RB HMA Foreword.qxp 2014 Accent
User Manual: 2014-accent
Open the PDF directly: View PDF 
.
Page Count: 406
OWNER'S MANUAL
Operation
Maintenance
Specifications
All information in this Owner's Manual is current at the time of publication.
However, Hyundai reserves the right to make changes at any time so that
our policy of continual product improvement may be carried out.
This manual applies to all models of this vehicle and includes descriptions
and explanations of optional as well as standard equipment. As a result, you
may find material in this manual that does not apply to your specific vehicle.
I
nf
or
mat
i
onPr
ovi
dedby:
CAUTION: MODIFICATIONS TO YOUR HYUNDAI
Your Hyundai should not be modified in any way. Such modifications may adversely affect the performance, safety or durability of your Hyundai and may, in addition, violate conditions of the limited
warranties covering the vehicle. Certain modifications may also be in violation of regulations established by the U.S. Department of Transportation and other federal or state agencies.
TWO-WAY RADIO OR CELLULAR TELEPHONE INSTALLATION
Your vehicle is equipped with electronic fuel injection and other electronic components. It is possible
for an improperly installed/adjusted two-way radio or cellular telephone to adversely affect electronic
systems. For this reason, we recommend that you carefully follow the radio manufacturer's instructions or consult your Hyundai dealer for precautionary measures or special instructions if you choose
to install one of these devices.
F2
I
nf
or
mat
i
onPr
ovi
dedby:
SAFETY AND VEHICLE DAMAGE WARNING
This manual includes information titled as WARNING, CAUTION and NOTICE.
These titles indicate the following:
WARNING
This indicates that a condition may result in harm, serious injury or death to you or other
persons if the warning is not heeded. Follow the advice provided with the warning.
CAUTION
This indicates that a condition may result in damage to your vehicle or its equipment if the
caution is not heeded. Follow the advice provided with the caution.
✽ NOTICE
This indicates that interesting or helpful information is being provided.
I
nf
or
mat
i
onPr
ovi
dedby:
F3
FOREWORD
Thank you for choosing Hyundai. We are pleased to welcome you to the growing number of discerning people who drive Hyundais.
The advanced engineering and high-quality construction of each Hyundai we build is something of which we're very proud.
Your Owner's Manual will introduce you to the features and operation of your new Hyundai. It is suggested that you read it carefully because the information it contains can contribute greatly to the satisfaction you receive from your new car.
The manufacturer also recommends that all service and maintenance on your car be performed by an authorized Hyundai dealer. Hyundai dealers are prepared to provide high-quality service, maintenance and any other assistance that may be required.
HYUNDAI MOTOR AMERICA
Note : Because future owners will also need the information included in this manual, if you sell this Hyundai, please leave the manual in the vehicle for their use. Thank you.
CAUTION
Severe engine and transaxle damage may result from the use of poor quality fuels and lubricants that do not meet Hyundai
specifications. You must always use high quality fuels and lubricants that meet the specifications listed on Page 8-4 in the
Vehicle Specifications and consumer information section of the Owner's Manual.
Copyright 2013 Hyundai Motor America. All rights reserved. No part of this publication may be reproduced, stored in any retrieval
system or transmitted in any form or by any means without the prior written permission of Hyundai Motor America.
F4
I
nf
or
mat
i
onPr
ovi
dedby:
Guide to Hyundai Genuine Parts
1. What are Hyundai Genuine Parts?
Hyundai Genuine Parts are the same
parts used by Hyundai Motor
Company to manufacture vehicles.
They are designed and tested for the
optimum safety, performance, and reliability to our customers.
2. Why should you use genuine parts?
Hyundai Genuine Parts are engineered and built to meet rigid manufacturing requirements. Using imitation, counterfeit or used salvage parts
is not covered under the Hyundai New
Vehicle Limited Warranty or any other
Hyundai warranty.
In addition, any damage to or failure of
Hyundai Genuine Parts caused by the
installation or failure of an imitation,
counterfeit or used salvage part is not
covered by any Hyundai Warranty.
3. How can you tell if you are purchasing Hyundai Genuine Parts?
Look for the Hyundai Genuine Parts
Logo on the package (see below).
Hyundai Genuine Parts exported to
are packaged with labels written only
in English.
Hyundai Genuine Parts are only sold
through authorized Hyundai Dealerships.
A100A01L
A100A02L
I
nf
or
mat
i
onPr
ovi
dedby:
A100A03L
A100A04L
F5
I
nf
or
mat
i
onPr
ovi
dedby:
table of contents
Introduction
1
Your vehicle at a glance
2
Safety features of your vehicle
3
Features of your vehicle
4
Driving your vehicle
5
What to do in an emergency
6
Maintenance
7
Specifications, Consumer information,
Reporting safety defects
8
Index
I
I
nf
or
mat
i
onPr
ovi
dedby:
Introduction
How to use this manual / 1-2
Fuel requirements / 1-3
Vehicle break-in process / 1-5
Vehicle data collection and event data recorders / 1-6
I
nf
or
mat
i
onPr
ovi
dedby:
1
Introduction
HOW TO USE THIS MANUAL
We want to help you get the greatest
possible driving experience from your
vehicle. Your Owner’s Manual can assist
you in many ways. We strongly recommend that you read the entire manual. In
order to minimize the chance of death or
injury, you must read the WARNING and
CAUTION sections in the manual.
Illustrations complement the text in this
manual to best explain how to use your
vehicle. By reading your manual, you will
learn about features, important safety
information, and driving tips under various road conditions.
The general layout of the manual is provided in the Table of Contents. A good
place to start is the index; it has an alphabetical listing of all information in your
manual.
Sections: This manual has eight sections
plus an index. Each section begins with a
brief list of contents so you can tell at a
glance if that section has the information
you want.
You will find various WARNINGS, CAUTIONS, and NOTICES in this manual.
These WARNINGS were prepared to
enhance your personal safety.You should
carefully read and follow ALL procedures
and recommendations provided in these
WARNINGS, CAUTIONS and NOTICES.
WARNING
A WARNING indicates that a condition may result in harm, serious bodily injury or death if the warning is
ignored.
CAUTION
A CAUTION indicates that a condition may result in damage to your
vehicle if the caution is ignored.
✽ NOTICE
A NOTICE indicates interesting or helpful information is being provided.
1 2
I
nf
or
mat
i
onPr
ovi
dedby:
Introduction
FUEL REQUIREMENTS
Your new vehicle is designed to use only
unleaded fuel having a pump octane
number ((R+M)/2) of 87 (Research
Octane Number 91) or higher.
Your new vehicle is designed to obtain
maximum performance with UNLEADED
FUEL, as well as minimize exhaust emissions and spark plug fouling.
CAUTION
Never add any fuel system cleaning
agents to the fuel tank other than
what has been specified. (Consult
an authorized HYUNDAI dealer for
details.)
WARNING
• Do not "top off" after the nozzle
automatically shuts off when
refueling.
• Tighten the cap fully clockwise
until it clicks one time and stops
turning, otherwise the fuel cap
open warning light "
" will illuminate.
• Always check that the fuel cap is
installed securely to prevent fuel
spillage in the event of an accident.
Gasoline containing alcohol and
methanol
Gasohol, a mixture of gasoline and
ethanol (also known as grain alcohol),
and gasoline or gasohol containing
methanol (also known as wood alcohol)
are being marketed along with or instead
of leaded or unleaded gasoline.
Do not use gasohol containing more than
10% ethanol, and do not use gasoline or
gasohol containing any methanol. Either
of these fuels may cause drivability problems and damage to the fuel system.
Discontinue using gasohol of any kind if
drivability problems occur.
Vehicle damage or drivability problems
may not be covered by the manufacturer’s
warranty if they result from the use of:
1. Gasohol containing more than 10%
ethanol.
2. Gasoline or gasohol containing
methanol.
3. Leaded fuel or leaded gasohol.
I
nf
or
mat
i
onPr
ovi
dedby:
"E85" fuel is an alternative fuel comprised of 85 percent ethanol and 15 percent gasoline, and is manufactured
exclusively for use in Flexible Fuel
Vehicles. “E85” is not compatible with
your vehicle. Use of “E85” may result in
poor engine performance and damage to
your vehicle's engine and fuel system.
HYUNDAI recommends that customers
do not use fuel with an ethanol content
exceeding 10 percent.
CAUTION
Your New Vehicle Limited Warranty
does not cover damage to the fuel
system or any performance problems caused by the use of “E85” fuel.
CAUTION
Never use gasohol which contains
methanol. Discontinue use of any
gasohol product which impairs drivability.
1 3
Introduction
Gasoline containing MMT
Some gasoline contains harmful manganese-based fuel additives such as
MMT (Methylcyclopentadienyl Manganese
Tricarbonyl).
HYUNDAI does not recommend the use
of gasoline containing MMT.
This type of fuel can reduce vehicle performance and affect your emission control system.
The malfunction indicator lamp on the
cluster may come on.
Do not use methanol
Fuels containing methanol (wood alcohol) should not be used in your vehicle.
This type of fuel can reduce vehicle performance and damage components of
the fuel system.
CAUTION
Your New Vehicle Limited Warranty
may not cover damage to the fuel
system and any performance problems that are caused by the use of
fuels containing methanol.
1 4
Fuel Additives
HYUNDAI recommends that you use good
quality gasolines treated with detergent
additives such as TOP TIER Detergent
Gasoline, which help prevent deposit formation in the engine. These gasolines will
help the engine run cleaner and enhance
performance of the Emission Control
System. For more information on TOP
TIER Detergent Gasoline, please go to the
website (www.toptiergas.com).
For customers who do not use TOP Tier
Detergent Gasoline regularly, and have
problems starting or the engine does not
run smoothly, additives that you can buy
separately may be added to the gasoline.
If TOP TIER Detergent Gasoline is not
available, one bottle of additive added to
the fuel tank at every 7,500mile or every
engine oil change is recommended.
Additives are available from your authorized HYUNDAI dealer along with information on how to use them. Do not mix other
additives.
I
nf
or
mat
i
onPr
ovi
dedby:
Operation in foreign countries
If you are going to drive your vehicle in
another country, be sure to:
• Observe all regulations regarding registration and insurance.
• Determine that acceptable fuel is available.
Introduction
VEHICLE BREAK-IN PROCESS
No special break-in period is needed. By
following a few simple precautions for the
first 600 miles (1,000 km) you may add to
the performance, economy and life of
your vehicle.
• Do not race the engine.
• While driving, keep your engine speed
(rpm, or revolutions per minute)
between 2,000 rpm and 4,000 rpm.
• Do not maintain a single speed for long
periods of time, either fast or slow.
Varying engine speed is needed to
properly break-in the engine.
• Avoid hard stops, except in emergencies, to allow the brakes to seat properly.
• Do not let the engine idle longer than 3
minutes at one time.
CALIFORNIA PROPOSITION 65 WARNING
Items contained in motor vehicles
or emitted from them are known to
the State of California to cause cancer and birth defects or reproductive harm. These include:
• Gasoline and its vapors
• Engine exhaust
• Used engine oil
• Interior passenger compartment
components and materials
• Component parts which are subject to heat and wear
In addition, battery posts, terminals
and related accessories contain
lead, lead compounds and other
chemicals known to the State of
California to cause cancer and
reproductive harm.
I
nf
or
mat
i
onPr
ovi
dedby:
1 5
Introduction
VEHICLE DATA COLLECTION AND EVENT DATA RECORDERS
This vehicle is equipped with an event
data recorder (EDR). The main purpose of an EDR is to record, in certain
crash or near crash-like situations,
such as an air bag deployment or hitting a road obstacle, data that will
assist in understanding how a vehicle's systems performed. The EDR is
designed to record data related to
vehicle dynamics and safety systems
for a short period of time, typically 30
seconds or less. The EDR in this vehicle is designed to record such data as:
• How various systems in your vehicle
were operating;
• Whether or not the driver and passenger safety belts were buckled/
fastened;
• How far (if at all) the driver was
depressing the accelerator and/or
brake pedal; and,
• How fast the vehicle was traveling.
1 6
These data can help provide a better
understanding of the circumstances
in which crashes and injuries occur.
NOTE: EDR data are recorded by your
vehicle only if a non-trivial crash situation occurs; no data are recorded by
the EDR under normal driving conditions and no personal data (e.g.,
name, gender, age, and crash location) are recorded. However, other
parties, such as law enforcement,
could combine the EDR data with the
type of personally identifying data
routinely acquired during a crash
investigation.
I
nf
or
mat
i
onPr
ovi
dedby:
To read data recorded by an EDR, special equipment is required, and
access to the vehicle or the EDR is
needed. In addition to the vehicle
manufacturer, other parties, such as
law enforcement, that have the special
equipment, can read the information if
they have access to the vehicle or the
EDR.
Your vehicle at a glance
Interior overview / 2-2
Instrument panel overview / 2-3
Engine compartment / 2-4
I
nf
or
mat
i
onPr
ovi
dedby:
2
Your vehicle at a glance
INTERIOR OVERVIEW
1. Door lock/unlock button ..........................4-8
2. Outside rearview mirror control
switch* ..................................................4-34
3. Central door lock switch* ........................4-9
4. Power window lock button*....................4-19
5. Power window switches* ......................4-16
6. Instrument panel illumination control
switch* ..................................................4-37
7. ESC OFF button* ..................................5-21
8. Active ECO button ................................5-31
9. Fuel filler lid release lever ....................4-23
10. Trunk lid release lever (4 Door) ..........4-12
11. Fuse box..............................................7-51
12. Hood release lever ..............................4-21
13. Brake pedal ........................................5-16
14. Accelerator pedal ................................5-6
15. Steering wheel tilt and telescopic
lever* ..................................................4-31
* : if equipped
❈ The actual vehicle may differ from the illustration.
ORB014001N
2 2
I
nf
or
mat
i
onPr
ovi
dedby:
Your vehicle at a glance
INSTRUMENT PANEL OVERVIEW
1. Driver’s front air bag.........................3-46
2. Horn .................................................4-32
3. Light control/Turn signals .................4-53
4. Instrument cluster.............................4-36
5. Wiper/Washer...................................4-57
6. Ignition switch.....................................5-5
7. Digital clock and audio* .............4-89, 4-94
8. Steering wheel .................................4-30
9. Steering wheel audio control* ..........4-95
10. Climate control system* ........4-65, 4-74
11. Hazard warning flasher switch..4-52, 6-2
12. Shift lever ................................5-7, 5-10
13. Parking brake lever ........................5-17
14. Passenger’s front air bag ...............3-46
15. Glove box .......................................4-85
16. Power outlet* ..................................4-88
* : if equipped
ORB010002N
I
nf
or
mat
i
onPr
ovi
dedby:
2 3
Your vehicle at a glance
ENGINE COMPARTMENT
1. Engine coolant reservoir ...................7-23
2. Windshield washer fluid reservoir .....7-27
3. Radiator cap .....................................7-25
4. Engine oil filler cap ...........................7-22
5. Engine oil dipstick .............................7-22
6. Brake/clutch fluid reservoir ...............7-26
7. Air cleaner.........................................7-29
8. Fuse box ...........................................7-51
9. Positive battery terminal ...................7-34
10. Negative battery terminal................7-34
* : if equipped
* The actual engine room in the vehicle may differ from the illustration.
ORB070100
2 4
I
nf
or
mat
i
onPr
ovi
dedby:
Seats / 3-2
Seat belts / 3-14
Child restraint system / 3-26
Air bag - advanced supplemental restraint system / 3-34
Safety features of your vehicle
I
nf
or
mat
i
onPr
ovi
dedby:
3
Safety features of your vehicle
SEATS
Driver’s seat
(1) Forward and backward
(2) Seatback angle
(3) Seat cushion height
(4) Headrest
(5) Armrest*
Front passenger’s seat
(6) Forward and backward
(7) Seatback angle
(8) Headrest
Rear seat
(9) Headrest*
(10) Seatback folding*
*: if equipped
ORB030001N
3 2
I
nf
or
mat
i
onPr
ovi
dedby:
Safety features of your vehicle
WARNING - Loose objects
Loose objects in the driver’s foot
area could interfere with the operation of the foot pedals, possibly
causing an accident. Do not place
anything under the front seats.
WARNING - Uprighting
seat
When you return the seatback to its
upright position, hold the seatback
and return it slowly and be sure
there are no other occupants
around the seat. If the seatback is
returned without being held and
controlled, the back of the seat
could spring forward resulting in
accidental injury to a person struck
by the seatback.
WARNING - Driver responsibility for passengers
Riding in a vehicle with the seatback reclined could lead to serious
or fatal injury in an accident. If a
seat is reclined during an accident,
the occupant’s hips may slide
under the lap portion of the seat
belt, applying great force to the
unprotected abdomen. Serious or
fatal internal injuries could result.
The driver must advise the passenger to keep the seatback in an
upright position whenever the vehicle is in motion.
WARNING
Do not use a sitting cushion that
reduces friction between the seat
and passenger. The passenger's
hips may slide under the lap portion of the seat belt during an accident or a sudden stop. Serious or
fatal internal injuries could result
because the seat belt can't operate
normally.
I
nf
or
mat
i
onPr
ovi
dedby:
WARNING - Driver’s seat
• Never attempt to adjust the seat
while the vehicle is moving. This
could result in loss of control,
and an accident causing death,
serious injury, or property damage.
• Do not allow anything to interfere
with the normal position of the
seatback. Storing items against a
seatback or in any other way
interfering with proper locking of
a seatback could result in serious
or fatal injury in a sudden stop or
collision.
• Always drive and ride with your
seatback upright and the lap portion of the seat belt snug and low
across the hips. This is the best
position to protect you in case of
an accident.
• In order to avoid unnecessary
and perhaps severe air bag
injuries, always sit as far back as
possible from the steering wheel
while maintaining comfortable
control of the vehicle. We recommend that your chest be at least
10 inches (250 mm) away from
the steering wheel.
3 3
Safety features of your vehicle
WARNING - Rear
seatbacks
• The rear seatback must be
securely latched. If not, passengers and objects could be thrown
forward resulting in serious
injury or death in the event of a
sudden stop or collision.
• No passenger should ride in the
cargo area or sit or lie on folded
seatbacks while the vehicle is
moving. All passengers must be
properly seated in seats and
restrained properly while riding.
• When resetting the seatback to
the upright position, make sure it
is securely latched by pushing it
forward and rearwards.
• To avoid the possibility of burns,
do not remove the carpet in the
cargo area. Emission control
devices beneath this floor generate high temperatures.
(Continued)
3 4
(Continued)
• Luggage and other cargo should
be laid flat in the cargo area. If
objects are large, heavy, or must
be piled, they must be secured.
Under no circumstances should
cargo be piled higher than the
seatbacks. Failure to follow these
warnings could result in serious
injury or death in the event of a
sudden stop, collision or rollover.
WARNING
After adjusting the seat, always
check that it is securely locked into
place by attempting to move the
seat forward or reverse without
using the lock release lever.
Sudden or unexpected movement
of the driver's seat could cause you
to lose control of the vehicle resulting in an accident.
I
nf
or
mat
i
onPr
ovi
dedby:
WARNING
• Do not adjust the seat while wearing seat belts. Moving the seat
cushion forward may cause
strong pressure on the abdomen.
• Use extreme caution so that
hands or other objects are not
caught in the seat mechanisms
while the seat is moving.
• Do not put a cigarette lighter on
the floor or seat. When you operate the seat, gas may gush out of
the lighter and cause fire.
Safety features of your vehicle
ORB030003
ORB030004
Seatback angle
To recline the seatback:
1. Lean forward slightly and lift up the
seatback recline lever.
2. Carefully lean back on the seat and
adjust the seatback of the seat to the
position you desire.
3. Release the lever and make sure the
seatback is locked in place. (The lever
MUST return to its original position for
the seatback to lock.)
Seat cushion height (for driver’s seat)
(if equipped)
To change the height of the seat cushion,
push the lever upwards or downwards.
• To lower the seat cushion, push the
lever down several times.
• To raise the seat cushion, pull the lever
up several times.
ORB030002
Front seat
Manual adjustment
Forward and rearward
To move the seat forward or rearward:
1. Pull the seat slide adjustment lever up
and hold it.
2. Slide the seat to the position you
desire.
3. Release the lever and make sure the
seat is locked in place.
Adjust the seat before driving, and make
sure the seat is locked securely by trying
to move forward and rearward without
using the lever. If the seat moves, it is not
locked properly.
I
nf
or
mat
i
onPr
ovi
dedby:
3 5
Safety features of your vehicle
WARNING
ORB030006
OMG038400
Armrest (for driver’s seat)
(if equipped)
To use the armrest, swing down the armrest to the lowest position.
Headrest
The driver's and front passenger's seats
are equipped with a headrest for the
occupant's safety and comfort.
The headrest not only provides comfort
for the driver and front passenger, but
also helps to protect the head and neck
in the event of a collision.
3 6
I
nf
or
mat
i
onPr
ovi
dedby:
• For maximum effectiveness in
case of an accident, the headrest
should be adjusted so the middle
of the headrest is at the same
height of the center of gravity of
an occupant's head. Generally,
the center of gravity of most people's head is similar with the
height of the top of their eyes.
Also, adjust the headrest as close
to your head as possible. For this
reason, the use of a cushion that
holds the body away from the
seatback is not recommended.
• Do not operate the vehicle with
the headrests removed as severe
injury to the occupants may
occur in the event of an accident.
Headrests may provide protection against neck injuries when
properly adjusted.
• Do not adjust the headrest position of the driver's seat while the
vehicle is in motion.
Safety features of your vehicle
ORB030007
ORB030032
ORB030033
Adjusting the height up and down
To raise the headrest, pull it up to the
desired position (1). To lower the headrest, push and hold the release button (2)
on the headrest support and lower the
headrest to the desired position (3).
Removal
To remove the headrest:
1. Recline the seatback (2) with the
recline lever (1).
2. Raise headrest as far as it can go.
3. Press the headrest release button (3)
while pulling the headrest up (4).
Reinstall
To reinstall the headrest:
1. Put the headrest poles (2) into the
holes while pressing the release button (1).
2. Recline the seatback (4) with the
recline lever (3).
3. Adjust the headrest to the appropriate
height.
WARNING
NEVER allow anyone to ride in a
seat with the headrest removed.
WARNING
Always make sure the headrest
locks into position after reinstalling
and adjusting it properly.
I
nf
or
mat
i
onPr
ovi
dedby:
3 7
Safety features of your vehicle
WARNING
A gap between the seat and the
headrest release button may
appear when seating on the seat or
when you push or pull the seat. Be
careful not to get your finger, etc.
caught in the gap.
HNF2041-1
ORB030017
Active headrest (if equipped)
The active headrest is designed to move
forward and upward during a rear impact.
This helps to prevent the driver's and
front passenger’s head from moving
rearward and thus helps prevent neck
injuries.
Seatback pocket (if equipped)
The seatback pocket is provided on the
back of the front passenger’s and driver’s
seatbacks.
WARNING - Seatback
pockets
Do not put heavy or sharp objects
in the seatback pockets. In an accident they could come loose from
the pocket and injure vehicle occupants.
3 8
I
nf
or
mat
i
onPr
ovi
dedby:
Safety features of your vehicle
WARNING
WARNING
For proper operation of the occupant detection system:
• Do not place any items cumulatively weighing over 2.2 lbs (1 kg)
in the seatback pocket or on the
seat.
• Do not hang onto the front passenger seat.
ONF039401
Rear seat
Headrest
The rear seat(s) is equipped with headrests in all the seating positions for the
occupant's safety and comfort.
The headrest not only provides comfort
for passengers, but also helps to protect
the head and neck in the event of a collision.
I
nf
or
mat
i
onPr
ovi
dedby:
• For maximum effectiveness in
case of an accident, the headrest
should be adjusted so the middle
of the headrest is at the same
height of the center of gravity of
an occupant's head. Generally,
the center of gravity of most people's head is similar with the
height of the top of their eyes.
Also adjust the headrest as close
to your head as possible. For this
reason, the use of a cushion that
holds the body away from the
seatback is not recommended.
• Do not operate the vehicle with
the headrests removed as severe
injury to an occupant may occur
in the event of an accident.
Headrests may provide protection against severe neck injuries
when properly adjusted.
3 9
Safety features of your vehicle
Reinstall
To reinstall the headrest, put the headrest poles (3) into the holes while pressing the release button (1). Then adjust it
to the appropriate height.
WARNING
Make sure the headrest locks in
position after adjusting it to properly protect the occupants.
ORB030007
ORB030008
Adjusting the height up and down
To raise the headrest, pull it up (1). To
lower the headrest, push and hold the
release button (2) on the headrest support and lower the headrest (3).
Removal
To remove the headrest, raise it as far as
it can go then press the release button
(1) while pulling upward (2).
3 10
I
nf
or
mat
i
onPr
ovi
dedby:
Safety features of your vehicle
Folding the rear seat
The rear seatbacks can be folded to facilitate carrying long items or to increase
the luggage capacity of the vehicle.
■ Type A
WARNING
The purpose of the fold-down rear
seatbacks is to allow you to carry
longer objects that could not be
accommodated in the cargo area.
Never allow passengers to sit on
top of the folded down seatback
while the vehicle is moving. This is
not a proper seating position and
no seat belts are available for use.
This could result in serious injury
or death in case of an accident or
sudden stop. Objects carried on the
folded down seatback should not
extend higher than the top of the
front seatbacks. Doing this could
allow cargo to slide forward and
cause injury or damage during sudden stops.
ORB030022
ORB030021
To fold down the rear seatback:
1. Make sure the rear seat belt webbing
is in the guide to prevent the seat belt
from being damaged.
2. Set the front seatback to the upright
position and if necessary, slide the
front seat forward.
3. Lower the rear headrests to the lowest
position.
■ Type B
ORBC032022
4. Pull on the seatback folding lever, then
fold the seat toward the front of the
vehicle.
I
nf
or
mat
i
onPr
ovi
dedby:
3 11
Safety features of your vehicle
✽ NOTICE
If you are not able to pull out the seat
belt from the retractor, after returning
the seatback to the upright position,
press the seatbelt and seatback at the
same time. Then pull the belt out. You
will be able to pull the belt out smoothly.
CAUTION - Damaging rear
seat belt buckles
When folding the rear seatback,
insert the buckle in the pocket
between the rear seatback and
cushion. Doing so can prevent the
buckle from being damaged by the
rear seatback.
WARNING
ORBR030031
5. To use the rear seat, lift and pull the
seatback backward. Push the seatback firmly until it clicks into place.
Make sure the seatback is locked in
place. When you return the seatback
to its upright position, always be sure it
has locked into position by pushing on
the top of the seatback.
6. Return the rear seat belt to the proper
position.
3 12
When you return the rear seatback
to its upright position after being
folded down:
Be careful not to damage the seat
belt webbing or buckle. Do not
allow the seat belt webbing or
buckle to get caught or pinched in
the rear seat. Ensure that the seatback is completely locked into its
upright position by pushing on the
top of the seatback. Otherwise, in
an accident or sudden stop, the
seat could fold down and allow
cargo to enter the passenger compartment, which could result in
serious injury or death.
I
nf
or
mat
i
onPr
ovi
dedby:
CAUTION - Rear seat belts
When returning the rear seatbacks
to the upright position, remember
to return the rear shoulder belts to
their proper position. Routing the
seat belt webbing through the rear
seat belt guides will help keep the
seat belts from being trapped
behind or under the seats.
Safety features of your vehicle
WARNING - Cargo
Cargo should always be secured to
prevent it from being thrown about
the vehicle in a collision and causing injury to the vehicle occupants.
Do not place objects in the rear
seats, since they cannot be properly secured and may hit the front
seat occupants in a collision.
WARNING - Cargo loading
Make sure the engine is off, the
automatic transaxle is in P (Park)
or the manual transaxle is in R
(Reverse) or 1st, and the parking
brake is securely applied whenever
loading or unloading cargo. Failure
to take these steps may allow the
vehicle to move if the shift lever is
inadvertently moved to another
position.
I
nf
or
mat
i
onPr
ovi
dedby:
3 13
Safety features of your vehicle
SEAT BELTS
Seat belt restraint system
WARNING
• For maximum restraint system
protection, the seat belts must
always be used whenever the car
is moving.
• Seat belts are most effective
when seatbacks are in the
upright position.
• Children age 12 and younger
must
always
be
properly
restrained in the rear seat. Never
allow children to ride in the front
passenger seat. If a child over 12
must be seated in the front seat,
he/she must be properly belted
and the seat should be moved as
far back as possible.
• Never wear the shoulder belt
under your arm or behind your
back. An improperly positioned
shoulder belt can cause serious
injuries in a crash. The shoulder
belt should be positioned midway
over your shoulder across your
collarbone.
(Continued)
3 14
(Continued)
• Avoid wearing twisted seat belts.
A twisted belt can't do its job as
well. In a collision, it could even
cut into you. Be sure the belt
webbing is straight and not twisted.
• Be careful not to damage the belt
webbing or hardware. If the belt
webbing or hardware is damaged, replace it.
