I2000 System Brochure
User Manual: i2000 System
Open the PDF directly: View PDF 
.
Page Count: 21
| Download | |
| Open PDF In Browser | View PDF |
Coil Cleaners Indoor Air Quality Total System Protection Refrigeration Oils Water Treatment Glycols Specialty Aerosols Insulation Products Specialty Products Plumbing Products Water Filtration Quality Products for Air Conditioning, Refrigeration & Heating Table of Contents 1-6 Nu-Brite® Foam-Brite® Alka-Brite® Plus TriClean 2x™ Cal-Brite® CalClean® Special HD CalClean® Tri-Pow’r® HD Evap-Fresh™ Cal-Green™ Evap-Green™ Green Clean Evap-Pow’r® Evap Foam No Rinse® Nu-Blast® Cal-Blast® Cal-Shield® Coil Gun® No. 50P Sprayer No. 100P Cal-Shield® Poly Sprayer No. 220CP Poly Sprayer No. 200P Poly Sprayer No. 300P Poly Sprayer Multi-Purpose Sprayer Nu-Calgon’s Coil Cleaner Selection Guide Indoor Air Quality 7 Evap-Fresh™ Bio-Fresh® cd Bio-Fresh® Fogger PanPads Pan-Treat® Gel Tabs Total System Protection 8-11 Rx11-flush® Rx11-flush® Liquid Rx11-flush® Accessories Rx-Acid Scavenger® Phase III® Refrigeration Oil Acid Test A/C Re-New A/C EasySeal & A/C EasySeal-SS A/C EasyDry Refrigeration Oil & Vacuum Pump Oil 12-13 Water Treatment Glycol, Closed Systems & Steam Boilers Freez-Kontr’l® Burst-Kontr’l® AP-100 Freez-Therm® Glycol Refractometer Glycol/Oil Transfer Pump Winter Treat® Ty-lon® B20 Ty-lon® B14A System Cleaner Aerosols Evap-Foam No Rinse® Nu-Brite® Evap-Fresh™ Cal-Blast® Nu-Blast® CalClean® Break-n-Lube™ Food-Grade Silicone V-Belt Dressing Pan-Spray® Pipe-Dri® Nu-Kill® II Wasp and Hornet Killer Pump Protector Zinc Rich Cold Galvanizing Spray-n-Bond™ Spray Adhesive Electrical Contact Cleaner Degreasing Solvent ef Insulation Products C-3s, C-4s, C-5s Refrigeration Oil Emkarate® RL Lubricant (POE) Polyvinyl Ether Lubricant (PVE) Zerol® Alkylbenzene Refrigeration Oil Total Lube Refrigeration Oil Test Kit Oil Refractometer CanVerter® Cal-Vac™ Vacuum Pump Oil Perma-Wrap™ Foam-Tite® Cork Tape Cork-Tite® Sealing and Caulking Cords Thumb-Tite® Nu-Foam® Water Treatment Quick Seal™ Repair Tapes Great Wipes Scrubs-In-A-Bucket® HVAC80 Quick Seal™ Pipe Repair Degreasing Solvent ef Pneu-flush® Thermo-Trap® Liquid Scale Dissolver Eco-Lyme Season Start® Vital Flo® No. 31-TX1 Acid Pump HK-31 Hose Kit Season Treat Ty-lon® C70 No. 340 Liquid Scale Inhibitor 14-17 14-17 No. 85 Algaecide No. 90 Bromicide Tablets Humidi-Treat™ pH-Treat™ Evap-Treat® Water Sample Bottles Cal-Treat® No. 233 No. 215 and No. 1075 Drip Feeders Jug Holders CMS III & CMS-IV Monitor Systems No. 20L and No. 100L Feeders Conductivity Meter Specialty Products Gas Leak Detectors Cal-Blue® Plus Gas Leak Detector Cal-Blue® LT Gas Leak Detector Gas Leak Detectors 25 Same Quality Products, Gas Leak Detector Fluorescent Gas Leak Detector Plumbing Products & Water Test Kits 18-19 20-21 Look for the new package labels on your favorite Nu-Calgon products. Water Filtration - Maintenance 27 Water Filtration 25 Water Filtration - NP Series 29 Nickel-Safe Ice Machine Cleaner Liquid Ice Machine Cleaner IMS-II Sanitizing Concentrate Ice Guard® AP & Mini Ice Guard® AP Micromet® Crystals 6R Micromet® CFS Filtration System The CTL Series Micro-Plus® & Micro-Carbon 4 NP Series Housings 6R Micromet®/Carbon Cartridge Carbon Block Cartridge Sediment Cartridge 6R Micromet® Cartridge 6R Micromet®/Sediment Cartridge NP Series Brackets Water Filtration Nu-Plus® by Everpure® Heads: 30-35 Nu-Brite® QL3B Head QC71 Heads Nu-Brite is the most effective coil cleaner available today. It foams, brightens, and is an equally effective yet safer alternative to HF acidbased products. It produces a high volume of foam that cleans more effectively than acids, particularly in removing grease. Biodegradable. The liquid versions are USDA approved and NSF registered. Systems: MRS-20 Reverse Osmosis System Kleensteam CT and Kleensteam II Highflow CSR Manifold with Prefilter Coldrink/Insurice Systems 22-23 23-24 18 ounce can 1 gallon bottle 2.5 gallon pail 55 gallon drum Cartridges: nu-i20002 and nu-i40002 nu-MC2 and nu-XC2 BH2 and OCS2 Cartridge OW200L and OW4Plus Cartridge 7CB5 and nu-7CB5-S 4CB5 and 4CB5-S Cartridge 7SO Softening Cartridge Nu-Plus CU and Nu-Plus CU-S The ultimate in foaming alkaline cleaners. It provides for excellent cleaning and brightening, and at the same time provides tremendous foaming to push dirt and grime out of the coil. Can easily be used in place of the more dangerous HF acid-based products. Biodegradable. NSF registered. 1 gallon bottle 2.5 gallon pail 55 gallon drum Other Filtration Products: 4178-08 4178-05 4178-01 Alka-Brite® Plus A non-acid, alkaline based product for brightening and cleaning air cooled condensers. It contains the best available detergents to quickly penetrate and remove oxidation, and its foaming action helps to lift greasy soils out of the coil. Biodegradable. NSF registered. New Filtration Technology: 7S1, 7FC, and 7CLM Cartridges Claris Cartridges Nu-Calgon Training Seminars 4291-18 4291-08 4291-05 4291-01 Foam-Brite® Nu-Plus 10˝ and 20˝ Coarse Prefilters Nu-Plus EC110 and EC210 SRX Scale Inhibitor Feeder Nu-Plus IMF-7 and IMF-10 4JT Flushing/Sanitizing Cartridge ScaleKleen™ Scale Remover 25 Brand New Look. 26 Vital Flo® Calci-Solve Drain Solve UrinaKleen Complete Test Kit Nitrite Test Kit No. 89A Test Kit Organic Phosphonate Test Kit Coil Cleaners Coil Cleaners and Sprayers 36 1 gallon bottle 55 gallon drum 4120-08 4120-01 Visit us at www.nucalgon.com or call 1-800-554-5499 1 Coil Cleaners Coil Cleaners Tri-Pow’r® HD An outstanding general purpose coil cleaner, providing detergency and degreasing as well as deodorizing capability. Its positive emulsion technology is very effective against oily grime as it converts the deposits into a more fluid or liquid form that can be easily rinsed away. It is nonacid, non-toxic, and biodegradable. NSF registered. NEW 1 gallon bottle 55 gallon drum 4371-88 4371-81 Evap-Fresh™ Evaporator Coil Cleaner & Disinfectant Evap-Fresh is a ready-to-use, no rinse cleaner and disinfectant for evaporator coils. It effectively cleans as well as kills mold and bacteria. This one-step no rinse disinfectant cleaner is perfect for air conditioners, commercial air handling units, HVAC cooling coils, refrigeration equipment, and evaporator coils. EPA registered specifically for use on HVAC equipment. TriClean 2x™ The new way to clean a condenser coil. Simply connect to hose, clean, and rinse. TriClean 2x is metal-safe, designed for rapid emulsion of soils from the coil. Restores efficiency and is ideal for painted fin and microchannel coils. 1 quart sprayer with hose connector 4166-75 4166-08 4372-24 The following products are part of Nu-Calgon’s Environmentally Friendly Green Select line. They have been recognized by the EPA’s Design for the Environment program, which tests and identifies products that are safer for the environment. Cal-Brite® Cal-Brite is a low pH cleaner developed for cleaning evaporator coils, air-cooled condensers and other finned cooling and heating coils. It’s versatility is based upon glycolic acid and other unique ingredients. It provides moderate foaming and brightening and is safe for use indoors as well as outdoors. It’s particularly suitable when lime scale must be removed from outdoor coils. 1 gallon bottle 55 gallon drum 18 ounce can 1 gallon bottle 4133-08 4133-01 Cal-Green™ Condenser Cleaner Cal-Green is a plant-based, natural condenser cleaner that is powerful enough to remove dirt, grease, and grime but environmentally safe for use around people, plants, animals, and aquatic life. This non-foaming, non-toxic concentrate is perfect for cleaning residential or commercial systems and restores their efficiency while being environmentally responsible. 1 gallon bottle 55 gallon drum 4190-08 4190-01 CalClean® An alkaline detergent formulated for cleaning evaporator coils, air-cooled condenser coils, metal filters, fan blades, and other surfaces soiled with grease, dust and dirt. Biodegradable. USDA approved Aerosol is NSF registered. 20 ounce can 1 gallon bottle 2.5 gallon pail 55 gallon drum Evap-Green is a no rinse product is perfect for numerous heating and air conditioning applications such as evaporator coils, roof top units, window units, metal filters, fan blades, and more. By using Evap-Green, a natural plant based formulation, the coil is being cleaned with the most environmentally friendly product available. It is also safe to be used around people, plants, animals, and aquatic life. 1 gallon bottle 55 gallon drum 4191-08 4191-01 Special HD CalClean® Green Clean The best non-foaming cleaner available. Specifically formulated to remove tobacco tars from electronic air cleaners as well as the most stubborn deposits from finned coils. USDA approved. A pleasantly scented, all-purpose, environmental friendly cleaner designed for the rapid removal of grease and other heavy soils. It can be used right out of the bottle or diluted for milder jobs. Biodegradable. 1 gallon bottle 2.5 gallon pail 55 gallon drum 2 4081-75 4135-08 4135-06 4135-01 Evap-Green™ Evaporator Cleaner 4143-08 4143-06 4143-01 1 quart spray bottle 1 gallon bottle 55 gallon drum 4186-24 4186-08 4186-01 Visit us at www.nucalgon.com or call 1-800-554-5499 3 Coil Cleaners Coil Cleaners Coil Cleaners Sprayers Coil Gun® A different approach to coil cleaning - a “hose-end” sprayer that features 5 different mix ratio settings designed for coil cleaners. Utilizes a 2 quart capacity bottle and includes a foam wand as well as “quick disconnect” capability. Evap Pow’r®-C A no rinse product formulated for cleaning evaporator coils. It is metal-safe, and it cleans and emulsifies even the most stubborn soils and deposits. Biodegradable. USDA approved. 1 gallon bottle 2.5 gallon pail 55 gallon drum 4168-08 4168-05 4168-01 1 each 4774-0 Sprayers Coil Cleaners No. 50P Poly Sprayer The No. 50P is constructed of high-density translucent polyethylene. It has a half gallon (3 pint) capacity. The nozzle is adjustable and the flow rate is controlled by a thumb lever. It comes with a 7˝ polyethylene pump. 1 each 4770-0 Evap Foam No Rinse® Evap Foam No Rinse is a high performing, heavy duty detergent. It is formulated with special surfactants and alkaline cleaners that have been developed into a foaming, no rinse product. Evap Foam is ideal for use on most coils, but it is particularly suited for use on cooling or evaporator coils. The aerosol can be sprayed either right side up or upside down. NSF registered. 