Print Preview C 2010_Can Am__DPS ACS_Technical_Manual 2010 Can Am DPS ACS Technical Manual

• toc
  • SAFETY NOTICE
  • INTRODUCTION
    • COLOR CODE LEGEND
  • DYNAMIC POWER STEERING (DPS)
    • General
      • System Description (Features)
        • DPS Assist Mode
          • How to View DPS Assist Mode Selection
          • How to Change DPS Assist Mode
      • System Description (Components)
        • DPS Unit
        • dps unit
          • DPS Unit Protection
        • Steering Torque Sensor
    • Adjustment
      • Torque Offset Reset
      • dps Torque offset reset
      • DPS Assist Mode
    • Troubleshooting
    • No Power Steering Assist
    • Low Power Steering Assist
    • Asymmetrical Power Steering Assist (Side to Side)
    • DPS Will NOT Change Modes of Operation
    • Procedures
      • DPS Unit
        • DPS Unit Power Fuse Test
        • Typical - Outlander 800R LTD illustrated
        • DPS Unit Input Voltage Test (Power Side)
        • DPS Unit Input Voltage Test (Control Side)
        • DPS Unit Ground Circuit Test
        • DPS Unit Communication Link (CAN) Continuity Test
        • DPS System Load Test
        • vDC SELECTED TO MANUAL RANGE 6 0
        • DPS Unit Current Test
        • Typical - LH turn
        • Typical - RH turn
        • DPS Unit Removal
        • Typical
        • Tie rod ends (hardware removed)
        • typical - left side illustrated
        • typical - Right side illustrated
        • DPS Unit Installation
        • Typical - rh side illustrated
        • Steering column indexed to dps shaft splines
        • Typical - rh side illustrated
        • steering column shim measurement
        • typical - lh illustrated
        • DPS Unit Replacement
        • DPS software update
      • Pitman Arm
    • AIR CONTROLLED SUSPENSION (ACS)
    • General
      • System Description (Features)
        • Changing ACS Setting
        • Typical
        • ACS Setting Acknowledgement
        • Typical
        • Using the Auxiliary Line to Inflate Tires
        • Releasing Air Pressure in System for Servicing
      • System Description (Components)
        • Fuse and Relay
          • ACS Fuse (F14)
          • TYPICAL - FRONT SERVICE COMPARTMENT
          • ACS Compressor Relay (R5)
          • Outlander 500 LTD Model
          • Outlander 800R LTD model
        • ACS Main Components
    • Troubleshooting
      • Diagnostic Tips
        • Error Code (AIR FAULT) Displayed in Gauge
          • Error Code Displayed and Suspension Setting Can Not Be Adjusted
      • Troubleshooting Guidelines
        • Requested Setting Display Does Not Change in Gauge
        • Suspension Setting Can Not Be Changed
        • Suspension Setting Can Be Reached to Decrease Pressure Only
        • Suspension Setting Can Be Reached To Increase Pressure Only
        • No Pressure Output from the Auxiliary Line
        • Multifunction Gauge Display Flickers OFF and Back ON
      • Troubleshooting with B.U.D.S.
        • ACS System Leak Test
        • ACS Air Pressure Monitoring
    • Procedures
      • ACS Solenoid Valve
        • ACS Solenoid Valve Operation Test
        • ACS Solenoid Valve Input Voltage Test
        • ACS Solenoid Valve Removal
        • ACS Solenoid Valve Installation
      • ACS Manifold
        • ACS Manifold Removal
        • ACS Manifold Installation
        • Retaining screws are offset toward module fitting
        • Push hose until the mark is completely inserted
        • Hose properly inserted into fitting
      • ACS Module
        • ACS Module Signal Circuit Continuity Test
        • ACS Module Input Voltage Test
        • ACS Module Ground Test
        • ACS Module Removal
        • ACS Module Installation
        • Push hose until the mark is completely inserted
        • Hose properly inserted into fitting
      • ACS Compressor Relay (R5)
        • ACS Relay Continuity Test
        • ACS Relay Input Voltage Test
        • ACS Relay Ground Wire Continuity Test
      • ACS Compressor
        • ACS Compressor Operation Test
        • ACS Compressor Power Wire Continuity Test (from Relay)
        • ACS Compressor Input Voltage Test
        • ACS Compressor Removal
        • ACS Compressor Installation
        • Push hose until the mark is completely inserted
        • Hose properly inserted into fitting
      • ACS Air Filter
        • ACS Air Filter Removal
        • TYPICAL
        • ACS Air Filter Cleaning
          • Prefilter (Foam) Cleaning
          • Filter (Disc) Cleaning
          • Housing Cleaning
      • Pressure Transducer (ACS Auxiliary Line)
        • Pressure Transducer Signal Circuit Continuity Test
        • Pressure Transducer Input Voltage Test
        • Pressure Transducer Ground Test
        • Pressure Transducer Replacement
      • ACS Hoses
        • ACS Hose and Fitting Replacement
        • Auxiliary Line Adapter Replacement
        • Push hose until the mark is completely inserted
        • Hose properly inserted into fitting
      • Shock Absorbers
        • Shock Absorber Removal
        • Shock Absorber Disassembly
        • Shock Absorber Inspection
        • typical
        • Shock Absorber Assembly and Installation
        • Typical