WARNING
Seat belts are designed to bear
upon the bony structure of the
body, and should be worn low
across the front of the pelvis, chest
and shoulders, as applicable; wearing the lap section of the belt
across the abdominal area must be
avoided.
Seat belts should be adjusted as
firmly as possible, consistent with
comfort, to provide the protection
for which they have been designed.
A slack belt will greatly reduce the
protection afforded to the occupant.
(Continued)
I
nf
or
mat
i
onPr
ovi
dedby:
(Continued)
Care should be taken to avoid contamination of the webbing with polishes, oils and chemicals and particularly battery acid. Cleaning may
safely be carried out using mild
soap and water. The belt should be
replaced if webbing becomes
frayed, contaminated or damaged.
It is essential to replace the entire
assembly after it has been worn in
a severe impact even if damage to
the assembly is not obvious. Belts
should not be worn with straps
twisted. Each seat belt assembly
must only be used by one occupant; it is dangerous to put a belt
around a child being carried on the
occupant's lap.
Safety features of your vehicle
Conditions
WARNING
• No modifications or additions
should be made by the user
which will either prevent the seat
belt adjusting devices from operating to remove slack, or prevent
the seat belt assembly from being
adjusted to remove slack.
• When you fasten the seat belt, be
careful not to latch the seat belt in
buckles of other seat. It's very dangerous and you may not be protected by the seat belt properly.
• Do not unfasten the seat belt and
do not fasten and unfasten the
seat belt repeatedly while driving.
This could result in loss of control, and an accident causing
death, serious injury, or property
damage.
• When fastening the seat belt,
make sure that the seat belt does
not pass over objects that are
hard or can break easily.
• Make sure there is nothing in the
buckle. The seat belt may not be
fastened securely.
Seat Belt
Vehicle
Speed
Unbuckled
1GQA2083
Seat belt warning (for driver’s seat)
The driver's seat belt warning light and
chime will activate to the following table
when the ignition switch is in "ON" position.
Unbuckled
ChimeSound
Light-Blink
6 seconds
Buckled
Buckled →
Unbuckled
Warning Pattern
6 seconds
None
Below 3 mph
6 seconds
(5 km/h)
None
3 mph~
6 mph
6 seconds
Above 6 mph
(10 km/h)
6 sec. on / 24 sec. off
(11 times)
Above 6 mph
(10 km/h)
6 seconds *1
↓
↓
Below 3 mph
(5 km/h)
Stop *2
*1 Warning pattern repeats 11 times with
an interval of 24 seconds. If the driver's
seat belt is buckled, the light will stop
within 6 seconds and chime will stop
immediately.
*2 The light will stop within 6 seconds and
chime will stop immediately.
I
nf
or
mat
i
onPr
ovi
dedby:
3 15
Safety features of your vehicle
✽ NOTICE
Front seat
If you are not able to pull out the seat
belt from the retractor, firmly pull the
belt out and release it. Then you will be
able to pull the belt out smoothly.
B180A01NF-1
ORB030020
Seat belt - Driver's 3-point system
with emergency locking retractor
To fasten your seat belt:
To fasten your seat belt, pull it out of the
retractor and insert the metal tab (1) into
the buckle (2). There will be an audible
"click" when the tab locks into the buckle.
The seat belt automatically adjusts to the
proper length only after the lap belt portion is adjusted manually so that it fits
snugly around your hips. If you lean forward in a slow, easy motion, the belt will
extend and let you move around. If there
is a sudden stop or impact, however, the
belt will lock into position. It will also lock
if you try to lean forward too quickly.
Height adjustment (Front)
You can adjust the height of the shoulder
belt anchor to one of 4 positions for maximum comfort and safety.
The height of the adjusting seat belt should
not be too close to your neck. The shoulder
portion should be adjusted so that it lies
across your chest and midway over your
shoulder nearest to the door and not next
to your neck.
To adjust the height of the seat belt anchor,
lower or raise the height adjuster into an
appropriate position.
To raise the height adjuster, pull it up (1).To
lower it, push it down (3) while pressing the
height adjuster button (2).
Release the button to lock the anchor into
position. Try sliding the height adjuster to
make sure that it has locked into position.
3 16
I
nf
or
mat
i
onPr
ovi
dedby:
Safety features of your vehicle
WARNING
• Verify the shoulder belt anchor is
locked into position at the appropriate height. Never position the
shoulder belt across your neck or
face. Improperly positioned seat
belts can cause serious injuries
in an accident.
• Failure to replace seat belts after
an accident could leave you with
damaged seat belts that will not
provide protection in the event of
another collision leading to personal injury or death. Replace
your seat belts after being in an
accident as soon as possible.
B200A02NF
WARNING
You should place the lap belt portion as low as possible and snugly
across your hips, not on your waist.
If the lap belt is located too high on
your waist, it may increase the
chance of injury in the event of a
collision. Both arms should not be
under or over the belt. Rather, one
should be over and the other under,
as shown in the illustration.
Never wear the seat belt under the
arm nearest the door.
I
nf
or
mat
i
onPr
ovi
dedby:
Seat belts - Front passenger and rear
seat 3-point system with combination
locking retractor
To fasten your seat belt:
Combination retractor type seat belts are
installed in the rear seat positions to help
accommodate the installation of child
restraint systems. Although a combination retractor is also installed in the front
passenger seat position, it is strongly
recommended that children always be
seated in the rear seat. NEVER place
any infant restraint system in the front
seat of the vehicle.
This type of seat belt combines the features of both an emergency locking
retractor seat belt and an automatic locking retractor seat belt. To fasten your seat
belt, pull it out of the retractor and insert
the metal tab into the buckle. There will
be an audible "click" when the tab locks
into the buckle. When not securing a
child restraint, the seat belt operates in
the same way as the driver's seat belt
(Emergency Locking Retractor Type). It
automatically adjusts to the proper length
only after the lap belt portion of the seat
belt is adjusted manually so that it fits
snugly around your hips.
3 17
Safety features of your vehicle
When the seat belt is fully extended from
the retractor to allow the installation of a
child restraint system, the seat belt operation changes to allow the belt to retract,
but not to extend (Automatic Locking
Retractor Type). Refer to “Using a child
restraint system” in this section.
A
B
✽ NOTICE
Although the combination retractor
provides the same level of protection for
seated passengers in either emergency
or automatic locking modes, it is recommended that seated passengers use the
emergency locking feature for improved
convenience. The automatic locking
function is intended to facilitate child
restraint installation. To convert from
the automatic locking feature to the
emergency locking operation mode,
allow the unbuckled seat belt to fully
retract.
ORB031035N
B210A01NF-1/H
To release the seat belt:
The seat belt is released by pressing the
release button (1) in the locking buckle.
When it is released, the belt should automatically draw back into the retractor.
If this does not happen, check the belt to
be sure it is not twisted, then try again.
ORB031036N
3 Point rear center belt
To fasten the rear center belt
Insert the tongue plate (A) into the open
end of the buckle (B) until an audible
“click" is heard, indicating the latch is
locked. Make sure the belt is not twisted.
3 18
I
nf
or
mat
i
onPr
ovi
dedby:
Safety features of your vehicle
CAUTION
When using the rear center seat
belt, the buckle with the “CENTER”
mark must be used.
C
1
WARNING
When using the rear seat center
belt, you must lock all tongue
plates and buckles. If any tongue
plate or buckle is not locked, it will
increase the chance of injury in the
event of a collision.
D
D
ORB031032N
ORB031037N
Pull and insert the tongue plate (C) into
the open end of the buckle (D) until an
audible “click” is heard, indicating the
latch is locked.
Make sure the belt is not twisted.
There will be an audible “click” when the
tab locks in the buckle. The seat belt
automatically adjusts to the proper length
only after the lap belt is adjusted manually so that it fits snugly around your hips,
if you lean forward in a slow, easy
motion, the belt will extend and let you
move around. If there is a sudden stop or
impact, the belt will lock into position. It
will also lock if you try to lean forward too
quickly.
To unfasten the rear center belt
Press the release button (1) on the buckle (D) and remove the tongue plate from
the buckle (D).
I
nf
or
mat
i
onPr
ovi
dedby:
3 19
Safety features of your vehicle
If the system senses excessive tension
on the driver or passenger's seat belt
when the pre-tensioner activates, the
load limiter inside the pre-tensioner will
release some of the pressure on the
affected seat belt.
✽ NOTICE
ORB031038N
To disconnect the rear center belt
Insert a key or narrow-ended tool into the
groove located on buckle.
✽ NOTICE
Always connect the tongue plate to the
buckle even when not in use.
3 20
OED030300
The pre-tensioner will activate not only
in a frontal collision but also in a side
collision, if the vehicle is equipped with
a side or curtain air bag.
Pre-tensioner seat belt
Your vehicle is equipped with driver's and
front passenger's pre-tensioner seat
belts. The purpose of the pre-tensioner is
to make sure that the seat belts fit tightly
against the occupant's body in certain
frontal collisions (or side collisions). The
pre-tensioner seat belts may be activated
in crashes where the frontal collision (or
side collisions) is severe enough.
When the vehicle stops suddenly, or if
the occupant tries to lean forward too
quickly, the seat belt retractor will lock
into position. In certain frontal collisions
(or side collisions), the pre-tensioner will
activate and pull the seat belt into tighter
contact against the occupant's body.
I
nf
or
mat
i
onPr
ovi
dedby:
WARNING
• Do not put anything near the
buckle. Placing objects near the
buckle can adversely affect the
buckle pre-tensioner and may
increase the risk of personal
injury in the event of a collision.
• For your safety, be sure that the
belt webbing is not loose or twisted and always sit properly on
your seat.
Safety features of your vehicle
WARNING
OMD030051N
The seat belt pre-tensioner system consists mainly of the following components.
Their locations are shown in the illustration:
1. SRS air bag warning light
2. Retractor pre-tensioner assembly
3. SRS control module
4. Anchor pre-tensioner assembly
To obtain maximum benefit from a
pre-tensioner seat belt:
1. The seat belt must be worn correctly and adjusted to the proper
position. Please read and follow
all of the important information
and precautions about your vehicle’s occupant safety features –
including seat belts and air bags
– that are provided in this manual.
2. Be sure you and your passengers always wear seat belts properly.
I
nf
or
mat
i
onPr
ovi
dedby:
✽ NOTICE
• Both the driver's and front passenger's pre-tensioner seat belts may be
activated in certain frontal collisions
(or side collisions).
The pre-tensioners will not be activated if the seat belts are not being worn
at the time of the collision.
• When the pre-tensioner seat belts are
activated, a loud noise may be heard
and fine dust, which may appear to be
smoke, may be visible in the passenger
compartment. These are normal operating conditions and are not hazardous.
• Although it is harmless, the fine dust
may cause skin irritation and should
not be breathed for prolonged periods. Wash all exposed skin areas thoroughly after an accident in which the
pre-tensioner seat belts were activated.
• Because the sensor that activates the
SRS air bag is connected with the pretensioner seat belt, the SRS air bag
warning light
on the instrument
panel will illuminate for approximately 6 seconds after the ignition switch
has been turned to the ON position,
and then it should turn off.
3 21
Safety features of your vehicle
CAUTION
If the pre-tensioner seat belt is not
working properly, this warning light
will illuminate even if there is no
malfunction of the SRS air bag. If
the SRS air bag warning light does
not illuminate when the ignition
switch is turned ON, or if it remains
illuminated after illuminating for
approximately 6 seconds, or if it
illuminates while the vehicle is
being driven, have an authorized
HYUNDAI dealer inspect the pretensioner seat belt and SRS air bag
system as soon as possible.
WARNING
• Pre-tensioners are designed to
operate only one time. After activation, pre-tensioner seat belts
must be replaced. All seat belts,
of any type, should always be
replaced after they have been
worn during a collision.
(Continued)
3 22
(Continued)
• The pre-tensioner seat belt
assembly mechanisms become
hot during activation. Do not
touch the pre-tensioner seat belt
assemblies for several minutes
after they have been activated.
• Do not attempt to inspect or
replace the pre-tensioner seat
belts yourself. This must be done
by an authorized HYUNDAI dealer.
• Do not strike the pre-tensioner
seat belt assemblies.
• Do not attempt to service or
repair the pre-tensioner seat belt
system in any manner.
• Improper handling of the pre-tensioner seat belt assemblies, and
failure to heed the warnings not
to strike, modify, inspect, replace,
service or repair the pre-tensioner seat belt assemblies may lead
to improper operation or inadvertent activation and serious injury.
• Always wear the seat belts when
driving or riding in a motor vehicle.
• If the vehicle or pre-tensioner seat
belt must be discarded, contact
an authorized HYUNDAI dealer.
I
nf
or
mat
i
onPr
ovi
dedby:
Seat belt precautions
WARNING
All occupants of the vehicle must
wear their seat belts at all times.
Seat belts and child restraints
reduce the risk of serious or fatal
injuries for all occupants in the
event of a collision or sudden stop.
Without a seat belt, occupants
could be shifted too close to a
deploying air bag, strike the interior
structure or be thrown from the
vehicle. Properly worn seat belts
greatly reduce these hazards.
Even with advanced air bags,
unbelted occupants can be severely injured by a deploying air bag.
Always follow the precautions
about seat belts, air bags and occupant seating contained in this manual.
Safety features of your vehicle
Infant or small child
All 50 states have child restraint laws.You
should be aware of the specific requirements in your state. Child and/or infant
seats must be properly placed and
installed in the rear seat. For more information about the use of these restraints,
refer to “Child restraint system” in this
section.
WARNING
Every person in your vehicle needs
to be properly restrained at all
times, including infants and children. Never hold a child in your
arms or lap when riding in a vehicle. The violent forces created during a crash will tear the child from
your arms and throw the child
against the interior. Always use a
child restraint appropriate for your
child's height and weight.
✽ NOTICE
Small children are best protected from
injury in an accident when properly
restrained in the rear seat by a child
restraint system that meets the requirements of the Federal Motor Vehicle
Safety Standards. Before buying any
child restraint system, make sure that it
has a label certifying that it meets
Federal Motor Vehicle Safety Standard
213. The restraint must be appropriate
for your child's height and weight.
Check the label on the child restraint for
this information. Refer to “Child
restraint system” in this section.
I
nf
or
mat
i
onPr
ovi
dedby:
Larger children
Children who are too large for child
restraint systems should always occupy
the rear seat and use the available
lap/shoulder belts. The lap portion should
be fastened snug on the hips and as low
as possible. Check belt fit periodically. A
child's squirming could put the belt out of
position. Children are afforded the most
safety in the event of an accident when
they are restrained by a proper restraint
system in the rear seat. If a larger child
(over age 12) must be seated in the front
seat, the child should be securely
restrained by the available lap/shoulder
belt and the seat should be placed in the
rearmost position. Children age 12 and
under should be restrained securely in
the rear seat. NEVER place a child age
12 and under in the front seat. NEVER
place a rear facing child seat in the front
seat of a vehicle.
3 23
Safety features of your vehicle
If the shoulder belt portion slightly touches the child’s neck or face, try placing the
child closer to the center of the vehicle. If
the shoulder belt still touches their face
or neck they need to be returned to a
child restraint system.
WARNING - Shoulder belts
on small children
• Never allow a shoulder belt to be
in contact with a child’s neck or
face while the vehicle is in
motion.
• If seat belts are not properly worn
and adjusted on children, there is
a risk of death or serious injury.
3 24
Pregnant women
The use of a seat belt is recommended
for pregnant women to lessen the chance
of injury in an accident. When a seat belt
is used, the lap belt portion should be
placed as low and snugly as possible on
the hips, not across the abdomen. For
specific recommendations, consult a
physician.
WARNING - Pregnant
women
Pregnant women must never place
the lap portion of the safety belt
over the area of the abdomen
where the unborn child is located
or above the abdomen where the
belt could seriously injure or even
cause the death of the unborn child
during an impact.
I
nf
or
mat
i
onPr
ovi
dedby:
Injured person
A seat belt should be used when an
injured person is being transported.
When this is necessary, you should consult a physician for recommendations.
One person per belt
Two people (including children) should
never attempt to use a single seat belt.
This could increase the severity of
injuries in case of an accident.
Do not lie down
To reduce the chance of injuries in the
event of an accident and to achieve maximum effectiveness of the restraint system, all passengers should be sitting up
and the front and rear seats should be in
an upright position when the car is moving. A seat belt cannot provide proper
protection if the person is lying down in
the rear seat or if the seats are in a
reclined position.
Safety features of your vehicle
Care of seat belts
WARNING
Riding with a reclined seatback
increases your chance of serious
or fatal injuries in the event of a collision or sudden stop. The protection of your restraint system (seat
belts and air bags) is greatly
reduced by reclining your seat.
Seat belts must be snug against
your hips and chest to work properly. The more the seatback is
reclined, the greater the chance
that an occupant's hips will slide
under the lap belt causing serious
internal injuries or the occupant's
neck could strike the shoulder belt.
Drivers and passengers should
always sit well back in their seats,
properly belted, and with the seatbacks upright.
Seat belt systems should never be disassembled or modified. In addition, care
should be taken to assure that seat belts
and belt hardware are not damaged by
seat hinges, doors or other abuse.
WARNING
When you return the rear seatback
to its upright position after the rear
seatback was folded down, be careful not to damage the seat belt webbing or buckle. Be sure that the
webbing or buckle does not get
caught or pinched in the rear seat.
A seat belt with damaged webbing
or buckle will not be as strong and
could possibly fail during a collision or sudden stop, resulting in
serious injury.
I
nf
or
mat
i
onPr
ovi
dedby:
Periodic inspection
All seat belts should be inspected periodically for wear or damage of any kind.
Any damaged parts should be replaced
as soon as possible.
Keep belts clean and dry
Seat belts should be kept clean and dry.
If belts become dirty, they can be
cleaned by using a mild soap solution
and warm water. Bleach, dye, strong
detergents or abrasives should not be
used because they may damage and
weaken the fabric.
When to replace seat belts
Entire in-use seat belt assembly or
assemblies should be replaced if the
vehicle has been involved in an accident.
This should be done even if no damage
is visible. Additional questions concerning seat belt operation should be directed
to an authorized HYUNDAI dealer.
3 25
Safety features of your vehicle
CHILD RESTRAINT SYSTEM
Children riding in the car should sit in the
rear seat and must always be properly
restrained to minimize the risk of injury in
an accident, sudden stop or sudden
maneuver. According to accident statistics, children are safer when properly
restrained in the rear seats than in the
front seat. Larger children not in a child
restraint should use one of the seat belts
provided.
You should be aware of the specific
requirements in your state. Child and/or
infant safety seats must be properly
placed and installed in the rear seat. You
must use a commercially available child
restraint system that meets the requirements of the Federal Motor Vehicle Safety
Standards (FMVSS).
Child restraint systems are designed to be
secured in vehicle seats by lap belts or the
lap belt portion of a lap/shoulder belt, or
by a LATCH system (if equipped).
Children could be injured or killed in a
crash if their restraints are not properly
secured. For small children and babies, a
child seat or infant seat must be used.
Before buying a particular child restraint
system, make sure it fits your car seat
and seat belts, and fits your child. Follow
all the instructions provided by the manufacturer when installing the child
restraint system.
3 26
WARNING
• A child restraint system must be
placed in the rear seat. Never
install a child or infant seat on the
front passenger's seat. Should an
accident occur and cause the
passenger-side air bag to deploy,
it could severely injure or kill an
infant or child seated in an infant
or child seat. Thus only use a
child restraint in the rear seat of
your vehicle.
• A seat belt or child restraint system can become very hot if it is
left in a closed vehicle on a sunny
day, even if the outside temperature does not feel hot. Be sure to
check the seat cover and buckles
before placing a child there.
• When the child restraint system
is not in use, store it in the luggage area or fasten it with a seat
belt so that it will not be thrown
forward in the case of a sudden
stop or an accident.
• Children may be seriously injured
or killed by an inflating air bag.
All children, even those too large
for child restraints, must ride in
the rear seat.
I
nf
or
mat
i
onPr
ovi
dedby:
WARNING
To reduce the chance of serious or
fatal injuries:
• Children of all ages are safer
when restrained in the rear seat.
A child riding in the front passenger seat can be forcefully struck
by an inflating air bag resulting in
serious or fatal injuries.
• Always follow the child restraint
system manufacturer’s instructions for installation and use of
the child restraint.
• Always make sure the child seat
is secured properly in the car and
your child is securely restrained
in the child seat.
• Never hold a child in your arms or
lap when riding in a vehicle. The
violent forces created during a
crash will tear the child from your
arms and throw the child against
the car’s interior.
• Never put a seat belt over yourself and a child. During a crash,
the belt could press deep into the
child causing serious internal
injuries.
(Continued)
Safety features of your vehicle
(Continued)
• Never leave children unattended
in a vehicle – not even for a short
time. The car can heat up very
quickly, resulting in serious
injuries to children inside. Even
very young children may inadvertently cause the vehicle to move,
entangle themselves in the windows, or lock themselves or others inside the vehicle.
• Never allow two children, or any
two persons, to use the same
seat belt.
• Children often squirm and reposition themselves improperly.
Never let a child ride with the
shoulder belt under their arm or
behind their back. Always properly position and secure children in
the rear seat.
• Never allow a child to stand-up or
kneel on the seat or floor of a
moving vehicle. During a collision or sudden stop, the child
can be violently thrown against
the vehicle’s interior, resulting in
serious injury.
(Continued)
(Continued)
• Never use an infant carrier or a
child safety seat that "hooks"
over a seatback, it may not provide adequate security in an accident.
• Seat belts can become very hot,
especially when the car is parked
in direct sunlight. Always check
seat belt buckles before fastening them over a child.
• After an accident, have an authorized HYUNDAI dealer check the
child restraint system, seat belt,
tether anchor and lower anchor.
• If there is not enough space to
place the child restraint system
because of the driver's seat,
install the child restraint system
in the rear right seat.
Rearward-facing child restraint system
CRS09
Forward-facing child restraint system
ORB030026
Using a child restraint system
For small children and babies, the use of
a child seat or infant seat is required. This
child seat or infant seat should be of
appropriate size for the child and should
be installed in accordance with the manufacturer's instructions.
I
nf
or
mat
i
onPr
ovi
dedby:
3 27
Safety features of your vehicle
For safety reasons, we recommend that
the child restraint system be used in the
rear seats.
WARNING
Never place a rear-facing child
restraint in the front passenger
seat, because of the danger that an
inflating passenger-side air bag
could impact the rear-facing child
restraint and kill the child.
Since all passenger seat belts move
freely under normal conditions and only
lock under extreme or emergency conditions (emergency locking mode), you
must manually change these seat belts
to the automatic locking mode to secure
a child restraint.
3 28
WARNING - Child seat
installation
• A child can be seriously injured
or killed in a collision if the child
restraint is not properly anchored
to the vehicle and the child is not
properly restrained in the child
restraint. Before installing the
child restraint system, read the
instructions supplied by the child
restraint system manufacturer.
• If the seat belt does not operate
as described in this section, have
the system checked immediately
by your authorized HYUNDAI
dealer.
• Failure to observe this manual's
instructions regarding child
restraint systems and the
instructions provided with the
child restraint system could
increase the chance and/or
severity of injury in an accident.
I
nf
or
mat
i
onPr
ovi
dedby:
E2MS103005
Placing a passenger seat belt into
the automatic locking mode
The automatic locking mode will help
prevent the normal movement of the
child in the vehicle from causing the seat
belt to loosen and compromise the child
restraint system. To secure a child
restraint system, use the following procedure.
Safety features of your vehicle
OMD030053A
OMD030054A
OMD030055A
To install a child restraint system on the
outboard or center rear seats, do the following:
1. Place the child restraint system in the
seat and route the lap/shoulder belt
around or through the restraint, following the restraint manufacturer’s
instructions. Be sure the seat belt webbing is not twisted.
2. Fasten the lap/shoulder belt latch into
the buckle. Listen for the distinct “click”
sound.
Position the release button so that it is
easy to access in case of an emergency.
3. Pull the shoulder portion of the seat
belt all the way out. When the shoulder
portion of the seat belt is fully extended, it will shift the retractor to the
“Automatic locking” (child restraint)
mode.
4. Slowly allow the shoulder portion of
the seat belt to retract and listen for an
audible “clicking” or “ratcheting” sound.
This indicates that the retractor is in
the “automatic locking” mode. If no distinct sound is heard, repeat steps 3
and 4.
I
nf
or
mat
i
onPr
ovi
dedby:
3 29
Safety features of your vehicle
■ 4 Door
WARNING - Automatic
locking mode
OMD030056A
5. Remove as much slack from the belt
as possible by pushing down on the
child restraint system while feeding the
shoulder belt back into the retractor.
6. Push and pull on the child restraint
system to confirm that the seat belt is
holding it firmly in place. If it is not,
release the seat belt and repeat steps
2 through 6.
7. Double check that the retractor is in the
“Automatic locking” mode by attempting to pull more of the seat belt out of
the retractor. If you cannot, the retractor
is in the “Automatic locking” mode.
To remove the child restraint, press the
release button on the buckle and then
pull the lap/shoulder belt out of the
restraint and allow the seat belt to retract
fully.
3 30
The lap/shoulder belt automatically
returns to the “emergency lock
mode” whenever the belt is allowed
to retract fully. Therefore, the preceding seven steps must be followed each time a child restraint is
installed.
If the retractor is not in the
Automatic Locking mode, the child
restraint can move when your vehicle turns or stops suddenly. A child
can be seriously injured or killed if
the child restraint is not properly
anchored to the car, including setting the retractor to the Automatic
Locking mode.
When the seat belt is allowed to
retract to its fully stowed position, the
retractor will automatically switch
from the “Automatic locking” mode to
the emergency lock mode for normal
adult usage.
I
nf
or
mat
i
onPr
ovi
dedby:
ORB032024R
■ 5 Door
ORB031033L
Securing a child restraint seat with
“Tether Anchor” system
Child restraint hook holders are located
on the package tray or on the floor
behind the rear seats.
Safety features of your vehicle
WARNING
A child can be seriously injured or
killed in a collision if the child
restraint is not properly anchored
to the car and the child is not properly restrained in the child restraint.
Always follow the child seat manufacturer’s instructions for installation and use.
ORB030025
1. Route the child restraint seat strap
over the seatback.
For vehicles with adjustable headrests, route the tether strap under the
headrest and between the headrest
posts, otherwise route the tether strap
over the top of the seatback.
For more information about the use of
the headrests, refer to "Adjusting the
height up and down - Rear seat" in this
section.
2. Connect the tether strap hook to the
appropriate child restraint hook holder
and tighten to secure the child restraint
seat.
WARNING - Tether strap
Never mount more than one child
restraint to a single tether anchor
or to a single lower anchorage
point. The increased load caused
by multiple seats may cause the
tethers or anchorage points to
break, causing serious injury or
death.
I
nf
or
mat
i
onPr
ovi
dedby:
WARNING - Child restraint
check
Check that the child restraint system is secure by pushing and
pulling it in different directions.
Incorrectly fitted child restraints
may swing, twist, tip or separate
causing death or serious injury.
WARNING
- Child restraint anchorage
• Child restraint anchorages are
designed to withstand only those
loads imposed by correctly fitted
child restraints. Under no circumstances are they to be used for
adult seat belts or harnesses or
for attaching other items or
equipment to the vehicle.
• The tether strap may not work
properly if attached somewhere
other than the correct tether
anchor.
3 31
Safety features of your vehicle
WARNING
Lower Anchor
Lower Anchor
Position Indicator
B230D01NF
ORB030023
Securing a child restraint seat with
child seat lower anchor system
Some child seat manufacturers make
child restraint seats that are labeled as
LATCH or LATCH-compatible child
restraint seats. LATCH stands for "Lower
Anchors and Tethers for Children". These
seats include two rigid or webbing
mounted attachments that connect to
two LATCH anchors at specific seating
positions in your vehicle. This type of
child restraint seat eliminates the need to
use seat belts to attach the child seat in
the rear seats.
Child restraint symbols are located on
the left and right rear seat backs to indicate the position of the lower anchors for
child restraints.
3 32
I
nf
or
mat
i
onPr
ovi
dedby:
• When using the vehicle's
"LATCH" system to install a child
restraint system in the rear seat,
all unused vehicle rear seat belt
metal latch plates or tabs must be
latched securely in their seat belt
buckles and the seat belt webbing must be retracted behind
the child restraint to prevent the
child from reaching and taking
hold of unretracted seat belts.
Unlatched metal latch plates or
tabs may allow the child to reach
the unretracted seat belts which
may result in strangulation and a
serious injury or death to the
child in the child restraint.
• Do not place anything around the
lower anchors. Also make sure
that the seat belt is not caught in
the lower anchors.
Safety features of your vehicle
LATCH anchors have been provided in
your vehicle. The LATCH anchors are
located in the left and right outboard rear
seating positions. Their locations are
shown in the illustration. There is no
LATCH anchor provided for the center
rear seating position.