18 ounce can 4171-75 No. 100P Cal-Shield® Poly Sprayer This sprayer is constructed of high-density translucent polyethylene. It has a funnel top for easy chemical pouring and a 1 gallon working capacity. It comes with a 8˝ polypropylene pump, brass handle and extension tube with adjustable nozzle, a wear-resistant hose, and a pressure relief valve. It is highly recommended that this sprayer be dedicated to Cal-Shield applications. 1 each 4770-2 Nu-Blast® A no rinse condenser coil cleaner in a convenient aerosol package. Double action of high pressure blast and solvent cleaning restores design efficiency of condenser coils. It is non-flammable and non-conductive. No rinse required - cleaning solvent evaporates completely. Use with adequate ventilation. 18 ounce can The No. 220CP Poly Sprayer is constructed of high-density translucent polyethylene with a funnel-top that provides easy chemical pouring. This 2 gallon capacity sprayer features an easy fill level indicator and comes with an 8˝ pump and a high resin plastic adjustable nozzle with three feet of hose. 1 each 4771-3 4290-75 No. 200P Poly Sprayer, Water Pressurizing NEW The No. 200P Poly Sprayer is constructed of high-density translucent polyethylene. It has a 2 gallon working capacity, funnel top, pump handle, and equipped with all-brass hardware. No pumping is required. Pressurize the sprayer with water through a “quick disconnect” fitting. Cal-Blast® Cal-Blast is a no rinse condenser cleaner that will powerfully separate undesirable materials from the surface, offering maximum cleaning of finned coils. It’s a high performance aerosol with excellent solvency and blasting spray. 20 ounce can 4132-20 1 each 4771-2 No. 300P Poly Sprayer The No. 300P Poly Sprayer is constructed of high-density translucent polyethylene. It has a funneltop and a 3.5 gallon capacity (3 gallon working capacity). It comes with a 10˝ Celcon pump, brass extension tube with adjustable nozzle, and five feet of vinyl hose. 1 each 4772-0 Cal-Shield® Cal-Shield is a synergistic liquid formulation based upon DuPont’s Teflon® fluoro-additives. It’s designed for application on air-cooled condensers, evaporator coils, and other finned heating and cooling coils. Cal-Shield will shield and protect the coil from adverse conditions. 1 quart spray bottle 1 gallon bottle 55 gallon drum 4 4148-32 4148-08 4148-01 Multi-Purpose Sprayer A 24 ounce capacity sprayer. It is ideal for small cleaning jobs, such as window units and water coolers. 1 each 4768-W3 Visit us at www.nucalgon.com or call 1-800-554-5499 5 Replacement parts are available for all Nu-Calgon sprayers. Contact your local wholesaler. No. 220CP Poly Sprayer ECO-FRIENDLY CAL-GREEN 4 CAL-BLAST CAL-SHIELD BIO-FRESH CD 4 4 GREEN CLEAN 4 Evap-Fresh is a ready-to-use, no rinse cleaner and disinfectant for evaporator coils. It effectively cleans as well as kills mold and bacteria. This one-step no rinse disinfectant cleaner is perfect for air conditioners, commercial air handling units, HVAC cooling coils, refrigeration equipment, and evaporator coils. EPA registered specifically for use on HVAC equipment to kill H1N1 and other viruses such as Norwalk, Rhoto, Hepatitis, Rabies MRSA, and more. 18 ounce can 1 gallon bottle 4166-75 4166-08 Bio-Fresh® cd A ready-to-use bacteriostatic, fungistatic, and deodorizer based upon chlorine dioxide technology. Inhibits the growth of bacteria, mold, mildew, fungi, and yeasts in IAQ applications, and is safe for fogging and may be applied to occupied space. It’s EPA registration includes application to HVACR ventilating equipment, including coils, condensate pans, filters, and duct-work. Applies easily by spraying, brushing, sponging, wiping, or fogging. EPA registered. 1 quart spray bottle 1 gallon bottle 4126-34 4126-38 TRI-POW’R HD 4 4 EVAP-FRESH 4 4 4 4 4 4 4 4 AEROSOL EVAP-FRESH 4 4 EVAP FOAM NO RINSE 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4* 4* 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4* 4 4 4 4 4 4 4 4 4 4 4 FEATURES & BENEFITS 4 4 4 4 4 4 4 4 4 4 Foaming Brightening Degreasing Disinfectant Non-Rinsing Coil Protection Biodegradable USDA Authorized EPA Registered 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 Greasy Dirt & Oil Cooking Grease Dirt & Grime Tobacco Tars Lint, Dust Oxide (Corrosion) Deposits Cottonwood/ Bugs 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 FORMULATED TO REMOVE 4 4 4 4 4 Product Type Alkaline Alkaline Alkaline Alkaline Alkaline Alkaline Alkaline Acidic Alkaline Alkaline Alkaline Alkaline Bacteriostat Alkaline Protectant Solvent Solvent Alkaline Alkaline 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 Condenser Coils Evaporator Coils Permanent Filters Electronic Air Filters Small Condenser Coils Small Evaporator Coils Fan Blades, Motors, Etc. 4 4 4 4 4 EQUIPMENT USED ON 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 ECO-FRIENDLY EVAP-GREEN NU-BLAST CALCLEAN AEROSOL CALCLEAN CALCLEAN SPECIAL HD CAL-BRITE ALKA-BRITE PLUS FOAM-BRITE NU-BRITE 6 Evap-Fresh™ Evaporator Coil Cleaner & Disinfectant Bio-Fresh® Fogger The Bio-Fresh Fogger is made of a one-piece, seamless heavy-duty copolymer. It uses a 48˝ flexible hose and is adjustable from 0-18 ounces per minute with the respective particle size at 20 to 80 microns. It’s ideal for fogging Bio-Fresh cd in duct work and large areas. 1 each EVAP POW’R Coil Cleaner Selection Guide * Dilution ratios for no rinse applications: Tri-Pow’r HD= 10:1, CalClean Special HD= 40:1, CalClean= 10:1 Indoor Air Quality 4693-0 PanPads A product formulated to eliminate the build-up of bacteria and slime growths in air conditioning and refrigeration condensate drain pans. In laboratory tests, it has been proven effective against a wide spectrum of harmful bacteria, including Legionella. All sizes will provide adequate treatment for up to 6 months and the product is EPA registered for this application. NSF registered. 5 (up to 5 tons) 4295-34 5 Slim (up to 5 tons) 4295-36 15 (up to 15 tons) 45 (up to 45 tons) 4296-24 4296-45 Pan-Treat® Pan-Treat condensate tablets control odors and prevent overflows caused by plugged condensate drain lines. They can also be used in humidifiers. They are very easy to use, as well as safe, non-corrosive, non-toxic, and biodegradable. 1 bottle (200 tablets) 4296-60 Gel Tabs - Condensate Drain Pan Treatment Formulated with a breakthrough technology for treating air conditioning drain pans and lines. Keeps the drain pan from clogging and eliminates foul and musty odors. When activated by condensation, the tablet will turn to gel and lock into place. Dissolves continuously and completely with nothing left to remove for up to 3 months. Stack together to increase duration. 3 ton tab (12 in tube) 4185-03 5 ton tab (6 in tube) 4185-05 15 ton tab each 20 ton tab each Visit us at www.nucalgon.com or call 1-800-554-5499 4185-15 4185-20 7 Indoor Air Quality Nu-Calgon’s Coil Cleaner Selection Guide Total System Protection Total System Protection Endorsed by York®, Goodman®, Nordyne®, Coleman®, and Daikin® Rx11-flush® R x11-flush is a unique solvent engineered specifically for flushing refrigeration and air conditioning systems. R x11-flush is ozone-safe, non-toxic, and non-flammable. Used exactly like the old R-11 flushing process, its patented HFC based solvent formulation is powerful enough to flush away sludge, carbon residues, oils, acids, water and other particulate. R x11-flush is ideal for system flushing after burnouts, during retrofits and for flushing line sets for R-410A conversions. R x11-flush has been the industry’s standard for over a decade and contractors agree, it’s the best flush for R-410A retrofits and after compressor burnouts. Benefits of R x11-flush • • • • • Optimal Boiling point enhances complete evacuation of flush No oily residue left behind Safe, nontoxic, and nonflammable Formulated with patented solvent technology Approved as part of the U.S. EPA’s Significant New Alternatives Policy (SNAP) Program • Over a decade of proven success • Convenient pressurized package size NEW Rx11-flush® Liquid R x11-flush Liquid is a new and improved chemistry that is the next generation in flushing technology. It remains a constant boiling solvent and is now stronger, faster acting and dissolves more oil, moisture and contaminants than any other flush. It is ideal for line sets, burnouts and other flushing requirements. 19.5 ounce can Rx11-flush Liquid Starter Kit 4300-30 4300-38 Amount of R x11-flush Needed • Up to 1/2˝ tubing: Use a 20-30 second burst of R x11-flush through each line for every 50 feet. For the 13 and 26 pound cylinders, use a 7-10 second burst. • Up to 7/8˝ tubing: Use a 60-90 second burst of R x11-flush through each line for every 50 feet. For the 13 and 26 pound cylinders, use a 20-30 second burst. Oil load, line configuration, etc. will impact how much flush is needed. Rx11-flush® Accessories Rx11-flush Starter Kit 1 lb. canister 2+1 Display Pack 2 lb. canister 13 lb. canister 26 lb. canister Contains a 1 lb. canister, Rx11-flush Gun and Hose, and Injection Valve Recommended for a 3-4 ton system. Contains one Injection Valve and two 2 lb. canisters Recommended for a 5-7 ton system Recommended for up to 50 ton system Recommended for systems over 50 tons 4300-08 4300-09 4300-10 4300-11 4300-15 4300-26 The R x11-flush product family also includes various support tools. This includes the Injection Valve for hooking up to a charging hose for flushing and the Flushing Tool for facilitating line set flushing. In addition, the R x11-flush Gun with a built-in flushing attachment and the R x11-flush Hose (24˝) are available. Flushing Tool Rx11-flush Gun Rx11-flush Hose (24˝) Injection Valve 4300-50 4300-51 4300-52 4300-89 (Injection Valve fits Pneu-flush® , A/C Re-New, and pressurized Rx-Acid Scavenger as well) 8 Visit us at www.nucalgon.com or call 1-800-554-5499 9 Total System Protection Total System Protection Total System Protection Total System Protection NEW Rx-Acid Scavenger® The most effective way to neutralize or “scavenge” acid in refrigeration, air conditioning systems. It is perfect for use after burnouts or during normal on-going system maintenance. In addition, the Rx-Acid Scavenger can be used with all lubricants: mineral, alkylbenzene and polyol ester. Now available in a pressurized can for easy injection into charged systems or hermetically sealed systems. 