8085 Instruction Set Instructions
User Manual:
Open the PDF directly: View PDF 
.
Page Count: 15
| Download | |
| Open PDF In Browser | View PDF |
8085 INSTRUCTION SET INSTRUCTION DETAILS DATA TRANSFER INSTRUCTIONS Opcode Operand Copy from source to destination MOV Rd, Rs M, Rs Rd, M Move immediate 8-bit MVI Rd, data M, data Load accumulator LDA 16-bit address Load accumulator indirect LDAX B/D Reg. pair Load register pair immediate LXI Reg. pair, 16-bit data Load H and L registers direct LHLD 16-bit address 8085 Instruction Set Description This instruction copies the contents of the source register into the destination register; the contents of the source register are not altered. If one of the operands is a memory location, its location is specified by the contents of the HL registers. Example: MOV B, C or MOV B, M The 8-bit data is stored in the destination register or memory. If the operand is a memory location, its location is specified by the contents of the HL registers. Example: MVI B, 57 or MVI M, 57 The contents of a memory location, specified by a 16-bit address in the operand, are copied to the accumulator. The contents of the source are not altered. Example: LDA 2034 or LDA XYZ The contents of the designated register pair point to a memory location. This instruction copies the contents of that memory location into the accumulator. The contents of either the register pair or the memory location are not altered. Example: LDAX B The instruction loads 16-bit data in the register pair designated in the operand. Example: LXI H, 2034 The instruction copies the contents of the memory location pointed out by the 16-bit address into register L and copies the contents of the next memory location into register H. The contents of source memory locations are not altered. Example: LHLD 2040 Page 1 Store accumulator direct STA 16-bit address Store accumulator indirect STAX Reg. pair Store H and L registers direct SHLD 16-bit address Exchange H and L with D and E XCHG none The contents of the accumulator are copied into the memory location specified by the operand. This is a 3-byte instruction, the second byte specifies the low-order address and the third byte specifies the high-order address. Example: STA 4350 or STA XYZ The contents of the accumulator are copied into the memory location specified by the contents of the operand (register pair). The contents of the accumulator are not altered. Example: STAX B The contents of register L are stored into the memory location specified by the 16-bit address in the operand and the contents of H register are stored into the next memory location by incrementing the operand. The contents of registers HL are not altered. This is a 3-byte instruction, the second byte specifies the low-order address and the third byte specifies the high-order address. Example: SHLD 2470 The contents of register H are exchanged with the contents of register D, and the contents of register L are exchanged with the contents of register E. Example: XCHG Copy H and L registers to the stack pointer SPHL none The instruction loads the contents of the H and L registers into the stack pointer register, the contents of the H register provide the high-order address and the contents of the L register provide the low-order address. The contents of the H and L registers are not altered. Example: SPHL Exchange H and L with top of stack XTHL none The contents of the L register are exchanged with the stack location pointed out by the contents of the stack pointer register. The contents of the H register are exchanged with the next stack location (SP+1); however, the contents of the stack pointer register are not altered. Example: XTHL 8085 Instruction Set Page 2 Push register pair onto stack PUSH Reg. pair Pop off stack to register pair POP Reg. pair The contents of the register pair designated in the operand are copied onto the stack in the following sequence. The stack pointer register is decremented and the contents of the highorder register (B, D, H, A) are copied into that location. The stack pointer register is decremented again and the contents of the low-order register (C, E, L, flags) are copied to that location. Example: PUSH B or PUSH A The contents of the memory location pointed out by the stack pointer register are copied to the low-order register (C, E, L, status flags) of the operand. The stack pointer is incremented by 1 and the contents of that memory location are copied to the high-order register (B, D, H, A) of the operand. The stack pointer register is again incremented by 1. Example: POP H or POP A Output data from accumulator to a port with 8-bit address OUT 8-bit port address The contents of the accumulator are copied into the I/O port specified by the operand. Example: OUT 87 Input data to accumulator from a port with 8-bit address IN 8-bit port address