CX I&M Manuals.qxp CX3000GS Continental CX3000 User Install Manual
User Manual: CX3000GS
Open the PDF directly: View PDF 
.
Page Count: 15
| Download | |
| Open PDF In Browser | View PDF |
Installation & Maintenance Instructions LIMITED WARRANTY Subject to the provisions of the clauses herein, Vendor agrees to correct any defect or defects in workmanship or materials which may develop under proper and normal use, by repair or by replacement of the defective part or equipment, at Vendor’s option, FOB factory. Unless otherwise stated, the warranty period shall be one (1) year from date of shipment. The exceptions to this warranty period are: CX Complete Air Purification Systems - Two (2) years This warranty is provided to the original Buyer, and may not be transferred, sold or bartered. Motors, drives, electrical controls and other components manufactured for Vendor by others are not covered by these warranty provisions. All warranty claims must be processed through point of purchase. All warranty repair work must be performed either at the factory or by a factory certified service center. For additional information regarding warranties, see Vendor USA ww.continentalfan.com Continental Fan Manufacturing Inc. 203 Eggert Road Buffalo, New York 14215 Tel: (800) 779 4021 Fax: (716) 842 0611 Canada www.aeroflo.com Aeroflo Inc. 12-205 Matheson Blvd. East Mississauga, Ontario L4Z 3E3 Tel: (905) 890 6192 Fax: (905) 890 6193 CX3000GS-I&M-1001 document: Limited Warranty-0909. CX3000GS Ducted Air Purifier PRODUCT SPECIFICATIONS TABLE OF CONTENTS PAGE SPECIFICATIONS Manufacturer: Continental Fan Manufacturing Inc. Model: CX3000GS Ducted Air Purifier Dimensions: 21” W x 25” H x 10” D Weight: 26 lbs Max Airflow: 2,170 cfm Max Air Velocity: 625 fpm Power Consumption: 45 watts Voltage: 120V/60 Hz Current: INSTALLATION INSTRUCTIONS • BEFORE INSTALLATION 2 • INSTALLATION 2 • TYPICAL HORIZONTAL SYSTEM 4 • TYPICAL VERTICAL SYSTEM 4 • WIRING DIAGRAM 5 OPERATION • AIR PURIFICATION 6 • SAFETY INSTRUCTIONS 7 0.6 amps • COST OF OPERATION 7 Fuse: AGC-2 • AIR CYCLES 7 Capacity: 4.0 to 5.0 tons UV Range: 254 nm (germicidal) • AIRFLOW & RESISTANCE DATA 8 Lamps: CX3000-RLGS - ultraviolet UVC lamps (2) • PARTICLE SIZE EFFICIENCY GRAPH 8 Filter: CX3000-RFGS - MERV-11 electrostatic filter • BACTERIA REDUCTION 9 • PARTICULATE FILTRATION 9 • PARTICLE REDUCTION 9 • REMOVAL EFFICIENCY OF TYPICAL ALLERGENS 9 • CARBON MONOXIDE REDUCTION 9 PERFORMANCE DATA Application: 3000 sq. ft. Service Interval: Lamps - 1 year Filter - 6 months Catalyst: Metal oxides (70 sq. ft.) MAINTENANCE REPLACEMENT PARTS Replacement parts are available from the following sources: • • • Your local HVAC wholesaler or contractor Continental Fan Manufacturing Inc., Buffalo, NY (1-800-779-4021) www.continentalfan.com • SERVICE INTERVALS 10 • REPLACING LAMPS 10 • REPLACING FILTER 11 • RESETTING SERVICE LIGHTS 11 PRODUCT SPECIFICATIONS • SPECIFICATIONS 12 • REPLACEMENT PARTS 12 • PARTS LIST 13 LIMITED WARRANTY READ AND SAVE THESE INSTRUCTIONS 12 1 1. 2. 3. 4. 5. INSTALLATION INSTRUCTIONS MAINTENANCE BEFORE INSTALLATION REPLACING FILTER Before installing the CX3000GS Ducted Air Purifier, inspect for any signs of damage. During handling and installation, take care to protect the honeycomb core of the photo-catalytic module. The titanium-aluminum core is very fragile and easily damaged. Do not install insulation within 3 inches (75 mm) of the ultraviolet UVC lamps. Access for service is required when mounting the CX3000GS above ceilings or behind walls. Do not install in such a manner that the interior photo-catalytic module may fall from an elevated position, and cause injury to people or equipment below. 1. 2. 