AL 1611/1622 Service Manual GB AL1611

User Manual: AL1611

Open the PDF directly: View PDF .
Page Count: 140

Download
Open PDF In Browser	View PDF

q SERVICE MANUAL
CODE : 00ZAL1622//A1E

DIGITAL COPIER
AL-1611

MODEL

AL-1611
AL-1622

AL-1622

CONTENTS

[ 1 ] GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1
[ 2 ] SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 1
[ 3 ] CONSUMABLE PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 1
[ 4 ] EXTERNAL VIEWS AND INTERNAL STRUCTURE . . . . . . . . 4 - 1
[ 5 ] UNPACKING AND INSTALLATION. . . . . . . . . . . . . . . . . . . . . 5 - 1
[ 6 ] OPERATIONAL DESCRIPTIONS . . . . . . . . . . . . . . . . . . . . . . 6 - 1
[ 7 ] ADJUSTMENTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 1
[ 8 ] SIMULATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 1
[ 9 ] USER PROGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 1
[10] TROUBLE CODE LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 1
[11] DISASSEMBLY AND ASSEMBLY. . . . . . . . . . . . . . . . . . . . . 11 - 1
[12] FLASH ROM VERSION UP PROCEDURE . . . . . . . . . . . . . . 12 - 1
[13] ELECTRICAL SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 - 1
[14] CIRCUIT DIAGRAM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 - 1
[15] ACTUAL WIRING DIAGRAM. . . . . . . . . . . . . . . . . . . . . . . . . 15 - 1
[16] SPF PARTS ARRANGEMENT . . . . . . . . . . . . . . . . . . . . . . . 16 - 1

Parts marked with "!" are important for maintaining the safety of the set. Be sure to replace these parts with specified
ones for maintaining the safety and performance of the set.

SHARP CORPORATION

This document has been published to be used
for after sales service only.
The contents are subject to change without notice.

CAUTION
This product is a class 1 laser product that complies with 21CFR 1040.10 and 1040.11 of the CDRH standard and IEC825. This means that this
machine does not produce hazardous laser radiation. The use of controls, adjustments or performance of procedures other than those specified
herein may result in hazardous radiation exposure.
This laser radiation is not a danger to the skin, but when an exact focusing of the laser beam is achieved on the eye’s retina, there is the danger of
spot damage to the retina.
The following cautions must be observed to avoid exposure of the laser beam to your eyes at the time of servicing.
1) When a problem in the laser optical unit has occurred, the whole optical unit must be exchanged as a unit, not as individual parts.
2) Do not look into the machine with the main switch turned on after removing the developer unit, toner cartridge, and drum cartridge.
3) Do not look into the laser beam exposure slit of the laser optical unit with the connector connected when removing and installing the optical
system.
4) The middle frame contains the safety interlock switch.
Do not defeat the safety interlock by inserting wedges or other items into the switch slot.

Warning!
This product is a class A product.
If it is operated in households, offices or similar surroundings, it can produce radio interferences at other
appliances, so that the user has to take adequate countermeasures.
VAROITUS!

CLASS 1 LASER PRODUCT

LAITTEEN KÄYTTÄMINEN MUULLA KUIN TÄSSÄ
KÄYTTÖOHJEESSA MAINITULLA TAVALLA SAATTAA
ALTISTAA KÄYTTÄJÄN TURVALLISUUSLUOKAN 1
YLITTÄVÄLLE NÄKYMÄTTÖMÄLLE
LASERSÄTEILYLLE.

LASER KLASSE 1

LUOKAN 1 LASERLAITE

VARNING
OM APPARATEN ANVÄNDS PÅ ANNAT SÄTT ÄN I
DENNA BRUKSANVISNING SPECIFICERATS, KAN
ANVÄNDAREN UTSÄTTAS FÖR OSYNLIG
LASERSTRÅLNING, SOM ÖVERSKRIDER GRÄNSEN
FÖR LASERKLASS 1.

KLASS 1 LASERAPPARAT

CAUTION

VARO !

VARNING !

INVISIBLE LASER RADIATION,

AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET

WHEN OPEN AND INTERLOCKS DEFEATED. AVOID

ALTTIINA NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE ÄLÄ

ÖPPNAD OCH SPÄRREN ÄR URKOPPLAD. BETRAKTA EJ

EXPOSURE TO BEAM.

KATSO SÄTEESEEN.

STRÅLEN. – STRÅLEN ÄR FARLIG.

VORSICHT

OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR

ADVARSEL

UNSICHTBARE LASERSTRAHLUNG,

USYNLIG LASERSTRÅLNING VED ÅBNING, NÅR

WENN ABDECKUNG GEÖFFNET UND

SIKKERHEDSBRYDERE ER UDE AF

SICHERHEITSVERRIEGELUNG ÜBERBRÜCKT. NICHT

FUNKTION. UNDGÅ UDSAETTELSE FOR

DEM STRAHL AUSSETZEN.

STRÅLNING.

Laserstrahl

LASERSTR LING N R DEKSEL PNES OG SIKKERHEDSL S BRYTES.
INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS DEFEATED.
CAUTION AVOID
UNNG EKSPONERING FOR STR LEN.
ADVERSEL USYNLIG
EXPOSURE TO BEAM.
OSYNLIG LASERSTR LNING N R DENNA DEL R …PPNAD OCH SP RRAR R
LASERSTRAHLUNG WENN ABDECKUNG GE…FFNET UND
VORSICHT UNSICHTBARE
SICHERHEITSVERRIEGELUNG †BERER†CKT. NICHT DEM STRAHL AUSSETZEN. VARNING URKOPPLADE. STR LEN R FARLIG. BETRAKTA EJ STR LEN.
JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA N KYM T…NT
LASERSTR LING VED BNING, N R SIKKERHEDSAFBRYDERE ER
ADVARSEL USYNLIG
VARO! AVATTAESSA
LASERS TEILYLLE. L KATSO S TEESEEN.
UDE AF FUNKTION. UNDGA UDSAETTELSE FOR STR LING.

CLASS 1
LASER PRODUCT
LASER KLASSE 1

LASER WAVE – LENGTH : 785 ± 10 mm
Pulse times : (8.141 ms ± 0.1 ms) / 7 mm

Disconnect the AC cord before servicing the unit.
AL-1611/AL-1622

Out put power : 0.22 mW ± 0.01 mW

CONTENTS
[ 1 ] GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1

[ 8 ] SIMULATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 1

1. GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1

1. ENTERING THE SIMULATION MODE . . . . . . . . . . . . 8 - 1

2. TARGET USER COPY VOLUME:
MONTHLY AVERAGE . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1

2. CANCELLING THE SIMULATION MODE . . . . . . . . . . 8 - 1

3. MAIN FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1

4. CONTENTS OF SIMULATIONS. . . . . . . . . . . . . . . . . . 8 - 2

4. COPIER INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . 1 - 1

[ 9 ] USER PROGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 1

3. LIST OF SIMULATIONS . . . . . . . . . . . . . . . . . . . . . . . . 8 - 1

[ 2 ] SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 1

1. LIST OF USER PROGRAMS . . . . . . . . . . . . . . . . . . . . 9 - 1

1. COPY MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 1

2. SETTING THE USER PROGRAMS . . . . . . . . . . . . . . . 9 - 2

[ 3 ] CONSUMABLE PARTS . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 1

3. TONER CARTRIDGE LIFE . . . . . . . . . . . . . . . . . . . . . 9 - 2

1. SUPPLY SYSTEM TABLE . . . . . . . . . . . . . . . . . . . . . . 3 - 1

[10] TROUBLE CODE LIST . . . . . . . . . . . . . . . . . . . . . . . . 10 - 1

2. ENVIRONMENT CONDITIONS . . . . . . . . . . . . . . . . . . 3 - 1

1. TROUBLE CODE LIST . . . . . . . . . . . . . . . . . . . . . . . . 10 - 1

3. PRODUCTION NUMBER IDENTIFICATION . . . . . . . . 3 - 2

[ 4 ] EXTERNAL VIEWS AND INTERNAL
STRUCTURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 1

2. DETAILS OF TROUBLE CODES . . . . . . . . . . . . . . . . 10 - 1

[11] DISASSEMBLY AND ASSEMBLY . . . . . . . . . . . . . . 11 - 1
1. HIGH VOLTAGE SECTION/
DUPLEX TRANSPORT SECTION . . . . . . . . . . . . . . . 11 - 1

1. APPEARANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 1
2. INTERNAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 1

2. OPTICAL SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . 11 - 2

3. OPERATION SECTION . . . . . . . . . . . . . . . . . . . . . . . . 4 - 2

3. FUSING SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 - 3

4. MOTOR, SOLENOID, CLUTCH . . . . . . . . . . . . . . . . . . 4 - 3

4. PAPER EXIT SECTION . . . . . . . . . . . . . . . . . . . . . . . 11 - 5

5. SENSOR, SWITCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 4

5. MCU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 - 6

6. PWB UNIT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 5

6. OPTICAL FRAME UNIT . . . . . . . . . . . . . . . . . . . . . . . 11 - 7

7. SPF UNIT  . . . . . . . . . . . . . . . . . . . . 4 - 6

7. LSU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 - 7

8. PAPER FEED SECTION . . . . . . . . . 4 - 6
9. CROSS SECTIONAL VIEW . . . . . . . . . . . . . . . . . . . . . 4 - 7

8. TRAY PAPER FEED SECTION/
PAPER TRANSPORT SECTION . . . . . . . . . . . . . . . . 11 - 8

[ 5 ] UNPACKING AND INSTALLATION . . . . . . . . . . . . . . 5 - 1

9. MANUAL MULTI PAPER FEED SECTION . . . . . . . . 11 - 9

1. CHECKING PACKED COMPONENTS
AND ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 1

10. POWER SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . 11 - 11

2. UNPAKING PROCEDURE . . . . . . . . . . . . . . . . . . . . . . 5 - 1

[12] FLASH ROM VERSION UP PROCEDURE . . . . . . . 12 - 1

11. SPF SECTION  . . . . . . . . . . . . . . 11 - 12

3. INSTALLING PROCEDURE . . . . . . . . . . . . . . . . . . . . . 5 - 1

1. MCU/E-SORT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 - 1

4. CHANGING THE COPY PAPER SIZE
IN THE TRAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 3

[ 6 ] OPERATIONAL DESCRIPTIONS . . . . . . . . . . . . . . . . 6 - 1

2. PRINTER CONTROL PWB FIRMWARE
VERSION UP  . . . 12 - 1

[13] ELECTRICAL SECTION . . . . . . . . . . . . . . . . . . . . . . . 13 - 1

1. OUTLINE OF OPERATION . . . . . . . . . . . . . . . . . . . . . 6 - 1

1. BLOCK DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 - 1

2. SCANNER SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 1
3. PROCESS SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 2

2. SPF (AL-1622 ONLY) BLOCK DIAGRAM . . . . . . . . . 13 - 2

[14] CIRCUIT DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 - 1

4. LASER UNIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 5

1. INTERFACE PWB . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 - 1

5. PAPER FEED SECTION . . . . . . . . . . . . . . . . . . . . . . . 6 - 6
6. FUSING SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 7

2. SENSOR PWB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 - 2

[15] ACTUAL WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . 15 - 1

7. SPF SECTION . . . . . . . . . . . . . . . . . 6 - 8

1. ACTUAL WIRING DIAGRAM 1/4 . . . . . . . . . . . . . . . . 15 - 1

[ 7 ] ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 1

2. ACTUAL WIRING DIAGRAM 2/4 . . . . . . . . . . . . . . . . 15 - 2

1. ADJUSTMENT ITEM LIST . . . . . . . . . . . . . . . . . . . . . . 7 - 1

3. ACTUAL WIRING DIAGRAM 3/4 . . . . . . . . . . . . . . . . 15 - 3

2. COPIER ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . 7 - 1

4. ACTUAL WIRING DIAGRAM 4/4 . . . . . . . . . . . . . . . . 15 - 4

[16] SPF PARTS ARRANGEMENT . . . . . . . . . . . . . . . . . 16 - 1

AL-1611/AL-1622

[ 1 ] GENERAL
1. GENERAL

4. COPIER INSTALLATION

This model is a digital personal copier produced with key words of
"Comfort able copy, Clear copy, Easy copy" providing high copy performances and copy productivity.

Do not install your copier in areas that are:
• damp, humid, or very dusty
• exposed to direct sunlight
• poorly ventilated

2. TARGET USER COPY VOLUME: MONTHLY
AVERAGE

• subject to extreme temperature or humidity changes, e.g., near an air
conditioner or heater.

2000~3000 sheets

• Be sure to allow the required space around the machine for servicing
and proper ventilation.

3. MAIN FEATURES
A. HIGH-SPEED LASER COPYING

4" (10 cm)

• First-copy time is only 7.4 seconds (normal mode).
• Copying speed is 16 copies/min., which adapts to business use,
allowing improvement of working efficiency.

B. HIGH-QUALITY DIGITAL IMAGE
• High-quality copying at 600 dpi is performed.
• In addition to the automatic exposure mode, the manual exposure
can be adjusted in five steps.
• The photo mode copying function allows clear copying of delicate
halftone original images such as monochrome photos and color photos. Photo mode is adjustable in five steps.

C. SUBSTANTIAL COPYING FEATURES
• Zoom copying from 50% to 200% in 1% increments can be performed.
• Continuous copying of maximum 99 sheets can also be performed.
• Toner save mode reduces toner consumption by approximately 10%.
• User programs allow setting/modification of functions for customer
needs.

D. SCAN ONCE/ PRINT MANY
• The copier is equipped with a 1-page memory buffer. This memory
allows the copier to scan an original 1 time only and make up to 99
copies. This feature allows for improved workflow, reduced operating
noise from the copier and reduced wear and tear on the scanning
mechanism, which provides for a higher reliability.

E. ENVIRONMENTALLY FRIENDLY DESIGN
• Paper output tray is housed in the copier for space saving.
• Preheat mode and auto power shut-off mode are provided to reduce
power consumption in standby mode.

AL-1611/AL-1622

1–1

GENERAL

[ 2 ] SPECIFICATIONS
1. COPY MODE
A. Type

F. Paper feed

Type

Desk-top

B. Machine composition
AR-1611

16-CPM standard model

AR-1622

16-CPM (with SPF)

Copy size
(Max. ~ Min.)

A3 ~ A6

Paper feed
system

AR-1611

1 cassette + Multi manual paper
feed

AR-1622

2 cassette + Multi manual paper
feed

AR-1611

250 x 1(paper feed tray) + 100
(Multi bypass feed tray)

AR-1622

250 x 2(Paper feed tray) + 100
(Multi bypass feed tray)

Cassette
section

Empty detection available, size
detection by key input

Manual tray

Only empty detection available

Paper feed
capacity

C. Copy speed
(1) Scan One Print many
Not available

Remaining
quantity detection

Condition: Copy speed in the normal copy from all the paper feed ports
including the manual paper feed port.

(1) Paper feed section of the copier
(2) Continuous copy speed (Sheets/min)
Normal

Enlargement
(200%)

Reduction
(50%)

A3

9

9

9

B4

10

10

10

A4

16

16

14

A4R

12

12

12

B5

16

16

16

Paper size

AB
system

D. First copy time
7.2sec (A4, 1st tray/with OC)

E. Document
Max.
document size

A3

Document
Left side center
reference position
Detection (Platen) AR-1611
AR-1622
Detection size

A3, B4, A4, A4R, B5, B5R, A5
(For A5 only No. 1 tray available.)

Side front

Front

Paper feed
capacity

250 sheets (56 ~ 80g/m2 equivalent)

Detection

Paper empty detection available, size detection
(by key input)

Weight

56 ~ 80g/m2

Special paper

Recycled paper

(2) Manual paper feed section

(1) Basic speed
First copy time

Paper feed size

Paper feed size

A3 ~ A6

Paper feed
capacity

100 sheets

Detection

Size detection not available, paper empty detection available

Weight

56 ~ 128g/m2

Special paper

Recycled paper, OHP film, labels

Paper feed

Single except for recycled paper

None

G. Job speed

Available

S-S (1st step)

A3, B4, A4, A4R, B5, B5R, A5

100% (document replacement rate)

Condition: With SPF

(1) SPF (AL-1622 only)
Document load
capacity

30 sheets (56 ~ 90g/m2 equivalent)

H. Multi copy
Max. number of
multi copy

Document
A3 ~ A5
size (Max. ~ Min.)
Document
replacement
speed

16 sheets/min (A4 normal copy)

I. Warmup time

Document set
Face up, Center reference, Paper feed from the
/Paper feed direc- top
tion
Document weight

56 ~ 90g/m2

Document size
detection

On the document feed tray

99 sheets

Warmup time

Approx. 35 sec *

Pre-heat

Available

* May vary depending on the surrounding temperature

Document mixture Copy mode: Not Available
AL-1611/AL-1622

SPECIFICATIONS

2–1

J. Copy magnification ratio

O. Other specifications

Fixed magnification ratio

50, 70, 81, 86, 100, 115, 122, 141, 200%

Zooming

50 ~ 200%

Independent zooming
(vertical)

Available (50 ~ 200%)

Independent zooming
(horizontal)

Available (50 ~ 200%)

K. Print density

Photoconductor
type

OPC (Organic Photo Conductor)

Photoconductor
drum dia.

30mm

Copy lamp

Xenon lamp

Developing
system

Dry 2-component magnetic brush development

Charging system

Saw teeth charging

Transfer system

(+) DC corotron

Density mode

Auto/Manual/Photo

No. of manual adjustment

5 steps (Manual/Photo)

Separation
system

(−) DC corotron

Toner save mode

Set by the user program

Fusing system

Heat roller

Cleaning system

Contact blade

L. Void width
Void area

Lead edge 1 ~ 4mm, rear edge 4mm or less
(Duplex 4mm or less), both sides 4mm or less

Image loss

Max. 4mm in total of lead edge and rear edge,
max. 4mm in total of right and left edges (Normal
copy)

P. Package form
Body

Q. External view
External dimen- 590 × 531 × 470mm (AL-1611)
sions (W × D × H) 590 × 531 × 650mm (AL-1622)

M. Paper exit/finishing
Paper exit section capacity Face down 250 sheets
Job separator

None

Full detection

Available (Job separator upper step)

Offset function

None

Staple function

None

F

Available for only AL-1622

×

(AL-1611)

AMS*

F

(AMS not available by flowing in
during use of SPF)

Duplex

×

Document count

×

Sorter

×

Independent zooming

F

Vertical/Horizontal: 50 ~ 200%

1 set 2 copy

F

Enlargement inhibited, inhibited
during the use of SPF

Binding margin

×

Edge erase

×

Black-white reversion

F

2 in 1, 4 in 1

×

Rotation copy

×

Memory copy

F

Pre-heat function

F

Conditions set by the user program

Auto power shut off function

×

Conditions set by the user program

Auto tray switching

F

Available for only AL-1622

×

(AL-1611)

APS

Message display

×

User program

F

Total counter

F

Occupying area
(W × D)

590 × 531mm (When the manual tray is installed.)

Weight

About 32kg (AL-1611)
About 40kg (AL-1622)

R. Power source

N. Additional functions
*

Body/Accessaries

Voltage

AC120V, 220V, 230V, 240V ±15%

Frequency

50/60Hz common

S. Power consumption
Max. power
consumption

About 1.3KWh

* EnergyStar standard (The 2nd level conformity)
Pre-heat

About 60Wh

Auto power shut
off

0wh.

T. Digital performance
Resolution

Whole surface only

Gradation

F : Available
× : Not available
* : By the document size set key
AL-1611/AL-1622

SPECIFICATIONS

2–2

Reading

400 dpi

Writing

600 dpi

Reading

256 gradations

Writing

Binary

[ 3 ] CONSUMABLE PARTS
1. SUPPLY SYSTEM TABLE
A. Europe
No.

Name

1

Developer cartridge (Black)

2

Drum cartridge

Content
Toner/developer cartridge
Toner:
Net weight 300g
Developer: Net weight 395g

×1

Vinyl bag

×1

Drum cartridge

Life

Product name Package

9K

AL-161TD

4

30K

AL-160DR

4

Remark
Life setting by A4 5%
documents

Note: Maintenance parts other than mentioned above must be ordered through the parts department using the proper part number.

2. ENVIRONMENT CONDITIONS
A. Transport condition

B. Use conditions

Humidity (%)

Humidity (%)

(1) Transport conditions

Use environment
conditions

Temperature
Temperature

C. Life (packed conditions)

(2) Storage conditions (packed conditions)

Humidity (%)

Photoconductor drum (36 months from the production month)
Developer, toner (24 months from the production month)

Temperature

AL-1611/AL-1622

CONSUMABLE PARTS

3–1

3. PRODUCTION NUMBER IDENTIFICATION

The label on the drum cartridge shows the date of production.

B–

–

–
3 Serial number
(00001~99999)
(5 digits)

Production month
(6 digits)

1

2 Indicates production in China.

The end digit of
production year


The label on the drum cartridge shows the date of production.

1

Ver. A

Serial number (for each
month) (00001-99999)
Factory

No.
1
2
3

January

1
~

Division
Ex production
Option
Same pack

Production
month
~

The end digit
of production year

September
October
November
December

9
0
X
Y

AL-1611/AL-1622

CONSUMABLE PARTS

3–2

[ 4 ] EXTERNAL VIEWS AND INTERNAL STRUCTURE
1. APPEARANCE

3

1

2

9
11
6

3

10
12

7

13

4
5

14
8

[The figure above is an example of the AL-1622.]
1

Document feeder cover (AL-1622)
Platen cover (AL-1611)

4

Power switch

5

Operation panel

6

Paper output tray

7

Front cover

8

Paper trays

9

Side cover

10

Side cover handle

11

Bypass tray guides

12 Bypass tray

13

Bypass tray extension

14

Charger cleaner

2

Original table

3

Handles

* The AR-162/163 are equipped with one paper tray.

2. INTERNAL
2

1

3

4

12
5

13
6
7

8

9
10

11

[The figure above is an example of the AL-1622.]
1

SPF area (AL-1622 only)

2

Document feeder tray (AL-1622 only)

3

Original guides (AL-1622 only)

4

Feeding roller cover (AL-1622 only)

5

Drum cartridge handle

6

Drum cartridge

7

TD cartridge lock release lever

8

TD cartridge strap

10

Roller rotating knob

11

Fusing unit release levers

13

Paper guide
AL-1611/AL-1622

EXTERNAL VIEWS AND INTERNAL STRUCTURE

4–1

9
12

TD cartridge
Right side cover (AL-1622 only)

3. OPERATION SECTION
1

2

15 16 17

18

3

4

19 20 21

5

22

6

7

23

8 9 10 11 12

24 25

13 14

26 27

28

Not used

1

Interrupt (

) key and indicator

4

Copy ratio display(

7

Audit clear (ACC.#C)key

10

Power save (

13

B/W reverse (

16

Light (
cators

19

Clear (

22

%

) key

) indicator

2

Copy quantity display

3

Zoom indicator

5

Zoom keys

6

Paper size enter (

8

Paper size indicators

9

Alarm indicators *1

) key

11

SPF indicator (AL-1622 only)

12 Output tray full indicator

14

XY-Zoom (

15 AUTO/MANUAL/PHOTO (
) key and indicatiors

17

Numeric keys

18 Zero key

20

Start (

21 Clear all (

Preset Ratio selector keys and indicators

23

Original size enter (
indicatiors

25

Tray select (

26

Auto image (

28

Dual page copy (
cator

) key and indicator

) and dark (

) keys and indi-

) key

) key

) key and indicator

) key and indicator

/

) key

) key and 24 Auto paper select (
(AL-1622 only)
) key and indicator

/

) indicator

27 paper feed location/misfeed location indicators

) key and indi-

* 1:


ON:

TD cartridge replacement required indicator
The TD cartridge replacement required indicator will light up when
toner is needed. If copying is continued while the indicator is lit,
copies will gradually become lighter until the copier stops and the
indicator begins blinking. Replace the old TD cartridge by following
the procedure given below.
After the copier stops, it may be possible to make a few more copies by taking the TD cartridge out of the copier, shaking it horizontally, then reinstalling it. If copying is not possible after this
operation, replace the TD cartridge. During long copy run of a dark
original, the START key indicator may blink, the indicator light up,
and the copier stop, even though toner is left. The copier will feed
toner for up to 2 minutes and then the START key indicator will
light up. Press the START key to restart copying.
For best copying results, be sure to use only SHARP Genuine
Supplies which are designed, engineered and tested to maximize
the life and performance of SHARP copiers. Look for the Genuine
Supplies label on the toner package.
In case of low coverage, the developer life lamp lights up at 14,500
sheets, and flashes at 15,000 sheets and the machine stops.

Indicates that the machine is in the energy saving (pre-heat)
mode.

Blink: Indicates that the machine is in the process of resetting from the
energy saving mode or just after supplying the power.
OFF: Indicates that resetting from the energy saving mode is completed and that the fusing temperature is in ready state.
The combinations of the above display lamps are as follows:
(F = ON. D = OFF)
Lamp

Immediately
after power ON

Ready

Copying

Pre-heat lamp

Blink

D

D

Ready lamp

D

F

D

Other lamps

D

F

F

Lamp

Drum replacement required indicator The useful life of the drum
cartridge is approximately 30,000 copies. When the internal
counter reaches approximately 29,000 copies, the drum replacement required indicator will light up indicating that replacement of
the drum cartridge will be needed soon. When the indicator begins
to blink, replace the drum cartridge by following the procedure
given below.

Energy
Energy
saving mode saving
(Pre-heating) mode
(Auto power
shut off)

F

F

Blink

Blink

Ready lamp

F

D

F

D

Other lamps

F

D

F

F

Misfeed indicator
EXTERNAL VIEWS AND INTERNAL STRUCTURE

4–2

Copy is
started
during
resetting
from energy
saving mode

Pre-heat lamp

Paper required indicator

AL-1611/AL-1622

Resetting
from energy
saving
mode

4. MOTOR, SOLENOID, CLUTCH
2

3

1

4
5
6
7
8
9

11

10

12
18

14

17

15

16
No.

Name

13

Code
VFM

Function, operation

1

Exhaust fan motor

2

Toner motor

TM

3

Mirror motor

MRM

4

Cooling fan motor

CFM

Cools the inside of the machine.

5

Main motor

MM

Drives the machine.

6

Paper feed solenoid

CPFS1

Solenoid for paper feed from cassette

7

Resist roller solenoid

RRS

Resist roller rotation control solenoid

8

Manual paper feed clutch

MPFC

Drives the manual paper feed roller.

9

Manual paper feed solenoid

MPFS

Manual paper feed solenoid

10

Manual paper transport clutch

MPTC

Drives the manual paper transport roller.

11

2nd tray transport clutch

CPFC2

Drives the 2nd tray transport roller. (Excluding AL-1611)

12

2nd tray transport solenoid

FSOL2

2nd tray transport solenoid (Excluding AL-1611)

13

1st tray transport solenoid

FSOL1

1st tray transport solenoid

14

2nd tray paper feed solenoid

PSOL2

2nd tray transport solenoid (Excluding AL-1611)

15

Paper feed clutch

CPFC2

Drives the cassette paper feed roller.

16

1st tray paper feed solenoid

PSOL1

1st tray transport solenoid

17

1st tray paper feed clutch

CPFC1

Drives the 1st tray transport roller.

18

PS clutch

RRC

AL-1611/AL-1622

Cools the inside of the machine.
Toner supply
Drives the optical mirror base (scanner unit).

Drives the resist roller

EXTERNAL VIEWS AND INTERNAL STRUCTURE

4–3

5. SENSOR, SWITCH
1 2

3

4

5

6
7
8
9
10
11
24

19

17

16

15

14

13

12

18
No.

Name

Code
MHPS

Function, operation

1

Mirror home position sensor

2

1st tray detection switch

Detects the mirror (scanner unit) home position.

3

Toner density sensor

4

Paper exit sensor (paper exit side)

POD1

Detects paper exit.

5

Right door switch

DSWR

Side door open/close detection

6

Paper exit sensor (DUP side)

PDPX

Paper transport detection

7

Thermistor

8

Thermostat

1st tray detection
TCS

RTH

Toner quantity detection

Fusing section temperature detection
Fusing section abnormally high temperature detection

10

Paper in

11

2nd tray detection switch

PIN

Paper transport detection

12

Manual sensor

MPED

Manual transport detection

13

2nd tray door open/close sensor

DRS2

2nd tray door open/close detection (Excluding AL-1611)

14

2nd tray paper entry sensor

PPD2

Paper transport detection (Excluding AL-1611)

15

2nd tray paper empty sensor

CSS2

2nd tray paper empty detection (Excluding AL-1611)

16

Front door detection switch

17

1st tray paper empty sensor

CSS1

1st tray paper empty detection

18

Power switch

2nd tray detection (Excluding AL-1611)

MAIN SW

AL-1611/AL-1622

Turns ON/OFF the main power source.

EXTERNAL VIEWS AND INTERNAL STRUCTURE

4–4

6. PWB UNIT
1

2

3

4

5

8
6

7

No.

Name

Function, operation

1

Copy lamp Inverter PWB

Copy lamp control

2

Power PWB

AC power input/DC power control

3

High voltage PWB

High voltage control

4

CCD sensor PWB

Image scanning

5

Main PWB (MCU)

Machine control/Image process

6

Tray interface PWB

Paper tray control

7

ERDH operation PWB

Operation panel input and display

8

Copy operation PWB

Operation panel input and display, operation panel section control

AL-1611/AL-1622

EXTERNAL VIEWS AND INTERNAL STRUCTURE

4–5

7. SPF UNIT 
14
13
12
10
9

6
7
15

2

5

4

3

1

[Sensors and detectors]
No.

Code

Name

Type

Function, operation

1

W0

Document set sensor

Photo transmission

Document presence detection

2

COVER

Open/close sensor

Photo transmission

Paper feed unit open/close detection

3

W1

Document sensor (A4R, LTR, A5)

Photo transmission

Tray document width detection

4

W2

Document width sensor (B4R, B5)

Photo transmission

Tray document width detection

5

W3

Document width sensor (WLTR, A5R, A4, LT)

Photo transmission

Tray document width detection

6

PSOL

Pickup solenoid

7

PAPER

Paper entry sensor

9

CLH

Transport clutch

10

MOT

SPF motor

12

—

—
Photo transmission

—
Document presence detection

—
Stepping motor

Interface PWB

—

—
Tray paper feed, transport, paper exit roller drive
SPF control and communication with the copier body

13

L1

Document length detection SW (Short)

Photo transmission

Tray document length detection

14

L2

Document length detection SW (Long)

Photo transmission

Tray document length detection

15

COVER OPEN

Book sensor

Photo transmission

Detects SPF floating.

8. PAPER FEED SECTION 
5
7

3,4

2

1

6

8

9
No.

10 11 12 13

Name

Operation

1

Document length sensor (L2)

Detects the document length on the tray.

2

Document length sensor (L1)

Detects the document length on the tray.

3

Document length sensor (W0)

Detects the presence of document.

4

Document width sensor (W1, W2, W3)

Detects the document width.

5

Pickup roller

Picks up the document.

6

Paper feed roller

Feed and transport the document.

7

Paper entry sensor (PAPER)

Detects the document transport.

8

PS roller

Makes synchronization between the document lead edge and the image lead edge.

9

PS follower roller

Makes synchronization between the document lead edge and the image lead edge.

10

Transport roller

Transports the document.

11

Transport follower roller

Transports the document.

12

Paper exit follower roller

Discharges the document.

13

Paper exit roller

Discharges the document.
AL-1611/AL-1622

EXTERNAL VIEWS AND INTERNAL STRUCTURE

4–6

9. CROSS SECTIONAL VIEW
1

2

3

4

5

6
20
7
8
9
10
11
12

13
19
No.

18

17

16

15

Name

14

Function/Operation

1

Copy lamp

Image radiation lamp

2

Copy lamp unit

Operates in synchronization with No. 2/3 mirror unit to radiate documents
sequentially.

3

LSU unit

Converts image signals into laser beams to write on the drum.

4

Lens unit

Reads images with the lens and the CCD.

5

MC holder unit

Supplies negative charges evenly on the drum.

6

Paper exit roller

Used to discharge paper.

7

Upper heat roller

Fuses toner on paper (with the teflon roller).

8

Lower heat roller

Fuses toner on paper (with the silicon rubber roller).

9

Waste toner transport roller

Transports waste toner to the waste toner box.

10

Drum unit

Forms images.

11

Transfer charger unit

Transfer images (on the drum) onto paper.

12

Resist roller

Takes synchronization between the paper lead edge and the image lead edge.

13

Manual paper feed tray

Manual paper feed tray

14

Manual paper feed roller

Picks up paper in manual paper feed.

15

Manual transport roller

Transports paper from the manual paper feed port.

16

2nd tray paper transport roller

Transports paper from the 2nd tray. (Excluding AL-1611)

17

2nd tray paper feed roller (semi-circular roller)

Picks up paper from the 2nd tray. (Excluding AL-1611)

18

1st tray paper feed roller (semi-circular roller)

Picks up paper from the 1st tray.

19

MG roller

Puts toner on the OPC drum.

20

No. 2/3 mirror unit

Reflects the images from the copy lamp unit to the lens unit.

AL-1611/AL-1622

EXTERNAL VIEWS AND INTERNAL STRUCTURE

4–7

[ 5 ] UNPACKING AND INSTALLATION
1. CHECKING PACKED COMPONENTS AND
ACCESSORIES

3. INSTALLING PROCEDURE
1) Remove all pieces of tape. Then open the original cover and
remove the protective material.

Open the carton and check to ensure that the following componets and
accessories are included.

2) Use a coin (or suitable object) to remove the screw.
• Store the screw in the paper tray because it will be used if the copier
has to be moved. (Refer to the description in the following.)

TD cartridge

Operation
manual
Power cord
Copier

Drum cartridge
(installed in copier)

3) Ensure that the bypass tray is open. Raise the side coverrelease
handle and pull out the side cover until it stops.

Note:
• If anything is not included or is damaged, contact your authorised
service representative.
• Save the carton and packing materials. These can be re-used for
transporting the machine, should it be necessary.
4) Push gently on both sides of the front cover to open the cover.

2. UNPAKING PROCEDURE
Be sure to hold the handles on both sides of the copier by two persons
to unpack the copier and carry it to the installation location.

AL-1611/AL-1622

UNPACKING AND INSTALLATION

5–1

5) Gently pull the TD cartridge out while holding the handle.

9) Gently insert the TD cartridge along the guides until it locks in place.

6) Hold the strap on the cartridge and remove the TD cartridge
upward.

• If dirt or dust is adhered to the TD cartridge, remove it before installing the cartridge.

TD cartridge lock
release lever

10) Close the front cover by holding both sides with your hands and
then close the side cover. The TD cartridge replacement required
indicator will go out and the START key indicator will light up.

7) Remove the new TD cartridge from the bag. Hold the cartridge on
both sides and shake it horizontally four or five times.

• When closing the covers, be sure to close the front cover securely
and then close the side cover. If the covers are closed in the wrong
order, the covers may be damaged.

4 or 5 times

8) Remove the protective cover from the TD cartridge by unlatching
three cover hooks from the holes on the cartridge and then pulling
the cover in the direction indicated by the arrow in the illustration.

11) Raise the handle of the paper tray and pull the paper tray out until it
stops.

12) Remove the pressure plate lock. Rotate the pressure plate lock in
the direction of the arrow to remove it while pressing down the pressure plate of the paper tray.

AL-1611/AL-1622

UNPACKING AND INSTALLATION

5–2

17) Load copy paper into the tray.

13) Store the pressure plate lock which has been removed in step 5 and
the screw which has been removed in step 2 in the front of the
paper tray.

• Set the paper along the guides.
• The tray holds up to 250 sheets of about 9kg bond paper.Do not load
paper above the maximum height line.

• To store the pressure plate lock, rotate the lock to fix it on the relevant
location.
• For AL-1622, follow steps 3), 4), 13) for both the upper and lower
trays except for storage of the screw.

Maximum height line

Pressure
plate lock

18) Push the paper tray firmly back into the copier.
19) Ensure that the power switch of the copier is in the OFF position.
Insert the supplied power cord into the power cord socket at the
rear of the copier.
• If you use the copier in a country other than the country where the
copier was purchased, you will need to make sure that your local
power supply is compatible with your model. If you plug the copier
into an incompatible power supply, irreparable damage to the copier
will result.

Screw

20) Plug the other end of the power cord into the nearest outlet.
• Only insert the power cord into a properly grounded wall socket.
Do not use extension cords or power strips.

4. CHANGING THE COPY PAPER SIZE IN
THE TRAY

14) Push the pressure plate down until it locks in place.
15) Squeeze the lock lever of the front guide and slide the front guide to
match the width of the paper.

1) Gently lift and pull out the paper tray until it stops.
2) Push the pressure plate down until it locks in place.

16) Move the left guide to the appropriate slot as marked on the tray.

3) Squeeze the lock lever of the front guide and slide the front guide to
match the width of the paper.

• When using A3 copy paper, store the left guide in the slot at the left
front of the paper tray.

Left guide

Left guide

Front guide
Front guide

AL-1611/AL-1622

UNPACKING AND INSTALLATION

5–3

• Each time the ORIGINAL SIZE ENTER (
) key is pressed,
a paper size will be indicated with a paper size indicator.

4) Move the left guide to the appropriate slot as marked on the tray.
• When using 11”×17” copy paper, store the left guide in the slot at the
left front of the paper tray.

11) Press the START (
(
) key.

5) Load copy paper into the tray.
6) Place the paper size plate in the front of the paper tray.

• AL-1622 only To change the paper size setting of the other tray,
repeat steps 9 to 10 after pressing the START (
) key.

• The paper size indication which shows through the slot on the front of
the copier should match the selected paper size.
7) Push the paper tray firmly back into the copier.
8) To set the selected paper size, press the PAPER SIZE ENTER
(
) key.
• The selected paper feed location indicator will blink and the corresponding paper size (which is currently set) indicator will light up
steadily. All other indicators except the START (
) key indicator
will go out.

Note: If copying is being performed, paper size setting cannot be made.
9) AL-1622 only Use the TRAY SELECT (
) key to select the paper
tray of which the paper size has been changed.
• Each time the TRAY SELECT (
) key is pressed, a paper tray will
be indicated with a blinking paper feed location indicator.

10) Use the ORIGINAL SIZE ENTER (
paper size which is set in the paper tray.

) key to select the

AL-1611/AL-1622

) key and then the PAPER SIZE ENTER

UNPACKING AND INSTALLATION

5–4

[ 6 ] OPERATIONAL DESCRIPTIONS
1. OUTLINE OF OPERATION

F. Printing: Process section

The outline of operation is described referring to the basic configuration.

• Electrostatic latent images are formed on the OPC drum according to
the laser beams, and the latent images are developed to be visible
images (toner images).

(Basic configuration)

• Meanwhile the paper is fed to the image transfer section in synchronization with the image lead edge.

Scanner section
CCD

Operation
section

• The toner image is transferred on the paper.

G. Fusing: Fusing section
• Heat and a pressure are applied to the toner image on the copy paper
to fuse the image on the paper.

MCU (Main control/image process section)

2. SCANNER SECTION

LSU (Laser unit)
Laser diode, Polygon mirror lens
Laser beam

A. Scan process
Paper exit

The scanner has sensors that are arranged in a line. These sensors
scan a certain area of a document at a time and deliver outputs sequentially. When the line is finished, the next line is scanned, and this procedure is repeated. The figure below shows the case where an image
which is scanned is shown with solid lines.

Fusing
section

Process section
Printer section

Paper t
ransport
section
Cassette paper
feed section

The direction of this line is called main scanning direction, and the scanning direction sub scanning direction. In the figure above, one line is
divided into 5 sections. Actually, however, one line is divided into thousands of sections. For scanning, the light receiving element called CCD
is used.

Manual paper
feed section

Outline of copy operation

Sub scanning direction
Sensor scanning area

A. Setting conditions: Operation panel
Main
scanning
direction

• Set copy conditions such as the copy quantity and the copy density
with the operation section, and press the START key. The information on copy conditions is sent to the MCU.

B. Image scanning: Scanner section
• When the START key is pressed, the scanner section starts scanning
of images. The light from the copy lamp is reflected by the document
and passed through the lens to the CCD.
1

C. Photo signal/Electric signal conversion:
Scanner section

2
3

• The image is converted into electrical signals by the CCD circuit and
passed to the MCU.

4
5

D. Image process: MCU
• The document image signal sent from the CCD circuit is processed
under the revised conditions and sent to the LSU (laser unit) as print
data.

5

4

3

2

1

To MCU PWB

E. Electric signal/Photo signal
(laser beam) conversion: LSU

The basic resolution indicates the scanner capacity. The basic resolution is expressed in dpi (dot/inch) which shows the number of light emitting elements per inch on the document.
The basic resolution of this machine is 400dpi.
In the sub scanning direction, at the same time, the motor that drives
the optical system is controlled to scan the image at the basic resolution.

• The LSU emits laser beams according to the print data. (Electrical
signals are converted into photo signals.)
• The laser beams are radiated through the polygon mirror and various
lenses to the OPC drum.
AL-1611/AL-1622

OPERATIONAL DESCRIPTIONS

6–1

B. Basic structure of scanner section

1

Copy lamp (Xenon lamp)

Generate photo energy to scan documents.

2

Reflector (Converging plate)

Collects light emitted from the copy lamp and radiate the document.

3

No. 1 mirror

Refracts the reflection light from the document to No. 2 mirror.

4

No. 2 mirror

Refracts the reflection light from No. 1 mirror.

5

No. 3 mirror

Refracts the reflection light from No. 2 mirror.

6

Lens

Converges reflected light from the document to form images on the CCD element.

7

No. 2/3 mirror unit

Includes No. 2/3 mirror. Driven in synchronization with the copy lamp unit.

8

Copy lamp unit

Includes the copy lamp, the reflector, and No. 1 mirror. Driven in synchronization with No. 2/3
mirror unit by the mirror motor.

9

CCD PWB

Reflected light (image) formed on the CCD is converted into electrical signals (analog signals)
then into digital signals and sent to the MCU.

10

Mirror motor

Drives the copy lamp unit and No. 2/3 mirror unit according to the scanning speed.

11

MHPS (Mirror home position sensor)

Detects the home position of No. 2/3 mirror unit.

12

Reference white plate

Reference white sheet for scanning documents. The reference line of magnification ratio
adjustment during SIM is also drawn.

13

OC glass

Glass table to put a document on it.

The light from the light source (Xenon lamp) is reflected by a document and passed through three mirrors and reduction lenses to the CCD element
(image sensor) where images are formed. This system is known as the reduction image sensor system. Photo energy on the CCD element is converted into electrical signals (analog signals). (Photo-electric conversion). The output signals (analog signals) are converted into digital signals (A/D
conversion) and passed to the MCU (main control/image process section). The resolution at that time is 400dpi. The mirror unit in the scanner section
is driven by the mirror motor. The MHPS is provided to detect the home position of the copy lamp unit.

3. PROCESS SECTION
A. Basic structure

AL-1611/AL-1622

1

Main charger unit

2

Cleaning blade

Collects waste toner on the OPC drum.

3

OPC drum

Images are formed by laser beams electrically, and toner is attached to the image.

4

Transfer unit

Toner on the OPC drum is transferred to the
print paper by the potential difference.

5

Resist roller

Makes synchronization between the paper
and the print image.

6

MG roller

Magnetic brush is formed by developer to
put toner on the OPC drum.

7

(Laser beam)

Forms images on the OPC drum.

OPERATIONAL DESCRIPTIONS

6–2

Charges the OPC drum.

Operation cycle

Paper exit roller

Heat roller

Paper exit

Fusing
Separation

Separation charger

High voltage power

Cleaning blade

Cleaning

Waste toner box

High voltage power

Main charger

Laser scanning unit

Laser beam

Transfer

Transfer

Charging

Exposure

Developing

Synchronization
with drum

Transfer charger

High voltage power

Resist roller

Developer
High voltage
power

Developing unit

Manual paper
feed

Toner

Toner hopper

Cassette paper
feed

B. Outline of print process

C. Actual print process

The printer section of this machine employs the laser print system
where print images are formed by the laser beams on the OPC drum.

(1) Charging
A high voltage is applied to the main charger, and negative charges are
discharged to the OPC drum. A screen grid is provided between the
main charger and the OPC drum, and negative charges are uniformly
charged on the OPC drum surface.