The LATCH anchors are located between
the seatback and the seat cushion of the
rear seat left and right outboard seating
positions.
Follow the child seat manufacturer’s
instructions to properly install child
restraint seats with LATCH or LATCHcompatible attachments.
Once you have installed the LATCH child
restraint, assure that the seat is properly
attached to the LATCH and tether
anchors.
Also, test the child restraint seat before
you place the child in it. Tilt the seat from
side to side. Also try to tug the seat forward. Check to see if the anchors hold
the seat in place.
CAUTION
Do not allow the rear seat belt webbing to get scratched or pinched by
the child-seat latch and LATCH
anchor during the installation.
WARNING
If the child restraint is not anchored
properly, the risk of a child being
seriously injured or killed in a collision greatly increases.
WARNING - LATCH lower
anchors
LATCH lower anchors are only to
be used with the left and right rear
outboard seating positions. Never
attempt to attach a LATCH
equipped seat in the center seating
position. You may damage the
anchors or the anchors may fail
and break in a collision.
I
nf
or
mat
i
onPr
ovi
dedby:
3 33
Safety features of your vehicle
AIR BAG - ADVANCED SUPPLEMENTAL RESTRAINT SYSTEM
(1)
(2)
(3)
(4)
Driver’s front air bag
Passenger’s front air bag
Side impact air bag
Curtain air bag
WARNING
Even in vehicles with air bags, you
and your passengers must always
wear the seat belts provided in
order to minimize the risk and
severity of injury in the event of a
collision or rollover.
❈ The actual air bags in the vehicle may differ from the illustration.
OYF039050
3 34
I
nf
or
mat
i
onPr
ovi
dedby:
Safety features of your vehicle
How does the air bag system
operate
• Air bags are activated (able to inflate if
necessary) only when the ignition
switch is turned to the ON or START
position.
• Air bags inflate instantly in the event of
serious frontal or side collision in order
to help protect the occupants from serious physical injury.
• There is no single speed at which the
air bags will inflate.
Generally, air bags are designed to
inflate by the severity of a collision and
its direction. These two factors determine whether the sensors send out an
electronic deployment/ inflation signal.
• Air bag deployment depends on a
number of factors including vehicle
speed, angles of impact and the density and stiffness of the vehicles or
objects which your vehicle hits in the
collision. Though, factors are not limited to those mentioned above.
• The front air bags will completely
inflate and deflate in an instant.
It is virtually impossible for you to see
the air bags inflate during an accident.
It is much more likely that you will simply see the deflated air bags hanging
out of their storage compartments after
the collision.
• In order to help provide protection in a
severe collision, the air bags must
inflate rapidly. The speed of air bag
inflation is a consequence of the
extremely short time in which a collision
occurs and the need to get the air bag
between the occupant and the vehicle
structures before the occupant impacts
those structures. This speed of inflation
reduces the risk of serious or lifethreatening injuries in a severe collision
and is thus a necessary part of air bag
design.
However, air bag inflation can also
cause injuries which normally can
include facial abrasions, bruises and
broken bones because the inflation
speed also causes the air bags to
expand with a great deal of force.
• There are even circumstances
under which contact with the air bag
can cause fatal injuries, especially if
the occupant is positioned excessively close to the air bag.
I
nf
or
mat
i
onPr
ovi
dedby:
WARNING
• To avoid severe personal injury
or death caused by deploying air
bags in a collision, the driver
should sit as far back from the
steering wheel air bag as possible (at least 10 inches (250 mm)
away). The front passengers
should always move their seats
as far back as possible and sit
back in their seat.
• Air bags inflate instantly in the
event of collision, and passengers may be injured by the air bag
expansion force if they are not in
proper position.
• Air bag inflation may cause
injuries which normally include
facial or bodily abrasions,
injuries from broken glasses or
burns by the air bag inflation
gasses.
3 35
Safety features of your vehicle
Noise and smoke
When the air bags inflate, they make a
loud noise and they leave smoke and
powder in the air inside of the vehicle.
This is normal and is a result of the ignition of the air bag inflator. After the air
bag inflates, you may feel substantial discomfort in breathing due to the contact of
your chest with both the seat belt and the
air bag, as well as from breathing the
smoke and powder. Open your doors
and/or windows as soon as possible
after impact in order to reduce discomfort and prevent prolonged exposure to the smoke and powder.
Though the smoke and powder are nontoxic, they may cause irritation to the skin
(eyes, nose and throat, etc). If this is the
case, wash and rinse with cold water
immediately and consult a doctor if the
symptom persists.
WARNING
When the air bags deploy, the air
bag related parts in the steering
wheel and/or instrument panel
and/or in both sides of the roof rails
above the front and rear doors are
very hot. To prevent injury, do not
touch the air bag storage area’s
internal components immediately
after an air bag has inflated.
3 36
WARNING
1JBH3051
Do not install a child restraint on the
front passenger’s seat.
Never place a rear-facing child restraint
in the front passenger’s seat. If the air
bag deploys, it would impact the rear-facing child restraint, causing serious or
fatal injury.
In addition, do not place front-facing child
restraints in the front passenger’s seat
either. If the front passenger air bag
inflates, it could cause serious or fatal
injuries to the child.
I
nf
or
mat
i
onPr
ovi
dedby:
• Extreme Hazard! Do not use a
rearward facing child restraint on
a seat protected by an air bag in
front of it!
• Never put a child restraint in the
front passenger’s seat. If the front
passenger air bag inflates, it
would cause serious or fatal
injuries.
• When children are seated in the
rear outboard seats of a vehicle
equipped with side and/or curtain
air bags, be sure to install the
child restraint system as far away
from the door side as possible,
and securely lock the child
restraint system in position.
Inflation of side and/or curtain air
bags could cause serious injury
or death to an infant or child.
Safety features of your vehicle
W7-147
When the ignition switch is turned ON,
the indicator light should illuminate for
approximately 6 seconds, then go off.
Have the system checked if:
• The light does not turn on briefly when
you turn the ignition ON.
• The light stays on after illuminating for
approximately 6 seconds.
• The light comes on while the vehicle is
in motion.
• The light blinks when the ignition
switch is in ON position.
OMD030050N
SRS components and functions
C041000AUN
Air bag warning light
The SRS consists of the following components:
1. Driver's front air bag module
2. Passenger's front air bag module
3. Side impact air bag modules
4. Curtain air bag modules
5. Retractor pre-tensioner assemblies
6. Air bag warning light
7. SRS control module (SRSCM)
8. Front impact sensors
9. Side impact sensors
10. PASS AIR BAG “OFF” indicator
(Front passenger’s seat only)
11. Occupant detection system (Front
passenger’s seat only)
The purpose of air bag warning light in
your instrument panel is to alert you of a
potential problem with your air bag Supplemental Restraint System (SRS).
I
nf
or
mat
i
onPr
ovi
dedby:
3 37
Safety features of your vehicle
12. Driver’s and front passenger’s seat
belt buckle sensors
13. Anchor pre-tensioner
14. Side pressure sensor
WARNING
The SRSCM continually monitors all
SRS components while the ignition
switch is ON to determine if a crash
impact is severe enough to require air
bag deployment or pre-tensioner seat
belt deployment.
W7-147
The SRS air bag warning light " " on the
instrument panel will illuminate for about 6
seconds after the ignition switch is turned
to the ON position, after which the SRS air
bag warning light " " should go out.
3 38
I
nf
or
mat
i
onPr
ovi
dedby:
If any of the following conditions
occurs, this indicates a malfunction
of the SRS. Have an authorized
HYUNDAI dealer inspect the air bag
system as soon as possible.
• The light does not turn on briefly
when you turn the ignition ON.
• The light stays on after illuminating for approximately 6 seconds.
• The light comes on while the
vehicle is in motion.
• The light blinks when the ignition
switch is in ON position.
Safety features of your vehicle
Driver’s front air bag (1)
Driver’s front air bag (2)
Driver’s front air bag (3)
B240B01L
B240B02L
B240B03L
The front air bag modules are located
both in the center of the steering wheel
and in the front passenger's panel above
the glove box. When the SRSCM detects
a sufficiently severe impact to the front of
the vehicle, it will automatically deploy
the front air bags.
Upon deployment, tear seams molded
directly into the pad covers will separate
under pressure from the expansion of the
air bags. Further opening of the covers
then allows full inflation of the air bags.
A fully inflated air bag, in combination
with a properly worn seat belt, slows the
driver's or the passenger's forward
motion, reducing the risk of head and
chest injury.
After complete inflation, the air bag
immediately starts deflating, enabling the
driver to maintain forward visibility and
the ability to steer or operate other controls.
I
nf
or
mat
i
onPr
ovi
dedby:
3 39
Safety features of your vehicle
Passenger’s front air bag
WARNING
B240B05L
WARNING
• Do not install or place any accessories (drink holder, CD or discs
holder, sticker, etc.) on the front
passenger's panel above the
glove box in a vehicle with a passenger's air bag. Such objects
may become dangerous projectiles and cause injury if the passenger's air bag inflates.
• When installing a container of liquid air freshener inside the vehicle, do not place it near the
instrument cluster nor on the
instrument panel surface.
It may become a dangerous projectile and cause injury if the passenger's air bag inflates.
3 40
• If an air bag deploys, there may
be a loud noise followed by a fine
dust released in the vehicle.
These conditions are normal and
are not hazardous - the air bags
are packed in this fine powder.
The dust generated during air
bag deployment may cause skin
or eye irritation as well as aggravate asthma for some persons.
Always wash all exposed skin
areas thoroughly with lukewarm
water and a mild soap after an
accident in which the air bags
were deployed.
• The SRS can function only when
the ignition switch is in the ON
position. If the SRS air bag warning light " " does not illuminate, or continuously remains on
after illuminating for about 6 seconds when the ignition switch is
turned to the ON position, or after
the engine is started, comes on
while driving, the SRS is not
working properly. If this occurs,
have your vehicle immediately
inspected by an authorized
HYUNDAI dealer.
(Continued)
I
nf
or
mat
i
onPr
ovi
dedby:
(Continued)
• Before you replace a fuse or disconnect a battery terminal, turn
the ignition switch to the LOCK
position and remove the ignition
key for ignition key, and turn the
engine start/stop button to the
OFF position for smart key. Never
remove or replace the air bag
related fuse(s) when the ignition
switch is in the ON position.
Failure to heed this warning will
cause the SRS air bag warning
light to illuminate.
Safety features of your vehicle
Main components of occupant
detection system
ORB031034N
Occupant detection system
Your vehicle is equipped with an occupant detection system in the front passenger's seat.
The occupant detection system is
designed to detect the presence of a
properly-seated front passenger and
determine if the passenger's front air bag
should be enabled (may inflate) or not.
The driver's front air bag is not affected
or controlled by the occupant detection
system.
• A detection device located within the
front passenger seat.
• Electronic system to determine whether
the front passenger air bag system
should be activated or deactivated.
• A warning light located on the instrument panel which illuminates the words
PASSENGER AIR BAG "OFF" indicating the front passenger air bag system
is deactivated.
• The instrument panel air bag warning
light is interconnected with the occupant
detection system.
If the front passenger seat is occupied by
a person that the system determines to be
of adult size, and he/she sits properly (sitting upright with the seatback in an upright
position, centered on the seat cushion
with their seat belt on, legs comfortably
extended and their feet on the floor), the
PASSENGER AIR BAG "OFF" indicator
will be turned off and the front passenger's air bag will be able to inflate, if necessary, in frontal crashes.
You will find the PASS AIR BAG "OFF"
indicator on the center facia panel. This
system detects the conditions 1~4 in the
following table and activates or deactivates the front passenger air bag based
on these conditions.
Always be sure that you and all vehicle
occupants are seated and restrained
properly (sitting upright with the seat in
an upright position, centered on the seat
cushion, with the person's legs comfortably extended, feet on the floor, and
wearing the safety belt properly) for the
most effective protection by the air bag
and the safety belt.
WARNING
Do not put anything in front of the
passenger air bag off indicator.
I
nf
or
mat
i
onPr
ovi
dedby:
3 41
Safety features of your vehicle
• The ODS may not function properly if
the passenger takes actions which can
affect the detection system. These
include:
(1) Failing to sit in an upright position.
(2) Leaning against the door or center
console.
(3) Sitting towards the sides or the
front of the seat.
(4) Putting legs on the dashboard or
resting them on other locations.
(5) Improperly wearing the safety belt.
(6) Reclining the seat back.
(7) Unauthorized replacement of seat
cover.
(8) Covering seat with blanket
3 42
Condition and operation in the front passenger occupant detection system
Condition detected by the
occupant detection
system
Indicator/Warning light
Devices
"PASSENGER AIR
BAG OFF" indicator
light
SRS warning light
1. Adult or child*1
Off
Off
Activated
2. Child restraint system*2
On
On
Off
Off
Deactivated
Deactivated
Off
On
Activated
3. Unoccupied
4. There is a malfunction
in the system
*1) The ODS system uses a field to evaluate a person's size to determine
whether the air bag should deploy. It
is possible for a child to be detected
and activate the ODS, thus allowing
the airbag to deploy. To maximize
safety, do not allow children to ride in
the front passenger seat.
*2) Never install a child restraint system
on the front passenger seat.
I
nf
or
mat
i
onPr
ovi
dedby:
Front passenger
air bag
WARNING
Riding in an improper position or
placing weight on the front passenger's seat when it is unoccupied by
a passenger adversely affects the
Occupant Detection System (ODS).
Your ODS is designed to resist
electronic waves, but do not place
an electronic device such as laptop
computer on or near the seat cushion since it may defeat the proper
functioning of the ODS.
(Continued)
Safety features of your vehicle
(Continued)
OVQ036013N
1KMN3663
1KMN3665
- Never put a heavy load, an active
electronic device or blanket in
the front passenger seat or seatback pocket.
- Never sit with hips shifted
towards the front of the seat.
- Never place feet on the dashboard.
1KMN3662
1KMN3664
OVQ036014N
- Never excessively recline the
front passenger seatback.
- Never lean on the door or center
console.
- Never sit on one side of the front
passenger seat.
- Never place feet on the front passenger seatback.
I
nf
or
mat
i
onPr
ovi
dedby:
3 43
Safety features of your vehicle
Proper position
WARNING
B990A01O
When an adult is seated in the front passenger seat, if the PASS AIR BAG “OFF”
indicator is on, turn the ignition switch to
the LOCK or OFF position and ask the
passenger to sit properly (sitting upright
with the seat back in an upright position,
centered on the seat cushion with their
seat belt on, legs comfortably extended
and their feet on the floor). Restart the
engine and have the person remain in
that position. This will allow the system to
detect the person and to enable the passenger air bag.
If the PASS AIR BAG "OFF" indicator is
still on, ask the passenger to move to the
rear seat.
3 44
Do not allow an adult passenger to
ride in the front seat when the PASS
AIR BAG “OFF” indicator is illuminated because the air bag will not
deploy in the event of a crash. If the
PASS AIR BAG "OFF" indicator
remains illuminated after the adult
passenger repositions themselves
properly and the car is restarted, it
is recommended that passenger
move to the rear seat because the
passenger's front air bag will not
deploy.
Front seat passengers must stay
properly seated to avoid serious
injury from a deploying air bag.
✽ NOTICE
The PASS AIR BAG "OFF" indicator
illuminates for about 4 seconds after the
ignition switch is turned to the ON position or after the engine is started. If the
front passenger seat is occupied, the
occupant detection sensor will then classify the front passenger after several
more seconds.
I
nf
or
mat
i
onPr
ovi
dedby:
WARNING
Do not put a heavy load in the front
passenger seatback pocket or on the
front passenger seat. Do not hang
onto the front passenger seat. Do not
hang any items, such as a seatback
table, on the front passenger seatback. Do not place feet on the front
passenger seatback. Do not place
any items under the front passenger
seat. Any of these could interfere
with proper sensor operation.
WARNING
• Even though your vehicle is
equipped with the occupant
detection system, never install a
child restraint system in the front
passenger's seat. A deploying air
bag can forcefully strike a child
resulting in serious injuries or
death. Any child age 12 and
under should ride in the rear seat.
Children too large for child
restraints should use the available lap/shoulder belts. No matter what type of crash, children of
all ages are safer when restrained
in the rear seat.
(Continued)
Safety features of your vehicle
(Continued)
• If the PASS AIR BAG "OFF" indicator is illuminated when the
front passenger's seat is occupied by an adult and he/she sits
properly (sitting upright with the
seatback in an upright position,
centered on the seat cushion
with their seat belt on, legs comfortably extended and their feet
on the floor), have that person sit
in the rear seat.
• Do not modify or replace the front
passenger seat. Don't place anything on or attach anything such
as a blanket or seat heater to the
front passenger seat. This can
adversely affect the occupant
detection system.
• Do not sit on sharp objects such
as tools when occupying the
front passenger seat. This can
adversely affect the occupant
detection system.
• Do not use accessory seat covers on the front seats.
(Continued)
(Continued)
• Accident statistics show that children are safer if they are
restrained in the rear, as opposed
to the front seat. It is recommended that child restraints be secured
in a rear seat, including an infant
riding in a rear-facing infant seat,
a child riding in a forward-facing
child seat and an older child riding in a booster seat.
• Air bags can only be used once –
have an authorized HYUNDAI
dealer replace the air bag immediately after deployment.
• The occupant detection system
may not work properly if water,
coffee or any other liquid including rain gets on the seat. Keep
the front seat dry at all times.
(Continued)
I
nf
or
mat
i
onPr
ovi
dedby:
(Continued)
• Do not place an electronic device
such as a laptop computer on the
front passenger seat. Its electronic field may cause the ODS to
switch to the "on" condition and
thus allow the passenger air bag
to deploy needlessly in a collision, increasing your repair costs.
• The adult or child in the front passenger’s seat who is not seated
correctly (for example: seat excessively reclined, leaning on the
door or center console, or hips
shifted forward in the seat) can
cause a condition where the occupant detection system senses
less field than if the occupant
were seated properly (sitting
upright with the seatback in an
upright position, centered on the
seat cushion with their seat belt
on, legs comfortably extended
and their feet on the floor).
This condition can result in an
adult potentially being misclassified as a child and illumination of
the PASS AIR BAG "OFF" indicator.
3 45
Safety features of your vehicle
Driver’s front air bag
Passenger’s front air bag
WARNING
If the occupant detection system is
not working properly, the SRS air
bag warning light
on the instrument panel will illuminate because
the passenger's front air bag is
connected with the occupant
detection system. If there is a malfunction of the occupant detection
system, the PASS AIR BAG "OFF"
indicator will not illuminate and the
passenger's front air bag will inflate
in frontal impact crashes even if
there is no occupant in the front
passenger's seat. If the SRS air bag
warning light does not illuminate
when the ignition switch is turned
to the ON position, remains illuminated after approximately 6 seconds when the ignition switch is
turned to the ON position, or if it
illuminates while the vehicle is
being driven, have an authorized
HYUNDAI dealer inspect the occupant detection system and the SRS
air bag system as soon as possible.
3 46
ORB030010
ORB030011
Driver's and passenger's front air
bag
The purpose of the SRS is to provide the
vehicle's driver and/or the front passenger with additional protection than that
offered by the seat belt system alone in
case of a frontal impact of sufficient
severity. The SRS uses sensors to gather
information about the driver's seat position, the driver's and front passenger's
seat belt usage and impact severity.
Your vehicle is equipped with an
Advanced Supplemental Restraint (Air
Bag) System and lap/shoulder belts at
both the driver and passenger seating
positions. The indications of the system's
presence are the letters "SRS AIR BAG"
or “AIR BAG" embossed on the air bag
pad cover in the steering wheel and the
passenger's side front panel pad above
the glove box.
The SRS consists of air bags installed
under the pad covers in the center of the
steering wheel and the passenger's side
front panel above the glove box.
I
nf
or
mat
i
onPr
ovi
dedby:
Safety features of your vehicle
WARNING
If the occupant detection system is
not working properly, the SRS air
bag warning light
on the instrument panel will illuminate because
the SRS air bag warning light is
connected with the occupant
detection system. If the SRS air bag
warning light does not illuminate
when the ignition switch is turned
to the ON position, remains illuminated after approximately 6 seconds when the ignition switch is
turned to the ON position, or if it
illuminates while the vehicle is
being driven, have an authorized
HYUNDAI dealer inspect the
advanced SRS air bag system as
soon as possible.
The seat belt buckle sensors determine if
the driver and front passenger's seat
belts are fastened. These sensors provide the ability to control the SRS deployment based on whether or not the seat
belts are fastened, and how severe the
impact is.
The advanced SRS offers the ability to
control the air bag inflation within two levels. A first stage level is provided for moderate-severity impacts. A second stage
level is provided for more severe impacts.
According to the impact severity and seat
belt usage, the SRSCM (SRS Control
Module) controls the air bag inflation.
Failure to properly wear seat belts can
increase the risk or severity of injury in
an accident.
I
nf
or
mat
i
onPr
ovi
dedby:
Additionally, your vehicle is equipped
with an occupant detection system in the
front passenger's seat. The occupant
detection system detects the presence of
a passenger in the front passenger's seat
and will turn off the front passenger's air
bag under certain conditions. For more
detail, see "Occupant detection system"
in this section.
WARNING
Do not place any objects underneath the front seats as they could
interfere with the occupant detection system.
3 47
Safety features of your vehicle
WARNING
If you are considering modification
of your vehicle due to a disability,
please contact the Hyundai
Customer Assistance Center at 1800-633-5151.
✽ NOTICE
• Be sure to read information about the
SRS on the labels provided on the sun
visor.
• Advanced air bags are combined with
pre-tensioner seat belts to help provide enhanced occupant protection in
frontal crashes. Front air bags are not
intended to deploy in collisions in
which protection can be provided by
the pre-tensioner seat belt.
3 48
WARNING
Always use seat belts and child
restraints – every trip, every time,
everyone! Air bags inflate with considerable force and in the blink of
an eye. Seat belts help keep occupants in proper position to obtain
maximum benefit from the air bag.
Even with advanced air bags,
improperly and unbelted occupants
can be severely injured when the
air bag inflates. Always follow the
precautions about seat belts, air
bags and occupant safety contained in this manual.
To reduce the chance of serious or
fatal injuries and receive the maximum safety benefit from your
restraint system:
• Never place a child in any child or
booster seat in the front seat.
• ABC – Always Buckle Children in
the back seat. It is the safest
place for children of any age to
ride.
• Front and side air bags can injure
occupants improperly positioned
in the front seats.
(Continued)
I
nf
or
mat
i
onPr
ovi
dedby:
(Continued)
• Move your seat as far back as
practical from the front air bags,
while still maintaining control of
the vehicle.
• You and your passengers should
never sit or lean unnecessarily
close to the air bags. Improperly
positioned driver and passengers
can be severely injured by inflating air bags.
• Never lean against the door or
center console – always sit in an
upright position.
• Do not allow a passenger to ride
in the front seat when the PASS
AIR BAG "OFF" indicator is illuminated, because the air bag will
not deploy in the event of a moderate or severe frontal crash.
(Continued)
Safety features of your vehicle
(Continued)
• No objects should be placed over
or near the air bag modules on
the steering wheel, instrument
panel, and the front passenger's
panel above the glove box,
because any such object could
cause harm if the vehicle is in a
crash severe enough to cause
the air bags to deploy.
• Never place covers, blankets or
seat warmers on the passenger
seat as these may interfere with
the occupant detection system.
• Do not tamper with or disconnect
SRS wiring or other components
of the SRS system. Doing so
could result in injury, due to accidental deployment of the air bags
or by rendering the SRS inoperative.
• If the SRS air bag warning light
remains illuminated while the
vehicle is being driven, have an
authorized HYUNDAI dealer
inspect the air bag system as
soon as possible.
(Continued)
(Continued)
• Air bags can only be used once –
have an authorized HYUNDAI
dealer replace the air bag immediately after deployment.
• The SRS is designed to deploy
the front air bags only when an
impact is sufficiently severe and
when the impact angle is less
than 30° from the forward longitudinal axis of the vehicle.
Additionally, the air bags will only
deploy once. Seat belts must be
worn at all times.
• Front air bags are not intended to
deploy in side-impact, rearimpact or rollover crashes. In
addition, front air bags will not
deploy in frontal crashes below
the deployment threshold.
(Continued)
I
nf
or
mat
i
onPr
ovi
dedby:
(Continued)
• Even though your vehicle is
equipped with the occupant
detection system, do not install a
child restraint system in the front
passenger seat position. A child
restraint system must never be
placed in the front seat.The infant
or child could be severely injured
or killed by an air bag deployment
in case of an accident.
• Children age 12 and under must
always be properly restrained in
the rear seat. Never allow children to ride in the front passenger seat. If a child over 12 must
be seated in the front seat, he or
she must be properly belted and
the seat should be moved as far
back as possible.
• For maximum safety protection in
all types of crashes, all occupants including the driver should
always wear their seat belts
whether or not an air bag is also
provided at their seating position
to minimize the risk of severe
injury or death in the event of a
crash. Do not sit or lean unnecessarily close to the air bag while
the vehicle is in motion.
(Continued)
3 49
Safety features of your vehicle
(Continued)
• Sitting improperly or out of position can result in serious or fatal
injury in a crash. All occupants
should sit upright with the seatback in an upright position, centered on the seat cushion with
their seat belt on, legs comfortably extended and their feet on
the floor until the vehicle is
parked and the ignition key is
removed.
• The SRS air bag system must
deploy very rapidly to provide
protection in a crash. If an occupant is out of position because of
not wearing a seat belt, the air
bag may forcefully contact the
occupant causing serious or fatal
injuries.
The side impact air bags are designed to
deploy only during certain side-impact
collisions, depending on the crash severity, angle, speed and point of impact. The
side impact air bags are not designed to
deploy in all side impact situations.
Front
WARNING
ORBC030021
OTF030036
Side impact air bag
Your vehicle is equipped with a side
impact air bag in each front seat. The
purpose of the air bag is to provide the
vehicle's driver and/or the front passenger with additional protection than that
offered by the seat belt alone.
3 50
I
nf
or
mat
i
onPr
ovi
dedby:
Do not allow the passengers to lean
their heads or bodies onto doors,
put their arms on the doors, stretch
their arms out of the window, or
place objects between the doors
and passengers when they are
seated on seats equipped with side
and/or curtain air bags.
Safety features of your vehicle
WARNING
• The side impact air bag is supplemental to the driver's and the
passenger's seat belt systems
and is not a substitute for them.
Therefore your seat belts must be
worn at all times while the vehicle
is in motion. The air bags deploy
only in certain side impact conditions severe enough to cause
significant injury to the vehicle
occupants.
• For best protection from the side
impact air bag system and to
avoid being injured by the
deploying side impact air bag,
both front seat occupants should
sit in an upright position with the
seat belt properly fastened. The
driver's hands should be placed
on the steering wheel at the 9:00
and 3:00 positions. The passenger's arms and hands should be
placed on their laps.
• Do not use any accessory seat
covers.
(Continued)
(Continued)
• Use of seat covers could reduce
or prevent the effectiveness of
the system.
• Do not install any accessories on
the side or near the side air bag.
• Do not place any objects over the
air bag or between the air bag
and yourself.
• Do not place any objects (an
umbrella, bag, etc.) between the
front door and the front seat.
Such objects may become dangerous projectiles and cause
injury if the supplemental side air
bag inflates.
• To prevent unexpected deployment of the side impact air bag
that may result in personal injury,
avoid impact to the side impact
sensor when the ignition switch
is on.
• If the seat or seat cover is damaged, have the vehicle checked
and repaired by an authorized
HYUNDAI dealer because your
vehicle is equipped with side
impact air bags and an occupant
detection system.
I
nf
or
mat
i
onPr
ovi
dedby:
OYF039058N
Curtain air bag
Curtain air bags are located along both
sides of the roof rails above the front and
rear doors.
They are designed to help protect the
heads of the front seat occupants and
the rear outboard seat occupants in certain side impact collisions.
3 51
Safety features of your vehicle
The curtain air bags are designed to
deploy only during certain side impact
collisions, depending on the crash severity, angle, speed and impact. The curtain
air bags are not designed to deploy in all
side impact situations, collisions from the
front or rear of the vehicle or in most
rollover situations.
3 52
WARNING
• In order for side and curtain air
bags to provide the best protection, front seat occupants and
outboard rear occupants should
sit in an upright position with the
seat belts properly fastened.
Importantly, children should sit in
a proper child restraint system in
the rear seat.
• When children are seated in the
rear outboard seats, they must be
seated in the proper child
restraint system. Make sure to
put the child restraint system as
far away from the door side as
possible, and secure the child
restraint system in a locked position.
• Do not allow the passengers to
lean their heads or bodies onto
doors, put their arms on the
doors, stretch their arms out of
the window, or place objects
between the doors and passengers when they are seated on
seats equipped with side and/or
curtain air bags.
(Continued)
I
nf
or
mat
i
onPr
ovi
dedby:
(Continued)
• Never try to open or repair any
components of the side curtain
air bag system. This should only
be done by an authorized
HYUNDAI dealer.
