Concord V4.0 Beta Installation Manual
Concord v4.0 Beta Installation Manual Concord v4.0 Beta Installation Manual
User Manual: Concord v4.0 Beta Installation Manual AlarmHow.net Library
Open the PDF directly: View PDF 
.
Page Count: 114
| Download | |
| Open PDF In Browser | View PDF |
) *(6HFXULW\ 466-2182 PRELIMINARY October 2004 ZZZJHVHFXULW\FRP Part Numbers: 600-1021-95R 600-1022-95R PRELIMINARY 10/18/04 Concord 4 Security Systems (Software Version 4.0) Installation Instructions Notices FCC Part 15 Information to the User Changes or modifications not expressly approved by GE Security can void the user’s authority to operate the equipment. FCC Part 15 Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the affected equipment and the panel receiver to separate outlets, on different branch circuits. • Consult the dealer or an experienced radio/TV technician for help. PRELIMINARY 10/18/04 ACTA Part 68 This equipment complies with Part 68 of the FCC Rules and the requirements adopted by the ACTA. Located on this equipment is a label that contains, among other information, the registration number and the ringer equivalence number (REN) for this equipment. If requested, this information must be provided to the telephone company. Registration No. US:AAAEQ##TXXXX The REN is used to determine the maximum number of devices that may be connected to your telephone line. Excessive RENs on a telephone line may result in devices not ringing in response to an incoming call. In most areas, the sum of all device RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label. A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements as adopted by ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compliant modular jack that is also compliant. See the Installation Instructions for details. Alarm dialing equipment must be able to seize the telephone line and place a call in an emergency situation. It must be able to do this even if other equipment (telephone, answering system, computer modem, etc.) already has the telephone line in use. To do so, alarm dialing equipment must be connected to a properly installed RJ31X jack that is electrically in series and ahead of all other equipment attached to the same telephone line. Proper installation is depicted in the following diagram. If you have any questions concerning these instructions, consult your local telephone company or a qualified installer about installing an RJ31X jack and alarm dialing equipment for you. C u s to m e r P r e m is e s E q u ip m e n t a n d W ir in g N e tw o rk S e r v ic e P r o v id e r 's F a c ilitie s A la r m D ia lin g E q u ip m e n t R J 3 1 X J a c k C o m p u te r U n u s e d R J -1 1 J a c k T e le p h o n e L in e N e tw o rk D e m a r c a tio n P o in t A n s w e r in g S y s te m T e le p h o n e T e le p h o n e F a x M a c h in e U n u s e d R J -1 1 J a c k T e le p h o n e If this equipment causes harm to the telephone network, the telephone company may temporarily disconnect your service. If possible, you will be notified in advance. When advance notice is not practical, you will be notified as soon as possible. You will also be advised of your right to file a complaint with the FCC. The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of the equipment. You will be given advance notice in order to maintain uninterrupted service. If you experience trouble with this equipment, please contact the company that installed the equipment for service and/or repair information. The telephone company may ask you to disconnect this equipment from the network until the problem has been corrected or you are sure that the equipment is not malfunctioning. This equipment may not be used on coin service provided by the telephone company. Connection to party lines is subject to state tariffs Patent Information This product and the use of this product may be covered by one or more of the following patents: 5,805,063, 5,872,512 5,942,981, 5,686,896, 5,686,885, 4,855,713. Except expressly provided herein, the purchase of this product shall not constitute a license or otherwise provide a right to practice a method covered by any of the identified patents. GE Security hereby grants the purchaser of this product a limited, non-exclusive license to practice the methods patented in the identified patents solely with products manufactured, sold or licensed by GE Security. This license grant does not extend to the use of unlicensed, third party products with this product. g GE Security 1275 Red Fox Road, Arden Hills, MN 55112 Technical Support: 800-777-2624 ©2003 GE Security. Concord is a trademark of GE Security. SuperBus is a registered trademark of GE Security. All other trademarks are properties of their owners. All rights reserved. Contents About This Manual 1 About the User’s Guide ...................................................................................................................... 1 Special Installation Requirements .............................................................................................................. 1 UL Listed Installations ........................................................................................................................... 1 Basic System ...................................................................................................................................... 1 Household Burglary Alarm System Unit (UL 1023) ......................................................................... 1 Household Fire Warning System (UL 985) ........................................................................................ 2 UL 1023 & 985 24-Hour Backup ....................................................................................................... 2 SIA System Requirements ...................................................................................................................... 2 SIA Setting Requirements .................................................................................................................. 2 Commercial Burglary Alarm System Unit (Grade C UL 1610) ......................................................... 3 UL 1610 24-Hour Backup .................................................................................................................. 3 UL 1635 Digital Alarm Communicator System ................................................................................. 3 Central Station Reporting ....................................................................................................................... 4 UL Canada Listed Installations .............................................................................................................. 4 Canadian Standards CSA Certified Accessories ................................................................................ 4 Residential Burglary Alarm System Unit (ULC-S309) ...................................................................... 4 Residential Fire Warning System Control Unit (ULC-S545-M89) .................................................... 4 California State Fire Marshall Listed Installations 4 Planning the Installation 4 Standard Panel ............................................................................................................................................ 4 SuperBus 2000 Touchpads ......................................................................................................................... 5 SuperBus 2000 RF Transceiver .................................................................................................................. 5 Power Line Carrier Transformer ................................................................................................................ 5 SuperBus 2000 Phone Interface/Voice Module .......................................................................................... 5 SnapCards ................................................................................................................................................... 5 SuperBus 2000 8Z Input Module (HIM) .................................................................................................... 5 SuperBus 2000 4-Relay Output Module (HOM) ....................................................................................... 5 Interrogator 200 Audio Verification Module .............................................................................................. 5 SuperBus 2000 Cellular Backup Module ................................................................................................... 5 SuperBus 2000 Energy Saver Module (ESM) ............................................................................................ 6 SuperBus 2000 Automation Module .......................................................................................................... 6 SuperBus 2000 Wireless Gateway-Ready Kit ............................................................................................ 6 SuperBus 2000 2 Amp Power Supply ........................................................................................................ 6 Dialog RF Electronic Thermostat ............................................................................................................... 6 Dialog RF Siren .......................................................................................................................................... 6 Dialog RF Iconized LCD Touchpad ........................................................................................................... 6 Installing the System 6 Determine the Panel Location .................................................................................................................... 7 Total System Power and Wire Length Guidelines ...................................................................................... 7 Power .................................................................................................................................................. 7 Wire Length ........................................................................................................................................ 7 Mounting the Panel ..................................................................................................................................... 9 Identify Panel Components 10 Installing Antenna Shrouds ...................................................................................................................... 10 Connecting the Panel to Earth Ground ..................................................................................................... 11 Installing Optional SnapCards .................................................................................................................. 11 Connecting Detection Devices to Panel Zone Inputs ............................................................................... 11 Connecting Intrusion Detection Devices .............................................................................................. 11 Connecting 2-Wire Smoke Detectors ................................................................................................... 12 Connecting 4-Wire Smoke Detectors .................................................................................................... 13 Connecting Speakers ................................................................................................................................ 13 15-Watt Speaker (13-060) .................................................................................................................... 13 Installation Instructions Contents y i Hardwire Interior Speaker (60-528) .....................................................................................................14 Connecting Exterior/Interior Piezo Sirens ................................................................................................14 Output 1 ................................................................................................................................................14 Piezo Dynamic Exterior Siren (13-950) ...........................................................................................14 Output 2 ................................................................................................................................................15 Hardwire Interior Siren (13-949) ......................................................................................................15 Connecting an Interrogator 200 Audio Verification Module (60-677) .....................................................15 Connecting SuperBus 2000 Touchpads ....................................................................................................16 Installing SuperBus 2000 Modules ...........................................................................................................16 Mounting Modules Inside the Panel Enclosure ....................................................................................16 SuperBus 2000 2 Amp Power Supply (600-1019) ...............................................................................17 SuperBus 2000 Transceiver Module (600-1025-95R) ..........................................................................17 SuperBus 2000 Phone Interface/Voice Module (60-777-01) ................................................................17 Power/Bus Wiring .............................................................................................................................17 Phone Line Wiring ............................................................................................................................18 Wiring for Status Voice Messages Only ...........................................................................................18 Wiring for Status and Alarm Messages ............................................................................................18 SuperBus 2000 Energy Saver Module (60-620-01) .............................................................................19 SuperBus 2000 8Z Input Module (60-774) ...........................................................................................19 SuperBus 2000 4-Relay Output Module (60-770) ................................................................................19 SuperBus 2000 Cellular Backup Module .................................................................................................20 SuperBus 2000 Automation Module (60-783-02) ....................................................................................20 SuperBus 2000 Wireless Gateway-Ready Kit (600-1010) ....................................................................... 21 Installing an RJ-31X Phone Jack (13-081) ...............................................................................................21 Connecting the Phone Line to the Panel with a DB-8 Cord .....................................................................21 Connecting the AC Power Transformer ................................................................................................... 22 Powering Up the Panel .............................................................................................................................23 Programming the Panel 23 Entering Program Mode ............................................................................................................................23 Touchpad Button Programming Functions ...............................................................................................24 Moving Through Program Mode Tiers and Menus ..................................................................................24 Programming Tier 1 Menu Items ..............................................................................................................25 Demo Kit Mode (System Programming)...........................................................................................25 Partition 1 Copy (System Programming) .........................................................................................25 Clear Memory (System Programming) ............................................................................................25 Programming Tier 2 Menu Items ..............................................................................................................26 Using Shortcut Numbers .......................................................................................................................26 Security Menu .......................................................................................................................................26 Partition Security ..................................................................................................................................27 Multi-Partition Arm/Disarm .................................................................................................................27 Keychain TP PTN .................................................................................................................................28 SIA False Alarm Reduction ..................................................................................................................28 Exit Extension .......................................................................................................................................29 Auto Stay Arming .................................................................................................................................30 Duress Code ..........................................................................................................................................31 Phones Menu .........................................................................................................................................31 Phone Options Menu ............................................................................................................................35 Dialer Abort ..........................................................................................................................................36 Dialer Abort Delay ................................................................................................................................37 Cancel Message ....................................................................................................................................37 Call Wait Cancel ...................................................................................................................................37 Timers Menu .........................................................................................................................................39 Entry Delay ...........................................................................................................................................41 Exit Delay .............................................................................................................................................41 Extended Delay .....................................................................................................................................41 Light Control Menu ..............................................................................................................................42 ii Installation Instructions Touchpad Options Menu ...................................................................................................................... 43 Reporting Menu .................................................................................................................................... 44 Swinger Limit ....................................................................................................................................... 47 Alarm Verify ......................................................................................................................................... 49 Siren Options Menu .............................................................................................................................. 50 Sensors Menu ....................................................................................................................................... 51 Audio Verification Menu ...................................................................................................................... 54 Accessory Modules Menu .................................................................................................................... 56 Onboard Options Menu ........................................................................................................................ 59 Smoke Verify ........................................................................................................................................ 59 Macro Keys Menu ................................................................................................................................ 61 Exiting Programming Mode ..................................................................................................................... 62 Entering Quick Programming Mode ........................................................................................................ 62 Entering User Programming Mode .......................................................................................................... 62 Time and Date Menu ............................................................................................................................ 63 User Codes Menu ................................................................................................................................. 63 Options Menu ....................................................................................................................................... 65 Set Up Schedules Menu ........................................................................................................................ 66 Attach Schedules to Events Menu ........................................................................................................ 67 Energy Saver Menu .......................................................................................................................... 69 Attach Lights to Sensors Menu ............................................................................................................ 69 System Version Menu ........................................................................................................................... 70 Downloader Programming ....................................................................................................................... 70 Enterprise Downloader Programming .................................................................................................. 70 Testing the System 70 Basic System Commands ......................................................................................................................... 71 Testing Zones/Sensors .............................................................................................................................. 71 If a Wireless Sensor Does Not Test ...................................................................................................... 72 Testing Phone Communication ................................................................................................................. 72 Testing Central Station/Pager Communication ........................................................................................ 72 Testing Outputs and Sirens ....................................................................................................................... 73 Testing Light Control ............................................................................................................................... 74 Testing the Energy Saver Module (ESM) ................................................................................................. 74 Changing Fixed Display LCD Touchpad Chime and Trouble Beep Tones .............................................. 74 Adjusting Touchpad Display Contrast ...................................................................................................... 74 Testing Audio Verification Module (AVM) Communication ................................................................... 74 Testing Cellular Backup Communication ................................................................................................ 75 Troubleshooting 76 Appendix A: System Planning Worksheets 82 Appendix B: Reference Tables 90 Cross-Zoning ............................................................................................................................................ 91 Notes for Table B8: Response Numbers .......................................................................................... 98 Appendix C: Settings 100 Appendix D: Software Release Notes 106 Specifications 106 System Wiring Notes 108 System Wiring Diagram Installation Instructions Back Page iii About This Manual This manual provides information for planning, installing, programming, and testing this security system. When necessary, this manual refers you to other documentation included with compatible peripherals. Planning sheets are included for you to record hardware layout and software programming settings. About the User’s Guide The User’s Guide (466-2183) contains user worksheets that should be filled out during the installation and programming of the system. For multi-partition systems, a User’s Manual for each partition is suggested. Special Installation Requirements This security system can be used as a fire warning system, an intrusion alarm system, an emergency notification system, or any combination of the three. Some installations may require configurations dictated by city/state codes, insurance, or Underwriter’s Laboratories (UL). This section describes the various component and configuration listings. UL Listed Installations This section describes the requirements for UL Listed installations. Basic System • • • • • Control Panel (600-1021-95R Concord 4 or 600-1022-95R Concord 4 Express) Standard Class II 16.5 VAC, 40 VA Power Transformer (600-1023) or Class II 16.5 VAC, 40 VA Line Carrier Power Transformer (600-1024) Backup Battery 12V 4 AH (60-681) or 12V 7 AH (60-680) SuperBus® 2000 Fixed Display Touchpad (60-820), 2x16 LCD Touchpad (60-746-01), ATP1000 (60-983) ATP2100 (60-985), ATP 2600 (60-984), 2x20 LCD Touchpad (60-803), or 2x20 VFD Touchpad (60-804) Interior Speaker Siren (60-528), Interior Siren (13-949), Exterior Speaker Siren (13-060), or Exterior Siren (13-950) per partition Basic system may also include a SuperBus 2000 RF Transceiver (600-1025-95R). Household Burglary Alarm System Unit (UL 1023) Basic system, plus: • • • • • • • • • • • • • • • 1 Hardwire Magnetic Contact (13-068 or 13-071) or Wireless Learn Mode Door/Window Sensor (60-362) Immediate Beeps set to on UL 98 Options set to on Receiver Failure set to on (if wireless devices are used) Siren Verify set to on Exit Delay set to 60 seconds Quick Exit set to off Siren Timeout set to 4 minutes or more Entry Delay set to 45 seconds or less RF TX Timeout set to 24 hours (if system includes a built in receiver or SuperBus 2000 RF Transceiver and wireless smoke sensors) Extended Delay set to off Sleep Time set to off Two Trip Error set to off Alarm Verify set to off Disable Trouble Beeps set to off Concord Household Fire Warning System (UL 985) Basic system, plus: • • • • • • • • • • • Hardwire Smoke Detector: System Sensor models 2100D, 2100TD, 2100S, 2100TS, 2400, or 2400TH learned into sensor group 26 or Sentrol (ESL) models 429AT, 521B or 521BXT learned into sensor group 26 Wireless Smoke Sensor 60-506-319.5 or 60-848-02-95 learned into sensor group 26 Immediate Beeps set to on UL 98 Options set to on Receiver Failure set to on (if wireless devices are used) Siren Verify set to on RF TX Timeout set to 4 hours (if system includes a built in receiver or SuperBus 2000 RF Transceiver and wireless smoke sensors) Sleep Time set to off Siren Timeout set to 4 minutes or more Two Trip Error set to off Disable Trouble Beeps set to off UL 1023 & 985 24-Hour Backup For 24-hour backup, the total current draw for all connected devices is limited to 90 mA (during normal standby conditions) using a 4.0 AH battery, or 190 mA (during normal standby conditions) using a 7.0 AH battery. SIA System Requirements Note UL requirements take priority over SIA requirements. SIA system requirements are the same as those described for a UL Listed Basic System on page 1, plus: • If multiple annunciation is required, use Hardwire Siren part no.13-949. SIA Setting Requirements The following table describes programming requirements to meet ANSI-SIA CP-01. Shortcut # Function Programming Page Reference Testing Page Reference Default Setting Required Setting 0004 SIA False Alarm Reduction 28 71 On On 0013 - 0063 Exit Extension 29 71 On On 0014 - 0064 Auto Stay Arming 30 71 On On 0017 - 0067 Duress Code 31 71 Disabled Disabled 02006 Dialer Abort 36 71 On On 02007 Dialer Abort Delay 37 71 30 Sec. 15-45 sec. 02008 Cancel Message 37 71 On On 02010 Call Wait Cancel 37 71 Disabled On if reporting to central station and customer has call waiting service 0310 - 0360 Entry Delay 41 71 30 sec. 30-240 sec. 0311 - 0361 Exit Delay 41 71 60 sec. 45-184 sec. 06015 Swinger Limit 47 71 1 1 1100 Smoke Verify 59 71 Off On if smoke alarms are programmed into system N/A Cross Zoning 91 71 Disabled Enabled for zones with a high probability of false alarms Concord 2 The following table describes non-programmable (hard coded) system operation as required to meet ANSI-SIA CP-01 and is provided only for your reference. Function Operation Disarm During Entry Delay Enter Code Only (or 1 + CODE) Cancel Alarm Enter Code Only (or 1 + CODE) Abort Annunciation Enabled Cancel Report Annunciation Enabled Commercial Burglary Alarm System Unit (Grade C UL 1610) Basic system using Control Panel 60-801-01 plus: • • • • • • • • • • • • • • • • • • • • • • • • • Hardwire Magnetic Contact (13-068 or 13-071) or Wireless Learn Mode Door/Window Sensor (60-499) SAW PIR Sensor (60-639-95R), Crystal PIR Sensor (60-703-95R), or DS924i PIR Sensor (60-511-01-95) Immediate Beeps set to on UL 98 Options set to on Receiver Failure set to on (if wireless devices are used) RF TX Timeout set to 4 hours 24-Hour Tamper set to on System Tamper set to on Auto Phone Test set to on Phone Test Freq. set to 1 Next Phone Test set to 1 Siren Verify set to on AC Failure set to on Exit Delay set to 120 seconds or less Quick Exit set to off Two Trip Error set to off Alarm Verify set to off Disable Trouble Beeps set to off Phone Number must be programmed High Level Rpts set to on Low Level Rpts set to on Comm. Failure set to on Extended Delay set to off Sleep Time set to off Siren Timeout set to 4 minutes or more UL 1610 24-Hour Backup • Same as UL 1023 & 985 UL 1635 Digital Alarm Communicator System Note For UL 1635 installations, Entry Delay plus Dialer Abort Delay must not exceed 60 seconds. 3 Same as UL 1023, 985 & 1610 plus: • • • • • • • • • AC Failure set to on Phone Number must be programmed Low CPU Battery set to on Next Phone Test set to 1 Phone Test Freq. set to 1 High Level Rpts set to on Low Level Rpts set to on Comm. Failure set to on RF Tx Timeout set to 4 hours Concord Central Station Reporting The panel has been tested with the following central station receivers using SIA and Contact ID reporting formats: • • • CS-5000 Central Station Receiver Sur-Gard Central Station Receiver with models SG-DRL2A and SG-CPM2 Osborne Hoffman UL Canada Listed Installations This section describes the requirements for CUL (UL Canada) Listed installations. Canadian Standards CSA Certified Accessories Residential Burglary Alarm System Unit (ULC-S309) Basic system as described for “UL 1023 Listed Installations” plus: • • Hardwire Magnetic Contact (13-068 or 13-071) or Wireless Learn Mode Door/Window Sensor (60-362) Siren Timeout set to 5 minutes or more Residential Fire Warning System Control Unit (ULC-S545-M89) Basic system as described for “UL 985 Listed Installations” plus: • Note For 24-hour backup, external power drain is limited to 90 mA (during normal standby condition) using a 4.0 AH battery, or 200 mA continuous using a 7.0 AH battery. Planning the Installation • • • Hardwire Smoke Detector: System Sensor models 2100D, 2100TD, 2100S, 2100TS, 2400, 2400TH learned into Sensor Group 26, or Sentrol (ESL) models 429AT, 521B, or 521BXT learned into sensor group 26 Wireless Smoke Sensor 60-506-319.5 or 60-848-02-95 learned into sensor group 26 Immediate Trouble Beeps set to on RF TX Timeout set to 4 hours (if system includes SuperBus 2000 RF Transceiver and wireless smoke sensors) California State Fire Marshall Listed Installations Same as Household Fire Warning System (UL 985), plus: • SMOKE VERIFY must be set to off This section describes system capabilities to help you get familiar with the system. “Appendix A” provides planning sheets with tables that let you record the hardware and programming configuration of the system. Fill in all necessary information ahead of time to help prepare for system installation. When planning the installation, keep in mind that the panel has the following capabilities (dependent upon devices used): • • Up to 16 SuperBus 2000 Devices (maximum of 4 RF transceivers in addition to onboard receiver) Up to 96 wireless or hardwired zones Standard Panel The following describe the basic panel (out-of-box) hardware capabilities. • • • • • • • Concord Power: Input for an AC step-down, plug-in style transformer. Auxiliary Power Output: Output that supplies 8.5 to 13.5 VDC with up to 1 amp for bus devices and hardwired detectors, such as smoke and motion detectors. Bus A and B: Input and output that provides communication between bus devices and the panel. Siren Driver: Output that can drive an 8-ohm load and provides intrusion and fire alarm sounds for partition 1. 2 Onboard Outputs: One 12 VDC source output and one open-collector output that can be set up to activate other signalling devices, based on system events. Microphone Input: Input used for 2-way audio when used in conjunction with the Interrogator 200 Audio Verification Module. 8 Supervised Hardwire Zones: Inputs for various hardwired detectors. Zone 8 can be set up in programming to accept 2-wire smoke detectors. 