A high voltage (corona) is applied from the main charger to the OPC
drum to charge the OPC drum.
Laser beams are radiated to the charged OPC drum to form electrical
images on the OPC drum. (Exposure)

Positive charges are attracted by the negative electrode on the OPC
drum surface and excited in the aluminum layer in the OPC drum.

(At that time, the print image on the OPC drum cannot be seen: latent
electrostatic image)
By the potential difference between the unexposed area and the latent
electrostatic images, toner ia attracted only to the images. (Developing)
(At that time, the print image formed by toner on the OPC drum can be
seen. Visible images)

DC5.5KV

The toner image on the OPC drum is transferred on the print paper by
the transfer corona (voltage).

(-525V/-400V)

After that, the print paper with the toner image on it is subject to heat
and pressure in the fusing section to fuse the image on the paper.
This machine employs the following organic photoconductor (OPC)
drum.
An OPC drum is used for the photoconductor.
(Structure of the OPC drum layers)

OPC layer
(20microns thick)
Pigment layer (0.2
to 0.3 microns thick)
Aluminium drum

AL-1611/AL-1622

OPERATIONAL DESCRIPTIONS

6–3

(2) Exposure
Non-image area

A Laser beam is generated from the semiconductor laser and controlled
by the print pattern signal. The laser writes onto the OPC drum surface
through the polygon mirrors and lens. The resistance of the OPC layer
decreases for an area exposed by the laser beam (corresponding to the
print pattern signal). The beam neutralizes the negative charge. An
electrostatic latent image is formed on the drum surface.

-600

Drum surface potential

Semiconductor laser

-400
Developing bias

Toner attract
potential

Image area
Residual potential (-50 to -100V)
0

Charge

Exposure

Developing

Transfer
Discharge

Charge

Time

Toner is attracted over the shadowed area because of the developing
bias.

(4) Transfer

Exposure
(semiconductor laser)

The visible image on the drum surface is transferred onto the print
paper by applying a positive charge from the transfer corona to the
backside of the print paper.

OPC layer
Pigment
layer
Aluminum
layer

Drum surface charge
sfter the exposure

Non-image area

Image area

OPC layer
Pigment
layer
Aluminum
layer

(3) Developing (DC bias)
A bias potential is applied to the MG roller in the two component magnetic brush developing method, and the toner is charged negative
through friction with the carrier. Non-image area of the drum surface
charged with negative potential repel the toner, whereas the laser
exposed portions where no negative charges exist, attract the toner. As
a result, a visible image appears on the drum surface.

(5) Separation
Since the print paper is charged positively by the transfer corona, it is
discharged by the separation corona. The separation corona is connected to ground.

: Carrier (Magnetized particle)
: Toner (Charge negative by friction)

(6) Cleaning

(N) (S) : Pemanent magnet
(provided in three locations)

Toner remaining on the drum is removed and collected by the cleaning
blade. It is transported to the waste toner collecting section in the cleaning unit by the waste toner transport roller.

N
S
N

DC
-400v

MG roller
-8V

AL-1611/AL-1622

OPERATIONAL DESCRIPTIONS

6–4

(7) Optical discharge (Semiconductor laser)

2) Developing bias (-400V) is applied when the photoconductor potential is switched from LOW to HIGH.

Before the drum rotation is stopped, the semiconductor laser is radiated
onto the drum to reduce the electrical resistance in the OPC layer and
eliminate residual charge, providing a uniform state to the drum surface
for the next page to be printed.When the electrical resistance is
reduced, positive charges on the aluminum layer are moved and neutralized with negative charges on the OPC layer.

3) Once developing bias (-400V) is applied and the photo conductor
potential rises to HIGH, toner will not be attracted to the drum.
<4> Stop
The reverse sequence takes place.
c. Retaining developing bias at an abnormal occurrence

Semiconductor laser

<1> Function
The developing bias will be lost if the power supply was removed during
print process. In this event, the drum potential slightly abates and the
carrier makes deposits on the drum because of strong static power. To
prevent this, the machine incorporates a function to retain the developing bias for a certain period and decrease the voltage gradually against
possible power loss.
<2> Basic function
a. Charge by the Scorotron charger

Normally, the developing bias voltage is retained for a certain time
before the drum comes to a complete stop if the machine should stop
before completing the normal print cycle. The developing bias can be
added before resuming the operation after an abnormal interruption.
Therefore, carrier will not make a deposit on the drum surface.

<1> Function
The Scorotron charger functions to maintain the surface potential of the
drum even at all times which. It is used to control the surface potential
regardless of the charge characteristics of the photoconductor.
<2> Basic function
A screen grid is placed between the saw tooth and the photoconductor.
A stable voltage is added to the screen grid to maintain the corona current on the photoconductor. As the photoconductor is charged by the
saw tooth from the main corona unit, the surface potential increases.
This increases the current flowing through the screen grid. When the
photoconductor potential nears the grid potential, the current turns to
flow to the grid so that the photoconductor potential can be maintained
at a stable level.

4. LASER UNIT
The image data sent from the MCU (image process circuit) is sent to the
LSU (laser unit), where it is converted into laser beams.

A. Basic structure
The LSU unit is the writing section of the digital optical system.The
semiconductor laser is used as the light source, and images are formed
on the OPC drum by the polygon mirror and fq lens, etc.

b. Process controlling
<1> Function

The laser beams are passed through the collimator lens, the cylindrical
lens, the polygon mirror, the fq lens, and the mirror to form images on
the OPC drum in the main scanning direction. The laser emitting PWB
is provided with the APC (auto power control) in order to eliminate fluctuations in the laser power. The BD PWB works for measurement of the
laser writing start point.

The print pattern signal is converted into an invisible image by the semiconductor laser using negative to positive (reversible) developing
method. Therefore, if the developing bias is added before the drum is
charged, toner is attracted onto the drum. If the developing bias is not
added when the drum is charged, the carrier is attracted to the drum
because of the strong electrostatic force of the drum.
To avoid this, the process is controlled by adjusting the drum potential
and the grid potential of the Scorotron charger.

2
3

1

<2> Basic function
5

Voltage added to the screen grid can be selected, high and low.To
make it easily understood, the figure below shows voltage transition at
the developer unit.
START

4
6

STOP

0

Print potentioal

Toner attract
potential

Developing bias

2)

3)
1)

Low

4)

Drum potential

High
Time

1

Semiconductor laser

Generates laser beams

2

Collimator lens

Converges laser beams in parallel

3

Polygon mirror,
polygon motor

Reflects laser beams at a constant rpm

4

BD (Mirror, lens, PWB) Detects start timing of laser scanning

5

fθ lens

Converges laser beams at a spot on
the drum.
Makes the laser scanning speeds at
both ends of the drum same as each
other. (Refer to the figure below.)

6

Laser emitting PWB

Emits laser beams according to the
image data.

<3> Start
1) Because the grid potential is at a low level, the drum potential is at
about -400V. (Carrier may not be attracted though the carrier is
pulled towards the drum by the electrostatic force of -400V.)
AL-1611/AL-1622

OPERATIONAL DESCRIPTIONS

6–5

B. Laser beam path

Makes the laser scanning speeds at both ends of the drum same as
each other.

a≠b≠c

d= e=f

a

d e

b

c

f

5. PAPER FEED SECTION
A. Basic structure

1

No. 1 cassette paper feed roller (Semi-circular roller)

Picks up paper from No. 1 cassette.

2

Main motor

Drives the process section and the paper transport section.

3

No. 1 cassette paper feed solenoid

Rotates and controls No. 1 cassette paper feed roller.

4

No. 1 cassette paper feed roller clutch

Drives No. 1 cassette paper feed roller.

5

Manual paper feed roller

Picks up paper from the manual paper feed tray.

6

Manual paper transport roller

Transport paper which was picked up from the manual paper feed tray.

7

Manual paper feed roller clutch

Drives the manual paper feed roller.

8

Manual paper transport roller clutch

Drives the manual paper transport roller.

9

Manual paper feed roller solenoid

Rotates and controls the manual paper feed roller.

10

Manual paper transport roller solenoid

Rotates and controls the manual paper transport roller.

11

Resist roller

Takes synchronization between the paper lead edge and the image lead edge.

12

Resist roller clutch

Drives the resist roller.

13

Resist roller solenoid

Rotates and controls the resist roller.
AL-1611/AL-1622

OPERATIONAL DESCRIPTIONS

6–6

(Top view)

B. Brief descriptions of operations

2

This machine allows two ways of paper feed system: cassette paper
feed and manual paper feed.
The cassette of universal type is employed to hold 250 sheets. The
front loading system allows to attach or detach the cassette from the
front of the machine.
Paper size can be selected by the user.
Since this model is not equipped with the automatic paper select function, paper size detection is not performed.

8

(1) Cassette paper feed operation
Select the cassette and press the START button, and the paper feed
roller solenoid will be turned on and the paper feed clutch will be
released.
The drive power of the main motor is transmitted through the paper feed
roller clutch to the paper feed roller, rotating the paper feed roller and
feeding paper.

(3) Resist roller
In order to make synchronization between the paper lead edge fed from
the paper feed port and the image lead edge, the roller is kept stationary for a certain time after the paper reaches at the roller towarp the
paper a little.
When the paper is warped to a certain level, the resist roller solenoid is
turned on to release the resist roller clutch.
The drive power of the main motor is transmitted through the resist
roller clutch to the resist roller, rotating the resist roller and feeding
paper.

7

5

1

Before-fusing
paper guide

Guides the paper transported from the process
section to the fusing unit.

2

Upper heat
roller

Applies heat and pressure to the paper to fuse.

3

Thermistor

Detects the surface temperature of the upper
heat roller.

4

Thermostat

Stops power supply to the heat roller in case of
an abnormally high temperature of the heat
roller.

5

Separation
pawl

Separates the print paper from the upper heat
roller.

6

POD1

Detects that the paper has been transported
from the fusing section.

(2) Manual paper feed tray operation
Select the manual paper feed tray and press the START button, and the
manual paper feed roller will be turned on to bring the paper feed roller
in contact with paper and lift the shutter simultaneously.
The drive power of the main motor is transmitted through the manual
paper feed roller clutch to the manual paper feed roller, rotating the
manual paper feed roller and feeding paper.

4

3

7

Heater lamp

Heats the heat roller.

8

Lower heat
roller

Applies a pressure to the paper together with
the upper heat roller.

B. Heat roller
A pressure roller is used for the heat roller and a silicone rubber roller is
used for the lower heat roller for better toner fusing performance and
paper separation.

C. Separator pawl
Four separator pawls are used on the upper heat roller. The separator
pawls are teflon coated to reduce friction with the roller and prevent a
smear on the paper caused by the separator pawl.

6. FUSING SECTION

D. Thermal control
1) The heater lamp, thermistor, main PWB, DC power supply PWB,
and triac within the power supply unit are used to control the temperature in the fuser unit. To prevent against abnormally high temperature in the fuser unit, a thermostat is used for safety purposes.

A. Basic composition

6

5

7
Heated by the
heater lamp.
(950W )
Safety device
(thermal breaker, thermal
fuse)

4
3
2
1

Triac (in the
power supply unit)

8

The surface temperature
of the upper heat roller
is sensed by the thermistor.

Level of the thermistor is
controlled by the main PWB.

With the signal from the
main PWB, the triac is
controlled on and off.
(power supply PWB )

2) The surface temperature of the upper heat roller is set to 180°C ~
195°C. The surface temperature during the power save mode is set
to 100°C.
AL-1611/AL-1622

OPERATIONAL DESCRIPTIONS

6–7

B. Document size detection

3) The self-check function comes active when one of the following
malfunctions occurs, and an "H" is displayed on the copy quantity
display.

Document size detection by document set tray
When a document is set on the document set tray in the auto mode of
paper/copy magnification ratio selection, the document size is detected
to perform the auto selection function of paper and the copy magnification ratio according to the detected document size.

Fusing temperature error value
H4 (Low temperature error)
• During machine operation
The case where the fusing temperature (thermistor output value)
does not reach 155°C within 55 sec from lighting of the heater
lamp. (If the toner motor rotates for 10 sec or more continuously
when starting the machine, the case where the fusing temperature does not reach 155°C within 60 sec.)

When documents of different sizes are mixed and set on the tray, the
max. size is detected. The document width is detected by the document
width sensors (W1, W2, W3), and the document length is detected by
the document length sensors (L1, L2) to determine the document size.
The document size judgment is made after a certain time from when the
document set sensor (W0) detects the document.

• During printing
When the fusing temperature (thermistor output value) falls below
145°C.
H3 (High temperature error)

L2

Fusing temperature (thermistor output value) of about 220 to 240°C
(varies depending on the resistance.)

L1

E. Fusing resistor
(1) Fusing resistor

W0

Since the upper heat roller is conductive when copy paper is highly
moistured and the distance between the transfer unit and the fusing unit
is short, the transfer current leaks through the copy paper, the upper
heat roller and the discharging brush.
To prevent against this, a resistor of 150MOhm is provided between the
frame and the discharge brush to minimize leak current and improve
transfer efficiency.

W1
W2
W3

Document size
and set direction

7. SPF SECTION 

AB series

A. Brief descriptions of operations
1) Document set (Document set sensor ON)
2) Document size detection (The document width is detected
with document width sensors W1, W2, and W3, and the
document length is detected with document length sensors
L1 and L2.)
3) Copy start (Machine)
4) SPF motor ON

Inch series

5) Pickup solenoid ON
6) Pickup roller rotation
7) Paper feed roller rotation
8) Paper entry sensor detects paper presence.

W3

L1

L2

F

D

D

D

D

F

F

D

D

D

A5R

D

D

D

D

D

A4

F

F

F

D

D

B5R

D

D

D

F

D

A4R

F

D

D

F

D

8.5" x 13"

F

D

D

F

F

B4

F

D

D

F

F

A3

F

F

F

F

F

8.5" x 5.5"

F

D

D

D

D

8.5" x 5.5"R

D

D

D

D

D

11" x 8.5"

F

F

F

D

D

11" x 8.5"R

F

D

D

F

D

8.5" x 13"

F

D

D

F

F

8.5" x 14"

F

D

D

F

F

11" x 17"

F

F

F

F

F

Note: Sensor ON: F OFF: D

11) Transport roller rotation
12) Paper exit roller rotation
13) Document exit
14) Next document
NO
15) SPF motor OFF

OPERATIONAL DESCRIPTIONS

6–8

W2

A5

10) Copy operation (Machine)

AL-1611/AL-1622

W1

B5

9) PS roller rotation

YES

Document width sen- D o c u m e n t
sor
length sensor

[ 7 ] ADJUSTMENTS
1. ADJUSTMENT ITEM LIST
Section
A Process section

Adjustment item

Adjustment procedure/SIM No.

(1) Developing bias voltage output adjustment
(2) Main charger voltage output adjustment

B Mechanism section (1) Image lead edge position adjustment

SIM 50-1

(2) Main scanning direction (FR direction) distortion
balance adjustment

No. 2/3 mirror base unit installing position adjustment

(3) Main scanning direction (FR direction) distortion adjustment

Rail height adjustment

(4) Sub scanning direction (scanning direction) distortion
adjustment

Winding pulley position adjustment

(5) Main scanning direction (FR direction) magnification
ratio adjustment

SIM 48-1

(6) Sub scanning direction (scanning direction)
magnification ratio adjustment

(7) Off center adjustment

Copy lamp unit installing position adjustment

a

OC mode in copying (SIM 48-2)

b

SPF mode in copying (SIM 48-5)

c

OC mode in FAX (SIM 48-6)

d

SPF mode in FAX (SIM 48-7)

a

OC mode (SIM 50-13)

b

C Image density
adjustment
D SPF section

SPF mode (SIM 50-16)

(8) OC (SPF) open/close detection position adjustment

OC (SPF) open/close detection position adjustment

(9) Document size detection sensor

SIM 41-3

(1) Copy mode

SIM 46-1

(1)

SIM 48-5

(2)

SIM 50-16

(3)

SIM 52-16

2. COPIER ADJUSTMENT
A. Process section

4) Adjust the adjustment volume VR31 so that the output voltage is
within the specified range shown below.

(1) Developing bias voltage adjustment
Note: Use a digital multi-meter with an internal resistance of 10MΩ or
more.
1) Set the digital multi-meter range to DC700V.
2) Put the test rod of the digital multi-meter on the developing bias
voltage output check pin.
3) Turn on the power.


Mode
Developing bias voltage
AL-1611/AL-1622

ADJUSTMENTS

7–1

Specification
DC-400 m 8V

VR31

(2) Grid bias voltage adjustment

2) Make a copy.

Note: Use a digital multi-meter with an internal resistance of 10MΩ or
more.

3) Check the copy output. If necessary, perform the following adjustment procedures.

1) Set the digital multi-meter range to DC700V.

4) Execute SIM 50-1.

2) Put the test rod of the digital multi-meter on the grid bias voltage
output check pin.

5) Set the OC lead edge position set value (Exposure display 
ON) to “99.”
The OC image scanning start position is shifted inside the document edge.

3) Turn on the power.
4) Adjust the adjustment volumes (VR51, VR52) so that the output
voltage is within the specified range. (The voltage is outputted in the
grid bias high output mode during warming up, and in the grid bias
low output mode after completion of warming up.)

6) Set the main cassette lead edge void adjustment value (Exposure
display  ON)* to “1.”
The lead edge void becomes the minimum.
7) Set the print start position value (Exposure display  ON) to
“99” and make a copy.
The print start position is shifted inside the document edge.

5mm
5
4mm
10

*The dimension varies depending on the model.
8) Measure the image loss R of the copied image. Enter the set value
of the image scanning lead edge position (Exposure display
 ON) again.


Mode

Specification

• 1 step of the set value corresponds to about 0.127mm shift.

Grid bias LOW

DC-400 m 20V

VR52

Grid bias HIGH

DC-525 m 10V

VR51

• Calculate the set value from the formula below.
99 - R/0.127 (mm) = Image loss set value 

B. Mechanism section
(1) Image lead edge position adjustment (SIM 50-1)
a. OC image lead edge position adjustment

5mm

Note: In advance to this adjustment, the sub scanning magnification
ratio adjustment must be performed.

0mm

1) Set a scale on the OC table as shown below.

5

10

*The scanning edge is set.
(A line may be printed by scanning the document edge.)
Example: 99 - 4/0.127 = 99 - 31.5 = about 67
Note: If the set value is not obtained from the above formula, perform the fine adjustment.

AL-1611/AL-1622

ADJUSTMENTS

7–2



9) Measure the distance H between the paper lead edge and the
image print start position. Set the image print start position set value
(Exposure display  ON) again.

Adjustment
mode

• 1 step of the set value corresponds to about 0.127mm shift.

SIM

LED

OC image
lead edge
position

• Calculate the set value from the formula below.
99 - H/0.127 (mm) = Image print start position set value 

2nd tray lead
edge void

PHOTO
SIM
50-1

0mm
5

Multi bypass
traylead edge
void

10

Set
range

Spec value

99
R/0.127

AUTO

Main
cassette lead
edge void

0mm

Set value

AUTO +
MANUAL
+ PHOTO

Lead edge
void: 1 - 4mm
1 ~ 99
Image loss:
3mm or less

B/0.127

MANUAL
+ PHOTO

Print start
position

EXP1

99 –
H/0.127

b. SPF image lead edge position adjustment
1) Set a scale on the OC table as shown below.
*Fit the print edge with the paper edge, and perform the
lead edge adjustment.

Example: 99 - 5/0.127 = 99 - 39.4 = about 59
Note: If the set value is not obtained from the above formula, perform the fine adjustment.
10) Set the main cassette lead edge void adjustment value (Exposure
display  ON)* again.
• 1 step of the set value corresponds to about 0.127mm shift.
• Calculate the set value from the formula below.
B/0.127 (mm) = Lead edge void adjustment value 
Note: Since the printed copy is used as a test chart, put the scale in
paralled with the edge lines.

2.5mm
5

2) Make a copy, Then use the copy output as an original to make an
SPF copy again.
2.5mm

3) Check the copy output. If necessary, perform the following adjustment procedures.

10

4) Execute SIM 50-1.
5) Set the SPF lead edge position set value (Exposure display  ON) so that the same image is obtained as that obtained in
the previous OC image lead edge position adjustment.
Example: When setting the lead edge void to 2.5mm:
2.5 /0.127 = about 20


Adjustment
mode

Note: If the set value is not obtained from the above formula, perform the fine adjustment.

SPF image
lead edge
position

*2nd tray lead edge void adjustment: Exposure display 
Multi bypass tray lead edge void adjustment: Exposure display


AL-1611/AL-1622

ADJUSTMENTS

7–3

SIM

LED

SIM
50-1

MANUAL

Set value

Spec value

Lead edge
1 step:
void: 1 - 4mm
0.127mm
Image loss:
shift
3mm or less

Set
range

1 ~ 99

c. Rear edge void adjustment

d. Paper off center adjustment

1) Set a scale as shown in the figure below.

1) Execute SIM 50-1 and set the density mode of AUTO + MANUAL
(Left edge void) to 1.

A4(8.5" x 11")

2) Set a test chart (UKOG-0089SCZZ) on the document table.
3) Select a paper feed port and make a copy.
Compare the copy and the test chart. If necessary, perform the following adjustment procedure.
4) Execute SIM 50-10.
After completion of warmup, shading is performed and the currently
set off center adjustment value of each paper feed port is displayed.
5) Enter the set value and press the start key.
The correction value is stored and a copy is made.

Mode

SIM

LED

Set value

Specification

Paper rear edge
Paper off
center

2) Set the document size to A4 (8.5” x 11”), and make a copy at 100%.

SIM
50-10

3) If necessary, perform the following adjustment procedure.

Void amount (Standard value: 4mm or less)

Add 1:
0.127mm shift
Single:
Selected to R side.
Center
tray ON Reduce 1:
m 2.0mm
0.127mm shift
to L side.

Set
range

1 ~ 99

* When SIM 48-01 (AE) is executed, the document off-center is automatically set. Therefore, the off-center adjustment previously described in
5) must be adjusted again.

Scale image

e. Left edge void area adjustment
Note: Before performing this adjustment, be sure to check that the
paper off center adjustment (SIM 50-10) is completed.

Paper rear edge

1) Set a test chart (UKOG-0089SCZZ) on the document table.
2) Select a paper feed port and make two copies.
Compare the 2nd copy and the test chart. If necessary, perform the
following adjustment procedure.

4) Execute SIM 50-1 and set the density mode to AUTO + PHOTO
(Rear edge void).

*The 1st copy does not show the void. Be sure to check the 2nd
copy.

The currently set adjustment value is displayed.
5) Enter the set value and press the start key.

3) Execute SIM 50-1 and set the density mode to AUTO + MANUAL
(Left edge void).

The correction value is stored and a copy is made.

The currently set adjustment value is displayed.
(When the off center adjustment previously described is performed,
“0” is displayed.)

Note: Before performing the 2nd print surface rear edge void
adjustment, be sure to perform the 2nd print surface lead
edge position adjustment. Never reverse the sequence.

4) Enter the set value and press the start key.


Mode
Rear edge
void

SIM
SIM
50-1

LED
AUTO +
PHOTO

Set value Specification

The correction value is stored and a copy is made.

Set
range



1 step:
0.127mm 4mm or less 1 ~ 99
shift

Mode
Left edge void

SIM

LED

SIM
50-1

AUTO +
MANUAL

Set value Specification

Set
range

1 step:
0.127mm
shift

1 ~ 99

0.5 ~ 4mm

* When the left edge void is set with the paper off center adjusted, the
both edge void is automatically adjusted.

AL-1611/AL-1622

ADJUSTMENTS

7–4

(2) Main scanning direction
(FR directional distortion balance adjustment)

3) Manually turn the mirror base drive pulley and bring No. 2/3 mirror
base unit into contact with the positioning plate.
At that time, if the front frame side and the rear frame side of No. 2/
3 mirror base unit are brought into contact with the positioning plate
at the same time, the mirror base unit parallelism is proper.
If one of them is in contact with the positioning plate, perform the
adjustment of 4).

1) Remove the OC glass and the right cabinet.

2) Loosen the copy lamp unit wire fixing screw.

4) Loosen the set screw of the scanner drive pulley which is not in
contact with No. 2/3 mirror base unit positioning plate.
5) Without moving the scanner drive pulley shaft, manually turn the
scanner drive pulley until the positioning plate is brought into contact with No. 2/3 mirror base unit, then fix the scanner drive pulley.

AL-1611/AL-1622

ADJUSTMENTS

7–5

2) Open the original cover and make a normal (100%) copy.

6) Put No. 2/3 mirror base unit on the positioning plate again, push the
projections on the front frame side and the rear frame side of the
copy lamp unit to the corner frame, and tighten the wire fixing
screw.

3) Measure the width of the black background at the lead edge and at
the rear edge.

If the width (La) of the black background at the lead edge is equal
that (Lb) at the rear edge, there is no need to execute the following
procedures of 4) ~ 7).
4) Loosen the mirror base drive pulley fixing screw on the front frame
side or on the rear frame side.
• When La < Lb
Turn the mirror base drive pulley on the front frame side in the arrow
direction A. (Do not move the mirror base drive pulley shaft.)
• When La > Lb
Turn the mirror base drive pulley on the front frame side in the arrow
direction A. (Do not move the mirror base drive pulley shaft.)

Rear side
A

(3) Main scanning direction (FR direction) distortion
adjustment

B

This adjustment must be performed in the following cases:
• When the mirror base drive wire is replaced.

Front side

• When the lamp unit, or No. 2/3 mirror holder is replaced.
• When a copy as shown is made.
La

Lb

5) Tighten the mirror base drive pulley fixing screw.

La = Lb
1) Set A3 (11” x 17”) white paper on the original table as shown below.

6) Execute the main scanning direction (FR) distartion balance adjustment previously described in 2) again.

AL-1611/AL-1622

ADJUSTMENTS

7–6

(4) Sub scanning direction (scanning direction)
distortion adjustment

4) Move the mirror base F rail position up and down (in the arrow
direction) to adjust.

When there is no skew copy in the mirror base scanning direction and
there is no horizontal error (right angle to the scanning direction), the
adjustment can be made by adjusting the No. 2/3 mirror base unit rail
height.
Before performing this adjustment, be sure to perform the horizontal
image distortion adjustment in the laser scanner section.
This adjustment must be performed in the following cases:
• When the mirror base wire is replaced.
• When the copy lamp unit or No. 2/3 mirror unit is replaced.
• When the mirror unit rail is replaced or moved.
• When a following copy is made.

Note: If the rear side rail is used for the adjustment, the scanning position of the white balance sheet is shifted and “E7-04” may occur
only when scanning with the SPF. Therefore it is advisable to
use the front side rail for the adjustment.

1) Making of a test sheet

• When La > Lb
Shift the mirror base B rail upward by the half of the difference of La
– Lb.

Make test sheet by drawing parallel lines at 10mm from the both
ends of A3 (11” x 17”) white paper as shown below. (These lines
must be correctly parallel to each other.)

10mm

• When La < Lb
Shift the mirror base B rail downward by the half of the difference of
Lb – La.

10mm

Example: When La = 12mm and Lb = 9mm,, shift the mirror base
B rail upward by 1.5mm.
• When Lc > Ld
Shift the mirror base B rail downward by the half of the difference of
Lc – Ld.

10mm

• When Lc < Ld
Shift the mirror base B rail downward by the half of the difference of
Ld – Lc.

10mm

* When moving the mirror base rail, hold the mirror base rail with your
hand.
2) Make a normal (100%) copy of the test sheet on A3 (11” x 17”)
paper. (Fit the paper edge with the glass holding plate edge.)



3) Measure the distances (La, Lb, Lc, Ld) at the four corners as shown
below.

5) After completion of adjustment, manually turn the mirror base drive
pulley, scan the mirror base A and mirror base B fully, and check
that the mirror bases are not in contact with each other.

La

Lb

La = Lb, Lc = Ld

Lc

* If the mirror base rail is moved extremely, the mirror base may be in
contact with the frame or the original glass. Be careful to avoid this.

Ld

When La = Lb and Lc = Ld, no need to perform the procedures 4)
and 5).
AL-1611/AL-1622

ADJUSTMENTS

7–7

(5) Main scanning direction (FR direction) magnification
ratio adjustment (SIM 48-1)

(6) Sub scanning direction (scanning direction)
magnification ratio adjustment (SIM 48-2, SIM 48-5)

Note: Before performing this adjustment, be sure to check that the
CCD unit is properly installed.

a. OC mode in copying
Note: Before performing this adjustment, be sure to check that the
CCD unit is properly installed.

1) Put a scale on the original table as shown below.

1) Put a scale on the original table as shown below, and make a normal (100%) copy.
2) Compare the scale image and the actual image. If necessary, perform the following adjustment procedures.
3) Execute SIM 48-2.
4) After warmup, shading is performed and the current set value of the
sub scanning direction magnification ratio is displayed on the display section in 2 digits.
5) Enter the set value and press the start key.
The set value is stored and a copy is made.
2) Execute SIM 48-1.



3) After warmup, shading is performed and the current set value of the
main scanning direction magnification ratio is displayed on the display section in 2 digits.

Mode

Specification

Sub scanning
direction
Normal
m 1.0%
magnification
ratio (OC mode)

4) Select the mode and press the start key again.

SIM
SIM
48-2

Set value
Add 1:
0.1% increase
Reduce 1:
0.1% decrease

Set range

1 ~ 99

5) Auto correction mode (AE lamp ON)
b. RSPF sub scanning direction magnification ratio

The mirror unit moves to the shading position, and the reference
width of the reference white plate is scanned, and the correction
value is automatically calculated from that scanned value.

Note:
• Before performing this adjustment, be sure to check that the CCD
unit is properly installed.

The correction value is displayed and a copy is made.

• Before performing this adjustment, the OC mode adjustment in
copying must be completed.

6) Compare the scale image and the actual scale.
If a fine adjustment is required, switch to the manual correction
mode with the magnification ratio display key and perform fine
adjustment.

1) Put a scale on the original table as shown below, and make a normal (100%) copy to make a test chart.

7) Manual correction mode (TEXT lamp ON)
Enter the set value and press the start key.
The set value is stored and a copy is made.

Note: A judgement must be made with 200mm width, and must not be
made with 100mm width.
Mode

Specification

Main scanning
direction
At normal:
magnification m 1.0%
ratio

SIM
SIM
48-1

Set value
Add 1:
0.1% increase
Reduce 1:
0.1% decrease

Set range

1 ~ 99
Note: Since the printed copy is used as a test chart, put the scale in
parallel with the edge lines.

• Error in the auto correction mode
Display
Copy quantity
display “– –”

Paper
jam lamp ON

Content
The correction
value calculated
is over 5%.

Reference line
scanning error

2) Set the test chart on the SPF and make a normal (100%) copy.

Major cause

3) Compare the scale image and the actual image. If necessary, perform the following adjustment procedures.

• Improper position of reference
width line of the reference
white plate
• Improper installation of CCD
unit

4) Execute SIM 48-5.
5) After warmup, shading is performed.

• Defective CCD
• No reference white plate

The auto density lamp lights up and the current front surface sub
scanning direction magnification ratio correction value is displayed
in two digits on the display section.

* When SIM 48-01 (AE) is executed, the main scanning direction magnification ratio is automatically set. Therefore, the main scanning
direction magnification ratio adjustment previously described in 5)
must be made again.

6) Enter the set value and press the start key.
The set value is stored and a copy is made.

AL-1611/AL-1622

ADJUSTMENTS

7–8

b. SPF original off-center adjustment 

7) Change the mode from the duplex original mode to the simplex
original mode.

Note: Before performing this adjustment, be sure to check that the
paper off center is properly adjusted.

“MANUAL” lamp lights up and the current back surface sub scanning direction magnification ratio is displayed in two digits on the
display section.

1) Make a test chart for the center position adjustment and set it on the
SPF.

8) Enter the set value and press the start key.



The set value is stored and a copy is made.

Draw a line on a paper in the scanning direction.


Mode

Specification

Sub scanning
direction magni- Normal
fication ratio
m 1.0%
(SPF mode)

SIM
SIM
48-5

Set value

2) Make a normal copy from the manual paper feed tray, and compare
the copy and the original test chart.

Set range

Add 1:
0.1% increase
Reduce 1:
0.1% decrease

If necessary, perform the following adjustment procedures.
1 ~ 99

3) Execute SIM 50-16.
4) After warmup, shading is performed and the current set value of the
off center adjustment at each paper feed port is displayed on the
display section in 2 digits.

(7) Off center adjustment (SIM 50-13, SIM 50-16)
a. OC mode

5) Enter the set value and press the start key.

Note: The operation of SIM 50-13 is the same as that of SIM 48-01
(Photo LED ON)

The set value is stored and a copy is made.


1) Make a test chart as shown below and set it so that its center line is
fit with the original guide center mark.

Mode

*To make a test chart, draw a line on A3 or 11” x 17” paper at the
center in the paper transport direction.

Specification

Original off
center mode
(SPF mode)

SIM

Set value

Add 1:
0.1mm shift to R
SIM side
Single:
Center m 3.0mm 50-16 Reduce
1: 0.1mm shift to
L side

Set range

1 ~ 99

(8) OC (SPF) open/close detection position adjustment

1) Set A4 or 8 1/2” x 11” paper on the OC table.
Check that the document size display on the operation panel indicates the correct size of the set paper.
2) Close the OC (SPF) with a small clearance for insertion of your
hand left, and remove the paper from the OC table.
The document size display does not change from the display in 1).

2) Make a normal copy from the manual paper feed tray, and compare
the copy and the test chart.

3) Open the OC (SPF) slowly until the display on the operation panel
changes (all the document size display lamps are turned off), and
measure dimension A shown below under that state.

If necessary, perform the following adjustment procedures.
3) Execute SIM 50-13.

Distance A = Table glass top - OC (SPF) knob 117"

4) After warmup, shading is performed and the current set value of the
off center adjustment is displayed on the display section in 2 digits.
5) Enter the set value and press the start key.

Open

The set value is stored and a copy is made.

A


Mode

Specification

SIM

Set value

Add 1:
0.1mm shift to R
Original off
SIM side
Single:
center mode
Center m 2.0mm 50-13 Reduce 1:
(OC mode)
0.1mm shift to L
side

Set range

1 ~ 99

Check the position where the display checked in
procedure 1) is changed.

AL-1611/AL-1622

ADJUSTMENTS

7–9



C. Image density adjustment

OC (SPF) open/close position A: 207 ~ 302mm

(1) Copy mode (SIM 46-1)

4) If the OC (SPF) open/close position A is not 207 ~ 302mm, adjust
the open/close sensor mounting plate position as shown below.

1) Set a test chart (UKOG-0162FCZZ) on the OC table as shown
below.

Open/close sensor mounting plate
(A)

(B)

2) Put several sheets of A3 or 11” x 17” white paper on the test chart.
3) Execute SIM 46-1.
4) After warmup, shading is performed and the current set value of the
density level is displayed on the display section in 2 digits.

Factory setting : second from the top

For mode selection, use the density select key.
5) Change the set value with the 10-key to adjust the copy image density.
6) Make a copy and check that the specification below is satisfied.


AL-1611/AL-1622

Density
mode

Display
lamp

Auto

Auto

—

Manual

Manual

3

Photo

Photo

3

Toner
save

Manual/
Photo

3

ADJUSTMENTS

7 – 10

Exposure
level

Sharp Gray
Chart output

Set value

“3” is slightly The greater
copied.
the set value
is, the greater
“3” is slightly
the density is.
copied.
The smaller
“3” is slightly the set value
copied.
is the smaller
the density is.
“3” is slightly
copied.

Set
range
1 ~ 99

[ 8 ] SIMULATIONS

Main
code

1. ENTERING THE SIMULATION MODE

Sub
code

22

Contents

*

12

Drum counter display

Perform the following procedure to enter the simulation mode.
Clear key 3 Interrupt key 3 “0“ key 3 Interrupt key 3 Main code 3
Start key 3 Sub code 3 Start key

14

Copier ROM version display

15

Trouble memory display

16

Duplex print counter display

2. CANCELLING THE SIMULATION MODE

17

Copy counter display

18

Printer counter display

B

19

Electronic sort counter display

B

21

Scanner counter display

1

JAM memory, JAM counter clear

2

Trouble memory clear

4

SPF counter clear

A

5

Duplex counter clear

B

6

Paper feed counter clear

7

Drum counter clear
Copy counter clear

When the clear all key is pressed, the simulation mode is cancelled.
When the interruption key is pressed, the process is interrupted and the
screen returns to the sub code entering display.
24

* After canceling the simulation mode, be sure to turn OFF/ON the
power and check the operation.

3. LIST OF SIMULATIONS

B

Main
code

Sub
code

1

1

Mirror unit operation check

8

2

Optical system sensor operation check

9

Printer counter clear

B

1

SPF aging

A

10

Electronic sort counter clear

B

2

SPF sensor operation check

A

13

Scanner counter clear

3

SPF motor forward rotation operation check

A

1

Main motor operation check

4

SPF motor reverse rotation operation check

A

2

8

3

5

7

8

9

SPF paper feed solenoid operation check

25
26

A

10

Polygon motor operation check

1

Option switch display
Auditor setting

9

RSPF reverse solenoid operation check

B

3

10

RSPF paper exit gate solenoid operation check

B

5

Counter mode setting

11

SPF PS release solenoid operation check

A

6

Destination setting

2

Shifter job separator sensor operation check

B

7

CRUM set value display

3

Shifter operation check

B

10

Model name setting

4

Job separator operation check

B

22

Language setting

11

Shifter Home Position Check

B

30

CE mark conformity control setting

Operation panel display check

32

Fan rotation duty change state setup

Heater lamp lighting check, cooling fan motor operation check

38

Cancel of stop at dram life over

42

Transfer timing adjustment
Black-white reversion function setup

1
2

6

*

Contents

B

B

3

Copy lamp lighting check

50

1

Paper feed solenoid operation check

51

Sort/Group copy temporary stop function setup

10

Main cassette semi-circular roller drive

30

1

Machine sensor operation check

1

Aging with warmup time display

41

2

OC document sensor adjustment

B

4

Warmup saving

3

Document sensor light reception level display

B

6

Intermittent aging

42

1

Developing counter clear

B

8

Warmup time display

43

1

Fusing temperature setting

1

Developing bias voltage output check

46

1

Copy density level adjustment

2

Main charger voltage output check (Grid bias high mode)

48

1

3

Main charger voltage output check (Grid bias low mode)

Main scanning (front/rear) direction magnification ratio
adjustment (Copy/OC-SPF common)

2

OC mode sub scanning direction magnification ratio
adjustment in copying

5

SPF mode sub scanning direction magnification ratio
adjustment in copying

6

Transfer charger voltage check

1

Duplex motor forward rotation operation check

B

2

Duplex motor reverse rotation operation check

B

4

Duplex motor rotation speed adjustment

B

5

Duplex motor switchback time adjustment

B

50

1

Copy image lead edge position adjustment

10

Paper off center adjustment

B

A

10

Toner motor operation check

13

OC mode document off center adjustment

14

Trouble (except for U2) cancel

16

SPF mode document off center adjustment

A

16

U2 trouble cancel

18

Duplex memory reverse print adjustment

B

19

Duplex rear edge void adjustment

B

2

Resist amount adjustment

20

1

Maintenance counter clear

B

21

1

Maintenance cycle setting

B

51

2

Mini maintenance cycle setting

B

53

22

1

Maintenance counter display

B

2

Maintenance preset value display

B

3

JAM memory display

4

Total JAM counter display

5

Total counter display

6

Developing counter display

7

Developing preset counter value display

B

8

SPF counter display

A

9

Paper feed counter display

63

B

8

SPF scan position auto adjustment

A

9

SPF white level value display

A

1

Shading data check

7

White correction start pixel/position auto adjustment

64

1

Self printing mode

67

14

Printer Flash ROM Data Download

*A: Only AL-1622
B: Not used

AL-1611/AL-1622

SIMULATIONS

8–1

A
B

4. CONTENTS OF SIMULATIONS
Main
code

Sub
code

1

1

Contents
Mirror unit operation check

Details of operation
Used to execute scanning at the speed corresponding to the set magnification
ratio.
Key operation

Set range

100%

50 ~ 200%

100%

50 ~ 200%

Display

Changing the magnification ratio:
Fixed magnification ratio key
ZOOM UP KEY, ZOOM DOWN
KEY
2

Initial
value

Set magnification ratio:
Fixed magnification ratio LED
ZOOM LED

Optical system sensor oper- Used to check MHPS (Mirror home position sensor) ON/OFF state with the
ation check
LED on the operation panel.
Display

MHPS: Paper empty LED

2

1

SPF aging

Used to perform SPF document transport.
The paper size is not detected. (Excluding postcards, extra large sheet of 1m
or greater.)
With SPF installed: Single transport operation
With RSPF installed: Duplex transport operation
Key operation

Display

Changing the magnification ratio:
Fixed magnification ratio key
ZOOM UP KEY, ZOOM DOWN
KEY

Set magnification ratio:
Fixed magnification ratio LED
ZOOM LED


2

SPF sensor operation check Used to check sensors in SPF with the LED on the operation panel.
Display




PW1: JAM LED
PW2: Paper empty LED
PW3: Machine position JAM LED
PW4: SPF JAM LED
PL1: Manual paper feed tray select LED
PL2: 2nd tray position JAM LED
P-IN: SPF select LED
SPF COVER OPEN: Main cassette select LED

3

SPF motor forward rotation
operation check


Used to rotate the SPF motor forward for 10 sec.

4

SPF motor reverse rotation
operation check


Used to rotate the SPF motor reversely for 10 sec.

8

SPF paper feed solenoid
operation check


Used to drive the SPF paper feed solenoid (PSOL) at the cycle of 500 msec
ON and 500 msec OFF 20 times.

9

RSPF reverse solenoid
operation check


Used to drive the RSPF reverse solenoid (RSOL) at the cycle of 500 msec ON
and 500 msec OFF 20 times.

10

RSPF paper exit gate solenoid operation check


Used to drive the RSPF paper exit gate solenoid (GSOL) at the cycle of 500
msec ON and 500 msec OFF 20 times.

11

SPF PS release solenoid
operation check


Used to drive the SPF PS release solenoid at the cycle of 500 msec ON and
500 msec OFF 20 times.

AL-1611/AL-1622

SIMULATIONS

8–2

Main
code

Sub
code

3

2

Contents
Shifter job separator sensor
operation check

Details of operation

Initial
value

Set range

Used to check the sensors state in the shifter job separator with the LED on
the operation panel.
Display


3

Shifter operation check


Shifter HP sensor: Machine position JAM LED
Job separator HP sensor: SPF JAM LED
Paper exit full sensor: 2nd tray position JAM LED
Used to drive the shifter motor at the speed of printing of A4 (8-1/2 x 11”).
Pressing the clear all key or interrupt key moves the shifter to the home position.
Key operation


4

Job separator operation
check

The shifter is moved to the home position: Clear all key, interrupt key
Used to drive the job separator one way. Pressing the clear all key or interrupt
key stops the job separator at the home position.
Key operation


11

Shifter Home Position check

Stops at the home position: Clear all key, interrupt key
Used to drive the shifter motor
Key operation


5

6

Feed: Exposure up key or "3" key
Return: Exposure down key or "4" key
Move to Home Position: Magnification ratio display key or "5" key

1

Operation panel display
check

Used to light all LED’s on the operation panel for 5 sec.

2

Heater lamp lighting check,
cooling fan motor operation
check

Used to turn ON the heater lamp for 500 msec and OFF for 500 msec 5 times.
At the same time, the cooling fan is rotated at a high speed. After checking the
heater lamp operation, the cooling fan motor rotate at a low speed.

3

Copy lamp lighting check

Used to light the copy lamp for 10 sec.

1

Paper feed solenoid operation check

When the start key is pressed, the selected paper feed solenoid is driven at
the cycle of 500 msec ON and 500 msec OFF 20 times.
Key operation
Solenoid selection:
Tray select button

7

Display

Main cassette paper feed solenoid:
Main cassette select LED
Multi manual paper feed solenoid:
Manual paper feed select LED
No. 2 cassette paper feed solenoid:
No. 2 cassette select LED
Resist roller solenoid:
Machine position JAM LED
No. 2 cassette transport solenoid:
No. 2 cassette position JAM LED

10

Main cassette semi-circular
roller drive

1

Aging with warmup time dis- Execute the simulation input with the copier side cover open, then close the
play
side cover, and the machine will start warming up. Warm up time is counted
up every 2nd and it is displayed. After completion of warmup, count up is terminated. When the clear all key is pressed ready lamp is lighted and the copy
quantity is entered and the start key is pressed, copying is made to make the
set quantity of copies. At that time, the paper size does not matter.

