USB3290 Small Footprint Hi Speed USB 2.0 Device PHY With UTMI Interface Data Sheet SMSC 3290 468143

User Manual: USB3290

Open the PDF directly: View PDF PDF.
Page Count: 47

SMSC USB3290 DATASHEET Revision 1.5 (11-02-07)
Datasheet
PRODUCT FEATURES
USB3290
Small Footprint Hi-Speed
USB 2.0 Device PHY with
UTMI Interface
Available in a 40 ball lead-free RoHS compliant
(4 x 4 x 0.9mm) VFBGA package
Interface compliant with the UTMI specification
(60MHz, 8-bit bidirectional interface)
Only one required power supply (+3.3V)
Supports 480Mbps Hi-Speed (HS) and 12Mbps Full
Speed (FS) serial data transmission rates
Integrated 45Ω and 1.5kΩ termination resistors
reduce external component count
Internal short circuit protection of DP and DM lines
On-chip oscillator operates with low cost 24MHz
crystal
Latch-up performance exceeds 150mA per EIA/JESD
78, Class II
ESD protection levels of 5kV HBM without external
protection devices
SYNC and EOP generation on transmit packets and
detection on receive packets
NRZI encoding and decoding
Bit stuffing and unstuffing with error detection
Supports the USB suspend state, HS detection, HS
Chirp, Reset and Resume
Support for all test modes defined in the USB 2.0
specification
55mA Unconfigured Current (typical) - ideal for bus
powered applications.
83uA suspend current (typical) - ideal for battery
powered applications.
Industrial Operating Temperature -40oC to +85oC
Applications
The USB3290 is the ideal companion to any ASIC, SoC
or FPGA solution designed with a UTMI Hi-Speed USB
device (peripheral) core.
The USB3290 is well suited for:
Cell Phones
MP3 Players
Scanners
External Hard Drives
Digital Still and Video Cameras
Portable Media Players
Entertainment Devices
Printers
ORDER NUMBER(S):
USB3290-FH FOR 40 BALL, VFBGA LEAD-FREE ROHS COMPLIANT PACKAGE
USB3290-FH-TR FOR 40 BALL, VFBGA LEAD-FREE ROHS COMPLIANT PACKAGE (TAPE AND REEL)
Reel Size is 4000 pieces.
Small Footprint Hi-Speed USB 2.0 Device PHY with UTMI Interface
Datasheet
Revision 1.5 (11-02-07) 2 SMSC USB3290
DATASHEET
80 ARKAY DRIVE, HAUPPAUGE, NY 11788 (631) 435-6000, FAX (631) 273-3123
Copyright © 2007 SMSC or its subsidiaries. All rights reserved.
Circuit diagrams and other information relating to SMSC products are included as a means of illustrating typical applications. Consequently, complete information sufficient for
construction purposes is not necessarily given. Although the information has been checked and is believed to be accurate, no responsibility is assumed for inaccuracies. SMSC
reserves the right to make changes to specifications and product descriptions at any time without notice. Contact your local SMSC sales office to obtain the latest specifications
before placing your product order. The provision of this information does not convey to the purchaser of the described semiconductor devices any licenses under any patent
rights or other intellectual property rights of SMSC or others. All sales are expressly conditional on your agreement to the terms and conditions of the most recently dated
version of SMSC's standard Terms of Sale Agreement dated before the date of your order (the "Terms of Sale Agreement"). The product may contain design defects or errors
known as anomalies which may cause the product's functions to deviate from published specifications. Anomaly sheets are available upon request. SMSC products are not
designed, intended, authorized or warranted for use in any life support or other application where product failure could cause or contribute to personal injury or severe property
damage. Any and all such uses without prior written approval of an Officer of SMSC and further testing and/or modification will be fully at the risk of the customer. Copies of
this document or other SMSC literature, as well as the Terms of Sale Agreement, may be obtained by visiting SMSC’s website at http://www.smsc.com. SMSC is a registered
trademark of Standard Microsystems Corporation (“SMSC”). Product names and company names are the trademarks of their respective holders.
SMSC DISCLAIMS AND EXCLUDES ANY AND ALL WARRANTIES, INCLUDING WITHOUT LIMITATION ANY AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE, TITLE, AND AGAINST INFRINGEMENT AND THE LIKE, AND ANY AND ALL WARRANTIES ARISING FROM ANY COURSE
OF DEALING OR USAGE OF TRADE. IN NO EVENT SHALL SMSC BE LIABLE FOR ANY DIRECT, INCIDENTAL, INDIRECT, SPECIAL, PUNITIVE, OR CONSEQUENTIAL
DAMAGES; OR FOR LOST DATA, PROFITS, SAVINGS OR REVENUES OF ANY KIND; REGARDLESS OF THE FORM OF ACTION, WHETHER BASED ON CONTRACT;
TORT; NEGLIGENCE OF SMSC OR OTHERS; STRICT LIABILITY; BREACH OF WARRANTY; OR OTHERWISE; WHETHER OR NOT ANY REMEDY OF BUYER IS HELD
TO HAVE FAILED OF ITS ESSENTIAL PURPOSE, AND WHETHER OR NOT SMSC HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Small Footprint Hi-Speed USB 2.0 Device PHY with UTMI Interface
Datasheet
SMSC USB3290 3 Revision 1.5 (11-02-07)
DATASHEET
Table of Contents
Chapter 1 General Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.1 Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Chapter 2 Functional Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Chapter 3 Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Chapter 4 Interface Signal Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Chapter 5 Limiting Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Chapter 6 Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
6.1 Driver Characteristics of Full-Speed Drivers in High-Speed Capable Transceivers. . . . . . . . . . . . 16
6.2 High-speed Signaling Eye Patterns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Chapter 7 Functional Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
7.1 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
7.2 System Clocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
7.3 Clock and Data Recovery Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
7.4 TX Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
7.5 RX Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
7.6 USB 2.0 Transceiver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
7.6.1 High Speed and Full Speed Transceivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
7.6.2 Termination Resistors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
7.6.3 Bias Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
7.7 Crystal Oscillator and PLL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
7.8 Internal Regulators and POR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
7.8.1 Internal Regulators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
7.8.2 Power On Reset (POR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
7.8.3 Reset Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Chapter 8 Application Notes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
8.1 Linestate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
8.2 OPMODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
8.3 Test Mode Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
8.4 SE0 Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
8.5 Reset Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
8.6 Suspend Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
8.7 HS Detection Handshake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
8.8 HS Detection Handshake – FS Downstream Facing Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
8.9 HS Detection Handshake – HS Downstream Facing Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
8.10 HS Detection Handshake – Suspend Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
8.11 Assertion of Resume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
8.12 Detection of Resume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
8.13 HS Device Attach . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
8.14 Application Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Chapter 9 Package Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Small Footprint Hi-Speed USB 2.0 Device PHY with UTMI Interface
Datasheet
Revision 1.5 (11-02-07) 4 SMSC USB3290
DATASHEET
List of Figures
Figure 2.1 USB3290 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Figure 3.1 USB3290 Pinout - Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Figure 6.1 Full-Speed Driver VOH/IOH Characteristics for High-speed Capable Transceiver . . . . . . . . 17
Figure 6.2 Full-Speed Driver VOL/IOL Characteristics for High-speed Capable Transceiver. . . . . . . . . 17
Figure 6.3 Eye Pattern Measurement Planes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Figure 6.4 Eye Pattern for Transmit Waveform and Eye Pattern Definition . . . . . . . . . . . . . . . . . . . . . . 19
Figure 6.5 Eye Pattern for Receive Waveform and Eye Pattern Definition. . . . . . . . . . . . . . . . . . . . . . . 20
Figure 7.1 FS CLK Relationship to Transmit Data and Control Signals . . . . . . . . . . . . . . . . . . . . . . . . . 21
Figure 7.2 FS CLK Relationship to Receive Data and Control Signals. . . . . . . . . . . . . . . . . . . . . . . . . . 22
Figure 7.3 Transmit Timing for a Data Packet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Figure 7.4 Receive Timing for Data with Unstuffed Bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Figure 7.5 Receive Timing for a Handshake Packet (no CRC). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Figure 7.6 Receive Timing for Setup Packet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Figure 7.7 Receive Timing for Data Packet (with CRC-16). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Figure 8.1 Reset Timing Behavior (HS Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Figure 8.2 Suspend Timing Behavior (HS Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Figure 8.3 HS Detection Handshake Timing Behavior (FS Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Figure 8.4 Chirp K-J-K-J-K-J Sequence Detection State Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Figure 8.5 HS Detection Handshake Timing Behavior (HS Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Figure 8.6 HS Detection Handshake Timing Behavior from Suspend . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Figure 8.7 Resume Timing Behavior (HS Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Figure 8.8 Device Attach Behavior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Figure 8.9 USB3290 Application Diagram showing USB related signals . . . . . . . . . . . . . . . . . . . . . . . . 41
Figure 8.10 USB3290 Application Diagram showing power and miscellaneous signals. . . . . . . . . . . . . . 42
Figure 9.1 USB3290-FH 40 Ball, VFBGA Package Outline & Parameters 4x4x0.9mm Body, Lead-Free
RoHS Compliant 43
Figure 9.2 BGA, 4x4 Taping Dimensions and Part Orientation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Figure 9.3 Reel Dimensions for 12mm Carrier Tape. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Figure 9.4 Tape Length and Part Quantity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Small Footprint Hi-Speed USB 2.0 Device PHY with UTMI Interface
Datasheet
SMSC USB3290 5 Revision 1.5 (11-02-07)
DATASHEET
List of Tables
Table 4.1 System Interface Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Table 4.2 Data Interface Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Table 4.3 USB I/O Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Table 4.4 Biasing and Clock Oscillator Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Table 4.5 Power and Ground Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Table 5.1 Absolute Maximum Ratings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Table 5.2 Recommended Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Table 5.3 Recommended External Clock Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Table 6.1 Electrical Characteristics: Supply Pins (Note 6.1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Table 6.2 DC Electrical Characteristics: Logic Pins (Note 6.2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Table 6.3 DC Electrical Characteristics: Analog I/O Pins (DP/DM) (Note 6.3) . . . . . . . . . . . . . . . . . . . . 14
Table 6.4 Dynamic Characteristics: Analog I/O Pins (DP/DM) (Note 6.4). . . . . . . . . . . . . . . . . . . . . . . . 15
Table 6.5 Dynamic Characteristics: Digital UTMI Pins (Note 6.5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Table 7.1 DP/DM Termination vs. Signaling Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Table 8.1 Linestate States. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Table 8.2 Operational Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Table 8.3 USB 2.0 Test Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Table 8.4 Reset Timing Values (HS Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Table 8.5 Suspend Timing Values (HS Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Table 8.6 HS Detection Handshake Timing Values (FS Mode). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Table 8.7 Reset Timing Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Table 8.8 HS Detection Handshake Timing Values from Suspend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Table 8.9 Resume Timing Values (HS Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Table 8.10 Attach and Reset Timing Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Small Footprint Hi-Speed USB 2.0 Device PHY with UTMI Interface
Datasheet
Revision 1.5 (11-02-07) 6 SMSC USB3290
DATASHEET
Chapter 1 General Description
The USB3290 provides the Physical Layer (PHY) interface to a USB 2.0 Device Controller. The IC is
available in a 40 ball lead-free RoHS compliant VFBGA package. The small footprint package makes
the USB3290 ideal for portable consumer electronics applications.