4 • • Built-In RF Receiver: Allows use of up to 96 or 32 319.5 MHz. crystal and/or SAW Learn Mode wireless sensors and touchpads. Phone Line Connection: Allows panel to communicate with central monitoring station and/ or pagers. SuperBus 2000 Touchpads The following touchpads can be used for installer/user programming and system operation. • • • • • • • SuperBus 2000 2x16 LCD Touchpad SuperBus 2000 2x20 LCD Touchpad SuperBus 2000 2x20 VFD Touchpad SuperBus 2000 ATP 1000 Touchpad SuperBus 2000 ATP 2100 Touchpad SuperBus 2000 ATP 2600 Touchpad SuperBus 2000 GTS 50 The following touchpads can be used only for installer quick programming, system operation and user programming. • SuperBus 2000 Fixed Display Touchpad SuperBus 2000 RF Transceiver The transceiver adds 2-way RF capability for use with compatible Dialog™ family devices and expands system wireless zones to the maximum allowed by the panel. The transceiver is compatible with all 319.5 MHz. crystal and SAW Learn Mode wireless sensors and touchpads. Power Line Carrier Transformer Using this transformer allows the use of X10 Powerhouse Lamp Modules for light control and light activation during alarms. SuperBus 2000 Phone Interface/Voice Module This module allows system access and control using touch-tone telephones, on- or off-site. The module includes an output for a speaker that sounds system status and alarm voice messages. SnapCards The following SnapCards expand the system as described: • • • 8Z Input SnapCard: Provides eight additional hardwire zone inputs, of which two are dedicated for using two wire smoke detectors. 4 Output SnapCard: Provides four form C relay outputs that can be set up to activate other signalling devices, based on system events, schedules, or direct control. 4Z Input/2 Output Combo SnapCard: Provides three hardwire zone inputs, one two wire smoke detector loop, and two outputs that can be set up to activate other signalling devices, based on system events, schedules, or direct control. SuperBus 2000 8Z Input Module (HIM) Provides eight additional hardwire zone inputs. SuperBus 2000 4-Relay Output Module (HOM) Provides four form C relay outputs that can be set up to activate other signalling devices, based on system events. Interrogator 200 Audio Verification Module Adding this module allows central station operators to listen-in and talk to occupants on the premises to verify the emergency when an alarm report is received. SuperBus 2000 Cellular Backup Module Provides central station communication (cellular transmission) as a backup to regular phone line(s). 5 Concord SuperBus 2000 Energy Saver Module (ESM) Provides a money-saving and convenient way to monitor and control temperatures. The ESM uses low- and high-temperature limits to save energy by overriding the existing HVAC thermostat. SuperBus 2000 Automation Module Provides a connection to a compatible home automation device. SuperBus 2000 Wireless Gateway-Ready Kit Allows users to control and monitor the status of their system from the alarm.com internet website. Adding a modem to the module provides the link to a wireless 2-way paging network for website access. SuperBus 2000 2 Amp Power Supply Provides an additional 12 VDC, 2 amps for powering system devices and is supervised via the panel data bus. Dialog RF Electronic Thermostat Wireless alternative to the SuperBus 2000 Energy Saver Module. Use one or the other (Partition 1 only). Dialog RF Siren Wireless siren that works via RF signals (Partition 1 only). Dialog RF Iconized LCD Touchpad Wireless touchpad with LCD screen that display system status, controls the system, and includes a built-in speaker for system messages (Partition 1 only). Installing the System This section describes how to install the system control panel. Before starting the installation, plan your system layout and programming using the worksheets provided in Appendix A. Installing the system consists of the following: • • • • • • • • • • • • • • • Concord Determining the Panel Location Determining Total System Power and Wire Length Guidelines Mounting the Panel Identifying Panel Main Components Installing Optional SnapCards Connecting Detection Devices to Panel Zone Inputs Connecting Speakers Connecting Piezo Sirens Connecting an Interrogator 200 Audio Verification Module Connecting Alphanumeric and Fixed Display Touchpads Installing SuperBus 2000 Modules Installing an RJ-31X Phone Jack Connecting the Phone Line to the Panel with a DB-8 Cord Connecting the AC Power Transformer Powering Up the Panel 6 Note (A) Class 2, Class 3, and power-limited fire alarm circuits must be installed using FPL, FPLR, FPLP, or substitute cable permitted by the National Electrical Code ANSI/NFPA 70. Wire that extends beyond the cable jacket must be separated from all other conductors by a minimum of 1/4-inch or by a nonconductive barrier. Determine the Panel Location Before permanently mounting the panel, determine panel location using the following guidelines: • • • • Centrally locate the panel with relation to detection devices whenever possible, to help reduce wire run lengths and labor. Locate the panel where the temperature will not exceed 120°F (49°C) or fall below 32°F (0°C). Avoid running wires parallel with electrical wiring or fixtures such as fluorescent lighting, to prevent wire runs from picking up electrical noise. Mount the panel at a comfortable working height (about 45 to 55 inches from the floor to the bottom of the panel, as shown in Figure 1). OR Phone Jack and Optional Module Mounting Area 1 9 .2 5 " (B) Class 2, Class 3, and power-limited fire alarm circuit conductors must be installed as Class 1 or higher circuits. 1 2 " Antenna Area 9 " 2 3 " P A N E L 4 5 -5 5 " 1 4 " Allow at least 24” in front of the panel to open cabinet door and access panel components. FLOOR Figure 1. Determining Panel Location • • • Leave space to the left and right of the panel for wiring, phone jack, and mounting optional modules. Allow at least 9 inches above the panel cabinet for antennas. Allow at least 24 inches in front of the panel to open the panel door. Total System Power and Wire Length Guidelines Power The panel can supply up to 1 amp (1,000 mA) for system devices connected to panel terminals 4 (+12V), 9 (OUT1), 11 (+12V), and 24 (2W SMK ZONE 8). Wire Length The total system wire length allowed can vary depending on devices powered by the panel, the wire length between devices and the panel, and the combined wire length of all devices. Table 1 describes the maximum wire length allowed between compatible devices and the panel, and the minimum and maximum current draw of each device. The minimum current draw of each device is based on the panel operating only from the backup battery. For 24-hour backup, the total current draw of all SnapCards connected to the panel and devices connected to +12V BUS (panel terminals 4 or 11) is limited to 90 mA (during normal standby condition) using a 4.0 AH battery, or 200 mA (during normal standby condition) using a 7.0 AH battery 7 Concord Table 1: Maximum Device Wire Length and MIn./Max. Current Draw Device Max. Wire Length Min. mA Max. mA to Panel Draw Draw SuperBus 2000 2x16 LCD Alphanumeric Touchpad 22 ga.—300 ft. 18 ga.—750 ft. 15 mA 90 mA SuperBus 2000 2x20 LCD Alphanumeric Touchpad 22 ga.—250 ft. 18 ga.—600 ft. 15 mA 120 mA SuperBus 2000 2x20 VFD Alphanumeric Touchpad 22 ga.—250 ft. 18 ga.—600 ft. 15 mA 120 mA SuperBus 2000 ATP 1000 Alphanumeric Touchpad 22 ga.—300 ft. 18 ga.—750 ft. 12 mA 110 mA SuperBus 2000 ATP 2100 Alphanumeric Touchpad 22 ga.—300 ft. 18 ga.—750 ft. 30 mA 165 mA SuperBus 2000 ATP 2600 Alphanumeric Touchpad 22 ga.—300 ft. 18 ga.—750 ft. 30 mA 165 mA SuperBus 2000 GUI Touchpad 22 ga.—100 ft. 18 ga.—250 ft. 270 mA 300 mA SuperBus 2000 Fixed Display Touchpad 22 ga.—300 ft. 18 ga.—700 ft. 11 mA 65 mA SuperBus 2000 RF Transceiver 22 ga.—1,000 ft. 18 ga.—2,500 ft. 45 mA 55 mA SuperBus 2000 Phone Interface/Voice Module 22 ga.—40 ft. 18 ga.—120 ft. 25 mA 600 mA no load no load SuperBus 2000 2 Amp Power Supply 4 Input/2 Output SnapCard N/A 20 mA 185 mA* 8Z Hardwire Zone Expander SnapCard N/A 38 mA 230 mA* 4 Output SnapCard N/A 1 mA 130 mA* SuperBus 2000 8Z Input Module 22 ga.—1,800 ft. 18 ga.—4,000 ft. 18 mA 35 mA SuperBus 2000 4-Relay Output Module 22 ga.—350 ft. 18 ga.—900 ft. 12 mA 180 mA SuperBus 2000 Energy Saver Module 22 ga.—1,600 ft. 18 ga.—4,000 ft. 20 mA 20 mA Standard Power: 22 ga.—15 ft. 18 ga.—40 ft. 90 mA 1600 mA High Power 22 ga.—10 ft. 18 ga.—30 ft. 90 mA 1900 mA SuperBus 2000 Automation Module 22 ga.—1,500 ft. 18 ga.—4,000 ft. 30 mA 35 mA SuperBus 2000 Wireless Gateway-Ready Kit 22 ga.—40 ft. 18 ga.—90 ft. 55 mA 1600 mA Interrogator 200 22 ga.—3,200 ft. 18 ga.—4,500 ft. 10 mA 10 mA Interrogator AVM 22 ga.—110 ft. 18 ga.—260 ft. 45 mA 300 mA SuperBus 2000 Cellular Backup Module *Maximum current draw for the SnapCards does not include the load which may be applied to their auxiliary DC supply. Concord 8 Table 2 describes the total system wire lengths allowed for all SuperBus 2000 devices when installing systems using unshielded or shielded cable. (The maximum wire length for individual devices is shown in Table 1) Table 2: Total System Wire Length Allowed Wire Type Total System Wire 18-gauge, unshielded 18-gauge, shielded 4,000 ft. 3,000 ft. 22-gauge, unshielded 22-gauge, shielded 4,000 ft. 3,000 ft. After determining panel location, run all necessary wires to that location using the guidelines in Table 3. Table 3: Wire Requirements Device Wire Requirements AC Power Transformer 2-conductor, 18-gauge, 25 feet max Earth Ground Single conductor, 16-gauge solid, 25 feet max Telephone (RJ-31X) 4-conductor Detection Devices 2- or 4-conductor, 22-gauge, 1,000 feet max 2- or 4-conductor, 18-gauge, 2,500 feet max (based on 30 ohms max loop resistance including device) Speakers 2-conductor, 18-gauge, 100 feet max SuperBus 2000 Devices 4-conductor, 22- or 18-gauge (see Table 1) Interrogator 200 AVM Power and Microphone 4-conductor, 22-gauge, shielded (see Table 1) 2-Wire Smoke Detectors 2-conductor, 22-gauge, 330 feet max 2-conductor, 18-gauge, 830 feet max (based on 10-ohms max loop resistance plus a 2k-ohm, end-of-line resistor) Mounting the Panel Use the following procedure to mount the panel to the wall or wall studs. ! Make sure you are free of static electricity whenever you work on the panel with the cover open. To discharge any static, first touch the metal panel chassis, then stay in contact with the chassis when touching the circuit board. Using an approved grounding strap is recommended. Caution ¾To mount the panel (see Figure 2): 1. Remove the panel door and remove the necessary wiring knockouts. Be careful not to damage the circuit board. 2. Feed all wires through wiring knockouts and place the panel in position against the wall. 3. Level the panel and mark the top and bottom mounting holes. 4. Install anchors where studs are not present. 5. Partially insert screws into the two top mounting hole locations, then hang the panel on the two screws. 9 Concord 6. Recheck for level, insert the two lower screws, and tighten all four mounting screws. _ + Mounting Holes Mounting Holes Figure 2. Mounting the Panel Identify Panel Components Before installing devices and making wiring connections, familiarize yourself with the main panel components. Figure 3 shows the main component locations. Antennas EEPROM B L K Microprocessor + SnapCard Header R E D Backup Battery Connections _ Programming Touchpad Header Terminal Strip Figure 3. Circuit Board Main Components Installing Antenna Shrouds Install a plastic antenna shroud (included with panel) over each antenna and snap them into the holes on top of the enclosure (see Figure 4). Figure 4. Installing Antenna Shrouds Concord 10 Note For best results, it is recommended that you crimp a spade lug on the wire end at the panel and secure the lug to the enclosure as shown in Figure 5. Connecting the Panel to Earth Ground For maximum protection from lightning strikes and transients, connect the enclosure to earth ground as shown in Figure 5. Use 16-gauge, solid copper wire from an earth grounded cold water pipe clamp to the enclosure. _ + To Water Pipe Pipe Ground Clamp Figure 5. Connecting the Panel to Earth Ground Installing Optional SnapCards The SnapCard Header on the right side of the panel allows for the installation of one SnapCard. Install the desired SnapCard onto the panel SnapCard Header and secure it in place with two screws, included with the card (see Figure 6). Connect all necessary input/output wiring using the Installation Instructions included with the card. Connector _ + SnapCard Header SnapCard Screw Locations Figure 6. Installing a SnapCard Note The panel comes with factory programmed onboard hardwire zones. Install 2k-ohm, end of line (EOL) resistors on all unused factory programmed onboard hardwire zones. If you don’t want to install EOL resistors, delete any unused zones from memory. See Table 7 for onboard hardwire zone factory programming. Connecting Detection Devices to Panel Zone Inputs Zone inputs 1 through 8 are supervised using included 2k-ohm, end-of-line resistors at the last device on each circuit. All eight zones accept either normally open (N/O) or normally closed (N/ C) detection devices. Connecting Intrusion Detection Devices Figure 7 shows the typical wiring for N/C and N/O door/window intrusion detection and the typical wiring for a Detection Systems model DS922 (part no. 13-082) motion detector. The minimum available panel voltage for hardwired PIR motion detectors is 8.5 VDC (9.5 VDC for UL listed installations). Note When using 2-wire smoke detectors on zone 8, the Two-Wire Smoke setting (in program mode) must be turned on before entering the LEARN SENSORS menu. See ONBOARD OPTIONS—INPUTS in the section “Programming the Panel” for complete details. 11 Concord Panel Terminals G N D Z O N E 1 Z O N E 2 G N D Z O N E 3 1 3 1 4 1 5 1 6 1 7 + 1 2 V G N D Z O N E 5 1 1 1 9 2 0 Motion Detector Normally Closed (N/C) Contacts In Series Normally Open (N/O) Contacts in Parallel 2k Ohm EOL Resistor 49-454 2k Ohm EOL Resistor 49-454 + L P L N 2k Ohm EOL Resistor 49-454 (Locate at Sensor) Figure 7. Connecting N/C and N/O Intrusion Detection and Motion Detector Circuits to the Panel Connecting 2-Wire Smoke Detectors Zone input 8 can be set up (in program mode) to accept the following 12 VDC, 2-wire smoke detectors: • • System Sensor models 2100D, 2100TD, 2100S, 2100TS, 2400, 2400TH ESL models 429AT, 521B, 521BXT—(models 521B and 521BXT require the following dip switch settings: 1-on, 2-off) ! Use only the 2-wire smoke detector models described above. Alarm signals from other detectors may not be processed correctly if the panel has lost AC power and is operating only from the backup battery. Caution When set up for 2-wire smoke detectors, zone 8 can handle up to 20 smoke detectors with 120 uA maximum idle current per detector. Maximum total loop current allowed in an alarm condition is 100 mA. Connect one or more, 2-wire smoke detectors to the panel as shown in Figure 9. Note The Two-Wire Smoke setting (in program mode) must be off when using 4-wire smoke detectors. See ONBOARD OPTIONS—INPUTS in the section “Programming the Panel” for complete details. 4-Wire 2-Wire G N D Z O N E 7 2 W S M K Z O N E 8 2 2 2 3 2 4 G N D Z O N E 7 2 W S M K Z O N E 8 2 2 2 3 2 4 C C O N O N . . . - .- M . M . O . O . + + + - Model 449AT - + C O O C N N . . .- .- M . M . O . O . + + 2k Ohm EOL Resistor 49-454 (Locate at Last Detector) 2k Ohm EOL Resistor 49-454 (Locate at Last Detector) Figure 8. Connecting 2 and 4-Wire Smoke Detectors to the Panel Concord 12 Connecting 4-Wire Smoke Detectors Note Zone 8 must be learned into sensor group 26 (fire) for connected smoke detectors to reset after canceling a fire alarm. Zone input 8 can be used with 4-wire smoke detectors that latch and remain in the alarm state until power is removed, then restored to the detector. The panel provides this power interruption from terminal 24 (2W SMK ZONE 8) only when zone 8 is learned into sensor group 26 (fire) and the Two-Wire Smoke option is on. Table 4 describes the minimum available panel power. Use only 4-wire smoke detectors that operate at these power limits. Connect up to five Sentrol (ESL) model 449AT (part no. 13-360) smoke detectors to panel power and zone 8 input as shown in Figure 8. Table 4: Panel Minimum Available Power Min. Voltage/Max. Current Available 8.3 VDC, up to 30 mA total (combined alarm) current 8.1 VDC, up to 40 mA total (combined alarm) current 7.6 VDC, up to 60 mA total (combined alarm) current 7.1 VDC, up to 80 mA total (combined alarm) current Connecting Speakers Note Install all sirens/speakers indoors, in a concealed location. The panel provides one siren driver output for intrusion (steady), fire (temporal 3), and auxiliary (on-off-on-off) alarm sounds. This output trips only for partition 1 alarms. The output can drive a single 8-ohm speaker or multiple speaker circuit of 8-ohms or higher (as shown in the following speaker wiring diagrams). Compatible speakers are described below. ! To avoid disabling the panel speaker output, do not make speaker connections with the panel powered up. Caution 15-Watt Speaker (13-060) For exterior siren applications, connect the speaker to the panel using 18-gauge wire as shown in Figure 9. Speaker 7 Speaker 8 7 8 Splice 2 8-Ohm Speakers in Series (16 Ohms) Figure 9. Connecting Exterior Speakers to the Panel 13 Concord Hardwire Interior Speaker (60-528) Connect interior speakers to the panel using 18-gauge wire as shown in Figure 10. Connect only the large speaker to the panel terminals 7 and 8 as shown. The smaller speaker cannot handle to output of terminals 7 and 8. To avoid damaging the speaker, the smaller speaker should not be connected to terminals 7 and 8. ! Caution Not Used Panel Terminals 7 8 Not Used Speaker Panel 7 Terminals 8 Not Used Speaker Figure 10. Connecting Hardwire Interior Speakers Connecting Exterior/Interior Piezo Sirens Output 1 Onboard output 1 (OUT 1—terminal 9) is a 12 VDC switched, programmable output that can handle a maximum of 1,000 mA current. The default setting (01614) activates the output 30 seconds after a police or fire alarm condition occurs. This allows you to connect a piezo siren without changing the output configuration number in programming. This output is typically used for exterior siren applications. (For more information on output configuration numbers, see “Onboard Options Menu”.) Piezo Dynamic Exterior Siren (13-950) Note This siren is not UL approved for use as an outdoor sounding device. Connect the siren to panel as shown in Figure 11. O U T 1 G N D 9 1 3 Red Panel Terminals Black Figure 11. Connecting Exterior Sirens Concord 14 Output 2 Onboard output 2 (OUT 2—terminal 10) is an open-collector (switched path-to-ground), programmable output that can handle a maximum of 300 mA current sink. The default setting (01710) activates the output for status and alarm tones, allowing for a piezo siren connection without changing the output configuration number. This output is typically used for interior siren applications. (For more information on output configuration numbers, see “Onboard Options Menu”.) Hardwire Interior Siren (13-949) This siren has two inputs; steady (#1) and warble (#2). Use the steady (#1) terminal for Concord 4 panels. The siren also includes a cover tamper switch that can be connected to a hardwire zone input on the panel, SnapCard or SuperBus 2000 Hardwire Input Module. Connect the siren to the panel/zone input terminals as shown in Figure 11. O U T 2 + 1 2 V 1 0 1 1 Panel Terminals To Zone Input 2k Ohm Resistor 49-454 S W S W G N D # 1 # 2 Figure 12. Connecting Exterior and Interior Sirens Connecting an Interrogator 200 Audio Verification Module (60-677) Connect the Interrogator 200 Audio Verification Module (AVM) to the panel terminals as shown in Figure 12. Partition 1 use only. ! Caution If a speaker is already connected to panel terminals 7 and 8, the Interrogator 200 speaker must be hooked up in series with that speaker to provide a 16-ohm load. Hooking up speakers in parallel to panel terminals 7 and 8 creates a 4-ohm load that can cause permanent damage to the panel. Splice Yellow Microphone Cable Panel Terminals Speaker Cable M IC G N D + 1 2 V 1 2 1 3 1 1 7 S P E A K E R 8 Cable Shield Figure 13. Connecting an Interrogator 200 AVM 15 Concord Connecting SuperBus 2000 Touchpads SuperBus 2000 touchpads may have wires or screw terminals. All use the same wiring scheme for power and bus connections. Connect touchpads to the as shown in Figure 13. B U S B 6 Panel Terminals G N D + 1 2 V 3 4 B U S A B 6 5 Touchpads with Terminals GND—Black 5 Bus B—White or Yellow 4 +12V—Red 3 A + 1 2 V Bus A—Green G N D + 1 2 V A B G N D / C O M Touchpads with Wires Figure 14. Connecting Touchpads to the Panel Installing SuperBus 2000 Modules SuperBus 2000 modules can be installed inside the panel cabinet or away from the panel with their included enclosure. Mounting Modules Inside the Panel Enclosure Use the following guidelines when mounting modules inside the panel enclosure (see Figure 14): • • • Note Even if you don’t plan to mount modules inside the cabinet, install the support standoffs for future use and to avoid losing them. • • Up to 4 of the SuperBus 2000 modules listed in Table 1 can be mounted inside the cabinet. The 2 Amp Power Supply and Phone Interface/Voice Module each use two mounting spaces when mounted inside the panel enclosure. The panel includes two support standoffs you install to secure module backplates to the panel. Install the standoffs at the locations shown. The cabinet has built-in mounting clips on the top and sides that module backplates slide onto for mounting. Top Mounting Clips (6) Side Mounting Clip Screws Support Standoffs Figure 15. Installing SuperBus 2000 Modules Concord 16 SuperBus 2000 2 Amp Power Supply (600-1019) Connect the power supply to the panel terminals and devices to be powered as shown in Figure 16. G N D + 1 2 V 3 4 B U S A B 6 5 C O N N E C T IO N Panel Terminals Power Supply Terminals N O Note Do not connect power (AC and battery) to the power supply until the panel is ready for power up. For power supply AC and battery connections, see the SuperBus 2000 2 Amp Power Supply Installation Instructions. 2 4 V A C 2 4 V A C B U S A + 1 2 V B U S B G N D + 1 2 V O U T G N D Z O N E G N D To power inputs on devices Figure 16. Wiring the SuperBus 2 Amp Power Supply to the Panel SuperBus 2000 Transceiver Module (600-1025-95R) The transceiver expands system capabilities as follows: • • • adds wireless capability to Hardwire Concord 4 panels. expands RF reception range when placed in the vicinity of sensors on the fringe of panel RF reception. adds Dialog 2-way RF device compatibility in systems with Hardwire Concord 4 or RF Concord 4 panels. Connect the transceiver (up to four) to the panel as shown in Figure 17. G N D + 1 2 V 3 4 Panel Terminals B U S A B 6 5 + 1 2 V A B Transceiver Terminals G N D Figure 17. Wiring the SuperBus 2000 RF Transceiver SuperBus 2000 Phone Interface/Voice Module (60-777-01) Note In UL Listed installations, the Phone Interface/Voice Module is for supplementary use only. The Phone Interface/Voice Module includes two backplates for mounting the module inside the control panel cabinet. The module can also be mounted outside of the control panel using an optional plastic housing (part no. 60-800). Refer to the SuperBus 2000 Phone Interface/Voice Module Installation Instructions included with each module, for complete mounting instructions. The module requires panel power and bus connections, phone line connection through panel terminals and DB-8 cord (from an RJ-31X jack), and speaker connection through panel terminals. Power/Bus Wiring Connect the module to the panel power and bus terminals as shown in Figure 18. Panel Terminals G N D + 1 2 V 3 4 A B U S B 6 5 Phone Interface/Voice Module Terminals 1 + 1 2 V A 2 B 3 4 G N D 5 G N D 6 7 S P K 1 S P K 2 8 9 1 0 A U D 1 A U D 2 G N D 1 1 T IP 1 1 2 T IP 2 1 3 R IN G 2 1 4 R IN G 1 Figure 18. Power and Bus Wiring for the Phone Interface/Voice Module 17 Concord Note For RJ-31X connections, see “Installing an RJ-31X Phone Jack (13-081). Phone Line Wiring For partition 1, connect the phone line to the module through the panel terminals and DB-8 cord (from an RJ-31X jack) as shown in Figure 19. For partitions 2-6 phone connections, see the SuperBus 2000 Phone Interface/Voice Module Installation Instructions. Phone Interface/Voice Module Terminals 2 B 3 4 G N D 5 G N D 9 8 1 0 A U D 1 A U D 2 G N D 6 7 S P K 1 S P K 2 1 2 T IP 2 1 3 R IN G 2 1 4 R IN G 1 G R N B R N G R Y R E D 2 5 2 6 2 7 2 8 Brown Green Panel Terminals 1 1 T IP 1 Red A Gray 1 + 1 2 V DB-8 Cord Brn Gry Grn Red RJ-31X Jack Figure 19. Phone Line Wiring for the Phone Interface/Voice Module Note To prevent status voice messages from being broadcast outside, do not connect exterior speakers to Phone Interface/Voice module terminals 6 and 7. Wiring for Status Voice Messages Only Connect an interior speaker to the Phone Interface/Voice Module terminals as shown under “Status” in Figure 20. When connected as shown, the speaker only produces status voice messages. In an alarm situation the speaker announces voice status messages. Wiring for Status and Alarm Messages Make the connection shown under “Status and Alarm” in Figure 20 only if the Phone Interface/ Voice Module is being installed in Partition 1 and alarm sounds are desired. In an alarm situation, the speaker alternates between alarm siren tones and voice status messages. Status Status and Alarm Phone Interface/Voice Module Terminals Phone Interface/Voice Module Terminals 1 + 1 2 V A 2 B 3 4 G N D 5 G N D 6 7 S P K 1 S P K 2 8 9 1 0 A U D 1 A U D 2 G N D 1 1 T IP 1 1 2 T IP 2 1 3 R IN G 2 1 4 R IN G 1 1 + 1 2 V A 2 B 3 4 G N D 5 G N D 6 7 S P K 1 S P K 2 8 9 1 0 A U D 1 A U D 2 G N D 1 1 T IP 1 1 2 T IP 2 1 3 R IN G 2 1 4 R IN G 1 S P E A K E R 7 Hardwire Interior Speaker (60-528) Not Used 8 Panel Terminals Not Used Figure 20. Wiring the Phone Interface/Voice Module for Status Only or Status and Alarm Messages Concord 18 SuperBus 2000 Energy Saver Module (60-620-01) Connect the Energy Saver Module to the panel and premises thermostat as shown in Figure 21. Energy Saver Module Thermostat H E A T 1 O F F 5 0 6 0 7 0 8 0 2 3 4 5 6 A /C 9 0 To HVAC G N D + 1 2 V 3 4 Panel Terminals A B U S B 6 5 Figure 21. Wiring the Energy Saver Module to the Panel SuperBus 2000 8Z Input Module (60-774) Connect the SuperBus 2000 8Z Input Module to the panel as shown in Figure 22. Connect all necessary input wiring using the Installation Instructions included with the module. SuperBus 2000 4-Relay Output Module (60-770) Connect the SuperBus 2000 4-Relay Output Module to the panel as shown in Figure 22. Connect all necessary output wiring using the Installation Instructions included with the module. Input Output ID : X X X X X X X X ID : X X X X X X X X 1 1 2 3 4 5 6 7 8 9 2 3 4 5 6 7 8 9 1 0 1 1 1 2 1 3 1 4 1 5 1 6 1 7 1 8 1 0 1 1 1 2 1 3 1 4 1 5 1 6 Z O N E C O M Z O N E 1 N O 4 C O M N C 4 N O 3 C O M N C 3 N O 2 C O M N C 2 N O 1 C O M 1 N C 4 3 2 1 Z O Z O Z O Z O Z O Z O Z O Z O Z O Z O Z O Z O N E N E N E N E N E N E N E N E N E N E N E N E 1 5 4 8 C O M M O N 7 6 C O M M O N C O M M O N 3 2 C O M M O N G N D + 1 2 V 3 4 A 5 B U S B G N D + 1 2 V 3 4 A 5 B U S B 6 6 Figure 22. Wiring Input and Output Modules to the Panel 19 Concord SuperBus 2000 Cellular Backup Module Connect the SuperBus 2000 Cellular Backup Module to the SuperBus 2000 2 Amp Power Supply and panel as shown in Figure 23. ! Since the SuperBus 2000 Cellular Backup Module draws more than 1 amp, it must be powered by the SuperBus 2000 2 Amp Power Supply and not the panel. Caution 1 2 3 4 5 6 Z C O M Z O N E 1 SuperBus 2000 2 Amp Power Supply Terminals 2 4 V A C 2 4 V A C B U S A + 1 2 V B U S B G N D + 1 2 V O U T G N D Z O N E G N D Figure 23. Wiring the Cellular Backup Module to the Panel SuperBus 2000 Automation Module (60-783-02) Connect the SuperBus 2000 Automation Module to the panel as shown in Figure 24. Automation Module Circuit Board DB-9 Serial Cable Automation Device 1 2 3 4 5 6 Z C O M Z O N E 1 Panel Terminals G N D + 1 2 V 3 4 A 5 B U S B 6 Figure 24. Connecting the SuperBus to the Panel Concord 20 SuperBus 2000 Wireless Gateway-Ready Kit (600-1010) Connect the SuperBus 2000 Wireless Gateway Module to the SuperBus 2000 terminals as shown in Figure 25. ! Since the SuperBus Wireless Gateway-Ready Kit draws more than 1 amp, it must be powered by the SuperBus 2000 2 Amp Power Supply and not the panel. Caution + 1 2 V A B G N D B U S A B U S B Z 1 Z C O M SuperBus 2000 2 Amp Power Supply Terminals 2 4 V A C 2 4 V A C + 1 2 V G N D + 1 2 V O U T G N D Z O N E G N D Figure 25. Connecting the Wireless Gateway Module to the Panel Note The panel cannot be used on a digital or PBX phone line. These systems are designed for digital type devices only, operating anywhere from 5 volts DC and up. The panel uses an analog modem and does not have a digital converter, adapter, or interface to operate through such systems. Installing an RJ-31X Phone Jack (13-081) Note Connecting the panel to an analog line off the phone switch places the panel ahead of the phone system, preventing panel access from phones on the premises. However, the panel can still be accessed from off-site phones. • Use the following guidelines when installing an RJ-31X phone jack for system control by phone and central station monitoring. • • • Locate the RJ-31X jack (CA-38A in Canada) no further than five feet from the panel. The panel must be connected to a standard analog (loop-start) phone line, that provides 48 volts DC (on-hook or idle). For full line seizure, install an RJ-31X phone jack on the premises phone line so the panel is ahead of all phones and other devices on the line. This allows the panel to take control of the phone line when an alarm occurs, even if the phone is in use or off-hook. If an analog line is not available, contact a telecommunications specialist and request an analog line off the phone switch (PBX mainframe) or a 1FB (standard business line). ¾To connect a phone line to the panel using an RJ-31X/CA-38A jack: 1. Run a 4-conductor cable from the TELCO protector block to the jack location (see A in Figure 26). 2. Connect one end of the cable to the jack (see B in Figure 26). 3. At the TELCO protector block, remove the premises phone lines from the block and splice them to the black and white (or yellow) wires of the 4-conductor cable (see C in Figure 26). 4. Connect the green and red wires from the 4-conductor cable to the TIP (+) and RING (-) posts on the block (see D in Figure 26). 5. Check the phones on the premises for dial tone and the ability to dial out and make phone calls. If phones do not work correctly, check all wiring and correct where necessary. Proceed to the “Troubleshooting” section of this manual if problems persist. Connecting the Phone Line to the Panel with a DB-8 Cord After installing the RJ-31X jack, you are ready to connect the phone line to the panel. A DB-8 cord (not included) uses a plug at one end for connecting to the RJ-31X module and flying leads on the other end for panel terminal connections. ¾To connect the DB-8 cord to the panel terminals and RJ-31X jack (see Figure 26): 1. Connect the green, brown, gray, and red flying leads from the DB-8 cord to panel terminals 24, 25, 26, and 27. 2. Insert the DB-8 cord’s plug into the RJ-31X. 3. Check the phones on the premises for dial tone and the ability to dial out and make phone calls. If phones do not work correctly, check all wiring and correct where necessary. Proceed to the “Troubleshooting” section of this manual if problems persist. 21 Concord Brn Gry T E L C O G R Y R E D 2 5 2 6 2 7 2 8 Red B R N Gray White (or Yellow) Red Red Black Green Grn G R N Brown B RJ-31X Jack Green H O U S E DB-8 Cord TELCO Protector Block A Dealer Cable Run TIP RING (+) (-) Brn Gry D Green Black Lines from Phones on Premises Green Red C RJ-31X Jack White (or Yellow) Grn Red Red Figure 26. Wiring an RJ-31X Jack and DB-8 Cord to the Panel Connecting the AC Power Transformer The panel must be powered by a plug-in stepdown transformer that supplies 16.5 VAC, 40 VA (600-1023). For systems that include X10 Lamp Modules, the panel must be powered with the Line Carrier Power Transformer that supplies 16.5 VAC, 40 VA (600-1024). Connect the power transformer to the panel as shown in Figure 27. ! Do not plug in the power transformer at this time. The panel must be powered up using the sequence of steps described in the next section, “Powering Up the Panel.” Caution Backup Battery Connections Panel Terminals 1 1 6 .5 V A C 2 _ Black + Red Battery Figure 27. Connecting Panel Power Transformer and Backup Battery Concord 22 Powering Up the Panel After connecting and wiring all devices to the panel, you are ready to apply AC and backup battery power to the panel. ¾To power up the panel (see Figure 27): 1. Connect the red and black battery leads (included with panel) to the lugs on the panel. 2. Connect the other ends of the battery leads to the battery terminals. 3. Plug the transformer into an outlet that is not controlled by a switch. Alphanumeric touchpads display ************, then SCANNING BUS DEVICES, and finally a date and time display. Note If alphanumeric touchpads don’t display anything, immediately unplug the transformer and disconnect the backup battery. Refer to the “Troubleshooting” section. 4. To permanently mount the transformer, unplug it and remove the existing screw securing the AC outlet cover. ! Use extreme caution when securing the transformer to a metal outlet cover. You could receive a serious shock if a metal outlet cover drops down onto the prongs of the plug while you are securing the transformer and cover to the outlet box. Warning Hold the outlet cover in place and plug the transformer into the lower receptacle. 5. Programming the Panel Note If the system is powered up after the programming touchpad is connected or if a bus command scan is executed, the programming touchpad will be “learned” into the system and must later be manually deleted. Use the screw supplied with the transformer to secure the transformer to the outlet cover. For on-site system programming, an alphanumeric touchpad is required. Entering Program Mode Entering program mode is done using an installer/dealer code (default = 4321). The system can be put into program mode only when all partitions are disarmed. ¾To enter program mode: 1. Make sure the system is disarmed in all partitions. 2. Press 8 + 4321 + 0 + 0. The display shows SYSTEM PROGRAMMING. ¾To enter programming mode using a programming touchpad: 1. Connect the red, black, green, and white wires from the Programming Touchpad Cable (60-791) to the power and bus wires/terminals on an alphanumeric touchpad, matching the +12V (red), Bus A (green), Bus B (white), and GND (black) on each. 2. Make sure the system is powered up and disarmed. 3. Connect the plug on the cable onto the panel programming touchpad header (see Figure 28). 4. Press 8 + 4321 + 0 + 2. The touchpad sounds one short beep. Press * and verify that the display shows SERVICE TOUCHPAD ACTIVE. 5. Press 8 + 4321 + 0 + 0 and the display shows SYSTEM PROGRAMMING. 6. After programming is completed, simply disconnect the touchpad from the panel header. T e s t S y s te m O ff W e e k ly A S ta y p re s s b o th N o D e la y 3 P a g e r 4 5 6 F e a tu re s S y s te m M e n u 7 8 9 S ta tu s L ig h ts B y p a s s 0 # C p re s s b o th D A w a y 2 S ile n t 1 p re s s b o th B * Programming Touchpad Cable (60-791) 6 0 7 3 4 G 3 0 8 D .D S F Figure 28. Connecting a Programming Touchpad 23 Concord Touchpad Button Programming Functions In program mode, touchpad buttons let you navigate to all installer programming menus for configuring the system. Table 5 describes the touchpad button functions in program mode. Table 5: Touchpad Button Functions Button Programming Function # Selects menu item or data entry. * Deselects menu item or data entry (if pressed before #). A (c) B (d) Scroll through available options at the current menu tier. Also scroll through sensor text options during sensor text programming. C Enters pauses when programming phone numbers. D Deletes certain programmed settings. 