Excute the simulation with the developer cartridge removed, used to rotate the
semi-circular roller of the main cassette one turn to face it downward.
1 ~ 99

Key operation
Copy quantity setting: Copy quantity keys
4

Warmup saving

Used to bring the machine to the ready state without warmup.

AL-1611/AL-1622

SIMULATIONS

8–3

1 ~ 99

Main
code

Sub
code

7

6

Contents
Intermittent aging

Details of operation

Initial
value

Set range
1 ~ 99

After completion of warmup, counting is stopped and the ready lamp is
lighted. When the copy quantity is entered and the start key is pressed, copying is made to make the set quantity of copies. After 3 sec standby, copying is
made again to make the set quantity of copies. After that this operation is
repeated. The paper size does not matter.
Key operation
Copy quantity setting: Copy quantity keys

8

9

8

Warmup time display

Execute the simulation input with the copier side cover open, then close the
side cover, and the machine will starts warming up. Warm up time is counted
up every 2nd and it is displayed.

1

Developing bias voltage
output check

Used to out put the developing bias for 30 sec. For the adjustment procedure
of the developing bias, refer to the previous descriptions.

2

Main charger voltage output Used to output the main charger grid bias voltage at the high mode for 30 sec.
check (Grid bias high mode) For the adjustment procedure of the main charger grid bias voltage, refer to
the previous descriptions.

3

Main charger voltage output
check (Grid bias low mode)

Used to output the main charger grid bias voltage at the low mode for 30 sec.
For the adjustment procedure of the main charger grid bias voltage, refer to
the previous descriptions.

6

Transfer charger voltage
check

Used to output the transfer charger voltage for 30 sec. For the adjustment procedure of the transfer charger voltage, refer to the previous descriptions.

1

Duplex motor forward rotation operation check


Used to rotate the duplex motor forward for 30 sec.

2

Duplex motor reverse rotation operation check


Used to rotate the duplex motor reversely for 30 sec.

4

Duplex motor rotation speed
adjustment

The currently set duplex motor rotation speed set value is displayed. When
the set value is entered and the start key is pressed, the set value is stored.

1 ~ 99

6

1 ~ 13

50

18 ~ 76

2

0~7

Key operation

5

Duplex motor switchback
time adjustment

Duplex motor rotation speed set value: Copy quantity keys
The currently set duplex motor switchback time set value is displayed. When
the set value is entered and the start key is pressed, the set value is stored.
Key operation



Duplex motor switchback time set value: Copy quantity keys

10

Toner motor operation check Used to operate the toner motor for 30 sec.
Note: If this simulation is executed with the toner hopper installed, toner is
automatically supplied to the developer. Be careful of overtoner.

14

Trouble (except for U2)
cancel

Used to cancel troubles except for U2.

16

U2 trouble cancel

Used to cancel U2 trouble.

20

1

Maintenance counter clear

Used to clear the maintenance counter. *2

21

1

Maintenance cycle setting

Used to display the currently set maintenance cycle at the numbers shown at
right. When the set value is entered and the start key is pressed, the set value
is stored.
Key operation/Display
0: 2500 sheets
1: 5000 sheets
2: 25000 sheets (When toner save is ON)
3: 50000 sheets (When toner save is ON)

*2: Display after clearing each counter 000
(0.75 sec) 3 Blank (0.35 sec) 3 000 (0.75 sec) 3 Blank (1.0 sec) 3 Repetition

AL-1611/AL-1622

SIMULATIONS

8–4

4: 150000 sheets
5: FREE (999999 sheets)
6: 10000 sheets
7: 7500 sheets

Main
code

Sub
code

21

2

Contents

Details of operation

Mini maintenance cycle setting

Used to display the currently set mini maintenance cycle at the numbers
shown at right. When the set value is entered and the start key is pressed, the
set value is stored.
Key operation/Display
4: 30000 sheets (When toner save is OFF)
50000 sheets (When toner save is ON)

0: 2500 sheets
1: 5000 sheets
2: 10000 sheets
3: FREE (999999 sheets)
22

1

Maintenance counter display Used to display the current maintenance counter value. *1

2

Maintenance preset value
display

Used to display the current maintenance preset value (set with SIM 21-1). *1

3

JAM memory display

Used to display a JAM generated during copying on the JAM position display
on the operation panel. Max. 30 recent jams are stored. JAM No. 1 is displayed even when there is no JAM.
Key operation

Display

JAM history select:
Magnification ratio display key

The history number (1 ~ 30) is
displayed on the display.
The JAM position LED corresponding to the history number is lighted.

4

Total JAM counter display

Used to display the current total JAM counter value. *1

5

Total counter display

Used to display the current total counter value. *1

6

Developing counter display

Used to display the current developing unit counter value. *1

7

Developing preset counter
value display

Used to display the current mini maintenance preset value (set with SIM 21-2). *1

8

SPF counter display


Used to display the current SPF counter value. *1

9

Paper feed counter display

Used to display the current paper feed counter value for each paper feed port. *1
Key operation
Paper feed port selection: Tray select key

12

Drum counter display

Used to display the current drum counter value. *1

14

Copier ROM version display

Used to display the version number of the main ROM.
Display
(Example) When the ROM version is 4.01:
004 3 Blank 3 001 3 Blank 3 Repetition

15

Trouble memory display

Used to display the actually occurred trouble codes on the display on the
operation panel. When the start key is pressed during the main code display,
the sub code is displayed. Max. 20 recent trouble codes are stored.
Key operation

Display

Sub code display: Start key
Trouble code history select:
Magnification ratio display key

Histories 1 ~ 10: The upper digit of
display "A" ~ "J" lights up.
Histories 11 ~ 20: The upper digit of
display "A" ~ "J" blinks.
• Display without trouble code Main
code: "– –"
Sub code: "00"

*1: Each counter display method
To display 123456: 123 (0.75 sec) 3 Blank (0.35 sec) 3 456 (0.75 sec) 3 Blank (1.0 sec) 3 repetition
*2: Display after clearing each counter
000 (0.75 sec) 3 Blank (0.35 sec) 3 000 (0.75 sec) 3 Blank (1.0 sec) 3 Repetition

AL-1611/AL-1622

SIMULATIONS

8–5

Initial
value

Set range

4

0~4

Main
code

Sub
code

22

16

Duplex print counter display


Used to display the current duplex print counter value. *1

17

Copy counter display

Used to display the current copy counter value.

18

Printer counter display


Used to display the current printer counter value. *1

19

Electronic sort counter display


Used to display the current electronic sort counter value. *1

21

Scanner counter display

Used to display the current scanner counter value.

1

JAM memory, JAM counter
clear

Used to clear the JAM memory and the JAM counter. *2

2

Trouble memory clear

Used to clear the trouble memory. *2

4

SPF counter clear


Used to clear the SPF counter.

5

Duplex counter clear


Used to clear the duplex counter. *2

6

Paper feed counter clear

Used to clear the paper feed counter. *2

7

Drum counter clear

Used to clear the drum counter. *2

8

Copy counter clear

Used to clear the copy counter. *2

9

Printer counter clear


Used to clear the printer counter. *2

10

Electronic sort counter clear


Used to clear the electronic sort counter. *2

13

Scanner counter clear

Used to clear the scanner counter. *2

1

Main motor operation check

Execute the simulation with the developer cartridge removed, and the main
motor will rotate for 30 sec. At that time, the cooling motor rotates at a low
speed.

10

Polygon motor operation
check

Used to drive the polygon motor for 30 sec.

24

25

Contents

Details of operation

*2

*2: Display after clearing each counter
000 (0.75 sec) 3 Blank (0.35 sec) 3 000 (0.75 sec) 3 Blank (1.0 sec) 3 Repetition

AL-1611/AL-1622

SIMULATIONS

8–6

*1

Initial
value

Set range

Main
code

Sub
code

26

1

Contents
Option switch display

Details of operation

Initial
value

Set range

0

0~2

0

0~3

8

0 ~ 13

Used to display the installed option on the operation panel. (The LED corresponding to the installed option is lighted.)
Key operation

Display

Display select:


When "A" is displayed:
Magnification
Shifter: Paper empty LED
ratio display key Job separator: JAM LED
SPF: SPF select LED
RSPF: SPF JAM LED
Duplex mode: Main cassette select LED
Simplex mode: Multi manual paper feed select LED
MCU JMPER1: Top of the magnification ratio display
MCU JMPER2: 2nd of the magnification ratio display
MCU JMPER3: 3rd of the magnification ratio display
MCU JMPER7: 4th of the magnification ratio display
MCU JMPER7: 5th of the magnification ratio display
MCU JMPER7: 6th of the magnification ratio display
MCU JMPER7: 7th of the magnification ratio display
MCU JMPER8: Bottom of the magnification ratio display
When "b" is displayed:
Cassette (2nd step): No. 2 cassette select LED
Cassette (3rd step): No. 3 cassette select LED
Cassette (4th step): No. 4 cassette select LED
Memory installed: Paper empty LED
FAX: JAM LED
Printer: Main body JAM LED
ERDH: Main cassette select LED
16CPM: SPF JAM LED
20CPM: SPF select LED
Document sensor: Auto paper select LED

3

Auditor setting

Used to display the current auditor setting with the numbers at right. After
entering the set value, press the start key, and the set value is stored.
Key operation/Display
0: Built-in auditor
1: Coin vendor
2: Others

5

Counter mode setting

Used to set the print counter mode in A3.
Used to display the currently set counter value with the numbers at right. After
entering the set value, press the start key, and the set value is stored.
Key operation/Display
0: Total/Developer = 2 counts
1: Total/Developer = 1 count
2: Total/Developer = 2 counts
3: Total/Developer = 1 count

6

Destination setting

Maintenance = 2 counts
Maintenance = 2 counts
Maintenance = 1 count
Maintenance = 1 count

Used to display the current destination setting with the numbers at right.
After entering the set value, press the start key, and the set value is stored.
Key operation/Display
8: X AB series
9: X inch series (FC conformity)
10: EX AB series (FC conformity)
(Australia, Newzealand)
11: China (AB series)
12: Taiwan (AB series)
13: Germany 2 (AB series)

0: Japan
1: USA (Inch series)
2: Canada (Inch series)
3: Germany 1 (AB series)
4: UK (AB series)
5: Not used
6: France (AB series)
7: EX inch series

AL-1611/AL-1622

SIMULATIONS

8–7

Main
code

Sub
code

26

7

Contents
CRUM set value display

Details of operation

Initial
value

Set range

0

0~1

1

0~7

1

0~1

0

0~1

1

0~1

3

1, 3, 5, 7, 9

The currently set value of CRUM is displayed with the following numbers:
Key operation/Display
0: Not set
1: BTA-A
2: BTA-B

10

Model name setting

3: BTA-C
99: Conv

Used to set the model name of the machine used with the following numbers.
After entering the set value, press the start key and the set value is stored.
Key operation/Display
0: AL-1611
1: AL-1622

22

Language setting

Used to display the current setting of the language information with the number at right. After entering the set value, press the start key, and the set value
is stored.
Key operation/Display
4: Italian
5: Dutch
6: Swedish
7: Spanish

0: Japanese
1: English
2: French
3: German
30

CE mark conformity control
setting

Used to display the current setting of CE mark conformity control with the
number at right. After entering the set value, press the start key, and the set
value is stored.
Key operation/Display
0: CE mark control OFF
1: CE mark control ON

32

Fan rotation duty change
state setup

The currently set fan motor rotation duty is displayed with the following numbers. After entering the set value, press the start key to store the set value.
Key operation/Display
0: Operating 50%, standby 30%
1: Operating 80%, standby 50%

38

Cancel of stop at drum life
over

The currently set value is displayed. After entering the set value, press the
start key to store the set value.
Key operation/Display


42

Transfer timing adjustment

0: The machine stops at drum life over.
1: The machine does not stop at drum life over.
After completion of warm up, shading is performed and the currently set transfer timing adjustment value is displayed.
Key operation
Transfer timing adjustment value: Copy quantity keys
"1": 240 ms
"3": 260 ms
"5": 280 ms
"7": 300 ms
"9": 320 ms

AL-1611/AL-1622

SIMULATIONS

8–8

Main
code

Sub
code

26

50

Contents
Black-white reversion function setup

Details of operation
The current setup of black-white reversion is displayed with the following numbers. After entering the set value, press the start key to store the set value.

Initial
value

Set range

0

0~1

1

0~1

170

155 ~ 180

48

1 ~ 99

Key operation/Display
0: Black-white reversion function enabled
1: Black-white reversion function disabled
51

Sort/Group copy temporary
stop function setup

Used to set whether temporary stop for every 250-sheet print (150-sheet print
when the job separator is installed) is made or not during copying with the
sort/group function. The current setup is displayed with the following numbers.
After entering the set value, press the start key to store the set value.
Key operation/Display


30

1

Machine sensor operation
check

0: Does not stop.
1: Stops.
Used to check the sensors in the machine transport system with LED on the
operation panel.
Display

Paper entry sensor: Machine position JAM LED
Paper exit sensor: JAM LED
No. 2 cassette transport sensor: No. 2 cassette position LED

41

2

OC document sensor adjust- Used to read the document sensor input value with paper and perform the
ment
sensor detection level adjustment. For the adjustment procedure of the document sensor input value, refer to the previous descriptions.


3

Document sensor light
reception level display

Used to display the light reception level and the detection level of the document sensor. (The sensor level adjusted with SIM 41-2 is displayed.)
Key operation

Display

Light reception/Detection
level select: Magnification
ratio display key
Sensor select: Auto
magnification ratio select
key

Display at the 3rd digit
"A": Light reception level display
"b": Document detection level display
Sensor A: A3 (11 x 17) document size LED
Sensor B: A4 (8 1/2 x 14) document size LED
Sensor C: A4R (8 1/2 x 11) document size
LED
Sensor D: B4 (8 1/2 x 5 1/2) document size
LED


42

1

Developing counter clear

Used to clear the Developing counter. *2

43

1

Fusing temperature setting

Used to display the current setting of the fusing temperature at right. After
selecting the fusing temperature with the magnification ratio display key, press
the start key, and the set value is stored. The set range is 155 ~ 180°C. Use
the magnification ratio key to adjust the value by 5°C.
Key operation
Fusing temperature select: Magnification ratio display key

46

1

Copy density level adjustment

After completion of warmup, shading is performed and the currently set copy
density level is displayed. For the adjustment procedure, refer to the previous
descriptions.
Key operation

Display

Mode select:
Exposure mode select key
Copy density level:
Copy quantity keys

AL-1611/AL-1622


Auto mode: AUTO LED
Manual mode: MANUAL LED
Photo mode: PHOTO LED
Toner save mode: MANUAL + PHOTO LED
AETS mode: AUTO + PHOTO LED

SIMULATIONS

8–9

Main
code

Sub
code

48

1

Contents

Details of operation

Main scanning (front/rear)
direction magnification ratio
adjustment
(Copy/OC-SPF common)

After completion of warmup, shading is performed and the currently set main
scanning (front/rear) direction magnification ratio adjustment and the OC
mode document center off adjustment are performed. For the adjustment procedure, refer to the previous descriptions.
Key operation

OC mode sub scanning
direction magnification ratio
adjustment in copying

Set range

55

1 ~ 99

50

1 ~ 99

Display

Adjustment mode select:
Magnification ratio display
key
Manual main scanning
direction magnification ratio
adjustment Set value: Copy
quantity keys
2

Initial
value

Auto magnification ratio adjustment:
AUTO LED
Manual magnification ratio adjustment:
MANUAL LED
OC mode document center off adjustment:
PHOTO LED

After completion of warmup, shading is performed and the currently set OC
mode sub scanning direction magnification ratio adjustment in copying is performed. For the adjustment procedure, refer to the previous descriptions.
Key operation
OC mode sub scanning direction magnification ratio in copying:
Copy quantity keys

5

SPF mode sub scanning
direction magnification ratio
adjustment incopying

After completion of warmup, shading is performed and the currently set SPF
mode sub scanning direction magnification ratio adjustment in copying is performed. For the adjustment procedure, refer to the previous descriptions.
Key operation

1 ~ 99

Display

Adjustment mode select:
Auto: SPF mode sub scanning direction
Exposure mode select key magnification ratio in copying
Set value:
Copy quantity keys

33


50

1

10

Copy image position adjustment

Paper off center adjustment

1 ~ 99

After completion of warmup, shading is performed and the currently set value
is displayed. For the adjustment procedure, refer to the previous descriptions.
Key operation

Display

Adjustment mode
select:
Exposure mode select key
Set value:
Copy quantity keys

Auto: Copy lead edge adjustment
Manual: SPF lead edge adjustment

Photo: Main cassette lead edge void
adjustment
Auto + Manual: Left edge void adjustment
Auto + Photo: Rear edge void adjustment
Auto + Manual + Photo: Option cassette
lead edge void adjustment
Manual + Photo: Multi bypass tray lead
edge void adjustment
Exposure 1: Print start position adjustment

After completion of warmup, shading is performed and the currently set off
center adjustment of each paper feed port is displayed. For the adjustment
procedure, refer to the previous descriptions.
Key operation

55
77
18
48
40
18
18
55
50

1 ~ 99

55

1 ~ 99

Display

Paper feed port tray select: Main cassette:
Tray select key
Main cassette select LED
Off center adjustment value: Manual paper feed:
Manual feed select LED
numeric keys
No. 2 cassette:
No. 2 cassette select LED

13

OC mode document off
center adjustment

After completion of warmup, shading is performed and the currently set off
center adjustment value for the document in OC reading is displayed. For the
adjustment procedure, refer to the previous descriptions.
Key operation
Off center adjustment value: Copy quantity keys

*2: Display after clearing each counter
000 (0.75 sec) 3 Blank (0.35 sec) 3 000 (0.75 sec) 3 Blank (1.0 sec) 3 Repetition
AL-1611/AL-1622

SIMULATIONS

8 – 10

Main
code

Sub
code

50

16

Contents
SPF mode document off
center adjustment

Details of operation
After completion of warmup, shading is performed and the currently set off
center adjustment value for the document in SPF reading is displayed. For the
adjustment procedure, refer to the previous descriptions.

Initial
value

Set range

61

1 ~ 99

58

1 ~ 99

Key operation

18

Duplex memory reverse
position adjustment

Off center adjustment value: Copy quantity keys
After completion of warmup, shading is performed and currently set value is
displayed
Key operation


19

Duplex rear edge void
adjustment

Memory reverse position adjustment value: Copy quantity keys

Key operation


51

2

Resist amount adjustment

Display

Adjustment mode select:
Exposure mode select key
Set value:
Copy quantity keys

Auto: SPF/R-SPF rear edge void
Manual: R-SPF off center
Photo: R-SPF lead edge void

Key operation

8

SPF scan position auto
adjustment


9

SPF white level value
display


63

1

Shading data check

The mirror unit is shifted to 30mm in front of the SPF scan position. Then it is
moved by self-booting to detect the window cabinet edge.
In case of an error, "255" is displayed.
This simulation must be executed with the SPF cover open and without anything on the document table.
The mirror unit is shifted to the SPF scan position, and the white adjustment
reference level which serves as the reference for white adjustment is displayed on the display section for 30 sec.
This simulation must be executed with the SPF cover closed.
The copy lamp is shifted to the shading position and it is lighted with the reference voltage at AD conversion fixed (Vref- = 0.5V, Vref+ = 4.5V). The level of
one pixel at the center at that time is displayed.

Display section: Shading data
White correction start/pixel
position auto adjustment

52
70
1 ~ 99

Display
Auto: Main cassette
Manual: 2nd tray
Photo: Manual feed tray

Display

7

37

After completion of warmup, shading is performed and the currently set resist
amount adjustment value is displayed.

Resist amount adjustment:
Copy quantity keys
Adjustment mode select:
Exposure mode select key
53

1 ~ 99

After completion of warmup, shading is performed and currently set value is
displayed.



The mirror unit is shifted to the SPF scan position to detect the white plate
edge position.
At that time, the edge position detection pixel is displayed on the display section for 30 sec.
This simulation must be executed with the SPF cover open.
When the detected va1ue is in the range of 35~172, it is written into the
EEPROM.

64

1

Self print mode

Disregards the optical system and performs self printing in 1 by 2mode.

67

14

Printer Flash ROMData
Download


The machine enters the version up mode of the printer control PWB flash
ROM. For details, refer to the later.

AL-1611/AL-1622

SIMULATIONS

8 – 11

50
1
50

[ 9 ] USER PROGRAM
The user programs allow the parameters of certain functions to be set, changed, or canceled as desired.

1. LIST OF USER PROGRAMS
This copier has the following user programs.
Program name

Program
No

Description

Default

Parameters
0 (OFF)
1 (30sec)

Auto clear time

1

Sets the auto clear time. The copier returns to the initial settings
when the auto clear time elapses after the last copy is made.

60sec

2 (60sec)
3 (90sec)
4 (120sec)
5 (10sec)
0 (OFF)
1 (30sec)

Preheat mode

2

Sets the time that elapses before the copier enters the preheat
mode after any operation is made.

30sec

2 (60sec)
3 (90sec)
4 (120sec)
1 (30min)
2 (60min)

Auto power shut-off
timer

3

Sets the time that elapses before the copier enters the auto power
shut-off mode after any operation is made.

30min

3 (90min)
4 (120min)
5 (240min)

Stream feeding mode*
Auto power shut-off
setting

4

Enables or disables the stream feeding mode when an optional
SPF or RSPF is installed.

OFF

5

Enables or disables the auto power shut-off mode.

ON

Border line for 2 in 1 or
4 in 1*

6

Enables or disables the border line which is printed in 2 in 1 or 4 in
1 copying when an electronic sorting kit and an SPF or RSPF are
installed.

OFF

Rotation copy*

7

Enables or disables rotation of original images.

ON

Auto paper select mode

8

Enables or disables the auto paper selection.

ON

9

Enables or disables the automatic tray switching which occurs
when paper in a tray runs out. (This switching cannot switch to the
bypass tray.)

ON

Auditing mode

10

Enables or disables the auditing mode, which controls access to
copier.

OFF

Account number entry

11

Registers accounts for auditing mode.

Auto tray switching

0 (OFF)
1 (ON)
0 (OFF)
1 (ON)
0 (OFF)
1 (ON)
0 (OFF)
1 (ON)
0 (OFF)
1 (ON)
0 (OFF)
1 (ON)
0 (OFF)
1 (ON)

—

—

Account number change

12

Changes account numbers for auditing mode.

—

—

Account number deletion

13

Deletes accounts for auditing mode.

—

—

Number of copies
per account

14

Displays the total number of copies made against account numbers.

—

—

Resetting account

15

Resets all audit accounts or resets any desired individual account.

—

—
0 (0mm [0"])
1 (5mm [1/4"])

Erase width adjustment*

16

Sets the amount of the edge erase and center erase areas.

10mm [1/2"] 2 (10mm [1/2"])
3 (15mm [3/4"])
4 (20mm [1"])

Selects a pattern for 2 in 1 copying.

Layout in 2 in 1 copy*

1 (Pattern 1)

17

Pattern 1

Patern B

Patern A
AL-1611/AL-1622

USER PROGRAM

9–1

2 (Pattern 2)

Program name

Program
No

Description

Default

Selects a pattern for 4 in 1 copying.

Parameters
1 (Pattern 1)
2 (Pattern 2)
3 (Pattern 3)

Layout in 4 in 1 copy*

18

Pattern 1
4 (Pattern 4)

Patern A

Patern B

Patern C

Patern D
0 (Upper OFF, Lower OFF)

19

Enables or disables the offset function of the paper output tray. The
Upper ON,
offset function can be specified respectively for the upper and lower
Lower ON
areas separated by an optional job separator tray kit.

1 (Upper ON, Lower On)

Image rotation in
duplex copying*

20

Enables or disables image rotation (180°) of the front side in onesided to two-sided copying or two-sided to one-sided copying.

OFF

0 (OFF)

Location of the margin*

22

Selects the location of the expanded margin.

Left

Offset of paper
output tray*

2 (Upper ON, Lower OFF)
3 (Upper OFF, Lower On)
1 (ON)
1 (Left)
2 (Top)

* These programs do not affect the copier functions unless certain optional equipment is installed.

2. SETTING THE USER PROGRAMS

3. TONER CARTRIDGE LIFE

1) Press and hold the light key for more than 5 seconds until all the
alarm indicators (
,
,
, and
) blink and “- -” appears
in the copy quantity display.

To find out the approximate quantity of toner remaining, follow the procedure below.
1) Press and hold the light key for more than 5 seconds until all the
alarm indicators (
,
,
, and
) blink and “- -” appears
in the copy quantity display.

2) Enter a program number using the numeric keys.
• The selected program number will blink in the copy quantity display.
• If a mistake is made in steps 2) to 4), press the CLEAR key. The
copier will return to step 2).
For example, to change the setting of the auto power shut-off timer,
press key 3.
3) Press the START key.
• For programs 1 to 9 and 16 to 19, the entered program number
will be steadily lit on the left side of the copy quantity display and
the currently selected parameter number for the program will
blink on the right side.
• For programs 10 to 15 (programs for auditing accounts), the display varies with the program number.

2) Press and hold the copy ratio display key for more than 5 seconds.
• The approximate quantity of toner remaining will be indicated as
a percent in the copy quantity display. (“100”, “75”, “50”, “25”,
“10” or “LO” is displayed. When “LO” is displayed, the toner is
down to less than 10%.)

4) Select the desired parameter using the numeric keys.
• The entered parameter number will blink on the right side of the
copy quantity display.
• The parameters are shown in the table below.
For example, to change the setting of the auto power shut-off timer to
60 min., press key 2.

** In European countries, the default setting of the preheat mode is 1
(30 sec.). For other programs, factory-default settings in these
countries are same to those shown above with an asterisk (*).
Note: If you select “0” (OFF) in a program, the corresponding function
will be disabled.
5) Press the START key.
• The right-hand number in the copy quantity display will be
steadily lit and the entered value will be stored.

3) Press the light key.

6) To continue with other user programs, press the PRESS key and
then repeat steps 2 to 5. To exit the user program mode, press the
light key.

• All the alarm indicators will go out.

• All the alarm indicators will go out.
AL-1611/AL-1622

USER PROGRAM

9–2

[10] TROUBLE CODE LIST
1. TROUBLE CODE LIST
Trouble
code

Trouble
code

Trouble content

Trouble content

E-Sort board communication trouble

U3

29

Mirror base home position error

10

E-Sort board trouble

U9

00

Operation control PWB communication trouble

11

E-Sort ASIC error

80

Operation control PWB communication trouble (Protocol)

12

E-Sort CODEC error

81

Operation control PWB communication trouble (Parity)

13

E-Sort flash ROM error

82

Operation control PWB communication trouble (Overrun)

14

E-Sort RAM error

84

Operation control PWB communication trouble (Framing)

15

E-Sort page memory error

88

Operation control PWB communication trouble (Time-out)

16

E-Sort SIMM error

U95

Operation control PWB connection error

17

Rotation RAM error

U99

Operation control PWB connection error

80

E-Sort board communication trouble (Protocol)

81

E-Sort board communication trouble (Parity)

82

E-Sort board communication trouble (Overrun)

84

E-Sort board communication trouble (Framing)

88

E-Sort board communication trouble (Time-out)

03

LSU trouble

04

CCD white level trouble

05

CCD black level trouble

F1

06

Shifter motor trouble

F2

04

CRUM data read trouble

F5

02

Copy lamp error

F6

00

FAX board communication trouble

10

FAX board trouble

80

FAX board communication trouble (Protocol)

81

FAX board communication trouble (Parity)

82

FAX board communication trouble (Overrun)

E1

E7

00

84

2. DETAILS OF TROUBLE CODES
Main Sub
code code
E1

00

10

FAX board communication trouble (Framing)

Detail of trouble
Content

Communication trouble between MCU
and E-Sort.

Detail

Communication setup error, framing,
parity, protocol error

Cause

E-Sort PWB connector disconnection
E-Sort PWB MCU PWB harness failure
E-Sort Motherboard connector pin
breakage.
E-Sort PWB ROM defect, data failure

Check and
remedy

Check the connectors and harness of
the E-Sort PWB and the MCU PWB.
Check grounding of the machine.
Check the ROM of the E-Sort PWB.

Content

E-Sort PWB trouble

Detail

Communication trouble between MCU
and E-Sort

Cause

E-Sort PWB connector disconnection
E-Sort PWB MCU PWB harness failure
E-Sort Motherboard connector pin
breakage.
E-Sort PWB ROM defect, data failure

Check and
remedy

Check the connectors and harness of
the E-Sort PWB and the MCU PWB.
Check grounding of the machine.
Check the ROM of the E-Sort PWB.

Content

E-Sort PWB ASIC error

88

FAX board communication trouble (Time-out)

00

Printer PWB communication trouble

10

Printer PWB trouble

80

Printer PWB communication trouble (Protocol)

81

Printer PWB communication trouble (Parity)

82

Printer PWB communication trouble (Overrun)

84

Printer PWB communication trouble (Framing)

88

Printer PWB communication trouble (Time-out)

H2

00

Thermistor open detection

Detail

E-Sort PWB ASIC abnormality

H3

00

Heat roller abnormally high temperature

Cause

H4

00

Heat roller abnormally low temperature

L1

00

Mirror base feed trouble

An ASIC abnormality is detected in the
E-Sort PWB.
Control circuit hung up due to noises
ASIC peripheral circuit error

L3

00

Mirror base return trouble

L4

01

Main motor lock

Check and
remedy

Replace the E-Sort PWB.
Check grounding of the machine.

10

Job separator motor abnormality

Content

E-Sort PWB CODEC error

Detail

E-Sort PWB CODEC error

Cause

A CODEC error is detected in the E-Sort
PWB.
Control circuit hung up due to noises
CODEC peripheral circuit error

Check and
remedy

Replace the E-Sort PWB.
Check grounding of the machine.

Content

E-Sort PWB Flash ROM error

F9

11

12

L6

10

Polygon motor lock

L8

01

Zero cross pulse (FW) trouble

U2

04

EEPROM serial communication error

11

Counter check sum error

12

Adjustment value check sum error (EEPROM)

40

CRUM communication error

13

AL-1611/AL-1622

TROUBLE CODE LIST

10 – 1

Main Sub
code code
E1

13

14

15

16

17

80

81

Main Sub
code code

Detail of trouble
Detail

E-Sort PWB Flash ROM abnormality

Cause

A Flash ROM abnormality is detected in
the E-Sort PWB.
Control circuit hung up due to noises
Flash ROM peripheral circuit error

Check and
remedy

Replace the E-Sort PWB.
Rewrite the flash ROM data.
Check grounding of the machine.

Content

E-Sort PWB Work RAM error

Detail

E-Sort PWB Work RAM abnormality

Cause

A Work RAM abnormality is detected in
the E-Sort PWB.
Control circuit hung up due to noises
RAM peripheral circuit error

E1

81

82

Check and
remedy

Replace the E-Sort PWB.
Check grounding of the machine.

Content

E-Sort PWB Page Memory error

Detail

E-Sort PWB Page Memory abnormality

Cause

A Page Memory abnormality is detected
in the E-Sort PWB.
Control circuit hung up due to noises
Page Memory peripheral circuit error

Check and
remedy

Replace the E-Sort PWB.
Check grounding of the machine.

Content

E-Sort PWB SIMM error

Detail

E-Sort PWB SIMM abnormality

Cause

A SIMM abnormality is detected in the ESort PWB.
Control circuit hung up due to noises
SIMM peripheral circuit error

Check and
remedy

Replace the E-Sort PWB. Replace the
SIMM.
Check grounding of the machine.

Content

E-Sort PWB image rotating RAM error

Detail

E-Sort PWB image rotating RAM abnormality

Cause

An image rotating RAM abnormality is
detected in the E-Sort PWB.
Control circuit hung up due to noises
Image rotating RAM peripheral circuit
error

Check and
remedy

Replace the E-Sort PWB.
Check grounding of the machine.

Content

E-Sort PWB communication trouble
(protocol)

Detail

Communication trouble between MCU
and printer PWB (Protocol error)

Cause

E-Sort PWB connector disconnection
E-Sort PWB MCU PWB harness failure
E-Sort Motherboard connector pin
breakage.
E-Sort PWB ROM defect, data failure

Check and
remedy

Check the connectors and harness of
the E-Sort PWB and the MCU PWB.
Check grounding of the machine.
Check the ROM of the E-Sort PWB.

Content

E-Sort PWB communication trouble
(Parity)

Detail

Communication trouble between MCU
and printer E-Sort (Parity error)

84

88

E7

AL-1611/AL-1622

03

TROUBLE CODE LIST

10 – 2

Detail of trouble
Cause

E-Sort PWB connector disconnection
E-Sort PWB MCU PWB harness failure
E-Sort Motherboard connector pin
breakage.
E-Sort PWB ROM defect, data failure

Check and
remedy

Check the connectors and harness of
the E-Sort PWB and the MCU PWB.
Check grounding of the machine.
Check the ROM of the E-Sort PWB.

Content

E-Sort PWB communication trouble
(Overrun)

Detail

Communication trouble between MCU
and E-Sort PWB (Overrun error)

Cause

E-Sort PWB connector disconnection
E-Sort PWB MCU PWB harness failure
E-Sort Motherboard connector pin
breakage.
E-Sort PWB ROM defect, data failure

Check and
remedy

Check the connectors and harness of
the E-Sort PWB and the MCU PWB.
Check grounding of the machine.
Check the ROM of the E-Sort PWB.

Content

E-Sort PWB communication trouble
(Framing)

Detail

Communication trouble between MCU
and E-Sort PWB (Framing error)

Cause

E-Sort PWB connector disconnection
E-Sort PWB MCU PWB harness failure
E-Sort Motherboard connector pin
breakage.
E-Sort PWB ROM defect, data failure

Check and
remedy

Check the connectors and harness of
the E-Sort PWB and the MCU PWB.
Check grounding of the machine.
Check the ROM of the E-Sort PWB.

Content

E-Sort PWB communication trouble
(Time-out)

Detail

Communication trouble between MCU
and E-Sort PWB (Time-out error)

Cause

E-Sort PWB connector disconnection
E-Sort PWB and MCU PWB harness failure
E-Sort Motherboard connector pin
breakage.
E-Sort PWB ROM defect, data failure

Check and
remedy

Check the connectors and harness of
the E-Sort PWB and the MCU PWB.
Check grounding of the machine.
Check the ROM of the E-Sort PWB.

Content

LSU trouble

Detail

After the polygon motor becomes active,
BD signal (HSYNC) from the LSU is not
detected at the specified times (41 m 10
times within 20msec).

Cause

LSU connector disconnection or LSU’s
inside harness disconnection or breakage
Polygon motor rotation abnormality
Improper positioning of the laser home
position sensor in the LSU.
Laser power voltage failure
Laser emitting diode abnormality
MCU PWB abnormality

Main Sub
code code
E7

03

04

Main Sub
code code

Detail of trouble
Check and
remedy

Improper connection of the LSU connector
Check the polygon motor operation with
SIM 25-10.
Check printing with SIM64-1.
Check laser emission of laser emitting
diode.
Check the LSU unit.
Check the MCU PWB.

Content

CCD white level trouble

Detail

CCD white reference level which is read
during the copy lamp lighting is abnormal.

Cause

Flat cable installation failure to CCD unit
Dirt on the mirror, lens, and reference
white plate
Copy lamp lighting failure
CCD unit installation failure
CCD unit abnormality
MCU PWB abnormality

F2

04

Check and
remedy

Replace the toner cartridge.
Replace MCU PWB.
Replace MCU PWB EEPROM
Check and fix connection between
CRUM (toner cartridge) and MCU PWB.

F5

02

Content

Copy lamp error

Detail

Copy lamp voltage detection error

Cause

Power unit trouble Copy lamp trouble
Inverter trouble MCU PWB trouble

Check and
remedy

Replace the power unit.
Check the copy lamp ON with SIM 5-3.
Replace the copy lamp.
Replace the inverter.
Replace the MCU PWB.

Content

Communication trouble between MCU
and printer PWB (MCU detection)

Detail

Communication establishment error,
framing error, parity error, protocol error

Cause

Bad connection of printer PWB connector
Defective harness between printer PWB
and MCU PWB.
Motherboard connector pin breakage
Printer PWB ROM error, data error

Check and
remedy

Check connector/harness of printer PWB
and MCU PWB.
Check grounding of the machine.
Check printer PWB ROM.

Content

Printer PWB trouble

Detail

Communication trouble between MCU
and printer PWB

Cause

Bad connection of printer PWB connector
Defective harness between printer PWB
and MCU PWB.
Motherboard connector pin breakage
Printer PWB ROM error, data error

Check and
remedy

Check connector/harness of printer PWB
and MCU PWB.
Check grounding of the machine.
Check printer PWB ROM.

Content

Printer PWB communication trouble
(Protocol)

Detail

Communication trouble between MCU
and printer PWB (Protocol error)

Cause

Bad connection of printer PWB connector
Defective harness between printer PWB
and MCU PWB.
Motherboard connector pin breakage
Printer PWB ROM error, data error

Check and
remedy

Check connector/harness of printer PWB
and MCU PWB.
Check grounding of the machine.
Check printer PWB ROM.

Content

Printer PWB communication trouble
(Parity)

Details

Communication trouble between MCU
and printer PWB (Parity error)

Cause

Printer PWB connector disconnection
Printer PWB MCU PWB harness failure
Printer PWB mother board connector pin
breakage. Printer PWB ROM defect,
data failure

F9

00

Check and remedy Clean the mirror, the
lens, and the reference white plate.
Check the copy lamp (SIM 5-3) ON.
Carriage unit position failure
Check the sub scanning direction distortion adjustment (F rail height).
CCD unit check
MCU PWB check
05

F1

06

Content

CCD black level trouble

Detail

CCD black level which is read while the
copy lamp is off is abnormal.

Cause

Flat cable installation failure
CCD unit abnormality
MCU PWB abnormality

Check and
remedy

Check flat cable installation to the CCD
unit.
CCD unit check
MCU PWB check

Content

Shifter motor trouble

Details

The home position is not detected within
1 sec after shifter motor drive.

Cause

The shifter home position sensor is
defective.
The shifter motor is defective.
The shifter motor periphery circuit is
defective.
The condition of the MCU PWB JP4 is
wrong.
The assembly of the shifter motor unit is
improper.

Check and
remedy

F2

04

10

80

Check the shifter operation by means of
SIM3-2 and 3.
Check the harnesses and connectors.
Check whether the shifter unit is properly
assembled.
Check whether the condition of the MCU
PWB JP4 is correct.

Content

CRUM data read trouble

Detail

Communication error between CRUM
PWB and MCU PWB

Cause

CRUM PWB data error
MCU PWB error
MCU PWB EEPROM error
Disconnection between CRUM (toner
cartridge) and MCU PWB

81

AL-1611/AL-1622

TROUBLE CODE LIST

10 – 3

Detail of trouble

Main Sub
code code
F9

81

Check and
remedy

Check the connectors and harness of
the printer PWB and the MCU PWB.
Check grounding of the machine.
Check the ROM of the printer PWB.

82

Content

Printer PWB communication trouble
(Overrun)

Details

Communication trouble between MCU
and printeu PWB (Overrun error)

Cause

Printer PWB connector disconnection
Printer PWB MCU PWB harness failure
Printer PWB mother board connector pin
breakage. Printer PWB ROM defect,
data failure

84

88

Check and
remedy

Check the connectors and harness of
the printer PWB and the MCU PWB.
Check grounding of the machine.
Check the ROM of the printer PWB.

Content

Printer PWB communication trouble
(Framing)

Details

Communication trouble between MCU
and printer PWB (Framing error)

Cause

Printer PWB connector disconnection
Printer PWB MCU PWB harness failure
Printer PWB mother board connector pin
breakage. Printer PWB ROM defect,
data failure

Check and
remedy

Check the connectors and harness of
the printer PWB and the MCU PWB.
Check grounding of the machine.
Check the ROM of the printer PWB.

Content

Printer PWB communication trouble
(Time-out)

Details

Communication trouble between MCU
and printeu PWB (Time-out error)

Cause

Printer PWB connector disconnection
Printer PWB MCU PWB harness failure
Printer PWB mother board connector pin
breakage.
Printer PWB ROM defect, data failure

Check and
remedy

H2

H3

Main Sub
code code

Detail of trouble

00

00

Detail of trouble

H3

00

Check and
remedy

Check the heater lamp blinking with SIM
5-2.
When the lamp blinks normally:
Check the thermistor and the harness.
Check the MCU PWB thermistor input
circuit.
When the lamp lights up instead of blinking:
Check the lamp control circuit of the
power supply PWB and the MCU PWB.
Clear the trouble with SIM 14.

H4

00

Content

Heat roller abnormally low temperature

Detail

When the temperature does not reach
155°C within 55 sec after turning on the
power, or when it falls under 145°C during printing, or when it falls under 100°C
during pre-heating.

Cause

Thermistor failure
Heater lamp failure
MCU PWB failure
Thermostat failure
Power supply failure
Interlock switch failure

Check and
remedy

Check blinking of the heater lamp with
SIM 5-2.
When the lamp blinks normally:
Check the thermistor and the harness.
Check the MCU PWB thermistor input
circuit.
When the lamp does not light:
Check for heater lamp disconnection or
thermostat disconnection.
Check the interlock switch.
Check the power supply PWB and
MCU PWB lamp control circuit.
Clear the trouble with SIM 14.

L1

00

Content

Mirror base feed trouble

Detail

The mirror home position (MHPS) does
not turn off though the feed operation is
completed during mirror initial operation
after turning on the power.
The mirror home position (MHPS) does
not turn off during shading operation.
The mirror home position (MHPS) does
not turn on when the mirror base is
returned for the specified time after copy
feed is started and SPF scanning position shift is performed.

Cause

Mirror unit defect
Mirror home position sensor defect
MCU PWB defect Scanner wire disconnection

Check and
remedy

Check the scanning operation with SIM
1-1.

Content

Mirror base return trouble

Detail

The mirror home position (MHPS) does
not turn on though the mirror base
returning is completed during mirror initial operation after turning on the power.
The mirror home position does not turn
on when the mirror is returned to the
home position during shading.
The mirror home position (MHPS) does
not turn on when the mirror base returning is completed for the specified time
(about 6 sec) after copy return start.

Check the connectors and harness of
the printer PWB and the MCU PWB.
Check grounding of the machine.
Check the ROM of the printer PWB.

Content

Thermistor open detection

Detail

Fusing thermistor open

Cause

Thermistor defect
MCU PWB defect
Fusing section connector contact failure
Power supply failure
Fusing unit not installed

Check and
remedy

Check the harness and the connector of
the thermistor and the MCU.
Clear the self diag display with SIM 14.

Content

Heat roller abnormally high temperature

Detail

Fusing temperature of 220 ~ 240°C.

Cause

Thermistor defect
MCU PWB defect
Fusing connector connection failure
Power supply failure

L3

AL-1611/AL-1622

00

TROUBLE CODE LIST

10 – 4

Main Sub
code code
L3

L4

00

01

10

L6

L8

U2

10

01

04

Main Sub
code code

Detail of trouble
Cause

Mirror unit
Mirror home position sensor defect
MCU PWB defect Scanner wire disconnection

Check and
remedy

Check the scanning operation with SIM
1-1.

Content

Main motor lock

Detail

The main motor encoder pulse is not
detected for 400msec.

Cause

Main motor defect
Harness disconnection between the
MCU PWB and the main motor.
Control circuit failure

Check and
remedy

Check the main motor operation with
SIM 25-1.
Check the harness and the connector
between the MCU PWB and the main
motor.

Content

Job separator motor trouble

Details

When the home is not detected within
2.5 sec after the job separator tray starts
to move upwards.

Cause

The job separator upper limit detection
sensor is defective.
The job separator motor is defective.
The job separator motor periphery circuit
is defective. The condition of the MCU
PWB JP5 is wrong.

Check and
countermeasure

Check the job separator operation by
means of SIM3-2 and 4.
Check the harnesses and connectors.
Check whether the condition of the MCU
PWB JP5 is correct.

Content

Polygon motor lock

Detail

The lock signal (the specified rotation
speed signal) is not supplied within the
specified time (about 6 sec) after starting
the polygon motor rotation.

