Manual For The 98328 Tile Saw Stand With Wheels
User Manual: Manual for the 98328 Tile Saw Stand with Wheels Tile Saw Stand with Wheels
Open the PDF directly: View PDF 
.
Page Count: 7
TILE SAW STAND
Model
98328
SET UP AND OPERATING INSTRUCTIONS
Tile Cutting Saw shown in above photo is for display purpose only and is not included with this Tile Saw Stand.
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
Distributed exclusively by Harbor Freight Tools®.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Copyright© 2008 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
Page 2SKU 98328 For technical questions, please call 1-800-444-3353.
SAVE THIS MANUAL
Keep this manual for the safety warn-
ings and precautions, assembly, operat-
ing, inspection, maintenance and cleaning
procedures. Write the product’s serial
number in the back of the manual near the
assembly diagram (or month and year of
purchase if product has no number). Keep
this manual and the receipt in a safe and
dry place for future reference.
IMPORTANT SAFETY
INFORMATION
In this manual, on the labeling, and all other
information provided with this product:
This is the safety alert
symbol. It is used to alert
you to potential personal
injury hazards. Obey all
safety messages that
follow this symbol to avoid
possible injury or death.
DANGER indicates
a hazardous
situation which, if
not avoided, will result in
death or serious injury.
WARNING
indicates a
hazardous
situation which, if not
avoided, could result in death
or serious injury.
CAUTION, used
with the safety
alert symbol,
indicates a hazardous
situation which, if not
avoided, could result in minor
or moderate injury.
NOTICE is used to
address practices
not related to
personal injury.
CAUTION, without
the safety alert
symbol, is used to
address practices not related
to personal injury.
GENERAL AND SPECIFIC
SAFETY WARNINGS
WARNING Read all safety warnings and
instructions. Failure to follow the warnings and
instructions may result in serious injury. Save all
warnings and instructions for future reference.
Work area safety
Keep work area clean and well lit. 1.
Cluttered or dark areas invite acci-
dents.
Wear ANSI-approved safety goggles 2.
during assembly, setup and use of
this Tile Saw Stand.
3.
or hands in scissor action of Tile Saw
-
folding to use, or store after use.
Keep children and bystanders away 4.
while operating. Distractions can
cause you to lose control.
Stay alert, watch what you are doing 5.
and use common sense when operat-
ing. Do not use while you are tired
Page 3SKU 98328 For technical questions, please call 1-800-444-3353.
or under the inuence of drugs,
alcohol or medication. A moment
of inattention may result in serious
personal injury.
Store out of the reach of children and 6.
do not allow persons unfamiliar to
operate. Tools are dangerous in the
hands of untrained users.
Use the Tile Saw Stand in accor-7.
dance with these instructions, taking
into account the working conditions
and the work to be performed. Use
of the Tile Saw Stand for operations
different from those intended could
result in a hazardous situation.
Read and follow all manufacturer’s 8.
safety warnings, set-up instructions,
and operating procedures for the tile
saw you are using with this Tile Saw
Table.
SAVE THESE
INSTRUCTIONS.
SPECIFICATIONS
Construction
Stand and Brackets: Formed
Sheeted Steel.
Wheels: Polyethylene.
Locking Knobs: Polystyrene.
Mounting Hardware: Carbon
Steel:
Washers: Thermoplastic
NOTE: This Stand is ONLY to be used
with Bridge Tile Saw, SKU 98265.
available at Harbor Freight Tools.
UNPACKING
When unpacking, check to make sure
that the item is intact and undamaged. If
any parts are missing or broken, please
call Harbor Freight Tools at the number
shown on the cover of this manual as soon
as possible.
Note: For additional information regarding
the parts listed in the following pages,
refer to the Assembly Diagram near
the end of this manual.
ASSEMBLY
Insert Upper Support A (1) and B (5) 1.
into Lower Support A (3) and B (12)
and secure with a Lock Knob (2) on
each side.
Attach both supports together using 2.
Combination Plates A (8) and B (11).
Insert one Shaft (6) through a Washer
(19) and into the Upper Support (A).
Insert one Spacer (7) and push the
Shaft through Combination Plate A
(8). Insert the second Spacer (7) and
push the Shaft through Upper Sup-
port B (5). Attach a Washer (9) and
Lock-Nut (10). Finger-tighten the
Lock-Nut only.
Repeat the above mentioned proce-3.
dure for the opposite side. Tighten
the Lock-Nuts (10) until the Combina-
tion Plates (A and B) can be rocked
slightly.
Mount one Wheel (18) on end of Axle 4.
(20) and attach one Wheel Support
(A and B) (17 and 21), to Axle (20)
outside of Wheels (18). Attach Wheel
Supports (A and B) (17 and 21) to
each side of Lower Supports (A and
B). Use included Hardware:
Screw (13),a.
