Manual For The 63297 10 Ft. X Portable Shed
User Manual: Manual for the 63297 10 ft. x 10 ft. Portable Shed 10 ft. x 10 ft. Portable Shed
Open the PDF directly: View PDF 
.
Page Count: 12
Visit our website at: http://www.harborfreight.com
Email our technical support at: predator@harborfreight.com
WARNING! Do not start or operate any internal
combustion engine inside or near Shed.
Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright© 2016 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly an d se rv ic e may n ot b e in cl uded.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
REV 17a
Page 2 For technical questions, please call 1-888-866-5797. Item 63297
Table of Contents
Safety ......................................................... 3
Specifications ............................................. 4
Assembly .................................................... 4
Maintenance .............................................. 10
Parts List.................................................... 11
Warranty .................................................... 12
WARNING SYMBOLS AND DEFINITIONS
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.
Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
Addresses practices not related to personal injury.
WARNING marking concerning Risk
of Eye Injury. Wear ANSI-approved
safety goggles with side shields.
Read the manual before
assembly and/or use.
WARNING marking concerning
Risk of Head Injury. Wear hard hat
during assembly and service.
WARNING marking concerning Risk
of Hand Injury. Wear heavy-duty work
gloves during assembly and service.
WARNING marking concerning
Risk of Respiratory Injury.
Operate engine OUTSIDE and far
away from windows, doors, and vents.
SAFETY MAINTENANCE
ASSEMBLY
Page 3For technical questions, please call 1-888-866-5797.Item 63297
IMPORTANT SAFETY INFORMATION
Read all safety warnings and instructions.
Failure to follow the warnings and instructions may result in serious injury.
Save all warnings and instructions for future reference.
The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible
conditions and situations that may occur. It must be understood by the operator that common sense
and caution are factors which cannot be built into this product, but must be supplied by the operator.
Assembly Precautions
1. Do not assemble in windy conditions.
2. Assemble and install only on
flat, level, hard surface.
3. Assemble and anchor only according to
these instructions. Improper assembly or
inadequate anchoring can create hazards.
4. Check for utility lines, tree branches and
other structures before assembling.
5. Verify that installation surface has no
hidden utility lines before anchoring.
6. Wear ANSI-approved safety goggles,
heavy-duty work gloves and hard hat
during assembly and service.
7. Keep assembly area clean and well lit.
8. Keep bystanders out of the area during assembly.
9. Do not assemble when tired or when under
the influence of drugs or medication.
10. Product capabilities apply to properly and
completely assembled product only.
Use Precautions
1. CARBON MONOXIDE HAZARD
Using an engine inside Shed
CAN KILL YOU IN MINUTES.
Engine exhaust contains
carbon monoxide. This is a poison
you cannot see or smell.
NEVER use an engine inside Shed,
EVEN IF cover is open.
Only use an engine OUTSIDE and far away from
Shed.
2. DO NOT USE IN HIGH WIND. Remove cover
if harsh weather or heavy rain threatens.
3. For temporary use only.
Do not use for long-term shelter.
4. Do not use as tent. Does not meet tent
flammability standards. Do not use grill, heater,
or ignition sources inside or near cover.
5. Do not allow snow, rainwater or debris
to accumulate or pool on cover.
6. Do not hang objects from any part of the Shed.
7. This product is not a toy. Do not allow
children to play with or near this item.
8. Use as intended only.
9. Inspect regularly, tighten all loose hardware and
loose ropes, and secure all loosened anchors.
If any parts are damaged, bent, or stretched, they
must be replaced. Hardware may loosen during
normal operation stresses. Loose hardware
or damaged/altered parts will compromise
the structural integrity of this product.
10. Maintain product labels and nameplates.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.
SAVE THESE INSTRUCTIONS.
SAFETYMAINTENANCE ASSEMBLY
Page 4 For technical questions, please call 1-888-866-5797. Item 63297
Specifications
Overall Dimensions 10′ W x 10′ L
Center Height 7′ 10″
Side Height 6′ 3″
Pole Diameter 1-3/8″
Assembly Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this
manual including all text under subheadings therein before set up or use of this product.
TO PREVENT SERIOUS INJURY:
Do not leave this product partially assembled. Assemble this product completely at one time.