2 fluid ounce unpressurized bottle 3.8 ounce pressurized can Injection Valve A/C EasySeal 4301-02 4301-05 NEW 4300-89 A/C EasySeal prevents and seals refrigerant leaks in residential and light commercial ACR systems. It is perfect for those hard-to-find and expensive-to-fix leaks and works with all refrigerants (except ammonia). It is easily installed with the reusable piercing valve and hose. A/C EasySeal circulates with the system’s refrigerant, and if a leak should occur, it will quickly seal the leak and prevent the system from losing refrigerant and shutting down. (Injection Valve fits Rx11-flush, Pneu-flush® , and A/C Re-New as well) Phase III® Refrigeration Oil Acid Test Kit Formulated for use with POEs as well as mineral oils and alkylbenzene. An inexpensive, disposable test kit that provides proof-positive that acid level in refrigeration oil is safe or unsafe. Phase separation makes it easy to see change in color of acid indicator (even if a leak detection dye has been added to the oil). Just two bottles to work with, it is simple, safe, accurate, and small enough that you can carry several in your tool box. 1 each 4320-W8 2. Completely fill the small bottle with oil from the unit being tested. Do this immediately after the oil is removed from the crankcase since exposure to air will contaminate the oil and give a false test result. How long will A/C EasySeal remain in a system? Indefinitely or until the system’s refrigerant is removed. 5. If the bottom layer: Stays purple- the oil is satisfactory. Turns light pink or looses color completelythe oil is contaminated. 3. Pour the oil into the large bottle and shake well. Good Oil Bad Oil A/C Re-New A/C Re-New is a highly formulated product that has established an outstanding track record enhancing the performance of air conditioning and refrigeration systems. A/C Re-New quiets noisy compressors, reduces energy consumption by lowering starting and running amps, and improves heat transfer in the evaporator and condenser. It’s great for new and old systems. Visit www.acrenew.com for more information. 4057-50 4057-52 4057-54 4057-55 4057-99 4300-89 4050-06 4050-01 4050-02 4051-99 Fixed Leak Once in the system, how does A/C EasySeal behave? It travels with the refrigerant, behaving much like a vapor or mist. 4. Wait two to three minutes. A phase separation will develop as the oil rises to the top of the mixture and an aqueous layer forms on the bottom. 6 ounce pressurized can “2+1” Display Pack 1 quart can 4 fluid ounce can A/C Re-New Injector Tool - for 4 ounce can Injection Valve 3 ounce pressurized can - treats 1.5 to 5 ton systems 1.25 ounce pressurized can - treats fractional to 1.5 ton systems 2 cans of A/C EasySeal and an A/C Piercing Valve and Hose Frequently Asked Questions How to Test Oil with Phase III 1. Pour the solution from the small bottle into the large bottle. The bottom layer of this mixture will be purple. A/C EasySeal A/C EasySeal-SS “2+1” Display Pack A/C Piercing Valve and Hose How much A/C EasySeal should I use? Generally, one can of A/C EasySeal should be used in 1.5 to 5 ton systems. A/C EasySeal-SS should be used in small fractional horsepower systems under 1.5 tons or 18,000 Btu/h and can also be used to seal leaks in automotive A/C systems. Ultimately, the size of the leak, not the system’s tonnage, will determine how much sealant is needed. How large of a refrigerant leak will A/C EasySeal repair? Generally, if the system doesn’t leak its entire charge in 7 days, A/C EasySeal will repair it. How does A/C EasySeal work? It is activated by moisture or air, both of which will exist at a leak. Once activated, it forms a permanent epoxy-like seal at the site of the leak. Its behavior is similar to blood clotting to form a scab. What if there is moisture in the system? At industry accepted levels of moisture*, A/C EasySeal will not react within the system due to the very low amount of moisture in circulation. A/C EasySeal is designed to react at higher levels of moisture saturation (relative humidity) found at a leak site, not at sparse moisture levels found in most systems. If moisture is suspected or determined to be above these accepted levels, use A/C EasyDry 20 minutes prior to addressing the leak with A/C EasySeal. * For POE lubricant systems: <100 ppm For mineral/alkylbenzene lubricant systems: <50 ppm A/C EasyDry This product is a quick and simple way to prevent and eliminate moisture in a system. A/C EasyDry contains a dehydrating agent that converts system moisture into a natural organic material that is compatible with and mixes with the lubricant. It is great for preventing acid formation which is caused by moisture in a system and works with all refrigerants (except ammonia). Each can will treat up to a 5 ton system and is easily installed with the reusable piercing valve and hose. 3 ounce pressurized can A/C Piercing Valve and Hose 4051-06 4051-99 (Injection Valve fits Pneu-flush®, Rx11-flush® , and Rx-Acid Scavenger as well) 10 Visit us at www.nucalgon.com or call 1-800-554-5499 11 Total System Protection Total System Protection Refrigeration Oil & Vacuum Pump Oil Alkylbenzene Oil Zerol® Alkylbenzene Refrigeration Oil Zerol Refrigeration Oil is recommended for use in all refrigeration and air conditioning applications using CFC and HCFC refrigerants. It is highly recommended by refrigerant and compressor manufacturers for use with R-22 and other HCFC blends such as R-409A as it provides many distinct advantages: excellent miscibility, excellent thermal stability, low temperature performance compatibility with mineral oils. It is the oil of choice for R-22 and R-502. Zerol 150 200TD 300 400CA 500 Emkarate® RL Lubricant Viscosity 150 SUS 200 SUS 300 SUS 400 SUS 500 SUS 1 Gallon 4310-07 4308-07 4311-07 The Emkarate family of polyol ester refrigeration lubricants are designed specifically for use with HFC refrigerants. They are available in a range of viscosities. They have excellent thermal and chemical stability, and are compatible with a wide range of elastomers, polymeric materials, and other materials of construction. Fully miscible and compatible with mineral oils and alkylbenzene lubricants as well as with CFCs, HCFCs and HFCs. Emkarate RL 22H 32H 32HB 32-3MAF 46H 68H 68HB 68HP 100E 170H 220H+ 220XL Viscosity 100 SUS 150 SUS 150 SUS 150 SUS 200 SUS 300 SUS 300 SUS 300 SUS 500 SUS 850 SUS 1100 SUS 1100 SUS 1 Quart 4314-44 4314-64 4316-44 1 Gallon 4313-46 4314-46 4314-66 4315-46 4316-46 4316-86 4316-76 4317-66 4318-26 4318-66 5 Gallon 53 Gallon 4314-45 4314-62 4314-65 4314-41 4314-67 4315-41 4316-41 4316-45 4316-85 Mineral Oil C-3s, C-4s, C-5s Refrigeration Oil These are mineral naphthenic lubricants manufactured by Calumet Lubricant Company and available in three viscosities. They are specifically designed for today’s high performance air conditioning and refrigeration compressors using CFC and HCFC refrigerants. These compressors run at higher speeds and generate higher temperatures, and as a result, they require better lubrication. Use of these oils will ensure continued efficient operation, providing the important properties required from an efficient refrigeration oil. Nu-Calgon C-3s C-4s C-5s Viscosity 150 SUS 300 SUS 500 SUS 1 Gallon 4303-07 4304-07 4305-07 5 Gallon 4303-05 4304-05 55 Gallon 4303-01 4304-01 4305-01 Polyvinyl Ether (PVE) Lubricant 55 Gallon 4310-01 4308-01 4311-01 Vacuum Pump Oil Cal-Vac™ Vacuum Pump Oil Nu-Calgon’s Vacuum Pump Oil is a quality, high-grade lubricant that performs at the deepest vacuum. It has a very low vapor pressure and it has excellent lubricity for complete surface protection. It contains no additives or detergents. 1 pint bottle 1 quart bottle 1 gallon bottle 4316-71 4317-61 4318-21 4318-61 4318-25 4318-65 4318-75 5 Gallon 4310-05 4308-05 4311-05 4311-65 4312-05 4383-34 4383-24 4383-07 Refrigeration Oil Products Total Lube Refrigeration Oil Test Kit Have a professional lab analyze the oil to help detect potential problems such as metal wear or burnouts. The analysis will provide information on the oil’s moisture, total acid number, viscosity, color, and spectrochemical analysis on 20 plus metals and compounds. Help prevent potential downtime, burnouts, and costly oil changes by incorporating regular testing of the refrigeration oil. 1 each 4996-0 Oil Refractometer A precision optical instrument that allows for the rapid and accurate determination of the refractive index of oil solutions. It will specifically assist in determining the percent residual of oil remaining in a refrigeration system when converting it to a new refrigeration oil. Such retrofits require converting the mineral oil to a polyol ester (POE) or polyalkylene glycol (PAG), an alkylbenzene lubricant (Zerol®) to a POE, or a mineral oil to an alkylbenzene. 1 each 4815-0 Idemitsu Polyvinyl Ether Lubricant PVE lubricants provide for increased stability and lubrication. They do not hydrolyze in the presence of moisture, a very important feature in HVAC/R applications. Additionally, they are compatible with other refrigeration oils and process fluids. PVE lubricants also exhibit compatibility and performance with frequently used anti-wear additives. Idemitsu FVC32D FVC68D 12 Viscosity 32 SUS 68 SUS 1 Quart 4319-14 4319-24 1 Gallon 4319-16 4319-26 CanVerter® A hand-held pump used to remove or add oil to hermetic compressors. Easy to use; each stroke pumps 1 ounce of oil. 1 each 4814-0 Visit us at www.nucalgon.com or call 1-800-554-5499 13 Refrigeration Oil & Vacuum Pump Oil Polyol Ester (POE) Lubricant Water Treatment Neutralized Competitive Product with Dangerous Foam Working Strength Nu-Calgon Low-Foaming Liquid Scale Dissolver Water Heater Scale Removal Vital Flo® Tankless Water Heater Descaler Kit NEW The Vital Flo Tankless Water Heater Descaler Kit is a complete service tool for descaling tankless water heaters. It consists of a submersible descaler pump, a set of five foot 3/4˝ female hose threaded assemblies, formulated descaler solution packaged in a lidded four gallon chemical resistant container. The solution is also available separately. NSF registered. Vital Flo Kit Vital Flo Descaler Solution pH Color Indicator Nu-Calgon’s exclusive “built-in” pH color indicator tells you when to add more acid, and it lets you see when the system is clean. At working strength, the acid cleaning solution is green or light blue. When the acid solution is neutralized and is no longer working, the solution turns purple and more acid must then be added. The system is clean when the green color is retained for 20-45 minutes. 4387-01 4387-02 Feeding Equipment Low-Foaming Performance To demonstrate its greater low-foam property, Liquid Scale Dissolver was added to a beaker containing lime scale. A leading competitive liquid product was added to another beaker containing an equal amount of lime scale. See the difference! When cleaning towers and evaporator condensers, low-foam is the preferred approach as high foam is dangerous to both personnel and surroundings. No. 31-TX1 Acid Pump Compact submersible pump designed for circulating strong acids and cleaning solutions. All parts are constructed of acid-resistant materials. 