUT 14 SYNC 17 CNVRT ~ DECIMATOR l- gg SCOUT I 1 30 AAiSM 8-21 FLT·C1 FUNCTIONAL SPECIFICATIONS Typical at 25°C range unless otherwise noted. Specifications subject to change without notice. FILTER CHARACTERISTICS Frequency Range Voltage Gain Gain Accuracy (G=1) Offset Voltage (G=1) Filter Response (Relative to DC Gain) at 1.5 fc at2fc at3fc Input Signal Level Output Voltage Output Current Passband Ripple Band edge Tolerance Wideband Noise, 20 KHz, BW Harmonic Distortion , Dynamic Range 78 Hz to 20 KHz 1,2,4,or8 ±0.1% 5mV 7-pole Chebychev -30 dB max. -S2dB max. -76 dB max. ±3Vmin. ±3V ±0.6mA ±O.ldB ±O.S% 100 j!Vrms max. -72 dB 8SdB min. CLOCK Pin Functions Name Function Vss CS Gl·G2 Negative supply voltage. Chip select; active low. The digital inputs that control the DC gain of the SC filter. The digital inputs that control the RC filter band edge, SC filter band edge, and SC filter decimation rate. This digital input contrals the sampling instant for the SC filter decimated output; active low. Master clock output capable of driving 1 standard TTL load. It is a buffered version of either ClKIN or the internally generated crystal oscillator output. Positive supply voltage This digital output indicates that the SCOUT output has settled and can now be converted or sampled (drive capatibility is 1 standard TTL load); active low. An external crystal is connected between these pins to generate an accurate clock for chip operation. The master clock input. Forcing ClKIN to vss enables the on-chip oscillator (external crystal). Ground. SC filter output. This digital input is used to power down the analog circuitry; active low. RC filter output. RC filten input. . SC filter input (only valid when AAlSM is forced low). Write strobe; active low. Data strobe. This digital input controls whether the input to the SC filter comes from RCOUT or SCIN. Address strobe. Register address select. 00-07 -- SYNC ClKoUT Voo CNVRT Xl-X2 Input Clock Frequency (j) 1 MHz min. 4 MHztyp. ClKIN DIGITAL INPUTS Input High Input Low Leakage Current Input Capacitance 2.0V min. 0.8V max. 1 j!A max. 10 pF max. POWER SUPPLY REQUIREMENTS Supply Voltage Supply Current Power Dissipation ±SV (±S%) ±lSmA lS0mW (j) Also internal clock frequency. 'Internal clock requires external crystal. FUNCTIONAL DESCRIPTION The FlT-Cl is made up of two programmable filter sections used in different combinations to meet various applications. The switched capacitor stage (SCF), is a 7-pole, lowpass filter designed to provide an accurate, programmable passband for fixed or dynamic applications. The switching frequency may be derived either from a crystal oscillator or from a system clock. Since the filter band edge can be programmed by varying the frequency of the clock which controls the filter's switches, it can track the sample rate of an extemalAiD converter. Digital programming allows for band edges of up to 20 KHz and gains of 1, 2, 4, or 8. The RC filter stage is a low-order active filter with a bandedge accuracy of S%. This accuracy is adequate because the filter sampling rate is SO times greater than the band edge frequency_ 8-22 GND SCOUT PO RCOUT RCIN SCIN WR OS AAlSM AS AO The band edge of the RC filter is programmable to insure sufficient rejection of any SC filter harmonics. Ratio matching of on-chip resistors and capaCitors provides eight RC filter bandedges spanning a 12-to-l range. . A decimator, placed at the output of the SC filter, samples the differential output and converts it to a single-ended signal. In addition, the decimator can be programmed to allow an Integer decrease in the sampling rate by low filtering of the signal and keeping every Nth sample, similar to a programmable samplehold. By choosing the proper decimation rate, the hold time at SCOUT will be long enough to allow an AID conversion to take place without the need of external S/H components. An external S/H is recommended for hold times faster than 100 j!S to prevent more than 1/2 lSB of droop for a 12-bit AID converion. DATEl, Inc. 11 Cabot Boulevard, .Mansfield, MA 02048-1194ITEl (S08) 339-3000ITLX 174388/FAX (508) 339-6356 FLT·C1 Microprocessor Interface Timing Characteristics ADDRESS AD DATA Tl T2 00-07, Gl-G2 T3 T4 A S - -_ _ _J DS---------------------------~ W R - - - - - - - - - - - - - - -__ cs ______________________ ~ SCoUT Synchronization Timing ClKIN ~,_ _--,II,-_- --I 1-- T6 ClKoUT T9 T10 SYNC CNVRT - T7 L -_ _ J.!P Interface Timing Ref. Duration CS Hold Time Data Hold Time Data Set-up Time Address Hold Time Address Set-up Time T5 T4 T3 T2 Tl 10 nSec. min. 10 nSec. min. 100 nSec. min. 10 nSec. min. 20 nSec. min. SCOUT Ref. Duration Synchronization Timing SyncB Delay Time SyncB Set-up Time ClKIN To ClKOUT Delay ClKIN To CNVRT Delay Sync Pulse Width T8 T9 T6 T7 Tl0 100 nSec. min. 75 nSec. min. 50 nSec. max. 75 nSec. max. 75 nSec. min. RCF band edge RCF3dB BW D7 D6 D5 80 KHz 56KHz 40KHz 28KHz 14KHz 10KHz 7KHz 0 0 0 0 1 1 1 0 0 1 1 0 1 1 0 1 0 1 1 0 1 TOP VIEW DC Gain DC Gain G1 G2 1 2 4 8 1 1 0 0 1 0 1 0 FLT-C1 Clock to SCF bandedge Divide Down Ratio fClK/fc DO D1 D2 200 400 800 1,600 3,200 6,400 12,800 0 0 0 0 1 1 1 0 0 1 1 0 0 1 0 1 0 1 0 1 Decimator Sample Rate fSlH/fc D3 D4 25.000 12.500 6.250 4.167 0 0 1 1 0 1 0 1 X tc = O.ldB Bandwidth of the SC filter. fClK = Master clock frequency at ClKoUT fSIH = Sample rate at SCOUT output. For Immediate Assistance, Dial 1-800-233-2765 16 VDD 8-23 Contact DATEL for your Data Acquisition component needs. Dial 1-800;.233-2765 ,for Applications Assistance 8·24 DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048·1194fTEL (508) 339·3000fTLX 174388/FAX (508) 339·6356 FLT-DL 4-and 5-Pole High Frequency Digitally Programable Active Filters MECHANICAL DIMENSIONS INCHES (mm) 1.101 MAX. 1 FEATURES • • • • • • 1 Digitally programmable 4- and 5-Pole Cauer response Cascadable 7 Pole Cauer response Cutoff Frequencies to 1.2 MHz Small 32-pin DIP -55°C to +125 °C operation I (28,0) 0.190 MAX. ! I lil_--->,(4:.!.:,8"-,) I 0.150 MIN. (3,8) 0.010 x 0.018 KOVAR Pins 116 GENERAL DESCRIPTION 171 1 1 DATEL's FLT-DL series of 4- and 5-pole digitally programmable active filters are functionally complete, simple to use, and offer a wide range of frequency response options. The models offered operate over the frequency ranges of 100 KHz to 470 KHz and 250 KHz to 1200 KHz. I I BOTTOM VIEW 1 1 1 321 1 11 0.900 (22,9) The FLT·DL Series are Cauer response filters which can be cascaded to provide equivalent 7 pole Cauer performance. PIN DATEL's FLT-DL Series filters are manufactured using thick-film and thin-film hybrid technology and unique laser trimming schemes. TheSe filters are packaged in a space-saving 32-pin ceramic DIP. Units are specified for operation over the commercial temperature range of 0 to +70 °C and the military temperature range of -55 to +125 °C. 1 2 3 4-9 10 11-14 15 16 17 18 19·21 TECHNICAL NOTES 22 23 1. Use an external 50 Kohm potentiometer to reduce the small initial offset error to zero. Tie the wiper to pin 18, OFFSET ADJUST. Connect the other terminals of the potentiometer to the +/-15 volt power supplies. For operation without adjustments, leave pin 18 unconnected. 24 25 26·30 31 32 ~ 15 1.712 MAX. SPACES (43,5) "'T~ I NOTE: Pins have 0.025 Inch ±C.01 standoff from case. FUNCTION +vcc GROUND -VEE NO CONNECTION ANALOG OUT NO CONNECTION GROUND GROUND NO CONNECTION OFFSET ADJUST NO CONNECTION BIT 1 (MSB) BIT 2 BIT3 BIT 4 (LSB) NO CONNECTION ANALOG RETURN ANALOG INPUT OFFSET ADJUST 18 r-----I ANALOG INPUT 32 ANALOG RETURN 31, BIT 1 (MSB) BIT 2 BIT 3 BIT4(LSB) 1 POLE LOWPASS FILTER SECTION 10 ANALOG OUTPUT 22 23 24 25 2,15,16 +VCC GROUND For Immediate Assistance, Dial 1-800-233-2765 SECTION ADDED FOR 5-POLE FILTERS 8-25 FLT·DL ABSOLUTE MAXIMUM RATINGS PARAMETERS + 15V Supply (pin 1) -15V Supply (pin 3) Digital Inputs (pins 22-25) Analog Input (pin 31,32) Lead temperature (10 sec.) Junction temperature (TJ) Storage Temperature Power dissipation FILTER CHARACTERISTICS CONT. LIMITS UNITS -0.3 to +1S +0.3 to -18 -Vccto+15 -25 to +25 300 +175 -65 to +150 3 Vdc Vdc Vdc Vdc °C °C °C Walts Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. FUNCTIONAL SPECIFICATIONS MIN TYP MAX UNITS ±10 - - Volts - - Kohms Kohms - - Volts Kohms - - - - ±25 - mA Kohms 100 250 4 - - 400 1000 KHz DIGITAL INPUTS Logic Threshold Logic Input Impedance .1Vee ±20% -fOO OUTPUT CHARACTERISTICS Output Voltage Range ±10 1 DC Output Resistance Output Current Umlt (Short Circuit Protected) Recommended Load Resistance 2 - - - - TBD - TBD TBD TBD - Volts Ohms MAX UNITS ±14.25 ±70 ±60 ±15 ±15.75 Volts POWER REQUIREMENTS Rated Voltage Quiescent Current FLT-DL5 FLT-DL4 Power Dissipation - - - rnA 3 mA W - PHYSICAL/ENVIRONMENTAL Operating Temperature Range MC 0 to +70'C MM-55to+125'C -65 to +150'C Ceramic 32-Pin DIP Weight Input Voltage Range Input Impedance (Nonlnvertlng) Pin 1 Pin 3 - - Offset Voltage Offset Voltage Drift 010 +70'C -5510 +125'C Noise case INPUTS - TYP storage Temperature Range Apply at 25°C and at ± 15Vdc power supply voltages unless otherwise specified. 