1.1 Product Description
The USB3290 is an industrial temperature USB 2.0 physical layer transceiver (PHY) integrated circuit.
SMSC’s proprietary technology results in low power dissipation, which is ideal for building a bus
powered USB 2.0 peripheral. The PHY uses an 8-bit bidirectional parallel interface, which complies
with the USB Transceiver Macrocell Interface (UTMI) specification. It supports 480Mbps transfer rate,
while remaining backward compatible with USB 1.1 legacy protocol at 12Mbps.
All required termination and 5.25V short circuit protection of the DP/DM lines are internal to the chip.
The USB3290 also has an integrated 1.8V regulator so that only a 3.3V supply is required.
While transmitting data, the PHY serializes data and generates SYNC and EOP fields. It also performs
needed bit stuffing and NRZI encoding. Likewise, while receiving data, the PHY de-serializes incoming
data, stripping SYNC and EOP fields and performs bit un-stuffing and NRZI decoding.
Small Footprint Hi-Speed USB 2.0 Device PHY with UTMI Interface
Datasheet
SMSC USB3290 7 Revision 1.5 (11-02-07)
DATASHEET
Chapter 2 Functional Block Diagram
Figure 2.1 USB3290 Block Diagram
PWR
Control
FS SE+
R
X
UTMI
Interface
TX State
Machine
Parallel to
Serial
Conversion
Bit Stuff
NRZI
Encode
TX
LOGIC
Clock
Recovery Unit
Clock
and
Data
Recovery
Elasticity
Buffer
VP
VM
BIASING
Bandgap Voltage Reference
Current Reference
RBIAS
VDD3.3
PLL and
XTAL OSC System
Clocking
FS RX
FS SE-
HS RX
HS SQ
RX State
Machine
Serial to
Parallel
Conversion
Bit Unstuff
NRZI
Decode
RX
LOGIC
DM
TX
1.5kΩ
FS
TX
HS
TX
HS_DATA
HS_CS_ENABLE
HS_DRIVE_ENABLE
OEB
VMO
VPO
RPU_EN
MUX
DP
RXVALID
RXACTIVE
RXERROR
TXREADY
RESET
SUSPENDN
XCVRSELECT
TERMSELECT
OPMODE[1:0]
LINESTATE[1:0]
CLKOUT
TXVALID
DATA[7:0]
XI
XO
1.8V
Regulator
Small Footprint Hi-Speed USB 2.0 Device PHY with UTMI Interface
Datasheet
Revision 1.5 (11-02-07) 8 SMSC USB3290
DATASHEET
Chapter 3 Pinout
Figure 3.1 USB3290 Pinout - Top View
TOP VIEW
TSELTXR
SPDN TXV
RST
V33
V33
DP
XSEL GND
CLK
DM
V33
RXA OM0 LS1
LS0OM1
D6
D7
RXV
D0
D5
D2 D3
D4
D1
RB
VIOV18A
XI XO
V18
V33
RXEREN
G
E
C
B
A
F
D
1765432
GND
GND GND
VIO
Small Footprint Hi-Speed USB 2.0 Device PHY with UTMI Interface
Datasheet
SMSC USB3290 9 Revision 1.5 (11-02-07)
DATASHEET
Chapter 4 Interface Signal Definition
Table 4.1 System Interface Signals
NAME DIRECTION ACTIVE
LEVEL DESCRIPTION
RESET
(RST) Input High Reset. Reset all state machines. After coming out of
reset, must wait 5 rising edges of clock before asserting
TXValid for transmit.
See Section 7.8.3
XCVRSELECT
(XSEL) Input N/A Transceiver Select. This signal selects between the FS
and HS transceivers:
0: HS transceiver enabled
1: FS transceiver enabled.
TERMSELECT
(TSEL) Input N/A Termination Select. This signal selects between the FS
and HS terminations:
0: HS termination enabled
1: FS termination enabled
SUSPENDN
(SPDN) Input Low Suspend. Places the transceiver in a mode that draws
minimal power from supplies. Shuts down all blocks not
necessary for Suspend/Resume operation. While
suspended, TERMSELECT must always be in FS mode
to ensure that the 1.5kΩ pull-up on DP remains powered.
0: Transceiver circuitry drawing suspend current
1: Transceiver circuitry drawing normal current
CLKOUT
(CLK) Output Rising Edge System Clock. This output is used for clocking receive
and transmit parallel data at 60MHz.
OPMODE[1:0]
(OM1)
(OM0)
Input N/A Operational Mode. These signals select between the
various operational modes:
[1] [0] Description
0 0 0: Normal Operation
0 1 1: Non-driving (all terminations removed)
1 0 2: Disable bit stuffing and NRZI encoding
1 1 3: Reserved
LINESTATE[1:0]
(LS1)
(LS0)
Output N/A Line State. These signals reflect the current state of the
USB data bus in FS mode, with [0] reflecting the state of
DP and [1] reflecting the state of DM. When the device is
suspended or resuming from a suspended state, the
signals are combinatorial. Otherwise, the signals are
synchronized to CLKOUT.
[1] [0] Description
0 0 0: SE0
0 1 1: J State
1 0 2: K State
1 1 3: SE1
Small Footprint Hi-Speed USB 2.0 Device PHY with UTMI Interface
Datasheet
Revision 1.5 (11-02-07) 10 SMSC USB3290
DATASHEET
Table 4.2 Data Interface Signals
NAME DIRECTION ACTIVE
LEVEL DESCRIPTION
DATA[7:0]
(D7)
.
.
.
(D0)
Bidirectional High Data bus. 8-bit Bidirectional mode.
TXVALID DATA[7:0]
0 output
1 input
TXVALID
(TXV) Input High Transmit Valid. Indicates that the DATA bus is valid for transmit. The
assertion of TXVALID initiates the transmission of SYNC on the USB
bus. The negation of TXVALID initiates EOP on the USB.
Control inputs (OPMODE[1:0], TERMSELECT,XCVRSELECT) must
not be changed on the de-assertion or assertion of TXVALID. The
PHY must be in a quiescent state when these inputs are changed.
TXREADY
(TXR) Output High Transmit Data Ready. If TXVALID is asserted, the SIE must always
have data available for clocking into the TX Holding Register on the
rising edge of CLKOUT. TXREADY is an acknowledgement to the
SIE that the transceiver has clocked the data from the bus and is
ready for the next transfer on the bus. If TXVALID is negated,
TXREADY can be ignored by the SIE.
RXVALID
(RXV) Output High Receive Data Valid. Indicates that the DATA bus has received valid
data. The Receive Data Holding Register is full and ready to be
unloaded. The SIE is expected to latch the DATA bus on the rising
edge of CLKOUT.
RXACTIVE
(RXA) Output High Receive Active. Indicates that the receive state machine has
detected Start of Packet and is active.
RXERROR
(RXE) Output High Receive Error.
0: Indicates no error.
1: Indicates a receive error has been detected.
This output is clocked with the same timing as the receive DATA lines
and can occur at anytime during a transfer.
Table 4.3 USB I/O Signals
NAME DIRECTION ACTIVE
LEVEL DESCRIPTION
DP I/O N/A USB Positive Data Pin.
DM I/O N/A USB Negative Data Pin.
Table 4.4 Biasing and Clock Oscillator Signals
NAME DIRECTION ACTIVE
LEVEL DESCRIPTION
RBIAS
(RB) Input N/A External 1% bias resistor. Requires a 12kΩ resistor to ground.
Used for setting HS transmit current level and on-chip
termination impedance.
XI/XO Input N/A External crystal. 24MHz crystal connected from XI to XO.
Small Footprint Hi-Speed USB 2.0 Device PHY with UTMI Interface
Datasheet
SMSC USB3290 11 Revision 1.5 (11-02-07)
DATASHEET
Table 4.5 Power and Ground Signals
NAME DIRECTION ACTIVE
LEVEL DESCRIPTION
VDD3.3
(V33)
(VIO)
N/A N/A 3.3V Supply. Provides power for USB 2.0 Transceiver, UTMI+
Digital, Digital I/O, and Regulators.