1 each 4603-0 HK-31 Hose Kit An accessory item available for use with the No. 31-TX Acid Pump. Kit includes two 1/2 inch tubing adapters, two 10 foot sections of 1/2 inch clear plastic tubing and three hose clamps. 1 each 4604-0 Liquid Scale Dissolver Scale Prevention A hydrochloric (muriatic) acid formulated to remove calcium scales from cooling towers and other water-cooled equipment. It contains low-foaming corrosion inhibitors and a built-in pH color indicator to let you know when the acid has been neutralized. pH test paper is also included. USDA approved. 1 gallon bottle 5 gallon pail 2.5 gallon pail Season Treat ( 6R Micromet®) This patented Micromet® Plate product is contained in a unique flow-through package. The package design makes it simple to treat small cooling towers and evaporative condensers. Simply unwrap the package and place it in the sump. One canister treats up to 10 tons for scale (5 tons for corrosion) for 5 to 6 months. 4330-08 4330-05 4330-03 1 canister Eco-Lyme® NEW Eco-Lyme is a new chemistry for the HVAC/R market that provides a unique blend of performance with a desired eco-profile. The product is specially formulated to achieve descaling behavior of competing hydrochloric acid based chemistry descalers. However, the active ingredient is substantially safer on equipment metals. Eco-Lyme is ideal for stainless steel construction to eliminate potential issues of localized corrosion/pitting caused by repeated use of hydrochloric acid. Eco-Lyme is odorless; making it safer to use in the field. NSF registered. 1 gallon bottle 5 gallon pail 55 gallon drum Ty-Ion® C70 An all-organic liquid scale, deposit, and corrosion inhibitor for use in open recirculating cooling water systems, evaporative condensers, and air washer systems. This treatment program is particularly effective in preventing scale deposits in systems which utilize make-up water with high scaling potentials. 5 gallon pail 15 gallon pail 4167-08 4167-05 4167-01 An extremely concentrated scale inhibitor that is effective in hard, highly alkaline water. It is very stable and does not form any sludge. It is most effective at treatment levels between 10 and 15 parts per million. A constant, accurate feed is accomplished with a Drip Feeder or CMS Feed Pump. USDA approved. A powdered sulfamic acid formulation that contains the best inhibitors available for protecting all metals including galvanized metal. It is the best and the safest dry acid cleaner available. It contains a built-in pH color indicator to let you know when the acid solution has been neutralized as well as wetting and anti-foaming agents. USDA approved. 4360-88 4360-84 1 gallon bottle 5 gallon pail 55 gallon drum 4340-08 4340-05 4340-01 To Inhibit Scale Formation Initial Dosage Recommendation 14 7597-05 7597-P3 No. 340 Liquid Scale Inhibitor Season Start® “Imperial Grade” Scale Remover 10 lb. container 50 lb. pail 4364-88 Tons of Refrigeration or Horsepower Containers of Season Treat Tylon C70 Required per Month No. 340 Liquid Scale Inhibitor Required per Month Bleed-off for Most Scale-forming Waters 10 1 1/4 gallon 1/4 gallon 1/8 gpm 30 3 2/3 gallon 1/2 gallon 1/3 gpm Tons of Horsepower Liquid Scale Dissolver Eco-Lyme Season Start 10 2 gallons 4 gallons 10 lbs. 50 5 1 gallon 3/4 gallon 1/2 gpm 30 5 gallons 10 gallons 30 lbs. 100 --- 2 gallons 1 1/2 gallons 1 gpm 50 10 gallons 20 gallons 50 lbs. 120 --- 2 1/2 gallons 2 gallons 1 1/4 gpm 90 15 gallons 30 gallons 75 lbs. 150 --- 3 gallons 2 1/2 gallons 1 1/2 gpm Visit us at www.nucalgon.com or call 1-800-554-5499 15 Water Treatment Scale Removal Water Treatment Other Water Treatment Products Cal-Treat® No. 233 Evap-Treat® A liquid formulation that is used for controlling severe corrosion in evaporative condensers and cooling tower systems. It is based upon a synergistic formulation of zinc, molybdate, and organic phosphonate. Provides superior corrosion control and inhibits scale accumulation. Used in evaporative coolers or “swamp coolers” to prevent scale and corrosion. Place it in the cooler sump and it will last all season long, thereby increasing pad life. Utilizes 6R Micromet®, a food-grade NSF-certified polyphosphate. 5 gallon pail 4149-05 1 each (coolers up to 6,500 cfm) 1 each (coolers up to 10,000 cfm) 4173-04 4173-06 To Control Corrosion Cal-Treat No. 233 Required per Month Bleed-off for Most Corrosive Waters Capacity of System in Tons of Horsepower 1/3 gallon 1/10 gpm 10 1 gallon 1/4 gpm 30 2 gallons 3/8 gpm 50 3 gallons 1/2 gpm 90 Algae Prevention No. 85 Algaecide No. 85 Algaecide is a polymeric, cationic biocide that has been developed for controlling biological growth in equipment. It is an EPA-registered product to kill algae, bacteria, and fungi in recirculating water systems, industrial air washing systems, and closed systems. 1 gallon bottle 4108-08 The proper way to treat a cooling tower, closed loop system, or ice machine is to have the supply or makeup water tested. Nu-Calgon provides this valuable service for free and will return a full analysis of how to effectively treat the water in the system. These bottles can also be used to send in glycol samples to test its freeze point. 1 each (3 bottles) 4995-0 No. 215 and No. 1075 Drip Feeders Used for feeding No. 340 Liquid Scale Inhibitor, Cal-Treat 233, Ty-Ion C70 and No. 85 Algaecide. Calibrated at the factory to ensure accurate feeding. Provides the benefits of continuous treatment for small systems without the high cost usually associated with automatic feeding equipment. No. 215 Drip Feeder No. 1075 Drip Feeder 4669-W3 4670-W3 No. 90 Bromicide Tablets Jug Holders A chlorine-bromine donating organic compound in tablet form. It slowly releases powerful oxidizing hypohalous acids which prevent algae and slime bacteria fouling in open recirculating cooling water systems and evaporative coolers. It also has the capability of breaking up and removing existing biological mass from system surfaces. USDA approved and EPA-registered. These should be used when drip feeding any of Nu-Calgon’s liquid water treatment products. Once secured to the cooling tower or evaporative condenser, they will hold the 1 or 5 gallon containers in the proper position. 50 lb. pail 4109-M9 Tons of Refrigeration or Horsepower Gallons of No. 85 Algaecide per Month Number of No. 90 Bromicide Tablets for an Average System 10 1/6 gallon 5 30 1/3 gallon 15 50 1/2 gallon 25 90 2/3 gallon 45 Other Water Treatment Products Humidi-Treat™ Humidi-Treat is designed for humidifiers using up to 25 gallons per day and will inhibit scale for one season. Install Humidi-Treat on the water line that supplies water directly to the humidifier. 1 each 1 gallon holder 5 gallon holder 4606-0 4607-0 CMS III and CMS-IV Cooling Tower Monitor System To Kill Algae or Slime Growth For monitoring conditions in cooling towers and evaporative condensers. Provides subsequent bleed-off and chemical feed. It features a combination monitor and pump engineered into one-piece digital equipment. Complete system includes a solenoid valve. CMS III CMS IV 4608-0 4608-4 No. 20L and No. 100L Feeders Steel tanks suitable for pressures up to 150 psi and temperatures up to 212º F. Uses 3/4 inch FNPT connections for installing on bypass to any size line. Use No. 20L Feeder for initial charges up to 20 pounds (or 2 gallons). Use No. 100L Feeder for initial charges up to 100 pounds (or 10 gallons). Inlet/outlet strainers not included. No. 20L Feeder No. 100L Feeder 4628-0 4650-0 4190-02 pH-Treat™ Conductivity Meter pH-Treat is an in-line treatment product specific for the treatment of the acidic nature of the condensate water produced by today’s high efficiency furnaces. Includes fitting kit for easy installation. A hand held conductivity meter with built-in cell and automatic temperature compensation. It has an easy to read digital meter (in micromhos, 0-10,000) and dual point calibrations. 1 each 16 Water Sample Bottles 4720-06 1 each 4812-0 Visit us at www.nucalgon.com or call 1-800-554-5499 17 Water Treatment Corrosion Prevention Glycol Glycol Refractometer An instrument to determine the freeze protection level of ethylene or propylene glycol solutions. 1 each NEW 4816-0 Glycol/ Oil Transfer Pump Heavy-duty pump designed to transfer Freez-Kontr’l®, Freez-Therm®, or oil products (up to 1000 sus) from Nu-Calgon supplied 55 gallon drums to their application. 1 each 4817-0 Closed Systems & Steam Boilers Freez-Kontr’l® An expanded family of heat transfer fluids (anti-freeze) based upon non-toxic propylene glycol. All products are fully formulated to provide optimum freeze protection as well as corrosion protection in chilled water, hydronic and other closed systems. Safe to use where contact with potable water is possible. (GRAS certified- generally regarded as safe.) • Freez-Kontr’l - provides greater than -10 º F freeze protection and greater than -100 º F burst protection • Freez-Kontr’l 95/5 - a fully concentrated (~100%), inhibited propylene glycol product • Freez-Kontr’l 35 - formulated with 35% propylene glycol for use as a secondary coolant in supermarket rack applications • Freez-Kontr’l FG - a certified USP, food grade propylene glycol product at ~100% concentration. Inhibited. NSF registered. Freez-Kontr’l Freez-Kontr’l 95/5 Freez-Kontr’l 35 Freez-Kontr’l FG 1 gallon bottle 5 gallon pail 55 gallon drum 5 gallon pail 55 gallon drum 55 gallon drum 55 gallon drum 4188-07 4188-05 4188-02 4188-06 NEW 4188-03 NEW 4188-35 NEW 4188-04 NEW Winter Treat® Multi-treatment product for hot water and steam heating boilers and other closed water systems. It emulsifies and cleans away rust, corrosion deposits sludge, as well as inhibits system corrosion, foaming, surging, and lime scale. Typical use is one quart per 25 gallons of water. 1 quart bottle 1 gallon bottle 4390-32 4390-08 Ty-lon® B20 A liquid nitrite-borax corrosion inhibitor and dispersant for closed recirculating systems. It combines corrosion inhibitors, a unique copolymer dispersant, and a color indicator to facilitate leak detection, into a complete treatment for hot and chilled water closed systems containing ferrous and non-ferrous metal components. 