Toshiba Printer B EV4 BEV4 Set Tool 7th
User Manual: Toshiba Printer B-EV4
Open the PDF directly: View PDF 
.
Page Count: 16
| Download | |
| Open PDF In Browser | View PDF |
TOSHIBA Bar Code Printer
B-EV4 Series
Printer Setting Tool Operating Specification
1st edition:
2nd edition:
3rd edition:
4th edition:
5th edition:
6th edition:
7th edition:
January 5, 2009
May 29, 2009
June 18, 2009
July 22, 2009
August 21, 2009
February 4, 2010
April 6, 2010
B-EV4 Series Printer Setting Tool Operating Specification
TABLE OF CONTENTS
1. SCOPE ....................................................................................................................................... 1
2. GENERAL DESCRIPTION ........................................................................................................ 1
3. SYSTEM REQUIREMENT ......................................................................................................... 1
4. SETTING TOOL MAIN SCREEN............................................................................................... 2
5. PARAMETER SETTING PAGE ................................................................................................. 7
6. MAINTENANCE MODE PAGE ................................................................................................ 11
7. EXTRA SETTING PAGE.......................................................................................................... 12
8. FACTORY DEFAULT SETTING BY FIRMWARE VERSIONS................................................ 14
Copyright © 2008
by TOSHIBA TEC CORPORATION
All Rights Reserved
570 Ohito, Izunokuni-shi, Shizuoka-ken, JAPAN
B-EV4 Series Printer Setting Tool Operating Specification
1. SCOPE
This specification applies to the operations of the software for setting the printer parameters,
communication conditions, and performing a sensor calibration of the B-EV4 series general-purpose bar
code printer.
2. GENERAL DESCRIPTION
Since the B-EV4 series has no LCD, it does not support the system mode equivalent to the one
provided for the other TOSHIBA TEC bar code printers. Accordingly, setting the printer parameters,
implementing the maintenance features, and downloading these settings to the printer are executed on
a PC by using a setting tool.
This specification describes the functions and operation of the setting tool.
3. SYSTEM REQUIREMENT
• System:
• Interface:
• Memory:
• Hard disk free space:
DOS/V computer running Windows 2000, Windows XP, or Windows Vista
(Operations under the other OS are not guaranteed.)
USB, RS232C, Centronics, or LAN
128 MB or more
10MB or more
Windows is a registered trademark of Microsoft Corporation in the United States and other countries.
-1-
B-EV4 Series Printer Setting Tool Operating Specification
4. SETTING TOOL MAIN SCREEN
DO NOT get the printer status ([Get Status]), upload ([Read]) or download ([Set]) the
settings from/to the printer while the printer is in operation (during printing or
communicating with the host).
gFile menu
h About menu
c
e
d
f
i
l
j
k
11
Note: The values shown in the initial screens displayed when the setting tool is started are not the
factory default settings. For the factory default settings, see Section 8 Factory Default Setting by
Firmware Versions.
-2-
B-EV4 Series Printer Setting Tool Operating Specification
c
Get Status
When the [Get Status] button is clicked, the current printer status is obtained via the selected interface.
The printer status is indicated by the following message and displayed in the box of the main screen.
Note: This function cannot be used with the parallel interface.
Status Message List
Message
ON LINE
HEAD OPEN
PAUSE
COMMS ERROR
PAPER JAM
CUTTER ERROR
NO PAPER
HEAD OPEN
EXCESS MOTOR TEMP
EXCESS HEAD TEMP
RIBBON ERROR
SAVING
FLASH WRITE ERR.
FORMAT ERROR
FLASH CARD FULL
COMMAND ERROR
d
Printer status
Online mode
The top cover is opened in the online mode.
Pause state
A parity, overrun, or framing error has occurred during communication
through the RS-232C.
The media was jammed during paper feed.
A problem has occurred with the cutter module.
The media has run out.
Feed or printing was attempted with the top cover opened.
The stepping motor temperature has become excessively high.
The print head is overheated.
The ribbon has run out.
Ribbon motor sensor detected an abnormal state.
Writable character or PC command save mode
An error has occurred while writing data to the SD card.
