DRV2700EVM User's Guide (Rev. C) DRV2700 EVA Manual

User Manual:

Open the PDF directly: View PDF .
Page Count: 35

DRV2700EVM High Voltage Piezo Driver Evaluation Kit
10 Trademarks
Revision History
Revision History
Revision History
Important Notice

SLOU403C–March 2015–Revised June 2018

DRV2700EVM High Voltage Piezo Driver Evaluation Kit

User's Guide

SLOU403C–March 2015–Revised June 2018

DRV2700EVM High Voltage Piezo Driver Evaluation Kit

The DRV2700 is a single-chip, high-voltage piezo driver with an integrated 105-V boost switch, integrated

power diode, and integrated fully differential amplifier. This evaluation kit demonstrates:

• Multiple input modes including: 0- to 10-V single ended, PWM, and AC input modes

• Multiple output modes including: 0- to 200-Vpp differential, 0- to 105-V single and multiple ended

• 2 power supply inputs to isolate power consumption on DRV2700

• 8 convenient boost voltage settings and 4 different gain settings

• Small footprint (9 mm x 13 mm)

• Breakout for usage as a boost converter

The evaluation kit is designed for all-around use and can be used not only for evaluation but can also be

used for prototyping into systems. The EVM also contains a microcontroller, LDO (3.3 V) and LEDs for

status and input settings.

Evaluation Kit Contents:

• DRV2700EVM evaluation board

• Demonstration mode firmware preloaded onto microcontroller

• Downloadable software to control EVM

• Mini-B USB cable

Needed for programming and advanced configuration:

• Code Composer Studio™ (CCS) or IAR Embedded Workbench IDE for MSP430

• MSP430 LaunchPad™ (MSP-EXP430G2) or MSP430-FET430UIF hardware programming tool

• DRV2700EVM firmware available on the DRV2700EVM tool folder

• MSP-JTAG2SBW JTAG to Spy-Bi-Wire adapter

www.ti.com

2SLOU403C–March 2015–Revised June 2018

Submit Documentation Feedback

DRV2700EVM High Voltage Piezo Driver Evaluation Kit

Contents

1 Getting Started ............................................................................................................... 6

1.1 Evaluation Module Operating Parameters....................................................................... 6

1.2 Quick Start Board Setup ........................................................................................... 7

1.3 Connecting a Load.................................................................................................. 7

2 Overview of EVM ............................................................................................................ 8

2.1 DRV2700............................................................................................................. 8

2.2 Microcontroller (MSP430).......................................................................................... 8

2.3 Power Supply Inputs and Path.................................................................................... 8

2.4 EN and Gain Configuration........................................................................................ 9

2.5 Inputs ............................................................................................................... 10

2.6 Outputs ............................................................................................................. 10

2.7 BST/PVDD Disconnect ........................................................................................... 10

2.8 TRIG Button........................................................................................................ 10

3 EVM Control Software (GUI).............................................................................................. 11

4 Boost Converter ............................................................................................................ 12

4.1 Boost Voltage Setting Resistors................................................................................. 13

4.2 Disconnecting BST/PVDD........................................................................................ 14

4.3 Programming the Boost Current Limit .......................................................................... 14

4.4 Boost Inductor Selection ......................................................................................... 14

4.5 Boost Capacitor Selection........................................................................................ 14

5 PWM, Analog, and Single-Ended Inputs ................................................................................ 15

5.1 PWM (AC Coupled) Input Using MSP430 ..................................................................... 15

5.2 PWM (AC Coupled) Input Using AIN ........................................................................... 15

5.3 External Analog (AC Coupled) Input............................................................................ 16

5.4 Single-Ended (DC Coupled) Input .............................................................................. 16

6 Output........................................................................................................................ 19

6.1 Two Terminal Differential Output Configuration (OUT+ – OUT–)........................................... 19

6.2 Two Terminal Single Ended Output Configuration (OUT± to BST/GND) .................................. 19

6.3 Three Terminal Single Ended Output Configuration (BST to OUT± to GND) ............................. 20

7 Load Selection.............................................................................................................. 20

8 Filtering and Adapting PWM Waveforms................................................................................ 21

8.1 PWM Input ......................................................................................................... 21

8.2 Filter Selection Criteria ........................................................................................... 22

9 Reference ................................................................................................................... 25

9.1 Schematic .......................................................................................................... 25

9.2 PCB Layout ........................................................................................................ 26

9.3 Bill of Materials .................................................................................................... 28

List of Figures

1 Board Diagram ............................................................................................................... 6

2 Power Path Diagram ........................................................................................................ 8

3 Gain = 40.7 dB ............................................................................................................... 9

4 Gain = 38.4 dB ............................................................................................................... 9

5 Gain = 34.8 dB ............................................................................................................... 9

6 Gain = 28.8 dB ............................................................................................................... 9

7 GUI Interface................................................................................................................ 11

8 BST Network JP2, JP3, and JP4......................................................................................... 13

9 PWM Signal................................................................................................................. 15

10 Set Reference to External 2.5 V ......................................................................................... 17

11 Floating Reference at 3 Hz and No Load ............................................................................... 17

12 Floating Reference at 1 Hz and No Load ............................................................................... 17

13 DC Coupled Input Diagram ............................................................................................... 18

www.ti.com

SLOU403C–March 2015–Revised June 2018

DRV2700EVM High Voltage Piezo Driver Evaluation Kit

14 Two Terminal Differential Output......................................................................................... 19

15 Two Terminal Single Ended Output ..................................................................................... 19

16 Three Terminal Single Ended Output ................................................................................... 20

17 DRV2700EVM First- and Second-Order Filters ........................................................................ 21

18 Differential, First-Order Filter ............................................................................................. 22

19 Frequency Response of the First-Order Filter.......................................................................... 22

20 Differential, Second-Order Filter ......................................................................................... 23

21 Frequency Response of the Second-Order Filter...................................................................... 23

22 DRV2700EVM Schematic................................................................................................. 25

23 All Layers.................................................................................................................... 26

24 Top Layer ................................................................................................................... 26

25 Mid Layer 1 ................................................................................................................. 27

26 Mid Layer 2 ................................................................................................................. 27

27 Bottom Layer................................................................................................................ 28

WARNING

EXPORT NOTICE

Recipient agrees to not knowingly export or re-export, directly or

indirectly, any product or technical data (as defined by the U.S.,

EU, and other Export Administration Regulations) including

software, or any controlled product restricted by other applicable

national regulations, received from Disclosing party under this

Agreement, or any direct product of such technology, to any

destination to which such export or re-export is restricted or

prohibited by U.S. or other applicable laws, without obtaining prior

authorization from U.S. Department of Commerce and other

competent Government authorities to the extent required by those

laws. This provision shall survive termination or expiration of this

Agreement. According to our best knowledge of the state and end-

use of this product or technology, and in compliance with the

export control regulations of dual-use goods in force in the origin

and exporting countries, this technology is classified as follows:

US ECCN: 3E991

EU ECCN: EAR99

And may require export or re-export license for shipping it in

compliance with the applicable regulations of certain countries.

www.ti.com

4SLOU403C–March 2015–Revised June 2018

Submit Documentation Feedback

DRV2700EVM High Voltage Piezo Driver Evaluation Kit

Cautions and Warnings

CAUTION:

Warning! Do not leave EVM powered when unattended.

HOT SURFACE:

Warning Hot Surface! Contact may cause burns. Do not touch. Please take the proper

precautions when operating.

HIGH VOLTAGE:

Danger High Voltage! Electric shock possible when connecting board to live wire. Board should

be handled with care by a professional. For safety, use of isolated test equipment with

overvoltage/overcurrent protection is highly recommended.

WARNING

www.ti.com

SLOU403C–March 2015–Revised June 2018

DRV2700EVM High Voltage Piezo Driver Evaluation Kit

General Texas Instruments High Voltage Evaluation (TI HV EVM) User Safety Guidelines

Always follow TI’s setup and application instructions, including use of all interface components within their

recommended electrical rated voltage and power limits. Always use electrical safety precautions to help

ensure your personal safety and those working around you. Contact TI's Product Information Center

http://support/ti./com for further information.

Save all warnings and instructions for future reference.

Failure to follow warnings and instructions may result in personal injury, property damage, or

death due to electrical shock and burn hazards.

The term TI HV EVM refers to an electronic device typically provided as an open framed, unenclosed

printed circuit board assembly. It is intended strictly for use in development laboratory environments,

solely for qualified professional users having training, expertise and knowledge of electrical safety

risks in development and application of high voltage electrical circuits. Any other use and/or

application are strictly prohibited by Texas Instruments. If you are not suitable qualified, you should

immediately stop from further use of the HV EVM.

1. Work Area Safety

1. Keep work area clean and orderly.

2. Qualified observer(s) must be present anytime circuits are energized.

3. Effective barriers and signage must be present in the area where the TI HV EVM and its interface

electronics are energized, indicating operation of accessible high voltages may be present, for the

purpose of protecting inadvertent access.

4. All interface circuits, power supplies, evaluation modules, instruments, meters, scopes and other

related apparatus used in a development environment exceeding 50Vrms/75VDC must be

electrically located within a protected Emergency Power Off EPO protected power strip.