5 gallon pail 7537-05 Burst-Kontr’l® AP-100 A specially formulated propylene glycol heat transfer solution for use in boilers having aluminum heat exchangers. It has corrosion inhibitors to protect aluminum, copper, solder, brass, and steel as well. Provides burst protection to -100 º F and freeze protection to -60 º F. 5 gallon pail 4187-15 Ethylene Glycol Ty-lon® B14A An all-in-one boiler treatment product that controls scale, corrosion, and condensate line corrosion in low pressure, low make-up steam heating boilers where 90% or more of the condensate is returned. It is chromate-free and contains a color indicator for visual determination of treatment residual. Its balanced formulation provides an energy efficient way of heating. 5 gallon pail 7519-05 Freez-Therm® An inhibited heat transfer fluid and anti-freeze based upon ethylene glycol. It can be used in chilled water, hydronic, and other closed systems for both freeze point suppression and corrosion inhibition. An uninhibited version is also available in drums on special order. 1 gallon bottle 5 gallon pail 55 gallon drum 55 gallon drum (uninhibited) 18 4189-07 4189-05 4189-01 4189-02 System Cleaner A liquid, heavy-duty industrial alkaline cleaner specifically formulated to emulsify and clean equipment surfaces and pipe fouled by cutting oils, grease, lubricants, corrosion products, and other debris. 5 gallon pail 4370-08 Visit us at www.nucalgon.com or call 1-800-554-5499 19 Closed Systems & Steam Boilers Glycol Equipment Propylene Glycol Aerosol Products Evap Foam No Rinse® Pan-Spray® Evap Foam No Rinse is a high performing, heavy duty detergent. It is formulated with special surfactants and alkaline cleaners that have been developed into a foaming, no rinse product. Evap Foam is ideal for use on most coils, but it is particularly suited for use on cooling or evaporator coils. The aerosol can be sprayed either right side up or upside down. NSF registered. Pan-Spray is an effective, easy-to-use water proof rubberized coating that won’t chip, flake, or peel. It’s ideal for sealing out rust and corrosion as well as repairing leaky condensate pans, cooling towers, swamp coolers, roofing, gutters, and down spouts. Pan Spray is the perfect solution for emergency and permanent repair. 18 ounce can 16 ounce can - White 16 ounce can - Black 4171-75 4296-50 4296-51 Nu-Brite® Evap-Fresh™ Pipe-Dri® Nu-Kill® II Wasp and Hornet Killer Nu-Brite is a very effective degreaser and cleaner on condenser coils. Its high foaming characteristic will help push soil deposits out of the coil, leaving it clean and bright. With proper ventilation, it can also be used as a kitchen degreaser by emulsifying stubborn, resistive grease deposits found on coils located in kitchens. Product should be used where adequate rinsing is possible. Evap-Fresh is a ready-to-use, no rinse cleaner and disinfectant for evaporator coils. It effectively cleans as well as kills mold and bacteria. This one-step no rinse disinfectant cleaner is perfect for air conditioners, commercial air handling units, HVAC cooling coils, refrigeration equipment, and evaporator coils. EPA registered specifically for use on HVAC equipment. Aerosol insulation which provides a moisture barrier to stop sweating and dripping on refrigeration lines, air conditioning lines, and other cold surfaces. Quickly adheres and dries to a hard water proof coating. PipeDri makes it possible to insulate hard to reach areas. A “quick-kill” spray formulation EPA registered to instantly and effectively kills wasps, hornets, and yellow jackets, from distances up to 20 feet. Nu-Kill II kills with residual action as wasps and hornets return to their nest. The formula is safe in and around electrical equipment, having a dielectric strength of 47,000 volts. 18 ounce can NEW Aerosol Specialty Products 4291-18 18 ounce can 4166-75 18 ounce can 4297-75 13.5 ounce can 4292-75 Cal-Blast® Nu-Blast® Pump Protector Zinc Rich Cold Galvanizing Cal-Blast is a no rinse condenser cleaner that will powerfully separate undesirable materials from the surface, offering maximum cleaning of finned coils. It’s a high performance aerosol with excellent solvency and blasting spray. A no rinse condenser coil cleaner in a convenient aerosol package. Double action of high pressure blast and solvent cleaning restores design efficiency of condenser coils. It is non-flammable and nonconductive. No rinse required - cleaning solvent evaporates completely. Use with adequate ventilation. When corrosion occurs in close-tolerance areas, it can cause the impeller to stick or bind. Pump Protector protects seasonally operated pumps against corrosion during shutdowns by winterizing them. It is safe for all types of water pumps and requires no special rinsing at start-up. Highly resistant to nearly all forms of corrosion. Perfect for repairing factory galvanized material damaged in shipment, welding, assembly, etc. Its 95% pure zinc film fuses itself to iron, steel, or aluminum. Blends well with hot-dip coating. Meets or exceeds Military Specifications MIL-P- 26915A, MIL-T- 26433, MIL-P- 21035, MIL-P-46105 and the Preece Test. 20 ounce can 4132-20 18 ounce can 4290-75 10 ounce can 4299-T8 14 ounce can Aerosol Lubricants 4087-03 Aerosol Adhesives CalClean® Break-n-Lube™ Spray-n-Bond™ Spray Adhesive CalClean is a heavy duty detergent formulation of surfactants, grease solvents, alkaline cleaners, corrosion inhibitors, and water conditioners. Ideal for cleaning window units as well as small evaporator coils, air cooled condenser coils, metal filters, fan blades and other surfaces soiled with greasy dust and dirt. NSF registered. This advanced technology 4-in-1 product is made with CERFLON® for high performance in a non-drying penetrating lubricant. It’s highly versatile with the ability to penetrate, lubricate, displace moisture, and provide superior resistance to corrosion. It’s especially formulated to help free rusted parts and assemblies. A wide web spray adhesive formulated specifically for insulation and duct liner applications. Ideal for porous surfaces, it is waterproof, flexible, transparent, non-staining, and it can be used for both temporary or permanent bonds. Formulated with the environment in mind, it contains no chlorinated solvents or ozone depleters, and it is voc-compliant in states such as California. Spray Adhesive is a fast-drying, all-purpose product that provides a strong, water-resistant, flexible bond. It is translucent and does not penetrate or soak material causing bleed-through. Spray Adhesive is excellent for labeling, bonding, splicing and sealing paper, cardboard, cloth, rubber, styrofoam, canvas, leather, wood, and most plastics. 20 ounce can 4081-75 12 ounce can 4128-03 12 ounce can 4369-75 14 ounce can 4080-04 Aerosol Industrial Products Food-Grade Silicone V-Belt Dressing Electrical Contact Cleaner Degreasing Solvent ef Food Grade Silicone sprays a perfect non-stick surface on ice machine surfaces, vending machines, coin slots, slicing machines, dairy machinery, and other food processing and packaging equipment. An excellent lubricant that prevents binding and sticking. Contains ingredients approved by the FDA for food contact use. USDA approved. V-Belt Dressing is specially formulated to penetrate and extend modern V-Belt life. It is particularly effective in maintaining V-Belt efficiency and performance under today’s increasing performance requirements. It keeps belts pliable, prevents slippage, and does away with squealing and chattering. USDA approved. Cleans, lubricates, and protects electrical contacts from corrosion, and is safe on most plastics. Cleaning action quickly removes greases, dust, and oxidation, restores and maintains precision and efficiency to the instrument and component. Includes extension tube for pinpointing application. USDA approved. A degreasing solvent, specially formulated for cleaning and degreasing equipment where washing or flushing is not possible. Simply spray on and wipe off. Penetrates quick and deep, loosening and liquefying heavy greases and tar. Non-corrosive and non-staining with a dielectric strength over 26,000 volts. 11 ounce can 4084-03 16 ounce can 4086-03 11 ounce can 11 once can - LV * * LV = Low VOC for California 20 4082-03 4082-04 17 ounce can 17 ounce can - LV* 4083-75 4083-83 * LV = Low VOC for California Visit us at www.nucalgon.com or call 1-800-554-5499 21 Aerosol Products Aerosol Coil Cleaners Insulation Products Insulation Products Sealing and Caulking Cords Sealing and Caulking Cords are nonstaining sealers formulated from the highest quality raw materials. They are water-resistant, dust-resistant and white in color. In addition, they securely adhere to most surfaces and provide excellent insulation value. They are available in 3/8˝ preshaped extruded cords, with serrated release paper. Perma-Wrap™ Foam Insulation Tape Formulated from the highest quality elastomeric thermal insulation material, and is manufactured to meet the needs of today’s air conditioning and refrigeration applications. Its closed cell construction seals out air and moisture, slowing down heat transfer and providing complete insulation. Used on hot or cold water pipes, chilled water, and refrigerant lines to prevent sweating and condensation. Service temperatures as low as -20º F with a high continuous temperature of 160º F and a high intermittent temperatures of 220º F. 2˝ x 1/8˝ x 30´ roll 2˝ x 1/8˝ x 30´ roll - Dispenser Package 3/8˝ x 25´ roll 4216-27 Thumb-Tite® This compound is formulated and manufactured for use in many sealing, insulating, and general maintenance applications. It has excellent adhesion capability and is non-staining, non-hardening, and unaffected by wide variations in temperature - an excellent thumbing grade. It is packaged in 2 pound boxes, each box contains two one pound bars. 4218-W3 4218-12 2 lb. box 4216-92 Nu-Foam® Nu-Foam is an expanding polyurethane prepolymer foam. It is used as a sealant and insulating product on openings created for refrigeration, air conditioning and heating tubes or pipes, duct joints, and other areas where unwanted air penetration might occur. Contains no CFCs nor any HCFCs, and is UL classified and fire retardant. Foam-Tite™ An economically priced tape formulated from quality thermal insulation material. It utilizes closed cell construction and can be used on cold water pipes, chilled water lines and refrigerant lines to prevent sweating and condensation. It can also be used on hot water lines, for better insulation against heat loss. Service temperatures of -15º F to 160 º F. 2˝ x 1/8˝ x 30´ roll 4293-04 4293-75 4219-12 Specialty Products NEW Cork Tape Formulated and manufactured for the air conditioning and refrigeration industry, it meets and exceeds specifications as an insulating material for preventing sweating and condensation on refrigerant lines, cold pipes, and other commercial refrigeration and a/c systems. Also serves