0 thru 9 Enter numeric values wherever needed. 1&2 Select off (1) or on (2) wherever needed. 1 thru 6 Press and hold to enter alphabetical characters A thru F for account numbers. 7&9 Press and hold to enter * (7) or # (9) for phone numbers. Moving Through Program Mode Tiers and Menus There are two basic tiers of programming menus (see Figure 29). Tier 1 Menus SYSTEM PROGRAMMING BdcA Tier 2 Menus #` · _ B` _A SECURITY #dc LIGHT CONTROL #dc B` _A · SENSORS #dc B` _A · · B` _A PHONES · B` _A #dc B` _A TOUCHPAD OPTIONS · AUDIO VERIFICATION · #dc · B` _A #dc B` _A #dc B` _A PHONE OPTIONS REPORTING · ACCESSORY MODULES · · B` _A #dc B` _A #dc B` _A TIMERS SIREN OPTIONS · B` _A #dc B` _A #dc ONBOARD OPTIONS · B` _A #dc MACRO KEYS Figure 29. Tier 1 and Tier 2 Program Menus Arrows pointing right or down represent pressing B or # to advance forward through the menus. Arrows pointing left or up represent pressing A or * to move through the menus in reverse. Only when SYSTEM PROGRAMMING is displayed can you advance to tier 2 menus. Only when a specific menu is displayed can you advance to those menu settings. For example, from the SENSORS menu pressing # gives you access to learning sensors, programming sensor text, deleting sensors, and viewing/editing sensor programming. Settings in tier 2 menus can also be accessed by entering shortcut numbers. See the section, “Programming Tier 2 Menu Items” for complete details. Concord 24 Programming Tier 1 Menu Items This section guides you through programming tier 1 menu items as they appear in sequence. The exact order you follow will depend on whether you’re installing a new system or changing programming in an existing system. Demo Kit Mode (System Programming) (Default = off) Determines whether the panel is used for a standard installation (off) or as a demo kit (on). When the Demo Kit option is on, only sensors learned into groups 01 and 03, duress code use, and phone test (8 + System Master Code + 2) will be reported. Turning on this feature and performing a memory clear changes the following settings: • • • • • • • • • • • • • • • • • • • • • • Partition 1 Master Code = 1000 Partition 2 Master Code = 2000 User Code 00 = 1001 (partition 1 code—can also be used to jump to partition 2) User Code 01 = 1002 (partition 1 code—can also be used to bypass sensors) User Code 02 = 2001 (partition 2 code—can also be used for remote or off-site access) User Code 03 = 2002 (partition 2 code—can also be used to perform system tests) User Code 04 = 1122 (partition 1 code—can also be used to jump to partition 2, for remote or off-site access, and system tests) User Code 05 = 2233 (partition 2 code—can also be used to jump to partition 1, for remote or off-site access, bypassing sensors, and system tests) Partition 1 House Code = 255 (P) Partition 2 House Code = 254 (O) Zone 1 (hardwire input 1) = Group 10, Front Door Zone 2 (hardwire input 2) = Group 13, Bedroom Window Zone 3 (hardwire input 3) = Group 17, Living Room Motion Sensor Zone 4 (hardwire input 4) = Group 1, Panic Zone 5 (wireless, keychain touchpad, ID F00201) = Group 01, (no text) Zone 6 (wireless, DWS, ID A00206) = Group 13, Kitchen Window COMM FAILURE = off Demo Kit = on AVM code = 1212 Entry Delay = 8 sec Exit Delay = 8 sec Extended Delay = 1 minute Siren Timeout = 2 minutes ¾To turn Demo Kit Mode off or on: 1. With the display showing DEMO KIT MODE OFF/ON (current setting), press 1 (off) or 2 (on), then press #. 2. The display flashes the entered setting, then stops after pressing # and displays DEMO KIT MODE OFF/ON (new setting). Partition 1 Copy (System Programming) (Default = none) After programming all settings pertaining to partition 1, you can make an exact copy to use for partitions 2-6. This helps reduce programming time when the system is set up for multiple partitions. If there are certain settings that are unique to partitions 2-6, simply advance to the appropriate menu and make the necessary changes. ¾To Copy Partition 1: With the display showing PARTITION 1 COPY, press # + installer CODE + #. The display flashes, then stops after pressing # and shows DONE. Clear Memory (System Programming) Note Clearing the memory will erase onboard hardwire zone factory programming. Clearing memory deletes all existing programming information (except the Dealer Code). ¾To Clear Panel Memory: 1. With the system in program mode, press A or B until the display shows CLEAR MEMORY. 2. Press # and the display shows ENTER CODE TO CLEAR MEMORY. 3. Enter the 4-digit installer or dealer code (if programmed) + #. After about five seconds, the system restarts and the panel scans the bus to learn all bus devices. If the system doesn’t respond as described, repeat step 3. 25 Concord Programming Tier 2 Menu Items This section guides you through programming tier 2 menu items as they appear in sequence. Figure 27 shows the menus available on tier 2. Each menu on tier 2 represents a group of settings related to the menu name. Some tier 2 menus break down into settings that affect the whole system (global) or a specific partition. Using Shortcut Numbers To go directly to a setting in tier 2, you can enter the shortcut number for that setting. Shortcut numbers in this manual appear in parenthesis ( ), next to the setting name. For example, this heading shows the Downloader Code global shortcut to be 0000. Downloader Code (0000) Security-Global (Default = 12345) Menus with partition settings have the series of shortcut numbers in parenthesis. For example, this heading shows the Account Number partition shortcut number series to be 0010 - 0060. Account Number (0010 - 0060) Security-Partition 1-6 (Default = 00000) The bold digit identifies the partition. To go directly to partition 3 account number, you would enter 0030. Shortcut numbers can be used from any setting location within tier 2. ¾To advance to tier 2 program menus: With the system in program mode and the display showing SYSTEM PROGRAMMING, press # once. The display should show SECURITY. Security Menu The SECURITY menu lets you choose whether security settings affect the whole system (global) or a specific partition. ¾To access global or partition security menu items: 1. With the display showing SECURITY, press #. The display should show GLOBAL. 2. Press # again to advance to global settings, or press A or B to display PARTITION n, then press # to advance to selected partition 1-6 settings. The following describes how to program the Security settings that appear under GLOBAL. Downloader Code (0000) Security-Global (Default = 12345) ¾ To program a Downloader Code: 1. With the display showing DOWNLOADER CODE nnnnn (current code), enter the desired 5-digit code, + ƒ. The display flashes the Note The Downloader Code cannot be deleted from panel memory. To change the entered code. Downloader Code to its default setting, enter 12345 in the procedure to the right. The Downloader Code will be reset to defaults during a Memory Clear only if the 2. Press ƒ and the display shows the new code. Dealer Code is not set OR if the Dealer Code is used to initiate the Memory Clear. The 5-digit downloader code is used in conjunction with downloader programming. The down-loader operator must have the panel account number and downloader code in order to perform any programming. Installer Code (0001) Security-Global (Default = 4321) The 4-digit installer code is used for entering program mode and changing ¾ To program a Installer Code: system settings. If a dealer code is programmed, only those settings not 1. With the display showing INSTALLER CODE associated with phone numbers and the Downloader Code can be changed. nnnn (current code), enter the desired 4-digit code. The display flashes the entered code. Note The Installer Code cannot be deleted or cleared from panel memory. To change 2. Press # and the display shows the new code. the Installer Code to its default setting, enter 4321. Concord 26 Dealer Code (0002) The 4-digit dealer code is used to prevent unauthorized persons from changing the programmed central station phone numbers and Downloader Code. When this feature is enabled, central station phone numbers and Downloader Code cannot be changed (unless you enter the program mode by using the dealer code). All other system settings are still accessible by entering the program mode with the installer code. Note The Dealer Code cannot be deleted by clearing panel memory. Security-Global (Default = none) ¾To program a Dealer Code: 1. With the display showing DEALER CODE ****, enter the desired 4-digit code. The display flashes the entered code. 2. Press # and the display shows the new code. ¾To delete a Dealer Code: 1. With the display showing DEALER CODE nnnn (current code), press D. The display shows DEALER CODE ****. Access Code Lock (0003) This setting determines whether or not the panel will include Access Codes when sending user information to the automation module. When this option is on, it means the Access Codes are not sent. Security-Global (Default = on) ¾To turn Access Code Lock off or on: 1. With the display showing ACCESS CODE LOCK ON/OFF, press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. Partition Security (0004) Controls whether an access code is required for partition jumping. When turned on, users can jump partitions without an access code by pressing 7 + 4 + PTN n (n = 1-6). When turned off, users must jump partitions with an access code by pressing 8 + CODE + 6 + PTN. Note Regardless of the setting, an access code can always be used to jump partitions. Multi-Partition Arm/Disarm (0005) Controls which partitions can be armed/disarmed simultaneously when using a touchpad and access code assigned to those partitions. When enabled, users can arm/disarm selected partitions using an authorized access code. When disabled, multiple partitions cannot be armed/disarmed simultaneously. • • • • • • • 27 At least two partitions must be selected for this feature to work. Touchpads must be assigned to at least one of the selected partitions of this menu for this feature to work. Access codes must be assigned to all selected partitions of this menu for this feature to work. If the partition assignment for a specific access code does not match the partitions selected in this menu, only those partitions common to both menu settings can be armed/disarmed simultaneously with that code. A partition cannot be armed/disarmed if it is being controlled by another source at that time. All arming modifiers (No Delay, Latchkey, Silent, etc.) affect all partitions being armed. When arming multiple partitions, any conditions that prevent arming (open sensor, trouble, active alarm, etc.) are identified on touchpad displays with the affected partition number flashing. The normal protest/auto force arm sequence follows, or pressing * cancels the arming request. When disarming multiple partitions, any partitions in alarm have the affected partition number flashing on touchpad displays. Pressing # cancels all alarms in the selected partitions. Alarm memory information is then displayed for all canceled alarms. Security-Global (Default = on) ¾ To turn Partition Security off or on: 1. With the display showing PTN SECURITY (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. Security-Global (Default = none) ¾ To enable Multi-Partition Arm/Disarm: 1. With the display showing MULTI-PTN ARM/DISARM _, press 1-6 to enter the desired partitions (at least two). The display flashes the entered partitions. 2. Press # and the display stops flashing. ¾ To disable Multi-Partition Arm/Disarm: 1. With the display showing MULTI-PTN ARM/DISARM n n n n n n n, select all of the displayed partitions by entering the appropriate partition number. The partition numbers disappear from the display. 2. Press #. Concord Keychain TP PTN (0006) Security-Global (Default = keychain TP partition assignment) Controls which partitions the selected keychain touchpad can arm/disarm. When enabled, the selected keychain touchpad can arm/disarm the partitions selected in this menu. When disabled, the selected keychain touchpad cannot arm/disarm multiple partitions. ¾ To enable Keychain TP PTN: 1. Learn all keychain touchpads into panel memory (see LEARN SENSORS menu). 2. Enter this menu (display showing KEYCHAIN TP PTN), then press #. The display shows the lowest touchpad sensor number assignment such as: S1 P1 G0 TP RF where S1 is sensor 1, P1 is partition 1, G0 is sensor group 0, TP is touchpad and RF is wireless. 3. Press # to accept this keychain touchpad or press A or B until the desired keychain touchpad appears, then press #. The display shows ARM PARTITION. 4. Enter the desired partitions 1-6 (at least two). The display flashes the entered partitions. 5. Press # and the display stops flashing. • • • • • • • If no keychain touchpads are learned into panel memory, this menu displays NOT AVAILABLE. When keychain touchpads are learned into panel memory, two submenus appear. The first one lets you view keychain touchpad assignments similar to that of viewing learned sensors (sensor #, partition learned into, sensor group, etc.). The second sub-menu lets you view and change the multi-partition arming assignments for that keychain touchpad. At least two partitions must be selected for this feature to work. Keychain touchpads can arm/disarm multiple partitions only for those partitions set up in the MULTI-PARTITION ARM/DISARM menu. A partition cannot be armed/disarmed if it is being controlled by another source at that time. When arming multiple partitions from a keychain touchpad (press and release Lock button), any conditions that prevent arming (open sensor, trouble, active alarm, etc.) are identified on touchpad displays in the partition where that condition exists. Touchpad displays in all other partitions being armed display PROTEST. The normal protest/auto force arm sequence follows, or pressing * on any touchpad in a partition being armed cancels the arming request. Pressing the Lock button again during a protest bypasses any open sensors in the affected partitions and arms those partitions. When disarming multiple partitions with a keychain touchpad and alarms are active in one or more of the assigned partitions: a). Protest beeps sound for five minutes in all partitions being disarmed; b). Partitions in alarm where sirens have timed out sound protest beeps for five minutes; c). Partitions in alarm with active sirens continue sounding the alarm. ¾ To disable Keychain TP PTN: 1. Follow steps 2 and 3 above. 2. Enter the partition numbers that are displayed (except for the partition you assigned the touchpad when it was learned). Each will disappear from the display with the touchpad’s original partition number left flashing. 3. Press # and the display stops flashing. In any case where alarms are active the premises may not be safe to enter. The user has these options: 1). Leave and call for help from a safe location; 2). If entering the premises anyway, go to a hardwired touchpad and check the system status to determine the alarm. Disarm and alarm memory is displayed for all assigned partitions; 3). Press the keychain touchpad Unlock button a second time (within the five minute protest period) to disarm all assigned partitions and cancel all alarms, then go to a hardwire touchpad and check alarm memory. SIA False Alarm Reduction (0007) Controls the following settings that are required by the SIA False Alarm Reduction Standard: Security-Global (Default = on) ¾ To turn SIA False Alarm Reduction off or on: 1. With the display showing SIA • Arming level changes made from wireless touchpads and keychain touchpads are FALSE ALARM (current setting), sounded (beeps) on exterior siren output (on) OR are not sounded on exterior siren outpress 1 (off) or 2 (on). The put (off). display flashes the entered setNote ting. The siren output must be configured for “Exterior Siren” (016xx) and on the two onboard outputs 2. Press ƒ and the display shows and SnapCard outputs only, for the arming level beeps to be annunciated. the new setting. • The Arming Always Silent feature is disabled for users if this setting is on OR can be controlled by users if the setting is off. Silent Arming on Demand is not affected. Concord 28 The following sections describe the Security settings that appear under PARTITION 1-6. Security-Partition 1-6 (Default = 00000) Account Number (0010 - 0060) The account number is used as panel (or customer) identification for the cen- ¾To program an Account Number: tral monitoring station. The panel sends the account number every time it 1. With the display showing ACCOUNT NUMreports to the central station. Account numbers must be 1 to 10 characters BER nnnnn (current number), enter the long. desired account number. The display flashes the entered number. Alpha characters A–F can be assigned to the account number by pressing 2. Press # and the display shows the new and holding buttons 1–6 respectively, until the character appears. number. Security-Partition 1-6 (Default = off) Quick Arm (0011 - 0061) Quick Arm allows system arming without using an access code. When Quick Arm is on, the system arming level can be increased from Level 1OFF to LEVEL 2-STAY, from Level 1-OFF to LEVEL 3-AWAY, or from Level 2-STAY to LEVEL 3-AWAY, without entering an access code. A valid access code is still required to decrease the arming level or disarm the system. ¾To turn Quick Arm off or on: 1. With the display showing QUICK ARM OFF/ ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. Quick Exit (0012 - 0062) Security-Partition 1-6 (Default = on) This setting determines whether or not users can open and close a standard entry/exit door without causing an alarm (while the system is armed). ¾To turn Quick Exit off or on: 1. With the display showing QUICK EXIT OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. This feature would be useful if the user wants to go out to get the morning paper while the system is armed. This feature also allows the user to leave the armed premises without having to disarm and re-arm the system. When Quick Exit is on, pressing D on a touchpad (while the system is armed) starts a 2-minute timer that allows one standard entry/exit door (sensor groups 10 and 19 only) to be activated once (opened, then closed). When this feature is turned off, the system must be disarmed before any protected door is opened. Note For UL Listed installations, this feature must be set to off. Exit Extension (0013 - 0063) Security-Partition 1-6 (Default = on) This setting determines whether or not the user can re-enter and exit again through an entry or exit delay door (without disarming and re-arming the system). This helps prevent exit faults and false alarms by allowing users to re-enter the premises for a forgotten item. ¾To turn Exit Extension off or on: 1. With the display showing EXIT EXTENSION OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. When Exit Extension is on, the panel restarts the exit delay timer if the user re-enters the premises through a standard delay door before the standard exit delay time expires. When this feature is off, the exit delay timer does not restart if the user re-enters the premises, forcing the user to disarm the system to avoid setting off an accidental alarm. 29 Concord Auto Stay Arming (0014 - 0064) Security-Partition 1-6 (Default = on) This setting determines whether or not the system automatically arms to STAY (level 2) if the user arms the system to AWAY (level 3) without exiting the premises. This can help prevent accidental alarms by deactivating interior motion sensors during occupied arming periods. Note Arming the system to “AWAY with No Delay” overrides the Auto Stay Arming feature. When this feature is on and the system is armed to AWAY, touchpads (and other status sounders) emit one exit delay beep every four seconds, then one every second during the last 10 seconds. If the exit delay time expires with no standard delay sensor activation (sensor groups 10 or 19), the system automatically arms to STAY. Keyswitch Sensor (0015 - 0065) Security-Partition 1-6 (Default = none) This feature lets users arm and disarm the system using either a keyswitch wired to a hardwire zone input or a wireless door/window sensor. Note It is recommended that keyswitch sensors are learned into group 28. For example, if sensor 1 is designated as the keyswitch sensor and the system is disarmed, then tripping sensor 1 could arm the system to AWAY. If the system is armed to STAY or AWAY, then tripping the sensor could disarm the system (depending on keyswitch style). The panel reports opening, closing, and force armed reports (if turned on) to the central monitoring station. Note A bypassed keyswitch sensor cannot arm or disarm the system.During an audible alarm, keyswitch sensors can disarm the system (which sends a cancel report to the central monitoring station), but cannot arm the system. The system can be armed only after the siren timeout expires.Keyswitch sensors test the same as any other sensor and do not arm or disarm the system during a sensor test. Keyswitch Style (0016 - 0066) ¾To turn Auto Stay Arming off or on: 1. With the display showing AUTO STAY ARMING OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. ¾To assign a Keyswitch Sensor: 1. With the display showing KEYSWITCH SENSOR nn (current sensor number), enter the desired sensor number (01– 96). The display flashes the entered sensor number. 2. Press # and the display shows the new number. ¾To delete a Keyswitch Sensor: 1. With the display showing KEYSWITCH SENSOR nn (current sensor number), press D to erase the keyswitch sensor attribute. Security-Partition 1-6 (Default = transition) ¾To assign a Keyswitch Style: 1. With the display showing KEYSWITCH STYLE TRANSITION/STATE (current setting), Transition: If keyswitch style is set to transition and the keyswitch sensor is press 1 for Transition or 2 for State. The tripped (opened) when the system is disarmed (level 1), the panel will autodisplay flashes the entered setting. matically arm to AWAY (level 3). If the sensor is tripped (opened) when the system is armed to AWAY (level 3) or STAY (level 2), the panel will automat- 2. Press # and the display shows the new setting. ically disarm. This feature allows users to select how they want the system to behave when armed/disarmed by a keyswitch sensor. The choices are as follows: State: If keyswitch style is set to state, when the keyswitch sensor is tripped (opened) the panel arms to AWAY (level 3). If the sensor is restored (closed) the panel disarms. Opening, closing, and force arming reports (if turned on) are reported to the central station for both keyswitch styles. Concord 30 Security-Partition 1-6 (Default = none) Duress Code (0017 - 0067) The duress code is a unique 4-digit access code that allows users to operate the system and, at the same time, instructs the panel to send a silent alarm report to the central station. Do not use a duress code unless it is absolutely necessary. Using duress codes often results in false alarms due to code entry errors. If a duress code is absolutely necessary, use it with an audio verification module (AVM) to reduce false alarms and accidental dispatches. Note To use this feature, the Duress Option setting under the reporting—partition 1 (2) menu must be turned on. ¾To program a Duress Code: 1. With the display showing DURESS CODE ****, enter the desired 4-digit duress code. The display flashes the entered setting. 2. Press # and the display shows the new code. ¾To delete a Duress Code: 1. With the display showing DURESS CODE nnnn (current code), press D. The display shows DURESS CODE ****. Phones Menu The PHONES menu lets you set up central station reporting for the system. The following describes how to program the settings that appear under CS PHONE 1-3. Phone Number (cs phone 1: 01000, cs phone 2: 01010, cs phone 3: 01020) Phones-CS 1-3 (Default = none) This setting is used for programming the central station receiver phone number. Phone numbers can be 1 to 24 digits long, including pauses or * and # characters. ¾To program a Central Station Phone To enter pauses, press C. To enter *, press and hold 7 for about two seconds. To enter #, press and hold 9 for about two seconds. 1. Note The PHONE NUMBER menus are not accessible if a Dealer Code is programmed and the Installer Code is used to enter installer programming mode. To access these menus when a Dealer Code is programmed, you must enter installer programming mode using the Dealer Code. 2. Call-waiting services should be disabled to prevent interrupting panel communication to the central monitoring station. To program a dialing prefix that disables call-waiting, see the Call Wait Cancel setting under the menu PHONE OPTIONS—GLOBAL. Number: With the display showing PHONE NUMBER _ (or current number), enter the desired phone number. The display flashes the entered number. Press # and the display shows the new number. ¾To delete a Central Station Phone Number: With the display showing PHONE NUMBER (current number), press D. The display shows PHONE NUMBER _. For UL 1610 & 1635 installations, a phone number must be programmed. High Level Rpts (cs phone 1: 01001, cs phone 2: 01011, cs phone 3: 01021) When this setting is on, the following conditions report to the central station: • • • • • • Fire, Police, Auxiliary, and Duress alarms No Activity Receiver Failure (or jam) Tamper conditions, including Zone Tampers and System Tamper (40 incorrect key presses or touchpad supervisory) Entering or exiting Sensor Test mode Phone Test Phones-CS 1-3 (Defaults:1 = on, 2&3 = off) ¾To turn High-Level Reports off or on: 1. With the display showing HIGH LEVEL RPTS OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. Note For UL 1610 & 1635 installations, this feature must be set to on. 31 Concord Low Level Rpts (cs phone 1: 01002, cs phone 2: 01012, cs phone 3: 01022) When this setting is on, the following non-alarm conditions report to the central station: • • • • • • Force Armed Hardwire Zone Trouble (open or short) Supervisory (wireless devices) Low Battery (wireless devices) Phone Test Other non-alarm related conditions Phones-CS 1-3 (Defaults:1 = on, 2&3 = off) ¾To turn Low-Level Reports off or on: 1. With the display showing LOW LEVEL RPTS OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. Note For UL 1610 & 1635 installations, this feature must be set to on. Exception Rpts (cs phone 1: 01003, cs phone 2: 01013, cs phone 3: 01023) Phones-CS 1-3 (Default = off) When this setting is on, the panel reports to the central station if the sys- ¾To turn Exception Reports off or on: tem is not armed or disarmed at the specified schedule times. 1. With the display showing EXCEPTION RPTS OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. Open/Close Rpts (cs phone 1: 01004, cs phone 2: 01014, cs phone 3: 01024) This setting determines whether opening and closing reports are sent to the central station. When turned on, the panel sends a closing report when the system is armed and an opening report when the system is disarmed. Note To use this feature, the Opening Reports and Closing Reports settings under the REPORTING menu must be turned on for that partition. Backup (cs phone 1: 01005, cs phone 2: 01015, cs phone 3: 01025) This setting determines whether or not the panel uses another programmed central station phone number for reporting if attempts with the first number are unsuccessful. When Back Up is off, the panel will make up to eight attempts to deliver a report with the programmed phone number. When Back Up is set to on, the panel makes up to 16 attempts to deliver the report, alternating between the programmed phone number and the backup phone number. Phones-CS 1-3 (Default = off) ¾To turn Opening/Closing Reports off or on: 1. With the display showing OPEN/CLOSE RPTS OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. Phones-CS 1-3 (Defaults:1 = on, 2&3 = off) ¾To turn Backup off or on: 1. With the display showing BACK UP OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. CS PHONE 1 is backed up by CS PHONE 2. CS PHONE 2 is backed up by CS PHONE 1. CS PHONE 3 is backed up by CS PHONE 1. Concord 32 SIA/CID Reporting (cs phone 1: 01006, cs phone 2: 01016, cs phone 3: 01026) This setting determines whether the panel uses the SIA or CID (Contact ID) reporting format for central station communication. Cellular Backup (cs phone 1: 01007, cs phone 2: 01017, cs phone 3: 01027) This setting determines whether the panel uses cellular communication for reporting if attempts using a landline are unsuccessful. Phones-CS 1-3 (Default = CID) ¾To select SIA or CID reporting: 1. With the display showing REPORTING FORMAT SIA/CID (current setting), press 1 (for SIA) or 2 (for CID). The display flashes the entered setting. 2. Press # and the display shows the new setting. Phones-CS 1-3 (Defaults:1 = on, 2&3 = off) ¾To turn Cellular Backup off or on: 1. With the display showing CELLULAR BACKUP, press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. The following describes how to program the Phones settings that appear under PAGER PHONE 1-5. Phone Number (pager 1: 01030, pager 2: 01040, pager 3: 01050, pager 4: 01060, pager 5: 01070) Phones-Pager Phone 1-5 (Default = none) ¾To program a Pager Phone Number: 1. With the display showing PHONE NUMBER _ (or current number), enter the desired pager phone number. The display flashes the entered Note Call-waiting services should be disabled to prevent interrupting panel communumber. nication to the pager(s). To program a dialing prefix that disables call-waiting, 2. Press # and the display shows the new setting. This setting is used for programming a phone number that communicates to a pager. Phone numbers can be 1 to 24 digits long and include pauses, a skylink number, and 7-digit PIN number. see the Call Wait Cancel setting under the menu PHONE OPTIONS—GLOBAL. To enter pauses, press C. To enter *, press and hold 7 for about two seconds. To enter #, press and hold 9 for about two seconds. High Level Rpts (pager 1: 01031, pager 2: 01041, pager 3: 01051, pager 4: 01061, pager 5: 01071) This setting determines whether the following alarm conditions report to a pager: • • • • • • 33 Fire, Police, Auxiliary, and Duress alarms No Activity Receiver Failure (or jam) Tamper conditions, including Zone Tampers and System Tamper (40 incorrect key presses or touchpad supervisory) Entering or exiting Sensor Test mode Phone Test ¾To delete a Pager Phone Number: 1. With the display showing PHONE NUMBER (current number), press D. The display shows PHONE NUMBER _. Phones-Pager Phone 1-5 (Default = on) ¾To turn High-Level Reports off or on: 1. With the display showing HIGH LEVEL RPTS OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. Concord Low Level Rpts (pager 1: 01032, pager 2: 01042, pager 3: 01052, pager 4: 01062, pager 5: 01072) Phones-Pager Phone 1-5 (Default = off) This setting determines whether the following non-alarm conditions report to a pager: • • • • • • Force Armed Hardwire Zone Trouble (open or short) Supervisory (wireless devices) Low Battery (wireless devices) Phone Test Other non-alarm related conditions Exception Rpts (pager 1: 01033, pager 2: 01043, pager 3: 01053, pager 4: 01063, pager 5: 01073) This setting determines whether the panel reports to a pager if the system is not armed or disarmed at the specified schedule times, if open/ close reports are turned on. Open/Close Rpts (pager 1: 01034, pager 2: 01044, pager 3: 01054, pager 4: 01064, pager 5: 01074) This setting determines whether opening and closing reports are sent to a pager. When turned on, the panel sends a closing report when the system is armed and an opening report when the system is disarmed. Note To use this feature, the opening reports and closing reports settings under the REPORTING menu must be turned on for that partition. Latchkey Reports (pager 1: 01035, pager 2: 01045, pager 3: 01055, pager 4: 01065, pager 5: 01075) This setting determines whether the panel reports to a pager when the system is armed or disarmed, according to latchkey time scheduling. ¾To turn Low-Level Reports off or on: 1. With the display showing LOW LEVEL RPTS OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. Phones-Pager Phone 1-5 (Default = off) ¾To turn Exception Reports off or on: 1. With the display showing EXCEPTION RPTS OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. Phones-Pager Phone 1-5 (Default = off) ¾To turn Opening/Closing Reports off or on: 1. With the display showing OPEN/CLOSE RPTS OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. Phones-Pager Phone 1-5 (Default = on) ¾To turn Latchkey reports off or on: 1. With the display showing LATCHKEY RPTS OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. Streamlining (pager 1: 01036, pager 2: 01046, pager 3: 01056, pager 4: 01066, pager 5: 01076) Phones-Pager Phone 1-5 (Default = on) This setting determines whether the panel includes (off) or excludes (on) the account number when reporting to a pager. ¾To turn Streamlining off or on: 1. With the display showing STREAMLINING OFF/ ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. Concord 34 Phones-Pager Phone 1-5 (Default = 1) Ptn Assignment (pager 1: 01037, pager 2: 01047, pager 3: 01057, pager 4: 01067, pager 5: 01077) ¾To set up Partition Assignments for pager This setting determines the partition that reports to a pager. All partitions can be assigned to report to a single pager. reporting: 1. 