REG_EN
(REN) Input High On-Chip 1.8V regulator enable. Connect to ground to disable
both of the on chip (VDDA1.8 and VDD1.8) regulators. When
regulators are disabled:
External 1.8V must be supplied to VDDA1.8 and VDD1.8 pins.
When the regulators are disabled, VDDA1.8 may be connected
to VDD1.8 and a bypass capacitor (0.1μF recommended)
should be connected to each pin.
The voltage at VDD3.3 must be at least 2.64V (0.8 * 3.3V)
before voltage is applied to VDDA1.8 and VDD1.8.
VDD1.8
(V18) N/A N/A 1.8V Digital Supply. Supplied by On-Chip Regulator when
REG_EN is active. Low ESR 4.7uF minimum capacitor
requirement when using internal regulators. Do not connect
VDD1.8 to VDDA1.8 when using internal regulators. When the
regulators are disabled, VDD1.8 may be connected to VDD1.8A.
VSS
(GND) N/A N/A Common Ground.
VDDA1.8
(V18A) N/A N/A 1.8V Analog Supply. Supplied by On-Chip Regulator when
REG_EN is active. Low ESR 4.7uF minimum capacitor
requirement when using internal regulators. Do not connect
VDD1.8A to VDD1.8 when using internal regulators. When the
regulators are disabled, VDD1.8A may be connected to VDD1.8.
Small Footprint Hi-Speed USB 2.0 Device PHY with UTMI Interface
Datasheet
Revision 1.5 (11-02-07) 12 SMSC USB3290
DATASHEET
Chapter 5 Limiting Values
Note: In accordance with the Absolute Maximum Rating system (IEC 60134)
Table 5.1 Absolute Maximum Ratings
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
Maximum DP and DM
voltage to Ground VMAX_5V -0.3 5.5 V
Maximum VDD1.8 and
VDDA1.8 voltage to Ground VMAX_1.8V -0.3 2.5 V
Maximum 3.3V Supply
Voltage to Ground VMAX_3.3V -0.3 4.0 V
Maximum I/O Voltage to
Ground VI-0.3 4.0 V
Storage Temperature TSTG -55 150 oC
ESD PERFORMANCE
All Pins VHBM Human Body Model ±5 kV
LATCH-UP PERFORMANCE
All Pins ILTCH_UP EIA/JESD 78, Class II 150 mA
Table 5.2 Recommended Operating Conditions
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
3.3V Supply Voltage
(VDD3.3 and VDDA3.3) VDD3.3 3.0 3.3 3.6 V
Input Voltage on Digital Pins VI0.0 VDD3.3 V
Input Voltage on Analog I/O
Pins (DP, DM) VI(I/O) 0.0 VDD3.3 V
Ambient Temperature TA-40 85 oC
Table 5.3 Recommended External Clock Conditions
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
System Clock Frequency XO driven by the external
clock; and no connection at XI 24
(±100ppm) MHz
System Clock Duty Cycle XO driven by the external
clock; and no connection at XI 45 50 55 %
Small Footprint Hi-Speed USB 2.0 Device PHY with UTMI Interface
Datasheet
SMSC USB3290 13 Revision 1.5 (11-02-07)
DATASHEET
Chapter 6 Electrical Characteristics
Note 6.1 VDD3.3 = 3.0 to 3.6V; VSS = 0V; TA = -40oC to 85oC; unless otherwise specified.
Note 6.2 VDD3.3 = 3.0 to 3.6V; VSS = 0V; TA = -40oC to 85oC; unless otherwise specified.
Table 6.1 Electrical Characteristics: Supply Pins (Note 6.1)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
Unconfigured Current IAVG(UCFG) Device Unconfigured 55 mA
FS Idle Current IAVG(FS) FS idle not data transfer 55 mA
FS Transmit Current IAVG(FSTX) FS current during data
transmit 60.5 mA
FS Receive Current IAVG(FSRX) FS current during data
receive 57.5 mA
HS Idle Current IAVG(HS) HS idle not data transfer 60.6 mA
HS Transmit Current IAVG(HSTX) HS current during data
transmit 62.4 mA
HS Receive Current IAVG(HSRX) HS current during data
receive 61.5 mA
Low Power Mode IDD(LPM) VBUS 15kΩ pull-down and
1.5kΩ pull-up resistor
currents not included.
83 uA
Table 6.2 DC Electrical Characteristics: Logic Pins (Note 6.2)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
Low-Level Input Voltage VIL VSS 0.8 V
High-Level Input Voltage VIH 2.0 VDD3.3 V
Low-Level Output Voltage VOL IOL = 8mA 0.4 V
High-Level Output Voltage VOH IOH = -8mA VDD3.3
- 0.5 V
Input Leakage Current ILI ± 1 uA
Pin Capacitance Cpin 4 pF
Small Footprint Hi-Speed USB 2.0 Device PHY with UTMI Interface
Datasheet
Revision 1.5 (11-02-07) 14 SMSC USB3290
DATASHEET
Table 6.3 DC Electrical Characteristics: Analog I/O Pins (DP/DM) (Note 6.3)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
FS FUNCTIONALITY
Input levels
Differential Receiver Input
Sensitivity VDIFS | V(DP) - V(DM) | 0.2 V
Differential Receiver
Common-Mode Voltage VCMFS 0.8 2.5 V
Single-Ended Receiver Low
Level Input Voltage VILSE 0.8 V
Single-Ended Receiver High
Level Input Voltage VIHSE 2.0 V
Single-Ended Receiver
Hysteresis VHYSSE 0.050 0.150 V
Output Levels
Low Level Output Voltage VFSOL Pull-up resistor on DP;
RL = 1.5kΩ to VDD3.3
0.3 V
High Level Output Voltage VFSOH Pull-down resistor on DP,
DM;
RL = 15kΩ to GND
2.8 3.6 V
Termination
Driver Output Impedance for
HS and FS ZHSDRV Steady state drive
(See Figure 6.1)40.5 45 49.5 Ω
Input Impedance ZINP TX, RPU disabled 10 MΩ
Pull-up Resistor Impedance ZPU Bus Idle 0.900 1.24 1.575 kΩ
Pull-up Resistor Impedance ZPURX Device Receiving 1.425 2.26 3.09 kΩ
Termination Voltage For Pull-
up
Resistor On Pin DP
VTERM 3.0 3.6 V
HS FUNCTIONALITY
Input levels
HS Differential Input Sensitivity VDIHS | V(DP) - V(DM) | 100 mV
HS Data Signaling Common
Mode Voltage Range VCMHS -50 500 mV
HS Squelch Detection
Threshold (Differential) VHSSQ Squelch Threshold 100 mV
Unsquelch Threshold 150 mV
Output Levels
High Speed Low Level
Output Voltage (DP/DM
referenced to GND)
VHSOL 45Ω load -10 10 mV
Small Footprint Hi-Speed USB 2.0 Device PHY with UTMI Interface
Datasheet
SMSC USB3290 15 Revision 1.5 (11-02-07)
DATASHEET
Note 6.3 VDD3.3 = 3.0 to 3.6V; VSS = 0V; TA = -40oC to 85oC; unless otherwise specified.
Note 6.4 VDD3.3 = 3.0 to 3.6V; VSS = 0V; TA = -40oC to 85oC; unless otherwise specified.
High Speed High Level
Output Voltage (DP/DM
referenced to GND)
VHSOH 45Ω load 360 440 mV
High Speed IDLE Level
Output Voltage (DP/DM
referenced to GND)
VOLHS 45Ω load -10 10 mV
Chirp-J Output Voltage
(Differential) VCHIRPJ HS termination resistor
disabled, pull-up resistor
connected. 45Ω load.
700 1100 mV
Chirp-K Output Voltage
(Differential) VCHIRPK HS termination resistor
disabled, pull-up resistor
connected. 45Ω load.
-900 -500 mV
Leakage Current
OFF-State Leakage Current ILZ ± 1 uA
Port Capacitance
Transceiver Input Capacitance CIN Pin to GND 5 10 pF
Table 6.4 Dynamic Characteristics: Analog I/O Pins (DP/DM) (Note 6.4)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
FS Output Driver Timing
Rise Time TFSR CL = 50pF; 10 to 90% of
|VOH - VOL|420ns
Fall Time TFFF CL = 50pF; 10 to 90% of
|VOH - VOL|420ns
Output Signal Crossover
Voltage VCRS Excluding the first
transition from IDLE state 1.3 2.0 V
Differential Rise/Fall Time
Matching FRFM Excluding the first
transition from IDLE state 90 111.1 %
HS Output Driver Timing
Differential Rise Time THSR 500 ps
Differential Fall Time THSF 500 ps
Driver Waveform
Requirements Eye pattern of Template 1
in USB 2.0 specification See
Figure 6.2
High Speed Mode Timing
Receiver Waveform
Requirements Eye pattern of Template 4
in USB 2.0 specification See
Figure 6.2
Data Source Jitter and
Receiver Jitter Tolerance Eye pattern of Template 4
in USB 2.0 specification See
Figure 6.2
Table 6.3 DC Electrical Characteristics: Analog I/O Pins (DP/DM) (Note 6.3) (continued)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
Small Footprint Hi-Speed USB 2.0 Device PHY with UTMI Interface
Datasheet
Revision 1.5 (11-02-07) 16 SMSC USB3290
DATASHEET
Note 6.5 VDD3.3 = 3.0 to 3.6V; VSS = 0V; TA = -40oC to 85oC; unless otherwise specified.
