Hotwire ReachDSL Modem, 6350 A4, Installation Instructions A2 GN12 10 GX40 00

6350-A2-GX40-00 6350-A2-GX40-00

User Manual: 6350-A2-GX40-00

Open the PDF directly: View PDF .
Page Count: 8

1

6350 Important Instruction Notification

Document Number 6350-A2-GX40-00

June 2004

Software and Firmware License Agreement

The terms and conditions of this License Agreement (the “Agreement”) will apply to the

software and/or firmware (individually or collectively the “Software”) incorporated into

the Paradyne product (the “Product”) purchased by you and any derivatives obtained

from the Software, including any copy of either. If you have executed a separate written

agreement covering the Software supplied to you under this purchase, such separate

written agreement shall govern.

Paradyne Corporation (“Paradyne”) grants to you, and you (“Licensee”) agree to accept

a personal, non-transferable, non-exclusive, right (without the right to sublicense) to use

the Software, solely as it is intended and solely as incorporated in the Product

purchased from Paradyne or its authorized distributor or reseller under the following

terms and conditions:

1. Ownership: The Software is the sole property of Paradyne and/or its licensors. The

Licensee acquires no title, right or interest in the Software other than the license

granted under this Agreement.

2. Licensee shall not use the Software in any country other than the country in which

the Product was rightfully purchased except upon prior written notice to Paradyne

and an agreement in writing to additional terms.

3. The Licensee shall not reverse engineer, decompile or disassemble the Software in

whole or in part.

4. The Licensee shall not copy the Software except for a single archival copy.

ONCE YOU HAVE READ THIS LICENSE AGREEMENT AND AGREE TO ITS

TERMS, YOU MAY USE THE SOFTWARE AND/OR FIRMWARE INCORPORATED

INTO THE PARADYNE PRODUCT. BY USING THE PARADYNE PRODUCT YOU

SHOW YOUR ACCEPTANCE OF THE TERMS OF THIS LICENSE AGREEMENT.

IN THE EVENT THAT YOU DO NOT AGREE WITH ANY OF THE TERMS OF THIS

LICENSE AGREEMENT, PROMPTLY RETURN THE UNUSED PRODUCT IN ITS

ORIGINAL PACKAGING AND YOUR SALES RECEIPT OR INVOICE TO THE

LOCATION WHERE YOU OBTAINED THE PARADYNE PRODUCT OR THE

LOCATION FROM WHICH IT WAS SHIPPED TO YOU, AS APPLICABLE, AND YOU

WILL RECEIVE A REFUND OR CREDIT FOR THE PARADYNE PRODUCT

PURCHASED BY YOU.

2

5. Except for the Product warranty contained in the manual, the Software is provided

“AS IS” and in its present state and condition and Paradyne makes no other

warranty whatsoever with respect to the Product purchased by you. THIS

AGREEMENT EXPRESSLY EXCLUDES ALL OTHER WARRANTIES, WHETHER

EXPRESS OR IMPLIED, OR ORAL OR WRITTEN, INCLUDING WITHOUT

LIMITATION:

a. Any warranty that the Software is error-free, will operate uninterrupted in your

operating environment, or is compatible with any equipment or software

configurations; and

b. ANY AND ALL IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION

IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A

PARTICULAR PURPOSE AND NON-INFRINGEMENT.

Some states or other jurisdictions do not allow the exclusion of implied warranties

on limitations on how long an implied warranty lasts, so the above limitations may

not apply to you. This warranty gives you specific legal rights, and you may also

have other rights which vary from one state or jurisdiction to another.

6. IN NO EVENT WILL PARADYNE BE LIABLE TO LICENSEE FOR ANY

CONSEQUENTIAL, INCIDENTAL, PUNITIVE OR SPECIAL DAMAGES,

INCLUDING ANY LOST PROFITS OR LOST SAVINGS, LOSS OF BUSINESS

INFORMATION OR BUSINESS INTERRUPTION OR OTHER PECUNIARY LOSS

ARISING OUT OF THE USE OR INABILITY TO USE THE SOFTWARE,

WHETHER BASED ON CONTRACT, TORT, WARRANTY OR OTHER LEGAL OR

EQUITABLE GROUNDS, EVEN IF PARADYNE HAS BEEN ADVISED OF THE

POSSIBILITY OF SUCH DAMAGES, OR FOR ANY CLAIM BY ANY THIRD

PARTY.

7. The rights granted under this Agreement may not be assigned, sublicensed or

otherwise transferred by the Licensee to any third party without the prior written

consent of Paradyne.