The contents of the input port designated in the operand are read and loaded into the accumulator. Example: IN 82 8085 Instruction Set Page 3 ARITHMETIC INSTRUCTIONS Opcode Operand Description Add register or memory to accumulator ADD R The contents of the operand (register or memory) are M added to the contents of the accumulator and the result is stored in the accumulator. If the operand is a memory location, its location is specified by the contents of the HL registers. All flags are modified to reflect the result of the addition. Example: ADD B or ADD M Add register to accumulator with carry ADC R The contents of the operand (register or memory) and M the Carry flag are added to the contents of the accumulator and the result is stored in the accumulator. If the operand is a memory location, its location is specified by the contents of the HL registers. All flags are modified to reflect the result of the addition. Example: ADC B or ADC M Add immediate to accumulator ADI 8-bit data The 8-bit data (operand) is added to the contents of the accumulator and the result is stored in the accumulator. All flags are modified to reflect the result of the addition. Example: ADI 45 Add immediate to accumulator with carry ACI 8-bit data The 8-bit data (operand) and the Carry flag are added to the contents of the accumulator and the result is stored in the accumulator. All flags are modified to reflect the result of the addition. Example: ACI 45 Add register pair to H and L registers DAD Reg. pair The 16-bit contents of the specified register pair are added to the contents of the HL register and the sum is stored in the HL register. The contents of the source register pair are not altered. If the result is larger than 16 bits, the CY flag is set. No other flags are affected. Example: DAD H 8085 Instruction Set Page 4 Subtract register or memory from accumulator SUB R The contents of the operand (register or memory ) are M subtracted from the contents of the accumulator, and the result is stored in the accumulator. If the operand is a memory location, its location is specified by the contents of the HL registers. All flags are modified to reflect the result of the subtraction. Example: SUB B or SUB M Subtract source and borrow from accumulator SBB R The contents of the operand (register or memory ) and M the Borrow flag are subtracted from the contents of the accumulator and the result is placed in the accumulator. If the operand is a memory location, its location is specified by the contents of the HL registers. All flags are modified to reflect the result of the subtraction. Example: SBB B or SBB M Subtract immediate from accumulator SUI 8-bit data The 8-bit data (operand) is subtracted from the contents of the accumulator and the result is stored in the accumulator. All flags are modified to reflect the result of the subtraction. Example: SUI 45 Subtract immediate from accumulator with borrow SBI 8-bit data The 8-bit data (operand) and the Borrow flag are subtracted from the contents of the accumulator and the result is stored in the accumulator. All flags are modified to reflect the result of the subtracion. Example: SBI 45 Increment register or memory by 1 INR R M Increment register pair by 1 INX R 8085 Instruction Set The contents of the designated register or memory) are incremented by 1 and the result is stored in the same place. If the operand is a memory location, its location is specified by the contents of the HL registers. Example: INR B or INR M The contents of the designated register pair are incremented by 1 and the result is stored in the same place. Example: INX H Page 5 Decrement register or memory by 1 DCR R The contents of the designated register or memory are M decremented by 1 and the result is stored in the same place. If the operand is a memory location, its location is specified by the contents of the HL registers. Example: DCR B or DCR M Decrement register pair by 1 DCX R Decimal adjust accumulator DAA none The contents of the designated register pair are decremented by 1 and the result is stored in the same place. Example: DCX H The contents of the accumulator are changed from a binary value to two 4-bit binary coded decimal (BCD) digits. This is the only instruction that uses the auxiliary flag to perform the binary to BCD conversion, and the conversion procedure is described below. S, Z, AC, P, CY flags are altered to reflect the results of the operation. If the value of the low-order 4-bits in the accumulator is greater than 9 or if AC flag is set, the instruction adds 6 to the low-order four bits. If the value of the high-order 4-bits in the accumulator is greater than 9 or if the Carry flag is set, the instruction adds 6 to the high-order four bits. Example: DAA 8085 Instruction Set Page 6 BRANCHING INSTRUCTIONS Opcode Operand Description Jump