2. With the display showing PTN ASSIGNMENT 1/2/ 12 (current setting), press 1-6 to select the desired partitions. The display flashes the entered settings. Press # and the display stops flashing. The following describes how to program the settings that appear under DOWNLOADER PHONE. Phones-Downloader Phone (Default = none) Phone Number (01090) ¾To program a downloader phone number: 1. With the display showing PHONE NUMBER (current number), enter the desired phone number. The display flashes the entered number. Note Call-waiting services should be disabled to prevent interrupting panel commu- 2. Press # and the display shows the new setting. Use this setting to enter the phone number of an off-site computer that can be used to program the panel through the phone line. Phone numbers can be 1 to 24 digits long, including pauses or * and # characters. nication to the downloader. To program a dialing prefix that disables call-waiting, see the Call Wait Cancel setting under the menu PHONE OPTIONS— GLOBAL. To enter pauses, press C. To enter *, press and hold 7 for about two seconds. To enter #, press and hold 9 for about two seconds. ¾To delete a downloader phone number: 1. With the display showing PHONE NUMBER (current number), press D to erase the number. The display shows PHONE NUMBER_. Phone Options Menu The PHONE OPTIONS menu lets you set up system phone access and communications that affect the whole system (global) or a specific partition. The following describe how to program the Phone Options settings that appear under GLOBAL. Phone Test (02000) Phone Options-Global (Default = on) This setting determines if the user can, at any time, test the communica- ¾To turn the Phone Test setting off or on: tion from the panel to the central station or a pager by entering 8 + 1. With the display showing PHONE TEST OFF/ON CODE + 2 (# + 8 + CODE + 2 from a touch-tone phone). (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. Note 2. Press # and the display shows the new setting. For UL 1610 & 1635 listed installations, this feature must be set to on. Auto Phone Test (02001) This setting determines if the panel sends a phone test automatically to the central station or a pager on a predetermined schedule. (Refer to the “Phone Test Freq.” and “Next Phone Test” settings found under TIMERS— GLOBAL). Note For UL 1610 & 1635 listed installations, this feature must be set to on. 35 Phone Options-Global (Default = off) ¾To turn Automatic Phone Test off or on: 1. With the display showing AUTO PHONE TEST OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. Concord Auto Test Reset (02002) Phone Options-Global (Default = on) ¾To turn Auto Test Reset off or on: 1. With the display showing AUTO TEST RESET OFF/ON (current setting), press 1 (off) or 2 (on). The disWhen this feature is on, the panel considers any successful report to the central monplay flashes the entered setting. itoring station to be a successful phone test. Thus, any panel report resets the Next 2. Press # and the display shows the Phone Test setting to the Phone Test Freq. value. The panel only conducts an Auto new setting. Phone Test if no other reports have been made during the Phone Test Freq. time period. This setting determines whether or not the Auto Phone Test interval is reset after any successful report to the central monitoring station. (Refer to the “Phone Test Freq.” and “Next Phone Test” settings found under TIMERS—GLOBAL). Note Phone Test Freq must be set to 2 or higher for Auto Test Reset to work. When this feature is off, an Auto Phone Test is always conducted according to the schedule of the Phone Test Freq. setting, even if the panel makes other reports to the central monitoring station during that time period. Phone Options-Global (Default = on) Comm Failure (02003) This setting determines whether the panel activates trouble beeps to alert users on the premises that communication to the central station failed. Failure notification occurs after the third unsuccessful reporting attempt to the central station/pager. ¾To turn Communication Failure notification off or on: 1. Failure notification can occur immediately if inadequate phone line voltage is detected upon the initial dialing attempt. Note For UL Listed installations, Comm Failure must be turned on. DTMF Dialing (02004) This setting determines whether the panel uses DTMF tones (on) or pulse (off) for dialing programmed phone numbers. Dialer Abort (02006) This setting determines whether or not the user can stop a panel before it sends a false alarm to the central station. Note Fire alarm reports to the central station cannot be aborted. When this feature is on, alarm reports from sensors in groups 00–20, 34, and 35 can be aborted. To abort the dialing attempt, the user must enter 1 + user code within the Dialer Abort Delay time setting (defaulted to 30 sec). Cancel and restoral reports from these sensor groups are aborted at the same time. The following reports can also be aborted. • • • • 2. With the display showing COMM FAILURE OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. Press # and the display shows the new setting. Phone Options-Global (Default = on) ¾To turn DTMF Dialing off or on: 1. With the display showing DTMF DIALING OFF/ ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. Phone Options-Global (Default = on) ¾To turn Dialer Abort off or on: 1. With the display showing DIALER ABORT OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. System Alarm Tamper/Cancel No Activity Alarm/Cancel Touchpad Police and Auxiliary Panic/Cancel Recent Closing and Two Trip Error Concord 36 Dialer Abort Delay (02007) This setting determines how much time the user has to abort a panel report. Note For UL Listed systems, the combined time for the Entry Delay and Dialer Abort Delay must not exceed 60 seconds. Cancel Message (02008) This setting determines whether or not the panel displays a cancel message after the user disarms the system to clear an alarm condition. Pager Delay (02009) This setting determines how long a report is delayed to a pager, after the panel dials the pager number. Note The Pager Delay time should not be set below 5 seconds, unless absolutely necessary. Call Wait Cancel (02010) This feature lets you set up a dialing prefix to disable the call waiting feature before the panel makes its first dialing attempt to any programmed central monitoring station or downloader phone number. The prefix can be up to eight digits. To enter pauses, press C. To enter *, press and hold 7 for one second. To enter #, press and hold 9 for one second. ! Phone Options-Global (Default = 30 sec.) ¾To change the Dial Abort Delay: 1. With the display showing DIAL ABORT DELAY nn SECS (current setting), enter the desired time (15–45). The display flashes the entered setting. 2. Press # and the display shows the new setting. Phone Options-Global (Default = on) ¾To turn Cancel Message off or on: 1. With the display showing CANCEL MESSAGE OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. Phone Options-Global (Default = 15 sec.) ¾To set the Pager Delay time: 1. With the display showing PAGER DELAY nn SECS (current setting), enter a delay time (0–30). The display flashes the entered setting. 2. Press # and the display shows the new setting. Phone Options-Global (Default = none) ¾To set up Call Wait Cancel: 1. With the display showing CALL WAIT CANCEL __ (or current setting), enter the desired prefix. The display flashes the entered setting. 2. Press # and the display shows the new setting. ¾To delete the Call Wait Cancel prefix: 1. With the display showing CALL WAIT CANCEL __ (or current setting), press D. DO NOT change this option from its default until verifying with the customer that they have call waiting with their phone service provider. Changing this option from its default without call waiting will prohibit the panel from calling the central station. Caution Dial Tone Detect (02011) When this setting is on, the panel begins dialing as soon as it detects a dial tone. When this feature is off, the panel begins dialing a few seconds after seizing the phone line. Note There is no Dial Tone Detect on the last dialing attempt. 37 Phone Options-Global (Default = on) ¾To set up Dial Tone Detect: 1. With the display showing DIAL TONE DETECT OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. Concord The following sections describe the Phone Options settings that appear under PARTITION 1-6. A Phone Interface/Voice Module must be installed for the system to use the settings under PHONE OPTIONS— PARTITION 1-6 (except Line Fail Delay). Phone Options-Partition 1-6(Default = on) Local Phone Control (0210 - 0260) When this feature is on, the panel can be accessed from a phone on the premises. ¾To set up Local Phone Control: 1. With the display showing LOCAL PHONE CTRL OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. Phone Options-Partition 1-6 (Default = on) Remote Access (0211 - 0261) When this setting is on, the panel can be accessed from an off-site phone. ¾To turn Remote Access off or on: 1. With the display showing REMOTE ACCESS OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. Ring/Hang/Ring (0212 - 0262) Phone Options-Partition 1-6 (Default = on) This setting determines how the panel picks up (seizes) the phone line. Select “on” if an answering machine shares the phone line with the panel. Select “off” if there is no answering machine sharing the phone line with the panel. ¾To turn Ring/Hang/Ring access off or on: 1. With the display showing RING/HANG/ RING OFF/ON (current setting), press 1 (off) or 2 (on). The display begins flashing the entered selection. 2. Press # and the display shows the new setting. Note The Remote Access setting must be turned on for this feature to work. When this feature is on, the person who is calling the panel must use the following procedure: 1. 2. 3. Listen for one or two full rings. Hang up. Call the premises again within the next 10–40 seconds. The system answers after the first ring. When this feature is off, the system answers after 12 full rings. Line Fail Delay (partition 1: 0213) This setting determines the amount of time the partition 1 phone line voltage must be absent before the panel indicates a phone failure trouble condition. If a delay is not programmed (default), the panel will not monitor the phone line voltage. Note Line Fail Delay is not available for partitions 2-6 at this time. Concord Phone Options-Partition 1 only (Default = none) ¾To set the Line Fail Delay time: 1. With partition 1 selected, press A or B until the display shows LINE FAIL DELAY nn SECS (current setting). 2. Enter the desired time value (10–240 seconds). The display flashes the entered setting. Press # and the display shows the new setting. ¾To delete the Line Fail Delay time: 1. With partition 1 selected, press A or B until the display shows LINE FAIL DELAY nn SECS (current setting). 2. Press D to delete the current line fail delay time. 38 Toll Saver (0214 - 0264) Phone Options-Partition 1-6 (Default = on) This setting determines whether the panel answers a phone call on the eighth ring (on) or twelfth ring (off) when a trouble or alarm condition exists. ¾To turn Toll Saver off or on: 1. With the desired partition selected, press A or B until the display shows TOLL SAVER OFF/ON (current setting). 2. Press 1 (off) or 2 (on). The display flashes the entered setting. Press # and the display shows the new setting. Phone Options-Partition 1-6 (Default = off) Phone Panic (0215 - 0265) This setting determines whether or not a police panic alarm can be activated from a touch-tone phone. When this feature is on, pressing # + ****** from a touch-tone phone on the premises causes a panic alarm. ¾To turn Phone Panic off or on: 1. With the desired partition selected, press A or B until the display shows PHONE PANIC OFF/ON (current setting). 2. Press 1 (off) or 2 (on). The display flashes the entered setting. Press # and the display shows the new setting. Phone Access Key (0216 - 0266) Phone Options-Partition 1-6 (Default = #) This setting determines which touch-tone phone button is used for system access and control. ¾To change the Phone Access Key: 1. With the desired partition selected, press A or B until the display shows PHONE ACCESS KEY #/* (current setting). 2. Press 1 (for *) or 2 (for #). The display flashes the entered setting. Press # and the display shows the new setting. If the Local Phone Control feature is enabled, the user can pick up the phone and press # (within 5 seconds) to access the security system. The panel seizes the phone line and waits for the user to enter system commands. Phone access can be changed from # to * (see the following note). Note Use the default setting (#) to avoid conflicts between the security system and other phone devices and services. Many phone devices (such as answering machines, computer modems, and FAX machines) and services (such as call-waiting, call-forwarding, and some banking transactions) require * to initiate their operation, so using * for this security feature could cause conflicts. Timers Menu The TIMERS menu lets you set up the various system feature times that affect the whole system (global) or a specific partition. The following describes how to program the Timers settings that appear under GLOBAL. Supervisory Time (0300) This setting determines what time of day the panel sends supervisory, low battery, or auto phone test reports to the central station. Note The panel clock must be set with the correct time for accurate supervisory time reporting. See “Time and Date Menu”. 39 Timers-Global (Default = set randomly between 01:00 and 04:00) ¾To set the Supervisory Time: 1. With the display showing SUPERVISORY TIME HH:MM (current setting), enter the desired 4digit time value. For example, enter 0330 to set the supervisory time for 3:30 A.M. The display flashes the entered setting. 2. Press # and the display shows the new setting. Concord RF Tx Timeout (0302) Timers-Global (Default = 12 hours) This setting determines how many hours (2–24) the panel has to receive at least one signal from a wireless sensor (learned into a supervised group). If the panel does not receive a signal from any supervised wireless sensor within the set time, the panel reports a supervisory condition to the central station. Note For UL 985, 1610 & 1635 listed installations, the RF Tx Timeout must be set to 4 hours. For UL 1023 listed installations, the RF Tx Timeout must be set to 24 hours. Timers-Global (Default = 7 days) Phone Test Freq. (0303) This setting determines how often the panel conducts the automatic phone test (see “Auto Phone Test” under PHONE OPTIONS—GLOBAL). The system can be set to perform an automatic phone test anywhere from every day to every 255 days. Note For UL 1610 & 1635 listed installations, this feature must be set to 1. ¾To set the Phone Test Freq: 1. With the display showing PHONE TEST FREQ nnn DAYS (current setting), enter the number of days (1–255). The display flashes the entered setting. 2. Press # and the display shows the new setting. Timers-Global (Default = 7 days) Next Phone Test (0304) This setting is used by the Auto Phone Test feature (see PHONE OPTIONS— GLOBAL) to determine when the next automatic phone test should occur. This setting should be the same as, or less than, the Phone Test Freq. setting. Note For UL 1610 & 1635 listed installations, this feature must be set to 1. ¾To set the Next Phone Test: 1. With the display showing NEXT PHONE TEST nnn DAYS (current setting), enter the number of days (1–255). The display flashes the entered setting. 2. Press # and the display shows the new setting. Timers-Global (Default = 4 sec.) Output Trip Time (0305) This setting determines how long outputs are activated when tripped (if they are configured for a momentary response). ¾To set the RF Tx Timeout: 1. With the display showing RF TX TIMEOUT nn HOURS (current setting), enter the desired timeout value (2–24). The display flashes the entered setting. 2. Press # and the display shows the new setting. ¾To set the Output Trip Time: 1. With the display showing OUTPUT TRIP TIME nn SECS (current setting), enter the number of seconds (1–12). The display flashes the entered setting. 2. Press # and the display shows the new setting. Activity Timeout (0306) Timers-Global (Default = 24 hours) ¾To set the Activity Timeout: This setting determines when the system sends a “no activity” report. The panel can be set to wait from 1–42 hours. If no user interaction or 1. With the display showing ACTIVITY TIMEOUT device activation occurs in that time, the panel sends a report to the cennn HOURS (current setting), enter the number tral station. of hours (1–42). The display flashes the entered setting. 2. Press # and the display shows the new setting. Daylight Saving (0307) When this setting is on, the panel clock automatically adjusts for daylight saving time changes. Concord Timers-Global (Default = on) ¾To turn Daylight Saving off or on: 1. With the display showing DAYLIGHT SAVING OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. 40 The following sections describe the settings that appear under PARTITION 1-6. Timers-Partition 1-6 (Default = 30 sec.) Entry Delay (0310 - 0360) This setting determines how much time the user has to disarm the system (after entering the armed premises through a “designated delay door”) without causing an alarm. Note For UL 1023 Listed installations, the Entry Delay must be set to 45 seconds or less. The combined time for the Entry Delay and Dialer Abort Delay (02006) must not exceed 60 seconds. ¾To set the Entry Delay: 1. With the display showing ENTRY DELAY nnn SECS (current setting), enter the desired time value (30–240). The display flashes the entered setting. 2. Press # and the display shows the new setting. Timers-Partition 1-6 (Default = 60 sec.) Exit Delay (0311 - 0361) This setting determines how much time the user has (after arming the sys- ¾To set the Exit Delay: tem) to leave the premises through a “designated delay door” without 1. With the display showing EXIT DELAY nnn causing an alarm. SECS (current setting), enter the desired time value (45–184). The display flashes the Note entered setting. For UL 1023 listed installations, this feature must be set to 60 seconds or less. For UL 1610 listed installations, this feature must be set to 120 seconds or less. 2. Press # and the display shows the new setting. Timers-Partition 1-6 (Default = 4 min.) Extended Delay (0312 - 0362) This setting determines how much time the user has (after arming the sys- ¾To set the Extended Delay: tem) to enter or exit the premises through a “designated extended delay 1. With the display showing EXTENDED DELAY n door” (1–8 minutes). MINUTES (current setting), enter the desired time value (1–8). The display flashes the Note entered setting. For UL Listed installations Extended Delay may not be used. 2. Press # and the display shows the new setting. Siren Timeout (0313 - 0363) This setting determines how long sirens sound (1–30 minutes) if no one is present to disarm the system. Note For UL Listed installations, the Siren Timeout must be set to 4 minutes or more. Timers-Partition 1-6 (Default = 4 min.) ¾To set the Siren Timeout: 1. With the display showing SIREN TIMEOUT nn MINUTES (current setting), enter the desired time value (1–30). The display flashes the entered setting. 2. Press # and the display show the new setting. Sleep Time (0314 - 0364) Timers-Partition 1-6 (Default = 22:00 [10:00 pm]) This setting determines the start time and restart of a 10-hour window during which trouble beeps are suppressed. The initial occurrence of an event that causes trouble beeps within this window will not sound trouble beeps until the Sleep Time window expires. If trouble beeps from a previous event are due to be restarted during the sleep time window, they will be restarted one hour prior to Sleep Time. ¾To set the Sleep Time: 1. With the display showing SLEEP TIME hh:mm (current setting), enter the desired time value (00:0023:50 using 10 minute intervals). The display flashes the entered setting. 2. Press # and the display show the new setting. Note For UL listed installations, this feature must be set to off. ¾To turn off Sleep Time: 1. With the display showing SLEEP TIME hh:mm (current setting), press D. 41 Concord Timers-Partition 1-6 (Default = none) No Usage Time (0315 - 0365) Determines how many days a partition can remain disarmed before the panel sends a No Usage report to the central monitoring station and stores the event in the history buffer. When this feature is set: • • • This timer decreases by one at STIME each day the selected partition remains disarmed. If the timer gets to 0 at STIME, the panel sends a No Usage report to the central monitoring station and stores the event in the history buffer. If the partition is armed before the timer reaches 0, the timer resets to the programmed setting. ¾To set the No Usage Time: 1. With the display showing NO USAGE TIME (current setting), enter the desired number in days (2255). The display flashes the entered setting. 2. Press # and the display show the new setting. ¾To turn off No Usage Time: 1. With the display showing NO USAGE TIME (current setting), press D. When this feature is not set (default), the panel does not send or log No Usage reports. Light Control Menu Note For light control to work, the panel must be powered with a power line carrier transformer and X10 Powerhouse Lamp Modules must be installed at desired lamps. The LIGHT CONTROL menu lets you set up light activation for a specific partition. The following describes how to program the settings that appear under PARTITION 1-6. Light Control (Default = none) Entry Lights (0400 - 0450) This setting determines which X10 controlled lights turn on during entry and exit delays. Note X10 Lamp Modules set to 1 always turn on during the entry and exit delays. X10 Lamp Modules set to 2 always flash the arming level when arming the system. For example, lights flash two times when arming to STAY (level 2), and three times when arming to AWAY (level 3). ¾To set the Entry Lights: 1. With the desired partition selected, press #. The display shows ENTRY LIGHTS nnnnnnn (current setting). 2. Enter all the desired light numbers (3–9 based on the UNIT dial setting on each X10 Lamp Module). The display flashes the entered setting(s). Press # and the display shows the new setting(s). ¾To delete Entry Lights: 1. Enter any light number that appears on the display, then press #. The number disappears from the display. House Code (0401 - 0451) This setting enables X10 controlled lights to work in a selected partition without interfering with the X10 controlled lights of the other partitions. After setting the panel house code for each partition, you must set the X10 controlled lights for that partition to the same house code. The letter that appears automatically after the house code number indicates the necessary HOUSE dial setting for X10 modules in that partition. Concord Light Control (Defaults: partition 1=01-B, partition 2=02-C, partition 3=03-D, partition 4= 04-E, partition 5=05-F, partition 6=06-G) ¾To set the House Code: 1. With the desired partition selected, press A or B until the display shows HOUSE CODE nn-x (current setting). 2. Enter the desired number (1–255). The display flashes the entered number. Press # and the display shows the new house code. 42 Touchpad Options Menu The TOUCHPAD OPTIONS menu lets you set up touchpad panic and arming operation. The following section describes the settings that appear under GLOBAL. Touchpad Options-Global (Default = none) Latchkey Zones (0500) This setting defines the range of keychain touchpads that will function as a latchkey user. The value entered in this section can be any valid zone number. When a zone number is entered, all zones at or below that zone number will function as a latchkey user. For example, if 5 is entered, any keychain touchpads learned into zones 1–5 will be latchkey users and all others (6–96) will not. ¾To set the number of Latchkey Zones: 1. With the display showing LATCHKEY ZONES nnn (current setting), enter the desired number of latchkey zones (1–96). The display flashes the entered setting. 2. Press # and the display shows the new setting. ¾To delete/disable Latchkey Zones: 1. With the display showing LATCHKEY ZONES nnn (current setting), press D. The following sections describe the settings that appear under PARTITION 1-6. Fire Panic (0510 - 0560) This setting determines whether touchpad fire panic buttons are enabled (on) or disabled (off). Aux. Panic (0511 - 0561) This setting determines whether touchpad auxiliary panic buttons are enabled (on) or disabled (off). Police Panic (0512 - 0562) This setting determines whether touchpad police panic buttons are enabled (on) or disabled (off). Keychain TP Arm (0513 - 0563) Touchpad Options-Partitions 1-6 (Default = on) ¾To change the Fire Panic setting: 1. With the display showing FIRE PANIC OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. Touchpad Options-Partitions 1-6 (Default = on) ¾To change the Auxiliary Panic setting: 1. With the display showing AUXILIARY PANIC OFF/ ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. Touchpad Options-Partitions 1-6 (Default = on) ¾To change the Police Panic setting: 1. With the display showing POLICE PANIC OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. Touchpad Options-Partitions 1-6 (Default = off) When this setting is on, pressing the lock button on keychain touch- ¾To change the Keychain Touchpad Arming setting: pads arms the system directly to AWAY with NO DELAY. 1. With the display showing KEYCHAIN TP ARM OFF/ON (current setting), press 1 (off) or 2 (on). The display When this setting is off, each key-press increments the arming level flashes the entered setting. (i.e., from OFF to STAY, from STAY to AWAY). 2. Press # and the display shows the new setting. 43 Concord Star Is No Delay (0514 - 0564) This setting determines whether the keychain touchpad star button controls an output (off) or the No Delay feature (on). Touchpad Options-Partitions 1-6 (Default = off) ¾To change the keychain Star Is No Delay setting: 1. With the display showing STAR IS NO DELAY OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. Reporting Menu The REPORTING menu lets you set up which system events are reported to the central monitoring station. The following describes how to program the settings that appear under GLOBAL. 24-Hour Tamper (06000) When this setting is on, the panel sounds sirens and reports a tamper alarm (even when the system is disarmed), when wireless sensor tamper switches are activated. Note For commercial UL Listed installations (UL 1610) the 24-Hour Tamper must be set to on. Antenna Tamper (06001) Determines whether the panel monitors for antenna tamper of all connected receivers and transceivers. If this setting is on and 24-Hour Tamper is on, the panel sounds sirens in partition 1 only and reports an antenna tamper alarm. Other partitions show a trouble condition. Reporting-Global (Default = off) ¾To turn 24-Hour Tamper off or on: 1. With the display showing 24 HOUR TAMPER OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. Reporting-Global (Default = off) ¾To turn Antenna Tamper off or on: 1. With the display showing ANTENNA TAMPER OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. If this setting is off, the panel ignores antenna tampers. Buffer Control (06002) When this setting is on, only arming level changes and time changes (system time and daylight savings time) are logged in the buffer (memory) of the panel. When this setting is off, all system events are logged in the buffer. Back In Service (06003) When this setting is on, the panel reports to the central station when AC and backup battery power are restored (after an extended power outage). Concord Reporting-Global (Default = off) ¾To turn Buffer Control off or on: 1. With the display showing BUFFER CONTROL OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. Reporting-Global (Default = on) ¾To turn Back In Service reports off or on: 1. With the display showing BACK IN SERVICE OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. 44 Bypass Reports (06004) When this setting is on, the panel reports to the central station whenever sensors or zones are bypassed. Low CPU Battery (06005) When this setting is on, the panel reports a low panel battery to the central station before shutting down. If this feature and the Aux Power Fail feature are both on, the panel also monitors for and reports a low battery for the SuperBus 2000 2-Amp Power Supply. Note For UL 1635 listed installations, the Low CPU Battery feature must be set to on. Battery Restoral (06006) If this setting is on, the panel reports to the central monitoring station when a wireless sensor or touchpad reports a battery replacement to the panel. Buffer Full Rpt (06007) When this setting is on, the panel sends an “event buffer full” report to the central monitoring station when the event buffer logs 225 entries. When turned off, no report is sent. Zone Restorals (06008) When this setting is on, the panel reports a restoral to the central monitoring station for wireless or hardwire zones in alarm before the alarm is canceled. Note As with all GE Interlogix panels, hardwire smoke detectors connected to Concord or SnapCard hardwire zones do not send restorals. Two Trip Error (06009) Reporting-Global (Default = off) ¾To turn Bypass Reports off or on: 1. With the display showing BYPASS REPORTS OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. Reporting-Global (Default = on) ¾To turn Low CPU Battery reports off or on: 1. With the display showing LOW CPU BATTERY OFF/ ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. Reporting-Global (Default = off) ¾To turn Battery Restoral reports off or on: 1. With the display showing BATTERY RESTORAL OFF/ ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. Reporting-Global (Default = off) ¾To turn Buffer Full Report off or on: 1. With the display showing BUFFER FULL RPT OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. Reporting-Global (Default = off) ¾To turn Zone Restoral reporting off or on: 1. With the display showing ZONE RESTORALS OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. Reporting-Global (Default = off) This setting works with the Alarm Verify setting (see “Alarm Verify” later in this sec- ¾To turn Two Trip Error off or on: tion and Appendix B: Table B1 “Sensor Table Characteristics”). If Alarm Verify is 1. With the display showing TWO on, then the panel waits for a second sensor trip before sending an alarm. TRIP ERROR OFF/ON (current setting), press 1 (off) or 2 (on). The Note display flashes the entered setFor UL Listed installations, the Two Trip Error feature must be set to off. ting. If Two Trip Error is also on and a second sensor trip does not occur within a 4-minute 2. Press # and the display shows the time period, then the panel sends an error report to the central monitoring station. new setting. 45 Concord TP Panic RPT FMT (06010) This setting determines how the panel formats touchpad panic alarm reports to the central station. When this feature is turned on, touchpad panic alarms report using the following 3-digit codes: Auxiliary—597, Police—598, Fire—599 Reporting-Global (Default = off) ¾To turn TP Panic RPT FMT off or on: 1. With the display showing TP PANIC RPT FMT OFF/ ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. When turned off, touchpad panic alarms report using a 3-digit code from 500 to 515, with the last 2 digits identifying the touchpad device number. AC Failure (06011) When this setting is on, the panel reports to the central station at a random time between 15 and 45 minutes after AC power to the panel is lost. Making the report random helps prevent systems in a power outage affected area from trying to report at the same time. Note If this feature and the Aux Power Fail feature are both on, the panel also monitors for and reports an AC failure for the SuperBus 2000 2-Amp Power Supply. Reporting-Global (Default = off) ¾To turn AC Failure reports off or on: 1. With the display showing AC FAILURE OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. Note For UL Listed installations, AC Failure must be set to on. Receiver Failure (06012) When this setting is on, the panel reports a receiver failure under the following conditions: • • No wireless sensor signals have been received for two hours or The receiver is being jammed with a constant signal. Reporting-Global (Default = off) ¾To turn Receiver Failure reports off or on: 1. With the display showing RECEIVER FAILURE OFF/ ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. Note For UL Listed installations using wireless devices, Receiver Failure must be set to on. RF Low Bat Rpt (06013) This setting determines whether the panel sends daily or weekly low battery reports to the central monitoring station when a wireless device is reporting a low battery condition to the panel. RF Supv Report (06014) This setting determines whether the panel sends daily or weekly reports to the central monitoring station when the panel detects a supervisory condition in a wireless device. Concord Reporting-Global (Default = weekly) ¾To set RF Low Battery Report to daily or weekly: 1. With the display showing RF LOW BAT RPT DAILY/ WEEKLY (current setting), press 1 (daily) or 2 (weekly). The display flashes the entered setting. 2. Press # and the display shows the new setting. Reporting-Global (Default = weekly) ¾To set RF Supv Report to daily or weekly: 1. With the display showing RF SUPV REPORT DAILY/ WEEKLY (current setting), press 1 (daily) or 2 (weekly). The display flashes the entered setting. 2. Press # and the display shows the new setting. 46 Swinger Limit (06015) Reporting-Global (Default = 1) This setting determines the maximum number of times (1–2) a sensor or zone can go into alarm (during a single arming period) before the panel automatically bypasses that sensor or zone. This feature only applies to sensors or zones in groups 00–20, 29, 34, or 35. ¾To set the Swinger Limit: 1. With the display showing SWINGER LIMIT n (current setting), press the desired number (1–2). The display flashes the entered setting. 2. Press # and the display shows the new setting. When set to 1, the panel automatically bypasses a sensor or zone after it causes an alarm. When set to 2, the panel waits until a sensor or zone has caused a second alarm (during the same arming period) before bypassing it. At any setting, the automatic bypass is logged into the event buffer. A bypassed sensor or zone will be cleared (automatically unbypassed) if the system receives no further activations from that sensor or zone over the next 48–50 hours. Changing the arming level also clears all automatically bypassed sensors and zones and resets the Swinger Limit count on all sensors and zones. Aux Power Fail (06016) Reporting-Global (Default = off) When this setting is on, the panel sends a report to the central mon- ¾To turn Program Report on or off: itoring station if the 12 VDC power outputs on the panel and/or 1. With the display showing AUX POWER FAIL ON/OFF SuperBus 2000 2-Amp Power Supply fail. (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. Note 2. Press # and the display shows the new setting. If this feature is on and the AC Failure and Low CPU Battery features are both on, the panel sends AC failure and low backup battery reports for the SuperBus 2000 2-Amp Power Supply. The following describes the settings that appear under REPORTING—PARTITION 1-6. Opening Reports (06100 - 06600) When this setting is on, the panel sends an opening report to the central station after disarming the system. Note To use this feature, the Open/Close Reports settings under the PHONES menu must be turned on for the specific CS Phone or Pager number. Closing Reports (06101 - 06601) When this setting is on, the panel sends a closing report to the central station after arming the system. Note To use this feature, the Open/Close Reports settings under the PHONES menu must be turned on for the specific CS Phone or Pager number. Recent Closings (06102 - 06602) When this setting is on, the panel sends a recent closing report to the central station if an alarm occurs within two minutes after the exit delay time expires. Such a report is used to identify a possible exit fault. 