4 6 MIN TBD 2. Bypass each power supply with a 0.1 microfarad tantalum electrolytic capacitor. 3. Digital inputs are-binary. The truth table (Table 1) details the cutoff frequency for each filter and for cascaded pairs of filters as a function of input coding . 4. The frequency responses of the 4-pole and 5-pole Gauer filters are shown in Figures 2 and 3 respectively. Figure 4 details the response of a cascaded pair of frequency matched 4- and 5-pole filters. The response for a cascaded pair is similar to a 7-pole Gauer, as shown in Figure 5. 5. When cascading a 4-and a 5-pole filter pair, the order of connection is not important. The filters must, however, be frequency matched. FILTER CHARACTERISTICS Freq. Range (cascaded pair) FLT-DL41/51 FLT -DL42152 Programming Bits Programming Frequency Increments FLT-DL41/51 FLT -DL42152 Programming Accuracy Voltage Gain Passband Ripple FLT·DL Settling Time (to 0.01 %) fc=IMHz FLT·DL42 FLT·DL52 fc=100KHz FLT-DL41 FLT-DL51 Transition Slope FLT-DL41 142 FLT-DL51/52 FLT-DL4/5 stopBand Attenuation (to10MHz) FLT -DL41/42 FLT-DL51/52 S-26 20 50 TBD Unily .7 30 50 80 30 50 - - KHz - I1Sec - - dB/oct dB/oct dB/oct - - dB dB - 6 7 60 60 - - ,r--.... 20 dB/div. \ ~ - \ fl O.2%/div. / -....-....., V ........... KHz KHz - % Figure 2. 4-Pole CAUER Response I1Sec !1Sec "- lJSec. 20dB/div.f\ , \ \" I Y f \/ -...........0.2O/oIdiV. '" '-" . Figure 3. 5-Pole CAUER Response DATEL, Inc. 11 Cabot BOUlevard, Mansfield, MA 0204S·1194ITEL (50S) 339·3000ITLX 17438S/FAX (50S) 339·6356 FLT·DL Table 1. Cutoff Frequencies for Digitally Tuned Filters, and for Cascaded Combinations of Two Filters DIGITAL INPUT (BIN) CUTOFF FREQUENCY (KHz) CASCADED 41X51 42X52 FLT-DL41 FLT-DL42 FLT-DL51 0000 0001 0010 0011 103.8 124.6 145.3 166.1 259.5 311.4 363.3 415.2 121.5 145.0 170.1 194.4 303.8 364.5 425.3 486.0 100 120 140 160 250 300 350 400 0100 0101 0110 0111 186.8 207.6 228.4 249.1 467.1 519.0 570.9 622.8 218.7 243.0 267.3 291.6 546.8 607.5 668.3 729.0 180 200 220 240 450 500 550 600 1000 1001 1010 1011 269.9 290.6 311.4 332.2 674.7 726.6 778.5 830.4 315.9 340.2 364.5 388.8 789.8 850.5 911.3 972.0 260 280 300 320 650 700 750 800 1100 1101 1110 1111 352.9 373.7 394.4 415.2 882.3 934.2 986.1 1038.0 413.1 437.4 461.7 468.0 1032.8 1093.5 1154.3 1215.0 340 360 380 400 850 900 950 1000 \ 0.05%/div. /\ ---..-' V ORDERING INFORMATION \ 20dB/div. IY\r---.. Figure 4. 4- and 5·Pole Pair Response \ 0.05%/div. - ...., FLT-DL52 \ -- 20dB/div.- ..--- IV V Figure 5. 7·Pole CAUER Response For Immediate Assistance, Dial 1-800-233-2765 MODEL NO. DESCRIPTION FLT-DL41MC FLT-DL41MM FLT-DL51MC FLT-DL51MM 100 KHz,4 100 KHz,4 100 KHz,5 100 KHz,5 FLT-OL42MC FLT-OL42MM FLT-OL52MC FLT-OL52MM 250 KHz, 4 Pole 250 KHz, 4 Pole 250 KHz, 5 Pole 250 KHz, 5 Pole Pole Pole Pole Pole TEMP. RANGE Ot070·C -55 to 125·C Ot070·C -55 to 125·C Ot070·C -55 to 125·C Ot070·C -55 to 125·C Receptacle for PC board mounting can be ordered through AMP Inc., Part #3-331272-8 (Component Lead Socket) 24 required. For availability of MIL-STO-883 versions, contact OATEL. 8-27 Contact DATEL for up-to-date information on products covered by "Advanced" and "Preliminary" product data sheets. Dial 1-800-233-2765 for Applications Assistance 8·28 DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194fTEL (508) 339-3000fTLX 174388/FAX (508) 339-6356 FLT-U2 Micro-electronic Universal Active Filter FEATURES • State variable filter • LP, BP, or HP functions • 2-pole response • Low-noise operational amplifiers ·-55°C to +125°C operation • Low cost GENERAL DESCRIPTION The FLT -U2 is a universal active filter manufactured with a thick-film hybrid technology. It uses the state- variable active filter principle to implement a second order transfer function. Three committed operational amplifiers are used for the second order function while a fourth uncommitted operational amplifier can be used a a gain stage, summing amplifier, buffer amplifier or to add another independent real pole. MECHANICAL DIMENSIONS INCHES (MM) Two-pole low-pass, bandpass, and highpass output functions are available simultaneously from three different outputs, and notch and allpass functions are available by combining these outputs in the uncommitted operational amplifier. To realize higher order filters, several FLT-U2's can be cascaded. Q range is from 0.1 to 1,000 and resonant frequency range is 0.001 Hz to 200kHz. Frequency stability is 0.01%/OC and resonant frequency accuracy is within ±5% of calculated values. Frequency tuning is done by two external resistors and Q tuning. by a third external resistor. For resonant frequencies below 50Hz, two external tuning capacitors must be added. Exact tuning of the resonant frequency is done by varying one of the resistors around its calculated value. 16 15 14 13 12 11 10 510 .590(14,9) P'N~~~~l ONE IDENT. .195(4.9) " .900 (22,9) _ , ~ m?NRfL~J: ' -I 13 7 1 DATEL FLT-U2 The internal operational amplifiers in the FLT-U2 have 3 MHz gain bandwidth products and a wideband input noise specification of only 10nV/..JHz. 314 9 1-.lOOTYP (15,2) (2,5) +15VOC 4 CONNECTIONS DIAGRAM ,. ,. Ra R'N 11 HPOUT V' FLT-U2 BPOUT (TOP VIEW) LPOUT V- (1,2) aUF OUT GND 9 For Immediate Assistance, Dial 1-800-233-2765 6 12 . 15VDC 8-29 FLT·U2 FUNCTIONAL SPECIFICATIONS Typical at 25°C, THEORY OF OPERATION ±15V supplies, unless otherwIse stated. FILTER CHARACTERISTICS Frequency Range' ••••••••••••• ,QRange' •••••••••••.•.••••.•• f. Accuracy ••••••••••• . • • • • • •• f. Temperature Coefficient ••••••• 'Voltage Gain' •••••••••••••••••• 0.001 Hz to 200 kHz 0.1 to 1.000 ± 5% 0.01 %/OC 0.1 to 1.000 The FLT-U2 block diagram is shown in Figure 1. This is a second order state-variable filter using three operational amplifiers. Lowpass, bandpass, and high pass transfer functions are simultaneously produced at its three output terminals. These three transfer functions are characterized by the following second order equations: . H(s) = K, S2+~S+Wo2 LOWPASS H(s) = K2S S2+~S+Wo2 BANDPASS K3S2 S2+~S+Wo2 HIGHPASS AMPLIFIER CHARACTERISTICS Input Offset Voltage ••••..•••... Input Bias Current ••••••••.••••• Input Offset Current .••••••••••• Input Impedance •••••••.•••••.. Input Com. Mode Voltage Range •. Input Voltage Noise, wideband •••• Output Voltage Range. • .. • • • • • •. Output Current ................ Open Loop Voltage Gain •.••••••• Common Mode Rejection Ratio .•• Power Supply Rejection •••.••••• Unity Gain Bandwidth •.••..••••• Slew Rate ..................... a 0.5 mV typ., 6 mV max. 40 nA typ., 500 nA max. 5 nA typ., 200 nA max. 5 Megohms ± 12V min. 10 nV/.,fHz ± 10V min. ± 5 rnA min. 300,000 100 dB 10 INN 3 MHz 1 VipSl3c. Voltage, rated performance •.••.. ± 15V dc Voltage Range, operating. . • • • • •. ± 5V to ± 18V Qulescant Current. ............. 11.5 rnA max. , O°C to + 70°C -55°C to +125°C -55°C to + 125°C Ceramic 16'pin DIP (double·spaced) FOOTNOTE: 1. 100 " 5 x 1Q' optimally TECHNICAL NOTES 1. The FLT-U2 has simultaneous lowpass, bandpass, and highpass output functions. The chosen output for a particular function will be at unity gain based on Tables II and III. This means that the other two unused outputs will be at other gain levels. The gain of the lowpass output is always 10 dB higher than the gain of the bandpass output and 20 dB higher than the gain of the highpass output. 2. When tuning the filter and checking it over its frequency range, the outputs should be checked with a scope to make sure there is no waveform clipping present, as this will affect the operation of the filter. In particular the lowpass output should be checked since its gain is the highest. 3. Check f" the center frequency for bandpass and the cutoff frequency for lowpass or highpass, at the bandpass output. Here the peaking frequency can easily be determined for high a filters and the 0° or 180 0 phase frequency can easily be determined for Iowa filters (depending on'whether inverting or noninverting). 4. Tuning resistors should be 1% metal film reSistors with 100 ppm/oC temperature stability or better for best performance. Likewise external tuning capacitors should be NPO ceramic . or, other stable capacitor types. 8·30 A second order system is characterized by the location of its poles in the s-plane as shown in Figure 2. The natural radian frequency of this system is Wo. In Hertz this is fo = Wo . The resonant radian frequency of the circuit is different from the natural radian frequency and is: "" = Wo sin fIJ = .JWo2 - <7,2 The damping factor d determines the amount of peaking in the filter frequency response and is defined as: PHYSICAL/ENVIRONMENTAL Operating Temperature Range FLT-U2 ..................... FLT-U2M .................... Storage Temperature Range ••.•• Case ....................... a where K" K2, and Ka are arbitrary gain constants. 