07050A 07610 Wood Gate_ 88219443 5929 4588 B14e D4c9f0d6130e

User Manual: 07050A

Open the PDF directly: View PDF PDF.
Page Count: 3

Extension Frames (two) Tension Bolts (four)
Extension Pins (four)
Gate Frame
Lower
Latch
Set
Gate Panel
Upper Latch Set
Release
Button
Wrench
INSTRUCTION MANUAL
DELUXE WOOD WALK-THRU GATE
Thank you for buying the Deluxe Wood Walk-Thru Gate from
Summer Infant. This pressure-mounted gate helps you create and
maintain a secure environment for your child. It has a hinged
swinging door that opens easily in either direction with one hand.
It also swings closed automatically. It’s fully adjustable to fit
openings from 29.5"– 40.5".
Please read all the instructions before installing the gate.
07050A, 07610
Please read the following instructions carefully.
Keep this instruction manual for future reference.
Tools required: (none).
For Technical Support Call 1-800-268-6237 or
E-Mail at customerservice@summerinfant.com
WARNING: IMPORTANT! KEEP FOR FUTURE REFERENCE!
CAUTION: KEEP SMALL PARTS OUT OF CHILD’S REACH.
• To prevent serious injury or death, securely install gate and use according to manufacturer’s instructions.
• Never use with a child able to climb over or dislodge the gate.
• Never leave child unattended.
• Use only with lock securely engaged.
• Do not use if any components are missing or damaged.
• To prevent falls never use at top of stairs.
• This product will not necessarily prevent all accidents. Proper adult supervision is required at all times.
WARNING:
Adult assembly required.
Exercise care when unpacking and assembling product.
For use with children six months and up.
FEATURES & COMPONENTS:
SET UP:
OPERATION:
To open the gate: (see Figure N)
1. Slide the release button away from the door frame or wall.
2. Lift up the gate panel.
3. Swing open in either direction.
To close the gate:
Simply release the gate and it will
close automatically.
Caution: After closing the gate,
ALWAYS check to be certain that
it is latched securely.
Troubleshooting:
If the gate does not stay closed:
1. The upper latch set is not properly adjusted.
Solution: Adjust the upper tension knobs by turning them counter-clockwise to
release tension or clockwise to increase tension. Ensure that the upper latch set
button always remains below the release button as shown in Figure L. Also
ensure that the upper latch set button engages securely when the gate swings
closed and that it can be released properly when the release button is pushed.
2. L
ower latch set position is too low.
Solution:
Although unusual, some door
frames may be out of alignment. In this case
you may have to adjust the individual tension
knobs to ensure that the gate is aligned
properly. Make sure the upper latch set is still
below the release button as shown in Figure L.
If the gate does not stay in position it may
not be installed properly as shown in
Figure O. Remove and reinstall the gate,
making sure the gate is installed
correctly as shown in Figure O.
1. Regularly check tension knobs and rubber pads to make sure
the gate is securely in place.
2. Do not use the gate if any components are damaged or missing.
3. Wipe surface with a damp cloth or sponge using mild detergent
and warm water.
2
To use with extension frame
assemble as shown in Figure D.
1
Measure the width of the opening where you intend to install the
gate. Please refer to the following pictures to determine the correct
installation configuration.
4
Place the gate in the opening so that the
bottom of the gate frame is completely flat on
the floor, as shown in Figure E.
3
Screw the tension knobs
down the tension bolts until they
contact the pads. Insert 4 tension
bolts into holes on outside and
slide inward towards frame as far
as possible.
6
Tighten both of the tension knobs on the bottom inward towards
the frame at the same time, as shown in Figure I. Then tighten both of the
tension knobs on the top inward towards the frame at the same time, as
shown in Figure J, so that the upper latch set goes below the release
button completely, as shown in Figure L. To verify installation: Push the
frame to ensure that it is secure in the opening and then push the gate
panel to ensure that the upper and lower latch sets lock securely in the
housings on the frame, as shown in Figures K and L.
(29.5" – 33")
without Extension Frame
(33" – 371/2")
with Extension Frame
Note:
If gate is difficult to unlatch, top tension knobs may be too tight.
Note: Wrench is provided for final tightening of all
four tension knobs (if necessary), as shown
in Figure H.
(371/2" – 40.5")
with Extension Frame
A FIGURE
Long end of
Extension Pin
Tension
Knob
Tension
Bolt
Extension
Frame
Gate
Frame
D FIGURE
E FIGURE
side view
top view
O FIGURE
5
Center the gate in the opening, so that the distance from the bottom
of gate frame to each side wall is equal, as shown in Figure F.
Note: Never
create a gap on either side more than 3”.
Use the marks etched into the
wrench as a ruler. Slide the tension bolts out until the pads contact the door
frame or wall. Then screw the tension knob away from the pad until it contacts
the gate frame as shown in Figure G.
tighten
inward
Distance should be equal
F FIGURE G FIGURE
B FIGURE
Pad
Release Button
Upper Latch Set
Tighten inward at the same time
Tighten inward at the same time
I FIGURE J FIGURE
L FIGURE K FIGURE
Lower Latch Set
C FIGURE
M
FIGURE
MAINTENANCE:
To install with mounting cups:
Fasten mounting cups to the door frame or studs with
screws as shown in Figure M. If mounting into wall,
use wall anchors.
Note:
The adhesive mounting pads are only for
positioning the mounting cups and must be used in
conjunction with screws.
OPTIONAL MOUNTING CUPS:
In normal use, there is no need for mounting holes that damage
woodwork and walls. For added security, optional mounting cup kit,
item #07050A-1 can be ordered on www.summerinfant.com
H FIGURE
N
FIGURE
9/07
We at Summer Infant stand behind all of
our products. If you are not completely
satisfied or have any questions, please
contact ourCustomer Service Department
at 1-800-268-6237 or e-mail us at
customerservice@summerinfant.com
© 2002 Summer Infant, Inc.
1275 Park East Drive
Woonsocket, RI 02895 USA
1-800-268-6237
MADE IN CHINA.
Colors and styles may vary.
Summer Infant Europe, LTD.
Office Suite 6, Second Floor
Bournehall House, Bournehall Road
Bushey, Hertfordshire
WD23 3HP UK
+44 (0)208 420 4429
DELUXE WOOD WALK-THRU GATE
07230, 07050A, 07610
To create tension against the walls of the opening,
turn the knob on each tension bolt with the wrench
provided until the gate is snug.
Follow steps on the instruction sheet carefully and the
installation should go smoothly. If you have any problems,
please do not return the gate to the store where you
purchased it. Call our customer service line at 1-800-268-6237
and someone should be able to help you with installation. If
you are an international customer, please email us at
customerservice@summerinfant.com.
The 4 tension bolts, with adjusting knobs,
simply slide into the gate frame–they do NOT
screw into place.
What to expect from your Summer Infant
Deluxe Wood Pressure Gate
Please read these helpful hints in
addition to reading your instruction
manual carefully.
It is manufactured at a pre-set angle so
that when it is installed in an opening
properly, it will mantain the correct
amount of tension and cannot be pushed
out of the opening under normal use.
When you unpack the gate, you will notice it
is NOT square. This is normal and not
damage to the gate.
9/07
Summer Infant, Inc.
1275 Park East Drive
Woonsocket, RI 02895 USA
1-800-268-6237
©2002 Summer Infant, Inc.
Summer Infant Europe, LTD.
Office Suite 6, Second Floor
Bournehall House, Bournehall Road
Bushey, Hertfordshire WD23 3HP UK
+44 (0)20 8420 4429

Navigation menu