5. Use stable and nonconductive work surface.

6. Use adequately insulated clamps and wires to attach measurement probes and instruments. No

freehand testing whenever possible.

2. Electrical Safety

As a precautionary measure, it is always a good engineering practice to assume that the entire EVM

may have fully accessible and active high voltages.

1. De-energize the TI HV EVM and all its inputs, outputs and electrical loads before performing any

electrical or other diagnostic measurements. Revalidate that TI HV EVM power has been safely

de-energized.

2. With the EVM confirmed de-energized, proceed with required electrical circuit configurations,

wiring, measurement equipment connection, and other application needs, while still assuming the

EVM circuit and measuring instruments are electrically live.

3. After EVM readiness is complete, energize the EVM as intended.

WARNING: WHILE THE EVM IS ENERGIZED, NEVER TOUCH THE EVM OR ITS ELECTRICAL

CIRCUITS AS THEY COULD BE AT HIGH VOLTAGES CAPABLE OF CAUSING ELECTRICAL

SHOCK HAZARD.

3. Personal Safety

1. Wear personal protective equipment (for example, latex gloves or safety glasses with side shields)

or protect EVM in an adequate lucent plastic box with interlocks to protect from accidental touch.

Limitation for safe use:

EVMs are not to be used as all or part of a production unit.

Getting Started

www.ti.com

6SLOU403C–March 2015–Revised June 2018

Submit Documentation Feedback

DRV2700EVM High Voltage Piezo Driver Evaluation Kit

1 Getting Started

The DRV2700EVM is designed for flexible use for prototyping as well as evaluation. Figure 1 shows the

names and locations of the various elements on the EVM. To power the board, connect the DRV2700EVM

to an available USB port on your computer using a mini-B USB cable. The default board settings cause

the microcontroller (MSP430) to control the inputs of the DRV2700 at power up. The MSP430 has each of

these control settings low which disables the DRV2700, by default. Figure 1 shows the basic board

diagram of the DRV2700EVM. Table 2 shows the original configuration of the jumpers, as shipped.

Figure 1. Board Diagram

1.1 Evaluation Module Operating Parameters

Table 1 lists the operating conditions for the DRV2700 on the evaluation module.

Table 1. Typical Operating Conditions

Parameter Specification

Supply voltage range 3.6 V to 5.5 V

Power-supply current rating 500 mA

Input Voltage 0 V to VDD

Max Output Voltage 200 Vpp

www.ti.com

Getting Started

SLOU403C–March 2015–Revised June 2018

DRV2700EVM High Voltage Piezo Driver Evaluation Kit

1.2 Quick Start Board Setup

The DRV2700EVM comes with preprogrammed firmware to provide a 0- to 200-Vpp signal between OUT+

and OUT–.

1. Out of the box, the jumpers are set to begin demo mode using USB power. The default jumper settings

are found in Table 2.

2. Connect a mini-USB cable to the USB connector on the DRV2700EVM board.

3. Connect the other end of the USB cable to an available USB port on a computer, USB charger, or USB

battery pack.

4. If the board is powered correctly, the 5-V LED is on.

5. Enable the output using the GUI or programmatically through the computer, see GUI Interface for

additional assistance. If using an external input signal, EN the output by changing the jumper (JP9) or

equivalent control signal.

6. Once the output is EN, the device allows for the high-voltage output.

(1) In the table, (top) or (bottom) means the (top) or (bottom) is connected to the middle of the 3-terminal header. For questions,

refer to Figure 1.

Table 2. Default Jumper Settings

Parameter Jumper Setting Default Specification

JP10 MSP

Open MSP not connected to either power supply

USB (top)(1) X MSP connected to USB power supply

VIN (bottom)(1) MSP connected to VIN power supply

JP11 DRV

Open DRV2700 not connected to either power supply

VIN (top)(1) DRV2700 connected to VIN power supply

USB (bottom)(1) X DRV2700 connected to USB power supply

JP5 and JP6 Open Disconnected PWM± and I/O of MSP430

Connected X Connected PWM± and I/O of MSP430

JP9-EN

JP8-G1

JP7-G0

Open EN/G1/G0 pulled internally to GND through DRV2700 internal resistance

MSP (top)(1) X EN/G1/G0 tied to I/O of MSP430

PU (bottom)(1) EN/G1/G0 pulled up to MSP power supply through external pull up resistor

JP13-DCIN Open X DC input not connected (PWM and AC input mode)

Connected DC input connected (single-ended input mode)

JP12-VBST Open PVDD disconnected to BST (boost only mode)

Connected X PVDD connected to BST (normal operation)

I2C Open Always leave open. Never jumper together.

J2, J3, J4 Open Disconnects particular FB resistor (lowers BST)

Connected X Connects particular FB resistor (raises BST)

1.3 Connecting a Load

1. With the power supply off, connect the negative terminal of the load to OUT– and connect the positive

terminal of the load to OUT+

2. Ensure the terminals are connected correctly, then enable the supply

WARNING

Before connecting the load, ensure that the load is rated for the

selected output voltage. If not, see the Boost Voltage Setting

Resistors section to adjust the DRV2700 maximum output voltage.

See Figure 13 for a diagram of the input configuration.

USB

Power

VIN

External

MSP HeaderDRV Header

Power to Rest of Board

Power to DRV2700

Overview of EVM

www.ti.com

8SLOU403C–March 2015–Revised June 2018

Submit Documentation Feedback

DRV2700EVM High Voltage Piezo Driver Evaluation Kit

2 Overview of EVM

The following sections provide a description of each of the blocks identified in Figure 1.

2.1 DRV2700

The DRV2700 is a single-chip, high-voltage piezo driver with an integrated 105-V boost switch, integrated

power diode, and integrated fully-differential amplifier. This EVM allows the designer to evaluate this

device and appropriately prototype it into their design. See the DRV2700 (SLOS861) datasheet for more

in-depth information.

2.2 Microcontroller (MSP430)

An onboard MSP430F5510 is used to control the various input signals as well as communicate through

the USB to the GUI. See the Quick Start Board Setup section for how to setup and run with the GUI.

2.3 Power Supply Inputs and Path

Two power supply inputs are available to power the EVM: USB power and VEXTERNAL (Ext VIN on the EVM).

Each of these inputs can be used to power the entire board or parts of the board.

2.3.1 USB Power Input

The USB power input can be supplied from a standard USB port on a computer, USB charger, or USB

battery pack. This input is intended for ease-of-use and can be routed to power all circuitry on the EVM.

Additionally, this input has a 5-V LED indicator showing that power is being supplied to the EVM. If the

GUI is going to be used, the USB must be connected to the computer and JP10 routed to USB

connection.

2.3.2 VIN/External Power Input

Provide the VIN power input with an external 3.6- to 5.5-V power supply. Additionally, this input can power

the entire board.

2.3.3 Power Path Selection

Each of the two power supply inputs can be routed to the DRV2700 or the rest of the IC. The positions of

the jumpers are described in Table 2 or can be read from the silkscreen of the EVM. Figure 2 shows the

basic diagram of the power paths.

Figure 2. Power Path Diagram

If a power measurement of the DRV2700 circuitry is desired, it is best to provide the MSP jumper (JP10)

with USB power and the DRV jumper (JP11) with VIN. With this configuration, measuring the provided

voltage and current into VIN gives the power consumption of the DRV2700.

www.ti.com

Overview of EVM

SLOU403C–March 2015–Revised June 2018

DRV2700EVM High Voltage Piezo Driver Evaluation Kit

2.4 EN and Gain Configuration

The EN, GAIN0, and GAIN1 inputs into the DRV2700 have 4 different driving configurations:

• Driven through the MSP430. This is done by connecting the configuration jumper to the “MSP” state

(default).

• Pulled to a logic level high through pullup resistor. This is done by connecting the configuration jumper

to the “PU” state.

• Pulled to a logic level low through internal pulldown resistor. This is done by removing the configuration

jumper.

• Driven externally. This is done by connecting the external control signal to the center 100-mil header.

Each of these signals have an LED to indicate when the signal is at a logic-level high.

Additionally, the GAIN pins control the internal gain of the high voltage amplifier. Table 3 shows the 4 gain

settings

Table 3. Gain Settings

GAIN1 GAIN0 Gain (dB)

Low Low 28.8

Low High 34.8

High Low 38.4

High High 40.7

Figure 3 through Figure 6 showcase all 4 gain settings with BST set to max of 105 V (JP2, JP3, and JP4

closed). C3 = BST, C1 = VOUT(+), C2 = VOUT(–), and MATH = OUT(+) – OUT (–). PWM input from

MSP430 of 0–3.3 V, 300 Hz and 50% duty cycle.

Figure 3. Gain = 40.7 dB Figure 4. Gain = 38.4 dB

Overview of EVM

www.ti.com

10 SLOU403C–March 2015–Revised June 2018

Submit Documentation Feedback

DRV2700EVM High Voltage Piezo Driver Evaluation Kit

Figure 5. Gain = 34.8 dB Figure 6. Gain = 28.8 dB

2.5 Inputs

The analog input (AIN) is used for PWM and analog inputs. The single-ended (DC) input test point is used

when a DC input is desired. See PWM, Analog, and Single-Ended Inputs, for more information.