2... POWER SUPPLY REQUIREMENTS , a H(s) = d=cosfIJ The point at which the peaking becomes zero is called critical damping and is d = ~J2. a is found from d and is a measure of the sharpness of the resonance of the peaking: a =..!. 2d Also, a = fo = ~ - 3 dB Bandwidth 2<7, For high a filters the natural frequency and resonant frequency are approximately equal. "" '" Wo or f, '" fa This is true since "" = Wo sin fIJ and sin fIJ = 1 as the poles move close to the jw axis in the s-plane. For high as (a > 1) we therefore have for the second order filter: fa '" Bandpass center frequency '" Lowpass corner frequency '" Highpass comer frequency In the simplified tuning procedure which follows, the tuning is accomplished by independently setting the natural frequency and a of the filter. This is done most simply by assuming unity gain for the output of the desired filter function. Unity gain means a gain of one (±) at dc for lowpass, at center frequency for bandpass, and at high frequency (f> >fo) for highpass. Unity gain does not apply to all outputs simultaneously but only to the chosen output based on the component values given in the tables. Figure 3 shows the relative gains of the three simultaneous outputs assuming the bandpass gain is set to unity. Note that lowpass gain is always 10, dB higher than bandpass 'gain and highpass gain is·always 10 dB lower than bandpass gain. DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-11941TEL (508) 339-30001TLX 174388/FAX (508) 339-6356 FLT·U2 SIMPLIFIED TUNING PROCEDURE 1. Select the desired transfer function (lowpass, bandpass, or highpass) and inverted or non inverted output. From this determine the filler configuration (inverting or noninverting) using Table I. TABLE I FILTER CONFIGURATION 7. This procedure is based on unity gain output for the desired function. For additional gain, the fourth uncommitted operational amplifier should be used as an inverting or noninverting gain stage following the selected output. See Figure 4. A third pole on the real axis of the s-plane may also be added to the transfer function by adding a capacitor to the gain stage as shown in Figure 5. INVERTING INPUT NONINVERTING INPUT OUTPUTS' 2. Starting with the desired natural frequency and 0 (determined from the filler transfer function or s-plane diagram), compute foO. For foO> 1O· the actual realized 0 will exceed the ·calculated value. At foO = 10· the increase is about 1% and at foO = lOs it is about 20%. HP J BP~ R... ~ ---il--'- • C 14 ' • LP ~, I lOOK INVERTING CONFIGURATION LOWPASS Rl R2 100K OPEN R3 100K 3.800-1 BANDPASS OX 31.6K OPEN lOOK 3.480 HIGHPASS 10K OPEN lOOK 6.640-1 -f Figure 1. FLT-U2 Block Diagram +jw 4. Noninverting Configuration. Using the value of 0 from Step 2 find R2 and R3 from Table III. Rl is open, or infinite. TABLE III .1 lOOK 3. Inverting Configuration. Using the value of 0 from Step 2 find Rl and R3 from Table II. R2 is open, or infinite. TABLE II I3 c) r--H-- Relationships W1 :=: Wo sin" = "';w02 -o,2 d Q = cos e = J... =~ 2d NONINVERTING CONFIGURATION Rl R2 316K 0 R3 lOOK 3.160-1 LOWPASS OPEN BANDPASS OPEN 100k lOOK 3.480-1 HIGHPASS OPEN 31.6K 0 100K 0.3160-1 to - 3 dB Bandwidth +" -iw, x------- 5. Using the value of fa from Step 2, set the natural frequency of the filler by finding R. and Rs from the equation: -jw R. = Rs = 5.03 X 107 Figure 2. S-Plane Diagram fa where R. and Rs are in ohms and fo is in Hertz. The natural frequency varies as y'R.Rs and therefore one value may be increased and the other decreased and the natural frequency will be constant if the geometric mean is constant. To maintain constant bandwidth at the bandpass output while varying center frequency, fix R. and vary Rs. 6. For fo<50 Hz the internal 1000 pF capacitors should be shunted with external capacitors across pins 5 & 7 and 13 & 14. If equal value capacitors are used, R. and Rs are then computed from: R. = Rs = 5.03 X 1010 (C in pF) foC For unequal value capacitors this becomes: X 10 10 R. = Rs = 5.03 (C 1C2 in pF) f oy'C 1C2 In both cases the capacitance is the sum of the external values and the internal 1000 pF values. For Immediate Assistance, Dial 1-800-233-2765 20, + 10 r-_...;L;.;.Ow.;;.:P;.;. ... ;;;-._ _...:... 40dB/Decade -10 IH(sll (dB I -20 -30 -40 0.1 0.5 1.0 5.0 10.0 10 RELATIVE FREOUENCY Figure 3. Relative Gains of Simultaneous Outputs, Q=l 8-31 FLT·U2 R, R, /"X'- >-______-{) OUT I x' UNCOMMITTEO OPAMP ~ FLTU2=1 / ~~--~~~;------------+-u , .",. x,, G = 1 + .!h G = - R, R, Figure 4. R, Uncommitted Op Amp Gain Configurations FLTU2=2 ' . . x...... C c, IN OUT Figure 6. Realization of a Complex Multipole Filter R R R:+R., POLE FREQ = 2"~7C. I c• "" PO.LE FREQ = 2~R.C. Figure 5. Using the Uncommitted Op Amp to Add a Real Axis Pole >--4--0 OUT ADVANCED FILTERS All of the common !liter types can be realized by using cas- .. caded FLT-U2 stages. This includes multi-pole Butterworth, Bessel, Chebyshev, and Elliptic types. The basic procedure is to implement each pole pair with a single FLT-U2 and cascade enough units to realize all poles. A real axis pole is implemented by an uncommitted operational amplifier stage. Each stage should be separately tuned with an oseillator and scope and then the stages connected together and checked. See Figure 6. Figure 7. Realization of Notch Filter A notch filter can be constructed in several ways. The first way is to use the FLT-U2 as an inverting bandpass !liter and sum the output of the filter with the input signal by means of the uncommitted operational amplifier. This produces a net subtraction at the center frequency of the bandpass which produces a null at the output of the amplifier. (see Figure 7). Likewise lowpass and highpass outputs (which are always in phase) can be subtracted from each other with an external operational amplifier. The highpass output must have some gain added to it, however, so that its gain is equal to that of the lowpass output. A third method is to use two separate FLT-U2's, one as a two-pole lowpass filter and the other as a two-pole high pass filter. Again the outputs are subtracted in an operational amplifier. This method permits independent tuning of the two sections to get the best null response. ORDERING INFORMATION MODEL FLT-U2 FLT-U2M 8-32 OPERATING TEMP. RANGE O°C to + 70°C -55°C to + 125°C DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-11941TEL (508) 339-3000ITLX 174388/FAX (508) 339-6356 WIDE-RANGING, DC-DC POWER CONVERTERS NEW 20 WATT, WIDE-RANGING, DC-DC POWER CONVERTERS (2" X 2" X 0.4S") Input (Vdc) Output Input Current No Load/Full Load Output Noise & RIPPLE Efficiency (Min@ F.l.) Line/Load Regulation Model (TYP) 4.6· 13.2V (5V, ~)_.~~~:2~~ _ _ ~~!!3.78 A -:5:::0~m'CV:"p~·P~_ _c:;75::::0;'C-0_ _ ±O.2% I ±O.5%,_ _ _U",W,=R-=:3".31",4=25:;0:=,-O:,5::--_ ~~j].~~:..~.~~~?_~ 20 mA/1.7,-7.:.:A_ _..o:50",m",V"----,,p·LP 76% 18 - 72V (48V, Nom) __ ~.3V,~_~_~!E:~~_~ _ _ _5_0 ~~ _79% 4.6-13.2V (5V, Nom) 5.0V,3.~g ~__ __~O mA{~f!~~~ ______ .§Q mV P-E ___ . 80% 9.0 - 18V (12V, Nom) 5.0V,4.0 A ~.!~....:..?--.?~ (48V, _._~i':!.'4.0 A Nom) 4.6·13.2V (5V, Nom) ±12V,O.625 A 15 mN2.032 A 10 mA/O.50S A 40 mM.829 A ~- 50 mV pop ____ 50 mV 18V (~2V, N~f-=---_ ±1~O.83.ii:~'::_ 40 mN2~_ .. _ 18 - 72':'~~V, Nom) ±12V,0.830 A 10 mAIO.508 A 4.6 - 13.2V (5V, Nom) ±15V,0.600 A 40 mAll.829 A p-=~___ .-=-±0",.2"-0;',,,0,-,1±",0",.5,,"I.,,-0___-"U-"W"'Rc:-3"'.31"'4B""'50'--"'01.o=2 ±O.2% I ±O.5% UWR-3.3{~~~_._._ ±O.2% I +O.5%_ _ _UWR-5I~OOO-Q~ ___.. __ 82% ±O.2% I +0.5% UWR-S/4000-D12 82% ±O.2% / ±O.5% UWR-S/4000-048 85 mV pop 8824~00:---_==+0",.2,,"I.,,-01,-,±"'-"%,-_ _...B,,,W,,Rc.-121625-0S .~.2%/~ BWR-12f830-~_ 75 mVPe.--"-p_ _---=:::7;7--' 85 mV pop 82% ±0.2%!+1% BWR-12fB30-048 .___ ~mV p-p _ _ ~_._~?_{ !.:!.yo______ .!~R-1SI~QQ.-.Q!L .___ _ ~~~(12V,Nom) _ _±15V,~~~m~:!..:5~~ ~_~5~'!~~ 84% ~%1±1% ~'?~YJ!~V_, __~~)_ _±15V,0.670A__ ~~O.508A _ _~5mV.E:L._~~ NEW, 10 WATT, WIDE RANGING, DC-DC POWER CONVERTERS (2" 4.7 - 7.0V (5V, Nom) 9.0 - 18V (12V, Nom) 18 - 72V (48V, Nom) 4.7 - 7.0V (5V, Nom) 9.0 - 18V (12V, Nom) X ±O.2O/~±1% _ _ _ BWR-1S/670-0~ __ . ___ BWR-~IQ:.048 . __ 1" x 0.375") 3.3V~_A_ 30 mA/l.715 A 50 mV pop 70% ±0.2% 1 +0.5% UWR-3.3/1800-05 3.3V,2.5 A 3.3V,1.80 A 30 mAlO.915 A 15 mAlO.170 A 50 mV pop 50 mV pop 75% 75% 5.0V,1.60 A 5.0V,2.0 A 30 mAl2.160 A 15 mAll.03 A 50 mVp-p 50 mVp-p 74% 81% ±0.2% (+0.5% ±0.2% I ±0.5% ±0.2% / ±0.5% ±O.2% I ±0.5% UWR-3.3/2500-012 UWR-3.3/1800-048 UWR-S/1600-0S UWR-5/200o-012 ±O.2% / ±0.5% +0.2%/+1% UWR-5/1800-04B BWR-5/70o-05 18 - 72V (24/48V) 5.0V,1.80 A 15 mNO.240 A 4.7 - 7.0V (5V, Nom) ±5.DV,0.70 A 30 mAll.842 A 50 mV p-p 50 mV pop 76% 9.0 - 18V (12V, Nom) 4.7 - 7.0V (5V, Nom) ±5.0V,0.80 A ±12V,0.335 A 15mAlO.830 A 40 mAl2.1 A 50 mV p-p 15 mV pop 80% 76% ±0.2%/±1% BWR-5/800-0~~ _ _ _ ±0.2%/±1% BWR-12/335-05 9.0 ·18 (12V, Nom) +12V,0.415 A 35 mA/l.00 A +0.2%1+1% ±0.2%1±1% BWR-12/415-012 BWR-12/415-048 +O.2%~+1% +0.2%1+1% BWR-15/275-D5 BWR-15/330-012 +0.2%/+1% BWR-15/330-04B 18 - 72V (24/4~~ No~) ____:t:!.2~,0.415 A 4.6 - 13.2V (5V, Nom) ±15V,0.275 A ±15V,0.330 A 9.0 - 18V (12V, Nom) +15V,0.330 A 18 - 72V (24/48V, Nom) 78% 25 mV pop 83% ____ ~~AlO.260.!