6.1 Driver Characteristics of Full-Speed Drivers in High-Speed
Capable Transceivers
The USB3290 uses a differential output driver to drive the USB data signal onto the USB cable.
Figure 6.1 Full-Speed Driver VOH/IOH Characteristics for High-speed Capable Transceiveron page 17
shows the V/I characteristics for a full-speed driver which is part of a high-speed capable transceiver.
The normalized V/I curve for the driver must fall entirely inside the shaded region. The V/I region is
bounded by the minimum driver impedance above (40.5 Ohm) and the maximum driver impedance
below (49.5 Ohm). The output voltage must be within 10mV of ground when no current is flowing in
or out of the pin.
Table 6.5 Dynamic Characteristics: Digital UTMI Pins (Note 6.5)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
UTMI Timing
DATA[7:0] TPD Output Delay. Measured
from PHY output to the
rising edge of CLKOUT
25ns
RXVALID
RXACTIVE
RXERROR
LINESTATE[1:0]
TXREADY
DATA[7:0] TSU Setup Time. Measured
from PHY input to the
rising edge of CLKOUT.
5ns
TXVALID
OPMODE[1:0]
XCVRSELECT
TERMSELECT
DATA[7:0] THHold time. Measured from
the rising egde of
CLKOUT to the PHY input
signal edge.
0ns
TXVALID
OPMODE[1:0]
XCVRSELECT
TERMSELECT
Small Footprint Hi-Speed USB 2.0 Device PHY with UTMI Interface
Datasheet
SMSC USB3290 17 Revision 1.5 (11-02-07)
DATASHEET
Figure 6.1 Full-Speed Driver VOH/IOH Characteristics for High-speed Capable Transceiver
Figure 6.2 Full-Speed Driver VOL/IOL Characteristics for High-speed Capable Transceiver
Vout (Volts)
VOH
0
0
Drive High
0.698*VOH
Test Limit
Slope = 1/49.5 Ohm
Slope = 1/40.5 Ohm
0.566*VOH
-10.71 * |VOH|
-6.1 * |VOH|
Iout
(mA)
Vout (Volts) VOH
0
0
Drive Low
Iout
(mA)
22
1.09V 0.434*VOH
Test Limit
Slope = 1/40.5 Ohm
Slope = 1/49.5 Ohm
10.71 * |VOH|
Small Footprint Hi-Speed USB 2.0 Device PHY with UTMI Interface
Datasheet
Revision 1.5 (11-02-07) 18 SMSC USB3290
DATASHEET
6.2 High-speed Signaling Eye Patterns
High-speed USB signals are characterized using eye patterns. For measuring the eye patterns 4
points have been defined (see Figure 6.3). The Universal Serial Bus Specification Rev.2.0 defines the
eye patterns in several ‘templates’. The two templates that are relevant to the PHY are shown below.
Figure 6.3 Eye Pattern Measurement Planes
USB Cable
Transceiver
Device Circuit Board
Transceiver
Hub Circuit Board
Connector
Traces Traces
A Connector
B
TP1 TP2 TP3 TP4
Small Footprint Hi-Speed USB 2.0 Device PHY with UTMI Interface
Datasheet
SMSC USB3290 19 Revision 1.5 (11-02-07)
DATASHEET
The eye pattern in Figure 6.4 defines the transmit waveform requirements for a hub (measured at TP2
of Figure 6.3) or a device without a captive cable (measured at TP3 of Figure 6.3). The corresponding
signal levels and timings are given in table below. Time is specified as a percentage of the unit interval
(UI), which represents the nominal bit duration for a 480 Mbit/s transmission rate.
Figure 6.4 Eye Pattern for Transmit Waveform and Eye Pattern Definition
VOLTAGE LEVEL (D+, D-) TIME (% OF UNIT INTERVAL)
Level 1 525mV in UI following a transition,
475mV in all others N/A
Level 2 -525mV in UI following a transition,
-475mV in all others N/A
Point 1 0V 7.5% UI
Point 2 0V 92.5% UI
Point 3 300mV 37.5% UI
Point 4 300mV 62.5% UI
Point 5 -300mV 37.5% UI
Point 6 -300mV 62.5% UI
Differential
-400mV
Differential
400mV
Unit Interval 100%
Level 2
Level 1
Point 1 Point 2
Point 4 Point 3
Point 6 Point 5
0%
0 Volts
Differential
Small Footprint Hi-Speed USB 2.0 Device PHY with UTMI Interface
Datasheet
Revision 1.5 (11-02-07) 20 SMSC USB3290
DATASHEET
The eye pattern in Figure 6.5 defines the receiver sensitivity requirements for a hub (signal applied at
test point TP2 of Figure 6.3) or a device without a captive cable (signal applied at test point TP3 of
Figure 6.3). The corresponding signal levels and timings are given in the table below. Timings are
given as a percentage of the unit interval (UI), which represents the nominal bit duration for a 480
Mbit/s transmission rate.
Figure 6.5 Eye Pattern for Receive Waveform and Eye Pattern Definition
VOLTAGE LEVEL (D+, D-) TIME (% OF UNIT INTERVAL)
Level 1 575mV N/A
Level 2 -575mV N/A
Point 1 0V 15% UI
Point 2 0V 85% UI
Point 3 150mV 35% UI
Point 4 150mV 65% UI
Point 5 -150mV 35% UI
Point 6 -150mV 65% UI
Point 1
0% 100%
Point 2
Level 2
Level 1
Point 3 Point 4
Point 5 Point 6
Differential
-400mV
Differential
400mV
Differential
0 Voltｓ
Small Footprint Hi-Speed USB 2.0 Device PHY with UTMI Interface
Datasheet
SMSC USB3290 21 Revision 1.5 (11-02-07)
DATASHEET
Chapter 7 Functional Overview
Figure 2.1 on page 7 shows the functional block diagram of the USB3290. Each of the functions is
described in detail below.
7.1 Modes of Operation
The USB3290 supports an 8-bit bi-directional parallel interface.
CLKOUT runs at 60MHz
The 8-bit data bus (DATA[7:0]) is used for transmit when TXVALID = 1
The 8-bit data bus (DATA[7:0]) is used for receive when TXVALID = 0
7.2 System Clocking
This block connects to either an external 24MHz crystal or an external clock source and generates a
480MHz multi-phase clock. The clock is used in the CRC block to over-sample the incoming received
data, resynchronize the transmit data, and is divided down to 60MHz (CLKOUT) which acts as the
system byte clock. The PLL block also outputs a clock valid signal to the other parts of the transceiver
when the clock signal is stable. All UTMI signals are synchronized to the CLKOUT output. The
behavior of the CLKOUT is as follows:
Produce the first CLKOUT transition no later than 5.6ms after negation of SUSPENDN. The
CLKOUT signal frequency error is less than 10% at this time.
The CLKOUT signal will fully meet the required accuracy of ±500ppm no later than 1.4ms after the
first transition of CLKOUT.
In HS mode there is one CLKOUT cycle per byte time. The frequency of CLKOUT does not change
when the PHY is switched between HS to FS modes. In FS mode there are 5 CLKOUT cycles per FS
bit time, typically 40 CLKOUT cycles per FS byte time. If a received byte contains a stuffed bit then
the byte boundary can be stretched to 45 CLKOUT cycles, and two stuffed bits would result in a 50
CLKOUT cycles.
Figure 7.1 shows the relationship between CLKOUT and the transmit data transfer signals in FS mode.
TXREADY is only asserted for one CLKOUT per byte time to signal the SIE that the data on the DATA
lines has been read by the PHY. The SIE may hold the data on the DATA lines for the duration of the
byte time. Transitions of TXVALID must meet the defined setup and hold times relative to CLKOUT.
Figure 7.1 FS CLK Relationship to Transmit Data and Control Signals
Small Footprint Hi-Speed USB 2.0 Device PHY with UTMI Interface
Datasheet
Revision 1.5 (11-02-07) 22 SMSC USB3290
DATASHEET
Figure 7.2 shows the relationship between CLKOUT and the receive data control signals in FS mode.
RXACTIVE "frames" a packet, transitioning only at the beginning and end of a packet. However
transitions of RXVALID may take place any time 8 bits of data are available. Figure 7.1 also shows
how RXVALID is only asserted for one CLKOUT cycle per byte time even though the data may be
presented for the full byte time. The XCVRSELECT signal determines whether the HS or FS timing
relationship is applied to the data and control signals.
7.3 Clock and Data Recovery Circuit
This block consists of the Clock and Data Recovery Circuit and the Elasticity Buffer. The Elasticity
Buffer is used to compensate for differences between the transmitting and receiving clock domains.
The USB 2.0 specification defines a maximum clock error of ±1000ppm of drift.
7.4 TX Logic
This block receives parallel data bytes placed on the DATA bus and performs the necessary transmit
operations. These operations include parallel to serial conversion, bit stuffing and NRZI encoding.
Upon valid assertion of the proper TX control lines by the SIE and TX State Machine, the TX LOGIC
block will synchronously shift, at either the FS or HS rate, the data to the FS/HS TX block to be
transmitted on the USB cable. Data transmit timing is shown in Figure 7.3.
Figure 7.2 FS CLK Relationship to Receive Data and Control Signals
Figure 7.3 Transmit Timing for a Data Packet
Small Footprint Hi-Speed USB 2.0 Device PHY with UTMI Interface
Datasheet
SMSC USB3290 23 Revision 1.5 (11-02-07)
DATASHEET
The behavior of the Transmit State Machine is described below.
