Curtis Compressor Challenge Air

User Manual: Curtis-Compressor-Challenge-Air Igor's of metalworking and electrical manuals

Open the PDF directly: View PDF .
Page Count: 44

CAP-600X

MAY, 2005

WARNING

Before installing and operating this compressor, read

and understand the safety precautions contained in

LV-474 supplement to and part of CAP-600

BY PERFORMANCE DATA SHEET.

REFER TO MODEL & SERIAL NUMBER.

R.P.M. OR ABOVE MAX. AS STIPULATED

DO NOT OPERATE LOWER THAN 500

READ INSTAL. & OPERATION INSTR.

SERIAL NO.MODEL NO.

1905 Kienlen Avenue

St. Louis, MO 63133

CURTIS-TOLEDO, INC.

IMPORTANT

Make a permanent record of the

Model and Serial number of

your machine here. You’ll save

time and expense by including

this reference identification on

replacement part orders.

*CONSULT FACTORY FOR SPECIAL APPLICATIONS

CURTIS-TOLEDO, INC.

1905 Kienlen Avenue, St. Louis, Missouri 63133

phone: 314-383-1300 fax: 314-381-1439

Sales representatives in principal cities

info@curtistoledo.com

CAP-600

2

INSTALLATION

CONGRATULATIONS on your new Curtis

Challenge Air Compressor. Please examine the

compressor for shipping damage(s) and if any are

found report it immediately to the carrier.

Select a clean dry location with a rigid floor strong

enough to support the compressor. If the

compressor is to be located in an area where

vibration is critical, properly engineered vibration

mounts and flexible piping should be used.

Remove the skid. NOTE: The compressor should

never be operated on the shipping skid. Level

the compressor so it can be bolted down securely.

Before tightening the bolts, check to see that all

four feet are resting on the foundation. Shim as

necessary to eliminate stress on the receiver or

base when the bolts are tightened. We suggest

using a level for proper alignment.

Maximum ambient temperature in which the

compressor and motor should be operated is

104°F. Therefore, adequate ventilation must be

provided.

The suction openings of the compressor are

equipped with a combination air filter-muffler to

protect the compressor from normal dust and other

harmful substances. If the air around the

compressor is excessively hot, dusty, humid or

contaminated with foreign gases (such as ammonia

or acid fumes) move the filter-muffler to a remote

point where the air is clean, cool and dry. Run a

pipe to the compressor suction opening. If the run

is over 50 feet in length, use a larger pipe to avoid

excessive pressure drop. In order to fit the filter to

the compressor, bush down the connections. Be

sure piping and fittings are clean and free from dirt

and chips. If the filter is installed outside, check to

insure that it is located above the normal outside

dust level, and that rain cannot enter the filter

element. Where the relocation of the filter-muffler

is not possible or feasible, an oil bath filter is

recommended and is available from Curtis.

On basic or base mounted compressors run a

discharge pipe to the receiver or optional

aftercooler and bush up or down as necessary.

The pipe should enter near the top of the receiver.

Keep in mind that condensate may form in the

discharge line; therefore, the lines should always

be pitched to drain condensate away from the

compressor. Always provide a safety relief valve in

the discharge line between the compressor and in-

line shutoff valves. If more than one compressor

pumps into a common system, a check valve in the

discharge line of each compressor is recommended

to prevent moisture from entering the cylinder head

when one compressor is idle. A globe or gate valve

installed in the discharge line will allow compressor

isolation from plant air system for compressor

maintenance. (Note: A safety relief valve should be

located between the compressor and the

globe/gate valve.)

Check the electrical supply for voltage, phase, and

frequency to see that they match the nameplate

stampings on the motor, magnetic starter,

solenoids, and other controls. Use electrical wires

of adequate size to carry the full load current of the

motor without excessive voltage drop. Charts are

available from Curtis (upon request) to provide

information on this. The motor must always be

protected by a starter with properly sized thermal

overload(s). The starter should protect the motor

from overheating and burnout due to an overload,

low voltage or single phasing of a 3-phase circuit.

Failure to install the proper starter and

overloads will void the motor manufacturers

warranty. Follow the National Electric Code or

local electric code in providing wiring, fusing and

disconnect switches. NOTE: Do not close the

disconnect switch to start the compressor until

the procedures outlined under "Startup

Procedures" have been completed.

LIMITED SAFETY PRECAUTIONS

(Also see supplement LV-474)

The following safety precautions are recommended

in the use of this compressor:

1. Use a totally enclosed OSHA-approved belt

guard to cover the drive assembly. Where

possible, place the flywheel toward the wall, and

mount the unit a minimum distance of 2 feet from

the wall for maintenance convenience.

2. Turn off & lock out the electrical disconnect

switch before working on the unit to prevent the

unit from starting unexpectedly

3. Release all air pressure from the system before

working on the unit and red tag all electrical

control switches, for safety precaution.

4. Do not by-pass motor over-current protection.

5. Do not change the setting or in any way affect

the operation of the safety valve.

6. Keep unit securely anchored so that movement

will not put a strain on piping, wiring, or air

receiver.

WARNING: Read and understand supplement LV-474 before installing and operating the compressor.

CAP-600

3

START-UP PROCEDURES

OIL RECOMMENDATION

Use a good grade of industrial compressor oil (non-

detergent) with foam, rust and oxidation inhibitors and a

minimum life of 1500 hours in the ASTM D 943 test for

oxidation stability.

Ambient Temperatures:

0 - 32º F - Viscosity 180 to 240 SUS at 100º F.

Minimum pour point of - 20º F.

Grade ISO 4

Approved listing:

Chevron-Turban GST Oil 46.

Amoco-Amokon Oil 46.

Conoco-Turban Oil 46.

Shell-Turbo Oil T-46.

Texaco-Regal R & O Oil 46.

Exxon- Teresstic Oil 46

32 - 100º F - Viscosity 300 to 350 SUS at 100º F.

Grade ISO

Approved listing:

Chevron-Turban GST Oil 68.

Amoco-Amokon Oil 68.

Conoco-Turban Oil 68.

Shell-Turbo Oil T-68.

Texaco-Regal R & O Oil 68.

Exxon- Teresstic Oil 68

100 - 110º F - Viscosity 450 to 550 SUS at 100º F.

Grade ISO 100.

Approved listing:

Chevron-Turban GST Oil 100.

Amoco-Amokon Oil 100.

Conoco-Turban Oil 100.

Shell-Turbo Oil T-100.

Texaco-Regal R & O Oil 100.

Exxon- Teresstic Oil 100

If the compressor is equipped with an automatic start-stop

control (with pressure switch unloading), it is automatically

unloaded upon starting, and will automatically load after

attaining running speed. If the compressor is equipped with

a constant speed control (pilot valve unloading), it is

necessary to manually unload the compressor, if there is

pressure in the discharge line, in order to achieve an

unloaded start. The compressor must be manually loaded

after the compressor has attained full running speed,

thereafter, it functions automatically to maintain operating

pressure until the unit is shut off.

Close the disconnect switch and start the compressor.

Observe the direction of rotation, which should be

counterclockwise when viewed from the flywheel side of the

compressor on all models. For single-phase units, the

direction of rotation is determined by the motor nameplate

instructions, and is adjusted at the factory. For three-phase

units, if the rotation is incorrect, stop the unit and

interchange any two of the three wires to the motor at the

disconnect switch. This will reverse the direction of rotation

of the motor and compressor.

PREVENTIVE MAINTENANCE

A good maintenance program will add years of service to

your air compressor. The following is recommended as a

minimum maintenance program. (TURN OFF POWER

BEFORE SERVICING.)

LUBRICATION

1. For proper lubrication the compressor shall not be

operated below the minimum or above the maximum R. P.M.

recommended for the various models.

2. Maintain oil level mid-way between the upper and lower lines

of the crankcase sight gage. NOTE ILLUSTRATION:

3. Stop compressor to add and gauge oil.

4. Do not fill above the upper line and do not operate compressor

with oil level below the lower line.

DO NOT OVER FILL

5. Change oil at the first 100 hours of operation and 1000 hours

thereafter, or as required. It may be necessary to change oil

more frequent due to abnormal humid and contaminated

conditions.

DAILY MAINTENANCE

1. Check and maintain oil level at centerline of sight glass and

add oil as necessary.

2. Drain condensate from receiver unless it is equipped with an

automatic tank drain, in which case the drain should be

checked weekly to see that it is operating. See automatic tank

drain instructions.

3. Check for unusual noise or vibration (See "Trouble Shooting".)

WEEKLY MAINTENANCE

1. Clean the air filters. A clogged air filter can seriously affect the

efficiency of the compressor and cause overheating and oil

usage.

2. Clean all external parts of the compressor and driver. Be sure

to clean the intercooler-finned surface on two-stage

compressors. A dirty compressor will cause abnormally high

discharge temperature and resulting oil carbonization on

internal valve components

3. Check the safety valve manually (by pulling ring or lever) to

see that it is not stuck.

MONTHLY MAINTENANCE

1. Inspect the entire air system for leaks.

2. lnspect condition of oil and change if necessary.

3. Check drive belt tension and tighten if needed.

EVERY 3 MOS. OR 1,000 HRS. OF OPERATION

1. Change oil.

2. lnspect valves. Clean the carbon from valves and head if

necessary.

3. Check and tighten if necessary all bolts, nuts, etc.

4. Check unloader operation.

*CHECKING BELT TENSION

The v-belt(s) should be adjusted so that a declination of about 3/8

– 1/2 inch will be obtained when it is pushed by a finger at the

middle point as shown in Figure 1.

CAUTION: Over tightening the v-belt(s) will result in

overloading of the motor and belt failure, while a loose belt

will be slipping and resulting in an unstable speed,

overheating the belt and high amp draw.

WARNING: Read and understand supplement LV-474 before installing and operating the compressor.

CAP-600

4

Figure 1

To change tension, loosen the motor hold-down bolts and

slide the motor on the base, using a lever if necessary, or

by turning the adjusting bolt at the end of the base.

Retighten motor hold-down bolts.

NOTE: Do not over tighten belts.

ELECTRIC MOTOR

Grease once a year with a good grade of lithium ball

bearing grease, or as directed by the motor manufacturer.

VALVE INSPECTION AND MAINTENANCE

Valves should be inspected at regular intervals as

recommended under "Maintenance" and cleaned or

replaced when necessary. The valve can be serviced

without disconnecting air piping or removing the head.

(Be sure the power to the motor is disconnected and

all pressure released before starting to work on the

compressor.)

On constant run models, it is necessary to remove the

unloader piping before the valve plugs can be removed.

MODELS E-11 AND E-23 (Figures 2 and 3)

A. Disassembly:

1. Unbolt the outlet valve push cover (70112- 11450).

2. Remove the outlet valve push cover packing (70112-

11650), spring (70112-41070) and valve plate (70112-

31030). CAUTION: Steps 1 and 2 are for outlet

valve.

3. Remove the unloading connecting tube for Models

E-11 and E-23.

4. Untighten four cylinder head fixed bolts.

5. Remove cylinder head carefully and turn it over.

6. Unbolt inlet valve receiver (70112-31020).

7. Remove valve spring (70112-31070) and valve plate

(70112-31030).

Valves should be inspected approximately every 1,000

hours of operation. Inspect the valve seats on

cylinder head for dents, cracks or wear. Replace all

defective parts. Remove carbon deposits and wash all

valve components in a suitable non-flammable

cleaning fluid.

B. Assembly:

1. Place outlet valve plate (70112-31030) in position.

2. Place the outlet valve push cover packing (70112-

11650) in position.

3. Insert the spring (70112-41070) into outlet valve push

cover (70112-11450).

4. Turn outlet valve push cover (70112-11450) in position

carefully.

5. Check the valves to see if they can move freely in their

guides.

6. Turn over the cylinder head (70112-11010).

7. Place the inlet valve plate (70112-31030) in position.

8. Insert the small end of inlet valve spring (70112-

31070) into position of valve receiver (70112- 31020).

9. Screw inlet valve receiver in position.

10. Check the valves to see if they can move freely in their

guides and do not pinch or bind between the seat and

guard legs.

Figure 2

Figure 3

WARNING: Read and understand supplement LV-474 before installing and operating the compressor.

CAP-600

5

MODELS E-50, E-71 AND E-15 (Figures 4 and 5)

A. Disassembly of Inlet Valve Assembly (Figure 4).

1. Untighten the hex nut.

2. Remove unloading fork (70123-31080), unloading fork

guide (70123-31090), unloading spring (70123-11230)

and valve seat (70123-31010).

CAUTION:

1. If a vise is used to hold the valve assembly, be

careful not to clamp the assembly too tight.

2. Valve assembly should be inspected approximately

every 1,000 hours of operation.

3. Inspect the valve seat for dents, cracks or wear.

4. Replace all defective parts.

5. Valve seats that might be worn after years of

operation can be re-lapped or re-ground, in this

case the recess in which the valve guard legs fit

must also be cut down accordingly to ensure a

same valve lift.

FIGURE 4 (EXAMPLE SHOWN E-50)

FIGURE 5 (EXAMPLE SHOWN E-50)

6. Remove carbon deposits and wash all valve

components in a suitable non-flammable cleaning

fluid.

B. Reassembly of Inlet Valve Assembly

1. Place valve spring (70123-31070) and valve plate

(70123-31030) on valve receiver (70123-31020).

2. Place valve seat (70123-31010), unloading fork guide

70123-31090), unloading spring (70123- 11230) and

unloading fork (70123-31080) respectively.

3. Tighten the valve assembly by tightening the hex nut.

4. Check the valves to see if they can move freely in their

guides and do not pinch or bind between the seat and

guard legs.

C. Disassembly of Outlet Valve Assembly (Figure 5)

1. Untighten the hex nuts.

2. Remove valve receiver (70123-41020), valve spring

(70123-41070) and valve plate (70123-31030).

CAUTION: Refer to disassembly of inlet valve assembly

(paragraph B).

D. Reassembly of Outlet Valve Assembly

1. Place valve spring (70123-41070) in valve receiver

70123-41020).

2. Place valve plate (70123-31030) in valve receiver.

(70123-41020).

3. Insert the sub-assembled part (assembled in

step I and 2) into valve seat (70123-41010).

4. Tighten the hex nuts.

5. Check the valves to see if they can move freely in their

guides and do not pinch or bind between the seat and

guard legs.

WARNING: Read and understand supplement LV-474 before installing and operating the compressor.

CAP-600

6

VALVE ASSEMBLY INSTALLATION - E-50 MODEL

(Figures 6 and 7)

1. Install valve assembly gasket (70123-11110)

2. Install valve assembly (70123-31000).

3. Install valve push cover (70123-11150).

4. Install head bolt and tighten evenly and securely.

It is strongly recommended that a Preventative

Maintenance Kit & Valve/Gasket Maintenance Kit be kept

on hand. In this manner, the valves can be used in turn to

keep the compressor always in good condition and a

minimum downtime.

FIGURE 6

PISTON RINGS (Rebuild Kit)

To inspect or replace piston rings as follows:

1. Remove cylinder head.

2. Remove cylinder.

3. Loosen the connecting rod bolts.

4. Push out the piston with piston rings and connecting

rod.

5. To remove the old rings, pry them out of their grooves

and slide them over the piston. Care should be taken

not to damage the piston.

6. Inspect the ring grooves for nicks and carbon deposits.

Clean the ring grooves and remove the obstructions,

which might prevent the rings from moving freely.

To install new rings on the piston as follows: (Be

careful not to damage the piston and rings).

1. Install the oil control ring (70123-61050) first. Rotate

ring in groove to make sure it is free.

2. Install the Compression ring (70123-61030). Make sure

the "top" or "R" mark is exactly on top. If not, it might

cause excessive oil consumption.

3. Repeat the process with other rings, if any.

4. Assemble connecting rod into the crankshaft. Be sure

that the connecting rod and its cap are in original pair

and position, since the connecting rod cap and

crankshaft pin bushing are selected fitted and are not

interchangeable.