Cause

LSU connector disconnection or harness
disconnection in the LSU.

Check and
remedy

Check the operation of the polygon
motor with SIM 25-10.
Check the harness and the connector
connection. LSU replacement

Content

Zero cross pulse (FW) trouble

Detail

Zero cross pulse width is shifted by 55Hz
m 10% or more.

Cause

MCU PWB defect Power supply unit
breakdown

Check and
remedy

Check the harness and the connector.
MCU PWB replacement Power supply
unit replacement

Content

EEPROM serial communication error

Detail

Error in communication with EEPROM

Cause

EEPROM failure
Installation of uninitialized EEPROM
MCU PWB EERPOM access circuit failure

Check and
remedy

U2

11

12

40

U3

U9

29

00

Check that the EEPROM is properly set.
To prevent against loss of counter/
adjustment values, record the values
with simulation.
U2 trouble cancel with SIM 16 MCU
PWB replacement

AL-1611/AL-1622

TROUBLE CODE LIST

10 – 5

Detail of trouble
Content

Counter check sum error

Detail

Counter check sum value stored in the
EEPROM is abnormal.

Cause

EEPROM failure
Control circuit hung up by noises
MCU PWB EEPROM access circuit
defect

Check and
remedy

Check that the EEPROM is properly set.
To prevent against loss of counter/
adjustment values, record the values
with simulation.
U2 trouble cancel with SIM 16 MCU
PWB replacement

Content

Adjustment value check sum error
(EEPROM)

Detail

Adjustment value data area check sum
error

Cause

EEPROM failure
Control circuit hung up by noises
MCU PWB EEPROM access circuit failure

Check and
remedy

Check that the EEPROM is properly set.
To prevent against loss of counter/
adjustment values, record the values
with simulation.
U2 trouble cancel with SIM 16 MCU
PWB replacement

Content

CRUM communication error

Detail

Toner cartridge CRUM data read error

Cause

A toner cartridge of a different destination is installed.
EEPROM trouble
Check the destination setup.
Toner cartridge CRUM PWB trouble
MCU PWB trouble
CRUM connector disconnection

Check and
remedy

Install a specified toner cartridge.
Check the SIM 26-6 setup.
Replace the EEPROM. Replace the
toner cartridge.
Replace the MCU PWB.
Check connection of the CRUM connector.
Execute SIM 16.

Content

Mirror base home position error

Detail

Home position is not detected when
starting mirror base shift.

Cause

Mirror unit defect
Mirror home position sensor defect
MCU PWB decfect
Scanner wire disconnection

Check and
remedy

Check the scanning operation with SIM
1-1.

Content

Communication trouble between MCU
and OPE (OPE detection)

Detail

Communication setup error, framing,
parity, protocol error

Cause

Operation control PWB connector disconnection
Operation control PWB MCU PWB harness failure

Check and
remedy

Check the connectors and harness of
the operation control PWB and the MCU
PWB.
Check grounding of the machine.
Check the ROM of the operation control
PWB.

Main Sub
code code
U9

80

81

Content

Operation control PWB communication
trouble (Protocol)

Detail

Operation control PWB communication
error

Communication trouble between
MCU and the operation control
PWB (Protocol error)

Detail

Communication error between the operation control PWB and the MCU PWB
(Detected by the OPE-PWB)

Cause

Operation control PWB connector disconnection
Operation control PWB MCU PWB harness failure

Cause

Check and
remedy

Check the connectors and harness of
the operation control PWB and the MCU
PWB.
Check grounding of the machine.

Disconnection or reverse connection of
the flat cable between the Operation
control PWB and the MCU PWB.
Operation control PWB trouble
MCU PWB trouble
Connector trouble of the operation control PWB and the MCU PWB

Check and
remedy

Check insertion of or replace the flat
cable between the operation control
PWB and the MCU PWB.
Replace the operation control PWB.
Replace the MCU PWB.
Check connection of the connector of the
operation control PWB and the MCU
PWB.

Content

Operation control PWB communication
error

Detail

Communication error between the operation control PWB and the MCU PWB
(Detected by the OPE-PWB)

Cause

Disconnection or reverse connection of
the flat cable between the Operation
control PWB and the MCU PWB.
Operation control PWB trouble MCU
PWB trouble
Connector trouble of the operation control PWB and the MCU PWB

Check and
remedy

Check insertion of or replace the flat
cable between the operation control
PWB and the MCU PWB.
Replace the operation control PWB.
Replace the MCU PWB.
Check connection of the connector of the
operation control PWB and the MCU
PWB.

Content

Operation control PWB communication
trouble (Parity)

Detail

Communication trouble between MCU
and the operation control PWB (Parity
error)

Cause

Operation control PWB connector disconnection
Operation control PWB MCU PWB harness failure

84

88

U95

Detail of trouble
Content

Check and
remedy

82

Main Sub
code code

Detail of trouble

U99

Check the connectors and harness of
the operation control PWB and the MCU
PWB.
Check grounding of the machine.

Content

Operation control PWB communication
trouble (Overrun)

Detail

Communication trouble between MCU
and the operation control PWB (Overrun
error)

Cause

Operation control PWB connector disconnection
Operation control PWB MCU PWB harness failure

Check and
remedy

Check the connectors and harness of
the operation control PWB and the MCU
PWB.
Check grounding of the machine.

Content

Operation control PWB communication
trouble (Framing)

Detail

Communication trouble between MCU
and the operation control PWB (Framing
error)

Cause

Operation control PWB connector disconnection
Operation control PWB MCU PWB harness failure

Check and
remedy

Check the connectors and harness of
the operation control PWB and the MCU
PWB.
Check grounding of the machine.

Content

Operation control PWB communication
trouble (Time-out)

Detail

Communication trouble between MCU
and the operation PWB (Time-out error)

Cause

Operation control PWB connector disconnection
Operation control PWB MCU PWB harness failure

Check and
remedy

Check the connectors and harness of
the operation control PWB and the MCU
PWB.
Check grounding of the machine.

AL-1611/AL-1622

TROUBLE CODE LIST

10 – 6

[11] DISASSEMBLY AND ASSEMBLY
WARNING:Before performing the disassembly procedure, be sure to
remove the power cord to prevent against an electric shock.
No.

B. Charger wire
Installation: The spring tip must be between two reference ribs.

Item

• The charger wire must be free from twist or bending.

1

High voltage section/Duplex transport section

2

Optical section

3

Fusing section

4

Paper exit section

5

MCU

6

Optical frame unit

7

LSU

8

Tray paper feed section/Paper transport section

9

Manual multi paper feed section

10

Power section

11

SPF section 

• Be sure to put the charger wire in the V groove.

(1 )

1. HIGH VOLTAGE SECTION/DUPLEX
TRANSPORT SECTION
No.

Content

A

Transfer charger unit

B

Charger wire

(3 )
(1 )

A. Transfer charger unit

(1 ) (2 )

(2 )

(1 )

(1 )

(5 )

(4 )

(5 )
(3 )
(3 )

AL-1611/AL-1622

DISASSEMBLY AND ASSEMBLY

11 – 1

(1 )

(1 )

2. OPTICAL SECTION
No.

C. Copy lamp
Content

A

Table glass

B

Copy lamp unit

C

Copy lamp

D

Lens unit

(3 )
(1 )
(1 )

A. Table glass
(2 )

(1 )

(1 )
(3 )

(2 )

(4 )

(3 )

D. Lens unit
Note: Do not remove screws which are not indicated in the figure. If the
height of the base plate is changed, it cannot be adjusted in the
market.

B. Copy lamp unit
Disassembly: Be sure to put No. 2/3 mirror unit to the positioning plate (A).
Assembly:

Put the notched surface of wire holder (3) downward, tighten
temporarily, and install.

Adjustment:

Main scanning direction distortion balance adjustment
(4 )

(4 )

(A )

(2 )
(3 )

(A )

(2 )

(1 )

(3 )

Lens unit attachment reference
Attach the lens unit so that the lens unit number on the lens adjustment plate is aligned with the scribe line on the base plate.

(6 )
(4 )

(5 )
(5 )

Example:Lens unit number -2.8 Attach the lens unit at 2 scales in the
paper exit direction from the reference line.
Note: Never touch the other screws than the unit attachment screw.
The lens unit is supplied only in a whole unit.
AL-1611/AL-1622

DISASSEMBLY AND ASSEMBLY

11 – 2

3. FUSING SECTION
No.

C. Thermistor
Installation: Check that the thermistor is in contact with the upper heat
roller.

Contents

A

Fusing unit

B

Thermostat

C

Thermistor

D

Heater lamp

E

Upper heat roller

F

Separation pawl

G

Lower heat roller

(1 )

A. Fusing unit removal

(2 )

(1)
(1)

D. Heater lamp
Assembly: Insert the spring (A) into the hole (B) in the fusing frame.

()
()

(A)

B. Thermostat
(2 )

(1 )

(B)

(2)
(1) (2)

(3 )
(1 )

Assembly: Put the paper guide earth spring (A) under the paper guide
(B) before fusing.

AL-1611/AL-1622

DISASSEMBLY AND ASSEMBLY

11 – 3

E. Upper heat roller

(1 )

(A)

(B)

(3)

(2 )
(4)
(3)

∗

∗

Disassembly: There are three pawls on the fusing cover. Remove the
screws and slide the fusing cover to the right to remove.
The heater lamp is fixed on the fusing cover with a
screw. Slide the fusing cover to the front and remove the
screw, then remove the heater lamp.

(3)

(4)

(6 )

* Apply heat-resistive grease (UKOG-0235FCZZ).

(9 )

F. Separation pawl

(5 )
(1 0 )

(7 )

(8 )

(1)
(2)

(A )
(8 )

(2)
(1)
(1)

(B )

(2)

(C )

(3)

Assembly: Put the fusing harness (A) on the heater lamp (B) as shown
in the figure and fix them together. Place the fusing harness
inside the rib (C).

AL-1611/AL-1622

DISASSEMBLY AND ASSEMBLY

11 – 4

(3)

(3)

4. PAPER EXIT SECTION

G. Lower heat roller
Assembly: When installing the paper guide (3) before fusing, tighten
the paper guide fixing plate so that the paper guide fixing
plate (2) is in contact with the frame bottom section (A)
under fusing.

No.
A

Content
Front cabinet unit/Right cabinet unit

B

Ozone filter

C

Paper exit unit

D

Paper exit roller

A. Front cabinet unit, right cabinet disassembly

(5 )

(2 )

(4 )

(2)

(A)

(4)

(6 )

(6 )
(1 )
(3 )

(1)
(2)

(1)
(1 )

(5 )

(3)

(5 )

B. Ozone filter

* Apply heat-resistive grease (UKOG-0235FCZZ).

AL-1611/AL-1622

DISASSEMBLY AND ASSEMBLY

11 – 5

5. MCU

C. Paper exit unit

No.
A

(9)

Content
MCU

A. MCU disassembly
Note: When replacing the MCU PWB, be sure to replace the EEPROM
of the MCU PWB to be replaced.

(10)
(8)

When replacing the MCU PWB, be sure to restore the original jumper
conditions.

(6)



(7)
AL-1611/1622

(6)

(9)

JP1

JP2

JP3

JP4

JP5

JP6

JP7

JP8

u

o

o

o

o

o

o

o

u : Cut, JP
o : Don’t cut JP

(8)

D. Paper exit roller
(1)

(1)

(1)

(2)

(2)

(7)
(6)

(3)

(5)

(4)

AL-1611/AL-1622

DISASSEMBLY AND ASSEMBLY

11 – 6

(1)

6. OPTICAL FRAME UNIT
No.
A

7. LSU
No.

Content

A

Optical frame unit

LSU unit

A. LSU unit

A. Optical frame unit

(3)

(1)

(1)

Content

(4)

(2)

(1)

(1)

(1)

(1)

(1)
(2)
(1)

(3)
(5)
(5)

(2)

Installation: Install the optical unit in the sequence shown above.

Note: Do not disassemble the LSU.
Adjustment: • Image lead edge position adjustment
• Image left edge position adjustment
• Paper off-center adjustment

AL-1611/AL-1622

DISASSEMBLY AND ASSEMBLY

11 – 7

(6)

8. TRAY PAPER FEED SECTION/PAPER
TRANSPORT SECTION
No.
A

B. Drive unit
Assembly: Move down the clutch pawl as shown below, and avoid the
clutch and install.

Content
Interface frame unit

B

Drive unit

C

Solenoid (paper feed solenoid, resist roller solenoid)

D

Resist roller clutch, Resist roller

E

Paper feed clutch/Paper feed roller (Semi-circular roller)

(1)
(2)

A. Intermittent frame unit

(2)

(1)

(1)
(2)

Assembly: Do not miss the door lock pawl.

(3 )

(4 )
C. Solenoid (paper feed solenoid, resist roller solenoid)

(3)

(2)

(2)
(1)
AL-1611/AL-1622

DISASSEMBLY AND ASSEMBLY

11 – 8

D. Resist roller clutch/Resist roller

F.

Paper feed clutch

(1 )

(1)

(2 )

(2)

(3 )

9. MANUAL MULTI PAPER FEED SECTION
No.
A

(3 )

(4 )

(3 )

Content
Manual multi paper feed section

B

Manual transport clutch

C

Manual paper feed clutch

D

Manual transport roller/Manual paper feed roller

E

Multi feed solenoid

A. Manual multi paper feed
E. Paper feed roller (Semi-circular roller)
Use SIM6-10 to rotate the paper feed roller reversely, and remove the
roller.

(1 )

(2 )

(1)

(2)

(2 )
(A )

AL-1611/AL-1622

DISASSEMBLY AND ASSEMBLY

11 – 9

(3 )

B. Manual transport clutch

(4 )

(3 )

(5 )

(3 )

(2 )

(A )
(4 )

(1 )

(8 )

(1 )

C. Manual paper feed clutch
Disassembly: Set up the shutter arm (1) then remove it.
Assembly:

Install so that the boss section of the fulcrum arm (2)
comes between ribs.

(1 )
(2 )

(7 )

Disassembly: Set up the cam transmission arm (2), and remove it.
Assembly:

Install so that the cam transmission arm (2) is under the
roller arm (A).
AL-1611/AL-1622

DISASSEMBLY AND ASSEMBLY

11 – 10

(5 )

(6 )

10. POWER SECTION

D. Manual transport roller/Manual paper feed roller
Installation: Be careful of the installing direction of the manual transport roller (4).

No.
A

Content
Power unit

A. Power unit

(3 )
(3 )
(3 )

(1 )
(3 )

(2 )

(4 )
(5 )
(5 )

(4 )

(4 )

(1 )

(1 )

L O C K

T
O K

E. Multi feed solenoid
Assembly: Install so that the latches (A) and (B) move smoothly.

(1 )
(2 )
(1 )

(1 )
(B )

(A )

(2 )
(2 )

AL-1611/AL-1622

DISASSEMBLY AND ASSEMBLY

11 – 11

11. SPF SECTION 
A. Remove the SPF

Pass the SPF harness through the plate hole from the above and fix it
to the plate with the supplied two hex cap screws. (1)

1) Remove the SPF connector.

(1)

Connect the interface harness extended from the SPF, and fix with the
hand screws.

2) Remove the PWB shield plate.
Remove the six screws.

4)

Remove the SPF to copier.

Tilt the SPF backward and insert into the hinge guide.

3) Remove the SPF harness and the ring core (included together
with the unit).

B. External fitting section
Note: Remove the pawl in the arrow direction.

Pass the SPF harness through the ring core (2), and connect it to the
main PWB connector (CN11) inside the copier. (3)

(3)

2

2

(2)

★ Be careful about the direction
of the connector.

1

AL-1611/AL-1622

DISASSEMBLY AND ASSEMBLY

11 – 12

C. Paper feed unit section

3) Document feed section cover

1) Paper feed unit

2

1

1
2
1

4) Sensor PWB

1

1

1

4

2

3
2) Document transport section cover

3

1

2
1

2

3

AL-1611/AL-1622

DISASSEMBLY AND ASSEMBLY

11 – 13

5) Pickup solenoid

7) Pickup roller ass'y

Note: Remove section A of the pickup solenoid from the solenoid arm
groove.

Note: When setting the pickup roller ass'y 4, check that rib A is on the
solenoid arm rib.

A
2
1

1

A
2

4

6) Clutch gear ass'y

3
6

6
5

8) Pickup roller, paper feed roller

1

4
3

1

2
1

3

4
2
1

AL-1611/AL-1622

DISASSEMBLY AND ASSEMBLY

11 – 14

D. Interface PWB

2) Rack cover

1

2
2

3) Document length detection SW

2

1

1

1

2

1

E. Document tray section
1) Document tray

F. Drive frame section
1) Drive frame unit

2
3
1
1

1
2

1

1

AL-1611/AL-1622

DISASSEMBLY AND ASSEMBLY

11 – 15

G. Transport section

2) Transport belt

1) Clutch
Note: When assembling, check that the rib is in the clutch groove A,
and fix the E-ring.

3
1

A

3) Drive frame ass'y and drive belt

1
2

1
3

2

2) Transport roller gear

1

4) SPF motor

1

1
1

3
2

AL-1611/AL-1622

DISASSEMBLY AND ASSEMBLY

11 – 16

3) Transport roller

6) Paper feed paper guide upper
Note: When assembling, check that the paper feed paper guide upper
is set to rib A and boss B.

1
2

1

3
1
B
A

4) PS roller

7) Paper feed paper guide lower

2

1

2
1

1

8) Paper exit roller
5) Book sensor

1

1
2

AL-1611/AL-1622

DISASSEMBLY AND ASSEMBLY

11 – 17

[12] FLASH ROM VERSION UP PROCEDURE
1. MCU/E-SORT

6) Execute “mainte-Vxxx.exe” on the PC.

A. Tool
• Machine
• PC
Operates on Windows 95/98.
• Level converter (UKOG-0002QSZZ) (with serial cable)

Note: Use “mainte_vxxx.exe” ver.1.06 or later.
Since version 1.05 or before cannot identify the model (AR-162/
163/201/206/207/F201), it may erroneously perform writing. In
this case, the machine does not operate properly.

• Level converter (UKOG-0003QSZZ) (without serial cable)
• (Serial cable)

B. Procedures

7) Communication port/communication speed setting
• Select “Comport” in the option menu, and select the most suitable item with consideration of PC environment, work time, etc.

1) Connect the PC and the level converter, and start Windows.
2) Turn off the power of the machine.
3) Remove the cap at the rear of the machine.

4) Connect the serial connector.

8) Select “Download the Program Data” in the SPECIAL folder, and
transfer data.

5) Turn on the power of the machine.
• The machine enters the download mode. (All LED lamps are
turned off. The machine accepts no key operations.)
AL-1611/AL-1622

FLASH ROM VERSION UP PROCEDURE

12 – 1

9) Select the data for MCU to be transferred.

10) Select the data for the electronic sort board to be transferred.

* When the electronic sort board is not installed, this procedure is
automatically canceled. Go to procedure 11).

11) After transfer of data, turn off the machine and disconnect the connector.

Reference:If the power is turned off during the procedure or in case of a
communication error, resume the procedure from 2).

AL-1611/AL-1622

FLASH ROM VERSION UP PROCEDURE

12 – 2

AL-1611/AL-1622

13 – 1

ELECTRICAL SECTION

Dsub-25pin

CSS1 DRS1 PPD1 CASS1

DRUM INITIAL
SWITCH

THERMISTER

FEED
SOL1

CPU

COPY-OP-PWB

OPERATION PANEL

Fuser-Lamp

PICK UP
SOL1

2ndCS-PWB
CASS:CS UNIT DETECTOR
CSS :PAPER DETECTOR
PPD :PAPER PASS DETECTOR
DRS :DOOR DETECTOR

PPD2 CASS2

PICK UP
SOL2

SPF-PSOL

SPF-CLH SPF-RSOL SPF-GSOL

SPF-CON-PWB

SPF-SEN-PWB

ONLY AL-1622

SPF-Motor

L2

L1

ONLY AL-1622

CN19

CN18
CN32

I/O
EXPAND
ASIC

CN14

CN29

CN17

CN33

CN28

CPU

CN20

CN13

LAMP DRIVE
PWB

CN36

MCU-PWB

CN24

SCANNER SCANNER
HP
COVER
SENSOR SWITCH

ERDH-OP-PWB

CN22

CN38

PS-SW

CN6

POWER SUPPLY PWB

HIGH VOLTAGE
UNIT PWB

CN1

Down-Load-CON

GRAPHIC
ASIC

CN2

CCD-PWB

CRUM
DEV
SIDE
SENSOR COVER UNIT
SWITCH

CN27

PS-FAN

CN12

CN35

Mirror-Motor

CASETTE
CASETTE
PAPER
SWITCH
HAND
EMPTY PAPER IN Toner-Motor
MAIN-Motor
PAPER SENSOR SENSOR
HAND
CASETTE PS
EMPTY
PICK UP PICK UP ROLLER
SENSOR
SOL
SOL
SOL

CN15

CN10

CN16

CN26

CN11

CN23

FUSER COOLING FAN

Copy-Lamp

COPY LAMP UNIT

CN5

CN31

CN4

APC-PWB

LSU-PWB
BD-PWB

LASER SCAN UNIT
Polygon-Motor

[13] ELECTRICAL SECTION

1. OUTLINE

A. BLOCK DIAGRAM

2. MCU
A. BLOCK DIAGRAM (MCU)

CRUM
UNIT

AL-1622
only

B. CPU (HD6412351IF)
(1) pin/signal table
Pin No.

Pin name

Signal name

I/O

1

/CS1

/CS1

OUT

2

/CS0

/CS0

3

VSS

4

VSS

POW

Ground pin

5

VCC

POW

Power pin

6

A0

A0

OUT

Address bus 0

System bus

7

A1

A1

OUT

Address bus 1

System bus

8

A2

A2

OUT

Address bus 2

System bus

9

A3

A3

OUT

Address bus 3

System bus

10

VSS

POW

Ground pin

11

A4

A4

OUT

Address bus 4

System bus

12

A5

A5

OUT

Address bus 5

System bus

13

A6

A6

OUT

Address bus 6

System bus

14

A7

A7

OUT

Address bus 7

System bus

15

A8

A8

OUT

Address bus 8

System bus

16

A9

A9

OUT

Address bus 9

System bus

17

A10

A10

OUT

Address bus 10

System bus

18

A11

A11

OUT

Address bus 11

System bus

19

VSS

POW

Ground pin

20

A12

A12

OUT

Address bus 12

System bus

21

A13

A13

OUT

Address bus 13

System bus

(Pin descriptions) IN: Input pin

Function

Purpose

Area 1 chip select

SRAM chip select

L: Select

OUT

Area 0 chip select

Flash ROM chip select

L: Select

POW

Ground pin

OUT: Output pin BIDIR: Bi-directional pin ODN: Open drain output pin

AL-1611/AL-1622

ELECTRICAL SECTION

13 – 2

Descriptions

TR1: 3-state output pin

POW: Power pin

Pin No.

Pin name

Signal name

I/O

Function

22

A14

A14

OUT

Address bus 14

System bus

23

A15

A15

OUT

Address bus 15

System bus

24

A16

A16

OUT

Address bus 16

System bus

25

A17

A17

OUT

Address bus 17

System bus

26

A18

A18

OUT

Address bus 18

System bus

27

A19

A19

OUT

Address bus 19

System bus

28

VSS

POW

Ground pin

29

A20

A20

OUT

Address bus 20

System bus

30

/IRQ5

/SPFCOVER

IN

Interruption request 5

SPF cover sensor interrup- 1: Cover close
tion

31

/IRQ6

/OCCOVER

IN

Interruption request 6

OC cover sensor interrup- 0: Cover close
tion

32

/IRQ7

MHP

IN

Interruption request 7

Mirror home position sensor 1: Home position
interruption

33

/IRQ3

/SPFPAPER

IN

Interruption request 3

S P F p a p e r p a s s s e n s o r 0: Paper presence
interruption

34

/IRQ2

/CPUSYNC

IN

Interruption request 2

Horizontal sync signal inter- 0: Effective
ruption

35

VSS

POW

Ground pin

POW

Ground pin

Purpose

Descriptions

36

VSS

37

/IRQ1

/FW

IN

Interruption request 1

Zero cross interruption

0: Effective

38

/IRQ0

/LOOPINT

IN

Interruption request 0

Loop interruption

0: Effective

39

VCC

POW

Power pin

40

D0

D0

BIDIR

Data bus 0

System bus

41

D1

D1

BIDIR

Data bus 1

System bus

42

D2

D2

BIDIR

Data bus 2

System bus

43

D3

D3

BIDIR

Data bus 3

System bus

44

VSS

POW

Ground pin

45

D4

D4

BIDIR

Data bus 4

System bus

46

D5

D5

BIDIR

Data bus 5

System bus

47

D6

D6

BIDIR

Data bus 6

System bus

48

D7

D7

BIDIR

Data bus 7

System bus

49

D8

D8

BIDIR

Data bus 8

System bus

50

D9

D9

BIDIR

Data bus 9

System bus

51

D10

D10

BIDIR

Data bus 10

System bus

52

D11

D11

BIDIR

Data bus 11

System bus

53

VSS

POW

Ground pin

54

D12

D12

BIDIR

Data bus 12

System bus

55

D13

D13

BIDIR

Data bus 13

System bus

56

D14

D14

BIDIR

Data bus 14

System bus

57

D15

D15

BIDIR

Data bus 15

System bus

58

VCC

POW

Power pin

59

P30



OUT

General port 30

60

TXD1

TXD1

OUT

SCI channel 1 serial trans- Service connector
mission

61

P32

SDA

ODN

62

RXD1

RXD1

IN

63

P34

SCL

64

P35

/FROMUP

65

VSS

66

/DREQ0

67

VSS

(Pin descriptions) IN: Input pin

EEPROM control

L: Level fixing output
UART serial output
12CBUS data line

SCI channel 1 serial recep- Service connector
tion

UART input

ODN

General port 34

EEPROM control

12CBUS clock line

IN

General port 35

Service connector

0: Service mode

POW
/DREQ0

General port 32

(Not used)

IN
POW

Ground pin
DMAC channel 0 external Mirror and SPF motor accel- 0: Request effective
request
eration/reduction control
Ground pin

OUT: Output pin BIDIR: Bi-directional pin ODN: Open drain output pin
AL-1611/AL-1622

ELECTRICAL SECTION

13 – 3

TR1: 3-state output pin

POW: Power pin

Pin No.

Pin name

Signal name

I/O

Function

Purpose

Descriptions

68

VSS

POW

Ground pin

69

/CS5



OUT

Area 5 chip select

70

/DREQ1

/DREQ1

IN

71

P63

POFFR

OUT

General port 63

Power off relay control

72

P27

/ESPAGE

IN

General port 27

ERDH option page signal 0: Page effective
detection

73

P26

/PCLPAGE

IN

General port 26

PCl operation page signal 0: Page effective
detection

74

P25

/FAXPAGE

IN

General port 25

F A X o p ti o n p a g e s i g n a l 0: Page effective
detection

75

P24

/READY

OUT

General port 24

Machine ready signal

L: Machine ready state

76

P23

/PWOFF

OUT

General port 23

Power off signal

L: Power interruption detecting state

77

P22

/SCANSP

OUT

General port 22

Scan stop signal

L: Scanning operation interruption

78

P21

/SCANST

OUT

General port 21

Scan start signal

L: Scanning operation effective

79

P20

/PRSTART

OUT

General port 20

Print start signal

L: Printing effective

(Not used)

L: Select

DMAC channel 1 external Lifter and separator motor 0: Request effective
request
acceleration/reduction control
H: AC switch OFF

80

/WDTOVR



OUT

Watch dog timer overflow

System reset

L: System restart

81

/RES



IN

System reset

System reset

0: Power on reset

82

NMI



IN

Non-maskable interruption (Not used)
request

1: Level fixing input

83

/STBY



IN

Stand-by

1: Level fixing input

84

VCC

POW

Power pin

(Not used)

85

XTAL



IN

Oscillation pin

Oscillator (19.6608MHz)

86

EXTAL



OUT

Oscillation pin

Oscillator (19.6608MHz)

87

VSS

88

â

89

VCC

CPUCLK

POW

Ground pin

OUT

System clock

POW

Power pin

System clock

19.6608MHz clock output
L: Address effective

90

/AS

/AS

OUT

Address strobe

System bus

91

/RD

/RD

OUT

Lead strobe

System bus

L: Lead effective

92

/HWR

/HWR

OUT

Highlight enable

System bus

L: Highlight effective

93

/LWR

/LWR

OUT

Row write enable

System bus

L: Row write effective

94

PF2

/TMEN

OUT

General port F2

Toner motor drive control

L: Rotating

95

PF1

PMD

OUT

General port F1

Polygon motor drive control

H: Rotating

96

PF0

MMD

OUT

General port F0

Main motor drive control

H: Rotating

97

P50

/MMRDY

IN

General port 50

Main motor ready signal

0: Rotation stable state

98

P51

/PMRDY

IN

General port 51

Polygon motor ready signal

0: Rotation stable state

99

VSS

POW

Ground pin

100

VSS

POW

Ground pin

101

P52

/PRLINE

OUT

General port 52

Print line signal

L: Printing effective

102

P53

/SCLINE

OUT

General port 53

Scan line signal

L: Scanning operation effective

103

AVCC

POW

Analog power pin

104

VREF

105

AN0

POW
RTH

IN

Analog reference pin
Analog input 0

Fusing thermistor temperature detection

106

AN1



IN

Analog input 1

(Not used)

107

AN2



IN

Analog input 2

(Not used)

108

AN3

TONER

IN

Analog input 3

Toner sensor

5V: Toner empty

109

AN4



IN

Analog input 4

(Not used)

110

AN5



IN

Analog input 5

(Not used)

111

DA0

DA0

OUT

Analog output 0

CCD reference + side

(Pin descriptions) IN: Input pin

OUT: Output pin BIDIR: Bi-directional pin ODN: Open drain output pin
AL-1611/AL-1622

ELECTRICAL SECTION

13 – 4

TR1: 3-state output pin

POW: Power pin

Pin No.

Pin name

Signal name

I/O

Function

112

DA1

DA1

OUT

Analog output 1

113

AVSS

POW

Analog ground pin

114

VSS

POW

Ground pin

Purpose

Descriptions

CCD reference − side

115

TCLKD

LFTCLK

IN

Timer clock external input

Separator motor step count

Separator motor clock input

116

TIOCA2

TMCLK

OUT

Timer clock external output

Toner motor clock

960Hz clock output

117

TCLKC

SFTCLK

IN

Timer clock external input

Shifter motor step count

Shifter motor clock input

118

TIOCA1

PMCLK

OUT

Timer clock external output

Polygon motor clock

2078.74Hz clock output

119

TCLKB

SPFCLK

IN

Timer clock external input

SPF motor step count

SPF motor clock input

120

TCLKA

MIRCLK

IN

Timer clock external input

Mirror motor step count

Mirror motor clock input

121

/DACK1



OUT

DMAC channel 1 acknowl- (Not used)
edge

L: Acknowledge effective

122

/DACK0



OUT

DMAC channel 0 acknowl- (Not used)
edge

L: Acknowledge effective

123

MD0



IN

Operation mode setting pin O p e r a t i o n m o d e s e t t i n g Operation mode 4
0
(MODE 4)

124

MD1



IN

Operation mode setting pin O p e r a t i o n m o d e s e t t i n g Operation mode 4
1
(MODE 4)

125

MD2



IN

Operation mode setting pin O p e r a t i o n m o d e s e t t i n g Operation mode 4
2
(MODE 4)

126

PG0

RY/BY

IN

General port G0

Flash ROM busy signal

127

/CS3

/CS3

OUT

Area 3 chip select

I/ O ex tension AS IC chip L: Select effective
select

128

/CS2

/CS2

OUT

Area 2 chip select

Image ASIC chip select

(Pin descriptions) IN: Input pin

OUT: Output pin BIDIR: Bi-directional pin ODN: Open drain output pin

0: Busy state

L: Select effective

TR1: 3-state output pin

POW: Power pin

C. IMAGE ASIC (HG73C039FD)
(1) Outline
The following figure shows the block diagram of the ASIC.
The ASIC is composed of the following three blocks; the image process section, the print control section, and the I/F section.
The image process section processes the image data from the CCD PWB according to the operation mode, such as shading, AE process, resolution
conversion and zooming.
The print control section outputs the image-processed data during copying to the LSU (Laser unit) in synchronization with writing timing of the
LSU.The I/F section controls communication of interface (IEEE1284) with the host PC and controls DRAM of send/receive data buffer with the host
PC. (Only for models with the printer function)
The ASIC is controlled by the CPU which writes the operation mode and the set values necessary for each operation mode to the ASIC control register.
Scan start

ASIC
Print control section

Image process section
CCD drive

CCD
PWB

LSU
Print data process circuit

Resolution conversion,
Zooming, lmage
process circuit

AE

Shading

HSYNC

PRINT control

VSYNC

SRAM control

DRAM control

I/F section

SRAM
32KB
x2

IEEE1284 control

ASIC control resistor

TO PCI/F
PWB
(Only for models
withthe printer
function)

DRAM
6MB or 4MB
To CPU bus

AL-1611/AL-1622

ELECTRICAL SECTION

13 – 5

(2) pin/signal table
PIN No.

Signal Name

IN/OUT

Description

PIN No.

Signal Name

IN/OUT

Description

MAD0

OUT

Address bus of DRAM (page
memory)

1

/SCANSP

IN

Scanner process interrupt
signal

46

2

/PRSTART

IN

Print start trigger signal

47

GND

Power

MAD1

OUT

3

TMON

IN

Toner motor ON/OFF

48

4

TMCLK

IN

Toner motor reference clock

49

MAD2

OUT

50

MAD3

OUT

51

MAD4

OUT

MAD5

OUT

5

3.3V

Power

6

CPUAD7

IN

CPU address bus

7

CPUAD6

IN

52

8

GND

Power

53

MAD6

OUT

54

MAD7

OUT

9

CPUAD5

IN

CPU address bus

10

CPUAD4

IN

55

MAD8

OUT

MAD9

OUT

11

CPUAD3

IN

56

12

CPUAD2

IN

57

3.3V

Power

58

MAD10

OUT

Horizontal synchronization
signal

59

MAD11

OUT

60

GND

Power

Interruption request signal

13

CPUAD1

IN

14

/CPUSYNC

OUT

Address bus of DRAM (page
memory)

Address bus of DRAM (page
memory)

15

/INTR

OUT

61

/CAS0

OUT

16

/CPUCS

IN

CPU chip select signal

62

/CAS1

OUT

17

/RESET

IN

Reset signal

63

/OE

OUT

18

5V

Power

Read enable signal of DRAM
(page memory)

19

GND

Power

64

/WE

OUT

Write enable signal of DRAM
(page memory)

65

OUTD0

OUT

(Not used)

66

OUTD1

OUT

67

OUTD2

OUT

68

OUTD3

OUT

69

3.3V

Power

20

3.3V

Power

21

GND

Power

22

MDATA15

IN/OUT

23

MDATA14

IN/OUT

24

MDATA13

IN/OUT

25

MDATA12

IN/OUT

26

MDATA11

IN/OUT

27

MDATA10

IN/OUT

28

MDATA9

IN/OUT

29

MDATA8

IN/OUT

30

MDATA7

IN/OUT

31

3.3V

Power

32

MDATA6

IN/OUT

33

MDATA5

IN/OUT

34

GND

Power

35

MDATA4

IN/OUT

36

MDATA3

IN/OUT

37

MDATA2

IN/OUT

38

MDATA1

IN/OUT

39

MDATA0

IN/OUT

40

/RAS0

OUT

RAS signal 0 of DRAM (page
memory)

41

/RAS1

OUT

42

/RAS2

OUT

43

/RAS64

OUT

44

3.3V

Power

45

/RAS16

OUT

Data bus of DRAM (page
memory)

Data bus of DRAM (page
memory)

Data bus of DRAM (page
memory)

70

OUTD4

OUT

71

OUTD5

OUT

72

GND

Power

73

OUTD6

OUT

74

OUTD7

OUT

75

OUTD8

OUT

76

OUTD9

OUT

77

OUTD11

OUT

78

OUTD10

OUT

79

OUTD12

OUT

80

OUTD13

OUT

81

OUTD14

OUT

82

OUTD15

OUT

83

/HSYNC

OUT

84

/PCLPRD

IN

85

/PCLREQ

OUT

RAS signal 1 of DRAM (page
memory)

86

/PCLACK

IN

87

/PCLCS

IN

RAS signal 2 of DRAM (page
memory)

88

3.3V

Power

89

GND

Power

90

5V

Power

91

GND

Power

92

/FAXPRD

IN

(Not used)

(Not used)

AL-1611/AL-1622

ELECTRICAL SECTION

13 – 6

CAS signal of DRAM (page
memory)

(Not used)

(Not used)

(Not used)

PIN No.

Signal Name

IN/OUT

93

/FAXREQ

OUT

94

/FAXACK

IN

95

3.3V

Power

96

/FAXCS

IN

97

/ESPRD

IN

98

GND

Power

99

/ESREQ

OUT

100

/ESACK

IN

101

/ESCS

IN

102

PARAD0

IN/OUT

103

PARAD1

IN/OUT

104

PARAD2

IN/OUT

105

PARAD3

IN/OUT

106

PARAD4

IN/OUT

107

PARAD5

IN/OUT

108

5V

Power

109

PARAD6

IN/OUT

110

PARAD7

IN/OUT

111

GND

Power

112

/REV

OUT

113

INIT

IN

114

/SLCTIN

IN

115

/AUTOFD

IN

116

/STB

IN

117

/ACK

OUT

118

BUSY

OUT

119

PE

OUT

120

/FAULT

OUT

121

5V

Power

122

SLCT

OUT

123

/TESTPIN0

IN

124

GND

Power

Description
(Not used)

(Not used)

PIN No.

Signal Name

IN/OUT

Description

140

SCS1

OUT

Chip select line to SRAM
before area separation

141

SOE0

OUT

Read enable line to SRAM
before area separation

142

SWE0

OUT

Write enable line to SRAM
before area separation

143

SCS0

OUT

Chip select line to SRAM
before area separation
Data line to SRAM before are
separation

(Not used)

(Not used)

(Not used)

(Not used)
High: Normal Low: Test

144

SD00

IN/OUT

145

SD01

IN/OUT

146

5V

Power

147

SD02

IN/OUT

148

SD03

IN/OUT

149

GND

Power

150

SD04

IN/OUT

151

SD05

IN/OUT

152

SD06

IN/OUT

153

SD07

IN/OUT

154

SAD0

OUT

155

SAD1

OUT

156

SAD2

OUT

157

SAD3

OUT

158

SAD4

OUT

159

SAD5

OUT

160

SAD6

OUT

161

SAD7

OUT

162

GND

Power

163

SAD8

OUT

Data line to SRAM before are
separation

Data line to SRAM before are
separation

Address line to SRAM before
area separation

Address line to SRAM before
area separation

164

SAD9

OUT

165

SAD10

OUT

166

SAD11

OUT

167

SAD12

OUT

168

SAD13

OUT

169

/f1

OUT

CCD drive signal transfer
clock (First phase)

OUT

CCD drive signal transfer
clock (Second phase)
CCD drive signal shift pulse

125

PFCLK

IN

Write clock

126

/TESTPIN1

IN

High: Normal Low: Test

170

/f2

127

/SYNCEN

OUT

Jitter adjustment IC trigger
signal

171

/SH

OUT

128

SD10

IN/OUT

172

5V

Power

129

SD11

IN/OUT

Data line to SRAM before are
separation

173

RS

OUT

CCD drive signal reset pulse

130

SD12

IN/OUT

174

SP

OUT

131

SD13

IN/OUT

CCD drive signal sampling
hold pulse

132

SD14

IN/OUT

175

GND

Power

133

5V

Power

176

CP

OUT

A/D conversion IC latch clock

177

BCLK

OUT

CCD shield output latch signal

178

IDIN0

IN

179

IDIN1

IN

Image scan data (after 8bit A/
D conversion)

180

IDIN2

IN

IDIN3

IN

134

SD15

IN/OUT

135

SD16

IN/OUT

136

GND

Power

137

SD17

IN/OUT

Data line to SRAM before are
separation

Data line to SRAM before are
separation

138

SOE1

OUT

Read enable line to SRAM
before area separation

181
182

IDIN4

IN

139

SWE1

OUT

Write enable line to SRAM
before area separation

183

IDIN5

IN

184

IDIN6

IN

AL-1611/AL-1622

ELECTRICAL SECTION

13 – 7

PIN No.

Signal Name

IN/OUT

Description

185

5V

Power

186

IDIN7

IN

187

/SDCLK

OUT

188

GND

Power

189

SFCLK

IN

CCD drive clock (48MHz)

190

TEST port 0

IN

High: Normal Low: Test

191

/SYNC

IN

Horizontal synchronization
signal (HSYNC) from LSU

192

/LD

OUT

Image scan data (after 8bit A/
D conversion)
Effective image area signal

Laser drive signal

193

/LEND

OUT

Laser APC signal

194

/VIDEOCS

OUT

Video data control

195



OUT

196



OUT

197

3.3V

Power

198



OUT

199



OUT

200

GND

Power

201



OUT

202



OUT

203



OUT

204



OUT

205



OUT

206



OUT

207



OUT

208



OUT

209



OUT

210

3.3V

Power

211



OUT

NC

NC

NC

PIN No.

Signal Name

IN/OUT

232

CPUD14

IN/OUT

233

CPUD13

IN/OUT

234

CPUD12

IN/OUT

235

CPUD11

IN/OUT

212



OUT

GND

Power

214

/PCLPCS

OUT

PCL option print data control

215

/FAXPCS

OUT

FAX option print data control

216

/ESPCS

OUT

Electronic sort option print
data control

217



OUT

NC

218

CV_START

OUT

Copy vendor control

219

CV_COUNT

OUT

220

CV_SIZE3

OUT

221

CV_SIZE2

OUT

222

CV_SIZE1

OUT

223

5V

Power

224

CV_SIZE0

OUT

225

CV_DPX

OUT

226

GND

Power

227

CV_CA

OUT

Copy vendor control

228



OUT

NC

5V

Power

237

CPUD10

IN/OUT

238

CPUD9

IN/OUT

239

GND

Power

240

CPUD8

IN/OUT

241

CPUD7

IN/OUT

242

CPUD6

IN/OUT

243

CPUD5

IN/OUT

244

CPUD4

IN/OUT

245

CPUD3

IN/OUT

246

CPUD2

IN/OUT

247

CPUD1

IN/OUT

248

CPUD0

IN/OUT

249

3.3V

Power

250

/CPUWR

IN

CPU write signal

251

/CPURD

IN

CPU read signal

252

GND

Power

253

CPUCLK

IN

254

GND

Power

255

TEST PORT1

IN

High: Normal Low: Test

256

/SCANST

IN

Scanner process start signal

Copy vendor control

229

TM

OUT

Toner motor drive output (+)

230

TM_

OUT

Toner motor drive output (−)

231

CPUD15

IN/OUT

CPU data bus

AL-1611/AL-1622

ELECTRICAL SECTION

13 – 8

CPU data bus

236

NC

213

Description

CPU data bus

CPU data bus

CPU system clock

D. I/O ASIC
(1) pin/signal table
Pin No.

Pin name

1

GND

Signal name

POW

I/O

2

GND

POW

Purpose

Descriptions

3

SCK

IN

0: Level fixing input

4

AMC

IN

0: Level fixing input

5

SMC

IN

0: Level fixing input

6

UART0SIN/
SIN

OPECMD

IN

Operation panel command interface

7

UART0SOUT/
SOT

OPESTS

OUT

Operation panel command interface

8

UART0CTSB

/OPESRDY

IN

Operation panel command interface

9

UART0RTSB

/OPECRDY

OUT

Operation panel command interface

10

GND

11

UART1SIN

OPECMD

POW
IN

Electronic sort option command interface

12

UART1SOUT

OPESTS

OUT

Electronic sort option command interface

13

UART1CTSB

/OPESRDY

IN

Electronic sort option command interface

14

UART1RTSB

/OPECRDY

OUT

Electronic sort option command interface

15

UART2SIN

OPECMD

IN

FAX option command interface

16

VCC

17

UART2SOUT

OPESTS

POW
OUT

FAX option command interface

18

UART2CTSB

/OPESRDY

IN

FAX option command interface

19

UART2RTSB

/OPECRDY

OUT

FAX option command interface

20

GND

POW

21

VCC

POW

22

GND

23

UART3SIN

OPECMD

POW
IN

PQL option command interface

24

UART3SOUT

OPESTS

OUT

PQL option command interface

25

UART3CTSB

/OPESRDY

IN

PQL option command interface

26

UART3RTSB

/OPECRDY

OUT

PQL option command interface

27

VCC

28

DSLED1

LED1

OUT

3; Beam document size sensor control

29

DSLED2

LED2

OUT

3; Beam document size sensor control

30

DSLED3

LED3

OUT

31

DSIN0

DSIN1

IN

32

GND

33

DSIN1

DSIN2A

IN

34

DSIN2

DSIN2B

IN

2: Beam document size sensor B detection

35

DSIN3

DS3IN

IN

3: Beam document size sensor detection

36

PMC0POUT0

MIRMODA

37

VCC

38

PMC0POUT1

MIRMODB

39

PMC0POUT2

/MIRMODA

40

VCC

POW

41

GND

POW

POW

3; Beam document size sensor control
1: Beam document size sensor detection

POW

OUT

2: Beam document size sensor A detection

Mirror motor phase A drive

H: Drive

OUT

Mirror motor phase B drive

H: Drive

OUT

Mirror motor phase /A drive

H: Drive

POW

42

GND

43

PMC0POUT3

/MIRMODB

POW
OUT

Mirror motor phase /B drive

H: Drive

44

PMC2POUT0

SFTDA

OUT

Shifter motor phase A drive

H: Drive

45

PMC2POUT1

SFTDB

OUT

Shifter motor phase B drive

H: Drive

46

PMC2POUT2

/SFTDA

OUT

Shifter motor phase /A drive

H: Drive

47

VCC

POW

Pin descriptions) IN: Input pin OUT: Output pin BIDIR: Bi-directional pin ODN: Open drain output pin TR1: 3-state output pin POW: Power pin

AL-1611/AL-1622

ELECTRICAL SECTION

13 – 9

Pin No.