Failure to follow the above instructions can result in injury or death to
the vehicle occupants in an accident.
Safety features of your vehicle
Why didn’t my air bag go off in a
collision? (Inflation and non-inflation conditions of the air bag)
There are many types of accidents in
which the air bag would not be expected to provide additional protection.
These include rear impacts, second or
third collisions in multiple impact
accidents, as well as low speed
impacts.
ORB032013/ORB030014/ORB030015/OMD030039/ORB031018N
Air bag collision sensors
(1) SRS control module
(2) Front impact sensor
I
nf
or
mat
i
onPr
ovi
dedby:
(3) Side impact sensor
(4) Side pressure sensor
3 53
Safety features of your vehicle
WARNING
• Do not hit or allow any objects to
impact the locations where air
bags or sensors are installed.
This may cause unexpected air
bag deployment, which could
result in serious personal injury
or death.
• If the installation location or
angle of the sensors is altered in
any way, the air bags may deploy
when they should not or they may
not deploy when they should,
causing severe injury or death.
Therefore, do not try to perform
maintenance on or around the air
bag sensors. Have the vehicle
checked and repaired by an
authorized HYUNDAI dealer.
(Continued)
3 54
(Continued)
• Problems may arise if the sensor
installation angles are changed
due to the deformation of the
front bumper, body or B pillars or
front door where side collision
sensors are installed. Have the
vehicle checked and repaired by
an authorized HYUNDAI dealer.
• Your vehicle has been designed
to absorb impact and deploy the
air bag(s) in certain collisions.
Installing bumper guards or
replacing a bumper with non-genuine parts may adversely affect
your vehicle’s collision and air
bag deployment performance.
I
nf
or
mat
i
onPr
ovi
dedby:
1JBA3513
Air bag inflation conditions
Front air bags
Front air bags are designed to inflate in a
frontal collision depending on the intensity, speed or angles of impact of the front
collision.
Safety features of your vehicle
1JBA3514
Although the front air bags (driver’s and
front passenger’s air bags) are designed
to inflate only in frontal collisions, they
also may inflate in other types of collisions if the front impact sensors detect a
sufficient impact. Side impact and curtain
air bags are designed to inflate only in
side impact collisions, but they may
inflate in other collisions if the side
impact sensors detect a sufficient
impact.
If the vehicle chassis is impacted by
bumps or objects on unpaved roads, the
air bags may deploy. Drive carefully on
unpaved roads or on surfaces not
designed for vehicle traffic to prevent
unintended air bag deployment.
OMD030044
1JBA3515
Air bag non-inflation conditions
• In certain low-speed collisions the air
bags may not deploy. The air bags are
designed not to deploy in such cases
because they may not provide benefits
beyond the protection of the seat belts
in such collisions.
Side impact and curtain air bags
(if equipped)
Side impact and curtain air bags are
designed to inflate when an impact is
detected by side collision sensors
depending on the strength, speed or
angles of impact resulting from a side
impact collision.
I
nf
or
mat
i
onPr
ovi
dedby:
3 55
Safety features of your vehicle
OBH038058
1JBA3516
OBH038060
• Air bags are not designed to inflate in
rear collisions, because occupants are
moved backward by the force of the
impact. In this case, inflated air bags
would not be able to provide any additional benefit.
• Front air bags may not inflate in side
impact collisions, because occupants
move to the direction of the collision,
and thus in side impacts, frontal air bag
deployment would not provide additional occupant protection.
However, side impact and curtain air
bags may inflate depending on the
intensity, vehicle speed and angles of
impact.
• In an angled collision, the force of
impact may direct the occupants in a
direction where the air bags would not
be able to provide any additional benefit, and thus the sensors may not
deploy any air bags.
3 56
I
nf
or
mat
i
onPr
ovi
dedby:
Safety features of your vehicle
1JBA3517
1JBA3522
1JBA3518
• Just before impact, drivers often brake
heavily. Such heavy braking lowers the
front portion of the vehicle causing it to
“ride” under a vehicle with a higher
ground clearance. Air bags may not
inflate in this "under-ride" situation
because deceleration forces that are
detected by sensors may be significantly reduced by such “under-ride”
collisions.
• Front air bags do not inflate in rollover
accidents. However, side impact and
curtain air bags may inflate in a
rollover, when it is detected by the
rollover sensor.
• Air bags may not inflate if the vehicle
collides with objects such as utility
poles or trees, where the point of
impact is concentrated to one area and
the deceleration forces are significantly reduced.
I
nf
or
mat
i
onPr
ovi
dedby:
3 57
Safety features of your vehicle
SRS Care
The SRS is virtually maintenance-free
and so there are no parts you can safely
service by yourself. If the SRS air bag
warning light " " does not illuminate,
when you turn the ignition on, or continuously remains on, have your vehicle
immediately inspected by an authorized
HYUNDAI dealer.
Any work on the SRS system, such as
removing, installing, repairing, or any
work on the steering wheel, the front
passenger's panel, front seats and roof
rails must be performed by an authorized
HYUNDAI dealer. Improper handling of
the SRS system may result in serious
personal injury.
3 58
WARNING
• Modification to SRS components
or wiring, including the addition
of any kind of badges to the pad
covers or modifications to the
body structure, can adversely
affect SRS performance and lead
to possible injury.
• Not only the modification of the
parts where the SRS sensors are
but also the modification of other
parts of the vehicle may affect the
SRS performance and lead to
possible injury.
• For cleaning the air bag pad covers, use only a soft, dry cloth or
one which has been moistened
with plain water. Solvents or
cleaners could adversely affect
the air bag covers and proper
deployment of the system.
• No objects should be placed over
or near the air bag modules on the
steering wheel, instrument panel,
and the front passenger's panel
above the glove box, because any
such object could cause harm if the
vehicle is in a crash severe enough
to cause the air bags to inflate.
(Continued)
I
nf
or
mat
i
onPr
ovi
dedby:
(Continued)
• If the air bags inflate, they must
be replaced by an authorized
HYUNDAI dealer.
• Do not tamper with or disconnect
SRS wiring, or other components
of the SRS system. Doing so
could result in injury, due to accidental inflation of the air bags or
by rendering the SRS inoperative.
• If components of the air bag system must be discarded, or if the
vehicle must be scrapped, certain
safety precautions must be
observed.
An
authorized
HYUNDAI dealer knows these
precautions and can give you the
necessary information. Failure to
follow these precautions and procedures could increase the risk
of personal injury.
• If your car was flooded and has
soaked carpeting or water on the
flooring, you shouldn't try to start
the engine; have the car towed to
an authorized HYUNDAI dealer.
Safety features of your vehicle
Additional safety precautions
• Never let passengers ride in the
cargo area or on top of a foldeddown back seat. All occupants should
sit upright, fully back in their seats with
their seat belts on and their feet on the
floor.
• Passengers should not move out of
or change seats while the vehicle is
moving. A passenger who is not wearing a seat belt during a crash or emergency stop can be thrown against the
inside of the vehicle, against other
occupants, or out of the vehicle.
• Each seat belt is designed to
restrain one occupant. If more than
one person uses the same seat belt,
they could be seriously injured or killed
in a collision.
• Do not use any accessories on seat
belts. Devices claiming to improve
occupant comfort or reposition the seat
belt can reduce the protection provided
by the seat belt and increase the
chance of serious injury in a crash.
• Passengers should not place hard
or sharp objects between themselves and the air bags. Carrying
hard or sharp objects on your lap or in
your mouth can result in injuries if an
air bag inflates.
• Keep occupants away from the air
bag covers. All occupants should sit
upright, fully back in their seats with
their seat belts on and their feet on the
floor. If occupants are too close to the
air bag covers, they could be injured if
the air bags inflate.
• Do not attach or place objects on or
near the air bag covers. Any object
attached to or placed on the front or
side air bag covers could interfere with
the proper operation of the air bags.
• Do not modify the front seats.
Modification of the front seats could
interfere with the operation of the supplemental restraint system sensing
components or side air bags.
• Do not place items under the front
seats. Placing items under the front
seats could interfere with the operation
of the supplemental restraint system
sensing components and wiring harnesses.
• Never hold an infant or child on your
lap. The infant or child could be seriously injured or killed in the event of a
crash. All infants and children should
be properly restrained in appropriate
child safety seats or seat belts in the
rear seat.
I
nf
or
mat
i
onPr
ovi
dedby:
WARNING
• Sitting improperly or out of position can cause occupants to be
shifted too close to a deploying
air bag, strike the interior structure or be thrown from the vehicle
resulting in serious injury or
death.
• Always sit upright with the seatback in an upright position, centered on the seat cushion with
your seat belt on, legs comfortably extended and your feet on
the floor.
• Be careful not to cause impact to
the doors when the ignition is
ON. The air bags may inflate.
Adding equipment to or modifying
your air bag-equipped vehicle
If you modify your vehicle by changing
your vehicle's frame, bumper system,
front end or side sheet metal or ride
height, this may affect the operation of
your vehicle's air bag system.
3 59
Safety features of your vehicle
OMD030040N
*
ORB030029
Air bag warning label
Air bag warning labels, some required by
the U.S. National Highway Traffic Safety
Administration (NHTSA), are attached to
alert the driver and passengers of potential risks of the air bag system.
3 60
I
nf
or
mat
i
onPr
ovi
dedby:
Keys / 4-3
Remote keyless entry / 4-4
Door locks / 4-7
Trunk / 4-12
Tailgate / 4-14
Windows / 4-16
Hood / 4-21
Features of your vehicle
Fuel filler lid / 4-23
Sunroof / 4-26
Steering wheel / 4-30
Mirrors / 4-32
Instrument cluster / 4-36
Hazard warning flasher / 4-52
Lighting / 4-52
Wipers and washers / 4-57
Interior light / 4-61
Defroster / 4-64
Manual climate control system / 4-65
Automatic climate control system / 4-74
Windshield defrosting and defogging / 4-81
Storage compartments / 4-84
I
nf
or
mat
i
onPr
ovi
dedby:
4
Interior features / 4-87
Exterior features / 4-92
Audio system / 4-94
4
Features of your vehicle
I
nf
or
mat
i
onPr
ovi
dedby:
Features of your vehicle
KEYS
Record your key number
Key operations
The key code number
is stamped on the key
code tag attached to
the key set. Should
you lose your keys,
this number will enable an authorized
HYUNDAI dealer to duplicate the keys
easily. Remove the key code tag and
store it in a safe place. Also, record the
key code number and keep it in a safe
and handy place, but not in the vehicle.
Used to start the engine, lock and unlock
the doors.
WARNING - Ignition key
Leaving children unattended in a
vehicle with the ignition key is dangerous even if the key is not in the
ignition switch. Children copy
adults and they could place the key
in the ignition switch. The ignition
key would enable children to operate power windows or other controls, or even make the vehicle
move, which could result in serious
bodily injury or even death. Never
leave the keys in your vehicle with
unsupervised children, when the
Engine is running.
I
nf
or
mat
i
onPr
ovi
dedby:
WARNING
Use only HYUNDAI original parts
for the ignition key in your vehicle.
If an aftermarket key is used, the
ignition switch may not return to
ON after START. If this happens,
the starter will continue to operate
causing damage to the starter
motor and possible fire due to
excessive current in the wiring.
4 3
Features of your vehicle
REMOTE KEYLESS ENTRY (IF EQUIPPED)
Also, if the lock button is pressed once
more within 4 seconds, the hazard warning lights will blink and the horn will sound
once to confirm that the door is locked.
However, if any door or trunk lid remains
open, the hazard warning lights (and/or
the horn) will not operate. But if all doors
and trunk lid are closed after the lock button is pressed, the hazard warning lights
will blink once.
ORB044381
OJB040008N
Unlock (2)
Driver's door is unlocked if the unlock
button is pressed once. The hazard
warning lights will blink twice to indicate
that the driver's door is unlocked. All
doors are unlocked if the unlock button is
pressed twice within 4 seconds.
The hazard warning lights will blink twice
again to indicate that all doors are
unlocked. If no doors are opened within
30 seconds after unlocking them, the
doors will automatically lock again.
Remote keyless entry system
operations
Lock (1)
All doors are locked if the lock button is
pressed. If all doors and trunk are closed,
the hazard warning lights will blink once to
indicate that all doors are locked.
4 4
I
nf
or
mat
i
onPr
ovi
dedby:
✽ NOTICE - Unlock mode conversion
(if equipped)
You can change the system to unlock all
doors by one pressing the unlock button
on the transmitter. If you want this feature (central door unlock mode), perform the following:
two stage unlock mode ↔ central door
unlock mode
The unlock mode is changed alternately
by pressing the lock button and unlock
button on the transmitter at the same time
for 5 seconds or more. The hazard warning lights will blink four times to indicate
that the mode conversion is completed.
Panic (3)
The horn sounds and hazard warning
lights flash for about 30 seconds if this
button is pressed for more than 1.5 second. To stop the horn and lights, press
any button except the trunk button on
the transmitter.
Features of your vehicle
Transmitter precautions
✽ NOTICE
The transmitter will not work if any of
following occur:
• The ignition key is in ignition switch.
• You exceed the operating distance
limit (about 90 feet [30 m]).
• The battery in the transmitter is
weak.
• Other vehicles or objects may be
blocking the signal.
• The weather is extremely cold.
• The transmitter is close to a radio
transmitter such as a radio station or
an airport which can interfere with
normal operation of the transmitter.
When the transmitter does not work
correctly, open and close the door with
the ignition key. If you have a problem
with the transmitter, contact an authorized HYUNDAI dealer.
(Continued)
(Continued)
If the transmitter is in close proximity to
your cell phone or smart phone, the signal from the transmitter could be
blocked by normal operation of your
cell phone or smart phone. This is especially important when the phone is
active such as making call, receiving
calls,
text
messaging,
and/or
sending/receiving emails. Avoid placing
the transmitter and your cell phone or
smart phone in the same pants or jacket
pocket and maintain adequate distance
between the two devices.
CAUTION
Keep the transmitter away from
water or any liquid. If the keyless
entry system is inoperative due to
exposure to water or liquids, it will
not be covered by your manufacturer’s vehicle warranty.
I
nf
or
mat
i
onPr
ovi
dedby:
This device complies with Part 15 of
the FCC rules.
Operation is subject to the following two
conditions:
1. This device may not cause harmful
interference, and
2. This device must accept any interference received, including interference
that may cause undesired operation.
WARNING
Changes or modifications not
expressly approved by the party
responsible for compliance could
void the user’s authority to operate
the equipment. If the keyless entry
system is inoperative due to
changes or modifications not
expressly approved by the party
responsible for compliance, it will
not be covered by your manufacturer’s vehicle warranty.
4 5
Features of your vehicle
CAUTION
1KMA2003
Battery replacement
The transmitter uses a 3 volt lithium battery which will normally last for several
years. When replacement is necessary,
use the following procedure.
1. Insert a slim tool into the slot and gently
pry open the transmitter center cover.
2. Replace the battery with a new battery
(CR2032). When replacing the battery,
make sure the battery position.
3. Install the battery in the reverse order
of removal.
• The transmitter is designed to
give you years of trouble-free
use, however it can malfunction if
exposed to moisture or static
electricity. If you are unsure how
to use your transmitter or replace
the battery, contact an authorized
HYUNDAI dealer.
• Using the wrong battery can cause
the transmitter to malfunction. Be
sure to use the correct battery.
• To avoid damaging the transmitter, don't drop it, get it wet, or
expose it to heat or sunlight.
For replacement transmitters, see an
authorized HYUNDAI dealer for transmitter reprogramming.
4 6
I
nf
or
mat
i
onPr
ovi
dedby:
WARNING
An inappropriately disposed battery can be harmful to the environment and
human health.
Dispose the battery according to
your local law(s) or regulation.
Features of your vehicle
DOOR LOCKS
Unlock
Lock
• Doors can also be locked and
unlocked with the transmitter.
• Once the doors are unlocked, they may
be opened by pulling the door handle.
• When closing the door, push the door
by hand. Make sure that the doors are
closed securely.
✽ NOTICE
OYF049006
Operating door locks from outside the vehicle
• Turn the key toward the rear of the
vehicle to unlock and toward the front
of the vehicle to lock.
• If you lock the door with a key, all vehicle doors will lock automatically.
(if equipped)
• From the driver’s door, turn the key
toward the rear of the vehicle once to
unlock the driver’s door and once more
within 4 seconds to unlock all doors.
(if equipped)
• In cold and wet climates, door locks
and door mechanisms may not work
properly due to freezing conditions.
• If the door is locked/unlocked multiple times in rapid succession with
either the vehicle key or door lock
switch, the system may stop operating
temporarily in order to protect the
circuit and prevent damage to system
components.
✽ NOTICE - Unlock mode conversion
(if equipped)
You can change the system to unlock all
doors by turning the key to the right once.
If you want this feature (central door
unlock mode), perform the following:
two stage unlock mode ↔ central door
unlock mode
The unlock mode is changed alternately
by pressing the lock button and unlock
button on the transmitter (if equipped) at
the same time for 5 seconds or more. The
hazard warning lights will blink four
times to indicate that the mode conversion
is completed.
WARNING
• If you don't close the door
securely, the door may open
again.
• Be careful that someone's body
and hands are not trapped when
closing the door.
I
nf
or
mat
i
onPr
ovi
dedby:
4 7
Features of your vehicle
• Front door cannot be locked if the ignition key is in the ignition switch and the
door is open. (if equipped)
WARNING - Door lock
Lock
Unlock
ORB040003
ORB040002L
• To lock a door without the key, push the
inside door lock button (1) or central
door lock switch (2) to the “Lock” position and close the door (3).
• If you lock the door with the central
door lock switch (2), all vehicle doors
will lock automatically.
✽ NOTICE
Always remove the ignition key, engage
the parking brake, close all windows
and lock all doors when leaving your
vehicle unattended.
4 8
Operating door locks from inside
the vehicle
With the door lock button
• To unlock a door, push the door lock
button (1) to the “Unlock” position. The
red mark (2) on the button will be visible.
• To lock a door, push the door lock button (1) to the “Lock” position. If the door
is locked properly, the red mark (2) on
the button will not be visible.
• To open a door, pull the door handle
(3) outward.
• If the inner door handle on either front
door is pulled when the door lock button is in the locked position, the door
(or all doors) will unlock and the door
will open. (if equipped)
I
nf
or
mat
i
onPr
ovi
dedby:
malfunction
If a power door lock ever fails to
function while you are in the vehicle, try one or more of the following
techniques to exit:
• Operate the door unlock feature
repeatedly (both electronic and
manual) while simultaneously
pulling on the door handle.
• Operate the other door locks and
handles, front and rear.
• Lower a front window and use the
key to unlock the door from outside.
Features of your vehicle
• When pushing down on the rear portion (2) of the switch, all vehicle doors
will unlock.
• If the key is in the ignition switch and
front door is open, the doors will not
lock even though the front portion (1)
of central door lock switch is pressed.
Driver’s door
WARNING - Doors
ORBC040004
Passenger's door
ORB041410N
With central door lock switch
(if equipped)
Operate by depressing the central door
lock switch.
• When pushing down on the front portion (1) of the switch, all vehicle doors
will lock.
• The doors should always be fully
closed and locked while the vehicle is in motion to prevent accidental opening of the door.
Locked doors will also discourage potential intruders when the
vehicle stops or slows.
• Be careful when opening doors
and watch for vehicles, motorcycles, bicycles or pedestrians
approaching the vehicle in the
path of the door. Opening a door
when something is approaching
can cause damage or injury.
I
nf
or
mat
i
onPr
ovi
dedby:
WARNING - Unlocked
vehicles
Leaving your vehicle unlocked can
invite theft or possible harm to you
or others from someone hiding in
your vehicle while you are gone.
Always remove the ignition key,
engage the parking brake, close all
windows and lock all doors when
leaving your vehicle unattended.
4 9
Features of your vehicle
WARNING - Unattended
children
An enclosed vehicle can become
extremely hot, causing death or
severe injury to unattended children or animals who cannot escape
the vehicle. Furthermore, children
might operate features of the vehicle that could injure them, or they
could encounter other harm, possibly from someone gaining entry to
the vehicle. Never leave children or
animals unattended in your vehicle.
4 10
Impact sensing door unlock system
(if equipped)
All doors will be automatically unlocked
when the impact is delivered to impact
sensors while the ignition switch is ON.
However, the doors may not be unlocked
if mechanical problems occur with the
door lock system or battery.
Speed sensing door lock system
(if equipped)
All doors will be automatically locked
after the vehicle speed exceeds 9 mph
(15 km/h). And all doors will be automatically unlocked when you turn the engine
off or when you remove the ignition key.
(if equipped)
I
nf
or
mat
i
onPr
ovi
dedby:
Auto door lock/unlock feature
(Automatic transaxle)
(if equipped)
• All doors will automatically lock when
the shift lever is moved out of P (Park).
• All doors will automatically unlock
when the shift lever is moved into P
(Park).
Features of your vehicle
3. Close the rear door.
To open the rear door, pull the outside
door handle (2).
Even though the doors may be unlocked,
the rear door will not open by pulling the
inner door handle until the rear door child
safety lock is unlocked.
WARNING - Rear door
locks
ORB040005
Child-protector rear door lock
The child safety lock is provided to help
prevent children from accidentally opening the rear doors from inside the vehicle.
The rear door safety locks should be
used whenever children are in the vehicle.
1. Open the rear door.
2. Push the child safety lock located on
the rear edge of the door to the “Lock”
position. When the child safety lock is
in the “Lock (
)” position, rear door
will not open even though the inner
door handle is pulled inside the vehicle.
If children accidentally open the
rear doors while the vehicle is in
motion, they could fall out of the
vehicle, resulting in severe injury or
death. To prevent children from
opening the rear doors from the
inside, the rear door safety locks
should be used whenever children
are in the vehicle.
I
nf
or
mat
i
onPr
ovi
dedby:
4 11
Features of your vehicle
TRUNK (4 DOOR)
WARNING
The trunk swings upward. Make
sure no objects or people are near
the rear of the vehicle when opening the trunk.
CAUTION
ORB043007N
ORB040006
With the key
To open the trunk, insert the key and turn
it clockwise.
With the trunk lid release lever
To open the trunk from inside the vehicle,
pull up the trunk lid release lever.
Once the trunk is opened and then
closed, the trunk is locked automatically.
Opening the trunk
✽ NOTICE
In cold and wet climates, trunk locks
and trunk mechanisms may not work
properly due to freezing conditions.
4 12
I
nf
or
mat
i
onPr
ovi
dedby:
Make certain that you close the
trunk before driving your vehicle.
Possible damage may occur to the
trunk lift cylinders and attached
hardware if the trunk is not closed
prior to driving.
Features of your vehicle
Closing the trunk
WARNING
To close the trunk, lower the trunk lid,
then press down on it until it locks. To be
sure the trunk lid is securely fastened,
always check by trying to pull it up again.
WARNING
The trunk lid should be always kept
completely closed while the vehicle
is in motion. If it is left open or ajar,
poisonous exhaust gases may
enter the vehicle and serious illness or death may result.
ORB040302
Emergency trunk safety release
Your vehicle is equipped with an emergency trunk release lever located inside
the trunk. The lever glows in the dark
when the trunk lid is closed. If someone
is inadvertently locked in the trunk,
pulling this handle will open the trunk.
I
nf
or
mat
i
onPr
ovi
dedby:
• For emergencies, be fully aware
of the location of the emergency
trunk safety release lever in this
vehicle and how to open the
trunk if you are accidentally
locked in the trunk.
• No one should be allowed to
occupy the trunk of the vehicle at
any time. If the trunk is partially
or totally latched and the person
is unable to get out, severe injury
or death could occur due to lack
of ventilation, exhaust fumes and
rapid heat build-up, or because of
exposure to cold weather conditions. The trunk is also a highly
dangerous location in the event
of a crash because it is not a protected occupant space but is a
part of the vehicle’s crush zone.
• Your vehicle should be kept
locked and keys be kept out of
the reach of children. Parents
should teach their children about
the dangers of playing in trunks.
• Use the release lever for emergencies only. Use with extreme
caution, especially while the vehicle is in motion.
4 13
Features of your vehicle
TAILGATE (5 DOOR)
✽ NOTICE
Closing the tailgate
In cold and wet climates, door lock and
door mechanisms may not work properly due to freezing conditions.
To close the tailgate, lower and push
down the tailgate firmly. Make sure that
the tailgate is securely latched.
WARNING
The tailgate swings upward. Make
sure no objects or people are near
the rear of the vehicle when opening the tailgate.
ORB041404
Opening the tailgate
• The tailgate is locked or unlocked by
turning the key to the "Lock" or
"Unlock" position.
• The tailgate is locked or unlocked
when all doors are locked or unlocked
with the key, transmitter or central door
lock switch.
• If unlocked, the tailgate can be opened
by pressing the handle and pulling it up.
4 14
WARNING
Make sure your hands, feet and other
parts of your body are safely out of
the way before closing the tailgate.
CAUTION
CAUTION
Make certain that you close the tailgate before driving your vehicle.
Possible damage may occur to the
tailgate lift cylinders and attaching
hardware if the tailgate is not
closed prior to driving.
I
nf
or
mat
i
onPr
ovi
dedby:
Make sure nothing is near the tailgate latch and striker while closing
the tailgate. It may damage the tailgate's latch.
Features of your vehicle
WARNING - Exhaust
fumes
If you drive with the tailgate open,
you will draw dangerous exhaust
fumes into your vehicle which can
cause serious injury or death to
vehicle occupants.
If you must drive with the tailgate
open, keep the air vents and all windows open so that additional outside air comes into the vehicle.
WARNING - Rear cargo
area
Occupants should never ride in the
rear cargo area where no restraints
are available. To avoid injury in the
event of an accident or sudden
stops, occupants should always be
properly restrained.
I
nf
or
mat
i
onPr
ovi
dedby:
4 15
Features of your vehicle
WINDOWS
(1) Driver’s door power window switch
(2) Front passenger’s door power window switch
(3) Rear door (left) power window switch
(4) Rear door (right) power window
switch
(5) Window opening and closing
(6) Automatic power window up/down*
(Driver’s window)
(7) Power window lock switch
* : if equipped
✽ NOTICE
In cold and wet climates, power windows
may not work properly due to freezing
conditions.
ORB043008L
4 16
I
nf
or
mat
i
onPr
ovi
dedby:
Features of your vehicle
Power windows
✽ NOTICE
• The ignition switch must be in the ON
position for power windows to operate.
Each door has a power window switch
that controls that door's window. The
driver has a power window lock switch
which can block the operation of passenger windows. The driver’s door has
a master power window switch that
controls all the windows in the vehicle.
• The power windows can be operated for
approximately 30 seconds after the ignition key is removed or turned to the ACC
or LOCK position. However, if the front
doors open, the power windows cannot
be operated within the 30 second period
(if equipped : remote keyless entry system).
While driving with the rear windows
down or with the sunroof (if equipped) in
an open (or partially open) position, your
vehicle may demonstrate a wind buffeting or pulsation noise. This noise is a
normal occurrence and can be reduced
or eliminated by taking the following
actions. If the noise occurs with one or
both of the rear windows down, partially
lower both front windows approximately one inch. If you experience the noise
with the sunroof open, slightly reduce the
size of the sunroof opening.
I
nf
or
mat
i
onPr
ovi
dedby:
ORB043092
Window opening and closing
To open or close a window, press down
or pull up the front portion of the corresponding switch to the first detent position (5).
4 17
Features of your vehicle
If the power window is not operated correctly, the automatic power window system must be reset as follows:
1. Turn the ignition switch to the ON position.
2. Close the window and continue pulling
up on the driver’s power window switch
for at least 1 second after the window
is completely closed.
ORB043093L
ORB043303L
Auto down window (if equipped)
(Driver’s window)
Pressing the power window switch
momentarily to the second detent position (6) completely lowers the driver’s
window even when the switch is
released. To stop the window at the
desired position while the window is in
operation, momentarily pull the switch in
the direction opposite of the window
movement.
Auto up/down window (if equipped)
(Driver's window)
Depressing or pulling up the power window switch momentarily to the second
detent position (6) completely lowers or
lifts the window even when the switch is
released. To stop the window at the
desired position while the window is in
operation, pull up or depress and release
the switch to the opposite direction of the
movement.
4 18
I
nf
or
mat
i
onPr
ovi
dedby:
Features of your vehicle
✽ NOTICE
The automatic reverse feature for the
driver’s window is only active when the
“auto up” feature is used by fully
pulling up the switch. The automatic
reverse feature will not operate if the
window is raised using the halfway position on the power window switch.
WARNING
OUN026013
Automatic reversal
If the upward movement of the window is
blocked by an object or part of the body,
the window will detect the resistance and
will stop upward movement. The window
will then lower approximately 30 cm (11.8
in.) to allow the object to be cleared.
If the window detects the resistance
while the power window switch is pulled
up continuously, the window will stop
upward movement then lower approximately 2.5 cm (1 in.). And if the power
window switch is pulled up continuously
again within 5 seconds after the window
is lowered by the automatic window
reversal feature, the automatic window
reversal will not operate.