5. Check if the ring gaps are in proper positions (Figure 8).

FIGURE 8

WARNING: Read and understand supplement LV-474 before installing and operating the compressor.

CAP-600

7

• REBUILD KITS

AIR COOLED SINGLE STAGE MODELS

ES03 ES05

PART

NO. CONSISTS OF: PART

NO. CONSISTS OF:

1 70111-66140 Filter Element 1 70111-66140 Filter Element

2 70111-31030 Valve Disc 2 70112-31030 Valve Disc

1 70111-31070 Spring 1 70112-31070 Spring

1 70111-41070 Spring 1 70112-41070 Spring

1 70111-11461 Gasket 2 70112-61030 Comp. Ring

1 70111-11612 Head Gasket 1 70112-61050 Oil Ring

2 70111-61030 Comp. Ring 1 70112-11612 Head Gasket

1 70111-61050 Oil Ring 1 70112-51610 Crankcase Gasket

1 70111-57970 Bottom Cover Gasket 1 70112-57950 Front Cover Gasket

1 70111-57950 Front bearing cover gasket 1 70112-57960 Rear Cover Gasket

1 70111-57080 Front Oil Seal 1 70112-57080 Oil Seal

1 70111-57960 Rear Cover Gasket 12 92521-190800 Copper Washer

CF1299

10 92521-190600 Copper Washer

CF1237

1 70112-11461 Copper Gasket

ES06 ES10, ES10P ES20

PART

NO. CONSISTS OF: PART

NO. CONSISTS OF: PART

NO. CONSISTS OF:

2 70111-66140 Filter Element 2 70111-66140 Filter Element 3 70111-66140 Filter Element

4 70111-31030 Valve Disc 4 70112-31030 Disc 6 70112-31030 Disc

2 70111-31070 Spring 2 70112-31070 Spring 3 70112-31070 Spring

2 70111-41070 Spring 2 70112-41070 Spring 3 70112-41070 Spring

2 70111-11461 Gasket 4 70112-61030 Compression Ring 6 70112-61030 Compression Ring

2 70111-11612 Head Gasket 2 70112-61050 Oil Ring 3 70112-61050 Oil Ring

2 70121-51610 Crankcase Gasket 2 70112-11612 Head Gasket 3 70112-11612 Head Gasket

4 70111-61030 Comp. Ring 2 70112-51610 Crankcase Gasket 3 70112-51610 Crankcase Gasket

2 70111-61050 Oil Ring 1 70122-57950 Front Cover Gasket 1 70122-57950 Front Cover Gasket

1 70121-57950 Front Cover Gasket 1 70122-57960 Rear Cover Gasket 1 70122-57960 Rear Cover Gasket

1 70111-57960 Rear Cover Gasket 1 70122-57080 Front Oil Seal 1 70122-57080 Front Oil Seal

1 70121-57970 Bottom Cover Gasket 24 92521-190800 Copper Washer 26 92521-190800 Copper Washer

24 92521-190600 Copper Washer 2 70112-11461 Copper Gasket 3 70112-11461 Copper Gasket

CF1302

CF1238

CF1239

ES-30 ES-50 ES-100 ES-150 ES-150A

PART

NO. CONSISTS OF: PART

NO. CONSISTS OF: PART

NO. CONSISTS OF: PART

NO. CONSISTS OF: PART

NO. CONSISTS OF:

CF1246 REBUILD KIT INCLUDES: CF1252 PREVENTATIVE MAINTENANCE

KIT INCLUDES CF1252 PREVENTATIVE MAINTENANCE

KIT INCLUDES CF1252 PREVENTATIVE MAINTENANCE

KIT INCLUDES CF1252 PREVENTATIVE MAINTENANCE

KIT INCLUDES

2 70123-66140 Filter Kit

4 70123-31030 Disc 3 70123-66140 Filter Element 3 70123-66140 Filter Element 3 70123-66140 Filter Element 3 70123-66140 Filter Element

2 70123-31070 Spring

2 70123-41070 Spring CF1245 VALVE / GASKET MAINT. KIT INCLUDES CF1243 VALVE / GASKET MAINT. KIT INCLUDES: CF1241 VALVE / GASKET MAINT. KIT INCLUDES: CF1320 VALVE / GASKET MAINT. KIT INCLUDES:

4 70123-61030 Compression Ring

4 70123-61050 Oil Ring 6 70123-31030 Disc 6 70124-31030 Disc 6 70125-31030 Disc 3 70125-31030 Disc I / V

4 70123-11110 Seat Gasket 3 70123-31070 Spring 3 70124-31070 Spring 3 70125-31070 Spring 3 70125-31070 Spring

2 70123-11612 Head Gasket 3 70123-41070 Spring 3 70124-41070 Spring 9 70125-41074 Spring 9 701212A1-41075 Spring

2 70123-51610 Crankcase Gasket 6 70123-11110 Seat Gasket 6 70124-11110 Seat Gasket 6 70125-11110 Seat Gasket 6 70125-11110 Seat Gasket

1 70123-57950 Front Cover Gasket 3 70123-11612 Head Gasket 3 70124-11612 Head Gasket 3 70125-87510 Manifold Gasket 3 70125-41030 Disc O / V

1 70123-57960-01 Rear Cover Gasket 3 70125-11610 Head Gasket 3 70125-11612 Head Gasket

1 70123-57080 Front Oil Seal ** 70125-11612 Head Gasket

*2 70123-61081 Bushing

2 70123-61090 Set, Rod Bearing CF1244 REBUILD KIT INCLUDES: CF1242 REBUILD KIT INCLUDES: CF1244 REBUILD KIT INCLUDES: CF1244 REBUILD KIT INCLUDES:

26 92521-191000 Copper Washer

1 70123-57080 Front Oil Seal 1 70124-57950 Frt. Brg. Cvr. Gasket 1 70134-57080 Front Oil Seal 1 70134-57080 Front Oil Seal

6 70123-61030 Compr.Ring 6 70124-61030 Compr.Ring 6 70125-61030 Compression Ring 6 70125-61030 Compression Ring

6 70123-61050 Oil Ring 6 70124-61050 Oil Ring 6 70125-61050 Oil Ring 6 70125-61050 Oil Ring

*3 70123-61081 Bushing 3 70124-61080 Bushing *3 70125-61081 Bushing *3 70125-61081 Bushing

3 70123-61090 Set, Rod Bearing 6 70124-61090 Set, Rod Bearing 3 70125-61090 Set, Bearing 6 70125-61090 Set, Bearing

3 70123-51610 Crankcase Gasket 3 70124-51610 Crankcase Gasket *3 70135-51610 Crankcase Gasket *3 70135-51610 Crankcase Gasket

1 70123-57950

Frt. Brg. Cvr. Gasket 1 70134-57080 Front Oil Seal 1 70135-57950 Frt. Brg.Cvr Gasket 1 70135-57950 Frt. Brg.Cvr Gasket

1 70133-57960

Rear Brg. Cvr. Gasket 1 70134-57960

Rear Brg. Cvr. Gasket 1 70134-57960 Rear Brg.Cvr Gasket 1 70134-57960 Rear Brg.Cvr Gasket

34 92521-191000 Copper Washer 34 92521-191000 Copper Washer 24 92521-191000 Copper Washer 24 92521-191000 Copper Washer

* WARNING – THESE ITEMS INTERCHANGE WITH PARTS ON SERIAL #3020000 & HIGHER ONLY.

CONTACT FACTORY FOR EARLIER SERIES.

** USE WITH SERIAL #A311XXXX AND LATER.

70135-11610 REPLACES 70125-11610

CAP-600

8

• REBUILD KITS

AIR COOLED TWO STAGE MODELS

E-35

PART

NO. CONSISTS OF:

CF1306 PREVENTATIVE MAINTENANCE

KIT INCLUDES:

1 70152-66141 Element

CF1307 VALVE/GASKET MAINT KIT

INCLUDES:

4 70152-31030 Disc

2 70152-32030 Disc

4 70152-31070 Spring

2 70152-32070 Spring

1 70152-11612 Head Gasket

1 70152-31120 Seat Gasket

1 70152-11622 Seat Gasket

CF1308 REBUILD KIT INCLUDES:

1 70152-51610 Case Gasket

1 70152-57960 Rear Cover Gasket

2 70152-61030 Comp. Ring

1 70152-61050 Oil Ring

1 70152-61080 Bushing (L.P.)

1 70152-62080 Bushing (H.P.)

2 70152-61090 Rod Bearing Set

3 70152-62030 Compression Ring

1 70152-62050 Oil Ring

1 70152-57950 Front Cover Gasket

1 70127-57080 Front Oil Seal

6 92521-190800 Copper Washer

E-11 E-23

PART

NO. CONSISTS OF: PART

NO. CONSISTS OF:

CF1250 1 70111-66140 Filter Element CF1251 2 70111-66140 Filter Element

2 70112-31030 Disc 4 70112-31030 Disc

2 70162-32030 Disc 2 70111-31030 Disc

1 70112-31070 Spring 2 70112-31070 Spring

1 70162-42070 Spring 2 70112-41070 Spring

1 70112-41070 Spring 1 70172-32070 Spring

1 70162-32070 Spring 1 70172-42070 Spring

2 70112-61030 Compression Ring 4 70112-61030 Compression Ring

1 70112-61050 Oil Ring 2 70112-61050 Oil Ring

2 70162-62030 Compression Ring 2 70111-61030 Compression Ring

2 70162-62050 Oil Ring 2 70111-61050 Oil Ring

1 70112-11612 Head Gasket (1st) 2 70112-11612 Head Gasket (1st)

1 70162-12610 Head Gasket (2nd) 1 70111-11612 Head Gasket (2nd)

2 70112-51610 Crankcase Gasket 3 70112-51610 Crankcase Gasket

1 70122-57950 Front Cover Gasket 1 70122-57950 Front Cover Gasket

1 70122-57960 Rear Cover Gasket 1 70122-57960 Rear Cover Gasket

1 70122-57080 Front Oil Seal 1 70122-57080 Front Oil Seal

24 92521-190800 Copper Washer 32 92521-190800 Copper Washer

1 70112-11461 Copper Gasket 1 70111-11461 Copper Gasket

2 70112-11461 Copper Gasket

E-57 E-50 E-71 E-15

PART NO. CONSISTS OF: PART

NO. CONSISTS OF: PART

NO. CONSISTS OF: PART

NO. CONSISTS OF:

CF1291 PREVENTATIVE MAINTENANCE KIT

INCLUDES CF1315 PREVENTATIVE MAINTENANCE

KIT INCLUDES: CF1315 PREVENTATIVE MAINTENANCE

KIT INCLUDES: CF1315 PREVENTATIVE MAINTENANCE

KIT INCLUDES:

1 70153-66142 Element 2 70123-66140 Element 2 70123-66140 Element 2 70123-66140 Element

CF1292 VALVE/GASKET MAINT KIT

INCLUDES: CF1253 VALVE/GASKET MAINT KIT

INCLUDES: CF1255 VALVE/GASKET MAINT KIT

INCLUDES: CF1257 VALVE/GASKET MAINT KIT

INCLUDES:

4 70153-31032 Disc 6 70123-31030 Disc 4 70124-31030 Disc 4 70125-31030 Disc

2 70153-32032 Disc 3 70123-31070 Spring 2 70123-31030 Disc 2 70175-42030 Disc

4 70153-31072 Spring 3 70123-41070 Spring 2 70124-31070 Spring 2 70125-31070 Spring

2 70153-32072 Spring 6 70123-11110 Seat Gasket 1 70123-31070 Spring 1 70124-31070 Spring

1 70153-31120 Head Gasket 3 70123-11612 Head Gasket 2 70124-41070 Spring 6 70125-41070 Spring

1 70153-11612 Seat Gasket 1 70123-41070 Spring 1 70124-41072 Spring

1 70153-11622 Seat Gasket 4 70124-11110 Seat Gasket 4 70125-11110 Seat Gasket

2 70123-11110 Seat Gasket 2 70124-11110 Seat Gasket

2 70124-11612 Head Gasket 4 70125-87510 Manifold Gasket

1 70123-11612 Head Gasket 2 70125-11610 Head Gasket

1 70124-11612 Head Gasket

** 70135-11610 Head Gasket

CF1293 REBUILD KIT INCLUDES: CF1254 REBUILD KIT INCLUDES: CF1256 REBUILD KIT INCLUDES: CF1258 REBUILD KIT INCLUDES:

1 70153-57951 Front Bearing Gasket 1 70123-57950 Front Bearing Gasket 1 70124-57950 Front Bearing Gasket 4 70125-61030 Compression Ring

2 70124-61030 Compression Ring 4 70123-61030 Compression Ring 4 70124-61030 Compression Ring 4 70125-61050 Oil Ring

2 70124-61050 Oil Ring 4 70123-61050 Oil Rings 4 70124-61050 Oil Ring 3 70124-61030 Compression Ring

3 70153-62030 Compression Ring 3 70112-61030 Compression Ring 3 70123-61030 Compression Ring 2 70124-61050 Oil Ring

1 70153-62050 Oil Ring 1 70112-61050 Oil Ring 2 70123-61050 Oil Ring 2 70125-61081 Bushing

1 70153-61081 Bushing (L.P.) 2 70123-61081 Bushing 2 70124-61080 Bushing 3 70125-61090 Rod Bearing (2 Halves)

1 70153-62081 Bushing (H.P.) 1 93503TA1725 Needle Bearing 1 70174-62081 Bushing 3 70135-51610 Gasket

4 70153-61090 Rod Bearing (Halves) 6 70123-61090 Rod Bearing (Halves) 3 70124-51610 Gasket 1 70134-57080 Oil Seal

1 70153-51611 Case Gasket 3 70123-51610 Crankcase Gasket 1 70134-57080 Oil Seal 1 70135-57950 Front Bearing Gasket

1 70123-57080 Oil Seat 1 70123-57080 Oil Seal 6 70124-61090 Bearing (Halves) 1 70134-57960 Rear Bearing Gasket

1 70153-57961 Rear Bearing Gasket 1 70133-57960 Rear Bearing Gasket 1 70134-57960 Rear Bearing Gasket 24 92521-191200 Copper Washer

26 92521-191000 Copper Washer 34 92521-191000 Copper Washer 34 92521-191000 Copper Washer 1 93503-NK28/30 Needle Bearing ***

1 70173-62080 Bushing 1 70175-62080 Bushing ****

* WARNING – THESE ITEMS INTERCHANGE WITH PARTS ON SERIAL #3020000 & HIGHER ONLY.

CONTACT FACTORY FOR EARLIER SERIES.

** USE WITH SERIAL #A311XXXX AND LATER.

70135-11610 REPLACES 70125-11610

*** USE WITH SERIAL #A409XXXX AND LATER

**** USE FOR UNITS PRIOR TO SERIAL #A409XXXX

CAP-600

9

RING SETS & GASKET SETS

SINGLE STAGE

MODEL PART NO. DESCRIPTION QUANTITY

REQ’D

ES03 CF1297

CF1298 Ring set

Gasket set 1

1

ES05 CF1259

CF1276 Ring set

Gasket set 1

1

ES06 CF1300

CF1301 Ring set

Gasket set 2

1

ES10 CF1260

CF1277 Ring set

Gasket set 2

1

ES20 CF1261

CF1278 Ring set

Gasket set 3

1

ES30 CF1262

CF1279 Ring set

Gasket set 2

1

ES50 CF1263

CF1280 Ring set

Gasket set 3

1

ES100 CF1264

CF1281 Ring set

Gasket set 3

1

ES150 &

ES150A

CF1265

CF1282

*CF1311

Ring set

Gasket set

*Gasket set

3

1

1

TWO-STAGE

MODEL PART NO. DESCRIPTION QUANTITY

REQ’D

E11 CF1266

CF1267

CF1283

Ring set (LP)

Ring set (HP)

Gasket set

1

1

1

E23 CF1268

CF1269

CF1284

Ring set (LP)

Ring set (HP)

Gasket set

2

1

1

E35 CF1303

CF1304

CF1305

Ring set(LP)

Ring set(HP)

Gasket set

1

1

1

E50 CF1270

CF1271

CF1285

Ring set(LP)

Ring set(HP)

Gasket set

2

1

1

E57 CF1288

CF1289

CF1290

Ring set(LP)

Ring set(HP)

Gasket set

1

1

1

E71 CF1272

CF1273

CF1286

Ring set(LP)

Ring set(HP)

Gasket set

2

1

1

E15

CF1274

CF1275

CF1287

*CF1313

Ring set(LP)

Ring set(HP)

Gasket set

*Gasket set

2

1

1

1

* USE WITH SERIAL #A311XXXX AND LATER

CAP-600

10

MODEL ES-03

AIR COOLED, SINGLE STAGE, SINGLE CYLINDER

Description QTY PART NO.