Asserting a RESET forces the transmit state machine into the Reset state which negates
TXREADY. When RESET is negated the transmit state machine will enter a wait state.
The SIE asserts TXVALID to begin a transmission.
After the SIE asserts TXVALID it can assume that the transmission has started when it detects
TXREADY has been asserted.
The SIE must assume that the USB3290 has consumed a data byte if TXREADY and TXVALID
are asserted on the rising edge of CLKOUT.
The SIE must have valid packet information (PID) asserted on the DATA bus coincident with the
assertion of TXVALID.
TXREADY is sampled by the SIE on the rising edge of CLKOUT.
The SIE negates TXVALID to complete a packet. Once negated, the transmit logic will never
reassert TXREADY until after the EOP has been generated. (TXREADY will not re-assert until
TXVALD asserts again.
The USB3290 is ready to transmit another packet immediately, however the SIE must conform to
the minimum inter-packet delays identified in the USB 2.0 specification.
7.5 RX Logic
This block receives serial data from the CRC block and processes it to be transferred to the SIE on
the DATA bus. The processing involved includes NRZI decoding, bit unstuffing, and serial to parallel
conversion. Upon valid assertion of the proper RX control lines by the RX State Machine, the RX Logic
block will provide bytes to the DATA bus as shown in the figures below. The behavior of the Receive
State Machine is described below.
The assertion of RESET will force the Receive State Machine into the Reset state. The Reset state
deasserts RXACTIVE and RXVALID. When the RESET signal is deasserted the Receive State
Machine enters the RX Wait state and starts looking for a SYNC pattern on the USB. When a SYNC
pattern is detected the state machine will enter the Strip SYNC state and assert RXACTIVE. The length
of the received Hi-Speed SYNC pattern varies and can be up to 32 bits long or as short as 12 bits
long when at the end of five hubs. As a result, the state machine may remain in the Strip SYNC state
for several byte times before capturing the first byte of data and entering the RX Data state.
After valid serial data is received, the state machine enters the RX Data state, where the data is loaded
into the RX Holding Register on the rising edge of CLKOUT and RXVALID is asserted. The SIE must
clock the data off the DATA bus on the next rising edge of CLKOUT. If OPMODE = Normal, then
stuffed bits are stripped from the data stream. Each time 8 stuffed bits are accumulated the state
machine will enter the RX Data Wait state, negating RXVALID thus skipping a byte time.
Figure 7.4 Receive Timing for Data with Unstuffed Bits
Small Footprint Hi-Speed USB 2.0 Device PHY with UTMI Interface
Datasheet
Revision 1.5 (11-02-07) 24 SMSC USB3290
DATASHEET
When the EOP is detected the state machine will enter the Strip EOP state and negate RXACTIVE
and RXVALID. After the EOP has been stripped the Receive State Machine will reenter the RX Wait
state and begin looking for the next packet.
The behavior of the Receive State Machine is described below:
RXACTIVE and RXREADY are sampled on the rising edge of CLKOUT.
In the RX Wait state the receiver is always looking for SYNC.
The USB3290 asserts RXACTIVE when SYNC is detected (Strip SYNC state).
The USB3290 negates RXACTIVE when an EOP is detected and the elasticity buffer is empty
(Strip EOP state).
When RXACTIVE is asserted, RXVALID will be asserted if the RX Holding Register is full.
RXVALID will be negated if the RX Holding Register was not loaded during the previous byte time.
This will occur if 8 stuffed bits have been accumulated.
The SIE must be ready to consume a data byte if RXACTIVE and RXVALID are asserted (RX Data
state).
Figure 7.5 shows the timing relationship between the received data (DP/DM), RXVALID,
RXACTIVE, RXERROR and DATA signals.
Notes:
The USB 2.0 Transceiver does NOT decode Packet ID's (PIDs). They are passed to the SIE for
decoding.
Figure 7.5, Figure 7.6 and Figure 7.7 are timing examples of a HS/FS PHY when it is in HS mode.
When a HS/FS PHY is in FS Mode there are approximately 40 CLKOUT cycles every byte time.
The Receive State Machine assumes that the SIE captures the data on the DATA bus if RXACTIVE
and RXVALID are asserted. In FS mode, RXVALID will only be asserted for one CLKOUT per byte
time.
In Figure 7.5, Figure 7.6 and Figure 7.7 the SYNC pattern on DP/DM is shown as one byte long.
The SYNC pattern received by a device can vary in length. These figures assume that all but the
last 12 bits have been consumed by the hubs between the device and the host controller.
Figure 7.5 Receive Timing for a Handshake Packet (no CRC)
Small Footprint Hi-Speed USB 2.0 Device PHY with UTMI Interface
Datasheet
SMSC USB3290 25 Revision 1.5 (11-02-07)
DATASHEET
The receivers connect directly to the USB cable. The block contains a separate differential receiver
for HS and FS mode. Depending on the mode, the selected receiver provides the serial data stream
through the mulitplexer to the RX Logic block. The FS mode section of the FS/HS RX block also
consists of a single-ended receiver on each of the data lines to determine the correct FS LINESTATE.
For HS mode support, the FS/HS RX block contains a squelch circuit to insure that noise is never
interpreted as data.
Figure 7.6 Receive Timing for Setup Packet
Figure 7.7 Receive Timing for Data Packet (with CRC-16)
Small Footprint Hi-Speed USB 2.0 Device PHY with UTMI Interface
Datasheet
Revision 1.5 (11-02-07) 26 SMSC USB3290
DATASHEET
7.6 USB 2.0 Transceiver
The SMSC Hi-Speed USB 2.0 Transceiver consists of the High Speed and Full Speed Transceivers,
and the Termination resistors.
7.6.1 High Speed and Full Speed Transceivers
The USB3290 transceiver meets all requirements in the USB 2.0 specification.
The receivers connect directly to the USB cable. This block contains a separate differential receiver
for HS and FS mode. Depending on the mode, the selected receiver provides the serial data stream
through the multiplexer to the RX Logic block. The FS mode section of the FS/HS RX block also
consists of a single-ended receiver on each of the data lines to determine the correct FS linestate. For
HS mode support, the FS/HS RX block contains a squelch circuit to insure that noise is never
interpreted as data.
The transmitters connect directly to the USB cable. The block contains a separate differential FS and
HS transmitter which receive encoded, bit stuffed, serialized data from the TX Logic block and transmit
it on the USB cable.
7.6.2 Termination Resistors
The USB3290 transceiver fully integrates all of the USB termination resistors. The USB3290 includes
the 1.5kΩ pull-up resistor on DP. In addition the 45Ω high speed termination resistors are also
integrated. These integrated resistors require no tuning or trimming. The state of the resistors is
determined by the operating mode of the PHY. The possible valid resistor combinations are shown in
Table 7.1.
RPU_DP_EN activates the 1.5kΩ DP pull-up resistor
HSTERM_EN activates the 45Ω DP and DM high speed termination resistors
Table 7.1 DP/DM Termination vs. Signaling Mode
SIGNALING MODE
UTMI+ INTERFACE SETTINGS RESISTOR
SETTINGS
XCVRSELECT
TERMSELECT
OPMODE[1:0]
RPU_DP_EN
HSTERM_EN
Tri-State Drivers Xb Xb 01b 0b 0b
Power-up 1b 0b 00b 0b 0b
Peripheral Chirp 0b 1b 10b 1b 0b
Peripheral HS 0b 0b 00b 0b 1b
Peripheral FS 1b 1b 00b 1b 0b
Peripheral HS/FS Suspend 1b 1b 00b 1b 0b
Peripheral HS/FS Resume 1b 1b 10b 1b 0b
Peripheral Test J/Test K 0b 0b 10b 0b 1b
Small Footprint Hi-Speed USB 2.0 Device PHY with UTMI Interface
Datasheet
SMSC USB3290 27 Revision 1.5 (11-02-07)
DATASHEET
7.6.3 Bias Generator
This block consists of an internal bandgap reference circuit used for generating the high speed driver
currents and the biasing of the analog circuits. This block requires an external 12kΩ, 1% tolerance,
external reference resistor connected from RBIAS to ground.
7.7 Crystal Oscillator and PLL
The USB3290 uses an internal crystal driver and PLL sub-system to provide a clean 480MHz reference
clock that is used by the PHY during both transmit and receive. The USB3290 requires a clean 24MHz
crystal or clock as a frequency reference. If the 24MHz reference is noisy or off frequency the PHY
may not operate correctly.
The USB3290 can use either a crystal or an external clock oscillator for the 24MHz reference. The
crystal is connected to the XI and XO pins as shown in the application diagram, Figure 8.10. If a clock
oscillator is used the clock should be connected to the XI input and the XO pin left floating. When a
external clock is used the XI pin is designed to be driven with a 0 to 3.3 volt signal. When using an
external clock the user needs to take care to ensure the external clock source is clean enough to not
degrade the high speed eye performance.
Once, the 480MHz PLL has locked to the correct frequency it will drive the CLKOUT pin with a 60MHz
clock.
7.8 Internal Regulators and POR
The USB3290 includes an integrated set of built in power management functions. These power
management features include a POR generation and allow the USB3290 to be powered from a single
3.3 volt power supply. This reduces the bill of materials and simplifies product design.
7.8.1 Internal Regulators
The USB3290 has two integrated 3.3 volt to 1.8 volt regulators. These regulators require an external
4.7uF +/-20% low ESR bypass capacitor to ensure stability. X5R or X7R ceramic capacitors are
recommended since they exhibit an ESR lower than 0.1 ohm at frequencies greater than 10kHz.