Note: At least 3 workers are required for assembly. Before starting assembly, review the instructions and make sure
there is enough time and the proper tools available to properly assemble.
Finger tighten all connections until assembly is done. Assemble on a flat, level surface.
Assemble Roof
Note: Unless where otherwise noted, this product’s assembly is done using
slip fit construction. Make sure all parts seat completely and securely. A rubber
mallet (sold separately) can be used to gently tap parts in place to ensure a tight fit.
1. Lay out Roof parts.
4
7
5
5
5
5
5
5
7
4
10 10
4
48
8
4
11
4
9
9
SAFETY MAINTENANCE
ASSEMBLY
Page 5For technical questions, please call 1-888-866-5797.Item 63297
NOTICE: To prevent damage to material, make sure all hardware is installed
with Bolts facing cover and Nuts facing inside, away from cover.
2. Connect Top Rails (4) to 4-Way Center
Connector (11), then connect 3-Way Rail
Connectors (10) to the free end of each rail.
3. Connect two Rafters (5) to each Connector, secure
Rafters with longer Bolts M6x50 (15) and Nuts (16).
5
5
5
55
5
4
10
15
10 11
4
16
15
16
16
15
4. Connect together:
a. 3-Way Corner Connector B (8)
b. Top Rail (4)
c. 4-Way Center Connector (9)
d. Top Rail (4)
e. 3-Way Corner Connector A (7).
5. Attach assembly to the three Top Rails (5) on one side.
6. Repeat on other side.
4
4
7
8
9
5
5
5
Assemble and Attach Legs
1. Assemble four Corner Legs by attaching
four Corner Feet (3) to four Legs (1).
Corner
Foot (3)
Leg (1)
2. Assemble two Center Legs by attaching
two Center Feet (2) to two Legs (1).
Leg (1)
Center
Foot (2)
SAFETYMAINTENANCE ASSEMBLY
Page 6 For technical questions, please call 1-888-866-5797. Item 63297
3. Attach Corner Legs to 3-Way Corner Connectors. Attach Center Legs to 4-Way Center Connectors.
Corner
Leg Center
Leg
3-Way
Corner
Connector
4-Way
Center
Connector
4. Connect four Bottom Rails (6) between Center and Corner Legs:
a. For Center Legs: Place one Center Clamp (12)
on the front and one on the back of the
connection. Secure with two sets of shorter
Bolts M6x40 (17), Washers (18) and Nuts (16).
b. For Corner Legs: Place one Corner Clamp (13)
on the front and one on the back of the
connection. Secure with one set of shorter Bolts
M6x40 (17), Washers (18) and Nuts (16).
Corner
Clamp (13)
Center
Clamp (12)
Bottom
Rail (6) Bottom
Rail (6)
Nut
(16)
Nut
(16)
Corner
Leg
Washer
(18)
Washer
(18)
Center
Leg
Bolt
(17)
Bolt
(17)
SAFETY MAINTENANCE
ASSEMBLY
Page 7For technical questions, please call 1-888-866-5797.Item 63297
Square up the Frame
TO PREVENT SERIOUS INJURY: Contact local utility companies to ensure that the installation area is
free of pipes, cables, and other hazards BEFORE choosing installation area or installing anchors.
1. Position the frame in the desired location,
making sure it is level and flat.
2. Measure between diagonal corners. These
measurements must be within 1″ of each other.
3. Measure across front and back. These
measurements must be 10' each.
4. If any measurements do not match, adjust the frame
and measure again until measurements match.
Anchor the Frame
WARNING! Anchor only according to these instructions. Improper assembly
or inadequate anchoring can create hazards.
CAUTION! To prevent tripping hazard, position Anchors toward
the interior of the frame, close to the Corner Feet.
1. Use a metal bar (sold separately) to thread the
Anchor (14) into the ground, until the loop at the
top of the Anchor extends just above the ground.
Note: When anchoring to concrete, use
Concrete Anchors (not included).
2. Insert a Wire Rope (23) through the
Anchor and Corner Foot.
3. Tighten the Wire Rope and secure it
using a Wire Rope Clamp (24). Tighten
the nuts on the Clamp evenly.
Wire Rope
(23) Interior
of Frame
Wire Rope
Clamp (24)
4. Repeat on the other corners.
Note: Center Feet may be anchored to increase stability.