2.6 Outputs

The DRV2700EVM has 4 referenced outputs (BST, OUT–, OUT+, and GND). They are output from a

terminal block to mitigate touching between two high voltage lines. See the Output section for additional

information.

2.7 BST/PVDD Disconnect

The BST jumper (JP12) is provided to allow disconnecting between PVDD and BST. This enables the

DRV2700EVM to be configured purely as a boost converter. See Disconnecting BST/PVDD, for additional

information.

2.8 TRIG Button

The DRV2700EVM has a built-in trigger button for user prototyping. If different modes of operation are

desired without using the GUI, the MSP430 can be programmed such that the trigger button can cycle

through different modes. Additionally, there are 3 test point pads that be can be used in a similar manner

through MSP430 firmware programming.

See Figure 13 for a diagram of the input configuration.

Gain Settings

and Boost Chart

EN Output

Output

Timing

Output

Status

Standard Drive

vs Audio Drive

Frequency

Control

Duty Cycle

Control

Note

and/or

Frequency

Generator

Simple

Piano

www.ti.com

EVM Control Software (GUI)

SLOU403C–March 2015–Revised June 2018

DRV2700EVM High Voltage Piezo Driver Evaluation Kit

3 EVM Control Software (GUI)

By default, the DRV2700EVM can be controlled programmatically through the GUI Interface. Figure 7 is a

screenshot of the GUI.

Run the GUI by downloading it from the DRV2700 product page, installing the GUI and then running it.

When prompted, connect to the USBHID setting.

Figure 7. GUI Interface

Boost Converter

www.ti.com

12 SLOU403C–March 2015–Revised June 2018

Submit Documentation Feedback

DRV2700EVM High Voltage Piezo Driver Evaluation Kit

The GUI is broken up into two sections: Standard Drive and Audio Drive. The Standard Drive utilizes

changing the frequency and duty cycle of the PWM signal and is intended for easy prototyping. The Audio

Drive tab is for showcasing the DRV2700 as a Piezo buzzer/speaker. On both tabs, the sections are

intuitive, however, the following sections are worth describing:

•Gain Settings and Boost Chart: After changing the gain and clicking the Set button, the MSP430

changes the G0 and G1 GPIO therefore changing the gain of the DRV2700. The chart then updates to

reflect the recommended voltage ranges by not highlighting them.

•Output Timing: This button has 3 different modes: Continuous,Pulsed, and Single. These modes help

with a timed EN signal.

•Duty Cycle: This allows control of the power that gets through the DC blocking input filter. Duty Cycle

can be thought of as an amplitude control. Additionally, the PWM signal can be connected through

external wires using JP5 and JP6 headers to IN+ and IN–, in order to control the output.

•Note Generator and Simple Piano: The DRV2700 is capable of also driving piezo loads used in

many alarms and buzzers. To sample this, the simple piano sends the corresponding frequency of the

notes when pressed. If a series of notes and/or frequencies with specific timing is desired, the note

generator can be used in the format of “[Note],[TimeOn],[TimeOff]” as shown in Figure 7. The note

format is A–G (including sharps “#” but not flats “b”) followed by the octave, and the frequency is in Hz

rounded to the nearest integer. Some examples include: A4, C#5, E5 (or 659), and so forth. All time

inputs are based in milliseconds.

See Figure 13 for a diagram of the input configuration.

4 Boost Converter

The DRV2700 device creates a boosted supply rail with an integrated DC-DC converter that can go up to

105 V. The switch-mode power supplies have a few different sources of losses. When boosting to very

high voltages, the efficiency begins to degrade because of these losses. The DRV2700 device has a

hysteretic boost design to minimize switching losses and therefore increase efficiency. A hysteretic

controller is a self-oscillation circuit that regulates the output voltage by keeping the output voltage within a

hysteresis window set by a reference voltage regulator and, in this case, the current-limit comparator.

Hysteretic converters typically have a larger ripple as a trade off because of the minimized switching. This

ripple is a function of the output capacitor, internal delays, and the hysteresis of the control loop. The

power FET and power diode of the boost converter are both integrated within the device to provide the

required switching while minimizing external components. Additionally, the boost voltage output (BST) can

be easily fed into the high-voltage amplifier through the adjacent pin (PVDD) to help minimize routing

inductance and resistance on the board.

Before connecting the load, ensure the load is rated for the current boost voltage setting.

See Boost Voltage Setting Resistors for more information on how to set the boost voltage.

æ ö

= +

ç ÷

BST FB

V V 1

806 lQ

80.6 lQ

49.9 lQ

23.3 lQ

49.9 lQ

JP2JP3JP4

BST

www.ti.com

Boost Converter

SLOU403C–March 2015–Revised June 2018

DRV2700EVM High Voltage Piezo Driver Evaluation Kit

4.1 Boost Voltage Setting Resistors

The boost voltage (BST) is set through a resistor network and through the use of jumpers JP2, JP3, and

JP4 as shown in Figure 8.

Figure 8. BST Network JP2, JP3, and JP4

The boost output voltage is given by Equation 1

(1)

where VFB = 1.32 V and REQ is the equivalent resistor between all the connected resistors in parallel. Refer

to Table 4 for BST setting based on the jumper configuration.

WARNING

Be sure not to hot switch the JP2, JP3, or JP4 connection. This can

be accomplished by only removing or connecting the JP2, JP3, or

JP4 jumpers while the board is unpowered.

Table 4. BST Setting Based on the Jumper Configuration

BST REQ JP2 JP3 JP4

23 V 50 kΩOpen Open Open

37 V 30.8 kΩOpen Open Closed

45 V 25 kΩOpen Closed Open

58 V 19.0 kΩOpen Closed Closed

70 V 15.7 kΩClosed Open Open

83 V 13.2 kΩClosed Open Closed

91 V 12 kΩClosed Closed Open

105 V 10.4 kΩClosed Closed Closed

If another voltage is desired, replace R1 and R5 using Equation 1 and leave JP2–4 disconnected.

REF

EXT INT

LIM

R  K R

æ ö

= -

ç ÷

è ø

Boost Converter

www.ti.com

14 SLOU403C–March 2015–Revised June 2018

Submit Documentation Feedback

DRV2700EVM High Voltage Piezo Driver Evaluation Kit

4.2 Disconnecting BST/PVDD

The DRV2700 has two essential blocks: the boost converter and the amplifier. If only using the

DRV2700’s boost converter, JP_VBST allows the user to disconnect PVDD from BST to shut down the

amplifier to save power.

WARNING

Be sure not to hot switch the BST and PVDD connection. This can

only be accomplished by removing or connecting the JP_VBST

jumper while the board is unpowered.

4.3 Programming the Boost Current Limit

The peak inductor current is set with resistor R3 (REXT). The current limit is not a safety mechanism, but

the highest value current the inductor will see each cycle. The inductor must be capable of handling this

programmed limit during normal operation. The relationship of REXT to ILIM is approximated with

Equation 2 where ILIM is the current limit set by REXT, K = 10500, VREF = 1.35 V and RINT = 60 Ω.

(2)

4.4 Boost Inductor Selection

Inductor selection plays a critical role in the performance of the DRV2700. The range of recommended

inductor values is 3.3 µH to 22 µH. When a larger inductance is chosen, the DRV2700 boost converter

automatically runs at a lower switching frequency and incurs less switching losses; however, the larger

inductors may also have a higher equivalent series resistance (ESR), which will increase the parasitic

inductor losses. Smaller inductances generally have higher saturation currents; therefore, they are better

suited for maximizing the output current of the boost converter. Table 5 lists several sample inductors that

provide adequate performance.

Table 5. Sample Inductors

Manufacturer Part Number DCR (Ω) Inductance (µH) ISAT (A) REXT (Ω) ILIM (A)

Coilcraft LPS4018-332MLB 0.080 3.3 1.9 7.32k 1.9

Coilcraft LPS4018-472MLB 0.125 4.7 1.8 7.5k 1.8

TDK VLS3012T-3R3M1R3 0.100 3.3 1.5 9.31k 1.5

4.5 Boost Capacitor Selection

The boost output voltage may be programmed as high as 105 V. A capacitor must have a voltage rating

equivalent to the boost output voltage or higher. A 250-V rated 100-nF capacitor of X5R or X7R type is

recommended for a boost converter voltage of 105 V. The selected capacitor should have a minimum

derated capacitance of 50 nF.

See Figure 13 for a diagram of the input configuration.

www.ti.com

PWM, Analog, and Single-Ended Inputs

SLOU403C–March 2015–Revised June 2018

DRV2700EVM High Voltage Piezo Driver Evaluation Kit

5 PWM, Analog, and Single-Ended Inputs

The DRV2700 requires a low-pass filtered PWM waveform, an analog signal or a single-ended input to

drive capacitive loads. By default, the DRV2700EVM uses the MSP430 PWM input mode with a low-pass

filter. This section describes each input mode in detail and the modifications necessary for operation of

each. See Filtering and Adapting PWM Waveforms for more details on adapting the PWM waveform using

a low-pass filter.

