NI R Series Multifunction RIO Specifications National Instruments 785 372492c

User Manual: R-785

Open the PDF directly: View PDF .
Page Count: 10

Download
Open PDF In Browser	View PDF

NI R Series Multifunction RIO
Specifications
This document lists the specifications of the NI 781xR/783xR/784xR/785xR. These specifications are typical at 25 °C unless
otherwise noted.

Français

Deutsch
ni.com/manuals

Analog Input (NI 783xR/784xR/785xR Only)
Input Characteristics
Number of channels
NI 7830R .................................... 4
NI 7831R/7833R/7841R/7842R/
7851R/7852R/7853R/7854R ...... 8

Input impedance
Powered on .................................10 GΩ in parallel with
100 pF
Powered off/overload..................4.0 kΩ min

Input modes..................................... DIFF, RSE, NRSE
(software-selectable;
selection applies to all
channels)

Input signal range ............................±10 V

Type of ADC .................................. Successive
approximation
Resolution ....................................... 16 bits, 1 in 65,536
Conversion time
NI 783xR/NI 784xR.................... 4 μs
NI 785xR .................................... 1 μs
Maximum sampling rate
NI 783xR/784xR......................... 200 kS/s (per channel)
NI 785xR .................................... 750 kS/s (per channel)

Input bias current
NI 783xR.....................................±2 nA
NI 784xR/785xR .........................±5 nA
Input offset current
NI 783xR.....................................±1 nA
NI 784xR/785xR .........................±5 nA
Input coupling .................................DC
Maximum working voltage
(signal + common mode).................Inputs should remain
within ±12 V of ground
Overvoltage protection
Powered on .................................±42 V
Powered off.................................±35 V

Accuracy Information
NI 783xR
Absolute Accuracy
Nominal Range (V)

Relative Accuracy

Noise +
Quantization (μV)

% of Reading

Positive
Full
Scale

Negative
Full
Scale

24
Hours

1 Year

Offset
(μV)

Single
Point

Averaged

Temp
Drift
(%/°C)

10.0

–10.0

0.0496

0.0507

2,542

1,779

165

0.0005

Absolute
Accuracy
at Full
Scale
(±mV)

Single
Point

Averaged

7.78

2,170

217

Resolution (μV)

Note: Accuracies are valid for measurements following an internal calibration. Averaged numbers assume dithering and
averaging of 100 single-channel readings. Measurement accuracies are listed for operational temperatures within ±1 °C of
internal calibration temperature and ±10 °C of external or factory-calibration temperature.
NI 784xR/785xR
Absolute Accuracy
Nominal Range (V)

Noise +
Quantization (μV)

% of Reading

Positive
Full
Scale

Negative
Full
Scale

24
Hours

10.0

–10.0

0.0186

Relative Accuracy

1 Year

Offset
(μV)

Single
Point

Averaged

Temp
Drift
(%/°C)

0.0228

1,591

1,029

91.6

0.0005

Absolute
Accuracy
at Full
Scale
(±mV)

Single
Point

Averaged

3.97

1,205

121

Resolution (μV)

Note: Accuracies are valid for measurements following an internal calibration. Averaged numbers assume dithering and
averaging of 100 single-channel readings. Measurement accuracies are listed for operational temperatures within ±1 °C of
internal calibration temperature and ±10 °C of external or factory-calibration temperature.

DC Transfer Characteristics

NI 784xR/785xR
Small signal (–3 dB) .............. 1 MHz

INL

Large signal (1% THD) ......... 500 kHz

NI 783xR.....................................±3 LSB typ, ±6 LSB max
NI 784xR/785xR .........................±1 LSB typ, ±3 LSB max

Settling Time

DNL
NI 783xR.....................................–1.0 to +2.0 LSB max
NI 784xR/785xR .........................±0.4 LSB typ,
±0.9 LSB max