8. This Agreement and the license granted under this Agreement shall be terminated

in the event of breach by the Licensee of any provisions of this Agreement.

9. Upon such termination, the Licensee shall refrain from any further use of the

Software and destroy the original and all copies of the Software in the possession

of Licensee together with all documentation and related materials.

10. This Agreement shall be governed by the laws of the State of Florida, without

regard to its provisions concerning conflicts of laws.

3

Important Safety Instructions

1. Read and follow all warning notices and instructions marked on the product or included in the manual.

2. Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product

and to protect it from overheating, these slots and openings must not be blocked or covered.

3. Do not allow anything to rest on the power cord and do not locate the product where persons will walk on

the power cord.

4. Do not attempt to service this product yourself, as opening or removing covers may expose you to

dangerous high voltage points or other risks. Refer all servicing to qualified service personnel.

5. General purpose cables are used with this product for connection to the network. Special cables, which

may be required by the regulatory inspection authority for the installation site, are the responsibility of the

customer. Use a UL Listed, CSA certified, minimum No. 24 AWG line cord for connection to the Digital

Subscriber Line (DSL) network.

6. When installed in the final configuration, the product must comply with the applicable Safety Standards and

regulatory requirements of the country in which it is installed. If necessary, consult with the appropriate

regulatory agencies and inspection authorities to ensure compliance.

7. A rare phenomenon can create a voltage potential between the earth grounds of two or more buildings. If

products installed in separate buildings are interconnected, the voltage potential may cause a hazardous

condition. Consult a qualified electrical consultant to determine whether or not this phenomenon exists and,

if necessary, implement corrective action prior to interconnecting the products.

8. Input power to this product must be provided by one of the following: (1) a UL Listed/CSA certified power

source with a Class 2 or Limited Power Source (LPS) output for use in North America, or (2) a certified

transformer, with a Safety Extra Low Voltage (SELV) output having a maximum of 240 VA available, for use

in the country of installation.

9. In addition, since the equipment is to be used with telecommunications circuits, take the following

precautions:

— Never install telephone wiring during a lightning storm.

— Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.

— Never touch uninsulated telephone wires or terminals unless the telephone line has been

disconnected at the network interface.

— Use caution when installing or modifying telephone lines.

— Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a

remote risk of electric shock from lightning.

— Do not use the telephone to report a gas leak in the vicinity of the leak.

CE Marking

When the product is marked with the CE mark on the equipment label, this demonstrates full compliance with the

following European Directives:

Directive 73/23/EEC – Council Directive of 19 February 1973 on the harmonization of the laws of the

member states relating to electrical equipment designed for use within states relating to electrical

equipment designed for use within certain voltage limits, as amended by Directive 93/68/EEC.

Directive 89/336/EEC – Council Directive of 3 May 1989 on the approximation of the laws of the member

states relating to Electro-Magnetic Compatibility (EMC), as amended by Directive 93/68/EEC.

CANADA – EMI NOTICE:

!

This Class B digital apparatus meets all requirements of the Canadian interference-causing

equipment regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du règlement sur le matérial

brouilleur du Canada.

!

4

Declaration of Conformity

This Declaration of Conformity is made by Paradyne Corporation pursuant to Parts 2 and 15 of the Federal

Communications Commission’s Rules. This compliance information statement pertains to the following products:

Trade Name: Hotwire

Model Number: 6350-A4-200

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this

device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

The name, address, and telephone number of the responsible party is given below:

Paradyne Corporation

8545 126th Avenue North

Largo, FL 33773-1502

Phone: (727) 530-2000

The authority to operate this equipment is conditioned by the requirement that no modifications will be made to

the equipment unless the changes or modifications are expressly approved by Paradyne Corporation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help

Supplier’s Declaration of Conformity

Place of Issue: Paradyne Corporation

8545 126th Avenue North

Largo, FL 33773-1502

USA

Date of Issue: 8/17/2001

Paradyne Corporation, located at the above address, hereby certifies that the Hotwire® ReachDSL™ Model

Number 6350-A4-200, bearing labeling identification number US:AW2DL03B6350-A4 complies with: the Federal

Communications Commission’s (“FCC”) Rules and Regulations 47 CFR Part 68, the Administrative Council on

Terminal Attachments (“ACTA”)-adopted technical criteria TIA/EIA/IS-968, “Telecommunications – Telephone

Terminal Equipment – Technical Requirements for Connection of Terminal Equipment To the Telephone Network,

July 2001,” and TIA/EIA/IS-883, “Telecommunications – Telephone Terminal Equipment – Supplemental

Technical Requirements for Connection of Stutter Dial Tone Detection Devices and ADSL Modems to the

Telephone Network, June 2001.”