Always check for obstructions
before raising any window to avoid
injuries or vehicle damage. If an
object less than 4 mm (0.16 in.) in
diameter is caught between the
window glass and the upper window channel, the automatic reverse
window may not detect the resistance and will not stop and reverse
direction.
I
nf
or
mat
i
onPr
ovi
dedby:
ORB043009L
Power window lock button
The driver can disable the power window
switches on the front and rear passengers' doors by pressing the power window
lock switch to lock position (pressed).
When the power window lock switch is
pressed, the driver's master control cannot operate the front and rear passengers' power windows.
4 19
Features of your vehicle
CAUTION
• To prevent possible damage to
the power window system, do not
open or close two windows or
more at the same time. This will
also ensure the longevity of the
fuse.
• Never try to operate the main
switch on the driver's door and
the individual door window
switch in opposing directions at
the same time. If this is done, the
window will stop and cannot be
opened or closed.
4 20
.
WARNING - Windows
• NEVER leave the keys in your
vehicle with unsupervised children, when the Engine is running.
• NEVER leave any child unattended in the vehicle. Even very
young children may inadvertently
cause the vehicle to move, entangle themselves in the windows,
or otherwise injure themselves or
others.
• Always double check to make
sure all arms, hands, head and
other obstructions are safely out
of the way before closing a window.
• Do not allow children to play with
the power windows. Keep the driver’s door power window lock
switch in the LOCK position
(depressed). Serious injury can
result from unintentional window
operation by the child.
• Do not extend any head or arms
outside through the window opening while driving.
I
nf
or
mat
i
onPr
ovi
dedby:
Features of your vehicle
HOOD
ORB040011
ORBC044012
2. Go to the front of the vehicle, raise the
hood slightly, push the secondary latch
(1) to the left and lift the hood (2).
3. Pull out the support rod from the
engine room (3).
4. Hold the hood open with the support
rod (4).
ORB040010
Opening the hood
1. Pull the release lever to unlatch the
hood. The hood should pop open
slightly.
WARNING - Hot parts
WARNING
Grasp the support rod in the area
wrapped in rubber. The rubber will
help prevent you from being burned
by hot metal when the engine is
hot.
Open the hood after turning off the
engine on a flat surface, shifting
the shift lever to the P(Park) position for automatic transaxle and to
the 1st(First) gear or R(Reverse) for
manual transaxle, and setting the
parking brake.
I
nf
or
mat
i
onPr
ovi
dedby:
4 21
Features of your vehicle
Closing the hood
1. Before closing the hood, check the following:
• All filler caps in engine compartment
must be correctly installed.
• Gloves, rags or any other combustible material must be removed
from the engine compartment.
2. Return the support rod to its clip to
prevent it from rattling.
3. Lower the hood until it is about 1 ft. (30
cm) above the closed position and let
it drop. Make sure that it locks into
place.
4 22
WARNING
• Before closing the hood, ensure
that all obstructions are removed
from the hood opening. Closing
the hood with an obstruction
present in the hood opening may
result in property damage or
severe personal injury.
• Do not leave gloves, rags or any
other combustible material in the
engine compartment. Doing so
may cause a heat-induced fire.
• Always double check to be sure
that the hood is firmly latched
before driving away. If it is not
latched, the hood could open
while the vehicle is being driven,
causing a total loss of visibility,
which might result in an accident.
• Do not move the vehicle with the
hood in the raised position, as
vision is obstructed and the hood
could fall or be damaged.
I
nf
or
mat
i
onPr
ovi
dedby:
Features of your vehicle
FUEL FILLER LID
Closing the fuel filler lid
1. To install the cap, turn it clockwise until
it clicks one time. This indicates that
the cap is securely tightened.
2. Close the fuel filler lid and push it in
lightly making sure that it is securely
closed.
WARNING - Refueling
ORB040013
Opening the fuel filler lid
The fuel filler lid must be opened from
inside the vehicle by pulling the fuel filler
lid opener switch.
✽ NOTICE
If the fuel filler lid will not open because
ice has formed around it, tap lightly or
push on the lid to break the ice and
release the lid. Do not pry on the lid. If
necessary, spray around the lid with an
approved de-icer fluid (do not use radiator anti-freeze) or move the vehicle to a
warm place and allow the ice to melt.
ORB044014A
1. Stop the engine.
2. To open the fuel filler lid, pull the fuel
filler lid opener switch.
3. Pull the fuel filler lid (1) out to fully
open.
4. To remove the cap, turn the fuel tank
cap (2) counterclockwise.
5. Refuel as needed.
I
nf
or
mat
i
onPr
ovi
dedby:
• If pressurized fuel sprays out, it
can cover your clothes or skin
and thus subject you to the risk
of fire and burns. Always remove
the fuel cap carefully and slowly.
If the cap is venting fuel or if you
hear a hissing sound, wait until
the condition stops before completely removing the cap.
• Do not "top off" after the nozzle
automatically shuts off when
refueling.
• Tighten the cap until it clicks one
time, otherwise the fuel cap open
warning light
will illuminate.
• Always check that the fuel cap is
installed securely to prevent fuel
spillage in the event of an accident.
4 23
Features of your vehicle
WARNING - Refueling dangers
Automotive fuels are flammable
materials. When refueling, please
note the following guidelines carefully. Failure to follow these guidelines may result in severe personal
injury, severe burns or death by fire
or explosion.
• Read and follow all warnings
posted at the gas station facility.
• Before refueling, note the location of the Emergency Gasoline
Shut-Off, if available, at the gas
station facility.
• Before touching the fuel nozzle,
you should eliminate potentially
dangerous static electricity discharge by touching another metal
part of the vehicle, a safe distance away from the fuel filler
neck, nozzle, or other gas source.
(Continued)
4 24
(Continued)
• Do not get back into a vehicle
once you have begun refueling
since you can generate static
electricity by touching, rubbing
or sliding against any item or fabric (polyester, satin, nylon, etc.)
capable of producing static electricity. Static electricity discharge
can ignite fuel vapors resulting in
rapid burning. If you must reenter the vehicle, you should
once again eliminate potentially
dangerous static electricity discharge by touching a metal part
of the vehicle, away from the fuel
filler neck, nozzle or other gasoline source.
• When
using
an
approved
portable fuel container, be sure to
place the container on the
ground prior to refueling. Static
electricity discharge from the
container can ignite fuel vapors
causing a fire. Once refueling has
begun, contact with the vehicle
should be maintained until the
filling is complete.
(Continued)
I
nf
or
mat
i
onPr
ovi
dedby:
(Continued)
Use only approved portable plastic fuel containers designed to
carry and store gasoline.
• Do not use cellular phones while
refueling. Electric current and/or
electronic interference from cellular phones can potentially
ignite fuel vapors causing a fire.
• When refueling, always shut the
engine off. Sparks produced by
electrical components related to
the engine can ignite fuel vapors
causing a fire. Once refueling is
complete, check to make sure the
filler cap and filler door are
securely closed, before starting
the engine.
• DO NOT use matches or a lighter
and DO NOT SMOKE or leave a lit
cigarette in your vehicle while at
a gas station especially during
refueling. Automotive fuel is
highly flammable and can, when
ignited, result in fire.
(Continued)
Features of your vehicle
(Continued)
• If a fire breaks out during refueling, leave the vicinity of the vehicle, and immediately contact the
manager of the gas station and
then contact the local fire department or 911. Follow any safety
instructions they provide.
CAUTION
• Make sure to refuel your vehicle
according to the "Fuel requirements" suggested in section 1.
• If the fuel filler cap requires
replacement, use only a genuine
HYUNDAI cap or the equivalent
specified for your vehicle. An
incorrect fuel filler cap can result
in a serious malfunction of the
fuel system or emission control
system.
• Do not spill fuel on the exterior
surfaces of the vehicle. Any type
of fuel spilled on painted surfaces
may damage the paint.
• After refueling, make sure the fuel
cap is installed securely to prevent fuel spillage in the event of
an accident.
I
nf
or
mat
i
onPr
ovi
dedby:
4 25
Features of your vehicle
SUNROOF (IF EQUIPPED)
✽ NOTICE
✽ NOTICE
• In cold and wet climates, the sunroof
may not work properly due to freezing conditions.
• After washing the car or after there is
rain, be sure to wipe off any water that
is on the sunroof before operating it.
The sunroof cannot slide when it is in
the tilt position nor can it be tilted while
in an open or slide position.
CAUTION
ORB040015
If your vehicle is equipped with a sunroof,
you can slide or tilt your sunroof with the
sunroof control switch located on the
overhead console.
Do not continue to move the sunroof control lever after the sunroof
is in the fully open, closed, or tilt
position. Damage to the motor or
system components could occur.
The sunroof can only be opened, closed,
or tilted when the ignition switch is in the
ON position.
4 26
I
nf
or
mat
i
onPr
ovi
dedby:
WARNING
Never adjust the sunroof or sunshade while driving. This could
result in loss of control and an accident that may cause death, serious
injury, or property damage.
Features of your vehicle
To open the sunroof to the maximum
slide open position, press the the switch
towards the rear of the vehicle once
again and hold it until the sunroof slides
all the way open.
✽ NOTICE
To reduce wind noise while driving, we
recommend you to drive at the recommended postion (about 2 in. before the
maximum slide open positon).
ORB040016
Sliding the sunroof
To open or close the sunroof (manual
slide feature), pull or push the sunroof
control lever backward or forward to the
first detent position.
To open the sunroof (autoslide feature),
press the sunroof control switch towards
the rear of the vehicle for more than 0.5
second.
The sunroof will slide to the recommended open position (about 2 in. before the
maximum slide open position).
To stop the sunroof sliding at any point,
pull or push the sunroof control switch
momentarily.
To close the sunroof (autoslide feature),
move the sunroof control switch towards
the front of the vehicle for more than 0.5
second.
The sunroof will close all the way. To stop
the sunroof sliding at any point, pull or
push the sunroof control switch momentarily.
I
nf
or
mat
i
onPr
ovi
dedby:
OBK049018
Automatic reversal
If an object or part of the body is detected while the sunroof is closing automatically, it will reverse direction, and then
stop.
The auto reverse function does not work
if a small obstacle is between the sliding
glass and the sunroof sash. You should
always check that all passengers and
objects are away from the sunroof before
closing it.
4 27
Features of your vehicle
WARNING - Sunroof
• Be careful that someone’s head,
hands and body are not trapped
by a closing sunroof.
• Do not extend face, neck, arms or
body outside through the sunroof
opening while driving.
• Make sure hand and face are
safely out of the way before closing a sunroof.
ORB040017
Tilting the sunroof
To open the sunroof
Push the sunroof control lever upward
until the sunroof moves to the desired
position.
To close the sunroof
Pull the sunroof lever downward until the
sunroof moves to the desired position.
4 28
I
nf
or
mat
i
onPr
ovi
dedby:
CAUTION
• Periodically remove any dirt that
may accumulate on the guide rail.
• If you try to open the sunroof when
the temperature is below freezing
or when the sunroof is covered
with snow or ice, the glass or the
motor could be damaged.
• While using sunroof for a long
time, a dust between sunroof and
roof panel can make a noise. Open
the sunroof and regularly remove
the dust using clean cloth.
Features of your vehicle
Resetting the sunroof
Whenever the vehicle battery is disconnected or discharged, or related fuse is
blown, you must reset your sunroof system as follows:
OBK049019
Sunshade
The sunshade will be opened with the
glass panel automatically when the glass
panel is opened. You will have to close it
manually if you want it closed.
CAUTION
The sunroof is made to slide
together with the sunshade. Do not
leave the sunshade closed while
the sunroof is open.
1. Turn the ignition switch to the ON position and close the sunroof completely.
2. Release the control lever.
3. Push and hold the control lever forward (for more than 10 seconds) until
the sunroof tilts and slightly moves.
Then, release the lever.
4. Within 3 seconds, push and hold the
control lever forward (for more than 5
seconds) until the sunroof is operated
as follows;
❈ For more detailed information, contact
an authorized HYUNDAI dealer.
CAUTION
If the sunroof is not reset when the
vehicle battery is disconnected or
discharged, or related fuse is blown,
the sunroof may operate improperly.
TILT DOWN → SLIDE OPEN →
SLIDE CLOSE
Then, release the control lever.
When this is complete, the sunroof system is reset.
I
nf
or
mat
i
onPr
ovi
dedby:
4 29
Features of your vehicle
STEERING WHEEL
Electric power steering (EPS)
The power steering uses a motor to
assist you in steering the vehicle. If the
engine is off or if the power steering system becomes inoperative, the vehicle
may still be steered, but it will require
increased steering effort.
The motor driven power steering is controlled by a power steering control unit
which senses the steering wheel torque
and vehicle speed to command the
motor.
The steering becomes heavier as the
vehicle’s speed increases and becomes
lighter as the vehicle’s speed decreases
for optimum steering control.
Should you notice any change in the
effort required to steer during normal
vehicle operation, have the power steering checked by an authorized HYUNDAI
dealer.
4 30
CAUTION
• If the Electric Power Steering
System does not operate normally, the warning light will illuminate
on the instrument cluster. The
steering wheel may become difficult to control or operate abnormally. Take your vehicle to an
authorized HYUNDAI dealer and
have the vehicle checked as soon
as possible.
• When you operate the steering
wheel in low temperature, abnormal noise could occur. If temperature rises, the noise will disappear. This is a normal condition.
• When the vehicle is stationary, if
you turn the steering wheel all the
way to the left or right continuously, the
steering
wheel
becomes heavier from the end.
But this is for your safety, not system malfunction. As time passes,
the steering wheel will return to
its normal condition.
I
nf
or
mat
i
onPr
ovi
dedby:
✽ NOTICE
The following symptoms may occur during normal vehicle operation:
• The EPS warning light does not illuminate.
• The steering gets heavy immediately
after turning the ignition switch on.
This happens as the system performs
the EPS system diagnostics. When the
diagnostics is completed, the steering
wheel will return to its normal condition.
• A click noise may be heard from the
EPS relay after the ignition switch is
turned to the ON or LOCK (OFF)
position.
• A motor noise may be heard when the
vehicle is at a stop or at a low driving
speed.
• If the Electric Power Steering System
does not operate normally, the warning
light will illuminate on the instrument
cluster. The steering wheel may
become difficult to control or operate
abnormally. Take your vehicle to an
authorized HYUNDAI dealer and have
the vehicle checked as soon as possible.
• When you operate the steering wheel in
low temperature, abnormal noise could
occur. If temperature rises, the noise will
disappear. This is a normal condition.
(Continued)
Features of your vehicle
(Continued)
• When the charging system warning
light comes on or the voltage is low
(When the alternator (or battery) does
not operate normally or it malfunctions), the steering wheel may get
heavy and become difficult to control
operate abnormally.
Tilt and telescopic steering
(if equipped)
Tilt and telescopic steering allows you to
adjust the steering wheel before you
drive. You can also raise it to give your
legs more room when you exit and enter
the vehicle.
The steering wheel should be positioned
so that it is comfortable for you to drive,
while permitting you to see the instrument panel warning lights and gauges.
WARNING
• Never adjust the angle of the
steering wheel while driving. You
may lose steering control and
cause severe personal injury,
death or accidents.
• After adjusting, push the steering
wheel both up and down to be
certain it is locked in position.
I
nf
or
mat
i
onPr
ovi
dedby:
ORB044018N
To change the steering wheel angle and
height, pull down the lock release lever
(1), adjust the steering wheel to the
desired angle (2) and height (3), then pull
up the lock-release lever to lock the
steering wheel in place. Be sure to adjust
the steering wheel to the desired position
before driving.
4 31
Features of your vehicle
MIRRORS
Inside rearview mirror
Adjust the rearview mirror so that the
center view through the rear window is
seen. Make this adjustment before you
start driving.
Night
WARNING - Rear visibility
Do not place objects in the rear
seat or cargo area which would
interfere with your vision through
the rear window.
ORBC040019
ORB040020
Horn
To sound the horn, press the horn symbol on your steering wheel.
Check the horn regularly to be sure it
operates properly.
✽ NOTICE
WARNING
Do not modify the inside mirror and
do not install a wide mirror. It could
result in injury, during an accident
or deployment of the air bag.
To sound the horn, press the area indicated by the horn symbol on your steering wheel (see illustration). The horn will
operate only when this area is pressed.
CAUTION
Do not strike the horn severely to
operate it, or hit it with your fist. Do
not press on the horn with a sharppointed object.
4 32
Day
I
nf
or
mat
i
onPr
ovi
dedby:
Day/night rearview mirror
Make this adjustment before you start
driving and while the day/night lever is in
the day position.
Pull the day/night lever toward you to
reduce glare from the headlights of the
vehicles behind you during night driving.
Remember that you lose some rearview
clarity in the night position.
Features of your vehicle
Outside rearview mirror
Be sure to adjust mirror angles before
driving.
Your vehicle is equipped with both lefthand and right-hand outside rearview
mirrors. The mirrors can be adjusted
remotely with the remote switch. The mirror heads can be folded back to prevent
damage during an automatic car wash or
when passing in a narrow street.
CAUTION
Do not scrape ice off the mirror
face; this may damage the surface
of the glass. If ice should restrict
movement of the mirror, do not
force the mirror for adjustment. To
remove ice, use a deicer spray, or a
sponge or soft cloth with warm
water.
ORB044380N
WARNING - Rearview mirrors
• The right outside rearview mirror
is convex. Objects seen in the
mirror are closer than they
appear.
• Use your interior rearview mirror
or direct observation to determine the actual distance of following vehicles when changing
lanes.
CAUTION
If the mirror is jammed with ice, do
not adjust the mirror by force. Use
an approved spray de-icer (not radiator antifreeze) to release the
frozen mechanism or move the
vehicle to a warm place and allow
the ice to melt.
OFS053068
WARNING
Do not adjust or fold the outside
rearview mirrors while the vehicle
is moving. This could result in loss
of control, and an accident which
could cause death, serious injury
or property damage.
I
nf
or
mat
i
onPr
ovi
dedby:
Blind zone mirror (if equipped)
The blind zone mirror (BZM) is supplemental mirror to reduce a driver's blind
zone that will show the rear side territory
of your vehicle. The blind zone mirror is
equipped with the left-hand outside
rearview mirror.
4 33
Features of your vehicle
CAUTION
WARNING
• The mirrors stop moving when
they reach the maximum adjusting angles, but the motor continues to operate while the switch is
pressed. Do not press the switch
longer than necessary, the motor
may be damaged.
• Do not attempt to adjust the outside rearview mirror by hand.
Doing so may damage the mirror.
• Always check the road condition
while driving for unexpected situations even though the vehicle is
equipped with a blind zone mirror.
• The blind zone mirror is a device
made for convenience. Do not
solely rely on the mirror but
always pay attention to drive
safely.
ORBC040023
Remote control
Electric type
The electric remote control mirror switch
allows you to adjust the position of the
left and right outside rearview mirrors. To
adjust the position of either mirror, the
ignition switch should be in the ACC or
ON position, or engine is running. Push
the switch (1) to R or L to select the right
side mirror or the left side mirror, then
press a corresponding point on the mirror
adjustment control to position the selected mirror up, down, left or right.
After the adjustment, put the switch into
the neutral (center) position to prevent
inadvertent adjustment.
4 34
I
nf
or
mat
i
onPr
ovi
dedby:
Features of your vehicle
ORB040024
Folding the outside rearview mirror
(if equipped)
To fold outside rearview mirror, grasp the
housing of mirror and then fold it toward
the rear of the vehicle.
I
nf
or
mat
i
onPr
ovi
dedby:
4 35
Features of your vehicle
INSTRUMENT CLUSTER
■ Type A
1. Tachometer
2. Turn signal indicators
3. Speedometer
4. Engine temperature gauge
5. Warning and indicator lights
6. Fuel gauge
7. Odometer/Trip computer
■ Type B
❈ The actual cluster in the vehicle may
differ from the illustration.
For more details refer to the "Gauges"
section in the next pages.
ORB044025N/ORB044026N
4 36
I
nf
or
mat
i
onPr
ovi
dedby:
Features of your vehicle
■ Type A
■ Type A
ORB040031N
ORB040332
■ Type B
ORB040305
■ Type B
Instrument panel illumination
When the vehicle’s parking lights or
headlights are on, press the upper or
lower part of the switch to adjust the
brightness of the instrument panel illumination.
ORB040030N
Gauges
Speedometer
The speedometer indicates the speed of
the vehicle.
The speedometer is calibrated in miles
per hour and/or kilometers per hour.
I
nf
or
mat
i
onPr
ovi
dedby:
ORB040306
Tachometer
The tachometer indicates the approximate number of engine revolutions per
minute (rpm).
Use the tachometer to select the correct
shift points and to prevent lugging and/or
over-revving the engine.
4 37
Features of your vehicle
When the door is open, or if the engine is
not started within 1 minute, the tachometer
pointer may move slightly in ON position
with the engine OFF. This movement is
normal and will not affect the accuracy of
the tachometer once the engine is running.
■ Type A
■ Type B
WARNING
Never remove the radiator cap
when the engine is hot. The engine
coolant is under pressure and
could cause severe burns. Wait
until the engine is cool before
adding coolant to the reservoir.
CAUTION
Do not operate the engine within
the tachometer's RED ZONE.
This may cause severe engine damage.
ORB040308N
Engine temperature gauge
This gauge shows the temperature of the
engine coolant when the ignition switch
is ON.
Do not continue driving with an overheated engine. If your vehicle overheats, refer
to “If the engine overheats” in section 6.
CAUTION
If the gauge moves beyond the normal range area toward the “H” position, it indicates overheating that
may damage the engine.
4 38
I
nf
or
mat
i
onPr
ovi
dedby:
Features of your vehicle
■ Type A
■ Type B
WARNING - Fuel gauge
Running out of fuel can expose
vehicle occupants to danger.
You must stop and obtain additional fuel as soon as possible after the
warning light comes on or when the
gauge indicator comes close to the
E level.
ORB040034N
Fuel gauge
The fuel gauge indicates the approximate amount of fuel remaining in the fuel
tank. The fuel tank capacity is given in
section 8. The fuel gauge is supplemented by a low fuel warning light, which will
illuminate when the fuel tank is near
empty.
On inclines or curves, the fuel gauge
may fluctuate or the low fuel warning light
may come on earlier than usual due to
the movement of fuel in the tank.
CAUTION
Avoid driving with an extremely low
fuel level. Running out of fuel could
cause the engine to misfire, damaging the catalytic converter.
I
nf
or
mat
i
onPr
ovi
dedby:
ORBC040035
Trip computer
The trip computer is a microcomputer
controlling the driver information system.
It displays information related to driving
on the LCD screen when the ignition
switch is in the ON position. If the battery
is disconnected, then all stored driving
information (except odometer) is reset.
4 39
Features of your vehicle
TRIP A
■ Type A
■ Type B
■ Type A
■ Type B
TRIP B
Distance to empty
Average fuel consumption
Instant fuel consumption
Average speed
Elapsed time
ORB044036N
ORB040037N
Odometer (mi. or km)
The odometer indicates the total distance the vehicle has been driven.
You will also find the odometer useful to
determine when periodic maintenance
should be performed.
Tripmeter (mi. or km)
TRIP A : Tripmeter A
TRIP B : Tripmeter B
This mode indicates the distance of individual trips selected since the last tripmeter reset.
The meter's working range is from 0.0 to
9999.9 miles (0.0 to 9999.9 km).
Pressing the RESET button for more
than 1 second, when the tripmeter (TRIP
A or TRIP B) is being displayed, clears
the tripmeter to zero (0.0).
Outside temperature*
* : if equipped
4 40
I
nf
or
mat
i
onPr
ovi
dedby:
Features of your vehicle
■ Type A
■ Type B
■ Type A
■ Type B
■ Type A
■ Type B
ORB040038N
ORB044039N
ORB040040N
Distance to empty (mi. or km)
This mode indicates the estimated distance to empty based on the current fuel
in the fuel tank and the amount of fuel
delivered to the engine. When the
remaining distance is below 30 miles (50
km), “---” will be displayed and the distance to empty indicator will blink.
The meter’s working range is from 30 to
999 miles (50 to 999 km).
Average fuel consumption (if equipped)
(MPG or l/100 km)
This mode calculates the average fuel
consumption from the total fuel used and
the distance since the last average economy reset. The total fuel used is calculated from the fuel consumption input. For
an accurate calculation, drive more than
0.03 miles (50 m).
Pressing the RESET button for more than
1 second, when the average fuel economy is being displayed, clears the average
fuel consumption to zero (----).
If the vehicle speed exceeds 1.6 MPH
(1km/h) after being refueling, the average
fuel economy will be cleared to zero (----).
Instant fuel consumption
(MPG or l/100 km)
This mode calculates the instant fuel
consumption every 2 seconds from the
driving distance and quantity of fuel
injection.
I
nf
or
mat
i
onPr
ovi
dedby:
4 41
Features of your vehicle
■ Type A
■ Type A
■ Type B
■ Type A
■ Type B
■ Type B
ORB044041N
ORB040042N
ORB040309N
Average speed (MPH or km/h)
This mode calculates the average speed
of the vehicle since the last average
speed reset.
Even if the vehicle is not in motion, the
average speed keeps changing while the
engine is running.
Pressing the RESET button for more
than 1 second, when the average speed
is being displayed, clears the average
speed to zero (---).
Elapsed time
This mode indicates the total time traveled since the last driving time reset.
Even if the vehicle is not in motion, the
driving time keeps increasing while the
engine is running.
The meter’s working range is from
00:00~99:59.
Pressing the RESET button for more
than 1 second, when the driving time is
being displayed, clears the driving time to
zero (00:00).
Outside thermometer (if equipped)
The current outside temperature is displayed in 1°C (1°F) increments. The temperature range is between -40°C ~ 60°C
(-40°F ~ 140°F).
• The outside temperature on the display
may not change immediately like a
general thermometer to prevent the
driver from being inattentive.
4 42
I
nf
or
mat
i
onPr
ovi
dedby:
Features of your vehicle
Warnings and indicators
All warning lights are checked by turning
the ignition switch ON (do not start the
engine). Any light that does not illuminate
should be checked by an authorized
HYUNDAI dealer.
After starting the engine, check to make
sure that all warning lights are off. If any
are still on, this indicates a situation that
needs attention. When releasing the
parking brake, the brake system warning
light should go off. The fuel warning light
will stay on if the fuel level is low.
ECO indicator
Air bag warning light
ECO
Active ECO system
When the active ECO is operating the
ECO indicator is green.
For more detailed information, refer to
“Active ECO” in chapter 5.
WARNING
Don't keep watching the indicator
while driving. It will distract you
while driving and cause an accident
that results in severe personal injury.
I
nf
or
mat
i
onPr
ovi
dedby:
This warning light will illuminate for
approximately 6 seconds each time you
turn the ignition switch to the ON position.
This light also comes on when the
Supplemental Restraint System (SRS) is
not working properly. If the SRS air bag
warning light
does not come on, or
continuously remains on after operating
for about 6 seconds when you turned the
ignition switch to the ON position or started the engine, or if it comes on while
driving, have the SRS inspected by an
authorized HYUNDAI dealer.
4 43
Features of your vehicle
Anti-lock brake system
(ABS) warning light
This light illuminates if the ignition switch
is turned ON and goes off in approximately 3 seconds if the system is operating normally.
If the ABS warning light remains on,
comes on while driving, or does not
come on when the ignition switch is
turned to the ON position, this indicates
that there may be a malfunction with the
ABS.
If this occurs, have your vehicle checked
by an authorized HYUNDAI dealer as
soon as possible. The normal braking
system will still be operational, but without the assistance of the anti-lock brake
system.
4 44
If the ABS warning light turns on while
driving
1. Park the vehicle in a safe place and
turn off the engine.
2. Turn on the engine again.
3. If the warning light illuminates and
turns off in approximately 3 seconds,
the system is operating normally.
If the warning light does not turn off, have
your vehicle checked by an authorized
HYUNDAI dealer as soon as possible.
Electronic brake force distribution (EBD) system warning
light
If these two warning lights illuminate at
the same time while driving, your vehicle
may have a malfunction with the ABS
and EBD system.
In this case, your ABS and regular brake
system may not work normally. Have the
vehicle checked by an authorized
HYUNDAI dealer as soon as possible.
WARNING
If the both ABS and brake warning
lights are on and stay on, your vehicle’s brake system will not work
normally during sudden braking. In
this case, avoid high speed driving
and abrupt braking. Have your vehicle checked by an authorized
HYUNDAI dealer as soon as possible.
I
nf
or
mat
i
onPr
ovi
dedby:
Features of your vehicle
✽ NOTICE
If the ABS warning light or EBD warning light is on and stays on, the
speedometer or odometer/tripmeter
may not work. In this case, have your
vehicle checked by an authorized
HYUNDAI dealer as soon as possible.
Seat belt warning
The driver's seat belt warning light and
chime will activate to the following table
when the ignition switch is in "ON" position.