The two regulator outputs, which require bypass capacitors, are the pins labeled VDDA1.8 and
VDD1.8. Each pin requires a 4.7uF bypass capacitor placed as close to the pin as possible.
Note: The USB3290 regulators are designed to generate a 1.8 volt supply for the USB3290 only.
Using the regulators to provide current for other circuits is not recommended and SMSC does
not guarantee USB performance or regulator stability.
7.8.2 Power On Reset (POR)
The USB3290 provides an internal POR circuit that generates a reset pulse once the PHY supplies
are stable.
7.8.3 Reset Pin
The UTMI+ Digital can be reset at any time with the RESET pin. The RESET pin of the USB3290 may
be asynchronously asserted and de-asserted so long as it is held in the asserted state continuously
for a duration greater than one CLKOUT cycle. The RESET input may be asserted when the USB3290
CLKOUT signal is not active (i.e. in the suspend state caused by asserting the SUSPENDN input) but
reset must only be de-asserted when the USB3290 CLKOUT signal is active and the RESET has been
held asserted for a duration greater than one CKOUT clock cycle. No other PHY digital input signals
may change state for two CLKOUT clock cycles after the de-assertion of the reset signal.
Small Footprint Hi-Speed USB 2.0 Device PHY with UTMI Interface
Datasheet
Revision 1.5 (11-02-07) 28 SMSC USB3290
DATASHEET
Chapter 8 Application Notes
The following sections consist of select functional explanations to aid in implementing the USB3290
into a system. For complete description and specifications consult the USB 2.0 Transceiver Macrocell
Interface Specification and Universal Serial Bus Specification Revision 2.0.
8.1 Linestate
The voltage thresholds that the LINESTATE[1:0] signals use to reflect the state of DP and DM depend
on the state of XCVRSELECT. LINESTATE[1:0] uses HS thresholds when the HS transceiver is
enabled (XCVRSELECT = 0) and FS thresholds when the FS transceiver is enabled (XCVRSELECT
= 1). There is not a concept of variable single-ended thresholds in the USB 2.0 specification for HS
mode.
The HS receiver is used to detect Chirp J or K, where the output of the HS receiver is always qualified
with the Squelch signal. If squelched, the output of the HS receiver is ignored. In the USB3290, as
an alternative to using variable thresholds for the single-ended receivers, the following approach is
used.
In HS mode, 3ms of no USB activity (IDLE state) signals a reset. The SIE monitors LINESTATE[1:0]
for the IDLE state. To minimize transitions on LINESTATE[1:0] while in HS mode, the presence of
!Squelch is used to force LINESTATE[1:0] to a J state.
Table 8.1 Linestate States
STATE OF DP/DM LINES
LINESTATE[1:0] FULL SPEED
XCVRSELECT =1
TERMSELECT=1
HIGH SPEED
XCVRSELECT =0
TERMSELECT=0
CHIRP MODE
XCVRSELECT =0
TERMSELECT=1LS[1] LS[0]
0 0 SE0 Squelch Squelch
0 1 J !Squelch !Squelch &
HS Differential Receiver
Output
1 0 K Invalid !Squelch &
!HS Differential Receiver
Output
1 1 SE1 Invalid Invalid
Small Footprint Hi-Speed USB 2.0 Device PHY with UTMI Interface
Datasheet
SMSC USB3290 29 Revision 1.5 (11-02-07)
DATASHEET
8.2 OPMODES
The OPMODE[1:0] pins allow control of the operating modes.
The OPMODE[1:0] signals are normally changed only when the transmitter and the receiver are
quiescent, i.e. when entering a test mode or for a device initiated resume.
When using OPMODE[1:0] = 10 (state 2), OPMODES are set, and then 5 60MHz clocks later,
TXVALID is asserted. In this case, the SYNC and EOP patterns are not transmitted.
The only exception to this is when OPMODE[1:0] is set to state 2 while TXVALID has been asserted
(the transceiver is transmitting a packet), in order to flag a transmission error. In this case, the
USB3290 has already transmitted the SYNC pattern so upon negation of TXVALID the EOP must also
be transmitted to properly terminate the packet. Changing the OPMODE[1:0] signals under all other
conditions, while the transceiver is transmitting or receiving data will generate undefined results.
Under no circumstances should the device controller change OPMODE while the DP/DM lines are still
transmitting or unpredictable changes on DP/DM are likely to occur. The same applies for
TERMSELECT and XCVRSELECT.
8.3 Test Mode Support
Table 8.2 Operational Modes
MODE[1:0] STATE# STATE NAME DESCRIPTION
00 0 Normal Operation Transceiver operates with normal USB data encoding and
decoding
01 1 Non-Driving Allows the transceiver logic to support a soft disconnect feature
which tri-states both the HS and FS transmitters, and removes
any termination from the USB making it appear to an upstream
port that the device has been disconnected from the bus
10 2 Disable Bit Stuffing
and NRZI encoding Disables bitstuffing and NRZI encoding logic so that 1's loaded
from the DATA bus become 'J's on the DP/DM and 0's become
'K's
11 3 Reserved N/A
Table 8.3 USB 2.0 Test Modes
USB 2.0 TEST MODES
USB3290 SETUP
OPERATIONAL MODE SIE TRANSMITTED DATA XCVRSELECT &
TERMSELECT
SE0_NAK State 0 No transmit HS
J State 2 All '1's HS
K State 2 All '0's HS
Test_Packet State 0 Test Packet data HS
Small Footprint Hi-Speed USB 2.0 Device PHY with UTMI Interface
Datasheet
Revision 1.5 (11-02-07) 30 SMSC USB3290
DATASHEET
8.4 SE0 Handling
For FS operation, IDLE is a J state on the bus. SE0 is used as part of the EOP or to indicate reset.
When asserted in an EOP, SE0 is never asserted for more than 2 bit times. The assertion of SE0 for
more than 2.5us is interpreted as a reset by the device operating in FS mode.
For HS operation, IDLE is a SE0 state on the bus. SE0 is also used to reset a HS device. A HS
device cannot use the 2.5us assertion of SE0 (as defined for FS operation) to indicate reset since the
bus is often in this state between packets. If no bus activity (IDLE) is detected for more than 3ms, a
HS device must determine whether the downstream facing port is signaling a suspend or a reset. The
following section details how this determination is made. If a reset is signaled, the HS device will then
initiate the HS Detection Handshake protocol.
8.5 Reset Detection
If a device in HS mode detects bus inactivity for more than 3ms (T1), it reverts to FS mode. This
enables the FS pull-up on the DP line in an attempt to assert a continuous FS J state on the bus. The
SIE must then check LINESTATE for the SE0 condition. If SE0 is asserted at time T2, then the
upstream port is forcing the reset state to the device (i.e., a Driven SE0). The device will then initiate
the HS detection handshake protocol.
Figure 8.1 Reset Timing Behavior (HS Mode)
Table 8.4 Reset Timing Values (HS Mode)
TIMING
PARAMETER DESCRIPTION VALUE
HS Reset T0 Bus activity ceases, signaling either a reset
or a SUSPEND. 0 (reference)
T1 Earliest time at which the device may place
itself in FS mode after bus activity stops. HS Reset T0 + 3. 0ms < T1 < HS Reset T0
+ 3.125ms
T2 SIE samples LINESTATE. If LINESTATE =
SE0, then the SE0 on the bus is due to a
Reset state. The device now enters the HS
Detection Handshake protocol.
T1 + 100µs < T2 <
T1 + 875µs
Small Footprint Hi-Speed USB 2.0 Device PHY with UTMI Interface
Datasheet
SMSC USB3290 31 Revision 1.5 (11-02-07)
DATASHEET
8.6 Suspend Detection
If a HS device detects SE0 asserted on the bus for more than 3ms (T1), it reverts to FS mode. This
enables the FS pull-up on the DP line in an attempt to assert a continuous FS J state on the bus. The
SIE must then check LINESTATE for the J condition. If J is asserted at time T2, then the upstream
port is asserting a soft SE0 and the USB is in a J state indicating a suspend condition. By time T4
the device must be fully suspended.
Figure 8.2 Suspend Timing Behavior (HS Mode)
Table 8.5 Suspend Timing Values (HS Mode)
TIMING
PARAMETER DESCRIPTION VALUE
HS Reset T0 End of last bus activity, signaling either a reset
or a SUSPEND. 0 (reference)
T1 The time at which the device must place itself
in FS mode after bus activity stops. HS Reset T0 + 3. 0ms < T1 < HS Reset T0
+ 3.125ms
T2 SIE samples LINESTATE. If LINESTATE = 'J',
then the initial SE0 on the bus (T0 - T1) had
been due to a Suspend state and the SIE
remains in HS mode.
T1 + 100 µs < T2 <
T1 + 875µs
T3 The earliest time where a device can issue
Resume signaling. HS Reset T0 + 5ms
T4 The latest time that a device must actually be
suspended, drawing no more than the
suspend current from the bus.
HS Reset T0 + 10ms
Small Footprint Hi-Speed USB 2.0 Device PHY with UTMI Interface
Datasheet
Revision 1.5 (11-02-07) 32 SMSC USB3290
DATASHEET
8.7 HS Detection Handshake
The High Speed Detection Handshake process is entered from one of three states: suspend, active
FS or active HS. The downstream facing port asserting an SE0 state on the bus initiates the HS
Detection Handshake. Depending on the initial state, an SE0 condition can be asserted from 0 to 4
ms before initiating the HS Detection Handshake. These states are described in the USB 2.0
specification.
There are three ways in which a device may enter the HS Handshake Detection process:
1. If the device is suspended and it detects an SE0 state on the bus it may immediately enter the HS
handshake detection process.