47 Reporting-Partition 1-6 (Default = off) ¾To turn Opening Reports off or on: 1. With the display showing OPENING REPORTS OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. Reporting-Partition 1-6 (Default = off) ¾To turn Closing Reports off or on: 1. With the display showing CLOSING REPORTS OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. Reporting-Partition 1-6 (Default = on) ¾To turn Recent Closings off or on: 1. With the display showing RECENT CLOSINGS OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. Concord No Activity (06103 - 06603) Reporting-Partition 1-6 (Default = off) When this setting is on, the panel sends a no activity report to the cen- ¾To turn No Activity reports off or on: tral station when the activity timeout expires (see TIMERS—ACTIVITY TIM- 1. With the display showing NO ACTIVITY OFF/ON EOUT). (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. Reporting-Partition 1-6 (Default = off) Duress Option (06104 - 06604) (Default = off) When this setting is on, the system can be controlled using a programmed duress code (see SECURITY—PARTITION N—DURESS CODE) and will send a duress alarm to the central monitoring station. Note For UL Listed installations, Duress Option must be set to off. ¾To turn Duress Option off or on: 1. With the display showing DURESS OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. Do not use a duress code unless it is absolutely necessary. Using duress codes often results in false alarms due to code entry errors. If a duress code is absolutely necessary, use it with the audio verification module to reduce false alarms and accidental dispatches. Force Armed (06105 - 06605) Reporting-Partition 1-6 (Default = off) ¾To turn Force Armed off or on: 1. With the display showing FORCE ARMED OFF/ON (current setting), Note press 1 (off) or 2 (on). The display Forced arming occurs if the user presses BYPASS when arming the system with open sensors/zones protesting. flashes the entered setting. 2. Press # and the display shows the Auto-forced arming occurs when the user does not press BYPASS when arming the sysnew setting. tem with open sensors/zones protesting, then leaves through an entry/exit door and the When this setting is on, the panel reports to the central monitoring station when a user “force arms” the system. arming protest period expires. This causes the system to automatically bypass the open (protesting) sensors. Auto-forced arming always reports to the central monitoring station. Latchkey Format (06106 - 06606) (Default = off) This setting determines whether the selected partition is set up for basic (off) or advanced (on) latchkey opening report operation. Basic: If the partition is armed by entering 2 (or 3) + CODE, disarming using a designated latchkey user code or keychain touchpad within an assigned time schedule sends a page. If the partition is armed by entering 2 (or 3) + CODE + 6 (Latchkey), disarming using a designated latchkey user code or keychain touchpad inside or outside of an assigned time schedule sends a page. Reporting-Partition 1-6 (Default = off) ¾To turn Latchkey Format off or on: 1. With the desired partition selected, press A or B until the display shows LATCHKEY FORMAT OFF/ON (current setting). 2. Press 1 (off—basic) or 2 (on— advanced). The display flashes the entered setting. Press # and the display shows the new setting. Advanced: If the partition is armed by entering 2 (or 3) + CODE + 6 (Latchkey), disarming using a latchkey designated user code or keychain touchpad within an assigned time schedule sends a page. Refer to the User’s Guide for complete Latchkey setup and operation. Concord 48 Freeze Alarm (06107 - 06607) Reporting-Partition 1-6 (Default = off) This setting determines whether the panel reports a freeze alarm to the ¾To turn Freeze Alarm reporting off or on: central station or pager, when the selected partition’s energy saver mod- 1. With the desired partition selected, press A or B ule or Dialog RF Thermostat detects a temperature that matches a preuntil the display shows FREEZE ALARM OFF/ON determined setting (see BUS DEVICES—UNIT ID—ENERGY OPTIONS— (current setting). FREEZE TEMP, or FREEZE TEMP below). 2. Press 1 (off) or 2 (on). The display flashes the entered setting. Press # and the display shows the new setting. Freeze Temp (06108 - 06608) This setting determines the temperature point the Energy Saver Module or Dialog RF Thermostat detects a potential freeze (heating failure) condition. The adjustable range is from 40° - 90° F. Note This is the same menu found under ACCESSORY MODULES/BUS DEVICES/UNIT ID/ENERGY OPTIONS. The setting is used by both the SuperBus 2000 Energy Saver Module and Dialog RF Thermostat. Individual freeze temperature settings for each device are not allowed. Reporting-Partition 1-6 (Default = 42°F) ¾To set the Freeze Temp: 1. With the desired partition selected, press A or B until the display shows FREEZE TEMP (current setting). 2. Enter the desired temperature (40-90). The display flashes the entered setting. Press # and the display shows the new setting. Reporting-Partition 1-6 (Default = off) Alarm Verify (06109 - 06609) This setting determines whether the panel reports to the central monitoring station after a single sensor or zone trip (off) or waits for a second trip before reporting (on). This setting affects sensors/zones in groups 10 through 20. If Alarm Verify is set to on, group 18 responds the same as group 17 (see “Appendix B, Table B1 “Sensor Group Characteristics”). ¾To turn Alarm Verify off or on: 1. With the display showing ALARM VERIFY OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. Note For UL Listed installations, Alarm Verify must be set to off. System Tamper (06110 - 06610) This setting determines how the panel handles possible tamper situations. When this feature is on, the panel reacts in the following two ways: • • • Initiates an alarm if several attempts are made to disarm the system with incorrect access codes (40 consecutive keypresses). Reports to the central station if a bus device stops communicating with the panel. Reporting-Partition 1-6 (Default = off) ¾To change the System Tamper setting: 1. With the display showing SYSTEM TAMPER OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. Reports to the central monitoring station if a tamper condition occurs on unarmed RF (wireless) devices. Note For UL Commercial Listed installations (UL 1610), System Tamper must be set to on. 49 Concord Report Confirm (06112 - 06612) Reporting-Partition 1-6 (Default = off) ¾To change the Report Confirm setting: When this setting is on, system status speakers announce “Report is okay” followed by a single beep each time a successful report is made to the central moni- 1. With the display showing REPORT toring station. When turned off, no status message or beep sounds. CONFIRM OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. Siren Options Menu The SIREN OPTIONS menu lets you set up siren operation and supervision. The following describes how to program the settings that appear under GLOBAL. Immediate Beeps (0700) This setting determines whether the panel activates trouble beeps as soon as a wireless device supervisory condition is detected (on), or if the panel waits 10 hours after the supervisory condition is detected to activate trouble beeps (off). (Refer to TIMERS—GLOBAL—SUPERVISORY TIME). Siren Options-Global (Default = off) ¾To turn Immediate Beeps off or on: 1. With the display showing IMMEDIATE BEEPS OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. Note For UL Listed installations, this feature must be on. Disable Trouble Beeps (0701) When this setting is on, the panel does not initiate beeps to alert users of wireless device supervisory trouble and does not protest on arming if the condition exists. Note If Immediate Beeps is set to on, trouble beeps sound for supervisory trouble conditions regardless of this menu setting. Siren Options-Global (Default = off) ¾To turn Disable Trouble Beeps off or on: 1. With the display showing DISABLE TR BEEPS OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. Note For UL Listed installations, Disable Trouble Beeps must be set to off. UL 98 Options (0702) This setting determines whether the panel complies with UL 98 requirements (4-hour trouble beep restart, 4-hour backup battery test, 4-hour smoke (group 26) zone supervisory). Note For UL Listed installations, this feature must be on. Global Fire (0703) This setting determines whether or not sirens in all partitions sound (on) if any partition activates a fire alarm. Concord Siren Options-Global (Default = off) ¾To turn UL 98 Options off or on: 1. With the display showing UL 98 OPTIONS OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. Siren Options-Global (Default = off) ¾To turn Global Fire off or on: 1. With the display showing GLOBAL FIRE OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. 50 Siren Options-Global (Default = off) Silent Panic (0704) ¾To turn Silent Panic off or on: 1. With the display showing GLOBAL SILENT PANIC OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. This setting determines whether touchpad police panic alarms are audible (off) or silent (on). The following describes the settings that appear under SIREN OPTIONS—PARTITION 1. Siren Options-Partition 1 (Default = off) Siren Verify (0710) This setting determines whether or not the panel supervises the panel speaker terminals (7–8). When this feature is on, the panel will indicate a trouble condition if no speaker is connected to panel speaker terminals. Note For UL Listed installations, Siren Verify must be set to on. ¾To turn Siren Verify off or on: 1. With the display showing SIREN VERIFY OFF/ ON (current setting), press 1 (off) or 2 (on). The display flashes the entered setting. 2. Press # and the display shows the new setting. Sensors Menu The SENSORS menu gives you access to the following settings: • • • • LEARN SENSORS lets you add (learn) hardwire zones, wireless sensors, and wireless touchpads into panel memory. SENSOR TEXT lets you “name” the sensors and zones you have added to the system. DELETE SENSORS lets you delete zones and sensors from panel memory. EDIT SENSORS lets you view and, if desired, change a sensor group or partition assignment. You can also identify whether a zone is wireless or hardwire, whether it is configured as Normally Closed (N/C) or Normally Open (N/O), or if the zone is a touchpad. Table 6: How to Trip Sensors Sensor Steps to Trip Sensor Hardwire Zones Start with the zone in its “normal” state, then trip the zone into its alarm state. A normally closed door, for example, should be closed when you begin the Learn Sensors process. To trip the zone, open the door. Wireless Sensors Follow the instructions included with each sensor. Wireless Door/Window Sensors Place the external contact in the alarm condition, then activate with External Contacts the sensor tamper switch. Self Actuated Bell Activate the tamper switch. Handheld Wireless Touchpads Press the BYPASS button. Keychain Touchpads Press and hold the lock and unlock buttons together until the touchpad LED flashes. 1. ELM Keychain Touchpads 2. 3. 51 Press and release the unlock button twice quickly, then press and hold until the LED flashes three times. Press and release the unlock button once quickly, then press and hold until the LED flashes two times. Press and hold the unlock button until the LED flashes once. Concord The following describes how to program the sensor settings that appear under LEARN SENSORS. Sensors (Default = none) Learn Sensors (080) The following describes how to add (learn) hardwire zones and wireless devices into panel memory. Note The panel comes with factory programmed onboard hardwire zones. Install 2k-ohm, end of line (EOL) resistors on all unused factory programmed onboard hardwire zones. If you don’t want to install EOL resistors, delete any unused zones from memory. See Table 7 for onboard hardwire zone factory programming. Sensors must be placed in a partition or sensor group. To change the sensor group or partition assignment after adding a sensor or zone, use the EDIT SENSORS menu. ¾To Learn Sensors into panel memory: 1. With the display showing SENSORS, press # and the display shows LEARN SENSORS. 2. Press # and the display shows SENSOR PTN 1. 3. Press # to select partition 1 or press 2, 3, 4, 5, or 6 + # to select the desired partition. The display should show SENSOR GROUP 0. 4. Enter the desired sensor group + # (see Table B1 in “Appendix B” for a description of all sensor group characteristics). The display shows TRIP SENSOR nn, where nn is the displayed (next available) sensor number. 5. To change the displayed sensor number, enter the desired sensor number + #. The desired sensor number is displayed. 6. With the desired sensor number displayed, use the guidelines in Table 6 to force the sensor or zone you are adding (learning) into the panel memory to send a signal to the panel. 7. To add another sensor to the same sensor group and partition, go back to step 5. 8. To add sensors to another sensor group or partition, press * twice and go back to step 1 (LEARN SENSORS). Table 7: Onboard Hardwire Zone Factory Programming Zone Input Group No. & Description 1 10–Entry/Exit 2 17–Instant Interior Follower 3 13–Instant Perimeter 4 13–Instant Perimeter 5 13–Instant Perimeter 6 13–Instant Perimeter 7 13–Instant Perimeter 8 13–Instant Perimeter Note If the panel memory is cleared, all onboard hardwire zone factory programming will be erased. Concord 52 Sensor Text (081) Sensors (Default = none) Use the following guidelines to “name” zone and sensor locations: • • • • • Use the item numbers that appear in Appendix B, Table B2 “Item Numbers and Sensor Text” for characters and words listed there. If a desired word does not appear in Table B2, create it using the characters (custom text). When using words from Table B2, spaces between them appear automatically. When using characters from Table B2 to create words, you must reserve an item number for a ‘space’ after the word. Each character or word uses up one item number. For example, a word from the list counts as one item number. A created word (such as BOY’S) counts as six item numbers—4 letters, 1 apostrophe, and 1 space. Only 16 item numbers are allowed for each zone or sensor name, so plan ahead before programming sensor text. You may need to abbreviate words to avoid running out of item numbers. Delete Sensors (082) Note Deleting sensors does not delete sensor text associated with the deleted sensor number. To delete sensor text, enter the SENSOR TEXT menu and enter 000 (nulls) for each item number. This menu lets you view and, if desired, change the group and partition assignment for each learned zone or sensor. For example, the display shows: S01 P1 G13 NC HW BACK DOOR. Where: S01 = zone/sensor number, P1 = partition 1, G13 = sensor group 13, NC = normally closed, HW = hardwired, and BACK DOOR is the programmed text name. Other description codes include, RF = wireless sensor, TP = touchpad, NO = normally open. 53 TEXT FOR SN 01 FRONT ENTRY DOOR Sensors (Default = none) The following procedure describes how to remove hardwire zone and wireless sensor numbers from panel memory. Edit Sensors (083) ¾To program Sensor Text: 1. Press A or B until the display shows SENSOR TEXT. 2. Press # and the display shows TEXT FOR SN 01. 3. Press A or B until the display shows the desired sensor number (or enter the desired sensor number and press #). 4. Press # and the display shows: SN 1 ITEM 0 0 - ________. Where ITEM 0 is the first character/word location and 0 is the character/word number. 5. Enter the number of the desired character or word, or scroll through the numbers by pressing B (forward) or A (backward). If you make a mistake, simply enter the correct number or continue scrolling through choices. 6. Press # to accept the displayed choice and the display shows: SN 1 ITEM 1 0 -.____ 7. Repeat steps 5 and 6 as needed to complete the zone or sensor name. 8. Press * after entering the last character or word number. The display shows the complete text name. For example: ¾To Delete Sensors from panel memory: 1. Press A or B until the display shows DELETE SENSORS. 2. Press # and the display shows DELETE SENSOR nn (lowest zone/sensor number in panel memory). 3. Press # to delete the displayed sensor or—enter the desired sensor number, then press #. 4. Repeat steps 2 and 3 until all desired sensors are deleted. Sensors (Default = none) ¾To Edit Sensors: 1. Press A or B until the display shows EDIT SENSORS. 2. Press # and the display shows the sensor or zone with the lowest number. 3. Press A or B to scroll through all learned zones and sensors. 4. When the desired zone or sensor is displayed, press #. The display shows SENSOR PTN n (current partition assignment). 5. Enter the desired partition number, then press #. The display shows the new partition assignment. 6. Press A or B and the display shows SENSOR GROUP nn (current group assignment). 7. Enter the desired group number, then press #. The display shows the new group assignment. Concord Audio Verification Menu The AUDIO VERIFICATION menu lets you set up the audio verification module (AVM) operation in partition 1. If you want audio verification for partitions 2-6, you must install a “stand-alone” audio verification module and a 4-Relay Output Module (HOM) (60-770) output for that partition. The following describes the Audio Verification settings that appear under PARTITION 1. Audio Verification-Partition 1 (Default = off) Audio Verify (09000) This setting determines whether or not the system can be accessed by phone for alarm verification. ¾To turn Audio Verification off or on: 1. With the display showing AUDIO VERIFICATION, press #. The display shows PARTITION 1. 2. Press # again and the display shows AUDIO VERIFY OFF/ON (current setting). 3. Press 1 (off) or 2 (on). The display flashes the entered setting. Press # and the display shows the new setting. Audio Mode (09001) Audio Verification-Partition 1 (Default = 1) This setting determines how the audio verification module operates. Choose one of the following: ¾To set Audio Mode: 1. With the display showing AUDIO VERIFY OFF/ON, press A or B until the display shows AUDIO MODE nn (current setting). 2. Enter the desired mode number (1–3). The display flashes the entered setting. Press # and the display shows the new setting. • • • (1) Instant—Allows the central station operator instant access for an audio session by entering the AVM code or by pressing * (if an AVM access code is not programmed) upon completion of panel alarm report (also see ACCESS TIMEOUT). (2) Callback—Allows the central station operator to place a call to the premises within 5 minutes of the alarm report (panel picks up after one ring). The operator must press * or enter the AVM access code within 20 seconds after ring. The panel does not report any alarms during the AVM session, except for fire alarms. (3) Callback Silent—Same as Callback, except premises phones do not ring. Fire Shutdown (09002) This setting determines whether system sirens turn off during a fire alarm audio session. Silent Talkback (09003) This setting determines whether the central station operator can speak to persons on the premises (on) or only listen (off) during a silent or duress alarm audio session. Concord Audio Verification-Partition 1 (Default = off) ¾To turn Fire Shutdown off or on: 1. With the display showing AUDIO VERIFY OFF/ON, press A or B until the display shows FIRE SHUTDOWN OFF/ON (current setting). 2. Press 1 (off) or 2 (on). The display flashes the entered setting. Press # and the display shows the new setting. Audio Verification-Partition 1 (Default = off) ¾To turn Silent Talkback off or on: 1. With the display showing AUDIO VERIFY OFF/ON, press A or B until the display shows SILENT TALKBACK OFF/ON (current setting). 2. Press 1 (off) or 2 (on). The display flashes the entered setting. Press # and the display shows the new setting. 54 Access Timeout (09004) Audio Verification-Partition 1 (Default = 90 sec.) If the Audio Mode is set to “Instant,” then this set- ¾To change the Access Timeout: ting determines how much time (30–300s, in 2-sec- 1. With the display showing AUDIO VERIFY OFF/ON, press A or B until ond increments) the central station operator has to the display shows ACCESS TIMEOUT nn SECS (current setting). enter the AVM access code after the panel is 2. Enter the desired time. The display flashes the entered setting. Press # accessed for an audio session. and the display shows the new setting. Beep Delay (09005) This setting determines how long AVM access beeps are delayed (0–300s, in 2-second intervals) at the beginning of a 2-way audio session. Access Code (09006) This setting determines the code required to access the audio verification module to start an audio session. If no code is programmed, pressing * starts an audio session. Audio Verification-Partition 1 (Default = 02 sec.) ¾To change the Beep Delay: 1. With the display showing AUDIO VERIFY OFF/ON, press A or B until the display shows BEEP DELAY nn SECS (current setting). 2. Enter the desired time. The display flashes the entered setting. Press # and the display shows the new setting. Audio Verification-Partition 1 (Default = **** or none) ¾To change the Access Code: 1. With the display showing AUDIO VERIFY OFF/ON, press A or B until the display shows ACCESS CODE nnnn (current code). 2. Enter the desired 4-digit access code. The display flashes the entered code. Press # and the display shows the new setting. ¾To delete an Access Code: 1. With the display showing AUDIO VERIFY OFF/ON, press A or B until the display shows ACCESS CODE nnnn (current code). 2. Press D to delete. Vox Mic Gain (09007) This setting determines the microphone sensitivity for triggering voice-activated switching (VOX). For the Interrogator 200, the default setting (14) is recommended. Room size, acoustics and furnishings where the Interrogator 200 is located will influence the setting. Setting range is from 01 (low) to 64 (high). Vox Gain Range (09008) This setting determines the gain range for voiceactivated switching (VOX). Setting range is from 01 (low) to 64 (high). For best results, this setting should be higher than the Vox Mic Gain. Manual Mic Gain (09009) Audio Verification-Partition 1 (Default = 14) ¾To change the Vox Mic Gain: 1. With the display showing AUDIO VERIFY OFF/ON, press A or B until the display shows VOX MIC GAIN nn (current setting). 2. Enter the desired 2-digit setting (01 - 64). The display flashes the entered setting. Press # and the display shows the new setting. Audio Verification-Partition 1 (Default = 64) ¾To change the Vox Gain Range: 1. With the display showing AUDIO VERIFY OFF/ON, press A or B until the display shows VOX GAIN RANGE nn (current setting). 2. Enter the desired 2-digit setting (01 - 64). The display flashes the entered setting. Press # and the display shows the new setting. Audio Verification-Partition 1 (Default = 64) Not field programmable at this time. 55 Concord Audio Verification-Partition 1 (Default = 04) Vox RX Gain(09010) This setting determines the receiver (talkback) gain level for voice-activated switching (VOX). Setting range is 01-10. If the VOX is switching the speaker on when the central station operator is not talking, lower this setting and the VOX Mic Gain setting. ¾To change the VOX RX Gain: 1. With the display showing AUDIO VERIFY OFF/ON, press A or B until the display shows VOX RX GAIN nn (current setting). 2. Enter the desired 2-digit setting (01 - 10). The display flashes the entered setting. Press # and the display shows the new setting. If the VOX is not switching the speaker on when the central station operator is talking, raise this setting and lower the VOX Mic Gain setting. Accessory Modules Menu The ACCESSORY MODULES menu gives you access to the following menus: • BUS DEVICES—this menu lets you read bus device unit numbers, assign bus devices to a par- • SNAPCARDS—this menu lets you set the configuration number for each SnapCard output, tition, and configure other features associated with a specific bus device. assign SnapCard outputs to a partition, and name the SnapCard outputs. The following describes how to program the settings that appear under ACCESSORY MODULES— BUS DEVICES. Acc. Modules-Bus Devices (Default = **** or none) Unit-ID (10000 thru 10015) This menu lets you identify all connected bus devices, view each Unit Number, view the Device ID number, and configure other settings based on a specific device. This menu also lets you delete learned bus devices. Note Most settings under ACCESSORY MODULES—BUS DEVICES have no shortcut numbers. To help identify bus devices, the 8-digit Device ID number is also located on a label on each SuperBus 2000 device. Device ID This menu lets you change the bus device ID number when replacing a defective bus device. Concord ¾To identify bus device Unit and ID: 1. With the display showing BUS DEVICES, press #. The display shows the bus Unit Number and the 8-digit Device ID number. For example: UNIT - ID 0—02110185. Where 0 is the Unit Number and 02110185 is the Device ID number. 2. Press A or B to identify all other bus Unit Numbers (0–15) and Device ID numbers. ¾To delete learned Unit Numbers: 1. With the display showing BUS DEVICES, press #. The display shows the bus device set to Unit Number 0. 2. Press A or B until the bus device Unit Number you want to delete is displayed. 3. Press D. The display changes the Unit Number to NONE. Acc. Modules-Bus Devices-Unit ID-Change ID (Default = none) ¾To change a Device ID: 1. With the display showing the desired bus device, press # + #. The display shows DEVICE ID (current ID). 2. Enter the ID of the new bus device. The display flashes the entered selection. Press # and the display shows the new setting. 3. Exit programming mode. 4. Remove AC and battery power from the panel. 5. Replace the defective bus device with a new one. 6. Apply AC and battery power to the panel. 56 Acc. Modules-Bus Devices-Unit ID-Device Partition Partition Assign This menu lets you assign bus devices to work in the desired partition. Note SuperBus 2000 8Z Input Modules, SuperBus 2000 4-Relay Output Modules, and SuperBus 2000 RF Receivers are not assigned to partitions. ¾To assign bus devices to partitions: 1. With the display showing the desired bus device, press #. 2. Press A or B until the display shows DEVICE PTN and then press #. The display shows PARTITION ASSIGN n. 3. Press 1-6 to select the desired partition. The display flashes the entered selection. Press # and the display shows the new setting. Output Programming Acc. Modules-Unit ID-Outputs Use these settings to program the output points of any installed SuperBus 2000 Hardwire Output Module. The installer programs a HOM output point into the Concord security panel by entering three kinds of information. Below describes how to program each of the HOM output point configurations into the security panel. The point configuration number is tttrr, where ttt is the trigger number and rr is the response number. • • 1. 2. 3. 4. • Partition -the system partition (1-6). Trigger - the event that activates the output point. Trigger events can be partition alarms, trouble conditions, open sensors, etc. (see Appendix B: Reference Tables). Response - how the output responds when trigger event occurs (see Appendix B: Reference Tables). Note HOM output points cannot be configured for user control. Only the onboard and SnapCard outputs can be configured for user control. 5. 6. 7. 8. With the display showing the desired bus device, press #. Press A or B until the display shows OUTPUTS. Press #. The display shows OUTPUT 1. Press A or B to select an output, then press #. The display shows PARTITION ASSIGN 1. Press 1-6 to select the desired partition assignment for this relay. The display flashes the entered setting. Press # and the display shows the new setting. Press A or B. The display shows CONFIGURATION tttrr (current setting). Enter the desired 5-digit configuration number for this relay. The display flashes the entered setting. Press # and the display shows the new setting. Press # and repeat steps 4 through 8 until all outputs are programmed Status Beeps Acc. Modules-Bus Devices-Unit ID-Keypad Options (Default = on) ¾To turn touchpad Status Beeps on or off: 1. With the display showing the desired touchpad, press # then A or B until the display shows KEYPAD OPTIONS. This feature is usually turned off for a touchpad that is located in or near bedrooms, to avoid disturbing sleeping per- 2. Press # and the display shows STATUS BEEPS OFF/ON (current setting). sons. 3. Press 1 (off) or 2 (on) to select the desired setting. The disNote play flashes the entered selection. Press # and the display For UL Listed installations, Status Beeps must be set to on. shows the new setting. This setting determines whether or not the selected touchpad sounds status beeps. Each touchpad can be set individually. Key Beeps Acc. Modules-Bus Devices-Unit ID-Keypad Options (Default = on) ¾To turn Key Beeps on or off: 1. With the display showing the desired touchpad, press # then A or B until the display shows KEYPAD OPTIONS. This feature is usually turned off for a touchpad that is Next, press # then A or B until the display shows KEY located in or near bedrooms, to avoid disturbing sleeping perBEEPS OFF/ON (current setting). sons. 2. Press 1 (off) or 2 (on) to select the desired setting. The display flashes the entered selection. Press # and the display shows the new setting. This setting determines whether or not selected touchpads beep when their buttons are pressed. 57 Concord Acc. Modules-Bus Devices-Unit ID-Energy Options (Default = 42°F) Freeze Temp This setting determines the temperature point that the Energy ¾To change the Freeze Temp setting: Saver Module detects a potential freeze (heating failure) con- 1. With the display showing the desired bus device press #, dition. The adjustable range is from 40° to 90°F. then A or B until the display shows ENERGY OPTIONS. Next, press # then A or B until the display shows FREEZE Note TEMP nn DEGREES (current setting). This is the same menu found under REPORTING/PARTITIONS 1-6. The setting is used by both the SuperBus 2000 Energy 2. Enter the desired freeze temperature (40°–90° F). The disSaver Module and Dialog RF Thermostat. Individual freeze templay flashes the entered selection. Press # and the display perature settings for each device are not allowed. shows the new setting. Acc. Modules-Bus Devices-Unit ID-Energy Options (Default = none) Temperature This setting lets you adjust the Energy Saver Module (ESM) room temperature setting to match the premises thermostat. The adjustable range is from 40°–90°F. Note To ensure accuracy, wait at least 15 minutes before setting the ESM temperature to allow the ESM to warm or cool to actual room temperature. ¾To change the ESM Temperature setting: 1. With the display showing the desired bus device press #, then A or B until the display shows ENERGY OPTIONS. Next, press # and then A or B until the display shows TEMPERATURE nn DEGREES (current setting). 2. Enter the desired temperature (40°–90° F). The display flashes the entered selection. Press # and the display shows the new setting. Acc. Modules-Bus Devices-Unit ID-Cellular Options (Default = B) Cellular System This setting determines the cellular transmission system (A or B) used for cellular communication. This information is provided by the cellular provider based on installation ZIP code. ¾To set the Cellular System: 1. With the display showing the desired bus device press 1, (B) or 2 (A). The display flashes the entered selection. 2. Press # and the display shows the new setting. The following describes how to program the settings that appear under SNAPCARDS. Acc. Modules-SnapCards-Output Programming (Defaults: Partition Assign=1, Configuration Output 1= 01400, Output 2 = 00410, Output 3 = 00903, Output 4 = 01003) Output Programming (output 1: partition assign-101100, configuration-101101; output 2: partition assign-101110, configuration101111; output 3: partition assign-101120, configuration-101121; output 4: partition assign-101130, configuration-101131) This setting lets you assign a partition and a 5-digit configuration number for each SnapCard relay output. This number determines both which system event activates the output and the duration or time the output is activated. 1. 2. Assign the partition (1-6). Assign the configuration number (combination of a trigger number and a response number. Trigger: the event that activates the output point. Trigger events can be partition alarms, trouble conditions, open sensors, etc. (see Appendix B: Reference Tables). Response: how the output responds when trigger event occurs (see Appendix B: Reference Tables). Concord ¾To assign configuration numbers to SnapCard Relay outputs (where tttrr is the point configuration number, ttt is the trigger number and rr is the response number): 1. 2. 3. 4. 5. 6. 7. With the display showing SNAPCARDS, press #. Then press A or B until the display shows OUTPUT PROGRAMMING. Press # again and the display shows OUTPUT 1. Press A or B to select the desired output (1–4), then press #. With the display showing PARTITION ASSIGN 1, press 1-6 to select the desired partition. Press # to confirm the partition. Press A or B until the display shows CONFIGURATION tttrr (current setting). Enter the desired 5-digit configuration number for this relay. Press # to confirm the setting. Press # and repeat steps 3 through 6 until all outputs are programmed. 58 Output Text (output 1: 10120, output 2: 10121, output 3: 10122, output 4: 10123) Acc. Modules-SnapCards-Output Text (Default = none) ¾To program Output Text: 1. With the display showing SNAPCARDS, press #, then A or B until the display shows OUTPUT TEXT. 2. Press # and the display shows OUTPUT 1. • Use the item numbers that appear in “Appendix B, Table 3. Press A or B until the desired output number is disB2” for characters and words listed there. played. Note 4. Press # and the display shows: OUTPUT N ITEM 0 0 If you desire an output for User Output Control you must use the .Where ITEM 0 is the first character/word location and 0 Output Text feature to name the output. If no Output Text is prois the character/word number. grammed, the user will not have access to the output. 