as an excellent insulator on hot pipes, and used as a gasketing material, a sound-deadening material, and for wrapping valves, tees, and fittings. Service at temperatures as low as -30º F, as high as 200º F and won’t sag up to 350º F. 2˝ x 1/8˝ x 30´ roll 9 ounce can 20 ounce can 4217-W3 Quick Seal™ Repair Tapes Easy-to-use repair tapes, utilizing Micro Sealant™ Technology that will fuse between any two surfaces (except silicone) Will never harden, crack, peel, or fall off. These tapes can be used in a multitude of applications. Double-Sided Putty Tape - 2˝ x 4´ Roll Alumi-Tape - 3˝ x 25´ Roll Black Roof Repair Tape - 3˝ x 25´ Roll White Roof Repair Tape - 3˝ x 25´ Roll Web Tape - 3˝ x 25´ Roll 4299-20 4299-21 4299-22 4299-23 4299-24 Cork-Tite™ Designed for all types of climates, insulating cold pipes for all kinds of air conditioners in cars, homes, freezers, and refrigerators. Helps stop condensation problems and is ideal for retarding heat gain in cold pipes and preventing heat loss in hot pipes. An effective sound dampening material, it can also be used for gasketing purposes, sticks to all kinds of dry metals and seals tightly without drying. It is flexible and does not shrink or melt within the service temperature of -20º F to +200º F. 2˝ x 1/8˝ x 30´ roll 22 4217-12 Visit us at www.nucalgon.com or call 1-800-554-5499 23 Insulation Products/ Specialty Products Insulation Products Specialty Products NEW Gas Leak Detectors Great Wipes Great Wipes Industrial Strength Hand Towels are waterless wipes made specifically for the air conditioning, refrigeration, and plumbing service technician. Each premoistened, heavy duty towel has strong pumice scrubbing power that conveniently cleans anywhere and anytime. 75 count canister 4185-75 Cal-Blue® Plus Gas Leak Detector Cal-Blue Plus is a complete gas leak detector, freeze protected to 5˚F. Its high viscosity formula enables it to remain in contact with the applied surface for an extended period of time, allowing it to detect the smallest of leaks. It is also non-corrosive to metal, and it will not affect ultraviolet or black lights. Scrubs-In-A-Bucket® HVAC80 The original Scrubs. Disposable, pumice-performance waterless hand cleaner towels that effectively and quickly clean hands on a wide variety of industrial soils and greases. Each selfdispensing portable canister contains 80 perforated disposable heavy-duty towels and are pre-moistened with the famous Scrubs cleaning formulation. Effective yet gentle to the skin. Use anywhere, anyplace, anytime. 30 count canister 80 count canister HVAC80 6 ounce bottle with dauber 1 quart spray bottle 1 gallon bottle 4182-53 4182-24 4182-08 4366-24 4366-87 Quick Seal™ Pipe Repair A permanent knitted fiberglass impregnated tape that is designed for quick, in-the-field repair of leaks for all types of pipes. It can be used on both cold or hot water as well as refrigeration, plumbing, industrial, commercial, and residential applications. It is safe for potable water and is UL listed. ANSI/NSF Standard 61. 2˝ x 3´ wrap 4˝ x 12´ wrap Cal-Blue® LT Gas Leak Detector 4299-10 4299-11 The same high quality formulation as regular Cal-Blue Plus, but has added freeze-protection to -20˚F. It is the ideal detector for geographical areas that may experience very cold temperatures. Degreasing Solvent ef A degreasing solvent that is ozone-safe and environmentally friendly. It is a volatile solvent that provides effective degreasing and cleaning as well as controlled drying with absolutely no residue. It has a dielectric strength in excess of 26,000 volts. 1 gallon 1 gallon - LV* 4183-24 4183-08 4162-07 4162-17 Gas Leak Detector * LV = Low VOC for California Pneu-flush® A flushing and cleaning system specifically designed for pneumatic control air lines. It utilizes DuPont® Vertrel® XM, a premier ozone-safe HFC cleaning solvent. Pneu-Flush works quickly and easily to clean and purge the compressed air lines in HVAC control and other pneumatic systems. 2 lb. canister Injection Valve 1 quart spray bottle 1 gallon bottle The original industry leak detector. A high viscosity liquid that forms bubbles when daubed on a gas leak. Non-corrosive, non-staining, harmless to skin. Detects any type of gas leak such as air, compressed air, carbon dioxide, nitrogen, natural gas, and refrigerant gases. Freezeprotection to -20˚F. Six ounce plastic bottles have dauber in cap. USDA approved. 6 ounce bottle with dauber 4180-53 4298-01 4300-89 (Injection Valve fits Rx11-flush®, A/C Re-New, and Pressurized Rx-Acid Scavenger as well) Fluorescent Gas Leak Detector Thermo-Trap® The industry’s original heat absorbing paste designed to isolate heat encountered in soldering, welding, and brazing, thereby preventing damage to nearby heat sensitive controls, or fittings. USDA approved. Biodegradable. Available in paste as well as a gel. Thermo-Trap Paste Thermo-Trap Gel Thermo-Trap Gel 24 11 ounce tube 1 quart spray bottle 4 fluid ounce spray bottle 4371-36 4371-32 4371-53 A fluorescent formulation that provides improved visibility and long lasting bubbles. It is non-corrosive to metals and is freeze protected to 5˚F. Suitable for high and low temperature applications. Can be used for most refrigerants, natural gas and oxygen systems. USDA approved. 8 ounce bottle with dauber 1 quart spray bottle 1 gallon bottle 4184-53 4184-24 4184-08 Visit us at www.nucalgon.com or call 1-800-554-5499 25 Gas Leak Detectors Specialty Products Plumbing Products & Water Test Kits NEW Vital Flo® Tankless Water Heater Descaler Kit Nickel-Safe Ice Machine Cleaner The Vital Flo Tankless Water Heater Descaler Kit is a complete service tool for descaling tankless water heaters. It consists of a submersible descaler pump, a set of five foot 3/4˝ female hose threaded assemblies, formulated descaler solution packaged in a lidded four gallon chemical resistant container. The solution is also available separately. NSF registered. The original Nickel-Safe Ice Machine Cleaner. It is a food-grade citric-phosphoric acid product for removing scale deposits from ice machines having nickel-plated or tin-plated evaporators, and it is acceptable for use in all ice machines containing nickel. It mixes to form a green solution which makes rinsing easier. USDA approved. Vital Flo Kit Vital Flo Descaler Solution 4387-01 4387-02 16 fluid ounce bottle 1 gallon bottle 4287-34 4287-08 Calci-Solve Liquid Ice Machine Cleaner Remove scale from lines and clear clogged drains easily and effectively with Calci-Solve. The product includes a special inhibitor that coats the inside of the pipes with a protective film, allowing the acid in Calci-Solve to quickly dissolve calcium, magnesium, sodium, lime, rust, and other elements without harming pipes. Liquid Ice Machine Cleaner is a food-grade phosphoric acid that is fast acting, yet safe to use. It has been formulated to remove scale deposits from ice machines and coffee urns. It does not give off any harsh fumes or contain chlorine or chlorides that would attack stainless steel. USDA approved. 1 quart 1 gallon 4134-24 4134-08 8 fluid ounce bottle 1 gallon bottle 4207-47 4207-08 Drain Solve IMS-II Sanitizing Concentrate Ideal for condensate pan drains. Drain Solve saves time and money with its ease of use. It eliminates application concerns associated with more reactive, fuming drain openers. Simply pour it down the drain and let it work without fear of noxious fumes or reactions that may squirt corrosive chemicals into the face and eyes. Does not contain sulfuric acid. IMS-II is an EPA-registered sanitizing concentrate formulated to sanitize hard, non-porous surfaces and to eliminate odors and slime growths. No rinsing is required when diluted to 1.6 ounces per gallon. Formulated for general use in ice machines, ice cream dispensing equipment, and other food processing equipment. 1 quart 1 gallon 16 fluid ounce bottle 4165-24 4165-08 4211-34 Ice Guard® AP UrinaKleen Keep urinals free flowing with UrinaKleen. Use it to dissolve urinary salts, mineral scale, and rust deposits which are found in urinals. It also attacks the primary source of odors. 1 quart 1 gallon 4590-24 4590-08 Water Test Kits Complete Test Kit Nitrite Test Kit The complete test kit for cooling water and boiler water application testing. In addition to pH, this kit also provides tests for obtaining alkalinity, nitrite, hardness, and sulfite, and chloride levels. Used for testing treatment residual of Ty-Ion B20 and Ty-Ion B14A. It is a cerric ammonium nitrate (can) titration method, and it can be used in systems containing glycol. Each drop equals 40 ppm of nitrite. 1 each W017-0 1 each 4797-0 No. 89A Test Kit Organic Phosphonate Test Kit No. 89A Test Kit contains tests for determining hardness, pH, chloride and alkalinity, as well as treatment residual tests for Ty-Ion C70, Cal-Treat 233, No. 340 Liquid Scale Inhibitor, and Ty-Ion B20. Used to determine the treatment residual of No. 340 Liquid Scale Inhibitor, Ty-Ion C70, and Cal-Treat 233. 1 each 4798-2 1 each 4804-0 Ice Guard AP contains advanced nano-titanium technology formulated to inhibit the growth of a wide variety of slime-forming bacteria and algae found in ice machines. Ice Guard AP provides 3-6 months protection for machines up to 1200 lbs. of ice per day. Mini Ice Guard AP that is designed to fit in machines with smaller sumps. It provides 3-4 months protection in machines up to 400 lbs. of ice per day. Ice Guard® AP Mini Ice Guard® AP Micromet® Crystals This treatment has been used for more than 60 years to prevent scale formation in commercial and residential water systems. A typical initial charge for ice makers is 1 ounce for every 100 pounds of ice per day. Each month 25% of the initial charge should be added. USDA approved. NSF registered. 5 lb. container 50 lb. pail 4243-97 4243-84 6R Micromet® Food-grade phosphate specifically formulated for inhibiting scale in ice machines and other equipment using low volumes of water. It is used in Nu-Calgon scale controlling cartridges and requires replacement once every 6 months. Typical dosage is 8 ounces per 500 pounds of ice (50 gallons of water) a day. USDA approved. NSF registered. 