Pin name

Signal name

I/O

Purpose

Descriptions

48

PMC2POUT3

/SFTDB

OUT

Shifter motor phase /B drive

H: Drive

49

PMC3POUT0

LFTDA

OUT

Separator motor phase A drive

H: Drive

50

PMC3POUT1

LFTDB

OUT

Separator motor phase B drive

H: Drive

51

PMC3POUT2

/LFTDA

OUT

Separator motor phase /A drive

H: Drive

52

GND

53

PMC3POUT3

/LFTDB

OUT

Separator motor phase /B drive

H: Drive

54

PMC4POUT0

DPXDA

OUT

Duplex motor phase A drive

H: Drive

55

PMC4POUT1

DPXDB

OUT

Duplex motor phase B drive

H: Drive

56

PMC4POUT2

/DPXDA

OUT

Duplex motor phase /A drive

H: Drive

57

TESTB

IN

1: Level fixing input

58

TESTB

IN

1: Level fixing input

59

GND

POW

60

GND

POW

61

VCC

POW

62

PMC4POUT3

/DPXDB

OUT

Duplex motor phase /B drive

H: Drive

63

PWM0POUT

PFANMD

OUT

Power fan motor drive

H: Drive

64

PWM1POUT

TFANMD

OUT

Fusing fan motor drive

H: Drive

POW

65

P0OUT8

SOPHIA

OUT

(Not used)

66

P0OUT9

/LOOPINT

OUT

Loop interruption control

67

P0OUT10



OUT

(Not used)

68

P0OUT11



OUT

(Not used)

69

GND

70

P0OUT12

MIRMO0

OUT

Mirror motor phase current control 0

H: Power down

71

P0OUT13

MIRMO1

OUT

Mirror motor phase current control 1

H: Power down

72

P0OUT14

PDOWN

OUT

SPF motor phase current control

H: Power down

73

P0OUT15



OUT

(Not used)

L: Interruption

POW

74

P1OUT12

SPFPSOL

OUT

SPF pickup solenoid drive

H: Drive

75

P1OUT13

SPFGSOL

OUT

SPF gate solenoid

H: Drive

76

P1OUT14

SPFRSOL

OUT

SPF release solenoid drive

H: Drive

SPF clutch solenoid

H: Drive

Paper in sensor detection

1: Paper presence

1: Paper presence

77

VCC

78

P1OUT15

SPFCLH

POW
OUT

79

P0IN0

PIN

IN

80

GND

POW

81

VCC

POW

82

P0IN1

POUT

IN

Paper out sensor detection

83

P0IN2

PDPX

IN

Duplex control sensor detection

0: Paper presence

84

P0IN3

LFTHP

IN

Separator home position sensor detection

1: Home position

85

GND

86

P0IN4

/SFTHP

POW
IN

Shifter home position sensor detection

0: Home position

87

P0IN5

PFULL

IN

Tray paper full sensor detection

1: Paper full

88

P0IN6

MHP

IN

Mirror home position sensor detection

1: Home position

89

VCC

POW

90

GND

POW

91

PFCLK

92

GND

POW

93

GND

POW

PFCLK

IN

Dot count control

94

LDB

/VIDEO

IN

Dot count control

0: Effective

95

LENDB

S/H

IN

Dot count control

0: Effective

96

VCC

97

P0IN7

/CV_COPY

IN

Coin vendor copy enable detection

0: Copy enabled

98

P0IN8

/HTEMP

IN

Fusing thermistor abnormally high temperature 0: Abnormally high temperature
detection

POW

Pin descriptions) IN: Input pin OUT: Output pin BIDIR: Bi-directional pin ODN: Open drain output pin TR1: 3-state output pin POW: Power pin
AL-1611/AL-1622

ELECTRICAL SECTION

13 – 10

Pin No.

Pin name

Signal name
/THOPEN

I/O
IN

Purpose

Descriptions

99

P0IN9

100

VCC

POW

Fusing thermistor disconnection detection

0: Wire disconnection

101

GND

POW

102

P0IN10

CASETTE

103

P0IN11

/CPEMPTY

IN

Copier cassette switch detection

1: Cassette installed

IN

Copier cassette paper empty sensor detection

104

GND

0: Paper empty

105

P0IN12

HPEMPTY

IN

Manual feed tray paper empty sensor detection

1: Paper empty

106

P0IN13

/DEV

IN

Developing unit installation detection

0: Unit installed

107

P0IN14

DRUM

IN

Drum initial switch detection

1: Drum initial

108

P0IN15

/CSW

IN

Side cover switch detection

0: Cover close

109

P1IN0

/PMEMO

IN

Memory print operation setup jumper detection

1: Operation enabled

110

P1IN1

/CSPEED

IN

Copy speed setup jumper detection

"1: 20ppm,

111

P1IN2

/DPXSW

IN

Duplex print operation setup jumper detection

1: Operation enabled

112

VCC

113

P1IN3

/SFTSW

IN

Shifter operation setup jumper detection

1: Operation enabled

114

P1IN4

/LFTSW

IN

Separator operation setup jumper detection

1: Operation enabled

115

P1IN5

/INCHSW

IN

Inch series document size sensor setup jumper 1: Operation enabled
detection

116

P1IN6

/JPNABSW

IN

Japan AB series document size sensor setup 1: Operation enabled
jumper detection

117

P1IN7

/EXJABSW

IN

EX AB series document size sensor setup jumper 1: Operation enabled
detection

118

P1IN8

/ESREADY

IN

Electronic sort board option installation detection

0: Option installed

119

P1IN9

/FAXREADY

IN

FAX board option installation detection

0: Option installed

POW

POW

120

VCC

POW

121

GND

POW

122

GND

POW

123

TEST

IN

(Not used)

0: Level fixing input

124

TEST

IN

(Not used)

0: Level fixing input

125

TEST

IN

(Not used)

0: Level fixing input
0: Option installed

126

P1IN10

/PCLREADY

IN

FAX board option installation detection

127

P1IN11

/SPFOPEN

IN

SPF unit float sensor detection

128

P1IN12



IN

(Not used)

129

P1IN13



IN

(Not used)

130

VCC

131

P1IN14



IN

(Not used)

132

P1IN15



IN

(Not used)

133

P1OUT0

HPSOL

OUT

Manual feed tray pickup solenoid drive

H: Drive

134

P1OUT1

CPSOL

OUT

Copier cassette pickup solenoid drive

H: Drive

135

GND

136

P1OUT2

PSRSOL

OUT

PS roller solenoid drive

H: Drive

137

P1OUT3



OUT

(Not used)

138

P1OUT4



OUT

(Not used)

139

GND

POW

POW

POW

140

VCC

141

P1OUT5



POW
OUT

(Not used)

142

P1OUT6

PSOL1

OUT

Option cassette 1 pick up solenoid drive

H: Drive

143

P1OUT7

FSOL1

OUT

Option cassette 1 feed solenoid drive

H: Drive

144

P1OUT8

PSOL2

OUT

Option cassette 2 pickup solenoid drive

H: Drive

145

GND

POW

146

P1OUT9

FSOL2

OUT

Option cassette 2 feed solenoid drive

H: Drive

147

P1OUT10

PSOL3

OUT

Option cassette 3 pickup solenoid drive

H: Drive

Pin descriptions) IN: Input pin OUT: Output pin BIDIR: Bi-directional pin ODN: Open drain output pin TR1: 3-state output pin POW: Power pin

AL-1611/AL-1622

ELECTRICAL SECTION

13 – 11

Pin No.

Pin name

Signal name

I/O

Purpose

148

P1OUT11

FSOL3

OUT

Option cassette 3 feed solenoid drive

149

SELOUT0

SELA

OUT

Option sensor select control

150

VCC

151

SELOUT1

SELB

OUT

Option sensor select control

152

SELOUT2

SELC

OUT

Option sensor select control

153

YIN0

YSPF

IN

SPF option related sensor

154

YIN1

Y1

IN

Option cassette 1 related sensor detection

155

GND

156

YIN2

Descriptions
H: Drive

POW

POW
Y2

IN

Option cassette 2 related sensor detection

157

YIN3

Y3

IN

158

P0OUT0

HL

OUT

Halogen lamp control

Option cassette 3 related sensor detection
H: Lamp ON

159

P0OUT1

CL

OUT

Copy lamp control

H: Lamp ON

H: Relay ON

160

VCC

POW

161

GND

POW

162

P0OUT2

PR

OUT

Power relay control

163

P0OUT3

MC

OUT

Main charger voltage control

H; Voltage ON

164

P0OUT4

TC

OUT

Transfer charger voltage control

H; Voltage ON

165

GND

166

P0OUT5

/GRIDL

POW
OUT

Grid bias voltage control

"H: HIGH,

167

P0OUT6

/BIAS

OUT

Developing bias voltage control

L: Voltage ON

168

P0OUT7

APCSTT

OUT

APC circuit control

H: APC circuit ON

169

PMC0TCLK

MIRCLK

OUT

Mirror motor step count

Mirror motor clock output

170

VCC

171

PMC0DREQB



OUT

(Not used)

172

PMC1TCLK

SPFCLK

OUT

SPF motor step count

173

PMC1DREQB



OUT

(Not used)

174

PMC2TCLK

SFTCLK

OUT

Shifter motor step count

175

PMC2DREQB



OUT

(Not used)

176

TEST

IN

(Not used)

0: Level fixing input

177

TESTB

IN

(Not used)

1: Level fixing input

178

TEST

IN

(Not used)

0: Level fixing input

179

GND

POW

180

GND

POW

181

VCC

POW
Separator motor clock output

POW
SPF motor clock output
Shifter motor clock output

182

PMC3TCLK

LFTCLK

OUT

Separator motor step count

183

PMC3DREQB



OUT

(Not used)

184

PMC4TCLK



OUT

(Not used)

185

PMC4DREQB



OUT

(Not used)

186

DREQ0B

/DREQ0

OUT

"Mirror,SPF motor acceleration/reduction control"

187

DREQ1B

/DREQ1

OUT

"Shifter,separator motor acceleration/reduction L:Request
control"

188

A16

A16

189

VCC

IN

L:Request

System bus

POW

190

CS1B

/CS1

IN

System bus

0: Select

191

CSOUT10B

/CS10

OUT

System bus

L: Select

192

CSOUT11B

/CS11

OUT

System bus

L: Select

193

CS3B

/CS3

IN

System bus

0: Select

194

RDB

/RD

IN

System bus

0: Read

195

HWRB

/HWR

IN

System bus

0: Highlight

196

LWRB

/LWR

IN

System bus

0: Row write

197

GND

198

A1

POW
A1

IN

System bus

Pin descriptions) IN: Input pin OUT: Output pin BIDIR: Bi-directional pin ODN: Open drain output pin TR1: 3-state output pin POW: Power pin
AL-1611/AL-1622

ELECTRICAL SECTION

13 – 12

Pin No.

Pin name

Signal name

199

A2

A2

200

GND

POW

201

VCC

POW

202

A3

A3

IN

System bus

203

A4

A4

IN

System bus

204

A5

A5

IN

System bus

205

VCC

206

A6

A6

IN

System bus

207

A7

A7

IN

System bus

208

GND

209

RSTB

210

GND

I/O
IN

Purpose

Descriptions

System bus

POW

POW
/RESET

IN

System reset

0: Reset

POW

211

CLK

212

GND

CPUCLK

IN

System clock

213

D0

D0

BIDIR

System bus

214

D1

D1

BIDIR

System bus

215

D2

D2

BIDIR

System bus

216

GND

217

D3

D3

BIDIR

System bus

218

D4

D4

BIDIR

System bus

219

D5

D5

BIDIR

System bus

220

VCC

POW

221

GND

POW

222

D6

D6

BIDIR

System bus

223

D7

D7

BIDIR

System bus

224

VCC

225

D8

D8

BIDIR

System bus

226

D9

D9

BIDIR

System bus

227

D10

D10

BIDIR

System bus

228

D11

D11

BIDIR

System bus

229

D12

D12

BIDIR

System bus

230

D13

D13

BIDIR

System bus

231

D14

D14

BIDIR

System bus

232

GND

POW

POW

POW

POW

233

D15

D15

BIDIR

System bus

234

PMC1POUT0

SPFDA

OUT

SPF motor phase A drive

H: Drive

235

PMC1POUT1

SPFDB

OUT

SPF motor phase B drive

H: Drive

236

PMC1POUT2

/SPFDA

OUT

SPF motor phase /A drive

H: Drive

237

PMC1POUT3

/SPFDB

OUT

SPF motor phase /B drive

H: Drive

238

DSCLK

DSCLK

ODN

Document size sensor control

239

DSLED0

LED0

OUT

2: Beam document size sensor control

240

VCC

POW

Pin descriptions) IN: Input pin OUT: Output pin BIDIR: Bi-directional pin ODN: Open drain output pin TR1: 3-state output pin POW: Power pin

AL-1611/AL-1622

ELECTRICAL SECTION

13 – 13

E. RESET CIRCUIT
This circuit detects ON/OFF of power to control start/stop of each circuit. The 5V voltage and WTOVF signal of the main PWB is detected by the reset
IC to generate the reset signal.
When the power voltage reaches the specified level, the circuit operations are started. Before the power voltage falls below the specified level, the circuit operations are stopped to prevent against malfunctions.

VCC

5

NJM2103M

4

WDTOVF

1
2
3

C1 1

RES

C2 1

IC2
8 RESET
7 VSA
6 VSB

C3 0.1

VCC

CPU

IC3A
1

3

2

/RESET
NP

C2

74VHC09

F. MAIN MOTOR DRIVE CIRCUIT
The main motor is driven by the MMD signal from ASIC. While the main motor is rotating, the MMD signal is driven to HIGH and passed through IC35
to the control circuit in the main motor to rotate the main motor. The /MMRDY signal is kept HIGH until the main motor speed reaches the specified
rpm, and passed to the CPU.
96 MMD

IC1
CPU

97 /MMRDY#

IC31
Driver

4

18

14
2

/MMD
/MMRDY

MM

IC32

G. MIRROR MOTOR CIRCUIT
The mirror motor is a stepping motor, and it uses the IC29 and the constant current chopper control IC (SLA7027). For control, the CPU outputs the
drive signal to the IC29 to drive the mirror motor with 1-2 phase excitement.
24V

F6
+

2.4K

2200p

510

47K

RSA
GA
OUTA
OUTA
VSA
VSB
OUTB
OUTB
GB
RSB
SLA7027MU

3 REFA
4 INA
5 INA
2 TDA
13 TDB
16 INB
17 INB
14 REFB

70 MMCC01 1
71 MMCC12 2

620

100

620

2.4K

2200p

MIRMODA
/MIRMODA
MIRMODB
/MIRMODB
4
3
2
1

28
30
29
31

16 /MMRMO1
15 /MMRMO0

5
6
7
8

IC5
ASIC

IC31

470p

470p

+

22 /16V

47K

IC25

AL-1611/AL-1622

ELECTRICAL SECTION

13 – 14

9
4
1
8
7
12
18
11
15
10

1.0(2W)

1.0(2W)

47 /35V

VCC

ICPN38

MMA
/MMA
MMB
/MMB

MIRROR
MOTOR

H. TONER SUPPLY MOTOR DRIVE CIRCUIT
The IC31 is the motor control IC, which generates the pseudo AC waveform with the pulse signals (TM, TM-) outputted from ASIC, driving the toner
supply motor.
1SS133
24V
DTC114EKA
47K(1/4W)

VCC

47K 47K

10µ/16V

+

IC13
Image
ASIC

/PWOFF

6
7

10 /25V
+

TM
/TM

2
9
1
4

229 TM
228 /TM

IC27
VCC
V5
IN1 OUT1
IN2 OUT2
GND
Vref
GND
TA7291S 76/

4.7K(1/4W)

3
8
5

TMD
/TMD

TM

10K

PWOFF

DTC114EKA

1SS133

IC1 CPU

4.7K(1/4W)

10K

3. CCD PWB
The CCD PWB is provided with the CCD (Charge-Coupled Device), the differential amplifier which amplifies image signals, and the AD convertor
which converts the amplified image signals into digital signals.
The DC power and the pulse supply pins necessary for operating the CCD image sensor are the power source (CD pin), GND (SS pin), shift pulse
(SH pin), transfer pulse (φ 1 pin), (φ 2 pin), reset pulse (/RS pin), clamp pulse (/CP pin), and sampling (/SP pin).
Photo data are stored in the light receiving element at the center of the CCD by the SH signal. Even number pixel data are sent to one of the two shift
registers which are positioned at both ends of the light receiving element, and odd number pixel data are sent to the other shift register. The time
interval between inputting two SH signals is called the photo accumulation time.
The signals are transfered to the register, then to the shift register sequentially by transfer pulses φ 1 and φ 2 and to the floating capacitor section
where electric signals are voltage-converted. Electric charges from the even number pixel shift register and the odd number pixel shift register are
flowed to the floating capacitor section alternatively.
12V
CCD analog shift register 1
Photo diode
Output
CCD analog shift register 2

The /RS signal is the reset signal of the CCD output signal. The CCD output is expressed as electric charges equivalently accumulated in the capacitor. Therefore, to take the CCD output data one pixel by one pixel, one output data must be cleared after it is outputted. The /RS signal is used for
that operation.
Photo energy
Shift electrode
To Shift register
Photo diode

Accumulation electrode

The /SP pulse signal is the peak hold signal of the signal voltage.
The output signal from the CCD is amplified by about 4.7 times greater in the differential amplifier circuit in the CCD PWB.
Differential amplification is made for the signal output (OS) and the compensation output (DOS).
The amplified CCD signal output is sent to the clamp circuit. In the clamp circuit, the black level is clamped to 2V at the BCLK signal timing by the
analog switch. The clamped voltage is maintained for one line by the coupling capacitor. The clamped analog signal is impedance-converted and
inputted to the AD convertor.
The analog signal inputted to the AD convertor is converted into 8bit digital data and passed to the PCU PWB.
The machine employs the TCD1501C as the image sensor. The TCD1501C is the reduction type high sensitivity CCD linear sensor of one-output
system. 5000 pixels of 7um x 7um are arranged in line to allow scanning of A3 document at 400dpi (16 lines/mm).
AL-1611/AL-1622

ELECTRICAL SECTION

13 – 15

AL-1611/AL-1622

14 – 1

CIRCUIT DIAGRAM

A

B

C

D

7

LGND

LGND

5V2

5V1

GSOL

RSOL

CLH

PSOL

PGND

PGND

15

17

19

21

23

B/

A

A/

24V1

24V1

N.C.

2

3

4

5

6

7

L

H

L

L

H

H

L

L

H

H

L

L

L

H

H

H

H

H

L

H

L

H

L

SELB

L

8

MOTAN

24V

24V

18

20

22

24

L

SPF/ /RSPF

L2

L1

W0

W3

W2

W1

Y

MOTA

16

SELA

MOTBN

14

24V1

GSOL/

1

2

CN004
(PHR-2)

COVER OPEN

MOTB

12

COVER

PAPER

10

LGND

8

SELC

4

6

SELB

2

LGND

CN001-24

CN002-3

CN005-3

CN002-5

CN002-4

CN001-22

CN002-1

CN001-23

CN002-21

7

CN002
(PHDR-22VS)

CN004
(PHR-2)

5V2

LGND

LGND

L2

L1

W1

W3

W2

W0

LEDSPPD

5V2

3

2

1

LED POWER

LGND

COVER OPEN

CN005
(PHR-3)

21

19

17

15

13

11

9

7

5

3

1

CN002
(PHDR-22VS)

CN003
(PHR-7)

CN005-2

CN002-22

CN001-21

CN002-20

CN002-19

LEDSPPD
R004 220J(1/4W)
C018
LED POWER
10uF/16V

+

TO 5V1

C002
10uF/16V

SELC

Senser
MATRIX

B

1

CN003
(PHR-6)

PDOWN

13

+

11

5V2

5V1

9

LGND

7

Y

3

5

SELA

1

CN001
(PHDR-24VS)

CN001-6

CN001-5

CN001-9

CN001-7

1. INTERFACE PWB

[14] CIRCUIT DIAGRAM

8

CN005
(PHR-3)

5

CN005-1

COVER OPEN

C005
470pF

C006
470pF

R009
47kJ

R003
1.5KJ

R005
9.1KJ

5V1

PDOWN

PSOL
CLH
RSOL
GSOL

C004
0.1uF

5V1

R001
1.5J(1W)

6

PARTS VIEW

LGND

LGND

PAPER

CN001
(PHDR-24VS)

COVER
PAPER
CN001-10
CN001-8

CN001-12

IC001

8

16

4

5V1

C003
100000pF

W1
W2
W3
W0(Document Size Senser)
L1
L2

74HC151AP

CN002-13
CN002-9
CN002-11
CN002-7
CN002-15
CN002-17

CN002-16
CN002-18

C009

R010

C010

R011

C011

R012

C012

R013

C013

R014

3

DSPF

2200pFx6

C014

R015
R016
10kJ

5V1

1.5J(1W)

R002

2.4kJ

R007

2.4kJ

COVER

22

R008
47kJ

CN001-11

CN001-19
CN001-17
CN001-15
CN001-13

3

R006

18

20

CN004-1

CN003-6

CN003-5

CN002-14

CN002-12

CN002-10

4

24V1

24V1

5

24V1

24V1

RSOL/

CLH/

5V2

PSOL/

ICP001

ICP-N38

16

14

12

10

8

6

4

2

PGND

PGND

24V

24V

6

3

9

11
10
9
7

4
3
2
1
15
14
13
12

Y

W

74HC151

A
B
C
G

D0
D1
D2
D3
D4
D5
D6
D7

6

16

17

5

6

5V1

1SS133x3

D007
1SS133

C015 C016

1SS133x3

D006

D001 D002 D003

2

D008
1SS133

1

2200pFx3

C017

1

SELA

SELB

SELC

Y

MOTBN

MOTB

MOTAN

MOTA

B/

A/

A

B

5V1

C001
47uF/35V

11

+

24V1

PSOL/
CLH/
RSOL/
GSOL/

18

1

8

12

D004 D005

5

INB

INB

INA

INA

OUTB

OUTB

OUTA

OUTA

VSB

7

24V1

VSA

9
16
15
14
13
12
11
10

SLA7027M

GB

GA

RSB

REFB

REFA

RSA

TdB

TdA

IC002

IC001

15

4

C008
2200pF
10

14

C007
2200pF

13

COM
O1
I1
O2
I2
O3
I3
O4
I4
I5
O5
I6
O6
I7
O7
GND
BA12003B

2

1
2
3
4
5
6
7
8

IC003

2

CN001-1

CN001-2

CN001-4

CN001-3

CN001-16

CN001-14

CN001-20

CN001-18

CN003-2

CN003-1

CN003-4

CN003-3

CN002-2
CN002-6
CN002-8
CN004-2

1/1

A

B

C

D

AL-1611/AL-1622

14 – 2

CIRCUIT DIAGRAM

A

B

C

D

8

1
2
3
4
5
6
7

W0
5V
W1
W2
W3
COVER
SGND

CN101
(PHR-7)

2. SENSOR PWB

8

7

CN101-7

CN102-2

7

SGND

5V

C101
22000pF

6

6

CN101-6

PT102
GP1S58V

COVER

5

CN101-1

PT101
GP1S58V

W0

R101
120J/ 1/4W

5

4

CN101-3

CN101-4

PT104
GP1S58V

W2

PT103
GP1S58V

W1

R102
120J/ 1/4W

4

3

3

2

CN101-5
PT105
GP1S58V

R103
240J/ 1/4W
W3

2

1

1

1/1

A

B

C

D

AL-1611/AL-1622

15 – 1

ACTUAL WIRING DIAGRAM

1. ACTUAL WIRING DIAGRAM 1/4

[15] ACTUAL WIRING DIAGRAM

2. ACTUAL WIRING DIAGRAM 2/4

AL-1611/AL-1622

ACTUAL WIRING DIAGRAM

15 – 2

3. ACTUAL WIRING DIAGRAM 3/4

AL-1611/AL-1622

ACTUAL WIRING DIAGRAM

15 – 3

AL-1611/AL-1622

15 – 4

ACTUAL WIRING DIAGRAM

PPC

FG

24V
24V
PSOL
GSOL
RSOL
CLH
MOTA
MOTB
MOTAN
MOTBN
PGND
PGND
LGND
LGND
PAPER
COVER
PDOWN
COVER OPEN
Y
SELA
SELB
SELC
5V1
5V2
N.C.

RD
RD
PL
PL
PL
BR
PK
BR
BL
PL
GY
GY
GY
GY
LB
BL
BR
BR
PL
LB
BL
BR
OR
OR

COVER OPEN

GP1A71A1

SRA-21T-4

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25

CL211-0211-6

DF3-3S-2C

2
1
3

FG

EARTH
PLATE

SPF FIXING
PLATE

INTERNAL SPF/DSPF

4. ACTUAL WIRING DIAGRAM 4/4

BR
GY
OR
1
2
3

COVER OPEN
LGND
5V2

CN005
(PHR-3)

CN001
(PHDR-24VS)
24V
22
24
24V
PSOL
19
13
GSOL
15
RSOL
17
CLH
18
MOTA
14
MOTB
MOTAN
20
16
MOTBN
PGND
21
PGND
23
LGND
5
LGND
6
PAPER
8
10
COVER
11
PDOWN
COVER OPEN
12
3
Y
SELA
1
2
SELB
4
SELC
7
5V1
9
5V2

Interface PWB

21
17
3
20
15
4

LGND
L2
5V2
LGND
L1
5V2

1
2

CN004
(PHR-2)
24V1
GSOL/

B
B/
A
A/
24V1
24V1
N.C.

1
2
3
4
5
6
7

14
8

24V1
RSOL/

CN003
(PHR-7)

12
6

24V1
CLH/

5
22
18

10
2

24V1
PSOL/

LEDSPPD
LGND
PAPER

1
7
16
13
9
11
19

5V2
W0
COVER
W1
W2
W3
LGND

CN002
(PHDR-22VS)

PL
PK
BL
LB
RD
RD

RD
PL

4
6
3
1
2
5

MOT

SMP-02V(N)
SMR-02V(N)
1 24V1
2 RSOL/

RD
PK

SMR-02V(B)
24V1
CLH/

BU6P-TR-P-H
GY
1 LGND
6
BL
2 L2
5
OR
4
3 5V
GY
4 LGND
3
LB
2
5 L1
OR
6 5V
1
PHNR-6-H
PHNR-6-H

SMP-02V(B)
1
2

PHR-6

PHNR-7-H

OR
BL
PK
PL
BR
LB
GY

BU2P-TR-P-H
2
1 24V1
2 PSOL/
1
PHNR-2-H
PHNR-2-H

PHNR-7-H

2
1
6
3
4
5
7

RD
LB

PL
GY
BR

GY
BL
OR
GY
LB
OR

RD
BL

OR
BL
PK
PL
BR
LB
GY

BU7P-TR-P-H
6 5V
7 W0
2 COVER
5 W1
4 W2
3 W3
1 LGND

PHR-3
1
2
3

Senser PWB

RSPF ONLY

GSOL

RSOL

CLH

PAPER

Original Tray

L1

L2

PSOL

5V
W0
COVER
W1
W2
W3
LGND

(PHR-7)

1
2
3
DF3-3S-2C
1
2
3
DF3-3S-2C

2
1
6
3
4
5
7

CN101

PAPER FEED UNIT

LGND

5V1

5V2

6

8

10

LGND

PAPER

COVER

RSOL

CLH

PSOL

PGND

PGND

16

18

20

22

24

MOTBN

MOTA

MOTAN

24V

24V

21

5

2
3

LGND
LED POWER

1

2

3

4

6

7

1

2

1

3

5

7

9

11

13

15

19
17

1

23

21

19

17

15

13

11

9

7

5

3

1

COVER OPEN

CN005
(PHR-3)

GSOL

14

MOTB

PDOWN

Y

4

SELC

COVER OPEN 12

SELA

2

SELB

CN001
(PHDR-24VS)

16
14
12
10
8
6
4
2

L1
W1
W3
W2
W0
LEDSPPD
5V2
5V2

B

B/

A

A/

24V1

24V1

N.C.

24V1

CN003
(PHR-6)

CN004
(PHR-2)

20
18

LGND
L2

GSOL/

22

LGND

CN002
(PHDR-22VS)

PSOL/

5V2

CLH/

RSOL/

24V1

24V1

24V1

COVER

LGND
PAPER

LGND

[16] SPF PARTS ARRANGEMENT
[PARTS SURFACE]

[SOLDER SURFACE]

AL-1611/AL-1622

SPF PARTS ARRANGEMENT

16 – 1

q

PARTS GUIDE
DIGITAL COPIER

AL-1611
MODEL AL-1622
CONTENTS

1
2
3
4
5
6
7
8
9
F
G
H
I
J
K
L
M

Exteriors
Operation panel section
Side door unit
2nd,3rd mirror unit
Optical unit
Middle frame unit
Fusing unit
Main driving unit
Base plate unit 1
Base plate unit 2
Manual paper feeding multi unit
Delivery frame unit
TC case unit
250 sheets tray unit
Packing material & Accessories

1ST Tray exteriors (AL-1622)
1ST Tray paper feeding unit
!!!!!(AL1622)

N!MCU PWB
O COPY-Operation PWB
P Duplex/P-out sensor PWB
Q MHPS PWB
R Tray sensor PWB
S Manual paper feeding sensor PWB
T PS sensor PWB
U RCU PWB
V Low voltage power supply unit
W ERDH OP PWB
X 1ST Tray interface PWB (AL-1622)
Y SPF Exteriors (AL-1622)
Z SPF Pick up unit (AL-1622)
[ SPF Transport unit (AL-1622)
\ SPF interface PWB (AL-1622)
] SPF sensor PWB (AL-1622)
!!!
■!!Index

Because parts marked with "!" is indispensable for the machine safety maintenance and poeration, it must
Be replaced with the parts specific to the product specification.

SHARP CORPORATION

This document has been published to be used for
after sales service only.
The contents are subject to change without notice.

DEFINITION
The definition of each Rank is as follows and also noted in the list
A: Maintenance parts, and consumable parts which are not included in but closely related to maintenance parts.
B: Performance/function parts (sensors, clutches, and other electrical parts), consumable parts.
E: Unit parts including PWB.
D: Preparation parts (External fitting, packing, parts packed together).
C: Parts other than the above (excluding sub components of PWB).
Because parts marked with "!" is indispensable for the machine safety maintenance and operation, it must be replaced with
the parts specific to the product specification.
F Other than this Parts Guide, please refer to documents Service Manual(including Circuit Diagram)of this model.
F Please use the 13 digit code described in the right hand corner of front cover of the document, when you place an order.
F For U.S. only-Use order codes provided in advertising literature. Do not order from parts department.

1 Exteriors
NO.
1
2
3
4
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
26
28
29
38
41
44
46
49
50
51
52
53
54
56
57
501

PARTS CODE
GCOVH0010QSZ4
PSHEZ0058QSZ1
CHNG-0007QS01
XEBSE40P10000
GFTA-0002QSZZ
CFIX-0008QS02
PGLSP0003QSZZ
PSHEZ0059QSZZ
CCAB-0012QS1G
CCAB-0012QS1H
GFTA-0001QSZZ
CARMP0010QS01
CARMP0011QS01
XEBSE40P10000
GCAB-0014QSZZ
XBBSE30P06000
XHBSE30P08000
GCAB-0013QSZ1
PGIDM0054QSZ1
XHBSD30P06000
PGIDM0055QSZZ
GCOVH0011QSZZ
GCOVH0013QSZ1
GCAB-0015QSZZ
XEBSE40P10000
XEPSD30P08X00
PSHEZ0089QSZZ
PCAPH0011QSZZ
XHPSD30P08X00
PMLT-0032QSZZ
TLABH0388QSZ1
TCAUA0770FCZZ
TLABZ0058QSZZ
PCUSS0011QSZZ
PGLSP0004QSZZ
PSHEZ0122QSZ2
PTPE-0010QSZZ
PTPE-0015QSZZ
PSHEZ0124QSZ1
PSHEZ0123QSZ2
CCOVH0010RS51

PRICE NEW
RANK MARK
BC
AU
AM
AA
AD
AQ
BA
AF
BB
BB
AW
AD
AD
AA
AY
AA
AA
BA
AG
AA
AG
AP
AL
AV
AA
AA
AF
AC
AA
AC
AG
AB
AD
AB
AX
AB
AC
AC
AB
AA
BG

PART
RANK
D
C
C
C
D
D
B
C
D
D
D
C
C
C
D
C
C
D
C
C
C
D
D
D
C
C
C
C
C
C
D
D
D
C
B
C
C
C
C
C
E

DESCRIPTION
OC cover
OC sheet
OC hinge
Screw(4×10)
SPF connector cover
Glass fixing plate
Table glass
Sheet
Front cabinet
Front cabinet
Front cabinet cover
Hinge arm L
Hinge arm R
Screw(4×10)
Left cabinet
Screw(3×6)
Screw(3×8)
Rear cabinet
Hinge guide L
Screw(3×6)
Hinge guide R
OC glass fixing cover
SPF glass fixing cover
Right cabinet
Screw(4×10)
Screw(3×8X)
Table glass sheet R
SC cap
Screw(3×8X)
OC cushion
Operation label
Service caution label
Class 1 label
SPF glass custhion
SPF slit glass
White revision sheet
Slit glass tape
SPF glass fixing tape
SPF glass sheet R
SPF glass sheet F
OC cover unit

–1–

(AL-1611)
(AL-1611)
(AL-1611)
(AL-1611)

(AL-1611)
(AL-1622)

(AL-1611)
(AL-1622)

(AL-1611)

(AL-1622)
(AL-1622)
(AL-1622)
(AL-1622)
(AL-1622)
(AL-1622)
(AL-1622)
(AL-1611)

1 Exteriors

501

1

20

3

16

4
19
3
16
44

7

4

41

16

16

21

2

9

6

16
29
46

16

16

17

20

8

56

16

49
14

16
52

57 53

17

22

28

16

54

14
14
17

16
17

51 50

18

16

50

15

16

16
16

17
17
17
26

24
12

23

24
38

26 24
26

10
13

11

17

17

24

FCP05885
24

–2–

50

2 Operation panel section
NO.
1
2
3

4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
28
29
31
32
33
34

PARTS CODE
GCOVH0015QSZZ
GCOVH0016QSZZ
HPNLH0024QSZ3
HPNLH0024QSZ2
HPNLH0024QSZ5
HPNLH0024QSZ4
HPNLH0022QSZ4
HPNLH0022QSZ3
GCAB-0017QSZ1
JBTN-0018QSZZ
JBTN-0029QSZZ
CBTN-0022QS01
CBTN-0021QS01
CBTN-0019QS02
JBTN-0020QSZZ
CBTN-0016QS01
JBTN-0026QSZZ
JBTN-0030QSZZ
JBTN-0027QSZZ
JBTN-0023QSZZ
CPWBF0025QSE3
XEBSD30P08000
CPWBF0024QSE7
DHAI-0116QSZZ
DHAI-0115QSZZ
DHAI-0149QSZZ
PSHEZ0137QSZZ
PSHEZ0131QSZZ
PCUSG0018QSZZ
PCUSG0019QSZZ
RCORF0005QSZZ
PSHEZ0399QSZZ

PRICE NEW
RANK MARK
AG
AH
AT
AT
AT
AT
AK
AK
AV
AE
AE
AF
AF
AF
AC
AN
AE
AD
AD
AG
AH
AA
BH
N
AC
AF
AE
AH
AG
AD
AC
AH
AB

PART
RANK
D
D
D
D
D
D
D
D
D
C
C
C
C
C
C
C
C
C
C
C
E
C
E
C
C
C
C
C
C
C
C
C

DESCRIPTION
LCD dummy cover
FAX dummy cover
Main Deco.panel
Main Deco.panel
Main Deco.panel
Main Deco.panel
DUP Deco.panel
DUP Deco.panel
Operation panel cabinet
Function key
Select key
CA key
Clear key
Copy key
Copy key (LIGHT IND)
Ten key
Interrupt key
Mode select key
Density select key
Special function key
ERDH operation PWB
Screw(3×8)
COPY operation PWB
Panel ERDH harness
Operation panel harness
OP. earth harness
OP mylar sheet
OP shield sheet
Rubber cushion(T8)
Rubber cushion(T4S)
Ferrite core
OP-PWB protect sheet

2 Operation panel section

(AL-1611 U.Kingdom)
(AL-1611 Germany)
(AL-1622 U.Kingdom)
(AL-1622 Germany)
(U.Kingdom)
(Germany)

2
1

3

5

4

18
12

13
15
21

14

19
6

8

10
9
11
7

16

20
34

18

17
18
18
18

18
18

31

31

32

28
29
18

18

22

18

33

–3–

FCP05886

3 Side door unit
NO.
1
2
3
4
5
6
7
8
9
10
11
13
14
15
16
18
20

PARTS CODE
GDOR-0001QSZZ
LRALP0004QSZ1
XHBSD30P10000
LPLTM0092QSZZ
XHBSD30P14000
LPLTM0091QSZZ
XEBSD30P10000
LPLTM0090QSZZ
MSPRC0085QSZZ
LFRM-0016QSZ3
XHBSD30P16000
MSPRC0084QSZ1
MSPRC0083QSZ1
LHLDZ0033QSZ1
MSPRC0082QSZ1
CHLDZ0030RS51
TLABH0124QSZZ

PRICE NEW
RANK MARK
AW
AH
AA
AF
AA
AE
AA
AE
AE
AQ
AA
AD
AD
AF
AC
BA
AC

PART
RANK
D
C
C
C
C
C
C
C
C
C
C
C
C
C
C
E
D

DESCRIPTION
Right door
Right door rail
Screw(3×10)
Rail reinforce plate
Screw(3×14)
Inner reinforce plate R
Screw(3×10)
Inner reinforce plate F
TC case GND spring
Right door inner N
Screw(3×16)
BC I/F spring
TC I/F spring
TC terminal I/F holder
Pressure spring
TC unit
Green label

3 Side door unit

13

7

14
15
18

11

7

3
16

10
3

16

7
3 2

7

5
1

3
6

7

11
3

3

9

4

5
8

20
2
4
FCP05887

–4–

4 2nd,3rd mirror unit
NO.

PARTS CODE

LHLDZ0044QSZZ
XBPSD40P06KS0
NPLYZ0017QSZZ
LHLDZ0013QSZZ
XEBSD40P06000
MSLI-0138FCZZ
LX-BZ0335FCZZ
CPLTM0156QS02
PCUSS0009QSZZ
LFIX-0284FCZZ
PMIR-0008QSZZ
CPLTM0155QS02
PCUSS0201FCZZ
PSPAZ0011QSZZ
(Unit)
901 C M I R - 0 0 0 8 Q S 3 2
1
3
4
5
6
7
8
9
10
11
12
13
14
15

PRICE NEW
RANK MARK
AP
AA
AE
AD
AA
AC
AA
AH
AA
AC
AP
AH
AA
AD

PART
RANK
C
C
C
C
C
E
C
C
C
C
B
C
C
C

BB

E

DESCRIPTION
2nd,3rd mirror holder
Screw(4×6KS)
W pulley
CL guide holder
Screw(4×6)
Slider
Screw(4×6)(Red)
Pulley fixing plate R
MB-B cushion R
2nd,3rd mirror fixing plate F
2nd,3rd mirror
Pulley fixing plate F
MB-B cushion
Mirror spacer
2nd,3rd mirror unit

4 2nd,3rd mirror unit

5

4

6
8

8
15
1

3

3

4

9

7

7
10
11

6
12
8

11

7

8 13

5 Optical unit
NO.
1
2
4
5
6
7
8
9
12
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39

PARTS CODE
PWIR-0005QSZ1
CMIR-0008QS32
LHLDZ0056QSZZ
XBPSD40P06K00
XHBSD30P06000
PCASZ0008QSZZ
CLNS-0003RS53
DHAI-0120QSZZ
PWIR-0006QSZZ
NPLYZ0016QSZZ
NPLYZ0006QSZZ
XRESP40-05000
PGUMS0004QSZZ
CPWBF1177DS63
XBBSD30P08000
LBNDJ0043FCZ1
LHLDZ0043QSZZ
LX-BZ0004QSZZ
LRALM0007QSZZ
MSPRC0040QSZZ
XBPSD30P05K00
RMOTP0021QSZ1
XBPSD40P16KS0
CPLTM0084QS01
PGUMS0002QSZZ
NGERH0027QSZZ
LX-WZ0119FCZZ
XRESP70-08000
NBLTT0002QSZZ
XRESP50-06000
NBRGC0387FCZ1

11

PART
RANK
C
E
C
C
C
C
E
C
C
C
C
C
C
E
C
C
C
C
C
C
C
B
C
C
C
C
C
C
B
C
C

12

FCP05888

14
PRICE NEW
RANK MARK
AQ
BB
AC
AA
AA
AM
BR
AG
AQ
AF
AD
AA
AA
AR
AA
AA
AE
AB
AG
AB
AA
BC
AA
AL
AL
AH
AA
AA
AH
AA
AC

11

DESCRIPTION
MB wire R
2nd,3rd mirror unit
Wire holder
Screw(4×6K)
Screw(3×6)
Dark box
Lens unit
CCD harness
MB wire F
Pulley
L pulley
E type ring
Table glass cushion
MHPS PWB
Screw(3×8)
Band(SG-130)
CL lead holder
Screw(3×63)(Red)
MB-B rail R
MB drive spring
Screw(3×5K)
Mirror motor
Screw(4×16KS)
Mirror motor fixing plate
Protection rubber
Mirror motor idle gear
Washer
E type ring
Winder drive belt
E type ring
Bearing

–5–

5 Optical unit
NO.

!

