DPS 5000+ Instr Manual 5000

DPS-5000+ instr manual DPS-5000+ instr manual

User Manual: DPS-5000+ Manual

Open the PDF directly: View PDF PDF.
Page Count: 1

Item No.
DPS-5000 / DPS-5000-C
One Hour Rechargeable Battery Kit
This Charger is controlled by intelligent MCU and designed to
charge Nickel Metal Hydride AA and AAA size rechargeable
batteries. Please note that this charger must not be used for
Alkaline, Carbon Zinc, Lithium or any kind of battery other than
Nickel Metal Hydride (NiMH).
Features:
l Charging is controlled by a special intelligent MCU which
supplies optimal charging current to prolong battery cycle
life and accelerate charging speed.
l Switching mode adaptor could accept worldwide AC power
source (Input: AC 100V-240V 50/60Hz) and is suitable for
global travel.
l Recharges 2 or 4 pieces AA or 2 pieces AAA Ni-MH
batteries at a time.
l Special design to keep the same charging current while
charging 2 or 4 batteries.
l Automatic charging current selection for size AA & AAA.
l LED display for rapid charge / trickle charge / bad cell
detection (see instructions).
Safety features:
l -dV cut off function
l Maximum temperature cut off function
l Maximum voltage cut off function
l Safety timer cut off function
l Reverse-polarity protection
Instructions:
Step 1. Loading batteries into charger:
A. Place batteries in the charger as per the”+” “-“ indication.
B. For Charging 4 pieces AA batteries, place 4 AA batteries in
the charger and slide the battery number button to the “4”
position (Fig.1).
C. For charging 2 batteries, place 2 AA or AAA batteries in the
middle two channels and slide the battery number button to the
“2” position (Fig.2).
Step 2. Plugging in the charger:
A. For DC power, connect the DC Adaptor plug to your
DIGIPOWER charger and plug into DC outlet.
B. For AC power, connect the AC Adaptor plug to your
DIGIPOWER charger and plug into AC outlet. ( Input
voltage: AC100V-240V, 50/60Hz ).
Step 3. Charging and LED indicators:
A. The Green LED stays lit to indicate charger is powered on.
B. Flashing Red LED indicates the batteries are charging
C. Solid Red LED indicates batteries are fully charged.
D. If charger is plugged in and there is No Red LED on, then
charger is in default mode (see Notes below).
Note:Charge time may vary with battery make and / or capacity:
Notes:
The charger will not supply charging current under default mode.
The default mode could be due any of the following cases:
A. No batteries were placed in charger.
B The “2/4” optional button is not in the correct position.
C. Battery(s) are placed in charger with reverse-polarity ( + - ).
D. AA and AAA batteries are mixed.
E. Non – NiMH batteries are placed in charger.
Important Safety Instructions:
1. Before charging, read instructions.
2. This charger is designed for indoor use only, do not expose
to dampness or rain.
3. This charger is intended to charge AA or AAA
Nickel-Metal-Hydride (NiMH) rechargeable batteries only.
Attempting to charge any other types of batteries may cause
personal injury and damage.
4. Do not charge AA and AAA batteries together.
5. Do not charge Alkaline or non - Ni-MH batteries.
6. Do not charge different capacity batteries together.
Recharge only one type of battery at each time.
7. Remove AC or DC adaptors from outlets when not in use.
8. Unplug the charger from outlet before attempting any
maintenance or cleaning.
ONE YEAR WARRANTY:
Mizco International, Inc., warrants this product to be free from defects in
materials and workmanship to the original purchaser for a period of ONE
YEAR from the original date of purchase. Mizco’s responsibility with
regard to this limited warranty shall be limited solely to the repair or
replacement, at its own option, of any product, which fails during normal
use. This warranty does not extend to damage or failure, which results
from misuse, neglect, accident or alteration, abuse, improper installation,
or improper maintenance. To exercise this limited warranty, send your
name and address with proof of purchase and the UPC from this package.
Product sent for warranty must be mailed to the address below, freight
prepaid. Include $5.00 for return shipping and handling.
DIGIPOWER
140 58th Street
Bldg B, Unit 1F
Brooklyn, NY 11220
e-mail: digipowersolutions@mizco.com
©2002 Mizco International, Inc. All rights reserved. Digipower
is a registered trademark of Mizco Int’l, Inc. All trade names are
trademarks of their respective manufacturers .
Fig.1 Fig.2

Navigation menu