DSR 2000 Service Manual Volume 1 DSR2000_VOL1 DSR2000 VOL1

User Manual: DSR2000_VOL1

Open the PDF directly: View PDF .
Page Count: 344

Download
Open PDF In Browser	View PDF

DIGITAL VIDEOCASSETTE RECORDER

DSR-2000
DSR-2000P
i.LINK/DV INPUT/OUTPUT BOARD

DSBK-190
REMOTE CONTROL PANEL

DSBK-200
SERVICE MANUAL
Volume 1 1st Edition (Revised 1)

! WARNING
This manual is intended for qualified service personnel only.
To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so. Refer all servicing to
qualified service personnel.

! WARNUNG
Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.
Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die
Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei
Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben
Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung
dazu besitzen.

! AVERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin
de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les
réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.
Pour toute réparation faire appel à une personne compétente uniquement.

DSR-2000/2000P

CAUTION

ADVARSEL

Danger of explosion if battery is incorrectly replaced.

Lithiumbatteri - Eksplosjonsfare.
Ved utskifting benyttes kun batteri som
anbefalt av apparatfabrikanten.
Brukt batteri returneres
apparatleverandøren.

Replace only with the same or equivalent type
recommended by the manufacturer.
Dispose of used batteries according to the
manufacturer’s instructions.

Vorsicht!

VARNING

Explosionsgefahr bei unsachgemäßem Austausch
der Batterie.

Explosionsfara vid felaktigt batteribyte.
Använd samma batterityp eller en likvärdig typ
som rekommenderas av apparattillverkaren.
Kassera använt batteri enligt gällande
föreskrifter.

Ersatz nur durch denselben oder einen vom
Hersteller empfohlenen ähnlichen Typ. Entsorgung
gebrauchter Batterien nach Angaben des
Herstellers.

ATTENTION

VAROITUS

Il y a danger d’explosion s’il y a remplacement
incorrect de la batterie.

Paristo voi räjähtää jos se on virheellisesti
asennettu.
Vaihda paristo ainoastaan laitevalmistajan
suosittelemaan tyyppiin.
Hävitä käytetty paristo valmistajan ohjeiden
mukaisesti.

Remplacer uniquement avec une batterie du même
type ou d’un type équivalent recommandé par le
constructeur.
Mettre au rebut les batteries usagées conformément
aux instructions du fabricant.

ADVARSEL!
Lithiumbatteri-Eksplosionsfare ved fejlagtig
håndtering.
Udskiftning må kun ske med batteri
af samme fabrikat og type.
Levér det brugte batteri tilbage til leverandøren.

DSR-2000/2000P

1 (P)

Für Kunden in Deutschland

Voor de klanten in Nederland

Entsorgungshinweis: Bitte werfen Sie nur entladene
Batterien in die Sammelboxen beim Handel oder den
Kommunen. Entladen sind Batterien in der Regel dann,
wenn das Gerät abschaltet und signalisiert “Batterie
leer” oder nach längerer Gebrauchsdauer der Batterien
“nicht mehr einwandfrei funktioniert”. Um
sicherzugehen, kleben Sie die Batteriepole z.B. mit
einem Klebestreifen ab oder geben Sie die Batterien
einzeln in einen Plastikbeutel.

Dit apparaat bevat een MnO2-Li batterij voor memory
back-up.

Raadpleeg uw leverancier over de verwijdering van de
batterij op het moment dat u het apparaat bij einde
levensduur afdankt.

Gooi de batterij niet weg. maar lever hem in als KCA.

Bij dit produkt zijn batterijen geleverd.
Wanneer deze leeg zijn, moet u ze niet
weggooien maar inleveren als KCA.

2 (P)

DSR-2000/2000P

Table of Contents
Manual Structure
Purpose of this manual .............................................................................................. 7
Related manuals ......................................................................................................... 7
Contents ..................................................................................................................... 8

1. Operating Instructions
1-1.
1-2.
1-3.

DSR-2000 .................................................................................................... 1-1
DSBK-190 ................................................................................................. 1-81
DSBK-200 ................................................................................................. 1-86

2. Installation
2-1.
2-2.
2-3.
2-4.
2-5.
2-6.
2-7.
2-8.

2-9.

Installation Procedure.................................................................................. 2-1
Operational Environment ............................................................................ 2-1
Operating Voltage ....................................................................................... 2-1
Installation Space ........................................................................................ 2-2
Supplied Accessories .................................................................................. 2-2
Optional Accessories ................................................................................... 2-2
Rack Mounting ............................................................................................ 2-3
Connectors................................................................................................... 2-5
2-8-1. Connectors/Cables...................................................................... 2-5
2-8-2. Input/Output Signals of the Connectors ..................................... 2-6
Installation Setup and Adjustment ............................................................ 2-10
2-9-1. Switch Settings on the Connector Panel .................................. 2-10
2-9-2. Front Panel Setting ................................................................... 2-11
2-9-3. On-board Switch Setting .......................................................... 2-12
2-9-4. System Adjustment After Installation ...................................... 2-14

3. Service Overview
3-1.

3-2.
3-3.
3-4.

DSR-2000/2000P

Location of Main Parts ................................................................................ 3-1
3-1-1. Location of Printed Circuit Boards ............................................ 3-1
3-1-2. Location of Main Mechanical Parts ........................................... 3-6
3-1-3. Location of Sensors .................................................................... 3-7
Functions of Record Proof Hole and Record Proof Plug of Cassette ......... 3-9
Removal/Installation of Cabinet ............................................................... 3-10
Removal/Reattachment of the Cassette Compartment .............................. 3-13

3-5.

3-6.
3-7.
3-8.
3-9.

Removal/Reattachment of the Boards ....................................................... 3-14
3-5-1. Removal/Reattachment of the Card Boards ............................. 3-14
3-5-2. Extension Board ....................................................................... 3-14
3-5-3. Removal/Reattachment of the Boards ...................................... 3-15
Notes on Repair Parts ................................................................................ 3-32
3-6-1. Flexible Card Wire Replacement ............................................. 3-32
Replacement of Lithium Battery ............................................................... 3-35
Fixtures and Tools list ............................................................................... 3-36
Upgrading the System/Servo CPU Program Version ............................... 3-38
3-9-1. Version Upgrade using the DJ-376 .......................................... 3-38
3-9-2. Version Upgrade from a PC through RS-422 .......................... 3-39

4. Error Messages
4-1.
4-2.

4-3.

Alarm Display ............................................................................................. 4-1
4-1-1. Alarm Display when the Main Power is Turned On .................. 4-1
Error Codes ................................................................................................. 4-3
4-2-1. Display of Previously Detected Error Codes ............................. 4-5
4-2-2. Main Codes and Sub Codes ....................................................... 4-6
4-2-3. Error Codes ................................................................................ 4-8
4-2-4. Possible Causes of Errors ......................................................... 4-14
Countermeasure in an Emergency ............................................................ 4-16
4-3-1. How to Take Out the Cassette Whose Tape is Slacked
(MANUAL EJECT) ................................................................. 4-16
4-3-2. Head Cleaning when Head Clogging Occurs ........................... 4-17
4-3-3. Operating the VTR without A Cassette Tape .......................... 4-17

5. Maintenance Menu
5-1.
5-2.

5-3.

Menu Structure ............................................................................................ 5-1
How to Operate Maintenance Menu ........................................................... 5-3
5-2-1. Location and Function of Switches ............................................ 5-3
5-2-2. How to Enter the Maintenance Menu ........................................ 5-3
5-2-3. How to Exit the Maintenance Menu .......................................... 5-3
Contents of Maintenance Menu .................................................................. 5-4
5-3-1. Menu Data Control ..................................................................... 5-4
5-3-2. Servo Check ............................................................................... 5-7
5-3-3. Servo Adjust ............................................................................. 5-21
5-3-4. Tape Path Adjust ...................................................................... 5-28
5-3-5. Electrical Adjust ....................................................................... 5-29
5-3-6. Service Support ........................................................................ 5-38
5-3-7. Others ....................................................................................... 5-40

DSR-2000/2000P

6. Periodic Inspection and Maintenance
6-1.
6-2.
6-3.

Periodic Inspection List............................................................................... 6-1
Hours Meter ................................................................................................ 6-2
Maintenance upon Completion of Repair ................................................... 6-4
6-3-1. Video Head Cleaning Procedure ................................................ 6-4
6-3-3. Cassette Compartment Entrance Cleaning ................................. 6-5
6-3-4. Cassette Compartment Shaft Cleaning....................................... 6-5
6-3-5. Cassette Guide Assembly Cleaning ........................................... 6-5

7. Replacement of Mechanical Parts
7-1.

7-2.
7-3.
7-4.
7-5.
7-6.
7-7.
7-8.
7-9.
7-10.
7-11.
7-12.
7-13.
7-14.
7-15.
7-16.
7-17.
7-18.
7-19.
7-20.
7-21.
7-22.
7-23.
7-24.

DSR-2000/2000P

General Information on Parts Replacement and Adjustment ...................... 7-1
7-1-1. Preparation Before Starting Parts Replacement ......................... 7-1
7-1-2. Drum Assembly ......................................................................... 7-1
7-1-3. Grease ......................................................................................... 7-1
7-1-4. Tightening Torque and Handling of Washers ............................ 7-2
Drum Replacement...................................................................................... 7-3
S/T Brake Assembly Replacement.............................................................. 7-8
Brake Solenoid Replacement .................................................................... 7-12
Pinch Roller Replacement ......................................................................... 7-17
Elevator Cam Replacement ....................................................................... 7-19
Pinch Solenoid Assembly Replacement.................................................... 7-21
Reel Motor (T) Assembly Replacement ................................................... 7-23
Reel Motor (S) Assembly Replacement .................................................... 7-27
M Stop Solenoid Assembly Replacement ................................................. 7-31
S Tension Regulator Assembly Replacement ........................................... 7-34
T Drawer Arm Assembly Replacement .................................................... 7-37
TG1 Arm Assembly Replacement ............................................................ 7-39
TG8 Arm Assembly Replacement ............................................................ 7-41
Rail Assembly Replacement ..................................................................... 7-43
Capstan Motor Replacement ..................................................................... 7-49
Loading Motor Replacement..................................................................... 7-51
Reel Shift Motor Assembly Replacement ................................................. 7-52
MIC Assembly Replacement .................................................................... 7-54
MIC Holder Assembly Replacement ........................................................ 7-58
HC Roller Assembly Replacement ........................................................... 7-60
Head Cleaner Solenoid Replacement ........................................................ 7-63
Cassette Compartment Motor Replacement.............................................. 7-65
Switching Regulator Replacement ............................................................ 7-67

8. Tape Path Alignment
8-1.
8-2.
8-3.
8-4.
8-5.
8-6.
8-7.
8-8.

General Information for Tape Path Adjustment .......................................... 8-1
Tape Path Adjustment ................................................................................. 8-6
RF Switching Position Adjustment ............................................................. 8-9
Tape Path Adjustment Confirmation ........................................................ 8-12
Search Forward (x5) Waveform Check .................................................... 8-13
Search Reverse (x5) Waveform Check .................................................... 8-14
RF Waveform Raiseup Check ................................................................... 8-15
Tape Curl Check at Tape Guide ................................................................ 8-16

9. Adjustment When Replacing Board
9-1.

Adjustment/Check Items When Replacing Board ...................................... 9-1

10. Electrical Alignment
10-1. Electrical Alignment Overview ................................................................. 10-1
10-1-1. List of Adjustment Parts ........................................................... 10-1
10-1-2. Measuring Equipment and Tools ............................................. 10-2
10-1-3. Reference Tape for Alignment ................................................. 10-2
10-2. Audio Adjustment ..................................................................................... 10-4
10-2-1. Audio OUTPUT Level Adjustment ......................................... 10-4
10-2-2. Audio EE Level Adjustment .................................................... 10-4
10-3. Video Adjustment ..................................................................................... 10-5
10-3-1. INT SC Frequency Adjustment ................................................ 10-6
10-3-2. HCK Frequency Adjustment .................................................... 10-6
10-3-3. COMPONENT Y OUT Level Adjustment .............................. 10-7
10-3-4. COMPONENT B-Y OUT Level Adjustment .......................... 10-7
10-3-5. COMPONENT R-Y OUT Level Adjustment .......................... 10-8
10-3-6. SETUP OFF Chroma Level Check (NTSC only) .................... 10-8
10-3-7. S VIDEO OUT Y Level Check ................................................ 10-9
10-3-8. VIDEO OUT 1 Video/Sync Level Adjustment ....................... 10-9
10-3-9. VIDEO OUT 2 Video Level Check ....................................... 10-10
10-3-10. VIDEO OUT 3 Y Level Adjustment ..................................... 10-10
10-3-11. ENC SC Leak Adjustment ..................................................... 10-11
10-3-12. U-V Axis (B-Y, R-Y) Phase Adjustment ............................... 10-12
10-3-13. PB VIDEO OUT 1 Chroma/Burst Level Adjustment ............ 10-13
10-3-14. PB S VIDEO Chroma Level Adjustment ............................... 10-15
10-3-15. PB COMPOSITE C/C Delay Adjustment .............................. 10-15
10-3-16. PB COMPOSITE Y/C Delay Adjustment ............................. 10-16
10-3-17. PB COMPONENT Y/C Delay Adjustment ........................... 10-17
10-3-18. PB INT SCH Phase Adjustment ............................................ 10-18
10-3-19. REF. VIDEO OUT Sync/Burst Level Adjustment ................ 10-19

DSR-2000/2000P

10-3-20. REF. INT SCH Phase Adjustment ......................................... 10-20
10-3-21. SPCK Error Adjustment ......................................................... 10-21
10-3-22. COMPOSITE 4Fsc PLL DC Check/Adjustment ................... 10-22
10-3-23. REC Y Clamp Level Adjustment ........................................... 10-23
10-3-24. REC Y Level Adjustment ...................................................... 10-24
10-3-25. REC COMPONENT R-Y Level Adjustment ........................ 10-25
10-3-26. REC COMPONENT B-Y Level Adjustment ........................ 10-25
10-3-27. REC A/D Y Level Adjustment .............................................. 10-26
10-3-28. REC COMPOSITE Y Level Adjustment ............................... 10-27
10-3-29. REC COMPOSITE Chroma Level Adjustment ..................... 10-28
10-3-30. REC S VIDEO Chroma Level Adjustment ............................ 10-29
10-3-31. REC COMPOSITE Y/C Delay Adjustment .......................... 10-30
10-3-32. REC COMPONENT Y/C Delay Adjustment ........................ 10-31
10-3-33. REC S VIDEO Y/C Delay Adjustment ................................. 10-32
10-4. SDI/SDTI ................................................................................................ 10-33
10-4-1. Free Run Adjustment ............................................................. 10-33

DSR-2000/2000P

Manual Structure
Purpose of this manual
This manual is the Service Manual Volume 1 for the digital videocassette recorder
DSR-2000/2000P, the option boards i.LINK/DV Input/Output Board DSBK-190 and
optional Remote Control Panel DSBK-200.
This manual contains the maintenance information of this equipment, and servicing
information necessary for parts replacement and adjustments.

Related manuals
In addition to this Service Manual Volume 1, the following manuals are provided.
. Operation Instructions
DSR-2000/2000P (Supplied with equipment)
Part number:3-867-754-12 (English; for UC, CE)
3-867-754-22 (French; for UC, CE)
3-867-754-32 (German; for CE)
3-867-754-42 (Italian; for CE)
DSBK-190 (Supplied with Model DSBK-190)
Part number:3-203-674-01
DSBK-200 (Supplied with Model DSBK-200)
Part number:3-203-675-01
DSBK-210 (Supplied with Model DSBK-210)
Part number:3-205-213-01 (1)
. Service Manual Volume 2 (Not Supplied with equipment)
Contains the semiconductor pin assingnments, parts lists, block diagrams, board
layouts and schematic diagrams.
Part number:9-955-186-22
. DSBK-210
Service Manual (Not Supplied with equipment)
Contains the maintenance information of the DSBK-210, and servicing information necessary for parts replacement and adjustments.
Part number:9-955-268-01
. “Semiconductor Pin Assignments” CD-ROM (Available on request)
This “Semiconductor Pin Assignments” CD-ROM allows you to search for
semiconductors used in B&P Company equipment.
Semiconductors that cannot be searched for on this CD-ROM are listed in the
service manual for the corresponding unit. The service manual contains a complete list of all semiconductors and their ID Nos., and thus should be used together
with the CD-ROM.
Part number: 9-968-546-XX

DSR-2000/2000P

Contents
The following is a summary of all the sections for understanding the contents of
this manual.
Section 1 Operating Instruction
Describes the contents of the operating instructions.
Section 2 Installation
This section is described in Installation Manual.
Section 3 Service Overview
Describes the replacement of the parts, the locations of the main parts and boards,
notes and so on.
Section 4 Error Messages
Describes the alarms and countermeasures to be displayed when the unit detects
abnormality.
Section 5 Maintenance Menu
Describes the maintenance menu.
Section 6 Periodic Inspection and Maintenance
Describes the periodic inspection and cleaning procedure.
Section 7 Replacement of Mechanical Parts
Describes the replacement procedures and adjustment after replacement.
Section 8 Tape Path Alignment
Describes the adjustment procedures of tape path system.
Section 9 Electrical Alignment After Replacement Boards
Describes the electrical adjustments after replacement boards.
Section 10 Electrical Alignment
Describes the electrical adjustment of each board.

DSR-2000/2000P

Operating Instructions
Before operating the unit, please read this manual
thoroughly and retain it for future reference.

1-1

1-1. DSR-2000

 1999 by Sony Corporation

This section is extracted
from operation manual.

DSR-2000/2000P

Section 1
Operating Instructions

Digital
Videocassette
Recorder

1-1. DSR-2000

DSR-2000/2000P

3-867-754-12(1)

Owner’s Record
The model and serial numbers are located in the rear.
Record these numbers in the spaces provided below. Refer
to them whenever you call upon your Sony dealer regarding
this product.
Model No.

Serial No.

WARNING
To prevent fire or shock hazard, do not
expose the unit to rain or moisture.

For customers in the USA
This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own
expense.

Caution
Television programs, films, video tapes and other materials
may be copyrighted.
Unauthorized recording of such material may be contrary to
the provisions of the copyright laws.

This symbol is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.

Chapter 1

Overview

For the customers in Europe (DSR-2000P only)
This product with the CE marking complies with both the
EMC Directive (89/336/EEC) and the Low Voltage Directive
(73/23/EEC) issued by the Commission of the European
Community.
Compliance with these directives implies conformity to the
following European standards:
• EN60065: Product Safety
• EN55103-1: Electromagnetic Interference (Emission)
• EN55103-2: Electromagnetic Susceptibility (Immunity)
This product is intended for use in the following
Electromagnetic Environment(s):
E1 (residential), E2 (commercial and light industrial), E3
(urban outdoors) and E4 (controlled EMC environment, ex.
TV studio).

Features ............................................................................. 7
System Configuration .................................................... 11
Location and Function of Parts ..................................... 12
Upper Control Panel ............................................................. 13
Lower Control Panel ............................................................ 16
Subsidiary Control Panel ..................................................... 25
Connector Panel ................................................................... 28
Usable Cassettes ............................................................ 33

You are cautioned that any changes or modifications not
expressly approved in this manual could void your authority
to operate this equipment.
The shielded interface cable recommended in this manual
must be used with this equipment in order to comply with the
limits for a digital device pursuant to Subpart B of Part 15 of
FCC Rules.

This symbol is intended to alert the user to the
presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of
electric shock to persons.

1-1. DSR-2000

1-2

Table of Contents

Inserting and Ejecting Cassettes .......................................... 34

Chapter 2

Setting/Displaying
Time Data and Text
Information

Displaying Time Data and Unit’s Operating Status—
Superimposing Text Information ............................ 35
Setting Time Code and User Bits .................................. 39
Synchronizing the Internal Time Code Generator With an
External Signal—External Lock ..................................... 42

Chapter 3

Recording and
Playback

Recording ........................................................................ 45
Preparations for Recording .................................................. 45
Recording Time Code and User Bit Values .......................... 47
Recording Operation ............................................................ 48
Playback .......................................................................... 49
Preparations for Playback .................................................... 49
Playback Operation .............................................................. 50
Dynamic Motion Control (DMC) Playback......................... 55
Synchronous Playback ......................................................... 59
Digitally Dubbing Signals in DVCAM Format
(Optional DSBK-190 Required When Using i.LINK
Interface) ........................................................................... 61

DSR-2000/2000P

Table of Contents

DSR-2000/2000P

Table of Contents

Chapter 4

Editing

Chapter 5
Automatic Editing ........................................................... 67

ClipLink Operation

Overview of ClipLink Operation .................................... 97
Displaying ClipLink Log Data ........................................ 98

Overview of Automatic Editing ........................................... 67
Button/Switch Settings for Editing ...................................... 70

Detailed Data Display .......................................................... 98

Selecting an Edit Mode ........................................................ 71

Cuing Up to Mark IN/OUT and Cue Points .................... 99

Setting Edit Points ................................................................ 72

Cuing Up to Any Desired Position ....................................... 99

Checking Edit Points ............................................................ 75

Cuing Up to Adjacent Mark IN/Cue Points ......................... 99

Modifying Edit Points .......................................................... 76

Rewriting ClipLink Log Data ........................................ 100

Cuing Up to Edit Points ....................................................... 78

Changing the Reel Number ................................................ 100

Checking Edit Results—Preview ......................................... 80

Changing Mark IN/OUT Points ......................................... 100

Executing Automatic Editing ............................................... 81

Changing the OK/NG Status .............................................. 101

DMC Editing .................................................................... 84

Adding to/Deleting From ClipLink Log Data .............. 103

Overview of DMC Editing ................................................... 84

Adding Mark IN/OUT Points ............................................ 103

Carrying Out DMC Editing.................................................. 85

Deleting Mark IN/OUT Points ........................................... 103

Preread Editing ............................................................... 87

Automatically Creating New ClipLink Log Data ......... 105

Special Editing Methods ................................................ 89
Quick Editing ....................................................................... 90
Continuous Editing .............................................................. 91
Standalone Editing ............................................................... 93

Chapter 6

Setup Menu

Menu System Configuration ........................................ 107
Basic Menu .................................................................... 107

Manual Editing ..................................................................... 94

Items in the Basic Menu..................................................... 107

Adding a Narration (Sound-on-Sound) ................................ 95

Basic Menu Operations ...................................................... 110
Extended Menu ............................................................. 113
Items in the Extended Menu .............................................. 113
Extended Menu Operations ................................................ 123

Table of Contents

1-3

1-1. DSR-2000

Chapter

Chapter 7

Connections and
Settings

Reference Video Signals for Analog Signal Editing .. 125
Connections for Cut Editing Using i.LINK Interface
(Optional DSBK-190 Required) ...................................... 125

Chapter 1 Overview

Overview

Connections for Digital Nonlinear Editing Using SDTI
(QSDI) Interface ...................................................... 127
Connections for Cut Editing Using SDI Interface ...... 128
Connections for Preread Editing ................................ 129
Settings Required When Connecting an External
Editing Control Unit ................................................ 130
Time Code Settings on This Unit ....................................... 130
Settings on Editing Control Units ...................................... 130
Connections for Component Analog Recording ....... 131

Features

Connections for Two-Unit Synchronous Playback .... 132
Connections for Digitally Dubbing Signals in DVCAM
Format (Optional DSBK-190 Required When Using
i.LINK Interface) .............................................................. 133

Chapter 8

Maintenance and
Troubleshooting

Condensation ................................................................ 135
Head Cleaning ............................................................... 135
Periodic Maintenance ................................................... 136
Troubleshooting ............................................................ 137
Error Messages ................................................................... 139
Alarm Messages ................................................................. 139

The DSR-2000/2000P is a 1/4-inch digital videocassette
recorder using the DVCAMTM digital recording format.
It uses a component video system, with separate
luminance and chrominance signals and digital
processing to realize a stable, high image quality.
This unit is equipped with a variety of functions
needed for videocassette recorders and players used in
video editing. By combining two units, you can easily
assemble a cut editing system. It is also equipped with
full-fledged analog and digital interfaces to support
hybrid systems that combine conventional analog
equipment with digital equipment. Furthermore, it
supports the Sony-developed ClipLinkTM function,
improving operating efficiency when combined with a
Sony EditStationTM.
The following are the principal features of the unit.

Appendixes
Notes on Use ................................................................. 143
ClipLinkTM Guide ........................................................... 147
What is ClipLink? .............................................................. 147
Example System Configuration and Operation Flow ........ 148

Wide track
The recording track width is 15 µm, 50% wider than
the 10 µm of the DV format. This ensures adequate
reliability for professional use.

PCM digital audio for high sound quality
The PCM encoding method yields a high audio
quality, with wide dynamic range and high signal-tonoise ratio.
There are two recording modes: two-channel mode
(48-kHz sampling and 16-bit quantization), which
offers sound quality equivalent to the DAT (Digital
Audio Tape) format, or four-channel (32-kHz
sampling and 12-bit quantization).

DVCAM Format

Specifications ............................................................... 144
DVCAM is a professional 1/4-inch digital recording
format developed by Sony from the consumer DV
component digital format (4:1:1 for DSR-2000/4:2:0
for DSR-2000P).

Playback compatibility with DV and
DVCPRO formats
A DV cassette recorded on a DV format VCR as well
as a DVCPRO(25M) format recorded cassette can be
played back on this unit.

Data Generated When Shooting ......................................... 149
Glossary ........................................................................ 152
Index .............................................................................. 155

DSR-2000/2000P

Table of Contents

1-1. DSR-2000

1-4
Table of Contents

High image quality and high stability
The luminance and chrominance signals are encoded
separately, with a 1/5 compression, giving a stable high
quality video image.
Since this is a digital system, nth-generation copies
created by repeated dubbing show virtually no loss in
picture quality.

Note

When playing back a tape recorded in DVCPRO
(25M) format, the SDTI and i.LINK outputs (see the
section “Digital interfaces” on the next page) of this
unit are muted. Furthermore, it is not possible to
playback the cue-audio track of the tape.
Chapter 1

Overview

DSR-2000/2000P

Features
Location and Function of Parts

Support for three cassette sizes

Variety of Interfaces

Analog interfaces
A wide range of analog interfaces is provided,
allowing this unit to be connected to various video and
audio devices.
• Analog video: Composite, component and S-video
interfaces are provided.
• Analog audio: There are four input channels and
four output channels. There is also support for
microphone input.

Split editing
In insert editing, this allows the audio IN and OUT
points to be set separately from the video IN and OUT
points.
Preread editing
The audio or video on the tape can be read out using
the preread heads. The signals then can be processed
and rerecorded where they have been.
Cross-fade editing
For audio editing, you can select from cut-in editing,
fade-in/fade-out editing, and cross-fade editing.

Connection to external control devices

The unit can use the following digital interfaces.
It is possible to connect a PVE-500, RM-450/450CE,
• SDTI (QSDI)1)
FXE-100/100P/120/120P, BVE-900/910/2000/9000/
This interface allows video, audio and time code
9000P/9100/9100P or other editor equipped with an
signals in SDTI (QSDI) format to be transferred at
RS-422A interface, or a UVR-60/60P remote
normal speed between this unit and the ES-7
controller for the built-in digital video processor, and
EditStation. When this unit is connected to another
so forth.
DVCAM VCR, it is possible to copy compressed
signals between the two VCRs.
• SDI2)
Full Functionality for More
This interface allows the unit to input or output D1
Efficient Editing
(component) digital video and audio signals.
• AES/EBU
This unit has a number of functions which assist in
This interface allows the unit to input or output
efficient and precise editing.
digital audio signals in AES/EBU format.
With two DSR-2000/2000P units together, you can
• i.LINK (DV)3) (Optional DSBK-190 i.LINK/DV
carry out automatic or manual editing, using either
Input/Output Board)
assemble or insert editing.
When the unit is fitted with the optional DSBK-190
The system also provides a powerful range of
i.LINK/DV Input/Output Board using i.LINK
functions for setting and amending edit points,
technology, it can input and output digital video and
preview, review, and other aspects of efficient editing.
audio signals in DV format.
• SDTI-CP output (Optional DSBK-210 SDTI-CP
DMC (dynamic motion control) editing
Output Board)
You can save a varying speed, in the range −1 to +1
This interface allows the unit to provide an output of
times
normal speed4), for an editing segment, and
I-frame pictures only (50/40/30 Mbps) complying to
automatically edit with this varying speed.
MPEG2 4:2:2 Profile @Main Level. You can connect
the unit to an MPEG supporting device equipped with
an SDTI-CP input.
.........................................................................................................................................................................................

Chapter 1

Overview

This unit accepts instructions from an EditStation, to
transfer to the EditStation ClipLink log data held in the
cassette memory or index pictures recorded on the
tape. On the EditStation you can use these images and
data to carry out editing operations efficiently.
• Displaying ClipLink log data
• Changing ClipLink log data OK/NG status
• Cuing up to Mark IN and cue points provided by
ClipLink log data
• For cut editing, copying Mark IN data from ClipLink
log data

Using the frame memory function, noiseless slow
motion playback is possible at any speed in the range
+1 to –1 times normal speed.

Digital jog sound function
When searching at speeds in the range +1 to +1/30 or
–1/30 to –1 times normal speed, the digital jog sound
function is enabled. The audio signal is saved in
temporary memory, and replayed according to the
search speed. This allows searching on the sound
track.

For an overview of the ClipLink function, see the appendix
“ClipLink Guide” (page 147).

Video process control

Internal time code generator and reader

For analog video output and SDI-format video output,
you can adjust the video output level, chroma signal
output level, setup level (for DSR-2000), black level
(for DSR-2000P), and chroma phase.

An internal timecode generator and reader enables
timecode compliant with SMPTE/EBU format to be
recorded and played back. This allows editing to single
frame precision.
Outputting or inputting timecode (LTC) to or from an
external device is also possible using the TIME CODE
IN/OUT connectors.
The unit is also compatible with VITC.

2) SDI: Serial Digital Interface is used for transferring video
signals in component digital format (D1).
3) is a trademark of Sony Corporation and indicates that
this product is in agreement with IEEE1394-1995
specifications and their revisions.
4) The positive direction refers to forward movement of the
tape, and the negative direction to reverse movement.
Chapter 1 Overview

1-5

1-1. DSR-2000

1) SDTI (QSDI): SDTI (Serial Data Transport Interface) is
the name of a standard interface established as SMPTE
305M.
This unit uses SDTI to transmit DV data, and the input/
output connectors are labled “SDTI(QSDI)”.
In indicator and menu indications, however, the
“SDTI(QSDI)” name is shortened to “SDTI”.

You can carry out a picture search while playing back
in color within the range +60 to –60 times normal
speed.
When controlling the unit in shuttle mode from an
editor or remote control unit, you can search at any
speed in the range +60 to –60 times normal speed. In
jog mode a frame by frame search is possible. During
playback in the range +10 to –10 times normal speed,
high-speed audio playback is also possible.