An error has occurred in formatting the SD card.
Data cannot be stored because the SD card is full.
A command error has occurred in analyzing the command.
Language
Select a language to show the setting tool screen.
The default language is depending on the OS.
e
Interface
Select a type of interface to be used for downloading or uploading the printer settings between the PC
(printer setting tool) and the printer.
USB, COM (Serial), LPT (Parallel), or ETHERNET (LAN) can be selected.
-3-
B-EV4 Series Printer Setting Tool Operating Specification
• When the COM (Serial) is selected, click on the [Setup] button and configure the communication
settings in accordance with the printer’s communication conditions.
COM Port:
Baud Rate:
Data Bits:
Parity Check:
Stop Bit(s):
Hardware Handshaking:
Software Handshaking:
COM 1 to COM 30
2400, 4800, 9600, 19200, 38400, 57600, or 115200
7or 8
None, Odd, Even
1, 1.5, or 2
None, RTS, or RTS/CTS
None or Xon/Xoff
• When the LPT (Parallel) is selected, click on the [Setup] button and select an LPT port No.
• When the ETHERNET (LAN) is selected, click on the [Setup] button and set a printer IP address
and a socket port number.
-4-
B-EV4 Series Printer Setting Tool Operating Specification
f
Printer Version
Select a printer firmware version. According to the selected printer version, the non-programmable
parameters are grayed out.
When the printer is connected via USB, the firmware version is automatically read and displayed at a
power on time.
When any other interface than USB is selected, manually select the firmware version of the connected
printer.
How to check the printer firmware version (Diag. test print)
1. Turn off the printer power and install a media roll (and ribbon) on the printer.
2. Press and hold down the [FEED] button while turning on the printer. The Indicator Lamp will
light up in the following order:
Green (Flashing) → Red (Flashing) → Orange (Flashing) → Orange → RED → Green
3. Release the [FEED] button when the Indicator Lamp lights up in green.
4. The printer automatically performs a diag. test printing, and then enters the Dump Mode.
PRINTER INFO.
PROGRAM VERSION
TONE ADJUST
FEED ADJUST
CUT POSITION ADJUST
BACKFEED ADJUST
PARAMETER
VX.XX XXXX
+XX
+XX.Xmm
+XX.Xmm
+XX.Xmm
[ PC-850 ] [ 0 ]
[ 9600 ] [ 8 ] [ 1 ] [ NONE ] [ 2 ]
[ ON ] [ AUTO ] [ FEED ] [ B0 ]
5. To start the Online operation, turn the printer off, then on again.
g
File menu
Only the Exit menu is provided.
-5-
Firmware version and checksum
B-EV4 Series Printer Setting Tool Operating Specification
h
About menu
The version of the printer setting tool is displayed.
i
Parameter Setting tab
When the Parameter Setting tab is clicked, the Parameter Setting page is displayed.
For details of the Parameter Setting page, refer to Section 5.
j
Maintenance Mode tab
When the Maintenance Mode tab is clicked, the Maintenance Mode page is displayed.
For details of the Maintenance Mode page, refer to Section 6.
k
Extra Setting tab
When the Extra Setting tab is clicked, the Extra Setting page is displayed.
For details of the Extra Setting page, refer to Section 7.
l
LPT port No.
The currently selected LPT port No. is displayed.
11
Serial interface settings
The currently selected serial interface settings are displayed.
-6-
B-EV4 Series Printer Setting Tool Operating Specification
5. PARAMETER SETTING PAGE
g
c
e
d
f
Note: According to the selected printer version, the non-programmable parameters are grayed out.
c
Load
When the [Load] button is clicked, the parameter settings and fine adjustment value are loaded from a
specified setup file.
Note: This function is used to download the same settings to other printers.
d
Save
When the [Save] button is clicked, the configured parameter settings and fine adjustment value,
displayed on the screen, are saved in a file under a specified name.
Note: This function is used to download the same settings to other printers.
-7-
B-EV4 Series Printer Setting Tool Operating Specification
e
Set
When the [Set] button is clicked, the parameter settings and fine adjustment value displayed on the
screen are downloaded to the printer.
f
Read
When the [Read] button is clicked, the parameter settings and fine adjustment value currently
programmed for the printer are read and displayed on the screen.