Device

±16 LSB

±4 LSB

±2 LSB

NI 783xR

±20.0 V

7.5 μs

10.3 μs

40 μs

±2.0 V

2.7 μs

4.1 μs

5.1 μs

±0.2 V

1.7 μs

2.9 μs

3.6 μs

±20.0 V

2.1 μs

4.2 μs

8 μs

±2.0 V

1.3 μs

1.6 μs

1.8 μs

±0.2 V

0.8 μs

1.1 μs

1.2 μs

No missing codes
NI 783xR.....................................16 bits typ, 15 bits min
NI 784xR/785xR .........................16 bits guaranteed
NI 784xR/
785xR

CMRR, DC to 60 Hz .......................–86 dB

Dynamic Characteristics
Bandwidth
NI 783xR

Accuracy

Step
Size

Crosstalk ......................................... –80 dB, DC to 100 kHz

Small signal (–3 dB)...............650 kHz
Large signal (1% THD)..........55 kHz

NI R Series Multifunction RIO Specifications

2

ni.com

Analog Output (NI 783xR/784xR/785xR Only)
Output Characteristics
Output type ..................................... Single-ended,
voltage output

Resolution........................................16 bits, 1 in 65,536
Update time .....................................1.0 μs

Number of channels

Maximum update rate......................1 MS/s

NI 7830R .................................... 4

Type of DAC ...................................Enhanced R-2R

NI 7831R/7833R/7841R/7842R/
7851R/7852R/7853R/7854R ...... 8

Accuracy Information
Absolute Accuracy

Positive Full
Scale

Negative Full
Scale

24 Hours

1 Year

Offset (μV)

Temp Drift
(%/°C)

Absolute
Accuracy at
Full Scale
(mV)

10.0

–10.0

0.0335

0.0351

2366

0.0005

5.88

Nominal Range (V)

% of Reading

Note: Accuracies are valid for analog output following an internal calibration. Analog output accuracies are listed for
operation temperatures within ±1 °C of internal calibration temperature and ±10 °C of external or factory calibration
temperature. Temp Drift applies only if ambient is greater than ±10 °C of previous external calibration.

DC Transfer Characteristics

Dynamic Characteristics

INL.................................................. ±0.5 LSB typ,
±4.0 LSB max

Settling time
Accuracy

DNL ................................................ ±0.5 LSB typ,
±1 LSB max

Step Size

±16 LSB

±4 LSB

±2 LSB

Monotonicity................................... 16 bits, guaranteed

±20.0 V

6.0 μs

6.2 μs

7.2 μs

Voltage Output

±2.0 V

2.2 μs

2.9 μs

3.8 μs

Range .............................................. ±10 V

±0.2 V

1.5 μs

2.6 μs

3.6 μs

Output coupling .............................. DC
Slew rate ..........................................10 V/μs
Output impedance
NI 783xR .................................... 1.25 Ω

Noise................................................150 μVrms, DC to 1 MHz

NI 784xR/785xR......................... 0.5 Ω

Glitch energy
at midscale transition.......................±200 mV for 3 μs

Current drive ................................... ±2.5 mA
Protection ........................................ Short-circuit to ground
Power-on state................................. User configurable

© National Instruments Corporation

3

NI R Series Multifunction RIO Specifications

Digital I/O

Reconfigurable FPGA

Number of channels

NI 7811R/7830R/7831R

NI 781xR.....................................160

FPGA type.................................. Virtex-II V1000

NI 7830R.....................................56

Number of flip-flops................... 10,240

NI 7831R/7833R/7841R/7842R/
7851R/7852R/7853R/7854R ......96

Number of 4-input LUTs............ 10,240
Number of 18 × 18 multipliers ... 40
Embedded block RAM............... 720 kbits

Compatibility...................................TTL

NI 7813R/7833R

Digital logic levels

FPGA type.................................. Virtex-II V3000
Level

Min

Max

Number of flip-flops................... 28,672

Input low voltage (VIL)

0.0 V

0.8 V

Number of 4-input LUTs............ 28,672

Input high voltage (VIH)