Digital slow motion playback
Support for ClipLink function

Digital interfaces

High-speed search function

Chapter 1 Overview

There are two sizes of DVCAM cassette: standard and
mini. You can use either size with this unit.
The unit also accepts L and M sizes of DVCPRO
cassette.
• The reel mechanism automatically adjusts to the size
of cassette inserted.
• The capacity of a standard cassette is 184 minutes of
recording/playback, and that of a mini cassette is 40
minutes.

Note

You cannot install both of the DSBK-190 and DSBK210 on the unit at a time.

Other Features

To make it easier to use this unit for any particular
purpose, various functions and operating settings are
provided in the menu system.

Options

The figure below shows example equipment that can
be connected to this unit.

DSBK-190 i.LINK/DV Input/Output Board
This board enables cut editing between two DSR2000/2000P units. It also allows you to connect the
unit to other equipment provided with a Sony DV
connector to carry out editing or dubbing of digital
video and audio signals.

SDI INPUT/OUTPUT

DVCAM cassette
DVCAM camcorder
DNW-A75/A75P

Superimposing function
DSBK-200 Control Panel
Timecode, operating mode, error messages, and other
text information, can be superimposed on the SDI
video signal and analog composite video signal output.

DV cassette

DV camcorder

When connected to the unit, you can operate the unit
remotely from the DSBK-200.

Functions for easy maintenance

RMM-130 Rack Mount Kit

• Self-diagnosis and alarm function: This
automatically detects incorrect operations or
connections, operating faults, and so forth, and
displays details of the problem, the cause, and the
action to be taken, in the control panel display
section.
• Digital hours meter: This keeps four cumulative
counts of the powered on time, the drum rotation
time, the tape transport time, and the number of tape
threadings and unthreadings, and displays them in the
control panal display section.

This kit can be used to mount the unit in an EIAstandard 19-inch rack.

Chapter 1 Overview

Menu operations for functions and
operating settings

1-1. DSR-2000

1-6

System Configuration

Features
Location and Function of Parts

SDTI(QSDI)
INPUT/OUTPUT
i.LINK
(DSBK-190)a)

DV camcorder

DSR-60/60P/80/80P/85/85P
Digital VCR

SDTI(QSDI)
INPUT/OUTPUT

DSBK-210 SDTI-CP Output Board
DSR-500WS/500WSP

This board enables the unit to be connected to an
MPEG supporting device (MSW-2000, MAV-555, and
so on).

i.LINK
(DSBK-190)a)

COMPONENT
VIDEO IN/OUT

ANALOG VIDEO I/O
S VIDEO IN/OUT

ES-7/ES-3 Edit Station

DSR-2000/2000P (this unit)

Compatible with wide screen aspect ratio
(16:9)
SVO-5800/5800P

The unit can record and play back aspect ratio
information. When video accompanied by wide-screen
aspect ratio information is recorded or played back, the
unit can output the video signal also containing the
aspect ratio information.

Analog Betacam VCR

Microphone

Video monitor

Rack mountable
Using the optional RMM-130 Rack Mount Kit, you
can mount the unit in an EIA standard 19-inch rack
(height: 4 units).

DSR-2000/2000P

Chapter 1 Overview

Headphones

a) The DSBK-190 is an optional board.

Audio monitor system

Chapter 1 Overview

DSR-2000/2000P

Location and Function of Parts

There are four control panels as shown in the figure
below.

Upper Control Panel

Chapter 1 Overview

1 POWER switch
2 Audio level meters
Connector panel (See page 28.)

Lower control panel (See page 16.)

3 Cassette compartment

1 Input selection/audio mode display section
(see below)
2 Input selection section
(see page 14)

Upper control panel (See page 13.)

POWER

dB OVER dB
0
2

-12

-20

-2

-30
-40

-2

-30
-40

-2

-30
-40

-2

-60

-30
-40
-60

-1

3 Remote control
setting section
(see page 15)

INPUT SELECT
SDTI/i.LINK
INPUT

V:SDTI

SDTI

COMPOSITE Y-R,B S VIDEO

SDI SG

ANALOG

AES/EBU

SDI SG

ANALOG

AES/EBU

SDI SG

PB FS

48k44.1k32k

REC MODE

REMOTE

i.LINK

VIDEO
CH11/2
AUDIO
CH23/4

VIDEO IN
9PIN

CH-1,1/2
CH-2,3/4

i.LINK

2CH4CH

MIXING

Subsidiary control panel (See page 25.)

1 POWER switch
Press the “1” side to power the unit on. When the unit
is powered on, the display windows in the upper and
lower control panels light.
To power the unit off, press the “¬”side of the switch.

To adjust the position of the lower control
panel
You can fix the lower control panel in any position
between vertical and horizontal for ease of operation.

Handle
If you raise the panel to the horizontal, it
automatically locks in position.
Lock knob

3 Cassette compartment
Accepts DVCAM, DV and DVCPRO(25)
videocassettes.
For details of usable cassettes, see page 33.

2 Audio level meters
These show the audio levels of channels 1 to 4
(recording levels in recording mode or E-E mode1) and
playback level in playback mode).
There are two modes for audio level indications:
FULL and FINE, selected by the METER FULL/FINE
button on the lower control panel.

1 Input selection/audio mode display section
When the panel is at the desired angle,
turn both lock knobs to fix in position.
Release lever

To lower the panel, press both
release levers.

Raise the panel by holding both ends or
both handles.

1 INPUT display

INPUT

V:SDTI

SDTI

i.LINK

2 INPUT VIDEO display

VIDEO

COMPOSITE Y-R,B S VIDEO

SDI SG

3 AUDIO CH1, 1/2 display

CH11/2
AUDIO
CH23/4

ANALOG

AES/EBU

SDI SG

ANALOG

AES/EBU

4 AUDIO CH2, 3/4 display
5 PB FS display

PB FS

48k44.1k32k

REC MODE

SDI SG
2CH4CH

6 REC MODE display

To fix the panel at an angle where the lock knobs are inaccessible
1 First position the panel at the desired angle, then without tightening the lock knobs, press the release levers
and raise the panel to the horizontal.
2 With the panel horizontal, tighten the lock knobs, then press the release levers and return the panel to the
desired position, where it will lock into place.

.........................................................................................................................................................................................

Chapter 1 Overview

but not through magnetic conversion circuits such as
heads and tapes. This can be used to check input signals
and for adjusting input signal levels.
Chapter 1 Overview

1-7

1-1. DSR-2000

1) E-E mode: Abbreviation of “Electric-to-Electric mode”.
In this mode, video and audio signals input to the VCR
are output after passing through internal electric circuits,

1-1. DSR-2000

1-8
Location and Function of Parts

2 INPUT VIDEO display
Indicates the input video signal selected with the
VIDEO IN button in the input selection section.
COMPOSITE: Composite video signal
Y-R, B: Y, R−Y and B−Y component video signals
S VIDEO: S-video signal
SDI: SDI video signal
SG: Video test signal
3 AUDIO CH1, 1/2 display
Indicates the input audio signal selected with the CH1,
1/2 button in the input selection section.
ANALOG: Analog audio signal
AES/EBU: Digital audio signal in AES/EBU format
SDI: SDI audio signal
SG: Audio test signal
4 AUDIO CH2, 3/4 display
Indicates the input audio signal selected with the CH2,
3/4 button in the input selection section. The
indications available are the same as for the AUDIO
CH1, 1/2 display described above.
5 PB FS (playback audio sampling frequency)
display
Indicates the sampling frequency (48 kHz, 44.1 kHz or
32 kHz) at which audio is recorded on tape.
6 REC MODE (audio recording mode) display
Indicates the audio recording mode (2CH or 4CH)
selected with extended menu item 818.

DSR-2000/2000P

Chapter 1 Overview

2 Input selection section

1 SDTI/i.LINK button

INPUT SELECT
SDTI/i.LINK

2 VIDEO IN button

VIDEO IN

3 CH1, 1/2 button

CH-1,1/2

4 CH2, 3/4 button

CH-2,3/4

5 MIXING button

MIXING

1 SDTI/i.LINK (SDTI(QSDI) interface/i.LINK
selection) button
Each press of this button cycles through the following
input signal selection options.
• Digital video signal in SDTI(QSDI) format input to
the SDTI(QSDI) INPUT connector
When this is selected, use the CH1, 1/2 button and
CH2, 3/4 button to select the required input audio
signals.
• Digital video and audio signals in SDTI(QSDI)
format input to the SDTI(QSDI) INPUT connector
• Digital video and audio signals in DV format, using
i.LINK technology, input to the i.LINK connector
(available when the optional DSBK-190 i.LINK/DV
Input/Output Board is installed)
In the input selection/audio mode display section, the
INPUT display shows the selection made with this
button.
2 VIDEO IN button
Each press of this button cycles through the following
input video signal selection options.
• Composite video signal input to the VIDEO IN
connectors.
• Component video signals input to the COMPONENT
VIDEO Y/R−Y/B−Y IN connectors
• S-video signal input to the S VIDEO IN connector
• SDI video signal input to the SDI INPUT connector
• Video test signal (selected with extended menu item
710) generated by the internal signal generator
In the input selection/audio mode display section, the
INPUT VIDEO display shows the selection made with
this button.

3 CH1, 1/2 (audio channel 1 or 1/2) button
Each press of this button cycles through the following
input audio signal selection options for audio channel 1
(when in 2-channel mode) or for audio channels 1 and
2 (when in 4-channel mode).
• Analog audio signal(s) input to the AUDIO IN CH-1
connector (when in 2-channel mode) or AUDIO IN
CH-1 and CH-2 connectors (when in 4-channel
mode).
• Digital audio signal in AES/EBU format input to the
DIGITAL AUDIO (AES/EBU) CH-1/2 connector
• SDI audio signal input to the SDI INPUT connector
• Audio test signal (selected with extended menu item
808) generated by the internal signal generator
In the input selection/audio mode display section, the
AUDIO CH1, 1/2 display shows the selection made
with this button.
4 CH2, 3/4 (audio channel 2 or 3/4) button
Each press of this button cycles through the input audio
signal selection options for audio channel 2 (when in 2channel mode) or for audio channels 3 and 4 (when in
4-channel mode) The input audio signal selection
options corresponding to those for the CH1, 1/2 button
described above are available.
In the input selection/audio mode display section, the
AUDIO CH2, 3/4 display shows the selection made
with this button.
5 MIXING (mixing setting on/off) button
This enables (ON) or disables (OFF) the setting for
audio input mixing made with extended menu item
819.
If the selected signal (except for analog audio) is not
supplied to the appropriate connector, the
corresponding indicator in the input selection/audio
mode display section flashes.

3 Remote control setting section

Chapter 1 Overview

1 INPUT display
Indicates the input signal selected with the SDTI/
i.LINK button in the input selection section.
V:SDTI: Digital video signal in SDTI(QSDI) format
In this mode, you can select any audio input,
though the video signal is recorded with a delay of
two frames with respect to the audio input.
SDTI: Digital video and audio signals in
SDTI(QSDI) format
i.LINK: Digital video and audio signals in DV
format, using i.LINK technology

REMOTE

1 REMOTE button
9PIN

2 9PIN button
i.LINK

3 i.LINK button

1 REMOTE button
When remote-controlling this unit from the unit
connected to the REMOTE-IN, REMOTE-OUT or
i.LINK connector, press this button, turning it on.
2 9PIN button
When carrying out remote control between this unit
and the unit connected to the REMOTE-IN or
REMOTE-OUT connector, press this button, turning it
on.
3 i.LINK button
When carrying out remote control between this unit
and the unit connected to the i.LINK connector, press
this button, turning it on.
This button is effective only when the optional DSBK190 i.LINK/DV Input/Output Board is installed.

Chapter 1 Overview

DSR-2000/2000P

Location and Function of Parts

1 METER FULL/FINE button
Chapter 1 Overview

2 REC controls
3 PB controls
4 MONITOR SELECT buttons
1 Monitor/menu/display setting
section (see page 17)
CH-1

METER

CH-2

CH-3

MONITOR SELECT

CH-4

FULL/FINE

ClipLink

CH-1 CH-2 CH-3 CH-4
PHONE LEVEL REC

2 Display section (see page 18)

PULL FOR VARIABLE

COUNTER
U-BIT TC

LIST

MARK

PREREAD PB/EE

REPEAT

VITC

REC INHIBIT KEY INHIBIT SERVO

SET

SHUTTLE
JOG

NOT
EDITABLE
HOURS

MINUTES

HOLD COUNTER SEL RESET

SECONDS

FRAMES

CHANNEL CONDITION

TRIM

PB
VIDEO

CH-1

INSERT
CH-2 CH-3

CH-4

AUDIO
ASSEMBLE

DELETE

DMC EDIT

PLAYER RECORDER

OUT

STANDBY

PREROLL

EJECT

REW

REC

EDIT

ENTRY SHIFT

MEMORY
HEADPHONES

PREVIEW

AUTO

EDIT

REVIEW

PLAY

F FWD

STOP
SEARCH VARIABLE

OUT

5 Tape transport control
section (see page 22)
4 Editing control section (see page 21)

6 Search control section
(see page 23)
6 PLAYER button and RECORDER button

3 Edit mode setting section (see page 20)
5 HEADPHONES jack and PHONE LEVEL control

1 METER FULL/FINE button
This switches the display mode of the audio level
meters in the upper control panel as follows:
FULL: In this mode the segment of the display
corresponding to the current audio level and all
lower segments light. A marker indicating the
reference level (set with extended menu item 811)
also appears.
FINE: The display is enlarged, with a step of 0.25 dB
with respect to the reference level of 0 dB.
In this mode only the segment of the display
corresponding to the current audio level lights. If
the audio level exceeds the maximum display
level, the top segment flashes, and if the audio
level goes below the minimum display level, the
bottom segment flashes.

Chapter 1 Overview

1 Monitor/menu/display setting section
2 MENU button
3 SET button
PREREAD PB/EE

SET

HOLD COUNTER SEL RESET

1 PREREAD button

4 RESET button
6 PB button
5 PB/EE button

For details of selecting the E-E mode, see the description of
the REC button in the tape transport control section (see
page 22) and the PB/EE button in the monitor/menu/display
setting section (see page 17).

6 PLAYER button and RECORDER button
When you carry out editing using a VCR connected to
the REMOTE-IN or REMOTE-OUT connector as the
player and this unit as the recorder, these buttons select
which VCR the editing control buttons and tape
transport buttons on this unit control.
PLAYER: The editing control buttons and tape
transport buttons on this unit control the external
player VCR.
RECORDER: The editing control buttons and tape
transport buttons on this unit control the recorder
(this unit).
When this unit is being used in standalone mode,
neither button functions.

1 PREREAD button
When this is lit, a preread (read-before-write) is carried
out in insert editing.
For details of preread editing, see the section “Preread
Editing” (page 87).

2 MENU button
Use this button for setup menu operations.
Pressing this button, turning it on, shows setup menus
in the time counter display (see page 18).
Press the button once more to exit from the menu
display.

8 COUNTER SEL button
7 HOLD button

For details of setup menu operations, see Chapter 6 “Setup
Menu” (page 107).

3 SET button
Use this button for setting time code and user bit
values and in setup menu operations.
For details of setting time code and user bit values see
Chapter 2 “Setting/Displaying Time Data and Text
Information” (page 35).

Chapter 1 Overview

1-9

1-1. DSR-2000

2 REC (recording) controls
These individually adjust the recording levels on
channels 1 to 4.
To set the recording level, put the unit in E-E mode,
pull out the control knobs and adjust the level while
watching the level meters.
When the control knobs are pushed in, the recording
levels return to the preset levels and cannot be
adjusted.

4 MONITOR SELECT buttons
There are four buttons CH-1 to CH-4 (channels 1 to 4)
in each of the upper (L) and lower (R) rows. Use these
buttons to select the channels for audio output via the
HEADPHONES connector on the lower control panel
and the MONITOR AUDIO connector on the
connector panel.
The HEADPHONES connector outputs stereo sound
(L and R) and the MONITOR AUDIO connector
outputs monaural sound (L and R mixed).
You can select two or more channels in either row by
pressing the buttons for the desired channels
simultaneously. The sounds of the channels selected in
the row are mixed.
In 2-channel audio recording mode (selected with
extended menu item 818), it is possible to use the
AUDIO OUT CH-3 and AUDIO OUT CH-4
connectors for monitor audio output for channels 1 and
2, respectively (use extended menu item 820).

5 HEADPHONES jack and PHONE LEVEL
control
Connect stereo headphones with an impedance of 8
ohms to monitor the sound during recording, playback
and editing.
The PHONE LEVEL control knob adjusts the volume.

Chapter 1 Overview

3 PB (playback) controls
These adjust individually the playback levels on
channels 1 to 4.
During playback, pull out the control knobs and adjust
the level while watching the level meters.
When the control knobs are pushed in, the playback
levels return to the preset levels, and cannot be
adjusted.

Lower Control Panel

1-1. DSR-2000

1-10
Location and Function of Parts

5 PB/EE (playback/E-E) button
To select E-E mode input signals for the video/audio
signals output during fast forward, rewind, still, and
standby, press this button, turning it on.
Either one of this button and the PB button is always
lit.
6 PB (playback) button
To select playback signals for the video/audio signals
output during fast forward, rewind, still, and standby,
press this button, turning it on.
Either one of this button and the PB/EE button is
always lit.

7 HOLD button
To stop updating of the time code or user bit value in
the time counter display (that is, to hold the display),
press this button, turning it on. To set a time code or
user bit value, first press this button to hold the value.
8 COUNTER SEL (select) button
This switches the value shown in the time counter
display in the following sequence: COUNTER, TC, UBIT.
Time counter display selection

2 ClipLink indicator
Lights when a cassette is loaded on which ClipLink
log data is stored in the cassette memory.

6 REC (recording) INHIBIT indicator
This indicator is on or off according to the
combination of the setting of the REC INHIBIT switch
on the subsidiary control panel and the REC/SAVE
switch on the loaded cassette, as shown in the
following table. When this indicator is on, recording
on tape is prohibited.
REC INHIBIT indicator indications
REC INHIBIT
State of the REC/ REC INHIBIT
switch position SAVE switch on
indicator state
the cassette
ON

SAVE/REC

Lit

OFF

SAVE

Lita)

REC

Off

Selection

Value displayed

COUNTER

Tape running time (hours, minutes,
seconds, frames)

Playback time code read by the internal
time code reader or time code being
recorded.a)

For details of ClipLink log data, see the appendix “ClipLink
Guide” (page 147).

a) It is possible to make a setting (extended menu item 107)
so that in this case the indicator flashes.

U-BIT

User bit value inserted in the playback time
code or time code being recorded.a)

3 VITC indicator
Regardless of the data shown in the time counter
display, this indicator lights when VITC in the signal
played back or in the input video signal (in E-E mode)
is being read.

7 Cassette memory indicator
Lights when a cassette provided with a memory chip
(“cassette memory”) is loaded.

a) The selection of TC or VITC is made by the TC SELECT
switch on the subsidiary control panel.

2 Display section

1 Recording/playback format indicators
2 ClipLink indicator
3 VITC indicator
4 Time data type indicators

5 Time counter display

9 SERVO indicator
8 KEY INHIBIT indicator
7 Cassette memory indicator

1 Recording/playback format indicators
DVCAM: This lights when a tape recorded in
DVCAM format is played back.
DV: This lights when a tape recorded in consumer
DV format is played back.
LP: This lights when a tape recorded in LP mode is
played back.
When a tape recorded in DVCPRO (25) format or any
other format than those mentioned above is played
back, none of the above indicators lights.

!º CHANNEL CONDITION indicator

4 Time data type indicators
One of the three indicators (COUNTER, U-BIT, and
TC) lights to indicate the type of time data currently
shown in the time counter display.
COUNTER: Count value of the time counter
U-BIT: User bit data
TC: SMPTE time code (DSR-2000) or EBU time
code (DSR-2000P)
5 Time counter display
Indicates the count value of the time counter, time
code, or user bit data depending on the settings of the
COUNTER SEL button in the monitor/menu/display
setting section and the TC SELECT switch on the
subsidiary control panel.
Also used to display edit point values, edit duration
values, error messages and setup menu data.

8 KEY INHIBIT indicator
This indicator lights when the KEY INHIBIT switch
on the subsidiary control panel is set to ON.
The buttons/switches to be operable even when this
indicator is on can be determined using extended menu
item 118.
9 SERVO indicator
When the drum servo and capstan servo are locked1),
this indicator lights.
!º CHANNEL CONDITION indicator
This three-color indicator shows the state of the
playback signal.
Green: The state of the playback signal is good.
Yellow: The playback signal is somewhat
deteriorated, but playback is possible.
Red: The playback signal is deteriorated.
When the red indicator remains on, head cleaning
or an internal inspection is necessary.

6 REC INHIBIT indicator
!¡Tape end alarm indicator

!™ SHUTTLE/JOG indicators

DSR-2000/2000P

!£ NOT EDITABLE indicator

Chapter 1 Overview

.........................................................................................................................................................................................
1) Servo lock: This refers to the synchronization of the
phase of the drum rotation and the reference signal for the
tape transport position, so that the video heads can trace
the same pattern on the tape for playback or recording.
Chapter 1 Overview

Chapter 1 Overview

4 RESET button
To reset a time counter value (COUNTER) shown in
the time counter display, press this button.
Resetting the COUNTER value erases all edit points.
This button is also used for setting time code and user
bit values and in setup menu operations.

DSR-2000/2000P

Location and Function of Parts

!¡ Tape end alarm indicator
Starts flashing when the remaining capacity of the tape
is for about 2 minutes.

For more information about the search dial, see page 23.

!£ NOT EDITABLE indicator
Lights during playback of a tape that contains a
recording in other than the DVCAM format. When
this indicator is lit, the recordings contained in the tape
can be used as source material for editing, but editing
operations such as insert editing and assemble editing
cannot be performed.
This indicator also lights when the audio recording
mode selected on this unit does not coincides with that
of the loaded tape.

1 DELETE button

1 INSERT buttons

LIST

VIDEO

CH-1

INSERT
CH-2 CH-3

2 MEMORY indicator
CH-4

7 AUDIO IN button and AUDIO OUT button

AUDIO
DELETE

DMC EDIT

ENTRY SHIFT

MEMORY

3 DMC EDIT button
ASSEMBLE
PREVIEW

AUTO

EDIT

8 ENTRY/SHIFT button
REVIEW

OUT

4 PREVIEW button

9 IN button and OUT button

5 AUTO EDIT button

!º REVIEW button

2 ASSEMBLE button

1 INSERT buttons
Use these buttons to select the signals for insert
editing1).
VIDEO: To select the video signal, press this button,
turning it on.
CH-1 to CH-4 (channel 1 to channel 4): To select
audio channels 1 to 4, press these buttons, turning
them on. You can select any number of the
channels.
TC: To select time code, press this button, turning it
on.

.........................................................................................................................................................................................

1 DELETE button
This deletes an existing edit point.
Hold down this button and press the IN, OUT, AUDIO
IN, or AUDIO OUT button which is lit, indicating an
existing edit point. The button either goes off or
flashes and the corresponding edit point is deleted.
When the button flashes, it is necessary to set the
deleted edit point again.

5 AUTO (automatic) EDIT button
After setting edit points, to carry out automatic editing
(recording), press this button, turning it on.
If the IN point is not set, the automatic editing is
carried out with the point where you pressed this
button as the IN point.
If you pressed the PREVIEW button to carry out a
preview, when the preview ends this button flashes.

2 MEMORY indicator
When memorizing the playback speed using the DMC
EDIT button, this indicator flashes as the playback
speed is captured to memory, and lights continuously
once the speed is captured.

6 TRIM buttons
Use these buttons to trim an edit point to single-frame
precision.
Hold down the IN, OUT, AUDIO IN, or AUDIO OUT
button, and press one of these buttons. The MARK/+
button advances the corresponding edit point by one
frame, and the LIST/− button sets it back by one
frame.
During playback, pressing one of these buttons while
holding down the PLAY button adjusts the tape speed
by +8% or −8%, correspondingly. (Capstan override
function)
These buttons are also used for ClipLink operations
and setup menu operations.

3 DMC EDIT button
Use this button to memorize the playback speed varied
between ±1 times normal speed and carry out
automatic playback or automatic editing using the
memorized playback speed.

2) Assemble editing: Editing in which new video/audio is
added in sequence to the end of existing recorded video/
audio.

4 PREVIEW button
After setting edit points, to preview the editing results
before carrying out the edit, press this button, turning it
on.
If the IN point is not set, the preview is carried out
with the point where you pressed this button as the IN
point.
During the preview the button is lit, and when the
preview ends it flashes.

For more information about ClipLink operations and setup
menu operations, see Chapter 5 “ClipLink Operation”
(page 97) and Chapter 6 “Setup Menu” (page 107),
respectively.

7 AUDIO IN button and AUDIO OUT button
In insert editing, to set an audio IN point or audio OUT
point separate from the corresponding video edit point,
hold down the AUDIO IN button or AUDIO OUT
button, and press the ENTRY/SHIFT button.
After you have made the setting, pressing the AUDIO
IN button or AUDIO OUT button displays the audio
IN point or audio OUT point set on the time counter
display.
Chapter 1 Overview
21

1-11

1-1. DSR-2000

Chapter 1 Overview

6 TRIM buttons

For information about how to carry out DMC playback or
DMC editing using this button, see the section “Dynamic
Motion Control (DMC) Playback” (page 55) and “DMC
Editing” (page 84), respectively.

+
OUT

2 ASSEMBLE button
Press this button, turning it on, to carry out assemble
editing2).
All signals (video signals, audio signals, time code
signals, and so forth) are recorded together.

1) Insert editing: Editing in which new video/audio is added
into the middle of existing recorded video/audio.

MARK

TRIM

Chapter 1 Overview

!™ SHUTTLE/JOG indicators
When searching in shuttle or variable mode using the
search dial, the SHUTTLE indicator lights, and when
searching in jog mode using the search dial, the JOG
indicator lights. When the search dial is turned
clockwise causing playback to take place in the
forward direction, the · indicator lights. When the
search dial is turned counterclockwise causing
playback to take place in the reverse direction, the ª
indicator lights. When the tape is stopped, the π
indicator lights.

4 Editing control section

3 Edit mode setting section

1-1. DSR-2000

1-12
Location and Function of Parts

For more information about ClipLink operation, see
Chapter 5 “ClipLink Operation” (page 97).

9 IN button and OUT button
To set a video IN point or OUT point, hold down the
IN button or OUT button, and press the ENTRY/
SHIFT button.
After you have made the setting, pressing the IN
button or OUT button displays the IN point or OUT
point on the time counter display.
!º REVIEW button
Use this button to carry out a review of the editing
results after carrying out automatic editing.

5 Tape transport control section
1 STANDBY button
2 PREROLL button

STANDBY

PREROLL

EJECT

REW

3 REC button
4 EDIT button
REC
EDIT

5 STOP button
PLAY

F FWD

STOP

9 F FWD button

1 STANDBY button
When a cassette is inserted and this button is off, to put
the VCR in standby mode, press the button, turning it
on.
In standby mode, the drum is rotating and the tape is in
contact with the drum. As a result, recording or
playback can start immediately.
To end standby mode, press the STANDBY button,
turning it off.
If a certain period of time (value can be varied using
extended menu item 501) elapse in standby mode, the
unit automatically switches out of standby mode to
protect the tape.
2 PREROLL button
Press this button to cue up to the preroll point (before
the IN point by the time set as the preroll time) on the
tape. You can change or select the preroll time and the
state of the unit at the end of preroll (stop mode1) or
still playback mode) using basic menu item 001 and
extended menu item 401.

3 REC (record) button
To start recording, press this button together with the
PLAY button, turning it on.

6 EJECT button
To eject the cassette, press this button. While the
cassette is being ejected, this button lights.

Monitoring in E-E mode
When the unit is in stop mode, pressing this button
lights it, and you can monitor the video and audio in EE mode. To return to the original state, press the STOP
button.
During playback, search, fast forward, or rewind,
holding down this button allows you to monitor the
video and audio in E-E mode. In this case the button
does not light.

7 REW (rewind) button
To rewind the tape, press this button, turning it on.

6 EJECT button

.........................................................................................................................................................................................

DSR-2000/2000P

Chapter 1 Overview

5 STOP button
To stop recording or playback, press this button,
turning it on.
When you stop playback, the unit switches either to
still playback or to E-E mode according to setup menu
settings, and the settings of the PB/EE button and PB
button.
Fault display function
This button flashes when there is no external reference
signal input or the input external reference signal is not
synchronized to the input video signal. (See the
description of extended menu item 105.)

8 PLAY button

Monitoring in E-E mode
When the unit is in stop mode, pressing this button
lights it, and you can monitor the input signal selected
with the ASSEMBLE button or INSERT buttons in EE mode. To return to the original state, press the STOP
button. During playback, search, fast forward, or
rewind, holding down this button allows you to
monitor the video in E-E mode.

Cuing up to edit points
Hold down the IN, OUT, AUDIO IN, or AUDIO OUT
button while pressing this button to cue up to the
corresponding edit point.

7 REW button

1) Stop mode: the state in which the device currently the
subject of operation is stopped, and the STOP button is
lit.

4 EDIT button
To carry out manual editing, press this button
simultaneously with the PLAY button.

8 PLAY button
To start playback, press this button, turning it on.
To operate in capstan override mode
Hold down this button, and turn the search dial.
For details of capstan override mode, see “3 Search dial”
on this page.

9 F FWD (fast forward) button
To fast forward the tape, press this button, turning it
on.

6 Search control section

Chapter 1 Overview

8 ENTRY/SHIFT button
Use this button for setting edit points, carrying out
ClipLink operations, and so forth.
• To set a video IN point or OUT point: Hold down the
IN button or OUT button, and press this button.
• To set an audio IN point or OUT point: Hold down
the AUDIO IN button or AUDIO OUT button, and
press this button.

SEARCH VARIABLE

3 Search dial
2 VARIABLE button
1 SEARCH button

1 SEARCH button
To use the search dial for playback in shuttle or jog
mode, press this button, turning it on. Pressing the dial
toggles between shuttle and jog modes. In shuttle
mode, the SHUTTLE indicator in the display section
lights, and in jog mode, the JOG indicator in the
display section lights.
2 VARIABLE button
To use the search dial for playback in variable speed
mode, press this button, turning it on. Pressing the dial
toggles between variable speed mode and jog mode.
3 Search dial
Turn this to carry out playback in the modes shown in
the following table. Turning the dial clockwise lights
the · indicator in the display section and plays back
in the forward direction. Turning the dial
counterclockwise lights the ª indicator in the display
section and plays back in the reverse direction. When
the tape is stopped, the π indicator in the display
section lights.
Pressing this dial toggles between shuttle mode and
jog mode (or between variable mode and jog mode).
When playing back in shuttle or variable mode, the
SHUTTLE indicator in the display section lights, and
when playing back in jog mode, the JOG indicator
lights.
You can carry out noiseless playback in the range of ±
1 times normal speed.