2. If the device is in FS mode and an SE0 state is detected for more than 2.5µs. it may enter the HS
handshake detection process.
3. If the device is in HS mode and an SE0 state is detected for more than 3.0ms. it may enter the
HS handshake detection process. In HS mode, a device must first determine whether the SE0 state
is signaling a suspend or a reset condition. To do this the device reverts to FS mode by placing
XCVRSELECT and TERMSELECT into FS mode. The device must not wait more than 3.125ms
before the reversion to FS mode. After reverting to FS mode, no less than 100µs and no more
than 875µs later the SIE must check the LINESTATE signals. If a J state is detected the device
will enter a suspend state. If an SE0 state is detected, then the device will enter the HS Handshake
detection process.
In each case, the assertion of the SE0 state on the bus initiates the reset. The minimum reset interval
is 10ms. Depending on the previous mode that the bus was in, the delay between the initial assertion
of the SE0 state and entering the HS Handshake detection can be from 0 to 4ms.
This transceiver design pushes as much of the responsibility for timing events on to the SIE as
possible, and the SIE requires a stable CLKOUT signal to perform accurate timing. In case 2 and 3
above, CLKOUT has been running and is stable, however in case 1 the USB3290 is reset from a
suspend state, and the internal oscillator and clocks of the transceiver are assumed to be powered
down. A device has up to 6ms after the release of SUSPENDN to assert a minimum of a 1ms Chirp K.
8.8 HS Detection Handshake – FS Downstream Facing Port
Upon entering the HS Detection process (T0) XCVRSELECT and TERMSELECT are in FS mode. The
DP pull-up is asserted and the HS terminations are disabled. The SIE then sets OPMODE to Disable
Bit Stuffing and NRZI encoding, XCVRSELECT to HS mode, and begins the transmission of all 0's
data, which asserts a HS K (chirp) on the bus (T1). The device chirp must last at least 1.0ms, and
must end no later than 7.0ms after HS Reset T0. At time T1 the device begins listening for a chirp
sequence from the host port.
If the downstream facing port is not HS capable, then the HS K asserted by the device is ignored and
the alternating sequence of HS Chirp K’s and J’s is not generated. If no chirps are detected (T4) by
the device, it will enter FS mode by returning XCVRSELECT to FS mode.
Small Footprint Hi-Speed USB 2.0 Device PHY with UTMI Interface
Datasheet
SMSC USB3290 33 Revision 1.5 (11-02-07)
DATASHEET
Notes:
T0 may occur to 4ms after HS Reset T0.
The SIE must assert the Chirp K for 66000 CLKOUT cycles to ensure a 1ms minimum duration.
Figure 8.3 HS Detection Handshake Timing Behavior (FS Mode)
Table 8.6 HS Detection Handshake Timing Values (FS Mode)
TIMING
PARAMETER DESCRIPTION VALUE
T0 HS Handshake begins. DP pull-up enabled, HS
terminations disabled. 0 (reference)
T1 Device enables HS Transceiver and asserts Chirp
K on the bus. T0 < T1 < HS Reset T0 + 6.0ms
T2 Device removes Chirp K from the bus. 1ms
minimum width. T1 + 1.0 ms < T2 <
HS Reset T0 + 7.0ms
T3 Earliest time when downstream facing port may
assert Chirp KJ sequence on the bus. T2 < T3 < T2+100µs
T4 Chirp not detected by the device. Device reverts to
FS default state and waits for end of reset. T2 + 1.0ms < T4 <
T2 + 2.5ms
T5 Earliest time at which host port may end reset HS Reset T0 + 10ms
Small Footprint Hi-Speed USB 2.0 Device PHY with UTMI Interface
Datasheet
Revision 1.5 (11-02-07) 34 SMSC USB3290
DATASHEET
8.9 HS Detection Handshake – HS Downstream Facing Port
Upon entering the HS Detection process (T0) XCVRSELECT and TERMSELECT are in FS mode. The
DP pull-up is asserted and the HS terminations are disabled. The SIE then sets OPMODE to Disable
Bit Stuffing and NRZI encoding, XCVRSELECT to HS mode, and begins the transmission of all 0's
data, which asserts a HS K (chirp) on the bus (T1). The device chirp must last at least 1.0ms, and
must end no later than 7.0ms after HS Reset T0. At time T1 the device begins listening for a chirp
sequence from the downstream facing port. If the downstream facing port is HS capable then it will
begin generating an alternating sequence of Chirp K’s and Chirp J’s (T3) after the termination of the
chirp from the device (T2). After the device sees the valid chirp sequence Chirp K-J-K-J-K-J (T6), it
will enter HS mode by setting TERMSELECT to HS mode (T7).
Figure 8.4 provides a state diagram for Chirp K-J-K-J-K-J validation. Prior to the end of reset (T9) the
device port must terminate the sequence of Chirp K’s and Chirp J’s (T8) and assert SE0 (T8-T9). Note
that the sequence of Chirp K’s and Chirp J’s constitutes bus activity.
The Chirp K-J-K-J-K-J sequence occurs too slow to propagate through the serial data path, therefore
LINESTATE signal transitions must be used by the SIE to step through the Chirp K-J-K-J-K-J state
diagram, where "K State" is equivalent to LINESTATE = K State and "J State" is equivalent to
LINESTATE = J State. The SIE must employ a counter (Chirp Count) to count the number of Chirp K
and Chirp J states. Note that LINESTATE does not filter the bus signals so the requirement that a bus
state must be "continuously asserted for 2.5µs" must be verified by the SIE sampling the LINESTATE
signals.
Figure 8.4 Chirp K-J-K-J-K-J Sequence Detection State Diagram
Detect K?
Start Chirp
K-J-K-J-K-J
detection
INC Chirp
Count
K State
!K
Detect J?
INC Chirp
Count
J State
!J
Chirp Count != 6
& !SE0
Chirp Count
= 0
Chirp Count != 6
& !SE0
Chirp Valid
Chirp
Invalid
SE0
Chir
Count
Small Footprint Hi-Speed USB 2.0 Device PHY with UTMI Interface
Datasheet
SMSC USB3290 35 Revision 1.5 (11-02-07)
DATASHEET
Figure 8.5 HS Detection Handshake Timing Behavior (HS Mode)
Table 8.7 Reset Timing Values
TIMING
PARAMETER DESCRIPTION VALUE
T0 HS Handshake begins. DP pull-up enabled, HS
terminations disabled. 0 (reference)
T1 Device asserts Chirp K on the bus. T0 < T1 < HS Reset T0 + 6.0ms
T2 Device removes Chirp K from the bus. 1 ms
minimum width. T0 + 1.0ms < T2 <
HS Reset T0 + 7.0ms
T3 Downstream facing port asserts Chirp K on the
bus. T2 < T3 < T2+100µs
T4 Downstream facing port toggles Chirp K to Chirp J
on the bus. T3 + 40µs < T4 < T3 + 60µs
T5 Downstream facing port toggles Chirp J to Chirp K
on the bus. T4 + 40µs < T5 < T4 + 60µs
T6 Device detects downstream port chirp. T6
T7 Chirp detected by the device. Device removes DP
pull-up and asserts HS terminations, reverts to HS
default state and waits for end of reset.
T6 < T7 < T6 + 500µs
T8 Terminate host port Chirp K-J sequence (Repeating
T4 and T5) T9 - 500µs < T8 < T9 - 100µs
T9 The earliest time at which host port may end reset.
The latest time, at which the device may remove
the DP pull-up and assert the HS terminations,
reverts to HS default state.
HS Reset T0 + 10ms
Small Footprint Hi-Speed USB 2.0 Device PHY with UTMI Interface
Datasheet
Revision 1.5 (11-02-07) 36 SMSC USB3290
DATASHEET
Notes:
T0 may be up to 4ms after HS Reset T0.
The SIE must use LINESTATE to detect the downstream port chirp sequence.
Due to the assertion of the HS termination on the host port and FS termination on the device port,
between T1 and T7 the signaling levels on the bus are higher than HS signaling levels and are
less than FS signaling levels.
8.10 HS Detection Handshake – Suspend Timing
If reset is entered from a suspended state, the internal oscillator and clocks of the transceiver are
assumed to be powered down. Figure 8.6 shows how CLKOUT is used to control the duration of the
chirp generated by the device.
When reset is entered from a suspended state (J to SE0 transition reported by LINESTATE),
SUSPENDN is combinatorially negated at time T0 by the SIE. It takes approximately 5 milliseconds
for the transceiver's oscillator to stabilize. The device does not generate any transitions of the CLKOUT
signal until it is "usable" (where "usable" is defined as stable to within ±10% of the nominal frequency
and the duty cycle accuracy 50±5%).
The first transition of CLKOUT occurs at T1. The SIE then sets OPMODE to Disable Bit Stuffing and
NRZI encoding, XCVRSELECT to HS mode, and must assert a Chirp K for 66000 CLKOUT cycles to
ensure a 1ms minimum duration. If CLKOUT is 10% fast (66MHz) then Chirp K will be 1.0ms. If
CLKOUT is 10% slow (54 MHz) then Chirp K will be 1.2ms. The 5.6ms requirement for the first
CLKOUT transition after SUSPENDN, ensures enough time to assert a 1ms Chirp K and still complete
before T3. Once the Chirp K is completed (T3) the SIE can begin looking for host chirps and use
CLKOUT to time the process. At this time, the device follows the same protocol as in Section 8.9,
"HS Detection Handshake – HS Downstream Facing Port" for completion of the High Speed
Handshake.