2.0 V

5.5 V

Number of 18 × 18 multipliers ... 96

Output low voltage (VOL),
where IOUT = –4 mA

0V

0.4 V

Output high voltage (VOH),
where IOUT = 4 mA

2.4 V

3.3 V

Embedded block RAM............... 1,728 kbits
NI 7841R/7851R
FPGA type.................................. Virtex-5 LX30
Number of flip-flops................... 19,200
Number of 6-input LUTs............ 19,200
Number of DSP48
slices (25 × 18 multipliers)......... 32

Output current
Source .........................................4.0 mA

Embedded block RAM............... 1,152 kbits

Sink .............................................4.0 mA

NI 7842R/7852R

Input leakage current .......................±10 μA

FPGA type.................................. Virtex-5 LX50

Power-on state .................................Programmable, by line

Number of flip-flops................... 28,800

Protection

Number of 6-input LUTs............ 28,800
Number of DSP48
slices (25 × 18 multipliers)......... 48

Input
NI 781xR/783xR.....................–0.5 to 7.0 V, single line

Embedded block RAM............... 1,728 kbits

NI 784xR/785xR .................... –20.0 to 20.0 V, single line
Output .........................................Short-circuit
(up to eight lines may be
shorted at a time)

NI 7853R
FPGA type.................................. Virtex-5 LX85
Number of flip-flops................... 51,840

Minimum pulse width

Number of 6-input LUTs............ 51,840

Input ............................................25 ns

Number of DSP48
slices (25 × 18 multipliers)......... 48

Output .........................................12.5 ns

Embedded block RAM............... 3,456 kbits

Minimum sampling period ..............5 ns

NI 7854R
FPGA type.................................. Virtex-5 LX110
Number of flip-flops................... 69,120
Number of 6-input LUTs............ 69,120
Number of DSP48
slices (25 × 18 multipliers)......... 64
Embedded block RAM............... 4,608 kbits
Timebase......................................... 40, 80, 120, 160,
or 200 MHz

NI R Series Multifunction RIO Specifications

4

ni.com

Bus Interface

Timebase reference sources
NI PCI-781xR/783xR ................. Onboard clock only

PCI/PCIe/PXI ..................................Master, slave

NI PCIe-784xR/785xR ............... Onboard clock only

Data transfers...................................DMA, interrupts,
programmed I/O

NI PXI-78xxR............................. Onboard clock,
phase-locked to PXI
10 MHz clock

Number of DMA channels ..............3

Timebase accuracy,
onboard clock.................................. ±100 ppm, 250 ps
peak-to-peak jitter

Power Requirement
+5 VDC (±5%)1

Phase locked to PXI 10 MHz
Clock (NI PXI-78xxR only) ............ Adds 350 ps
peak-to-peak jitter

NI 781xR.....................................9 mA typ

Additional frequency-dependent peak-to-peak jitter

NI PXI-7841R/7851R .................125 mA typ

NI 7830R/7831R.........................330 mA typ
NI 7833R.....................................364 mA typ
NI PXI-7842R/7852R .................136 mA typ

NI 781xR/783xR
40 MHz .................................. None

NI 7853R.....................................460 mA typ

80 MHz .................................. 400 ps

NI 7854R.....................................484 mA typ

120 MHz ................................ 720 ps

+3.3 VDC (±5%)2

160 MHz ................................ 710 ps

NI 7811R.....................................650 mA typ

200 MHz ................................ 700 ps

NI 7813R.....................................850 mA typ

NI 784xR/785xR

NI 7830R/7831R.........................462 mA typ

40 MHz .................................. None

NI 7833R.....................................727 mA typ

80 MHz .................................. 460 ps

NI PCIe-7841R/7851R ...............847 mA typ

120 MHz ................................ 172 ps

NI PCIe-7842R/7852R ...............984 mA typ

160 MHz ................................ 172 ps

NI PXI-7841R/7851R .................525 mA typ

200 MHz ................................ 152 ps

NI PXI-7842R/7852R .................604 mA typ
NI 7853R.....................................640 mA typ

Calibration (NI 783xR/784xR/785xR Only)

NI 7854R.....................................843 mA typ

Recommended warm-up time ......... 15 minutes
+12 V
Calibration interval ......................... 1 year