-_ _ _ 50_~.y pop 40 mA/2.142 A 15 mVp-p 25 mV p.p 35 mAlO.992 A 80% 77% 84% 50 mV e-p 81% 15mNO.257 A NEW, 3 WATT, WIDE RANGING, DC-DC POWER CONVERTERS (1.2S"xO.S"xO.43S") 18 - 72V (48V, Nom) 5.0V,0.50 A 10 mNO.069 A ~~.OV(?.Y~~2V,0.1~~.~~?..~~ __. 9.0 - 18V (12V, Nom) +12V,0.125 A 18 - 72V (48V, Nom) 15 mAlO.333 A ±12V,O.125A 10 mAlO.076 A ±15V,0.085 A ±15V,O.100A 25 mAlO.729 A 9.0-18V(12V,Nom) 18-72V(48V,Nom) ±15V,0.100A 10 mAlO.076 A ~-~.~J5V, Nom) _ 15 mNO.333A For Immediate Assistance, Dial 1-800-233-2765 100 mV p.p 75% 75mVp-p 70% ±0.2% 1 =±"'0."-5°,,"_ _--'U coW-;cR-5/500-D48 ±0.2%1±1% --7:::5:-m'cV--;-p"--c..p-----:7;;5°;:;Yo-----'+=-:0~.2% / +1% 75 mV pop 75 mVp-p 75 mV pop 82% ±0.2% / ±1% B~R-12/105-0~ _ _ BWR-12/12S-012 BWR-12/12S-048 ---:7c05°:-;Yo_ _--'±"'0"'.2"%,,I...±,,1.:.:%'--_ _--:B':'W=R-1S/l00-01~ 82% ±0.2% / ±1% BWR-15/10D-048 PS-1 WIDE INPUT RANGE DC/DC CONVERTERS INPUT OUTPUT NO lOAO/FUlllOAO INPUT CURRENT 9-16V de 5V dc, 3000 mA 9-16V de 9-16V de 12V dc, 1250 rnA 15V dc, 1000 rnA 30mA/1600mA 30 mA 11600 mA 9-16Vde 9-16V de 5V dc, 5000 mA 12V dc, 2500 rnA 30 mA 12800 mA 30 mA / 3200 mA 9-16V de 15V dc, 2000 mA 30 mA I 3200 mA 16-36V de 16-36V de 18-36Vdc 5V dc, 3000 mA 12V dc, 1250 mA 15Vde, 1000mA 20 mAl 78DmA lINEllOAD REGULATION 0.02% 11.0% 0.02%/1.0% 0.02% 11.0% 0.02%/1.0% 0.02% /1.0% 20mA/B10mA _._ 20mAI1350mA 0.02%/1.0% 0.02%/1.0% 0.02%/1.0% 20 mA1780 mA 5V dc, 5000 mA 12V dc, 2500 mA 18-36V de 15V dc, 2000 mA 20 mA 11550 mA 20 mA I 1550 mA 0.02% 11.0% 9-18Vdc ±12Vdc, ±625mA 25mA/1520mA 0.02% 11.0% 9-18Vdc 9-16Vdc ±15Vdc, ±50DmA ±12Vdc, ±1250mA 9-18Vde 18-36Vdc 18-36Vdc 18-36Vdc 16-36Vdc 9-18Vdc 9-18Vdc 9-18Vdc 18-36Vdc 18-36Vdc 16-36Vde ±15Vde, ±1000mA ±12Vdc, ±15Vdc, ±12Vdc, ±15Vdc, ±625mA ±500mA ±1250mA ±lDOOmA +5i±12Vdc.1500/±310mA +5/±15Vdc,1500/±250mA +S/+12/-5Vdc, 1500/+310/500mA +5/±12Vdc, 1500/±310rnA +5/±15Vdc, 1500/±250mA +51+121-5Vde, 15001+3101500mA 25mA/l~?_Q._~~_ 0.02% (1.0% 25 mAl 3050mA 25 mAl 3050mA 25 mAl 750mA 0.02% 11.0% 0.02%/1.0% 0.02% J 1.0% 25 mAl 750mA 0.02% 11.0% 2~~J1500mA 25mA/1500mA 50 rnA I 1600 rnA 50mA/1600mA SQmA/1470mA 40 mAl 780 mA 40 mAl 780 rnA 40mAI715m-i\' __ UP5-121125G-D12 UP5-1511GOO-D12 UPS-5/5000~D12 UP5-1212500-D12 UPS-151200G-D12 ~: ~~--c~,,::s.=5-cc~":21"'1"'2~=~"~D=2::-:4:--~~60% 77% 60% UP5-15/1000-D24 UPS-5ISOOG-D24 UP5-121250G-D24 80% 82% 62% UPS-15/2000-D24 BP5-12/625-012 82% 84% 84% BPS-1S1SOO-D12 BPS-15J1000-012 BP5-12/625-024 BPS-15/50o-024 -"6,,-4%,,,0~~---:B,,:P:=5-c:l=21,-,1=2SO:=...:-D:.:2:.:4~~~~ 1.0% 15.00/0 1.0% I 5.0% 84% 78% 78% BPS-1511 000-024 TP5-5J150a-12/310-D12 TPS-5J150a-1S/250-D12 80% TP5-51150a-12/310-024 ---=78"'0;'::'0~----::T:::P5-::-C:1213=1"'0--:5:=ll:=500~-D=-1":2'---- 1.0% 15.0% 1.0% 1 5.0% ---·1.0D/~7~6%-- 76% 78% -'6"'2-"%'---_---'B..,P--'5-,,1~21'_'1C":25G-=D"_1~2'___~~_ 0.02% 11.0% 0.02% 11.0% 1.0% I 5.0% UP5-513000-012 78% 0.02%/ ~o% ---- MOOEl 75% 75% J8% ~_ ~~~~~_~,_Oo_yo~~_ -----~---- 16-36V de 16-36V de EFFICIENCY - -- --'6=0"'%'--_----cT"'P"'5-5I'-==1-:5c.00"'-1=-:5Ic:2=:5=0--=D=24-c-~_ 80% TP5-12131a-511500-024 MINIATURE DC/DC CONVERTERS NO lOADIFUlllOAD lINEllOAD REGULATION INPUT OUTPUT 5Vde 12V dc, 80 rnA 90 rnA/380 rnA 5Vde 15V dc, 65 rnA ±12V dc, ±40 rnA 90 rnA/380 rnA 90 mA/3BO rnA 0.3%/0.4% 0.3%/0.4% 0.3%/0.4% ±15V dc, ±33 rnA 90 mAI380 mA 0:30/;/0.4% 5Vde 5Vdc INPUT CURRENT OUTPUT NOISE REFLECTED ISOLATION & RIPPLE (MAX)' RIPPLE VOLTAGE MIN 20 mV pop 300V de UP5-12180-D5 20 mV pop 15mAp-p 15 mAp-p 2!l.mVp-p 20 mV p-p 15mAp-p --1-5mAp-p 30nV de 300V de UPS-15IS5-D5 BPS-12140-D5 BPS-15133-D5 300V de MODEL NOTE 1. 15iJF capacitor across each output. PLUG-IN ADAPTERS OUTPUT VOLTAGE 4.8 RATED OUTPUT CURRENT LINE/lOAD REGULATION OUTPUT RIPPLE (MAX) MODEL to 5.3V de 11.5 to 12.5V de PS-2 DATEL, Inc_ 11 Cabot Boulevard, Mansfield, MA 02048-1194fTEL (508) 339-3000fTLX 174388/FAX (508) 339-6356 1W - 10W DC/DC CONVERTERS INPUT 12V 28V 5V 5V 12V 5V 12V 5V 12V 26V 5V 28V 12V 5V OUTPUT NO LOAD/FULL LOAD REGULATION 5V,200 rnA 5V,200 rnA 12V,80 mA 24V,40 rnA 24V,40 rnA 2BV,25 rnA 28V,25 rnA 5V,600 mA 5V,600 rnA 5V,600 rnA 12V.250 rnA 12V.250 rnA 24V, 125 rnA 2BV, 100 rnA 100 rnA 1220 rnA 40 rnA / 100 rnA 220 mA 1500 mA 220 rnA 1500 rnA 95 rnA 1210 rnA 160 rnA 1400 rnA 80 rnA /180 rnA 125 mA 1935 mA 50 mA',t364 rnA 20 rnA 1135 rnA 140 rnA IB63 rnA 25 rnA 1125 rnA 125 rnA 1530 rnA 300 rnA 11350 rnA LlNE/LOAD REGULATION 0.05% I 0.1% 0.05% I 0.1% 0.05% 1 0.05%. 0.05%/0.05% 0.05%/0.05% 0.05%/0.05% 0.05% I 0.05% 0.02%/0.04% 0.02% I 0.04% 0.02% / 0.04% 0.02% I 0.04% 0.02% I 0.04% 0.05% I 0.05% 0.05% I 0.05% TEMP. COEF. 0.02% I °C 0.02% I "C 0.02%/"C 0.02% / °C 0.02% I °C 0.02% I °C 0.02% I ~C 0.02% I"C O,Q2% I °C 0.02% I °C 0.02%/ C 0.02% I "C 0.02%1 ~C 0.02%/OC O OUTPUT NOISE & RIPPLE (MAX) 20 20 20 20 20 20 20 50 50 50 50 50 20 20 mV pop mV pop mV p.p mV pop mV pop mV pop mV pop mV P'p mV pop mV p-p mV p-p mV p-p mV p-p mV p-p REFLECTED RIPPLE MAX 1 V rnA pop 5 rnA pop 25 mA p.p 25 rnA pop 10 rnA pop 20 rnA pop 9 rnA pop 32 mA p.p 24 rnA pop 21 rnA p-p 31 rnA p-p 21 rnA p-p 26 rnA p-p 67 rnA p-p MODEL UPM~5J200-D12 UPM-SI200-D28 UPM·12180·DS UPM-24140-0S UPM-24/40-D12 UPM-28J25-D5 UPM-28/25-D12 UP5-5I600-D5 UPS.51600-012 UPSo5l60D-028 UPS~121250-D5 UPS·121250-028 UPM·24/125·012 UPM-281100-DS ~12~V~~2~6~V,~1~00~m~A~--~1~25~m~A~/5~0~0~m~A~_--~0~.0~5"~~~/~0.~05~%~.__~0.~02~%7.~/o~C~--~20mV~p~.p~--~2~5~m~A~P~·P~__~U~PM~.~2~W~100~.D~1~2~ 12V 5V, 1000 rnA 24V 5V. 1000 rnA 26V 5V, 1000 mA 5V 12V,470rnA 24V 12V.470 rnA 5V 24V,210 rnA 12V 24V,210 rnA 24V 5V,2000mA 2BV 5V,2000 rnA 5V, 2000 mA 48V 5V ±12V, ±25 mA 12V ±12V.±25mA 2BV ±12V.±25rnA 5V.t15V,±25rnA 12V ±15V.±25mA 50 mA 1640 rnA 25 mA 1320 rnA 20 mA /275 mA 500rnA/2000mA 120 mA 1415 rnA 500 rnA /2000 rnA 200 mA 1830 rnA 45 rnA/640 mA 40 rnA 1550 rnA 20 mA 1320 mA 150 mA /350 mA 80 mA/165 rnA 30 mA/65 mA 160 rnA 1400 rnA 80mA/BOmA 0.02% 1 0.04% 0.02% 1 0.04% 0.02% 1 0.04% 0.02%/0.04% 0.02% I 0.04% 0.05% 1 0.01% 0.05%/0.01% 0.02%10.05% 0.02%/0.05% 0.02"" 1 0.05% 0.05% 1 0.05% 0.05%/0.05% 0.05%/0.05% 0.05%/0.05% 0.05%/0.05% 0.02% 1°C 0.02%1 "C 0.02%/"C 0.02%/ O C 0.02% rc 0.02% 1 °C 0.02% 1 °C 0.02%/OC 0.02% I °C 0.02% I"C 0.02% I"C 0.02%/ O C 0.02%/ C 0.02%/ OC 0.02%/ C O C 50 mV p-p 50 mV p-p 50 mV p.p SOrnVp-p 50 mV p-p 50 mV p-p 50 mV p-p 50 mVp-p 50 mV pop 50 mV p.p 20 mV p.p 20mVp-p 20rnVp-p 20 rnVp-p 20mVp-p 54 mA p-p 22 rnA p-p 22 mA p.p 61mAp-p 26 mA p-p 100 mA p-p 42 rnA p-p 32 rnA p-p 33 rnA p-p 32 mA p-p 17 mA p.p 8mAp-p 3mAp-p 20 rnA p-p 9mAp-p UPSo511000-D12 UPS~5Il000-D24 UPS·5/1000·D26 UPS~121470-0S UPS~121470-024 UPM-24121()..05 UPM-24121Q-D12 UP~OOO-024 Ups..5/2000-028 UPS·5120OQ..D48 BPM-12125·D5 BPM-12125-D12 BPM-12125-D28 BPM-1S/25-DS BPM-1S/25-D12 _2~8~V__~±~1~5~V,~±~2~5~m~A~__~30~m~A~/8~0~m~A~__~0~.0~5%~/~0.~05~%~.__~0~.0~2%~/~"C~___2~0~m~V.~p·EP____~4~m~A~p~·p~__B~P~M~.~15~/2~5~·D~2~8~ 5V 12V 28V ±12V.±125mA ±12V.±125mA ±12V,±125mA 5V ±15V.±100mA 12V 28V 5V 24V 130rnA/965mA 55mA/380mA 25 rnA 1145 rnA 135 rnA 1955 mA 0.02%/0.02% 0.02%/0.02% 0.02%/0.02% 0.02%/0.02% O.Ol%/ C C O.Ol%JoC O.Ol%/ O C O.Ol%/ C O 35mVp-p 35mVp-p 35mVp-p 34 rnA p-p 23 rnA p-p 21rnAp-p BPS-121125-D5 35mVp-p 33 rnA p-p BPS·1511DO-OS BPS~12/125-D12 BPs..12/125-D28 ±15V .",±,-,1",00,-,m",A:o...__~5",5~m",Ao./3=76,-,m",A"-__~0.,,,02'l,-,v.,,-.1,-,0~.0,",2%",.,---"0,,.0,,1%-""~/~"C~___3,,,5~m~V'-".p·EP____-=2::.4~m~A~pc.t·p~__B~P,-,S"·1,.,5",/1",OO,,·,,,D,,12,,-±15V. ± 100 mA 25 mA /143 rnA 0.02% I 0.02% 0.01%1 "C 35 mV p-p 21 mA p-p BPS-15Jl00-028 ±15V, ± 150 mA 450 rnA /1750 rnA 0.05% I 0.05% 0.005%/OC 25 mV p-p 87 rnA p-p BPM·1S/1S()"OS ±15V,+150mA BOrnA 1350 rnA 0.05%/0.05% O.005%I"C 25 rnVp-p 18 rnA p-p BPM-1S/150-024 -=26~V~~±1~5~V~,±~1~5~0~m~A,----~7~0~m~A~/3~0~0~m~A,----~0~.0~5~%,,/~0~.05~o/.~. ___0~.~00~5~%~/="C~. __~2~5~m~V~p~.p,--__-1=5,-,m~A~p~.~p ___B=P=M~.~15~/1=~~.D~2~8__ 5V +12V, +230 mA 130 rnA 11650 rnA 0.02% 1 0.02% 0.01% I °C 35 mV p-p 58 rnA p-p BPS-12J230-0S -"12:cV~-"-±1::2,,V,-,,+=-2"03",0_"m:cA~____5",5~m-::AC'./6",9",0_"m:cA__ "'0.... 02c:·;.:..1'-'0~.0--:2"'%___-"0".0'-'1"-"V"c./~"C::-___3"'5~m~V:Lp·EP____-=2c.4~m~A... p~.p,--__B=P=-S:'12/230.D12 0.02% 1 0.02% 0.01% 1 °C 35 mV p-p 24 rnA p-p BPS-121230-D24 ±12V, +230 rnA'--__-=2c"C5~m-::A"/3"'0"'0_"m"'A~___'0,,.O..,2"'%~/.,,0.~02"..o/."'.___0~._.01'-'";.:."Ic.".-;C____-'"3"5-"m,,V,.tp'!·p_____--'2"'3'-'m"'ACJP"-·"-p__--=B"'PS,,·-'1,,21~23",Ooc·D~2",8 ±15V,±190mA 135 mA/1700 rnA 0.02%10.02% O.Ol%/OC 35mVp-p 60 rnA p-p BPS-15/190-DS ±15V, ± 190 rnA 55 rnA 1710 rnA 0.02<'10 1 0.02% 0.01% 1 °C 35 mV p-p 25 rnA p-p BPS-1S/190-D12 24V ±12V, ±230 rnA 25 mA 1340 rnA 28V 5V 12V 24V ±15V'-',±~1=9~0~m~A~--~3~0~m~A~/3=5~0~m~A'----~0=.0=2%=.~/~0.~02=o/.7.