The DRV2700EVM supports four input modes for driving the DRV2700:

•PWM (AC coupled) input using MSP430: In this mode, the onboard MSP430 generates a PWM

waveform that is sent through the low-pass input filter to the DRV2700.

•PWM (AC coupled) input using AIN: An external source supplies a PWM waveform to the EXTIN

header which is sent through the low-pass input filter to the DRV2700.

•External analog (AC coupled) input: An external source supplies an analog waveform (sine wave) to

the IN+ and IN– header. The low-pass input filter can be removed in this case.

•Single-ended (DC coupled) input: A DC input signal can be used to drive the output in a steady

state.

5.1 PWM (AC Coupled) Input Using MSP430

Figure 9. PWM Signal

When using the DRV2700EVM in MSP430 PWM input mode, the onboard MSP430 generates a

differential PWM signal that is sent through a low-pass filter to the DRV2700. The DRV2700EVM is setup

to use this mode by default. Set to default settings to use this input mode.

If specific waveforms (other than those already on the MSP430) are needed, the firmware can be updated.

To update the firmware, download Code Composer Studio (or a third-party MSP430 IDE) and connect the

DRV2700EVM SpyBiWire to the computer. The TI website offers an MSP430 USB-to-JTAG hardware

interface (MSP-FET430UIF) for updating and debugging MSP430 code.

NOTE: Sample code is also available on the DRV2700 product web page.

5.2 PWM (AC Coupled) Input Using AIN

The PWM input mode can be used with an external processor or PWM source. The PWM signal is a

carrier wave (duty-cycle modulated) at a frequency much higher than the analog signal it represents. The

PWM input mode can be used with an external processor or PWM source.

To use an external PWM source to drive the DRV2700, follow these instructions to modify the board:

1. Disconnect the MSP430 output pins from the DRV2700 input pins by removing jumpers JP5 and JP6

2. Depending on the input source, follow the instructions in the Filtering and Adapting PWM Waveforms

section to adjust the input filter.

3. Connect DRV2700 control signals:

a. Use the onboard MSP430 and GUI to control the EN, GAIN0, and GAIN1 pins.

b. Use an external controller or jumpers to control the EN, GAIN0, and GAIN1 pins.

4. Connect the positive terminal of the input signal source to AIN+ and the negative terminal to AIN–

5. Enable the power supply

PWM, Analog, and Single-Ended Inputs

www.ti.com

16 SLOU403C–March 2015–Revised June 2018

Submit Documentation Feedback

DRV2700EVM High Voltage Piezo Driver Evaluation Kit

5.3 External Analog (AC Coupled) Input

The following instructions are provided to use an external analog source (sine wave) to drive the

DRV2700:

1. Disconnect the MSP430 output pins from the DRV2700 input pins by removing jumpers JP6 and JP5

2. Modify the input filter according to the Filtering and Adapting PWM Waveforms section. The default

PWM filter is no longer necessary.

3. Connect the DRV2700 control signals:

a. Use the onboard MSP430 and GUI to control the EN, GAIN0, and GAIN1 pins

b. Use an external controller or jumpers to control the EN, GAIN0, and GAIN1 pins

4. Connect the positive terminal of the input signal source to AIN+ and the negative terminal to AIN–

5. Enable the power supply

5.4 Single-Ended (DC Coupled) Input

The DRV2700EVM can be operated with a DC input. There are two configurations available in this EVM

that show:

• Set reference

• Floating reference

In some applications, it is critical that the output does not go above or below a certain threshold. To help

mitigate this, landing pads for a zener diode on the DC input have been provided. Installing a properly-

selected zener can help assure the input does not go above the set voltage and therefore not allow the

output to swing above or below the undesired voltage.

5.4.1 Set Reference

The set reference configuration is used when the output needs to be controlled linearly. Just like a normal

amplifier, the output will be amplified based on the difference of the inputs. The DRV2700EVM has the

inputs connected to TP7 (IN+) and TP8 (IN–).

To use the DC input with a set reference to drive the DRV2700, follow these instructions:

1. Disconnect the MSP430 output pins from the DRV2700 input pins by removing jumpers JP6 and JP5

2. Connect JP_DC

3. Connect DRV2700 control signals:

a. Use the onboard MSP430 and GUI to control the EN, GAIN0, and GAIN1 pins

b. Use an external controller or jumpers to control the EN, GAIN0, and GAIN1 pins

4. DC reference input:

Connect the DC reference to TP8 (IN–)

5. Amplifying signal:

a. For 0–10 V range, connect jumper JP_DC and apply 0–10 V on DC_IN

b. For 0–5 V range, disconnect jumper JP_DC and apply 0–5 V on TP7 (IN+)

6. Enable the power supply

Figure 10 is with the EVM powered through USB (5 V).

www.ti.com

PWM, Analog, and Single-Ended Inputs

SLOU403C–March 2015–Revised June 2018

DRV2700EVM High Voltage Piezo Driver Evaluation Kit

Figure 10. Set Reference to External 2.5 V

See Figure 13 for a diagram of the input configuration.

5.4.2 Floating Reference

If the application is to create a high voltage square wave where the output goes from ±VBST, this floating

reference configuration is beneficial. Unlike most amplifiers where both input terminals need to be biased

to control the output, the DRV2700 has an internal compensated common mode to try and keep the inputs

near VDD / 2. This allows the application to eliminate the need of a reference voltage, by instead applying a

capacitor to ground on one of the input terminals. Because there is compensation between the two inputs,

the common mode will have some drift based on the other input signal. If the DRV2700 is going to be

operated in the linear region, the set reference configuration should be used.

Use the DC input with a floating reference to drive the DRV2700 with the following instructions:

1. Disconnect the MSP430 output pins from the DRV2700 input pins by removing jumpers JP6 and JP5

2. Connect DRV2700 control signals:

a. Use the onboard MSP430 and GUI to control the EN, GAIN0, and GAIN1 pins

b. Use an external controller or jumpers to control the EN, GAIN0, and GAIN1 pins

3. Amplifying signal:

a. For 0–10 V range, connect jumper JP_DC and apply 0–10 V on DC_IN

b. For 0–5 V range, disconnect jumper JP_DC and apply 0–5 V on TP7 (IN+)

4. Enable the power supply

Figure 11 and Figure 12 show this mode at 3 Hz and 1 KHz. Notice that the floating reference (IN-) will

vary based on the IN+ signal. This drift can be minimized by increasing the frequency. This configuration

should only be used as long as the application can handle this drift. Each application should be properly

evaluated to verify if this configuration will be acceptable per its system requirements. Figure 11 and

Figure 12 are with the EVM powered through USB (5 V).

See Figure 13 for a diagram of the input configuration.

IN+

INí

R16

10.0 NŸ

R16

10.0 NŸ

Filter

Network

Filter

Network

PWM+

PWMí

DC_IN

TP7

TP8

JP13

Signal

Generator

Reference

Voltage

Not Used in Floating

Reference Config

PWM, Analog, and Single-Ended Inputs

www.ti.com

18 SLOU403C–March 2015–Revised June 2018

Submit Documentation Feedback

DRV2700EVM High Voltage Piezo Driver Evaluation Kit

Figure 11. Floating Reference at 3 Hz and No Load Figure 12. Floating Reference at 1 Hz and No Load

Figure 13. DC Coupled Input Diagram

DRV2700

Piezo

Element

BST

OUT>

OUT+

GND

DRV2700

BST

OUT>

OUT+

GND

100 Vp

Piezo

Element

100 Vp

Piezo

Element

Piezo

Element

100 Vp

DRV2700 Piezo

Element

BST

OUT-

OUT+

GND

200 Vpp

www.ti.com

Output

SLOU403C–March 2015–Revised June 2018

DRV2700EVM High Voltage Piezo Driver Evaluation Kit

6 Output

The DRV2700 has 3 main outputs and GND on the 4-terminal output:

1. The output of the boost converter (BST)

2. The positive output of the amplifier (OUT+)

3. The negative output of the amplifier (VOUT–)

These outputs can be configured in a variety of ways and are described in more detail in this section.

6.1 Two Terminal Differential Output Configuration (OUT+ – OUT–)

The typical output configuration is a 2 terminal differential output with one terminal connected to OUT+

and the other connected to OUT–. This configuration can achieve 200 Vpp.

Figure 14. Two Terminal Differential Output

6.2 Two Terminal Single Ended Output Configuration (OUT± to BST/GND)

This output configuration allows for 2 outputs that are 180 degrees out of phase. This is configured with

OUT+ and/or OUT– referenced to GND with a voltage that can swing up to 100 V. Additionally, they can

be referenced to BST.

Figure 15. Two Terminal Single Ended Output

Piezo

Element

DRV2700 Piezo

Element

BST

OUT>

OUT+

GND

100 Vp

Output

www.ti.com

20 SLOU403C–March 2015–Revised June 2018

Submit Documentation Feedback

DRV2700EVM High Voltage Piezo Driver Evaluation Kit

6.3 Three Terminal Single Ended Output Configuration (BST to OUT± to GND)

The output configuration is very similar to the two terminal, however, only one output pin is used. This

ensures that the two voltage potentials (BST to OUTx and OUTx to GND) always add up to BST.