NI 784xR/785xR .........................0.5 A

Onboard calibration reference

–12 V

DC level...................................... 5.000 V (±3.5 mV)
(actual value stored
in Flash memory)

NI PXI-784xR/785xR .................0.25 A
+5V terminal

Temperature coefficient ............. ±5 ppm/°C max

Connector 0.................................0.5 A max3

Long-term stability ..................... ±20 ppm/ 1,000 h

Connector 1.................................0.5 A max3
Connector 2.................................0.5 A max3

Note

Refer to Calibration Certificates at
ni.com/calibration to generate a calibration
certificate for the NI 78xxR.

1
2
3
4

All connectors .............................1.5 A max3, 4

Does not include current drawn from the +5 V line on the I/O connectors.
Does not include current sourced by the digital outputs.
(NI PCIe-78xxR only) Total maximum terminal current for all connectors is 100 mA unless disk drive connector is attached.
(NI 784xR/785xR only) The NI 784xR/785xR has a user-replaceable socketed fuse that opens when current exceeds the current
specification. Refer to the NI R Series Multifunction RIO User Manual, available at ni.com/manuals, for information about
fuse replacement.

© National Instruments Corporation

5

NI R Series Multifunction RIO Specifications

Environmental

To calculate the total current sourced by the digital outputs,
use the following equation:

The NI 78xxR is intended for indoor use only.

j

Operating Environment

 current sourced on channel i

NI 781xR......................................... 0 °C to 55 °C,
tested in accordance with
IEC-60068-2-1 and
IEC-60068-2-2.

i=1

Power available at I/O connectors...4.50 to 5.25 VDC at 1 A
total, 250 mA per I/O
connector pin

NI 7830R, NI 7831R
40 MHz or 80 MHz timebase ..... 0 °C to 55 °C,
tested in accordance with
IEC-60068-2-1 and
IEC-60068-2-2.

Physical
Dimensions (not including connectors)
NI PCI-781xR/783xR..................17 cm by 11 cm
(6.7 in. by 4.3 in.)

NI PCI/PXI-7833R

NI PCIe-784xR/785xR ................17 cm by 11 cm
(6.7 in. by 4.3 in.)

40 MHz timebase ....................... 0 °C to 55 °C,
tested in accordance with
IEC-60068-2-1 and
IEC-60068-2-2.

NI PXI-78xxR .............................16 cm by 10 cm
(6.3 in. by 3.9 in.)

80 MHz timebase ....................... 0 °C to 55 °C except the
following: 0 °C to 45 °C
when installed in an
NI PXI-1000/B or
NI PXI-101X,
tested in accordance with
IEC-60068-2-1 and
IEC-60068-2-2.

Weight
NI PCI-781xR/783xR..................112 g
NI PCIe-784xR/785xR ................127 g
NI PXI-78xxR .............................152 g
I/O connectors
NI 781xR.....................................Four 68-pin female
high-density VHDCI type

NI PXI-7841R/7842R/7851R/7852R/7853R/7854R

NI 7830R.....................................Two 68-pin female
high-density VHDCI type

40 MHz timebase ....................... 0 °C to 55 °C,
tested in accordance with
IEC-60068-2-1 and
IEC-60068-2-2.

NI 783xR/784xR/785xR..............Three 68-pin female
high-density VHDCI type
Disk drive power connector
(PCIe devices) .................................Standard ATX peripheral
connector (not serial
ATA)

80 MHz timebase ....................... 0 °C to 55 °C except the
following: 0 °C to 45 °C
when installed in an
NI PXI-1000/B or
NI PXI-101X,
tested in accordance with
IEC-60068-2-1 and
IEC-60068-2-2.

Maximum Working Voltage
(NI 783xR/784xR/785xR Only)
Maximum working voltage refers to the signal voltage plus the
common-mode voltage.

NI PCIe-7841R/7842R/7851R/7852R
40 MHz or 80 MHz timebase ..... 0 °C to 40 °C,
tested in accordance with
IEC-60068-2-1 and
IEC-60068-2-2.