3. Unplug the power cord from the CX3000GS unit. Unscrew the two locking knobs and remove the door. (Fig. 6) Remove old filter and replace with new MERV-11 electrostatic filter. Ensure that airflow arrow on filter points to the inside of module. (Fig. 7) INSTALLATION 1. Unscrew the two locking knobs and remove the inner module from the outer case. 2. Take care not to bend or distort the outer metal enclosure. 3. Ensure the unit is positioned so that the inlet, or return, air enters the side containing the MERV-11 electrostatic filter. (Fig. 1) 4. Mount the outer case to the support plenum. CAUTION: Use a screw length that will not penetrate the inside module containing the photo-catalytic module and MERV-11 electrostatic filter. There is only 1/2 inch of clearance between the outer case and inner module. 5. In the event the foot print of the air handler is larger or smaller than the outer metal enclosure of the CX3000GS unit, suitable metal transitions should be fabricated from 18 ga. sheet metal. (Fig. 2) 6. Tape all seams between the air handler and the outlet side of the CX3000GS to ensure there can be no air bypassing the system. 7. Attach the air handler to the outlet side of the CX3000GS with #10 x 3/8 selfdrilling sheet metal screws. 8. Slide the inner module into the outer case, and secure locking knobs finger tight only. Ensure the inner module can slide freely in and out of the outer case. 9. Plug the power cord into any 120 VAC outlet, and check both sight ports to ensure both lamps are illuminated. The ultraviolet lamps must remain on at all times. 10. Check the CX3000GS service panel. The LED service lights should flash in sequence for 15 seconds. The FILTER light should then turn flashing green, and the LAMP light a steady green. 11. Set the HVAC fan to operate for at least 30 minutes every hour. If air quality problems persist after one week, increase the fan operating time by 5 minute intervals, until suitable air quality is achieved. 2 Fig. 6 Fig. 7 RESETTING SERVICE LIGHTS On the right side of the service panel, there are arrows pointing to two small holes marked ‘RESET’. (Fig. 8) One is for the FILTER service light, and the other is for the LAMP service light. The service lights may be reset by inserting the end of a paper clip into the corresponding hole, and pushing lightly until the service light returns to green. SERVICE PANEL RESET LAMP OK SERVICE SERVICE NOW SOON FILTER RESET Fig. 8 11 MAINTENANCE INSTALLATION INSTRUCTIONS SERVICE INTERVALS AIRFLOW The CX3000GS Ducted Air Purifier has a built-in computer to automatically keep track of service intervals. LED service lights change color, 30 days in advance of required service, to indicate when the MERV-11 electrostatic filter or ultraviolet UVC lamps need replacement. Airflow • • MERV-11 Electrostatic Filter o Replace every 6 months o LED service light turns from green to yellow after 5 months, and to red after 6 months Filter Side Catalyst side Ultraviolet UVC Lamps o Replace every 12 months o LED service light turns from green to yellow after 11 months, and to red after 12 months REPLACING LAMPS Unplug the power cord from the CX3000GS unit. Unscrew the two locking knobs and remove the door. (Fig. 6) Remove photo-catalytic module. (Fig. 3) Unplug UVC lamps. (Fig. 4) Loosen retaining knobs and remove old UVC lamps. (Fig. 5) Install new UVC lamps, tightening only finger tight. Tighten retaining knobs and reconnect plug ends. Re-install photo-catalytic module and filter. Ensure that filter and photo-catalytic module are installed in proper airflow sequence. 9. Secure door. 10. Reconnect power cord. 11. Check both sight ports to ensure that both lamps are illuminated. 1. 2. 3. 4. 5. 