---0~.0~1=O/'~./~"~C----~3~5~m~V~p~.p~---2=5~m~A~p~·~P--~B~P~S'~1~~~19=O~.D=2=4-- --,,26~V~~±1=5~V~,±~1~9~0~m~A'----~2':-5~m~A~/3~0::'0~m~A'----~0=.0::'2%~.":/~0.~02~o/.7.___0~.0=_1~%:c/,-;"~C----~3~5~m~V~p~·Pc.. 48V ±15V,+190mA 14mA/180mA 0.02%/0.02% O.Ol%/OC 35 mVp-p 5V ±12V. ±420 rnA 980 rnA 14000 rnA 0.05% I 0.05% 0.02% I °C 50 mV p-p 12V +12V, +420 rnA 340 rnA 11530 rnA 0.05% 1 0.05% 0.02% 1 °C 50 mV p-p 24V 28V 5V .t12V, +420 rnA ±12V, + 420 rnA ±15V, +412 rnA 175 rnA 1760 rnA 130 rnA 1650 rnA 260 mA 13700 rnA 0.05% 1 0.05% 0.05% 1 0.05% 0.02% I 0.02% 0.02% 1 cC 0.02% I °C 0.01% I °C 50 mV p-p 50 mV p-p 35 mV p-p 24 rnA p-p 25mAp-p 120 rnA p-p 46 mA p-p 23 rnA p-p 20 rnA p-p 130 rnA p-p BPS-1S/190-02B BPS·151190-D4B BPM-12/420·DS BPM-12/420-012 BPM-12/420-D24 BPM-12/42()"028 BPS~lS/412-DS ---:e12"V,---=.+1",5"V,-"+o:4"'1"'2"'m"'A'--__1c:1-,oo"m"'Acc/l::5"'9_.0"'m"'A__-"O".O"'2'l"'V."/O"'.O"'2%:"'-___O,c.:'-Ol"o/."'.1c.""'C____ 35 mV p-p'--__~5"'4"'m"'A'-'p"'·p'-__"B"PS,_:.,,1:5I412-D12 ~24=V~~±1=5~V~,±~4=1~2~m~A'----~5~5~m~A~/7=7~0~m~A'----~0=.0=2'l=~":/~0.~02=o/.~"---0~.~01=%~./~"~C----~3~5~m~V~p~·P~--~3=6~mA~p.~p--~B=P=S~.1=5~~~12~.~D2=4c-28V ±15V,±412mA 45mA/660rnA For Immediate Assistance, Dial 1·800-233-2765 0.02%/0.02% O.Ol%/OC 35mVp-p 39 rnA p-p BPS-1S/412-02B PS-3 1W -10W AC/DC SUPPLIES OUTPUT RATED OUTPUT VOLTAGE LINE LOAD OUTPUT OUTPUT VOLTAGE CURRENT ACCURACY REGULATION REGULATION RIPPLE (MAX) IMPEDANCE 5V de 250 rnA 1.0% 0.05% 0.1% 1 mV RMS _ _ _-"°:.:.°::5'::c,_____ U.:,P:::M-=-S,,12::50=-_ __ 5V de 5V de 500 rnA 1000 rnA 1.0% 1.0% 0.05% 0.05% 0.1% 0.1% 1 mV RMS 1 mV RMS o.osn ~~~~ :~ ~:~~: ~.~:~ ~:~!:o ~ ~~ ~~~ ~:~~c::~''-n----'~~:=:"-:5=S;='~~~~7~B=---- :~ :~ a.01U MODEL UPM-5/500 UPM-5/1000 ±250 rnA 1.0% 0:05°/: ----='0.C-p=y,------C O.OSH BPM·5/250 1 mV RMS ±SOO m-A:----c1"".0:;c%'------.::0.-.::05"''''O-,-------;0'"'.1c;'I<7-,- - - - : - 1cc mC;VCOR ;7M"'SC------O: O."'03""""'-- BPM-5/500 ±5V de ±5V de 0.02% 0.05% 2mVRMS D.l0n ___ ±c.:12:cV--'d::cc_ _---"±=2~00"'m"'A"----lc:.O:c%=-----::O.02% ±15V de ±60 rnA 1.0% 0.02% +12Vdc ±100mA 0.05% 0.05% 2 mV RMS 2 mV RMS o.osn O.20n BPM-12/200 BPM·15/60 +10Dm"'A,:-_ _.-:.1.0% ___~~g~?. ___. 0.05% 2mVRMS ±20Q rnA 1.0% 0.02% 0.05% 2 mV RMS -----------------1.0% 0.02% 0.05% 2 mV RMS ±300 mA a.l0n O.OSn. 0.03n BPM·15/100 BPM·15/200 BPM-15/300 ±15Vdc ±15V de +15V de ±12/5V de 2.0% BPM-12/10D ±100 /500 mA ~2/5V dc___±150 !...!QOO mA __ .._._~~~.~.~ 0.02% I 0.OM~~__ ~2.5% / 0.1% +15/5Vde ±100/S00mA ±15/5V de _~.~OOO rnA 0.02%/0.05% 1.0% 0.05%/0.1% ~ mV ~~~:!Q / O.OSU __ ._ .. _~~~~.2~~~-5/1000 2mV/l mVRMS 0.10 I O.OS!:l __~~I~==-~.==~~-oJ}2~lo7o.05~~·_.~-OJ>50/o / 0.1%~--2mv/l mV R·MS-O~/-O.05Q TPM-15/100-5/500 -TPM~~5I150~5!~O~ __ CHASSIS MOUNT AC/DC SUPPLIES RATED OUTPUT CURRENT VOLTAGE LlNEILOAD OUTPUT OUTPUT VOLTAGE ACCURACY REGULATION RIPPLE (MAX) IMPEDANCE 5Vde 250mA 1.0% 0.05% I 0.1% 1 mV poop 0.Q5n 5Vde SOOmA 1.0% 0"'.0"'5"'%:.:1.::0:.:_1"'%'---_---'-1"'m'-'v-"p--'_p'---_-_-_---::-.::0--::.-.::0-=:5;c;l~'--·UiCM-SISOO 0.05% / 0.1% 1 mV poop O.OH} UCM-5/1000 0.05%/0.1% 1 mVp-p -'-'-M~-tJCM:5!2000 OUTPUT ------5Vde - . _ - - - - - -1000 - -mA - - - - - -1.0% 5V de 2000 mA 1.0% ±15V de ±60mA 1.0% ----=~c_7'----=="--------""~---=0"'-0:::2,,%'-'I.::O-:::05::,'I<:::,--=-2 ",m""Vpoop ±15V de ±15V de +200 rnA ±15V de ±300 mA ±100 mA ----------- . 0.20Q MODEL UCM-5f250 ------ BCM-15/60 BCM-15/100 _. ____ ._ .._.._ 1.0% __ ___ ~q2%/0.05~. _ _2_mVp-p ___ ~!.9~! ..___ 1.0% .. _~?~LQ.05o/~ _ _ ~~__ 0.05n BCM-15/200' 2 mV poop 0_05<> _ _ _B_C_M_-_1S_13_00 _ _ _ _ _ _ __ 1.0% 0.02% I 0.05% HIGH EFFICIENCY AC/DC SUPPLIES OUTPUT OUTPUT VOLTAGE RATED OUTPUT CURRENT VOLTAGE ACCURACY LINE/lOAD REGULATION OUTPUT RIPPLE (MAX) IMPEDANCE 5Vde 5Vde 5000 rnA 5000 mA 80% 80% 0.05%/0.1% 50 mV pop 50 mV poop 0_002<> 0_002<> 0.05%1o_1% MODEL USM-5IS _ USC-SIS HIGH VOLTAGE MODULES OUTPUT RATED OUTPUT VOLTAGE LINE/LOAD OUTPUT OUTPUT VOLTAGE CURRENT ACCURACY REGULATION RIPPLE (MAX) IMPEDANCE 0.05%/0.2% 0.05%/0.2% 10 mVRMS 10mVRMS s.on BPM-12012S 5.0n BPM-1S0120 0.05%/0.2% 10 rnVRMS 5.0n BPM-180116 ±120Vde _ _ _ 25mA PS-4 ±150V de 20 mA 1.0% 1.0% +180V de l6mA 1.0% MODEL DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194fTEL (508) 339-3000fTLX 174388/FAX (508) 339-6356 VOLTAGE CALIBRATORS MODEL OUTPUT RANGE SETTABLE INCREMENTS ACCURACY SOURCEISINK CURRENT DISPLAY POWER CASEI MOUNTING DVC-350A ± 1.2000 or ±12.000 100 fJoV or 1 rnV 0.015% 20 rnA 41/2 DIGIT LCD 9V Battery or 115VAC Adaptor (optional) 5.75 X 3.60 X 1.29 in (146 X 91 X 33 rnrn) HAND HELD DVC-8500 ±19.999 1 rnV 0.005% 25 rnA 41/2 DIGIT MECHANICAL 100 VAC (J) 115 VAC (A) 230 VAC (E) 5.59 X 2.11 X 5.78 (142 X 54 X 147 rnrn) For Immediate Assistance. Dial 1-800-233-2765 DVC-1 DIGITAL PANEL METERS Model 3.5 Digit LED 4.5 Digit LED 3.5 Digit LCD 4.5 Digit LCD Other Digital Panel Products Power Std. Input Case Features OM-3l00l-l +5Vdc ±2Vdc B DM3l00N-l +5Vdc ±2Vdc A Short Depth Case Provisions for 4-20 mA input DM-3l0l·l +5Vdc j;2Vdc A High Intensity Display OM3l03-l +5Vdc ±2Vdc B High Intensity Display OM-3l-l +5Vdc ±2Vdc OM-3l00B-l 1151230VAC ±2Vdc B Short Depth Case OM3l04-l 1t51230VAC ±2Vdc B High Intensity Display OM-9llS-l 1t51230VAC ±2Vdc C NEMA 12 (Vibration Std) OM-4l01N-l +SVdc ±2Vdc A High Intensity Display OM-9200-l +SVdc ±2Vdc C NEMA 12 (Vibration Standard) OM-4l00D-l +SVdc ±2Vdc A High Speed Sampling SeriallParallelBCD Output low Cost· Uncased OM-4l01D-l +SVdc ±2Vdc A High Intensity Display SeriaVParaliel BCD Output OM-4l0ll-l +SVdc ±2Vdc B Serial BCD Output OM-4200-l +5Vdc ±2Vdc A Serial BCD Output OM-921S-l ll51230VAC ±2Vdc C NEMA 12 (Vibration) OM-3l00U-l +519Vdc ±2Vdc A Units Display (Batt. Pwr.) OM-3l00X-l +519Vdc ±2Vdc B Battery Powered OM-3l02A +SVdc ±2Vdc A OM-lX3-l +SVdc ±2Vdc OM-3l00U2 1l5VAC ±2Vdc A Units Display OM-4l05-l +5Vdc ±2Vdc A Serial BCD OUT (Batt. Pwr.) Adjustable A 20 Segment LED Bar Graph wi TTL Outputs B 10 MHz CounterlTimer OBM-20 +5Vdc PG-6 +5Vdc Units Display Autoranging (200 mV • 200V) Low Cost - Uncased NOTE: Input range kits are available for all OM·31 00, 4100, and 9000 Series DPMs DPM-1 DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1l94ITEL (508) 339-3000rrLX174388/FAX (508) 339-6356 3.5 DIGIT, MINIATURE VOLTAGE METERS Power Std. Input Case OMH-30PC-O +5Vdc ±200 mV E OMH-30PC-l +5Vdc ±2Vdc E Encapsulated (Plastic). 24-pin DDIP OMH-30PC-2 +5Vdc ±20Vdc +5Vdc ±200mV __.- E Encapsulated (Plastic). 24-pin DDIP OMH-30MM-O OMH-30MM-l +5Vdc ±2Vdc E OMH-30MM-2 +5Vdc ±20Vdc E OMS-30PC-O-RL +5Vdc ±200mV F OMS-30PC-I-RL +5Vdc ±2Vdc F Model NEW Self-Contained 3.5 Digit LED Ultra-Miniature NEW Self-Contained Single-Piece 3.5 Digit LED ---._------" -- ..- ._---- -._--- _._-- - - - - - - _ .. +5Vdc ±20Vdc F +5Vdc ±200mV F OMS-30PC-I-RS +5Vdc ±2Vdc F OMS-30PC-2-RS +5Vdc ±20Vdc F OMS-30PC-O-RH +5Vdc ±200mV F OMS-30PC-I-RH +5Vdc ±2Vdc F ±20Vdc ±200mV F F --- OMS-30':;P~C~-:;-I-~G:;-L---+-;5;;V;cd-c--- ±2Vdc OMS-30PC-2-GL ±20Vdc --:~--:--~C--C-:------C-'------:- F F +5Vdc ±200mV OMS-30PC-I-GS +5Vdc ±2Vdc F +5Vdc ±20Vdc F OMS-30Pe-O-BS F - -+5Vdc - - - -±200mV ----F ----------- OMS-30PC-I-BS +5Vdc ±2Vdc F OMS-30PC-2-BS +5Vdc ±20Vdc F OMs-30PC-O-YS +5Vdc ±200mV F OMS-30Pe-I-YS +5Vdc ±2Vdc F OMS-30PC-2-YS OMS-30PC-O-OH OMS-30PC-I-OH +5Vdc ±20Vdc F +5Vdc ±200mV F 7 -+-=5""V;-:dc----±-=-2V'"'dc - - - - = F --- OMs-30PC-2-0H +5Vdc ±20Vdc ----------- .-~--- ..- Hermetically Sealed, Quartz window, Ceramic 24·pin DDIP. MIL-D-87157 Temperature Range Sealed. Plastic Case. Low Intensity RED Display Sealed, Plastic Case, Standard Intensity RED DISPLAY Sealed, Plastic Case, High Intensity RED DISPLAY -----------Sealed, Plastic Case, Low Intensity GREEN DISPLAY --------------- OMS-30PC-O-GS OMS-30PC-2-GS .. --- -------.--------~- OMS-30PC-2-RL +5Vdc -_ E OMS-30PC-O-RS OMS-30PC-2-RH +5Vdc -OMS-30P:;OC-;-O'"'-G"'L---+5Vdc Features Encapsulated (Plastic). 