51 lb. pail 26 4209-06 4209-05 4265-84 Visit us at www.nucalgon.com or call 1-800-554-5499 27 Water Filtration - Maintenance Water Filtration - Maintenance Plumbing Products Water Filtration Water Filtration - NP Series NP Series Housings These housings are designed to hold one of the NP Cartridges used to filter water for ice machines, coffee urns, and other beverage equipment. The NP24DD and NP48DD Housings can be charged with specific “NP24” or “NP48” cartridges for controlling scale, sediment, or objectionable tastes and odors. The NP24DD is equipped with 3/8˝ FPT connections and handles up to 4.0 gpm. The NP48DD is equipped with 1/2˝ FPT connections and can handle flow rates up to 5.0 gpm. NEW NP24DD NP48DD 6R Micromet®/Carbon Cartridge CFS Filtration System A custom cartridge, combining 6R Micromet for scale-control and a carbon block for sediment (10 microns), taste and odor control. A family of replacement cartridges and manifolds designed to service existing CUNO® CFS installations. A cost-effective water filtration system for food service applications: ice machines, fountain beverages, steam ovens, and drinking water. These systems offer manifold and sanitary quick change cartridges to fit the existing CUNO CFS brand installations and can also support new filtration installations. Nu-Plus CFS is the reliable choice for water filtration to prevent unwanted troubles caused by sediment, scale, or taste & odor existing in CUNO installations. Sediment – 5 Micron Sediment – 5 Micron / Phosphate Carbon Block - .5 Micron Carbon Block - .5 Micron / Phosphate Single Head Twin Head Triple Head Twin Series 4623-10 4623-11 4623-12 4623-13 NP24PC NP48PC The NP24C Cartridge fits the NP24DD Housing while the NP48C fits the NP48DD. These carbon blocks will remove most objectionable tastes and odors and are rated to remove particulate to 10 microns. NP24C NP48C CTL 220 C0070 Primary Cartridge Prefilter The NP24S (5˝) and the NP48S (10˝) are made from FDA-approved polypropylene construction and filter to 5 microns. In addition, the 10˝ as well as a 20˝ version are available in bulk packaging. NP24S NP48S 20˝ Bulk 4610-30 4610-26 4621-43 The NP246R Micromet Cartridge contains 1 pound of 6R Micromet, and it fits the NP24DD Housing. The NP486R Cartridge contains 2 pounds of 6R and fits the NP48DD Housing, with 10 micron filtration. NP246R NP486R Micro-Plus® & Micro-Carbon 4 The complete all-in-one treatment for ice machines, coffee urns and brewers, humidifiers, steamers, etc. The Micro-Plus “in-line” filters contain 6R Micromet® to control scale, high-grade activated carbon for eliminating objectionable tastes and odors, and filter discs to remove silt and sediment down to 20 microns. Available in four sizes with 1/4˝ FPT connections. When properly sized, each filter will last up to 6 months. The Micro-Carbon 4 is available for removing objectionable tastes and odors. Micro-Plus 2 Micro-Plus 4 Micro-Plus 8 Micro-Plus 16 Micro-Carbon 4 Water (per day) Ice (per day) Coffee (per week) 28 Micro-Plus 8 4702-87 4712-87 4621-43 6R Micromet® Cartridge Water Filtration Micro-Plus 4 4701-87 4711-87 Sediment Cartridge The CTL Series contains a matching product for the Tri-Liminator Filtration System with specifications that are nearly identical. For example, the CTL’s primary cartridge (C0070) will replace both the K00070 and K00174 cartridges, and it has more scale control ability than either of the Tri-Liminator cartridges. Part numbers are easily crossed over: CTL10 replaces the Tri-L10. Micro-Plus 2 4706-87 4716-87 Carbon Block Cartridge 4623-01 4623-02 4623-03 4623-06 The CTL Series Application 4704-24 4714-24 6R Micromet®/Sediment Cartridge Another custom cartridge within the NP Series, consisting of polypropylene for filtration (5 microns) and phosphate for scale-control. NP48PS 4717-87 NP Series Brackets 4615-W3 4612-W3 4613-Y8 4614-Y8 4617-24 Micro-Plus 16 4705-87 4715-87 Some installations may require two or three NP Series housings to meet more than one specific water-related condition. This custom installation can be accomplished through the use of one of the NP Series multi-housing brackets. Two housing brackets Three housing brackets NP2BR NP3BR Problem to Solve Micro-Carbon 4 12.5 gallons 25 gallons 50 gallons 100 gallons 50 gallons Cartridge Type Sediment Up to 125 lbs. Up to 250 lbs. Up to 500 lbs. Up to 1000 lbs. --- “S” Cartridges 4 25 lbs.(1,250 cups) 50 lbs. (2,500 cups) 100 lbs. (5,000 cups) 200 lbs. (10,000 cups) --- “C” Cartridges 4 “6R” Cartridges 4 “PC” Cartridges 4 “PS” Cartridges 4 Daily Capacities Taste & Odor Scale “48’s” 1800 lbs. (200 gal.) 3600 lbs. (400 gal.) 1800 lbs. (200 gal.) 3600 lbs. (400 gal.) 4 900 lbs. (100 gal.) 1800 lbs. (200 gal.) 4 600 lbs. (65 gal.) 1200 lbs. (135 gal.) 4 4 “24’s” 4 Visit us at www.nucalgon.com or call 1-800-554-5499 550 lbs. (60 gal.) 29 Water Filtration - NP Series Water Filtration - OEM Replacements Water Filtration - Nu-Plus® E Series by Everpure® MRS-20 Reverse Osmosis System Complete Mineral Reduction Water Processing System that removes at least 90%+ of all dissolved solids that cause scale build-up. The MRS-20 system removes taste and odor causing contaminants as well as dirt and particles. The two-part design makes installation flexible. It has no moving parts and requires no electrical power. System includes mineral reduction processor, carbon filter cartridge, reverse osmosis cartridge, and storage tank. No monitoring of grains per gallon is necessary. MRS-20 9797-91 Kleensteam CT and Kleensteam II Everpure’s second generation water treatment system for steam applications. Kleensteam is a total system delivering high quality filtered water with scale inhibition as well as deliming capabilities. The dual cartridge design provides enhanced performance for low and high flow capacity steamers and flexibility for expanding to meet future needs. Kleensteam also reduces chlorine-induced corrosion. It’s simple to install, operate, and maintain. Kleensteam CT Kleensteam II 1.67 gpm max. flow 2.5 gpm max. flow 9797-50 9797-21 Heads QL3B Single System Head Used with any Nu-Plus® E Series filters. Head includes a water shut-off valve with mounting bracket and screws. (3/8˝ NPT) 1 each 4621-07 QC7I Single Head Ideal for all Nu-Plus® E Series filters. Head includes a shut off, flushing valve, and outlet pressure gauge on a box bracket design. (3/8˝ NPT) 1 each Nu-Plus E Series by Everpure High Flow CSR Manifold with Prefilter Utilizing the nu-MC2 or the nu-XC2 cartridges, this system provides premium quality water to high flow fountain dispensers, coffee makers and ice machines. New and improved MicroPure II media inhibits the growth of bacteria. High Flow CSR reduces chlorine taste and odor and other offensive contaminants that can adversely effect the taste of beverages. Precoat submicron technology reduces dirt and particles as small as 1/2 micron and reduces health contaminants such as cysts. Additionally, the SRX Housing inhibits scale when it is equipped with scale-inhibiting IMF-7 and IMF-10 ScaleSticks®. 4621-01 QC7I Twin Parallel Head Dual filter head that is parallel plumbed for two Nu-Plus® E Series filters, either mix or match. Head includes a shut off, flushing valve, and outlet pressure gauge on a box bracket design. (3/4˝ NPT) 1 each 10˝ 20˝ Quad 9294-04 9294-24 4621-02 Nu-Plus E Series by Everpure Coldrink/Insurice Systems QC7I Triple Parallel Head Triple filter head parallel plumbed for three Nu-Plus® E Series filters. Head includes a shut off, flushing valve, and outlet pressure gauge on a box bracket design. (3/4˝ NPT) 1 each 4621-03 The Insurice Systems reduce ice machine problems caused by limescale formation, dirt, and particulate as well as objectionable tastes and odors caused by chlorine and other contaminants. Utilizing the Nu-Plus i20002 or i40002 cartridges as well as prefilters, the filtration systems keep ice machines running at peak efficiency. System is available with either a 10˝ or 20˝ prefilter, in single, twin, triple, and quad configurations. The cartridges’ MicroPure II technology insures a clean cartridge and filters out particles as small as 1/2 microns. QC7I Quad Parallel Head Quad filter head parallel plumbed for four Nu-Plus® E Series filters. Head includes a shut off, flushing valve, and outlet pressure gauge on a box bracket design. (3/4˝ NPT) 1 each High Flow CSR Manifold with Prefilter Twin Triple 9294-02 9294-03 9294-22 9294-23 4621-04 10˝ 20˝ Coldrink/Insurice Manifold with Prefilter Single Twin Triple 9293-01 9293-02 9293-03 9293-21 9293-22 9293-23 Quad 9293-04 9293-24 *Everpure® is a trademark of Everpure, Inc., Westmont, IL. 30 Visit us at www.nucalgon.com or call 1-800-554-5499 31 Water Filtration - Nu-Plus® E Series by Everpure® Systems Water Filtration - Nu-Plus® E Series by Everpure® Cartridges nu-i20002 and nu-i40002 7CB5 and nu-7CB5-S Reduces water-related ice machine problems caused by dirt, objectionable tastes and odor and scale build-up. Pre-coat submicron filtration reduces particles as small as 1/2 micron along with chlorine and other offensive contaminants. In addition, both cartridges use 6R Micromet®, a highly acclaimed scale inhibitor that inhibits scale build-up caused by dissolved minerals. NSF registered under NSF/ANSI Standards 42 and 53. The carbon block filter finely polishes the water by removing contaminates, allowing for high quality beverages and food applications. NSF registered under NSF/ANSI Standard 42. • Taste and odor, chlorine reduction • Scale control (nu-7CB5-S only) • Particulate reduction to 5 micron • Problem-solving cartridge for high particulate or low flow water pressure areas • • • • Pre-coat filtration with Micro-Pure® II antibacterial protection Premier 6R Micromet scale control Cyst and asbestos fibers reduction Sanitary quick-change cartridge replacement nu-i20002 4621-10 Capacity: 9,000 gallons • 750 lbs. for most cubers • 1,500 lbs. for most flakers 7CB5 Capacity: 10,000 gallons 9618-16 nu-7CB5-S Capacity: 10,000 gallons 4621-30 nu-i40002 4621-11 Capacity: 12,000 gallons • 1,000 lbs. for most cubers • 2,000 lbs. for most flakers nu-MC2 and nu-XC2 4CB5 and 4CB5-S Cartridge Reduces chlorine taste, odor and other offensive contaminants that can adversely affect the taste of fountain beverages. Pre-coat submicron filtration reduces particles as small as 1/2 micron, and it helps retain carbonation in drinks. NSF registered under NSF/ANSI Standards 42 and 53. Carbon Block filter finely polishes water for high quality beverages and food applications. NSF registered under NSF Standard 42. • Taste and odor, chlorine reduction • Scale control (4CB5-S only) • Particulate reduction to 5 micron • • • • Pre-coat filtration with Micro-Pure® II antibacterial protection Reduces objectionable tastes and odors Cyst and asbestos fibers reduction Sanitary quick-change cartridge replacement nu-MC2 Capacity: 9,000 gallons 4621-20 nu-XC2 Capacity: 12,000 gallons 4621-21 4CB5 Capacity: 6,000 gallons 4621-32 4CB5-S Capacity: 6,000 gallons 4621-31 BH2 and OCS2 Cartridge 7SO Softening Cartridge • • • • • • A