Small Footprint Hi-Speed USB 2.0 Device PHY with UTMI Interface
Datasheet
SMSC USB3290 37 Revision 1.5 (11-02-07)
DATASHEET
To detect the assertion of the downstream Chirp K's and Chirp J's for 2.5us {TFILT}, the SIE must see
the appropriate LINESTATE signals asserted continuously for 165 CLKOUT cycles.
Figure 8.6 HS Detection Handshake Timing Behavior from Suspend
Table 8.8 HS Detection Handshake Timing Values from Suspend
TIMING
PARAMETER DESCRIPTION VALUE
T0 While in suspend state an SE0 is detected on the USB. HS
Handshake begins. D+ pull-up enabled, HS terminations
disabled, SUSPENDN negated.
0 (HS Reset T0)
T1 First transition of CLKOUT. CLKOUT "Usable" (frequency
accurate to ±10%, duty cycle accurate to 50±5). T0 < T1 < T0 + 5.6ms
T2 Device asserts Chirp K on the bus. T1 < T2 < T0 + 5.8ms
T3 Device removes Chirp K from the bus. (1 ms minimum width)
and begins looking for host chirps. T2 + 1.0 ms < T3 <
T0 + 7.0 ms
T4 CLK "Nominal" (CLKOUT is frequency accurate to ±500
ppm, duty cycle accurate to 50±5). T1 < T3 < T0 + 20.0ms
CLK60
Look for host chirps
Device Chirp K
SUSPENDN
DP/DM
TERMSELECT
TXVALID
SE0
J
CLK power up time
XCVRSELECT
OPMODE 1
OPMODE 0
time
T0 T3 T4
T1 T2
Small Footprint Hi-Speed USB 2.0 Device PHY with UTMI Interface
Datasheet
Revision 1.5 (11-02-07) 38 SMSC USB3290
DATASHEET
8.11 Assertion of Resume
In this case, an event internal to the device initiates the resume process. A device with remote wake-
up capability must wait for at least 5ms after the bus is in the idle state before sending the remote
wake-up resume signaling. This allows the hubs to get into their suspend state and prepare for
propagating resume signaling.
The device has 10ms where it can draw a non-suspend current before it must drive resume signaling.
At the beginning of this period the SIE may negate SUSPENDN, allowing the transceiver (and its
oscillator) to power up and stabilize.
Figure 8.7 illustrates the behavior of a device returning to HS mode after being suspended. At T4, a
device that was previously in FS mode would maintain TERMSELECT and XCVRSELECT high.
To generate resume signaling (FS 'K') the device is placed in the "Disable Bit Stuffing and NRZI
encoding" Operational Mode (OPMODE [1:0] = 10), TERMSELECT and XCVRSELECT must be in FS
mode, TXVALID asserted, and all 0's data is presented on the DATA bus for at least 1ms (T1 - T2).
Figure 8.7 Resume Timing Behavior (HS Mode)
Table 8.9 Resume Timing Values (HS Mode)
TIMING
PARAMETER DESCRIPTION VALUE
T0 Internal device event initiating the resume
process 0 (reference)
T1 Device asserts FS 'K' on the bus to signal
resume request to downstream port T0 < T1 < T0 + 10ms.
T2 The device releases FS 'K' on the bus. However
by this time the 'K' state is held by downstream
port.
T1 + 1.0ms < T2 < T1 + 15ms
T3 Downstream port asserts SE0. T1 + 20ms
T4 Latest time at which a device, which was
previously in HS mode, must restore HS mode
after bus activity stops.
T3 + 1.33µs {2 Low-speed bit times}
Small Footprint Hi-Speed USB 2.0 Device PHY with UTMI Interface
Datasheet
SMSC USB3290 39 Revision 1.5 (11-02-07)
DATASHEET
8.12 Detection of Resume
Resume signaling always takes place in FS mode (TERMSELECT and XCVRSELECT = FS enabled),
so the behavior for a HS device is identical to that of a FS device. The SIE uses the LINESTATE
signals to determine when the USB transitions from the 'J' to the 'K' state and finally to the terminating
FS EOP (SE0 for 1.25us-1.5µs.).
The resume signaling (FS 'K') will be asserted for at least 20ms. At the beginning of this period the
SIE may negate SUSPENDN, allowing the transceiver (and its oscillator) to power up and stabilize.
The FS EOP condition is relatively short. SIEs that simply look for an SE0 condition to exit suspend
mode do not necessarily give the transceiver’s clock generator enough time to stabilize. It is
recommended that all SIE implementations key off the 'J' to 'K' transition for exiting suspend mode
(SUSPENDN = 1). And within 1.25µs after the transition to the SE0 state (low-speed EOP) the SIE
must enable normal operation, i.e. enter HS or FS mode depending on the mode the device was in
when it was suspended.
If the device was in FS mode: then the SIE leaves the FS terminations enabled. After the SE0 expires,
the downstream port will assert a J state for one low-speed bit time, and the bus will enter a FS Idle
state (maintained by the FS terminations).
If the device was in HS mode: then the SIE must switch to the FS terminations before the SE0 expires
( < 1.25µs). After the SE0 expires, the bus will then enter a HS IDLE state (maintained by the HS
terminations).
8.13 HS Device Attach
Figure 8.8 demonstrates the timing of the USB3290 control signals during a device attach event. When
a HS device is attached to an upstream port, power is asserted to the device and the device sets
XCVRSELECT and TERMSELECT to FS mode (time T1).
VBUS is the +5V power available on the USB cable. Device Reset in Figure 8.8 indicates that VBUS is
within normal operational range as defined in the USB 2.0 specification. The assertion of Device Reset
(T0) by the upstream port will initialize the device. By monitoring LINESTATE, the SIE state machine
knows to set the XCVRSELECT and TERMSELECT signals to FS mode (T1).
The standard FS technique of using a pull-up resistor on DP to signal the attach of a FS device is
employed. The SIE must then check the LINESTATE signals for SE0. If LINESTATE = SE0 is asserted
at time T2 then the upstream port is forcing the reset state to the device (i.e. Driven SE0). The device
will then reset itself before initiating the HS Detection Handshake protocol.
Small Footprint Hi-Speed USB 2.0 Device PHY with UTMI Interface
Datasheet
Revision 1.5 (11-02-07) 40 SMSC USB3290
DATASHEET
Figure 8.8 Device Attach Behavior
Table 8.10 Attach and Reset Timing Values
TIMING
PARAMETER DESCRIPTION VALUE
T0 Vbus Valid. 0 (reference)
T1 Maximum time from Vbus valid to when the device
must signal attach. T0 + 100ms < T1
T2
(HS Reset T0) Debounce interval. The device now enters the HS
Detection Handshake protocol. T1 + 100ms < T2
Small Footprint Hi-Speed USB 2.0 Device PHY with UTMI Interface
Datasheet
SMSC USB3290 41 Revision 1.5 (11-02-07)
DATASHEET
8.14 Application Diagram
Figure 8.9 USB3290 Application Diagram showing USB related signals
Opmode 0
Opmode 1
Xcvrselect 0
Termselect
SuspendM
Reset
Txvalid
Rxvalid
Rxerror
Rxactive
Linestate 1
Linestate 0
Txready
Clkout
USB3290
Data0
DP
DM
DP
DM
VBUS
Optional
Level Shifter
USB
Connector (B)
Data1
Data2
Data3
Data4
Data5
Data6
Data7
G3
F4
B1
C2
D1
E2
D2
C1
A7
F3
A6
F5
B7
C7
D6
D7
E6
E7
F7
G7
F1
E1
G5
G4
To VBUS
detect input
Small Footprint Hi-Speed USB 2.0 Device PHY with UTMI Interface
Datasheet
Revision 1.5 (11-02-07) 42 SMSC USB3290
DATASHEET
Figure 8.10 USB3290 Application Diagram showing power and miscellaneous signals
1M
3.3 Volt
Supply
B5
4.7uF
0.1uF
USB3290
VDDIO
G6 VDDIO
VDDA18
C6 VDD18
B3 VDD33
G1 VDD33
G2 VDD33
A5 VDD33
B2 GND
B6 GND
F2 GND
A2 REG_EN
B4
4.7uF
0.1uF
12.0k
A1 RBIAS
30pF*
30pF*
24 MHz
XTAL
A3
XI
A4
XO
4.7uF
0.1uF
F6 GND
Small Footprint Hi-Speed USB 2.0 Device PHY with UTMI Interface
Datasheet
Revision 1.5 (11-02-07) 43 SMSC USB3290
DATASHEET
Chapter 9 Package Outline
Figure 9.1 USB3290-FH 40 Ball, VFBGA Package Outline & Parameters 4x4x0.9mm Body, Lead-Free RoHS Compliant
Small Footprint Hi-Speed USB 2.0 Device PHY with UTMI Interface
Datasheet
Revision 1.5 (11-02-07) 44 SMSC USB3290
DATASHEET
Figure 9.2 BGA, 4x4 Taping Dimensions and Part Orientation
Small Footprint Hi-Speed USB 2.0 Device PHY with UTMI Interface
Datasheet
SMSC USB3290 45 Revision 1.5 (11-02-07)
DATASHEET
Figure 9.3 Reel Dimensions for 12mm Carrier Tape
Small Footprint Hi-Speed USB 2.0 Device PHY with UTMI Interface
Datasheet
Revision 1.5 (11-02-07) 46 SMSC USB3290
DATASHEET
Note: Standard reel size is 4000 pieces per reel.
Figure 9.4 Tape Length and Part Quantity
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Microchip:
USB3290-FH-TR

Navigation menu