6. 7. 8. Fig. 1 TRANSITIONS FOR IN-DUCT MOUNTING 20 Degree Expansion Per Side (4 in. Per Linear Foot) #10 Screws Not Longer Than 1/2 in. Return Air Duct Clean Air Out Transition Fig. 3 Fig. 4 10 Fig. 5 CX3000GS Fig. 2 3 Transition INSTALLATION INSTRUCTIONS PERFORMANCE DATA PARTICULATE FILTRATION BACTERIA REDUCTION TYPICAL HORIZONTAL SYSTEM Particle Reduction - First Pass Micro-organism Plate Count 0 1 17 30 Test Room 15’ L x 15’ W x 8’ H 42 65 0 15 30 45 60 Test Period In Hours Particle Size - Microns WHOLE HOME PARTICLE REDUCTION 100 TYPICAL VERTICAL SYSTEM Percent Reduction 90 Plenum 5.0 70 REMOVAL EFFICIENCY OF TYPICAL ALLERGENS 95.1 94.1 93.4 2,300 Sq. Foot Home 80 99.9% 99.7% 99.5% 99.3% 99.1% 98.9% 98.7% 98.5% 98.3% 98.1% 97.9% 97.7% 97.5% 97.3% 97.1% 96.9% 96.7% 96.5% 96.3% 96.1% 77.8 3.0 60 1.0 50 .5 40 .3 30 20 10 0 Fan Coil Unit 1 2 3 4 5 6 7 8 9 10 11 12 Hours of Operation CARBON MONOXIDE REDUCTION Gas Burners 250 Transition As Needed Airflow Parts Per Million - CO 225 CX3000GS Ducted Air Purifier Start 200 175 150 125 100 75 50 25 0 Finish 1 2 3 4 5 6 7 8 Time In Hours 4 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 9 PERFORMANCE DATA INSTALLATION INSTRUCTIONS AIRFLOW & RESISTANCE DATA WIRING DIAGRAM Airflow (cfm) Resistance (in. wg) Air Velocity (fpm) 1250 0.18 360 1500 0.20 432 1750 0.25 504 2000 0.35 576 2250 0.42 648 2500 0.55 720 WHITE BALLAST 120/220 V LAMP BLACK BALLAST 120/220 V LAMP WHITE 0.5u 0.7u 1.0u 5.0u 10u Particle Size - Microns 8 RECEPTACLE 0 0.3u Percent Reduction - First Pass LINE - RED 20 WHITE GROUND 40 5 NEUTRAL - WHITE 60 AGC2 BLUE RED 120 V BLUE 2 AMP FUSE 80 POWER CORD Removal Percentage 100 1 AMP SERVICE PANEL PARTICLE SIZE EFFICIENCY GRAPH TRANSFORMER BLACK WHITE BLACK OPERATION OPERATION AIR PURIFICATION SAFETY INSTRUCTIONS The CX3000GS Ducted Air Purifier is designed to operate with any heating or airconditioning system, up to five tons in size. It is rated for use at standard ambient air temperatures during heating and air-conditioning functions. It is not rated for operation at elevated air temperatures in excess of 125 F. 1. 2. 3. The CX3000GS uses a four-stage process to purify indoor air: 1. 2. 3. 4. Electrostatic MERV-11 Filter - removes 0.3 micron allergens and dust Reactive Catalyst - destroys VOC’s, toxic chemicals and odors UVC Germicidal Light - kills germs, viruses and bacteria on contact Negative Ions and Activated Oxygen - keep air fresh and clean Air purification and sterilization occur whenever the HVAC system fan is operating. The ultraviolet UVC lamps are always on. They continuously clean and reactivate the catalyst by burning off surface impurities during periods of non-use, or no airflow. Do not attempt to clean the photo-catalytic honeycomb core with cleaning solutions. It is recommended that the CX3000GS operate at least 30 minutes per hour, 24 hours per day, to remove toxic materials from an indoor environment. For individuals who may be sensitive to mold spores, dust mites or chemicals, or have respiratory problems such as asthma, emphysema and chronic allergies, the operating time should be extended to 40 minutes or more per hour. The actual time of operation depends on many factors, including the level of ambient pollution or pollen levels, and individual sensitivity to allergens. It is recommended that a programmable thermostat be used. These can be set to provide continuous air circulation, and thus air purification, even when the HVAC system is not calling for heating or cooling. Never look into a burning ultraviolet lamp without proper eye protection, as severe eye damage may result. Always unplug the power cord from the unit when changing the filter or ultraviolet UVC