VALVES

1. Inlet & Outlet Valve Plate 2 70111-31030

2. Inlet Valve Spring 1 70111-31070

3. Inlet Valve Receiver 1 70111-31020

4. Inlet Valve Snap Ring 1 93610-130225

5. Outlet Valve Spring 1 70111-41070

6. Outlet Valve Push Cover Gasket 1 70111-11461

7. Outlet Valve Push Cover 1 70111-11450

8. Manual Unloader Assembly 1 70111-11300

9.

CYLINDERS

9A. Cylinder Head Assembly (Includes Valves) 1 70111-11000-4024

9B. Cylinder Head (Bare Casting) 1 70111-11010

10. Cylinder Head Bolt (Not Shown) 4 (Hardware Item)

11. Cylinder Head Gasket 1 70111-11612

12. Cylinder & Crankcase 1 70111-57010-4024

13. Compression Ring 2 70111-61030

14. Oil Control Ring 1 70111-61050

15. Piston 1 70111-61011

16. Piston Pin 1 70111-61120

17. Piston Pin Snap Ring 2 70111-61070

18. Connecting Rod Assembly 1 70111-61200

19. Connecting Rod Bolt 2 (furnished on conn.

Rod only)

20. Oil Splash Dipper 1 70111-61282

21. Oil Splash Dipper Bolt 1 91507-2304010

22. Oil Splash Dipper Bolt Washer (Not Shown) 1 92522-130400

Description QTY PART NO.

CRANKCASE AND CRANK ASSEMBLY

23. Crankshaft 1 70111-56010

24. Front Bearing Cover 1 70111-57030

25. Front Bearing Cover Gasket 1 70111-57950

26. Front Cover Bolts (Not Shown) 4 91501-1306016

27. Front Bearing #6203 1 93501-6203

28. Rear Bearing Cover 1 70111-57060

29. Rear Bearing Cover Gasket 1 70111-57960

30. Rear Bearing #6201 1 93501-6201

31. Rear Bearing Cover Bolts (Not Shown) 3 93501-1306016

32. Front Oil Seal 1 70111-57080

33. Compressor Pulley 1 70111-76010

34. Compressor Pulley Thrust Washer 1 70111-76210

35. Compressor Pulley Thrust Bolt 1 91501-1306020

36. Crankcase Bottom Cover (Not Shown) 1 70111-57220

37. Crankcase Bottom Cover Gasket (Not

Shown) 1 70111-57970

38. Compressor Pulley Pin NA (Not Required)

39. Oil Level Gauge And Cover 1 70111-57700

40. Gauge Cover Seal 1 70111-57730

41. Crankcase Oil Plug (1/4” PT) 1 90112-100202

42. Breather Assembly 1 70191-57600-4024

AIR STRAINER ELEMENT

43. Air Strainer Assembly 1 70111-66001

44. Air Strainer Element (Not Shown) 1 70111-66140

CRANKCASE AND CRANK ASSEMBLY

CAP-600

11

MODEL ES-06

AIR COOLED, SINGLE STAGE, SINGLE CYLINDER

* START S/N AS 4030001

DESCRIPTION QTY PART NO. DESCRIPTION QTY PART NO.

VALVES 28 Front Bearing Cover Gasket 1 70121-57950

1. Inlet And Outlet Valve Plate 4 70111-31030 29 Front Bearing Cover Bolt 4 91501-1306016

2. Inlet Valve Spring 2 70111-31070 30 Front Bearing #6204 1 93501-6204

3. Inlet Valve Receiver 2 70111-31020 32 Rear Bearing Cover 1 70111-57060

4. Inlet Valve Snap Ring 2 93610-130225 33 Rear Bearing Cover Gasket 1 70111-57960

5. Outlet Valve Spring 2 70111-41070 34 Rear Bearing Cover Bolt (Not Shown) 3 91501-1306016

6. Outlet Valve Push Cover Gasket 2 70111-11461 35 Rear Bearing #6203 1 93501-6203

7. Outlet Valve Push Cover 2 70111-11450 36 Crankcase Bottom Cover (Not Shown) 1 70121-57220

37 Crankcase Bottom Cover Bolt (Not Shown) 1 70121-57970

CYLINDERS, CRANKCASE AND CRANK ASSEMBLY 38 Crankcase Bottom Cover Washer (Not Shown) 4 (Hardware Item)

8a. Cylinder Head Assy. (Includes Valves) 2 70111-11000-4024 39 Front & Rear Cover Bolt Washer (Not Shown) 10 92521-190600

8b. Cylinder Head (Bare Casting) 2 70111-11010 40 Compressor Pulley Pin 1 70112-56060

9. Cylinder Head Gasket 2 70111-11612 41 Compressor Pulley 1 70121-76011

10 Cylinder Head Bolt 8 91501-1306055 42 Compressor Pulley Thrust Washer 1 70112-76210

11 Cylinder 2 70121-51010 43 Compressor Pulley Thrust Bolt 1 91501-1306025

12 Cylinder To Case Gasket 2 70121-51610 44 Oil Level Gauge & Gauge Cover 1 70111-57700

13 Cylinder To Case Bolt (Not Shown) 8 91501-1306016 *44A Oil Level Gauge Assy 1 70704-57700

14 Cylinder To Case Bolt Washer (Not Shown) 16 92521-190600 45 Oil Level Gauge Cover Seal 1 70111-57730

15 Compression Ring 4 70111-61030 *45A Oil Level Gauge “O” Ring 1 93602-8126026

16 Oil Control Ring 2 70111-61050 46 Crankcase Oil Plug (1/4” NPT) 1 90112-100202

17 Piston 2 70111-61011 47 Breather Assembly 1 CCC1357

18 Piston Pin 2 70111-61120 UNLOADERS(* Indicates Not Included On Basic Units)

19 Piston Pin Snap Ring 4 70111-61070 48 Auto – Unloader Assembly 2 70112-11201

20 Connecting Rod Assembly 2 70111-61200 49 Unloading Elbow* (Includes Nut & Sleeve) 1 VA786

21 Connecting Rod Bolt 4 (Furnished On

Conn, Rod Only) 50 Unloading Tee* (Includes Nut & Sleeve) 1 VA787

22 Oil Splash Dipper 2 70121-61282 AIR STRAINER ASSEMBLY & DISCHARGE PIPING

23 Oil Splash Dipper Bolt 2 91507-2304010 51 Air Strainer Assembly 2 70111-66001

24 Oil Splash Dipper Lockwasher (Not Shown) 2 92522-130400 52 Air Strainer Element (Not Shown) 2 70111-66140

25 Crankshaft 1 70121-56010 53 Compressor Body Discharge Pipe Assembly 1 70121-87100

26 Crankcase 1 70121-57010-4024 54 Outlet Pipe Elbow 1 70121-87010

27 Front Bearing Cover 1 70121-57030 55 Outlet Pipe Tee 1 70121-87020

56 Outlet Pipe Tee Nut 1 79922-130404

CAP-600

12

AIR COOLED, SINGLE STAGE MODELS

ES-05, ES-10 & ES-20

CAP-600

13

MAIN PARTS LISTING FOR

SINGLE STAGE MODELS

ES-05, ES-10 & ES-20

VALVES QTY

REQ’D MODEL ES05 QTY

REQ’D MODEL ES10 QTY

REQ’D MODEL ES20

1. Inlet And Outlet Valve Plate 2 70112-31030 4 70112-31030 6 70112-31030

2. Inlet Valve Spring 1 70112-31070 2 70112-31070 3 70112-31070

3. Inlet Valve Receiver 1 70112-31020 2 70112-31020 3 70112-31020

4. Inlet Valve Snap Ring 1 93610-130232 2 93610-130232 3 93610-130232

5. Outlet Valve Spring 1 70112-41070 2 70112-41070 3 70112-41070

6. Outlet Valve Push Cover Gasket 1 70112-11461 2 70112-11461 3 70112-11461

7. Outlet Valve Push Cover 1 70112-11450

2 70112-11450

3 70112-11450

CYLINDER AND CYLINDER HEADS

16A. Cylinder Head Assembly 1 70112-11000-4024 2 70112-11000-4024 3 70112-11000-4024

16B. Cylinder Head 1 70112-11010 2 70112-11010 3 70112-11010

17. Cylinder & Head Gasket 1 70112-11612 2 70112-11612 3 70112-11612

18. Cylinder 1 70112-51010 2 70112-51010 3 70112-51010

19. Cylinder And Case Gasket 1 70112-51610 2 70112-51610 3 70112-51610

20. Compression Ring 2 70112-61030 4 70112-61030 6 70112-61030

21. Oil Control Ring 1 70112-61050 2 70112-61050 3 70112-61050

22. Piston 1 70112-61011 2 70112-61011 3 70112-61011

23. Piston Pin 1 70112-61120 2 70112-61120 3 70112-61120

24. Piston Pin Snap Ring 2 70112-61070 4 70112-61070 6 70112-61070

25. Connecting Rod Assembly 1 70112-61200-1 2 70112-61200-1 3 70112-61200-1

26. Connecting Rod Bolt 1 70112-61250 4 70112-61250 6 70112-61250

27. Oil Splash Dipper 1 70111-61282 2 70122-61282 2 70122-61282

27A. Oil Splash Dipper 1 70132-61290

28. Oil Splash Dipper Bolts 1 91507-2304010 2 91507-2304010 3 91507-2304010

29. Cylinder Head Bolt 4 (Hardware Item)

8 (Hardware Item)

12 (Hardware Item)

CRANK ASSEMBLY

39. Crankcase 1 70112-57010-4024 1 70122-57010-4024 1 70132-57010-4024

40. Crankshaft 1 70112-56010 1 70122-56010 1 70132-56010

41. Front Bearing Cover 1 70112-57030 1 70122-57030 1 70122-57030

42. Front Bearing Cover Gasket 1 70112-57950 1 70122-57950 1 70122-57950

43. Rear Bearing Cover 1 70112-57060 1 70122-57060 1 70122-57060

44. Rear Bearing Cover Gasket 1 70112-57960 1 70122-57960 1 70122-57960

45A. Bearing – Front 1 93501-6205 1 93501-6205 1 93501-6205

45B. Bearing – Rear 1 93501-6204 1 93501-6204 1 93501-6204

46. Front Oil Seal 1 70112-57080 1 70122-57080 1 70122-57080

47. V-Pulley Pin 1 70112-56060 1 70112-56060 1 70112-56060

48. Compressor Pulley 1 70112-76010 1 70122-76011 1 70122-76011

49. Compressor Pulley Thrust Washer 1 70112-76210 1 70112-76210 1 70112-76210

50. Compressor Pulley Thrust Bolt 1 91501-1308025 1 91501-1308025 1 91501-1308025

51. Breather Assembly 1 CCC1375 1 CCC1375 1 CCC1375

52. Oil Gauge & Gauge Cover 1 70111-57700 1 70111-57700 1 70111-57700

٭52 A Oil Level Gauge Assembly - 1 70704-57700 1 70704-57700

53. Gauge Cover Seal 1 70111-57730 1 70111-57730 1 70111-57730

٭53 A Oil Level Gauge “O” Ring - 1 93602-8126026 1 93602-8126026

54. Crankcase Oil Plug 1 90112-100202

1 90112-100202

1 90112-100202

54A. Oil fill cap - - 1 70101-57190-4010

54B. “O” Ring - - 1 93601-810016

UNLOADERS

55. Auto – Unloader Assembly 1 70112-11201 2 70112-11201 3 70112-11201

56. Auto – Unloader Spring 1 70112-11230 2 70112-11230 3 70112-11230

57. Auto – Unloader Piston 1 70112-11221 2 70112-11221 3 70112-11221

58. O-Ring (Unloader) 1 93601-810004

2 93601-810004

3 93601-810004

AIR STRAINER

61. Air Strainer Element 1 70111-66140 2 70111-66140 3 70111-66140

62. Air Strainer Assembly 1 70111-66001 2 70111-66001 3 70111-66001

63. Discharge Piping Assembly 1 (Not Required) 2 70122-87100 2 70132-87100

64. Outlet Pipe Joint A - 1 70122-87010 1 70122-87010

65. Outlet Pipe Joint B - 1 70122-87020 1 70132-87020

66. Outlet Pipe Joint C -

-

1 70132-87030

• ES10, START S/N AS 4030043

• ES20, START S/N AS 4030061

CAP-600

AIR COOLED SINGLE STAGE

MODELS ES-30, ES-50, ES-100

14

Description Qty.

Req. MODEL

ES30 Qty.

Req. MODEL

ES50 Qty.

Req. MODEL

ES100

Inlet Valve Assembly, 1st Stage 2 70123-31000 3 70123-31000 3 70124-31000

Outlet Valve Assembly, 1st Stage 2 70123-41000 3 70123-41000 3 70124-41000

Air Strainer Assembly 2 70123-66000 3 70123-66000 3 70123-66000

VALVE ASSEMBLIES

Breather Assembly 1 70103-57600-4024 1 70103-57600-4024 1 70124-57600

MAIN PARTS LISTING FOR MODELS

ES-30, ES-50, ES-100

Item

No. Description Qty.

Req. MODEL

ES30 Qty.

Req. MODEL

ES50 Qty.

Req. MODEL

ES100

1. Inlet Valve Seat 2 70123-31010 3 70123-31010 3 70124-31010

2. Inlet Valve Receiver 2 70123-31020 3 70123-31020 3 70124-31020

3. Inlet & Outlet Valve Plate 4 70123-31030 6 70123-31030 6 70124-31030

4. Inlet Valve Spring 2 70123-31070 3 70123-31070 3 70124-31070

5. Inlet Valve Unloading Fork Guide 2 70123-31090 3 70123-31090 3 70124-31090

6. Unloading Spring 2 70123-11230 3 70123-11230 3 70124-11230

VALVE &

UNLOADERS

7A. Valve Gasket 4 70123-11110 6 70123-11110 6 70124-11110

CAP-600

AIR COOLED SINGLE STAGE

MODELS ES-30, ES-50, ES-100

14A

Description Qty.

Req. MODEL

ES30A Qty.

Req. MODEL

ES50A Qty. Req. MODEL

ES100A

Inlet Valve Assembly, 1st Stage 2 701208A1-31000 3 701208A1-31000 3 701210A1-31000

Outlet Valve Assembly, 1st Stage 2 701208A-41000 3 701208A1-41000 3 701210A1-41000

Air Strainer Assembly 2 701208A1-66000 3 701208A1-66000 3 701312A1-66000

VALVE ASSEMBLIES

Breather Assembly 1 701105A1-57600 1 701105A1-57600 1 701210A1-57601

MAIN PARTS LISTING FOR MODELS

ES-30A, ES-50A, ES-100A

Item

No. Description Qty.

Req. MODEL

ES30A Qty.