Figure 16. Three Terminal Single Ended Output

7 Load Selection

The DRV2700 is intended to drive Piezo (capacitive) loads, however, an improper load driven at certain

levels can cause the device to heat up and hit thermal shutdown. Therefore, there are several key

specifications to consider when choosing a Piezo load; such as dimensions, blocking force, and

displacement. However, the key electrical specifications from the driver perspective are voltage rating and

capacitance. At the maximum frequency of 500 Hz, the DRV2700 is optimized to drive up to 50 nF at 200

VPP, which is the highest voltage swing capability. The DRV2700 will drive larger capacitances if the

programmed boost voltage is lowered or the user limits the input frequency range to lower frequencies (for

example, 300 Hz). For more information, see the Piezo Load Selection section of the DRV2700 data sheet

(SLOS861).

See Figure 13 for a diagram of the input configuration.

www.ti.com

Filtering and Adapting PWM Waveforms

SLOU403C–March 2015–Revised June 2018

DRV2700EVM High Voltage Piezo Driver Evaluation Kit

8 Filtering and Adapting PWM Waveforms

The DRV2700EVM has the capability to support many different input filter configurations. Depending on

the input mode, input frequency, and input voltage, the filter can be adapted to attenuate any undesired

out-of-band content. This section describes the input filter requirements and the various respective

configurations.

8.1 PWM Input

When using a high-frequency PWM input, a low-pass filter is required. The primary parameters for

determining the input filter are the PWM input frequency and sample rate. Because of the power ratings of

the DRV2700, the input filter has been designed to attenuate frequencies above 500 Hz. For samples

rates above 20 kHz, a simple first-order RC filter is recommended; however, for sample rates much lower

(such as 8 kHz), a first-order filter may not sufficiently attenuate the high-frequency content. Thus, for

lower sampling rates, a second order RC filter may be required. The following sections describe example

filter configurations for both first- and second-order filters. The DRV2700EVM default configuration uses a

second-order differential filter, but it can be replaced by a first-order, single-ended, or differential filter.

Figure 17. DRV2700EVM First- and Second-Order Filters

R17

7.5k

R13

4.99k C15

100n

C16

100n

PWM+ IN+

R18

7.5k

R14

4.99k C18

100n

C19

100n

PWMíINí

Filtering and Adapting PWM Waveforms

www.ti.com

22 SLOU403C–March 2015–Revised June 2018

Submit Documentation Feedback

DRV2700EVM High Voltage Piezo Driver Evaluation Kit

8.2 Filter Selection Criteria

Apply these criteria to select an input filter:

1. First-order RC filters, both single-ended and differential, are recommended for 20 kHz and higher data

sample rates. The first-order filters have adequate settling time and the fewest components.

2. Second-order filters are recommended for noiseless operation when using a lower data sample rate

where a sharper cutoff is necessary

3. The attenuation at the PWM carrier frequency should be at least –40 dB

8.2.1 First-Order Filter

For sample rates 20 kHz and greater, a first-order filter is recommended. The first-order filter is used in

both single-ended or differential configurations. Figure 18 shows a differential, first-order filter. The PWM

input filter is optimized for a 3.3-V differential PWM input signal (–11-dB attenuation); remove R17 and

R18 when applying a 1.8-V input signal.

Figure 18. Differential, First-Order Filter

The first-order filter in Figure 18 contains one pole with a slope of –20 dB. Figure 19 shows the frequency

response of the first-order filter.

Figure 19. Frequency Response of the First-Order Filter

R17

2.7k

R13

3.3k C15

47n

C16

100n

PWM+ IN+

R18

2.7k

R14

3.3k C18

47n

C19

100n

PWMíINí

3.3k C15

47n

3.3k C18

47n

www.ti.com

Filtering and Adapting PWM Waveforms

SLOU403C–March 2015–Revised June 2018

DRV2700EVM High Voltage Piezo Driver Evaluation Kit

8.2.2 Second-Order Filter, Differential

For data sample rates less than 20 kHz, a second-order filter is recommended. A differential input signal is

recommended for use with a second-order filter because of the longer settling time. Figure 20 shows the

differential, second-order filter that is the default filter configuration for the EVM. The PWM input filter is

optimized for a 3.3-V differential PWM input signal (–1-dB attenuation); remove R17 and R18 when

applying a 1.8-V input signal.

Figure 20. Differential, Second-Order Filter

The second-order filter in Figure 20 contains two poles resulting in a slope of –40 dB. Figure 21 shows the

frequency response of the second-order filter.

Figure 21. Frequency Response of the Second-Order Filter

Filtering and Adapting PWM Waveforms

www.ti.com

24 SLOU403C–March 2015–Revised June 2018

Submit Documentation Feedback

DRV2700EVM High Voltage Piezo Driver Evaluation Kit

8.2.3 Remove Filter for Analog Input

If the input signal is an analog waveform, as opposed to a PWM, then an input filter may not be

necessary. Before removing the filter, ensure that a simple RC filter is not needed to remove any artifacts

from the digital-to-analog converter (DAC) output or other input source. Follow these instructions to

remove the input filter completely.

1. Replace resistors R6, R7, R13, and R14 with 0-Ωresistors

2. Remove resistors R17 and R18

3. Remove capacitors C8, C9, C13, and C14. Do not remove ac coupling capacitors C4 and C5.

See Figure 13 for a diagram of the input configuration.

3NC 4

OUT 5

GND

TLV70033DCKR

1000pF

0.047µF

C14

0.047µF

C17

0.047µF

C15

0.047µF

C18

PWM-

GAIN1

GAIN0

0.1µF

C13

BST

0.1µF

C16

0.1µF

C19

3.3k

R13

3.3k

R14

2.7k

R17

2.7k

R18

SW2

0.1µF

10k

R20

JP3

P6.0/CB0/A0 1

P6.1/CB1/A1 2

P6.2/CB2/A2 3

P6.3/CB3/A3 4

P5.0/A8/VEREF+ 5

P5.1/A9/VEREF- 6

AVCC1

P5.4/XIN 8

P5.5/XOUT 9

AVSS1 10

DVCC1

11 DVSS1 12

VCORE

P1.0/TA0CLK/ACLK

P1.1/TA0.0

P1.2/TA0.1

P1.3/TA0.2

P1.4/TA0.3

P1.5/TA0.4

P1.6/TA1CLK/CBOUT

P1.7/TA1.0

P2.0/TA1.1

PJ.0/TDO 23

PJ.1/TDI/TCLK 24

PJ.2/TMS 25

PJ.3/TCK 26

DVSS2 27

DVCC2

P4.0/PM_UCB1STE/PM_UCA1CLK

P4.1/PM_UCB1SIMO/PM_UCB1SDA

P4.2/PM_UCB1SOMI/PM_UCB1SCL

P4.3/PM_UCB1CLK/PM_UCA1STE

P4.4/PM_UCA1TXD/PM_UCA1SIMO

P4.5/PM_UCA1RXD/PM_UCA1SOMI

P4.6/PM_NONE

P4.7/PM_NONE

VSSU 37

PU.0/DP 38

PUR 39

PU.1/DM 40

VBUS

VUSB

V18

AVSS2 44

P5.2/XT2IN 45

P5.3/XT2OUT 46

TEST/SBWTCK 47

RST/NMI/SBWTDIO 48

PAD

MSP430F5510IRGZ

SCL

SDA

VBUS 1

D- 2

D+ 3

ID 4

GND 5

10µF

100µF

10µF

VBUS

0.1µF

C11

VBUS

D+

D-

0.47µF

9.76k

R10

49.9k

23.2k

80.6k

806k

JP2JP4

TRIG

PWM+

Green

511

R30

VIN

IN-

3p3

GND

GND GND

0.1µF

C12

GND

BST

JP12

PVDD

0.1µF

GND

3.3k

R22

3.3k

R23

Green

511

R25

Green

511

R26

Green

511

R27

EN GAIN1 GAIN0

3.3k

R24

GNDGNDGND

JP9

JP8

JP7

JP10

VIN

JP11

VIN

VBUS

GND

TP6

0.1uF

IO1

IO2

GND

3IO3 4

IO4 5

VCC 6

TPD4E004DRY

VBUS

GND

VBUS

VDRV

VREST

VREST VREST VREST

TP5

IN+

10.0k

R16

10.0k

R19

GND

DC_IN

JP5

SBWTDIO

SBWTCK

TP4

TP7

TP8

JP13

IN+

GND

100

R15

1.0Meg

R12

VBUS

GND

PUR

SW1

D+

D-

1.40k

R11

D+

PUR

0.22µF

C10

3 4

12MHz

ABM8G-12.000MHZ-B4Y-T

JP6

10k

R28

10k

R29

3p3

SCL

SDA

TEST2

TEST1

TEST3

TP1

DNP

TP2

DNP

TP3

DNP

10pF

C23

10pF

C22

5.6V

D1 5.6V

DNP

GND

VPUMP

VDD 2

FB 3

GND 4

GND 5

GND 6

SW 7

SW 8

BST

PVDD

OUT+ 13

OUT- 14

REXT 15

IN-

16 IN+

GAIN0

18 GAIN1

19 EN

PAD 21

DRV2700RGP

0.1µF

C21

OUT+

OUT-

GND

BST

6.04k

R21

4.7µH2.7A

L1 VDRV

GND

VDRV

GND

0.1µF

C20

IN+

IN-

PWM+_MSP PWM-_MSP

EN_MSP

GAIN1_MSP

GAIN0_MSP

EN_MSP GAIN1_MSP GAIN0_MSP

PWM+_MSP

PWM-_MSP

Power Inputs

Power Routing

DRV2700 Input Routing

DRV2700

MSP430

Boost Voltage Selection

Gain & EN Settings

External I2C

www.ti.com

Reference

SLOU403C–March 2015–Revised June 2018

Submit Documentation Feedback

DRV2700EVM High Voltage Piezo Driver Evaluation Kit

9 Reference

This section includes the DRV2700EVM schematic, PCB Layout, and Bill of Materials.