Conditions
Seat Belt
Vehicle
Speed
Unbuckled
Unbuckled
Turn signal indicator
ChimeSound
Light-Blink
6 seconds
Buckled
Buckled →
Unbuckled
Warning Pattern
6 seconds
None
Below 3 mph
6 seconds
(5 km/h)
None
3 mph~
6 mph
6 seconds
Above 6 mph
(10 km/h)
6 sec. on / 24 sec. off
(11 times)
Above 6 mph
(10 km/h)
6 seconds *1
↓
↓
Below 3 mph
(5 km/h)
Stop *2
*1 Warning pattern repeats 11 times with
interval 24 seconds. If the driver's seat
belt is buckled, the light will stop within
6 seconds and chime will stop immediately.
*2 The light will stop within 6 seconds and
chime will stop immediately.
The blinking arrows on the instrument
panel show the direction indicated by the
turn signals. If the arrow comes on but
does not blink, blinks more rapidly than
normal, or does not illuminate at all, a
malfunction in the turn signal system is
indicated. Your dealer should be consulted for repairs.
High beam indicator
This indicator illuminates when the headlights are on and in the high beam position or when the turn signal lever is pulled
into the Flash-to-Pass position.
Tail light indicator
This indicator illuminates when the tail
lights are on.
I
nf
or
mat
i
onPr
ovi
dedby:
4 45
Features of your vehicle
Engine oil pressure
warning light
This warning light indicates the engine oil
pressure is low.
If the warning light illuminates while driving:
1. Drive safely to the side of the road and
stop.
2. With the engine off, check the engine
oil level. If the level is low, add oil as
required.
If the warning light remains on after
adding oil or if oil is not available, call an
authorized HYUNDAI dealer.
CAUTION
If the engine is not stopped immediately after the engine oil pressure
warning light is illuminated, severe
damage could result.
4 46
CAUTION
If the oil pressure warning light
stays on while the engine is running, serious engine damage may
result. The oil pressure warning
light comes on whenever there is
insufficient oil pressure. In normal
operation, it should come on when
the ignition switch is turned on,
then go out when the engine is
started. If the oil pressure warning
light stays on while the engine is
running, there is a serious malfunction.
If this happens, stop the car as
soon as it is safe to do so, turn off
the engine and check the oil level. If
the oil level is low, fill the engine oil
to the proper level and start the
engine again. If the light stays on
with the engine running, turn the
engine off immediately. In any
instance where the oil light stays on
when the engine is running, the
engine should be checked by an
authorized HYUNDAI dealer before
the car is driven again.
I
nf
or
mat
i
onPr
ovi
dedby:
Parking brake & brake fluid
warning light
Parking brake warning
This light is illuminated when the parking
brake is applied with the ignition switch in
the START or ON position. The warning
light should go off when the parking
brake is released.
Low brake fluid level warning
If the warning light remains on, it may
indicate that the brake fluid level in the
reservoir is low.
If the warning light remains on:
1. Drive carefully to the nearest safe
location and stop your vehicle.
2. With the engine stopped, check the
brake fluid level immediately and add
fluid as required. Then check all brake
components for fluid leaks.
3. Do not drive the vehicle if leaks are
found, the warning light remains on or
the brakes do not operate properly.
Have the vehicle towed to any authorized HYUNDAI dealer for a brake system inspection and necessary repairs.
Features of your vehicle
Your vehicle is equipped with a dualdiagonal braking system. This means you
still have braking on two wheels even if
one of the brake circuits is damaged or
malfunctions. With only one of the circuits
working, more than normal pedal travel
and greater pedal pressure are required
to stop the car. Also, the car will not stop
in as short a distance with only a portion
of the brake system working. If the
brakes fail while you are driving, shift to a
lower gear for additional engine braking
and stop the car as soon as it is safe to
do so.
To check bulb operation, check whether
the parking brake and brake fluid warning
light illuminates when the ignition switch
is in the ON position.
WARNING
Driving the vehicle with a warning
light on is dangerous. If the brake
warning light remains on, have the
brakes checked and repaired immediately by an authorized HYUNDAI
dealer.
TPMS (Tire Pressure Monitoring
System) indicator (if equipped)
Low tire pressure telltale
Low tire pressure position
telltale (if equipped)
The low tire pressure telltale and low tire
position telltale illuminate when one or
more of your tires is significantly underinflated.
Inflate your tires to the correct inflation
pressure.
The low tire pressure telltale will illuminate after it blinks for approximately one
minute when there is a problem with the
Tire Pressure Monitoring System.
If this occurs, have the system checked
by an authorized HYUNDAI dealer as
soon as possible.
For details, refer to the TPMS on chapter 6.
I
nf
or
mat
i
onPr
ovi
dedby:
WARNING - Low tire pressure
Significantly low tire pressure
makes the vehicle unstable and can
contribute to loss of vehicle control
and increased braking distances.
Continued driving on tires with low
pressure will cause the tires to
overheat and fail.
WARNING - Safe stopping
• The TPMS cannot alert you to
severe and sudden tire damage
caused by external factors.
• If you feel any vehicle instability,
immediately take your foot off the
accelerator, apply the brakes
gradually and with light force,
and slowly move to a safe position off the road.
4 47
Features of your vehicle
Automatic Transaxle shift
indicator
Charging system warning
light
The indicator displays which automatic
transaxle shift position is selected.
This warning light indicates a malfunction
of either the generator or electrical
charging system.
If the warning light comes on while the
vehicle is in motion:
1. Drive to the nearest safe location.
2. With the engine off, check the generator drive belt for looseness or breakage.
3. If the belt is adjusted properly, a problem exists somewhere in the electrical
charging system. Have an authorized
HYUNDAI dealer correct the problem
as soon as possible.
Manual transaxle shift
indicator (if equipped)
This indicator informs you which gear is
desired while driving to save fuel.
For example
: Indicates that shifting up to the 3rd
gear is desired (currently the shift
lever is in the 2nd gear).
: Indicates that shifting down to the
3rd gear is desired (currently the
shift lever is in the 4th gear).
This light comes on when the front fog
lights are ON.
Trunk lid / tailgate open
warning light
This warning light illuminates when the
trunk lid / tailgate is not closed securely
with the ignition in any position.
Door open warning light
✽ NOTICE
When the charging system warning light
comes on or the voltage is low (when the
alteranator (or battery) does not operate
normally or it malfunctions), the steering wheel may get heavy and become difficult to control operate abnormally.
4 48
Front fog light indicator
(if equipped)
I
nf
or
mat
i
onPr
ovi
dedby:
This indicator illuminates when a door is
not closed securely.
Features of your vehicle
Key reminder warning chime
(if equipped)
If the driver’s door is opened while the
ignition key is left in the ignition switch
(ACC or LOCK position), the key
reminder warning chime will sound. This
helps prevent you from locking your keys
in the vehicle. The chime sounds until the
key is removed from the ignition switch or
the driver’s door is closed.
Low fuel level warning light
This warning light indicates the fuel tank
is nearly empty. When it comes on, you
should add fuel as soon as possible.
Driving with the fuel level warning light on
or with the fuel level below “E” can cause
the engine to misfire and damage the
catalytic converter.
Malfunction indicator light
(MIL) (check engine light)
This indicator light is part of the Engine
Control System which monitors various
emission control system components. If
this light illuminates while driving, it indicates that a potential malfunction has
been detected somewhere in the emission control system.
This light will also illuminate when the
ignition switch is turned to the ON position, and will go out in a few seconds
after the engine is started. If it illuminates
while driving, or does not illuminate when
the ignition switch is turned to the ON
position, take your vehicle to your nearest authorized HYUNDAI dealer and
have the system checked.
Generally, your vehicle will continue to be
drivable, but have the system checked by
an authorized HYUNDAI dealer promptly.
I
nf
or
mat
i
onPr
ovi
dedby:
CAUTION
• Prolonged driving with the
Malfunction Indicator Light illuminated may cause damage to the
emission control systems which
could effect drivability and/or fuel
economy.
• If the Malfunction Indicator Light
illuminates or blinks, potential
catalytic converter damage is
possible. This could result in loss
of engine power. Have the Engine
Control System inspected as
soon as possible by an authorized HYUNDAI dealer.
4 49
Features of your vehicle
ESC (Electronic Stability
Control) indicator
ESC OFF indicator
Cruise indicator (if equipped)
CRUISE indicator
The ESC indicator will illuminate when
the ignition switch is turned ON, but
should go off after approximately 3 seconds. When the ESC is on, it monitors
the driving conditions. Under normal driving conditions, the ESC light will remain
off. When a slippery or low traction condition is encountered, the ESC will operate, and the ESC indicator will blink to
indicate the ESC is operating.
The ESC indicator stays on when the
ESC may have a malfunction. Take your
car to an authorized HYUNDAI dealer
and have the system checked.
4 50
The ESC OFF indicator will illuminate
when the ignition switch is turned ON,
but should go off after approximately 3
seconds. To switch to ESC OFF mode,
press the ESC OFF button. The ESC
OFF indicator will illuminate indicating
the ESC is deactivated.
I
nf
or
mat
i
onPr
ovi
dedby:
CRUISE
The indicator light illuminates when the
cruise control system is enabled.
The cruise indicator light in the instrument cluster is illuminated when the
cruise control ON-OFF button on the
steering wheel is pushed.
The indicator light turns off when the
cruise control ON-OFF button is pushed
again. For more information about the
use of cruise control, refer to “Cruise
control system” in section 5.
Features of your vehicle
Cruise SET indicator
SET
The indicator light illuminates when the
cruise function switch (SET- or RES+) is
ON.
The cruise SET indicator light in the
instrument cluster is illuminated when
the cruise control switch (SET- or RES+)
is pushed. The cruise SET indicator light
does not illuminate when the cruise control switch (CANCEL) is pushed or the
system is disengaged.
Electric power steering
(EPS) system warning light
Engine coolant temperature warning light
This indicator light comes on after the
ignition key is turned to the ON position
and then it will go out.
This light also comes on when the EPS
needs repairs. If it comes on while driving, have your vehicle inspected by an
authorized HYUNDAI dealer.
Steering effort may increase significantly
if this lamp illuminates. See EPS system
in this section.
The warning light illuminates if the temperature of the engine coolant is above
257±4.5°F (125±2.5°C).
Do not continue driving with an overheated engine. If your vehicle overheats, refer
to “Overheating” in section 6.
✽ NOTICE
If the engine coolant temperature warning light illuminates, it indicates overheating that may damage the engine.
Fuel cap open warning
indicator
This warning light indicates the fuel filler
cap is not tight securely.
Always make sure that the fuel filler cap
is tight.
I
nf
or
mat
i
onPr
ovi
dedby:
4 51
Features of your vehicle
HAZARD WARNING FLASHER
ORB040045
The hazard warning flasher should be
used whenever you find it necessary to
stop the car in a hazardous location.
When you must make such an emergency stop, always pull off the road as far
as possible.
The hazard warning lights are turned on
by pushing in the hazard switch. This
causes all turn signal lights to blink. The
hazard warning lights will operate even
though the key is not in the ignition
switch.
To turn the hazard warning lights off,
push the switch a second time.
4 52
LIGHTING
Battery saver function (if equipped)
Headlight delay (if equipped)
• The purpose of this feature is to prevent the battery from being discharged. The system automatically
turns off the parking lights when the
driver removes the ignition key and
opens the driver-side door.
• With this feature, the parking lights will
be turned off automatically if the driver
parks on the side of road at night.
If necessary, to keep the lights on
when the ignition key is removed, perform the following:
1) Open the driver-side door.
2) Turn the parking lights OFF and ON
again using the light switch on the
steering column.
If you turn the ignition switch to the ACC
or OFF position with the headlights ON,
the headlights (and/or tail lights) remain
on for about 5 minutes. However, if the
driver’s door is opened and closed, the
headlights are turned off after 15 seconds.
The headlights can be turned off by
pressing the lock button on the transmitter twice or turning the light switch to the
OFF or AUTO position.
However, if you turn the light switch to the
AUTO position when it is dark outside,
the headlights will not be turned off.
CAUTION
If the driver gets out of the vehicle
through other doors, the battery
saver function does not operate.
Therefore, it causes the battery to
be discharged. In this case, make
sure to turn off the lamp before getting out of the vehicle.
I
nf
or
mat
i
onPr
ovi
dedby:
Features of your vehicle
Headlight welcome function
(if equipped)
Tail lamp warning chime
(if equipped)
When the headlight switch is in the ON or
AUTO position and all doors (and tailgate) are closed and locked, if you press
the door unlock button on the transmitter,
the headlights will come on for about 15
seconds.
If the headlight switch is in the AUTO
position, the function can only operate at
night.
At this time, if you press the door unlock
button again or door lock button on the
transmitter, the headlights will turn off
immediately.
If you turn the ignition switch to the OFF
position with the tail lamps ON and the
driver's door in an open position, the
warning chime will sound.
To stop the chime, perform one of the following:
1) Turn the ignition key to the ON position.
2) Turn the tail lamps OFF.
3) Close the driver's door.
CAUTION
To prevent the battery from being
discharged, make sure to turn off
the lamp before getting out of the
vehicle.
I
nf
or
mat
i
onPr
ovi
dedby:
ORB044046N
Lighting control
The light switch has a Headlight and a
Parking light position.
To operate the lights, turn the knob at the
end of the control lever to one of the following positions:
(1) OFF position
(2) Parking light position
(3) Headlight position
(4) Auto light position (if equipped)
4 53
Features of your vehicle
ORB040047D
ORB040048D
ORB044360N
Parking light position (
)
When the light switch is in the parking
light position, the tail, position and
license plate lights will turn on and the
tail light indicator will turn on.
Headlight position ( )
When the light switch is in the headlight
position the head, tail, license and instrument panel lights will turn on.
Auto light position (if equipped)
When the light switch is in the AUTO light
position, the taillights and headlights will
turn ON or OFF automatically depending
on the amount of light outside the vehicle.
✽ NOTICE
The ignition switch must be in the ON
position to turn on the headlights.
4 54
I
nf
or
mat
i
onPr
ovi
dedby:
Features of your vehicle
CAUTION
• Never place anything over sensor
(1) located on the instrument
panel. This will ensure better
auto-light system control.
• Don’t clean the sensor using a
window cleaner. The cleaner may
leave a light film which could
interfere with sensor operation.
• If your vehicle has window tint or
other types of metallic coating on
the front windshield, the Auto
light system may not work properly.
ORB040049D
High beam operation
To turn on the high beam headlights,
push the lever away from you. Pull it back
for low beams.
The high beam indicator will light when
the headlight high beams are switched on.
To prevent the battery from being discharged, do not leave the lights on for a
prolonged time while the engine is not
running.
ORB040050D
To flash the headlights, pull the lever
towards you. It will return to the normal
(low beam) position when released. The
headlight switch does not need to be on
to use this flashing feature.
WARNING
Do not use high beam when there
are other vehicles. Using high
beam could obstruct the other driver's vision.
I
nf
or
mat
i
onPr
ovi
dedby:
4 55
Features of your vehicle
To signal a lane change, move the turn
signal lever slightly and hold it in position
(B). The lever will return to the OFF position when released.
If an indicator stays on and does not
flash or if it flashes abnormally, one of the
turn signal bulbs may be burned out and
will require replacement.
ORB040051D
Turn signals and lane change signals
The ignition switch must be on for the
turn signals to function. To turn on the
turn signals, move the lever up or down
(A). Green arrow indicators on the instrument panel indicate which turn signal is
operating. They will self-cancel after a
turn is completed. If the indicator continues to flash after a turn, manually return
the lever to the OFF position.
4 56
One-touch lane change function
(if equipped)
To activate an one-touch lane change
function, move the turn signal lever
slightly and then release it. The lane
change signals will blink 3 times.
✽ NOTICE
If an indicator flash is abnormally quick
or slow, a bulb may be burned out or
have a poor electrical connection in the
circuit.
ORB040052D
Front fog light (if equipped)
Fog lights are used to provide improved
visibility when visibility is poor due to fog,
rain or snow etc. The fog lights will turn
on when fog light switch (1) is turned to
ON after the headlights are turned on.
To turn off the fog lights, turn the switch
to OFF.
CAUTION
When in operation, the fog lights
consume large amounts of vehicle
electrical power. Only use the fog
lights when visibility is poor or
unnecessary battery and generator
drain could occur.
I
nf
or
mat
i
onPr
ovi
dedby:
Features of your vehicle
WIPERS AND WASHERS
■ 4 Door
■ 5 Door
• Type A
■ 5 Door
• Type A
• Type A
• Type B
ORBC040054E
• Type B
OTA040053
• Type B
ORB044369
D : Rear wiper/washer control
(5 Door)
·
– Wash with brief wipes
· ON – Continuous wipe
· OFF – Off
ORB044054
A : Wiper speed control
· MIST – Single wipe
· OFF – Off
· INT – Intermittent wipe
(if equipped)
· LO – Low wiper speed
· HI – High wiper speed
ORB044368
B : Intermittent wipe time adjustment
(if equipped)
C : Wash with brief wipes (front)
(if equipped)
I
nf
or
mat
i
onPr
ovi
dedby:
4 57
Features of your vehicle
■ 4 Door
■ 5 Door
• Type A
• Type A
ORBC040055E
• Type B
OTA040055
• Type B
Operates as follows when the ignition
switch is turned ON.
MIST : For a single wiping cycle, push the
lever upward and release it with
the lever in the OFF position. The
wipers will operate continuously if
the lever is pushed upward and
held.
OFF : Wiper is not in operation
INT (if equipped) :
Wiper operates intermittently at
the same wiping intervals. Use
this mode in a light rain or mist. To
vary the speed setting, turn the
speed control knob.
LO : Normal wiper speed
HI
: Fast wiper speed
✽ NOTICE
ORB044055E
ORB044370
Windshield wipers
4 58
I
nf
or
mat
i
onPr
ovi
dedby:
If there is heavy accumulation of snow
or ice on the windshield, defrost the
windshield for about 10 minutes, or
until the snow and/or ice is removed
before using the windshield wipers to
ensure proper operation.
Features of your vehicle
CAUTION
When starting the vehicle in winter,
set the wiper switch in the OFF
position. Otherwise, wipers may
operate and ice may damage the
windshield wiper blades. Always
remove all snow and ice and defrost
the windshield properly prior to
operating the windshield wipers.
■ 4 Door
• Type A
• Type B
ORB044371
■ 5 Door
• Type A
• Type B
To use the windshield washer, pull the lever
gently toward you in the OFF position.
- Type A: The washer fluid will spray on
the windshield and the wipers
will operate 1~3 cycles.
- Type B: The washer fluid will spray on
the windshield but the wipers
will not operate.
Use this function when the windshield is
dirty.
The spray operation will continue until
you release the lever.
If the washer does not work, check the
washer fluid level. If the fluid level is not
sufficient, you will need to add appropriate non-abrasive windshield washer fluid
to the washer reservoir.
The reservoir filler neck is located in the
front of the engine compartment on the
passenger side.
CAUTION
ORB044372
Windshield washers
I
nf
or
mat
i
onPr
ovi
dedby:
To prevent possible damage to the
washer pump, do not operate the
washer when the fluid reservoir is
empty.
4 59
Features of your vehicle
WARNING
Do not use the washer in freezing
temperatures without first warming
the windshield with the defrosters;
the washer solution could freeze on
contact with the windshield and
obscure your vision.
■ 5 Door
• Type A
• Type B
CAUTION
• To prevent possible damage to
the wipers or windshield, do not
operate the wipers when the
windshield is dry.
• To prevent damage to the wiper
blades, do not use gasoline,
kerosene, paint thinner, or other
solvents on or near them.
• To prevent damage to the wiper
arms and other components, do
not attempt to move the wipers
manually.
ORB044373
Rear window wiper and washer
switch (5 Door)
The rear window wiper and washer
switch is located at the end of the wiper
and washer switch lever. Turn the switch
to desired position to operate the rear
wiper and washer.
- Spraying washer fluid and wiping
ON - Normal wiper operation
OFF - Wiper is not in operation
4 60
I
nf
or
mat
i
onPr
ovi
dedby:
Features of your vehicle
INTERIOR LIGHT
CAUTION
Do not use the interior lights for
extended periods when the engine
is not running.
It may cause battery discharge.
WARNING
Do not use the interior lights when
driving in the dark. Accidents could
happen because the view may be
obscured by interior lights.
Automatic turn off function
(if equipped)
The interior lights automatically turn off
approximately 20 minutes after the ignition switch is turned off.
ORB040057
Map lamp
Push the lens (1) to turn the map lamp on
or off. This light produces a spot beam for
convenient use as a map lamp at night or
as a personal lamp for the driver and the
front passenger.
I
nf
or
mat
i
onPr
ovi
dedby:
• DOOR :
In the DOOR position, the map lamp and
the room lamp come on when any door is
opened regardless of the ignition switch
position.
When doors are unlocked by the transmitter, the map lamp and the room lamp
come on for approximately 30 seconds
as long as any door is not open. The map
lamp and the room lamp goes out gradually after approximately 30 seconds if the
door is closed. However, if the ignition
switch is ON or all doors are locked, the
map lamp and the room lamp will turn off
immediately. If a door is opened with the
ignition switch in the ACC or LOCK position, the map lamp and the room lamp
stay on for about 20 minutes. However, if
a door is opened with the ignition switch
in the ON position, the map lamp and the
room lamp stay on continuously.
4 61
Features of your vehicle
• ON :
Map lamp and room lamp stay on at all
times.
• OFF :
The lights turn off even if a door is
opened.
❈ When the lamp is turned ON by pressing the lens (1) the lamp does not turn
off even if the switch (2) is in the OFF
position.
ORB040361
Room lamp
• ON (1):
In the ON position, the light stays on at all
times.
• DOOR (2) :
In the DOOR position, the light comes on
when any door is opened regardless of
the ignition switch position.
When doors are unlocked by the transmitter, the light comes on for approximately 30 seconds as long as any door is
not open. The light goes out gradually
after approximately 30 seconds if the
door is closed. However, if the ignition
switch is ON or all doors are locked, the
light will turn off immediately.
If a door is opened with the ignition
switch in the ACC or LOCK position, the
light stays on for about 20 minutes.
However, if a door is opened with the
ignition switch in the ON position, the
light stays on continuously.
• OFF (3) :
In the OFF position, the light stays off at
all times even when a door is open.
4 62
I
nf
or
mat
i
onPr
ovi
dedby:
Features of your vehicle
4 Door
CAUTION
The luggage room lamp comes on
as long as the trunk lid/tailgate
opens. To prevent unnecessary
charging system drain, close the
trunk lid/tailgate securely after
using the luggage room.
ORBC040059
5 Door
ORB041402
Luggage room lamp
The luggage room lamp comes on when
the trunk lid/tailgate is opened.
I
nf
or
mat
i
onPr
ovi
dedby:
4 63
Features of your vehicle
DEFROSTER
Outside rearview mirror defroster
(if equipped)
If your vehicle is equipped with the outside rearview mirror defrosters, they will
operate at the same time you turn on the
rear window defroster.
CAUTION
To prevent damage to the conductors bonded to the inside surface of
the rear window, never use sharp
instruments or window cleaners
containing abrasives to clean the
window.
✽ NOTICE
If you want to defrost and defog the
front windshield, refer to “Windshield
defrosting and defogging” in this section.
ORB040063L
Rear window defroster
The defroster heats the window to
remove frost, fog and thin ice from the
rear window, while the engine is running.
To activate the rear window defroster,
press the rear window defroster button
located in the center facia switch panel.
The indicator on the rear window
defroster button illuminates when the
defroster is ON.
If there is heavy accumulation of snow on
the rear window, brush it off before operating the rear defroster.
The rear window defroster automatically
turns off after approximately 20 minutes
or when the ignition switch is turned off.
To turn off the defroster, press the rear
window defroster button again.
4 64
I
nf
or
mat
i
onPr
ovi
dedby:
Features of your vehicle
MANUAL CLIMATE CONTROL SYSTEM
1. Temperature control knob
2. Fan speed control knob
3. Air conditioning button
4. Air intake control button
5. Mode selection knob
ORB040065N
I
nf
or
mat
i
onPr
ovi
dedby:
4 65
Features of your vehicle
Heating and air conditioning
1. Start the engine.
2. Set the mode to the desired position.
For improving the effectiveness of
heating and cooling;
- Heating:
- Cooling:
3. Set the temperature control to the
desired position.
4. Set the air intake control to the outside
(fresh) air position.
5. Set the fan speed control to the
desired speed.
6. If air conditioning is desired, turn the
air conditioning system on.
ORB040066
4 66
I
nf
or
mat
i
onPr
ovi
dedby:
Features of your vehicle
Face-Level (B, D)
Air flow is directed toward the upper body
and face. Additionally, each outlet can be
controlled to direct the air discharged
from the outlet.
Bi-Level (B, D, E, C)
ORB040067
Mode selection
The mode selection knob controls the
direction of the air flow through the ventilation system.
Air can be directed to the floor, dashboard outlets, or windshield. Five symbols are used to represent Five, Face, BiLevel, Floor, Floor-Defrost and Defrost
air position.
Air flow is directed towards the face and
the floor.
Floor-Level (C, A, D, E)
Most of the air flow is directed to the
floor, with a small amount of the air being
directed to the windshield and side window defrosters.
Floor/Defrost-Level (A, C, D, E)
Most of the air flow is directed to the floor
and the windshield with a small amount
directed to the side window defrosters.
Defrost-Level (A, D)
Most of the air flow is directed to the
windshield with a small amount of air
directed to the side window defrosters.
I
nf
or
mat
i
onPr
ovi
dedby:
4 67
Features of your vehicle
ORB040356
ORB040068
ORB040069
MAX A/C-Level (B, D, E)
To select the MAX A/C, turn the temperature knob to the extreme the left.
Air flow is directed toward the upper body
and face.
In this mode, the air conditioning and the
recirculated air position will be selected
automatically.
Instrument panel vents
The outlet vents can be opened or closed
separately using the horizontal thumbwheel. To close the vent, rotate it left to
the maximum position. To open the vent,
rotate it right to the desired position.
Also, you can adjust the direction of air
delivery from these vents using the vent
control lever as shown.
Temperature control
The temperature control knob allows you
to control the temperature of the air flowing from the ventilation system. To
change the air temperature in the passenger compartment, turn the knob to
the right position for warm and hot air or
left position for cooler air.
✽ NOTICE
This setting should be used briefly to
help quickly cool the interior. After the
interior temperature has cooled sufficiently, turn the temperature knob away
from the MAX A/C position to a comfortable setting.
4 68
I
nf
or
mat
i
onPr
ovi
dedby:
Features of your vehicle
Recirculated air position
With the recirculated
air position selected,
air from the passenger compartment will
be drawn through the
heating system and
heated or cooled
according to the
function selected.
ORB040070
Air intake control
The air intake control is used to select
the outside (fresh) air position or recirculated air position.
To change the air intake control position,
press the control button.
Outside (fresh) air position
With the outside
(fresh) air position
selected, air enters
the vehicle from outside and is heated or
cooled according to
the function selected.
✽ NOTICE
WARNING
• Continue using the climate control system in the recirculated air
position may allow humidity to
increase inside the vehicle which
may fog the glass and obscure
visibility.
• Do not sleep in a vehicle with the
air conditioning or heating system on. It may cause serious
harm or death due to a drop in the
oxygen level and/or body temperature.
• Continue using the climate control
system in the recirculated air
position can cause drowsiness or
sleepiness, and loss of vehicle
control. Set the air intake control
to the outside (fresh) air position
as much as possible while driving.
Prolonged operation of the heater in the
recirculated air position (without air
conditioning selected) may cause fogging of the windshield and side windows
and the air within the passenger compartment may become stale.
In addition, prolonged use of the air conditioning with the recirculated air position selected will result in excessively dry
air in the passenger compartment.
I
nf
or
mat
i
onPr
ovi
dedby:
4 69
Features of your vehicle
ORB040073N
ORB043099N
ORB040354N
Fan speed control
The ignition switch must be in the ON
position for fan operation.
The fan speed control knob allows you to
control the fan speed of the air flowing
from the ventilation system. To change
the fan speed, turn the knob to the right
for higher speed or left for lower speed.
Setting the fan speed control knob to the
“0” position turns off the fan.
To turn off the blowers
To turn off the blowers, turn the fan
speed control knob to the "0" position.
Air conditioning
Press the A/C button to turn the air conditioning system on (indicator light will
illuminate). Press the button again to turn
the air conditioning system off.
4 70
I
nf
or
mat
i
onPr
ovi
dedby:
Features of your vehicle
System operation
Ventilation
1. Set the mode to the
position.
2. Set the air intake control to the outside
(fresh) air position.
3. Set the temperature control to the
desired position.
4. Set the fan speed control to the
desired speed.
Heating
1. Set the mode to the
position.
2. Set the air intake control to the outside
(fresh) air position.
3. Set the temperature control to the
desired position.
4. Set the fan speed control to the
desired speed.