Chapter 1 Overview

DSR-2000/2000P

Location and Function of Parts

Playback modes using the search dial
Operations and functions

Shuttle

Press the SHUTTLE button or the search dial
so that the SHUTTLE indicator in the display
section lights, then turn the search dial.
Playback is carried out at a speed determined
by the position of the search dial. The
maximum shuttle mode playback speed can be
changed using extended menu item 102.
Press the SHUTTLE button or the search dial
so that the JOG indicator in the display section
lights, then turn the search dial. Playback is
carried out at a speed determined by the speed
of rotation of the search dial. The playback
speed range is ±1 times normal speed. The
search dial has no detents.

Jog

Variable
speed

Press the VARIABLE button, turning it on, then
turn the search dial. You can control the
playback speed finely (61 steps) in the range of
–1 to +2 times normal speed.

Subsidiary Control Panel

1 CHARACTER switch
2 CONTROL PANEL switch
3 REC INHIBIT switch
4 KEY INHIBIT switch
5 PROCESS CONTROL switch

CHARACTER
OFF

CONTROL PANEL
EXT

INT

REC INHIBIT

KEY INHIBIT

OFF

Noiseless playback is possible in the range of
±1 times normal speed.
Capstan
override

Hold down the PLAY button and turn the
search dial to adjust the playback speed in the
range of ±15%. Use this for phase adjustment
between this unit and an external device
connected to this unit.

Changing the setting of extended menu item 101 enables you
to select shuttle or jog mode just by turning the search dial
without using the SEARCH or VARIABLE button.

PROCESS
CONTROL

PRESET

MANUAL

OFF

PRESET

MANUAL

REMOTE LOCAL
EXT

INT
REC
RUN

REGEN

FREE
RUN

NDF

PRESET

OFF

VITC

TC SELECT

VIDEO

CHROMA

SET UP

TC GENERATOR

!º TC SELECT switch !¡ VIDEO knob and PRESET/MANUAL switch

The search dial has detents at the still position
and at the normal speed position.
The variable mode playback speed range can
be changed using extended menu item 119.

Chapter 1 Overview

Playback
mode

9 VITC switch
8 DF/NDF switch (DSR-2000 only)
7 FREE RUN/REC RUN switch
6 INT/EXT−PRESET/REGEN switch

!™ SET UP (DSR-2000)/BLACK LEVEL (DSR-2000P)
knob and PRESET/MANUAL switch

!¢ Y/C DELAY knob and PRESET/MANUAL switch

!£ CHROMA knob and PRESET/MANUAL switch

PRESET

!∞ CHROMA PHASE (HUE) (DSR-2000)/
CHROMA PHASE (DSR-2000P) knob and
PRESET/MANUAL switch
PRESET

MANUAL

PRESET

MANUAL

PRESET

MANUAL

!§ SYNC knob

PRESET

MANUAL

!¶ SC knob
VIDEO

CHROMA

1 CHARACTER switch
Select whether or not to superimpose text information
such as time code, menu settings, and alarm messages
on the video signal output from the SDI OUTPUT 3
(SUPER) connector and VIDEO OUT 3 (SUPER)
connector.
ON: Superimposed text
OFF: No superimposed text
The factory default setting is ON.

Chapter 1 Overview

Y/C DELAY CHROMA PHASE SYNC SC
(HUE)
SYSTEM PHASE

2 CONTROL PANEL switch
Select the state of the control panel when this unit is
operated.
INT: When operating this unit by its own control
panel.
EXT: When operating this unit remotely by the
optional DSBK-200 Control Panel connected to
the CONTROL PANEL connector.
The factory default setting is INT.

Chapter 1 Overview

1-13

1-1. DSR-2000

SET UP

1-1. DSR-2000

1-14
Location and Function of Parts

4 KEY INHIBIT switch
When this switch is set to ON, the KEY INHIBIT
indicator in the display section lights, and the buttons
in the upper control panel and lower control panel
specified by the setting of extended menu item 118 are
disabled.
5 PROCESS CONTROL switch
This selects the method of control of the internal
digital video processor.
REMOTE: Select this position to use an optional
UVR-60/60P or BVR-50/50P Remote Control
Unit for remote control of the internal digital
video processor.
MENU: Select this position to use the setup menu to
change the settings for the internal digital video
processor.
LOCAL: Select this position to use the subsidiary
control panel to change the settings for the internal
digital video processor.
6 INT/EXT–PRESET/REGEN (internal/external−
preset/regenerated) switch
This switch is used to make selections relating to the
time code and the internal time code generator.
(In this Operating Instructions, this switch may also be
called simply as the INT/EXT switch or PRESET/
REGEN switch depending on the contents of the
description in which the switch is referred to.)

Setting
INT

Selection of internal/external time code
Time code used
The time code produced by the internal time
code generator
By setting the switch to INT–REGEN or INT–
PRESET, you can select “PRESET” or “REGEN”
for the internal time code generator (see the
next table).

EXT

Selection relating to the internal time code generator
Setting Operation of the internal time code generator
PRESET The initial value of the time code produced by
the internal time code generator can be preset
by a control panel operation or by remote control
from a device connected to the REMOTE-IN or
REMOTE-OUT connector.
REGEN

The internal time code reader is synchronized to
the playback time code read by the internal time
code reader.

7 FREE RUN/REC RUN switch
This switch selects the time code run mode of the
internal time code generator.
FREE RUN: Regardless of the operating mode of
this unit, the time code value advances
continuously while the power is on.
REC RUN: The time code value advances only
during recording. When this mode is selected, set
the INT/EXT−PRESET/REGEN switch to INT−
PRESET.
8 DF/NDF (drop-frame/non-drop-frame) switch
(for the DSR-2000 only)
This switch selects the mode of advancing the time
code generator and time counter.
DF: Drop-frame mode
NDF: Non-drop-frame mode
Note

When the PRESET/REGEN switch is set to REGEN,
since the time code generator is synchronized to the
playback time code, this switch has no effect.
9 VITC switch
To record the time code produced by the internal time
code generator as a VITC, set this switch to ON.
When this switch is set to OFF, internally generated
time code is not recorded as VITC, but VITC present
in the input video signal is recorded unchanged.

!¡ VIDEO knob and PRESET/MANUAL switch
The switch makes the selection described below.
When it is set to MANUAL, you can use the knob to
adjust the video signal output level.
PRESET: Regardless of the position of the knob, the
video signal output level is set to the reference
value.
MANUAL: You can adjust the video signal output
level in the range ±3 dB.
You can change the adjustment range using
extended menu item 714.
!™ SET UP (DSR-2000)/BLACK LEVEL (DSR2000P) knob and PRESET/MANUAL switch
The switch makes the selection described below.
When it is set to MANUAL, you can use the knob to
adjust the (black) setup level (DSR-2000) or black
level (DSR-2000P).
PRESET: Regardless of the position of the knob, the
setup level (DSR-2000) or black level (DSR2000P) is set to the reference value.
MANUAL: You can adjust the setup level (DSR2000) in the range ±30 IRE1), or the black level
(DSR-2000P) in the range ±210 mV.
!£ CHROMA (chrominance) knob and PRESET/
MANUAL switch
The switch makes the selection described below.
When it is set to MANUAL, you can use the knob to
adjust the chrominance signal output level.
PRESET: Regardless of the position of the knob, the
chrominance signal output level is set to the
reference value.
MANUAL: You can adjust the chrominance signal
output level in the range ±3 dB.
You can change the adjustment range using
extended menu item 714.

!º TC (time code) SELECT switch
This switch selects the time code, TC or VITC, shown
in the time counter display.

!¢ Y/C DELAY knob and PRESET/MANUAL
switch
The switch makes the selection described below.
When it is set to MANUAL, you can use the knob to
adjust the Y/C delay.
PRESET: Regardless of the position of the knob, the
Y/C delay is set to the reference value.
MANUAL: You can adjust the Y/C delay in the
range ±100 ns.
!∞ CHROMA PHASE (HUE) (DSR-2000)/
CHROMA PHASE (DSR-2000P) knob and
PRESET/MANUAL switch
The switch makes the selection described below.
When it is set to MANUAL, you can use the knob to
adjust the hue/chrominance phase (the phase
difference from a burst signal).
PRESET: Regardless of the position of the knob, the
hue/chrominance phase is set to the reference
value.
MANUAL: You can adjust the hue/chrominance
phase in the range ±30°.
!§ SYNC knob
This adjusts the output signal sync phase with respect
to the input reference signal to this unit in the range ±3
µs.
Use this adjustment when the output phase of this unit
is not accurately aligned with the reference signal
phase, or when carrying out special effects editing with
this unit and other VCRs connected to a switcher or
other equipment.
!¶ SC (subcarrier) knob
This adjusts the output signal subcarrier phase with
respect to the input reference signal to this unit in the
range ±180°.
For editing with composite signals, use this adjustment
when the output phase of this unit with respect to the
phase of the reference signal is not accurately aligned
with the subcarrier phase.

The external time code selected as follows.
• When the TC SELECT switch is set to TC
The external time code input to the TIME
CODE IN connector
• When the TC SELECT switch is set to VITC
The VITC time code included in the input
video signal

DSR-2000/2000P

In this case, for the internal time code generator,
“REGEN” is always selected (see the next
table).

Chapter 1 Overview

.........................................................................................................................................................................................
1) IRE: A unit for representing a video level laid down by
the IRE (Institute of Radio Engineers). The IRE is now
the IEEE (Institute of Electrical and Electronic
Engineers).
Chapter 1 Overview

Chapter 1 Overview

3 REC (record) INHIBIT switch
When this switch is set to ON, the REC INHIBIT
indicator in the display section lights, and recording on
tape is no longer possible. (See the description of
extended menu item 107.)

DSR-2000/2000P

Location and Function of Parts

1 Analog video input/output section

Connector Panel

Chapter 1 Overview

REF.VIDEO

2 Digital input/output section (see page 30)

ANALOG VIDEO I/O

DIGITAL AUDIO I/O(AES/EBU)
INPUT

REF.VIDEO

VIDEO IN

CH-1/2

OUTPUT

VIDEO IN
IN

1 REF. VIDEO IN connectors
and 75Ω termination switch

i.LINK

SDTI(QSDI)

Chapter 1 Overview

ANALOG VIDEO I/O

1 Analog video input/output section (see page 29)

75Ω
ON

OFF

7 VIDEO IN connectors and 75Ω termination
switch
8 COMPONENT VIDEO Y/R−Y/B−Y IN
connectors

CH-3/4

75Ω
ON

SDI INPUT
CH-1/2

OFF

OUT

SDI OUTPUT
1

CH-3/4

(SUPER)
COMPONENT VIDEO

OUT

OFF

VIDEO CONTROL

LEVEL
LOW
HIGH

OUT

~AC IN

-6dBm

+4dBm -6dBm

CH-1

CH-2

+4dBm -6dBm

CH-3

+4dBm -6dBm

+4dBm

CH-4

3 TIME CODE IN connector

OUT

R-Y

CONTROL PANEL
3

(SUPER)

B-Y

REMOTE-IN

OUT

TIME CODE

ON-600Ω OFF
ON-600Ω OFF
ON-600Ω OFF
ON-600Ω
0dBm
0dBm
0dBm
0dBm

TIME CODE
IN

OUT

2 REF. VIDEO OUT connector

LEVEL
LOW
HIGH

OUT

LEVEL
LOW
HIGH

AUDIO IN

VIDEO OUT

OFF

VIDEO OUT

COMPONENT VIDEO

4 TIME CODE OUT connector

AUDIO OUT

CH-1

CH-2

CH-3

9 COMPONENT VIDEO Y/R−Y/
B−Y OUT connectors

(SUPER)

B-Y

CH-4

S VIDEO

REMOTE-OUT

OUT

MONITOR AUDIO

S VIDEO
IN

OUT

5 S VIDEO IN connector

1 AC IN
connector

3 External device connectors
(see page 31)
2 Ground terminal

4 Analog audio input/output section (see page 31)

This figure shows the connector panel fitted with the optional DSBK-190 i.LINK/DV Input/Output Board.

1 AC IN connector
Use the optional power cord to connect this to an AC
outlet.
2 Ground terminal
Connect this to ground.

6 S VIDEO OUT connector

1 REF. (reference) VIDEO IN connectors (BNC
type) and 75Ω termination switch
Input a reference video signal to one of these
connectors. The two connectors can be used for a loopthrough connection. When making a loop-through
connection, set the termination switch to OFF, and
when not, set the switch to ON.
2 REF. (reference) VIDEO OUT connector (BNC
type)
This connector outputs a reference video signal, except
when i.LINK is selected in the input selection section
(see page 14).
3 TIME CODE IN connector (BNC type)
Input SMPTE time code (DSR-2000) or EBU time
code (DSR-2000P) externally generated to this
connector.

Chapter 1 Overview

4 TIME CODE OUT connector (BNC type)
This connector outputs a time code according to the
operating state of the unit, as follows:
During playback: the playback time code
During recording: the time code generated by the
internal time code generator or the time code input
to the TIME CODE IN connector.

For more information about the time code output during
recording, see extended setup menu item 611.

5 S VIDEO IN connector (4-pin)
Input an S-video signal with separated Y (luminance)
and C (chroma: 3.58 MHz for DSR-2000 or 4.43 MHz
for DSR-2000P) components to this connector.
6 S VIDEO OUT connector (4-pin)
This connector outputs an S-video signal with
separated Y (luminance) and C (chroma: 3.58 MHz for
DSR-2000 or 4.43 MHz for DSR-2000P) components.
7 VIDEO IN connectors (BNC type) and 75Ω
termination switch
Input an analog composite video signal to one of these
connectors. The two connectors can be used for a loopthrough connection. When making a loop-through
connection, set the 75Ω termination switch to OFF and
when not, set the switch to ON.

Chapter 1 Overview

1-15

1-1. DSR-2000

!º VIDEO OUT 1, 2, and 3 (SUPER) connectors

1-1. DSR-2000

1-16
Location and Function of Parts

Chapter 1 Overview

9 COMPONENT VIDEO Y/R–Y/B–Y OUT
connectors (BNC type)
These connectors output analog component video
signals (Y/R−Y/B−Y).

5 DIGITAL AUDIO (AES/EBU) OUT connectors
(BNC type)
These connectors output digital audio signals in AES/
EBU format.
The left-hand connector (CH-1/2) is for audio channels
1 and 2, and the right-hand connector (CH-3/4) is for
audio channels 3 and 4.
Digital audio signals are always output from this unit
at a sampling frequency of 48 kHz.
6 SDI (Serial Digital Interface) INPUT connectors
(BNC type)
Input digital video and audio signals in SDI (D1)
format to the left-hand connector. The right-hand
connector is for an active-through connection.

2 Digital input/output section

2 SDTI(QSDI) INPUT connector
3 SDTI(QSDI) OUTPUT connector
4 i.LINK connector (optional DSBK-190
i.LINK/DV Input/Output Board)

1 DIGITAL AUDIO (AES/EBU) IN connectors

DIGITAL AUDIO I/O(AES/EBU)
IN

CH-3/4

CH-1/2

OUT

CH-3/4

i.LINK

SDTI(QSDI)
INPUT

CH-1/2

OUTPUT

SDI INPUT

SDI OUTPUT
1

7 SDI (Serial Digital Interface) OUTPUT 1, 2 and
3 (SUPER) connectors (BNC type)
These connectors output digital video and audio
signals in SDI (D1) format.
When the CHARACTER switch on the subsidiary
control panel is set to ON, connector 3 (SUPER)
outputs a signal with superimposed text information.
Digital audio signals are always output from this unit
at a sampling frequency of 48 kHz.

2 CONTROL PANEL connector (D-sub 15-pin)
When using the optional DSBK-200 Control Panel to
remotely control this unit, connect the DSBK-200 to
this connector.
3 REMOTE-IN connector (D-sub 9-pin)
When controlling this unit from an editing controller
such as the ES-7, PVE-500, BVE-600/800/910, or
RM-450/450CE, connect the unit to the editing
controller via this connector using the supplied 9-pin
remote control cable.
When controlling another VCR from this unit, connect
the VCR to this connector.
4 REMOTE-OUT connector (D-sub 9-pin)
This connector provides the loop-through output for
remote control signals from the REMOTE-IN
connector.

4 Analog audio input/output section

1 AUDIO IN −6dBm/0dBm/+4dBm switches
2 AUDIO IN LEVEL/600Ω switches

(SUPER)

5 DIGITAL AUDIO
(AES/EBU) OUT connectors

6 SDI INPUT connectors

7 SDI OUTPUT 1, 2, and 3 (SUPER)
connectors

3 External device connectors

LEVEL
LOW
HIGH

AUDIO IN

OFF
-6dBm

CH-1

LEVEL
LOW
HIGH

ON-600Ω OFF
ON-600Ω OFF
ON-600Ω OFF
ON-600Ω
0dBm
0dBm
0dBm
0dBm
+4dBm -6dBm

+4dBm -6dBm

CH-2

CH-3

CH-4

CH-2

CH-3

CH-4

+4dBm

VIDEO CONTROL

1 DIGITAL AUDIO (AES/EBU) IN connectors
(BNC type)
Input digital audio signals in AES/EBU format to these
connectors.
The left-hand connector (CH-1/2) is for audio channels
1 and 2, and the right-hand connector (CH-3/4) is for
audio channels 3 and 4.

If you monitor the output signal from this connector on
another device in E-E mode while making a search at
speeds in the range +1 to +1/30 or –1/30 to –1 times
normal speed, the signal may sound differently than it
does on this unit.

2 SDTI (QSDI) (Serial Data Transport Interface
(QSDI)) INPUT connector (BNC type)
Input digital video and audio signals in SDTI (QSDI)
format to this connector.

4 i.LINK connector (6-pin IEEE-1394)(optional
DSBK-190 i.LINK/DV Input/Output Board)
This connector is available when the optional DSBK190 i.LINK/DV Input/Output Board is fitted.
This connector inputs and outputs digital video and
audio signals in DV format.

3 SDTI (QSDI) (Serial Data Transport Interface
(QSDI)) OUTPUT connector (BNC type)
This connector outputs digital video and audio signals
in SDTI (QSDI) format.

DSR-2000/2000P

Chapter 1 Overview

1 VIDEO CONTROL connector

Note

AUDIO OUT

CH-1

CONTROL PANEL

2 CONTROL PANEL connector

MONITOR AUDIO

REMOTE-IN

3 REMOTE-IN connector
REMOTE-OUT

4 REMOTE-OUT connector

5 AUDIO OUT CH-1 to CH-4
connectors
4 AUDIO IN CH-1 to CH-4 connectors
3 MONITOR AUDIO connector

1 VIDEO CONTROL connector (D-sub 15-pin)
For remote control of the internal digital video
processor, connect an optional remote control unit
such as the UVR-60/60P or BVR-50/50P to this
connector.

1 AUDIO IN −6dBm/0dBm/+4dBm switches
Set these switches according to the audio input levels
to the AUDIO IN CH-1 to CH-4 connectors.

Note

Always power off this unit before connecting the
remote control unit.
Chapter 1 Overview

Chapter 1 Overview

!º VIDEO OUT 1, 2, and 3 (SUPER) connectors
(BNC type)
These connectors output analog composite video
signals.
When the CHARACTER switch on the subsidiary
control panel is set to ON, connector 3 (SUPER)
outputs a signal with superimposed text information.

8 COMPONENT VIDEO Y/R–Y/B–Y IN
connectors (BNC type)
Input analog component video signals (Y/R−Y/B−Y)
to these connectors.

DSR-2000/2000P

Location and Function of Parts

2 AUDIO IN LEVEL/600Ω switches
Set these switches for each channel as shown in the
following table, according to the audio input levels to
the AUDIO IN CH-1 to CH-4 connectors and the
impedance.

Level

Impedance

−60dBs

High impedance LOW-OFF

(microphone input)

(about 20kΩ)

+4dBs/0dBs/−6dBs

High impedance HIGH-OFF

(line audio input)

(about 20kΩ)

(left position)
(middle position)

+4dBm/0dBm/−6dBm 600Ω

HIGH-ON

(line audio input)

(right position)

3 MONITOR AUDIO connector (RCA phono
jack)
This connector outputs audio signals for monitoring.
The audio signals to be output from this connector can
be selected with the MONITOR SELECT buttons on
the lower control panel.
4 AUDIO IN CH-1 (channel 1) to CH-4 connectors
(XLR 3-pin, female)
Use these connectors to connect separate channels of
audio input from a player VCR or other external audio
equipment.
5 AUDIO OUT CH-1 (channel 1) to CH-4
connectors (XLR 3-pin, male)
These connectors output channel-1 to channel-4 audio
signals, respectively.
In 2-channel audio recording mode (selected with
extended menu item 818), it is possible to use the
AUDIO OUT CH-3 and AUDIO OUT CH-4
connectors for monitor audio output for channels 1 and
2, respectively (use extended menu item 820).

This unit can use the DVCAM cassettes listed below.
Model name

Size

PDV-64*/94*/124*/184*/34*

Standard size

PDVM-12*/22*/32*/40*

Mini size

The * in each model name is actually “ME”
(indicating that a cassette memory is contained), or
“N” (indicating that no cassette memory is contained).
The numbers in each model name indicate the
maximum recording/playback time (in minutes) for
each model. For example, the PDV-184ME has a
maximum recording/playback time of 184 minutes.
Cassettes usable for playback only
L- and M-size DVCPRO (25M) cassettes are usable
for playback only.
Notes

• If you insert an incorrect type of cassette, it will be
automatically ejected.
• When operating this unit as a player, you can also use
DV cassettes on the unit. However, it is the best
choice to always use DVCAM cassettes because they
are more reliable than DV cassettes whatever your
purpose may be: playback, editing, or long-period
storage of recordings.
• Cassettes that have been recorded by a DV-format
recorder can be played back on this unit but cannot be
used for recording at editing operation such as the
setting of edit points. When you insert such a
cassette into this unit, the NOT EDITABLE indicator
lights up in the lower control panel display section.

Notes on using cassettes
• Before storing the cassette, rewind the tape to the
beginning and be sure to put the cassette in its storage
case, preferably on end instead of flat on its side. The
storage case of a DVCAM cassette is specially
designed to ensure a long-period storage of the tape.
Storing a cassette in any other condition (not
rewound, out of its case, etc.) may cause the video
and audio contents to become damaged over time.
• If the cassette memory connector (contact point)
becomes dirty, connection problems may occur,
causing a loss of functions. Remove any dust or dirt
from this area before using the cassette.
• If the cassette is dropped on the floor or otherwise
receives a hard impact, the tape may become
slackened and may not record and/or play back
correctly.

Chapter 1 Overview

Settings of the AUDIO IN LEVEL/600Ω switches
Audio input
Switch setting

Usable Cassettes

For information about how to check the tape for slack, see
the next section.

Checking the tape for slack
Using a paper clip or a similar object, turn the reel
gently in the direction shown by the arrow. If the reel
does not move, there is no slack. Insert the cassette
into the cassette compartment, and after about 10
seconds take it out.

DVCAM cassettes
Paper clip, etc.

The following figure illustrates the DVCAM cassette’s
appearance.
REC/SAVE switch
For details of this switch, see “Preventing
accidental erasure” (page 34).

Reel

Standard size
Mini size

Chapter 1 Overview

1-17

1-1. DSR-2000

Cassette memory
This memory is used to store ClipLink log data.
For details of ClipLink log data, see the
appendix “ClipLink Guide” (page 147).

Chapter

Preventing accidental erasure
Set the REC/SAVE switch on the cassette to SAVE to
prevent accidental erasure of recorded contents.

Mini size (Insert the cassette
into the middle of the cassette
compartment.)

Outer guides

Chapter 1 Overview

REC/SAVE switch

Standard size

Set to SAVE
REC
SAVE

Inner guides
Medium size (Align the
cassette with the outer
guides, then slide it in over
the inner guides.)

Displaying Time Data and Unit's Operating Status−
Superimposing Text Information

Inserting a cassette
Tape window facing upward

Ejecting a cassette
Press the EJECT button.

To display superimposed time data and text information about the
operating status of the unit on the monitor, set the CHARACTER switch
on the subsidiary control panel to ON.
When the CHARACTER switch is set to ON, the text information is
superimposed on the output of the VIDEO OUT 3 (SUPER) connector and
also of the SDI OUTPUT 3 (SUPER) connector.
To adjust the displayed text
You can adjust the position, size, and type of superimposed information
using setup menu items 002, 003, 009, and 011.
For details, see pages 108 and 109.

EJECT button

DSR-2000/2000P

Chapter 1 Overview

Chapter 2 Setting/Displaying Time Data and Text Information

Setting/Displaying Time Data and Text Information

Tape window facing upward

Inserting and Ejecting Cassettes

This unit accepts three sizes of cassette: L (standard
size), M (medium size: DVCPRO) and S (mini size).
When inserting a cassette in the unit, make sure its
tape window faces upward as shown in the following
figure.

Setting/Displaying
Time Data and Text
Information

Chapter 2

To enable re-recording
Set the cassette’s REC/SAVE switch to REC.
When this switch is set to SAVE, the unit cannot
record on the tape.

1-1. DSR-2000

1-18
Location and Function of Parts

DSR-2000/2000P

Displaying Time Data and Unit's Operating Status−Superimposing Text
Information
2 Time code reader drop-frame mark (for DSR-2000 only)

Information displayed
The figure below shows the time data and operation status that can be
superimposed.

Time data
2 Timecode reader dropframe marka)
3 Timecode generator
drop-frame marka)

Drop frame mode (factory default setting)

Non-drop frame mode

4 VITC field
“ ” (blank): Fields 1 and 3
“*”: Fields 2 and 4

Chapter 2

2 3 : 5 9 . 4 0 . 1 8 *

S H U T T L E

S T I L L

6 Operating mode
5 Recorder/player selection
a) This character can appear on the DSR-2000 only. The character to
appear in these two columns is always a colon (:) on the DSR-2000P.

Note

The example above shows the factory default configuration.
You can use setup menu item 005 to display a different type of time data in
the second line as well.

5 Recorder/player selection
The indication changes depending on the status of the RECORDER/
PLAYER buttons.
No display: Neither of the RECORDER and PLAYER buttons is lit.
P: The PLAYER button is lit.
R: The RECORDER button is lit.
6 Operation mode
The field is divided into three blocks, A, B and C.
• Block A displays the operation mode.
• Block B displays the servo lock status or tape speed.
• Block C displays a p mark to indicate an edit section during automatic
editing.

Setting/Displaying Time Data and Text Information

Chapter 2 Setting/Displaying Time Data and Text Information

4 VITC field

T C R

Drop frame mode (factory default setting)
Non-drop frame mode

3 Time code generator drop-frame mark
(for DSR-2000 only)

1 Time data type

.
:

For details, see page 108.

1 Time data type
Display

Meaning

CNT

Count value of the time counter (COUNTER)

TCR

Timecode reader timecode data

UBR

Timecode reader user bits data

TCR.

VITC reader time code data

UBR.

VITC reader user bits data

TCG

Timecode generator timecode data

UBG

Timecode generator user bits data

IN point time data

OUT

OUT point time data

Audio IN point time data

Audio OUT point time data

DUR
a)

The duration between any two of the four edit points (IN, OUT,
AUDIO IN, AUDIO OUT)
Time code data from time code reader. The asterisk indicates an
interpolation by the time code reader to make up for the time code
data not correctly read from the tape.

U*Ra)

User bit data from the time code reader. The asterisk indicates that
last data is retained by the time code reader, as the new data has
not been read correctly from the tape.

a) “*” appears when data has not been correctly read from tape.

Chapter 2

Setting/Displaying Time Data and Text Information

Chapter 2 Setting/Displaying Time Data and Text Information

1-19

1-1. DSR-2000

T*R

Display
Block A

Operation mode

Setting Time Code and User Bits
Setting an initial time code value

Block B

CASSETTE OUT

Cassette is not loaded

TAPE UNTHREAD

Tape has not been threaded

STANDBY OFF

Standby off mode

STOP

Stop mode

F.FWD

Fast forward mode

REW

Rewind mode

PREROLL

Preroll mode

PLAY

Set the buttons and switches as shown below.

REMOTE button

Playback mode (servo unlocked)
LOCK

PLAY

Deviation from normal Capstan override mode
speed (%)

Chapter 2

Playback mode (servo locked)

REC

CHARACTER switch

Record mode (servo unlocked)
LOCK

DF/NDF switch

Record mode (servo locked)

EDIT

Edit mode (servo unlocked)

EDIT

LOCK

JOG

STILL

A still picture in jog mode

JOG

FWD

Jog mode in forward direction

Edit mode (servo locked)

JOG

REV

Jog mode in reverse direction

SHUTTLE

(Speed)

Shuttle mode

VAR

(Speed)

FREE RUN/REC RUN switch

INT/EXT−PRESET/REGEN switch

Variable mode
Button/switch settings

AUTO EDIT

Automatic editing mode

PREVIEW

Preview mode

Buttons/switches

Settings

REMOTE button

Off

CHARACTER switch

INT/EXT−PRESET/REGEN switch

INT−PRESET

REVIEW
DMC

(Speed)

Review mode
DMC playback speed

D-PREV

(Speed)a)

DMC editing preview mode

D-EDIT
DMC-SPD

Setting/Displaying Time Data and Text Information

Chapter 2 Setting/Displaying Time Data and Text Information

PLAY

REC

1-1. DSR-2000

1-20

Displaying Time Data and Unit's Operating Status−Superimposing Text
Information

(Speed)
(Speed)

DMC editing mode
DMC initial speed setting

FREE RUN/REC RUN switch

As required

DF/NDF switch

As required

a) Initial speed settings or stored speed settings

To set an initial time code value, use the following procedure.

72 1

RESET button

Display section

(3),4
5
FREE RUN/REC RUN switch

DSR-2000/2000P

Chapter 2

Setting/Displaying Time Data and Text Information

Chapter 2 Setting/Displaying Time Data and Text Information

DSR-2000/2000P

Setting Time Code and User Bits

Press the COUNTER SEL button and select TC.

To set user bits

Time data type indicator TC lights in the display section of the lower
control panel.

You can record up to 8 hexadecimal digits of information (date, time,
event number, etc.) in the time code track.

Press the HOLD button.

Proceed as follows.

The first digit of the time counter display
(hours:minutes:seconds:frames) in the display section begins to flash.

Confirm the JOG indicator in the display section is lit.
If not lit, press the search dial to select jog mode.

Select the digit to set by rotating the search dial.

The flashing digit changes to the digit on the right when you rotate the
search dial clockwise, and to the digit on the left when you rotate it
counterclockwise.

Watching the time data type indicator in the display section, press the
COUNTER SEL button and select U-BIT.

Set the value for the flashing digit by rotating the search dial while
pressing the SEARCH button.

6
7

Carry out steps 2 to 7 of the section “Setting an initial time code
value” (page 39).

Repeat steps 4 and 5 until you finish setting all digits.
Settings are made in hexadecimal (0, 1, 2,... 8, 9, A, B,... E, F).
Press the SET button.