9.1 Schematic

Figure 22 illustrates the DRV2700EVM schematic.

Figure 22. DRV2700EVM Schematic

Reference

www.ti.com

26 SLOU403C–March 2015–Revised June 2018

Submit Documentation Feedback

DRV2700EVM High Voltage Piezo Driver Evaluation Kit

9.2 PCB Layout

Figure 23 through Figure 27 show the DRV2700EVM PCB layouts.

Figure 23. All Layers

Figure 24. Top Layer

www.ti.com

Reference

SLOU403C–March 2015–Revised June 2018

DRV2700EVM High Voltage Piezo Driver Evaluation Kit

Figure 25. Mid Layer 1

Figure 26. Mid Layer 2

Reference

www.ti.com

28 SLOU403C–March 2015–Revised June 2018

Submit Documentation Feedback

DRV2700EVM High Voltage Piezo Driver Evaluation Kit

Figure 27. Bottom Layer

9.3 Bill of Materials

Table 6 lists the DRV2700EVM bill of materials.

Table 6. Bill of Materials

Designator Qty. Value Description Package Reference Part Number Manufacturer

PCB 1 Printed Circuit Board AIP037 Any

C1, C4 2 10 µF CAP, CERM, 10uF, 16V, ±20%, X5R, 0805 805 0805YD106MAT2A AVX

C2 1 1000 pF CAP, CERM, 1000pF, 6.3V, ±10%, X5R, 0402 402 GRM155R60J102KA01D Murata

C3 1 100 µF CAP, CERM, 100uF, 6.3V, ±20%, X5R, 1206 1206 GRM31CR60J107ME39L Murata

C5 1 0.1 µF CAP, CERM, 0.1uF, 250V, ±10%, X7R, 1206 1206 C3216X7R2E104K TDK

C6 1 0.1 µF CAP CER 0.1UF 16V 5% X7R 0402 402 GRM155R71C104JA88D Murata Electronics

North America

C7, C11, C12 3 0.1 µF CAP, CERM, 0.1uF, 6.3V, ±10%, X5R, 0402 402 C1005X5R0J104K TDK

C8, C10 2 0.22 µF CAP, CERM, 0.22uF, 6.3V, ±10%, X6S, 0402 402 GRM155C80J224KE01D Murata

C9 1 0.47 µF CAP, CERM, 0.47uF, 10V, ±10%, X7R, 0603 603 C0603C474K8RACTU Kemet

C13, C16, C19, C20 4 0.1 µF CAP, CERM, 0.1uF, 16V, ±10%, X7R, 0402 402 GRM155R71C104KA88D Murata

C14, C15, C17, C18 4 0.047 µF CAP, CERM, 0.047uF, 16V, ±10%, X7R, 0402 402 GRM155R71C473KA01D Murata

C21 1 0.1 µF CAP, CERM, 0.1uF, 25V, ±10%, X5R, 0603 603 06033D104KAT2A AVX

C22, C23 2 10 pF CAP, CERM, 10pF, 50V, ±5%, C0G/NP0, 0402 402 GRM1555C1H100JA01D Murata

D1 1 5.6 V Diode, Zener, 5.6V, 500 mW, SOD-123 SOD-123 MMSZ5232B-7-F Diodes Inc.

D3, D4, D5, D6 4 Green LED, Green, SMD 1.6x0.8x0.8mm LTST-C190KGKT Lite-On

H1, H2, H3, H4 4 Bumpon, Hemisphere, 0.375 × 0.235, Black Black Bumpon SJ61A2 3M

J1 1 Connector, USB Mini B Connector, Mini B 897-43-005-00-100001 Mill-Max

J2, J5 2 Header, 2 Pos, 6A, 63V, TH 6.2x8.5x5.54 mm 1725656 Phoenix Contact

J3, JP7–JP10, JP11 6 Header, 100mil, 3x1, Tin, TH Header, 3x1,100mil,TH 5-146278-3 TE Connectivity

J4 1 Receptacle, 50mil, 6x1, R/A, TH 6x1 Receptacle LPPB061NGCN-RC Sullins Connector

Solutions

J6 1 Terminal Block, 4x1, 5.08 mm, TH 4x1 Terminal Block 39544-3004 Molex

JP2–JP6, JP12, JP13 7 Header, 100mil, 2x1, Tin, TH Header,2 Pin,100mil,Tin PEC02SAAN Sullins Connector

Solutions

www.ti.com

Reference

SLOU403C–March 2015–Revised June 2018

DRV2700EVM High Voltage Piezo Driver Evaluation Kit

Table 6. Bill of Materials (continued)

Designator Qty. Value Description Package Reference Part Number Manufacturer

L1 1 4.7 µH Inductor, Shielded, Composite, 4.7 µH,

2.7A, 0.05 Ω, SMD 4x2x4mm XFL4020-472MEB Coilcraft

R1, R3 2 49.9 k RES, 49.9 kΩ, 1%, 0.063W, 0402 402 CRCW040249K9FKED Vishay-Dale

R2 1 23.2 k RES, 23.2 kΩ, 1%, 0.063W, 0402 402 CRCW040223K2FKED Vishay-Dale

R4 1 80.6 k RES, 80.6 kΩ, 1%, 0.063W, 0402 402 CRCW040280K6FKED Vishay-Dale

R5 1 806 k RES, 806 kΩ, 1%, 0.063W, 0402 402 CRCW0402806KFKED Vishay-Dale

R6, R7, R13, R14,

R22–R24 7 3.3 k RES, 3.3 kΩ, 5%, 0.063W, 0402 402 CRCW04023K30JNED Vishay-Dale

R8, R9 2 33 RES, 33 Ω, 5%, 0.063W, 0402 402 CRCW040233R0JNED Vishay-Dale

R10 1 9.76 k RES, 9.76 kΩ, 1%, 0.063W, 0402 402 CRCW04029K76FKED Vishay-Dale

R11 1 1.40 k RES, 1.40 kΩ, 1%, 0.063W, 0402 402 CRCW04021K40FKED Vishay-Dale

R12 1 1.0 Meg RES, 1.0 MΩ, 5%, 0.063W, 0402 402 CRCW04021M00JNED Vishay-Dale

R15 1 100 RES, 100 Ω, 1%, 0.063W, 0402 402 CRCW0402100RFKED Vishay-Dale

R16, R19 2 10.0 k RES, 10.0 kΩ, 1%, 0.063W, 0402 402 CRCW040210K0FKED Vishay-Dale

R17, R18 2 2.7 k RES, 2.7 kΩ, 5%, 0.063W, 0402 402 CRCW04022K70JNED Vishay-Dale

R20, R28, R29 3 10 k RES, 10 kΩ, 5%, 0.063W, 0402 402 CRCW040210K0JNED Vishay-Dale

R21 1 6.04 k RES, 6.04 kΩ, 1%, 0.063W, 0402 402 CRCW04026K04FKED Vishay-Dale

R25, R26, R27, R30 4 511 RES, 511 Ω, 1%, 0.063W, 0402 402 CRCW0402511RFKED Vishay-Dale

SH-JP1–SH-JP11 11 1x2 Shunt, 2mm, Gold plated, Black 2mm Shunt,Closed Top 2SN-BK-G Samtec

SW1, SW2 2 Switch, Tactile, SPST-NO, 0.05A, 12V, SMT Switch, 4.4x2x2.9 mm TL1015AF160QG E-Switch

TP4 1 Orange Test Point, Miniature, Orange, TH Orange Miniature

Testpoint 5003 Keystone

TP5, TP6 2 Black Test Point, Multipurpose, Black, TH Black Multipurpose

Testpoint 5011 Keystone

TP7, TP8 2 White Test Point, Miniature, White, TH White Miniature Testpoint 5002 Keystone

U1 1 Piezo Driver with Integrated Boost Converter, RGP0020D RGP0020D DRV2700RGP Texas Instruments

U2 1 4-ChanneL ESD-protection array for high-speed data

interfaces, DRY006A DRY0006A TPD4E004DRY Texas Instruments

U3 1 Single Output LDO, 200 mA, Fixed 3.3 V Output, 2 to 5.5

V Input, with Low IQ, 5-pin SC70 (DCK), –40°C to 125°C,

Green (RoHS and no Sb/Br) DCK0005A TLV70033DCKR Texas Instruments

U4 1 Mixed Signal MicroController, RGZ0048A RGZ0048A MSP430F5510IRGZ Texas Instruments

Y1 1 CRYSTAL 12.000 MHz 10PF SMD 3.2x0.55x2.5mm ABM8G-12.000MHZ-

B4Y-T Abracon Corporation

10 Trademarks

Code Composer Studio, LaunchPad are trademarks of Texas Instruments.