Req. MODEL

ES50A Qty. Req. MODEL

ES100A

1. Inlet Valve Seat 2 701208A1-31010 3 701208A1-31010 3 701210A1-31010

2. Inlet Valve Receiver 2 701208A1-31020 3 701208A1-31020 3 701210A1-31020

3. Inlet & Outlet Valve Plate 2 701208A1-31030 6 701208A1-31030 6 501210A1-31030

4. Inlet Valve Spring 2 701208A1-31070 3 701208A1-31070 3 701210A1-31070

5. Inlet Valve Unloading Fork Guide 2 701208A1-31090 3 701208A1-31090 3 701210A1-31090

6. Unloading Spring 2 701208A1-11230 3 701208A1-11230 3 701210A1-11230

VALVE &

UNLOADERS

7A. Valve Gasket 4 701208A1-11110 6 701208A1-11110 6 701210A1-11110

CAP-600

15

MAIN PARTS LISTING FOR MODELS

ES-30, ES-30A, ES-50 & ES-100 (Continued)

Qty.

Req. MODEL

ES30 Qty.

Req. MODEL

ES50 Qty.

Req. MODEL

ES100

7B Inlet Valve Unloading Fork 2 70123-31080 3 70123-31080 3 70124-31080

8. Locknut 2 92518-230800 3 92518-230800 3 92518-230800

10. Outlet Valve Seat 2 70123-41011 3 70123-41011 3 70124-41011

11. Outlet Valve Receiver 2 70123-41020 3 70123-41020 3 70124-41020

12. Outlet Valve Spring 2 70123-41070 3 70123-41070 3 70124-41070

13. Outlet Valve Bolt 2 70123-41810 3 70123-41810 3 70124-41810

14. Nut (Outlet Valve) 4 92502-130800 6 92502-130800 6 92502-130800

15. Inlet Valve Push Cover, 1st Stage 2 70123-11150 3 70123-11150 3 70124-11150

16. O – Ring G 40 2 93602-810040 3 93602-810040 3 93602-810055

17. Viton O – Ring G 40 (Outlet Valve) 2 93602-870040 3 93602-870040 3 93602-870055

18. Unloading Piston, 1st Stage 2 70123-11220 3 70123-11220 3 70124-11220

19. O – Ring P 20 2 93601-810020 3 93601-810020 3 93601-810021

VALVES & UNLOADERS (Cont’d)

20. Outlet Valve Push Cover, 1st Stage 2 70123-11450 3 70123-11450 3 70124-11450

21A. Cylinder Head Assembly 2 70123-11000 3 70123-11000 -

21. Cylinder Head (1st) 2 70123-11010 3 70123-11010 3 70124-11010

22. Cylinder & Head Gasket, 1st Stage 2 70123-11612 3 70123-11612 3 70124-11612

23. Cylinder (1st) 2 70123-51012 3 70123-51012 3 70124-51011

23A. S/N 3020000 THRU A311XXXX 2 70123-51011 3 70123-51011 3 70124-51011

24. Cylinder & Case Gasket 2 70123-51610 3 70123-51610 3 70124-51610

25. Compression Ring (1st) 4 70123-61030 6 70123-61030 6 70124-61030

26. Oil Control Ring (1st) 4 70123-61050 6 70123-61050 6 70124-61050

27. Piston (1st) 2 70123-61011 3 70123-61011 3 70124-61011-1

27A. S/N 3020000 & later use 2 70123-61011 3 70123-61011 3 70124-61011

28. Piston Pin Snap Ring 4 70123-61070 6 70123-61070 6 70124-61070

29. Piston Pin (1st) 2 70123-61120 3 70123-61120 3 70124-61120

30. Connecting Rod Piston Pin Bushing (1st) 2 70123-61081 3 70123-61081 3 70124-61080

31. Connecting Rod Assembly, 1st Stage 2 70123-61200 3 70123-61200 3 70124-61201

31A. S/N 3020000 & later use 2 70123-61201 3 70123-61201 3 70124-61201

32. Connecting Rod Crank Pin Metal 4 70123-61090 6 70123-61090 6 70124-61090

33. Connecting Rod Bolt 4 70123-61250 6 70123-61250 6 70125-61250

33A. Oil Splash Dipper H.P. - 1 70122-61290 1 70134-62290

34. Oil Splash Dipper 2 70122-61282 2 70122-61282 2 70134-61281

CYLINDERS

35. Oil Splash Dipper Bolt 2 91507-2304012 3 91507-2304012 3 91507-2305016

42. Crankshaft 1 70123-56010 1 70133-56011 1 70134-56010

43. Counterweight - - 2 70134-56030

44. Lockwasher - - 2 70124-56830

45. Bolt - - 2 70124-56810

46. Crankcase 1 70123-57010-4024 1

70133-57010-

4024 1 70134-57010-4024

47. Front Bearing Cover 1 70123-57030 1 70133-57030 1 70134-57031

48. Front Bearing Cover Gasket 1 70123-57950 1 70123-57950 1 70124-57950

49. Rear Bearing Cover 1 70123-57061 1 70133-57060 1 70134-57061

49A. S/N 3020000 & later use 1 70123-57061 1 70133-57061 1 70134-57061

50. Rear Bearing Cover Gasket 1 70123-57960-01 1 70133-57960 1 70134-57960

51. Front Bearing 1 93501-6206 1 93501-6206 1 93502-32210

52. Rear Bearing 1 93501-6206 1 93501-6206 1 93502-32210

53. Front Oil Seal 1 70123-57080 1 70123-57080 1 70134-57080

54. V – Pulley Pin 1 70123-56061 1 70123-56061 1 70134-56060

55A. Compressor Fan 1 (Not Required) 1 (Not Required) 1 70124-76310

55B. Compressor Pulley 1 70123-76010 1 70133-76010 1 70134-76011

56. Compressor Pulley Washer 1 70123-76210 1 70124-76210 1 70124-76210

57. Compressor Pulley Set Bolt 1 91501-1312030 1 91501-1312030 1 91501-1312040

58. Gauge Cover 1 70111-57700 1 70111-57700 1 70124-57700

٭58 A. Oil Level Gauge Assy. 1 70704-57700 1 70704-57700 -

59. Gauge Cover Seal 1 70111-57730 1 70111-57730 1 70124-57730

٭59 A. Oil Level Gauge “O” Ring 1 93602-8126026 1 93602-8126026 -

60. Crankcase Oil Cap 1 CCC1257 1 CCC1257 1 CCC1257

61. Crankcase Oil Plug 1 90112-100404 1 90112-100404 1 90112-100404

67. Air Strainer Filter 2 70123-66140 3 70123-66140 3 70123-66140

69. Outlet Pipe Joint B 1 70123-87020 1 70133-87020 1 70134-87020

70. Compressor Body Discharge Piping Assy. 1 70123-87100 2 70133-87101 2 70134-87100

70A. S/N 3020000 & Later Use 1 70123-87101 2 70133-87101 2 70134-87101

CRANKCASE & CRANK ASSEMBLY

71. Outlet Pipe Joint A 1 70123-87010 1 70123-87010 1 70124-87010

73. Outlet Pipe Joint C - 1 70133-87030 1 70134-87030

74. Gasket (Manifold) - - -

75. Breather Assembly 1 CCC1375 1 CCC1375 1 CCC1375

* ES30, START S/N AS4030091

* ES50, START S/N AS4030115

CAP-600

15A

MAIN PARTS LISTING FOR MODELS

ES-30A, ES-50A & ES-100A (Continued)

Qty.

Req. MODEL

ES30A Qty.

Req. MODEL

ES50A Qty.

Req. MODEL

ES100A

7B Inlet Valve Unloading Fork 2 701208A1-31080 3 701208A1-31080 3 70210A1-31080

8. Locknut 2

9251313-150800-532 3 9251313-150800-532 3 9251313-151000-532

10. Outlet Valve Seat 2 701208A1-41011 3 701208A1-41011 3 701210A1-41011

11. Outlet Valve Receiver 2 701208A1-41020 3 701208A1-41020 3 701210A1-41020

12. Outlet Valve Spring 2 701208A1-41070 3 701208A1-41070 3 701210A1-41070

13. Outlet Valve Bolt 2 701208A1-41810 3 701208A1-41810 3 9152613-1110050-5608

14. Nut (Outlet Valve) 4 9250113-150800-532 6 9250113-150800-532 6 9250113-121000-532

15. Inlet Valve Push Cover, 1st Stage 2 701208A1-11150 3 701208A1-11150 3 701210A1-11150

16. O – Ring G 40 (G55 ES100) 2 9360281-310394 3 9360281-310394 3 9360281-310544

17. Viton O – Ring G 40 (Outlet Valve) 2 9360287-310394 3 9630287-310394 3 9360287-310544

18. Unloading Piston, 1st Stage 2 701208A1-11220 3 701208A1-11220 3 701210A1-11220

19. O – Ring P 20 (P21 ES100) 2 9360181-240198 3 9360181-240198 3 9360187-240208

VALVES & UNLOADERS (Cont’d)

20. Outlet Valve Push Cover, 1st Stage 2 701208A1-11450 3 701208A1-11450 3 701210A1-11450

21A. Cylinder Head Assembly 2 70123-11000 3 70123-11000 -

21. Cylinder Head (1st) 2 701208A2-11010 3 701208A2-11010 3 701210A2-11010

22. Cylinder & Head Gasket, 1st Stage 2 701208A1-11020 3 701208A1-11020 3 701210A1-11020

23. Cylinder (1st) 2 701208A2-51010 3 701208A2-51010 3 701210A2-51010

23A. S/N 3020000 THRU A311XXXX 2 701208A1-51010 3 701208A2-51010 3 701210A2-51010

24. Cylinder & Case Gasket 2 701208A1-51030 3 701208A1-51030 3 701210A1-51030

25. Compression Ring (1st) 4 701208A1-61030 6 701208A1-61030 6 701210A1-61030

26. Oil Control Ring (1st) 4 701208A1-61050 6 701208A1-61050 6 701210A1-61050

27. Piston (1st) 2 701208A1-61012 3 701208A1-61012 3 701210A1-61011

27A. S/N 3020000 & later use 2 70123-61011 3 70123-61011 3 701210A1-61011

28. Piston Pin Snap Ring 4 701208A1-61070 6 701208A1-61070 6 701210A1-61070

29. Piston Pin (1st) 2 701208A1-61120 3 701208A1-61120 6 701210A1-61120

30. Connecting Rod Piston Pin Bushing (1st) 2 70123-61081 3 70123-61081 3 70124-61080

31. Connecting Rod Assembly, 1st Stage 2 701208A1-61201 3 701208A1-61201 3 701210A1-61201

31A. S/N 3020000 & later use 2 701208A1-61201 3 701208A1-61201 3 701210A1-61201

32. Connecting Rod Crank Pin Metal 4 70123-61090 6 70123-61090 6 70124-61090

33. Connecting Rod Bolt 4 70123-61250 6 70123-61250 6 70125-61250

33A. Oil Splash Dipper H.P. - 1 70130FA1-61290 1 701310A1-61290

34. Oil Splash Dipper 2 70120FA1-61282 2 70120FA1-61282 2 701310A1-61281

CYLINDERS

35. Oil Splash Dipper Bolt 2 9151313-1104012-5602 3 9151313-1104012-5602 3 9151313-1105016-5602

42. Crankshaft 1 701208A1-56011 1 701308A1-56011 1 701310A1-56010

43. Counterweight - - 2 701310A1-56030

44. Lockwasher - - 2 701210A1-56830

45. Bolt - - 2 701210A1-56810

46. Crankcase 1 701208A2-57010 1 701308A2-57010 1 701310A2-57010

47. Front Bearing Cover 1 701208A1-57030 1 701308A1-57030 1 701310A1-57031

48. Front Bearing Cover Gasket 1 701208A1-57040 1 701208A1-57040 1 701210A1-57040

49. Rear Bearing Cover 1 701208A1-57061 1 701308A1-57061 1 701310A1-57061

49A. S/N 3020000 & later use 1 701208A1-57061 1 701308A1-57061 1 701310A1-57061

50. Rear Bearing Cover Gasket 1 701208A1-57070 1 701308A1-57070 1 701310A1-57070

51. Front Bearing 1 9350104-6206 1 9360112-6306 1 9354501-32210

52. Rear Bearing 1 9350104-6206 1 9360112-6306 1 9354501-32210

53. Front Oil Seal 1 701208A1-57080 1 701208A1-57080 1 701310A1-57080

54. V – Pulley Pin 1 701208A1-56061 1 701208A1-56061 1 701310A1-56060

55A. Compressor Fan 1 (Not Required) 1 (Not Required) 1 70121071-76311

55B. Compressor Pulley 1 701208A1-76010 1 701308A1-76010 1 701310A1-76011

56. Compressor Pulley Washer 1 701208A1-76210 1 70124-76210 1 701210A1-76210

57. Compressor Pulley Set Bolt 1 9150113-1112030-5608 1 9150113-1112030-5608 1 9150113-1112040-5608

58. Gauge Cover 1 70111-57700 1 70111-57700 1 701210A1-57740

٭58 A. Oil Level Gauge Assy. 1 70A109B1-57701 1 70A109B1-57701 1 701210A1-57700

59. Gauge Cover Seal 1 70111-57730 1 70111-57730 1 701210A1-57730

٭59 A. Oil Level Gauge “O” Ring 1 9360281-260265 1 9360281-260265 -

60. Crankcase Oil Cap 1 CCC1257 1 CCC1257 1 CCC1257

61. Crankcase Oil Plug 1 9156310-400800 1 9156310-400800 1 9156310-400800

67. Air Strainer Filter 2 701208A1-66140 3 701208A-66110 3 701208A1-66110

69. Outlet Pipe Joint B 1 70123-87020 1 70133-87020 1 70134-87020

70. Compressor Body Discharge Piping Assy. 1 70123-87100 2 701308A1-87101 2 70134-87100

70A. S/N 3020000 & Later Use 1 701208A1-87101 2 701308A1-87101 2 701310A1-87101

71. Outlet Pipe Joint A 1 701208A1-87011 1 70123-87010 1 70124-87010

73. Outlet Pipe Joint C - 1 70133-87030 1 70134-87030

74. Gasket (Manifold) - - -

CRANKCASE & CRANK ASSEMBLY

75. Breather Assembly 1 CCC1375 1 CCC1375 1 CCC1375

* ES30, START S/N AS4030091

* ES50, START S/N AS4030115

CAP-600

16

AIR COOLED, SINGLE STAGE MODEL

ES-150

DESCRIPTION Qty.

Req. MODEL

ES150

Inlet Valve Assembly, 1st Stage 3 70125-31000

Outlet Valve Assembly, 1st Stage 3 70125-41000

Air Strainer Assembly 3 70123-66001

VALVE

ASSEMBLIES

Breather Assembly 1 70124-57600

MAIN PARTS LISTING FOR MODEL ES-150

DESCRIPTION Qty.