Note: This function cannot be used with the parallel interface.
g
Parameter
(1) Character code selection (FONT CODE)
• PC-850
• PC-852
• PC-857
• PC-8
• PC-851
• PC-855
• PC-1250
• PC-1251
• PC-1252
• PC-1253
• PC-1254
• PC-1257
• LATIN9
• Arabic
(2) Character zero selection (ZERO CODE)
• NO SLASH (0: without slash)
• WITH SLASH (Ø: with slash)
Note: The following fonts do not support a zero with slash (Ø). Even if a zero with a slash is selected, a zero
without slash is used.
[Bitmap font]
OCR-A, OCR-B, Japanese Kanji
[Outline font]
TrueTypeFont
(3) Baud rate selection (COMM. SPEED)
• 2400 bps
• 4800 bps
• 9600 bps
• 19200 bps
• 38400 bps
• 57600 bps
• 115200 bps
(4) Data bit length selection (DATA LENG.)
• 7 bits
• 8 bits
-8-
B-EV4 Series Printer Setting Tool Operating Specification
(5) Parity selection (PARITY)
• NONE
• EVEN
• ODD
(6) Stop bit length selection (STOP BIT)
• 1 bit
• 1.5 bits
• 2 bits
(7) Flow control code selection (CONTROL)
• XON/XOFF:
XON/XOFF mode
The printer does not output XON at the power on time or XOFF at the
power off time.
• READ/BUSY:
READY/BUSY (DTR) mode
The printer does not output XON at the power on time or XOFF at the
power off time.
• XON+READY AUTO: XON/XOFF+READY/BUSY (DTR) mode
The printer outputs XON at the power on time and XOFF at the power
off time.
• XON/XOFF AUTO:
XON/XOFF mode
The printer outputs XON at the power on time and XOFF at the power
off time.
• READY/BUSY RTS:
RTS mode
The printer does not output XON at the power on time or XOFF at the
power off time.
(8) Destination selection (DESTINATION) * Supported from V1.0D.
Note: No specific default setting is fixed for the destination selection. Choose one of the following
options correctly depending on your printer model.
If the QM is mistaken for JA or CSG, a character “\” will be replaced with “¥”, and if the JA or
CSG is mistaken for QM, a character “¥” will be replaced with “\”.
• QM (Global model)
• JA (Japanese model)
• CSG (Japanese custom model)
• JA-R (Simplified receipt mode for the Japanese model)
• QM-R (Simplified receipt mode for the global model)
(9) Auto forward wait selection (FORWARD WAIT)
• OFF: Auto forward wait function is inactivated.
• ON:
Auto forward wait function is activated.
(10) Control code selection (CODE)
• Automatic selection
• ESC LF NUL mode
• { | } mode
(11) FEED key function selection (FEED KEY)
• FEED: When the FEED key is pressed, one media is fed.
• PRINT: When the FEED key is pressed, one-label data in the image buffer is printed.
-9-
B-EV4 Series Printer Setting Tool Operating Specification
(12) Euro code selection (EURO CODE)
20H to FFH
(13) Automatic home position detection selection (AUTO HOME)
• OFF: Automatic home position detection is not performed.
• ON: Automatic home position detection is performed.
(14) Automatic sensor calibration selection (AUTO CALIB.)
• OFF: Automatic calibration is not performed.
• ON: Automatic calibration is performed.
(15) Model type selection (MODEL SELECT) * Supported from V1.0F.
Note: When the printer to be used is the B-EV4D, be sure to choose “DT”. If “TT” is selected, a
ribbon error occurs.
When the printer to be used is the B-EV4T, be sure to choose “TT”. If “DT” is selected,
ribbon error detection is not performed.
• DT (Direct thermal model)
• TT (Thermal transfer model)
(16) X Coordinate Fine Adjustment (X COORDINATE)
-995 to +995: -99.5 mm to +99.5 mm (in units of 0.5 mm Note)
XYZ
–
+
Note: The value can be set in units of 0.1 mm. However, the value which is actually set on the printer is in
units of 0.5 mm. When a value from 0.0 mm to 0.4 mm is set, it is actually set on the printer as 0.0 mm.