unconditionally JMP 16-bit address The program sequence is transferred to the memory location specified by the 16-bit address given in the operand. Example: JMP 2034 or JMP XYZ Jump conditionally Operand: 16-bit address The program sequence is transferred to the memory location specified by the 16-bit address given in the operand based on the specified flag of the PSW as described below. Example: JZ 2034 or JZ XYZ Opcode JC JNC JP JM JZ JNZ JPE JPO 8085 Instruction Set Description Jump on Carry Jump on no Carry Jump on positive Jump on minus Jump on zero Jump on no zero Jump on parity even Jump on parity odd Flag Status CY = 1 CY = 0 S=0 S=1 Z=1 Z=0 P=1 P=0 Page 7 Unconditional subroutine call CALL 16-bit address The program sequence is transferred to the memory location specified by the 16-bit address given in the operand. Before the transfer, the address of the next instruction after CALL (the contents of the program counter) is pushed onto the stack. Example: CALL 2034 or CALL XYZ Call conditionally Operand: 16-bit address The program sequence is transferred to the memory location specified by the 16-bit address given in the operand based on the specified flag of the PSW as described below. Before the transfer, the address of the next instruction after the call (the contents of the program counter) is pushed onto the stack. Example: CZ 2034 or CZ XYZ Opcode CC CNC CP CM CZ CNZ CPE CPO 8085 Instruction Set Description Call on Carry Call on no Carry Call on positive Call on minus Call on zero Call on no zero Call on parity even Call on parity odd Flag Status CY = 1 CY = 0 S=0 S=1 Z=1 Z=0 P=1 P=0 Page 8 Return from subroutine unconditionally RET none The program sequence is transferred from the subroutine to the calling program. The two bytes from the top of the stack are copied into the program counter, and program execution begins at the new address. Example: RET Return from subroutine conditionally Operand: none The program sequence is transferred from the subroutine to the calling program based on the specified flag of the PSW as described below. The two bytes from the top of the stack are copied into the program counter, and program execution begins at the new address. Example: RZ Opcode RC RNC RP RM RZ RNZ RPE RPO 8085 Instruction Set Description Return on Carry Return on no Carry Return on positive Return on minus Return on zero Return on no zero Return on parity even Return on parity odd Flag Status CY = 1 CY = 0 S=0 S=1 Z=1 Z=0 P=1 P=0 Page 9 Load program counter with HL contents PCHL none The contents of registers H and L are copied into the program counter. The contents of H are placed as the high-order byte and the contents of L as the low-order byte. Example: PCHL Restart RST 0-7 The RST instruction is equivalent to a 1-byte call instruction to one of eight memory locations depending upon the number. The instructions are generally used in conjunction with interrupts and inserted using external hardware. However these can be used as software instructions in a program to transfer program execution to one of the eight locations. The addresses are: Instruction RST 0 RST 1 RST 2 RST 3 RST 4 RST 5 RST 6 RST 7 Restart Address 0000H 0008H 0010H 0018H 0020H 0028H 0030H 0038H The 8085 has four additional interrupts and these interrupts generate RST instructions internally and thus do not require any external hardware. These instructions and their Restart addresses are: Interrupt TRAP RST 5.5 RST 6.5 RST 7.5 8085 Instruction Set Page 10 Restart Address 0024H 002CH 0034H 003CH LOGICAL INSTRUCTIONS Opcode Operand Description Compare register or memory with accumulator CMP R The contents of the operand (register or memory) are M compared with the contents of the accumulator. Both contents are preserved . The result of the comparison is shown by setting the flags of the PSW as follows: if (A) < (reg/mem): carry flag is set, s=1 if (A) = (reg/mem): zero flag is set, s=0 if (A) > (reg/mem): carry and zero flags are reset, s=0 Example: CMP B or CMP M Compare immediate with accumulator CPI 8-bit data The second byte (8-bit data) is compared with the contents of the accumulator. The values being compared remain unchanged. The result of the comparison is shown by setting the flags of the PSW as follows: if (A) < data: carry flag is set, s=1 if (A) = data: zero flag is set, s=0 if (A) > data: carry and zero flags are reset, s=0 Example: CPI 89 Logical AND register or memory with accumulator ANA R The contents of the accumulator are logically ANDed with M the contents of the operand (register or memory), and the result is placed in the accumulator. If the operand is a memory location, its address is specified by the contents of HL registers. S, Z, P are modified to reflect the result of the operation. CY is reset. AC is set. Example: ANA B or ANA M Logical AND immediate with accumulator ANI 