Setting/Displaying Time Data and Text Information

Display section

Chapter 2

Chapter 2 Setting/Displaying Time Data and Text Information

To set all digits to 0
Press the RESET button.

If the FREE RUN/REC RUN switch is set to FREE RUN, the time
code starts to advance immediately.

To set time code to the current time

Chapter 2

Set the FREE RUN/REC RUN switch and DF/NDF switch (for DSR2000 only) on the subsidiary control panel to FREE RUN and DF,
respectively.

Carry out steps 1 to 6 of the previous section “Setting an initial time
code value” to set the time code to a time slightly ahead of the current
time.

Press the SET button at the instant when the current time matches the
displayed time code.

Setting/Displaying Time Data and Text Information

Chapter 2 Setting/Displaying Time Data and Text Information

1-21

1-1. DSR-2000

1-22
Setting Time Code and User Bits

Synchronizing the Internal Time Code Generator With an External
Signal—External Lock

Proceed as follows.

1
1
TIME CODE

This starts the internal time code generator running in synchronization
with the external time code generator.
Once the internal time code generator is synchronized with the external
time code generator, even if the external time code generator
connection is removed, the internal time code generator continues to
run.
Note

When the input mode is V:SDTI, SDTI or i.LINK (the V:SDTI, SDTI or
i.LINK indicator is lit in the input selection/audio mode display section),
then setting the INT/EXT−PRESET/REGEN switch to EXT−REGEN
automatically synchronizes the internal time code generator to the time
code transferred through the SDTI(QSDI) INPUT connector or i.LINK
connector (when fitted with the optional DSBK-190).
Note that when the INT/EXT−PRESET/REGEN switch is set to EXT−
REGEN, the advance mode and frame count mode (DSR-2000 only) are
automatically set as follows.
Advance mode: free running
Frame count mode (DSR-2000 only): the same as the external time
code signal (drop frame or non-drop frame)

To check the synchronization to the external signal

OUT

Press the STOP button to stop this unit, then press the REC button.
Watch the time counter display, and check that the values displayed
coincide with the external time code values.

DSR-2000/2000P

Chapter 2

• When synchronizing to an external time code
Connect the time code output of the external time code generator or
external VCR to the TIME CODE IN connector.
• When synchronizing to the time code (VITC) in an input video
signal
In the input selection section, select an input video signal containing
VITC.

Setting/Displaying Time Data and Text Information

Chapter 2 Setting/Displaying Time Data and Text Information

Setting/Displaying Time Data and Text Information

To synchronize to an external time code signal

Set switches on the subsidiary control panel as follows.
TC SELECT switch: TC or VITC according as you are
synchronizing to TC or VITC
INT/EXT–PRESET/REGEN switch: EXT–REGEN (left position)
VITC switch: ON (when recording VITC)

Chapter 2

Chapter 2 Setting/Displaying Time Data and Text Information

You can synchronize the internal time code generator to an external time
code signal (TC) input to this unit. Use this method to synchronize the
time code generators of a number of VCRs, or to carry out recording
maintaining the synchronization between the source video and time code.
In this case, the settings of the FREE RUN/REC RUN switch and DF/NDF
switch on the subsidiary control panel are ignored.
You can synchronize the internal time code generator to one of the
following external time codes.
• The time code (TC) output of an external time code generator or external
VCR connected to the TIME CODE IN connector
• The time code (VITC) present in a video signal input to the unit
• The time code (TC) input to the SDTI(QSDI) INPUT connector or
i.LINK connector (when fitted with the optional DSBK-190) of the unit

DSR-2000/2000P

Chapter

Recording and
Playback

Chapter 3

Recording

Recording and Playback

This section describes video and audio recording on the unit.

Preparations for Recording
Button/switch settings
Before beginning recording, make any necessary button/switch settings.
For details of the settings of each of the buttons/switches, see the pages indicated
in parenthesis.
MONITOR SELECT buttons (page 17):
select the audio channels to be monitored.

Input selection section (page 14): select the input
video and audio signals.

REMOTE button (page 15): unlit

POWER switch: 1 side
REC controls (page 16):
adjust the audio recording levels.

COUNTER SEL button (page
18: select the data to be
displayed (counter’s count, time
code value, or user bit value)
REC INHIBIT switch (page 26): OFF

INT/EXT–PRESET/REGEN switch (page 26):
select the time code to be recorded.

PB/EE button (page 18): lit

TC SELECT switch (page 26): TC or VITC (when displaying time code)

Chapter 3

Recording and Playback

1-23

1-1. DSR-2000

VITC switch (page 26): ON (when recording VITC)

1-1. DSR-2000

1-24
Recording

To change the number of audio channels to be recorded
Change the setting of extended menu item 818 between 2-channel (2CH)
mode and 4-channel (4CH) mode.

Adjusting the audio recording levels
When carrying out audio recording at a reference level
Leave the REC controls pressed in. The audio signals will be recorded at a
preset reference level.
Manually adjusting the recording levels
For each channel, pull out the REC control in the upper control panel, and
adjust so that the audio level indication is 0 dB for an average volume.
Carry out the adjustment in E-E mode.

Press the METER FULL/FINE button (see page 16).

To set an initial value then record the time code
Use the procedure described in the section “Setting an Initial Time Code
Value” (page 39), then carry out the recording operation (see page 48).
Setting the time code value to the current time
See page 40.

Setting a user bit value
See page 41.

To synchronize the internal time code generator to an external
signal
See page 42.

Setting the reference level
The analog input reference level is determined by the settings of the
AUDIO IN LEVEL/600 Ω switch (see page 32) and extended menu item
811. When, for example, the AUDIO IN LEVEL/600 Ω switch is set to
+4 dBm (HIGH-ON) and extended menu item 811 to –20 dB, the reference
level is set to –20 dB, causing +4 dBm analog input to be converted into a
–20 dBFS digital signal.

DSR-2000/2000P

Chapter 3

Recording and Playback

Chapter 3 Recording and Playback

Recording and Playback

To change the display range of the audio level meters

There are the following two ways of recording time code:
• Setting an initial value, then recording the output of the internal time code
generator
• Recording the output of the internal time code generator synchronized to
an external time code generator

Chapter 3

For details of selecting the E-E mode, see the description of the REC button in the
tape transport control section (page 22) and the PB/EE button in the monitor/
menu/display setting section (page 17).

Recording Time Code and User Bit Values

DSR-2000/2000P

Playback

Recording

This section describes playback of video and audio.

Recording Operation
To record, use the following procedure.

Preparations for Playback
Button/switch settings

Before beginning playback, make any necessary button/switch settings.
For details of the settings of each of the buttons/switches, see the pages indicated
in parenthesis.
MONITOR SELECT buttons (page 17): select the audio channels to be monitored.

2 3
Insert a cassette.
PB controls (page 17):
adjust the audio
playback levels.

COUNTER SEL button (page 18):
select the data to be displayed
(see the section “Displayed time
data” on this page).

Hold down the REC button, and press the PLAY button.
Recording starts, the servo locks, and the SERVO indicator in the
display section lights.

PB button (page 18): lit

Recording and Playback

For details, see the section “Inserting a cassette” (page 34).

Chapter 3

REMOTE button (page 15): unlit

POWER switch: 1 side

To stop recording, press the STOP button.
TC SELECT switch (page 26): TC or VITC (when displaying time
code)(see the section “Displayed time data” on this page)

If you record to the end of the tape
The tape is automatically rewound, and stops.
You can change the setting of extended menu item 125 so that the tape just
stops without being automatically rewound when it is recorded to the end.

Time data selection
Displayed time data
Use the COUNTER SEL button to select one of counter’s count
(COUNTER), time code (TC), and user bit values (U-BIT). When you
select time code, the data displayed is determined by the setting (TC/
VITC) of the TC SELECT switch on the subsidiary control panel as
follows.

Chapter 3

Recording and Playback

Displayed data
TC recorded on tape

VITC

VITC recorded on tape

Chapter 3 Recording and Playback

1-25

1-1. DSR-2000

TC SELECT switch setting
TC

1-1. DSR-2000

1-26
Playback

If you play back to the end of the tape
The tape is automatically rewound, and stops.
You can change the setting of extended menu item 125 so that the tape just
stops without being automatically rewound when it is played back to the
end.

Playback Operation

Playback in jog mode
In jog mode, you can control the speed of playback by the speed of turning
the search dial. The playback speed range is ±1 times normal speed (can be
changed using extended menu item 116).
To carry out playback in jog mode, use the following procedure.

Display section

1,2,3

Recording and Playback

Normal playback
First insert a cassette.

For details of how to insert a cassette, see the section “Inserting and Ejecting
Cassettes” (page 34).
Cassette compartment

Press the SEARCH button or search dial so that the JOG indicator in
the display section is lit.
Pressing the search dial toggles between jog mode and shuttle mode.

Display section

Turn the search dial in the desired direction, at the speed
corresponding to the desired playback speed.
Playback in jog mode starts.

STOP button
PLAY button

To stop playback in jog mode, stop turning the search dial.

To start playback
Press the PLAY button.
Playback starts, the servo locks, and the SERVO indicator in the display
section lights.
To stop playback
Press the STOP button.

DSR-2000/2000P

Chapter 3

Recording and Playback

Chapter 3 Recording and Playback

Chapter 3

This section describes the following types of playback:
• Normal playback
Playback at normal (×1) speed
• Playback in jog mode
Variable speed playback, with the speed determined by the speed of
turning the search dial
• Playback in shuttle mode
Variable speed playback, with the speed determined by the angular
position of the search dial
• Playback in variable mode
Variable speed playback, with the speed finely determined by the angular
position of the search dial
• Playback using the capstan override function
The playback speed is adjusted temporarily according to the angular
position of the search dial, to align the playback phase with that of
another VCR.

DSR-2000/2000P

Playback

Playback in shuttle mode

Playback in variable mode
In shuttle mode, you can control the speed of playback by the angular
position of the search dial. The range of playback speed is ±32 times
normal speed (can be changed using menu item 102).
There are detents on the search dial at the still position and at ±10 times
normal speed.
To carry out playback in shuttle mode, use the following procedure.

In variable mode, you can finely control (61 steps) the speed of playback
in the range of −1 to +2 times normal speed. Noiseless playback is possible
in the range of ±1 times normal speed.
(The variable mode playback speed range can be changed using extended
menu item 119.)
There are detents on the search dial at the still position and at ±1 times
normal speed.
To carry out playback in variable mode, use the following procedure.

Display section

1,2,3

Display section

4 1 2
Press the SEARCH button or search dial so that the SHUTTLE
indicator in the display section is lit.
Pressing the search dial toggles between jog mode and shuttle mode.

Press the VARIABLE button or search dial so that the SHUTTLE
indicator in the display section is lit.

Turn the search dial to the desired angle corresponding to the desired
playback speed.

If the SEARCH button is lit, press the VARIABLE button, turning it
on.

Playback in shuttle mode starts.

Turn the search dial to the desired angle corresponding to the desired
playback speed.

To stop playback in shuttle mode, return the search dial to the center
position, or press the STOP button.

To return to normal-speed playback
Press the PLAY button.
To alternate between normal-speed playback and shuttle mode
playback
Set the search dial to the position corresponding to the desired shuttle
playback speed, then switch between normal-speed playback and shuttle
playback by pressing the PLAY and SEARCH buttons alternately.
For intermittent shuttle mode playback, press the STOP and SEARCH
buttons alternately.

Chapter 3

Recording and Playback

Playback in variable mode starts.

To stop playback in variable mode, return the search dial to the center
position, or press the STOP button.

To return to normal-speed playback
Press the PLAY button.
To alternate between normal-speed playback and variable
mode playback
Set the search dial to the position corresponding to the desired variable
playback speed, then switch between normal-speed playback and variable
playback by pressing the PLAY and VARIABLE buttons alternately.
For intermittent variable mode playback, press the STOP and VARIABLE
buttons alternately.

Chapter 3 Recording and Playback

1-27

1-1. DSR-2000

Recording and Playback

Chapter 3

1,2,3

3 1

1-1. DSR-2000

1-28
Playback

Playback using the capstan override function

Dynamic Motion Control (DMC) Playback

You can use the capstan override function to adjust the playback speed
temporarily. This function is convenient for playback phase
synchronization with another VCR playing back the same program.

Overview
DMC playback allows you to vary the playback speed for a certain section
of a tape, in variable mode (from −1 to +1 times normal speed), and store
the varying speed in memory for later playback at the same varying speed.
For example, during a live broadcast of a sporting event you can set the
start and end points of highlights while recording, and then provide
immediate DMC playback of those highlights.

Display section

During DMC playback the tape moves as shown in the following figure.

1(A)

(A) Hold down the PLAY button, and turn the search dial in the
desired direction to adjust the playback speed.
The range of speed adjustment is ±15% in steps of 1%.
(B) Hold down the PLAY button, and press the TRIM buttons to
adjust the playback speed.
The playback speed can be adjusted to ±8% only.
The SERVO indicator in the display section goes off.

When the adjustment is completed, release the PLAY button.

Press the REVIEW button
again at the on-air cue.

Preroll point

Speed variation start point

Speed variation end point

On-air end point

Press the REVIEW button.
Normal speed
playback

DMC playback

Normal speed playback

Recording and Playback

On-air start point
Waiting for the on-air cue
before starting DMC playback. Stop

Chapter 3

1(B) 1(A),1(B),2

Stop

Starting DMC playback
immediately after preroll

Press the PREVIEW button.
Normal speed
playback

DMC playback

Normal speed playback

The tape transport returns to normal speed, and the SERVO indicator
in the display section lights on again.

DSR-2000/2000P

Chapter 3

Recording and Playback

Chapter 3 Recording and Playback

DSR-2000/2000P

Playback

Storing a varying playback speed in memory

While the MEMORY indicator is flashing, the speed variations are
stored in memory. On passing the speed variation end point, the
MEMORY indicator changes from flashing to continuously lit, and the
variable speed storing ends.

To store the playback speed for DMC playback, use the following
procedure.
MEMORY indicator

3,5,7

To amend the stored speed variation
Press the PREVIEW button.
The interval between the speed variation start and end points is
automatically played back at the stored speed. Operate the search dial as
required, to adjust the playback speed.

8 3 4

Press the DMC EDIT button, turning it on.
Either while playing back the recorded tape, or during recording, press
the ENTRY/SHIFT button and each of the following buttons
simultaneously, to set the start and end points.
• On-air start point: AUDIO IN button
• Speed variation start point: IN button
• Speed variation end point: OUT button
• On-air end point: AUDIO OUT button
Each press turns the corresponding button on.
Press the SEARCH button or search dial so that the SHUTTLE
indicator in the display section is lit.

If you want to use the variable mode to set the varying playback speed,
press the VARIABLE button, turning it on.

Holding down the DMC EDIT button, turn the search dial, to set the
initial speed at the speed variation start point.

Setting the initial speed to normal speed
In step 5, press the PLAY button.

Recording and Playback

Chapter 3

1
2

Press the STOP button to stop the tape.

If the MEMORY indicator lights continuously before the speed
variation end point
This indicates that the memory became full at that point. It is therefore not
possible to record more speed variation. The maximum capacity is a
duration of 120 seconds.

Display section

1,5

Turn the search dial to vary the playback speed.

Executing DMC Playback
There are two methods of starting DMC playback.
• Starting playback at the on-air cue from the on-air start point
• Starting playback immediately after preroll
Notes

• To avoid operating mistakes we recommend that you use the VCR in
standalone mode when carrying out DMC playback.
• When using two VCRs connected for editing, you can only use the
recorder VCR for DMC playback, and only when both the RECORDER
and PLAYER buttons are off.

The speed you set appears in the display section. During this period the
tape does not move.

Press the PREVIEW button.
The tape is prerolled and played back at normal speed from the on-air
start point to the speed variation start point. On passing the speed
variation start point, the MEMORY indicator begins to flash, and
playback begins at the speed set in step 5.

Chapter 3

Recording and Playback

Chapter 3 Recording and Playback

1-29

1-1. DSR-2000

1-30
Playback

You can start DMC playback using either the REVIEW button or
PREVIEW button depending on which of the above two methods you use.

Synchronous Playback
Connecting two DSR-2000/2000P units and synchronizing their tape
transport, you can carry out two-unit synchronous playback with an
accuracy of ±0 frame.
For equipment/signal connections and basic settings, see the section
“Connections for Two-Unit Synchronous Playback” (page 132).

Use the following procedure.
(In the following, the controlling unit is referred to as the recorder (this
unit) and the controlled unit as the player.)
REVIEW button

1 4

PREVIEW button

Chapter 3

To start playback at the on-air cue from the on-air start point
Use the following procedure.
Press the REVIEW button.
The REVIEW button lights, and the tape is cued up to the on-air start
point. After the tape is cued up, the REVIEW button flashes.

Recording and Playback

2,5

3,6

At the moment the on-air cue is given, press the REVIEW button once
more.
The REVIEW button lights, and playback starts at normal speed.
Between the speed variation start and end points, DMC playback is
carried out at the stored speed, and then playback continues at normal
speed and the tape stops at the on-air end point.

Starting playback immediately after preroll
Press the PREVIEW button.
The PREVIEW button lights, and after preroll, DMC playback is carried
out for the section between the speed variation start and end points, then
playback continues at normal speed from the speed variation end point.
Stopping the tape during DMC playback
Press the STOP button.
To exit DMC playback mode
Press the DMC EDIT button and the DELETE button simultaneously.

1
2
3

Press the PLAYER button, turning it on.
Cue up to the player tape position where to start playback.
Hold down the ENTRY/SHIFT button, and press the IN button.
The player IN point is set.

4
5
6

Press the RECORDER button, turning it on.
Cue up to the recorder tape position where to start synchronous
playback.
Hold down the ENTRY/SHIFT button, and press the IN button.
The recorder IN point is set.
(Continued)

DSR-2000/2000P

Chapter 3

Recording and Playback

Chapter 3 Recording and Playback

DSR-2000/2000P

Digitally Dubbing Signals in DVCAM Format
(Optional DSBK-190 Required When Using i.LINK Interface)

Playback

Hold down the ENTRY/SHIFT button, and press the PREVIEW
button.
Both the recorder and player start preroll followed by synchronous
playback by the two units.
When setup menu item 004 is set to ON and 305 set to ACCUR on the
recorder side, the recorder and player tape transports are synchronized
during the preroll allowing two-unit synchronous playback with ±0
frame accuracy to start at the player and recorder IN points.

To end synchronous playback while it is in progress
Press the STOP button.

In addition to straightforward tape dubbing, you can also use this unit to
digitally dub signals in DVCAM format automatically from the beginning
of the tape to the end, through an i.LINK or SDTI(QSDI) interface.
When a tape recorded on a DSR-1/1P Digital Videocassette Recorder or
DSR-300/300P Digital Camcorder is dubbed, the ClipLink log data held in
the cassette memory is also copied.
For information about connections and basic settings, see the section
“Connections for Digitally Dubbing Signals in DVCAM Format” (page 133).
Notes

Recording and Playback

Perform the following procedure.

Chapter 3

• Use a tape which is recorded in the DVCAM format. A tape recorded in
DV format cannot be used as a source tape for an dubbing operation
using the AUTO FUNCTION menu.
• Regardless of the audio channel settings made in the input selection
section of this unit, dubbing is performed with the original audio
recording mode unchanged (two-channel mode (48 kHz) or four-channel
mode (32 kHz)).
• Approximately the last 2 minutes of the tape may not be copied because
of differences in tape lengths. (If an Index Picture is recorded in this
portion, it may also not be copied.)
• A continuous recorded section of approximately 5 seconds is required
before the recording start point. It is recommended to record beforehand
color bars or a similar signal at the start point of the recording tape to be
used on this unit.

7 2,5
4
3
1
1

On the recorder, hold down the ENTRY/SHIFT button and press the
MENU button.
The SYSTEM MENU screen appears on the monitor connected to this
unit.
(Continued)

Chapter 3

Recording and Playback

Chapter 3 Recording and Playback

1-31

1-1. DSR-2000

1-32

Digitally Dubbing Signals in DVCAM Format (Optional DSBK-190 Required
When Using i.LINK Interface)

4
SYSTEM MENU

Using the search dial, select a desired group of items for dubbing, then
press the SET button.
The menu screen changes as follows.
(Example: The screen displayed when A/V/TC/CM is selected.)

SETUP MENU
AUTO FUNCTION
HOURS METER

SDTI DUBBING
(A/V/TC/CM)
INSERT RECORD TAPE IN
THIS VTR AND SOURCE
TAPE IN THE PLAYER VTR.

Using the search dial, select AUTO FUNCTION, then press the SET
button.
ABORT:MENU KEY
AUTO FUNCTION MENU
SDTI DUBBING
i.LINK DUBBING

Insert the source tape in the player and the recording tape in this unit.
A message to make sure dubbing may be started appears.

Recording and Playback

SDTI DUBBING
(A/V/TC/CM)
START SDTI DUBBING?

Using the search dial in jog mode, select either SDTI DUBBING or
i.LINK DUBBING, then press the SET button.
The screen changes as follows, allowing you to select a desired group
of items for dubbing.
(In explaining the subsequent operating procedure, illustrations of
screens shown when performing SDTI dubbing are used. You can
follow the same operating procedure also when performing i.LINK
dubbing.)
AUTO FUNCTION MENU
SDTI DUBBING
A/V
A/V/TC
A/V/TC/CM

START:SET KEY
ABORT:MENU KEY

If the cassette memory capacity is not sufficient
A message urging you to replace the recording tape by a tape with a
larger cassette memory capacity appears.
For more information about this, see the section “If the cassette memory of
the recording tape is not large enough” (page 65).

To cancel the dubbing operation
Press the MENU button.

(Continued)

DSR-2000/2000P

• A/V: Audio and video
• A/V/TC: Audio, video and timecode
• A/V/TC/CM: Audio, video, timecode, and cassette memory
(ClipLink log data)

Chapter 3

Recording and Playback

Chapter 3

Chapter 3 Recording and Playback

DSR-2000/2000P

Digitally Dubbing Signals in DVCAM Format (Optional DSBK-190 Required
When Using i.LINK Interface)

Press the SET button.
The recording tape and source tape are both automatically wound back
to the beginning, and dubbing starts. At the same time, the screen
changes as follows.

If the cassette memory of the recording tape is not large
enough
When you insert the recording tape and source tape in this unit and the
player, respectively, with A/V/TC/CM selected as the items for dubbing,
their cassette memory contents are checked automatically. If, as a result,
the cassette memory capacity of the recording tape is found inadequate, the
following message appears.

SDTI DUBBING
(A/V/TC/CM)
EXECUTING.
TCR 00:00:00:00
UBR 00:00:00:00

SDTI DUBBING
(A/V/TC/CM)
CM MEMORY STORAGE
CAPACITY OF THE RECORD
TAPE IS TOO SMALL.

ABORT:MENU KEY
ABORT:MENU KEY

When dubbing is completed
1 A message “COMPLETED” appears on the monitor.
2 The source tape and recording tape are both automatically rewound
to the beginning, and the cassettes ejected.
3 The unit returns to the state in step 4.

7
8

If you end dubbing while it is in progress
If you end dubbing while it is in progress with A/V/TC/CM selected as the
items for dubbing, the following message appears.

Recording and Playback

For more information about this, see the section “If you end dubbing while it
is in progress” (page 65).

If this message appears, replace the recording tape by a tape with a larger
cassette memory capacity.

Chapter 3

To end the dubbing operation while it is in progress
Press the STOP button.
The dubbing operation stops and a message asking whether to copy the
contents of the cassette memory appears.

SDTI DUBBING
(A/V/TC/CM)
DUBBING IS ABORTED.
EXECUTE CM COPY?

To continue by dubbing another tape, repeat steps 5 and 6.
To end the dubbing operation and exit from the menu, press the
MENU button.

COPY
:SET
KEY
NOT COPY:RESET KEY

To copy the contents of the cassette memory, press the SET button.
If you do not wish to copy the contents of the cassette memory, press the
RESET button. If you press the RESET button, however, the contents of
the cassette memory may not agree with the material recorded on the tape.

Chapter 3

Recording and Playback

Chapter 3 Recording and Playback

1-33

1-1. DSR-2000

1-34

Chapter

Editing

Automatic Editing
This section describes how to carry out automatic editing with this unit and
another VCR connected to the REMOTE-IN or REMOTE-OUT connector.

Overview of Automatic Editing

Note

Before you begin assemble editing for the first time with a new tape, a
video signal, e.g. a black signal, and time code must be recorded on the
tape in advance of the recorder IN point for a length equal to or greater
than the preroll time.

DSR-2000/2000P

Chapter 4 Editing

Editing

Assemble edit mode
In assemble editing, you record video and audio materials in order from
the start of the tape. In addition to video and audio, time code is also
recorded. This edit mode is convenient when you are recording on a new
tape.

Chapter 4

With this unit, you can use the following two edit modes.
• Assemble edit mode
• Insert edit mode
(In this Operating Instructions, these two modes are also referred to simply
as assemble mode and insert mode, respectively.)

DSR-2000/2000P

Automatic Editing

Insert edit mode
In insert editing, you insert video, audio, and time code at desired positions
on an already recorded tape. You can insert all three types of data at the
same time or insert one of the types separately.
Note

Before you use an unrecorded tape in insert editing, a video signal, e.g. a
black signal, and time code must be recorded on all over the tape.

Sequence of editing operations
The following flowchart outlines the sequence of operations in automatic
editing with two DSR-2000/2000P units.
Sequence of Operation
Making necessary settings

See
“Button/Switch Settings for
Editing” (page 70)

You can carry out DMC editing in both edit modes. In insert editing, split
editing is also possible.
To record a video signal and time code on an unrecorded tape
When recording a video signal and time code on an unrecorded tape to use
it as a recording tape in insert editing, you can use a test signal generated
by the internal signal generator of the unit. An example procedure follows.

1
2
3

“Usable Cassettes” (page
33)

Insert an unrecorded cassette in the unit and rewind it.
Using the VIDEO IN button in the input selection section (see page
14), select the video test signal (SG) as the input video signal.
Set switches on the subsidiary control panel (see page 25) as follow.
INT/EXT-PRESET/REGEN switch: INT−PRESET (right position)
FREE RUN/REC RUN switch: REC RUN
DF/NDF switch: Set as required.

Select an edit mode.

“Selecting an Edit Mode”
(page 71)

Determine edit points.

“Setting Edit Points” (page
72)

Carry out recording (see page 48).

Recording time code
For automatic editing, regardless of the settings of the INT/EXT−
PRESET/REGEN switch, time code is recorded continuously from the
previous time code recorded on the tape.

Preview the editing results.

Modify edit points as necessary.

“Checking Editing Results—
Preview” (page 80)

Editing

Set an initial time code value (see page 39)

Chapter 4

4
5

Insert cassettes.
• Insert a cassette for recording the results of
editing in the recorder.
• Insert the cassette on which material to be edited
has been recorded in the player.

“Modifying Edit Points”
(page 76)

Using extended menu item 610, it is also possible to record time code according to
the settings on the control panels.
Execute automatic editing.

Review the editing results as necessary.

Chapter 4

Editing

“Reviewing the editing
results” (page 83)

Chapter 4 Editing

1-35

1-1. DSR-2000

“Executing Automatic
Editing” (page 81)

1-1. DSR-2000

1-36
Automatic Editing

Player settings

Notes on video output to the monitor
In E-E mode, the video output of the unit is delayed by the time for video
circuit processing with respect to the input video signal (8H).
Unlike the playback operations described in Chapter 3, for playback to be
carried out in edit mode with both the player and recorder specified, you
can use extended menu item 701 to delay the V-SYNC phase by 8H.

REMOTE button (page 15): lit
9PIN (when using REMOTEIN/-OUT) or i.LINK (when
using i.LINK) button: lit

POWER switch: I side

PB controls (page 17):
adjust the audio playback
levels.

Button/Switch Settings for Editing

COUNTER SEL button (page
18): select the data to be
displayed (counter value or
time code value)

Before beginning editing, set buttons and switches on the recorder and
player as follows.
PB button (page 18): lit

For details of the settings of each of the buttons/switches, see the pages indicated
in parenthesis.
TC SELECT switch (page 26): TC or VITC, when displaying time code

Recorder settings

(In the subsequent description, except where the player is explicitly
mentioned, operations are all on the recorder.)

MONITOR SELECT buttons (page 17): select the audio channels to be monitored.

Chapter 4

Input selection section (page 14): select the input video and
audio signals.

Selecting an Edit mode

REC controls (page 16):
adjust the audio recording
levels.

Editing

REMOTE button (page 15):
unlit 9PIN (when using
REMOTE-IN/-OUT) or i.LINK
(when using i.LINK) button: lit

POWER switch: I side

Select either assemble mode or insert mode.

COUNTER SEL button (page
18): select the data to be
displayed (counter value or
time code value)
REC INHIBIT switch (page 26): OFF
INSERT buttons

TC SELECT switch (page 26): TC or VITC, when displaying time code

IN button and OUT button
ASSEMBLE button

INT/EXT–PRESET/REGEN switch (page 26): select the time code to be recorded.

Depending on the desired edit mode, press the following button or buttons.
• For assemble editing: ASSEMBLE button
• For insert editing: the desired INSERT buttons (VIDEO, CH-1 to CH-4,
TC)
When you select an edit mode, the IN and OUT buttons begin to flash,
indicating that the edit points require setting.
DSR-2000/2000P

Chapter 4

Editing

Chapter 4 Editing

DSR-2000/2000P

Automatic Editing

Notes

Setting Edit Points

In the following cases, the DELETE button begins to flash and you cannot
carry out automatic editing.
• The OUT point is before the IN point.
• All four of the recorder IN and OUT points and the player IN and OUT
points have been set.
Use the DELETE button to delete a redundant edit point, or set the edit
points correctly.

Of the four edit points (recorder IN and OUT points, and player IN and
OUT points) required, set any three. The last edit point is set
automatically.
In insert mode, you can set the edit points for video and audio separately
(split editing).
For details of setting split edit points, see the section “Setting split edit points”
(page 73).

To set edit points

For details of deleting edit points, see the section “To delete an edit point” (page
77).

Setting split edit points
In split editing, you can set the edit points for audio and video
independently. Set the audio edit points with the AUDIO IN/OUT buttons,
and the video edit points with the IN/OUT buttons.
Note that split editing is only possible when the recorder is set for insert
editing.

2
1

Chapter 4

3
Press the RECORDER button or PLAYER button to select the VCR on
which you will set edit points.

Editing

The button which you have pressed lights.

Turn the search dial in jog or shuttle mode, and position the tape at the
required edit point.
For details of playback in jog or shuttle mode, see the sections “Playback in
jog mode” (page 51) and “Playback in shuttle mode” (page 52).

At the point at which you wish to set the IN point or OUT point, hold
down the ENTRY/SHIFT button and press the IN button or OUT
button as the case may be.

The IN and OUT buttons flash.

Repeat steps 1 to 3 until three of the four edit points (recorder IN and
OUT points, and player IN and OUT points) are set.