Also when a value from 0.5 mm to 0.9 mm is set, it is actually set on the printer as 0.5 mm.
(17) Receipt bottom margin setting (BLANK SPACE LEN.) * Supported from V1.0P.
Note: Be sure to read the parameter settings before setting the bottom margin of the receipt.
To enable this setting, choose “QM-R” for the DESTINATION parameter.
2 to 99: 2 mm to 99 mm
- 10 -
B-EV4 Series Printer Setting Tool Operating Specification
6. MAINTENANCE MODE PAGE
c
c SENSOR CALIB
This function makes the printer perform an automatic sensor calibration. Load the media which is
suitable for the selected sensor in advance.
(1) Sensor selection (SENSOR)
• REFLECT.: Reflective sensor
• TRANS.:
Transmissive sensor
• NONE:
No sensor
(2) SEND button
When the [SEND] button is clicked, a sensor calibration with the selected sensor is performed.
- 11 -
B-EV4 Series Printer Setting Tool Operating Specification
7. EXTRA SETTING PAGE
g
c
c
e
d
f
Load
When the [Load] button is clicked, the network settings are loaded from a specified setup file.
Note: This function is used to download the same settings to other printers.
d
Set
When the [Set] button is clicked, the network settings displayed on the screen are downloaded to the
printer.
e
Save
When the [Save] button is clicked, the configured network settings, displayed on the screen, are saved
in a file under a specified name.
Note: This function is used to download the same settings to other printers.
- 12 -
B-EV4 Series Printer Setting Tool Operating Specification
f
Read
When the [Read] button is clicked, the network settings currently programmed for the printer are read
and displayed on the screen.
g
LAN
(1) IP address setting (IP ADRESS)
000.000.000.000 to 255.255.255.255
(2) Subnet mask setting (SUBNET MASK)
000.000.000.000 to 255.255.255.255
(3) Default gate way setting (DEFAULT GATEWAY)
000.000.000.000 to 255.255.255.255
(4) Socket port setting (SOCKET PORT)
• OFF
• ON
(5) Socket port number setting
0 to 65535
(6) DHCP setting (DHCP)
• OFF
• ON
(7) DHCP host name setting (DHCP ID)
Up to 16 characters (ASCII)
- 13 -
B-EV4 Series Printer Setting Tool Operating Specification
8. FACTORY DEFAULT SETTING BY FIRMWARE VERSIONS
Parameter
Factory default
V1.0C
V1.0D/V1.0E
V1.0F
FONT CODD
PC-850
ZERO CODE
No slash
COMM. SPEED
9600 bps
DATA LENG.
8 bits
STOP BIT
1 bit
PARITY
None
CONTROL
DESTINATION
QM
ON
CODE
Automatic selection
FEED KEY
FEED
EURO CODE
B0H
----
AUTO CALIB.
----
MODEL SELECT
----
OFF
ON
-----
B-EV4D: DT B-EV4T: TT
X COORDINATE
0 mm
BLANK SPACE LEN.
----
SENSOR
2
Transmissive
IP ADDRESS
192.168.010.020
SUBNET MASK
255.255.255.000
DEFAULT GATEWAY
000.000.000.000
SOCKET PORT
ON
SOCKET PORT NO.
8000
DHCP
OFF
DHCP ID
V1.0P
XON/XOFF+READY/BUSY (DTR)
----
FORWARD WAIT
AUTO HOME
V1.0G
FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
- 14 -
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Page Count : 16 Page Mode : UseOutlines XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:704bff32-d6b8-42c6-9232-6aee7f2d34a5 Producer : Acrobat Distiller 6.0.1 (Windows) Modify Date : 2010:04:05 18:16:22+09:00 Create Date : 2009:08:20 11:09:36+09:00 Metadata Date : 2010:04:05 18:16:22+09:00 Document ID : uuid:22f0e174-80e5-4d4c-ba83-74a6f4b08a89 Format : application/pdf Title : untitledEXIF Metadata provided by EXIF.tools