40
41
42
43
44
45
46
47
48
51
52
53
54
55
56
57
58
59
63
68
71
72
79
81
82
83
84
85
86
87
88
89
90
91
93
94
95
501

PARTS CODE
NPLYZ0004QSZZ
LX-BZ0324FCZZ
LX-BZ0049FCZZ
NPLYZ0013QSZZ
NSFTZ0028QSZZ
XPSSJ30-12000
NBRGC0133FCZ1
LRALM0006QSZZ
CDAIU0012QS06
PSHEP0085QSZZ
PSHEZ0108QSZZ
PSHEZ0109QSZZ
XHBSD30P04000
LX-BZ0004QSZZ
PMLT-0033QSZZ
PMLT-0034QSZZ
PSHEZ0152QSZZ
RCORF0002QSZZ
PMLT-0035QSZZ
LHLDZ7021XCZZ
PSHEZ0160QSZZ
PSPAZ0018QSZZ
RCORF0002QSZZ
DHAI-0200QSZZ
DUNTK0034QSZZ
LFIX-0009QSZZ
LHLDZ0047QSZ2
MSLI-0138FCZZ
MSPRP0145QSZZ
PCUSF0334FCZZ
PCUSU0203FCZZ
PMIR-0009QSZZ
PREFL0004QSZZ
RLMPU0012QSZZ
XEBSD30P06000
XEBSD30P08000
XEBSD40P06000
CREFL0004QS33

PRICE NEW
RANK MARK
AG
AA
AB
AL
AM
AB
AC
AG
BL
AC
AC
AC
AA
AB
AC
AC
AD
AE
AB
AD
AE
AE
AE
AS
BC
AF
AW
AC
AF
AP
AE
AS
AP
BG
AA
AA
AA
BL

PART
RANK
C
C
C
C
C
C
C
C
D
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
E
C
C
E
C
C
C
B
C
B
C
C
C
E

DESCRIPTION
Winder drive shaft pulley
Screw(3×4)
Screw(4×6)
Winder pulley
Winder drive shaft
Spring pin(φ3-12)
PF bearing(M8)
MB-B rail F
Optical base plate
Optical edge protect sheet D
Optical base plate bottom myler A
Optical base plate bottom myler B
Screw(3×4)
Screw(3×63)(Red)
Optical cushion D
Optical cushion E
Optical bottom sheet
Ferrite core(HF57SH35*1)
Core holding cushion
Holder(FRH-12)
Dark box lower sheet
Cable fixing spacer
Ferrite core(HF57SH35*1)
CL harness
Inverter unit
Harness fixer
Base plate
Slider
Mirror spring
Mirror cushion
Cushion
1st mirror
Reflector
Lamp
Screw(3×6)
Screw(3×8)
Screw(4×6)
Copy lamp unit

5 Optical unit

93

95

90

1

85
93
91
5
84

4
2

5
4

88

501

6
12

85

94
89 86
93

95

6

88

6

82
87

85

9

55

93

7

18

19

20

23

22

8
79
59

9
26
54

20

19

6

28

6
68

21

18

86

31

25

29

30

32
68

24

24
21

21

59

33 24

72

26

54

33

35
27

24 31

37

34
21

21

21

36
51

47

63

38
39

41
53 45

26
48
21
71

57

43

52

40

53
42
53
56

53

46

52
41

36

44
58

43

FCP05889
42

–6–

93

93

81
83
93

6 Middle frame unit
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
18
21
22
23
24
25
26
27
28
29
30
31
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
49
50
52
53
54
55
56
57
58
59

PARTS CODE
XEPSD23P12000
CSW-M0007RS51
NCPL-0002QSZZ
MSPRC0024QSZZ
RMOTD0016QSZ1
XEBSD30P10000
DUNTK0041RS14
DHAI-0141QSZZ
XBPSC30P06ES0
CHAI-0109RS51
CHAI-0107RS51
MSPRD0104QSZZ
MSPRD0103QSZZ
MSPRD0102QSZZ
LHLDZ0038QSC1
XEBSD30P08000
XEBSD30P10000
LHLDZ0039QSZZ
LPLTM0067QSZZ
XEBSD30P06000
DHAI-0106QSZZ
DHAI-0108QSZZ
MSPRC0105QSZ1
XRESP40-06000
NSFTZ0021QSZ1
NKOM-0001QSZZ
MSPRD0139QSZZ
XEBSD30P06000
LBOSZ1508FCZZ
PPIPP0174FCZZ
MSPRC0106QSZZ
XPSSJ20-07000
NGERH0062QSZZ
NBRGC0018QSZZ
XRESP60-08000
NROLP0032QSZ2
JKNBZ0003QSZZ
XBPSD30P10KS0
LPLTM0070QSZZ
QSW-B0003QSZZ
DHAI-0090QSZZ
LFRM-0024QSZ3
LPINS0007QSZZ
PSHEZ0056QSZZ
PTPE-0017QSZZ
XHBSD30P06000
TCAUH0007QSZZ
LBNDJ0013FCZ1
LPLTM0302QSZZ
LX-BZ0020QSZZ
DHAI-0254QSZZ
XBBSD30P06000
MSPRP0299QSZZ

PRICE NEW
RANK MARK
AA
AQ
AC
AA
AZ
AA
BG
AP
AA
AN
AG
AC
AC
AC
AH
AA
AA
AE
AC
AA
AL
AK
AB
AA
AL
AD
AB
AA
AG
AC
AF
AA
AK
AD
AA
AT
AD
AB
AD
AF
AF
BC
AC
AC
AA
AA
AD
AA
AC
AB
AP
AA
AC
N

PART
RANK
C
E
C
C
B
C
E
C
C
E
E
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
C
C
C
C
C
C
D
C
C
C
C
C
C

DESCRIPTION
Screw(2.3×12)
Inter lock switch unit
Hopper coupling
Hopper spring
Toner motor
Screw(3×10)
LSU unit
DEV harness
Screw(3×6ES)
GB-MCFB harness unit
MC harness unit
HV terminal spring (case)
HV terminal spring (grid)
HV terminal spring
High voltage terminal holder
Screw(3×8)
Screw(3×10)
High voltage terminal holder TC
TC terminal plate
Screw(3×6)
BC harness
TC harness
PS pressure spring
E type ring
PS roller shaft
PS collar(φ12)
PS earth spring
Screw(3×6)
Cam boss A2
Pipe C
PS clutch spring
Spring pin(φ2-7)
Clutch gear(32T)
Bearing E
E type ring
PS trnsport roller
PS knob
Screw(3×10KS)
Process detect SW fixing plate
Tray detect switch
Drum initial SW harness
Middle frame
DV guide pin
PS rear guide sheet
FFC tape
Screw(3×6)
Laser caution label
Cable band
CRUM fixing plate
Screw
CRUM connector
Screw(3×6)
CRUM fixing spring

–7–

6 Middle frame unit

6
50
7

6
54
16

55

6

58

53
6

59

18

6
57

11

5
10
3
4

1

18

56
15
16

8 6
9

18
47

6

2

9

12 13

16

14

52

21
26 22

22
25
29

29
49

33

28

36
49

44

38
31 39

23

46

27

30

24
23
26

40

35

34

37

43
6
45

39

42

38
41

–8–

FCP05890

27

7 Fusing unit
NO.

!

PARTS CODE

XBPSD30P05KS0
RTHM-0001QSZZ
DHAI-0184QSZZ
XHBSD30P06000
PCOVP0029QSZ2
RLMPU0016QSZZ
LSTPP0116FCZZ
NBRGP0567FCZZ
XBPSD30P08KS0
CFRM-0017QS01
NROLI0030QSZZ
CFRM-0018QS01
NGERH0540FCZ3
LHLDZ0034QSZZ
XBPSD30P10KS0
RDTCT0005QSZZ
LPLTM0050QSZZ
MSPRT0086QSZZ
PTME-0020GCZ1
PGIDM0034QSZ2
XEBSD30P06000
XBBSD30P06000
LPLTP0051QSZZ
PSHEP0053QSZ4
PGIDH0033QSZ1
NROLR0031QSZ1
NBRGP0260FCZ1
XRESP30-06000
LX-BZ0013QSZ1
MSPRP0087QSZZ
MSPRT0089QSZ2
MLEVP0018QSZ1
MLEVP0019QSZ3
MLEVP0020QSZ3
MLEVP0017QSZ1
PTME-0020GCZ1
TLABH0062QSZZ
LFRM-0036QSZZ
LPLTP0060QSZ3
MLEVP0026QSZ2
MSPRD0117QSZZ
MSPRD0118QSZ1
PSHEZ0105QSZZ
LX-WZ0313FCZZ
VRH-ST2HB157K
PBRSR0004QSZ1
PTME-0014QSZZ
MSPRD0122QSZZ
MSPRD0121QSZZ
XWHSD30-05070
LX-WZ0001QSZZ
PSHEZ0238QSZZ
CPLTP0060RS52
(Unit)
901 D U N T W 0 0 3 7 R S 2 4
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
27
28
29
30
31
32
33
34
35
36
37
39
40
41
42
43
44
46
48
49
50
51
52
53
54
55
56
501

PRICE NEW
RANK MARK
AA
AM
AF
AA
AT
BA
AA
AG
AA
AH
BC
AH
AD
AF
AB
AN
AM
AB
AF
AL
AA
AA
AD
AH
AK
BC
AD
AA
AC
AC
AC
AF
AE
AE
AF
AF
AE
AT
AM
AE
AB
AB
AC
AA
AD
AD
AK
AB
AB
AA
AC
AC
BU
BV

PART
RANK
C
B
C
C
C
B
C
C
C
C
C
C
C
C
C
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
D
D
C
C
C
C
C
C
C
C
C
C
C
C
C
C
E
E

DESCRIPTION
Screw(3×5KS)
Thermostat
Fusing harness
Screw(3×6)
Fusing cover
Heater lamp(230V)
Roller stopper
Fusing bearing
Screw(3×8KS)
Fusing frame F
Upper heat roller
Fusing frame R
Fusing gear(45T)
Lamp holder
Screw(3×10KS)
Thermistor
Fusing joint plate
Upper pawl pressure spring
Separator pawl
Fusing rear paper guide
Screw(3×6)
Screw(3×6)
PG fixing plate
PG sheet
Fusing front paper guide
Pressure roller
Pressure bearing N
E type ring
Screw(3×7)
PG earth spring
Pressure spring B
Fusing pressure lever F
Release lever F
Release lever R
Fusing pressure lever R
Separator pawl
High temperature caution label
Fusing lower frame
Reverse gate
DMC actuator
Rotetion spring
Actuator return spring
Fusing sheet
Washer
Resistor(1/2W 150MΩ±10%)
Discharger brush
Lower separator pawl
Separator pawl spring R
Separator pawl spring F
Washer
Separator pawl washer
Fusing EM sheet
Reverse gate unit
Fusing unit(230V)

–9–

7 Fusing unit

7
13

1
2

8
4

3

B

14

4
12
5

4
6

51

11

49

17

52

46

15
16

4

51
53

8

21

54

4

18

37
55

A

7
10

19
55

4

19

18

55

4

18

55

1

4

50

20

37
18

9
48

46
56

24

27

28
29
30
31

22

B

25
22
40

23

48

32

29

28
39

30

36

A

43

35
32

44

42
34

41

501
33

FCP05891

– 10 –

8 Main driving unit
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
501

PRICE NEW
RANK MARK
AL
AA
AP
AL
AF
AA
BF
AD
AA
AN
AF
AA
AB
AD
AC
AN
AA
BA
AD
AD
AD
AD
AA
AB
AE
AH
AE
AL
AD
AE
AF
AG
AD
AB
AE
AE
AA
AD
AE

PARTS CODE
PGIDM0030QSZZ
XHBSD30P08000
DHAI-0110QSZZ
DHAI-0089QSZ1
DHAI-0309QSZZ
XBBSD40P10000
RMOTP0039QSZZ
PTME-0003QSZ1
MSPRC1318FCZ1
RPLU-0009QSZZ
LPLTM0048QSZZ
XRESP40-06000
LX-WZ0002QSZZ
NGERH0053QSZZ
PTME-0012QSZZ
RPLU-0008QSZZ
XBBSD30P04000
CPLTM0047QS02
NGERH0010QSZZ
NGERH0009QSZZ
NGERH0014QSZZ
NGERH0011QSZZ
MSPRC2132FCZ1
NCPL-0004FCZZ
NGERH0052QSZZ
NGERH0007QSZZ
NGERH0057QSZZ
NGERH0008QSZ3
NGERH0059QSZZ
NGERH0012QSZZ
NGERH0058QSZZ
NGERH0013QSZZ
NGERH0016QSZZ
MSPRC0081QSZZ
NGERH0055QSZZ
NGERH0056QSZZ
LX-WZ0314FCZZ
NGERH0054QSZZ
CGERH0011RS51

PART
RANK
C
C
C
C
C
C
B
C
C
B
C
C
C
C
C
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
E

DESCRIPTION
Harness guide
Screw(3×8)
HL harness
Thermistror harness
Main motor harness
Screw(4×10)
Main motor
Roller pawl
Spring B
Solenoid CSA
Drive earth plate
E type ring
PO belt washer
Gear(25/18T)
PS clutch pawl
Solenoid PS
Screw(3×4)
Main drive plate
Gear(28T)
Gear(46/16T)
Gear(30/15T)
MG gear
MG roller spring
Coupling B
Gear(38/18T)
Gear(68/26T)
Gear(41T)
Gear(55/19T)
Gear(23/27T)
Gear(20T)
Gear(21/17T)
Gear(31/17T)
Coupling gear(34T)
HT ratchet spring
Ratchet gear(44T)
Ratchet gear(33T)
Washer
Gear(33/20T)
MG gear unit

8 Main driving unit
5

1

2

6

3
2

7

8

6

2

9

20

19

4

10

18

11
12
13

21
15

22
23

16

17

25

501

26

24

33
28

27

14
9

17
34
35

31
29

32
30
30

19

12
19

37

36

38

– 11 –

FCP05892

9 Base plate unit 1
NO.
1
2
3
4
5
6
7
11
12
13
14
15
16
17
18
19
20
22
23
24
25
26
27
28
29
30
31
32
33
34
35
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
54
55

PARTS CODE
QSW-B0003QSZZ
DHAI-0091QSZ1
PTME-0013QSZZ
MSPRT0100QSZZ
MLEVP0022QSZ1
LPLTM0065QSZZ
XEPSD40P12000
XEBSD30P08000
GDAI-0002QSZZ
XRESP40-06000
LBOSZ1031FCZZ
MSPRC0161QSZZ
PPIPP0006QSZZ
NGERH0060QSZZ
XRESP50-06000
NBRGP0007QSZZ
CSFTZ0066RS71
XEBSD40P12000
PSHEZ0133QSZZ
CPWBF1177DS66
MLEVP0023QSZZ
PCOVP0033QSZZ
LRALP0005QSZ1
PSHEZ2026FCZZ
LHLDZ0017QSZZ
MSPRC0101QSZ1
GFTA-0007QSZZ
MLEVP0024QSZZ
LDAIU0011QSZZ
CPWBF1177DS65
MSPRD0148QSZZ
PCOVP0032QSZ1
MSPRC0099QSZ1
MLEVP0021QSZZ
CPWBF1177DS67
GLEGG0064FCZZ
MLEVP0044QSZZ
XRESP70-08000
NGERH0078QSZZ
NGERH1169FCZZ
CPLTM0114QS01
XEBSE40P12000
LPLTM0112QSZZ
XEBSE40P14000
LPLTM0136QSZZ
LX-BZ0018QSZZ
LPLTM0125QSZZ
PSHEZ0196QSZ1
PSPAZ0024QSZZ

PRICE NEW
RANK MARK
AF
AK
AL
AB
AE
AL
AA
AA
BH
AA
AC
AF
AD
AH
AA
AD
AU
AA
AD
AR
AE
AF
AN
AB
AD
AB
AE
AF
AF
AR
AB
AD
AC
AD
AR
AC
AE
AA
AE
AF
AG
AA
AE
AA
AD
AB
AD
AD
AB

PART
RANK
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
E
C
C
C
C
C
C
C
C
C
E
C
C
C
C
E
C
C
C
C
C
B
C
C
C
C
C
C
C
C

DESCRIPTION
Tray detect switch
Tray SW harness
Door lock pawl
Door lock lever spring
Door lock lever
Base reinforce plate F
Screw(4×12)
Screw(3×8)
Base plate
E type ring
Clutch boss
Clutch spring
Clutch sleeve
Clutch gear(34T)
E type ring
Bearing(φ6)
Paper feeding roller
Screw(4×12)
Paper feeding sheet
Manual paper feeding sensor PWB
MF sensor actuator
Manual feed sensor cover
Base plate rail R
Sheet M1
Pressure plate holder
Pressure plate spring
Pressure plate cover
Sensor lever ACT
Sensor base
Tray sensor PWB
MF sensor spring
PS sensor cover
PS front actuator spring
PS front actuator
PS sensor PWB
Rubber foot
MF sensor actuator 2
E type ring
Joint gear(39/33T)
2ND Joint gear
Joint gear fixing plate
Screw(4×12)
Adjustment plate
Screw(4×14)
2ND joint R front plate
Screw(3×6)
Blind plate
Manual paper guide mylar
2nd joint spacer

(AL-1622)

(AL-1622)
(AL-1622)
(AL-1622)
(AL-1622)
(AL-1622)
(AL-1622)
(AL-1622)
(AL-1622)

(AL-1622)

9 Base plate unit 1
52

41

1
2

49
48

52

3

16 15

12
4

18

14 13

17
55
49

5

48

43

44

46

49

48
23
35
41

54

45

47
42

25
11
24

33
28
11
7
7

6
7

11
32 40
34
38
51
37
50
49

30
39 31

18

29

19

26
11

20
22

11
27
11

– 12 –

22

FCP05893

F Base plate unit 2
NO.

!
!

!
!

!

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
20
21
22
23
24
25
26
27
29
37
38
39
40
42
43
44
46
47
48
49
50
53
54
55
56
57
58
61
62
63
64
65
66
67
78
79
80
96
97
501

PARTS CODE
GCOVH0014QSZZ
GCOVH0012QSZZ
LSOU-0013QSZ1
XEBSE30P08000
XHBSE30P08000
NFANP0003QSZ1
XBPSD30P30KS0
RDENC0009QSZZ
DUNTK0049RS19
XBPSD30P08KS0
RDENC0008QSZZ
LPLTM0082QSZ5
XHBSD30P06000
LFRM-0022QSZZ
XEBSD40P12000
LFRM-0023QSZZ
XBPSN40P06K00
DHAI-0143QSZ1
DHAI-0142QSZ1
LBNDJ2003SCZZ
LFRM-0032QSZ1
GDAI-0002QSZZ
LFRM-0025QSZ2
LPLTM0099QSZ1
LFRM-0026QSZ1
XHBSD30P14000
XEBSD30P10000
XHBSD30P08000
CPWBX0096QSG7
LPLTM0063QSZ1
XBBSE30P06000
LPLTM0064QSZ1
LBNDJ0043FCZ1
CPWBF0033QSE1
DHAI-0101QSZ1
XEBSD30P18000
XWSSD30-07000
XWHSD30-05080
QTANN0015FCZZ
DHAI-0140QSZZ
LFIX-0016FCZZ
XEPSD40P30000
XEBSD40P12000
XWSSD40-10000
XWHSD40-08100
LX-WZ0144FCZZ
PSHEZ0136QSZZ
LPLTM0134QSZZ
XHBSE30P08000
PSHEZ0135QSZZ
XWHSD40-08100
PSHEP0085QSZZ
PSHEZ0109QSZZ
DHAI-0124QSZ2
LX-BZ0019QSZZ
RCORF2037SCZZ
RCORF0006QSZZ
PSHEZ0140QSZZ
DUNTK0050RS31

PRICE NEW
RANK MARK
AR
AS
BA
AA
AA
AY
AA
BK
BH
AA
BN
AF
AA
AP
AA
AQ
AA
AS
AQ
AA
AL
BH
AH
AK
AN
AA
AA
AA
CB
N
AS
AA
AN
AA
AP
AL
AA
AA
AA
AG
AP
AD
AA
AA
AA
AA
AA
AC
AD
AA
AC
AA
AC
AC
AY
AD
AH
AL
AE
CC

PART
RANK
C
C
D
C
C
C
C
E
E
C
E
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
E
C
C
C
C
E
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
E

DESCRIPTION
Delivery left cover
Delivery rear cover
Delivery tray
Screw(3×8)
Screw(3×8)
PS fan
Screw(3×30KS)
Low voltage power supply unit
AC switch unit
Screw(3×8KS)
High voltage power supply unit
PS PWB fixing plate
Screw(3×6)
Corner frame FL
Screw(4×12)
Corner frame RL
Screw(4×6K)
AC cord
AC cord
Wire band
Corner frame CR
Base plate
Corner flame FR
Corner frame R reinforce plate
Corner frame RR
Screw(3×14)
Screw(3×10)
Screw(3×8)
MCU PWB
MCU fixing plate
Screw(3×6)
MCU shield plate
Band(SG-130)
RCU PWB
PS high voltage harness
Screw(3×18)
Washer
Washer
3P terminal base
AC harness
AC cord holder
Screw(4×30)
Screw(4×12)
Washer
Washer
Fusing washer
Motor plate sheet
Corner frame earth plate
Screw(3×8)
Driving plate sheet
Washer
Optical edge protect sheet D
Optical base plate bottom myler B
SPF harness
Screw
Core
Ferrite core
3P terminal base sheet
Power supply unit

– 13 –

(U.Kingdom)
(Germany)
(AL-1622)

(AL-1622)

(AL-1622)
(AL-1622)
(AL-1622)
(AL-1622)

F Base plate unit 2

39
1

39
40

43

2
5

79 66
13

39
39

39
13

79

39
37 44

13

D

4

5

38

A

501

3

9
17

13

80

6
10

10

7

39
61

78

96

13

8
10

58

D
15

10

13

15

15
15

11
18
12
4

4
14

16

4

15

15

20

56
57

54
56

50

55

97
48

57
A
53
42 96
15

21
63
46
25

15
62
22

15

47

49
18

15
65
64
29
13
27

67
24
13
23

15
27

15
15
26

– 14 –

15

FCP05894

G Manual paper feeding multi unit
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
41
42
43
45
46
47
48
51
52
501
502

PARTS CODE
PCOVP0030QSZZ
MARMP0008QSZZ
LPLTP0056QSZ3
XRESP40-06000
LBOSZ1510FCZZ
PPIPP0109FCZZ
MSPRC1315FCZ1
XPSSJ20-07000
LBOSZ1508FCZZ
LBSHZ0303FCZZ
NSFTZ0018QSZ1
MSPRT0091QSZZ
NROLR0922FCZZ
NGERH0495FCZZ
NGERH0061QSZZ
MARMP0009QSZZ
CROLP1115FC01
XEBSD30P08000
MARMP0007QSZZ
MARMP0006QSZZ
NSFTZ0017QSZZ
MCAMP0001QSZZ
MSPRC1316FCZ1
PPIPP0009QSZZ
CPLTM0055QS01
MSPRD0092QSZZ
NGERH0972FCZZ
RPLU-0007QSZZ
MSPRC1318FCZ1
PTME-0179FCZZ
PTME-0178FCZZ
MSPRC2175FCZZ
LFRM-0020QSZZ
XBBSD30P10000
PSHEZ0099QSZZ
MSPRT0147QSZZ
PSHEZ0100QSZZ
PGIDM0037QSZZ
PGIDM0038QSZZ
XEBSE30P08000
LSOU-0009QSZ1
NGERH0193FCZZ
LSOU-0011QSZZ
LSOU-0010QSZZ
MARMP0005QSZZ
XEBSD30P08000
CFRM-0020RS51
CSOU-0009QS32

PRICE NEW
RANK MARK
AN
AH
AD
AA
AF
AB
AD
AA
AG
AC
AL
AC
AR
AC
AD
AF
AN
AA
AE
AD
AG
AF
AE
AD
AF
AE
AB
AN
AA
AC
AC
AA
AV
AA
AC
AC
AC
AG
AG
AA
AR
AB
AL
AU
AE
AA
BK
AZ

PART
RANK
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
C
C
C
C
C
C
C
C
C
C
C
C
D
C
D
D
C
C
E
E

DESCRIPTION
Multi frame cover
Stopper arm
Stopper plate
E type ring
Cam boss A1
Pipe A
Clutch spring A
Spring pin(φ2-7)
Cam boss A2
M bushing C
Roller shaft
Roller arm spring
Manual paper feed roller
Gear(20T)
Gear(24T)
Roller arm
Manual feed take-up roller
Screw(3×8)
Cam transmission arm
Arm
Manual feed cam shaft
Drive cam
MF clutch spring B
Cam clutch sleeve
Paper feeding joint plate
MF earth spring
Gear(27T)
Multi feeding solenoid
Spring B
Manual paper feeding pawl B
Manual paper feeding pawl A
Pawl A spring
Multi feed frame
Screw(3×10)
Vibration proof sheet
Stopper arm spring
Vibration proof sheet C
MB side guide F
MB side guide R
Screw(3×8)
Multi feed tray 1-U
UC manual feed gear
Multi feed tray 2
Multi feed tray 1-L
Tray arm
Screw(3×8)
Manual paper feeding multi unit
Manual paper tray unit

G Manual paper feeding multi unit
501

2

1

18

3
13

35

12
10

9

8

7

21
4 8

11
19

14

4

22

23

24
5

4

43
43

29

31

43
43
45
46

37
34

51

41

30

17
15 18

26

28

36
16

25

27

20
32

42

18

4

5

6

52
47

18

33

52

51

48

502
FCP5895

– 15 –

H Delivery frame unit
NO.
1
2
3
4
5
7
8
9
10
11
12
13
14
15
16
17
18
19
20

PARTS CODE
PBRSS0026QSZZ
XEBSD30P08000
CPWBF1177DS64
NROLR0092QSZZ
MLEVP0025QSZ2
LFRM-0065QSZZ
NBRGM5006BCZZ
NPLYZ0029QSZZ
XRESP50-06000
MSPRD0297QSZZ
NFANP0002QSZ1
XEBSD20P06000
PFILZ0004QSZZ
PMLT-0027QSZZ
PGIDM0062QSZZ
MSPRT0229GCAZ
NROLP0034QSZZ
NKOM-0002QSZZ
LFRM-0066QSZZ

PRICE NEW
RANK MARK
AF
AA
AS
AM
AD
AT
AB
AD
AA
AG
AX
AA
AM
AC
AP
AC
AD
AC
AT

PART
RANK
B
C
E
C
C
C
C
C
C
C
B
C
B
C
C
C
C
C
C

DESCRIPTION
Discharge brush
Screw(3×8)
Duplex/P-out sensor PWB
Delivery roller S
Delivery actuator
Delivery upper frame
Bearing
Delivery drive gear(34T)
E type ring
Delivery earth spring A
Cooling fan
Screw(2×6)
Ozone filter
Cleaning fan cushion
Delivery upper paper guide
FU spring R
Delivery roller
Delivery collar
Delivery lower frame

H Delivery frame unit

2
3
2 8

1

4

A

9

5

14

13

15
2
13

12
13

14
15

10

8
7

11
16

17

13

12

18

17

18

17

17
18

18

19

19
A

3
20

2
FCP05896

– 16 –

I TC case unit
NO.

PARTS CODE

XEBSE30P08000
PGIDH0031QSZZ
PSHEP0050QSZ1
LPLTM0059QSZZ
PSHEP0051QSZZ
LHLDZ0030QSZZ
DWIR-0466CSZZ
MSPRT0513FCZ1
PSHEP0052QSZZ
LHLDZ0032QSZZ
QSLP-0009QSZZ
PCASZ0006QSZZ
LHLDZ0031QSZ2
QSLP-0008QSZZ
PGIDM0032QSZZ
XEBSD30P06000
PSHEZ0125QSZZ
(Unit)
901 C H L D Z 0 0 3 0 R S 5 1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
16
17
19

PRICE NEW
RANK MARK
AA
AH
AD
AC
AB
AD
BG
AA
AB
AD
AD
AM
AH
AD
AE
AA
AE
BA

PART
RANK
C
C
C
C
C
C
B
C
C
C
C
C
C
C
C
C
C
E

DESCRIPTION
Screw(3×8)
TC front guide
TC sheet
TC upper PG earth spring plate
TC cover sheet F
TC holder F
Charger wire
MC tension spring
TC cover sheet R
TC holder R
TC electrode plate
TC case
Discharge holder
BC electrode plate
Separator guide
Screw(3×6)
Discharger delivery sheet
TC unit

J 250 sheets tray unit
NO.

PARTS CODE

LPLTM0053QSZ1
PSHEZ0054QSZ1
LHLDW1226FCZZ
LPLTM2642FCGZ
PGIDM0035QSZZ
PTME-0022QSZ1
XRESP40-06000
TLABH0064QSZ1
PGIDM0036QSZZ
PTME-0023QSZ1
MSPRC0090QSZZ
XEBSD30P08000
XWHSD30-08100
NGERH0193FCZZ
MSPRC0152QSZZ
MSPRC1145FCZZ
LSTPP0161FCZZ
GCASP0003QSZZ
TTAG-0004QSZZ
PSPAZ0022QSZZ
(Unit)
901 C C A S P 0 0 0 3 R S 5 2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20

PRICE NEW
RANK MARK
AS
AC
AB
AD
AP
AL
AA
AC
AP
AL
AD
AA
AA
AB
AB
AA
AB
AZ
AC
AC
BG

PART
RANK
C
C
C
C
C
C
C
D
C
C
C
C
C
C
C
C
C
D
D
C
E

DESCRIPTION
Rotation plate
Rotation plate sheet
Turn fasner
Tray rear plate
Guide F
250 Tray pawl F
E type ring
Indicator label
Guide R
250 Tray pawl R
Tray spring
Screw(3×8)
Washer
UC manual feed gear
Tray drawer lower spring D
Stopper spring
Rotation plate stopper
Tray case
Tray rotation tag
Rotation plate spacer
250 Tray unit

I TC case unit

J 250 sheets tray unit
8

3

1

2

19
1

2

9

2

9
8

3

20

17

7

5
10

1

7

6
4

7

11

10

11
12

4
5
17
1
6

14

15

12
13

16

14

13

19
18
16
1

17

FCP05897

FCP05898

– 17 –

K Packing material & Accessories
NO.
1
4
5
6
7
8
9
10
11
12
13
15
17
18
19
21
22

PARTS CODE
SPAKC0416RS11
SPAKC0145RS23
SPAKA0083RSZZ
SPAKA0120RSZZ
SSAKZ0003QSZZ
UBAGF0018YSZ1
SPAKA0134QSZZ
TCADZ0010QSZZ
LX-BZ0015QSZZ
LHLDW1226FCZZ
TTAG-0004QSZZ
CCLEZ0005RS51
TLABH0065QSZ1
TLABH0065QSZZ
CPAKA0084RS01
SPAKA0150RSZZ
TINSE0854QSZZ
TINSG0847QSZZ
TLABH0068QSZ1
TLABH0138QSZZ
SSAKA2343QCZZ
SPAKA0167RSZZ
TLABS3760FCZZ

PRICE NEW
RANK MARK
BU
N
BU
N
AD
BS
N
AF
AF
AE
AC
AF
AB
AC
AQ
AG
AN
AF
AA
AY
AY
AF
AD
AA
AA
AC

PART
RANK
D
D
D
D
D
D
D
D
C
C
D
E
D
D
B
D
D
D
D
D
D
D
D

DESCRIPTION
Packing case
Packing case
Top packing cushion
Top packing cushion OC
Vinyl bag
DV aluminum bag
OC protect sheet
Fixer screw caution card
2nd,3rd mirror fixing screw
Turn fasner
Tray rotation tag
Charger cleaner unit
Size display label
Size display label
Bottom add
Accessories protect packing cushion
Operation manual
Operation manual
Magnification select label
D-F cover label
Vinyl bag(260×380mm)
Tray protect sheet
CE mark label

(AL-1611)
(AL-1622)
(AL-1611)
(AL-1622)

(AL-1611)
(AL-1622)

(English)
(German)

K Packing material & Accessories

22

6

1
4
19
18

5
9

7
17
8

10
11

12

21

15

13

FCP05899

– 18 –

L 1ST Tray exteriors (AL-1622)
NO.
1
2
3
4
5
7
8
9
10
11
12
13
14
15
16
18
19
20
21
22
23
24
25
27
28
29
30
31
32
33
34
35
36
37
38
39
40

PARTS CODE
GCOV-0020QSZZ
GGAD-0001QSZZ
GGAD-0002QSZZ
LSUPP0083FCZZ
LPLTM0116QSZZ
XEBSE40P12000
GCOV-0019QSZ1
PGIDM0049QSZ1
PGIDM0048QSZ1
MSPRC0141QSZZ
MLOKZ0001QSZZ
NGERH1169FCZZ
PRNGP0019FCZZ
DHAI-0085QSZ3
CPWBF0019QSE3
MSPRD0135QSZZ
GLEGG0064FCZZ
PGIDM0050QSZ1
MARMP0015QSZZ
NROLP1060FCZZ
MSPRT0129QSZ1
GCOV-0021QSZ1
LPLTM0113QSZZ
XEPSD30P08X00
XHBSE30P10000
XHBSE40P10000
LPLTM0135QSZZ
LPLTM0138QSZZ
RCORF0006QSZZ
PSHEZ0172QSZZ
PSHEZ0173QSZZ
PSPO-0008QSZZ
PSPO-0009QSZZ
PSPO-0010QSZZ
PSPO-0011QSZZ
PSPO-0014QSZZ
PSHEZ0171QSZZ

PRICE NEW
RANK MARK
AQ
AE
AE
AB
AQ
AA
AR
AV
AW
AB
AC
AF
AA
BA
AV
AD
AC
AN
AD
AF
AC
AM
AH
AA
AA
AA
AF
AD
AL
AB
AB
AC
AD
AD
AD
AG
AD

PART
RANK
D
C
C
C
C
C
D
C
C
C
C
C
C
C
E
C
C
C
C
C
C
D
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C

DESCRIPTION
Rear cover
Edge guard upper
Edge guard lower
Supporter(LCBS-3)
Joint plate R
Screw(4×12)
Front cover
Guide L
Guide R
Transport PG lock spring
Transport PG lock
2ND Joint gear
V ring(GTW-6)
OP interface harness
1ST tray interface PWB
Joint earth spring
Rubber foot
1ST transport paper guide
1ST door arm
U-turn roller
Roller spring
2ND right cover
Guide R joint plate
Screw(3×8X)
Screw(3×10)
Screw(4×10)
Joint earth plate
2ND earth L rear
Ferrite core
Front sheet 2
Right cover sheet
Rear cover cushion 1
Rear cover cushion 2
Guide R cushion F
Guide R cushion R
Right cover cushion 3
Front sheet 1

L 1ST Tray exteriors (AL-1622)
29

2

7

36
1
7
31
29

7

7

4
38
35
7

5
27 11

18

7

3
13

19

9

14

12

7
10

27

15

28

12

37

32

11
8

7

16
7

34
7

19
20
21

40

23

33
39

7
25

30

34

7

22

23

22

21
24

FCP05900

– 19 –

M 1ST Tray paper feeding unit (AL1622)
NO.

PARTS CODE

NGERH1207FCZZ
MARMP0229FCZZ
MSPRT0128QSZZ
XRESP50-06000
LBOSZ1031FCZZ
MSPRC0161QSZZ
PPIPP0007QSZZ
NGERH1132FCZZ
NBRGM0501FCZZ
DHAI-0075QSZZ
NROLP0044QSZ2
VHPGP1A71A1-1
RPLU-0012QSZZ
NBRGC0188FCZZ
XRESP40-06000
LBOSZ1510FCZZ
PPIPP0109FCZZ
MSPRC1315FCZ1
LPINS0181FCZZ
LBOSZ1508FCZZ
QSW-B0003QSZZ
MSPRD0134QSZ2
NGERH0041QSZZ
NGERH0990FCZZ
PTME-0017QSZZ
MSPRT0130QSZ1
PTME-0016QSZZ
RPLU-0013QSZZ
XBBSD30P05000
MLEVP0039QSZ1
MLEVP0046QSZZ
CSFTZ0067RS51
LFRM-0031QSZ2
LPLTM0137QSZZ
LX-WZ0314FCZZ
MSPRC0157QSZZ
NBRGC0529FCZZ
PPIPP0011QSZZ
XBBSE30P06000
XRESP50-06000
XWHSD60-10000
RCORF0006QSZZ
MSPRD0156QSZZ
PSPO-0005QSZZ
PSPO-0007QSZZ
(Unit)
901 C F R M - 0 0 3 1 Q S 5 5
1
2
3
4
5
6
7
8
9
10
13
15
16
17
18
19
20
21
22
23
26
27
28
29
30
31
32
33
34
35
36
37
38
41
42
43
44
45
46
47
48
49
52
53
54

PRICE NEW
RANK MARK
AF
AE
AB
AA
AC
AF
AD
AH
AB
AR
AQ
AG
AN
AB
AA
AF
AB
AD
AA
AG
AF
AC
AF
AB
AD
AB
AD
AN
AA
AE
AD
AU
AU
AD
AA
AC
AD
AC
AA
AA
AA
AL
AB
AA
AB
BS

PART
RANK
C
C
C
C
C
C
C
C
C
C
C
B
B
C
C
C
C
C
C
C
B
C
C
C
C
C
C
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C

Joint gear(40T)
Joint arm
Joint arm spring
E type ring
Clutch boss
Clutch spring
Clutch sleeve
Clutch gear(29T)
Metal D(B-F6-7)
1ST harness
2ND transport roller
Photo transistor(GP1A71A1)
Paper feeding solenoid
PF bearing
E type ring
Cam boss A1
Pipe A
Clutch spring A
Spring pin
Cam boss A2
Tray detect switch
Paper feeding earth spring
2ND gear ID(18T/26T)
Gear(16T)
Paper feeding clutch pawl
Clutch pawl spring
Transport clutch pawl
Transport solenoid
Screw(3×5)
PPDI actuator
CICS actuator
Paper feeding roller
Paper feeding frame
Boss reinforce plate
Washer
Break spring
Bearing
Break sleeve
Screw(3×6)
E type ring
Washer
Ferrite core
PPD1ACT spring
Clutch pawl cushion
Transport clutch pawl cushion

E

Paper feeding unit (1ST tray)

DESCRIPTION

(AL-1622)

M 1ST Tray paper feeding unit (AL1622)
1

4

2
3
10

49

7

6
9

18

5
18

21

8
9

18

20

22

23

19

41

26
49
15

27

28

16

30

13

46

53
29
15

43
48
42

31

47

32

54

33

45

34

44
52

4
35

17
37

38
4

15
36

FCP05901

– 20 –

N MCU PWB
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52

53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73

PARTS CODE
VHI29F04027QS
QCNCM0017QSZZ
QCNCM0877FCZZ
QCNCM0923FC24
QCNCM2401SC0D
QCNCW0885FCZZ
VHISC65165V6T
VHVICPN38//-1
QCNCM0019QSZZ
QCNCW7191RC1B
QCNCM0923FC22
QCNCM1005MCZZ
QCNCM1006MCZZ
QCNCM1119LC0C
QCNCM1119LC0D
QCNCM2401SC0C
QCNCM2401SC0E
QCNCM7014SC0B
QCNCM7014SC0C
QCNCM7014SC0D
QCNCM7014SC0F
QCNCM7014SC0G
QCNCM7014SC1B
QCNCP0240QCZZ
QCNCP0341QCZZ
QCNCW0015QSZZ
QCNCW0024QSZZ
QCNCW0948FCZ3
QCNCW1124LC0D
QCNCW1124LC0H
RCRSP0016QSZZ
RCRUB0009QSZZ
RCRUB0010QSZZ
RFILN0019GCZZ
RMPTW4000QCJJ
RMPTW4103QCJJ
RMPTW4103QCJJ
RMPTW4103QCJJ
RMPTW4203QCJJ
RMPTW4222QCJJ
RMPTW4330QCJJ
RMPTW4330QCJJ
VCCCCY1HH101J
VCCCCY1HH120J
VCCCCY1HH7R0D
VCCUCY1AJ105Z
VCEAGU1CW106M
VCEAGU1CW107M
VCEAGU1CW226M
VCEAGU1CW476M
VCEAGA1HW107M
VCEAGA1VW106M
VCEAGU1VW476M
VCKYCY1EB223K
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1HB102K
VCKYCY1HB102K
VCKYCY1HB222K
VCKYCY1HB471K
VHDDSS133//-1
VHD1N4005E/-1
VHERD20EB3/-1
VHEUDZS5.6B-1
VHIHG73C025FD
VHIH8S/2350FP
VHILM358PS/-S
VHIMC7805CT-1
VHI27C00401QS
VHINJM2103M-1
VHIM66236FP-1
VHINJM2903M/VHINJM3414M-1
VHISLA7027MUL
VHITA7291S/-1
VHITC74ACT32F
VHITD62503F/VHIULN2003AN1

PRICE NEW
RANK MARK
AW
N
AC
AF
AF
AC
AG
BW
AF
AB
AG
AF
AB
AB
AC
AC
AB
AC
AD
AA
AB
AB
AB
AD
AA
AC
AE
AF
AC
AB
AC
AD
AP
AP
AC
AB
AB
AB
AB
AA
AB
AB
AB
AA
AA
AA
AC
AA
AB
AA
AB
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AA
AB
AA
AB
AB
AC
BE
AY
AC
AD
AM
AH
AT
AD
AF
AQ
AF
AF
AG
AE

PART
RANK
B
C
C
C
C
C
B
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
B
B
C
B
B
B
B
B
B
B
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B

DESCRIPTION
Flash ROM(29F04028QS)
Connector(4pin)
Connector(20pin)
Connector(24pin)
Connector(4pin)
Connector(1-171825-2)
IC(64M EDO DRAM)(SC65165V6T)
IC protector(ICPN38)
Connector(B2B-PH-K-YW)
Connector(12pin)
Connector(22pin)
Connector(2pin)
Connector(3pin)
Connector(3pin)
Connector(B4B-PH-K-M)(4pin)
Connector(3pin)
Connector(5pin)
Connector(2pin)
Connector(3pin)
Connector(4pin)
Connector(6pin)
Connector(7pin)
Connector(12pin)
Connector(2pin)
Connector(3pin)
Connector(5pin)
Connector(32pin)
Connector(3pin)
Connector(4pin)
Connector(8pin)
Crystal(19.6608MHz)
Crystal(22.000MHz)
Crystal(20.3094MHz)
Bead filter(ZE221)
Block resistor(0Ω×4 1/32W ±5%)
Block resistor(10KΩ×4 1/32W ±5%)
Block resistor(10KΩ×4 1/32W ±5%)
Block resistor(10KΩ×4 1/32W ±5%)
Block resistor(20KΩ×4 1/32W ±5%)
Block resistor(2.2KΩ×4 1/32W ±5%)
Resistor arrey(33Ω×4 1/32W ±5%)
Resistor arrey(33Ω×4 1/32W ±5%)
Capacitor(50WV 100pF)
Capacitor(50WV 12pF)
Capacitor(50WV 7.0pF)
Capacitor(10WV 1µF)
Capacitor(16WV 10µF)
Capacitor(16WV 100µF)
Capacitor(16WV 22µF)
Capacitor(16WV 47µF)
Capacitor(50WV 100µF)
Capacitor(35WV 10µF)
Capacitor(35WV 47µF)
Capacitor(25WV 0.022µF)
Capacitor(25WV 0.10µF)
Capacitor(25WV 0.10µF)
Capacitor(25WV 0.10µF)
Capacitor(25WV 0.10µF)
Capacitor(50WV 1000pF)
Capacitor(50WV 1000pF)
Capacitor(50WV 2200pF)
Capacitor(50WV 470pF)
Diode(DSS133)
Diode(1N4005E)
Zener diode(RD20EB3)
Zener diode(UDZS5.6B)
IC(HG73C025FD)
CPU(H8S/2350FP)
IC(LM358PS)
IC(MC7805CT-2)
EEPROM(27C00401)
IC(NJM2103M)
IC(M66236FP)
IC(NJM2903M)
IC(NJM3414M)
IC(SLA7027MUL)
IC(TA7291S)
IC(TC74ACT32F)
IC(TD62503F)
IC(ULN2003AN1)

– 21 –

[IC21]
[CN17]
[CN10]
[CN11]
[CN31]
[CN30]
[IC36]
[F1,2,3,6,7]
[CN19]
[CN12]
[CN5]
[CN36]
[CN22]
[CN28]
[CN15]
[CN29]
[CN1]
[CN18]
[CN32]
[CN27]
[CN26]
[CN6]
[CN4]
[CN14]
[CN33]
[CN35]
[CN2]
[CN23,CN24]
[CN20]
[CN13]
[X1]
[X2]
[X3]
[FB2,10,11]
[BR4,29,30]
[BR1∼3,6,7,11]
[BR13∼24,31,47]
[BR51,52,66∼73]
[BR43∼45,53∼65]
[BR50]
[BR5,8∼10,12,32∼38]
[BR40∼42,74∼82]
[C266,269,270,273]
[C253]
[C11,12]
[C15,281]
[C7,9,103]
[C25,32,33,35,37,41,42,73]
[C91,98,254,255]
[C262,263]
[C74]
[C102]
[C72,75,76,96]
[C13,14,17,24,30,89]
[C1,8,10,16,19,20,22,26∼29,31,34,36,43]
[C58,62,65,69,84,85,87,88,90]
[C104,113,114,131∼138,200∼203]
[C205∼251,264,271,272,279]
[C4,5,18,21,23,77∼81]
[C105∼112,115∼130]
[C39,61,68,95,101]
[C99,100,252]
[D2∼9]
[D10]
[D1]
[ZD1∼16]
[IC13]
[IC1]
[IC10]
[IC15]
[IC4]
[IC2]
[IC14]
[IC16]
[IC9]
[IC25]
[IC27]
[IC12]
[IC31]
[IC28,29,38]