lamps. Do not attempt to clean the photo-catalytic honeycomb core with cleaning solutions. The catalyst is constantly radiated by short wave ultraviolet UVC light during operation, and is self-cleaning. COST OF OPERATION (Calculations are based on continuous operation, 24 hours per day, and an energy consumption of 32.25 kw-hrs per month) ELECTRICITY COST (per kw-hr) MONTHLY COST ANNUAL COST $0.06 $1.93 $23.16 $0.08 $2.58 $30.96 $0.10 $3.22 $38.64 AIR CYCLES (Calculations are based on a floor area of 3,000 sq. ft.) FAN OPERATING PERIOD AIR CYCLES PER HOUR AIR CYCLES PER DAY 10 minutes per hour 0.9 21 20 minutes per hour 1.8 42 30 minutes per hour 2.7 63 An AirCycler may be purchased from the following sources: 40 minutes per hour 3.6 84 • • • 50 minutes per hour 4.5 105 60 minutes per hour 5.4 126 In the event an existing thermostat does not have the capability to operate the fan independently, it is recommended that an AirCycler be installed. An AirCycler is a device that is wired in parallel with existing thermostat wiring, and can be programmed to turn on the HVAC system fan for any desired time interval. A builtin memory chip tracks the time that a fan operates every hour, and energizes the fan only if normal requirements for heating and air conditioning have not cycled the fan unit long enough to meet pre-determined air purification requirements. Your local HVAC wholesaler or contractor Shelter Supply, Lakeville, MN (1-800-762-8399) www.AirCycler.com 6 7 OPERATION OPERATION AIR PURIFICATION SAFETY INSTRUCTIONS The CX3000GS Ducted Air Purifier is designed to operate with any heating or airconditioning system, up to five tons in size. It is rated for use at standard ambient air temperatures during heating and air-conditioning functions. It is not rated for operation at elevated air temperatures in excess of 125 F. 1. 2. 3. The CX3000GS uses a four-stage process to purify indoor air: 1. 2. 3. 4. Electrostatic MERV-11 Filter - removes 0.3 micron allergens and dust Reactive Catalyst - destroys VOC’s, toxic chemicals and odors UVC Germicidal Light - kills germs, viruses and bacteria on contact Negative Ions and Activated Oxygen - keep air fresh and clean Air purification and sterilization occur whenever the HVAC system fan is operating. The ultraviolet UVC lamps are always on. They continuously clean and reactivate the catalyst by burning off surface impurities during periods of non-use, or no airflow. Do not attempt to clean the photo-catalytic honeycomb core with cleaning solutions. It is recommended that the CX3000GS operate at least 30 minutes per hour, 24 hours per day, to remove toxic materials from an indoor environment. For individuals who may be sensitive to mold spores, dust mites or chemicals, or have respiratory problems such as asthma, emphysema and chronic allergies, the operating time should be extended to 40 minutes or more per hour. The actual time of operation depends on many factors, including the level of ambient pollution or pollen levels, and individual sensitivity to allergens. It is recommended that a programmable thermostat be used. These can be set to provide continuous air circulation, and thus air purification, even when the HVAC system is not calling for heating or cooling. Never look into a burning ultraviolet lamp without proper eye protection, as severe eye damage may result. Always unplug the power cord from the unit when changing the filter or ultraviolet UVC lamps. Do not attempt to clean the photo-catalytic honeycomb core with cleaning solutions. The catalyst is constantly radiated by short wave ultraviolet UVC light during operation, and is self-cleaning. COST OF OPERATION (Calculations are based on continuous