24-pin DDIP F Sealed, Plastic Case, Standard Intensity GREEN DISPLAY Sealed, Plastic Case, Standard Intensity BLUE DISPLAY Sealed, Plastic Case, Standard Intensity YELLOW DISPLAY Sealed. Plastic Case, High Intensity ORANGE DISPLAY CASE SIZES A 2.53'W x 3.34"0 x 0.94"H (64 x 85 x 24 mm) B 3.00"W x 2.15"0 x 1.76"H (76 x 55 x 45 mm) C 3.60"W x 3.57"0 x 1.67"H (91 x 91 x 42 mm) o 1.89"W x 1.22:0 x 0.94"H (48 x 31 x 24 mm) E 1.29"W x 0.25"0 x 0.80"H (33 x 6 x 20 mm) f 2.19"W x 0.54"0 x 0.95"H (55 x 14 x 24 mm) For Immediate Assistance, Dial 1-800-233-2765 DPM-2 PROCESS MONITORS/CONTROLLERS DATEL designs and manufactures a complete line of Process Monitors/Controllers supporting Thermocouples, RTDs, Strain Gages, and Voltage/Current signal inputs. These low cost units contain such features as built-in RS232 serial port (RS-422/485 optional), user-selectable setpoint outputs (up to 4 discrete and 1 optional Analog), built-in configuration and setup command set, fully isolated inputs (to 1500 Volts, typ.) and a six-character, 14-segment vacuum fluorescent display (blue-green). Each model may be configured and operated from either the front panel or via the serial port. For reliability, accuracy, and low price, DATEL's PM-5000 series Process Monitors/Controllers are simply the best. PM-50 o 0-1 INPUTS Thermocouple types J, K, T, S, B, E, N,R RTDlThermistor Strain Gage Voltage/Current 5 6 7_ 8 COMMUNICATIONS MODE RS-232-C (Standard) RS-422/485 o ANALOG INPUT o None One output (0 - 10V/4-20 mAl A E J D PM-1 POWER 115 VAC 230 VAC 100VAC ±5 Vdc DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194ITEL (508) 339-3000ITLX 174388/FAX (508) 339-6356 PANEL MOUNT THERMAL PRINTERS Model Columns Input Power Interface (Note 1) Character Set BCD 115/230 VAC Numeric (decimal or hex) plus sign DPP-Q7 Case Special Features A Simple DATEL DPM interface APP-20A1 20 Parallel 115/230 VAC 96 char ASCII A Inverted, tall character options APP-20D1 20 Parallel +12 Vdc 96 char ASCII A Inverted, tall character options 115/230 VAC 96 char ASCII A RS-232/20 mA loop +12 Vdc 96 char ASCII A Inverted, tall, condensed character options IEEE-488 115/230 VAC 96 char ASCII A Inverted, tall character options 115VAC 127 char ASCII A -----~------.--- _A_P_P_-A_2_0_A_2_1_ _ _ 2_0_ _ RS-232/20 mA loop APP-A20D21 APP-20A3 20 20 ---~--- ._--------------- .----------------------.... _--- ---- MPP-20A 20 RS-232/Parallel MPP-20D 20 RS-232/Parallel +12 Vdc 127 char ASCII A MPP-20E 20 RS-232/Parallel 230 VAC 127 char ASCII A APP-48Al 48 Parallel 115 VAC 192 char ASCII B APP-48A2 48 RS-232 115/230 VAC 192 char ASCII B Inverted character options APP-48D2 48 RS-232 +12 Vdc 192 char ASCII B Inverted character options 115/230 VAC 192 char ASCII B Inverted character options +12 Vdc 192 char ASCII B Inverted character options 115/230 VAC 96 char ASCII C ------.-~- ... Inverted, tall, enhanced character options - - - - - - - - - - - - - - - - - - - - - - - - - - - _.. Inverted character options ---_.__._-----------_._-------------------_._--------------------- APP-48A3 48 APP-48D3 48 IEEE-488 IEEE-488 APP-M20A1 20 Parallel ---------- RS-232 APP-M20A21 20 115/230 VAC 96 char ASCII _ _-::C__ Hardened for shock, vibration cc2:c:O-=D-=2-:-1---::-------:::::-c=--------,-c-:-c-c-------,9cc-=A-=P-=P-=_M 6 char ASCII RS-232 C and humidity (mobile) 20 +12 Vdc NEW GPP-42 48 Parallel +12 Vdc D 48 RS-232 +12 Vdc D 42 SerialiParaliel 115/230 VAC (50/60 Hz) 256 char ASCII E 8 International Character Sets High Res Graphics, 200 Line Buffer CUSTOM CHARACTERS AVAILABLE NOTE 1. 100 VAC versions available for most models ("J" version); European line cords also available ("E" version). Consult factory. CASES A =4.44"W x 2,76"H x 8.00"D B = 8.20"W x 2.84"H x 8.14"D C = 5.36"W x 3.74"H x 8.00"D (Including mobile-mount brackets) D = 9.25"W x 3.25"H x 10.44"D (Including mobile-mount brackets) E = 8.20"W x 2.84"H x 10.50"D For Immediate Assistance, Dial 1-800-233-2765 TP-1 MULTIBUS I BOARDS Model ST-702 AID Channels AID Resolution 80 Isolated I KV 13 Bits AID Speed PGA 33ms x50, xlOO In/Out Ranges D/A Resolution D/A Channels None 5V Down 10 50 mV Notes Direct thermocouple connections, on board linearize and CJC ST-711 ST-732 32S/16D ST-703 20 ~s 5V,IOV Down to 50 mV 2 (732) 12 Bits On board start timer, Interrupt None 2.5V to 10V 41020mA 41solaled 12 Bits 350V Isolation per channel ST-724 None 5V,IOV 41020mA 4 12 Bits ST-728 None 5V,IOV 41020mA 40r8 12 Bits 5V,IOV 40r8 16 Bits 4V Down 10 20 mV None ST-716 None ST-705 80 ST-519 TTL discrete I/O 12 Bits 13 Bits 33 ms xl to xl K Software xl to x200 RS-232 subsystem and CPU, Direct thermocouple connection, linearize, CJC TTL 72 TTL lines, In/Out, Interrupt PCI AT AID-DIA BOARDS Model PC·414A 4 SE w/simul sampling AID Resolution AID Speed Prog. Gain Amplifier In/Out Ranges D/A D/A Channels Resolution xlorxlO 5V,IOV, IV 12 Bits 12 Bits 1.5 MHz 500 KHz 5V,IOV 12 Bils Notes 4K-sample FIFO memory, analog trigger, parallel data port, counter/timer, DMA Veclored interrupl PC·414B 4SE 14 Bits PC-414C 4SE 12 Bits I MHz 5V,IOV 12 Bits PC-414D I SE 12 Bits 4 MHz tv 12 Bits PC·414E 16SE 12 Bits 400 KHz 10Vto 100 mV 12 Bits PC-430A 4SEw/simul sampling 12 Bits 1.5MHz PC-430B 4SE 14 Bits 500 KHz 5V,IOV None Local 32 MHZ 320C30 DSP, 512K memory,DMA Fast "no prgmg" PC-43OC 4SE 12 Bits I MHz 5V,IOV None command executive, PC-430D I SE 12 Bits 4 MHz tv None 16SE 12 Bits 400 KHz PC·430E PC-462 IIOB-1 A/D Channels 4 Monitor Channels 12 Bits 25 KHz xl to xlOO xl or xlO xl to xlOO 5V,IOV, tv None 10Vto 100 mV None o to ±15V or5V, lOW 2 Isolated, Vor I mode DSP library, Vectored interrupt 12 Bits Programmable power DAC DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194fTEL (508) 339-3000fTLX 174388/FAX (508) 339-6356 VMEBUS AID - DIA BOARDS Model AID Channels DVME-601A DVME-601B DVME-601C DVME-601D 16S/8 D Expandable t02S6 AID AID Resolution Speed 12 Bits 20 3S~s 16 Bits , 12 Bits 2~s 12 Bits 20 ~s DVME-611/612D 32S/16D Expandable t02S6 D/A Resolution x1 tox1K S,10V down to SO mV None _.- 12 Bits 4 16 Bits 3S Notes 68010CPU 2S6Kmemory RS-232, S TTL 1/0 CounterlTimers 400ms DVME-601E DVME-611/612B D/A Channels ~s DVME-611/612A DVME-611/612C InlOut Ranges 4 ~s 12 Bits 16 Bits Prog. Gain Amplifier "No prgmg" Command Exec. Vectored interrupt ~s ~s x1 to x128 Software Pgmble SV,10V down to SO mV x1 tox100 SV,10V down to SO mV 16 Bits 400 ms DVME-611/612E 12 Bits 2 ~s DVME-611/612F 14 Bits 4 ~s DVME-613 16S/8D Isolated 500V 12-14-16 Bits 40 ~s DVME-624 None --- --- --- DVME-626 None --- --- 2 (612) 12 Bits Short 110 SA:16, SD:16 Vectored interrupt 8 In/8 Out TTL, SA:24,SD:16 Start timer, interrupt None --- 2.S to 10V 4t020mA 4 Isolated 12 Bits SA:16,SD:16 3S0V Isolation --- SV,10V 6 16 Bits SA:16,SD:16 8 t2Bits SA:16, SD:16 DVME-628 None --- --- --- 2.S to 10V 4t020mA DVME-641 32 S/16 D SlaveMUX board 6 ~s Settling --- SV,10V 4t020mA --- --- Slave input expander t0601,611,612 DVME-643 8D Isolated SlaveMUX board 2.Sms Settling xSO, x100 SV Down to SO mV --- --- Slave input expander t0601,611,612 16 S/8D SlaveMUX board 6 ~s Settling --- SV,10V --- --- Simultaneous Sample/Hold Expander to 601, 611, 612 DVME-614A 4Simul.S/H 12 Bits 1.SMHz x1 or x10 W, SV, 10V DVME-614B 4S 14 Bits SOO KHz DVME-614C 4S 12 Bits 1 MHz DVME-614D 1S 12 Bits 4MHz DVME-614E 16S 12 Bits 400 KHz x1 to x100 1, S, 10V, 100mV DVME-630A 4Simul. S/H 12 Bits t.S MHz x10rx10 1V, SV, 10V DVME-630B 4S 14 Bits SOO KHz DVME-63OC 4S 12 Bits 1 MHz DVME-630D 1S 12 Bits 4MHz DVME-630E 16S 12 Bits 400 KHz x1 to x100 DVME-622 None --- --- --- DVME-621 None DVME-64S --- For Immediate Assistance, Dial 1-800-233-2765 --- SV,10V --- SV,10V 1 12 Bits Vectored interrupt SV,10V Local 32 MHz 320C30 DSP, S12 K Memory, Fast "no prgmg" command Executive, Interrupt DSPlibrary None --- SV,10V 16Simul. Update 12 Bits 3 SV,10V @100mA or 160mA 4 Isolated 12 Bits or current mode, active SV,10V SV,10V --- Sample counter/timer Simultaneous sampling SV,10V --- 4K-sample FIFO memory Analog trigger Paraliel data port 1, S, 10V, 100mV ~s settling per channel Power DAC's, voltage drivers, SOOV isolation 1/08-2 HIGH-RELIABILITY PROGRAMS DATEL is committed to meeting the demading requirements of military, aerospace, and severe environment applications. Toward that end, DATEL offers several options in its quality program. OPTION 1 - MIL-STD-883 Class H Compliant Devices DATEL Inc. is QUALIFIED by the Defense Electronics Supply Center for the manufacture of selected hybrid microcircuits in FULL COMPLIANCE with Military Specification MIL-H-38534 (Hybrid Microcircuits), FSC 5962, and MIL-STD-1772 SECTION B. The accompanying chart gives a concise overview of MIL-STD-883 screening requirements and their implications for DATEL customers. TEST A-I METHOD PURPOSE Internal Visual (Precap) Method 2017 Eliminates devices with potential for failure under mechanical, electrical, or thermal stress. Stabilization Bake MethQd 1008, Test Condition C, 24 hrs. at 150°C Eliminates device failure due to storage at elevated temperatures. Temperature Cycling Method 1010, Test Condition C, -65 to 150°C Determines resistance of device to sudden exposure to extreme temperature changes. Removes potential failures due to thermal stress on bonds, etc. Constant Acceleration Method 2001, Test Condition A, Y AXIS, 5 kg. Eliminates potential failures due to structural or mechanical weakness not detected in shock or vibration test. Burn-in Test Method 1015, Test Condition B, 160 hrs. at +125 °C Stresses devices at temperature in order to eliminate infant mortality failures. PDA10% Static Tests performed at +25 °C Percent defective allowable - Rejects lots with static test failures greater than 10%. Final Electrical Test Performed at +25 °C and at max. and min. operating temperatures Verifies that device still meets specified data sheet parameters. Seal Fine and Gross Method 1014, Test Condition A (fine), 1 x 10·7 ccl Sec. for volume of ~0.5 to <1.0 cm3 and 5 x 10-8 cclSec. for volume of ~1.0 to <10.0 cm3. Test Condition C (gross) Insures