All other trademarks are the property of their respective owners.

Revision History

www.ti.com

30 SLOU403C–March 2015–Revised June 2018

Submit Documentation Feedback

Revision History

NOTE: Page numbers for previous revisions may differ from page numbers in the current version.

Changes from Original (March 2015) to A Revision ....................................................................................................... Page

• Changed value on R5in BST Network JP2, JP3, and JP4 image................................................................. 13

Revision History

Changes from A Revision (April 2015) to B Revision .................................................................................................... Page

• Changed content in JP11 row of the Default Jumper Settings table. .............................................................. 7

• Changed connector lines in Power Path Diagram. ................................................................................... 8

Revision History

Changes from B Revision (April 2015) to C Revision .................................................................................................... Page

• Added: "MSP-JTAG2SBW JTAG to Spy-Bi-Wire adapter" to the advanced configuration list.................................. 1

• Deleted sentence: "The DRV2700EVM kit includes a JTAG-to-SpyBiWire adapter for connecting the JTAG interface to the

DRV2700EVM SpyBiWire connector" from Section 5.1 ............................................................................ 15

STANDARD TERMS FOR EVALUATION MODULES

1. Delivery: TI delivers TI evaluation boards, kits, or modules, including any accompanying demonstration software, components, and/or

documentation which may be provided together or separately (collectively, an “EVM” or “EVMs”) to the User (“User”) in accordance

with the terms set forth herein. User's acceptance of the EVM is expressly subject to the following terms.

1.1 EVMs are intended solely for product or software developers for use in a research and development setting to facilitate feasibility

evaluation, experimentation, or scientific analysis of TI semiconductors products. EVMs have no direct function and are not

finished products. EVMs shall not be directly or indirectly assembled as a part or subassembly in any finished product. For

clarification, any software or software tools provided with the EVM (“Software”) shall not be subject to the terms and conditions

set forth herein but rather shall be subject to the applicable terms that accompany such Software

1.2 EVMs are not intended for consumer or household use. EVMs may not be sold, sublicensed, leased, rented, loaned, assigned,

or otherwise distributed for commercial purposes by Users, in whole or in part, or used in any finished product or production

system.

2Limited Warranty and Related Remedies/Disclaimers:

2.1 These terms do not apply to Software. The warranty, if any, for Software is covered in the applicable Software License

Agreement.

2.2 TI warrants that the TI EVM will conform to TI's published specifications for ninety (90) days after the date TI delivers such EVM

to User. Notwithstanding the foregoing, TI shall not be liable for a nonconforming EVM if (a) the nonconformity was caused by

neglect, misuse or mistreatment by an entity other than TI, including improper installation or testing, or for any EVMs that have

been altered or modified in any way by an entity other than TI, (b) the nonconformity resulted from User's design, specifications

or instructions for such EVMs or improper system design, or (c) User has not paid on time. Testing and other quality control

techniques are used to the extent TI deems necessary. TI does not test all parameters of each EVM.

User's claims against TI under this Section 2 are void if User fails to notify TI of any apparent defects in the EVMs within ten (10)

business days after delivery, or of any hidden defects with ten (10) business days after the defect has been detected.

2.3 TI's sole liability shall be at its option to repair or replace EVMs that fail to conform to the warranty set forth above, or credit

User's account for such EVM. TI's liability under this warranty shall be limited to EVMs that are returned during the warranty

period to the address designated by TI and that are determined by TI not to conform to such warranty. If TI elects to repair or

replace such EVM, TI shall have a reasonable time to repair such EVM or provide replacements. Repaired EVMs shall be

warranted for the remainder of the original warranty period. Replaced EVMs shall be warranted for a new full ninety (90) day

warranty period.

3Regulatory Notices:

3.1 United States

3.1.1 Notice applicable to EVMs not FCC-Approved:

FCC NOTICE: This kit is designed to allow product developers to evaluate electronic components, circuitry, or software

associated with the kit to determine whether to incorporate such items in a finished product and software developers to write

software applications for use with the end product. This kit is not a finished product and when assembled may not be resold or

otherwise marketed unless all required FCC equipment authorizations are first obtained. Operation is subject to the condition

that this product not cause harmful interference to licensed radio stations and that this product accept harmful interference.

Unless the assembled kit is designed to operate under part 15, part 18 or part 95 of this chapter, the operator of the kit must

operate under the authority of an FCC license holder or must secure an experimental authorization under part 5 of this chapter.

3.1.2 For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant:

CAUTION

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) this device must accept any interference received, including interference that may cause

undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to

operate the equipment.

FCC Interference Statement for Class A EVM devices

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of

the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to

correct the interference at his own expense.

FCC Interference Statement for Class B EVM devices

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of

the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more

of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

3.2 Canada

3.2.1 For EVMs issued with an Industry Canada Certificate of Conformance to RSS-210 or RSS-247

Concerning EVMs Including Radio Transmitters:

This device complies with Industry Canada license-exempt RSSs. Operation is subject to the following two conditions:

(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may

cause undesired operation of the device.

Concernant les EVMs avec appareils radio:

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation

est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit

accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

Concerning EVMs Including Detachable Antennas:

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser)

gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type

and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for

successful communication. This radio transmitter has been approved by Industry Canada to operate with the antenna types

listed in the user guide with the maximum permissible gain and required antenna impedance for each antenna type indicated.

Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited

for use with this device.

Concernant les EVMs avec antennes détachables

Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et

d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage

radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope

rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. Le

présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le

manuel d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne

non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de

l'émetteur

3.3 Japan

3.3.1 Notice for EVMs delivered in Japan: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page 日本国内に

輸入される評価用キット、ボードについては、次のところをご覧ください。

http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page

3.3.2 Notice for Users of EVMs Considered “Radio Frequency Products” in Japan: EVMs entering Japan may not be certified

by TI as conforming to Technical Regulations of Radio Law of Japan.

If User uses EVMs in Japan, not certified to Technical Regulations of Radio Law of Japan, User is required to follow the

instructions set forth by Radio Law of Japan, which includes, but is not limited to, the instructions below with respect to EVMs

(which for the avoidance of doubt are stated strictly for convenience and should be verified by User):

1. Use EVMs in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal

Affairs and Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for

Enforcement of Radio Law of Japan,

2. Use EVMs only after User obtains the license of Test Radio Station as provided in Radio Law of Japan with respect to

EVMs, or

3. Use of EVMs only after User obtains the Technical Regulations Conformity Certification as provided in Radio Law of Japan

with respect to EVMs. Also, do not transfer EVMs, unless User gives the same notice above to the transferee. Please note

that if User does not follow the instructions above, User will be subject to penalties of Radio Law of Japan.

【無線電波を送信する製品の開発キットをお使いになる際の注意事項】開発キットの中には技術基準適合証明を受けて

いないものがあります。技術適合証明を受けていないもののご使用に際しては、電波法遵守のため、以下のいずれかの

措置を取っていただく必要がありますのでご注意ください。

1. 電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用

いただく。

2. 実験局の免許を取得後ご使用いただく。

3. 技術基準適合証明を取得後ご使用いただく。

なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。

上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。日本テキサス・イ

ンスツルメンツ株式会社

東京都新宿区西新宿６丁目２４番１号

西新宿三井ビル

3.3.3 Notice for EVMs for Power Line Communication: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page

電力線搬送波通信についての開発キットをお使いになる際の注意事項については、次のところをご覧ください。http:/

/www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page

3.4 European Union

3.4.1 For EVMs subject to EU Directive 2014/30/EU (Electromagnetic Compatibility Directive):

This is a class A product intended for use in environments other than domestic environments that are connected to a

low-voltage power-supply network that supplies buildings used for domestic purposes. In a domestic environment this

product may cause radio interference in which case the user may be required to take adequate measures.

4EVM Use Restrictions and Warnings:

4.1 EVMS ARE NOT FOR USE IN FUNCTIONAL SAFETY AND/OR SAFETY CRITICAL EVALUATIONS, INCLUDING BUT NOT

LIMITED TO EVALUATIONS OF LIFE SUPPORT APPLICATIONS.

4.2 User must read and apply the user guide and other available documentation provided by TI regarding the EVM prior to handling

or using the EVM, including without limitation any warning or restriction notices. The notices contain important safety information

related to, for example, temperatures and voltages.

4.3 Safety-Related Warnings and Restrictions:

4.3.1 User shall operate the EVM within TI’s recommended specifications and environmental considerations stated in the user

guide, other available documentation provided by TI, and any other applicable requirements and employ reasonable and

customary safeguards. Exceeding the specified performance ratings and specifications (including but not limited to input

and output voltage, current, power, and environmental ranges) for the EVM may cause personal injury or death, or

property damage. If there are questions concerning performance ratings and specifications, User should contact a TI

field representative prior to connecting interface electronics including input power and intended loads. Any loads applied

outside of the specified output range may also result in unintended and/or inaccurate operation and/or possible

permanent damage to the EVM and/or interface electronics. Please consult the EVM user guide prior to connecting any

load to the EVM output. If there is uncertainty as to the load specification, please contact a TI field representative.