operation, 24 hours per day, and an energy consumption of 32.25 kw-hrs per month) ELECTRICITY COST (per kw-hr) MONTHLY COST ANNUAL COST $0.06 $1.93 $23.16 $0.08 $2.58 $30.96 $0.10 $3.22 $38.64 AIR CYCLES (Calculations are based on a floor area of 3,000 sq. ft.) FAN OPERATING PERIOD AIR CYCLES PER HOUR AIR CYCLES PER DAY 10 minutes per hour 0.9 21 20 minutes per hour 1.8 42 30 minutes per hour 2.7 63 An AirCycler may be purchased from the following sources: 40 minutes per hour 3.6 84 • • • 50 minutes per hour 4.5 105 60 minutes per hour 5.4 126 In the event an existing thermostat does not have the capability to operate the fan independently, it is recommended that an AirCycler be installed. An AirCycler is a device that is wired in parallel with existing thermostat wiring, and can be programmed to turn on the HVAC system fan for any desired time interval. A builtin memory chip tracks the time that a fan operates every hour, and energizes the fan only if normal requirements for heating and air conditioning have not cycled the fan unit long enough to meet pre-determined air purification requirements. Your local HVAC wholesaler or contractor Shelter Supply, Lakeville, MN (1-800-762-8399) www.AirCycler.com 6 7 PERFORMANCE DATA INSTALLATION INSTRUCTIONS AIRFLOW & RESISTANCE DATA WIRING DIAGRAM Airflow (cfm) Resistance (in. wg) Air Velocity (fpm) 1250 0.18 360 1500 0.20 432 1750 0.25 504 2000 0.35 576 2250 0.42 648 2500 0.55 720 WHITE BALLAST 120/220 V LAMP BLACK BALLAST 120/220 V LAMP WHITE 0.5u 0.7u 1.0u 5.0u 10u Particle Size - Microns 8 RECEPTACLE 0 0.3u Percent Reduction - First Pass LINE - RED 20 WHITE GROUND 40 5 NEUTRAL - WHITE 60 AGC2 BLUE RED 120 V BLUE 2 AMP FUSE 80 POWER CORD Removal Percentage 100 1 AMP SERVICE PANEL PARTICLE SIZE EFFICIENCY GRAPH TRANSFORMER BLACK WHITE BLACK INSTALLATION INSTRUCTIONS PERFORMANCE DATA PARTICULATE FILTRATION BACTERIA REDUCTION TYPICAL HORIZONTAL SYSTEM Particle Reduction - First Pass Micro-organism Plate Count 0 1 17 30 Test Room 15’ L x 15’ W x 8’ H 42 65 0 15 30 45 60 Test Period In Hours Particle Size - Microns WHOLE HOME PARTICLE REDUCTION 100 TYPICAL VERTICAL SYSTEM Percent Reduction 90 Plenum 5.0 70 REMOVAL EFFICIENCY OF TYPICAL ALLERGENS 95.1 94.1 93.4 2,300 Sq. Foot Home 80 99.9% 99.7% 99.5% 99.3% 99.1% 98.9% 98.7% 98.5% 98.3% 98.1% 97.9% 97.7% 97.5% 97.3% 97.1% 96.9% 96.7% 96.5% 96.3% 96.1% 77.8 3.0 60 1.0 50 .5 40 .3 30 20 10 0 Fan Coil Unit 1 2 3 4 5 6 7 8 9 10 11 12 Hours of Operation CARBON MONOXIDE REDUCTION Gas Burners 250 Transition As Needed Airflow Parts Per Million - CO 225 CX3000GS Ducted Air Purifier Start 200 175 150 125 100 75 50 25 0 Finish 1 2 3 4 5 6 7 8 Time In Hours 4 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 9 MAINTENANCE INSTALLATION INSTRUCTIONS SERVICE INTERVALS AIRFLOW The CX3000GS Ducted Air Purifier has a built-in computer to automatically keep track of service intervals. LED service lights change color, 30 days in advance of required service, to indicate when the MERV-11 electrostatic filter or ultraviolet UVC lamps need replacement. Airflow • • MERV-11 Electrostatic Filter o Replace every 6 months o LED service light turns from green to yellow after 5 months, and to red after 6 months Filter Side Catalyst side Ultraviolet UVC Lamps o Replace every 12 months o LED service light turns from green to yellow after 11 months, and to red after 12 months REPLACING LAMPS Unplug the power cord from the CX3000GS unit. Unscrew the two locking knobs and remove the door. (Fig. 6) Remove photo-catalytic module. (Fig. 3) Unplug UVC lamps. (Fig. 4) Loosen retaining knobs and remove old UVC lamps. (Fig. 5) Install new UVC lamps, tightening only finger tight. Tighten retaining knobs and reconnect plug ends. Re-install photo-catalytic module and filter. Ensure that filter and photo-catalytic module are installed in proper airflow sequence. 