hermeticity of device package. Eliminates degradation due to absorption of water vapor or other contaminants. External Visual Method 2009 Insures that materials, design, construction, marking, and workmanship conform with applicable procurement documentation. DATEL, Inc. 11 Cabot BoUlevard, Mansfield, MA 02048-1194ITEL (508) 339-3000ITLX 174388/FAX (508) 339-6356 MIL-STD-883 compliancy also requires that complete documentation be available to support the product. An analysis of the design along with element and package evaluations are performed to ensure a high quality product. The manufacturing process is also stringently controlled in order to obtain the high quality level. Initial qualification requires passing the MIL-STD-883 test for groups A, B, C, and D. After initial qualification, groups A & B are tested for all lots. Group C is tested initially and to qualify any product changes which may occur. Group 0 testing is also performed initially and at intervals not exceeding 6 months for future lots. MIL·STD·883 PRODUCTS ANALOG·TO-DIGITAL CONVERTERS· MODEL NO. RESOLUTION CONVERSION TIME LlNEARlTY 12 Bits 12 Bits 10 Bits 12 Bits 8 Bits 8 Bits 7 Bits 12 Bits 8f.lSec 20 f.lSec 800 nSec 1 f.lSec 4 nSec 50 nSec 50 nSec 500 KHz ±1/2 LSB ±1/2 LSB ±1/2 LSB ±3/4 LSB ±1/2 LSB ±1.5 LSB ±1 LSB ±3/4 LSB ADC-HZ12B/883B ADC-HX12B/883B ADC-816/883B ADC-511/883B ADC-228/883B ADC-208/883B ADC-207/883B ADS-111/883B DIGITAL-TO-ANALOG CONVERTERS MODEL NO. RESOLUTION SETTLING TIME LINEARITY 12 Bits 16 Bits 12 Bits 12 Bits 10 Bits 8 Bits 31lSec 151lSec 3f.lSec 50 nSec 25 nSec 25 nSec ±1/2 LSB ±2 LSB ±1/2 LSB ±1/2 LSB ±1/2 LSB ±1/2 LSB DAC-HZ12B/883B DAC-HP16B/883B DAC-HK12B/883B DAC-HF12/883B DAC-HF10/883B DAC-HF8/883B DATA ACQUISITION SUBSYSTEMS MODEL NO. RESOLUTION INPUT CHANNELS THROUGHPUT 12 Bits 12 Bits 12 Bits 12 Bits 4 Diff. 8SE 16SE 8 Diff. 75 KHz 75KHz 50KHz 50 KHz HDAS-76/883B HDAS-75/883B HDAS-16/883B HDAS-8/883B MULTIPLEXERS MODEL NO. CHANNELS SETTLING TIME ACCESS TIME MX-826/883B 8SE 200 nSec 70 nSec SAMPLE-AND-HOLD AMPLIFIERS MODEL NO. LINEARITY ACOUISITON TIME BANDWIDTH 0.01% 200 nSec 16.MHz SHM-4860/883B For Immediate Assistance, Dial 1-800-233-2765 A-2 OPTION 2 TEST DATEL QL SCREENING PROGRAM TEST CONDITION PURPOSE Internal Visual (100% Precap) Test Method 2017 Eliminate visual defects prior to seal Stabilization Bake 100% TM 1008,Condition C 24 hours at + 150 DC (Optional if TM 1030 is used) Eliminates failures due to high temp storage Temperature Cycling, 100% TM 1010, Condition C -65 to + 150 DC, 10 cycles Eliminates failures due to mechanical weakness 100% Constant Acceleration TM 2001, Condition A Yl Axis, 5000 G Eliminates failures due to mechanical weakness 100% Burn-in Static burn-in 160 hrs. at +125 DC (Similar to TM 1015 or TM 1030) Eliminates failures due to infant mortality 100% Final Electrical Test Performed at +25 DC, TMIN, and TMAX operating temperatures Verifies that devices meet speicifications over temperature range 100% Fine and Gross Leak Test Method 1014 Condition A (fine) 5 x 10.7 cc/Sec. Condition C (gross) Insures hermeticity for high humidity environments 100% External Visual Test Method 2009 Insures proper marking, construction, workmanship ·QL PRODUCTS SAMPLE-HOLD AMPLIFIERS MODEL NO. SHM-45MM-QL SHM-4860MM-QL SHM-6MM-QL SHM-HUMM-QL LINEARITY ACQUISITION TIME 0.01% 0.01% 0.02% 0.1% 200 nSec. 200 nSec. 2j.!Sec. 25 nSec. HOLD MODE DROOP 0.5 j.!V/j.!Sec. 0.5 j.!V/j.!Sec. 10 j.!V/j.!Sec. 50 j.!V/j.!Sec. OPERATrONAL AMPLIFIERS MODEL NO. AM-500MM-QL AM-1435MM-QL INPUT OFFSET VOLTAGE GAIN BANDWIDTH OUTPUT 3mV 5mV 130 MHz 1000 MHz +10V at 50 mA + 7Vat 14 mA DATA ACQUISITION SUBSYSTEMS MODEL NO. HDAS-16MM-QL A-3 RESOLUTION INPUT CHANNELS THROUGHPUT 12 Bits 16 Single-Ended 50 KHz DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1194ITEL (508) 339-3000ITLX 174388/FAX (508) 339-6356 ANALOG-TO-DIGITAL CONVERTERS MODEL NO. ADC-S17 AMM-QL ADC-HX12BMM-QL ADC-HC12BMM-QL ADC-S15MM-QL ADC-S25MM-QL RESOLUTION CONVERSION TIME LINEARITY 12 Bits 12 Bits 12 Bits S Bits S Bits 2 ~Sec. 20 ~Sec. ± 1 LSB ± 1/2 LSB ± 1/2 LSB ± 1/2 LSB ± 1/2 LSB 300~Sec. 700 nSec. 1 ~Sec. SAMPLING ANALOG-TO-DIGITAL CONVERTERS MODEL NO. ADC-HS12BMM-QL RESOLUTION SPEED LINEARITY 12 Bits 66 KHz ± 112 LSB DIGITAL-TO-ANALOG CONVERTERS MODEL NO. DAC-HP16BMM-QL DAC-HF12BMM-QL DAC-HK12BMM-QL . DAC-HZ12BMM-QL DAC-HF10BMM-QL DAC-HFSBMM-QL For Immediate Assistance. DiaI1-S00-233-2765 RESOLUTION SETILING TIME LINEARITY 16 Bits 12 Bits 12 Bits 12 Bits 10 Bits 10 Bits 15 ~Sec. 50 nSec. 3 ~Sec. 3 ~Sec. 25 nSec. 25 nSec. ±2 LSB ± 1/2 LSB ± 112 LSB ± 1/2 LSB ± 1/2 LSB ± 1/2 LSB A-4 OPTION 3 - 859000 PROGRAM DATEL also has a BS9000 program in compliance with British Standards for high reliability devices. BS9000 is the United Kingdom's national system for the independent inspection approval and surveillance of manufacturers, distributors and test laboratories in the electronic component industry. The accompanying product flow gives an overview of the BS9000 products through screening and quality conformance inspection. 8S9000 Screening Requirements I Production batch formed I I Fine and gross leak tests BS 9400 1.2.6.14 I Screening Level B I Electrical tests at 25°C as per subgroups A1 (a) (1), and A2 I I Pre-cap Inspection BS 9400 1.2.10 Level B ~ High temperature storage BS 9400 1.2.6.3 150°C for 24 hours I I I Rapid change of temperature BS 9400 1.2.6.13 10 cycles -65°C to +150 °C Burn-in Screen BS 9400 1.2.9.2 160 hr. minimum at 125 l Inspection Lot Formed I Sample Test to groups A,B,C as appropriate I I I I Acceleration steady state BS 94001.2.6.9 294000 m/Sec.'direction Y1 859000 PRODUCTS ANALOG·TO·DIGITAL CONVERTERS MODEL NO. ADC-208MM-BS9400-G0140 ADC-303MM-BS9400-G0106 ADC-303JM-BS9400-G0106 Al')C-304MM-B29400-G0177 RESOLUTION 8 8 8 8 BITS BITS BITS BITS CONVERSION TIME LINEARITY 66 riSec 10 nSec 10nSec 50 nSec ±21/2 LSB ±3/4 LSB ±3/4 LSB ±1/2 LSB Parts qualified to the BS9000 specification have a quality level equivalent to MIL-M-38510 giving a quality factor of 1. A-5 DATEL, Inc. 11 Cabot BoUlevard, Mansfield, MA 02048-1194fTEL (508) 339-3000fTLX 174388/FAX (508) 339-6356 DESC STANDARD MILITARY DRAWING PROGRAM The Standard Military Drawing (SMD) program is a program administered by the Defense Electronics Supply Center (DESC) in Dayton, Ohio. Under this program a certified MIL-STD-1772 manufacturer, such as DATEL Inc., may supply a hybrid device using one government controlled Source Control Drawing (SCD). This saves both the customer and supplier time and effort. DATEL Inc. is an active participant in the DESC SMD program. At publication time the following DESC Dreawing numbers have been assigned and are approved or are pending approval. Please contact DATEL Inc. for current status and future SMD compliant products. DESC DRAWING NUMBER DATEL MODEL NUMBER 5962-BB50B 5962-8850B 5962-89528 5962-B952B 5962-B9531 5962-89531 ADC-HX/BB38 ADC-HZlBB38 DAC-HK8/8B38 DAC-HK8-2/8B38 DAC-HP8/B838 DAC-HP8-1/BB38 5962-90857 5962-89996 5962-89996 5962-89996 5962-BB514 5962-8B514 ADC-20B/8838 (pending) DAC-HFB/BB38 (pending) DAC-HF10/8B38 (pending) DAC-HF12/8838 (pending) HDAS-B/BB38 (pending) HDAS-16/BB38 (pending) For Immediate Assistance, Dial 1-800-233-2765 B-1 STILL AVAILABLE The following older DATEL component products have not been included in this new databook. For new designs the component products offered in this databook will provide economically superior performance. For existing designs we at DATEL are committed to supplying our older products to our customers for as long as possible and practical. Please contact our Sales Department for information regarding price, delivery, and minimum order quantity on any of the following. ADC-B500 ADC-B500-1 ADC-B505 ADC-B304 ADC-ECONOVERTER-EXX-HS ADC-EHB1-EXX-HS-BU04 ADC-EH10Bl ADC-EH10B2 ADC-EH12B2 ADC-EH12B3 ADC-EHBBl ADC-EHBB2 ADC-EK10B ADC-EK12B ADC-EK12DC ADC-EK12DM ADC-EK12DR ADC-EKBB ADC-ET10BC ADC-ET10BM ADC-ET12BC ADC-ET12BM ADC-ET12BR ADC-ETBBC ADC-ETBBM ADC-E12B4 ADC-E12D2 ADC-E12D2-EX ADC-E12D3 ADC-HX12BMM-QL ADC-HZ12BMM-QL ADC-MCBBC ADC-MCBBM ADC-149-14B ADC-32AC ADC-32C, ADC-32M ADC-33C ADC-33M ADC-510MC ADC-510MM ADC-5101 ADC-574AT ADC-574ZA ADC-574ZB ADC-574ZC ADC-674ZA ADC-674ZB ADC-674ZC ADC-7109 ADC-BOO ADC-Bl0MC ADC-Bl0MM ADC-BllMC ADC-BllMM ADC-B15MC ADC-B15MM ADC-B15MM-QL ADC-B.16/BB3B ADC-B16MC ADC-B16MM ADC-B17AMC C-l ADC-B17AMM ADC-B17AMM-QL ADC-B25MC ADC-B25MM ADC-B25MM-QL ADC-B26MC ADC-B26MM ADC-B27AMC ADC-B30C ADC-B47A ADC-B47B ADC-B47M ADC-B56C ADC-B56M ADC-BBl ADC-974 ADS-l05MC ADS-l06MC ADS-125MC AM-227 AM-427-1A AM-427-1B AM-427-2B AM-427-2M AM-430A AM-430B AM-450-2 AM-450-2M AM-452-2 AM-452-2M AM-460-2 AM-462-2 AM-464-2 AM-464-2M AM-543MC DAC-DG12Bl DAC-DG12Bl-EXX-HS-BU04 DAC-DG12B2 DAC-DG12B2-EXX-HS DAC-HB12B DAC-HBBB-EXX DAC-HF10BMM-QL DAC-HF12BMM-QL DAC-HFBBMM-QL DAC-Hll0B DAC-Hll0B-EXX-HS-BU04 DAC-HI12B DAC-HI-12B-EXX-HS DAC-HIBB