5. If dehumidified heating is desired, turn
the air conditioning system (if
equipped) on.
• If the windshield fogs up, set the mode
to the
or
position.
Operation Tips
• To keep dust or unpleasant fumes from
entering the vehicle through the ventilation system, temporarily set the air
intake control to the recirculated air
position. Be sure to return the control
to the fresh air position when the irritation has passed to keep fresh air in the
vehicle. This will help keep the driver
alert and comfortable.
• Air for the heating/cooling system is
drawn in through the grilles just ahead
of the windshield. Care should be
taken that these are not blocked by
leaves, snow, ice or other obstructions.
• To prevent interior fog on the windshield, set the air intake control to the
fresh air position and fan speed to the
desired position, turn on the air conditioning system, and adjust the temperature control to desired temperature.
I
nf
or
mat
i
onPr
ovi
dedby:
Air conditioning
HYUNDAI Air Conditioning Systems are
filled with environmentally friendly
R-134a refrigerant.
1. Start the engine. Press the air conditioning button.
2. Set the mode to the
position.
3. Set the air intake control to the outside
air or recirculated air position.
4. Adjust the fan speed control and temperature control to maintain maximum
comfort.
• When maximum cooling is desired, set
the temperature control to the extreme
left position (the MAX A/C position),
then set the fan speed control to the
highest speed.
4 71
Features of your vehicle
✽ NOTICE
• When using the air conditioning system, monitor the temperature gauge
closely while driving up hills or in
heavy traffic when outside temperatures are high. Air conditioning system operation may cause engine overheating. Continue to use the blower
fan but turn the air conditioning system off if the temperature gauge indicates engine overheating.
• When opening the windows in humid
weather air conditioning may create
water droplets inside the vehicle.
Since excessive water droplets may
cause damage to electrical equipment,
air conditioning should only be used
with the windows closed.
4 72
Air conditioning system operation tips
• If the vehicle has been parked in direct
sunlight during hot weather, open the
windows for a short time to let the hot
air inside the vehicle escape.
• To help reduce moisture inside of the
windows on rainy or humid days,
decrease the humidity inside the vehicle by operating the air conditioning
system.
• During air conditioning system operation, you may occasionally notice a
slight change in engine speed as the
air conditioning compressor cycles.
This is a normal system operation
characteristic.
• Use the air conditioning system every
month only for a few minutes to ensure
maximum system performance.
I
nf
or
mat
i
onPr
ovi
dedby:
• When using the air conditioning system, you may notice clear water dripping (or even puddling) on the ground
under the passenger side of the vehicle. This is a normal system operation
characteristic.
• Operating the air conditioning system
in the recirculated air position provides
maximum cooling, however, continual
operation in this mode may cause the
air inside the vehicle to become stale.
• During cooling operation, you may
occasionally notice a misty air flow
because of rapid cooling and humid air
intake. This is a normal system operation characteristic.
• If you operate air conditioner excessively, the difference between the temperature of the outside air and that of
the windshield could cause the outer
surface of the windshield to fog up,
causing loss of visibility. In this case,
set the mode selection knob or button
to the
position and fan speed control to the lower speed.
Features of your vehicle
✽ NOTICE
Outside air
Recirculated
air
Blower Evaporator core
Climate control air filter
Heater core
• Replace the filter according to the
Maintenance Schedule.
If the vehicle is being driven in severe
conditions such as dusty or rough
roads, more frequent air conditioner
filter inspections and changes are
required.
• When the air flow rate suddenly
decreases, the system should be
checked at an authorized HYUNDAI
dealer.
OHM048209
Checking the amount of air conditioner refrigerant and compressor lubricant
When the amount of refrigerant is low,
the performance of the air conditioning is
reduced. Overfilling also has a negative
impact on the air conditioning system.
Therefore, if abnormal operation is
found, have the system inspected by an
authorized HYUNDAI dealer.
✽ NOTICE
It is important that the correct type and
amount of oil and refrigerant is used.
Otherwise, damage to the compressor
and abnormal system operation may
occur.
Climate control air filter
(if equipped)
The climate control air filter installed
behind the glove box filters the dust or
other pollutants that come into the vehicle from the outside through the heating
and air conditioning system. If dust or
other pollutants accumulate in the filter
over a period of time, the air flow from the
air vents may decrease, resulting in
moisture accumulation on the inside of
the windshield even when the outside
(fresh) air position is selected. If this happens, have the climate control air filter
replaced by an authorized HYUNDAI
dealer.
WARNING
The air conditioning system should
be serviced by an authorized
HYUNDAI dealer. Improper service
may cause serious injury to the
person performing the service.
I
nf
or
mat
i
onPr
ovi
dedby:
4 73
Features of your vehicle
AUTOMATIC CLIMATE CONTROL SYSTEM (IF EQUIPPED)
1. AUTO (automatic control) button
2. OFF button
3. Temperature control knob
4. A/C display
5. Air intake control button
6. Fan speed control knob
7. Air conditioning button
8. Mode selection button
9. Front windshield defrost button.
ORB040340N
4 74
I
nf
or
mat
i
onPr
ovi
dedby:
Features of your vehicle
ORB040342
Automatic heating and air conditioning
1. Press the AUTO button.
The modes, fan speeds, air intake and
air-conditioning will be controlled automatically according to the temperature
setting.
ORB040341
2. Turn the temperature control knob to
set the desired temperature.
✽ NOTICE
• To turn the automatic operation off,
select any button of the following:
- Mode selection button
- Front windshield defrost button
- Fan speed control button
The selected function will be controlled manually while other functions
operate automatically.
• For your convenience and to improve
the effectiveness of the climate control, use the AUTO button and set the
temperature to 23°C (73°F).
I
nf
or
mat
i
onPr
ovi
dedby:
ORB040353
✽ NOTICE
Never place anything over the sensor
located on the instrument panel to
ensure better control of the heating and
cooling system.
4 75
Features of your vehicle
Manual heating and air conditioning
The heating and cooling system can be
controlled manually by pushing buttons
other than the AUTO button. In this case,
the system works sequentially according
to the order of buttons selected.
When pressing any button except the
AUTO button while using automatic operation, the functions not selected will be
controlled automatically.
1. Start the engine.
2. Set the mode to the desired position.
For improving the effectiveness of
heating and cooling;
- Heating:
- Cooling:
3. Set the temperature control to the
desired position.
4. Set the air intake control to the outside
(fresh) air position.
5. Set the fan speed control to the
desired speed.
6. If air conditioning is desired, turn the
air conditioning system on.
Press the AUTO button in order to convert to full automatic control of the system.
4 76
Floor & Defrost
Most of the air flow is directed to the floor
and the windshield with a small amount
directed to the side window defrosters.
Face-Level
ORB040347N
Mode selection
The mode selection button controls the
direction of the air flow through the ventilation system.
The air flow outlet port is converted as
follows:
Air flow is directed toward the upper body
and face. Additionally, each outlet can be
controlled to direct the air discharged
from the outlet.
Bi-Level
Air flow is directed towards the face and
the floor.
Refer to the illustration in the “Manual climate control system”.
I
nf
or
mat
i
onPr
ovi
dedby:
Floor-Level
Most of the air flow is directed to the
floor, with a small amount of the air being
directed to the windshield and side window defrosters.
Features of your vehicle
ORB040355N
ORB040068
ORB040341
Defrost-Level
Most of the air flow is directed to the
windshield with a small amount of air
directed to the side window defrosters.
Instrument panel vents
The outlet vents can be opened or closed
separately using the horizontal thumbwheel. To close the vent, rotate it left to
the maximum position. To open the vent,
rotate it right to the desired position.
Also, you can adjust the direction of air
delivery from these vents using the vent
control lever as shown.
Temperature control
The temperature will increase to the
maximum by turning the knob to the right
extremely.
The temperature will decrease to the
minimum by turning the knob to the left
extremely.
When turning the knob, the temperature
will increase or decrease by 1°F (0.5°C).
When set to the lowest temperature setting, the air conditioning will operate continuously.
I
nf
or
mat
i
onPr
ovi
dedby:
4 77
Features of your vehicle
Recirculated air position
With the recirculated air
position selected, air from
the passenger compartment will be drawn through
the heating system and
heated or cooled according
to the function selected.
ORB040345N
Air intake control
This is used to select the outside (fresh)
air position or recirculated air position.
To change the air intake control position,
push the control button.
4 78
Outside (fresh) air position
■ Type A
With the outside (fresh) air
position
selected,
air
enters the vehicle from outside and is heated or
cooled according to the
■ Type B
function selected.
I
nf
or
mat
i
onPr
ovi
dedby:
✽ NOTICE
Prolonged operation of the heater in the
recirculated air position (without air
conditioning selected) may cause fogging of the windshield and side windows
and the air within the passenger compartment may become stale.
In addition, prolonged use of the air conditioning with the recirculated air position selected will result in excessively dry
air in the passenger compartment.
Features of your vehicle
WARNING
• Continued climate control system
operation in the recirculated air
position may allow humidity to
increase inside the vehicle which
may fog the glass and obscure
visibility.
• Do not sleep in a vehicle with the
air conditioning or heating system
on. It may cause serious harm or
death due to a drop in the oxygen
level and/or body temperature.
• Continued climate control system
operation in the recirculated air
position can cause drowsiness or
sleepiness, and loss of vehicle
control. Set the air intake control
to the outside (fresh) air position
as much as possible while driving.
ORB040344N
ORB040346N
Fan speed control
The fan speed can be set to the desired
speed by turning the fan speed control
knob.
The higher the fan speed is, the more air
is delivered.
Pressing the OFF button turns off the
fan.
Air conditioning
Push the A/C button to turn the air conditioning system on (indicator light will illuminate).
Push the button again to turn the air conditioning system off.
I
nf
or
mat
i
onPr
ovi
dedby:
4 79
Features of your vehicle
ORB040343
OFF mode
Push the OFF button to turn off the air climate control system. However, you can
still operate the mode and air intake buttons as long as the ignition switch is in
the ON position.
4 80
I
nf
or
mat
i
onPr
ovi
dedby:
Features of your vehicle
WINDSHIELD DEFROSTING AND DEFOGGING
WARNING - Windshield
heating
Do not use the
or
position
during cooling operation in
extremely humid weather. The difference between the temperature of
the outside air and that of the windshield could cause the outer surface of the windshield to fog up,
causing loss of visibility. In this
case, set the mode selection knob
or button to the
position and
fan speed control knob or button to
the lower speed.
• For maximum defrosting, set the temperature control to the extreme
right/hot position and the fan speed
control to the highest speed.
• If warm air to the floor is desired while
defrosting or defogging, set the mode
to the floor-defrost position.
• Before driving, clear all snow and ice
from the windshield, rear window, outside rear view mirrors, and all side windows.
• Clear all snow and ice from the hood
and air inlet in the cowl grill to improve
heater and defroster efficiency and to
reduce the probability of fogging up the
inside of the windshield.
I
nf
or
mat
i
onPr
ovi
dedby:
ORB040075N
Manual climate control system
To defog inside windshield
1. Set the fan speed to the desired position.
2. Select desired temperature.
3. Select the
or
position.
4. The outside (fresh) air will be selected
automatically. If the
position is
selected, air conditioning will also be
selected automatically.
If the air conditioning and/or outside
(fresh) air position are not selected automatically, press the corresponding button
manually.
4 81
Features of your vehicle
ORB040076N
To defrost outside windshield
1. Set the fan speed to the highest position.
2. Set the temperature to the extreme hot
position.
3. Select the
position.
4. The outside (fresh) air and air conditioning will be selected automatically.
4 82
ORB040348N
Automatic climate control system
To defog inside windshield
1. Set the fan speed to the desired position.
2. Select desired temperature.
3. Press the defrost button (
).
4. The air conditioning will be turned on
according to the detected ambient temperature and outside (fresh) air position will be selected automatically.
If the air conditioning and outside (fresh)
air position are not selected automatically, adjust the corresponding button manually. If the
position is selected,
lower fan speed is adjusted to a higher
fan speed.
I
nf
or
mat
i
onPr
ovi
dedby:
ORB040349N
To defrost outside windshield
1. Set the fan speed to the highest
(extreme right) position.
2. Set the temperature to the extreme hot
(HI) position.
3. Press the defrost button (
).
4. The air conditioning will be turned on
according to the detected ambient
temperature and outside (fresh) air
position will be selected automatically.
If the
position is selected, lower fan
speed is adjusted to a higher fan speed.
Features of your vehicle
Defogging logic
To reduce the probability of fogging up
the inside of the windshield, the air intake
or air conditioning are controlled automatically according to certain conditions
such as
or
position. To cancel or
return the defogging logic, do the following.
ORB040077N
ORB040350N
Manual climate control system
1. Turn the ignition switch to the ON position.
2. Select the defrost button (
).
3. Press the air intake control button at
least 5 times within 3 seconds.
The indicator on the air intake button
blinks 3 times with 0.5 second of interval.
It indicates that the defogging logic is
canceled or returned to the programmed
status.
Automatic climate control system
1. Turn the ignition switch to the ON position.
2. Press the defrost button (
).
3. While holding the air conditioning
(A/C) button pressed, press the air
intake control button (recirculated air
position) at least 5 times within 3 seconds.
The A/C display blinks 3 times with 0.5
second of interval. It indicates that the
defogging logic is canceled or returned to
the programmed status.
If the battery has been discharged or disconnected, it resets to the defog logic
status.
I
nf
or
mat
i
onPr
ovi
dedby:
If the battery has been discharged or disconnected, it resets to the defog logic
status.
4 83
Features of your vehicle
STORAGE COMPARTMENTS
These compartments can be used to
store small items.
CAUTION
• To avoid possible theft, do not
leave valuables in the storage
compartments.
• Always keep the storage compartment covers closed while
driving. Do not attempt to place
so many items in the storage
compartment that the storage
compartment cover cannot close
securely.
ORB040351
ORB040362
Center console storage
Sliding armrest (if equipped)
To open the center console storage, pull
up the lever.
To move forward
Grab the front portion of the armrest (1)
then pull it forward.
WARNING - Flammable
materials
To move rearward
Push the armrest rearward with your
palm.
Do not store cigarette lighters,
propane cylinders, or other flammable/explosive materials in the vehicle. These items may catch fire
and/or explode if the vehicle is
exposed to hot temperatures for
extended periods.
4 84
WARNING
Do not grap the front portion of the
armrest (1) when moving the armrest rearward. It may pinch your fingers.
I
nf
or
mat
i
onPr
ovi
dedby:
Features of your vehicle
WARNING
ORB040080
ORB040081
Glove box
Sunglass holder (if equipped)
To open the glove box, push the button
and the glove box will automatically
open. Close the glove box after use.
To open the sunglass holder, press the
cover and the holder will slowly open.
Place your sunglasses in the compartment door with the lenses facing out.
Push to close.
WARNING
To reduce the risk of injury in an
accident or sudden stop, always
keep the glove box door closed
while driving.
• Do not keep objects except sunglasses inside the sunglass holder. Such objects can be thrown
from the holder in the event of a
sudden stop or an accident, possibly injuring the passengers in
the vehicle.
• Do not open the sunglass holder
while the vehicle is moving. The
rear view mirror of the vehicle
can be blocked by an open sunglass holder.
• Do not put the glasses forcibly
into a sunglass holder to prevent
breakage or deformation of
glasses. It may cause personal
injury if you try to open it forcibly
when the glasses are jammed in
holder.
CAUTION
Do not keep food in the glove box
for a long time.
I
nf
or
mat
i
onPr
ovi
dedby:
4 85
Features of your vehicle
CAUTION
To prevent damage to the goods or
the vehicle, care should be taken
when carrying fragile or bulky
objects in the luggage compartment.
WARNING
OYF049225
Luggage net (holder)
(if equipped)
To keep items from shifting in the cargo
area, you can use the holders located in
the cargo area to attach the luggage net.
4 86
Avoid eye injury. DO NOT overstretch the luggage net, ALWAYS
keep your face and body out of the
luggage net’s recoil path. DO NOT
use when the strap has visible
signs of wear or damage.
I
nf
or
mat
i
onPr
ovi
dedby:
Features of your vehicle
INTERIOR FEATURES
Cup holder
WARNING - Hot liquids
• Do not place uncovered cups of
hot liquid in the cup holder while
the vehicle is in motion. If the hot
liquid spills, you may burn yourself. Such a burn to the driver
could lead to loss of control of
the vehicle.
• To reduce the risk of personal
injury in the event of sudden stop
or collision, do not place uncovered or unsecured bottles, glasses, cans, etc., in the cup holder
while the vehicle is in motion.
Cups or small beverage cans may be
placed in the cup holders.
CAUTION
WARNING
Keep cans or bottles out of direct
sun light and do not put them in a
vehicle that is heated up. It may
explode.
ORB044085N
ORB040078
Do not place uncovered cups in the
cup holder while the vehicle is in
motion. If the liquid spills, electric
systems may malfunction.
Sunvisor
Use the sunvisor to shield direct light
through the front or side windows.
To use a sunvisor, pull it downward.
To use a sunvisor for a side window, pull
it downward, unsnap it from the bracket
(1) and swing it to the side (2).
To use the vanity mirror, pull down the
visor and slide the mirror cover (3).
Adjust the sunvisor extension forward or
rearward (4).
The ticket holder (5) is provided for holding a tollgate ticket. (if equipped)
WARNING
For your safety, do not obstruct your
vision when using the sunvisor.
I
nf
or
mat
i
onPr
ovi
dedby:
4 87
Features of your vehicle
CAUTION
ORB041084N
Power outlet
The power outlet is designed to provide
power for mobile telephones or other
devices designed to operate with vehicle
electrical systems. The devices should
draw less than 10 amps with the engine
running.
4 88
• Use the power outlet only when
the engine is running and remove
the accessory plug after use.
Using the accessory plug for prolonged periods of time with the
engine off could cause the battery to discharge.
• Only use 12V electric accessories
which are less than 10A in electric capacity. If not, it could lead
to an overheated power outlet or
electric wiring in the vehicle and
electric systems may malfunction.
• Adjust the air-conditioner or
heater to the lowest operating
level when using the power outlet.
• Close the cover when not in use.
• Some electronic devices can
cause electronic interference
when plugged into a vehicle’s
power outlet. These devices may
cause excessive audio static and
malfunctions in other electronic
systems or devices used in your
vehicle.
(Continued)
I
nf
or
mat
i
onPr
ovi
dedby:
(Continued)
• Make sure that the electric
devices are plugged in securely. If
not, it could cause a malfunction
of electric systems.
• If you use an electric device with
a battery, electric current may
flow from the electric device into
the vehicle and may cause a malfunction of electric systems. Only
use electric devices which could
prevent inverse current.
WARNING
Do not put a finger or a foreign element (pin, etc.) into a power outlet
and do not touch with a wet hand.
You may get an electric shock.
Features of your vehicle
Setup the clock
With audio off
1. Press the [SETUP] button until the
clock of the display blinks.
2. Set the clock by turning the knob(1)
and press it.
ORB044086N
Digital clock (if equipped)
With audio on
1. Press the [SETUP] button.
2. Select the [CLOCK] mode by turning
the knob(1) and press it.
3. Set the clock by turning the knob(1)
and press it.
OUN026348
Clothes hanger (if equipped)
To use the hanger, pull down the upper
portion of hanger.
WARNING
Do not adjust the clock while driving. You may lose your steering
control and cause an accident that
results in severe personal injury or
death.
CAUTION
Do not hang heavy clothes,
because it may damage the hook.
Whenever the battery terminals or related fuses are disconnected, you must
reset the time.
When the ignition switch is in the ACC or
ON position, the clock buttons operate as
follows:
I
nf
or
mat
i
onPr
ovi
dedby:
4 89
Features of your vehicle
WARNING
OMD040195N
Floor mat anchor(s)
When using a floor mat on the front floor
carpet, make sure it attaches to the floor
mat anchor(s) in your vehicle. This keeps
the floor mat from sliding forward.
WARNING
The floor mat must be properly
anchored so that it will not interfere
with the operation of the accelerator pedal. Any interference with the
accelerator pedal could cause the
accelerator pedal to be unable to
return to the idle position. A pedal
that cannot return to the idle position could lead to an accident
which may result in severe personal injury or death.
4 90
The following must be observed
when installing ANY floor mat to
the vehicle, so that it will not interfere with the pedal.
• Ensure that the floor mats are
securely attached to the vehicle’s
floor mat anchor(s) before driving
the vehicle.
• Do not use ANY floor mat that
cannot be firmly attached to the
vehicle’s floor mat anchors.
• Do not stack floor mats on top of
one another (e.g. all-weather rubber mat on top of a carpeted floor
mat). Only a single floor mat
should be installed in each position.
IMPORTANT – Your vehicle was
manufactured with driver’s side
floor mat anchors that are designed
to securely hold the floor mat in
place. To avoid any interference
with pedal operation, HYUNDAI recommends that only the HYUNDAI
floor mat designed for use in your
vehicle be installed.
I
nf
or
mat
i
onPr
ovi
dedby:
ORB041403
Cargo area cover (if equipped)
Use the cover to hide items stored in the
cargo area.
The cargo area cover will be lifted when
the tailgate is opened. Disconnect the
strap (1) from holder if you want to return
the cover to original position. To remove
the cargo area cover completely, lift the
cover to a 50-degree angle and pull it out
to the full (2). For installation of the cover,
reverse the removal procedure.
Features of your vehicle
Bluetooth® Wireless Technology
hands-free (if equipped)
CAUTION
• When you return the cargo area
cover to its original position, hold
the cover and lower it.
• Do not operate the vehicle with
the cover removed. It may damage to the cover.
• The cargo area cover may be lifted when the tailgate is opened.
Ensure that the luggage on the
cover is moved to a safe place.
• Since the cargo area cover may be
damaged or malformed, do not
apply excessive force to the cover
or do not put the heavy loads on it.
WARNING
• Do not place objects on the cargo
area cover while driving. Such
objects may be thrown about
inside the vehicle and possibly
injure vehicle occupants during
an accident or when braking.
• Never allow anyone to ride in the
luggage compartment. It is
designed for luggage only.
• Maintain the balance of the vehicle and locate the weight as far
forward as possible.
You can use a Bluetooth® Wireless
Technology phone.
Detailed information for the Bluetooth®
Wireless Technology hands-free is
described in the “Audio section” in this
chapter or in the manual supplied separately.
ORB044087N
Aux, USB and iPod port
®
If your vehicle has an aux and/or
USB(universal serial bus) port or iPod®
port, you can use an aux port to connect
audio devices and an USB port to plug in
an USB and also an iPod® port to plug in
an iPod®.
✽ NOTICE
When using a portable audio device
connected to the power outlet, noise may
occur during playback. If this happens,
use the power source of the portable
audio device.
❈ iPod® is a trademark of Apple Inc.
I
nf
or
mat
i
onPr
ovi
dedby:
4 91
Features of your vehicle
EXTERIOR FEATURES
WARNING
Use a coin or flat blade driver when
you remove the roof carrier cover.
If you use your fingernail, it may
injure your finger.
OED046090
OED046091
Mounting bracket for roof carrier
(if equipped)
2. Rotate the cover half way and insert
the cover on the roof hole as the illustration.
To install or remove a roof carrier, you
can use the mounting bracket and cover
on the roof.
When you install a roof carrier, use
approved HYUNDAI accessories and do
the following procedure.
1. Insert a slim tool (coin or flat blade
driver) into the slot and slide the cover
toward the arrow on the cover.
4 92
✽ NOTICE
To prevent losing the roof carrier cover,
install the cover on the roof before you
install the roof carrier.
3. After using the roof carrier, install the
cover back on the roof in the reverse
order.
I
nf
or
mat
i
onPr
ovi
dedby:
Features of your vehicle
✽ NOTICE
If the vehicle is equipped with a sunroof,
be sure not to position cargo onto the
roof in such a way that it could interfere
with sunroof operation.
CAUTION
• When carrying cargo on the roof,
take the necessary precautions to
make sure the cargo does not
damage the roof of the vehicle.
• When carrying large objects on
the roof, make sure they do not
exceed the overall roof length or
width.
WARNING
• The vehicle center of gravity will
be higher when items are loaded
onto the roof. Avoid sudden
starts, braking, sharp turns,
abrupt maneuvers or high speeds
that may result in loss of vehicle
control or rollover resulting in an
accident.
• Always drive slowly and turn corners carefully when carrying
items on the roof. Severe wind
updrafts, caused by passing
vehicles or natural causes, can
cause sudden upward pressure
on items loaded on the roof. This
is especially true when carrying
large, flat items such as wood
panels or mattresses. This could
cause the items to fall off the roof
and cause damage to your vehicle or others around you.
• To prevent damage or loss of
cargo while driving, check frequently before or while driving to
make sure the items on the roof
are securely fastened.
I
nf
or
mat
i
onPr
ovi
dedby:
4 93
Features of your vehicle
AUDIO SYSTEM
✽ NOTICE
CAUTION
If you install an after market HID (high
intensity discharge) head lamp, your
vehicle's audio and electronic device
may malfunction.
ORB040088
Antenna
Roof antenna
Your car uses a roof antenna to receive
both AM and FM broadcast signals. This
antenna is a removable type. To remove
the antenna, turn it counterclockwise. To
install the antenna, turn it clockwise.
4 94
I
nf
or
mat
i
onPr
ovi
dedby:
• Before entering a place with a low
height clearance or a car wash,
remove surely the antenna by
rotating it counter-clockwise. If
not, the antenna may be damaged.
• When reinstalling your antenna, it
is important that it is fully tightened and adjusted to the upright
position to ensure proper reception. But it could be folded or
removed when parking the vehicle or when loading cargo on the
roof rack.
• When cargo is loaded on the roof
rack, do not place the cargo near
the antenna pole to ensure proper
reception.
Features of your vehicle
Type A
2
1
4
3
ORB040089
Type B
VOLUME (VOL +/-) (1)
• Press the up button (+) to increase volume.
• Press the down button (-) to decrease
volume.
MUTE (2)
• Press the MUTE button to cancel the
sound.
• Press the MUTE button again to activate the sound.
4
1
MODE (3)
Press the MODE button to select Radio,
CD (Compact Disc).
3
SEEK/PRESET (
/
) (4)
If the SEEK/PRESET button is pressed
for 0.8 second or more, it will work as follows in each mode.
RADIO mode
It will function as the AUTO SEEK select
button. It will SEEK until you release the
button.
CDP mode
It will function as the FF/REW button.
If the SEEK/PRESET button is pressed
for less than 0.8 second, it will work as
follows in each mode.
RADIO mode
It will function as the PRESET STATION
select buttons.
CDP mode
It will function as the TRACK UP/DOWN
button.
PA710RBU SW
Steering wheel audio control
(if equipped)
The steering wheel audio control button
is installed to promote safe driving.
Detailed information for audio control
buttons is included in the following pages
in this section.
CAUTION
Do not operate audio remote control buttons simultaneously.
I
nf
or
mat
i
onPr
ovi
dedby:
4 95
Features of your vehicle
FM reception
AM reception
JBM001
How vehicle audio works
AM and FM radio signals are broadcast
from transmitter towers located around
your city. They are intercepted by the
radio antenna on your vehicle. This signal
is then processed by the radio and sent
to your vehicle speakers.
When a strong radio signal has reached
your vehicle, the precise engineering of
your audio system ensures the best possible quality reproduction. However, in
some cases the signal coming to your
vehicle may not be strong and clear.
This can be due to factors, such as the
distance from the radio station, closeness of other strong radio stations or the
presence of buildings, bridges or other
large obstructions in the area.
4 96
FM radio station
JBM002
JBM003
AM broadcasts can be received at
greater distances than FM broadcasts.
This is because AM radio waves are
transmitted at low frequencies. These
long distance,low frequency radio waves
can follow the curvature of the earth
rather than travelling straight. In addition,
they curve around obstructions resulting
in better signal coverage.
FM broadcasts are transmitted at high
frequencies and do not bend to follow the
earth's surface. Because of this, FM
broadcasts generally begin to fade within
short distances from the station. short
distances from the station. Also, FM signals are easily affected by buildings,
mountains, and obstructions. This can
lead to undesirable or unpleasant listening conditions which might lead you to
believe a problem exists with your radio.
The following conditions are normal and
do not indicate radio trouble:
I
nf
or
mat
i
onPr
ovi
dedby:
Features of your vehicle
Using a cellular phone or a two-way
radio
When a cellular phone is used inside the
vehicle, noise may be produced from the
audio system. This does not mean that
something is wrong with the audio equipment. In such a case, use the cellular
phone at a place as far as possible from
the audio equipment.
CAUTION
JBM004
JBM005
• Fading - As your vehicle moves away
from the radio station, the signal will
weaken and sound will begin to fade.
When this occurs, we suggest that you
select another stronger station.
• Flutter/Static - Weak FM signals or
large obstructions between the transmitter and your radio can disturb the
signal causing static or fluttering noises to occur. Reducing the treble level
may lessen this effect until the disturbance clears.