Req. MODEL

ES150

1. Inlet Valve Seat 3 70125-31010

2. Inlet Valve Receiver 3 70125-31021

3. Inlet & Outlet Valve Plate 6 70125-31030

4. Inlet Valve Spring 3 70125-31070

5. Inlet Valve Unloading Fork Guide 3 70125-31090

6. Unloading Spring 3 70125-11230

VALVE &

UNLOADERS

7A. Valve Gasket 6 70125-11110

MAIN PARTS LISTING FOR MODEL CAP-600

ES-150 (Continued)

17

DESCRIPTION Qty. Req. MODEL ES150

7B Inlet Valve Unloading Fork 3 70125-31080

8. Locknut 3 92517-231200

10. Outlet Valve Seat 3 70125-41011

11. Outlet Valve Receiver 3 70125-41025

12. Outlet Valve Spring 3 70125-41074

13. Outlet Valve Bolt 3 70124-41810

14. Nut (Outlet Valve) 6 92502-131000

15. Inlet Valve Push Cover, 1st Stage 3 70125-11151

16. O – Ring G 65 3 93602-810065

17. Viton O – Ring G 65 (Outlet Valve) 3 93602-870065

18. Unloading Piston, 1st Stage 3 70125-11220

19. O – Ring P 22A 3 93601-870022A

VALVES & UNLOADERS

(Cont’d)

20. Outlet Valve Push Cover, 1st Sta

g

e 3 70125-11451

21A. Cylinder Head Assembly 70135-11000A

21. Cylinder Head (1st) 3 70125-11010

21B. S/N A311XXXX AND LATER 3 70135-11011

22. Cylinder & Head Gasket, 1st Stage 3 70125-11612

22A. S/N A311XXXX AND LATER 3 70135-11612

23. Cylinder (1st) 3 70135-51011

23A. S/N 3020000 THRU A311XXXX 3 70135-51010

23B. S/N A311XXXX AND LATER 3 70135-51011

24. Cylinder & Case Gasket 3 70135-51610

25. Compression Ring (1st) 6 70125-61030

26. Oil Control Ring (1st) 6 70125-61050

27. Piston (1st) 3 70125-61010

27A. S/N 3020000 & later use 3 70135-61010-1

28. Piston Pin Snap Ring 6 70125-61070

29. Piston Pin (1st) 3 70125-61120

30. Connecting Rod Piston Pin Bushing (1st) 3 70125-61081

31. Connecting Rod Assembly, 1st Stage 3 70125-61200

31A. S/N 3020000 & later use 3 70125-61200

32. Connecting Rod Crank Pin Metal 6 70125-61090

33. Connecting Rod Bolt 6 70125-61250

33A. Oil Splash Dipper H.P. -

34. Oil Splash Dipper 3 70135-61281

CYLINDERS

35. Oil S

p

lash Di

pp

er Bolt 3 92501-130800

42. Crankshaft 1 70135-56011

43. Counterweight 2 70135-56031

44. Lockwasher 2 70135-56830

45. Bolt 2 70135-56811

46. Crankcase 1 70135-57010-4024

47. Front Bearing Cover 1 70135-57030

48. Front Bearing Cover Gasket 1 70135-57950

49. Rear Bearing Cover 1 70134-57061

49A. S/N 3020000 & later use 1 70134-57061

50. Rear Bearing Cover Gasket 1 70134-57960

51. Front Bearing 1 93502-30310

52. Rear Bearing 1 93502-32210

53. Front Oil Seal 1 70134-57080

54. V – Pulley Pin 1 70134-56060

55A. Compressor Fan 1 70135-76310

55B. Compressor Pulley 1 70135-76011

56. Compressor Pulley Washer 1 70124-76210

57. Compressor Pulley Set Bolt 1 91501-1312050

58. Gauge Cover 1 70124-57700

59. Gauge Cover Seal 1 70124-57730

60. Crankcase Oil Cap 1 CCC1257

61. Crankcase Oil Plug 1 90112-100404

67. Air Strainer Filter 3 70123-66140

69. Outlet Pipe Joint B 1 70135-87021

70. Compressor Body Discharge Piping Assy. 2 70135-87100 (Long)

70A. S/N 3020000 & Later Use 2 70135-87200 (Short)

71. Outlet Pipe Joint A 1 70135-87011

73. Outlet Pipe Joint C 1 70135-87031

74. Gasket (Manifold) 3 70125-87510

Discharge Piping Assembly 1 70135-87700

Discharge Piping Assembly 1 70135-87800

CRANKCASE & CRANK ASSEMBLY

Dischar

g

e Pi

p

in

g

Assembl

y

1 70135-87900

Copper Connector -

Copper Connector -

Copper Connector -

75. Breather Assembly 1 CCC1258

CAP-600

AIR COOLED SINGLE STAGE

MODEL ES-150A

18

CAP-600

AIR COOLED SINGLE STAGE

MODEL ES-150B

18A

CAP-600

19

MAIN PARTS LISTING FOR

MODEL ES150A

ITEM

NO. PART

NO. DESCRIPTION QTY

1 91501-1310025 BOLT, M10 X 25 10

2 92521-191000 COPPER WASHER 22

3 70134-57061

REAR BEARING COVER 1

4 70131B81-57670 TUBE & BRTHR. ASSY. 1

4a 70131BA1-57670 TUBE, BREATHER 1

4b CCC1697 BREATHER, ASSY. 1

5 70134-57590

REAR COVER OIL BAFFLE 1

6 70134-57960

REAR BRG CVR PACKING 1

7 70123-57190-4010 CRANKCASE OIL CAP 1

8 91507-2305016 GAUGE SET BOLT 4

9 70124-57740 OIL GLASS & COVER 1

9a 70124-57700 OIL COVER 1

10 70124-57750 OIL COVER GLASS 1

11 70124-57730 GAUGE COVER SEAL 1

12 90112-100404 CRANKCASE OIL PLUG 1

13 70135-57010-4024 CRANKCASE 1

14 93502-30310 BEARING #30310 1

15 70135-56011 CRANKSHAFT 1

16 701312A1-56032

CRANKSHAFT CTR. WGT. 2

17 70135-56830 CTR WGT LK WASHER 2

18 70135-56811 CTR WGT MGT BOLT 2

19 70134-56060 V-PULLEY KEY 1

20 93502-32210 BEARING #32210 1

21 70135-57950 FRONT BEARING GASKET 1

22 70134-57080 FRONT OIL SEAL 1

23 70135-57030 FRONT BEARING COVER 1

24 70135-76011 COMPRESSOR PULLEY 1

25 70135-76310 COMP PULLEY FAN 1

26 92522-130800 WASHER 6

27 91501-2308030 BOLT 6

28 70124-76210 PULLEY THRUST WASHER 1

29 92522-131200 SPRING WASHER 31

30 91501-1312050 BOLT 1

31 70135-51610 CYL & CASE PACKING 3

32 70135-51810 CYL & CASE BOLT 12

33 70135-61281 OIL SPLASH DIPPER 3

34 92501-130800 NUT 3

35 70125-61090 CONN.ROD CRANK PIN METL 6

36 70125-61200 CONN.ROD ASS’Y 3

37 70125-61250 CONN.ROD ASS’Y BOLT 6

38 50135-61081 CONN.ROD CRANK PIN METL 3

39 70125-61070 PISTON PIN SNAP RING 6

40 70125-61120 PISTON PIN 3

41 70135-61010-1 PISTON 3

42 70135-61050 OIL CONTROL RING 6

43 70135-61030 COMPRESSION RING 6

44 70135-51011 CYLINDER 3

45 92501-131200 NUT 12

46 70135-11610 CYL & HEAD PACKING 3

47 91501-1312035 BOLT 18

48 70135-11011 CYLINDER HEAD 3

49 70125-11110 I/O VALVE SEAT GASKET 6

50 70125-31023 INLET VALVE RECEIVER 3

ITEM

NO. PART

NO. DESCRIPTION QTY

51 70125-31070 INLET VALVE SPRING 3

52 70125-31030 PLATE, INLET VALVE 3

53 70125-31010 INTER VALVE SEAT 3

54 70125-31090 I. VALVE UNLOAD FORK GUIDE 3

55 70125-11230 UNLOADING SPRING 3

56 70125-31080 I.VALVE UNLOAD FORK 3

57 92517-231200 SLOTTED NUT 3

58 93601-810022A O-RING P#22A 3

59 70125-11220 UNLOADING PISTON 3

60 93602-810065 O-RING G#65 3

61 70125-11151 I. VALVE PUSH COVER 3

62 91501-1310025 BOLT 24

63 90112-100101 SCREW PLUG 3

64 70124-41810 BOLT 3

65 70125-41012 OUTLET VALVE SEAT 3

66 701212A-41075 OUTLET VALVE SPRING 9

67 70125-41025 OUTLET VALVE RECEIVR 3

68 92501-231000 NUT 6

69 93602-870065 VITON O-RING G#65 3

70 70125-11451 O. VALVE PUSH COVER 3

71 701312A1-87032 DIST. MANIFOLD #C 1

72 70135-87101 COMP.BODY DIS. PIPING

ASSEMBLY 1

73 701312A1-87022 DIST. MANIFOLD #B 1

74 70135-87201 COMP.BODY DIS. PIPING

ASSEMBLY 1

75 701312A2-87011 DIST. MANIFOLD #A 1

76 70125-41030 PLATE, OUTLET VALVE 3

77 70125-41001 OUTLET, VALVE ASSY. 3

78 70125-31000 INLET, VALVE ASSY. 3

79 70123-66001 AIR STRAINER ASSY. 3

80 70123-66140 AIR STRAINER FILTER 3

CAP-600

19A

MAIN PARTS LISTING FOR

MODEL ES150B

ITEM

NO. PART

NO. DESCRIPTION QTY

1 91501-1310025 BOLT, M10 X 25 10

2 9252615-101000-0 COPPER WASHER 10

3 701310A1-57061 REAR BEARING COVER 1

4 70131B81-57670 TUBE & BRTHR. ASSY. 1

4a 70131BA1-57670 TUBE, BREATHER 1

4b CCC1697 BREATHER, ASSY. 1

5 701310A1-57590 REAR COVER OIL BAFFLE 1

6 701310A1-57070 REAR BRG CVR GASKET 1

7 70123-57190-4010 CRANKCASE OIL CAP 1

8 9151313-1105020-5202 GAUGE SET BOLT 4

9 701210A1-57740 OIL GLASS & COVER 1

9a 701210A1-57700 OIL COVER ASSY 1

10 70124-57750 OIL COVER GLASS 1

11 701210A1-57730 GAUGE COVER SEAL 1

12 9156310-400800 CRANKCASE OIL PLUG 1

13 701312A3-57010 CRANKCASE 1

14 9354504-30310 BEARING #30310 1

15 701312A1-56011 CRANKSHAFT 1

16 701312A1-56032 CRANKSHAFT CTR. WGT. 2

17 701312A1-56830 CTR WGT LK WASHER 2

18 701312A1-56811 CTR WGT MGT BOLT 2

19 701310A1-56060 V-PULLEY KEY 1

20 9354501-32210 BEARING #32210 1

21 70135-57950 FRONT BEARING GASKET 1

22 701310A1-57080 FRONT OIL SEAL 1

23 701312A1-57030 FRONT BEARING COVER 1

24 701312A1-76011 COMPRESSOR PULLEY 1

25 70131283-76310 COMP PULLEY FAN 1

26 9253113-100800-8 WASHER 6

27 9150113-1108030-5202 BOLT 6

28 701210A1-76210 PULLEY THRUST WASHER 1

29 9253113-101200-8 SPRING WASHER 1

30 9150113-1112050-5608 BOLT 1

31 701312A1-51030 CYL & CASE PACKING 3

32 701312A1-51810 CYL & CASE BOLT 12

33 701312A1-61281 OIL SPLASH DIPPER 3

34 9250113-120800-538 NUT 3

35 701212A1-61090 CONN.ROD CRANK PIN METL 6

36 701212A1-61200 CONN.ROD ASS’Y 3

37 70125-61250 CONN.ROD ASS’Y BOLT 6

38 501312A1-61081 CONN.ROD CRANK PIN METL 3

39 701212A1-61070 PISTON PIN SNAP RING 6

40 701212A1-61120 PISTON PIN 3

41 701312A1-61010 PISTON 3

42 701212A1-61050 OIL CONTROL RING 6

43 701212A1-61030 COMPRESSION RING 6

44 701312A3-51010 CYLINDER 3

45 92501-131200 NUT 12

46 701312A3-11020 CYL & HEAD GASKET 3

47 9250113-121200-538 BOLT 12

48 701312A3-11010 CYLINDER HEAD 3

49 701212A1-11110 I/O VALVE SEAT GASKET 6

ITEM

NO. PART

NO. DESCRIPTION QTY

50 701212A1-31023 INLET VALVE RECEIVER 3

51 701212A1-31070 INLET VALVE SPRING 3

52 501212A1-31030 PLATE, INLET VALVE 3

53 701212A1-31010 INTER VALVE SEAT 3

54 701212A1-31090 I. VALVE UNLOAD FORK GUIDE 3

55 701212A1-11230 UNLOADING SPRING 3

56 701212A1-31080 I.VALVE UNLOAD FORK 3

57 9250413-151200-532 SLOTTED NUT 3

58 9360187-350217 O-RING P#22A 3

59 701212A1-11220 UNLOADING PISTON 3

60 9360287-310644 O-RING G#65 3

61 701212A1-11151 I. VALVE PUSH COVER 3

62 91501-1310025 BOLT 3

63 90112-100101 SCREW PLUG 24

64 70124-41810 BOLT 3

65 701212A1-41012 OUTLET VALVE SEAT 3

66 701212A1-41075 OUTLET VALVE SPRING 3

67 701212A1-41025 OUTLET VALVE RECEIVR 9

68 92501-231000 NUT 3

69 9360287-310644 VITON O-RING G#65 6

70 701212A1-11451 O. VALVE PUSH COVER 3

71 701312A1-87032 DIST. MANIFOLD #C 3

72 70135-87101 COMP.BODY DIS. PIPING

ASSEMBLY 1

73 701312A1-87022 DIST. MANIFOLD #B 1

74 701312A2-87100 COMP.BODY DIS. PIPING

ASSEMBLY 1

75 701312A2-87011 DIST. MANIFOLD #A 1

76 70125-41030 PLATE, OUTLET VALVE 1

77 701212A1-41001 OUTLET, VALVE ASSY. 3

78 701212A1-31000 INLET, VALVE ASSY. 3

79 701312A1-66000 AIR STRAINER ASSY. 3

80 701208A1-66110 AIR STRAINER FILTER 3

3

CAP-600

20

AIR COOLED

TWO STAGE MODELS E-11 & E-23

CAP-600

21

MAIN PARTS LISTING FOR

TWO STAGE MODELS E-11 & E-23

VALVES Qty.

Req. MODEL E11 Qty.