Chapter 4

Editing

To find the edit point, rotate the search dial in jog or shuttle mode.
For details of jog/shuttle mode playback, see the sections "Playback in jog
mode" (page 51) and “Playback in shuttle mode” (page 52).

Hold down the ENTRY/SHIFT button and press one of the IN, OUT,
AUDIO IN, and AUDIO OUT buttons, to set the edit point.

(Continued)
Chapter 4 Editing

1-37

1-1. DSR-2000

When the IN points on both the recorder and player are set, the
PREVIEW button and AUTO EDIT button flash, indicating that it is
possible to carry out a preview or editing operation.

Press the RECORDER or PLAYER button to select the VCR for
which edit points are to be set.
The button you have pressed lights.

When the IN point or OUT point is set, the IN button or OUT button
correspondingly lights.

Press the appropriate INSERT button (VIDEO, CH-1 to CH-4, or TC).

1-1. DSR-2000

1-38
Automatic Editing

Repeat steps 2 through 4 to set the required edit points.

When the audio IN point is not set for insert editing of audio
only
As long as the audio OUT point is set, the VCR is ready for preview or
editing. If the audio IN point has not been set, the current tape position is
automatically used as the audio IN point.

As each edit point is set, the corresponding button changes from
flashing to continuously lit.
Note

Using a VCR without a split editing function as the player
If it is not possible to set separate audio and video edit points on the VCR
you are using as the player, by setting the audio IN and OUT points on the
recorder (this unit), then setting three video edit points, split editing is
possible.

During split editing, if you set six or more edit points for the recorder and
player, the DELETE button starts to flash, to indicate that editing cannot
be executed. Delete all excess edit points, using the DELETE button.
For details of deleting edit points, see the section “To delete an edit point” (page
77).

Automatic setting of edit points in split editing
Split editing requires a total of eight edit points: four video edit points
(player IN and OUT and recorder IN and OUT) and four audio edit points
(player audio IN and OUT and recorder audio IN and OUT). However, as
soon as you set five points, the system automatically calculates and sets the
remaining three points. Specifically, once you have set three of the four
video edit points and two audio edit points, the remaining three edit points
are set automatically, regardless of whether these points are for the
recorder or player.

Checking Edit Points
You can check the time value for an edit point and the duration between
two edit points by displaying them in the display section.

To display the time value for an edit point
Use the following procedure.
Display section
Chapter 4

Chapter 4

In the figure below, the edit points shown within boxes are already set. The
other edit points (recorder audio OUT point, and player audio IN and video
OUT points) are set automatically.
Note that, regardless of whether it was set manually or automatically, any
edit point can be deleted or corrected later.

Editing

Audio IN point

IN point

Audio OUT point

OUT point

Recorder

Player
Audio IN point

IN point

Audio OUT point

OUT point

Press the RECORDER button or PLAYER button to select the VCR on
which you wish to check the edit point.
The button you have pressed lights.

You can set audio cut in, crossfade, fade in, and fade out effects using extended
menu item 317.

Hold down the IN, OUT, AUDIO IN, or AUDIO OUT button
according to the edit point you wish to check.
While you hold down the button, the time value of the edit point is
shown in the display section.

DSR-2000/2000P

Chapter 4

Editing

Chapter 4 Editing

DSR-2000/2000P

Automatic Editing

To display the duration between two edit points

To modify an edit point
Use the following procedure.

Press the RECORDER button or PLAYER button to select the VCR on
which you wish to check the duration.

Display section

The button you have pressed lights.

Hold down any two of the four edit point buttons (recorder or player
IN, OUT, audio IN, and audio OUT points).
While you hold down the buttons, the duration between the two edit
points is shown in the display section.

When only one of the two selected edit points is set
The duration between the edit point and the current tape position is
displayed.

2
1

When neither of the two selected edit points is set
The duration between the most recently set corresponding edit points is
displayed.

Press the RECORDER button or PLAYER button to select the VCR on
which you wish to modify the edit point.
The button you have pressed lights.

Modifying Edit Points

While you hold down the button, the time value for the edit point
appears in the display section; pressing the +button increases the value
by one frame, and pressing the –button decreases it by one frame.

Editing

To turn a flashing DELETE button off
The DELETE button goes off when the erroneous edit point is correct.

Chapter 4

Once you set edit points, you can modify or delete them as required.
When edit points have been set incorrectly, for example when an OUT
point is located before an IN point or when the duration of editing
segments on the player and recorder do not match, the DELETE button
flashes to alert you that a preview or edit cannot be carried out. In this
case, either modify the erroneous edit point, or first delete it and then enter
it correctly.

Hold down the IN, OUT, AUDIO IN, or AUDIO OUT button
corresponding to the edit point you wish to modify, and press the
TRIM buttons (+ or –).

To delete an edit point
To delete an edit point, use the following procedure. You can use the same
procedure whether or not the DELETE button is flashing.

1
(Continued)

Chapter 4

Editing

Chapter 4 Editing

1-39

1-1. DSR-2000

1-40
Automatic Editing

Press the RECORDER button or PLAYER button to select the VCR on
which you wish to delete the edit point.

Use the following procedure.

The button you have pressed lights.

To preroll

Hold down the DELETE button and press the IN, OUT, AUDIO IN, or
AUDIO OUT button according to the edit point you wish to delete.
The edit point is deleted, and the DELETE button goes off.

Cuing Up to Edit Points
You can cue up to any edit point, or cue up to a position located a specified
amount of time before the edit start point (preroll).

To cue up to an edit point

1
Use the following procedure.

Press the RECORDER button or PLAYER button to select the VCR on
which you wish to carry out a preroll.
The button you have pressed lights.

Press the PREROLL button.

Press the RECORDER button or PLAYER button to select the VCR on
which you wish to cue up to an edit point.
The button you have pressed lights.

Hold down the IN, OUT, AUDIO IN, or AUDIO OUT button
according to the edit point to which you wish to cue up, and press the
PREROLL button.
The edit point you have selected is cued up.

DSR-2000/2000P

Chapter 4

Editing

Chapter 4 Editing

Editing

To change the preroll time
The factory default setting for the preroll time is 5 seconds, but you can
use basic menu item 001 to change this to any value from 0 to 30 seconds.
If you change the preroll time, make sure that the setting is not longer than
the recording length before the edit IN point.
Note that for automatic editing, the preroll time setting on the recorder
takes precedence.

Chapter 4

The tape is wound back to a position 5 seconds (factory default setting)
before the edit IN point, and stops.

DSR-2000/2000P

Automatic Editing

Monitor output during a preview

Checking Edit Results—Preview

During a preview, you can monitor the following video and audio on a
monitor connected to the recorder.
• From the preroll point to the IN point, you can monitor the playback from
the recorder.
• From the IN point to the OUT point, you can monitor the playback from
the player through the recorder in E-E mode.
• From the OUT point to the postroll point, you can monitor the playback
from the recorder.

When you have set the edit points, the PREVIEW button flashes,
indicating that you can carry out a preview.

The following figure illustrates this.
IN point

Playback (recorder)

PREVIEW button

To carry out a preview, press the PREVIEW button.
The PREVIEW button changes from flashing to continuously lit, and the
preview is carried out.
At the end of the preview, the PREVIEW button flashes again.

OUT point

E-E mode (player)

Playback (recorder)

Executing Automatic Editing
Overview of editing operations
Chapter 4

Chapter 4

To stop the preview
Press the STOP button.
The tape stops at the position where you pressed the button.

The figure below shows how the recorder and player operate during
editing.

Editing

To return the tape to the preroll point
Press the PREROLL button.

Tape transport

To return the tape to the IN point or OUT point
Press the PREROLL button and the IN button or OUT button
simultaneously.

Preroll point

IN point

OUT point

Postroll point

Recorder
Preroll

After the preview, make any necessary adjustments to the edit points, then
repeat the preview.

Postroll

Editing results

Recording overlap
(When editing in
assemble mode)

For details of how to modify or delete edit points, see the section “Modifying Edit
Points” (page 76).

Stop

Player

Time flow

Playback
Stop

Chapter 4

Editing

Chapter 4 Editing

1-41

1-1. DSR-2000

1-42
Automatic Editing

Monitor output during an edit
During execution of an automatic edit, on a monitor connected to the
recorder, you can monitor the same video and audio as during a preview
(see page 81).
However, during preread editing (see page 87), only the playback from the
recorder can be monitored.

Using a single monitor for video and audio on both player and recorder
For efficient editing if only one monitor is available, use the following
method.

1
2
3

Connect the monitor to the recorder.
In the setup menus, set item 008 to “AUTO”.
Press the PLAYER button on the recorder.
This forces the recorder to E-E mode, in which the player video and
audio signals are output to the monitor.

Note

When you have set the edit points, press the flashing AUTO EDIT button.
The AUTO EDIT button changes from flashing to continuously lit, and the
automatic editing operation begins.
At the end of the editing operation, the AUTO EDIT button goes off.

Reviewing the editing results
After carrying out an editing operation, you can carry out a review, to
check the editing results on the monitor.
To carry out a review, after carrying out the edit, and before you set any
new edit points or make other settings, press the REVIEW button.
The REVIEW button lights, and the review is carried out.
At the end of the review the REVIEW button goes off, and the tape returns
to the OUT point.
After automatic editing, to adjust the edit points and reexecute
the edit
Hold down the DELETE button and press the ENTRY/SHIFT button to
recall the edit points. After adjusting the edit points, press the AUTO
EDIT button to carry out the edit again.
For details of how to adjust edit points, see the section “Modifying Edit Points”
(page 76).

ENTRY/SHIFT button

DELETE button
AUTO EDIT button

PREVIEW button

OUT button

STOP button

REVIEW button

DSR-2000/2000P

Chapter 4

Editing

Chapter 4 Editing

Editing

Starting automatic editing

To abandon automatic editing
Press the STOP button.
The automatic editing operation is abandoned. At the same time, the
PREVIEW button and AUTO EDIT button start flashing, and the state
before the editing was started is restored.
In this case, the IN and OUT points already set are preserved so that you
can carry out a preview or automatic editing operation again by pressing
the PREVIEW button or AUTO EDIT button.

Chapter 4

Continuous recording must exist on the recorder tape to be used in issert
editing. It is not possible to carry out editing on a section of the tape with
no signal recorded.

To change the OUT point after starting automatic editing
operation
After starting the automatic editing operation, to end the operation before
the preset OUT point, hold down the ENTRY/SHIFT button and press the
OUT button.
The position where you pressed the button becomes the OUT point, and
editing ends.

DSR-2000/2000P

DMC Editing
You can carry out variable speed editing, controlling the player playback
speed from the recorder.

Carrying Out DMC Editing
Setting the edit points and player speed

Overview of DMC Editing

Use the following procedure.
The following figure illustrates how the tapes move on both the player and
recorder during DMC editing.

Preroll

Display section

Postroll

OUT point

IN point

Recorder

1,7,10

Playback

DMC editing

Playback

Stop

Postroll time × final speed

IN point

1
2

Press the RECORDER button.
Press the ASSEMBLE button or INSERT button to select an edit
mode.

Editing

Press the DMC EDIT button.
The unit switches to the DMC edit mode, and the DMC EDIT button
lights.

Tape
moves at
initial
speed

Playback at stored varying speed
Tape moves at
final speed

Holding down the ENTRY/SHIFT button, press the IN or OUT button
to set an edit point.

Press the PLAYER button, to set the player IN point.

Stop

Editing

Player

56 1

Chapter 4

Preroll time × initial speed

MEMORY indicator

Note

It is not possible to set the player OUT point.
DMC editing can be used for insert or assemble editing, but cannot be used
for audio split editing.
DMC editing cannot be carried out using the i.LINK connector.

Press the SEARCH button or search dial so that the SHUTTLE
indicator in the display section is lit.

Holding down the DMC EDIT button, turn the search dial to set the
initial speed.
To select normal speed as the initial speed, press the PLAY button.
The speed you set appears in the display section.

(Continued)

Chapter 4

Editing

Chapter 4 Editing

1-43

1-1. DSR-2000

When the initial speed setting is complete, release the DMC EDIT
button.

1-1. DSR-2000

1-44

Preread Editing

DMC Editing

Press the PREVIEW button.

Video and audio signals already recorded on the recorder tape can be used
as an edit source for insert editing. This type of editing is called “preread
editing”, as the VCR uses the preread heads to read the signals in advance
from the tape.
The video signals read out by the preread heads can be sent to a video
switcher, and combined with video signals from the player for recording.
The audio signals read out by the preread heads can be sent to an audio
mixer for mixing with audio signals from the player for recording, and can
be recorded either on the original channels or on other audio channels.

The tape is prerolled and then the recorder starts operating at normal
speed and the player at the set initial speed.

10On passing the IN point, the MEMORY indicator begins to flash: turn
the search dial to vary the playback speed.
While the MEMORY indicator is flashing, the speed variations are
stored in memory. On passing the OUT point, the MEMORY indicator
changes from flashing to continuously lit, and the variable speed
storing ends.

Player

If the MEMORY indicator lights continuously before the speed
variation end point
This indicates that the memory became full at that point. Thus even before
the OUT point is reached, it is not possible to record more speed variation.
The maximum capacity is a duration of 120 seconds.

Video source

Audio source

To quit the DMC edit mode
Audio mixer

Video switcher

Hold down the DELETE button and press the DMC EDIT button.

Editing

AUDIO IN
DIGITAL AUDIO(AES/EBU) IN

Editing

ANALOG VIDEO IN
COMPONENT VIDEO IN
S VIDEO IN
SDI INPUT

Press the AUTO EDIT button.
DMC editing is carried out at the stored varying speed.
Once the editing is carried out, the stored speed variation is lost from
memory.

Chapter 4

Digital or analog audio input

Digital or analog video input

To execute the DMC edit

DSR-2000/2000P(recorder)

To check the editing results
Press the REVIEW button.

R-Y

B-Y

Digital or analog video
output (preread signals)
ANALOG VIDEO OUT
COMPONENT VIDEO OUT
S VIDEO OUT
SDI OUTPUT

DSR-2000/2000P

Chapter 4

Editing

Digital or analog audio
output (preread signals)
AUDIO OUT
DIGITAL AUDIO(AES/EBU) OUT

Chapter 4 Editing

DSR-2000/2000P

Special Editing Methods

Preread Editing

Note

• You cannot carry out preread editing using SDTI or i.LINK signals.
• When the preread mode is selected (the PREREAD button is lit), to
prevent feedback in the loop connection, no E-E video out is available,
regardless of the operating mode of the unit. When preread mode is
turned off after preread editing, however, if the same channel remains
connected to both input and output, an E-E signal is output, and feedback
will occur. To prevent this, select PB mode as in step 1 of the following
procedure.
• As for a video switcher, use a model that is not provided with a frame
memory.
To carry out preread editing, use the following procedure.

2,6 1

This section describes the following editing methods.
• Quick editing
After selecting an edit mode, you can save on editing time by setting the
edit points and previewing (or executing) the edit at the same time.
• Continuous editing
When you execute multiple edits in succession, you can edit from the
second time on by setting the player IN and OUT points only.
• Standalone editing
You can carry out editing using as the player an external device, for
example a signal generator, which cannot be controlled remotely through
the REMOTE-IN or REMOTE-OUT connector.
• Manual editing
Without setting edit points in advance, you can carry out editing
manually while watching the monitor screen.
• Adding a narration (Sound-on-sound)
Using this unit alone, it is possible to carry out simple sound-on-sound
editing (such as adding a narration).

Chapter 4

Editing

1
2
3

Press the PB button, turning it on.
Press the PREREAD button, turning it on.
Make the necessary connections for the preread editing. (See the
illustrations on the previous page and on page 129.)
After selecting the desired insert edit mode, carry out the preread
editing.
For details of how to select an edit mode, set edit points, etc., see Chapter 4
“Editing” (page 67).

5
6

Chapter 4

Editing

Press the PREREAD button, turning it off.

Chapter 4 Editing

1-45

1-1. DSR-2000

When the preread editing is completed, remove the connections.

1-1. DSR-2000

1-46
Special Editing Methods

Quick Editing

Press the AUTO EDIT button.
The edit starts.
When the edit finishes, the recorder stops at the OUT point and the
player stops about 2 seconds after the OUT point.

After selecting an edit mode, you can save on editing time by setting the
edit points and previewing (or executing) the edit at the same time.

To edit even more quickly

By skipping the preview in the foregoing procedure, you can execute the
edit even more quickly. To do so, proceed as follows.

1
2

Perform steps 1 through 4 of the foregoing procedure.
Press the AUTO EDIT button.
The edit starts.

5,7 8 6

Stop the tape on the player at the position you wish to make the IN
point.
Press the RECORDER button, turning it on.
Stop the tape on the recorder at the position you wish to make the IN
point.
Press the PREVIEW button.
A preview starts.
The tape positions determined in steps 2 and 4 are set as the player IN
point and recorder IN point, respectively.

The edit ends.
The point where the edit started is set as the IN point, and the point
where the edit ended is set as the OUT point.

Press the PLAYER button, turning it on.

Watching the editing on the monitor, at the position you wish to make
the OUT point, hold down the ENTRY/SHIFT button and press the
OUT button.

Continuous Editing

Editing

3
4

Watching the editing on the monitor, at the position you wish to make
the OUT point, hold down the ENTRY/SHIFT button and press the
OUT button.

Chapter 4

1
2

2,4

When you execute multiple edits in succession, you can edit from the
second time on by setting the player IN and OUT points only.
After execution of an edit, the recorder returns automatically to the OUT
point. Therefore, the recorder OUT point of the current edit becomes the
IN point of the next edit.
OUT point of previous edit =
IN point of next edit

Section edited in previous edit
Recorder

Section edited in next edit

Player
IN point

OUT point

Both the player OUT point and recorder OUT point are set.

Carry out another preview and modify the edit points as required.
For details of how to modify edit points, see the section “Modifying Edit
Points” (page 76).

DSR-2000/2000P

Chapter 4

Editing

Chapter 4 Editing

DSR-2000/2000P

Special Editing Methods

To carry out continuous editing, use the following procedure.

Standalone Editing
This method allows you to use as the player an external device which
cannot be controlled remotely through the REMOTE-IN or REMOTEOUT connector. For example, you can record a color bar signal from a
signal generator in the joints between the scenes of an already completed
tape.

For standalone editing, use the following procedure.

1
34

1
2

Press the PLAYER button, turning it on.
Set the player IN and OUT points.
For details of how to set IN and OUT points, see the section “Setting Edit
Points” (page 72).

4
1

In the input selection section, select the signal being generated by the
signal generator connected to the unit.

Press the AUTO EDIT button.

For details of the input selection section, see page 14.

The edit starts.
When the edit finishes, the recorder stops at the OUT point and the
player stops about 2 seconds after the OUT point.

Press both the PLAYER button and RECORDER button, turning them
off.

Set the IN point and, if necessary, also OUT point.

To stop the edit
Press the ENTRY/SHIFT button together with the OUT button.
The edit ends, and the point where you pressed the buttons becomes
the OUT point.
To abort the edit
Press the STOP button.
By repeating this process, you can carry out continuous editing.

Editing

Press the PREVIEW button to carry out a preview.

Chapter 4

On the recorder, the OUT point for the previous edit becomes the new
IN point.

3
4

The AUTO EDIT button flashes.
For details of how to set IN and OUT points, see the section “Setting Edit
Points” (page 72).

Press the AUTO EDIT button.
The edit is carried out.

With extended menu item 326, a setting can be made so that the preceding OUT
point automatically becomes the new IN point.

Chapter 4

Editing

Chapter 4 Editing

1-47

1-1. DSR-2000

1-48
Special Editing Methods

Manual Editing

Adding a Narration (Sound-on-Sound)
To carry out manual editing, start playback on the player beforehand, then
use the following procedure.

4,6 1

By means of preread editing with an audio mixer connected (see page 87),
you can mix in an audio signal with the existing recorded soundtrack, but
extension menu item 819 provides a simple sound-on-sound editing
function for adding a narration, using this unit alone.
To add a narration from microphone input
As an example, the following procedure describes how to record a
narration mixed with audio channels 1 and 2 already recorded on the tape,
when the microphone is connected to input audio channel 1.

3
1
2

After checking the above settings, use the following procedure.
Press the RECORDER button, turning it on.

Use the search dial in jog or shuttle mode to find the edit start point
(the recorder IN point), and stop the tape just before this point.

Extension menu item 819 settings (on monitor screen)

Select an edit mode.

Editing

AUDIO INPUT SOURCE
ARRANGE

Editing

ITEM-819

For details of how to select an edit mode, see the section “Selecting an Edit
Mode” (page 71).

Set extension menu item 819 as follows.
Chapter 4

Chapter 4

5 7

In this case, first connect the microphone to the AUDIO IN CH-1
connector, and set the audio input and editing mode as follows.
• In the input selection section (see page 14), with the CH1, 1/2 button,
select an analog audio signal.
• In the edit mode setting section (see page 20), press the INSERT CH-1
and CH-2 buttons, turning them on.

Recording channel numbers

in1 in2 in3 in4 tape
-------------------on
ch1: on
ch2: on
on
ch3:
ch4:

Press the PLAY button.
The recorder begins playback.
Note

It takes about two seconds until the playback video stabilizes. For this
reason, start the playback from before the segment of video you wish
to use.

Input channel numbers

At the edit start point (the recorder IN point), press the EDIT button
and PLAY button simultaneously.
The edit starts.

At the edit end point (the recorder OUT point), press the PLAY button.

Press the STOP button to stop the recorder playback.

For details of extension menu item 819 settings, see page 123.

2
3

Press the MIXING button in the upper control panel, turning it on.
Carry out insert editing on audio channels 1 and 2 (CH-1 and CH-2)
while reciting the narration into the microphone.

The edit ends, and the recorder continues with playback.

DSR-2000/2000P

Chapter 4

Editing

Chapter 4 Editing

DSR-2000/2000P

Chapter

ClipLink Operation

Overview of ClipLink Operation
The ClipLink function provides the following.
• Displaying ClipLink log data
• Cueing up to Mark IN/OUT points and cue points
• Rewriting ClipLink log data (reel numbers, Mark IN/
OUT points, and OK/NG status only)
• Creating additional ClipLink log data and deleting
ClipLink log data (Mark IN/OUT points only)
• Automatically creating new ClipLink log data (Mark
IN/OUT points only)
When Mark IN/OUT points are created, the scene
number and take number for them are fixed at 000 and
00, respectively.

For an overview of the ClipLink function, see the appendix “
ClipLink Guide” (page 147).

Chapter 5

The above operations other than automatic creation of
new ClipLink log data require the ClipLink log data
list display.

Notes

• For a tape on which index pictures are already
recorded, you cannot change any ClipLink log data
other than the reel numbers and OK/NG status.
(When index pictures are recorded on a tape, the
ClipLink log data list for the tape shows an IP
indication.)
• You cannot carry out ClipLink operation such as
“Continue” on the DSR-1/1P or DSR-300/300P/
500WS/500WSP for a tape whose ClipLink log data
has been modified on this unit.

ClipLink Operation

1-49

1-1. DSR-2000

Chapter 5 ClipLink Operation

To display ClipLink log data, hold down the ENTRY/
SHIFT button and press the LIST/– button.

Cuing Up to Mark IN/OUT and Cue Points

Detailed Data Display
To check more details related to the data item selected
on the ClipLink log data list, proceed as follows.

LIST/– button

ENTRY/SHIFT button

1
The following ClipLink log data list appears in the
monitor.

Cuing Up to Any Desired
Position

Using the search dial, move the selection mark
(asterisk) to the data item for which you wish to
display details.

When the selected data item display contains
“C” mark
The cue point address is stored as the IN point and
the IN button on the control panel lights.

To return to the original monitor display
To exit from the ClipLink log data list and return to the
original monitor display, hold down the ENTRY/
SHIFT button and press the LIST/– button.

DSR-2000/2000P

Chapter 5 ClipLink Operation

Operate as follows.
• To cue up to the mark IN point or cue point
Holding down the IN button, press the PREROLL
button.
• To cue up to the mark OUT point
Holding down the OUT button, press the
PREROLL button.

To cue up to the Mark IN point or cue point
following the current point selected on the list
Holding down the MARK/+ button, press the F FWD
button.
During the cue-up operation is in progress, the F FWD
button flashes.

This exits from the ClipLink log data list and cues
up to the selected position.

Chapter 5 ClipLink Operation

ClipLink Operation

Mark IN point
display (cue point
and index picture
addresses not
displayed)

To cue up to the Mark IN point or cue point
preceding the current point selected on the
list
Holding down the MARK/+ button, press the REW
button.
During the cue-up operation is in progress, the REW
button flashes.

Chapter 5

Data serial number

Using the search dial, move the selection mark
(asterisk) to the desired data item on the ClipLink
log data list.
When the selected data item display contains
“M” mark
The Mark IN point address is stored as the IN point
and the Mark OUT point address is stored as the
OUT point. At the same time, the IN button and
the OUT button on the control panel light.

Mark IN/cue timecode
M = Mark IN point indication
C = cue point indication
I = Index picture address indication

F FWD button

MARK/+ button

CLIPLINK LOG DATA LIST
(003/196)
00:03:50:00
00:04:03:00
OK
001
03

REW button

Press the SEARCH button.

MARK IN
MARK OUT
OK/NG
SCENE NO
TAKE NO

Once you select data on a ClipLink log data list, you
can cue up to the point preceding or following the
selected data with ease without reverting to the
ClipLink log data list.

CLIPLINK LOG DATA LIST
(003/196)

OK/NG status or
IP (index picture)
indication

Cuing Up to Adjacent Mark IN/
Cue Points

To cue up to the point specified by the data item
selected on the ClipLink log data list, proceed as
follows.

While you hold the SEARCH button down, the
detailed data display appears.
REEL NO
XXXXXXXX
1 M 00:01:23:00 OK
2 M 00:02:35:00 OK
* 3 M 00:03:50:00 OK
4 M 00:04:03:00 OK
5 M 00:04:48:00 NG
6 M 00:04:53:00 OK
7 M 00:05:08:00 OK
8 I 00:06:13:00 IP

1-1. DSR-2000

1-50

Displaying ClipLink Log Data

DSR-2000/2000P

Rewriting ClipLink Log Data
You can rewrite the reel number, Mark IN/OUT points
and OK/NG status included in the ClipLink log data.

Repeat steps 3 and 4 until the settings for all digits
are complete.

When all digits have been set, hold down the
ENTRY/SHIFT button and press the MARK/+
button.

Changing the Reel Number
To change the reel number of the data item selected on
the ClipLink log data list, proceed as follows.

Hold down the STOP button and press the SET
button.

Perform either one of the following operations.
• Hold down the ENTRY/SHIFT button and press
the LIST/– button, exiting from the ClipLink log
data list.
• Cue up to the IN point or OUT point. (See page
99.)

Cue up to the tape position to be made the new
Mark IN point. (See page 72.)

Holding down the IN button, press the ENTRY/
SHIFT button.

This returns to the original ClipLink log data list.
Note

If you carry out step 7 skipping step 6, the original
ClipLink log data list appears again on the monitor
and, in this case, the reel number is not rewritten.

6
1
2

2,7

Using the search dial, move the selection mark
(asterisk) to the desired data item on the ClipLink
log data list.
Hold down the STOP button and press the SET
button.

*REEL NO

REEL NO

(XXXXXXXX)

Cue up to the tape position to be made the new
Mark OUT point. (See page 72.)

Holding down the OUT button, press the ENTRY/
SHIFT button.

7
2,7 8

Turn the search dial to select the digit to change.

100

Chapter 5 ClipLink Operation

1,3,5

2,5

Using the serarch dial, move the selection mark
(asterisk) to the desired data item on the ClipLink
log data list.

Hold down the STOP button and press the SET
button.

CLIPLINK LOG DATA LIST
(003/196)
*

Holding down the ENTRY/SHIFT button, press
the LIST/– button to display the ClipLink log data
list, then make sure the selection mark (asterisk) is
kept at the position of the desired data item
selected in step 1.

Holding down the ENTRY/SHIFT button, press
the MARK/+ button.
The ENTRY/SHIFT button goes out and the Mark
IN point and Mark OUT point addresses are
rewritten.

3 M 00:03:50:00 OK

OK/NG

Hold down the SEARCH button and turn the
search dial to change the setting to OK or NG as
required.

Holding down the ENTRY/SHIFT button, press
the MARK/+ button.
The OK/NG status is rewritten.
(Continued)

Chapter 5 ClipLink Operation

101

1-51

1-1. DSR-2000

Hold down the SEARCH button and turn the
search dial to change the digit indicated by an
arrow (µ).

The following setting screen appears.

If the selection mark (asterisk) is at a wrong
position
Using the search dial, return the selection mark to
the desired data item.

The Mark OUT point address changes.

(YYYYYYYY)

Rotating the search dial clockwise moves the
current digit position to the right, and
counterclockwise moves it to the left.

When Mark IN/OUT points are rewritten to the
cassette memory, the frame digits of the address data
are processed as follows.
For Mark IN point: Any frame-digits value is
counted as 1 second.
For Mark OUT point: Any frame-digits value is
ignored.

The ENTRY/SHIFT button lights and the Mark IN
point address changes.

To change the OK/NG status of the data item selected
on the ClipLink log data list, proceed as follows.

ClipLink Operation

CLIPLINK LOG DATA LIST
(003/196)

To change Mark IN/OUT points selected on the
ClipLink log data list, perform the following
procedure.

Changing the OK/NG Status

Chapter 5

The following setting screen appears.

Changing Mark IN/OUT Points

Using the search dial, move the selection mark
(asterisk) to the desired data item on the ClipLink
log data list.
The Mark IN point address is stored as the IN
point and the Mark OUT point address is stored as
the OUT point. At the same time, the IN button
and OUT button light and the ENTRY/SHIFT
button starts flashing.

The reel number changes.

7
1,3

Hold down the STOP button and press the SET
button.

You can add new Mark IN/OUT point data to the
ClipLink log data or delete Mark IN/OUT point data
from the ClipLink log data.

This returns to the original ClipLink log data list.
Note

If you carry out step 5 skipping step 4, the original
ClipLink log data list appears again on the monitor
and, in this case, the OK/NG status is not rewritten.

1-1. DSR-2000

1-52

Adding to/Deleting From ClipLink Log Data

Rewriting ClipLink Log Data

Holding down the ENTRY/SHIFT button, press
the MARK/+ button.
The ENTRY/SHIFT button goes out, and the Mark
IN point and Mark OUT point data is added to the
end of the existing ClipLink log data.

Adding Mark IN/OUT Points

Note

Set the setup menu item 129 (CLIPLINK) to ON
beforehand, then proceed as follows.

The volume of ClipLink log data that can be stored
in a cassette memory depends on the cassette
memory capacity as follows.

For information about how to operate the setup menu, see
Chapter 6 “Setup Menu” on page 107.