9. Secure door. 10. Reconnect power cord. 11. Check both sight ports to ensure that both lamps are illuminated. 1. 2. 3. 4. 5. 6. 7. 8. Fig. 1 TRANSITIONS FOR IN-DUCT MOUNTING 20 Degree Expansion Per Side (4 in. Per Linear Foot) #10 Screws Not Longer Than 1/2 in. Return Air Duct Clean Air Out Transition Fig. 3 Fig. 4 10 Fig. 5 CX3000GS Fig. 2 3 Transition 1. 2. 3. 4. 5. INSTALLATION INSTRUCTIONS MAINTENANCE BEFORE INSTALLATION REPLACING FILTER Before installing the CX3000GS Ducted Air Purifier, inspect for any signs of damage. During handling and installation, take care to protect the honeycomb core of the photo-catalytic module. The titanium-aluminum core is very fragile and easily damaged. Do not install insulation within 3 inches (75 mm) of the ultraviolet UVC lamps. Access for service is required when mounting the CX3000GS above ceilings or behind walls. Do not install in such a manner that the interior photo-catalytic module may fall from an elevated position, and cause injury to people or equipment below. 1. 2. 3. Unplug the power cord from the CX3000GS unit. Unscrew the two locking knobs and remove the door. (Fig. 6) Remove old filter and replace with new MERV-11 electrostatic filter. Ensure that airflow arrow on filter points to the inside of module. (Fig. 7) INSTALLATION 1. Unscrew the two locking knobs and remove the inner module from the outer case. 2. Take care not to bend or distort the outer metal enclosure. 3. Ensure the unit is positioned so that the inlet, or return, air enters the side containing the MERV-11 electrostatic filter. (Fig. 1) 4. Mount the outer case to the support plenum. CAUTION: Use a screw length that will not penetrate the inside module containing the photo-catalytic module and MERV-11 electrostatic filter. There is only 1/2 inch of clearance between the outer case and inner module. 5. In the event the foot print of the air handler is larger or smaller than the outer metal enclosure of the CX3000GS unit, suitable metal transitions should be fabricated from 18 ga. sheet metal. (Fig. 2) 6. Tape all seams between the air handler and the outlet side of the CX3000GS to ensure there can be no air bypassing the system. 7. Attach the air handler to the outlet side of the CX3000GS with #10 x 3/8 selfdrilling sheet metal screws. 8. Slide the inner module into the outer case, and secure locking knobs finger tight only. Ensure the inner module can slide freely in and out of the outer case. 9. Plug the power cord into any 120 VAC outlet, and check both sight ports to ensure both lamps are illuminated. The ultraviolet lamps must remain on at all times. 10. Check the CX3000GS service panel. The LED service lights should flash in sequence for 15 seconds. The FILTER light should then turn flashing green, and the LAMP light a steady green. 11. Set the HVAC fan to operate for at least 30 minutes every hour. If air quality problems persist after one week, increase the fan operating time by 5 minute intervals, until suitable air quality is achieved. 