Manual For The 69465 Infrared Thermometer With Laser Targeting, Non Contact
User Manual: Manual for the 69465 Infrared Thermometer with Laser Targeting, Non-Contact Non-Contact Infrared Thermometer With Laser Targeting
Open the PDF directly: View PDF 
.
Page Count: 8
| Download | |
| Open PDF In Browser | View PDF |
Owner’s Manual & Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference. 17k Visit our website at: http://www.harborfreight.com Email our technical support at: productsupport@harborfreight.com When unpacking, make sure that the product is intact and undamaged. If any parts are missing or broken, please call 1-888-866-5797 as soon as possible. Copyright© 2012 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included. Read this material before using this product. Failure to do so can result in serious injury. SAVE THIS MANUAL. WARNING SYMBOLS AND DEFINITIONS This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. SAFETY Indicates a hazardous situation which, if not avoided, will result in death or serious injury. Indicates a hazardous situation which, if not avoided, could result in death or serious injury. Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. Addresses practices not related to personal injury. SETUP IMPORTANT SAFETY INFORMATION Read all safety warnings and instructions. Failure to follow the warnings and instructions may result in serious injury. 1. Do not use for medical purposes. 2. Do not open the housing other than battery compartment. 3. Avoid direct Eye exposure. OPERATION 4. Do not expose the tool to rain or wet conditions. 5. Stay alert, watch what you are doing and use common sense when operating the tool. Do not use while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention may result in serious personal injury. MAINTENANCE 6. Do not use the tool if the Trigger does not turn it on and off. Any tool that cannot be controlled with the Trigger is dangerous and must be repaired. 7. Disconnect the battery before making any adjustments, changing accessories, or storing the tool. Such preventive safety measures reduce the risk of activating the Laser accidentally. Page 2 8. Maintain the tool. Check for misalignment or binding of parts, breakage of parts and any other condition that may affect the tool’s operation. If damaged, have the tool repaired before use. Many accidents are caused by poorly maintained tools. 9. Use the tool in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the tool for operations different from those intended could result in a hazardous situation. 10. Have your tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the tool is maintained. 11. Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries. Position batteries in proper polarity. Do not use swollen or leaking batteries. 12. Maintain labels and nameplates on the tool. These carry important safety information. If unreadable or missing, contact Harbor Freight Tools for a replacement. For technical questions, please call 1-888-866-5797. Item 69465 13. This product is not a toy. Keep it out of reach of children. SAFETY 14. The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. MAINTENANCE OPERATION SETUP SAVE THESE INSTRUCTIONS. Item 69465 For technical questions, please call 1-888-866-5797. Page 3 Specifications SAFETY Measurement Range -36ºF to 968ºF (-38ºC to 520ºC) Accuracy ± 2% above 32ºF ± 4.5% below 31ºF Response Time 1 Sec Spot Size Ratio 8:1 (Distance : Spot size) Needed Batteries Two AAA (not included) LASER LIGHT AVOID DIRECT EYE EXPOSURE Max. Output: 0.6 - 0.9 mW, Wavelength: 642 - 658 nm CLASS IIa LASER PRODUCT This product complies with 21 CFR 1040.10 and 1040.11 Distributed by Harbor Freight Tools 3491 Mission Oaks Blvd. Camarillo, CA 93011 69465 17k WARNING To prevent serious injury, do not use for medical purposes. Manufacture Date: Setup - Before Use: SETUP Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Installing the Battery Remove the battery cover and insert two AAA batteries into the unit, following indicated polarity. Replace the battery cover. Functions OPERATION Laser Beam LCD ºF/ºC Button ON/OFF Trigger MAINTENANCE Battery Cover Page 4 For technical questions, please call 1-888-866-5797. Item 69465 Operating Instructions SAFETY Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. General Operating Instructions 2. Push the ºF/ºC button to toggle between Fahrenheit to Celsius, and to recover the last reading when in OFF mode. 3. Squeeze the Trigger and move the laser to see a constant temperature reading and max reading. 4. Release the Trigger to display the most recent temperature reading, or to allow 15 seconds for auto shut off. 2" diameter at 16" distance 3" diameter at 24" distance Distance to Spot Size = 8:1 Field of View 7. When finished, release the Trigger. The last temperature will display for 15 seconds, then the unit will shut off. 8. Clean the lens with dry compressed air and wipe the rest of the unit down with a soft, damp cloth, then store the product indoors out of children’s reach. 9. To prevent accidents, turn off the tool and disconnect its power supply after use. Clean, then store the tool indoors out of children’s reach. MAINTENANCE 5. Non-reflective surfaces will yield a more accurate reading than reflective surfaces. Duct tape (sold separately) can be applied to reflective surfaces in order to get a better measurement. Allow sufficient time for the tape to match the temperature of the surface it is applied to before trying to get a reading. 1" diameter at 8" distance SETUP 1. Squeeze the Trigger to activate the Laser and temperature reading. Distance OPERATION Note: When moving the Thermometer to an area with significantly different ambient temperature, allow the unit to adjust to the new ambient temperature for 30 minutes before use. 6. The object being tested should be larger than the size calculated by the Field of View diagram, below. Spot Center Note: Do not expose this product to strong electromagnetic fields, such as those generated by an arc welder, induction heater, etc. Item 69465 For technical questions, please call 1-888-866-5797. Page 5 Maintenance and Servicing SAFETY Procedures not specifically explained in this manual must be performed only by a qualified technician. TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Release the Trigger and remove the batteries from the Laser Thermometer before performing any inspection, maintenance, or cleaning procedures. TO PREVENT SERIOUS INJURY FROM TOOL FAILURE: Do not use damaged equipment. If damage is noted, have the problem corrected before further use. Cleaning, Maintenance, and Lubrication SETUP 1. BEFORE EACH USE, inspect the general condition of the tool. Check for: 2. AFTER USE, wipe external surfaces of the tool with clean cloth. • loose hardware, • misalignment or binding of parts, • cracked or broken parts, • damaged electrical wiring, and • any other condition that may affect its safe operation. OPERATION PLEASE READ THE FOLLOWING CAREFULLY MAINTENANCE THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. Page 6 For technical questions, please call 1-888-866-5797. Item 69465 Parts List and Diagram Description Front Cover Rear Cover Battery Cover Trigger °F/°C Button LCD Back Light Layered Block PCB Switch Part 11 12 13 14 15 16 17 18 19 20 Description Front Mass Lens RMASS TPI RMASS Thermopile Laser Holder -B Laser Module Negative Plate Positive Plate P-N Plate Part 21 22 23 24 25 26 Description Tapping Screw (M 1.7*5L) Machine Screw (M 2* 4L) Tapping Screw (M 1.7*4L) Tapping Screw (M 2.3*8L) Battery (not included) Pad MAINTENANCE OPERATION SETUP 1 2 3 4 5 6 7 8 9 10 SAFETY Part Item 69465 For technical questions, please call 1-888-866-5797. Page 7 Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS. To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. Record Product’s Serial Number Here: Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. 3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Page Count : 8 Producer : Mac OS X 10.11.6 Quartz PDFContext Create Date : 2017:11:02 00:16:29Z Modify Date : 2017:11:02 00:16:29ZEXIF Metadata provided by EXIF.tools