SAFETYMAINTENANCE ASSEMBLY
Page 8 For technical questions, please call 1-888-866-5797. Item 63297
Attach Front and Back Covers
1. Position Front Cover (20) so that zipper
pulls are facing toward the outside.
Make sure zippers are closed.
2. From inside, remove Center Top Rail, then line up
top opening on cover with 3-Way Connector. Wrap
Cover over tubes so that Strap is under Connector.
3. Replace Center Top Rail.
4. Repeat with other two Top Rails.
5
Center
Top Rail
Top
Rail
Top
Rail
Inside
Straps
5. Thread Strap through Ratchet Tie Down’s (22)
spindle. Repeat on other side.
Strap
Spindle
Ratchet Tie
Down (22)
6. Hook Ratchet Tie Downs into Corner Feet. Raise
and lower the handles to tighten straps, alternating
between left and right Feet, until straps are snug.
7. Repeat for Back Cover (21).
SAFETY MAINTENANCE
ASSEMBLY
Page 9For technical questions, please call 1-888-866-5797.Item 63297
Attach Roof
1. Stretch Top Cover (19) over the frame,
making sure it is centered.
2. Thread Straps through Ratchet Tie Down’s spindles.
3. Hook Ratchet Tie Downs into Corner Feet.
Raise and lower the handles to tighten straps
slightly, leaving slack in the Top Cover.
4. Unzip and roll up Front Cover, securing
Cover with hook and eye straps.
5. From the inside, on one side of the Shed,
remove Clamps from Bottom Rails.
6. Remove Bottom Rails, insert Bottom Rails into
pockets, then reattach Clamps to Bottom Rails.
7. Repeat on other side of Shed.
8. Raise and lower the Ratchet Tie Down’s
handles, alternating between each
corner, until straps are snug.
Pocket
Bottom
Rails
Ratchet
Tie Down
Pocket
Strap
9. Tighten all connections throughout the shed
before use.
Do not overtighten.
SAFETYMAINTENANCE ASSEMBLY
Page 10 For technical questions, please call 1-888-866-5797. Item 63297
Maintenance
Procedures not specifically explained in this manual must
be performed only by a qualified technician.
TO PREVENT SERIOUS INJURY FROM PRODUCT FAILURE:
Do not use damaged products. If damage is noted, have the problem corrected before further use.
Inspection
MONTHLY, inspect the general condition of the Portable Shed. Check for:
• loose ratchet tie downs, anchors, tube connections, and rail clamps (tighten as needed),
• torn or frayed covers, ropes, or wire ropes,
• cracked, bent, or broken parts, and
• any other condition that may affect its safe operation.
Cleaning
1. Immediately remove any accumulated
debris from the cover with a broom, mop,
or other soft-sided instrument from the
outside. DO NOT use sharp instruments.
2. PERIODICALLY, clean cover with mild
soap and water. DO NOT use bleach
or harsh abrasive products.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST IN THIS MANUAL
AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY
REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO
MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS
OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES
THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Record Product’s Serial Number Here:
Note: If product has no serial number, record
month and year of purchase instead.
Note: Some parts are listed and shown for
illustration purposes only, and are not available
individually as replacement parts.
SAFETY MAINTENANCE
ASSEMBLY
Page 11For technical questions, please call 1-888-866-5797.Item 63297
Parts List
Note: Individual part illustrations not to scale.
Part Description Illustration Qty
1 Leg 6
2 Center Foot 2
3 Corner Foot 4
4 Top Rail 6
5 Rafter 6
6 Bottom Rail 4
73-Way Corner
Connector A 2
83-Way Corner
Connector B 2
94-Way Center
Connector 2
10 3-Way Rail
Connector 2
11 4-Way Center
Connector 1
12 Center Clamp 4
Part Description Illustration Qty
13 Corner Clamp 8
14 Anchor 4
15 Bolt M6x50 6
16 Nut M6 14
17 Bolt M6x40 8
18 Washer M6 8
19 Top Cover 1
20 Front Cover
with Zipper 1
21 Back Cover 1
22 Ratchet Tie Down 8
23 Wire Rope 4
24 Wire Rope Clamp 4
SAFETYMAINTENANCE ASSEMBLY
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