5. Enter the number of the desired character or word, or scroll • If a desired word does not appear in Table B2, create it through the numbers by pressing B (forward) or A (backusing the characters (custom text). ward). If you make a mistake, simply enter the correct • When using words from Table B2, spaces between them number or continue scrolling through choices. appear automatically. When using characters from Table B2 6. Press # to accept the displayed choice and the display to create words, you must reserve an item number for a shows: OUTPUT N ITEM 1 0 -. ‘space’ after the word. 7. Repeat steps 4 and 5 as needed to complete the output • Each character or word uses up one item number. For examname. ple, a word from the list counts as one item number. A cre8. Press * after entering the last character or word number. ated word (such as BOY’S) counts as six item numbers—4 The display shows the complete text name. For example: letters, 1 apostrophe, and 1 space. OUTPUT 1 GARAGE DOOR. • Only 16 item numbers are allowed for each output name, so plan ahead before programming output text. You may need to abbreviate words to avoid running out of item numbers. Entering text for an output allows the user to control it directly or by schedule. Use the following guidelines to “name” SnapCard outputs: Onboard Options Menu The ONBOARD OPTIONS menu lets you set up the following built-in options: • • • INPUTS—This menu lets you turn the Smoke Verification and the Two Wire Smoke features off or on. OUTPUT PROGRAMMING—This menu lets you set configuration numbers for the two built-in panel outputs and assign the outputs to partitions. OUTPUT TEXT—This menu lets you assign text to the two built-in outputs so they can be controlled by the user. The following sections describe the settings that appear under ONBOARD OPTIONS—INPUTS. Smoke Verify (1100) This setting controls the number of sensor group 26 (fire) zone trips needed to report a fire alarm. • Hardwire Smokes: will determine whether or not the panel requires two alarm signals within five minutes (on) from 2wire smoke detectors connected to panel zone input 8 and/or SnapCard zone inputs or any other hardwire zone learned into group 26 (fire) before activating system sirens and reporting to a central station (or pager). • Wireless Smokes: the first trip of a group 26 RF sensor will cause a local fire alarm. The second trip of any group 26 zone within the siren timeout will cause that fire alarm to be reported to the central station. Onboard Options-Inputs (Default = off) ¾To turn Smoke Verify off or on: 1. With the display showing ONBOARD OPTIONS, press # twice. The display shows SMOKE VERIFY OFF/ON (current setting). 2. Press 1 (off) or 2 (on). The display flashes the entered number. 3. Press # and the display shows the new setting. Note For California State Fire Marshall Listed installations, this feature must be off. Note RF smoke detectors repeat the alarm transmission every 60 seconds as long as they are detecting smoke. This repeated transmission will serve as the second zone trip, causing the alarm to be reported. 59 Concord Onboard Options-Inputs (Default = off) Two Wire Smoke (1101) This setting determines how onboard hardwire zone 8 is configured. When this setting is on, zone 8 will be configured for two wire smoke detectors. When off, it will be configured for a normal hardwire input. ¾To turn Two Wire Smoke off or on: 1. With the display showing ONBOARD OPTIONS, press # twice. The display shows SMOKE VERIFY OFF/ON (current setting). 2. Press A or B until the display shows TWO WIRE SMOKE ON/OFF (current setting). 3. Press 1 (off) or 2 (on). The display flashes the entered number. Press # and the display shows the new setting. The following sections describe the settings that appear under ONBOARD OPTIONS—OUTPUT PROGRAMMING. Output 1, 2 (Output 1: partition assign-11100, configuration-11101; Output 2: partition assign11110, configuration-11111) This setting lets you assign the partition and the 5-digit configuration number for the two onboard outputs. The configuration number determines • • which system event activates the selected output, and the duration or time the output is activated. The first three digits represent the trigger number of an event (such as triggering an alarm, opening a sensor, or arming the system). The last two digits represent how the output responds (such as momentary switching, maintained (or latched) switching, or switching for a preset time). Onboard Options-Output-Programming (Defaults: Output 1=Ptn 1, 01614; Output 2=Ptn 1, 01710) ¾To set up onboard Output 1 & 2 partition and configuration assignments: 1. 2. 3. 4. 5. 6. Note If you want to configure an output for user Output Control you must use the Output Text feature to name the output. If no Out7. put Text is programmed, user Output Control will not function for that output. With the display showing ONBOARD OPTIONS, press # + B. The display shows OUTPUT PROGRAMMING. Press # and the display shows OUTPUT 1. Press B to select OUTPUT 2. Press # and the display shows PARTITION ASSIGN n (current setting). Press 1-6 to assign the output to the desired partition, then press #. The display shows PARTITION ASSIGN (new setting). Press B and the display shows CONFIGURATION tttrr (current setting). Enter the desired configuration number. The display flashes the entered number. Press # and the display shows the new setting. Press # and repeat steps 2 through 6 until all outputs are programmed. Use the system event trigger and response numbers listed in Appendix B: Reference Tables. Concord 60 Output Text (Output 1: 1120, Output 2: 1121) Onboard Options-Output Text-Output 1, 2 (Default = none) ¾To program Output Text: 1. With the display showing ONBOARD OPTIONS, press # then press B twice and the display shows OUTPUT TEXT. 2. Press # and the display shows OUTPUT 1. • Use the item numbers listed in “Appendix B, Table 3. Press # and the display shows: OUTPUT 1 ITEM 0 0 -. Where B2” for characters and words. ITEM 0 is the first character or word location and 0 is the Note character or word number. If you want to configure an output for user Output Control you must use the Output Text feature to name the output. If no Out- 4. Enter the number of the desired character or word, or scroll put Text is programmed, Output Control will not function for through the numbers by pressing B (forward) or A (backthat output. ward). If you make a mistake, simply enter the correct number or continue scrolling through choices. • If a desired word does not appear in Table B2, create it 5. Press # to accept the displayed choice and the display shows: using the characters (custom text). Entering text for an output allows the user to control it directly or by schedule. Use the following guidelines to “name” onboard outputs: • • • When using words from Table B2, spaces between 6. them appear automatically. When using characters 7. from Table B2 to create words, you must reserve an item number for a ‘space’ after the word. Each character or word uses up one item number. For example, a word from the list counts as one item number. A created word (such as BOY’S) counts as six item numbers—4 letters, 1 apostrophe, and 1 space. Only 16 item numbers are allowed for each output name, so plan ahead before programming output text. You may need to abbreviate words to avoid running out of item numbers. OUTPUT 1 ITEM 1 0 -. Repeat steps 4 and 5 as needed to complete the output name. Press * after entering the last character or word number. The display shows the complete text name. For example: OUTPUT 1 GARAGE DOOR. Macro Keys Menu The MACRO KEYS menu lets you set up single-button system commands with the ATP2100 and ATP2600 touchpads. The following describes how to program the settings that appear under PARTITION 1-6. Macro Keys This menu lets you program the Chime, Stay, Exit, and Away macro keys on ATP2100 and ATP2600 touchpads. Macro keys let you perform a system command with one button, eliminating manual entry of the command. For example, the Stay key can be programmed so that it automatically arms the system to level 2 with No Delay just by pressing it once. • • • Each partition can accept up to four macros. All touchpads in a partition use the same set of macros. Macro keys can execute a system command up to 14 keypresses in length. Use keys 0-9, #, *, and A-F to program macros. Note It is recommended not to program macros that disarm the system. • • • 61 Panic keys, long keypresses (press and hold), and macro keys themselves cannot be used in a macro. When programming a macro to enter user programming, two delays (F key) must be entered after the access code, and before any shortcut number. For example, the macro key sequence for entering the Set Time menu would be 9CODEFF020. When using an ATP2100 or ATP2600 to jump to another partition, pressing the macro buttons on the “jumped” touchpad will execute macro commands based on the macros programmed in the jumped partition. Macro Keys (Defaults for all partitions: Macro Key 1—Chime: 71 Macro Key 2—Stay: 2 Macro Key 3—Quick Exit: D; Macro Key 4—Away: 3) ¾To program/change a Macro Key: 1. With the display showing MACRO KEYS, press #. The display shows PARTITION 1. 2. Press A or B to select the desired partition (1-6), then press #. The display shows MACRO KEY 1 (current setting). 3. Press A or B to select the desired macro key you want to program (1-4). 4. To change this macro, press the associated macro key. The current setting disappears and is replaced with a flashing cursor. 5. Enter the desired system command. The display flashes the entry. Note If you make a mistake, press the macro key twice to clear the entry and start over. 6. Press the macro key again to accept the entered command. The display stops flashing. Concord Exiting Programming Mode After all installer/dealer programming is completed, use the following procedure to exit programming mode. ¾To exit programming mode: 1. Press * until the display shows SYSTEM PROGRAMMING. 2. Press A or B until the display shows EXIT PROGRAMMING READY. 3. Press # and the touchpad displays the TIME AND DATE. Entering Quick Programming Mode The Quick Programming Mode allows basic system programming using a SuperBus 2000 Fixed Display Touchpad or any SuperBus 2000 Alphanumeric Touchpad. The following menus are accessible: • • • • • Account Number (all partitions) CS Phone 1 CS Phone 2 CS Phone 3 Learn Sensors—limited to selecting sensor number, sensor group, and partition assignment. An alphanumeric touchpad is required for programming sensor text in standard programming mode. ¾To enter Quick Programming Mode: 1. Make sure the system is disarmed in all partitions. 2. Press 8 + installer/dealer CODE + 03. The display shows ACCOUNT NUMBER. 3. Cycle through the menus as shown below: ACCOUNT NUMBER #dc · B` _A CS PHONE #dc Partition n 1 -6 #dc · CS Phone 1 · #dc Acct. Number 00000 · CS Phone None #dc B` _A · CS Phone 2 #dc · CS Phone None #dc B` _A · CS Phone 3 #dc B` _A LEARN SENSOR · END PROGRAMMING #` #dc Sensor Partition n 1 -6 · CS Phone None B` _A · #dc Sensor Group 0 · #dc Trip Sensor n 1-96 Entering User Programming Mode The user programming mode lets you view system version information and program the following system settings: • • • • • • • • Time and Date User Codes Options Set Up Schedules Attach Schedules to Events Energy Saver Attach Lights to Sensors System Version You can enter user programming from an alphanumeric or fixed display touchpad by using the system or partition master code. The default system master code is 1234. ¾To enter user-programming mode: Press 9 + CODE. The display shows TIME AND DATE. Concord 62 Time and Date Menu Note Setting the time and date is important for accurate tracking of system events stored in the event buffer. The panel uses a global clock and calendar for time and date. Alphanumeric touchpads display the panel time and date whenever the system is disarmed. The TIME AND DATE menu lets you set this clock and calendar. The following procedures tell you how. Time and Date (Default = 00:00) Time (020) This setting lets you adjust the panel clock to the correct time. The panel uses a 24-hour clock. For example, to set the time to 4:17 P.M., enter 1617. ¾To set the Time: 1. With the display showing TIME AND DATE, press # and the display shows TIME hh:mm (current time). 2. Enter the correct time (0000–2359). The display flashes the entered time. Press # and the display shows the new time. Time and Date (Default = 01/01/00) Date (021) This setting lets you adjust the panel calendar to the correct month, day, and year. ¾To set the Date: 1. With the display showing TIME AND DATE, press #, then A or B until the display shows DATE nn/nn/nn (current date). 2. Enter the correct month (01–12), day (01–31), and year (00–99). For example, enter 090100 for September 1, 2000. The display flashes the entered date. Press # and the display shows the new date. User Codes Menu The USER CODES menu lets you program/change regular user access codes, partition master codes, and the system master code. You can enter up to 230 separate user codes, allowing up to 230 different “users” access to the security system. You can also specify whether or not a specific user is able to perform specific actions like, bypass sensors or test the system. User NNN (030nnn0 where nnn=user number 00-229) User Codes-Reg. User Codes-User NNN (Default = none) User codes perform basic arming and disarming functions. The system allows up to 230 user codes (user numbers 00–229). User numbers that show **** indicate no code is currently programmed for that user number. ¾To program Regular User Codes: 1. With the display showing USER CODES, press # and the display shows REGULAR USER CODES. 2. Press # and the display shows USER nnn (first available user number). 3. Press A or B to select the desired user number, then press #. The display shows USER nnn - nnnn. 4. With the desired user number displayed, enter a 4-digit user code. The display flashes the entered code. Press # and the display shows USER nnn - nnnn (new code). ¾To delete Regular User Codes: 1. With the display showing USER CODES, press # and the display shows REGULAR USER CODES. 2. Press # and the display shows USER nnn - nnnn (first available user number). 3. Press A or B to select the desired user number/user code you want to delete (if it is not already displayed), then press #. The display shows USER nnn - nnnn. 4. Enter the system or partition master code. The display flashes the entered code. Press # and the display shows USER nnn -- **** (no code). 63 Concord Direct Bypassing (030nnn1 where nnn=user number 00-229) This setting determines whether a specific user code provides access to the “bypass sensors” feature. Set this feature to “on” for all users who need to be able to bypass sensors. Remote Access (030nnn2 where nnn=user number 00-229) This setting determines whether the user can access the panel from a remote phone (a phone located off the premises). System Tests (030nnn3 where nnn=user number 00-229) This setting determines whether a specific user code provides access to the phone and sensor tests. Set this feature to “on” for all users who need to be able to conduct phone and sensor tests. Latchkey Report (030nnn4 where nnn=user number 00-229) This setting determines whether the user code causes a latchkey report to be sent to a pager when the code is used to change arming levels. Concord User Codes-Reg. User Codes-User NNN (Default = off) ¾To turn user code Direct Bypassing off or on: 1. With the display showing USER CODES, press # and the display shows REGULAR USER CODES. 2. Press # and the display shows USER nnn (first available user number). 3. Press A or B to select the desired user number, then press #. The display shows USER nnn - nnnn. 4. Press A or B until the display shows DIRECT BYPASSING OFF/ON (current setting). 5. Press 1 (off) or 2 (on). The display flashes the entered setting. Press # and the display shows the new setting. User Codes-Reg. User Codes-User NNN (Default = off) ¾To turn user code Remote Access off or on: 1. With the display showing USER CODES, press # and the display shows REGULAR USER CODES. 2. Press # and the display shows USER nn (first available user number). 3. Press A or B to select the desired user number, then press #. The display shows USER nnn - nnnn. 4. Press B until the display shows REMOTE ACCESS ON/OFF (current setting). 5. Press 1 (off) or 2 (on). The display flashes the entered setting. Press # and the display shows the new setting. User Codes-Reg. User Codes-User NNN (Default = off) ¾To turn user code System Tests off or on: 1. With the display showing USER CODES, press # and the display shows REGULAR USER CODES. 2. Press # and the display shows USER nnn (first available user number). 3. Press A or B to select the desired user number, then press #. The display shows USER nnn - nnnn. 4. Press A or B until the display shows SYSTEM TESTS OFF/ON (current setting). 5. Press 1 (off) or 2 (on). The display flashes the entered setting. Press # and the display shows the new setting. User Codes-Reg. User Codes-User NNN (Defaults: 00-05 = on, 06-229 = off) ¾To assign the Latchkey Report attribute to user codes: 1. With the display showing USER CODES, press # and the display shows REGULAR USER CODES. 2. Press # and the display shows USER nnn (first available user number). 3. Press A or B to select the desired user number, then press #. The display shows USER nnn - nnnn. 4. Press A or B until the display shows LATCHKEY OFF/ON (current setting). 5. Press 1 (off) or 2 (on). The display flashes the entered setting. Press # and the display shows the new setting. 64 Partition Assign (030nnn5 where nnn=user number 00-229) This setting determines which partitions a user code can access. A code can be assigned to all partitions if desired, making it usable at any touchpad in any partition and able to jump to any selected partition. User Codes-Reg. User Codes-User NNN (Default = Ptn 1) ¾To assign Partitions to a user code: 1. With the display showing USER CODES, press # and the display shows REGULAR USER CODES. 2. Press # and the display shows USER nnn (first available user number). 3. Press A or B to select the desired user number, then press #. The display shows USER nnn - nnnn. 4. Press A or B until the display shows PARTITION ASSIGN (current setting). 5. Enter the desired partitions (1-6). The display flashes the entered numbers. Press # and the numbers stop flashing. User Codes-Partition Master Code (Default = none) Partition Master (0310 - 0315) The Partition Master Code provides access to all system ¾To change the Partition Master Code: operations and user programming for a single partition. 1. With the display showing USER CODES, press # then A or B until the display shows PARTITION MASTER CODE. Note You must be “in” the partition of the partition master code 2. Press # and the display shows PARTITION nnnn (current code). you wish to change. 3. Enter a new 4-digit code. The display flashes the entered code. Press # and the display shows the new code. System Master (0320) User Codes-System Master Code (Default = 1234) The System Master Code provides access to all system operations and user programming. ¾To change the System Master Code: 1. With the display showing USER CODES, press # then A or B until the display shows SYSTEM MASTER CODE. 2. Press # and the display shows SYSTEM MASTER nnnn (current code). 3. Enter a new 4-digit code. The display flashes the entered code. Press # and display shows the new code. Options Menu The OPTIONS menu lets you set up the system for downloading and silent arming. You can also adjust alphanumeric touchpad display brightness from this menu. Downloading (041) When this setting is on, the panel can communicate with Enterprise Downloader software for programming the system from off-site. Note For this feature to work, the panel must be connected to a phone line and be programmed with REMOTE ACCESS on, with a Downloader phone number, and with a Downloader code. Silent Arming (042) This setting determines whether the panel sounds status beeps from sirens and the touchpad when the system is armed. Note When this feature is on, the user does not need to press 5 (SILENT) before arming the system to prevent status sounds. When SIA False Alarm Reduction (0004) is ON, this option is not available. 65 Options (Default = on) ¾To turn Downloading off or on: 1. Press A or B until the display shows OPTIONS. 2. Press #, then A or B until the display shows DOWNLOADING OFF/ON (current setting). 3. Press 1 (off) or 2 (on). The display flashes the entered selection. Press # and the display shows the new setting. Options (Default = off) ¾To turn Silent Arming off or on: 1. Press A or B until the display shows OPTIONS. 2. Press #, then A or B until the display shows SILENT ARMING OFF/ON (current setting). 3. Press 1 (off) or 2 (on). The display flashes the entered selection. Press # and the display shows the new setting. Concord Options (Default = 2) Touchpad Brightness (043) This setting lets the user lighten or darken the background on touchpad displays. Each touchpad can be set to compensate for lighting conditions in the touchpad location. Volume (044) ¾To adjust Touchpad Brightness: 1. Press A or B until the display shows OPTIONS. 2. Press #, then A or B until the display shows TOUCHPAD BRIGHTNESS n (current setting). 3. Enter a setting from 0 (darkest background) to 3 (brightest background). The display flashes the entered selection. Press # and the display shows the new setting. Options (Default = 4) ¾To adjust status sound Volume: This setting determines the volume level of status sounds from speakers connected to the Phone Interface/ 1. Press A or B until the display shows OPTIONS, then press #. Voice Module. 2. Next, press A or B until the display shows VOLUME n (current setting). Note This menu appears only if a Phone Interface/Voice Module 3. Enter a setting from 0 (off) to 7 (loudest). The display flashes the is connected to the panel. entered selection. Press # and the display shows the new setting. Options (Default = on) Voice Chime (045) This setting determines whether speakers connected to the Phone Interface/Voice Module announce perimeter sensor/zone numbers that are tripped when the Chime feature is on. For example, “Sensor one open.” Note This menu appears only if a Phone Interface/Voice Module is connected to the panel. ¾To turn Voice Chime off or on: 1. Press A or B until the display shows OPTIONS. 2. Press # then A or B until the display shows VOICE CHIME OFF/ ON (current setting). 3. Press 1 (off) or 2 (on). The display flashes the entered selection. Press # and the display shows the new setting. Chime On Close (046) Options (Default = off) When this setting is on, the panel sounds a single chime when a perimeter door or window is closed. ¾To turn Chime On Close off or on: 1. Press A or B until the display shows OPTIONS. 2. Press # then A or B until the display shows CHIME ON CLOSE OFF/ON (current setting). 3. Press 1 (off) or 2 (on). The display flashes the entered selection. Press # and the display shows the new setting. Set Up Schedules Menu The SET UP SCHEDULES menu lets you set up time frames for light control, output control, automatic arming, latchkey times, and exception opening/closing reports. The system (all partitions) allows you to set up to 16 schedules (00–15) which are shared by all partitions. Setting up schedules consists of setting a start and stop time for each schedule, then selecting which days of the week the schedule will be active. You can also set up a rollover schedule, which starts on one day and ends on another day. This saves programming time and leaves more schedules available (in case they are needed later). Rollover Schedule Example: To set up a schedule to rollover from Tuesday evening to Wednesday morning, set a schedule start time for 2200 (10:00 P.M.) and a stop time for 0500 (5:00 A.M.). Set the schedule to turn on Tuesday. Because the stop time is set for morning, the system automatically carries the schedule over to the next day. If you use the same start and stop times described above and set the schedule to turn on Monday through Friday, then one schedule will cover the entire week. Concord 66 (Default = 00:00) Set Up Schedules (05XXY, where XX=schedule 00-15 and Y=start [0]/stop[1] Monday thru Sunday [2-8]) This menu lets you set up start/stop times for each day of the week. Schedules used by one partition cannot be viewed or changed from a different partition. Note If you are programming schedules for your customer, be sure to record the settings in the User’s Manual. ¾To set up a Time Schedule: 1. Press A or B until the display shows SET UP SCHEDULES. 2. Press # and the display shows SCHEDULE 00. If you want a different schedule number, press A or B until the desired schedule number appears. 3. Press # and the display shows START TIME hh:mm (current setting). 4. Enter the desired starting time (00:00–23:59). The display flashes the entered time. Press # and the display shows START TIME hh:mm (new setting). 5. Press B and the display shows STOP TIME hh:mm (current setting). 6. Enter the desired stop time (00:00–23:59). The display flashes the entered time. Press # and the display shows STOP TIME hh:mm (new setting). 7. Press B and the display shows MONDAY OFF/ON (current setting). To select a different day, continue pressing B until the desired day appears. 8. Press 1 (off) or 2 (on). The display flashes the entered selection. Press # and the display shows the new setting for the selected day. 9. Repeat steps 7 and 8 until all desired settings for each day are set. Attach Schedules to Events Menu The ATTACH SCHEDULES TO EVENTS menu lets you link the following system events to time schedules: • • • • • • • Latchkey Opening—sends a report if system is disarmed within the attached time schedule. Latchkey Closing—sends a report if system is armed within the attached time schedule. Exception Opening—sends a report if system is not disarmed within the attached time schedule. Exception Closing—sends a report if system is not armed within the attached time schedule. Lights (1–9) activate X10 controlled lights by the attached time schedule. Outputs (1–6) allow users to attach onboard (1–2) and SnapCard outputs to a schedule. Arming—Allows the user to arm the panel at the schedule start time. Latchkey Reports (Opening: 060nn, Closing: 061nn, where nn=Schedule number [0 to 15]) This setting lets you attach the Latchkey Opening report feature and the Latchkey Closing report feature to time schedules. 67 Attach Schedules to Events (Default = off) ¾To Attach a Schedule to Latchkey Opening or Latchkey Closing: 1. Press A or B until the display shows ATTACH SCHEDULES TO EVENTS. 2. Press # then A or B until the display shows LATCHKEY OPENING OR LATCHKEY CLOSING. 3. Press # and the display shows SCHEDULE 00 OFF/ON (current setting). If you want a different schedule, press A or B until the desired schedule appears. 4. Press 1 (off) or 2 (on). The display flashes the entered selection. Press # and the display shows the new setting for the selected schedule. Concord Exception Reports (Opening: 062nn, Closing: 063nn, where nn=Schedule number [0 to 15]) This setting lets you attach the Exception Opening report feature and the Exception Closing report feature to time schedules. Lights (064xnn where nn=Schedule number [0 to 15] and x=light number [1 to 9] minus 1) This setting lets you attach light controls to a time schedule. Attach Schedules to Events (Default = off) ¾To Attach a Schedule to Exception Opening or Exception Closing: 1. Press A or B until the display shows ATTACH SCHEDULES TO EVENTS. 2. Press # then A or B until the display shows EXCEPTION OPENING OR EXCEPTION CLOSING. 3. Press # and the display shows SCHEDULE 00 OFF/ON (current setting). If you want a different schedule, press A or B until the desired schedule appears. 4. Press 1 (off) or 2 (on). The display flashes the entered selection. Press # and the display shows the new setting for the selected schedule. Attach Schedules to Events (Default = off) ¾To Attach Schedules to Lights: 1. Press A or B until the display shows ATTACH SCHEDULES TO EVENTS. 2. Press # then A or B until the display shows LIGHTS. Press # to enter the LIGHTS menu. 3. Press A or B until the desired light appears. 4. Press # and the display shows SCHEDULE 00 OFF/ON (current setting). If you want a different schedule, press A or B until the desired schedule appears. 5. Press 1 (off) or 2 (on). The display flashes the entered selection. Press # and the display shows the new setting for the selected schedule. 6. Repeat steps 3, 4, and 5 until all desired lights are attached to schedules. Outputs (065xnn where nn=Schedule number [0 to 15] and x=output number [1 to 6] minus 1) Attach Schedules to Events (Default = off) This setting lets you attach outputs to a time schedule. Onboard outputs are 1–2, SnapCard outputs are 3–6. ¾To Attach Schedules to Outputs: 1. Press A or B until the display shows ATTACH SCHEDULES TO EVENTS. 2. Press # then A or B until the display shows OUTPUTS. Press É to enter the OUTPUTS menu. 3. Press A or B until the desired output appears. 4. Press # and the display shows SCHEDULE 00 OFF/ON (current setting). If you want a different schedule, press A or B until the desired schedule appears. 5. Press 1 (off) or 2 (on). The display flashes the entered selection. Press # and the display shows the new setting for the selected schedule. 6. Repeat steps 3, 4, and 5 until all desired outputs are attached to schedules. Note Outputs can only be scheduled if text has been entered in installer programming. Only onboard and SnapCard outputs can be scheduled. Arming (0660nn where nn=Schedule number [0 to 15]) This setting lets you arm according to a time schedule. Note This setting will allow you to arm to AWAY only. There is no disarm schedule. Concord Attach Schedules to Events (Default = off) ¾To Attach Schedules to Arming: 1. Press A or B until the display shows ATTACH SCHEDULES TO EVENTS. 2. Press # then A or B until the display shows ARMING. 3. To select arm to AWAY press #. 4. Press # and the display shows SCHEDULE 00 OFF/ON (current setting). If you want a different schedule, press A or B until the desired schedule appears. 5. Press 1 (off) or 2 (on). The display flashes the entered selection. Press # and the display shows the new setting for the selected schedule. 6. Repeat steps 4 and 5 until all desired schedules are attached. 68 Energy Saver Menu The ENERGY SAVER menu lets you set the Energy Saver Module or Dialog RF Thermostat lowand high-setpoints. These setpoints override the premises thermostat allowing the Energy Saver Module or Dialog RF Thermostat to activate the furnace/air conditioner. Low Setpoint (070) Energy Saver (Default = 50°F) This setting determines the temperature at which the energy saver module relay closes to activate the furnace. Note The low setpoint cannot be set equal to or higher than the high setpoint. ¾To set the Low Setpoint: 1. With the display showing ENERGY SAVER, press #, then A or B until the display shows LOW SETPOINT NN DEGREES (current setting). 2. Enter the desired temperature (45–89°). The display flashes the entered setting. Press # and the display shows the new setting. Energy Saver (Default = 90°F) High Setpoint (071) This setting determines the temperature at which the energy saver module relay closes to activate the air-conditioner. Note The high setpoint cannot be set equal to or lower than the low setpoint. ¾To set the High Setpoint: 1. With the display showing ENERGY SAVER, press #, then A or B until the display shows HIGH SETPOINT nn DEGREES (current setting). 2. Enter the desired temperature (46–90°). The display flashes the entered setting. Press # and the display shows the new setting. Attach Lights to Sensors Menu The ATTACH LIGHTS TO SENSORS menu lets you assign a light number to a sensor. Each time the sensor is activated, the attached light will turn on for 5 minutes. When the 5 minute timer expires the light will turn off. If the same light is scheduled, it will only turn on during the schedule time. Light X to Sensor Y (08n where n=light number [1-9] minus 1) Attach Lights to Sensors (Default = 0) ¾To attach a light to a sensor: 1. With the display showing LIGHT 1 TO SENSOR y (current setting), press A or B to select the desired light number. 2. Enter the desired sensor number (01–96). The display flashes the entered setting. Press # and the display shows the new setting. Note The sensor must be learned into the current par- 3. Repeat steps 1 through 2 until all desired lights are attached to sensors. This menu attaches light x to sensor y. Each time a selected sensor is tripped, the selected light will turn on and a 5 minute timer will start. tition before it can be attached. 69 ¾To detach a light from a sensor: 1. With the display showing LIGHT 1 TO SENSOR y (current setting), press A or B to select the desired light number. 2. Enter 0 as the sensor number and press #. Concord System Version Menu The SYSTEM VERSION menu lets you view and identify panel hardware and software. This information is primarily used for troubleshooting purposes. (Default = N/A) System Version (Factory Code: 010, System Number: 011, System Level: 012) This menu lets you view and identify panel hardware and software version. ¾To view and identify the System Version: 1. Press A or B until the display shows SYSTEM VERSION. 2. Press # and the display shows FACTORY CODE nnn*nnnn. 3. Press B and the display shows SYSTEM NUMBER *nnnnnnn. 4. Press B again and the display shows SYSTEM LEVEL nnnn. 5. Press B again and the display shows SW VERSION nnnnx (panel firmware version). Downloader Programming The panel can be programmed remotely using Enterprise. Use the information you recorded in Appendix A to inform the downloading operator of the programming requirements for this system. Enterprise Downloader Programming Note A Downloader Phone Number must be programmed and the user-programmable option “Downloading” must be on for remote downloader programming to work. ¾To initiate a Enterprise download session: 1. Contact your download station and ask the operator to prepare to download to the panel. 2. Make sure the system is disarmed. 3. Press 8 + system master code + 7 + 0 (any), 1 (down), or 2 (up). The display shows SYSTEM DOWNLOAD IN PROGRESS during the downloading process. Testing the System This section describes the following: Note Before testing, it is recommended that you have covers on all modules (mounted outside the cabinet) and the panel cabinet door closed. The testing environment should match the system working environment. If the alphanumeric touchpad does not display SYSTEM DOWNLOAD IN PROGRESS, call the downloader operator to verify the downloader phone number. Also, make sure ToolBox is set up properly. Refer to the “Troubleshooting” section if the problem persists. • • • • • • • • • • Basic System Commands Testing Zones/Sensors Testing Phone Communication Testing Central Station Communication Testing Outputs and Sirens Testing Light Control Testing the Energy Saver Module Changing Fixed Display Touchpads Testing the Audio Verification Module Testing Cellular Backup Communication You should test the system after installing or servicing and after adding or removing devices from the system. Refer to the “Troubleshooting” section if correct test results are not achieved. Concord 70 Basic System Commands Table 8 describes basic touchpad operating commands. For complete details on system operation, including user programming, refer to the system User’s Manual. Table 8: Basic Touchpad Commands Command System Response * (STATUS) Indicates current system status *+* Indicates AC power, battery, and current system status 1 + CODE Disarms system to OFF 2 + CODE Arms system to STAY 3 + CODE Arms system to AWAY 2 (quick arm on) Arms system to STAY 3 (quick arm on) Arms system to AWAY 2 or 3 + CODE + 4 or 2 or 3 + 4 Arm system—No Delay (no exit or entry delay) 5 + 2 or 3 + CODE or 5 + 2 or 3 Arms system silently (no arming status beeps) 7+1 Turns chime feature on and off 7+2 Turns Energy Saver on and off 7+4 Partition jump without entering code (only if Partition Security option is off) 7+6 Identifies alarms in memory 7 + 7 + n (n = output number [1–6]) Turns the output on or off. (This command is only functional after output text is entered into panel 1–2 = onboard outputs memory.) 