Channel-to-earth ..............................±12 V, Measurement
Category I
Channel-to-channel .........................±24 V, Measurement
Category I

Relative humidity range.................. 10% to 90%,
noncondensing,
tested in accordance with
IEC-60068-2-56.

Caution Do not use the NI 783xR/784xR/785xR
for connection to signals in Measurement
Categories II, III, or IV.

Altitude ........................................... 2,000 m at 25 °C ambient
temperature

NI R Series Multifunction RIO Specifications

6

ni.com

Storage Environment

Safety

NI PCI/PXI-781xR/783xR .............. –20 °C to 70 °C,
tested in accordance with
IEC-60068-2-1 and
IEC-60068-2-2.

The NI 78xxR is designed to meet the requirements of the
following standards of safety for electrical equipment for
measurement, control, and laboratory use:
•

IEC 61010-1, EN 61010-1

NI PCIe-784xR/785xR .................... –20 °C to 70 °C,
tested in accordance with
IEC-60068-2-1 and
IEC-60068-2-2.

•

UL 61010-1, CSA 61010-1
Note For UL and other safety certifications,
refer to the product label or the Online Product
Certification section.

NI PXI-784xR/785xR ..................... –40 °C to 70 °C,
tested in accordance with
IEC-60068-2-1 and
IEC-60068-2-2.

Electromagnetic Compatibility
The NI 78xxR is designed to meet the requirements of the
following standards of EMC for electrical equipment for
measurement, control, and laboratory use:

Ambient temperature range ............ –20 °C to 70 °C,
tested in accordance with
IEC-60068-2-1 and
IEC-60068-2-2.
Relative humidity range.................. 5% to 95%,
noncondensing,
tested in accordance with
IEC-60068-2-56.

•

EN 61326 (IEC 61326): Class A emissions;
Basic immunity

•

EN 55011 (CISPR 11): Group 1, Class A emissions

•

AS/NZS CISPR 11: Group 1, Class A emissions

•

FCC 47 CFR Part 15B: Class A emissions

•

ICES-001: Class A emissions

Note Clean the device with a soft, non-metallic
brush. Make sure that the device is completely dry
and free from contaminants before returning it to
service.

Note For the standards applied to assess the EMC
of this product, refer to the Online Product
Certification section.
Note For EMC compliance, operate this device
with shielded cabling.

Shock and Vibration (for NI PXI-78xxR Only)
Operational shock ........................... 30 g peak, half-sine,
11 ms pulse;
tested in accordance with
IEC-60068-2-27. Test
profile developed in
accordance with
MIL-PRF-28800F.

CE Compliance
•

2006/95/EC; Low-Voltage Directive (safety)

Random vibration

•

2004/108/EC; Electromagnetic Compatibility Directive
(EMC)

This product meets the essential requirements of applicable
European Directives as follows:

Operating .................................... 5 Hz to 500 Hz, 0.3 grms
Nonoperating .............................. 5 Hz to 500 Hz, 2.4 grms,
tested in accordance with
IEC-60068-2-64.
Nonoperating test profile
exceeds the requirements
of MIL-PRF-28800F,
Class 3.

© National Instruments Corporation

7

NI R Series Multifunction RIO Specifications

Online Product Certification

Waste Electrical and Electronic Equipment (WEEE)
EU Customers At the end of their life cycle, all
products must be sent to a WEEE recycling center.
For more information about WEEE recycling
centers and National Instruments WEEE initiatives,
visit ni.com/environment/weee.htm.

Refer to the product Declaration of Conformity (DoC) for
additional regulatory compliance information. To obtain
product certifications and the DoC for this product, visit
ni.com/certification, search by model number or
product line, and click the appropriate link in the Certification
column.