DAC-HIBB-EXX-HS-BU04 DAC-HK-12BMM-QL DAC-HK12BMM-2-QL DAC-HP16BMM-QL DAC-HP16BMM-l-QL DAC-HZ12BMM-QL DAC-IC10B DAC-IC10BC DAC-IC10BM DAC-ll0B DAC-ll0B-EXX-HS DAC-112B DAC-112B-EXX-HS-BU04 DAC-112D DAC-UP10BC DAC-UPBBC DAC-OBBC DAC-OBBM DAC-OB05MR DAC-169-16B DAC-169-16D DAC-29BB DAC-4910B DAC-4912D DAC-562C DAC-562M DAC-60BC DAC-610C DAC-612C DAC-7134BL DAC-7134UL DAC-7523 DAC-7533 DAC-7541 DAC-B30B HDAS-16MM-QL MDAS-16 MDAS-BD MDAS-940D MDAS-940S MS-13 MS-6 MS-7 MVD-409 MX-1606M SCM-l00A SCM-l00B SCM-l0l SDAS-BAl SDAS-BA2 SDAS-BA3 SDAS-BEl SHM-IC-l SHM-IC-1M SHM-LM-2 SHM-UH SHM-UH3 SHM-2 SHM-2-EXX-HS-BU04 SHM-2E SHM-2E-EXX-HS SHM-5 SHM-5-EXX-HS-BU04 VFQ-1C VFQ-1R VFQ-2C VFQ-3C VFV-l0K VFV-l00K VI-7660-1 VI-7660-2 VR-1B2A VR-1B2B VR-1B2C DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 0204B-1194ITEL (50B) 339-3000ITLX 1743BB/FAX (50B) 339-6356 SUBSTITUTION GUIDE FOR DISCONTINUED COMPONENT PRODUCTS The following products are no longer available from DATEL. Where applicable, the nearest equivalent DATEL replacement is listed. Some of these replacement products are functionally similar only and may not be pin-for-pin compatible with the discontinued product. Discontinued Model Nearest Equivelent ADC-300 ADC-301 ADC-302 ADC-303 ADC-310 ADC-508MM ADC-515BMC ADC-515BMM ADC-520MM ADC-521MM ADC-7109 ADC-810MM-QL ADC-816MM-QL ADC-826MM-QL ADC-827AMM ADC-B300E ADC-B301E ADC-B302E ADC-B303 ADC-B310E ADS-105MM ADS-106MM ADS-115MC ADS-115MM ADS-116MC ADS-116MM ADS-125MM ADS-126MC ADS-126MM ADS-21AC ADS-22AC AM-100 Series AM-200 Series AM-427-2A AM-453-2C/2M AM-460-2M AM-7650-1/-2 DAC-330 DAC-7134BJ/BKIUJ/UK DAC-VR Series DAS-952R DILS-1,2,3* HDAS-8MM-QL MS-11* MS-12* MS-2* MS-3* MS-4* MS-5* MS-9* SCM-1 03/1 02 SHM-LM-2M SHM-360 SHM-361 SHM-9 Series TP Series* ADC-208 None None None None ADC-505BMM ADC-500BMC ADC-500BMM ADC-505BMM ADC-505BMM ADC-ET Series ADC-511/883B ADC-511/883B ADC-511/883B ADC-817AMM None None None None None ADS-112MM ADS-112MM ADS-112MC ADS-112MM ADS-112MC ADS-112MM ADS-112MM ADS-112MC AOS-112MM AOS-21PC AOS-21PC AM-551 AM-543MC AM-427-2B AM-450-2 AM-450-2M None OAC-HF10 OAC-71348UUL OAC-HK12 None None HDAS-8/8838 None None None None None None None None SHM-IC-1M None None SHM-IC-1 None *Available through distributors For Immediate Assistance, OiaI1-800-233-2765 0-1 GENERAL DISCLAIMER DATEL Inc. reserves the right to make changes to its products and their specifications at any time, without prior notice to anyone. DATEL Inc. has made every effort to ensure accuracy of the information contained in this databook, but can assume no responsibility for inadvertent errors, omissions, or subsequent changes. DATEL Inc. does not assume any responsibility for the use of any circuitry or other information described within this databook, and further, makes no representations of any kind that the circuitry and information described herein is free of infringement of any intellectual property right or any other right of third parties. No express or implied license of any DATEL Inc. intellectual property right is granted by implication or otherwise. LIFE SUPPORT AND NUCLEAR FACILITY APPLICATIONS POLICY DA TEL Inc. products are not for and should not be used within life support systems or nuclear facility applications without the specific written consent of DA TEL Inc. A Life Support system is a product or system intended to support or sustain life and which if it fails can be reasonably expected to result in significant personal injury or death. Nuclear Facility applications are defined as any application involving a nuclear reactor or any facility involved in any way with the handling or processing of radioactive materials and in which the failure of equipment in any way could reasonably result in harm to life, property or the enviroment. ORDERING GUIDE This ordering guide is presented as a procedural guide. For a formal statement of policies, refer to the TERMS AND CONDITIONS OF SALE found on the Quotation form or on the Customer Acknowledgement copy of the Sales Order. PLACING AN ORDER When ordering a DATEL product, give the complete model number, product description, and option description. Place orders with a DATEL field sales representative or with the factory by leller, telephone, FAX, or TELEX. Minimum order and minimum per shipment is $100. OUTSIDE THE U.S.A. 'AND CANADA Place overseas orders with a DATEL Sales Subsidiary (in West Germany, France, the United Kingdom, and Japan) or with a DATEL overseas sales representative. Orders received directly will be treated the same as if placed through our overseas sales representative. In countries without a DATEL representative, orders should be placed by TELEX and confirmed by air mail. FIELD SALES REPRESENTATIVE DATEL employs field sales representatives throughout the United States, Canada, Europe, and the Far East. DATEL also has Sales Subsidiaries in Munich, West Germany; Paris, France; London, England; and Tokyo and Osaka, Japan. Only these sales representatives are authorized by DATEL to solicit sales, and any information or data received by sources other than these authorized representatives or the DATEL factory are not considered binding. PRICES All prices are F.O.B. , Mansfield, Massachusells, U.S.A. in U.S. dollars. Applicable federal, state, and local taxes are extra and paid by buyer. Prices are subject to change without notice. TERMS Net 30 days DISCOUNTS Quantity discounts are available when placed in a single order. OEM discounts are available on an order or contract basis; consult the factory for details QUOTATIONS Price and delivery quotations made by DATEL or its authorized field sales representatives are valid for 30 days unless otherwise stated. DELIVERY DATEL uses an IBM System 4381, for efficient processing of orders. All orders placed with DATEL are acknowledged .within a few days by an acknowledgement copy of our sales order form. This copy indicates pertinent information including a formal statement of terms and conditions of sale and estimated delivery date. This date has preference over all other agreed upon dates unless otherwise specified. DATEL ships all products in rugged commercial containers suitable for insuring safe delivery under normal shipping conditions. Unless shipping method is specified, the best available method will be used. Shipping charges are normally prepaid and billed to the customer except for Air Freight charges which are sent collect. The appropriate data sheet andior instruction is packed with each product shipped. ORDER CANCELLATION All orders entered with DATEL are binding and are subject to a cancellation charge if cancelled before or after the scheduled shipping date appearing on the acknowledgement copy of the sales order form. Refer to DATEL's Standard Terms and Conditions for specific charges. WARRANTY DATEL warrants that all of its products are free from defects in material and workmanship under normal use and service for a period of one year from date of shipment. DATEL's obligations under this warranty are limited to replacing or repairing, at its option, at its factory or facility, any of the products which shall within the applicable period after shipment be returned to DATEL's facility, transportation charges prepaid, and which are after examination disclosed to the satisfaction of DATEL to be thus defective. This warranty shall not apply to any such equipment which shall have been repaired or altered except by DATEL or which shall have been subjected to misuse, negligence, or accident. In no case shall DATEL's liablilty exceed the original purchase price. The aforementioned provisions do not extend the original warranty period of any product which has either been repaired or replaced by DATEL. RETURNS You will need a return authorization number and shipping instructions from the factory when returning products for any reason. Items should not be returned air freight collect as they connot be accepted. It is absolutely necessary to return products in the manner stated here, otherwise considerable delay will result in processing the return. RETURNS OUTSIDE THE U.S.A. AND CANADA Contact the local sales representative or factory for authorization and shipping instructions first. CERTIFICATE OF COMPLIANCE When requested by the customer DATEL will provide a standard Certificate of Compliance with all shipments. This request must be specified on the purchase order.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No XMP Toolkit : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-21:37:19 Create Date : 2017:07:16 12:42:36-08:00 Modify Date : 2017:07:16 13:17:04-07:00 Metadata Date : 2017:07:16 13:17:04-07:00 Producer : Adobe Acrobat 9.0 Paper Capture Plug-in Format : application/pdf Document ID : uuid:58e905f4-b743-2144-a0be-15064889d0a8 Instance ID : uuid:a8eb665b-b660-fb48-9b53-eb92e9747708 Page Layout : SinglePage Page Mode : UseNone Page Count : 298EXIF Metadata provided by EXIF.tools