3–6 = module outputs 8 + CODE + 2 Initiates a phone test 8 + CODE + 3 Initiates a sensor test 8 + installer CODE + 3 Initiates a dealer sensor test 8 + CODE + 6 Partition jump 8 + CODE + 8 View Event History 0+0 Turns all controlled lights on and off 0 + n (n = light number 1-9) Turns individual controlled light on and off Testing Zones/Sensors Test sensors/zones after all programming is completed, whenever there is a change in environment, equipment, or programming, and whenever a zone- or sensor-related problem occurs. Note While the sensor test is a valuable installation and service tool, it only tests sensor operation for the current conditions. You should perform a sensor test after any change in environment, equipment, or programming. Note If you hear a long, lowpitched beep, proceed to the following section “If a Wireless Sensor Does Not Test.” 71 If the system does not respond as described in the following procedure, see the “Troubleshooting” section. 1. Place all sensors and zones in their non-alarm state. 2. At an alphanumeric touchpad, enter the sensor test mode by pressing 8 + installer code + 3. The touchpad sounds one beep and displays SENSOR TEST. The panel starts a 15 minute timer. 3. Trip each zone/sensor one at a time. Touchpads (and interior sirens) should sound one short, high-pitched beep and the display should show the sensor name (or number) and OK. 4. Press the STATUS button when you think all zones/sensors are tested. The touchpad displays any untested sensors/zones and touchpad panics. If all sensors/zones and touchpad panics have been tested, the display shows SENSOR TEST OK. 5. Test any untested zones/sensors and touchpad panics. 6. The system stays in sensor test mode for 15 minutes. When less than 5 minutes remain, touchpads and interior sirens beep and the panel announces the remaining time over the speakers once every minute. After 15 minutes the panel disarms to OFF, automatically. If you need more time to complete the sensor test, press 8 + installer CODE + 3 while the system is still in sensor test mode. This restarts the 15 minutes of test time. Concord 7. When all sensors/zones and touchpad panics have been tested, press 1 + installer CODE to exit sensor test mode. If a Wireless Sensor Does Not Test If touchpads display SENSOR FAILURE and sirens sound a long, low-pitched beep when a zone or sensor is tripped, this indicates that the wireless sensor signal strength is below acceptable limits. Distance from the receiver, the installation environment, or both, are most likely affecting the sensor signal strength. When possible, locate wireless sensors within 100 feet of the panel. While a transmitter may have a range of 1,000 feet or more out in the open, the environment at the installation site can have a significant effect on transmitter range. Refer to the “Troubleshooting” section to resolve the problem. For wireless sensors that don’t respond, use an RF Sniffer (60-401) test tool to verify that the sensor is transmitting. Constant beeps from the RF Sniffer indicate a runaway (faulty) sensor. Remove the sensor battery(s) and replace the sensor. Testing Phone Communication Perform a phone test to check the phone communication between the panel and the central monitoring station. ¾To perform a phone test: 1. Contact the central monitoring station to inform them that you are testing the system. 2. Press 8 + system master CODE + 2. The display reads PHONE TEST and the touchpad sounds one beep. When the panel completes the test, the system returns to the previous arming level automatically. If the display continues to show PHONE TEST for 1½ minutes or more, enter 1 + system master CODE and refer to the “Troubleshooting” section. Testing Central Station/Pager Communication After performing sensor and phone tests, check that the system is reporting alarms successfully to the central station or pager. ! Be sure to contact the central monitoring station before activating outputs that trigger from an alarm condition. Caution Note The way information is displayed varies with pager services and may not match the example above. Account numbers with alpha-characters also vary when displayed, depending on pager service. Account numbers are not displayed if STREAMLINING is turned on. ¾To test communication with the central station/pager: 1. Call the central station and tell the operator that you will be testing the system. 2. Arm the system. 3. Test each of the touchpad and wireless panic buttons and trip at least one sensor of each type (fire, intrusion, etc.) to verify correct operation. 4. Check pager displays to verify reports are received. Pagers display an event code, digit sensor number, and the last four digits of the account number. For example, a pager display of 999 002 7468 indicates the following: 999 = alarm condition, 002 = sensor/zone in alarm or user number, 7468 = last four digits of account number. 5. When you finish testing the system, call the central monitoring station to verify that the alarms were received. Table 9 describes pager system event codes. Concord 72 Table 9: Pager System Event Codes Code System Event 009 Zone Restoral 111 System Disarmed 115 Sensor Test Exit 118 Trouble condition cleared 119 Alarm Canceled 222 System Armed to STAY 333 System Armed to AWAY 555 Phone/Sensor Test 888 System Trouble Condition 999 System in Alarm Table 10 describes pager sensor/zone number and user number report codes. Table 10: Pager Sensor/Zone Code and Numbers Code 000 Sensor/Zone or User Number System event not caused by a zone or user 001–096 Sensor/Zone Numbers 1–96 600–829 Regular User Codes 0–229 used 846 System Master Code used 847 Installer Code used 848 Dealer Code used 850 Quick Arm used 851 Keyswitch Sensor used 852 System Armed Itself (during service or power-up) Testing Outputs and Sirens All outputs (onboard and SnapCard) should be tested to verify configuration programming. ! Be sure to contact the central monitoring station before activating outputs that trigger from an alarm condition. Caution ¾To test outputs: 1. Contact the central monitoring station to inform them you are testing the system. 2. Verify that all wiring at the panel and output devices is correct. 3. Activate the appropriate device to trigger each output as programmed. 4. Verify that each output responds according to the programmed configuration number. For outputs that trigger sirens, verify that the correct alarm sounds are produced from these sirens. Table 11 describes the system alarm sounds you should hear for each alarm event. 5. Contact the central monitoring station when you are finished testing. Table 11: System Alarm Sounds Alarm Type Fire Alarm Sound Repeating series of three beeps Police/Intrusion Continuous tone Auxiliary 73 Rapid beeps Concord Testing Light Control Test all lights plugged into X10 Lamp Modules to verify house code and light number settings. ¾To test light control: 1. Press 0 + 0 repeatedly to turn all lights on and off together. 2. Press 0 + 1 repeatedly to turn light 1 on and off. 3. Repeat step 2 for remaining lights (0 + 2 for light 2, 0 + 3 for light 3, etc.). 4. Arm the system to Away. All lights plugged into modules set to Unit 1 (or set as entry lights) should turn on and stay on for 5 minutes. All lights plugged into modules set to Unit 2 should blink three times to indicate the arming level. Remaining lights should not be affected. 5. Disarm the system. If Unit 1 (or entry) lights were on for an entry or alarm, they will turn off in 5 minutes. Unit 2 lights should blink once to indicate the system is off. Remaining lights should not be affected. 6. All lights should turn on and remain on during fire and auxiliary/medical alarms. All lights should flash during a police or intrusion alarm. Testing the Energy Saver Module (ESM) Note The system must have highand low-temperature limits set to test the Energy Saver Module. Note There is a 5-minute delay after the Energy Saver Module returns control to the furnace/AC before it will override the furnace/AC again. Test the Energy Saver Module to verify it overrides the thermostat. ¾To test the Energy Saver Module: 1. Press * (status) + * (status) to display the system status, ENERGY SAVER OFF, and the present TEMPERATURE nn°. The temperature displayed (and/or announced) should match the house thermostat. If the temperatures do not match, refer to the ACCESSORY MODULES—BUS DEVICES menu in the “Programming” section. 2. 3. Press 7 + 2 to turn on the ESM. The display shows ENERGY SAVER ON and the ESM relay will click once. Press 7 + 2 again to turn the ESM off. The display shows ENERGY SAVER OFF. Changing Fixed Display LCD Touchpad Chime and Trouble Beep Tones The frequency (pitch) of chime and trouble beep tones from a fixed display touchpad can be adjusted to a more desirable or distinct tone, or to compensate for hearing impaired persons. Note Chime and trouble beep tones sound using the default frequency during, or within 15 seconds of, any button activity at that specific touchpad. Note Vacuum fluorescent displays do not have a contrast adjustment. ¾To change status tone pitch: 1. Press and hold the * and 0 buttons together until you hear a steady tone, then release the buttons. 2. Press and hold 1 to lower the pitch or press and hold 2 to raise the pitch. 3. Release the button when the desired pitch is heard. After about 15 seconds of no touchpad activity, the steady tone stops sounding. Adjusting Touchpad Display Contrast Touchpad displays can be adjusted for easier viewing to help compensate for lighting conditions in the touchpad location. The contrast adjustment lightens or darkens the text. ¾To adjust display contrast: 1. Enter configuration mode by pressing the D and 6 buttons together for at least two seconds. The display shows DA nnn. 2. Press and release the 1 and 2 buttons together repeatedly, until the desired contrast level is displayed. 3. Press * and the display briefly shows DONE, then shows the time and date. Testing Audio Verification Module (AVM) Communication Test the Audio Verification Module from off-site and the central station to verify that it works properly. ¾To test the module from off-site: You will need a helper and touch-tone phone at an off-site location to perform this test. When testing the AVM from off-site the following guidelines must be followed. • Concord The Remote Access feature must be set to on (default). 74 • • • 1. 2. 3. 4. 5. 6. 7. The Audio Verify feature must be set to on. The system must be in a non-alarm state. Optional Ring/Hang/Ring feature must be on (default) to work with steps 1 and 2 below. Otherwise wait for 12 rings and the panel will pick up automatically. The off-site helper calls the panel, lets the phone ring twice, and hangs up. The helper must call the panel again in 10 to 40 seconds. The panel answers System hello. The helper dials the following on the phone, # 1234 # 8 (AVM access CODE) 5. The helper should now be able to hear you through the AVM. Walk through the vicinity of the AVM while speaking at a normal conversation level. Tell the helper to dial a 1 and speak to you. To return to listen mode, the helper dials a 3. When testing is complete, have the helper dial 99 and hang up. ¾To test the module with the central station: 1. Inform the central station that you will be sending an alarm and testing an AVM. 2. Give them the programming selections you made for the panel (see “Audio Verification Menu” for programming information). 3. Use a touchpad panic button to initiate an auxiliary alarm. 4. The central station operator waits for the alarm to be reported and initiates an audio session. 5. Walk through the vicinity of the AVM while speaking at a normal conversation level. 6. Have the operator speak to you. 7. When testing is complete, the operator will end the session. Testing Cellular Backup Communication Perform this test to check the cellular communication between the panel and the central monitoring station. ¾To test Cellular Communication: 1. Contact the central monitoring station to inform them that you are testing the system. 2. Install and activate the SuperBus 2000 Cellular Backup Module. 3. Verify or change the following CS PHONE 1 panel option settings shown in Table 12. Table 12: Current Phone Settings CS PHONE 1 Option Test Setting PHONE NUMBER Central station phone number HIGH LEVEL RPTS ON BACKUP OFF* CELLULAR BACKUP ON Previous Setting * Can be set to ON if no CS PHONE 2 PHONE NUMBER is programmed. Note If the current settings do not match the test settings, record the current settings (Table 12), so that they can be restored when this test is complete. 75 4. 5. 6. Disconnect the phone line by unplugging the Db-8 cord from the RL-31X Jack. Initiate a phone test (8 + System Master Code + 2). The phone test attempt should fail via the phone line within 5 minutes. The panel will emit a long low tone (and speak “phone failure 1” if so equipped). 7. Wait for the phone test to succeed via the cell backup. The panel should emit a short high tone (and speak “phone test ok” if so equipped). 8. Verify the CS report. 9. If success does not occur, verify that the signal strength (RSSI) shown on the Cellular Backup Module is acceptable and repeat steps 5-8. 10. Restore previous CS PHONE 1 settings if needed. Concord Troubleshooting Feature This section describes what to do if you experience problems with system operation. If after performing the troubleshooting procedures the panel still malfunctions, please call Technical Support at 1-800-777-2624. Problem Action/Solution Panel Power Panel does not power up. Touchpads don’t display or respond. 1. 2. 3. 4. 5. Verify that the panel transformer is plugged into an unswitched outlet. Check the AC circuit breaker to be sure the circuit is live. Check that the backup battery is installed correctly and the AC power transformer is plugged in. Check for proper panel and transformer wiring. Measure the incoming AC voltage at panel terminals 1 and 2. It should read about 16.5 VAC. No incoming AC voltage at panel terminals 1 and 2. 1. 2. 3. Unplug the AC power transformer and disconnect the wires from the transformer and the panel. Check transformer to panel wire for short or open circuits. Plug in the transformer and check for 16.5 VAC at the transformer unconnected terminals. If zero (0) volts, replace the transformer. Touchpad display indicates System Low Battery or voice sounds “System low battery.” 1. 2. 3. Check that the backup battery is installed correctly and the AC power transformer is plugged in. Measure the incoming AC voltage at panel terminals 1 and 2. It should read about 16.5 VAC. Check for 11.75 to 13.8 VDC battery voltage between the backup battery spade lugs. If the battery voltage is not within this range, replace the battery. Note When the panel is running a backup battery test, the reading at the connected battery can range from 11.2 to 13.5 VDC. The panel automatically runs a backup battery test under the following conditions: (1) on initial power-up, (2) during user sensor test, (3) once every minute when backup battery has failed, (4) once every 24 hours at the programmed STIME (UL 98 Options off) or once every 4 hours (UL 98 Options on). With the AC power transformer plugged in, the panel automatically charges the battery. While the battery is charging for the first time it is normal for the system to indicate System Low Battery. This can take a number of hours depending on the initial battery charge. Once the battery reaches 12.5 VDC (full charge as measured while in battery test), the condition clears. If the trouble condition persists after 24 hours, replace the backup battery. The touchpads flash AC or display AC Power Failure/AC Failure After pressing STATUS. (Panel continues to operate from backup battery). 1. 2. 3. 4. Check the AC circuit breaker to be sure the circuit is live. Check for proper panel and transformer wiring. Check that the transformer is plugged into a nonswitched outlet and secured with the provided screw. Check that the transformer is supplying AC to the panel. (Transformer internal fuse may be blown. ! Be careful when securing the transformer to an outlet with a metal cover. Hold the cover tightly in place. You could receive a serious shock if the metal outlet cover drops down onto the prongs of the plug while you are securing the transformer and cover to the outlet box. Warning Access Codes Customer cannot remember access code(s). 1. 2. 3. 4. Check your records to see if you have the customer’s access code(s) on file. Verify the access code(s) using the Downloader. Clear memory and reprogram the panel locally. Clearing the memory will erase onboard hardwire zone factory programming. Installer cannot remember install code. Concord 76 Feature Problem Action/Solution 1. 2. 3. Check your records to see if you have the install code on file. Verify the install code using the Downloader. Use the Dealer Code to enter program mode and view the installer code. Installer cannot remember dealer code. Check your records to see if you have the dealer code on file. Arming and Disarming System protests and won’t arm. 1. 2. 3. If arming to level 2, make sure all monitored perimeter doors and windows are closed. If arming to level 3, make sure all perimeter and interior sensors are closed. Press STATUS for an indication of the problem. System won’t disarm. 1. 2. 3. 4. Disarming using incorrect code. Enter correct code. Access code is not programmed or set up in user programming to disarm system. Wireless touchpad is not learned into system or hardwire touchpad is not communicating to panel. Check installer programming for learned wireless touchpads. The installer code is being used to disarm the system. The system is designed not to disarm using the installer code. Use a regular or system master code to disarm the system. Bypassing Touchpad indicates Invalid and/or “Invalid” is heard when you attempt to bypass a sensor. 1. 2. Attempting to bypass a 24-hour sensor that cannot be bypassed (group 26 fire sensors). Sensor is not active in the current arming level. System cancels sensor bypass when you try to arm to level 2 or 3. Sensor is being bypassed before arming to 2—STAY or 3—AWAY. Arm to the desired level before bypassing a sensor. Wireless Sensor and Touchpad Batteries System indicates Sensor/Touchpad nn low battery. Replace the indicated device battery. Test the sensor/touchpad after replacing the battery. Note If the sensor/touchpad is not tested after battery replacement, the system continues to show a low battery condition, since that was the last signal it received from the device. Testing the sensor/touchpad with new batteries allows the panel to receive a signal with good battery information. Central Station/Pager Reporting Central station/pager is not receiving reports. 1. 2. 3. 4. 5. 6. 7. 8. Check that the premises phone line is working. Perform a phone test. Check that the DB-8 cord is plugged into the RJ-31X/CA-38A jack. Check that the DB-8 cord is wired correctly to the panel. Check for correct phone line wiring between the TELCO block and RJ-31X/CA-38A jack. Replace faulty RJ-31X/CA-38A jack. Replace faulty DB-8 cord. Verify that central station/pager phone number is programmed into the panel. Reprogram the phone number and retest, if necessary. 9. Verify that the correct phone format (SIA or CID) is being used. 10. For pagers, extend the pager delay setting (see the PHONE OPTIONS—GLOBAL menu in the “Programming” section. Alphanumeric Touchpads Display shows all ************. Touchpad is not connected to panel bus terminals or is wired incorrectly. Check and correct wiring. Display is blank. 77 Concord Feature Problem Action/Solution 1. 2. 3. Check that panel is powered up. Check for touchpad power and/or bus miswiring, opens, or shorts. Check touchpad brightness setting (see the user-programming OPTIONS menu in the “Programming” section). Touchpad buttons don’t beep when pressed. 1. 2. Check for touchpad power and/or bus miswiring, opens, or shorts. Check that key beeps option is set to on (see the ACCESSORY MODULES—BUS DEVICES menu in the “Programming” section). Fixed Display Touchpads Display is lit but does not respond to key presses. 1. 2. Touchpad is not connected to panel bus terminals or is wired incorrectly. Check and correct wiring. Check that touchpad is learned into panel memory. Display is blank. 1. 2. 3. Check that panel is powered up. Check for touchpad power and/or bus miswiring, opens, or shorts. Check touchpad brightness setting (see the user-programming OPTIONS menu in the “Programming” section). Touchpad buttons don’t beep when pressed. 1. 2. Check for touchpad power and/or bus miswiring, opens, or shorts. Check that key beeps option is set to on (see the ACCESSORY MODULES—BUS DEVICES menu in the “Programming” section). Speakers Speakers don’t sound alarms. 1. 2. 3. Check for correct wiring at speaker and panel terminals; correct where necessary. Speaker output has shut down because panel detected terminal 7 or 8 is shorted to ground. Disconnect panel AC and battery backup power. Locate short and correct. Apply panel AC and backup battery power and retest. Alarm is in partition 2-6 and speaker is connected to panel terminals 7 and 8, which activate only for partition 1 alarms. Sirens Piezo sirens connected to SnapCard, or onboard (panel) outputs 1 and/or 2 don’t produce any alarm sounds. 1. 2. 3. Check for incorrect wiring between siren and panel; correct where necessary. Output has not been configured (set up) to activate sirens. Enter program mode and configure output (see ACCESSORY MODULES—BUS DEVICES—SNAP CARD, or ONBOARD OPTIONS— OUTPUT 1, 2 in the “Programming” section). Check for correct output partition assignment. Hardwire Zones System doesn’t go into alarm when zone is tripped. 1. 2. 3. 4. System is disarmed. Arm system and then trip the zone. Zone is not learned into panel memory. Enter installer/dealer program mode—LEARN SENSORS, and learn zone into memory. Zone is learned into wrong partition. Delete zone and learn into correct partition or change the partition in the EDIT SENSORS menu. For HIM zones, check that the HIM LED is blinking to verify communication with the panel. If LED is off, check wiring between HIM and panel. Zone reports trouble condition. 1. 2. 3. Check that onboard, HIM, and SnapCard zone inputs have a 2k-ohm EOL resistor installed at the last device on the loop in series for N/C loops, in parallel for N/O loops. Check for zone wire fault—short circuit on N/C loops, open circuit on N/O loops. Make sure all devices on zone are in non-alarm state, then enter disarm command to reset zone. Wireless Sensor Zones System doesn’t respond (in sensor test or when armed) when sensor is tripped. Concord 78 Feature Problem Action/Solution 1. 2. 3. 4. 5. 6. Verify that receiver antennas are installed and connections are secure. Check that the wireless sensor battery(s) are installed. Check the sensor battery(s) for low voltage. Replace battery(s) if necessary. Use an RF Sniffer (60-401) to verify that sensor is transmitting. Sensor is not learned into panel memory. Enter installer/dealer program mode—LEARN SENSORS, and learn sensor into memory. Zone is learned into wrong partition. Delete zone and learn into correct partition or change the partition in the EDIT SENSORS menu. Sensor reports trouble condition. 1. 2. Sensor tamper switch is tripped—sensor cover is off, not latched securely, or sensor is not mounted securely. Secure sensor mounting and/or cover, then trip sensor to clear the condition. Check the sensor battery for low voltage. Replace batteries, if necessary. Touchpad indicates [sensor #] supervisory and/or Sensor [sensor #] supervisory is heard. 1. 2. 3. Use an RF Sniffer (60-401) to verify that sensor is transmitting. If sensor is not transmitting, check battery for low or no voltage and replace. Change mounting position of sensor (from horizontal to vertical or vice versa) and test sensor several times for consistency. Sensor signal is not reaching panel/receiver because sensor is too far away. Remove sensor from mounted location and test from other locations. Mount sensor in area where signal can reach panel/receiver or install a SuperBus 2000 RF Transceiver in the vicinity of the sensor. Smoke sensor beeps once every 44 seconds. Sensor batteries are getting low. Replace batteries. Wireless Touchpads System doesn’t respond to commands entered from wireless touchpad. 1. 2. 3. 4. 5. 6. Verify that receiver antennas are installed and connections are secure. Check that touchpad battery(s) are properly installed. Check the touchpad battery(s) for low voltage. Replace battery(s), if necessary. Use an RF Sniffer (60-401) to verify that touchpad is transmitting. Touchpad is not learned into panel memory. Enter program mode and learn touchpad into memory (see LEARN SENSORS). Touchpad is learned into wrong partition. Delete touchpad and learn into correct partition or change the partition in the EDIT SENSORS menu. Touchpad reports trouble condition. Check the touchpad battery(s) for low voltage. Replace battery(s), if necessary. Phones Loss of dial tone at on-site phones after wiring RJ-31X jack or connecting the DB-8 cord. 1. 2. 3. 4. 5. Wait 2 minutes and try again. The panel may be busy trying to report to the central station. Disconnect the panel DB-8 cord from the RJ-31X jack. If the phone still doesn’t work, the system is okay and the problem is in the wiring. Check RJ-31X jack wiring and TELCO block wiring. Replace RJ-31X jack if necessary. Check DB-8 cord connections at the panel and RJ-31X jack. Replace cord if necessary. Perform a phone test after troubleshooting the phone line. Constant dial tone, preventing dial-out on premises phones. One or more polarity-sensitive phones exist on-site. Reverse the phone wires connected to the brown and gray wire terminals on the RJ-31X jack. Light Control Light controlled by X10 Lamp Module is not working. 79 Concord Feature Problem Action/Solution 1. 2. 3. 4. 5. 6. 7. Check that the lamp has a working bulb and that the lamp switch is on. Check to make sure X10 module is not plugged into an outlet controlled by a switch. Move to a nonswitched outlet location and test. Panel is not powered by a power line carrier transformer. Replace existing transformer with a power line carrier transformer. Power transformer and X10 modules are not plugged into outlets on the same electrical phase. Relocate modules or transformer to different outlets to determine working locations. Check that the HOUSE dial on the X10 module matches the partition house code programmed into the panel. X10 module is located in wrong partition. Move module to correct partition and retest. Partition house codes are not programmed into panel. Enter program mode and set partition house codes. Energy Saver Module Module does not respond to system commands or appear to control furnace. 1. 2. 3. Check that the module is wired correctly to the panel terminals. Verify the module LED is flashing continuously. If the LED is not flashing, remove power and check wiring. There is a 5-minute delay after the module returns control to the furnace/AC thermostat, before the module overrides the thermostat again. Wait 5-minutes and try again. Module temperature does not match actual room temperature. The module room temperature setting has not been adjusted or was adjusted before the module warmed or cooled to room temperature. To ensure accuracy, wait at least 15 minutes after installing the module before adjusting the temperature. To adjust the module room temperature setting, see TEMPERATURE under the ACCESSORY MODULES—BUS DEVICES—UNIT-ID—ENERGY OPTIONS menu in the section “Programming the Panel.” Automation Module Module is not controlling or communicating with the panel and panel indicates a “BUS FAILURE UNIT nn” where nn is the Automation Module bus unit number. 1. 2. Check that the module is wired correctly to the panel terminals. Verify the SuperBus Module’s red LED is flashing continuously. If the LED is not flashing, remove power and check wiring. Module is not controlling or communicating with the panel and panel indicates a “BUS FAILURE UNIT AMnn” where nn is the Automation Module bus unit number. 1. 2. Check that the RS-232 cable is firmly connected to the Automation Module and the Automation Device. Verify the Automation Device is powered and turned on. Module is not controlling or communicating with the panel and panel does not indicate a bus failure. Verify the Automation Module is learned into panel memory. Cellular Backup Module Cellular backup report does not occur. 1. 2. 3. Verify the Cellular Backup option is on for the CS phone number being tested. Verify that the module is learned into panel memory. Check that the Cellular Backup Module has been activated as outlined in the device Installation Instructions. The panel indicates “auxiliary phone trouble 1.” 1. 2. 3. 4. Check the antenna connection. Adjust the antenna positioning for maximum signal. Verify Cellular System setting. Check that the Cellular Backup Module has been activated as outlined in the device Installation Instructions. The panel indicates “auxiliary phone trouble 2.” 1. 2. 3. Check the antenna connection. Adjust the antenna positioning for maximum signal. Verify Cellular System setting. The panel indicates “auxiliary phone trouble 3.” Concord 80 Feature Problem Action/Solution 1. 2. Check the antenna connection. Adjust the antenna positioning for maximum signal. The panel indicates “auxiliary phone trouble 4.” Contact the cellular provider for details. The panel indicates “auxiliary phone trouble 5.” Contact the cellular provider for details. The panel indicates “auxiliary phone trouble 6.” Replace the module. SuperBus 2000 Wireless Gateway Module Module is not communicating on Bus and indicates a “Bus Failure Unit nn”. Where nn represents the Wireless Gateway unit number. 1. 2. Check that the module is wired correctly to the panel terminals. Verify that the module’s red Bus LED is flashing. If not, remove power and check all the wiring. Module’s status LED’s don’t turn on after initial power-up. 1. 2. Wait 5 - 8 minutes for the module to communicate with alarm.com. Access code Lock feature must be turned off to work properly. Module doesn’t communicate with alarm.com. 1. 81 Check module’s status LED’s. Refer to the “SuperBus 2000 Wireless Gateway Module” instructions for a description of the LED’s. Concord Appendix A: System Planning Worksheets Customer Name _________________________________ Address _______________________________________ City _________________ County ___________ State ___ Zip __________ Phone (____) ___________ Table A1: Wireless Devices Part No. Concord Description 60-362 Door/Window Sensor 60-670 SAW Door/Window Sensor 60-741-95 Micro Recessed Door/Window Sensor 60-499 Slim Line Door/Window Sensor 60-688 Micro Door/Window Sensor 60-641 Long-Life Door/Window Sensor 60-461* Shock Sensor 60-459* Sound Sensor 60-462* Glass Guard Sensor 60-506 System Sensor Smoke Sensor 60-838-95R 2100ARFT Smoke Sensor 60-848-01-95 ESL 562 Smoke Sensor 60-460 Rate-of-Rise Heat Sensor 60-589* Manual Fire Pull Sensor 60-504* Freeze Sensor 60-452 Pendant Panic Sensor 60-458 Single Button Panic Sensor 60-457 Dual Button Panic Sensor 60-578 Water-Resistant Panic Sensor 60-511-01-95 DS924i PIR Motion Sensor 60-639-95R SAW Indoor PIR Motion Sensor 60-639-95R-OD SAW Outdoor PIR Motion Sensor (Not for intrusion protection) 60-703-95 Crystal Indoor PIR Motion Sensor 60-834-95 Adjustable Dual technology Sound Sensor 60-597 HiTech Handheld Wireless Touchpad 60-607 2-Button Keychain Touchpad 60-606 4-Button Keychain Touchpad 60-659-95R SAW 4-Button Keychain Touchpad 60-832-95R 2-Button ELM Keychain Touchpad 600-XXXX-95 Dialog RF Iconized LCD Touchpad 60-909-95 Dialog RF Thermostat 60-XXX-95 Dialog RF Siren Qty. 82 Table A2: Hardwire Devices Part No. Description Qty. mA (Max.) Sub Total Hardwire Sensors/Detectors N/A System Sensor models 2100D, 2100TD, 2100S, 2100TS, 2400, or 2400TH or ESL series 429AT, 521B or 521BXT 10 mA 13-082 PIR Motion Detector 10 mA Sirens 13-046 Hardwire Exterior Siren 145 mA 13-949 Hardwire Interior Siren 85 mA 13-950 Piezo Dynamic Exterior Siren 150 mA SuperBus 2000/Miscellaneous Components 60-746-01 2x16 LCD Alphanumeric Touchpad 90 mA 60-820 Fixed Display LCD Touchpad 30 mA 60-803 2x20 LCD Alphanumeric Touchpad 120 mA 60-804 2x20 VFD Alphanumeric Touchpad 120 mA 60-983 ATP 1000 110 mA 60-984 ATP 2600 165 mA 60-985 ATP 2100 165 mA 600-1013 GTS 50 300 mA 60-777-01 Phone Interface/Voice Module 600 mA 600-1025-95R RF Transceiver 55 mA 600-1019 2 Amp Power Supply N/A 60-756 4 Input/2 Output SnapCard 185 mA 60-757 8Z Hardwire Zone Expander SnapCard 230 mA 60-758 4 Output SnapCard 130 mA 60-774 Hardwire Input Module 18 mA 60-770 Hardwire Output Module 91 mA 60-620-01 Energy Saver Module 20 mA 60-677* Interrogator 200 Audio Verification Module 10 mA 60-783-02* Automation Module 35 mA Total power consumption: mA Total power consumption not to exceed: 1,000 mA * These devices not listed, investigated, or verified by UL. † Listed, but not tested for compatibility by UL. 83 Concord Table A3: Zone and Sensor Assignments No. RF Zone Module Bus ID Number Module Input Number Group Partition Zone/Sensor Text 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 Concord 84 Table A3: Zone and Sensor Assignments (Continued) No. RF Zone Module Bus ID Number Module Input Number Group Partition Zone/Sensor Text 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 85 Concord Table A3: Zone and Sensor Assignments (Continued) No. RF Zone Module Bus ID Number Module Input Number Group Partition Zone/Sensor Text 89 90 91 92 93 94 95 96 Table A4: System Settings Index and Record Setting (reference) default Shortcut No. Setting Installer Programming—8 + Installer/Dealer CODE + 00 24 Hour Tamper Off 06000 AC Failure Off 06010 Access Code Lock (On) 0003 Access Timeout 90 sec 0904 Account No. 00000 0010-0060 Activity Timeout 24 hrs 0305 Alarm Verify Off 06108-06608 Antenna Tamper Off 06001 Audio Mode 1 0901 Audio Verify Off 0900 Auto Phone Test Off 02001 Auto Stay Arming On 0014-0064 Auto Test Reset On 02002 Auxiliary Panic On 0511-0561 Aux Power Fail Off AVM Access Code None 0906 Back In Service On 06002 Backup CS Phone 1 On, CS Phone 2-3 Off 0105, 0115, 0125 Battery Restoral Off 06005 Beep Delay 2 sec 0905 Buffer Control Off 06001 Buffer Full Report Off 06006 1_____________2_____________3___________ Bypass Reports Off 06003 Call Wait Cancel None 02009 Cancel Message On 02007 Cellular Backup CS Phone 1 On, CS Phone 2-3 Off 0107, 0117, 0127 1_____________2_____________3___________ Closing Reports Off 06101, 06201 1_____________2_____________ Comm. Failure On 02003 CS Phone 1-3 None 0100, 0110, 0120 Cellular System B Daylight Saving On 0306 Dealer Code None 0002 Concord 1_____________2_____________3___________ 86 Table A4: System Settings Index and Record (Continued) Setting (reference) default Shortcut No. Delete Sensors None 082 Dial Tone Detect On 02010 Dialer Abort On 02005 Dial Abort Delay 30 sec 02006 Disable Trouble Beeps Off 0701 Downloader Code 12345 0000 Downloader Phone No. None 0180 DTMF Dialing On 02004 Setting Duress Code None 0017-0067 Duress Option Off 06104-06604 Edit Sensors None 083 Entry Delay 30 sec 0310-0360 Entry Lights none 0400-0450 Exception Reports (phones) Off 0103, 0113, 0123 Exception Reports (pagers) Off 0133, 0143, 0153, 1_____________2_____________3___________ 0163, 0173 4_____________5_____________ Exit Delay 60 sec 0311-0361 Exit Extension On 0013-0063 Extended Delay 4 min 0312-0362 Fire Panic On 0510-0560 Fire Shutdown Off 0902 Force Armed Off 06105-06605 1_____________2_____________3___________ Freeze Alarm Off 06107-06607 Freeze Temp 42 06108-06608 Global Fire Off 0704 High Level Reports (phones) CS Phone 1 On, CS Phone 2-3 Off 0101, 0111, 0121 High Level Reports (pagers) On 0131, 0141, 0151, 1_____________2_____________3___________ 0161, 0171 4_____________5_____________ House Code 1B, 2C, 3D, 4E, 5F, 6G 0401-0451 Immediate Beeps Off 0700 Installer Code 4321 0001 Keychain TP Arming Off 0513-0563 Keychain TP PTN 0006 Keyswitch Sensor None 0015-0065 1_____________2_____________3___________ Keyswitch Style Transition 0016-0066 Latchkey Format Off 06106-06606 Latchkey Reports (pagers) On 0135, 0145, 0155, 1_____________2_____________3___________ 0165, 0175 4_____________5_____________ Latchkey Zones None 0500 Learn Sensors None 080 Line Fail Delay None 0213 Local Phone Control On 0210-0260 Low CPU Battery On 06004 Low Level Reports (phones) CS Phone 1 On, CS Phone 0102, 0112, 0122 2-3 Off 87 1_____________2_____________3___________ Concord Table A4: System Settings Index and Record (Continued) Setting (reference) default Shortcut No. Setting Low Level Reports (pagers) Off 0132, 0142, 0152, 1_____________2_____________3___________ 0162, 0172 4_____________5____________ Multi-PTN Arm Off 0005 Next Phone Test 7 days 0303 No Activity Off 06103, 06203 1_____________2____________ Open/Close Reports (phones) Off 0104, 0114, 0124 1_____________2_____________3___________ Open/Close Reports (pagers) Off 0134, 0144, 0154, 1_____________2_____________3___________ 0164, 0174 4_____________5_____________ Opening Reports Off 06100-06600 Onboard Output 1 01614- any audible alarm 11101 Onboard Output 2 01710 - status & alarm tones 11111 Output Trip Time 4 sec 0304 Pager Delay 15 sec 02008 Pager Partition Assignment 1 0137, 0147, 0157, 1_____________2_____________3___________ 0167, 0177 4_____________5_____________ Pager Phone 1-5 None 0130, 0140, 0150, 1_____________2_____________3___________ 0160, 0170 4_____________5_____________ Partition Security On 0004 Phone Access Key # 0216-0266 Phone Panic Off 0215-0265 Phone Test On 02000 Phone Test Freq. 7 days 0302 Police Panic On 0512-0562 Program Report Off 06015 Quick Arm Off 0011-0061 Quick Exit On 0012-0062 Receiver Failure Off 06011 Recent Closings On 06102-06602 Remote Access On 0211-0221 RF Low Battery Rpt Weekly 06012 RF Supervisory Rpt Weekly 06013 RF TX Timeout 12 hrs 0301 Ring/Hang/Ring On 0212-0262 Reporting Format (SIA/CID) CID 0106, 0116, 0126 Sensor Text None 081 SIA False Alarm Reduction 0004 Silent Talkback Off 0903 Siren Timeout 4 min 0313-0363 Siren Verify Off 0710 Sleep Time Off 0314-0364 Smoke Verify Off 1100 SnapCard Output 1 (01400 - keychain touchpad star button activation) 101001 SnapCard Output 2 (00410 - any audible alarm) 101011 1_____________2_____________3___________ SnapCard Output 3 (00903 - arming to STAY or AWAY) 101021 SnapCard Output 4 (01003 - arming to AWAY) 101031 Star Is No Delay Off 0514-0564 Concord 88 Table A4: System Settings Index and Record (Continued) Setting (reference) default Streamlining On Shortcut No. 0136, 0146, 0156, 1_____________2_____________3___________ 0166, 0176 4_____________5_____________ Supervisory Time 03:00 0300 Swinger Limit 1 06014 SWS Code 003 0703 System Tamper Off 06109-06609 Toll Saver On 0214-0264 TP Panic RPT FMT Off 06009 Two Trip Error Off 06008 Two Wire Smoke Off 1101 UL 98 Options Off 0702 Zone Restorals Off 06007 89 Setting Concord Appendix B: Reference Tables CS Report √ √ √ √ √ 1, 2, 3 √ √ 1, 2, 3 √ √ 1, 2, 3 Auxiliary Instant √ 1, 2, 3 Portable Auxiliary 24-hour portable auxiliary button. Siren shutoff confirms CS report. Auxiliary Instant √ 1, 2, 3 08 Special Intrusion Special belongings, such as gun cabinets and wall safes. Police 09 Special Intrusion Special belongings (i.e. gun cabinets and wall safes.) Police No. Name Application Alarm Delay 00 Fixed Panic 24-hour audible fixed emergency buttons. Police Instant 01 Portable Panic 24-hour audible portable emergency buttons. Police Instant 02 Fixed Panic 24-hour silent fixed emergency buttons. Silent Instant 03 Portable Panic 24-hour silent portable emergency buttons. Silent Instant 04 Fixed Auxiliary 24-hour auxiliary sensor, such as Pendant Panic or holdup button. Auxiliary Instant 05 Fixed Auxiliary 24-hour auxiliary emergency button. Siren shutoff confirms CS report. Auxiliary Instant 06 Portable Auxiliary 24-hour portable auxiliary alert button. 