⬉ᄤֵᙃѻક∵ᶧ᥻ࠊㅵ⧚ࡲ⊩ ˄Ё೑ RoHS˅

Environmental Management

Ё೑ᅶ᠋ National Instruments ヺড়Ё೑⬉ᄤֵ
ᙃѻકЁ䰤ࠊՓ⫼ᶤѯ᳝ᆇ⠽䋼ᣛҸ (RoHS)DŽ݇Ѣ
National Instruments Ё೑ RoHS ড়㾘ᗻֵᙃˈ
䇋ⱏᔩ ni.com/environment/rohs_chinaDŽ

NI is committed to designing and manufacturing products in
an environmentally responsible manner. NI recognizes that
eliminating certain hazardous substances from our products is
beneficial to the environment and to NI customers.

(For information about China RoHS compliance,
go to ni.com/environment/rohs_china.)

For additional environmental information, refer to the NI and
the Environment Web page at ni.com/environment. This
page contains the environmental regulations and directives
with which NI complies, as well as other environmental
information not included in this document.

NI R Series Multifunction RIO Specifications

8

ni.com

DIO35
DIO33
DIO31
DIO29
DIO27
DIO26
DIO25
DIO24
DIO23
DIO22
DIO21
DIO20
DIO19
DIO18
DIO17
DIO16
DIO15
DIO14
DIO13
DIO12
DIO11
DIO10
DIO9
DIO8
DIO7
DIO6
DIO5
DIO4
DIO3
DIO2
DIO1

34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1

DIO38
DIO36
DIO34
DIO32
DIO30
DIO28
+5V

TERMINAL 68

TERMINAL 35

TERMINAL 34

TERMINAL 1

DGND

TERMINAL 1

TERMINAL 34

DGND
DGND
DGND

TERMINAL 35

TERMINAL 68

TERMINAL 68

TERMINAL 35

TERMINAL 34

TERMINAL 1

TERMINAL 1

TERMINAL 34

TERMINAL 35

TERMINAL 68

+5V
DGND
DGND
DGND

DGND
DGND
DGND
DGND
DGND
DGND
DGND
DGND
DGND
DGND
DGND
DGND
DGND
DGND
DGND
DGND
DGND
DGND
DGND

CONNECTOR 1
(RDIO)

DIO0

68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35

CONNECTOR 2
(RDIO)

DIO39
DIO37

CONNECTOR 3
(RDIO)

CONNECTOR 0
(RDIO)

Device Pinouts

Figure 1. NI 781xR Connector Pin Assignments and Locations

© National Instruments Corporation

9

NI R Series Multifunction RIO Specifications

CONNECTOR 0
(RMIO)
DIO35
DIO33
DIO31
DIO29
DIO27
DIO26
DIO25
DIO24
DIO23
DIO22
DIO21
DIO20
DIO19
DIO18
DIO17
DIO16
DIO15
DIO14
DIO13
DIO12
DIO11
DIO10
DIO9
DIO8
DIO7
DIO6
DIO5
DIO4
DIO3
DIO2
DIO1

34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1

DIO38
DIO36
DIO34
DIO32
DIO30
DIO28
+5V

AI0+
AIGND0
AI1+
AI2+
AIGND2
AI3+
AI4+1

TERMINAL 68
TERMINAL 34

+5V
DGND
DGND

AIGND4
AI5+1
AI6+1

DGND
DGND

TERMINAL 1

AIGND6
AI7+1

DGND
DGND
DGND

TERMINAL 35

AISENSE
AO0
AO1

DGND
DGND
DGND

AO2
AO3
AO41
AO51
AO61

DGND
DGND
DGND
DGND
DGND
DGND
DGND

TERMINAL 68

TERMINAL 35

TERMINAL 34

TERMINAL 1

DGND
DGND
DGND
DGND
DGND
DGND
DGND
DGND
DGND

AO71
DIO15
DIO13
DIO11
DIO9

TERMINAL 1

TERMINAL 34

TERMINAL 35

TERMINAL 68

CONNECTOR 1
(RDIO)

DIO0

68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35

CONNECTOR 2
(RDIO)