N MCU PWB
NO.
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
901

PARTS CODE
RH-IX0009QSZZ
VHIW42C3103G/
VHI65808GN146
VHI74HCT244MF
VHI74LS244NS1
VHI74VHC08/-1
VRS-CY1JD000J
VRS-CY1JD000J
VRS-CY1JD100J
VRS-CY1JD101J
VRS-CY1JD102J
VRS-CY1JD103F
VRS-CY1JD103J
VRS-CY1JD103J
VRS-CY1JD203J
VRS-CY1JD203J
VRS-CY1JD203J
VRS-CY1JD205J
VRS-CY1JD220F
VRS-CY1JD221J
VRS-CY1JD242F
VRS-CY1JD242J
VRS-CY1JD330J
VRS-CY1JD331J
VRS-CY1JD472J
VRS-CY1JD473J
VRS-CY1JD511J
VRS-CY1JD680J
VRS-RE3DA1R0J
VRS-RE3DA131J
VRS-TP2BD221J
VRS-TP2BD472J
VRS-TP2BD473J
VRS-TS2AD101J
VSDTC114EK/-1
VS2SA1036KQRC
QCNCM0060QS06
QCNCP0242QCZZ
QSOCZ0002QSZZ
RH-IX0013QSZZ
VRS-CY1JD301J
(Unit)
CPWBX0096QSG7

PRICE NEW
RANK MARK
AP
AU
BF
AH
AH
AE
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AC
AB
AA
AA
AA
AB
AB
AB
AA
AD
AU
AA
CB

N

PART
RANK
B
B
B
B
B
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
B
C
C
C
B
C
E

DESCRIPTION
SRAM(UT61256JC-12)
IC(W42C31-03G)
IC(65808GN146)
IC(74HCT244MF)
IC(74LS244NS1)
IC(74VHC08)
Resistor(1/16W 0Ω ±5%)
Resistor(1/16W 0Ω ±5%)
Resistor(1/16W 10Ω ±5%)
Resistor(1/16W 100Ω ±5%)
Resistor(1/16W 1KΩ ±5%)
Resistor(1/16W 10KΩ ±1%)
Resistor(1/16W 10KΩ ±5%)
Resistor(1/16W 10KΩ ±5%)
Resistor(1/16W 20KΩ ±5%)
Resistor(1/16W 20KΩ ±5%)
Resistor(1/16W 20KΩ ±5%)
Resistor(1/16W 2MΩ ±5%)
Resistor(1/16W 22Ω ±1%)
Resistor(1/16W 220Ω ±5%)
Resistor(1/16W 2.4KΩ ±1%)
Resistor(1/16W 2.4KΩ ±5%)
Resistor(1/16W 33Ω ±5%)
Resistor(1/16W 330Ω ±5%)
Resistor(1/16W 4.7KΩ ±5%)
Resistor(1/16W 47KΩ ±5%)
Resistor(1/16W 510Ω ±5%)
Resistor(1/16W 68Ω ±5%)
Resistor(2W 1.0Ω ±5%)
Resistor(2W 130Ω ±5%)
Resistor(1/8W 220Ω ±5%)
Resistor(1/8W 4.7KΩ±5%)
Resistor(1/8W 47KΩ ±5%)
Resistor(1/10W 100Ω ±5%)
Transistor(DTC114EK)
Transistor(2SA1036KQRC)
Connector(4pin)
Connector(2pin)
Socket(8pin)
IC(MSM51V16165D)
Resistor(1/16W 300Ω ±5%)

[IC18,19,21,22,35,37]
[IC40]
[IC5]
[IC8]
[IC30,32,33]
[IC3,39]
[FB3,4,9,R94,115,202,206]
[R208,209,210,217]
[R8,51∼56,61∼66,216]
[R3,4,7,117,118]
[R13∼18,24,25,33,137,201]
[R29,31,72,74]
[R1,2,5,6,10,23,50]
[R70,73,85,93,97,205]
[R27,32,34,35]
[R57∼60,67,68]
[R138∼140,211]
[R28,30]
[R76]
[R107]
[R69,75]
[R81,100,109]
[R36∼49]
[R106,FB1]
[R19,21,26,77∼79,87]
[R101,102,113,114]
[R103]
[R105]
[R104,108]
[R71]
[R80,82∼84,86,88,89]
[R111,112]
[R110]
[FB8]
[Q1,Q3]
[Q2]
[CN38]
[CN16]
[IC4]
[IC34]
[R213,214]

MCU PWB

O COPY-Operation PWB
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23

PARTS CODE
QCNCW0020QSZZ
QCNCW0022QSZZ
QSW-P0008QSZZ
QSW-P0008QSZZ
QSW-P0008QSZZ
RCRMZ0001QSZZ
VCCCCY1HH300J
VCEAJU1CW476M
VCKYCY1HB102K
VCKYCY1HF103Z
VCCUCY1AJ105Z
VCKYCY1HF223Z
VHDDSS133//-1
VHIH8/3643/-1
VHITB62706AN/
VHITD62785F//
VHPLTC3650G01
VHP1LHLE-002A
VHP1LHLE-002A
VHP1LHLE-002A
VHP1LHLE-002A
VHP1LHEE-002A
VRD-RC2EY161J
VRS-CY1JD000J
VRS-CY1JD103J
VRS-CY1JD103J
VRS-CY1JD105J
VRS-CY1JD123J
VRS-CY1JD471J

PRICE NEW
RANK MARK
AG
AE
AC
AC
AC
AE
AB
AB
AA
AA
AC
AA
AA
AU
AS
AN
AQ
AC
AC
AC
AC
AC
AA
AA
AA
AA
AA
AA
AA

PART
RANK
C
C
B
B
B
B
C
C
C
C
C
C
B
B
B
B
B
B
B
B
B
B
C
C
C
C
C
C
C

DESCRIPTION
Connector(12pin)
Connector(25pin)
Switch(EVQ-23G-04K)
Switch(EVQ-23G-04K)
Switch(EVQ-23G-04K)
Crystal(9.8304MHZ)
Capacitor(50WV 30PF)
Capacitor(16WV 47µF)
Capacitor(50WV 1000PF)
Capacitor(50WV 0.010µF)
Capacitor(10WV 1µF)
Capacitor(50WV 0.022µF)
Diode(DSS133)
IC(H8/3643)
IC(TB62706AN)
IC(TD62785F)
Photo transistor(LTC3650G01)
LED (Green)(1LHLE-002A)
LED (Green)(1LHLE-002A)
LED (Green)(1LHLE-002A)
LED (Green)(1LHLE-002A)
LED (Red)(1LHEE-002A)
Resistor(1/4W 160Ω ±5%)
Resistor(1/16W 0Ω ±5%)
Resistor(1/16W 10KΩ ±5%)
Resistor(1/16W 10KΩ ±5%)
Resistor(1/16W 1MΩ ±5%)
Resistor(1/16W 12KΩ ±5%)
Resistor(1/16W 470Ω ±5%)

– 22 –

[CN1]
[CN3]
[K1∼5,7,8]
[K9,11∼14]
[K16∼20,22∼33]
[X1]
[C14,15]
[C1]
[C2∼7,10,11]
[C8]
[C9]
[C17]
[D56∼66]
[IC1]
[IC3]
[IC2]
[U1]
[D1∼4,6,7,10,11,12]
[D14,15,16,18∼24]
[D26∼33,35,36,37,38,39]
[D40,41,43,44,46∼50,52]
[D5,8,9,13,17,42,45,51,53,54]
[R1,9]
[R58,17]
[R11∼16,20∼24]
[R26∼44,46∼49]
[R45]
[R18]
[R8]

O COPY-Operation PWB
NO.

PARTS CODE

VRS-TP2BD6R8J
VS2SA1162-Y-1
VCKYCY1EF104Z
(Unit)
901 C P W B F 0 0 2 4 Q S E 7
24
25
26

PRICE NEW
RANK MARK
AA
AB
AA
BH

N

PART
RANK
C
Resistor(1/8W 6.8Ω ±5%)
B
Transistor(2SA1162)
C
Capacitor(25WV 0.10µF)
E

DESCRIPTION
[R2∼7,52∼57]
[Q1]
[C18]

COPY operation PWB

P Duplex/P-out sensor PWB
NO.

PARTS CODE

DHAI-0100QSZZ
LBNDJ0037FCZ1
VCKYPU1HB102K
VHPGP1S53V/-1
(Unit)
901 C P W B F 1 1 7 7 D S 6 4
1
2
3
4

PRICE NEW
RANK MARK
AG
AA
AA
AE
AS

PART
RANK
C
C
C
B
E

DESCRIPTION
Duplex/P-out sensor harness
Wire band(T18S)
Capacitor(50WV 0.001µF)
Photo transistor(GP1S53V)
Duplex/P-out sensor PWB

Q MHPS PWB
NO.

PARTS CODE

DHAI-0096QSZZ
LBNDJ0037FCZ1
VCKYPU1HB102K
VHPGP1S53V/-1
(Unit)
901 C P W B F 1 1 7 7 D S 6 3
1
2
3
4

PRICE NEW
RANK MARK
AF
AA
AA
AE
AR

PART
RANK
C
C
C
B
E

DESCRIPTION
Scanner HP sensor harness
Wire band(T18S)
Capacitor(50WV 0.001µF)
Photo transistor(GP1S53V)
MHPS PWB

R Tray sensor PWB
NO.

PARTS CODE

DHAI-0092QSZZ
LBNDJ0037FCZ1
VCKYPU1HB102K
VHPGP1S53V/-1
(Unit)
901 C P W B F 1 1 7 7 D S 6 5
1
2
3
4

PRICE NEW
RANK MARK
AF
AA
AA
AE
AR

PART
RANK
C
C
C
B
E

DESCRIPTION
Tray empty sensor harness
Wire band(T18S)
Capacitor(50WV 0.001µF)
Photo transistor(GP1S53V)
Tray sensor PWB

S Manual paper feeding sensor PWB
NO.

PARTS CODE

DHAI-0093QSZZ
LBNDJ0037FCZ1
VCKYPU1HB102K
VHPGP1S53V/-1
(Unit)
901 C P W B F 1 1 7 7 D S 6 6
1
2
3
4

PRICE NEW
RANK MARK
AF
AA
AA
AE
AR

PART
RANK
C
C
C
B
E

DESCRIPTION
Hand empty sensor harness
Wire band(T18S)
Capacitor(50WV 0.001µF)
Photo transistor(GP1S53V)
Manual paper feeding sensor PWB

T PS sensor PWB
NO.

PARTS CODE

DHAI-0094QSZZ
LBNDJ0037FCZ1
VCKYPU1HB102K
VHPGP1S53V/-1
(Unit)
901 C P W B F 1 1 7 7 D S 6 7
1
2
3
4

PRICE NEW
RANK MARK
AF
AA
AA
AE
AR

PART
RANK
C
C
C
B
E

DESCRIPTION
Paper in sensor harness
Wire band(T18S)
Capacitor(50WV 0.001µF)
Photo transistor(GP1S53V)
PS sensor PWB

U RCU PWB
NO.

PARTS CODE

DHAI-0133QSZZ
QCNCM0029QSZZ
(Unit)
901 C P W B F 0 0 3 3 Q S E 1
1
2

PRICE NEW
RANK MARK
AH
AK
AP

PART
RANK
C
RCS PWB harness
C
Connector(MD-S5130)(5pin)
E

RCU PWB

– 23 –

DESCRIPTION

V Low voltage power supply unit
NO.

!
!

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80

PARTS CODE
0AV1690000106
0AV1690000088
0AV1560000002
0AV1690000111
0AV1480000083
0AV1480000079
0AV1390000198
0AV1610000091
0AV1390000184
0AV1390000107
0AV1610000108
0AV1390000108
0AV1390000177
0AV1390000181
0AV1390000110
0AV1610000109
0AV1560000005
0AV1610000114
0AV3050086000
0AV3060027000
0AV3060043000
0AV3070058000
0AV3050036000
0AV3050019000
0AV3070085000
0AV3070056000
0AV3050097000
0AV3050099000
0AV3050098000
0AV3070057000
0AV3070074000
0AV3070081000
0AV3060044000
0AV3042605000
0AV3001015090
0AV3020143999
0AV3021815090
0AV2014733030
0AV2041013020
0AV2011213030
0AV2041213030
0AV2011043030
0AV2011543020
0AV2013333010
0AV2011003020
0AV2091083042
0AV2043303010
0AV2011033010
0AV2016833010
0AV2011013010
0AV2021043062
0AV2016803030
0AV2015633010
0AV2011023010
0AV2012243020
0AV2011033030
0AV2011833010
0AV2014723010
0AV2990007000
0AV2014713010
0AV2011223030
0AV2014733010
0AV2012203010
0AV4070062000
0AV4120002000
0AV4080010000
0AV4120013000
0AV4070065000
0AV4000135411
0AV3160034000
0AV5140022000
0AV5190009000
0AV3180000004
0AV3082561300
0AV3090076000
0AV3090077000
0AV3090080000
0AV3090081000
0AV5030126000
0AV5030132000

PRICE NEW
RANK MARK
AD
AC
AD
AD
AC
AC
AR
AC
AC
AC
AD
AC
AC
AE
AF
AC
AH
AD
AB
AH
AC
AC
AF
AF
AC
AD
AG
AD
AG
AC
AC
AC
AC
AN
AD
AD
AC
AB
AC
AB
AC
AA
AC
AA
AA
AC
AB
AA
AA
AA
AD
AA
AA
AA
AA
AB
AA
AA
AC
AA
AB
AA
AA
AF
AC
AP
AC
AQ
BD
AQ
AF
AL
AL
AF
AF
AN
AN
AL
AG
AL

PART
RANK
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
B
B
B
B
B
B
B
B
B
C
C

DESCRIPTION
Ceramic capacitor(DE1007-486E222M-KH)(2200PF)
Ceramic capacitor(TRPE132R104K50)(0.1µF 50V)
Film capacitor(RE104-C)(0.1µF 250V)
Ceramic capacitor(DE1210-2E222M-KX)(2200PF)
Film capacitor(ECQB1H102JF4)(1000PF 50V)
Film capacitor(ECQB1H103JF4)(0.01µF 50V)
Al-electrolytic capacitor(LLS2G151MHLZ)(150µF 400V)
Ceramic capacitor(DE0905-979R102K1K)(1000PF 1KV)
Al-electrolytic capacitor(UPJ1H2R2MDH)(2.2µF 50V)
Aluminum Electrolytic capasitor(0.47µF 50V)
Ceramic capacitor(DE1307-486R222K1K)(2200PF 1KV)
Aluminum Electrolytic capasitor(22µF 35V)
Al-electrolytic capacitor(UPJ1E221MPH)(220µF 25V)
Al-electrolytic capacitor(UHD1A102MPR)(1000µF 10V)
Al-electrolytic capacitor(UPJ1V681MHH)(680µF 35V)
Ceramic capacitor(DE0705-979R471K1K)(470PF 1KV)
Film capacitor(RE474-C)(0.47µF 250V)
Ceramic capacitor(DE0605-979SL680J2K)(68PF 2KV)
Diode(1SS270)
Diode(D3SB60)(4A 600V)
Diode(RLIN4005-E)(1A 600V)
Zener diode(RD5.6ES)
Diode(RG1C)
Diode(ERA91-02)
Zener diode(RD33ES)
Zener diode(RD20ES)(400MW)
Diode(SF10LC20U)(10A 200V)
Diode(D1NL20U)
Diode(SF5SC4)(5A 40V)
Zener diode(RD30ES)
Zener diode(RD13ES)
Zener diode(RD3.9ES)
Diode(ERA1504)(1A 400V)
Transistor(2SK2605)(5A 800V)
Transistor(2SA1015)(-0.15A - 50V)
Transistor(DTC114ESA)(0.1A 50V)
Transistor(2SC1815)(0.15A 50V)
Fixed carbon film resistor(RDF50S470KΩJ)(470KΩ 1/2W)
Fusing resistor(RF25S100ΩJ)(100Ω 1/4W)
Fixed carbon film resistor(RDF50S120ΩJ)(120Ω 1/2W)
Fusing resistor(RF50S120ΩJ)(120Ω 1/2W)
Flame proof fixed carbon film resistor(100KΩ 1/2W)
Fixed carbon film resistor(RDF25S150KΩJ)(150KΩ 1/4W)
Flame proof fixed carbon film resistor(33KΩ 1/6W)
Flame proof fixed carbon film resistor(10Ω 1/4W)
Special power resistor(SPR1B0.1ΩJ)(0.1Ω 1W)
Fusing resistor(RF16S33ΩJ)(33Ω 1/6W)
Flame proof fixed carbon film resistor(10KΩ 1/6W)
Flame proof fixed carbon film resistor(68KΩ 1/6W)
Flame proof fixed carbon film resistor(100Ω 1/6W)
Metal film resistor(RSS3FB100KΩJ)(100KΩ 3W)
Flame proof fixed carbon film resistor(1/2W 68Ω)
Flame proof fixed carbon film resistor(1/6W 56KΩ)
Flame proof fixed carbon film resistor(1KΩ 1/6W)
Flame proof carbon resistor(220KΩ 1/4W)
Fixed carbon film resistor(RDF50S10KΩJ)(10KΩ 1/2W)
Flame proof fixed carbon film resistor(18KΩ 1/6W)
Flame proof fixed carbon film resistor(4.7KΩ 1/6W)
Metal film resistor(2.2KΩ 1/6W)
Flame proof carbon resistor(470Ω 1/6W)
Fixed carbon film resistor(RDF50S1.2KΩJ)(1.2KΩ 1/2W)
Flame proof fixed carbon film resistor(47KΩ 1/6W)
Flame proof fixed carbon film resistor(22Ω 1/6W)
Inductor(LF-4Z-E822)
Inductor(B-01-A)
Inductor(DR-18728B)
Inductor(T3140P3206536HW)
Inductor(DRB25-16196A)
Transformer(N-T01-354-D11)
Transformer(TM1661PL(L)LF113)
Thermistor(M10010T3C)
Varistor(470V)(127V)
Photo coupler(S21ME3Y)
Photo coupler(PS2561)
IC(MM1431ATT)
IC(FA3647P)
IC(PQ12RF11)
IC(UPC29M33HF)
Connector(B03P-VL)
Connector(B04P-VL)

– 24 –

[C20,C021]
[C4,C019,C114,C012
[C5,C006]
[C1,C003,C007]
[C8,C023]
[C9,0014]
[C10]
[C11,C101]
[C106]
[C13,C112]
[C15]
[C17,C018,C107
[C102]
[C103,C104]
[C105,C117]
[C113]
[C24]
[C16]
[D1,D014,D106,D108
[D2]
[D3,D004,D012,D015]
[D5,D110]
[D6]
[D7,D008,D010]
[D9]
[D11]
[D101]
[D102]
[D103]
[D107,D013]
[D109]
[D112]
[D114]
[Q1]
[Q2]
[Q114]
[Q104,Q106
[R1,R027]
[R2]
[R3]
[R4]
[R5,R006]
[R7,R008]
[R10,R014]
[R11]
[R12]
[R13]
[R15,R019,R023
[R16]
[R17]
[R18]
[R20]
[R21]
[R22]
[R24,R025]
[R101]
[R9]
[R116]
[R109,R111]
[R103,R105,R110,R112]
[R117,R118]
[R26]
[R132]
[L1,L002]
[L3,L101
[L5,L007]
[L104]
[L6]
[T1]
[TR1]
[TH1]
[X1]
[PC1]
[PC2,PC003]
[IC1,IC102]
[IC2]
[IC101]
[IC103]
[CN1]
[CN2]

V Low voltage power supply unit
NO.

!
!
!

81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100

!

901

PARTS CODE
0AV5030133000
0AV5030134000
0AV5030135000
0AV5030136000
0AV5080010000
0AV5060085000
0AV5060083000
0AV5060092000
0AV5050005000
0AV5130008000
0AV7100003000
0AV6114125811
0AV8117730414
0AV8117730514
0AV7414138611
0AV5110012000
0AV5110001000
0AV5110002000
0AV5110002000
0AV5110002000
0AV5110004000
0AV5110004000
0AV5190024000
(Unit)
RDENC0009QSZZ

PRICE NEW
RANK MARK
AF
AL
AG
AC
AQ
AF
AF
AE
AA
AC
AE
AF
AB
AB
AD
AB
AA
AA
AA
AA
AA
AA
AK
BK

PART
RANK
C
C
C
C
B
A
A
A
C
B
C
C
C
C
D
C
C
C
C
C
C
C
B
E

DESCRIPTION
Connector(B02P-XL)
Connector(B06P-VL)
Connector(B26B-PHDSS-B)
Connector(B3B-PH-K-S)
Relay(FTR-H1AA024V)
Fuse(215SB-10AA-SB)(10A/250V)
Fuse(215SB-3R15AA-SB)(3.15A/250V)
Fuse(382RB4AR-ALT)(4A/250V)
Fuse holder(PFC5000-0203)
Terminal(TP00370-41)
Insulator(M-30AD-D-3)
Heatsink(LM41258)
Screw(NACPEW-B3×8ZF)(B3×8)
Screw(M3×10)
Label(LV41386)
Jumper wire(RJ-SKA-06)(6mm)
Jumper wire(RJ-SCA-06)(M0.6 10mm)
Jumper wire(RJ-SEA-06)(M0.6 15mm)
Jumper wire(RJ-SEA-06)(M0.6 15mm)
Jumper wire(RJ-SEA-06)(M0.6 15mm)
Jumper wire(M0.6 20mm)
Jumper wire(M0.6 20mm)
Arrestor(RA-102M-C6-Y)

[CN3]
[CN4]
[CN101]
[CN101]
[RL1]
[F1,F003]
[F2]
[F101,F102]

[RJ702,RJ712,RJ723
[RJ716,RJ719,RJ725
[RJ703,RJ704,RJ706,RJ707
[RJ724,RJ727
[RJ739,RJ745]
[RJ705,RJ708,RJ709,RJ711
[RJ717,RJ718]
[Z1,Z002]

Low voltage power supply unit

W ERDH OP PWB
NO.

PARTS CODE

DHAI-0116QSZZ
QCNCW0022QSZZ
QSW-P0008QSZZ
VHP1LHLE-002A
(Unit)
901 C P W B F 0 0 2 5 Q S E 3
1
2
3
4

PRICE NEW
RANK MARK
AC
AE
AC
AC
AH

PART
RANK
C
C
B
B
E

DESCRIPTION
Panel ERDH harness
Connector(25pin)
Switch(EVQ-23G-04K)
LED (Red)(1LHLE-002A)
ERDH operation PWB

X 1ST Tray interface PWB (AL-1622)
NO.

PARTS CODE

QCNCM0877FCZZ
QCNCM0923FC16
QCNCM0923FC22
VCEAGU1VW476M
VCKYTV1HB222K
VCKYTV1HF104Z
VHDDAN202K/-1
VHDDAP202K/-1
VHITC74HC151F
VHIULN2003AN1
VHVICPN38//-1
VRS-TP2BD000J
VRS-TS2AD103J
VCKYPU1HB102K
(Unit)
901 C P W B F 0 0 1 9 Q S E 3
1
2
3
4
5
6
7
8
9
10
11
12
13
15

PRICE NEW
RANK MARK
AF
AF
AF
AB
AA
AA
AB
AB
AG
AE
AF
AA
AA
AA
AV

PART
RANK
C
C
C
C
C
C
B
B
B
B
B
C
C
C
E

DESCRIPTION
Connector(20pin)
Connector(16pin)
Connector(22Pin)
Capacitor(35WV 47µF)
Capacitor(50WV 2200PF)
Capacitor(50WV 0.10µF)
Diode(DAN202K)
Diode(DAP202K)
IC(TC74H151F)
IC(ULN2003AN1)
IC protector(ICPN38)
Resistor(1/8W 0Ω ±5%)
Resistor(1/10W 10KΩ ±5%)
Capacitor(50WV 0.001µF)

[CN-C]
[CN-B]
[CN-A]
[C1,2,3]
[C4,5,6,7,8,9,10]
[C11,15]
[D1,2]
[D3,4]
[IC1]
[IC2]
[ICP1]
[J1∼23]
[R1,2,3,4]
[C22∼24]

1ST tray interface PWB

Y SPF Exteriors (AL-1622)
NO.
1
2
3
4
5
6
7
8
9
10
11
12
14
15
16

PARTS CODE
LSOU-0015QSZ1
LSOU-0017QSZ2
LPLTP0107QSZZ
LPLTP0108QSZZ
NGERR0377FCZZ
XEPSD30P08X00
NGERH0193FCZZ
MSPRP0059QSZZ
MLEVP0035QSZ1
VHPGP1A71A1-1
DHAI-0070QSZZ
PCOVP0039QSZ2
CFRM-0029RS51
GCAB-0023QSZ1
GCAB-0022QSZZ

PRICE NEW
RANK MARK
AV
AP
AH
AH
AD
AA
AB
AD
AD
AG
AH
AQ
BL
AP
AK

PART
RANK
D
D
C
C
C
C
C
C
C
B
C
C
E
D
D

DESCRIPTION
Original tray
Original tray S
Control plate F
Control plate R
Manual feed gear
Screw(3×8X)
UC manual feed gear
Control plate spring
Original detect lever ACT
Photo sensor(GP1A71A1)
Original tray harness
Rack cover
Pick up unit
Rear exterior
Front exterior

– 25 –

Y SPF Exteriors (AL-1622)
NO.
19
20
21
22
23
24
25
26
27
28
29
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
50
51
52
53
54
55
56

PARTS CODE
MHNG-0009QSZ1
XEBSE40P12000
LSOU-0018QSZ1
PCUSS0013QSZ3
PSHEZ0077QSZ1
XEBSE30P08000
PSHEZ0078QSZZ
NROLP0011QSZZ
PSPO-0001QSZZ
NSFTZ0013QSZZ
NBRGM0501FCZZ
LPLTM0110QSZZ
XHBSE30P08000
MSPRD0124QSZZ
MSPRD0125QSZZ
NSFTZ0030QSZZ
NROLP0010QSZZ
NSFTZ0009QSZZ
MSPRP0123QSZZ
MSPRP0060QSZZ
LPLTM0109QSZZ
MHNG-0010QSZ1
PSHEZ0068QSZZ
PSHEZ0069QSZZ
MLEVF0040QSZZ
LPLTM0111QSZZ
DHAI-0076QSZ3
CPWBF0022QSE3
XWVSD40-05000
LX-BZ3008SC0M
DHAI-0154QSZZ
MSPRC0149QSZZ
MSPRD0154QSZZ
XRESP20-04000
XEBSE40P14000
RCORF0026FCZZ

PRICE NEW
RANK MARK
AV
AA
BF
AZ
AE
AA
AF
AD
AB
AF
AB
AG
AA
AC
AC
AL
AD
AE
AD
AD
AG
AV
AC
AE
AD
AC
BA
AZ
AA
AA
AD
AC
AD
AA
AA
AL

PART
RANK
C
C
D
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
E
C
C
C
C
C
C
C
C

Y SPF Exteriors (AL-1622)

DESCRIPTION
SPF hinge L
Screw(4×12)
Base tray R
OC mat
OC mat sheet F
Screw(3×8)
OC mat sheet R
Delivery roller
Sponge
Delivery shaft
Metal D
Release plate
Screw(3×8)
Delivery spring F
Delivery spring R
Pressure release shft
Transport roller
Transport shaft
Transport spring
Transport spring
Base tray reinforce plate
SPF hinge R
PS sheet
Base tray sheet
SPF pressure lever
Reinforce plate earth
Interface harness
SPF interface PWB P-S
Washer
Screw(M3×L8)
SPF ground wire
SPF earth spring
Earth spring
E type ring
Screw(4×14)
Core(TFC-16813)

2

4

1

15
14
20 32
3
9

5
10
9

6

7
8

10

16

6

20

20

55
11

56
12

45

47

48

6

46

24

6

50

19

51

20

24

44
43

21
22

42

24

42
48

25
24
26

28

23

29

27

31

54
37

36 35

24

26 27

29

34

54

33
50

– 26 –

41
48
20

20

36
38 36

37

24

38
53
24 36
52

40

24
39
24
24

24

FCP05902

Z SPF Pick up unit (AL-1622)
NO.
1
2
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
41
42
43
44
45
46
47
48
501

PARTS CODE
GCAB-0025QSZZ
PSPO-0002QSZZ
MARMP0003QSZ1
LSTPP0001QSZZ
XEBSE30P08000
CPWBF0017RS51
DHAI-0071QSZZ
MLEVP0090QSZ1
MLEVP0010QSZZ
RPLU-0004QSZ1
XBPSD30P05KS0
MARMP0002QSZZ
MSPRT0067QSZZ
XRESP40-06000
NGERH0073QSZZ
PPIPP0008QSZZ
MSPRC1316FCZ1
LBOSZ1508FCZZ
LBSHZ0303FCZZ
NSFTZ0032QSZZ
NPLYZ0010QSZZ
XRESP30-06000
MSPRT0066QSZZ
PTME-0019QSZZ
NROLP0024QSZZ
NGERH0990FCZZ
XPSSP20-07000
NGERH0992FCZZ
NROLR0922FCZZ
NSFTZ0011QSZZ
MSPRC0115QSZZ
MARMP0004QSZZ
LFRM-0029QSZ1
MLEVP0037QSZZ
MSPRD0133QSZZ
MSPRD0132QSZZ
MARMM0013QSZZ
XEBSE30P08000
MARMM0014QSZZ
MSPRD0140QSZZ
PGIDM0047QSZZ
GCAB-0024QSZZ
LBSHZ0006QSZZ
CFRM-0029RS51

PRICE NEW
RANK MARK
AP
AC
AD
AD
AA
AU
AH
AC
AE
AQ
AA
AD
AB
AA
AE
AD
AE
AG
AC
AH
AE
AA
AC
AD
AL
AB
AA
AB
AR
AG
AB
AF
AQ
AD
AC
AC
AF
AA
AE
AC
AP
AN
AC
BL

PART
RANK
D
C
C
C
C
E
C
C
C
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
D
C
E

DESCRIPTION
Open and shut exterior
Stopper sponge
Stopper arm
Paper stopper
Screw(3×8)
SPF sensor PWB
Sensor harness
Set detect lever ACT
Open and shut detect lever ACT
PU solenoid
Screw(3×5KS)
Solenoid arm
Solenoid arm spring
E type ring
Clutch gear(20T)
SPF clutch sleeve
MF clutch spring B
Cam boss A2
M bushing C
Clutch shaft
20MXL pulley
E type ring
Clutch pawl spring
Clutch pawl
Pick up roller
Gear(16T)
Spring pin(φ2-7)
Gear(20T)
Manual paper feed roller
Paper feeding shaft
Paper feeding spring
Pick up arm
Paper feeding frame
Open and shut detect lever
Open and shut detect spring
JAM release spring
U-turn PG arm F
Screw(3×8)
U-turn PG arm R
JAM release spring R
U-turn paper guide
U-turn PG exterior
M bushing 2
Pick up unit

– 27 –

Z SPF Pick up unit (AL-1622)

501
1

2

11
17

15
16

4

18

23

24

20

12

13

12

5

7

21

20

14
6

19 15

9
10

9
8

25

26

36
37

6

33

20

30 15
27
35
6

29

28

29
34
31

30
48

43

43
32

29

45
44

43
46

43

41
42
47
43
FCP05903

– 28 –

[ SPF Transport unit (AL-1622)
NO.
1
2
3
4
5
6
7
8
9
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
50
51
52
53
54
55

PARTS CODE
PSHEZ2174FCZZ
PSHEZ7242XCZZ
LPLTP0235QSZ1
MSPRC0062QSZZ
PGIDM0045QSZ5
NROLM0041QSZ1
PBRSS0008QSZ1
PGIDH0046QSZ1
XEBSE30P08000
DHAI-0073QSZ1
LBNDJ2003SCZZ
RMOTP0020QSZZ
XBBSD30P05000
QCNCM1003FCZZ
QCNCM1004FCZZ
QCNCM0999FCZZ
LFRM-0030QSZZ
LHLDW1263FCZZ
XRESP50-06000
PSHEP3029FCZZ
NBLTT0011QSZZ
NGERH0047QSZZ
XPSSP20-09000
NBRGM0501FCZZ
NGERH0079QSZZ
XRESP40-06000
PCLC-0016QSZZ
NBRGC0017QSZZ
MLEVP0038QSZZ
LFRM-0028QSZ1
MSPRP0065QSZZ
PGIDM0043QSZ1
PTME-0015QSZZ
RDTCT0006QSZZ
MSPRC0063QSZZ
NPLYZ0146FCZZ
NBLTT0010QSZZ
JKNBZ0005QSZZ
NROLM0040QSZ1
PGIDH0044QSZZ
PSHEZ0070QSZZ
NROLM0042QSZ1
PSHEZ0071QSZZ
XEBSE30P08000
XEBSD30P10000
PTPE-0018QSZZ
RCORF6661RCZZ
LPLTP0131QSZZ
MLEVP0047QSZ1
MSPRC0153QSZZ
VHPGP1A71A1-1
PSHEZ0162QSZZ
PSHEZ0252QSZZ

PRICE NEW
RANK MARK
AB
AE
AD
AC
AN
AR
AH
AK
AA
AV
AA
BC
AA
AD
AD
AC
AH
AC
AA
AA
AG
AF
AA
AB
AD
AA
AU
AC
AD
AD
AD
AQ
AD
AL
AB
AB
AG
AE
AS
AK
AG
AR
AE
AA
AA
AC
AK
AD
AD
AB
AG
AB
AF

PART
RANK
C
C
C
C
C
C
B
C
C
C
C
B
C
C
C
C
C
C
C
C
B
C
C
C
C
C
B
C
C
C
C
C
C
B
C
C
B
C
C
C
C
C
C
C
C
C
C
C
C
C
B
C
C

DESCRIPTION
Paper feeding sheet
Separate sheet
Separate plate
Pressure spring
PF paper guide upper
Delivery roller
Discharge brush
PF paper guide lower
Screw(3×8)
Separator harness S-SPF
Wire band(PLT1M)
SPF motor
Screw(3×5)
Connector(BU06P-TR-PH)
Connector(BU07P-TR-PH)
Connector(BU02P-TR-PH)
Drive frame
Wire holder(EDS0607M)
E type ring
Flange sheet DUP2
Belt(B85MXL4.8)
Gear Gear(48T/15T)
Spring pin(φ2-9)
Metal D
Gear(30T)
E type ring
Transport clutch
Bearing R
SPF lever
Frame R
Open and shut lock spring
Transport paper guide R
U-turn PG lock pawl
Inlet detect sensor
Delivery PG spring
Pulley(22MXL)
Belt(74MXL4.8)
JAM release knob(22P)
Transport roller
Delivery paper guide R
White sheet
PS roller
SPF delivery PG sheet
Screw(3×8)
Screw(3×10)
Motor earth tape
Core(SFC-4)
Book sensor fixer
Book sensor ACT
Book sensor spring
Photo sensor(GP1A71A1)
Harnss protect sheet
Front separate sheet

– 29 –

[ SPF Transport unit (AL-1622)
11
2
1

13

3

12

12
4

55

54

15
5

47

9
48
6

45

7

12
45

45
14
18
14

17

8
30

23

21

24

20

25

19

26 22

27
29

28
45

32

20
25

9

31

33

9
32

34

25

36

20
46

35

25
45
24

36

25

20

39

40
34

20
53

41

37

38

44

9

42

50
52

43

44

51

FCP05904

– 30 –

16

\ SPF interface PWB (AL-1622)
NO.

PARTS CODE

QCNCM0923FC22
QCNCM0923FC24
QCNCM7014SC0B
QCNCM7014SC0C
QCNCM7014SC0G
VCEAGA1VW106M
VCEAGU1VW476M
VCKYTV1HB102K
VCKYTV1HB222K
VCKYTV1HB471K
VCKYTV1HF104Z
VHDDSS133//-1
VHISLA7027MUL
VHITC74HC151F
VHIULN2003AN1
VHVICPN38//-1
VRS-HT3AA1R5J
VRS-TP2BD000J
VRS-TP2BD221J
VRS-TS2AD103J
VRS-TS2AD152J
VRS-TS2AD242J
VRS-TS2AD473J
VRS-TS2AD912J
(Unit)
901 C P W B F 0 0 2 2 Q S E 3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24

PRICE NEW
RANK MARK
AF
AF
AD
AA
AB
AA
AB
AA
AA
AA
AA
AA
AQ
AG
AE
AF
AB
AA
AB
AA
AA
AA
AA
AA
AZ

PART
RANK
C
C
C
C
C
C
C
C
C
C
C
B
B
B
B
B
C
C
C
C
C
C
C
C
E

DESCRIPTION
Connector(22Pin)
Connector(24pin)
Connector(2pin)
Connector(3pin)
Connector(7pin)
Capacitor(35WV 10µF)
Capacitor(35WV 47µF)
Capacitor(50WV 1000PF)
Capacitor(50WV 2200PF)
Capacitor(50WV 470PF)
Capacitor(50WV 0.10µF)
Diode(DSS133)
IC(SLA7027MUL)
IC(TC74HC151F)
IC(ULN2003AN1)
Varistor(ICPN38)
Resistor(1W 1.5Ω ±5%)
Resistor(1/8W 0Ω ±5%)
Resistor(1/8W 220Ω ±5%)
Resistor(1/10W 10KΩ ±5%)
Resistor(1/10W 1.5KΩ ±5%)
Resistor(1/10W 2.4KΩ ±5%)
Resistor(1/10W 47KΩ ±5%)
Resistor(1/10W 9.1KΩ ±5%)

[CN2]
[CN1]
[CN4]
[CN5]
[CN3]
[C2,18]
[C1]
[C9∼14,15,16,17]
[C7,8]
[C5,6]
[C3,4,19∼22]
[D1∼8]
[IC2]
[IC1]
[IC3]
[ICP1]
[R1,2]
[J1∼26]
[R4]
[R10∼16]
[R3]
[R6,7]
[R8,9]
[R5]

SPF interface PWB P-S

] SPF sensor PWB (AL-1622)
NO.

