BSWA308 309 User Manual 3v3
User Manual:
Open the PDF directly: View PDF
Page Count: 118 [warning: Documents this large are best viewed by clicking the View PDF Link!]
- Change History
- Contents
- Appearance
- Buttons of Operation
- 1. Introduction
- 2. The Appearance and Operation
- 3. Measurement Screen
- 4. Operation and Setting of the Menu
- 5. RS-232 Communication Protocol
- 5.1 Hardware Configuration and Settings of Interface
- 5.2 Transfer Protocol
- 5.3 Instruction
- 5.3.1 Instruction List
- 5.3.2 Instruction Format
- 5.3.3 Instruction Describe
- IDXp1: Setup ID
- IDX?: Query ID
- BRTp1: Set the RS-232 Baud Rate
- BRT?: Query The RS-232 Baud Rate Setting
- XONp1: Set the Flow Control
- XON?: Query Flow Control Setting
- RETp1: Set Response Mode
- RET?: Query Response Mode Setting
- MEMp1: Set the Measurement Mode
- MEM?: Query Measurement Mode Setting
- CALp1: Set Calibration Level and Calibrate by Measurement
- CAL?: Query Calibration Level and Calibration Factor
- CAFp1: Calibrate by Calibration Factor
- CAF?: Query Calibration History
- BSEp1_p2_p3_p4_p5_p6_p7: Measurement Setup
- BSE?: Query Measurement Setup
- RNS?: Query Measurement Range
- ICPp1: Set ICCP Power
- ICP?: Query ICCP Power State
- PR1p1_p2_p3_p4:Set Profile1
- PR1?: Query Profile1 Setting
- PR2p1_p2_p3_p4: Set Profile2
- PR2?: Query Profile2 Setting
- PR3p1_p2_p3_p4: Set Profile3
- PR3?: Query Profile3 Setting
- ALMp1: Set Alarm Threshold
- ALM?: Query the Alarm Threshold Setting
- ETFp1_p2_p3_p4_p5: Set Extended Function
- ETF?: Query Extended Function Setting
- STSp1_p2_p3……p11_p12: Set Statistical
- STS?: Query Statistical
- HISp1_p2: Set Time History
- HIS?: Query Time History Setting
- OCSp1_p2……p13_p14: Set Octave Setting
- OCS?: Query Octave Setting
- CUSp1_p2_p3_p4: Set Custom Measure
- CUSp1_?: Query Custom Measure Setting
- TISp1_p2_p3_p4_p5: Set Timer
- TIS?: Query Timer Setting
- CONp1: Set Contrast
- CON?: Query Contrast Setting
- BLTp1_p2: Set Backlight
- BLT?: Query Backlight Setting
- BAT?: Query Battery State
- TRGp1: Set Trigger
- TRG?: Query Trigger Setting
- DATp1_p2_p3_p4: Set Date
- DAT?:Query Date Setting
- HORp1_p2_p3: Set Time
- HOR?: Query Time Setting
- PWOp1: Set Auto Power Off
- PWO?: Query Auto Power Off Setting
- OPMp1: Set Boot Mode
- OPM?: Query Boot Mode Setting
- UMDp1: Set USB Mode
- UMD?: Query USB Mode Setting
- GPDp1_p2: Set GPS
- GPD?: Query GPS Setting
- VER?: Query About Information
- LNGp1: Set Language
- LNG?: Query Language Setting
- OUTp1_p2_p3_p4: Set Output
- OUT?: Query Output Setting
- RES: Apply Factory Settings
- STAp1: Start / Stop Measurement
- STA?: Query Measurement State
- DMAp1_?: Query the Main Screen Data
- TPRp1_?: Query 3-Profile Screen Data
- DLNp1_?: Query Statistical Analysis Data (LN)
- DCU?: Query Custom Measure Data
- DSLp1_p2_?: Query All the Data of the Sound Level Meter
- DOT?: Query 1/1 Octave Band Data
- DTT?: Query 1/3 Octave Band Data
- CSD: Save Custom Data into MicroSD
- 6. Operation Notes
- Annex 1 Glossary
- Annex 2 Adjustments at the Calibration Check Frequency
- Annex 3 Corrections for the Typical Effects of Reflections from the Case of Sound Level Meter and Diffraction of Sound around the Microphone
- Annex 4 Corrections of Windscreen in Free Field
- Annex 5 Corrections of Electrostatic Actuator
- Annex 6 Typical Frequency Response and Corresponding Upper Limit
- Annex 7 Specification of 1/1 Octave Band Filter
- Annex 8 Specification of 1/3 Octave Band Filter
- Annex 9 Mid-band Frequencies for 1/1 Octave Band and 1/3 Octave Band Filters