Req. MODEL E23

1. Inlet & Outlet Valve Plate (1st) 2 70112-31030 4 70112-31030

2. Inlet Valve Spring (1st) 1 70112-31070 2 70112-31070

3. Inlet Valve Receiver (1st) 1 70112-31020 2 70112-31020

4. Inlet Valve Snap Ring (1st) 1 93610-130232 2 93610-130232

5. Outlet Valve Spring (1st) 1 70112-41070 2 70112-41070

6. Outlet Valve Push Cover Gasket (1st) 1 70112-11461 2 70112-11461

7. Outlet Valve Push Cover 1 70112-11450 2 70112-11450

8. Inlet & Outlet Valve Plate (2nd) 2 70162-32030 2 70111-31030

9. Inlet Valve Spring (2nd) 1 70162-32070 2 70172-32070

10. Inlet Valve Receiver (2nd) 1 70162-32020 1 70111-31020

11. Inlet Valve Snap Ring (2nd) 1 93610-130222 1 93610-130225

12. Outlet Valve Spring (2nd) 1 70162-42070 1 70172-42070

14. Outlet Valve Push Cover Gasket (2nd) 1 70162-12650 1 70111-11461

15. Outlet Valve Push Cover (2nd) 1 70112-12450 1 70111-11450

CYLINDERS

16. Cylinder Head (1st) 1 70112-11010 2 70112-11010

17. Cylinder & Head Gasket (1st) 1 70112-11612 2 70112-11612

18. Cylinder (1st) 1 70112-51010 2 70112-51010

19. Cylinder & Case Gasket 2 70112-51610 3 70112-51610

20. Compression Ring (1st) 2 70112-61030 4 70112-61030

21. Oil Control Ring (1st) 1 70112-61050 2 70112-61050

22. Piston (1st) 1 70112-61011 2 70112-61011

23. Piston Pin (1st) 1 70112-61120 2 70112-61120

24. Piston Pin Snap Ring 4 70112-61070 6 70112-61070

25. Connecting Rod Assembly (1st) 2 70112-61200-1 2 70112-61200-1

26. Connecting Rod Bolt 2 70112-61250 3 70112-61250

27. Oil Splash Dipper 70122-61282 2 70122-61282

27A. Oil Splash Dipper - 1 70132-61290

28. Oil Splash Dipper Bolt 2 91507-2304010 3 91507-2304010

29. Cylinder Head Bolt 8 91501-1308025 12 91501-1308025

30. Cylinder Head (2nd) 1 70162-12010 1 70172-12010

31. Cylinder & Head Gasket (2nd) 1 70162-12610 1 70111-11612

32. Cylinder (2nd) 1 70162-52010 1 70172-52010

34. Compression Ring (2nd) 2 70162-62030 2 70111-61030

35. Oil Control Ring (2nd) 2 70162-62050 2 70111-61050

36. Piston (2nd) 1 70162-62010 1 70172-62010-1

37. Piston Pin (2nd) 1 70162-62120 1 70172-62120

38. Connecting Rod Assembly (2nd) - 1 70182-62200

CRANK ASSEMBLY

39. Crankcase 1 70122-57010-4024 1 70132-57010-4024

40. Crankshaft 1 70122-56010 1 70132-56010

41. Front Bearing Cover 1 70122-57030 1 70122-57030

42. Front Bearing Cover Gasket 1 70122-57950 1 70122-57950

43. Rear Bearing Cover 1 70122-57060 1 70122-57060

44. Rear Bearing Cover Gasket 1 70122-57960 1 70122-57960

45. Bearing 2 93501-6205 2 93501-6205

46. Front Oil Seal 1 70122-57080 1 70122-57080

47. V–Pulley Pin 1 70112-56060 1 70112-56060

48. Compressor Pulley 1 70122-76011 1 70132-76010

49. Compressor Pulley Thrust Washer 1 70112-76210 1 70112-76210

50. Compressor Pulley Thrust Bolt 1 91501-1308025 1 91501-1308025

51. Breather Assembly 1 CCC1375 1 CCC1375

52. Oil Gauge & Gauge Cover 1 70111-57700 1 70111-57700

٭52 A. Oil Level Gauge Assy. 1 70704-57700 1 70704-57700

53. Gauge Cover Seal 1 70111-57730 1 70111-57730

٭53 A. Oil Level Gauge “O” Ring 1 93602-8126026 1 93602-8126026

54. Crankcase Oil Plug 1 90112-100202 1 90112-100202

54A. Oil fill cap - 1 70101-57190-4010

54B. “O” Ring - 1 93601-810016

UNLOADERS

55. Auto-Unloader Assembly 2 70112-11201 3 70112-11201

56. Auto-Unloader Spring 2 70112-11230 3 70112-11230

57. Auto-Unloader Piston 2 70112-11221 3 70112-11221

58. O-Ring (Unloader) 2 93601-810016 3 93601-810016

AIR STRAINER ASSEMBLY

61. Air Strainer Filter 1 70111-66141 2 70111-66141

63A. Discharge Piping Assembly - 1 70132-87100

63B. Discharge Piping Assembly 1 70172-87300 1 70172-87300

64. Air Strainer Assembly 1 70111-66001 2 70111-66001

65. Outlet Pipe Joint #A 2 70122-87010 3 70122-87010

65A. Outlet Pipe Joint #B 1 70132-87020

• E11, START S/N AS4040633

• E23, START S/N AS4030313

CAP-600

22

AIR COOLED, TWO STAGE

MODELS E-50 & E-71

DESCRIPTIONS Qty. Req. MODEL

E50 Qty. Req. MODEL

E71

Inlet Valve Assembly, 1st Stage 2 70123-31000 2 70124-31000

Inlet Valve Assembly, 2nd Stage 1 70173-32000 1 70173-32000

Outlet Valve Assembly, 1st Stage 2 70123-41000 2 70124-41000

Outlet Valve Assembly, 2nd Stage 1 70123-41000 1 70123-41000

Air Strainer Assembly 2 70123-66000 2 70123-66000

VALVE

ASSEMBLIES

Breather Assembly 1 70103-57600-4024 1 70124-57600-4010

MAIN PARTS LISTING FOR

TWO STAGE MODELS E-50 & E-71

MODEL E50 MODEL E71

DESCRIPTIONS Qty

Req’d 1st Stage Qty

Req’d 2nd Stage Qty

Req’d 1st Stage Qty

Req’d 2nd Stage

1. Inlet Valve Seat 2 70123-31010 1 70123-31010 2 70124-31010 1 70123-31010

2. Inlet Valve Receiver 2 70123-31020 1 70123-31020 2 70124-31020 1 70123-31020

3. Inlet & Outlet Valve Plate 4 70123-31030 2 70123-31030 4 70124-31030 2 70123-31030

4. Inlet Valve Spring 2 70123-31070 1 70123-31070 2 70124-31070 1 70123-31070

5. Inlet Valve Unloading Fork Guide 2 70123-31090 1 70123-31090 2 70124-31090 1 70123-31090

6. Unloading Spring 2 70123-11230 1 70123-11230 2 70124-11230 1 70123-11230

7. Inlet Valve Unloading Fork 2 70123-31080 1 70123-31080 2 70124-31080 1 70123-31080

8. Slotted Nut 2 92502-230800 1 92502-230800 2 92502-230800 1 92502-230800

9. Cotter Pin 2 93701-130220 1 93701-130220 2 93701-130220 1 93701-130220

10. Outlet Valve Seat 2 70123-41011 1 70123-41011 2 70124-41011 1 70123-41011

11. Outlet Valve Receiver 2 70123-41020 1 70123-41020 2 70124-41020 1 70123-41020

VAVLES & UNLOADERS

12A. Seat Gaskets 4 70123-11110 2 70123-11110 4 70124-11110 2 70123-11110

CAP-600

MAIN PARTS LISTING FOR

TWO STAGE MODELS E-50 & E-71 (CONTINUED)

MODEL E-50 MODEL E-71

DESCRIPTION QTY 1st Stage QTY 2nd Stage QTY 1st Stage QTY 2nd Stage

12B Outlet Valve Spring 2 70123-41070 1 70123-41070 2 70124-41070 1 70123-41070

13 Outlet Valve Bolt 2 70123-41810 1 70123-41810 2 70124-41810 1 70123-41810

14 Nut (Outlet Valve) 2 92502-230800 1 92502-230800 2 92502-230800 1 92502-230800

15 Inlet Valve Push Cover 2 70123-11150 1 70123-11150 2 70124-11150 1 70123-11150

16 O-ring G-40(Inlet Valve) 2 93602-810040 1 93602-810040 2 93602-810055 1 93602-810055

17 Viton O-ring G-40 (Outlet Valve) 2 93602-870040 1 93602-870040 2 93602-870055 1 93602-870040

18 Unloading Piston 2 70123-11220 1 70123-11220 2 70124-11220 1 70123-11220

19 O-ring P-20 2 93601-810020 1 93601-870020 2 93601-810021 1 93601-870020

Valves &

Unloaders

20 Outlet Valve Push Cover 2 70123-11450 1 70123-11450 2 70124-11450 1 70123-11450

21 Cylinder Head (1st) 2 70123-11010 2 70124-11010

22 Cylinder & Head Gasket 2 70123-11612 1 70123-11612 2 70124-11612 1 70123-11612

23 Cylinder (1st) 2 70123-51012 2 70124-51011

23A S/N A311xxxx & Later Use 2 70123-51012 2 70124-51011

24 Cylinder & Case Gasket 2 70123-51610 1 70123-51610 2 70124-51610 1 70124-51610

25 Compression Ring (1st) 4 70123-61030 4 70124-61030

26 Oil Control Ring (1st) 4 70123-61050 4 70124-61050

27 Piston (1st) 2 70123-61011 2 70124-61011-1

27A S/N 3020000 & Later Use 2 70123-61011 2 70124-61011-1

28 Piston Snap Ring 4 70123-61070 2 70123-61070 4 70124-61070 2 70124-61070

29 Piston Pin (1st) 2 70123-61120 2 70124-61120

30 Con’cting Rod Pist. Pin Bushing 2 70123-61081 1 70173-62080 2 70124-61080 1 70174-62081

30A Bushing S/N 3020000 & Later use 2 70123-61081

30B Nedl Brg.S/N A303XXXX&LatrUse 1 93503-RNA6903R

30C Nedl Brg.(2nd)S/N A405XXXX&Latr 1 93503-TA1725

31 Connecting Rod Assy 2 70123-61200 1 70173-62200 2 70124-61201 1 70174-62202

31B Conn. Rod Assy., 2nd Stage S/N

A405XXXX & Later Use 1 70173-62200

32 Connecting Rod Crank Pin Metal 4 70123-61090 2 70123-61090 4 70124-61090 2 70124-61090

33 Connecting Rod Bolt 4 70125-61250 2 70125-61250 4 70125-61250 2 70125-61250

34 Oil Splash Dipper 2 70122-61282 1 70132-61290 2 70134-61281 1 70134-61290

35 Oil Splash Dipper Bolt 2 91507-2304012 1 91507-2304012 2 91507-2304012 1 91507-2304012

36 Cylinder Head (2nd) 1 70123-11010 1 70174-12010

37 Cylinder (2nd) 1 70173-52010 1 70174-52011

37A Cyl (2nd),S/N 3020000 & Later Use 1 70174-52011

38 Compression Ring (2nd) 3 70112-61030 3 70123-61030

39 Oil Control Ring (2nd) 1 70112-61050 2 70123-61050

40 Piston (2nd) 1 70173-62010-1 1 70174-62010-1

Cylinders

41 Piston Pin (2nd) 1 70173-62120 1 70174-62120

42 Crankshaft 1 70133-56011 1 70134-56010

43 Crankshaft - 1 70134-56030

44 Counterweight Lock Washer - 2 70124-56830

45 Counterweight Mtg. Bolt - 2 70124-56810

46 Crankcase 1 70133-57010-4024 1 70134-57010-4024

47 Front Bearing Cover 1 70133-57030 1 70134-57030

48 Front Bearing Cover Gasket 1 70123-57950 1 70124-57950

49 Rear Bearing Cover 1 70133-57061 1 70134-57061

49A Rear Brg Cvr, S/N 3020000 & Latr 1 70133-57061 1 70134-57061

50 Rear Brg Cvr Gasket 1 70133-57960 1 70134-57960

51 Front Bearing 1 93501-6306 1 93502-32210

52 Rear Bearing 1 93501-6306 1 93502-32210

53 Front Oil Seal 1 70123-57080 1 70134-57080

54 V-Pulley Pin 1 70123-56061 1 70134-56060

55A Compressor Fan - 1 70124-76310

55B Compressor Pulley 1 70133-76010 1 70134-76011

56 Compressor Pulley Washer 1 92521-232000 1 70124-76210

57 Compressor Pulley Set Bolt 1 91501-1312030 1 91501-1312040

58 Gauge Cover 1 70111-57700 1 70124-57700

٭

5

8 A Oil Level Gauge Assy. 1 70704-57700 -

59 Gauge Cover Seal 1 70111-57730 1 70124-57730

٭

5

9 A Oil Level Gauge “O” Ring 1 93602-8126026 -

60 Crankcase Oil Cap 1 CCC1257 1 CCC1257

61 Crankcase Oil Plug 1 90112-100404 1 90112-100404

62 Breather Assembly 1 CCC1375 1 CCC1258

67 Air Strainer Filter 2 70123-66140 2 70123-66140

69 Outlet Pipe Joint B 1 70123-87020 1 70174-87020

70A Comp.body.discharg.pipe.assy. 1st 1 70133-87101 short 1 70134-87101 short

70B Comp.body.discharg.pipe.assy. 1st - -

70C Comp.body.discharg.pipe.assy.2nd - -

70D Comp.body.discharg.pipe.assy.2nd 1 70173-87300 long 1 70174-87300 long

71 Outlet Pipe Joint A 2 70123-87010 3 70124-87010

72 Outlet Pipe Joint D 1 70173-87010

73 Outlet Pipe Joint C

Crankcase & Crank Assembly

74 Gasket Manifold - -

*E 50, START S/N AS4030343

23

CAP-600

24

AIR COOLED, TWO STAGE

MODEL E-15

Description Qty.

Req. MODEL

E15

Inlet Valve Assembly, 1st Stage 2 70125-31000

Inlet Valve Assembly, 2nd Stage 1 70175-32000

Outlet Valve Assembly, 1st Stage 2 70125-41000

Outlet Valve Assembly, 2nd Stage 1 70175-42000

Air Strainer Assembly 2 70123-66000

VALVE ASSEMBLIES

Breather Assembly 1 70124-57600-4010

MAIN PARTS LISTING FOR TWO STAGE MODEL E-15

MODEL E15

Description Qty

Req’d 1st Stage Qty

Req’d 2nd Stage

1. Inlet Valve Seat 2 70125-31010 1 70124-31010

2. Inlet Valve Receiver 2 70125-31022 1 70124-31020

3. Inlet & Outlet Valve Plate 4 70125-31030 2 70175-42030

4. Inlet Valve Spring 2 70125-31070 1 70124-31070

5. Inlet Valve Unloading Fork Guide 2 70125-31090 1 70124-31090

6. Unloading Spring 2 70125-11230 1 70124-11230

7. Inlet Valve Unloading Fork 2 70125-31080 1 70124-31080

8. Slotted Nut 2 92502-230800 1 92502-230800

9. Cotter Pin 2 93701-130220 1 93701-130220

10. Outlet Valve Seat 2 70125-41011 1 70124-41010

11. Outlet Valve Receiver 2 70125-41021 1 70175-42020

VAVLES & UNLOADERS

12A. Seat Gaskets 4 70125-11110 2 70124-11110

CAP-600

25

MAIN PARTS LISTING FOR

TWO STAGE MODEL E-15 (Continued)

MODEL E15

DESCRIPTION Qty

Req’d 1st Stage Qty

Req’d 2nd Stage

12B. Outlet Valve Spring 2 70125-41071 1 70124-41072

13. Outlet Valve Bolt 2 70124-41810 1 70124-41810

14. Nut (Outlet Valve) 2 92501-231000 1 92501-231000

15. Inlet Valve Push Cover 2 70125-11151 1 70175-12150

16. O-Ring G-65 (Inlet Valve) 2 93602-810065 1 93602-870055

17. Viton O-Ring G-65 (Outlet Valve) 2 93602-870065 1 93602-870055

18. Unloading Piston 2 70125-11220 1 70124-11220

19. O-Ring P-20 2 93601-810022A 1 93601-870021

20. Outlet Valve Push Cover 2 70125-11451 1 70175-12450

VALVES &

UNLOADERS

20A. Outlet Valve Push Cover Push Pipe 1 70124-11120

21. Cylinder Head (1st) 2 70125-11010

21A. S/N A31XXXX & Later Use 2 70135-11010

22. Cylinder & Head Gasket 2 70125-11612 1 70124-11612

22A. S/N A311XXXX & Later Use 2 70135-11612

23. Cylinder (1st) 2 70125-51010

23A. S/N A311xxxx & Later Use 2 70135-51011

24. Cylinder & Case Gasket 2 70135-51610

25. Compression Ring (1st) 4 70125-61030

26. Oil Control Ring (1st) 4 70125-61050

27. Piston (1st) 2 70135-61010-1

27A. S/N 3020000 & Later Use 2 70135-61010-1

28. Piston Snap Ring 4 70125-61070 2 70125-61070

29. Piston Pin (1st) 2 70125-61120

30. Connecting Rod Piston Pin Bushing (1st) 2 70125-61081 1 70175-62080

30D. Needle Bearing (2nd) S/N A409XXXX & Later Use 1 93503-NK28/30

31. Connecting Rod Assembly, 1st Stage 2 70125-61200 1 70175-61200

31C. Connecting Rod Assembly, 2nd Stage 1 70175-62201

32. Connecting Rod Crank Pin Metal 4 70125-61090 2 70125-61090

33. Connecting Rod Bolt 4 70125-61250 2 70125-61250

34. Oil Splash Dipper 2 70135-61281 1 70135-61281

35. Oil Splash Dipper Bolt 2 92501-130800 1 92501-130800

36. Cylinder Head (2nd) 1 70175-12010

37. Cylinder (2nd) 1 70175-52010

38. Compression Ring (2nd) 3 70124-61030

39. Oil Control Ring (2nd) 2 70124-61050

40. Piston (2nd) 1 70175-62010-1

40A. Piston (2nd), S/N A409XXXX & Later Use 1 70175-62011-1

41. Piston Pin (2nd) 1 70175-62121

CYLINDERS

41A. Piston Pin (2nd), S/N A409XXXX & Later Use 1 70175-62121

42. Crankshaft 1 70135-56011

43. Crankshaft Counterweight 1 70135-56030

44. Counterweight Lock Washer 2 70124-56830

45. Counterweight Mounting Bolt 2 70135-56811

46. Crankcase 1 70135-57010-4024

47. Front Bearing Cover 1 70135-57030

48. Front Bearing Cover Gasket 1 70135-57950

49. Rear Bearing Cover 1 70134-57061

49A. Rear Bearing Cover, S/N 3020000 & Later Use 1 70134-57061

50. Rear Bearing Cover Gasket 1 70134-57960

51. Front Bearing 1 93502-30310

52. Rear Bearing 1 93502-32210

53. Front Oil Seal 1 70134-57080

54. V-Pulley Pin 1 70134-56060

55A. Compressor Fan 1 70135-76310

55B. Compressor Pulley 1 70135-76011

56. Compressor Pulley Washer 1 70135-76210

57. Compressor Pulley Set Bolt 1 91501-1312050

58. Gauge Cover 1 70124-57700

59. Gauge Cover Seal 1 70124-57730

60. Crankcase Oil Cap 1 CCC1257

61. Crankcase Oil Plug 1 90112-100404

62. Breather Assembly 1 70124-57600-4010

67. Air Strainer Filter 2 70123-66140

69. Outlet Pipe Joint B 1 70175-87021

70A. Compressor Body Discharge Piping Assembly, 1st 1 70135-87100(long)