During normal operation, even with the inputs and outputs kept within the specified allowable ranges, some circuit

components may have elevated case temperatures. These components include but are not limited to linear regulators,

switching transistors, pass transistors, current sense resistors, and heat sinks, which can be identified using the

information in the associated documentation. When working with the EVM, please be aware that the EVM may become

very warm.

4.3.2 EVMs are intended solely for use by technically qualified, professional electronics experts who are familiar with the

dangers and application risks associated with handling electrical mechanical components, systems, and subsystems.

User assumes all responsibility and liability for proper and safe handling and use of the EVM by User or its employees,

affiliates, contractors or designees. User assumes all responsibility and liability to ensure that any interfaces (electronic

and/or mechanical) between the EVM and any human body are designed with suitable isolation and means to safely

limit accessible leakage currents to minimize the risk of electrical shock hazard. User assumes all responsibility and

liability for any improper or unsafe handling or use of the EVM by User or its employees, affiliates, contractors or

designees.

4.4 User assumes all responsibility and liability to determine whether the EVM is subject to any applicable international, federal,

state, or local laws and regulations related to User’s handling and use of the EVM and, if applicable, User assumes all

responsibility and liability for compliance in all respects with such laws and regulations. User assumes all responsibility and

liability for proper disposal and recycling of the EVM consistent with all applicable international, federal, state, and local

requirements.

5. Accuracy of Information: To the extent TI provides information on the availability and function of EVMs, TI attempts to be as accurate

as possible. However, TI does not warrant the accuracy of EVM descriptions, EVM availability or other information on its websites as

accurate, complete, reliable, current, or error-free.

6. Disclaimers:

6.1 EXCEPT AS SET FORTH ABOVE, EVMS AND ANY MATERIALS PROVIDED WITH THE EVM (INCLUDING, BUT NOT

LIMITED TO, REFERENCE DESIGNS AND THE DESIGN OF THE EVM ITSELF) ARE PROVIDED "AS IS" AND "WITH ALL

FAULTS." TI DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, REGARDING SUCH ITEMS, INCLUDING BUT

NOT LIMITED TO ANY EPIDEMIC FAILURE WARRANTY OR IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS

FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF ANY THIRD PARTY PATENTS, COPYRIGHTS, TRADE

SECRETS OR OTHER INTELLECTUAL PROPERTY RIGHTS.

6.2 EXCEPT FOR THE LIMITED RIGHT TO USE THE EVM SET FORTH HEREIN, NOTHING IN THESE TERMS SHALL BE

CONSTRUED AS GRANTING OR CONFERRING ANY RIGHTS BY LICENSE, PATENT, OR ANY OTHER INDUSTRIAL OR

INTELLECTUAL PROPERTY RIGHT OF TI, ITS SUPPLIERS/LICENSORS OR ANY OTHER THIRD PARTY, TO USE THE

EVM IN ANY FINISHED END-USER OR READY-TO-USE FINAL PRODUCT, OR FOR ANY INVENTION, DISCOVERY OR

IMPROVEMENT, REGARDLESS OF WHEN MADE, CONCEIVED OR ACQUIRED.

7. USER'S INDEMNITY OBLIGATIONS AND REPRESENTATIONS. USER WILL DEFEND, INDEMNIFY AND HOLD TI, ITS

LICENSORS AND THEIR REPRESENTATIVES HARMLESS FROM AND AGAINST ANY AND ALL CLAIMS, DAMAGES, LOSSES,

EXPENSES, COSTS AND LIABILITIES (COLLECTIVELY, "CLAIMS") ARISING OUT OF OR IN CONNECTION WITH ANY

HANDLING OR USE OF THE EVM THAT IS NOT IN ACCORDANCE WITH THESE TERMS. THIS OBLIGATION SHALL APPLY

WHETHER CLAIMS ARISE UNDER STATUTE, REGULATION, OR THE LAW OF TORT, CONTRACT OR ANY OTHER LEGAL

THEORY, AND EVEN IF THE EVM FAILS TO PERFORM AS DESCRIBED OR EXPECTED.

8. Limitations on Damages and Liability:

8.1 General Limitations. IN NO EVENT SHALL TI BE LIABLE FOR ANY SPECIAL, COLLATERAL, INDIRECT, PUNITIVE,

INCIDENTAL, CONSEQUENTIAL, OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF THESE

TERMS OR THE USE OF THE EVMS , REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES. EXCLUDED DAMAGES INCLUDE, BUT ARE NOT LIMITED TO, COST OF REMOVAL OR

REINSTALLATION, ANCILLARY COSTS TO THE PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES, RETESTING,

OUTSIDE COMPUTER TIME, LABOR COSTS, LOSS OF GOODWILL, LOSS OF PROFITS, LOSS OF SAVINGS, LOSS OF

USE, LOSS OF DATA, OR BUSINESS INTERRUPTION. NO CLAIM, SUIT OR ACTION SHALL BE BROUGHT AGAINST TI

MORE THAN TWELVE (12) MONTHS AFTER THE EVENT THAT GAVE RISE TO THE CAUSE OF ACTION HAS

OCCURRED.

8.2 Specific Limitations. IN NO EVENT SHALL TI'S AGGREGATE LIABILITY FROM ANY USE OF AN EVM PROVIDED

HEREUNDER, INCLUDING FROM ANY WARRANTY, INDEMITY OR OTHER OBLIGATION ARISING OUT OF OR IN

CONNECTION WITH THESE TERMS, , EXCEED THE TOTAL AMOUNT PAID TO TI BY USER FOR THE PARTICULAR

EVM(S) AT ISSUE DURING THE PRIOR TWELVE (12) MONTHS WITH RESPECT TO WHICH LOSSES OR DAMAGES ARE

CLAIMED. THE EXISTENCE OF MORE THAN ONE CLAIM SHALL NOT ENLARGE OR EXTEND THIS LIMIT.

9. Return Policy. Except as otherwise provided, TI does not offer any refunds, returns, or exchanges. Furthermore, no return of EVM(s)

will be accepted if the package has been opened and no return of the EVM(s) will be accepted if they are damaged or otherwise not in

a resalable condition. If User feels it has been incorrectly charged for the EVM(s) it ordered or that delivery violates the applicable

order, User should contact TI. All refunds will be made in full within thirty (30) working days from the return of the components(s),

excluding any postage or packaging costs.

10. Governing Law: These terms and conditions shall be governed by and interpreted in accordance with the laws of the State of Texas,

without reference to conflict-of-laws principles. User agrees that non-exclusive jurisdiction for any dispute arising out of or relating to

these terms and conditions lies within courts located in the State of Texas and consents to venue in Dallas County, Texas.

Notwithstanding the foregoing, any judgment may be enforced in any United States or foreign court, and TI may seek injunctive relief

in any United States or foreign court.

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265

IMPORTANT NOTICE FOR TI DESIGN INFORMATION AND RESOURCES

Texas Instruments Incorporated (‘TI”) technical, application or other design advice, services or information, including, but not limited to,

reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to assist designers who are

developing applications that incorporate TI products; by downloading, accessing or using any particular TI Resource in any way, you

(individually or, if you are acting on behalf of a company, your company) agree to use it solely for this purpose and subject to the terms of

this Notice.

TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI

products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,

enhancements, improvements and other changes to its TI Resources.

You understand and agree that you remain responsible for using your independent analysis, evaluation and judgment in designing your

applications and that you have full and exclusive responsibility to assure the safety of your applications and compliance of your applications

(and of all TI products used in or for your applications) with all applicable regulations, laws and other applicable requirements. You

represent that, with respect to your applications, you have all the necessary expertise to create and implement safeguards that (1)

anticipate dangerous consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that

might cause harm and take appropriate actions. You agree that prior to using or distributing any applications that include TI products, you

will thoroughly test such applications and the functionality of such TI products as used in such applications. TI has not conducted any

testing other than that specifically described in the published documentation for a particular TI Resource.

You are authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that include

the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO

ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY

RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or

other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information

regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or

endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the

third party, or a license from TI under the patents or other intellectual property of TI.

TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR

REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING TI RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO

ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF

MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL

PROPERTY RIGHTS.

TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY YOU AGAINST ANY CLAIM, INCLUDING BUT NOT

LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF PRODUCTS EVEN IF

DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL, DIRECT, SPECIAL,

COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN CONNECTION WITH OR

ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE

POSSIBILITY OF SUCH DAMAGES.

You agree to fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of your non-

compliance with the terms and provisions of this Notice.

This Notice applies to TI Resources. Additional terms apply to the use and purchase of certain types of materials, TI products and services.

These include; without limitation, TI’s standard terms for semiconductor products http://www.ti.com/sc/docs/stdterms.htm), evaluation

modules, and samples (http://www.ti.com/sc/docs/sampterms.htm).

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265

DRV2700EVM User's Guide (Rev. C) DRV2700 EVA Manual

Navigation menu

Versions of this User Manual:

Views

Navigation