DIO39
DIO37

DIO7
DIO6
DIO5
DIO4
DIO3
DIO2
DIO1
DIO0
+5V

68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35

34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1

AI0–
AIGND1
AI1–
AI2–
AIGND3
AI3–
AI4–1
AIGND5
AI5–1
AI6–1
AIGND7
AI7–1
No Connect
AOGND0
AOGND1
AOGND2
AOGND3
AOGND4
AOGND5
AOGND6
AOGND7
DIO14
DIO12
DIO10
DIO8
DGND
DGND
DGND
DGND
DGND
DGND
DGND
DGND
+5V

1 No Connect on the NI 7830R

Figure 2. NI 783xR/784xR/785xR Connector Pin Assignments and Locations

National Instruments, NI, ni.com, and LabVIEW are trademarks of National Instruments Corporation.
Refer to the Terms of Use section on ni.com/legal for more information about National
Instruments trademarks. Other product and company names mentioned herein are trademarks or trade
names of their respective companies. For patents covering National Instruments products/technology,
refer to the appropriate location: Help»Patents in your software, the patents.txt file on your
media, or the National Instruments Patent Notice at ni.com/patents.
© 2008–2009 National Instruments Corporation. All rights reserved.

372492C-01

Jun09



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Modify Date                     : 2016:05:09 16:31:10+02:00
Update Date                     : 2009-06-01
Section                         : Support
Date                            : 2009-06-01
Author                          : Technical Communications
Short Title                     : NI R Series Multifunction RIO Specifications
Content Format                  : manualStub
Ni Boosts                       : RV:3.20,RN:5,CR:5
Content Class                   : Technical
Language                        : en
Product Categories              : 10230,11614,11615,11616,11617,3775,4820,4821,5109,5110,5111,5194,5195,6646,6773,9702,9703,9704,9781,9782
Doc Status                      : current
Keywords                        : RIO, 7811, 7811R, 7813, 7813R, FPGA, R, Series, R-Series, 7830, 7830R, 7831, 7831R, 7833, 7833R, 7841, 7841R, 7842, 7842R, 7851, 7851R, 7852, 7852R, 7853, 7853R, 7854, 7854R, 372492
Create Date                     : 2009:06:16 10:28:47Z
Doc Type                        : other,specifications
Content Type                    : specifications
Manual Status                   : current
Nigen 1                         : c,2009
Nigen 3                         : 06
Nigen 2                         : 2009
Description                     : This document lists the specifications of the NI R Series Multifunction RIO devices. These specifications are typical at 25 °C unless otherwise noted. The following devices are included in this document: NI PCI-7811R, NI PXI-7811R, NI PCI-7813R, NI PXI-7813R, NI PCI-7830R, NI PXI-7830R, NI PCI-7831R, NI PXI-7831R, NI PCI-7833R, NI PXI-7833R, NI PCIe-7841R, NI PCIe-7842R, NI PCIe-7851R, NI PCIe-7852R, NI PXI-7841R, NI PXI-7842R, NI PXI-7851R, NI PXI-7852R, NI PXI-7853R, and NI PXI-7854R. For a Japanese language version of this document, go to ni.com/manuals.
Nigen 4                         : 372492c.pdf
Page Mode                       : UseOutlines
Page Layout                     : SinglePage
XMP Toolkit                     : Adobe XMP Core 5.1.0-jc003
Format                          : application/pdf
Producer                        : Acrobat Distiller 9.0.0 (Windows); modified using iText® 5.5.4 ©2000-2014 iText Group NV (AGPL-version)
Creator Tool                    : FrameMaker 8.0
Creator                         : Technical Communications
Subject                         : RIO 7811 7811R 7813 7813R FPGA R Series R-Series 7830 7830R 7831 7831R 7833 7833R 7841 7841R 7842 7842R 7851 7851R 7852 7852R 7853 7853R 7854 7854R 372492
Title                           : NI R Series Multifunction RIO Specifications - National Instruments
Has XFA                         : No
Page Count                      : 10
Signing Authority               : ARE Acrobat Product v8.0 P23 0002337
Annotation Usage Rights         : Create, Delete, Modify, Copy, Import, Export
Signing Date                    : 2009:06:23 14:39:46-05:00

EXIF Metadata provided by EXIF.tools