07 Restoral Supervisory Active Levels Chime (Level 1) Table B1: Sensor Group Characteristics √ 1, 2, 3 1, 2, 3 1, 2, 3 Instant √ √ √ 1, 2, 3 Standard √ √ √ 1, 2, 3 10 Entry/Exit Delay Entry and exit doors that require a standard delay time. Police Standard √ √ √ √ 2, 3 11 Entry/Exit Delay Garage doors and entrances that require an extended Police delay time. * Extended √ √ √ √ 2, 3 12 Entry/Exit Delay Driveway gates and entrances that require a twice extended delay time. * Police Twice Extended √ √ √ √ 2, 3 13 Instant Perimeter Exterior doors and windows. Police Instant Instant Interior Interior doors. Police Follower 15 Instant Interior Interior PIR motion sensors. * Police Follower 16 Instant Interior Interior doors. Police Follower 17 Instant Interior PIR motion sensors. * Police Follower 18 Instant Interior Instant Interior Cross-Zone# PIR motion sensors. * † Police Follower √ √ √ √ √ √ √ √ √ √ √ √ √ 2, 3 14 √ √ 19 Delayed Interior Interior doors that initiate a delay before going into alarm. * Police Standard √ √ 3 20 Delayed Interior PIR motion sensors that initiate a delay before going into alarm. * Police Standard √ √ 3 21 Local Instant Interior 24-hour local alarm zone protecting anything that opens and closes. Police Instant √ √ 1, 2, 3 22 Local Delayed Interior Same as group 21, plus activation initiates a delay before going into alarm. Police Standard √ √ 1, 2, 3 23 Local Instant Auxiliary 24-hour local alarm zone protecting anything that opens and closes. ‡ Auxiliary Instant √ √ 1, 2, 3 24 Local Instant Auxiliary 24-hour local alarm zone protecting anything that opens and closes. Sirens shut off at restoral. * Auxiliary Instant √ √ 1, 2, 3 25 Local Special Chime Notify the user when a door is opened. Sounds emit from a local annunciator. * Special Chime Instant √ 1, 2, 3 26 Fire 24-hour fire, rate-of-rise heat, and smoke sensors. Fire Instant Concord √ √ √ √ √ 2, 3 2, 3 3 3 3 1, 2, 3 90 Delay 27 Output Module Hardwire Output Module (HOM) lamp control or other Silent customer feature. ‡ Instant 28 Output Module HOM, PIR motion sensor, sound sensor or pressure mat. ‡ Silent Instant 29 Auxiliary Freeze sensor. Auxiliary Instant 32 Output Module HOM, PIR motion sensor, sound sensor or pressure mat.‡ Silent Instant 33 Siren Wireless Siren Supervision. ‡ Silent Instant 34 Gas Carbon monoxide (CO) Gas Detectors ‡ Auxiliary Instant 35 Local Instant Police (Day Zone) Local alarm in levels 1 and 2. Report to CS in level 3. Police 38 Auxiliary Water sensor ‡ Active Levels Alarm √ √ 1, 2, 3 √ 1, 2, 3 CS Report Application Supervisory Name Restoral No. Chime (Level 1) Table B1: Sensor Group Characteristics (Continued) √ √ √ 1, 2, 3 √ √ 1, 2, 3 √ √ √ Instant √ √ Auxiliary Instant √ √ √ (level 3 only) √ 1, 2, 3 1, 2, 3 1, 2, 3 Note: Check marks (√) represent characteristics present in a group. * This group is not certified as a primary protection circuit for UL-listed systems and is for supplementary use only. † Sounds instant police siren if two or more sensors are tripped within 4 minutes. Otherwise sensors are followers to delayed sensors. If Alarm Verification is on, group 18 functions like group 17. ‡ This group has not been investigated by UL. § This group is required for UL-listed residential fire alarm applications. Cross-Zoning Note Cross-Zoning is not recommended for exit/entry zones. Each zone has the ability to individually protect the intended area. (e.g. motion detector patterns overlap). Cross-Zone (Alarm Verify) refers to two different Group 10-20 sensors that must be tripped within four minutes of each other to report an alarm to the central station. The diagram in the figure below shows the path of a person walking from the kitchen to the living room. When the person is detected walking through the kitchen, the motion sensor in the kitchen is tripped, sounding a local alarm. If motion is detected by the living room motion sensor within four minutes, an alarm report will be sent to the central station. D in in g R o o m K itc h e n B e d ro o m L iv in g R o o m B e d ro o m H a ll B e d ro o m D e te c tio n P a th /K itc h e n M o tio n S e n s o r D e te c tio n P a th /L iv in g R o o m M o tio n S e n s o r M o tio n S e n s o r P a th o f P e r s o n W a lk in g 91 Concord Table B2: Item Numbers and Sensor Text Sensor Text Item # 001 002 003 004 005 006 007 008 009 010 011 012 013 014 015 016 017 018 019 020 021 022 023 024 025 026 027 028 029 030 031 032 033 034 035 036 037 038 039 040 Aborted AC Access Active Activity Alarm All AM Area Arm Armed Arming Attic Auxiliary Away Baby Back Bar Basement Bathroom Battery Bedroom Bottom Breezeway Building Bus Bypass Bypassed Cabinet Canceled Car Carbon Monoxide Central Chime Closed Closet Closing Code Computer Control Concord Item # Sensor Text Item # Sensor Text Item # Sensor Text Item # Sensor Text 041 042 043 044 045 046 047 048 049 050 051 052 053 054 055 056 057 058 059 060 061 062 063 064 065 066 067 068 069 070 071 Date Daughter’s Degrees Delay Den Desk Detector Dining Disarmed Door Down Download Downstairs Drawer Driveway Duct Duress East Energy Saver Enter Entry Error Exit Exterior Factory Failure Family Father’s Feature Fence Fire 081 082 083 084 085 086 087 088 089 090 091 092 093 094 095 096 097 098 099 100 101 102 103 104 105 106 107 108 109 110 111 Gas Glass Goodbye Hallway Heat Hello Help High Home House In Install Interior Intrusion Invalid Is Key Kids Kitchen Latchkey Laundry Left Level Library Light Lights Living Load Loading Low Lower 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 North Not Now Number Off Office OK On Open Opening Panic Partition Patio Pet Phone Please PM Police Pool Porch Power Press Program Progress Quiet Rear Receiver Report RF Right Room 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 Siren Sliding Smoke Son’s Sound South Special Stairs Stay Supervisory System Tamper Temperature Test Time To Touchpad Trouble Unbypass Unit Up West Window Zone 0 1 2 3 4 5 6 072 First 112 Main 152 Safe 192 7 073 074 075 076 077 078 079 080 Floor Force Foyer Freeze Front Furnace Gallery Garage 113 114 115 116 117 118 119 120 Master Mat Medical Memory Menu Mother’s Motion No 153 154 155 156 157 158 159 160 Schedule Screen Second Sensor Service Shed Shock Side 193 194 195 196 197 198 199 200 8 9 A B C D E F Item # 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 Sensor Text G H I J K L M N O P Q R S T U V W X Y Z (space) ’(apostrophe) - (dash) _ (underscore) * # : / ? 92 Table B3: System Event Trigger Numbers System Event Null Trigger (used for direct control) Description Activated only by schedule or direct command. Trigger No. 000 Fire Alarm When Fire sirens are started. 001 Police Alarm When Police sirens are started. 002 Auxiliary Alarm When Auxiliary sirens are started. 003 Any Audible Alarm When any of the above sirens are started. 004 Silent Alarm (sensor groups 2, 3, and duress) When a group 2 or 3 sensor goes into alarm or when a duress 005 alarm is activated (does not include groups 25, 27, 28, or 32). Any Audible or Silent Alarm When any alarm is started (does not include groups 25, 27, 28, 006 or 32). HOM Group 27, 28, 32 in Alarm When a sensor in group 27, 28, or 32 goes into alarm. Major Trouble (phone or receiver failure) When a receiver failure (S94) or a phone failure (S96) occurs. 008 007 Arming to STAY or AWAY When the system is armed to level 2 or 3. 009 Arming to AWAY When the system is armed to level 3. 010 AVM is Interactive (audio session in progress) When the central station operator begins listening or talking to 011 the premises. Fail-to-Communicate (panel can’t call CS or pager) When the fail-to-communicate output is activated. 012 AVM Trip (edge) When an AVM alarm occurs, output is activated momentarily. 013 Keychain Touchpad Star Button-Press When the star button on a keychain touchpad is pressed. 014 Smoke Power (for resetting 4-wire smoke detectors) Deactivated when hardwire smoke detectors need to be reset. 015 Exterior Siren Activated for police or fire alarms. 016 Interior Siren Activation follows all system noises 017 AVM Trip (pulse) When an AVM alarm occurs, output is deactivated for 10 ms 018 State of System Status Follows the state of system status (ready or trouble). 019 Tamper Condition When any tamper is tripped 020 Closing Report Sent When a closing report has been successfully transmitted to the 021 central station. Arming to Level 1 When the system is disarmed. 022 Group XX in Alarm When any sensor in group XX goes into alarm Table B4 Sensor XX in Alarm When sensor number XX goes into alarm Table B5 Sensor XX Open When sensor number XX is opened Table B5 93 Concord Table B4: Sensor Group Event Trigger Numbers Sensor Group Trigger No. Sensor Group Trigger No. Group 00 in alarm 064 Group 17 in alarm 081 Group 01 in alarm 065 Group 18 in alarm 082 Group 02 in alarm 066 Group 19 in alarm 083 Group 03 in alarm 067 Group 20 in alarm 084 Group 04 in alarm 068 Group 21 in alarm 085 Group 05 in alarm 069 Group 22 in alarm 086 Group 06 in alarm 070 Group 23 in alarm 087 Group 07 in alarm 071 Group 24 in alarm 088 Group 08 in alarm 072 Group 25 in alarm 089 Group 09 in alarm 073 Group 26 in alarm 090 Group 10 in alarm 074 Group 27 in alarm 091 Group 11 in alarm 075 Group 28 in alarm 092 Group 12 in alarm 076 Group 29 in alarm 093 Group 13 in alarm 077 Group 32 in alarm 096 Group 14 in alarm 078 Group 33 in alarm 097 Group 15 in alarm 079 Group 34 in alarm 098 Group 16 in alarm 080 Group 35 in alarm 099 Table B5: Sensor Number Event Trigger Numbers Sensor Number Concord State Trigger No. State Trigger No. Sensor 01 in alarm 129 open 257 Sensor 02 in alarm 130 open 258 Sensor 03 in alarm 131 open 259 Sensor 04 in alarm 132 open 260 Sensor 05 in alarm 133 open 261 Sensor 06 in alarm 134 open 262 Sensor 07 in alarm 135 open 263 Sensor 08 in alarm 136 open 264 Sensor 09 in alarm 137 open 265 Sensor 10 in alarm 138 open 266 Sensor 11 in alarm 139 open 267 Sensor 12 in alarm 140 open 268 Sensor 13 in alarm 141 open 269 Sensor 14 in alarm 142 open 270 Sensor 15 in alarm 143 open 271 Sensor 16 in alarm 144 open 272 Sensor 17 in alarm 145 open 273 Sensor 18 in alarm 146 open 274 Sensor 19 in alarm 147 open 275 Sensor 20 in alarm 148 open 276 94 Table B5: Sensor Number Event Trigger Numbers Sensor Number 95 State Trigger No. State Trigger No. Sensor 21 in alarm 149 open 277 Sensor 22 in alarm 150 open 278 Sensor 23 in alarm 151 open 279 Sensor 24 in alarm 152 open 280 Sensor 25 in alarm 153 open 281 Sensor 26 in alarm 154 open 282 Sensor 27 in alarm 155 open 283 Sensor 28 in alarm 156 open 284 Sensor 29 in alarm 157 open 285 Sensor 30 in alarm 158 open 286 Sensor 31 in alarm 159 open 287 Sensor 32 in alarm 160 open 288 Sensor 33 in alarm 161 open 289 Sensor 34 in alarm 162 open 290 Sensor 35 in alarm 163 open 291 Sensor 36 in alarm 164 open 292 Sensor 37 in alarm 165 open 293 Sensor 38 in alarm 166 open 294 Sensor 39 in alarm 167 open 295 Sensor 40 in alarm 168 open 296 Sensor 41 in alarm 169 open 297 Sensor 42 in alarm 170 open 298 Sensor 43 in alarm 171 open 299 Sensor 44 in alarm 172 open 300 Sensor 45 in alarm 173 open 301 Sensor 46 in alarm 174 open 302 Sensor 47 in alarm 175 open 303 Sensor 48 in alarm 176 open 304 Sensor 49 in alarm 177 open 305 Sensor 50 in alarm 178 open 306 Sensor 51 in alarm 179 open 307 Sensor 52 in alarm 180 open 308 Sensor 53 in alarm 181 open 309 Sensor 54 in alarm 182 open 310 Sensor 55 in alarm 183 open 311 Sensor 56 in alarm 184 open 312 Sensor 57 in alarm 185 open 313 Sensor 58 in alarm 186 open 314 Sensor 59 in alarm 187 open 315 Sensor 60 in alarm 188 open 316 Sensor 61 in alarm 189 open 317 Sensor 62 in alarm 190 open 318 Concord Table B5: Sensor Number Event Trigger Numbers Sensor Number Concord State Trigger No. State Trigger No. Sensor 63 in alarm 191 open 319 Sensor 64 in alarm 192 open 320 Sensor 65 in alarm 193 open 321 Sensor 66 in alarm 194 open 322 Sensor 67 in alarm 195 open 323 Sensor 68 in alarm 196 open 324 Sensor 69 in alarm 197 open 325 Sensor 70 in alarm 198 open 326 Sensor 71 in alarm 199 open 327 Sensor 72 in alarm 200 open 328 Sensor 73 in alarm 201 open 329 Sensor 74 in alarm 202 open 330 Sensor 75 in alarm 203 open 331 Sensor 76 in alarm 204 open 332 Sensor 77 in alarm 205 open 333 Sensor 78 in alarm 206 open 334 Sensor 79 in alarm 207 open 335 Sensor 80 in alarm 208 open 336 Sensor 81 in alarm 209 open 337 Sensor 82 in alarm 210 open 338 Sensor 83 in alarm 211 open 339 Sensor 84 in alarm 212 open 340 Sensor 85 in alarm 213 open 341 Sensor 86 in alarm 214 open 342 Sensor 87 in alarm 215 open 343 Sensor 88 in alarm 216 open 344 Sensor 89 in alarm 217 open 345 Sensor 90 in alarm 218 open 346 Sensor 91 in alarm 219 open 347 Sensor 92 in alarm 220 open 348 Sensor 93 in alarm 221 open 349 Sensor 94 in alarm 222 open 350 Sensor 95 in alarm 223 open 351 Sensor 96 in alarm 224 open 352 96 Table B6: System Feature Event Trigger Numbers Feature State Trigger No. Phone Test initiated 225 AC Failure for 15 minutes 226 CPU Low Battery detected (excluding first minute after power-up) 227 Auto Phone Test begun 228 Receiver Failure detected 229 Back In Service alarm (AC loss, battery drain, then AC restore) 230 Phone Failure detected 231 Buffer Full detected 232 Two Trip Error detected 233 System Tamper alarm (40 incorrect code entry keystrokes) 236 Freeze alarm 237 No Activity alarm 238 Fire Panic alarm 239 Police Panic alarm 240 Auxiliary Panic alarm 241 Opening Report occurred 242 Closing Report occurred 243 Latchkey Opening or Closing occurred 244 Duress alarm 245 Force Armed Report occurred 246 Fire in Partition alarm 247 Recent Closing Report occurred 248 Sensor Test entered 249 Table B7: Response Characteristics Response Characteristics Description Momentary trip time The point will remain activated for nn seconds (n is 1-12 seconds). The default is 4 seconds 97 3 minute trip time The point will remain activated for 3 minutes Siren-time trip time The point will remain activated while the interior siren is sounding Sustained trip time The point will remain activated for the duration of the event Siren pattern The point will activate and deactivate according to the current alarm type: Auxiliary -- fast on/off/on Police -- constant on Fire -- repeating) Trip delay The point will activate 30 seconds after the trigger event occurs Concord Table B8: Response Numbers Siren Tracking no Response Time Trip Delay Response No. no momentary 00 no no 3 minutes5 01 no no siren time2 02 no no sustained3 03 no yes4 momentary 04 no yes4 3 minutes5 05 no yes4 siren time2 06 no 4 sustained3 07 no momentary 08 no minutes5 09 no siren time2 10 no sustained3 11 yes1 yes4 momentary 12 yes1 yes4 3 minutes5 13 yes1 yes4 siren time2 14 yes1 yes4 sustained3 15 yes yes 1 yes 1 yes1 yes 1 3 Notes for Table B8: Response Numbers Note The mechanical lifetime of the relay may be exceeded if an output is set up for a siren tracking response and a pulsing siren (auxiliary or fire) is active for long time periods. A SnapCard relay output’s lifetime expectancy is about 350 total pulsing hours. 1. If an event does not trigger sirens, siren tracking response numbers activate without turning on the output. If sirens are triggered by another event, the output pulses to match the siren. If the siren cadence changes (from police to fire, for example), outputs set up for siren tracking change to match the siren and all pulsing outputs pulse to one common cadence. 2. If an event does not trigger sirens, siren time response times activate outputs only if sirens are active for another reason. If an alarm event does not necessarily require disarming (no activity, closing report, etc.), outputs set up for a sustained response time remain activated until the next arming level change. If an event occurs that activates an output set up for trip delay, the delay and output activation can be canceled by trigger event restoral. Activated outputs set up for a 3-minute response time remain active for the entire three minutes. To deactivate the output before the 3-minute time expires, you must enter program mode or remove panel power. Activated outputs set up for a momentary or 3-minute response time restart if the same trigger event occurs again. 3. 4. Note The trip delay is factory set for 30 seconds and cannot be changed. Concord 5. 98 99 Concord Appendix C: Settings Tier 1 Menus #` 6<67(0 352*5$00,1* _· BdcA Demo Kit On Off Tier 2 Menus #dc · GLOBAL · BdcA #dc Partition 1 Copy Downloader Code 12345 (0000) BdcA Clear Memory BdcA Exit Programming # BdcA Installer Code 4321 (0001) BdcA Dealer Code **** (0002) BdcA Access Code Lock On Off (0003) BdcA Ptn Security On Off (0004) BdcA Multi Ptn Arm On Off (0005) BdcA Keychain TP Ptn (0006) BdcA SIA False Alarm On Off (0007) Concord B` _A 6(&85,7< #dc B` _A PARTITION #dc · Account Number 00000 (0010 - 0060) BdcA Quick Arm On Off (0011 - 0061) BdcA Quick Exit On Off (0012 - 0062) BdcA Exit Extension On Off (0013 - 0063) BdcA Auto Stay Arming On Off (0014 - 0064) BdcA Keyswitch Sensor On Off (0015 - 0065) BdcA Keyswitch Style Transition State (0016 - 0066) BdcA Duress Code **** (0017 - 0067) B` _A 3+21(6 · CS PHONE 1 #dc · B` _A CS PHONE 2 · B` _A CS PHONE 3 · #dc #dc Phone Number None (01000) Phone Number None (01010) Phone Number None (01020) BdcA BdcA High Lvl Rpts On Off (01001) High Lvl Rpts On Off (01011) High Lvl Rpts On Off (01021) BdcA BdcA BdcA BdcA Low Lvl Rpts On Off (01002) Low Lvl Rpts On Off (01012) Low Lvl Rpts On Off (01022) BdcA Exception Rpts On Off (01003) BdcA Open/Close Rpts On Off (01004) BdcA Backup On Off (01005) BdcA Reporting Format SIA CID (01006) BdcA Cellular Backup On Off (01007) BdcA Exception Rpts On Off (01013) BdcA Open/Close Rpts On Off (01014) BdcA Backup On Off (01015) BdcA Reporting Format SIA CID (01016) BdcA Cellular Backup On Off (01017) BdcA Exception Rpts On Off (01023) BdcA Open/Close Rpts On Off (01024) BdcA Backup On Off (01025) BdcA Reporting Format SIA CID (01026) BdcA Cellular Backup On Off (01027) 100 B` _A 3+21(6 FRQW #dc · PAGER 1 #dc · B` _A PAGER 2 #dc · B` _A PAGER 3 #dc · Phone Number None (01030) Phone Number None (01040) BdcA BdcA High Lvl Rpts On Off (01031) High Lvl Rpts On Off (01041) High Lvl Rpts On Off (01051) BdcA Phone Number None (01050) B` _A PAGER 4 #dc · B` _A PAGER 5 · #dc Phone Number None 01090 High Lvl Rpts On Off (01061) High Lvl Rpts On Off (01071) BdcA BdcA BdcA BdcA BdcA BdcA Low Lvl Rpts On Off (01042) Low Lvl Rpts On Off (01052) Low Lvl Rpts On Off (01062) Low Lvl Rpts On Off (01072) BdcA Open/Close Rpts On Off (01034) BdcA Latchkey Rpts On Off (01035) BdcA Exception Rpts On Off (01043) BdcA Open/Close Rpts On Off (01044) BdcA Latchkey Rpts On Off (01045) BdcA Exception Rpts On Off (01053) BdcA Open/Close Rpts On Off (01054) BdcA Latchkey Rpts On Off (01055) BdcA Exception Rpts On Off (01063) BdcA Open/Close Rpts On Off (01064) BdcA Latchkey Rpts On Off (01065) BdcA Exception Rpts On Off (01073) BdcA Open/Close Rpts On Off (01074) BdcA Latchkey Rpts On Off (01075) BdcA BdcA BdcA BdcA BdcA Streamlining On Off (01036) Streamlining On Off (01046) Streamlining On Off (01056) Streamlining On Off (01066) Streamlining On Off (01076) BdcA BdcA BdcA BdcA BdcA Ptn Assignment 123456 (01037) 101 Ptn Assignment 123456 (01047) Ptn Assignment 123456 (01057) · #dc Phone Number None (01070) BdcA BdcA DOWNLOADER PHONE Phone Number None (01060) Low Lvl Rpts On Off (01032) Exception Rpts On Off (01033) B` _A Ptn Assignment 123456 (01067) Ptn Assignment 123456 (01077) Concord B` _A B` _A 3+21(237,216 #dc · GLOBAL #dc · Phone Test On Off (02000) BdcA Auto Phone Test On Off (02001) BdcA Auto Test Reset On Off (02002) BdcA Comm Failure On Off (02003) BdcA DTMF Dialing On Off (02004) #dc B` _A PARTITION #dc · Local Phone Ctrl On Off (0210 - 0260) BdcA Remote Access On Off (0211 - 0261) BdcA Ring/Hang/Ring On Off (0212 - 0262) BdcA Line Fail Delay None (10-240 sec) (0213—Ptn 1 only) BdcA Toll Saver On Off (0214 - 0264) BdcA BdcA Dialer Abort On Off (02006) Phone Panic On Off (0215 - 0265) BdcA Dial Abort Delay 30 sec (15-120) (02007) BdcA Phone ACC Key · # (0216 - 0266) B` _A 7,0(56 · GLOBAL #dc · Supervisory Time 1:00 - 4:00 (Random) (0300) BdcA RF Tx Timeout 12 hours (2-24) (0302) BdcA Phone Test Freq. 7 days (1-255) (0303) BdcA Next Phone test 7 days (1-255) (0304) BdcA Output Trip Time 4 sec (1-12) (0305) BdcA Activity Timeout 24 hours (1-42) (0306) /,*+7 &21752/ · B` _A #dc B` _A PARTITION #dc · Entry Delay 30 sec (30-240) (0310 - 0360) BdcA Exit Delay 60 sec (45-184) (0011 - 0061) PARTITION · #dc Entry Lights None (3-9) (0400 - 0450) BdcA House Code 1B 2C 3D 4E 5F 6G (0401 - 0451) BdcA Extended Delay 4 min (1-8) (0312 - 0362) BdcA Siren Timeout 4 min (1-30) (0313 - 0363) BdcA Sleep Time 22:00 (00:00-23:50) (0314 - 0364) BdcA No Usage time (0315 - 0365) BdcA Daylight Saving On Off (0307) BdcA Cancel Message On Off (02008) BdcA Pager Delay 15 sec (0-30) (02009) BdcA Call Wait Cancel On Off 020010) BdcA Dial Tone Detect On Off (02011) Concord 102 B` _A 728&+3$' 237,216 #dc · GLOBAL #dc B` _A · Latchkey Zones None (1-96) (0500) 5(3257,1* #dc B` _A PARTITION #dc · Fire Panic On Off (0510 - 0560) BdcA Auxiliary Panic On Off (0511 - 0561) BdcA Police Panic On Off (0512 - 0562) BdcA Keychain TP Arm On Off (0513 - 0563) BdcA Star is No Delay On Off (0514 - 0564) · GLOBAL #dc · 24-Hour Tamper On Off (06000) BdcA Antenna Tamper On Off (06001) BdcA Buffer Control On Off (06002) BdcA Back In Service On Off (06003) BdcA Bypass Reports On Off (06004) BdcA Low CPU Battery On Off (06005) BdcA Battery Restoral On Off (06006) BdcA Buffer Full Report On Off (06007) BdcA Zone Restorals On Off (06008) BdcA Two Trip Error On Off (06009) BdcA TP Panic Rpt Fmt On Off (06010) BdcA AC Failure On Off (06011) B` _A PARTITION #dc · Opening Reports On Off (06100 - 06600) BdcA Closing Reports On Off (06101 - 06601) BdcA Recent Closings On Off (06102 - 06602) BdcA No Activity On Off (06103 - 06603) BdcA Duress Option On Off (06104 - 06604) BdcA Force Armed On Off (06105 - 06605) BdcA Latchkey Format On Off (06106 - 06606) BdcA Freeze Alarm On Off (06107 - 06607) BdcA Freeze Temp On Off (06108 - 06608) BdcA Alarm Verify On Off (06109 - 06609) BdcA System Tamper On Off (06110 - 06610) BdcA Report Confirm On Off (06112 - 06612) BdcA Receiver Failure On Off (06012) Bdc RF Low Bat Rpt On Off (06013) 103 RF Supv Rpt B` On Off _A (06014) Swinger Limit B` 1 (1-2) _A (06015) Aux Power Fail B` On Off _A (06016) Concord B` _A B` _A 6,5(1237,216 #dc · GLOBAL #dc · Immediate Beeps On Off (0700) BdcA Disable Trbl Beeps On Off (0701) BdcA UL 98 Options On Off (0702) 6(16256 #dc B` _A PARTITION #dc · Siren Verify On Off (0710—Ptn 1 only) · LEARN SENSORS (080) #dc · Sensor Partition 123456 #dc · Sensor Group 0 #dc · Trip Sensor n · #dc B` SENSOR TEXT _A (081) #dc · Text for Sensor n #dc · Sensor n Item 0 0- B` DELETE SENSORS B` EDIT SENSORS _A (082) _A (083) · #dc Delete Sensor n · #dc A Delete Sensor n Done · #dc Sn P1 Gnn NC/NO/TP RF/HW · #dc Sensor Partition n · #dc Sensor Group n BdcA Global Fire On Off (0703) BdcA Silent Panic On Off (0704) Concord 104 B` _A $8',2 9(5,),&$7,21 #dc · PARTITION 1 #dc · Audio Verify On Off (09000) BdcA Audio Mode 1 (09001) BdcA Fire Shutdown On Off (09002) BdcA Silent Talkback On Off (09003) BdcA Access Timeout 90 sec (30-300) (09004) BdcA Beep Delay 2 sec (0-300) (09005) BdcA Access Code **** (09006) B` _A $&(6625< 02'8/(6 #dc · BUS DEVICE #dc · B` _A SNAPCARDS (see next page) B` _A Device ID nnnnn B` _A Partition Assign 123456 B` _A Status Beeps On Off B` _A Key Beeps On Off B` _A Freeze Temp 42° F (40°-90° F) B` _A Temperature 40°-90° F B` _A Temperature 40°-90° F B` _A Output n B` _A Partition Assign 123456 B` _A Configuration ***** B` _A Cellular System AB Unit - ID On Off (10000 - 10015) #dc · CHANGE ID #dc · DEVICE PARTITION #dc · KEYPAD OPTIONS #dc · ENERGY OPTIONS #dc · OUTPUTS #dc · CELLULAR OPTIONS BdcA VOX Mic Gain 14 (01-64) (09007) BdcA VOX Gain Range 64 (01-64) (09008) BdcA Manual Mic Gain 04 (cannot change) (09009) BdcA VOX RX Gain 04 (01-10) (09010) 105 Concord $&(6625<02'8/(6 FRQW B` _A SNAPCARDS #dc · OUTPUT PROGRAMMING #dc · OUTPUT 1 B` _A OUTPUT TEXT #dc #` _· Partition Assign 123456 (101100) Configuration B` 01400 _A (101101) #` _· Partition Assign 123456 (101110) B` _A Configuration 00410 (101111) #` _· Partition Assign 123456 (101120) B` _A Configuration 00903 (101121) #` Partition Assign 123456 (101130) Configuration B` 40°-90° F _A (101131) BdcA OUTPUT 2 B` _A (10120) #` _· Output 1 Item n OUTPUT 2 #` Output 2 Item n (10121) #` _· Output 3 Item n #` _· Output 4 Item n _· BdcA BdcA OUTPUT 4 OUTPUT 1 BdcA BdcA OUTPUT 3 · OUTPUT 3 (10122) BdcA _· OUTPUT 4 (10123) 21%2$5'237,216 #dc · INPUTS #dc · Smoke Verify On Off (1100) BdcA Two-Wire Smoke On Off (1101 Concord B` _A OUTPUT PROGRAMMING #dc · OUTPUT 1 #dc · Partition Assign 123456 (11100) B` _A OUTPUT TEXT #dc B` _A OUTPUT 2 #dc · Partition Assign 123456 (11110) BdcA BdcA Configuration 00410 (11101) Configuration 00410 (11111) · OUTPUT 1 (1120) #dc · Output 1 Item n B` OUTPUT 2 _A (1121) · #dc Output 2 Item n 106 107 Concord System Wiring Notes Note 1 Class II power transformer must be plugged into an unswitched AC power receptacle. Do not short the transformer terminals together. The transformer contains an internal fuse that permanently disables the output if the terminals are shorted. Note 2 An alphanumeric touchpad is required for on-site programming. Note 3 Speaker terminals 7 and 8 activate only for alarms in partition 1. Use speakers with an 8ohm or higher impedance. Use 18-gauge, stranded wire. When connecting two or more 8ohm speakers, they must be wired in series as shown in the wiring diagram. Wiring two or more 8-ohm speakers in parallel can permanently damage the panel. Note 4 Onboard output 1 is a switched +12V rated for 1,000 mA maximum and output 2 is an opencollector type rated for 300 mA maximum. Output 1 defaults to configuration number 01614 (exterior siren). Output 2 defaults to configuration number 01710 (interior siren). Refer to panel installation instructions for all possible settings. Note 5 Zone (loop) wiring shown is an example that applies to all zones (except when zone 8 is configured for 2-wire smoke detectors). Install EOL resistors across all unused zone (loop) inputs. Note 6 For UL Listed installations, wire multiple supervised 2-wire hardwire smoke detectors (20 maximum) only as shown. Maximum 100 uA current draw per detector. Maximum 100 mA current draw in alarm. See page 12 for tested compatible models. Note 7 Some telephones are polarity-sensitive. Green and red wires may need to be reversed. Note 8 A maximum of two Audio Verification Modules (60-677) are allowed (partition 1 only). Wire multiple speakers in series, and power and microphone wires in parallel. Use shielded cable where shown in diagram to prevent cross-talk between the speaker and microphone. Audio Verification Modules shall not be used in UL Listed installations. Note 9 Connect multiple piezo sirens in parallel. Note 10 Refer to the SuperBus 2000 Energy Saver Module Installation Instructions for thermostat wiring details. Note 11 Wire Hardwire Module zone (loop) inputs as shown for the panel. Install EOL resistors across all unused zone (loop) inputs. Refer to the Module Installation Instructions for complete details. Note 12 Without AC power, panel shutdown occurs if battery voltage falls below 10.2 VDC. Concord 108 T E L C O 3 4 2 A B U S B S P E A K E R 7 6 5 8 O U T 1 O U T 2 + 1 2 V M IC G N D Z O N E 1 Z O N E 2 G N D Z O N E 3 Z O N E 4 G N D Z O N E 5 Z O N E 6 G N D Z O N E 7 9 1 0 1 1 1 2 1 3 1 4 1 5 1 6 1 7 1 8 1 9 2 0 2 1 2 2 2 3 2 4 GND A Class II 16.5 VAC 40 VA NOTE 4: Hardwire Interior Siren (13-949) NOTE 3: 8-Ohm, 15-watt Speaker (13-060) NOTE 1: Class II Power Transformer (600-1023 or 600-1024) 7 NOTE 5: Normally Open (N/O) Contacts in Parallel 8 NOTE 5: Normally Closed (N/C) Contacts in Series NOTE 4: Piezo Dynamic Exterior Siren (13-950) + B R N G R Y R E D 2 5 2 6 2 7 2 8 DB-8 Cord BRN + - Black Red NOTE 2: SuperBus 2000 2x16 LCD Alphanumeric Touchpad (60-746-01) shown. Others similar. NOTE 6: 2-Wire Smoke Detectors NOTE 5: PIR Motion Sensor (13-082) #1 G R N RED + 1 2 V GRY G N D BRN 1 V A C H O U S E GRN 1 6 .5 2 W S M K Z O N E 8 GRY NOTE 7: RJ-31X (CA-38A) Phone Jack L N L P GRN + - RED + 1 2 V 1 1 NOTES 3 & 8: Interrogator 200 Audio Verification Module (60-677) 2k-Ohm EOL Resistor (49-454) (Locate at last device) 2k-Ohm EOL Resistor (49-454) (Locate at last device) NOTE 3: Hardwire Interior Speaker (60-528) TELCO Protector Block Not Used G N D + 1 2 V 3 4 A B U S SuperBus 2000 319.5 MHz RF Transceiver Module (600-xxxxx-95R) (4 maximum) B GRN 6 5 RING (-) TIP (+) RED + 1 2 V WHT or YEL GRN RED A BLK B M IC G N D + 1 2 V 1 2 3 4 S P E A K E R 7 G N D To Panel Terminals 7 & 8 or SuperBus 2000 Phone Interface/Voice Module Terminals 6 & 7 Separate wire cables TO PHONE JACKS 8 Other SuperBus 2000 Module Connections G N D + 1 2 V 3 4 NOTE 10: SuperBus 2000 Energy Saver Module (60-620-01) B U S A B G N D 6 5 + 1 2 V 3 NOTE 10: SuperBus 2000 4-Relay Output Module (60-770) B U S A 4 5 2 3 F U R T H E R + 1 2 V 5 B U S B 6 1 2 3 4 5 6 7 8 9 3 4 B U S A 2 3 4 5 NOTES 3 & 7: SuperBus 2000 Phone Interface/Voice Module (60-777-01) B 6 1 + 1 2 V 5 6 7 8 9 A 2 B 3 4 G N D 5 G N D 6 7 S P K 1 S P K 2 8 9 1 0 A U D 1 A U D 2 G N D 1 1 T IP 1 1 2 T IP 2 1 3 R IN G 2 1 4 R IN G 1 BRN GRY 1 0 1 1 1 2 1 3 1 4 1 5 1 6 1 0 1 1 1 2 1 3 1 4 1 5 1 6 1 7 1 8 G N D Z O Z O Z O Z O Z O Z O Z O Z O Z O Z O Z O Z O N E N E N E N E N E N E N E N E N E N E N E N E G N D + 1 2 V 3 4 B U S A 5 B 6 S P E A K E R 7 8 G R N B R N G R Y R E D 2 5 2 6 2 7 2 8 GRN RED 1 3 2 4 5 8 C O M M O N 7 6 C O M M O N C O M M O N 2 C O M M O N 4 3 1 Z O N E C O M Z O N E 1 N O 4 C O M N C 4 N O 3 C O M N C 3 N O 2 C O M N C 2 N O 1 C O M N C 1 To Furnace To Thermostat A 4 + 1 2 V NOTE 10: SuperBus 2000 8Z Input Module (60-774) 6 1 1 G N D B (Partition 1 Voice Module Only) NOTE 7: RJ-31X CA-38A) Phone Jack
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Page Mode : UseThumbs XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39 Producer : Acrobat Distiller 6.0.1 (Windows) Creator Tool : FrameMaker 7.0 Modify Date : 2008:09:30 08:53:53-05:00 Create Date : 2004:10:19 07:25:53Z Metadata Date : 2008:09:30 08:53:53-05:00 Document ID : uuid:84300dbc-6147-4c6d-9984-4f7c8553678e Instance ID : uuid:2917942c-2f93-4df9-8321-8be9550ba442 Format : application/pdf Title : Untitled Document Has XFA : No Page Count : 114 Page Layout : SinglePage Creator : FrameMaker 7.0EXIF Metadata provided by EXIF.tools