70B. Compressor Body Discharge Piping Assembly, 1st 1 70135-87200(short)

70C. Compressor Body Discharge Piping Assembly, 2nd 1 70175-87400(short)

70D. Compressor Body Discharge Piping Assembly, 2nd 1 70175-87300(long)

71. Outlet Pipe Joint A 1 70175-87010

72. Outlet Pipe Joint D 1 70125-87020

73. Outlet Pipe Joint C 1 70175-87030-4010

CRANKCASE AND CRANK ASSEMBLY

74. Gasket Manifold 4 70125-87510

CAP-600

26

AIR COOLED TWO STAGE MODEL E-35

46A

CAP-600

27

MAIN PARTS LISTING FOR

AIR COOLED TWO STAGE MODEL E-35

(FORMERLY B-1)

DESCRIPTION QTY PART NO.

1. Discharge Elbow 1 70123-87050

2. Discharge Elbow Nut (Not Shown) 1 79922-130606

3. Cylinder Head Bolt 6 91501-1310085

4. Spring Washer 6 92522-130800

5. Cylinder Head 1 70152-11010

6. Unloading Tee * # 1 79922-150101

7. Bolt 2 91521-1306025

8. Spring Washer 2 92522-130600

9. Upper Cover 1 70153-11270

10. Upper Cover Gasket 1 70153-11641

11. Unloader Assembly (1st)(Includes 12-

16) 1 70152-11201

12. Unloading Piston 1 70153-11222

13. Unloading Spring 1 70153-11231

14. Unloading Cylinder 1 70153-11211

15. Unloading Fork (1st) 1 70152-31080

16. Bolt 1 91501-1306015

17. Cylinder Head Valve Seat Gasket 1 70152-11612

18. Valve Plate Assembly (Includes 19-27) 1 70152-31000

19. Valve Seat Bolt 3 91521-1305012

20. Valve Seat (Upper) 1 70152-31010

21. Valve Seat Gasket 1 70152-31120

22. Valve Plate (1st) 4 70152-31030

23. Valve Plate Spring (1st) 4 70152-31070

24. Valve Plate (2nd) 2 70152-32030

25. Valve Plate Spring (2nd) 2 70152-32070

26. Valve Seat (Bottom) 1 70152-31020

27. Nut 1 92501-230500

28. Cylinder-Valve Seat Gasket 1 70152-11622

29. Cylinder 1 70152-51010

30. Cylinder Crankcase Gasket 1 70152-51610

31. Bolt 11 91501-1310030

32. Copper Washer 6 92521-190800

33. Crankcase Oil Cap 1 70101-57190-4010

34. Oil Cap O-Ring 1 93601-810016

35. Crankcase 1 70152-57010

36. Bearing #6025 (Front & Rear) 2 93501-6205

37. Rear Cover Gasket 1 70152-57960

38. Rear Cover 1 70152-57060

39. Rear Cover Bolt 3 91521-1308030

40. Copper Washer 7 92521-190800

41. Oil Level Gauge & Gauge Cover 1 70111-57700

42. Gauge Cover Seal 1 70111-57730

43. Crankcase Oil Plug (1/4” NPT) 1 90112-100303

44. Inter-Cooler Bolt 3 91521-1308050

45. Gasket 1 70152-71612

46. Inter-Cooler Body 1 70152-71110

46A. Gasket, Copper 1 70152-12280

DESCRIPTION QTY PART NO.

47. Inter-Cooler Body Gasket 1 70152-71622

48. Inter-Cooler Cover 1 70152-71160

49. Spring Washer 4 92522-130600

50. Bolt 4 91501-1306016

51. Compression Ring (1st) 2 70152-61030

52. Oil Control Ring (1st) 1 70152-61050

53. Piston (1st) 1 70152-61010

54. Piston Snap Ring 4 70152-61070

55. Connection Rod Assembly (1st) 1 70152-61200

56. Piston Pin Bush (1st) 1 70152-61080

57. Connecting Rod Assembly (2nd) 1 70152-62200

58. Piston Pin Bush (2nd) 1 70152-62080

59. Crank Pin Metal (Rod Bearing 2 Halves) 2 70152-61090

60. Crankshaft 1 70152-56010

61. Piston Pin (1st) 1 70152-61120

62. Compression Ring (2nd) 3 70152-62030

63. Piston Pin (2nd) 1 70152-62120

64. Oil Control Ring (2nd) 1 70152-62050

65. Piston (2nd) 1 70152-62010

66. Breather Assembly 1 CCC1375

67. V-Pulley Pin 1 70112-56060

68. Nut (Connecting Rod) 4 92501-130800

69. Spring Washer (Connecting Rod) 4 92522-130800

70. Bolt (Connecting Rod) 4 70152-61250

71. Front Cover Gasket 1 70152-57950

72. Front Cover 1 70152-57030

73. Front Oil Seal 1 70127-57080

74. Copper Washer 7 92521-190800

75. Bolt 4 91501-1310030

76. Compressor Pulley 1 70152-76010

77. Compressor Pulley Thrust Washer 1 70112-76210

78. Bolt 1 91501-1308025

79. Unloading Elbow * # 1 79926-150101

80. Unloader Assembly (2nd)(Includes 81-

85) 1 70152-12200

81. Unloader Cover (2nd) 1 70103-11271

82. Viton O-Ring Unloader (2nd) 1 93601-870009

83. Unloading Piston (2nd) 1 70152-12221

84. Unloading Spring (2nd) 1 70103-11230

85. Unloader Body 1 70153-12200

86. Air Strainer Assembly (Includes 87-92) 1 70152-66001

87. Air Strainer Cover Gasket 1 70152-66131

88. Air Strainer Cover 1 70153-66120

89. Air Strainer Bolt 1 70152-66160

90. Air Strainer Element 1 70152-66141

91. Nut (Self Lock) Air Strainer 1 92522-230600

92. Air Strainer Body 1 70152-66011

93. Intercooler Safety Valve (Not Shown) 1 VV431

* Includes Nut(S) And Sleeve(S) # Not Supplied On Basics

CAP-600

28

AIR COOLED TWO STAGE MODEL E-57

95

CAP-600

29

MAIN PARTS LISTING FOR

AIR COOLED TWO STAGE MODEL E-57

(FORMERLY B-2)

DESCRIPTION QTY PART NO.

1. Discharge Elbow 1 701210A1-87011

2. Discharge Elbow Nut (Not Shown) 1 79922-130707

3. Cylinder Head Bolt 6 91501-1310085

4. Spring Washer 6 92522-131000

5. Cylinder Head 1 70153-11011

6. Unloading Tee * # 1 90126-150101

7. Bolt 2 91521-1306025

8. Spring Washer 2 92522-130600

9. Upper Cover 1 70153-11270

10. Upper Cover Gasket 1 70153-11631

11. Lower Unloader Gasket 1 70153-11641

12. Unloader Assembly (1st)(Includes 13-17) 1 70153-11201

13. Unloading Piston 1 70153-11222

13A. Viton O-Ring Unloader (1ST) 1 93601-870015

14. Unloading Spring 1 70153-11231

15. Unloading Cylinder 1 70153-11211

16. Unloading Fork 1 70153-31080

17. Bolt 1 91501-1306016

18. Cylinder Head Valve Seat Gasket 1 70153-11612

19. Valve Plate Assembly (Includes 20-28) 1 70153-31001

20. Valve Seat Bolt 3 91521-1305012

21. Valve Seat (Upper) 1 70153-31011

22. Valve Seat Gasket 1 70153-31120

23. Valve Plate (1st) 4 70153-31032

24. Valve Plate Spring (1st) 4 70153-31072

25. Valve Plate (2nd) 2 70153-32032

26. Valve Plate Spring (2nd) 2 70153-32072

27. Valve Seat (Bottom) 1 70153-31021

28. Nut 2 92501-230500

29. Cylinder-Valve Seat Gasket 1 70153-11622

30. Cylinder 1 70153-51011

31. Cylinder Crankcase Gasket 1 70153-51611

32. Bolt 6 91501-1310030

33. Copper Washer 6 92521-191000

34. Crankcase Oil Cap 1 CCC1257

35. Oil Cap O-Ring 1 93601-810018

36. Crankcase 1 70153-57011

37. Bearing #6026 (Front & Rear) 2 93501-6206

38. Rear Cover Gasket 1 70153-57961

39. Rear Cover 1 70153-57061

40. Rear Cover Bolt 3 91521-1308030

41. Copper Washer 3 92521-190800

42. Oil Level Gauge & Gauge Cover 1 70111-57700

43. Gauge Cover Seal 1 70111-57730

44. Crankcase Oil Plug (1/4” NPT) 1 70153-12350

45. Inter-Cooler Bolt 3 91521-1308055

46. Gasket 1 70153-71611

47. Inter-Cooler Body 1 70153-71111

48. Inter-Cooler Body Gasket 1 70153-71622

DESCRIPTION QTY PART NO.

49. Inter-Cooler Cover 1 70153-71161

50. Spring Washer 6 92522-130600

51. Bolt 6 91501-1306016

52. Compression Ring (1st) 2 70124-61030

53. Oil Control Ring (1st) 2 70124-61050

54. Piston (1st) 1 70153-61011

55. Piston Pin Snap Ring 4 70153-61071

56. Connection Rod Assembly (1st) 1 70153-61211

57. Piston Pin Bush (1st) 1 70153-61081

58. Connecting Rod Assembly (2nd) 1 70153-62211

59. Piston Pin Bush (2nd) 1 70153-62081

59A. Piston Pin Needle Bearing (2nd) ** 1 93503-TA2420

60. Connecting Rod Bearing (2 Halves) 2 70153-61090

61. Crankshaft 1 70153-56011

62. Piston Pin (1st) 1 70153-61121

63. Compression Ring (2nd) 3 70153-62030

64. Piston Pin (2nd) 1 70153-62121

65. Oil Control Ring (2nd) 1 70153-62050

66. Piston (2nd) 1 70153-62011

67. Breather Assembly 1 CCC1258

68. V-Pulley Pin 1 70123-56061

69. Nut (Connecting Rod) 4 92501-230800

70. Spring Washer (Connecting Rod) 4 92522-130800

71. Bolt (Connecting Rod) 4 70153-61250

72. Front Cover Gasket 1 70153-57951

73. Front Cover 1 70153-57030

74. Front Oil Seal 1 70123-57080

75. Copper Washer 4 92521-190800

76. Bolt (Front Cover) 4 91501-1310030

77. Compressor Pulley 1 70153-76011

78. Compressor Pulley Thrust Washer 1 70123-76210

79. Compressor Pulley Bolt 1 91501-1310030

80. Unloading Elbow * # 1 79926-150101

81. Unloader Assembly (2nd)(Includes 82-86) 1 70153-12201

82. Unloader Cover (2nd) 1 70103-11271

83. Viton O-Ring Unloader (2nd) 1 93601-870009

84. Unloading Piston (2nd) 1 70153-12222

85. Unloading Spring (2nd) 1 70103-11231

86. Unloader Body (2nd) 1 70103-11211

87. Air Strainer Assembly (Includes 88-93) 1 70153-66002

88. Air Strainer Cover Gasket 1 70153-66132

89. Air Strainer Cover 1 70153-66121

90. Air Strainer Bolt 1 70153-66160

91. Air Strainer Element 1 70153-66142

92. Nut (Self Lock) Air Strainer 1 92507-230600

93. Air Strainer Body 1 70153-66012

94. Intercooler Safety Valve (Not Shown) 1 VV431

95. Gasket, Copper 1 70152-12280

* Includes Nut(S) And Sleeve(S) # Not Supplied On Basics

** S/N A4081331 & Later

CAP-600

30

INSPECTION & MAINTENANCE OF

E-57 VALVE ASSEMBLY

INSTRUCTION FOR E-57 COMPRESSOR MODEL HEAD VALVE ASSEMBLY INSPECTION AND MAINTENANCE.

Model E-57 valve assembly inspection and maintenance instruction.

1. Inspect valve assemblies every 1000 hours of operation or as necessary to maintain efficient operation.

2. Turn off power, red tag power supply switch (caution: Maintenance in progress – DO NOT START). Drain all air

pressure from system before starting work.

3. Disconnect air piping from head.

Remove valve package.

A1. Loosen and remove head bolts. On constant run models, remove upper tubing from unloader cylinder.

A2. Remove cylinder head to expose valve assembly.

A3. Remove valve assembly, head to valve package gasket and valve package to cylinder gasket. Use new gaskets in

re-assembly. Note conditions of cylinders, clean out any foreign material and cover with clean shop cloth while open.

A4. Refer to parts breakdown for description of valve package.

A5. Secure valve assembly package, loosen and remove socket head bolts to separate the upper and lower valve seats.

This will expose the valve springs and valve plates.

CAUTION: Do not interchange upper and lower valve seats

A6. Thoroughly clean and wash all valve seats and parts with a suitable non-flammable cleaning fluid.

CAUTION: Use care to not scratch or deform valve parts in the cleaning.

A7. Carefully inspect the valve seats, plates and springs for dents, cracks, wear, and any reason to prevent proper and

efficient operation.

A8. Replace all parts not in proper condition.

Assemble valve assembly package.

B1. Secure lower valve plate in flat position with spring slots “up”.

B2. Refer to parts breakdown for valve package breakdown.

B3. Place valve springs and valve plates in proper positions over slots in seat. Use tag wire or string for tie to hold in

position for completing assembly.

B4. Secure upper valve seat in flat position with spring slots up

B5. Use new valve seat gasket.

B6. Place valve seat gasket in position on lower valve plate.

B7. Place upper valve seat with valve springs and plates tied in position on top of lower valve seat with new valve seat

gasket in place between the two seats.

B8. Start center and then two end valve plates socket head bolts, tighten finger tight being careful not to damage seat

gasket, use socket head wrench to torque the three bolts uniformly to secure the top valve seat to the lower valve

seat using care to avoid damage to the gasket, and valve springs and plates from moving out of position.