• Station Swapping - As an FM signal
weakens, another more powerful signal near the same frequency may
begin to play. This is because your
radio is designed to lock onto the clearest signal. If this occurs, select another
station with a stronger signal.
• Multi-Path Cancellation - Radio signals
being received from several directions
can cause distortion or fluttering. This
can be caused by a direct and reflected signal from the same station, or by
signals from two stations with close
frequencies. If this occurs, select
another station until the condition has
passed.
I
nf
or
mat
i
onPr
ovi
dedby:
When using a communication system such as a cellular phone or a
radio set inside the vehicle, a separate external antenna must be fitted.
When a cellular phone or a radio set
is used with an internal antenna
alone, it may interfere with the vehicle's electrical system and adversely
affect safe operation of the vehicle.
WARNING
Do not use a cellular phone while
driving. Stop at a safe location to
use a cellular phone.
4 97
Features of your vehicle
Caring for disc
• If the temperature inside the car is too
high, open the car windows to ventilate
before using the system.
• It is illegal to copy and use MP3/WMA
files without permission. Use CDs that
are created only by lawful means.
• Do not apply volatile agents, such as
benzene and thinner, normal cleaners
and magnetic sprays made for analogue disc onto CDs.
• To prevent the disc surface from getting damaged, hold CDs by the edges
or the center hole only.
• Clean the disc surface with a piece of
soft cloth before playback (wipe it from
the center to the outside edge).
• Do not damage the disc surface or
attach pieces of sticky tape or paper.
• Make certain only CDs are inserted
into the CD player (Do not insert more
than one CD at a time).
• Keep CDs in their cases after use to
protect them from scratches or dirt.
• Depending on the type of CD-R/CDRW CDs, certain CDs may not operate
normally according to the manufacturing companies. In such circumstances,
continued use may cause malfunctions
to your audio system.
4 98
✽ NOTICE
- Playing an Incompatible Copy
Protected Audio CD
Some copy protected CDs, which do not
comply with international audio CD
standards (Red Book), may not play on
your car audio. Please note that inabilities to properly play a copy protected
CD may indicate that the CD is defective, not the CD player.
I
nf
or
mat
i
onPr
ovi
dedby:
NOTE:
Order of playing files (folders) :
1. Song playing order : to sequentially.
2. Folder playing order :
❋ If no song file is contained in the folder, that folder is not displayed.
Features of your vehicle
WARNING
• Do not stare at the screen while
driving. Staring at the screen for
prolonged periods of time could
lead to traffic accidents.
• Do not disassemble, assemble, or
modify the audio system. Such
acts could result in accidents,
fire, or electric shock.
• Using the phone while driving
may lead to a lack of attention of
traffic conditions and increase
the likelihood of accidents.
Use the phone feature after parking the vehicle.
• Heed caution not to spill water or
introduce foreign objects into the
device. Such acts could lead to
smoke, fire, or product malfunction.
(Continued)
I
nf
or
mat
i
onPr
ovi
dedby:
(Continued)
• Please refrain from use if the
screen is blank or no sound can
be heard as these signs may indicate product malfunction.
Continued use in such conditions
could lead to accidents(fires,
electric shock) or product malfunctions.
• Do not touch the antenna during
thunder or lightening as such
acts may lead to lightning
induced electric shock.
• Do not stop or park in parkingrestricted areas to operate the
product. Such acts could lead to
traffic accidents.
• Use the system with the vehicle
ignition turned on. Prolonged use
with the ignition turned off could
result in battery discharge.
4 99
Features of your vehicle
CAUTION
• Operating the device while driving
could lead to accidents due to a
lack of attention to external surroundings. First park the vehicle
before operating the device.
• Adjust the volume to levels that
allow the driver to hear sounds
from outside of the vehicle. Driving
in a state where external sounds
cannot be heard may lead to accidents.
• Pay attention to the volume setting
when turning the device on. A sudden output of extreme volume
upon turning the device on could
lead to hearing impairment.
(Adjust the volume to a suitable
levels before turning off the
device.)
(Continued)
4 100
(Continued)
• Turn on the car ignition before
using this device. Do not operate
the audio system for long periods
of time with the ignition turned off
as such operations may lead to
battery discharge.
• Do not subject the device to
severe shock or impact. Direct
pressure onto the front side of
the monitor may cause damage to
the LCD or touch screen.
• When cleaning the device, make
sure to turn off the device and
use a dry and smooth cloth.
Never use tough materials, chemical cloths, or solvents (alcohol,
benzene, thinners, etc.) as such
materials may damage the device
panel or cause color/quality deterioration.
(Continued)
I
nf
or
mat
i
onPr
ovi
dedby:
(Continued)
• Do not place beverages close to
the audio system. Spilling beverages may lead to system malfunction.
• In case of product malfunction,
please contact your place of purchase or After Service center.
• Placing the audio system within
an electromagnetic environment
may result in noise interference.
• Prevent caustic solutions such as
perfume and cosmetic oil from
contacting
the
dashboard
because they may cause damage
or discoloration.
Features of your vehicle
✽ NOTICE
- USING THE USB DEVICE
• To use an external USB device, make
sure the device is not connected
when starting up the vehicle.
Connect the device after starting up.
• If you start the engine when the
USB device is connected, it may
damage the USB device. (USB
flashdrives are very sensitive to
electric shock.)
• If the engine is started up or turned
off while the external USB device is
connected, the external USB device
may not work.
• The System may not play unauthenticated MP3 or WMA files.
1) It can only play MP3 files with
the compression rate between
8Kbps~320Kbps.
2) It can only play WMA music
files with the compression rate
between 8Kbps~320Kbps.
• Take precautions for static electricity when connecting or disconnecting the external USB device.
(Continued)
(Continued)
• An encrypted MP3 PLAYER is not
recognizable.
• Depending on the condition of the
external USB device, the connected
external USB device can be unrecognizable.
• When the formatted byte/sector
setting of External USB device is
not either 512BYTE or 2048BYTE,
then the device will not be recognized.
• Use only a USB device formatted to
FAT 12/16/32.
• USB devices without USB I/F
authentication may not be recognizable.
• Make sure the USB connection terminal does not come in contact with
the human body or other objects.
• If you repeatedly connect or disconnect the USB device in a short period of time, it may break the device.
• You may hear a strange noise when
connecting or disconnecting a USB
device.
(Continued)
I
nf
or
mat
i
onPr
ovi
dedby:
(Continued)
• If you disconnect the external USB
device during playback in USB
mode, the external USB device can
be damaged or may malfunction.
Therefore, disconnect the external
USB device when the audio is
turned off or in another mode. (e.g,
Radio, CD)
• Depending on the type and capacity
of the external USB device or the
type of the files stored in the device,
there is a difference in the time
taken for recognition of the device.
• Do not use the USB device for purposes other than playing music
files.
• Playing videos through the USB is
not supported.
• Use of USB accessories such as
rechargers or heaters using USB
I/F may lower performance or
cause trouble.
(Continued)
4 101
Features of your vehicle
(Continued)
• If you use devices such as a USB hub
purchased separately, the vehicle’s
audio system may not recognize the
USB device. In that case, connect the
USB device directly to the multimedia
terminal of the vehicle.
• If the USB device is divided by logical
drives, only the music files on the
highest-priority drive are recognized
by car audio.
• Devices such as MP3 Player/ Cellular
phone/Digital camera can be unrecognizable by standard USB I/F can be
unrecognizable.
• Charging through the USB may not
be supported in some mobile devices.
• USB HDD or USB types liable to connection failures due to vehicle vibrations are not supported.
(i-stick type)
• Some non-standard USB devices
(METAL COVER TYPE USB) can be
unrecognizable.
(Continued)
4 102
(Continued)
• Some USB flash memory readers
(such as CF, SD, micro SD, etc.) or
external-HDD type devices can be
unrecognizable.
• Music files protected by DRM
(DIGITAL RIGHTS MANAGEMENT) are not recognizable.
• The data in the USB memory may
be lost while using this audio.
Always back up important data on
a personal storage device.
• Please avoid using USB
memory products which
can be used as key
chains or cellular phone
accessories as they could
cause damage to the USB jack.
Please make certain only to use
plug type connector products.
I
nf
or
mat
i
onPr
ovi
dedby:
Features of your vehicle
✽ NOTICE - USING THE
iPod® DEVICE
• Some iPod® models may not support communication protocol and
files may not properly play.
Supported iPod® models:
- iPhone® 3GS/4
- iPod® touch 1st~4th generation
- iPod® nano 1st~6th generation
- iPod® classic
• The order of search or playback of
songs in the iPod® can be different
from the order searched in the
audio system.
• If the iPod® is disabled due to its
own malfunction, reset the iPod®.
(Reset: Refer to iPod® manual)
• An iPod® may not operate normally on low battery.
(Continued)
(Continued)
• Some iPod® devices, such as the
iPhone® , can be connected through
the Bluetooth® Wireless Technology
interface. The device must have
Wireless
audio
Bluetooth®
Technology capability (such as for
stereo headphone Bluetooth®
Wireless Technology).
The device can play, but it will not
be controlled by the audio system.
• To use iPod® features within the
audio, use the cable provided upon
purchasing an iPod® device.
• Skipping or improper operation
may occur depending on the characteristics of your iPod®/ iPhone®
device.
• If your iPhone® is connected to
both the Bluetooth® Wireless
Technology and USB, the sound
may not be properly played. In
your iPhone®, select the Dock connector or Bluetooth® Wireless
Technology to change the sound
output (source).
(Continued)
I
nf
or
mat
i
onPr
ovi
dedby:
(Continued)
• When connecting iPod® with the
iPod® Power Cable, insert the connector to the multimedia socket
completely. If not inserted completely, communications between
iPod® and audio may be interrupted.
• When adjusting the sound effects of
the iPod® and the audio system, the
sound effects of both devices will
overlap and might reduce or distort
the quality of the sound.
• Deactivate (turn off) the equalizer
function of an iPod® when adjusting the audio system’s volume, and
turn off the equalizer of the audio
system when using the equalizer of
an iPod®.
• When not using iPod® with car
audio, detach the iPod® cable from
iPod®. Otherwise, iPod® may
remain in accessory mode, and may
not work properly.
4 103
Features of your vehicle
✽ NOTICE - Bluetooth®
Wireless Technology
✽ NOTICE - BEFORE USING
THE Bluetooth® HANDSFREE
✽ NOTICE - PRECAUTIONS
FOR SAFE DRIVING
• The Bluetooth® word mark and logos
are registered trademarks owned by
Bluetooth SIG, lnc. and any use of
such marks is under license.
A Bluetooth® enabled call phone is
required to use Bluetooth® wireless
technology.
• Bluetooth® Wirelss Technology phone
compatibility can be checked by visiting www. hyundaiusa.com and under
the SERVICE & PARTS BLUETOOTH COMPATIBILITY
menu.
What is Bluetooth® ?
• Bluetooth® Handsfree is a feature that
enables drivers to practice safe driving. Connecting the head unit with a
Bluetooth® phone allows the user to
conveniently make and receive calls
and use contacts. Before using
Bluetooth® , carefully read the contents
of this user’s manual.
• Excessive use or operations while
driving may lead to negligent driving
practices and result in accidents.
Refrain from excessive operations
while driving.
• Viewing the screen for prolonged periods of time is dangerous and may lead
to accidents. When driving, view the
screen only for short periods of time.
4 104
• Bluetooth® refers to a short-distance
wireless networking technology which
uses a 2.4GHz ~ 2.48GHz frequency to
connect various devices within a certain distance.
• Supported within PCs, external
devices, Bluetooth® phones, PDAs,
various electronic devices, and automotive environments, Bluetooth®
allows data to be transmitted at high
speeds without having to use a connector cable.
• Bluetooth® Handsfree refers to a device
which allows the user to conveniently
make phone calls with Bluetooth®
mobile phones through the audio system.
• Bluetooth® Handsfree may not be supported in some mobile phones. To learn
more about mobile device compatibility,
visit www. hyundaiusa.com.
I
nf
or
mat
i
onPr
ovi
dedby:
Features of your vehicle
✽ NOTICE - WHEN CONNECTING A Bluetooth® PHONE
• Before connecting the head unit with
the mobile phone, check to see that the
mobile phone supports Bluetooth®
features.
• Even if the phone supports
Bluetooth®, the phone will not be
found during device searches if the
phone has been set to hidden state or
the Bluetooth® power is turned off.
Disable the hidden state or turn on the
power
prior
to
Bluetooth®
searching/connecting with the Head
unit.
• Bluetooth phone is automatically connected when the ignition on.
• If you do not want automatic connection with your Bluetooth® device, turn
off the Bluetooth® feature within your
mobile phone.
• The Handsfree call volume and quality
may differ depending on the mobile
phone.
(Continued)
(Continued)
• Park the vehicle when connecting the
head unit with the mobile phone.
• Bluetooth® connection may become
intermittently disconnected in some
mobile phones. Follow these steps to
try again.
1. Within the mobile phone, turn the
Bluetooth® function off/on and try
again.
2. Turn the mobile phone power
Off/On and try again.
3. Completely remove the mobile
phone battery, reboot, and then
again.
4. Reboot the Audio System and try
again.
5. Delete all paired devices, pair and
try again.
• Handsfree call quality and volume
may differ depending on the model of
your mobile phone.
I
nf
or
mat
i
onPr
ovi
dedby:
4 105
Features of your vehicle
✽ NOTICE - USING THE Voice
Recognition
• When using the voice recognition feature, only commands listed within the
user's manual are supported.
• Be aware that during the operation of
the voice recognition system, pressing
any key other than the
key terminate voice recognition mode.
• For superior voice recognition performance, position the microphone
used for voice recognition above the
head of the driver’s seat and maintain
a proper position when saying commands.
• Within the following situations, voice
recognition may not function properly
due to external sound.
- When the windows and sunroof are
open
- When the wind of the cooling / heating device is strong
- When entering and passing through
tunnels
(Continued)
4 106
(Continued)
- When driving on rugged and
uneven roads
- During severe rain (heavy rains,
windstorms)
• Phone related voice commands can be
used only when a Bluetooth® Wireless
Technology device is connected.
• When making calls by stating a name,
the corresponding contact must be
downloaded and stored within the
audio system.
• After downloading the Bluetooth®
Wireless Technology phone book, it
takes some times to convert the phone
book data into voice information.
During this time, voice recognition
may not properly operate.
• Pronounce the voice commands naturally and clearly as if in a normal conversation.
I
nf
or
mat
i
onPr
ovi
dedby:
Features of your vehicle
■ CD Player : AC180SBAN,AC180SBKN,AC1B0SBAN,AC1B0SBKN
❋No
logo will be shown if the Bluetooth® Wireless Technology feature is not supported.
I
nf
or
mat
i
onPr
ovi
dedby:
4 107
Features of your vehicle
SYSTEM CONTROLLERS AND
FUNCTIONS
Audio Head Unit
(for Bluetooth® equipped model)
1.
(EJECT)
• Ejects the disc.
4 108
2. RADIO
• Changes to FM, AM, XM mode.
• Each time the key is pressed, the
mode is changed in order of FM1,
FM2, AM, XM1, XM2, XM3.
❈ In Setup>Display, the radio pop up
screen will be displayed when [Mode
Pop up] is turned On .
When the pop up screen is displayed,
use the
TUNE knob or keys 1
~ 6 to select the desired mode.
3. MEDIA
• Changes to CD, USB(iPod®), AUX, My
Music, BT Audio mode.
• Each time the key is pressed, the
mode is changed in order of CD,
USB(iPod®), AUX, My Music, BT
Audio.
❈ In Setup>Display, the media pop up
screen will be displayed when [Mode
Pop up] is turned On . When the
pop up screen is displayed, use the
TUNE knob or keys 1 ~ 6 to
select the desired mode.
I
nf
or
mat
i
onPr
ovi
dedby:
4. PHONE (for Bluetooth® Wireless
Technology equipped model)
• Operates Phone Screen
❈ When a phone is not connected, the
connection screen is displayed.
SEEK
5. TRACK
• Radio Mode : Automatically searches
for broadcast frequencies.
• CD, USB, iPod®, My Music modes
- Shortly press the key (under 0.8 seconds): Moves to next or previous
song (file)
- Press and hold the key (over 0.8 seconds): Rewinds or fast-forwards the
current song.
• BT Audio mode : Moves to next or previous song(file)
❈ The Play/Pause feature may operate
differently depending on the mobile
phone.
6. PWR/VOL knob
•
Power : Turns power On/Off by
pressing the knob
•
Volume : Sets volume by turning
the knob left/right
Features of your vehicle
❈ Press the SCAN key again to continue listening to the current frequency.
❈ SiriusXM™ Radio: does not support
the Preset scan feature.
• CD, USB, My Music mode
- Shortly press the key (under 0.8 seconds): Previews each song (file) for 10
seconds each.
❈ Press the SCAN key again to continue listening to the current song (file).
SETUP
7. DISP
• Each time the button is shortly pressed
(under 0.8 seconds), it sets the screen
Off ➟ Screen On ➟ Screen Off
❈ Audio operation is maintained and only
the screen will be turned Off. In the
screen Off state, press any key to turn
the screen On again.
8. SCAN
• Radio Mode
- Shortly press the key (under 0.8 seconds): Previews each broadcast for 5
seconds each.
- Press and hold the key (over 0.8 seconds): Previews the broadcasts saved
in Preset 1 ~ 6
for 5 seconds
each.
9. CLOCK
• Shortly press the key (under 0.8 seconds) : Moves to the Display, Sound,
Clock, Phone, System setting modes.
• Press and hold the key (over 0.8 seconds): Moves to the Clock setting
mode.
10. MENU
• Displays menus for the current mode.
12.
TUNE knob
• Radio mode : Changes frequency by
turning the knob left/right.
• CD, USB, iPod®, My Music mode:
Searches songs (files) by turning the
knob left/right.
❈ When the desired song is displayed,
press the knob to play the song.
• Moves focus in all selection menus and
selects menus.
1 ~ 6 (Preset)
13.
• Radio Mode: Saves frequencies (channels) or receives saved frequencies
(channels)
• CD, USB, iPod®, My Music mode
- 1 RPT : Repeat
- 2 RDM : Random
• In the Radio, Media, Setup, and Menu
pop up screen, the number menu is
selected.
CAT
11. FOLDER
• Radio Mode
- SiriusXM™ RADIO : Category Search
• MP3, CD, USB mode : Folder Search
I
nf
or
mat
i
onPr
ovi
dedby:
4 109
Features of your vehicle
Audio Head Unit
15. SAT
• Changes to XM mode.
14. FM/AM
• Changes to FM mode.
• Each time the key is pressed, the
mode changed in order of FM1, FM2,
AM.
4 110
I
nf
or
mat
i
onPr
ovi
dedby:
Features of your vehicle
SETUP
Display Settings
Press the SETUP key Select [Display]
Select menu through
TUNE knob
Mode Pop up
[Mode Pop up] Changes On / Off
selection mode
• During On state, press the RADIO or
MEDIA key to display the mode
change pop up screen.
Sound Settings
Press the SETUP key Select [Sound]
Select menu through
TUNE knob
Text Scroll
[Text Scroll] Set On / Off
• On : Maintains scroll
• Off : Scrolls only one (1) time.
Media Display
When playing an MP3 file, select the
desired display info from ‘Folder/File’ or
‘Album/Artist/Song’.
I
nf
or
mat
i
onPr
ovi
dedby:
4 111
Features of your vehicle
Sound Settings
Speed Dependent Volume Control
Voice Recognition Volume
This menu allows you to set the ‘Bass,
Middle, Treble’ and the Sound Fader and
Balance.
Select [Sound Settings] Select menu
through
TUNE knob Turn
TUNE
knob left/right to set
• Bass, Middle, Treble : Selects the sound
tone.
• Fader, Balance : Moves the sound fader
and balance.
• Default : Restores default settings.
❈ Back : While adjusting values, repressing the
TUNE knob will
restore the parent menu.
This feature is used to automatically control the volume level according to the
speed of the vehicle.
Select [Speed Dependent Vol.] Set in 4
levels [Off/Low/Mid/High] of
TUNE
knob
Adjusts voice recognition volume.
Select [Voice Recognition Vol.] Set volume of
TUNE knob
4 112
I
nf
or
mat
i
onPr
ovi
dedby:
Features of your vehicle
CLOCK SETTINGS
CLOCK
Press the SETUP
key Select [Clock]
3
through
TUNE knob or
key
Select menu through
TUNE knob
Clock Settings
This menu is used to set the time.
Select [Clock Settings] Set through
TUNE knob Press
TUNE knob
❈ Adjust the number currently in focus to
make the settings and press the tune
knob to move to the next setting. (Set
in order of Year/Month/Day)
Time Format
This function is used to set the 12/24
hour time format of the audio system.
Select [Time Format] Set 12Hr / 24Hr
through
TUNE knob
❈ Adjust the number currently in focus to
set the [hour] and press the tune knob
to set the [minute].
Clock Display when Power is OFF
Select [Clock Disp.(Pwr Off) Set
/ Off through
TUNE knob
On
Calendar Settings
This menu is used to set the date
(MM/DD/YYYY).
Select [Calendar Settings] Set through
TUNE knob Press
TUNE knob
I
nf
or
mat
i
onPr
ovi
dedby:
On
Off
: Displays time/date on screen
: Turn off.
4 113
Features of your vehicle
SYSTEM SETTINGS
Press the SETUP key Select [System]
Select menu through
TUNE knob
Memory Information
Language
Displays currently used memory and
total system memory.
Select [Memory Information] OK
The currently used memory is displayed
on the left side while the total system
memory is displayed on the right side.
This menu is used to set the display and
voice recognition language.
Select [Language]
Set through
TUNE knob
Prompt Feedback
This feature is used to change voice
command feedback between Normal and
Expert modes.
Select [Prompt Feedback] Set through
TUNE knob
• Normal(On) : This mode is for beginner
users and provides detailed instructions during voice command operation.
• Expert(Off) : This mode is for expert
users and omits some information during voice command operation. (When
using Expert mode, guidance instructions can be heard through the [Help]
or [Menu] commands.
4 114
I
nf
or
mat
i
onPr
ovi
dedby:
❈ The system will reboot after the language is changed.
❈ Language support by region
- English, Francais, Espanol
Features of your vehicle
RADIO : FM, AM OR
SIRIUSXMTM
Preset SEEK
SCAN
Press the 1 ~ 6 key
• Shortly pressing the key (under 0.8
seconds): Plays the frequency saved in
the corresponding key.
• Pressing and holding the key (over 0.8
seconds): Pressing and holding the
1
6
desired key from
~
will
save the currently playing broadcast to
the selected key and sound a BEEP.
Press the SCAN key
• Shortly pressing the key : The broadcast frequency increases and previews
each broadcast for 5 seconds each.
After scanning all frequencies, returns
and plays the current broadcast frequency.
• Pressing and holding the key (over 0.8
seconds): Previews the broadcasts
1
6
saved in Preset
~
for 5
seconds each.
SEEK
SEEK
Press the TRACK key
• Shortly pressing the key (under 0.8
seconds): Changes the frequency.
• Pressing and holding the key (over 0.8
seconds): Automatically searches for
the next frequency.
Selecting through manual search
Turn the
TUNE knob left/right to adjust
the frequency.
• FM : Changes by 200KHz
• AM : Changes by 10KHz
I
nf
or
mat
i
onPr
ovi
dedby:
4 115
Features of your vehicle
MENU
Within MENU key are the A.Store (Auto
Store) and Info functions.
A.Store
Press the MENU key Set [A.Store]
through
TUNE knob or 1 key.
Saves broadcasts with superior reception to 1 ~ 6 keys. If no frequencies are received, then the most recently
received frequency will be broadcast.
4 116
I
nf
or
mat
i
onPr
ovi
dedby:
Features of your vehicle
SiriusXMTM Satellite Radio information
Satellite Radio channels:
SiriusXMTM Satellite Radio offers 150+
channels with 100% commercial-free
music, plus sports, news, talk and entertainment, available nationwide in your
vehicle. For more information and a complete list of SiriusXMTM Satellite Radio
channels, visit www.siriusxm.com in the
United States, sirius-canada.ca in
Canada, or call SiriusXMTM at 1-800-6432112.
Satellite Radio reception factors:
To receive the satellite signal, your vehicle has been equipped with a satellite
radio antenna located on the roof of your
vehicle. The vehicle roof provides the
best location for an unobstructed, open
view of the sky, a requirement of a satellite radio system. Like AM/FM, there are
several factors that can affect satellite
radio reception performance:
• Antenna obstructions: For optimal
reception performance, keep the
antenna clear of snow and ice build-up
and keep luggage and other material
as far away from the antenna as possible.
• Terrain: Hills, mountains, tall buildings,
bridges, tunnels, freeway overpasses,
parking garages, dense tree foliage
and thunderstorms can interfere with
your reception.
SiriusXMTM Satellite Radio service:
SiriusXMTM Satellite Radio is a subscription-based satellite radio service that
broadcasts music, sports, news and
entertainment programming to radio
receivers, which are available for installation in motor vehicles or factory installed,
as well as for the home, portable and
wireless devices, and through an Internet
connection on personal computer.
Vehicles that are equipped with a factory
installed SiriusXMTM Satellite Radio system include:
• Hardware and an introductory trial subscription term, which begins on the
date of sale or lease of the vehicle.
• For a small upgrade fee, access to
SiriusXMTM music channels, and other
select channels over the Internet using
any computer connected to the
Internet (U.S. customers only).
For information on extended subscription terms, contact SiriusXMTM at 1866-635-2349.
I
nf
or
mat
i
onPr
ovi
dedby:
NOTE:
All SiriusXMTM services require a subscription, sold separately or as a
package, after 3-month trial included
with vehicle purchase or lease. If you
decide to continue your SiriusXMTM
service at the end of your trial subscription, the plan you choose will
automatically renew and bill at thencurrent rates until you call us at 1-866635-2349 to cancel. See our Customer
Agreement for complete terms at
www.siriusxm.com. Other fees and
taxes apply. All fees and programming are subject to change. Sirius
satellite service is available only to
those at least 18 and older in the 48
contiguous USA, D.C., and PR (with
coverage limitations). Our Internet
radio service is available throughout
our satellite service area and in AK
and HI. Certain channels are not available on our Internet radio service or
on mobile devices.
© 2013 Sirius XM Radio Inc. Sirius, XM
and all related marks and logos are
trademarks of SiriusXMTM Radio Inc.
All rights reserved
4 117
Features of your vehicle
SiriusXMTM
RADIO
Using SiriusXMTM Satellite
Radio
Your vehicle is equipped with a 3 month
complimentary period of SiriusXMTM
Satellite Radio. XM provides access to
over 130 channels of music, information,
and entertainment programming.
SCAN
Press the SCAN key
• Shortly pressing the key: Previews
each broadcast for 5 seconds each
❈ Press the SCAN key again to continue listening to the current frequency
❈ If the “Category” icon is displayed,
channels are changed within the current category.
Category
CAT
FOLDER
Press the
the
TUNE knob
key Set through
Preset
Press the 1 ~ 6 key
• Shortly pressing the key: Plays the frequency saved in the corresponding
key.
• Pressing and holding the key (over 0.8
seconds): Pressing and holding the
1
6
desired key from
~
will
save the current broadcast to the
selected key and sound a BEEP.
SEEK
SEEK
Press the TRACK key
• Shortly pressing the key: select previous or next channel.
• Pressing and holding the key (over 0.8
seconds): continuously move to previous or next channel.
❈ If the “Category” icon is displayed,
channels are changed within the current category.
4 118
• The display will indicate the category
menus, highlight the category that the
current channel belongs to.
• In the Category List Mode, press the
CAT
key to navigate category
FOLDER
list.
• Press the tune knob to select the lowest channel in the highlighted category.
❈ If channel is selected by selecting category, then the “CATEGORY” icon is
displayed at the top of the screen.
I
nf
or
mat
i
onPr
ovi
dedby:
Features of your vehicle
Tune
• Rotate
TUNE knob : Changes the
channel number or scrolls category list.
• Press
TUNE knob : Selects the
menu.
Menu
Select category menu through the
TUNE knob Press the MENU key
Select [ Info] through the
TUNE knob
or 1 key
Info (Information)
Displays the Artist/Song info of the current song.
I
nf
or
mat
i
onPr
ovi
dedby:
4 119
Features of your vehicle
BASIC METHOD OF USE :
AUDIO CD / MP3 CD / USB /
iPOD® / MY MUSIC
Repeat
Press the MEDIA key to change the
mode in order of CD➟USB(iPod®)➟AUX
➟My Music➟BT Audio.
The folder/file name is displayed on the
screen.
While song (file) is playing 1 RPT (RPT)
key
Audio CD, MP3 CD, USB, iPod®, My
Music mode: RPT on screen
• To repeat one song (press the key :
Repeats the current song.
MP3 CD, USB mode: FLD.RPT on
screen
• To repeat folder (pressing twice):
repeats all files within the current folder.
❈ Press the 1 RPT key again to turn off
repeat.