softening cartridge that reduces scale-forming minerals like calcium and magnesium in hard water situations. It may be used on water having up to 30 grains hardness per gallon, at flow rates of up to 1/2 gallons per minute. It is a sanitary quick change cartridge that makes replacement easy. It should be used with an Everpure fine filter cartridge installed in a series plumbed twin head. Delivers premium quality water for ice and coffee applications Designed for applications where the i20002 is too long Precoat submicron particulate reduction Inhibits scale formation Taste & odor reduction NSF registered under NSF/ANSI Standard 42 and 53. BH2 4621-12 Capacity: 3,000 gallons or 6,000 pots of coffee 7SO Capacity: 2,000 grains • 0.5 gpm max. flow OCS2 9618-07 Capacity: 1,500 gallons or 3,000 pots of coffee • • • • Ideal for office or residential water systems Unique filter blend uses activated carbon to reduce chlorine taste, odor, and other offensive contaminants Reduces lead to below the Federal Action Level of 10 ppb Precoat submicron technology reduces dirt and particles as small as 1/2 micron Inhibits scale build-up in water-using appliances NSF registered under NSF/ANSI Standards 42 and 53 OW200L Capacity: 480 gallons 9619-06 OW4PLUS Capacity: 2,000 gallons 9635-06 *Everpure® is a trademark of Everpure, Inc., Westmont, IL. 32 Replacement Cartridges for CUNO® Nu-Plus® CU and Nu-Plus CU-S OW200L and OW4Plus Cartridge • • 9607-04 The Nu-Plus E Series CU and CU-S cartridges are replacements that are compatible with the CUNO Series CFS 8000 filter cartridges. Both incorporate a carbon block filter that reduces objectionable tastes and odors as well as chlorine and other contaminates, providing high quality beverage and ice. They also reduce extra fine dirt as small as 5 microns. Additionally, the CU-S provides for the reduction of scale formation. Nu-Plus CU 4622-20 Capacity: 10,000 gallons (37,850 liters) • 1.5 gpm flow Replaces CFS-8112, CFS-8720 & CFS-8812 Nu-Plus CU-S 4622-10 Capacity: 10,000 gallons (37,850 liters) • 1.5 gpm flow Replaces CFS-8112S,CFS-8720S & CFS-8812S *CUNO® is a trademark of 3M. This product is not manufactured, sponsored, or affiliated with 3M. Visit us at www.nucalgon.com or call 1-800-554-5499 33 Water Filtration - Nu-Plus® E Series by Everpure® Cartridges Water Filtration - Nu-Plus® E Series by Everpure® 7SI Cartridge Nu-Plus® 10˝ and 20˝ Coarse Prefilters A 10˝ and 20˝ clear housing, each including a 10˝ and 20˝ replaceable prefilter cartridge. Filters out larger dirt and rust particles thereby extending the life of submicron and carbon block filters. E-10 E-20 New Filtration Technology Specially designed for ice machines. This cartridge does not include carbon. The cartridge reduces sediment and particulate down to 1/2 micron and reduces cyst and Giardia. The filter allows chlorine to pass through which helps reduce slime and bacteria growth inside the ice machine and ice bin. Ideal for food service operations where baking of bread and pastries is done on-site. • Scale inhibition • Particulate reduction • Cyst reduction • 3.5 gpm flow rate • 0.5 micron rating • NSF Std 42 and 53 NEW 4621-42 4621-44 Optional: Wing Bracket for all multiple filter head systems manufactured after 2003: 4621-45 Nu-Plus® EC110 and EC210 7SI Capacity: 25,000 gallons A 10˝ and 20˝, 10 micron nominal filtration cartridge for filtering out larger dirt and rust particles, extending the life of primary filters. For use in the E-10 and E-20 housings as well as other 10˝ and 20˝ housings. EC110 (10˝) EC210 (20˝) 4621-41 4621-43 7FC Cartridge NEW New Fiberdyne™ II media with Agion® antimicrobial protection to inhibit potential bacterial growth. Balanced for optimum performance in varying water qualities. Improves the taste of fountain drinks and helps retain the drink’s carbonation. • Taste & odor reduction • Particulate Reduction • 2.5 gpm flow rate • 0.5 Micron Rating • NSF Standards 42 and 53 SRX Scale Inhibitor Feeder A complete system for the control of scale in ice, coffee, steam, and combination applications. It dispenses a controlled amount of HydroBlend™ compound which provides for a more consistent feed and longer life. The system includes a clear housing, one cartridge, and a spacer. 1 each 9606-01 4621-05 7FC Capacity: 25,000 gallons Optional: Wing Bracket for all multiple filter head systems manufactured after 2003: 4621-06 9692-61 Nu-Plus® IMF-7 and IMF-10 Ice Machine Feeder Scale inhibition cartridge. The translucent cartridge allows for easy visual monitoring of the product’s usage. The larger IMF-10 will last longer or treat higher volumes of water. IMF-7 IMF-10 Replacement for AR-X 7˝ Housing Replacement for SS-10 Scale Sticks 7CLM Cartridge NEW Reduces chloramines, chlorine taste and odor and other offensive contaminants that can adversely affect the taste of beverages. The cartridge reduces particles down to 1/2 micron and reduces cysts and Giardia. Improves the taste of fountain beverage and helps retain the drink’s carbonation. NSF registered. • Chloramine reduction • Chlorine reduction • Cyst reduction • Particulate reduction 4621-13 4621-14 4JT Flushing/Sanitizing Cartridge The preferred way to introduce ScaleKleen™ Scale Remover or other sanitizing solutions (IMS-II) into all water-using equipment and vending machines. Fits into existing Everpure heads. Eliminates the need for difficult component disassembly. Easy and convenient to help you clean and maintain equipment. Approved by NAMA. 1 each 7CLM 9693-01 Capacity: 3,600 gallons at 1.7 gpm, 5,500 gallons at 1.33 gpm 4621-00 NEW Nu-Plus® E-Series by Everpure® Claris Water Technology Claris offers tailored hardness control for perfect hot beverages. Thanks to its compact dimensions and the sophisticated multi-valve connection head, the system can be installed and operated almost anywhere, free standing, mounted or in a vertical or horizontal position. ScaleKleen™ Scale Remover Restores equipment to peak operating efficiency by removing scale build-up. Quickly removes limescale from coffee brewers. Ideal for deliming steam and ware washing equipment. Great for office coffee system (OCS) applications. Non-toxic, safe to skin and won’t burn clothing. Sewer system disposable; can be poured down the drain. Use with 4JT Flushing/Sanitizing Cartridge. 7 ounce packets (24 per case) 2.2 lb. canister (4 per case) Claris S Claris M Claris L Claris XL 4621-17 9798-35 396 gallons of coffee 660 gallons of coffee 1,110 gallons of coffee 1,585 gallons of coffee 14.37˝ 18.70˝ 16.14˝ 20.67˝ 4339-10 4339-11 4339-12 4339-13 *Everpure® is a trademark of Everpure, Inc., Westmont, IL. 34 5 Visit us at www.nucalgon.com or call 1-800-554-5499 35 Water Filtration - Nu-Plus® E Series by Everpure® Other Filtration Products Nu-Calgon Seminars & Training Classes Serving the United States & Canada with the Finest Direct Factory Sales Force in the HVACR Industry Free Seminars and Training Classes Coil Cleaning: The Clean Coil Program is a comprehensive seminar dedicated to the safe and proper procedures to clean evaporator and condenser coils. The program will help determine which cleaning method should be utilized for a particular job based on the type and condition of the unit. NATE Recognition Classes: 1 hour Continuing Education Accreditation Ice Machine Treatment and Filtration: A complete guide to “Extending the Life of an Ice Machine.” The seminar will answer the questions: why use a filter, what filter should be used, and how to keep the system clean, clear, and running properly. It also addresses all of the water-related problems associated with ice machines. (1.5 hours) Indoor Air Quality Management: The seminar covers the past, present and future of indoor air quality (IAQ). Topics covered in the session: how poor IAQ impacts a business, common causes of poor IAQ, and how to prevent poor IAQ from occurring. NATE Recognition Classes: 1 hour Continuing Education Accreditation Nu-Calgon Product Line Review: The seminar provides an overview of all the major products that Nu-Calgon offers. The presentation explores when and where to use certain products, as well as explains how using certain products can save time and money. (2 hours) Refrigeration Oils: An in-depth look at industry refrigeration oils (Mineral, Alkylbenzene, and POE) and when and where to use them. NATE Recognition Classes: 1.5 hours Continuing Education Accreditation Total System Protection: A thorough look at why burnouts occur, how to prevent them and the proper way to flush a system once a burnout occurs. The training will include acid testing and acid neutralization. NATE Recognition Classes: 1 hour Continuing Education Accreditation Water Treatment: This seminar will cover the fundamentals of water treatment for cooling towers, evaporative condensers, boilers, and chillers. NATE Recognition Classes: 1.5 hours Continuing Education Accreditation Winter Water Treatment: This program focuses on what a system needs prior to the winter season, including a review of ethylene and propylene glycol, the proper treatments for hot/cold closed systems, and low make-up steam systems. (1 hour) Energy Savings with A/C Re-New: Learn about a revolutionary product for revitalizing and energizing a/c systems. The seminar will explain how A/C Re-New will help reduce energy costs, improve cooling performance and reduce the system noise. (1 hour) Food Service Products for Ice & Beverage Filtration: A comprehensive look on the problems associated with ice and beverage filtration as well as treatment options to solve these problems. We will cover products for ice makers, coffee brewers, fountain beverage machines, steam ovens, drinking water, and more. (1 hour) 1. Seattle, WA 11. Kansas City, MO 21. Ocala, FL 2. Northern CA 12. St. Paul - Minneapolis 22. Tampa, FL 3. Southern CA 13. St. Louis, MO 23. Miami, FL 4. Los Angeles, CA 14. Baton Rouge, LA 24. Raleigh, NC 5. San Diego, CA 15. Chicago, IL 25. Richmond, VA 6. Phoenix, AZ 16. Chicago, IL 26. Baltimore, MD 7. Denver, CO 17. Indianapolis, IN 27. Philadelphia, PA 8. San Antonio, TX 18. Columbus, OH 28. NYC/New Jersey 9. Dallas - Fort Worth 19. Birmingham, AL 29. Syracuse, NY 10. Houston, TX 20. Atlanta, GA 30. Boston, MA St. Louis, MO (Hdq.) 36 Visit us at www.nucalgon.com or call 1-800-554-5499 37 Our Name on the Outside Means Quality on the Inside Nu-Calgon 2008 Altom Court | St. Louis, MO 63146 phone: 800-554-5499 | fax: 800-221-6302 www.nucalgon.com (612) 3-300 Calgon is a licensed trade name.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Tagged PDF : Yes Page Count : 21EXIF Metadata provided by EXIF.tools