Cassette memory
capacity

Storable volume of data

4K bits

45 pairs of Mark IN and
Mark OUT points

16K bits

198 pairs of Mark IN and
Mark OUT points

When adding to the existing ClipLink log data,
carefully watch the ClipLink log data list not to
allow the additional data to exceed the available
cassette memory capacity.

Deleting Mark IN/OUT Points

1,3

After displaying the ClipLink log data, proceed as
follows.
Cue up to the tape position you wish to make an
additional Mark IN point. (See page 72.)

Holding down the IN button, press the ENTRY/
SHIFT button.

Chapter 5

ClipLink Operation

The IN button lights, and the Mark IN point
address is set.

Cue up to the tape position you wish to make an
additional Mark OUT point. (See page 72.)

Holding down the OUT button, press the ENTRY/
SHIFT button.
The OUT button and ENTRY/SHIFT button light,
and the Mark OUT point address is set.

3
1

Using the search dial, move the selection mark
(asterisk) to the desired data item on the ClipLink
log data list.
(Continued)

DSR-2000/2000P

102

Chapter 5 ClipLink Operation

103

DSR-2000/2000P

Adding to/Deleting From ClipLink Log Data

Holding down the DELETE button, press the
MARK/+ button.
The specified data disappears from the ClipLink
log data list.

Holding down the ENTRY/SHIFT button, press
the MARK/+ button.
Note

If you exit from the ClipLink log data list skipping
step 3, the previous data is restored. The data
specified for deletion is not deleted.

Automatically Creating New ClipLink Log Data
When the setup menu item 129 (CLIPLINK) is set to
ON, you can automatically create new Mark IN/OUT
points during recording or editing operation.

To erase ClipLink log data
After displaying the ClipLink log data list, proceed as
follows.

For information about how to operate the setup menu, see
Chapter 6 “Setup Menu” on page 107.

New Mark IN/OUT points are created as follows.
Operation

Automatic creation of Mark IN/OUT points

Recording

The recording starting point is made a Mark
IN point and the recording ending point is
made a Mark OUT point.

Editing

The edit IN point (the video IN point or audio
IN point whichever coming first) is made a
Mark IN point and the edit OUT point is made
a Mark OUT point.

Notes

Holding down the DELETE button, press the
LIST/– button.
The data shown on the ClipLink log data list
disappears.

Holding down the ENTRY/SHIFT button, press
the MARK/+ button.
The message “NO CLIPLINK LOG DATA”
appears on the screen and the ClipLink log data is
completely erased.
Chapter 5

Chapter 5

• If recording or editing is carried out when the setup
menu item 129 (CLIPLINK) is set to OFF, the
existing ClipLink log data is erased.
• If you carry out recording or editing on a tape on
which index pictures are already recorded, the
existing ClipLink log data for the tape is lost.
• The Mark IN/OUT point data automatically created
during recording or editing operation for a tape on
which no index pictures are recorded is added to the
end of the existing ClipLink log data for the tape.
In this case, if you carry out recording or editing on a
tape position linked to the existing ClipLink log data,
the link between them is lost. Therefore, when you
start creating new ClipLink log data, where on the
tape to start recording or editing must be determined
very carefully. If the existing ClipLink log data is
no longer required, erase it beforehand.

ClipLink Operation

Chapter 5 ClipLink Operation

105

1-53

1-1. DSR-2000

104

1-1. DSR-2000

1-54

Chapter

Setup Menu

Menu System Configuration
The setup menu system of this unit comprises the basic For detailed information about menu operation relating to
the digital hours meter, see “Digital hours meter” (page
menu and extended menu.
136).
• Basic menu
This menu is used to make settings relating, for
• Extended menu
example, to the following.
This menu is used to make a wide range of settings
– the digital hours meter
relating to the functions of this unit, for example, the
– the preroll time
control panel functions, video and audio control, and
– the text information superimposed on the video
digital data processing.
output to the monitor
– the menu banks for retaining menu settings

Basic Menu
Items in the Basic Menu
Chapter 6

In the “Settings” column of the table, the factory
default settings are indicated by an enclosing box.

Setup Menu

The basic menu items (excluding the items related to
the digital hours meter) are listed in the following
table.

DSR-2000/2000P

Chapter 6

Setup Menu

107

DSR-2000/2000P

Basic Menu

Items in the basic menu (continued)

Items in the basic menu
Item number

Item name

Settings

Item number

Item name

Settings

001

PREROLL TIME

0S... 5S ...30S: Set the preroll time to between 0 and 30 seconds in steps of 1 second.
A preroll time of at least 5 seconds is recommended when using this unit for editing.

011 a)

CHARACTER VSIZE

002 a)

CHARACTER
H-POSITION

Adjust the horizontal screen position (as a hexadecimal value) of the text information
output from the VIDEO OUT 3 (SUPER) connector and SDI OUTPUT 3 (SUPER)
connector for superimposed display on the monitor.

Determine the vertical size of characters such as time code output from the VIDEO OUT
3 (SUPER) connector and SDI OUTPUT 3 (SUPER) connector for superimposed
display on the monitor.

00... 0A ...2A (DSR-2000) /00... 09 ...29 (DSR-2000P): The hexadecimal value 00 is for
the far left of the screen. Increasing the value moves the position of the characters to
the right.
003 a)

004

005

CHARACTER
V-POSITION

SYNCHRONIZE

DISPLAY
INFORMATION
SELECT

×1 : Standard size
×2: 2 times standard size
015

MENU DISPLAY

Adjust the vertical screen position (as a hexadecimal value) of the text information
output from the VIDEO OUT 3 (SUPER) connector and SDI OUTPUT 3 (SUPER)
connector for superimposed display on the monitor.

BLACK: Black letters on a white background.

00... 2E ...38 (DSR-2000)/00... 37 ...43 (DSR-2000P): The hexadecimal value 00 is for
the top of the screen. Increasing the value lowers the position of the characters.

B/OUT: Black letters with white outline.

When editing using this unit as a controller and an external VCR connected to this unit
via a 9-pin remote control cable or i. LINK/DV cable, this item determines whether or not
to operate the two units in phase synchronization.

WHITE : White letters on a black background.
W/OUT: White letters with black outline.
016

ALARM

ON : Operate in phase synchronization.

LIMIT : Display alarm messages only during recording or editing.

OFF: Do not operate in phase synchronization.
Determine the kind of text information to be output from the VIDEO OUT 3 (SUPER)
connector and SDI OUTPUT 3 (SUPER) connector when the CHARACTER switch on
the subsidiary control panel is set to ON.

ON: Display alarm messages.
017

SUB STATUS
Select supplementary status information superimposed on the output from the VIDEO
DISPLAY SELECT OUT 3 connector and SDI OUT 3 connectors to the monitor.
OFF : Nothing of supplementary status information
TIC MODE: Indications of the operating mode of internal time code generator

T&UB: Time data and user bit data. (When U-BIT is selected with the COUNTER SEL
button, the user bit data and time data arranged in that order are displayed.)
T&CNT: Time data and counter count. (When COUNTER is selected with the
COUNTER SEL button, the counter count and time data arranged in that order are
displayed.)

007

MONITORING
SELECTION FOR
VTR-TO-VTR
EDIT
CHARACTER
TYPE

099

MENU GRADE

For setup menu operations, select whether to display the basic menu information only or
both the basic menu information and the extended menu information.

T&T: Time data and time code (TC or VITC).

BASIC : Display the basic menu information only.

TIME: Timecode (TC or VITC) only.

ENHAN: Display both the basic menu information and the extended menu information.

DATE: Recording date and time.
Determine which tape transport control buttons on the control panel are enabled when
this unit is controlled from external equipment.
DIS: All buttons and switches are disabled.

a) When setting items 011 and 015, watch the monitor screen, and adjust to the required state.
Item number

Item name

Settings

B01

RECALL BANK 1

Set to ON to recall menu settings from menu bank 1.

ST&EJ : Only the STOP button and EJECT button are enabled.

B02

RECALL BANK 2

Set to ON to recall menu settings from menu bank 2.

ENA: All buttons and switches except the RECORDER button and PLAYER button are
enabled.
Determine whether to display the counter in 12-hour mode or 24-hour mode.

B03

RECALL BANK 3

Set to ON to recall menu settings from menu bank 3.

B04

RECALL BANK 4

Set to ON to recall menu settings from menu bank 4.

+ –12H : 12-hour mode

B11

SAVE BANK 1

Set to ON to save current menu settings to menu bank 1.

24H: 24-hour mode
For editing with two DSR-2000/2000P units, determine whether the recorder unit is
forced into E-E mode when the recorder PLAYER button is pressed to view the player
playback signals on the monitor.

B12

SAVE BANK 2

Set to ON to save current menu settings to menu bank 2.

B13

SAVE BANK 3

Set to ON to save current menu settings to menu bank 3.

B14

SAVE BANK 4

Set to ON to save current menu settings to menu bank 4.

Setup Menu

009 a)

TAPE TIMER
DISPLAY

AUDIO MIX MODE: Indications of input audio mixing
TAPE REMAIN: Remaining capacity of the tape

Chapter 6

Chapter 6 Setup Menu

008

LOCAL
FUNCTION
ENABLE

Select whether or not to display alarm messages.
OFF: No alarm messages.

T&STA : Time data and the units status.

006

Determine the type of characters in menu text output from the VIDEO OUT 3 (SUPER)
connector and SDI OUTPUT 3 (SUPER) connector for superimposed display on the
monitor.

MANU : Do not force the recorder into E-E mode.
AUTO: Force the recorder into E-E mode.
Determine the type of characters such as time code output from the VIDEO OUT 3
(SUPER) connector and SDI OUTPUT 3 (SUPER) connector for superimposed display
on the monitor.
WHITE : White letters on a black background.
BLACK: Black letters on a white background.
W/OUT: White letters with black outline.
B/OUT: Black letters with white outline.

108

Chapter 6 Setup Menu

(Continued)
Chapter 6 Setup Menu

109

1-55

1-1. DSR-2000

a) When setting items 002, 003, and 009, watch the monitor screen, and adjust to the required state.

1-1. DSR-2000

1-56
Basic Menu

Basic Menu Operations
This section describes the basic menu display and how
to change the settings.

To display the item group name
Items in the menu are arranged in groups, by the 100's
digit of the item number. To display the name of the
group to which the currently selected item belongs,
hold down the VARIABLE button.

The setting value changes at a rate depending on
the search dial position (when the SHUTTLE
indicator is lit) or on the search dial rotation rate
(when the JOG indicator is lit).

Changing the currently displayed menu
item

Search dial

For information about how to use items B01 to B14, see the
section “Menu bank operations (menu items B01 to B14)”
(page 112).

SHUTTLE/JOG indicator

Item group name

Displaying the menu

MENU button
Display section

SHUTTLE
JOG

To display menus on the monitor
Set the CHARACTER switch on the subsidiary control
panel to ON, then press the MENU button.
You can now view the menu as shown in the following
figure on a monitor connected to the VIDEO OUT 3
(SUPER) connector or SDI OUTPUT 3 (SUPER)
connector.
Group name for the
currently selected item

F FWD button

Press the MENU button.
The F FWD button and VARIABLE button light and
the setting of the currently selected menu item appears
in the display section of the lower control panel.

Cursor indicating the
currently selected
item

HOUR METER
*HO1:OPE HOURS
HO2:DRUM HOURS -

-------

VARIABLE button

102
52

Setting value (flashes while changing)

When the desired setting value is displayed, press
the SET button.

VARIABLE button

This saves the new setting value, and the menu
display disappears from the display section.
Turn the search dial.
Turning the search dial clockwise increments the item
number, and turning it counterclockwise decrements
the item number.
When you turn the search dial, the item number
changes at a rate depending on the search dial position
(when the SHUTTLE indicator is lit) or on the search
dial rotation rate (when the JOG indicator is lit).
To skip from one item group to the next
Hold down the VARIABLE button, and turn the search
dial.

To abandon making a change
Press the MENU button before pressing the SET
button.
The menu display disappears from the display
section without the new setting value being saved.

Resetting the menu settings to their
factory default values

13 2
Changing a menu item setting value
To change the setting value of the currently displayed
menu item, use the following procedure.

Chapter 6

Setting

1
To display the full item name
Hold down the F FWD button.

DSR-2000/2000P

110

Chapter 6 Setup Menu

Press the MENU button.
The menu appears in the display section.

1
Item name

Setup Menu

Chapter 6 Setup Menu

2
Item number (flashing)

Hold down the SEARCH button, and turn the
search dial.

2
3

Press the RESET button.
Press the SET button.
The menu settings are reset to their factory default
settings.
Chapter 6 Setup Menu

111

DSR-2000/2000P

Basic Menu

Extended Menu

Menu bank operations (menu items B01 to
B14)

Items in the Extended Menu

This unit allows four different complete sets of menu
settings to be saved in what are termed "menu banks"
numbered 1 to 4. Saved sets of menu settings can be
recalled for use as required.
To jump to menu item B01
You can recall any required menu by turning the
search dial after pressing the MENU button.
If you press the MENU button first, then the
COUNTER SEL button, you can jump directly to
menu item B1 or H01. The recalled menu item toggles
between B01 and H01 every time you press the
COUNTER SEL button.

The extended menu contains the following items.
In the Settings column of the table, the factory default
settings are indicated by an enclosing box.
Menu items in the 100s, relating to the control panels
Item number

Item name

Settings

101

SELECTION FOR
SEARCH DIAL
ENABLE

Select how the unit enters the search mode.
DIAL : Press the SEARCH or VARIABLE button or, except during recording/editing, turn
the search dial.

MAXIMUM TAPE
SPEED

Specify the maximum tape speed in search mode (shuttle) or F.FWD (fast forward)/
REW (rewind) mode.

KEY: Press the SEARCH or VARIABLE button.
102

Sub-item
1

SHUTTLE

Specify the maximum tape speed in search mode (shuttle).
X16: Maximum 16 times normal

Saving the current active menu settings
Set one of menu items B11 SAVE BANK 1 to B14
SAVE BANK 4 to ON, depending on which of the
menu banks you wish to save in, then press the SET
button.

X32 : Maximum 32 times normal
X60: Maximum 60 times normal
2

F.FWD/REW

Specify the maximum tape speed in F.FWD/REW mode.
X32: Maximum 32 times normal
X60: Maximum 60 times normal

Recalling settings from a menu bank
Set one of menu items B01 RECALL BANK 1 to B04
RECALL BANK 4 to ON, depending on which of the
menu banks you wish to recall from, then press the
SET button.

X85 : Maximum 85 times normal
MAX: No maximum tape speed is specified.
Note
When this item is set to MAX, the playback video signal is muted.
105

REFERENCE
SYSTEM ALARM

Recall
Current active
menu settings

Save

Select whether or not to display a warning when the reference video signal is not
supplied or is out of phase with the input video signal.
OFF: No warning.
LIMIT : Flash the STOP button as a warning only when the reference video signal is out
of phase with the input video signal.

Menu bank 1

ON: Flash the STOP button as a warning.
107
Recall

REC INHIBIT
LAMP FLASHING

Select whether to keep lit or flash the REC INHIBIT indicator when recording is
prevented with the REC INHIBIT switch on the subsidiary control panel set to OFF.
OFF : Light the REC INHIBIT indicator.

Menu bank 2

ON: Flash the REC INHIBIT indicator.
108

AUTO EE
SELECT

When a cassette is inserted and the PB/EE button is lit,select the operation modes in
which input video and audio signals are automatically handled in E-E mode.

Save

STOP: In STOP mode
Menu bank 3

109

FORCED EE
WHEN TAPE
UNTHREAD

During tape threading and unthreading, or when no cassette is inserted, select whether
the PB/EE button controls the output signal PB/EE setting.

Setup Menu

S/F/R : In STOP/F FWD (fast-forward)/REW (rewind) modes
Recall

Chapter 6

Chapter 6 Setup Menu

Save

ON : No control (the signal is always an E-E signal).
OFF: Control.

(Continued)

Recall
Save

Chapter 6 Setup Menu

113

1-57

1-1. DSR-2000

112

Menu bank 4

1-1. DSR-2000

1-58
Extended Menu

Menu items in the 100s, relating to the control panels (continued)
Item number
116

Item name
JOG DIAL
RESPONSE

Settings
Select the tape speed characteristics for the search dial rotation rate in jog mode.

Item number

Item name

129

CLIPLINK

Menu items in the 100s, relating to the control panels (continued)
Settings

ON: Create.

TYPE2: Tape speed varies stepwise as shown in the figure belowa) over the range –3 to
+3. (Characterized by a zone around –1 and +1 where the tape speed is independent
of the rotation rate)

When recording, the recording starting point is made a Mark IN point and the recording
ending point is made a Mark OUT point. When editing, the edit IN point (the video IN
point or audio IN point whichever coming first) is made a Mark IN point and the edit OUT
point (the video OUT point or audio OUT point whichever coming second) is made a
Mark OUT point.

TYPE3: Tape speed varies linearly over the range –3 to +3, as shown in the figure
belowb).
117

CONTROL PANEL Select the control panel function when the CONTROL PANEL switch on the subsidiary
SELECTION
control panel is set to EXT.

Note
If recording or editing is carried out when this item is set to OFF, the existing ClipLink
log data is erased.

SW : Only the control panel connected to the CONTROL PANEL control connector on
the connector panel functions.
PARA: Both the control panel connected to the CONTROL PANEL connector and the
control panel of this unit function.
118

130

DISPLAY DIMMER Set the brightness of the audio level meters.
CONTROL
0 ... 1 ...6 : Set in this range. 0 is the brightest, and 6 the dimmest.

Select whether the REMOTE button on the upper control panel is enabled.

Item number

Item name

DIS : Disabled.

201

PARA RUN

KEY INHIBIT
Select which switches and buttons can be operated when the KEY INHIBIT switch on
SWITCH
the subsidiary control panel is set to ON. The following sub-items control different sets
EFFECTIVE AREA of switches and buttons independently.
Sub-item
1

REMOTE
SELECT

MON./ INPUT
SEL

Select whether the buttons in the input selection section on the upper control panel and
the MONITOR SELECT buttons on the lower control panel are enabled.

ENA: Use synchronized operation.
Note
To use synchronized operation for two or more VCRs, set this item to ENA on all of the
VCRs.

Select which switches and buttons on the control panel of this unit as well as the
external control panel connected to this unit are enabled.
DIS : All switches and buttons are disabled.

119

Item number

Item name

ENA: All switches and buttons are enabled.

301

VAR SPEED
Select the playback speed range when carrying out playback in variable mode from a
RANGE FOR
remote control unit connected to the REMOTE-IN connector or REMOTE-OUT
SYNCHRONIZATION connector.
–1~+1: –1~+1 times normal speed.

OFF : –1 to +2 times normal speed
ON: 0 to +1 times normal speed.
Select whether to rewind the tape automatically when recording or playback reaches the
end of a tape.

AUTO REW

305

SYNC GRADE

+3
(reverse)

RVS

DSR-2000/2000P

114

FWD

-3

Chapter 6 Setup Menu

STILL: Stationary.

FWD

±0.03~±1: Speed set in the range ±0.03 to ±1 (select from ±1, ±0.5, ±0.03, ±0.2, ±0.1.)

Rotation rate
-1

RVS

Rotation rate
RVS

FWD

RVS

Select the initial speed automatically set when carrying out DMC editing.
MANUAL : The speed determined by the rotation of the search dial.
PLAY: Normal playback speed.

Speed

TYPE 3

FWD

DMC INITIAL
SPEED

(Continued)

-3

Chapter 6 Setup Menu

115

Setup Menu

Speed

TYPE 2

306

Chapter 6

Chapter 6 Setup Menu

ROUGH: ±1 frame accuracy.

(Continued)

–1.5 ~+2 : –1.5 ~+2 times normal speed
When editing in phase-synchronized mode with item 004 set to ON, select the target
phase synchronization accuracy.
ACCUR : ±0 frame accuracy.

DIS: Do not rewind the tape automatically.
ENA : Rewind the tape automatically.

Menu items in the 300s, relating to editing operations
Settings

EDIT: All switches and buttons for editing operations are disabled.
Select the playback speed range when carrying out playback in variable mode from the
control panel of this unit.

VARIABLE
SPEED LIMIT IN
KEY PANEL
CONTROL

125

Select whether or not to use synchronized operation for two or more VCRs.
DIS : No synchronized operation.

ENA: Enabled.
CONTROL
PANEL

Menu items in the 200s, relating to the remote control interface
Settings

ENA: Enabled.

DIS : Disabled.
3

Select whether to create ClipLink log data.
OFF : Do not create.

TYPE1 : Tape speed varies linearly over the range –1 to +1.

DSR-2000/2000P

Extended Menu

Menu items in the 300s, relating to editing operations (continued)
Settings

Item number

Item name

307

AUTO-DELETION
FOR
INCONSISTENT
DATA

Select what happens when an erroneous edit point is set.

Item number

Item name

318

EDIT RETRY

Menu items in the 300s, relating to editing operations (continued)
Settings

MANU : A warning is given by flashing the DELETE button on the lower control panel.
The operator must manually delete the unnecessary edit point .
NEG&E: When inconsistent edit points are set, such as when an OUT point is before an
IN point, or an audio OUT point is before an audio IN point, or when too many edit
points are specified, the previously set edit point is deleted.

OFF: Editing is not carried out, and the unit stops.
ON : The editing is automatically retried (up to twice).
319

PREREAD
SELECT

NEG: When inconsistent edit points are set, such as when an OUT point is before an IN
point, or an audio OUT point is before an audio IN point, the previously set edit point
is deleted. When too many edit points are specified, the DELETE button on the
control panel flashes to give a warning.

AUDIO: Preread for audio only.
The preread operation can be controlled with the PREREAD button on the control panel
or from the 9-pin remote control interface.

Pressing the button corresponding to an edit point to be deleted and the DELETE button
simultaneously deletes the edit point. If an erroneous edit point is set (the DELETE
button is flashing), editing is not executed.
SELECTION OF
STD/NON-STD
FOR ANALOG
VIDEO IN

326

AUTOMATIC IN
ENTRY AFTER
AUTO EDIT

STD : Synchronize. Use this setting when a standard signal is always input (forced STD
mode).

ANALOG AUDIO
EDIT PRESET
REPLACE FOR
CH1

Items 311 to 314: When using an editor (PVE-500, BVE-600, etc.) or a remote controller
which cannot control digital audio edit preset, select how to activate edit preset of each
digital audio channel on this unit using the analog audio edit preset function of the editor
or remote controller.

312

ANALOG AUDIO
EDIT PRESET
REPLACE FOR
CH2

Set edit preset of each digital audio channel (channels 1 to 4) of this unit on or off
according to the analog audio preset specified by the remote controller or editor.

314

AUDIO MODE
CHANGE

ANALOG AUDIO
EDIT PRESET
REPLACE FOR
CH4
AUDIO EDIT
MODE

Select whether to allow audio data recorded on tape in two-channel mode (or fourchannel) to be re-recorded in four-channel (or two-channel mode).
OFF : Do not allow re-recording in a different audio mode.
ON: Allow re-recording in a different audio mode.
When this item is set to ON, the type of editing for audio signals is always a cut editing.

335

OUT
REFERENCE
SELECT

When signals are input to both of the REF. VIDEO IN connector and the VIDEO IN
connector, determine which input signal to use as the reference signal.
REF VIDEO : Use the signal input to a REF. VIDEO IN connector as the reference video
signal.
The input video signal to be edited is required to be in synchronization with the
reference video signal.

NO DEFINITION
ANALOG CH1: Follow edit preset of analog channel 1.
ANALOG CH2: Follow edit preset of analog channel 2.
ANALOG CH1+CH2: Follow edit preset of analog channel 1 or 2.
The default settings for each item are as follows:

VIDEO INPUT: Use the input video signal selected with the VIDEO INPUT button in the
INIPUT SELECT section.
Menu items in the 400s, relating to preroll
Settings

311: ANALOG CH1

Item number

Item name

312: ANALOG CH2

401

FUNCTION MODE Select the state that the unit goes into after a cuing-up operation.
AFTER CUE-UP
STOP : Stops (the STOP mode).

313: NO DEFINITION
314: NO DEFINITION

STILL: Still playback (in search mode).

Specify the type of editing for audio signals.

Note

CUT: Cut editing (discontinuity in audio signal may result at the editing point, causing
noise during playback.)

When controlling this unit from the BVE-800 editor, set this item to STOP.

IN/OUT

AUTOMATIC
PREROLL
REFERENCE
ENTRY

Select whether or not the edit IN point is automatically set by pressing the PREROLL
button when the IN point is not set before starting preroll.
DIS : IN point is not set automatically.
ENA: I N point is set automatically.

Setup Menu

403

CROSS FADE : Cross-fade

Chapter 6

Chapter 6 Setup Menu

317

ANALOG AUDIO
EDIT PRESET
REPLACE FOR
CH3

OFF : No automatic setting.
R & P: Set recorder IN point automatically, and also player IN point in two-VCR editing.

327

When using a VCR with no built-in time base corrector (e.g. a home-use VHS-system
VCR), select N-STD.
311

Select whether or not to automatically set the OUT point of the previous edit as the next
IN point at the end of an automatic edit.
R: Set recorder IN point automatically.

When no signal is input to the REF. VIDEO IN connector, select whether or not to
synchronize the playback circuits with the input analog video signal.

N-STD: Do not synchronize. Use this setting when the input video signal is unstable
(forced NON-STD mode).

313

Specify the preread editing operation.
A/V : Preread for both audio and video.
VIDEO: Preread for video only.

Note

308

When editing with two DSR-2000/2000P units, select the operation if the recorder was
not synchronized in time. (Make this setting on the recorder.)

FADE: Fade in and fade out
IN

OUT

116

Chapter 6 Setup Menu

117

1-59

1-1. DSR-2000

(Continued)

1-1. DSR-2000

1-60
Extended Menu

Item number

Item name

501

STILL TIMER

502

TAPE
PROTECTION
MODE FROM
SEARCH

Menu items in the 500s, relating to tape protection
Settings
Select the time delay from the tape transport stopping (either the "STOP" mode" or the
still playback mode in search mode) until the unit automatically switches to the tape
protection mode, in order to protect the rotary heads and the tape.

Item number

Item name

605

TCG REGEN
MODE

Menu items in the 600s, relating to the time code generator
Settings
Select the signal to be regenerated when the time code generator is in the regeneration
mode (i.e., when the PRESET/REGEN switch on the subsidiary control panel is set to
REGEN, or the unit is in automatic edit mode).

0.5S... 1M ..5M: Set the value in the range 0.5 seconds to 5 minutes.

TC&UB : Both the time code and user bits are regenerated.

Select the operation of the protection mode to protect the rotary heads and tape when in
the still playback mode in search (jog/shuttle) mode.

TC: Only the time code is regenerated.

STEP : Step forward at 1/30 normal speed at the time interval set with STILL TIMER.

UB: Only the user bits are regenerated.
607

STDBY: Switch to Standby OFF mode (the unit not on standby).

U-BIT BINARY
GROUP FLAG

Select the user bits to be used in the time code generated by the time code generator.
000 : Character set not specified.
001: 8-bit characters compliant with ISO 646 and ISO 2022.

Item number

Item name

601

VITC POSITION
SEL-1

010: Undefined.

Menu items in the 600s, relating to the time code generator
Settings

011: Undefined.
100: Undefined.

For DSR-2000

101: SMPTE 262M page/line multiplex system.

Select a line to insert the VITC in.

110: Undefined.

12H ... 16H ... 20H: Select any line from 12 to 20.
Note

111: Undefined.
610

You can insert the VITC signal in two places. To insert it in two places, set both items
601 and 602.
For DSR-2000P

REGEN
When editing with two DSR-2000/2000P units, if you use the control panel for editing
CONTROL MODE operation, select whether or not the time code is automatically regenerated.
AS&IN : In editing with this unit as the recorder, regardless of the setting of the INT/
EXT–PRESET/REGEN switch, in assemble and insert editing, the time code
generator regenerates according to the time code on the tape.

Select a line to insert the VITC in.

ASSEM: In editing with this unit as the recorder, regardless of the setting of the INT/
EXT–PRESET/REGEN switch, in assemble editing only, the time code generator
regenerates according to the time code on the tape.

9H ... 19H ... 22H: Select any line from 9 to 22.

MANU: Regardless of whether this unit is the recorder or player, the time code
generator operates in accordance with the PRESET/REGEN setting of the INT/EXT–
PRESET/REGEN switch.

Note
You can insert the VITC signal in two places. To insert it in two places, set both items
601 and 602.
602

VITC POSITION
SEL-2

FULL: Regardless of the REMOTE button setting, when any of the ASSEMBLE,
VIDEO, CH-1 to CH-4 and TC buttons is lit, the time code generator regenerates
according to the time code played back from the tape.

For DSR-2000
Select a line to insert the VITC in.
12H ... 18H ... 20H: Select any line from 12 to 20.

611

Note

TC OUTPUT
PHASE IN EE
MODE

Select the time code output mode for output from the TIME CODE OUT connector in EE mode.
MUTE : Mute the output.
THRU: Output the time code input to the TIME CODE IN connector as it is.

You can insert the VITC signal in two places. To insert it in two places, set both items
601 and 602.

V-IN: Output the time code with the same phase as the input video signal phase.

For DSR-2000P

V-OUT: Output the time code with the same phase as the output video signal phase.

Select a line to insert the VITC in.

612

TC OUTPUT
MUTE IN
SEARCH MODE

ON : Mute.

VITC OUTPUT

OFF: Do not mute.
Select the time code to be output as VITC.

Note
613

Setup Menu

You can insert the VITC signal in two places. To insert it in two places, set both items
601 and 602.

Select whether to mute the output from the TIME CODE OUT connector in search (jog/
shuttle) mode.

OFF: Do not output VITC.
TC: Output TC after converting it into VITC.
VITC : Output VITC.

DSR-2000/2000P

118

Chapter 6 Setup Menu

Chapter 6

Chapter 6 Setup Menu

9H ... 21H ... 22H: Select any line from 9 to 22.

Chapter 6 Setup Menu

119

DSR-2000/2000P

Extended Menu

Item number

Item name

Menu items in the 700s, relating to video control
Settings

701

SELECTION OF
VIDEO/SYNC
DELAY

An E-E video signal is output delayed with respect to the video input signal by the time for
video circuit processing. With this item, select whether or not to delay the sync signal
attached to the output video signal by an amount corresponding to the video signal delay.

Note

When you make settings for items 715 to 720, set the
PROCESS CONTROL switch on the subsidiary
control panel to MENU. When it is set to MENU, all
controls on the subsidiary control panel are disabled.

SYNC : Delay the sync signal by the corresponding amount before attaching it.
VIDEO: Attach a sync signal with the same timing as the input signal.
705

708

EDGE
Select whether to enable the edge subcarrier reducer (ESR).
SUBCARRIER
ON : Enable.
REDUCER MODE
OFF : Do not enable.
When playing back a composite signal, set this to ON.
CHROMA PHASE Select the phase rotation mode for chroma phase control.
ROTATION MODE The effect of this setting applies to the output levels of all of the composite video, S

Menu items in the 700s, relating to video control (continued)
Item number

Item name

723

INPUT VIDEO
Switching blanking on or off for the 335th line of the input video signal. Select the
BLANK
reference video signal to use.
(DSR-2000P only)
Sub-item
LINE335 THROUGH : Do not mute.
BLANK: Mute.

video, SDI and component video signals.
U/V : Select this setting when observing the unit's composite video output level using a
composite vectorscope.