Flat Washer (14),b.
Lock-Nut (15), andc.
Page 4SKU 98328 For technical questions, please call 1-800-444-3353.
Retainer (16), to secure Wheels d.
(18).
Attach four Rubber Feet (4) to ends 1.
of each Lower Support Foot.
Attach one Mounting Knob (22) to 2.
threaded holes in each Lower support
Foot.
Use remaining Lock Knobs (2) to se-3.
cure base of tile saw to this Tile Saw
Stand.
See 4. Assembly Diagram on page 6
of this manual.
OPERATING INSTRUCTIONS
Read the ENTIRE
IMPORTANT SAFETY
INFORMATION section at the
beginning of this manual
including all text under
subheadings therein before set
up or use of this product.
1.
surface able to support the weight of
the Tile Saw Stand and the tile saw
attached to it.
Attach your tile saw and secure base 2.
to Tile Saw Stand with Lock Knobs
(2).
To move Tile Saw Stand (with or with-3.
out tile saw attached), tilt the Stand
forward on it’s wheels and push to
new position.
4.
fold the Tile Saw Stand and store
inside.
MAINTENANCE AND
SERVICING
BEFORE EACH USE,1. inspect the
general condition of the tool. Check
condition that may affect its safe
operation.
AFTER USE,2. wipe external surfaces
of the tool with clean cloth.
Store the Tile Saw Stand in dry area 3.
inside and away from children.
PLEASE READ THE FOLLOW-
ING CAREFULLY
HAS PROVIDED THE PARTS LIST AND
ASSEMBLY DIAGRAM IN THIS MANUAL AS
A REFERENCE TOOL ONLY. NEITHER THE
MANUFACTURER OR DISTRIBUTOR MAKES
ANY REPRESENTATION OR WARRANTY OF
ANY KIND TO THE BUYER THAT HE OR SHE
IS QUALIFIED TO MAKE ANY REPAIRS TO THE
PRODUCT, OR THAT HE OR SHE IS QUALIFIED
TO REPLACE ANY PARTS OF THE PRODUCT.
DISTRIBUTOR EXPRESSLY STATES THAT
ALL REPAIRS AND PARTS REPLACEMENTS
SHOULD BE UNDERTAKEN BY CERTIFIED
AND LICENSED TECHNICIANS, AND NOT BY
THE BUYER. THE BUYER ASSUMES ALL RISK
AND LIABILITY ARISING OUT OF HIS OR HER
REPAIRS TO THE ORIGINAL PRODUCT OR
REPLACEMENT PARTS THERETO, OR ARISING
OUT OF HIS OR HER INSTALLATION OF
REPLACEMENT PARTS THERETO.
Page 5SKU 98328 For technical questions, please call 1-800-444-3353.
PARTS LIST
Part # Description Q’ty
1 Upper Support (A) 1
2 Lock Knob 8
3 Lower Support (A) 1
4 Feet 4
5 Upper Support (B) 1
6 Shaft 2
7 Spacer 10 4
8 Combination Plate (A) 1
9 Flat Washer 8 2
10 Lock-Nut 2
11 Combination Plate (B) 1
12 Lower Support (B) 1
13 Screw M6 X 40 4
14 Flat Washer 6 8
15 Lock-Nut M6 4
16 Retainer 10 4
17 Wheel Support (A) 1
18 Wheel 2
19 Flat Washer 10 2
20 Axle 1
21 Wheel Support (B) 1
22 Mounting Knob 4
Page 6SKU 98328 For technical questions, please call 1-800-444-3353.
ASSEMBLY DIAGRAM
Page 7SKU 98328 For technical questions, please call 1-800-444-3353.
LIMITED 90 DAY WARRANTY
Harbor Freight Tools Co. makes every effort to assure that its products meet high
quality and durability standards, and warrants to the original purchaser that this prod-
uct is free from defects in materials and workmanship for the period of 90 days from
the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities,
criminal activity, improper installation, normal wear and tear, or to lack of maintenance.
We shall in no event be liable for death, injuries to persons or property, or for incidental,
contingent, special or consequential damages arising from the use of our product. Some
states do not allow the exclusion or limitation of incidental or consequential damages, so
the above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESS-
LY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE
WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with
transportation charges prepaid. Proof of purchase date and an explanation of the com-
-
ther repair or replace the product at our election or we may elect to refund the purchase
price if we cannot readily and quickly provide you with a replacement. We will return re-
paired products at our expense, but if we determine there is no defect, or that the defect
resulted from causes not within the scope of our warranty, then you must bear the cost
of returning the product.
which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only, and are not
available individually as replacement parts.