2 Fig. 6 Fig. 7 RESETTING SERVICE LIGHTS On the right side of the service panel, there are arrows pointing to two small holes marked ‘RESET’. (Fig. 8) One is for the FILTER service light, and the other is for the LAMP service light. The service lights may be reset by inserting the end of a paper clip into the corresponding hole, and pushing lightly until the service light returns to green. SERVICE PANEL RESET LAMP OK SERVICE SERVICE NOW SOON FILTER RESET Fig. 8 11 PRODUCT SPECIFICATIONS TABLE OF CONTENTS PAGE SPECIFICATIONS Manufacturer: Continental Fan Manufacturing Inc. Model: CX3000GS Ducted Air Purifier Dimensions: 21” W x 25” H x 10” D Weight: 26 lbs Max Airflow: 2,170 cfm Max Air Velocity: 625 fpm Power Consumption: 45 watts Voltage: 120V/60 Hz Current: INSTALLATION INSTRUCTIONS • BEFORE INSTALLATION 2 • INSTALLATION 2 • TYPICAL HORIZONTAL SYSTEM 4 • TYPICAL VERTICAL SYSTEM 4 • WIRING DIAGRAM 5 OPERATION • AIR PURIFICATION 6 • SAFETY INSTRUCTIONS 7 0.6 amps • COST OF OPERATION 7 Fuse: AGC-2 • AIR CYCLES 7 Capacity: 4.0 to 5.0 tons UV Range: 254 nm (germicidal) • AIRFLOW & RESISTANCE DATA 8 Lamps: CX3000-RLGS - ultraviolet UVC lamps (2) • PARTICLE SIZE EFFICIENCY GRAPH 8 Filter: CX3000-RFGS - MERV-11 electrostatic filter • BACTERIA REDUCTION 9 • PARTICULATE FILTRATION 9 • PARTICLE REDUCTION 9 • REMOVAL EFFICIENCY OF TYPICAL ALLERGENS 9 • CARBON MONOXIDE REDUCTION 9 PERFORMANCE DATA Application: 3000 sq. ft. Service Interval: Lamps - 1 year Filter - 6 months Catalyst: Metal oxides (70 sq. ft.) MAINTENANCE REPLACEMENT PARTS Replacement parts are available from the following sources: • • • Your local HVAC wholesaler or contractor Continental Fan Manufacturing Inc., Buffalo, NY (1-800-779-4021) www.continentalfan.com • SERVICE INTERVALS 10 • REPLACING LAMPS 10 • REPLACING FILTER 11 • RESETTING SERVICE LIGHTS 11 PRODUCT SPECIFICATIONS • SPECIFICATIONS 12 • REPLACEMENT PARTS 12 • PARTS LIST 13 LIMITED WARRANTY READ AND SAVE THESE INSTRUCTIONS 12 1 PRODUCT SPECIFICATIONS PARTS LIST PART NUMBER DESCRIPTION AL006 Photo-Catalytic Module (Honeycomb Core) BL007 12 Volt Transformer BL014 Electronic Lamp Ballast CX3000-RFGS MERV-11 Electrostatic Filter CX3000-RLGS Ultraviolet UVC Lamps (Set of 2) CX3000-RFLGS 1 Year Replacement Parts Kit, comprising: • (2) CX3000-RFGS • (1) CX3000-RLGS 13 Installation & Maintenance Instructions LIMITED WARRANTY Subject to the provisions of the clauses herein, Vendor agrees to correct any defect or defects in workmanship or materials which may develop under proper and normal use, by repair or by replacement of the defective part or equipment, at Vendor’s option, FOB factory. Unless otherwise stated, the warranty period shall be one (1) year from date of shipment. The exceptions to this warranty period are: CX Complete Air Purification Systems - Two (2) years This warranty is provided to the original Buyer, and may not be transferred, sold or bartered. Motors, drives, electrical controls and other components manufactured for Vendor by others are not covered by these warranty provisions. All warranty claims must be processed through point of purchase. All warranty repair work must be performed either at the factory or by a factory certified service center. For additional information regarding warranties, see Vendor www.continentalfan.com www.continentalf an.com better AIRFLOW by DESIGNTM USA - Continental Fan Manufacturing Inc. Canada - Continental Fan Canada Inc. 203 Eggert Road, Buffalo, NY 14215 T: 716-842-0670 • F: 716-842-0611 12-205 Matheson Blvd E, Mississauga, ON L4Z 3E3 T: 905-890-6192 • F: 905-890-6193 CX3000GS-I&M-1001-11 document: Limited Warranty-1103. CX3000GS Ducted Air Purifier
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 15 Has XFA : No XMP Toolkit : XMP toolkit 2.9.1-14, framework 1.6 About : uuid:3a3623db-6d6c-438e-9553-ba3387d5fa49 Producer : Acrobat Distiller 6.0.1 (Windows) Create Date : 2010:01:21 11:06:15-05:00 Creator Tool : PScript5.dll Version 5.2.2 Modify Date : 2011:03:23 11:21:44-04:00 Metadata Date : 2011:03:23 11:21:44-04:00 Document ID : uuid:be4cdd71-0337-4e70-bff2-84c5bedaa8dc Format : application/pdf Title : CX I&M manuals.qxp Creator : jpfister Author : jpfisterEXIF Metadata provided by EXIF.tools