710

729

PB/PR: Select this setting when observing the unit's component video output level using
a component vectorscope.
Select
the test signal to be output from the internal test signal generator.
INTERNAL VIDEO
SIGNAL
CB100 (DSR-2000P only): 100% color bar signal
GENERATOR
CB75: 75% color bar signal

CLOSED
CAPTION BLANK
(DSR-2000 only)

VIDEO SETUP
REFERENCE
(DSR-2000 only)
Sub-item
1 INPUT LEVEL

Select whether to mute the closed caption signal to be superimposed on the 1st and
2nd fields of the output video signal.

Sub-item
1 FIELD 1

Select whether to mute the closed caption signal to be superimposed on the 1st field of
the output video signal.
OFF : Do not mute.

BB: Black burst signal
713

Settings

2 FIELD 2

Default setting: CB100 (for DSR-2000P)/CB75 (for DSR-2000)
Select whether to remove the setup (7.5%) from the input analog video signals and
whether to add the setup (7.5%) to the output analog video signals.

ON: Mute.
Select whether to mute the closed caption signal to be superimposed on the 2nd field of
the output video signal.
OFF : Do not mute.
ON: Mute.

731

WIDE MODE

Whether to remove the setup from the input.

Determine whether to retain wide-screen aspect ratio information accompanying video
being recorded or played back.
AUTO : When video being recorded or played back is accompanied by wide-screen
aspect ratio information, retain the information.

0.0% : Do not remove.
7.5%: Remove.

ON: Whenever recording or playing back video, retain wide-screen aspect ratio
information.

2 OUT PUT LEVEL Whether to add the setup to the output.
0.0% : Do not add.

OFF: Ignore wide-screen aspect ration information.

7.5%: Add.
714

VIDEO ADJUST
RANGE

Select the variable range of the VIDEO and CHROMA knobs when the PROCESS
CONTROL switch on the subsidiary control panel is set to PANEL.
–3~+3 : –3 dB to +3 dB
WIDE: – ∞ to +3 dB

VIDEO GAIN
CONTROL

CHROMA PHASE Adjust the chroma phase.
CONTROL
00H to 80H to FFH
SETUP LEVEL
Adjust the setup level (DSR-2000)/black level (DSR-2000P).
(DSR-2000)/
00H to 200H to 3FFH
BLACK LEVEL
(DSR-2000P)
SYSTEM PHASE Adjust the subcarrier phase.
SC
00H to 3FFH
Chapter 6 Setup Menu

OFF: Do not adjust the audio playback speed.
ON : Adjust the audio playback speed.

802

DIGITAL AUDIO
MUTE IN
SHUTTLE MODE

Set the audio muting conditions during shuttle playback.
OFF : Not muted.
CUEUP: Muted during cue-up or preroll operations.

Adjust the chroma output level.
00H to 200H to 3FFH

Select whether to adjust the audio playback speed during slow playback.

FULL: Muted in shuttle mode.
807

AUDIO OUTPUT
PHASE

Select the output timing of an audio playback signal. The reference position corresponds
to a setting of 80H; when the setting is less than 80H, the output timing is advanced,
and when it is higher than 80H, the output timing is delayed. (80H = 128 samples =
approx. 2.7 ms, 1 sample = approx. 20 µs)
0 ... 80 ... FF : Setting in this range.

(Continued)

Chapter 6 Setup Menu

121

1-61

1-1. DSR-2000

717

120

DIGITAL JOG
SOUND

00H to 200H to 3FFH

CHROMA GAIN
CONTROL

720

801

Adjust the video output level.

716

718

Menu items in the 800s, relating to audio control
Settings

Setup Menu

715

Item name

Chapter 6

Chapter 6 Setup Menu

Items 715 to 720 : Settings for controlling the video processing system according to the menu settings.
Item number Item name
Settings

Item number

1-1. DSR-2000

1-62
Extended Menu

Menu items in the 800s, relating to audio controll (continued)
Settings

Item number

Item name

808

INTERNAL AUDIO Select the operation of the internal audio test signal generator.
SIGNAL
SILNC: Silent signal.
GENERATOR
1KHZ : 1-kHz, –20 dB FS sine wave signal.
When you select SG as the audio input in the input selection section of the upper control
panel, the audio test signal generated by the internal audio test signal generator is input.

811

AUDIO
REFERENCE
LEVEL

Select the audio reference level (headroom) for recording on tape.

–18dB (factory default for DSR-2000P)
AUDIO OUTPUT
LEVEL

To use the extended menu, set basic menu item 099
MENU GRADE to ENHAN beforehand.
In the extended menu, you can carry out the same
operations as in the basic menu except setting of subitems.

–12dB
–16dB
–20dB (factory default for DSR-2000)

812

Making settings for mixing an audio input
signal (extension menu item 819)

Extended Menu Operations

Select the analog audio output reference level.

Using extension menu item 819, you can mix audio
input signals, dub an audio input signal over a channel
previously recorded on the tape, or mix an audio input
signal with an audio channel recorded on the tape
(sound-on-sound).
To carry out the extension menu item 819 settings, use
the following procedure.

To set sub-items

6 3

Operate as follows.

+4dB : Set the analog output level of the signal at the reference level to +4 dBm.
0dB: Set the analog output level of the signal at the reference level to 0 dBm.

813

–6dB: Set the analog output level of the signal at the reference level to –6 dBm.
PEAK HOLD TIME Set the peak hold time for the audio level meter in the range of OFF (no peak hold) to
1.5 seconds in 0.1 second steps.

814

OVER RANGE
DISPLAY HOLD

Select whether to hold the audio level meter OVER display.
OFF : Do not hold.
ON: Hold.

818

AUDIO REC
MODE

Select the audio recording mode.

2CH : 2ch, 48 kHz mode
4CH: 4ch, 32 kHz mode

819

AUDIO INPUT
SOURCE
ARRANGE

For details, see the section “Making settings for mixing an audio input signal (extension
menu item 819)” (page 123).
AUDIO OUTPUT
Select the signals to be output from the AUDIO OUT CH-3 and AUDIO OUT CH-4
CH3/CH4 SELECT connectors.

820

Select the audio input signals to be mixed when the MIXING button is lit.

LINE : Output the audio channel-3 and audio channel-4 signals from the AUDIO OUT
CH-3 and AUDIO OUT CH-4 connectors as they are.
MONI: Output the monitor audio L-channel (CH-1) and monitor audio R-channel (CH-2)
signals from the AUDIO OUT CH-3 and AUDIO OUT CH-4 connectors, respectively.
821

AUDIO
ATTENUATE
WHEN DV TAPE
PLAYBACK

OFF: Attenuate.

Holding down the STOP button, turn the search
dial to select the desired sub-item.

Holding down the SEARCH button, turn the search
dial to change the value for the selected sub-item.

Press the STOP button.
The following displays appear in the display
section of the lower control panel and on a monitor
connected to this unit.
Chapter 6

Display section

Menu items in the 900s, relating to digital process
Item number

Item name

Settings

902

SYSTEM EE
MODE

Select the bypass E-E mode or system E-E mode.

Recording channel number

Setup Menu

Chapter 6 Setup Menu

Select extension menu item 819.
For details of selecting a menu item, see the section,
“Changing the currently displayed menu item” (page
111).

Turn the search dial to select the desired menu
item.
For information about how to select a menu item, see
the section “Changing the currently displayed menu
item” (page 111).

When playing back a tape recorded in consumer DV format, select whether to attenuate
the audio output level.
ON : Do not attenuate.

Input channel number

OFF : Bypass E-E (ordinary setting)
ON: System E-E
When this item is set to ON, the output delays 3 frames with respect to the input
(excluding the SDTI and i.LINK inputs/outputs).
Item number

Setting

DSR-2000/2000P

(Continued)

122

Chapter 6 Setup Menu

123

DSR-2000/2000P

Extended Menu

Monitor screen

Recording channel numbers

ITEM-819
AUDIO INPUT SOURCE
ARRANGE

Input channel numbers

in1 in2 in3 in4 tape
-------------------on
ch1: *on
on
ch2:
ch3:
on
on
ch4:

Cursor (shows the item selected for menu operations)

Holding down the STOP button, turn the search
dial to move the cursor to select a combination of
input and recording channels.

Holding down the SEARCH button, turn the
search dial to set the channel selection made in
step 3 to on or off.
To select an input channel for recording
For the selected recording channel, set the desired
input channel to on.

To enable the setting of extension menu item
819
Press the MIXING button in the upper control panel,
turning it on.
When the MIXING button is off, the settings of
extension menu item 819 are ignored, and the input
channels and recording channels are recorded one-toone. It is not possible to carry out mixing or channel
switching.

Chapter

Connections and
Settings

Note

When 2-channel mode (2CH) is selected for audio
recording (see extended menu item 818), the settings
made with this item for input channels 3 and 4 (in3 and
in4) as well as recording channels 3 and 4 (ch3 and
ch4) are invalid.
For example, when input channels 1 and 3 (in1 and
in3) are set to on for recording channel 1 (ch1), in 2CH
mode, only the signal from input channel 1 is recorded
on recording channel 1.

Reference Video Signals for Analog Signal Editing
In order to provide stable video and audio signals for
analog editing, it is necessary to input a reference
video signal synchronized with the video signal to the
REF. VIDEO IN connector and set the REF. VIDEO
IN 75 Ω termination switch to ON.

REF. VIDEO IN connector
and 75 Ω termination switch

To record, mixing more than one input signal
For the selected recording channel, set two or more
of the input channels to on. All of the input
channels set to on for each recording channel will
be mixed for that channel.
To switch on the sound-on-sound setting
In addition to the selected input channel(s), set
“tape” to “on.”
Chapter 6 Setup Menu

Repeat steps 3 and 4 for each of the recording
channels.

Press the SET button.

Chapter 7

Connections and Settings

125

1-63

1-1. DSR-2000

Chapter 6 Setup Menu

It is also possible to use an i.LINK-compatible
camcorder such as the DSR-500WS/500WSP as the
player and carry out cut editing.

Connections and

124

Using two DSR-2000/2000P units, each fitted with the
optional DSBK-190 board, as a pair of player and
recorder, you can configure a cut editing system.
You can use the same system also to digitally dub
signals in DVCAM format through an i.LINK interface
(see page 61).

Chapter 7
Settings

This saves the settings.

Connections for Cut Editing Using i.LINK Interface
(Optional DSBK-190 Required)

1
i.LINK(DSBK-190)

i.LINK(DSBK-190)

1-1. DSR-2000

1-64

Connections for Cut Editing Using i.LINK Interface (Optional DSBK-190
Required)

Connections for Digital Nonlinear Editing Using
SDTI (QSDI) Interface
This unit can be connected to an ES-7 EditStation to
configure a digital non-linear editing system. Using the
SDTI (QSDI) interface, you can transfer video, audio,
timecode, and other compressed data between this unit
and the EditStation.
The unit supports ClipLink functions, enabling index
pictures recorded on tape and ClipLink log data stored
in cassette memory to be transferred to the EditStation
in an instant.

The following is a connection diagram for digital nonlinear editing system in which this unit serves as the
recorder.
For connections of the EditStation’s peripheral devices (the
control panel, the disk unit, etc.) and the player, refer to
your ES-7 Operating Instructions.

For an overview of the ClipLink function, see the appendix
“ClipLink Guide” (page 147).
DSR-2000/2000P (recorder)

DSR-2000/2000P (player)

1 6-pin to 6-pin i.LINK cable (supplied with the DSBK-190)
1
SDTI(QSDI) INPUT

DSR-2000/2000P (recorder and player) settings

Control

Setting (recorder)

Setting (player)

REMOTE button

Unlit

Lit

i.LINK button

Lit

SDTI/i.LINK button
(input selection section)

i.LINK

SDTI(QSDI) OUTPUT

REF. VIDEO IN

BB OUT

1
1

QSDI OUTPUT
QSDI INPUT

ES-7

RECORDER

DSR-2000/2000P (recorder)
REMOTE-IN

1 75 Ω coaxial cable (not supplied)
2 RCC-5G 9-pin remote control cable (supplied)

DSR-2000/2000P (recorder) settings
Control

Setting

REMOTE button

Lit

9PIN button

Lit

SDTI/i.LINK button (input selection
section)

SDTI

REF.VIDEO IN 75Ω termination
switch

ON
Chapter 7
Settings

Chapter 7
Settings

Connections and

DSR-2000/2000P

126

Chapter 7 Connections and Settings

127

DSR-2000/2000P

Connections for Cut Editing Using SDI Interface
For a cut editing system using this unit together with a
DNW-A75/A75P Betacam SX VCR using an SDI
connection, the following figure shows an example of
the connections. In this example, the DNW-A75/A75P
is used as the recorder and this unit is used as the
player.

Connections for Preread Editing
For a preread editing system using two DSR-2000/
2000P units together with a video switcher, audio
mixer and editing control unit, the following figure
shows an example of connections.

DSR-2000/2000P (recorder)

DSR-2000/2000P (player)

DNW-A75/A75P (recorder)

REF. VIDEO
INPUT

SDI INPUT

REF.VIDEO OUT

SDI OUTPUT

DSR-2000/2000P
(player)

REF.VIDEO
IN

REF.VIDEO IN

REMOTE IN

VIDEO IN
VIDEO OUT

IN 2

1 75 Ω coaxial cable (not supplied)

DSR-2000/2000P (player) settings

Control

Setting

Control

Setting

REMOTE buttons

Unlit

REMOTE button

Lit

9PIN button

Lit

REF.VIDEO IN 75Ω
termination switch

AUDIO OUT
CH-1/CH-2

1
1
1

Video switcher (BVS-3200C,
DVS-2000C, etc.)

2 RCC-5G remote control cable (supplied)

DNW-A75/A75P (recorder) settings

IN 1
REF OUT
REF OUT

PGM OUT

VIDEO
OUT

AUDIO IN CH-1/CH-2
1

REMOTE-IN
REMOTE1-OUT(9P)

REMOTE-IN

AUDIO OUT CH-1/CH-2

RS-422A

REF OUT

1 75 Ω coaxial cable
(not supplied)

IN
Audio mixer (SRP-V200, etc.)

2 Cable with XLR connectors
(not supplied)

MASTER
OUT

REMOTE
4

3 RCC-5G 9-pin remote
control cable (supplied)

RS-422

GPI

RS-422

Editing control unit (BVE-2000, etc.)
4 RCC-5A/11A 15-pin
parallel control cable
(not supplied)

REF IN
RS-422

Chapter 7 Connections and Settings

129

1-65

1-1. DSR-2000

Chapter 7 Connections and Settings

Lit
Lit

Connections and

128

REMOTE button
9PIN button

Chapter 7
Settings

DSR-2000/2000P (recorder and player) settings
Control
Setting

When connecting an external editing control unit to
this unit and using this unit as a recorder, make the
following timecode settings on this unit and VCR
constant and DIP switch settings on the editing control
unit.

Timecode Settings on This Unit
Make the following time code settings for this unit.
Control

Connections for Component Analog Recording

For RM-450 (NTSC)
Set the VCR constants as follows.
• Left DIP switch
Switch No.

Setting

OFF —

—

OFF —

—

The following shows connections for a system in
which analog playback signals from another recorder
or player are recorded on the DSR-2000/2000P. In this
system, the video signals are analog component signals
and the audio signals are recorded from audio channels
1 and 2.

Switch No.

OFF —

OFF ON

OFF OFF ON

Setting

AUDIO IN
CH-1

TIME CODE IN

INT/EXT–PRESET/REGEN INT–PRESET (right position)
switch
FREE RUN/REC RUN switch FREE RUN

Note

In this case, the DSBK-170 Analog Component Iuput/
Output Board is required.

• Right DIP switch
Setting

AUDIO IN
CH-2

1
CH-1

For RM-450CE (PAL)
CH-2

Set the VCR constants as follows.
• Left DIP switch

Settings on Editing Control Units
Make the following settings according to the editor
model.

For FXE-100/120 (NTSC)
Set the VCR constants as follows.
Byte No. 1

Switch No.

Setting

OFF —

1-1. DSR-2000

1-66

Settings Required When Connecting an External
Editing Control Unit

—

OFF —

—

—
DSR-2000/2000P
(recorder)

Setting

—

OFF ON

OFF OFF ON

Videocassette recorder/
player such as
UVW-1600/1600P

COMPONENT
OUTPUT

• Right DIP switch
Switch No.

TC OUT
AUDIO
OUT

COMPONENT VIDEO IN
(Y,R−Y,B−Y)

0
1 Cable with XLR connectors
(not supplied)

2 75 Ω coaxial cable (not supplied)

For BVE-800
10 11 12 13 14 15

Setting 80 14 00 96 05 05 03 80 0A 08 FE 00 80 5A FF

Set the VCR constants as follows.
DSR-2000/2000P (recorder) settings

When using the DSR-2000 (NTSC)
• SW2

For FXE-100P/120P (PAL)
Set the VCR constants as follows.
Byte No. 1

For BVE-910/2000
Set the VCR constants as follows.
• When using the DSR-2000 (NTSC)
2

Block 2
4

10 11 12 13 14 15

Setting 80 14 00 96 05 05 03 80 0A 08 FE 00 80 5A FF

Block 2
4

Chapter 7 Connections and Settings

OFF ON

Y–R, B

—

AUDIO IN LEVEL/600Ω Normally, +4 dBm, 600Ω (HIGHswitch (connector panel) ON)

CH1,1/2 button and
CH2,3/4 button

• SW3
Switch No.

Setting

OFF —

OFF OFF

Unlit

ANALOG

When using the DSR-2000P (PAL)
• SW2
Switch No.

Setting

OFF ON

—

Switch No.

Setting

OFF OFF OFF ON

• SW3
3

—

OFF OFF

10 11 12 13 14 15

Setting 81 14 00 7D 05 05 02 80 0A 07 FE 00 80 4C FF

130

Setting

Connections and

DSR-2000/2000P

Connections and

• When using the DSR-2000P (PAL)
Byte No. Block 1

Chapter 7
Settings

Setting

REMOTE button
VIDEO IN button (input
selection section)

10 11 12 13 14 15

Setting 81 14 00 7D 05 05 02 80 0A 07 FE 00 80 4C FF

Byte No. Block 1

Switch No.

Control

For PVE-500
Use the factory settings as they are.

Chapter 7 Connections and Settings

131

DSR-2000/2000P

Connections for Two-Unit Synchronous Playback

Connections for Digitally Dubbing Signals in
DVCAM Format (Optional DSBK-190 Required When
Using i.LINK Interface)

The following shows connections for synchronous
playback using two DSR-2000/2000P units.
In the following, the controlling unit is referred to as
the recorder and the controlled unit as the player.

For information about how to carry out two-unit
synchronous playback, see the section “Synchronous
Playback” on page 59.

1
REF.VIDEO IN

REF.VIDEO OUT

Connecting two DSR-2000/2000P units using
the i.LINK interface (DSBK-190 i.LINK/DV
Input/Output Board)
Make the same connections and settings as described
in the section “Connections for Cut Editing Using
i.LINK Interface” (page 125).

You can use this unit to digitally dub signals in
DVCAM format automatically from the beginning of
the tape to the end, through an i.LINK or SDTI(QSDI)
interface.
For information about how to carry out digital dubbing, see
the section “Digitally Dubbing Signals in DVCAM Format”
(page 61).

Connecting two DSR-2000/2000P units using the SDTI(QSDI) interface

1
DSR-2000/2000P (player)

DSR-2000/2000P (recorder)

SDTI(QSDI) INPUT

REMOTE-IN

REMOTE-OUT

SDTI(QSDI) OUTPUT

1 75 Ω coaxial cable (not supplied)
2 RCC-5G 9-pin remote control cable (supplied)

DSR-2000/2000P (recorder) settings
Control

Setting

DSR-2000/2000P (player) settings
Control

Setting

REMOTE button

Unlit

REMOTE button

Lit

9PIN button
Setup menu item 004

Lit
ON (Synchronize.)
OFF (Do not
synchronize.)

9PIN button

Lit

Setup menu item 305
(When synchronizing,
synchronization accuracy)

ACCUR (±0 frame)
ROUGH (±1 frame)

REF. VIDEO IN 75 Ω
termination switch

DSR-2000/2000P (recorder)

DSR-2000/2000P (player)

REMOTE-OUT

REMOTE-IN
2
1 75 Ω coaxial cable (not supplied)
2 RCC-5G 9-pin remote control cable (supplied)

DSR-2000/2000P (recorder) settings

DSR-2000/2000P (player) settings

Control

Setting

Control

REMOTE button

Unlit

REMOTE button

Lit

9PIN button

Lit

9PIN button

Lit

SDTI/i.LINK button
(input selection section)

SDTI

Setting

Chapter 7 Connections and Settings

133

1-67

1-1. DSR-2000

Chapter 7 Connections and Settings

Connections and

132

Chapter 7
Settings

When connecting this unit with a DSR-60/60P/
80/80P/85/85P/1000-series/1000P-series unit
using the SDTI(QSDI) interface
Replace the DSR-2000/2000P (player) shown in the
above diagram with a DSR-60/60P/80/80P/85/85P/
1000-series/1000P-series unit and make the same
connections as shown above.
The SDTI(QSDI) interface connector of the DSR-60/
60P/80/80P/85/85P is marked “QSDI(OUTPUT)”.

1-1. DSR-2000

1-68

Chapter

Chapter 8

Maintenance and
Troubleshooting

Maintenance and Troubleshooting

Condensation
If you move the unit suddenly from a cold to warm
location, or if you use it in a very humid place,
moisture from the air may condense on the head drum.
This is called condensation, and if a tape is run in this
state, the tape may stick to the drum and can be easily
damaged. To lessen the risk of this occurring, this unit
is equipped with a condensation detection system.

If condensation occurs while the unit is
operating:
The alarm message “MOISTURE HAS BEEN
DETECTED.” appears on the monitor screen, and the
alarm message “HUMID!” in the display section of the
lower control panel. At the same time the unit ejects
the cassette automatically. If this happens, leave the
unit’s power on and wait until the alarm messages
disappear.
If the condensation alarm messages appear
immediately after powering on:
Leave the unit powered on and wait until the alarm
messages disappear. You cannot load a cassette into
the unit while the alarm messages are being displayed
Once the alarm messages disappear, the unit is ready
for use.

Head Cleaning
Always use the DVM12CL (mini-size) or DV12CL
(standard size) Cleaning Cassette to clean the video
and audio heads. You can run the cleaning cassette for
10 seconds per cleaning operation. Follow the
instructions for the cleaning cassette, as inappropriate
use of the cleaning cassette can damage the heads.

To clean the heads
Insert the cleaning cassette. This automatically starts
cleaning. You cannot operate any tape transport
control buttons other than the EJECT button during the
cleaning operation.
After about 10 seconds, the cleaning cassette will be
automatically ejected.

DSR-2000/2000P

Chapter 8 Maintenance and Troubleshooting

135

DSR-2000/2000P

Periodic Maintenance

Troubleshooting
If an alarm message appears in the display section or
on the video monitor connected to this unit, or if the

The digital hours meter can provide seven items of
information about the operational history of the unit.
The information can be displayed in the display
section of the lower control panel and also, by text
superimposition, on the monitor connected to the unit.
Use the information as a guide in scheduling periodic
maintenance.

Press the MENU button, then turn the search dial to
display the required item in the display section and on
the monitor connected to the unit.
COUNTER SEL button

H01: OPERATION mode
Displays the total number of hours the unit has been
powered on in units of 1 hour.

H03: TAPE RUNNING mode
Displays the total number of hours the unit has been in
fast forward, rewind, playback, search, recording or
editing (except for stop and still) mode in units of 1
hour.
H04: THREADING mode
Display the total number of times tape has been
threaded in the unit.
H12: DRUM RUNNING mode (resettable)
Same as H02 except that the count is resettable.
This can be used as a guide in determining when to
replace the drum.
H13: TAPE RUNNING mode (resettable)
Same as H03 except that the count is resettable.
This can be used as a guide in determining when to
replace such components as stationary heads and pinch
roller.
H14: THREADING mode (resettable)
Same as H04 except that the count is resettable.
This can be used as a guide in determining when to
replace, for example, the threading motor.

Chapter 8 Maintenance and Troubleshooting

Cause

Remedy

The KEY INHIBIT switch on the
subsidiary control panel is set to ON.

Set the KEY INHIBIT switch on the subsidiary
control panel to OFF.

The CONTROL PANEL switch on the
subsidiary control panel is set to EXT.

• Set the CONTROL PANEL switch on the
subsidiary control panel to INT.
• Set extended menu item 117 to PARA.

The REMOTE button is lit and menu item Turn off the REMOTE button and, on the
006 (LOCAL FUNCTION ENABLE) is set subsidiary control panel, set the KEY INHIBIT
to ST&EJ or DIS.a)
switch and CONTROL PANEL switch to OFF and
INT, respectively.
No cassette is loaded.a)

Insert a cassette.

Symptom

Cause

Remedy

Recording is not possible.

The cassette’s REC/SAVE switch is set
to SAVE.a)

Set the REC/SAVE switch to REC, or use
another cassette.

The REC INHIBIT switch on the
subsidiary control panel is set to ON.

Set the REC INHIBIT switch on the subsidiary
control panel to OFF.

Tape problems
Search dial
SET button
MENU button

To exit from the hours meter
Press the MENU button or SET button.
To jump to H01
Press the MENU button, then the COUNTER SEL
button.
Every time you press the COUNTER SEL button,
menu item H01 or B01 is recalled alternately.

The NOT EDITABLE indication The recording mode selected on this unit • Set the unit for the same recording mode as with
appears in the display section. does not coincide with that of the loaded
the tape.
tape.a)
• When your current purpose is recording, you
can use the tape currently loaded in the unit.
The recording format of the currently
• You can use the currently loaded tape as a
loaded tape is DV or DVCPRO.
source tape for playback and editing.
• You cannot use the tape as a recording tape for
editing.
Time data problems
Symptom

Cause

Remedy

Cannot set the time data to an
optional initial value.

The PRESET/REGEN switch on the
subsidiary control panel is set to
REGEN.a)

Set the PRESET/REGEN switch on the
subsidiary control panel to PRESET.

The tape is running, but the
time data does not appear in
the display section.

The counter value is selected as the time Press the COUNTER SEL button to light the TC
data for display (the COUNTER indicator (time code) or U-BIT (user bits) indicator in the
is lit in the display section).a)
display section (the counter value cannot be
preset).
The HOLD button has been pressed.
Press the button once again to exit the time code
preset mode.
The U-BIT indicator is lit in the display
section.a)

Press the COUNTER SEL button to light the
COUNTER (counter value) or TC (time code)
indicator in the display section.

a) In these states, alarm messages appear in the display section and on the monitor screen.

Chapter 8 Maintenance and Troubleshooting

137

1-69

1-1. DSR-2000

136

Symptom
The unit’s control buttons do
not work.

The unit’s transport control
buttons (PLAY, F FWD, REW,
etc.) do not work.

Display modes of the digital hours meter

H02: DRUM RUNNING mode
Displays the total number of hours the drum has run
with tape threaded in units of 1 hour.

Operation problems

Display section

For periodic maintenance, cousult your Sony dearler.

unit appears to be malfunctioning, please check the
following before contacting your Sony dealer.

Maintenance and Troubleshooting

To display the hours meter

Chapter 8

Digital hours meter

1-1. DSR-2000

1-70
Troubleshooting

Input problems

Error Messages

Symptom

Cause

Remedy

It is not possible to record an
SDTI signal.

No SDTI signal is input to the unit.a)

Connect an SDTI (QSDI) signal to the SDTI
(QSDI) INPUT connector.

Monitor problems
Cause

Remedy

Data is not superimposed on
the monitor screen.

The CHARACTER switch on the
subsidiary control panel is set to OFF.

Set the CHARACTER switch on the subsidiary
control panel to ON.

ERROR

The monitor is not connected to the
Connect the monitor to the VIDEO OUT 3
VIDEO OUT 3 (SUPER) or SDI OUTPUT (SUPER) or SDI OUTPUT 3 (SUPER) connector.
3 (SUPER) connector of this unit.
(You must make this connection to display any
type of text on the monitor.)
The image on the monitor
screen is too bright.

The 75 Ω termination switch for video
input on the monitor is in the OFF
position or a 75 Ω terminator is not fitted
to its video input connector.

The image on the monitor
screen is too dark.

In a video signal loop-through connection Set the 75 Ω termination switches to OFF on all
of video monitors, 75 Ω termination
monitors other than the loop-end monitor .
switches for video input on monitors
other than the loop-end monitor are in
the ON position.

The image is too dark when
recording a composite video
signal.

Note

To display error messages on the monitor screen, set
the CHARACTER switch on the subsidiary control
panel to ON.

Maintenance and Troubleshooting

Symptom

This unit is provided with a self-diagnostic function
that detects internal abnormalities. When it detects an
abnormality, it outputs an error message to the monitor
connected to the unit and indicates an error code in the
display section of the unit.

AN ERROR HAS BEEN
DETECTED. INFORM SERVICE
OF FOLLOWING CODE:
02-603

Set the 75 Ω termination switch to ON or connect
a terminator.

PRESS EJECT KEY
TO EJECT TAPE.

Error message
Error code
Direction

Error code

Error02-603
Monitor screen

Display section

If an error message appears, follow the direction
indicated under the message on the monitor screen.

Audio problems
Symptom

Cause

Turning the REC controls does The REC controls are pushed in.
not change the audio input
levels.
Turning the PB controls does
The PB controls are pushed in.
not change the playback audio
output levels.

Remedy
Pull out the REC controls.

Pull out the PB controls.

Alarm Messages
An alarm message , for example, like the one shown
below may appear on the monitor screen during
operation of the unit.
ALARM
REMOTE MODE IS SELECTED

Cause of alarm

SET REMOTE/LOCAL SWITCH
TO LOCAL

Direction

REMOTE!
Monitor screen

If an alarm message appears, follow the direction
indicated under the message on the monitor screen.

Display section

To display alarm messages on the monitor screen, set
the CHARACTER switch on the subsidiary control
panel to ON, and setup menu item 016 (ALARM) to
ON or LIMIT.
For details of setup menu operations, see Chapter 6 “Setup
Menu” (page 107).

DSR-2000/2000P

138

Chapter 8 Maintenance and Troubleshooting

Chapter 8

a) In this state, an alarm message appears in the display section and on the monitor screen.

139

DSR-2000/2000P

Troubleshooting

Alarm messages and associated directions (Continued)

Alarm messages and associated directions
Alarm message on monitor screen

Direction

Cause

Alarm message in the
diaplay section

VIN NON-STD

A non-standard ref. signal is being used for
REF. VIDEO.