8-bit data The contents of the accumulator are logically ANDed with the 8-bit data (operand) and the result is placed in the accumulator. S, Z, P are modified to reflect the result of the operation. CY is reset. AC is set. Example: ANI 86 8085 Instruction Set Page 11 Exclusive OR register or memory with accumulator XRA R The contents of the accumulator are Exclusive ORed with M the contents of the operand (register or memory), and the result is placed in the accumulator. If the operand is a memory location, its address is specified by the contents of HL registers. S, Z, P are modified to reflect the result of the operation. CY and AC are reset. Example: XRA B or XRA M Exclusive OR immediate with accumulator XRI 8-bit data The contents of the accumulator are Exclusive ORed with the 8-bit data (operand) and the result is placed in the accumulator. S, Z, P are modified to reflect the result of the operation. CY and AC are reset. Example: XRI 86 Logical OR register or memory with accumulaotr ORA R The contents of the accumulator are logically ORed with M the contents of the operand (register or memory), and the result is placed in the accumulator. If the operand is a memory location, its address is specified by the contents of HL registers. S, Z, P are modified to reflect the result of the operation. CY and AC are reset. Example: ORA B or ORA M Logical OR immediate with accumulator ORI 8-bit data The contents of the accumulator are logically ORed with the 8-bit data (operand) and the result is placed in the accumulator. S, Z, P are modified to reflect the result of the operation. CY and AC are reset. Example: ORI 86 Rotate accumulator left RLC none Rotate accumulator right RRC none 8085 Instruction Set Each binary bit of the accumulator is rotated left by one position. Bit D7 is placed in the position of D0 as well as in the Carry flag. CY is modified according to bit D7. S, Z, P, AC are not affected. Example: RLC Each binary bit of the accumulator is rotated right by one position. Bit D0 is placed in the position of D7 as well as in the Carry flag. CY is modified according to bit D0. S, Z, P, AC are not affected. Example: RRC Page 12 Rotate accumulator left through carry RAL none Each binary bit of the accumulator is rotated left by one position through the Carry flag. Bit D7 is placed in the Carry flag, and the Carry flag is placed in the least significant position D0. CY is modified according to bit D7. S, Z, P, AC are not affected. Example: RAL Rotate accumulator right through carry RAR none Each binary bit of the accumulator is rotated right by one position through the Carry flag. Bit D0 is placed in the Carry flag, and the Carry flag is placed in the most significant position D7. CY is modified according to bit D0. S, Z, P, AC are not affected. Example: RAR Complement accumulator CMA none Complement carry CMC none Set Carry STC none 8085 Instruction Set The contents of the accumulator are complemented. No flags are affected. Example: CMA The Carry flag is complemented. No other flags are affected. Example: CMC The Carry flag is set to 1. No other flags are affected. Example: STC Page 13 CONTROL INSTRUCTIONS Opcode Operand No operation NOP none Halt and enter wait state HLT none Disable interrupts DI none Enable interrupts EI none 8085 Instruction Set Description No operation is performed. The instruction is fetched and decoded. However no operation is executed. Example: NOP The CPU finishes executing the current instruction and halts any further execution. An interrupt or reset is necessary to exit from the halt state. Example: HLT The interrupt enable flip-flop is reset and all the interrupts except the TRAP are disabled. No flags are affected. Example: DI The interrupt enable flip-flop is set and all interrupts are enabled. No flags are affected. After a system reset or the acknowledgement of an interrupt, the interrupt enable flipflop is reset, thus disabling the interrupts. This instruction is necessary to reenable the interrupts (except TRAP). Example: EI Page 14 Read interrupt mask RIM none Set interrupt mask SIM none 8085 Instruction Set This is a multipurpose instruction used to read the status of interrupts 7.5, 6.5, 5.5 and read serial data input bit. The instruction loads eight bits in the accumulator with the following interpretations. Example: RIM This is a multipurpose instruction and used to implement the 8085 interrupts 7.5, 6.5, 5.5, and serial data output. The instruction interprets the accumulator contents as follows. Example: SIM Page 15
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Page Count : 15 Title : 8085 instruction set Author : Paul Werstein Subject : Apple Keywords : Creator : Microsoft Word Producer : Mac OS X 10.5.2 Quartz PDFContext Create Date : 2008:04:12 03:02:21Z Modify Date : 2008:04:12 03:02:21ZEXIF Metadata provided by EXIF.tools