Brinly 3pt One Row Spring Shank Cultivator (CC 1000) Cultivator(CC

User Manual: Brinly 3pt One Row Spring Shank Cultivator (CC-1000) WFMFiles.com

Open the PDF directly: View PDF .
Page Count: 4

Download
Open PDF In Browser	View PDF

NG SHAN
LIMITED WARRANTY

Any parts found to be defective within the warranty period will be replaced, with proof of date of purchase, at
Brinly Hardy Company's expense. Our obligation under this warranty is expressly limited to replac.ement or
repair, at our option of parts which are defective in material or workmanship within thirty (30) days of
the parts. This warranty does not apply to damage caused by unreasonable use, including failure to
necessarymaintenance. nor does it.apply to an.y transportation or labor charges.
'Li'6...A'L... ILJII.

WE MAKE ,NO OTHER EXPRESS WARRANTY NOR IS ANYONE AUTHO'RIZED TO MAKE ANY
R
BEHALF. ANY IMPLII;D OR STATUTORY WARRANTIES, INCLUDING ANY WARRANTY 0
MERCHANTA'BILITY OR F'ITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE DURATION
THIS WRITTEN WARRANTY. WE SHALL NOT BE LIABLE FOR CONSEQUENTIAL OR INCI
DAMAGES OF·ANY KIND.
BR·INLY-HARDY COM·PANY (502) 5·~5-3351,

,--IN

. . . . .- - - -. . . . . .- - - -. . .- - - -. . . . 1I1111'1I .......

U.S.A.-----_--------...---

· ,ASSEMBLY:

IFIG. I
Assemble lower link pins (4) to "A" frame halves (5 & 6),
using 5/8 11 jam nuts (1'2), 5/8" lock washers (13)., and 5/8"
hex nuts (11).

Attach "A" frame halves together as shown, with spacing
plate (7). Secure with -1/2" x 1-3/4" hex bolts (9), lock
washers (14), and hex nuts (10) (in front holes only). FINGER
TIGHTEN.
.Assemble frame angles (1) to HA frame assembly as shown,
securing .with 1 (2" x 1-3/4" Hex Bolts (9) 1/2" plain washers
(15), 1/2" lock washers (14), and 1 /2" hex nuts (10). FINGER
TIGHTE-N.
U

FIG. I

Assemble the two frame struts. (2), to rear holes of "AU
,'frame, securing with 1/2" x 1-3/4" hex bolts (9), lock washers
(14), and hex nuts (10). FINGER TIG-HTEN.

FIG. II
Swing frame struts (2) into posltlcn shown, and assemble·
lawai ends to frame angies (i) using two 1/2" x 1-3/4" hex
bolts (9), 1/2" plain washers (IS):, 1/~, Jock washers (14),
and 1/2" hex nuts (10). (NOTE - Frame is shown' assembled
in the most common 90 0 position.) Frame :an9le ·m·ay be as...
sembled or adjusted to larger or smaller angie as 'desired by
position that frame struts (2) are attached to frame angl'es
(1). (See Fig. 11.)

Ass.amble spring shanks (8) to frame angles (1). Assemble
two shanks at position 1. and 2. using existing frame bolt,
nut and lock washer. DO NOT USE THICK WASHERS AT
POSITION 1 AND 2.

FIG. I~I
Assemble balance of ~pring shanks (8) as shown using.1 12"
x 1-3/411 hex bolts (9), 1/2" plain washers (15), 1/2" lock
washers (14), and 1/2" hex outs (10). Use 3/8" THICK washers (3) between frame angle (1) and spring shanks (8). Align

FIG. III

PREPARATION OF TRACTOR & HITCH:.

FIG. IV
Adjust rear wheels in or out to giv'e maximum plant foliage
clearance.
With hitch In lowered position, adjust lift rods until lower
link ball ends are approximately 8''' from ground.
........

FIG•

FIG. V
Attach stabilizer chains to lower link pins at tractor. DO NOT
TIGHTEN STABILIZER CHAIN.

Attach cultivator to lower links. Secure with spring pins.
Connect upper link to tractor in center hole, and to lower
hole in cultivator "A" frame. Secure with hitch pin and sprlnq
pin. Adjust upper link so cultivator rests level on the ground.
Tighten stabilizer chains to prevent side sway of cultivator
during operation.

LINK

.

.;

'STABiLIZER CHAINS/
CHAiN CONNECTiON
OPERATION:
Final cultivator adjustment and spring shank placement will
be determined by type and row spacing of crop being cultl-:
vated, Lengthening or shortening of upper link will cause
front or rear shovels to dig shallow or deeper.. When cultivating in light, loose soils, hydraulic lift lever may be set in
float position. However, if soil is heavy, crusted, or heavily
weeded, set hydraulic lift lever in a down-locked position.
Refer to Tractor Manual for operation of hydraulic lift and
controls. Additional weight may be added to cultivator frame
for better penetration when operating in hydraulic float
position.

FIG. V

NOTES:

CHAIN CONNECTION

· ;>'TO ORDER PARTS:

P.O.Box1116
Louisville, Ky. 40201
(502) 585-3351

Apply

the

logo

"

decal

9

10
14

Ref.
No.
1
2
3
4
5.

6
7

Part No.

Description

8...7.19.... 10

Frame Angle
Frame Strut
Washer, 1/2" 1.0.,3/8" Thick
(Special)
Pivot Link (Lower Link Pin)
"An Frame, L.H.
"An Frame, R.H.
Spacing Plate

8-720-10
8-723P
8-724P-0.l
8-1361 .... 10
8....1362.... 10
8-1363.... 10

l-1028 -1
"

Ref.
No.

Pert No.

Description

15

C-352-10
2M1628P
30M 1600P
3OM200OP
31M200OP
4OM200OP
40M160OP
45M1717P

16

8-46\85

Spring Shank
Hex Bolt, 1/2-13 x
Hex Nut j. 1/2"
Hex Nut, 5/8"
Hex Nut, (Jam) 5/8"
Lock Washer, .5/8"
Lock Wa sher , 1/2"
PI~ln Washer, 1/2"
Logo Decal

8
9

10
11

12
13
14



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Page Mode                       : UseOutlines
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Create Date                     : 2004:07:28 09:41:25Z
Modify Date                     : 2007:05:22 14:23:24-04:00
Metadata Date                   : 2007:05:22 14:23:24-04:00
Format                          : application/pdf
Creator                         : AUTHOR
Title                           : TITLE
Producer                        : Adobe Acrobat 8.0 Paper Capture Plug-in
Document ID                     : uuid:c333fd97-612c-4507-88a6-1db96fb65632
Instance ID                     : uuid:63549716-3f65-449d-a883-5c1d3206b60e
Page Count                      : 4
Author                          : AUTHOR

EXIF Metadata provided by EXIF.tools