PARTS CODE

QCNCM7014SC0G
VCKYPU1HF223Z
VHPGP1S58V/-1
VRD-HT2EY121J
VRD-HT2EY241J
(Unit)
901 C P W B F 0 0 1 7 R S 5 1
1
2
3
4
5

PRICE NEW
RANK MARK
AB
AA
AE
AA
AA
AU

PART
RANK
C
C
B
C
C
E

DESCRIPTION
Connector(7pin)
Capacitor(50WV 0.022µF)
Photo sensor(GP1S58V)
Resistor(1/4W 120Ω ±5%)
Resistor(1/4W 240Ω ±5%)
SPF sensor PWB

– 31 –

[CN101]
[C101]
[PT101∼105]
[R101,102]
[R103]

■

Index

PARTS CODE
[C]
CARMP0010QS01
CARMP0011QS01
CBTN-0016QS01
CBTN-0019QS02
CBTN-0021QS01
CBTN-0022QS01
CCAB-0012QS1G
CCAB-0012QS1H
CCASP0003RS52
CCLEZ0005RS51
CCOVH0010RS51
CDAIU0012QS06
CFIX-0008QS02
CFRM-0017QS01
CFRM-0018QS01
CFRM-0020RS51
CFRM-0029RS51
"
CFRM-0031QS55
CGERH0011RS51
CHAI-0107RS51
CHAI-0109RS51
CHLDZ0030RS51
"
CHNG-0007QS01
CLNS-0003RS53
CMIR-0008QS32
"
CPAKA0084RS01
CPLTM0047QS02
CPLTM0055QS01
CPLTM0084QS01
CPLTM0114QS01
CPLTM0155QS02
CPLTM0156QS02
CPLTP0060RS52
CPWBF0017RS51
"
CPWBF0019QSE3
"
CPWBF0022QSE3
"
CPWBF0024QSE7
"
CPWBF0025QSE3
"
CPWBF0033QSE1
"
CPWBF1177DS63
"
CPWBF1177DS64
"
CPWBF1177DS65
"
CPWBF1177DS66
"
CPWBF1177DS67
"
CPWBX0096QSG7
"
CREFL0004QS33
CROLP1115FC01
CSFTZ0066RS71
CSFTZ0067RS51
CSOU-0009QS32
CSW-M0007RS51
[D]
DHAI-0070QSZZ
DHAI-0071QSZZ
DHAI-0073QSZ1
DHAI-0075QSZZ
DHAI-0076QSZ3
DHAI-0085QSZ3
DHAI-0089QSZ1
DHAI-0090QSZZ
DHAI-0091QSZ1
DHAI-0092QSZZ
DHAI-0093QSZZ

PARTS CODE
NO.
1- 12
1- 13
2- 12
2- 10
2- 9
2- 8
1- 10
1- 10
14- 901
15- 12
1- 501
5- 48
1- 7
7- 10
7- 12
11- 501
29- 14
30- 501
17- 901
8- 501
6- 11
6- 10
13- 901
3- 18
1- 3
5- 8
4- 901
5- 2
15- 15
8- 18
11- 25
5- 32
9- 46
4- 13
4- 9
7- 501
30- 7
33- 901
16- 16
28- 901
29- 47
32- 901
19- 901
2- 19
2- 17
27- 901
10- 43
25- 901
21- 901
5- 22
12- 3
20- 901
22- 901
9- 34
23- 901
9- 24
24- 901
9- 40
10- 37
18- 901
5- 501
11- 17
9- 20
17- 37
11- 502
6- 2

AD
AD
AN
AF
AF
AF
BB
BB
BG
AQ
BG
BL
AQ
AH
AH
BK
BL
BL
BS
AE
AG
AN
BA
BA
AM
BR
BB
BB
AF
BA
AF
AL
AG
AH
AH
BU
AU
AU
AV
AV
AZ
AZ
BH
BH
AH
AH
AP
AP
AR
AR
AS
AS
AR
AR
AR
AR
AR
AR
CB
CB
BL
AN
AU
AU
AZ
AQ

2930311729168692223-

AH
AH
AV
AR
BA
BA
AL
AF
AK
AF
AF

11
8
11
10
46
15
4
45
2
1
1

DHAI-0094QSZZ
DHAI-0096QSZZ
DHAI-0100QSZZ
DHAI-0101QSZ1
DHAI-0106QSZZ
DHAI-0108QSZZ
DHAI-0110QSZZ
DHAI-0115QSZZ
DHAI-0116QSZZ
"
DHAI-0120QSZZ
DHAI-0124QSZ2
DHAI-0133QSZZ
DHAI-0140QSZZ
DHAI-0141QSZZ
DHAI-0142QSZ1
DHAI-0143QSZ1
DHAI-0149QSZZ
DHAI-0154QSZZ
DHAI-0184QSZZ
DHAI-0200QSZZ
DHAI-0254QSZZ
DHAI-0309QSZZ
DUNTK0034QSZZ
DUNTK0041RS14
DUNTK0049RS19
DUNTK0050RS31
DUNTW0037RS24
DWIR-0466CSZZ
[G]
GCAB-0013QSZ1
GCAB-0014QSZZ
GCAB-0015QSZZ
GCAB-0017QSZ1
GCAB-0022QSZZ
GCAB-0023QSZ1
GCAB-0024QSZZ
GCAB-0025QSZZ
GCASP0003QSZZ
GCOV-0019QSZ1
GCOV-0020QSZZ
GCOV-0021QSZ1
GCOVH0010QSZ4
GCOVH0011QSZZ
GCOVH0012QSZZ
GCOVH0013QSZ1
GCOVH0014QSZZ
GCOVH0015QSZZ
GCOVH0016QSZZ
GDAI-0002QSZZ
"
GDOR-0001QSZZ
GFTA-0001QSZZ
GFTA-0002QSZZ
GFTA-0007QSZZ
GGAD-0001QSZZ
GGAD-0002QSZZ
GLEGG0064FCZZ
"
[H]
HPNLH0022QSZ3
HPNLH0022QSZ4
HPNLH0024QSZ2
HPNLH0024QSZ3
HPNLH0024QSZ4
HPNLH0024QSZ5
[J]
JBTN-0018QSZZ
JBTN-0020QSZZ
JBTN-0023QSZZ
JBTN-0026QSZZ
JBTN-0027QSZZ
JBTN-0029QSZZ
JBTN-0030QSZZ
JKNBZ0003QSZZ
JKNBZ0005QSZZ
[L]
LBNDJ0013FCZ1
LBNDJ0037FCZ1
"
"

PRICE NEW PART
RANK MARK RANK

N
N

N
N

C
C
C
C
C
C
D
D
E
E
E
D
D
C
C
E
E
E
E
E
E
E
E
E
C
E
E
E
B
C
C
C
B
C
C
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
C
C
C
E
E
C
C
C
C
C
C
C
C
C
C
C

– 32 –

PRICE NEW PART
RANK MARK RANK

NO.
24- 1
21- 1
20- 1
10- 44
6- 24
6- 25
8- 3
2- 21
2- 20
27- 1
5- 9
10- 78
25- 1
10- 50
6- 8
10- 18
10- 18
2- 22
29- 51
7- 3
5- 81
6- 57
8- 5
5- 82
6- 7
10- 9
10- 501
7- 901
13- 7

AF
AF
AG
AL
AL
AK
AP
AF
AC
AC
AG
AY
AH
AP
AP
AQ
AS
AE
AD
AF
AS
AP
AF
BC
BG
BH
CC
BV
BG

C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
E
E
E
E
E
B

1112292930301416161611101102210931191616169-

18
15
23
5
16
15
47
1
18
8
1
24
1
22
2
22
1
1
2
22
12
1
11
6
31
2
3
19
41

BA
AY
AV
AV
AK
AP
AN
AP
AZ
AR
AQ
AM
BC
AP
AS
AL
AR
AG
AH
BH
BH
AW
AW
AD
AE
AE
AE
AC
AC

D
D
D
D
D
D
D
D
D
D
D
D
D
D
C
D
C
D
D
C
C
D
D
D
C
C
C
C
C

222222-

4
4
3
3
3
3

AK
AK
AT
AT
AT
AT

D
D
D
D
D
D

2222222631-

6
11
16
13
15
7
14
41
39

AE
AC
AG
AE
AD
AE
AD
AD
AE

C
C
C
C
C
C
C
C
C

6- 54
20- 2
21- 2
22- 2

AA
AA
AA
AA

C
C
C
C

PARTS CODE
LBNDJ0037FCZ1
"
LBNDJ0043FCZ1
"
LBNDJ2003SCZZ
"
LBOSZ1031FCZZ
"
LBOSZ1508FCZZ
"
"
"
LBOSZ1510FCZZ
"
LBSHZ0006QSZZ
LBSHZ0303FCZZ
"
LDAIU0011QSZZ
LFIX-0009QSZZ
LFIX-0016FCZZ
LFIX-0284FCZZ
LFRM-0016QSZ3
LFRM-0020QSZZ
LFRM-0022QSZZ
LFRM-0023QSZZ
LFRM-0024QSZ3
LFRM-0025QSZ2
LFRM-0026QSZ1
LFRM-0028QSZ1
LFRM-0029QSZ1
LFRM-0030QSZZ
LFRM-0031QSZ2
LFRM-0032QSZ1
LFRM-0036QSZZ
LFRM-0065QSZZ
LFRM-0066QSZZ
LHLDW1226FCZZ
"
LHLDW1263FCZZ
LHLDZ0013QSZZ
LHLDZ0017QSZZ
LHLDZ0030QSZZ
LHLDZ0031QSZ2
LHLDZ0032QSZZ
LHLDZ0033QSZ1
LHLDZ0034QSZZ
LHLDZ0038QSC1
LHLDZ0039QSZZ
LHLDZ0043QSZZ
LHLDZ0044QSZZ
LHLDZ0047QSZ2
LHLDZ0056QSZZ
LHLDZ7021XCZZ
LPINS0007QSZZ
LPINS0181FCZZ
LPLTM0048QSZZ
LPLTM0050QSZZ
LPLTM0053QSZ1
LPLTM0059QSZZ
LPLTM0063QSZ1
LPLTM0064QSZ1
LPLTM0065QSZZ
LPLTM0067QSZZ
LPLTM0070QSZZ
LPLTM0082QSZ5
LPLTM0090QSZZ
LPLTM0091QSZZ
LPLTM0092QSZZ
LPLTM0099QSZ1
LPLTM0109QSZZ
LPLTM0110QSZZ
LPLTM0111QSZZ
LPLTM0112QSZZ
LPLTM0113QSZZ
LPLTM0116QSZZ
LPLTM0125QSZZ
LPLTM0134QSZZ
LPLTM0135QSZZ
LPLTM0136QSZZ
LPLTM0137QSZZ
LPLTM0138QSZZ

NO.
2324105103117911173061117301130951043111010610103130311710712121415314913131337665455561787141310109661033310292929916169101691716-

2
2
42
24
20
12
5
14
9
23
19
33
5
19
48
10
20
33
83
53
11
10
33
14
16
46
23
25
31
35
18
38
21
40
7
20
3
10
19
5
29
6
13
10
15
14
15
21
25
1
84
4
68
47
22
11
17
1
4
38
40
6
22
43
12
8
6
4
24
40
31
45
48
25
5
52
62
30
50
41
31

PRICE NEW PART
RANK MARK RANK

AA
AA
AA
AA
AA
AA
AC
AC
AG
AG
AG
AG
AF
AF
AC
AC
AC
AF
AF
AD
AC
AQ
AV
AP
AQ
BC
AH
AN
AD
AQ
AH
AU
AL
AT
AT
AT
AB
AB
AC
AD
AD
AD
AH
AD
AF
AF
AH
AE
AE
AP
AW
AC
AD
AC
AA
AF
AM
AS
AC
AS
AN
AL
AC
AD
AF
AE
AE
AF
AK
AG
AG
AC
AE
AH
AQ
AD
AD
AF
AD
AD
AD

C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
D
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C

PARTS CODE
LPLTM0302QSZZ
LPLTM2642FCGZ
LPLTP0051QSZZ
LPLTP0056QSZ3
LPLTP0060QSZ3
LPLTP0107QSZZ
LPLTP0108QSZZ
LPLTP0131QSZZ
LPLTP0235QSZ1
LRALM0006QSZZ
LRALM0007QSZZ
LRALP0004QSZ1
LRALP0005QSZ1
LSOU-0009QSZ1
LSOU-0010QSZZ
LSOU-0011QSZZ
LSOU-0013QSZ1
LSOU-0015QSZ1
LSOU-0017QSZ2
LSOU-0018QSZ1
LSTPP0001QSZZ
LSTPP0116FCZZ
LSTPP0161FCZZ
LSUPP0083FCZZ
LX-BZ0004QSZZ
"
LX-BZ0013QSZ1
LX-BZ0015QSZZ
LX-BZ0018QSZZ
LX-BZ0019QSZZ
LX-BZ0020QSZZ
LX-BZ0049FCZZ
LX-BZ0324FCZZ
LX-BZ0335FCZZ
LX-BZ3008SC0M
LX-WZ0001QSZZ
LX-WZ0002QSZZ
LX-WZ0119FCZZ
LX-WZ0144FCZZ
LX-WZ0313FCZZ
LX-WZ0314FCZZ
"
[M]
MARMM0013QSZZ
MARMM0014QSZZ
MARMP0002QSZZ
MARMP0003QSZ1
MARMP0004QSZZ
MARMP0005QSZZ
MARMP0006QSZZ
MARMP0007QSZZ
MARMP0008QSZZ
MARMP0009QSZZ
MARMP0015QSZZ
MARMP0229FCZZ
MCAMP0001QSZZ
MHNG-0009QSZ1
MHNG-0010QSZ1
MLEVF0040QSZZ
MLEVP0010QSZZ
MLEVP0017QSZ1
MLEVP0018QSZ1
MLEVP0019QSZ3
MLEVP0020QSZ3
MLEVP0021QSZZ
MLEVP0022QSZ1
MLEVP0023QSZZ
MLEVP0024QSZZ
MLEVP0025QSZ2
MLEVP0026QSZ2
MLEVP0035QSZ1
MLEVP0037QSZZ
MLEVP0038QSZZ
MLEVP0039QSZ1
MLEVP0044QSZZ
MLEVP0046QSZZ
MLEVP0047QSZ1
MLEVP0090QSZ1
MLOKZ0001QSZZ
MSLI-0138FCZZ
"

– 33 –

NO.

PRICE NEW PART
RANK MARK RANK

614711729293131553911111110292929307141655715910655429785107178-

55
4
23
3
41
3
4
50
3
47
27
2
27
45
48
47
3
1
2
21
5
7
17
4
26
55
30
9
51
79
56
42
41
8
50
55
13
35
58
48
42
37

AC
AD
AD
AD
AM
AH
AH
AD
AD
AG
AG
AH
AN
AR
AU
AL
BA
AV
AP
BF
AD
AA
AB
AB
AB
AB
AC
AF
AB
AD
AB
AB
AA
AA
AA
AC
AB
AA
AA
AA
AA
AA

C
C
C
C
C
C
C
C
C
C
C
C
C
D
D
D
D
D
D
D
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C

3030303030111111111116171129292930777799991272930311791731301645-

42
44
13
4
34
51
20
19
2
16
21
2
22
19
41
44
10
36
33
34
35
39
5
25
32
5
42
9
36
30
35
42
36
51
9
12
7
85

AF
AE
AD
AD
AF
AE
AD
AE
AH
AF
AD
AE
AF
AV
AV
AD
AE
AF
AF
AE
AE
AD
AE
AE
AF
AD
AE
AD
AD
AD
AE
AE
AD
AD
AC
AC
AC
AC

C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
E
E

PARTS CODE
MSPRC0024QSZZ
MSPRC0040QSZZ
MSPRC0062QSZZ
MSPRC0063QSZZ
MSPRC0081QSZZ
MSPRC0082QSZ1
MSPRC0083QSZ1
MSPRC0084QSZ1
MSPRC0085QSZZ
MSPRC0090QSZZ
MSPRC0099QSZ1
MSPRC0101QSZ1
MSPRC0105QSZ1
MSPRC0106QSZZ
MSPRC0115QSZZ
MSPRC0141QSZZ
MSPRC0149QSZZ
MSPRC0152QSZZ
MSPRC0153QSZZ
MSPRC0157QSZZ
MSPRC0161QSZZ
"
MSPRC1145FCZZ
MSPRC1315FCZ1
"
MSPRC1316FCZ1
"
MSPRC1318FCZ1
"
MSPRC2132FCZ1
MSPRC2175FCZZ
MSPRD0092QSZZ
MSPRD0102QSZZ
MSPRD0103QSZZ
MSPRD0104QSZZ
MSPRD0117QSZZ
MSPRD0118QSZ1
MSPRD0121QSZZ
MSPRD0122QSZZ
MSPRD0124QSZZ
MSPRD0125QSZZ
MSPRD0132QSZZ
MSPRD0133QSZZ
MSPRD0134QSZ2
MSPRD0135QSZZ
MSPRD0139QSZZ
MSPRD0140QSZZ
MSPRD0148QSZZ
MSPRD0154QSZZ
MSPRD0156QSZZ
MSPRD0297QSZZ
MSPRP0059QSZZ
MSPRP0060QSZZ
MSPRP0065QSZZ
MSPRP0087QSZZ
MSPRP0123QSZZ
MSPRP0145QSZZ
MSPRP0299QSZZ
MSPRT0066QSZZ
MSPRT0067QSZZ
MSPRT0086QSZZ
MSPRT0089QSZ2
MSPRT0091QSZZ
MSPRT0100QSZZ
MSPRT0128QSZZ
MSPRT0129QSZ1
MSPRT0130QSZ1
MSPRT0147QSZZ
MSPRT0229GCAZ
MSPRT0513FCZ1
[N]
NBLTT0002QSZZ
NBLTT0010QSZZ
NBLTT0011QSZZ
NBRGC0017QSZZ
NBRGC0018QSZZ
NBRGC0133FCZ1
NBRGC0188FCZZ
NBRGC0387FCZ1
NBRGC0529FCZZ
NBRGM0501FCZZ

NO.

PRICE NEW PART
RANK MARK RANK

653131833331499663016291431171791411171130118811116667777292930301716630929171229293172956303077119171617111213-

4
28
4
36
34
16
14
13
9
11
38
30
26
35
33
11
52
15
52
43
6
15
16
7
21
23
18
29
9
23
32
26
14
13
12
43
44
53
52
33
34
41
37
27
18
30
45
35
53
52
11
8
39
32
31
38
86
59
25
14
18
32
12
4
3
23
31
36
17
8

AA
AB
AC
AB
AB
AC
AD
AD
AE
AD
AC
AB
AB
AF
AB
AB
AC
AB
AB
AC
AF
AF
AA
AD
AD
AE
AE
AA
AA
AA
AA
AE
AC
AC
AC
AB
AB
AB
AB
AC
AC
AC
AC
AC
AD
AB
AC
AB
AD
AB
AG
AD
AD
AD
AC
AD
AF
AC
AC
AB
AB
AC
AC
AB
AB
AC
AB
AC
AC
AA

5313131651751717-

37
38
22
29
38
46
17
39
44
9

AH
AG
AG
AC
AD
AC
AB
AC
AD
AB

N

PARTS CODE
NBRGM0501FCZZ
"
NBRGM5006BCZZ
NBRGP0007QSZZ
NBRGP0260FCZ1
NBRGP0567FCZZ
NCPL-0002QSZZ
NCPL-0004FCZZ
NFANP0002QSZ1
NFANP0003QSZ1
NGERH0007QSZZ
NGERH0008QSZ3
NGERH0009QSZZ
NGERH0010QSZZ
NGERH0011QSZZ
NGERH0012QSZZ
NGERH0013QSZZ
NGERH0014QSZZ
NGERH0016QSZZ
NGERH0027QSZZ
NGERH0041QSZZ
NGERH0047QSZZ
NGERH0052QSZZ
NGERH0053QSZZ
NGERH0054QSZZ
NGERH0055QSZZ
NGERH0056QSZZ
NGERH0057QSZZ
NGERH0058QSZZ
NGERH0059QSZZ
NGERH0060QSZZ
NGERH0061QSZZ
NGERH0062QSZZ
NGERH0073QSZZ
NGERH0078QSZZ
NGERH0079QSZZ
NGERH0193FCZZ
"
"
NGERH0495FCZZ
NGERH0540FCZ3
NGERH0972FCZZ
NGERH0990FCZZ
"
NGERH0992FCZZ
NGERH1132FCZZ
NGERH1169FCZZ
"
NGERH1207FCZZ
NGERR0377FCZZ
NKOM-0001QSZZ
NKOM-0002QSZZ
NPLYZ0004QSZZ
NPLYZ0006QSZZ
NPLYZ0010QSZZ
NPLYZ0013QSZZ
NPLYZ0016QSZZ
NPLYZ0017QSZZ
NPLYZ0029QSZZ
NPLYZ0146FCZZ
NROLI0030QSZZ
NROLM0040QSZ1
NROLM0041QSZ1
NROLM0042QSZ1
NROLP0010QSZZ
NROLP0011QSZZ
NROLP0024QSZZ
NROLP0032QSZ2
NROLP0034QSZZ
NROLP0044QSZ2
NROLP1060FCZZ
NROLR0031QSZ1
NROLR0092QSZZ
NROLR0922FCZZ
"
NSFTZ0009QSZZ
NSFTZ0011QSZZ
NSFTZ0013QSZZ
NSFTZ0017QSZZ
NSFTZ0018QSZ1
NSFTZ0021QSZ1

C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
B
B
C
C
C
C
C
C
C

– 34 –

NO.
2931129776812108888888885173188888888911630931111429117111730301716917296125530554123173131312929306121716712113029302911116-

29
25
8
19
28
8
3
24
12
6
26
28
20
19
22
30
32
21
33
34
28
23
25
14
38
35
36
27
31
29
17
15
37
16
44
26
46
14
7
14
13
27
29
28
30
8
13
45
1
5
29
19
40
19
23
43
18
4
9
37
11
40
6
43
36
26
27
40
18
13
22
27
4
13
31
37
32
28
21
11
28

PRICE NEW PART
RANK MARK RANK

AB
AB
AB
AD
AD
AG
AC
AB
AX
AY
AH
AL
AD
AD
AD
AE
AG
AD
AD
AH
AF
AF
AE
AD
AD
AE
AE
AE
AF
AD
AH
AD
AK
AE
AE
AD
AB
AB
AB
AC
AD
AB
AB
AB
AB
AH
AF
AF
AF
AD
AD
AC
AG
AD
AE
AL
AF
AE
AD
AB
BC
AS
AR
AR
AD
AD
AL
AT
AD
AQ
AF
BC
AM
AR
AR
AE
AG
AF
AG
AL
AL

C
C
C
C
C
C
C
C
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C

PARTS CODE
NSFTZ0028QSZZ
NSFTZ0030QSZZ
NSFTZ0032QSZZ
[P]
PBRSR0004QSZ1
PBRSS0008QSZ1
PBRSS0026QSZZ
PCAPH0011QSZZ
PCASZ0006QSZZ
PCASZ0008QSZZ
PCLC-0016QSZZ
PCOVP0029QSZ2
PCOVP0030QSZZ
PCOVP0032QSZ1
PCOVP0033QSZZ
PCOVP0039QSZ2
PCUSF0334FCZZ
PCUSG0018QSZZ
PCUSG0019QSZZ
PCUSS0009QSZZ
PCUSS0011QSZZ
PCUSS0013QSZ3
PCUSS0201FCZZ
PCUSU0203FCZZ
PFILZ0004QSZZ
PGIDH0031QSZZ
PGIDH0033QSZ1
PGIDH0044QSZZ
PGIDH0046QSZ1
PGIDM0030QSZZ
PGIDM0032QSZZ
PGIDM0034QSZ2
PGIDM0035QSZZ
PGIDM0036QSZZ
PGIDM0037QSZZ
PGIDM0038QSZZ
PGIDM0043QSZ1
PGIDM0045QSZ5
PGIDM0047QSZZ
PGIDM0048QSZ1
PGIDM0049QSZ1
PGIDM0050QSZ1
PGIDM0054QSZ1
PGIDM0055QSZZ
PGIDM0062QSZZ
PGLSP0003QSZZ
PGLSP0004QSZZ
PGUMS0002QSZZ
PGUMS0004QSZZ
PMIR-0008QSZZ
PMIR-0009QSZZ
PMLT-0027QSZZ
PMLT-0032QSZZ
PMLT-0033QSZZ
PMLT-0034QSZZ
PMLT-0035QSZZ
PPIPP0006QSZZ
PPIPP0007QSZZ
PPIPP0008QSZZ
PPIPP0009QSZZ
PPIPP0011QSZZ
PPIPP0109FCZZ
"
PPIPP0174FCZZ
PREFL0004QSZZ
PRNGP0019FCZZ
PSHEP0050QSZ1
PSHEP0051QSZZ
PSHEP0052QSZZ
PSHEP0053QSZ4
PSHEP0085QSZZ
"
PSHEP3029FCZZ
PSHEZ0054QSZ1
PSHEZ0056QSZZ
PSHEZ0058QSZ1
PSHEZ0059QSZZ
PSHEZ0068QSZZ
PSHEZ0069QSZZ
PSHEZ0070QSZZ
PSHEZ0071QSZZ

NO.

PRICE NEW PART
RANK MARK RANK

5- 44
29- 35
30- 21

AM
AL
AH

C
C
C

7311211353171199295224129451213731318137141411113131301616161112115545121555917301117111765161313137105311461129293131-

AD
AH
AF
AC
AM
AM
AU
AT
AN
AD
AF
AQ
AP
AD
AC
AA
AB
AZ
AA
AE
AM
AH
AK
AK
AK
AL
AE
AL
AP
AP
AG
AG
AQ
AN
AP
AW
AV
AN
AG
AG
AP
BA
AX
AL
AA
AP
AS
AC
AC
AC
AC
AB
AD
AD
AD
AD
AC
AB
AB
AC
AP
AA
AD
AB
AB
AH
AC
AC
AA
AC
AC
AU
AF
AC
AE
AG
AE

C
B
B
C
C
C
B
C
C
C
C
C
C
C
C
C
C
C
C
C
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
B
C
C
B
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C

50
7
1
29
12
7
28
5
1
37
26
12
87
31
32
10
50
22
14
88
14
2
25
41
8
1
16
20
5
9
41
42
33
5
46
10
9
20
19
21
16
8
51
33
21
12
89
15
41
56
57
63
16
7
17
24
45
6
20
34
90
14
3
5
9
24
66
51
21
2
49
2
9
42
43
42
44

PARTS CODE
PSHEZ0077QSZ1
PSHEZ0078QSZZ
PSHEZ0089QSZZ
PSHEZ0099QSZZ
PSHEZ0100QSZZ
PSHEZ0105QSZZ
PSHEZ0108QSZZ
PSHEZ0109QSZZ
"
PSHEZ0122QSZ2
PSHEZ0123QSZ2
PSHEZ0124QSZ1
PSHEZ0125QSZZ
PSHEZ0131QSZZ
PSHEZ0133QSZZ
PSHEZ0135QSZZ
PSHEZ0136QSZZ
PSHEZ0137QSZZ
PSHEZ0140QSZZ
PSHEZ0152QSZZ
PSHEZ0160QSZZ
PSHEZ0162QSZZ
PSHEZ0171QSZZ
PSHEZ0172QSZZ
PSHEZ0173QSZZ
PSHEZ0196QSZ1
PSHEZ0238QSZZ
PSHEZ0252QSZZ
PSHEZ0399QSZZ
PSHEZ2026FCZZ
PSHEZ2174FCZZ
PSHEZ7242XCZZ
PSPAZ0011QSZZ
PSPAZ0018QSZZ
PSPAZ0022QSZZ
PSPAZ0024QSZZ
PSPO-0001QSZZ
PSPO-0002QSZZ
PSPO-0005QSZZ
PSPO-0007QSZZ
PSPO-0008QSZZ
PSPO-0009QSZZ
PSPO-0010QSZZ
PSPO-0011QSZZ
PSPO-0014QSZZ
PTME-0003QSZ1
PTME-0012QSZZ
PTME-0013QSZZ
PTME-0014QSZZ
PTME-0015QSZZ
PTME-0016QSZZ
PTME-0017QSZZ
PTME-0019QSZZ
PTME-0020GCZ1
"
PTME-0022QSZ1
PTME-0023QSZ1
PTME-0178FCZZ
PTME-0179FCZZ
PTPE-0010QSZZ
PTPE-0015QSZZ
PTPE-0017QSZZ
PTPE-0018QSZZ
PWIR-0005QSZ1
PWIR-0006QSZZ
[Q]
QCNCM0017QSZZ
QCNCM0019QSZZ
QCNCM0029QSZZ
QCNCM0060QS06
QCNCM0877FCZZ
"
QCNCM0923FC16
QCNCM0923FC22
"
"
QCNCM0923FC24
"
QCNCM0999FCZZ
QCNCM1003FCZZ
QCNCM1004FCZZ

– 35 –

NO.
2929111117510511113291010210553116161697312931314514929301717161616161688973117173077141411111163155-

PRICE NEW PART
RANK MARK RANK

23
25
28
35
37
46
52
67
53
52
57
56
19
29
23
64
61
28
97
58
71
54
40
33
34
54
56
55
34
28
1
2
15
72
20
55
27
2
53
54
35
36
37
38
39
8
15
3
51
34
32
30
26
19
37
6
10
31
30
53
54
50
47
1
12

AE
AF
AF
AC
AC
AC
AC
AC
AC
AB
AA
AB
AE
AG
AD
AC
AC
AH
AE
AD
AE
AB
AD
AB
AB
AD
AC
AF
AB
AB
AB
AE
AD
AE
AC
AB
AB
AC
AA
AB
AC
AD
AD
AD
AG
AD
AC
AL
AK
AD
AD
AD
AD
AF
AF
AL
AL
AC
AC
AC
AC
AA
AC
AQ
AQ

C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C

18- 2
18- 9
25- 2
18- 106
18- 3
28- 1
28- 2
18- 11
28- 3
32- 1
18- 4
32- 2
31- 17
31- 15
31- 16

AC
AB
AK
AB
AF
AF
AF
AF
AF
AF
AF
AF
AC
AD
AD

C
C
C
C
C
C
C
C
C
C
C
C
C
C
C

PARTS CODE
QCNCM1005MCZZ
QCNCM1006MCZZ
QCNCM1119LC0C
QCNCM1119LC0D
QCNCM2401SC0C
QCNCM2401SC0D
QCNCM2401SC0E
QCNCM7014SC0B
"
QCNCM7014SC0C
"
QCNCM7014SC0D
QCNCM7014SC0F
QCNCM7014SC0G
"
"
QCNCM7014SC1B
QCNCP0240QCZZ
QCNCP0242QCZZ
QCNCP0341QCZZ
QCNCW0015QSZZ
QCNCW0020QSZZ
QCNCW0022QSZZ
"
QCNCW0024QSZZ
QCNCW0885FCZZ
QCNCW0948FCZ3
QCNCW1124LC0D
QCNCW1124LC0H
QCNCW7191RC1B
QSLP-0008QSZZ
QSLP-0009QSZZ
QSOCZ0002QSZZ
QSW-B0003QSZZ
"
"
QSW-P0008QSZZ
"
QTANN0015FCZZ
[R]
RCORF0002QSZZ
"
RCORF0005QSZZ
RCORF0006QSZZ
"
"
RCORF0026FCZZ
RCORF2037SCZZ
RCORF6661RCZZ
RCRMZ0001QSZZ
RCRSP0016QSZZ
RCRUB0009QSZZ
RCRUB0010QSZZ
RDENC0008QSZZ
RDENC0009QSZZ
"
RDTCT0005QSZZ
RDTCT0006QSZZ
RFILN0019GCZZ
RH-IX0009QSZZ
RH-IX0013QSZZ
RLMPU0012QSZZ
RLMPU0016QSZZ
RMOTD0016QSZ1
RMOTP0020QSZZ
RMOTP0021QSZ1
RMOTP0039QSZZ
RMPTW4000QCJJ
RMPTW4103QCJJ
RMPTW4203QCJJ
RMPTW4222QCJJ
RMPTW4330QCJJ
RPLU-0004QSZ1
RPLU-0007QSZZ
RPLU-0008QSZZ
RPLU-0009QSZZ
RPLU-0012QSZZ
RPLU-0013QSZZ
RTHM-0001QSZZ
[S]
SPAKA0083RSZZ

PRICE NEW PART
RANK MARK RANK

NO.
18- 12
18- 13
18- 14
18- 15
18- 16
18- 5
18- 17
18- 18
32- 3
18- 19
32- 4
18- 20
18- 21
18- 22
32- 5
33- 1
18- 23
18- 24
18- 107
18- 25
18- 26
19- 1
19- 2
27- 2
18- 27
18- 6
18- 28
18- 29
18- 30
18- 10
13- 14
13- 11
18- 108
17- 26
6- 44
9- 1
19- 3
27- 3
10- 49

AB
AB
AC
AC
AB
AC
AC
AD
AD
AA
AA
AB
AB
AB
AB
AB
AD
AA
AA
AC
AE
AG
AE
AE
AF
AG
AC
AB
AC
AG
AD
AD
AD
AF
AF
AF
AC
AC
AG

C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
B
B
B
B
C

5- 59
5- 79
2- 33
10- 96
16- 32
17- 49
29- 56
10- 80
31- 48
19- 4
18- 31
18- 32
18- 33
10- 11
10- 8
26- 901
7- 16
31- 35
18- 34
18- 74
18- 109
5- 91
7- 6
6- 5
31- 13
5- 30
8- 7
18- 35
18- 36
18- 37
18- 38
18- 39
30- 11
11- 28
8- 16
8- 10
17- 16
17- 33
7- 2

AE
AE
AH
AL
AL
AL
AL
AH
AK
AE
AD
AP
AP
BN
BK
BK
AN
AL
AC
AP
AU
BG
BA
AZ
BC
BC
BF
AB
AB
AA
AB
AB
AQ
AN
AN
AN
AN
AN
AM

C
C
C
C
C
C
C
C
C
B
B
B
B
E
E
E
B
B
C
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B

15-

AD

D

4

PARTS CODE
SPAKA0120RSZZ
SPAKA0134QSZZ
SPAKA0150RSZZ
SPAKA0167RSZZ
SPAKC0145RS23
SPAKC0416RS11
SSAKA2343QCZZ
SSAKZ0003QSZZ
[T]
TCADZ0010QSZZ
TCAUA0770FCZZ
TCAUH0007QSZZ
TINSE0854QSZZ
TINSG0847QSZZ
TLABH0062QSZZ
TLABH0064QSZ1
TLABH0065QSZ1
TLABH0065QSZZ
TLABH0068QSZ1
TLABH0124QSZZ
TLABH0138QSZZ
TLABH0388QSZ1
TLABS3760FCZZ
TLABZ0058QSZZ
TTAG-0004QSZZ
"
[U]
UBAGF0018YSZ1
[V]
VCCCCY1HH101J
VCCCCY1HH120J
VCCCCY1HH300J
VCCCCY1HH7R0D
VCCUCY1AJ105Z
"
VCEAGA1HW107M
VCEAGA1VW106M
"
VCEAGU1CW106M
VCEAGU1CW107M
VCEAGU1CW226M
VCEAGU1CW476M
VCEAGU1VW476M
"
"
VCEAJU1CW476M
VCKYCY1EB223K
VCKYCY1EF104Z
"
VCKYCY1HB102K
"
VCKYCY1HB222K
VCKYCY1HB471K
VCKYCY1HF103Z
VCKYCY1HF223Z
VCKYPU1HB102K
"
"
"
"
"
VCKYPU1HF223Z
VCKYTV1HB102K
VCKYTV1HB222K
"
VCKYTV1HB471K
VCKYTV1HF104Z
"
VHD1N4005E/-1
VHDDAN202K/-1
VHDDAP202K/-1
VHDDSS133//-1
"
"
VHERD20EB3/-1
VHEUDZS5.6B-1
VHI27C00401QS
VHI29F04027QS
VHI65808GN146
VHI74HCT244MF
VHI74LS244NS1

– 36 –

PRICE NEW PART
RANK MARK RANK

NO.
15- 4
15- 7
15- 17
15- 21
15- 1
15- 1
15- 19
15- 5

BS
AE
AA
AA
BU
BU
AA
AF

N

1516151571415151531511511415-

8
46
53
18
18
39
8
13
13
18
20
18
44
22
49
19
11

AC
AB
AD
AY
AY
AE
AC
AG
AN
AF
AC
AD
AG
AC
AD
AC
AC

D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D

15-

6

AF

D

18181918181918183218181818182832191818191819181819192021222324283332283232283218282818193218181818181818-

40
41
5
42
43
9
48
49
6
44
45
46
47
50
4
7
6
51
52
26
53
7
54
55
8
10
3
3
3
3
3
15
2
8
5
9
10
6
11
57
7
8
56
11
12
58
59
64
1
76
77
78

AA
AA
AB
AA
AC
AC
AA
AA
AA
AA
AB
AA
AB
AB
AB
AB
AB
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AB
AB
AA
AA
AA
AB
AC
AM
AW
BF
AH
AH

C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
B
B
B
B
B
B
B
B
B
B
B
B

N
N

N

D
D
D
D
D
D
D
D

PARTS CODE
VHI74VHC08/-1
VHIH8/3643/-1
VHIH8S/2350FP
VHIHG73C025FD
VHILM358PS/-S
VHIM66236FP-1
VHIMC7805CT-1
VHINJM2103M-1
VHINJM2903M/VHINJM3414M-1
VHISC65165V6T
VHISLA7027MUL
"
VHITA7291S/-1
VHITB62706AN/
VHITC74ACT32F
VHITC74HC151F
"
VHITD62503F/VHITD62785F//
VHIULN2003AN1
"
"
VHIW42C3103G/
VHP1LHEE-002A
VHP1LHLE-002A
"
VHPGP1A71A1-1
"
"
VHPGP1S53V/-1
"
"
"
"
VHPGP1S58V/-1
VHPLTC3650G01
VHVICPN38//-1
"
"
VRD-HT2EY121J
VRD-HT2EY241J
VRD-RC2EY161J
VRH-ST2HB157K
VRS-CY1JD000J
"
VRS-CY1JD100J
VRS-CY1JD101J
VRS-CY1JD102J
VRS-CY1JD103F
VRS-CY1JD103J
"
VRS-CY1JD105J
VRS-CY1JD123J
VRS-CY1JD203J
VRS-CY1JD205J
VRS-CY1JD220F
VRS-CY1JD221J
VRS-CY1JD242F
VRS-CY1JD242J
VRS-CY1JD301J
VRS-CY1JD330J
VRS-CY1JD331J
VRS-CY1JD471J
VRS-CY1JD472J
VRS-CY1JD473J
VRS-CY1JD511J
VRS-CY1JD680J
VRS-HT3AA1R5J
VRS-RE3DA131J
VRS-RE3DA1R0J
VRS-TP2BD000J
"
VRS-TP2BD221J
"
VRS-TP2BD472J
VRS-TP2BD473J
VRS-TP2BD6R8J
VRS-TS2AD101J
VRS-TS2AD103J
"

NO.
18- 79
19- 12
18- 61
18- 60
18- 62
18- 66
18- 63
18- 65
18- 67
18- 68
18- 7
18- 69
32- 13
18- 70
19- 13
18- 71
28- 9
32- 14
18- 72
19- 14
18- 73
28- 10
32- 15
18- 75
19- 17
19- 16
27- 4
17- 15
29- 10
31- 53
20- 4
21- 4
22- 4
23- 4
24- 4
33- 3
19- 15
18- 8
28- 11
32- 16
33- 4
33- 5
19- 18
7- 49
18- 80
19- 19
18- 81
18- 82
18- 83
18- 84
18- 85
19- 20
19- 21
19- 22
18- 86
18- 87
18- 88
18- 89
18- 90
18- 91
18- 110
18- 92
18- 93
19- 23
18- 94
18- 95
18- 96
18- 97
32- 17
18- 99
18- 98
28- 12
32- 18
18- 100
32- 19
18- 101
18- 102
19- 24
18- 103
28- 13
32- 20

PRICE NEW PART
RANK MARK RANK

AE
AU
AY
BE
AC
AT
AD
AH
AD
AF
BW
AQ
AQ
AF
AS
AF
AG
AG
AG
AN
AE
AE
AE
AU
AC
AC
AC
AG
AG
AG
AE
AE
AE
AE
AE
AE
AQ
AF
AF
AF
AA
AA
AA
AD
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AC
AB
AA
AA
AB
AB
AA
AA
AA
AA
AA
AA

B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C

PARTS CODE
VRS-TS2AD152J
VRS-TS2AD242J
VRS-TS2AD473J
VRS-TS2AD912J
VS2SA1036KQRC
VS2SA1162-Y-1
VSDTC114EK/-1
[X]
XBBSD30P04000
XBBSD30P05000
"
XBBSD30P06000
"
XBBSD30P08000
XBBSD30P10000
XBBSD40P10000
XBBSE30P06000
"
"
XBPSC30P06ES0
XBPSD30P05K00
XBPSD30P05KS0
"
XBPSD30P08KS0
"
XBPSD30P10KS0
"
XBPSD30P30KS0
XBPSD40P06K00
XBPSD40P06KS0
XBPSD40P16KS0
XBPSN40P06K00
XEBSD20P06000
XEBSD30P06000
"
"
"
"
XEBSD30P08000
"
"
"
"
"
"
"
XEBSD30P10000
"
"
"
"
XEBSD30P18000
XEBSD40P06000
"
XEBSD40P12000
"
"
XEBSE30P08000
"
"
"
"
"
"
"
XEBSE40P10000
"
"
XEBSE40P12000
"
"
XEBSE40P14000
"
XEPSD23P12000
XEPSD30P08X00
"
"
XEPSD40P12000
XEPSD40P30000
XHBSD30P04000
XHBSD30P06000

– 37 –

NO.

PRICE NEW PART
RANK MARK RANK

32- 21
32- 22
32- 23
32- 24
18- 105
19- 25
18- 104

AA
AA
AA
AA
AB
AB
AB

C
C
C
C
B
B
B

817316751181011765307107671054510121356671111121425691031366104510109101113293030313111116299299611629910510-

AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA

C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C

17
34
14
58
22
23
34
6
39
16
46
9
29
12
1
10
9
42
15
7
5
3
31
17
13
17
93
23
31
21
18
52
2
12
18
94
16
11
27
46
7
18
6
46
6
95
15
55
22
4
43
1
24
43
6
45
9
14
24
4
7
20
47
55
49
1
26
27
6
7
54
54
13

PARTS CODE
XHBSD30P06000
"
"
"
XHBSD30P08000
"
XHBSD30P10000
XHBSD30P14000
"
XHBSD30P16000
XHBSE30P08000
"
"
"
XHBSE30P10000
XHBSE40P10000
XHPSD30P08X00
XPSSJ20-07000
"
XPSSJ30-12000
XPSSP20-07000
XPSSP20-09000
XRESP20-04000
XRESP30-06000
"
XRESP40-05000
XRESP40-06000
"
"
"
"
"
"
"
XRESP50-06000
"
"
"
"
"
XRESP60-08000
XRESP70-08000
"
XWHSD30-05070
XWHSD30-05080
XWHSD30-08100
XWHSD40-08100
"
XWHSD60-10000
XWSSD30-07000
XWSSD40-10000
XWVSD40-05000
[0]
0AV1390000107
0AV1390000108
0AV1390000110
0AV1390000177
0AV1390000181
0AV1390000184
0AV1390000198
0AV1480000079
0AV1480000083
0AV1560000002
0AV1560000005
0AV1610000091
0AV1610000108
0AV1610000109
0AV1610000114
0AV1690000088
0AV1690000106
0AV1690000111
0AV2011003020
0AV2011013010
0AV2011023010
0AV2011033010
0AV2011033030
0AV2011043030
0AV2011213030
0AV2011223030
0AV2011543020
0AV2011833010

NO.

PRICE NEW PART
RANK MARK RANK

156710831033101012916161116530312930751114173031689121717315965971014101017101029-

20
6
52
4
29
2
3
26
5
11
5
63
17
32
28
29
38
8
36
45
29
24
54
24
29
20
4
7
18
15
27
27
12
13
10
4
47
20
38
18
39
36
43
54
48
13
57
65
48
47
56
48

AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA

C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C

26262626262626262626262626262626262626262626262626262626-

10
12
15
13
14
9
7
6
5
3
17
8
11
16
18
2
1
4
45
50
54
48
56
42
40
61
43
57

AC
AC
AF
AC
AE
AC
AR
AC
AC
AD
AH
AC
AD
AC
AD
AC
AD
AD
AA
AA
AA
AA
AB
AA
AB
AB
AC
AA

C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C

PARTS CODE
0AV2012203010
0AV2012243020
0AV2013333010
0AV2014713010
0AV2014723010
0AV2014733010
0AV2014733030
0AV2015633010
0AV2016803030
0AV2016833010
0AV2021043062
0AV2041013020
0AV2041213030
0AV2043303010
0AV2091083042
0AV2990007000
0AV3001015090
0AV3020143999
0AV3021815090
0AV3042605000
0AV3050019000
0AV3050036000
0AV3050086000
0AV3050097000
0AV3050098000
0AV3050099000
0AV3060027000
0AV3060043000
0AV3060044000
0AV3070056000
0AV3070057000
0AV3070058000
0AV3070074000
0AV3070081000
0AV3070085000
0AV3082561300
0AV3090076000
0AV3090077000
0AV3090080000
0AV3090081000
0AV3160034000
0AV3180000004
0AV4000135411
0AV4070062000
0AV4070065000
0AV4080010000
0AV4120002000
0AV4120013000
0AV5030126000
0AV5030132000
0AV5030133000
0AV5030134000
0AV5030135000
0AV5030136000
0AV5050005000
0AV5060083000
0AV5060085000
0AV5060092000
0AV5080010000
0AV5110001000
0AV5110002000
0AV5110004000
0AV5110012000
0AV5130008000
0AV5140022000
0AV5190009000
0AV5190024000
0AV6114125811
0AV7100003000
0AV7414138611
0AV8117730414
0AV8117730514

– 38 –

NO.
26- 63
26- 55
26- 44
26- 60
26- 58
26- 62
26- 38
26- 53
26- 52
26- 49
26- 51
26- 39
26- 41
26- 47
26- 46
26- 59
26- 35
26- 36
26- 37
26- 34
26- 24
26- 23
26- 19
26- 27
26- 29
26- 28
26- 20
26- 21
26- 33
26- 26
26- 30
26- 22
26- 31
26- 32
26- 25
26- 74
26- 75
26- 76
26- 77
26- 78
26- 70
26- 73
26- 69
26- 64
26- 68
26- 66
26- 65
26- 67
26- 79
26- 80
26- 81
26- 82
26- 83
26- 84
26- 89
26- 87
26- 86
26- 88
26- 85
26- 97
26- 98
26- 99
26- 96
26- 90
26- 71
26- 72
26- 100
26- 92
26- 91
26- 95
26- 93
26- 94

PRICE NEW PART
RANK MARK RANK

AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AD
AC
AC
AB
AC
AC
AD
AD
AC
AN
AF
AF
AB
AG
AG
AD
AH
AC
AC
AD
AC
AC
AC
AC
AC
AF
AF
AN
AN
AL
AQ
AL
BD
AF
AQ
AP
AC
AC
AG
AL
AF
AL
AG
AC
AA
AF
AF
AE
AQ
AA
AA
AA
AB
AC
AF
AL
AK
AF
AE
AD
AB
AB

C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
C
C
C
C
C
C
C
C
C
C
C
C
A
A
A
B
C
C
C
C
B
B
B
B
C
C
D
C
C

CAUTION FOR BATTERY REPLACEMENT
(Danish)
ADVARSEL !
Lithiumbatteri-Eksplosionsfare ved fejlagtig håndtering.
Udskiftning må kun ske med batteri
af samme fabrikat og type.
Levér det brugte batteri tilbage til leverandoren.
(English)
Caution !
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type
recommended by the manufacturer.
Despose of used batteries according to manufacturer's instructions.
(Finnish)
VAROITUS
Paristo voi räjähtää, jos se on virheellisesti asennettu.
Vaihda paristo ainoastaan laitevalmistajan suosittelemaan
tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden
mukaisesti.
(French)
ATTENTION
Il y a danger d'explosion s' il y a remplacement incorrect
de la batterie. Remplacer uniquement avec une batterie du
même type ou d'un type équivalent recommandé par
le constructeur.
Mettre au rébut les batteries usagées conformément aux
instructions du fabricant.
(Swedish)

VARNING
Explosionsfare vid felaktigt batteribyte.
Använd samma batterityp eller en ekvivalent
typ som rekommenderas av apparattillverkaren.
Kassera använt batteri enligt fabrikantens
instruktion.

(German)
Achtung
Explosionsgefahr bei Verwendung inkorrekter Batterien.
Als Ersatzbatterien düen nur Batterien vom gleichen Typ oder
vom Hersteller empfohlene Batterien verwendet werden.
Entsorgung der gebrauchten Batterien nur nach den vom
Hersteller angegebenen Anwerisugen.

CAUTION FOR BATTERY DISPOSAL
(For USA,CANADA)
Contains lithium-ion battery. Must be disposed of properly.
Remove the battery from the product and contact
federal or state environmental
agencies for information on recycling and disposal options.

q

COPYRIGHT  2002 BY SHARP CORPORATION
All rights reserved.
Printed in Japan.
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted.
In any form or by any means,
electronic, mechanical, photocopying, recording, or otherwise,
without prior written permission of the publisher.

Trademark acknowledgments
Microsoft and Windows are trademarks of Microsoft Corporation in the U.S.A and other
countries.
IBM and PC/AT are trademarks of International Business Machines Corporation.
Adobe and Acrobat are trademarks of Adobe Systems Incorporated.
All other trademarks and copyrights are the property of their respective owners.

SHARP CORPORATION
Digital Document Systems Group
Products Quality Assurance Department
Yamatokoriyama, Nara 639-1186, Japan

2002 November Printed in Japan t