John Koehler

Senior Vice President, DSL Products and Worldwide Services

5

Government Requirements

Certain governments require that instructions pertaining to connection to the telephone network be included in the

installation and operation manual. Specific instructions are listed in the following sections.

United States – Notice to Users of the Telephone Network

1. This equipment complies with Part 68 of the FCC rules. On the equipment is a label that contains, among

other information, the FCC approval number which includes the Ringer Equivalence Number (REN) for this

equipment. The label is located on the bottom of your modem.

2. The Hotwire 6350 ReachDSL Modem connects to the Public Switched Telephone Network (PSTN) using

the Universal Service Order Code (USOC) RJ11C or RJ14C.

3. The REN is used to determine the quantity of devices which may be connected to the telephone line.

Excessive RENs on the telephone line may result in the devices not ringing in response to an incoming call.

In most, but not all areas, the sum of the RENs should not exceed five (5.0). To be certain of the number of

devices that may be connected to the line, as determined by the total RENs, contact the telephone

company to determine the maximum RENs for the calling area.

4. If the modem causes harm to the telephone network, the telephone company will notify you in advance that

temporary discontinuance of service may be required. But if advance notice is not practical, the telephone

company will notify the customer as soon as possible. Also, you will be advised of your right to file a

complaint with the FCC if you believe it is necessary.

5. The telephone company may make changes in its facilities, equipment, operations, or procedures that

could affect the operation of the equipment. If this happens, the telephone company will provide advance

notice in order for you to make the necessary modifications in order to maintain uninterrupted service.

6. If you experience trouble with this equipment, please contact your sales or service representative (as

appropriate) for repair or warranty information. If the product needs to be returned to the company service

center for repair, contact them directly for return instructions using one of the following methods:

—Internet: Visit the Paradyne World Wide Web site at www.paradyne.com.

—Telephone: Call our automated system to receive current information via fax or to speak with a

company representative.

Within the U.S.A., call 1-800-870-2221

Outside the U.S.A., call 1-727-530-2340

If the trouble is causing harm to the telephone network, the telephone company may request that you

remove the equipment from the network until the problem is resolved.

7. The user is not authorized to repair or modify the equipment.

8. This equipment cannot be used on public coin service provided by the telephone company. Connection to

Party Line Service is subject to state tariffs. (Contact the state public utility commission, public service

commission or corporation commission for information.)

9. An FCC compliant telephone cord with modular plugs may be provided with this equipment. This equipment

is designed to be connected to the telephone network or premises wiring using a compatible modular jack

which is Part 68 compliant.

6

Notice to Users of the Canadian Telephone Network

The Industry Canada label identifies certified equipment. This certification means that the equipment meets

telecommunications network protective, operational and safety requirements as prescribed in the appropriate

Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment

will operate to the user’s satisfaction.

Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the

local telecommunications company. The equipment must also be installed using an acceptable method of

connection. The customer should be aware that compliance with the above conditions may not prevent

degradation of service in some situations.

Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs

or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications

company cause to request to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of the power utility, telephone

lines and internal metallic water pipe system, if present, are connected together. This precaution may be

particularly important in rural areas.

CAUTION:

Users should not attempt to make such connections themselves, but should contact the

appropriate electric inspection authority, or electrician, as appropriate.

The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum

number of terminals allowed to be connected to a telephone interface. The termination on an interface may

consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence

Numbers of all the devices does not exceed 5.

If your equipment is in need of repair, refer to Warranty, Sales, Service, and Training Information.

Warranty, Sales, Service, and Training Information

Contact your local sales representative, service representative, or distributor directly for any help needed. For

additional information concerning warranty, sales, service, repair, installation, documentation, training, distributor

locations, or Paradyne worldwide office locations, use one of the following methods:

Internet: Visit the Paradyne World Wide Web site at www.paradyne.com. (Be sure to register your

warranty at www.paradyne.com/warranty.)

Telephone: Call our automated system to receive current information by fax or to speak with a company

representative.

— Within the U.S.A., call 1-800-870-2221

— Outside the U.S.A., call 1-727-530-2340

Trademarks

Hotwire and MVL are registered trademarks of Paradyne Corporation. ReachDSL is a trademark of Paradyne

Corporation. All other products and services mentioned herein are the trademarks, service marks, registered

trademarks, or registered service marks of their respective owners.

7

8

,

*6350-A2-GX40-00*

Copyright © 2004 Paradyne Corporation. Printed in U.S.A.