B9. Remove ties to free valve springs and plates

B10. Check to be sure valve springs and valve plates are in proper position and the plates are free to flex when manually

touched with blunt instrument.

Assemble valve assembly package into compressor.

C1. Use new gaskets, valve package to cylinder and cylinder head to valve package. Select gaskets by part numbers

from parts breakdown.

C2. Remove shop cloth to expose open cylinder bores. Remove any foreign matter from cylinder bores and top of

cylinder.

C3. Place gasket on top of cylinder, place and align valve package, place gasket on top of valve package and align holes

for head bolts.

C4. Place clean head on top of valve package with gasket and align with cylinder bolt holes.

C5. Insert cylinder head bolts using care to avoid damage to the gaskets, start each bolt threading evenly to contact head

surfaces.

C6. Torque head bolts equally, follow torque specifications on page 20.

C7. Attach and tighten copper tubing of constant running compressors.

C8. Assemble and tighten discharge tubing.

C9. Check oil level in crankcase

C10. Close and tighten valve or the connections used to drain air pressure from system.

C11. Remove all tools and make area safe to start compressor.

C12. Turn on power at main switch and inspect to see that unit is operating properly.

C13. Stay with unit for normal pump up to cut out pressure.

C14. If unit has performed through a running cycle properly put on line for duties and remove red tag from power supply

switch.

C15. Make entry in equipment maintenance log.

CAP-600

31

VALVE PLATES DESIGNS FOR E-57 COMPRESSOR

CAP-600

32

TORQUE

CM-FT.

225-16.3

225-16.3

225-16.3

225-16.3

225-16.3

320-23.1

320-23.1

225-16.3

M10-1.5

M8-1.25

INLET & OUTLET

VALVE PUSH COVERS

SIZE

BOLT

M8-1.25

M8-1.25

M8-1.25

M8-1.25

M8-1.25

M10-1.5

L

H

TORQUE

CM-FT.

100-6.8

100-6.8

100-6.8

180-13.0

180-13.0

180-18.0

180-13.0

280-20.25

300-21.7

280-20.25

280-20.25

300-21.7

280-20.25

280-20.25

28-120.25

280-20.25

REAR COVER

SIZE

BOLT

M6-1

M6-1

M6-1

M8-1.25

M8-1.25

M8-1.25

M8-1.25

M10-1.5

M8-1.25

M10-1.5

M10-1.5

M8-1.25

M10-1.5

M10-1.5

M10-1.5

M10-1.5

TORQUE

CM-FT.

100-6.8

180-13.0

100-6.8

180-13.0

180-13.0

180-13.0

180-13.0

280-20.25

180-13

280-20.25

280-20.25

300-21.7

300-21.7

300-21.7

320-23.11

320-23.1

FRONT COVER

SIZE

BOLT

M6-1

M8-1.25

M6-1

M8-1.25

M8-1.25

M8-1.25

M8-1.25

M10-1.5

M8-1.25

M8-1.5

M8-1.5

M10-1.5

M8-1.5

M8-1.5

M10-1.5

M10-1.5

TORQUE

CM-FT.

135-9.7

180-13.0

135-9.7

180-13.0

180-13.0

180-13.0

180-13.0

280-20.25

180-13

280-20.25

280-20.25

280-20.25

300-21.7

300-21.7

320-23.1

320-23.1

ROD BOLTS

SIZE

BOLT

M6-1

M8-1.25

M6-1

M8-1.25

M8-1.25

M8-1.25

M8-1.25

M10-1.5

M8-1.25

M8-1.5

M8-1.5

M8-1.25

M8-1.5

M8-1.5

M10-1.5

M10-1.5

TORQUE

CM-FT.

200-14.5

120-8.7

200-14.5

200-14.5

200-14.5

200-14.5

280-20.25

200-14.5

280-20.25

280-20.25

280-20.25

280-20.25

280-20.25

350-25.3

350-25.3

CYLINDER-CASE

SIZE

BOLT

M8-1.25

M6-1

M8-14.5

M8-1.25

M8-1.25

M8-1.25

M10-1.5

M8-1.25

M10-1.5

M10-1.5

M10-1.5

M10-1.5

M10-1.5

M10-1.75

M10-1.75

TORQUE

CM-FT.

120-8.7

200-14.5

120-8.7

200-14.5

200-14.5

200-14.5

200-14.5

300-21.7

200-14.5

300-21.7

300-21.7

320-23.1

320-23.1

320-23.1

320-23.1

320-23.1

HEAD BOLTS

SIZE

BOLT

M6-1

M8-1.25

M6-1

M8-1.25

M8-1.25

M8-1.25

M8-1.25

M10-1.5

M8-1.25

M10-1.5

M10-1.5

M10-1.5

M10-1.5

M10-1.5

M10-1.5

M10-1.5

BOLT TORQUES FOR CHALLENGE AIR COMPRESSORS

ES03

ES05

ES06

ES10

E11

ES20

E23

ES30

E35

ES50

E50

E57

ES100

E71

ES150

E15

CAP-600

33

BOLT TORQUES

FLYWHEEL BOLTS FAN BOLTS

MODEL

NO. TORQUE

FT.-LBS. TORQUE

IN.-LBS. TORQUE

FT.-LBS. TORQUE

IN.-LBS.

ES03 8 96 - -

ES05

ES06

ES10

E11

ES20

E23

E35

12 144 - -

E57 23 276 - -

ES30 30 360 - -

ES50

E50 40 480 - -

E71

ES100 45 540 24 288

E15

ES150 50 600 24 288

CAP-600

34

OIL CAPACITIES

MODEL

NUMBER HORSEPOWER MIN

RPM OIL CAPACITY

ES03 1/4 – 1/2 500 1/2 PINTS

ES05 1/2 500 1/2 PINTS

ES06 3/4 500 10 OUNCES

ES10 1 500 1¼ PINTS

ES20 2 – 3 500 1¾ PINTS

ES30 3 – 5 500 1¼ PINTS

ES50 5 – 7½ 500 1½ QUARTS

ES100 7½ - 10 500 2½ QUARTS

ES150

ES150A 15 500 5 QUARTS

E11 1 500 1¼ PINTS

E23 2 – 3 500 1¾ PINTS

E35 3 – 5 500 2½ PINTS

E50 5 500 1½ QUARTS

E57 5 – 7½ 500 2 QUARTS

E71 10 500 2½ QUARTS

E15 15 500 5 QUARTS

CAP-600

35

TROUBLESHOOTING

SYMPTOMS CAUSES REMEDIES

Flywheel rotation in wrong direction Incorrect connection of motor terminal Re-arrange terminal connection.

Overheating of bearings 1. Insufficient lubrication.

2. Bad lubrication system.

3. Crankshaft bearings to tight.

1. Add lubrication oil.

2. Remove and examine the system.

3. Readjust load on bearings.

Flywheel rotation slows down 1. Heavy lubrication oil.

2. Drop in voltage.

3. Belts slipping.

1. Refill with lighter lubrication oil.

2. Contact power company or install

a transformer.

3. Tighten belts

Severe vibration Bent crankshaft Remove & Replace

Abnormal noise 1. Loose valve assembly.

2. Piston hits cylinder cover.

3. Worn connecting rod bearing.

1. Tighten valve bolt and lock nut.

2. Check piston & rod assembly for

excessive wear.

3. Replace bearing.

Pressure cannot be built up or only

up to a certain extent 1. Worn valve plate.

2. Valve springs have lost their

temper.

3. Dirt on the valve plate.

4. Leaks from safety valve.

5. Leaks from bolt holes.

6. Uneven valve seat surface.

7. Excessive blow by on piston rings.

8. Bad packing (gasket to thick).

9. Excessive air leaks.

1. Repair or replace valve plate.

2. Replace valve springs.

3. Remove and clean it.

4. Repair or replace safety valve.

5. Tighten the nuts even with

packing.

6. Remove and lap the surface.

7. Replace with new ones

8. Replace packing (gasket).

9. Eliminate air leaks.

Inaccuracy of pressure gauge Pressure gauge damaged. Replace.

Excessive oil consumption 1. Worn piston ring

2. Worn piston.

3. Worn cylinder.

1. Replace.

2. Replace.

3. Replace.

Slipping of belts 1. Working pressure too high.

2. Improper belt tension.

3. Worn belt.

1. Lower working pressure.

2. Adjust belt tension.

3. Replace with new ones.

WHEN COMPRESSOR CAN BE STARTED

Overheating of electric motors 1. Overloading of motor due to

excessive working pressure

(higher than stipulated pressure).

2. Burnt piston.

3. Burnt bearing metals.

4. Drop of voltage.

1. Lower working pressure.

2. Rebuild compressor.

3. Rebuild compressor.

4. Contact power company or install

a transformer

Unit will not start 1. Breakdown of electric current.

2. Line failure.

3. Malfunction of motor

1. Contact power company.

2. Examine the line. Replace with

new wiring.

3. Contact motor manufacturer.

WHEN COMPRESSOR

CANNONT BE STARTED

Fuse tends to blow 1. Incorrect size.

2. Wrong connections

3. Overloading of motor.

4. Overloading of motor due to leaks

of outlet valve.

5. Crankshaft too tight.

1. Replace with correct size.

2. Change connections.

3. Eliminate the loading.

4. Remove and repair outlet valve.

5. Remove crankshaft and examine

it for cause.

CURTIS-TOLEDO CUSTOMER SERVICE (314) 383-1300

CAP-600

36

RECOMMENDED STATEMENT ON DRYERS AND FILTERS

Liquid water occurs naturally in air lines as a result of compression. Moisture

vapor in ambient air is concentrated when pressurized and condenses when cooled in

downstream air piping.

Compressed air dryers reduce water vapor concentration and prevent liquid

water formation in compressed air lines. Dryers are necessary companion to air filters,

aftercoolers, and automatic tank drains for improving the productivity of compressed air

systems.

Water and water vapor removal increases the efficiency of air operated

equipment, reduces contamination and rusting, increases service life of pneumatic

equipment and tools, prevents air line freeze ups, and reduces product rejects. The use

of dryer’s filters is recommended when this moisture related problems are reported to

our factory or distributor service departments.

Troubleshooting guide

Symptom: Liquid water present in compressed air lines.

Problem: Water vapor condensation from cooling and

compression occurs naturally

Solution: Remove the water vapor from compressed air prior to

distribution through the air system. Check operation of

after-cooler and moisture separator. Install a compressed

air dryer sized for the flow and dryness level required.

(Note: filters may also be required to remove

particles, liquid oil aerosols, or for oil vapor removal.

Change cartridges as recommended by filter manufacturer.)

Check all drain traps routinely to insure their proper operation.

Maintain them regularly.

CAP-600

37

COMPRESSOR PUMP-UP TIME

TWO STAGE Tank size Approx. Time Required

To Pump From:

H.P.

Size Compressor

Model No. R.P.M.

Piston

Displ.

C.F.M. Size

(in) Gal 0 to 175 PSIG

Min. – Sec. 145 to 175 PSIG

Min. – Sec.

3 3VT6 947 10.66 20 x 50 60 12’ – 24” 2’ – 8”

5 5E23VT6 1000 11.3 20 x 50 60 11’ – 47” 2’ – 1”

5 5E1HT6 1100 15.81 20 x 50 60 7’ – 46” 1’ – 20”

5 5E1VT6 1100 15.81 20 x 50 60 7’ – 46” 1’ – 20”

5 5E1HT8 1100 15.81 20 x 48 80 10’ – 21” 1’ – 46”

5 5E1VT8 1100 15.81 20 x 48 80 10’ – 21” 1’ – 46”

5 5HT6 968 20.58 20 x 50 60 5’ – 56” 1’ – 1”

5 5VT6 968 20.58 20 x 50 60 5’ – 56” 1’ – 1”

5 5HT8 968 20.58 20 x 66 80 7’ – 54” 1’ – 21”

5 5VT8 968 20.58 20 x 48 80 7’ – 54” 1’ – 21”

5 5E2HT6 900 21.47 20 x 50 60 5’ – 25” 0’ – 56”

5 5E2VT6 900 21.47 20 x 50 60 5’ – 25” 0’ – 56”

5 5E2HT8 900 21.47 20 x 66 80 7’ – 14” 1’ – 14”

5 5E2VT8 900 21.47 20 x 48 80 7’ – 14” 1’ – 14”

7 1/2 7E2HT8 1100 26.24 20 x 66 80 6’ – 16” 1’ – 05”

7 1/2 7E2VT8 1100 26.24 24 x 48 80 6’ – 16” 1’ – 05”

7 1/2 7HT8 764 29.57 20 x 66 80 5’ – 22” 0’ – 55”

10 10HT8 977 37.81 20 x 66 80 4’ – 11” 0’ – 43”

10 10HT12 977 37.81 24 x 70 120 6’ – 17” 1’ – 5”

10 10VT12 977 37.81 30 x 47 120 6’ – 17” 1’ – 5”

15 15HT12 855 54.55 24 x 70 120 4’ – 28” 0’ – 46”

TWO STAGE GASOLINE ENGINE DRIVEN Tank size Approx. Time Required

To Pump From:

H.P.

Size Compressor

Model No. R.P.M.

Piston

Displ.

C.F.M. Size

(in) Gal 0 to 175 PSIG

Min. – Sec. 145 to 175 PSIG

Min. – Sec.

10 10E2GT3 910 21.7 16 x 41 30 2’ – 42” 0’ – 28”

10 10GT3 950 20.2 16 x 41 30 3’ – 1” 0’ – 31”

10 10GT6 950 20.2 20 x 50 60 6’ – 3” 1’ – 2”

13 13E2GT3K 910 21.7 16 x 41 30 2’ – 42” 0’ – 28”

13 13GT3K 950 20.2 16 x 41 30 3’ – 1” 0’ – 31”

13 13GTGK 950 20.2 20 x 50 60 6’ – 3” 1’ – 2”

13 13E2GT3HE 910 21.7 16 x 41 30 2’ – 42” 0’ – 28”

CAP-600

38

COMPRESSOR PUMP-UP TIME

SINGLE STAGE Tank size Approx. Time Required

To Pump From:

H.P.

Size Compressor

Model No. R.P.M.

Piston

Displ.

C.F.M. Size

(in) Gal 0 to 100 PSIG

Min. – Sec. 80 to 100 PSIG

Min. – Sec.

3 3HS6 945 15.97 20 x 50 60 6’ – 16” 1’ – 15”

3 3VS6 945 15.97 20 x 50 60 6’ – 16” 1’ – 15”

5 5ES20VS6 1000 16.9 20 x 50 60 6’ – 4” 1’ – 13”

5 5HS6 945 20.13 20 x 50 60 4’ – 8” 0’ – 50”

5 5VS6 945 20.13 20 x 50 60 4’ – 8” 0’ – 50”

5 5HS6 945 20.13 20 x 66 80 5’ – 31” 1’ – 6”

5 5VS8 945 20.13 24 x 48 80 5’ – 31” 1’ – 6”

7 1/2 7HS8 945 30.14 20 x 66 80 3’ – 35” 0’ – 43”

7 1/2 7VS8 945 30.14 24 x 48 80 3’ – 35” 0’ – 43”

10 10HS8 866 50.4 20 x 66 80 2’ – 7” 0’ – 25”

10 10HS12 866 50.4 24 x 70 120 3’ – 10” 0’ – 38”

10 10VS12 866 50.4 30 x 47 120 3’ – 10” 0’ – 38”

15 15HS12 855 81.74 24 x 70 120 2’ – 2” 0’ – 24”

CAP-600

NOTES

39

CURTIS – TOLEDO, INC.

1905 KIENLEN AVE., ST. LOUIS, MO 63133

TEL. (314) 383-1300 FAX (314) 381-1439

E-MAIL: CURTISCOMP@AOL.COM