Use a standard signal.

REF NON-STD

Abnormal settings selected in setup menu.

Correct the setup menu settings. Contact your
Sony dealer if this alarm message appears again
after making corrections.

ILL. SETUP

Alarm message in the
display section

Remote mode is selected.

Turn off the REMOTE button.

REMOTE!

Tape cannot be replayed.

Use a tape recorded in 525/60 format. (For DSR2000)

625/50 Tape (For DSR2000)

Use a tape recorded in 625/50 format. (For DSR2000P)

525/60 Tape (For DSR2000P)

Tape end has been detected.

Use a new cleaning tape.

Tape end!

Tape not editable.

Use a tape recorded in DVCAM format.

Not DVCAM!
625/50 Tape (For DSR2000)

Audio mixing mode cannot be changed
during recording.

—

REC mode!

Use a tape recorded in 525/60 format. (For DSR2000)

Audio not editable on this tape.

Use a tape recorded in 2-channel (48 kHz) or
4-channel (32 kHz) mode.

2CH/32kHz!

Use a tape recorded in 625/50 format. (For DSR2000P)

525/60 Tape (For DSR2000P)

Audio REC mode selection different from
audio on tape.

Use a tape having audio signals recorded in locked
mode.
Select the same audio recording mode as that of
the tape.

Fs 44.1kHz!
UNLOCK mode
A mode err

Audio REC (recording) mode cannot be
changed during recording.

—

REC mode!

Cassette adaptor not usable.

Use a tape without cassette adaptor.

Adaptor!

Counter mode is selected.

Use the COUNTER SEL button to light the TC or U- CNT mode!
BIT indicator in the display section.

Input selection cannot be changed in REC
(recording) mode.

—

Unknown Sig
625/50 sig! (For DSR2000)
525/60 sig! (For DSR2000P)
No INPUT!

Input signal is 625/50. (For DSR-2000)

—
—

Input video is not detected.

Check the INPUT VIDEO indication in the input
selection/audio mode display section and supply an
appropriate video signal.

Input video signal does not synchronize with Use a common reference signal or connect the
REF. VIDEO signal.
recorder REF. VIDEO OUT connector to the player
REF. VIDEO IN connector.

Use a DVCAM/DV ME tape.

REC INHI.!

Use DVCAM/DV/DVCPRO (25) tape.

ILL. Tape!

TC EXTERNAL is selected.

Set the INT/EXT switch on the subsidiary contol
panel to INT.

TC EXT!

TCG REGEN mode is selected.

Set the PRESET/REGEN switch on the subsidiary
control panel to PRESET.

REGEN mode!

TCG RUN mode is set to REC RUN.

Set the FREE RUN/REC RUN switch on the
subsidiary control panel to FREE RUN.

REC RUN!

REC mode!

Input signal does not conform to DVCAM/DV —
format.

Input signal is 525/60. (For DSR-2000P)

Tape not recordable.
Tape not usable.

Maintenance and Troubleshooting

The tape will automatically be ejected after cleaning Cleaning Tp
is completed.
Use a standard signal.

Direction

Cause

Chapter 8

A cleaning tape has been inserted.
A non-standard signal is being used for
input video.

Alarm message on monitor screen

ILL. REF!

Note
When connecting the recorder REF. VIDEO OUT
connector to the player REF. VIDEO IN connector,
set extended menu item 308 to N-STD.
Key inhibit mode is selected.

Set the KEY INHIBIT switch on the subsidiary
control panel to OFF.

KEY INHI.

Moisture has been detected.

Keep the power on and wait until this alarm
message disappears.

HUMID!

No cassette in VTR.

Load a cassette.

No Cass.!

Rec inhibit mode is selected.

Set the REC INHIBIT switch on the subsidiary
control panel to OFF.
Set the REC/SAVE switch on the cassette to REC.

REC INHI.!

140

REC INHI.!

(Continued)
Chapter 8 Maintenance and Troubleshooting

Chapter 8 Maintenance and Troubleshooting

141

1-71

1-1. DSR-2000

Record inhibit plug on the cassette is set to
inhibit.

1-1. DSR-2000

1-72

Appendixes
Appendixes

Notes on Use
Operation and storage locations
Avoid operation or storage in any of the following
places.
• Location subject to extremes of temperature
(operating temperature range 5°C to 40°C (41°F to
104°F))
• Location subject to direct sunlight for long periods, or
close to heating appliances (Note that the interior of a
car left in summer with the windows closed can
exceed 50°C (122°F).)
• Damp or dusty places
• Location subject to severe vibrations
• Location near equipment generating strong
electromagnetic emissions
• Location near transmitting stations generating strong
radio waves
Operate the unit in a horizontal position
This unit is designed to be operated in a horizontal
position. Do not operate it on its side, or tilted through
an excessive angle (exceeding 20°).

Avoid violent impacts
Dropping the unit, or otherwise imparting a violent
shock to it, is likely to cause it to malfunction.
Do not obstruct ventilation openings
To prevent the unit from overheating, do not obstruct
ventilation openings, by for example wrapping the unit
in a cloth while it is in operation.
Care
If the casing or panel is dirty, wipe it gently with a soft
dry cloth. In the event of extreme dirt, use a cloth
steeped in a natural detergent to remove the dirt, then
wipe with a dry cloth. Applying alcohol, thinners,
insecticides, or other volatile solvents may result in
deforming the casing or damaging the finish.
Shipping
Pack the unit in its original carton or equivalent
packing, and take care not to impart violent shocks in
transit.
When transporting the unit, set the reel position to that
for mini size cassettes.

DSR-2000/2000P

Appendixes

143

DSR-2000/2000P

Specifications
Tape transport control system

Processor adjustment range

Power requirements
100 to 240 VAC, 50/60 Hz
Power consumption
120 W
Peak inrush current
(1) Power ON, current probe method: 65A (240V)
(2) Hot switching inrush current, measured in
accordance with European standard
EN55103-1: 15A (230V)
Operating temperature
5˚C to 40˚C (41˚F to 104˚F)
Storage temperature
–20˚C to +60˚C (–4˚F to +140˚F)
Humidity
Maximum 80% (Operating)
Maximum 90% (Storage)
Mass
About 18 kg (39 lb 10 oz)
Dimensions (w/h/d)
427 × 174.5 × 495.5 mm
(16 7/8 × 6 7/8 × 19 5/8 inches)

Tape speed

Video level
±3 dB/–∞ to 3 dB selectable
Chroma level
±3 dB/–∞ to 3 dB selectable
Setup/Black level
±30 IRE (±210 mV)
Chroma phase
±30˚
Y/C delay
±100 ns
System phase
Sync: ±3µs
SC: ±180°

28.193 mm/s (DSR-2000)
28.221 mm/s (DSR-2000P)
Recording/playback time
Using PDV-184ME standard-size
cassette: 184 minutes or less
Using PDVM-40ME mini-size
cassette: 40 minutes or less
Fast forward/rewind time
Using PDV-184ME standard-size
cassette: 3 minutes or less
Using PDVM-40ME mini-size
cassette: 1 minute or less
Search speed
Up to 60 times normal in both
directions

Video performance

52.5 (2 1/8)

174.5
(6 7/8)

424 (16 3/4)
427 (16 7/8)

19.7 (2 5/32)

495.5 (19 5/8)

400 (15 3/4)

4.8 (7/32)

Band width

27.5 (1 1/8)

16.5 (21/32)

372 (14 3/4)

S/N

Y/C delay
K-factor

Composite (DSR-2000):
30 Hz to 4.2 MHz ±1.0 dB (Y)
Composite (DSR-2000P):
25 Hz to 4.8 MHz ±1.0 dB (Y)
S-Video (DSR-2000):
30 Hz to 5.0 MHz ±1.0dB (Y),
5.75 MHz +0/–3.0 dB (Y) (TM)
S-Video (DSR-2000P):
25 Hz to 5.0 MHz ±1.0dB (Y),
5.5 MHz +1.0/–2.0 dB (Y),
5.75 MHz +0/–3.0 dB (Y) (TM)
Component (DSR-2000):
30 Hz to 5.0 MHz ±1.0 dB (Y),
5.75 MHz +0/–3.0 dB (Y) (TM),
30 Hz to 1.3 MHz ±1.0 dB (C),
1.5 MHz +0/–5.0 dB (C)
Component (DSR-2000P):
25 Hz to 5.0 MHz ±1.0 dB (Y),
5.5 MHz +1.0/–2.0 dB (Y),
5.75 MHz +1.0/–3.0 dB (Y) (TM),
25 Hz to 1.5 MHz ±1.0 dB (C),
2.0 MHz +1.0/–2.0 dB (C)
Composite I/O (Y):
53 dB or more
S-Video I/O (Y): 55 dB or more
Component I/O (Y):
55 dB or more
30 ns or less
2.0% or less (K2T, KPB)

Audio performance
Frequency response
2 ch (48 kHz/16 bit):
20 Hz to 20 kHz +0.5/–1.0 dB
4 ch (32 kHz/12 bit):
20 Hz to 14.5 kHz +0.5/–1.0 dB
Dynamic range
90 dB or more (2CH, 48 kHz)
Distortion
0.05% or less (2CH, 48 kHz)

COMPONENT VIDEO IN Y/R–Y/B–Y
BNC type ×3, component video
Y: 1.0 Vp-p, 75 Ω, sync negative
R–Y: 0.7 Vp-p, 75 Ω (75% for
DSR -2000 or 100% for DSR2000P)
B–Y: 0.7Vp-p, 75 Ω (75% for
DSR -2000 or 100% for DSR2000P)
Analog audio input
AUDIO IN
XLR 3-pin (female) ×4,
–6/0/+4 dBu, 600 Ω ON/OFF/–60
dBu, high impedance, balanced
Digital audio input
DIGITAL AUDIO (AES/EBU) IN CH-1/2, CH-3/4
BNC×2, complying with AES-3id1995

Appendixes

General

Timecode input
TIME CODE IN BNC type ×1, SMPTE (DSR2000)/EBU (DSR-2000P)
0.5 to 18 Vp-p, 3.3 kΩ, unbalanced

Input connectors
Digital input
i.LINk (When using DSBK-190 i.LINK/DV Input/
Output Board)
6-pin IEEE1394 connector ×1
SDTI (QSDI) INPUT
BNC type ×1, SDTI (QSDI) format
(270Mbps), SMPTE 305M/322M
SDI INPUT
BNC type ×2 (active-through),
SMPTE 259M (DSR-2000)/ITU-R
BT.656 (DSR-2000P), SDI format
(270Mbps)
Analog video input
VIDEO IN
BNC type ×2 (loop-through),
composite, 1.0 Vp-p, 75 Ω, sync
negative
REF. VIDEO IN BNC type ×2 (loop-through), black
burst, 0.286 Vp-p (DSR-2000) or
0.3 Vp-p (DSR-2000P), 75 Ω, sync
negative
S VIDEO IN
DIN 4-pin ×1
Y: 1.0 Vp-p, 75 Ω, sync negative
C: 0.286 Vp-p (DSR-2000) or
0.3 Vp-p (DSR-2000P), 75 Ω
(burst level)

Output connectors
Digital output
i.LINK (When using DSBK-190 i.LINK/DV Input/
Output Board)
6-pin IEEE1394 connector ×1
SDTI (QSDI) OUTPUT
BNC type ×1, SDTI (QSDI) format
(270Mbps), SMPTE 305M/322M
SDI OUTPUT 1, 2, 3 (SUPER)
BNC type ×3, SMPTE 259M
(DSR-2000)/ITU-R BT.656 (DSR2000P), SDI format (270Mbps)
SDTI-CP OUTPUT (When using DSBK-210)
BNC type ×3
SMPTE 305M, 326M
Analog video output
VIDEO OUT 1, 2, 3 (SUPER)
BNC type ×3, composite, 1.0 Vp-p,
75 Ω, sync negative
REF. VIDEO OUT
BNC type ×1, composite sync,
0.286 Vp-p (DSR-2000) or 0.3 Vpp (DSR-2000P), 75 Ω, sync
negative (with burst)

Unit: mm (inches)

Appendixes

145

1-73

1-1. DSR-2000

144

Appendixes

Analog audio output
AUDIO OUT
XLR 3-pin (male) ×4, +4/0/–6 dBu
(selectable by menu setting),
600 Ω loaded, low impedance,
balanced
MONITOR AUDIO
Phono jack ×1, –11 dBu, 47 kΩ
load, unbalanced
Digital audio output
DIGITAL AUDIO (AES/EBU) OUT CH-1/2, CH-3/4
BNC×2, complying with AES-3id1995
Headphone output
HEADPHONES Stereo phone jack ×1, –∞ to
–13 dBu, 8 Ω, unbalanced
Timecode output
TIME CODE OUT
BNC type ×1, SMPTE (DSR2000)/EBU (DSR-2000P)
2.2 Vp-p±3.0 dB, 600 Ω,
unbalanced, (when 75 Ω
terminated)

REMOTE-IN

REMOTE-OUT

D-sub 9-pin, female, for connection
of another DSR-2000/2000P unit or
other editing controller, complying
with RS-422A
D-sub 9-pin, female, for loopthrough output of signals from the
REMOTE-IN connector

What Is ClipLink?
The ClipLinkTM function greatly improves the
efficiency of the video production process as a whole
by recording various editing-related data on tape when
shooting. As such, ClipLink is a revolutionary
function that transcends the conventional separation of
shooting and editing.

Accessories supplied
AC power cord (1)
Operating Instructions (1)
RCC-5G 9-pin remote control cable (1)

How ClipLink Changes Video Production
Techniques

Accessories not supplied

The following describes various ways in which
ClipLink1) video production differs from conventional
video production.

DSBK-210 SDTI-CP Output Board
DSBK-190 i. LINK/DV Input/Output Board
RCC-5G 9-pin Remote Control Cable, 5 m (16 ft) long
DSBK-200 Control Panel
RMM-130 Rack Mount Kit
PDV-64ME/94ME/124ME/184ME Digital Video
Cassette (standard size)
PDVM-12ME/22ME/32ME/40ME Digital Video
Cassette (mini-size)
DV12CL Cleaning Cassette (standard size)
DVM12CL Cleaning Cassette (mini-size)

Recording of ClipLink log data lightens the
shooting workload
When you start shooting a scene, ClipLink log data
such as the scene number and time code data are
automatically recorded into the cassette memory. This
eliminates the need for a conventional “shot list”
compiled by someone using a stopwatch, clipboard
and pencil. You can also designate unwanted scenes
as “NG” (no good) and automatically skip all “NG”
scenes when editing.

Design and specifications are subject to change
without notice.

Next, begin rough editing by viewing the Index
Pictures on the EditStation’s GUI display and
rearranging them as you wish. This eliminates the
difficult work of matching up a handwritten shot list
with recorded scenes. After you have completed this
rough editing, you can then transfer only the
recordings needed for your video program.
High-speed transfer of recordings
It is also possible to transfer the editing material itself
between the DSR-85/85P and ES-7 at four times
normal speed. In other words, the transfer can be
carried out in one fourth of the real time duration. It is
of course possible to carry out a transfer at four times
normal speed when backing up video and audio data
recorded on the disk drive to the DSR-85/85P, or in the
opposite direction when loading data backed up on the
DSR-85/85P to the disk drive. Thus the time required
is much shorter than with conventional equipment (for
which, for example, transferring a 40-minute segment
of video takes 40 minutes).
Note

To transfer digital signals (video, audio and time code)
recorded on a tape on this unit from the DSR-85/85P
to the ES-7 at four times normal speed requires a
continuous recorded section of about 40 seconds
before the IN point on the recorded tape.

Recorded Index Pictures drastically cut
editing time
The ClipLink function also features Index
Pictures a time-saving tool for rough editing. Each
Index Picture is a compressed image taken from the
start of each scene, which is recorded onto the tape as
a still picture. When editing, begin by transferring
only the Index Pictures and the ClipLink log data to
the EditStation’s hard disk. You can also transfer OK
scenes only (“NG” scenes are skipped).

Control connectors
VIDEO CONTROL
D-sub 15-pin, male, for connection
of optional UVR-60/60P or BVR50/50P
CONTROL PANEL
D-sub 15-pin, female, for
connection of optional DSBK-200

DSR-2000/2000P

146

Appendixes

..........................................................................................................................................................................................................
1) The ClipLink system is a video production system which
uses the cassette memory function.

Appendixes

147

Appendixes

DIN 4-pin ×1
Y: 1.0 Vp-p, 75 Ω, sync negative
C: 0.286 Vp-p (DSR-2000) or
0.3 Vp-p (DSR-2000P), 75 Ω
(burst level)
COMPONENT VIDEO OUT Y/R–Y/B–Y
BNC type ×3, component video
Y: 1.0 Vp-p, 75 Ω, sync negative
R–Y: 0.7 Vp-p, 75 Ω (75% for
DSR-2000 or 100% for DSR2000P)
B–Y: 0.7Vp-p, 75 Ω (75% for
DSR-2000 or 100% for DSR2000P)
S VIDEO OUT

1-1. DSR-2000

1-74

ClipLinkTM Guide

Specifications

DSR-2000/2000P

ClipLink Guide

Example System Configuration and Operation Flow

Data Generated When Shooting

The following illustration shows an example system
configuration for using the ClipLink function and a
typical ClipLink operation flow.

The following describes the kinds of data that is
generated when using the ClipLink function.

Index Pictures

DVCAM standard cassette or DVCAM mini cassette
Index Pictures: recorded on
tape
ClipLink log data: recorded in
cassette memory

Index Picture
0
(PAL) NTSC
(72)

Scene 2

ClipLink log data recorded onto DVCAM
cassettes links shooting and editing operations.

ClipLink log data tranfer
ES-7 EditStation™
non-linear editing
system
DSR-2000/85/1800/1600a)
(or DSR-2000P/85P/1800P/
1600Pa)) Digital
Videocassette Recorder

Scene 3

DVCAM camcorder’s
internal memory

Scene n

180

270

360

450

540

630

(144)

120

(216)

180

(288)

240

(360)

300

(432)

360

(504)

420

720 dots
After shooting, the Index
Pictures in the internal
memory are recorded onto the
video tape.

Up to 32 Index Pictures can be recorded onto the tape
space normally occupied by one frame, as shown
below.

Index Pictures
Video output (QSDI)
ClipLink log data

Tape
Scene 1

Appendixes

DVCAM
camcorder (DSR130/130P/300/
300P/500WS/
500WSP)

When shooting, a single-frame image from the Mark
IN point at the start of each scene is recorded as a still
picture into the DSR-1/1P’s internal memory. These
images are called “Index Pictures”. When you finish
shooting, the Index Pictures from all scenes are
recorded onto the tape after the last scene.

480 lines (NTSC) or 576 lines (PAL)

Shooting

Seven frame spaces are reserved at the end of the last
scene as a recording area for Index Pictures. (A
cassette with 16 Kbits of cassette memory can record
up to 198 Index Pictures, and a cassette with 4 Kbits of
cassette memory can record up to 45 Index Pictures.)

RS-422A interface

ClipLink log data
Editing
ES-7 EditStation™
non-linear editing
system
DSR-2000/85b)/1800/1600a)
(or DSR-2000P/85Pb)/1800P/
1600Pa)) Digital
Videocassette Recorder

ClipLink log data can be recorded automatically or
manually into the cassette memory for use as a
ClipLink log data

Description

Reel number (cassette number)

Data (maximum length: 8 digits) consisting of alphanumeric characters and/or
symbols (This is left blank at shipping.)
A three-digit number from 001 to 198 (starts at 001 and is automatically incremented
with each scene).
This cannot be changed (set to “1” at shipping).

Scene number
Actual AV data
QSDI input/output

Take number

Indicates the OK/NG status of a particular scene. (In the OK case, nothing is
recorded.)

Mark IN/OUT point time codes

These are the time codes that indicate the Mark IN and Mark OUT points for each
scene (HH:MM:SS). These time codes are recorded when the camera has been set to
MARK mode.
The frame digit is incremented at each Mark IN point and is decremented at each Mark
OUT point. (For details, see “Time codes recorded for Mark IN/OUT points” on page
151.)

Cue point time code

This is the time code that indicates the cue points (valid up to the frame digit). This
time code is recorded when the camera has been set to CUE mode. When in this
mode, the time codes at the start and end of a recording (the Rec IN and Rec OUT
time codes) are automatically recorded as Mark IN/OUT points.

Appendixes

149

1-75

1-1. DSR-2000

OK/NG

a) The DSR-1600/1600P is a videocassette player.
b) Between the DSR-85/85P and ES-7, quadruple transfer is possible through the QSDI.

148

convenient alternative to the conventional “shot list”.
ClipLink log data includes the following items.

1-1. DSR-2000

1-76
ClipLink Guide

How to record ClipLink log data

Time codes recorded for Mark IN/OUT points

The following describes how to record the various
ClipLink log data items.

Index Picture 1

Start
recording

End
recording
Scene 1
Take 1

Scene 2
Take 1

Mark IN
(manual
recording)

DSR-2000/2000P

150

Appendixes

Mark OUT
(manual
recording)

Cue point
time code
(manual
recording)

12:23:15:10

Mark OUT
(or Rec OUT)

12:34:20:20

12:39:24:23

End
recording
Frame digit
incremented

Scene 1
Take 1

Rec IN
(automatic
recording)

Index Picture 2

Mark IN
(or Rec IN)
Actual time code

Start
recording

Mark IN/OUT points time codes
This data is especially useful when shooting a video
program for which a scenario has been created.
Set the camera to MARK mode before you start
shooting. While shooting, each time you press the
camera’s TAKE button, Mark IN and Mark OUT time
codes are recorded alternately.

Index Picture 1

There is a gap between actual time codes and Mark IN/
OUT time codes recorded in the cassette memory, as
shown in the figure below. The frame digit is
incremented at each Mark IN point and is decremented
at each Mark OUT point.

Appendixes

OK/NG status
To designate a scene as “NG”, press the NG button on
the camera while shooting the scene or at any time
before you begin shooting the next scene.
All scenes that do not receive an “NG” designation are
recorded as “OK” scenes.
(When you exit the VTR recording mode, changing the
OK/NG status is no longer possible.)

Cue point time codes
This type of data is especially useful when shooting
scenes that may contain unexpected events, such as
when shooting for sports coverage or documentaries.
Set the camera to CUE mode before you start to
record. While recording, each time you press the
camera’s TAKE button, the current time code is
recorded as a cue point time code.

Time code
recorded in the
cassette memory
Rec OUT
(automatic
Cue point recording)
time code
(manual
recording)

12:23:16

Frame digit
decremented
Cue

12:34:20:20

12:39:24

(The Index
Picture is the
image around
12:23:15:10.)

Recording capacity for Mark IN/OUT time
codes and Cue point time codes
When in MARK mode, up to 198 pairs of Mark IN and
Mark OUT points can be recorded (if using a cassette
with 16 Kbits of cassette memory).
When in CUE mode, up to 396 time codes points
(including all cue point time codes and all Mark (Rec)
IN and Mark (Rec) OUT time codes) can be recorded
(if using a cassette with 16 Kbits of cassette memory).

Appendixes

151

DSR-2000/2000P

Glossary
Glossary
AES/EBU format
A unified format for digital audio signals.
It allows a single XLR connector to carry
the signals for two channels.
Assemble editing
Editing in which new video/audio is added
in sequence to the end of existing recorded
video/audio. See also “Insert editing”.

B–Y signal
One of the color difference signals, the B
(blue) signal minus Y (luminance) signal.
C signal
See “Chrominance signal”.
Capstan
A drive mechanism that moves the tape at
a specified speed regardless of the
direction (forward or reverse).
Chrominance signal
A signal which carries information about
hue and saturation. Also called “C signal”.
Condensation
Moisture which condensed on tape
transport mechanisms. If there is
condensation on the head drum, tape sticks
to drum and the VCR may malfunction.
Component video signal
A signal that consists of a luminance
signal (Y) and two chrominance signals
(R–Y, B–Y).
Composite video signal
A signal that consists of video, sync and
color burst signals.
Digital VCR
On a digital VCR, video and audio signals
are recorded on magnetic tape and, unlike
on an analog VCR, can be played back
without any quality deterioration.

152

Appendixes

Emphasis
The signal is emphasized at high
frequencies. During playback, it is deemphasized. This suppresses noise
without affecting the original signal.
External lock/Gen-lock
Synchronizing one equipment (controlled
or slave unit) to another (controlling or
master unit). The signal and tape run of
the VCRs used for editing, player and
recorder, are usually synchronized.
Gen-lock (generator lock)
See “External lock”.
Head drum
A metal cylinder to which a video head is
attached. This drum is rotated at high
speeds in synchronization with the sync
signal during recording and playback.
Insert editing
Editing in which new video/audio is added
into the middle of existing recorded video/
audio. You can freely select both video
and audio, video only, or audio only, for
an insert editing. You cannot use a blank
tape for an insert editing: it is necessary to
record time code and for example color bar
signals on your tape in advance. See also
“Assemble editing”.
IRE
A unit for representing a video level laid
down by the IRE (Institute of Radio
Engineers). The IRE is now the IEEE
(Institute of Electric and Electronic
Engineers).
Linear editing
Editing while playing back video and
audio signals recorded on video tape.
See also “Non-linear editing”.

LTC
Abbreviation of “Longitudinal Time
Code”. This timecode is recorded on a
longitudinal track on the tape. Reading is
unreliable at low speeds, and not possible
at all during still playback. See also
“VITC”.
Luminance signal
A signal that determined the brightness of
the picture. Also called “Y signal”.
Non-drop frame mode
The number of frames of the timecode and
video run is not adjusted. When you use
the timecode in non-drop frame mode, the
real playback time will be about 86
seconds shorter per day than the timecode.
If you edit frame by frame or if you
determine the length of a shot by counting
the timecode, use drop frame mode.
Non-linear editing
Editing while playing back video and
audio signals recorded on hard disks.
Video scenes stored on disk can be cued
up quickly, for increased editing
efficiency. See also “Linear editing”.
PCM audio
This is an audio signal represented by
pulse code modulation. The analog audio
signal is first broken down into a sequence
of pulses, and these are then represented
digitally.
Preroll
Running of a video tape to a prior to an
edit-start point to enable the tape to reach a
steady speed and to be synchronized with
other video tapes.
Reference video signal
A video signal which contains a sync
signal or sync and burst signals, used as a
reference for synchronization of video
equipment.

R–Y signal
One of the color difference signals, the R
(red) signal minus Y (luminance) signal.
Sampling frequency
The unit of time used when converting an
analog signal with a continuously varying
level to digital form by sampling the level
at a fixed interval. In general, a higher
sampling frequency makes it possible to
digitize analog signals of a higher
frequency.
SCH
Abbreviation of Sub Carrier to Horizontal.
The phase of the subcarrier with respect to
the phase of the horizontal synchronization
signal. In editing of monochrome video,
phase continuity is maintained by editing
in units of frames (two fields), so that the
continuity of the horizontal
synchronization signal phase is
maintained. Editing of color video must be
done in units of two frames (four fields) to
maintain subcarrier continuity. The SCH
of a field can be checked to find out which
of the four fields it represents. This allows
edited video signals to be joined while
maintaining subcarrier continuity.
Search
Viewing the picture or timecode by
running the tape in fast forward or rewind
mode, in order to search for a particular
scene.
Servo
A mechanism that controls the number and
phase of rotations of the head drum or
capstan. Servo mechanism allows
playback of the video signal without guard
band noise. The reference signal of the
servo control is normally a vertical sync
signal.
Servo lock
This refers to the synchronization of the
phase of the drum rotation and the
reference signal for the tape transport
position, so that the video heads can trace
the same pattern on the tape for playback
and recording.
Setup (for DSR-2000)
The difference between the reference black
level and the blanking level of a composite
signal.

SMPTE
Abbreviation of Society of Motion Picture
and Television Engineers, a professional
association established in the USA.
S/N
Signal-to-Noise ratio. The relation of the
strength of the desired signal to the
accompanying electronic interference, the
noise. If S/N is high, sounds are
reproduced with less noise and pictures are
reproduced clearly without snow.
Standby-off mode
One of the stop modes. In this mode, head
drum rotation is stopped and the tape
tension is slackened. It is not possible to
switch instantaneously from this mode to
recording or playback mode. This mode is
not harmful to the tape or heads.
Standby-on mode
One of the stop modes. In this mode, the
head drum continues rotating and the tape
remains wound onto the drum. This mode
enables instantaneous switching to
recording or playback mode. To prevent
damage to the tape or heads, the device
automatically switches from standby-on
mode to standby-off mode after a certain
period of time.
Subcarrier
Color information contained in a
composite video signal. Its amplitude is
for color saturation and its phase to color
burst is for hue.
Superimpose
To put one picture (or characters) onto
another so that both can be seen at the
same time.
S-video
A singal format in which Y (luminance)
and C (chrominance) signals are separated
to reduce interference between them so
that noiseless images are reproduced.
Sync
A reference signal consisting of vertical
and horizontal sync signals used for
synchronizing the scanning patterns of the
video camera and the monitor.
Synchronization
In video editing, alignment of the position
and speed of player and recorder VCRs
tapes. Carried out during preroll in order to
increase editing precision.

Tape tension
The tension applied to a tape. For the tape
to run properly while being wound on the
drum, it must be pulled lightly in the
opposite direction to the direction of
transport. Improper adjustment of tape
tension can cause deviations along the
temporal signal axis. In analog VCRs,
these deviations are evident as skew and
distortion in the upper part of the screen.
TBC
Abbreviation of Time Base Corrector.
Electronic circuits to electrically stabilize
the playback signals by removing color
variation and roll in the playback picture
caused by irregularity in drum rotation and
tape movement. Time base correction
reduces deterioration of picture quality
when transmitting or copying playback
signals.
Threading
See “Loading”.
Time code
The timecode is a tape position
information signal that includes time and
frame data that are recorded onto the tape
so as to facilitate searching of editing
points and recorded scenes when viewing
or editing.
SMPTE timecode is applied to NTSC
system, and EBU timecode is applied to
PAL/SECAM systems. There are two
kinds of signal recorded on tape. One is
longitudinal timecode (LTC) recorded
along the tape (the same way as audio and
CTL signals). The other is vertical
interval timecode (VITC). This code is
inserted in the vertical blanking period and
it is recorded on the tape with video
signals.
Time data
This refers either to time data that is
generated by a timecode generator or time
data that is played back from a tape and
read by a timecode reader.
Unloading
When the EJECT button is pressed, the
VCR automatically winds the tape back
into the cassette case. Also called
“Unthreading”.
Unthreading
See “Unloading”.

Appendixes

153

1-77

1-1. DSR-2000

Drop frame mode
Time code runs at 30 frames/sec. The
NTSC system, however, runs at about
29.97 frames/sec. Drop frame mode
adjusts this difference. The timecode and
video are synchronized by dropping the
first two frames of the timecode every
minute, except at the ten-minute marks.

E-E mode
Abbreviation of “Electric to Electric”
mode. In this mode, video and audio
signals input to the VCR are output after
passing through internal electric circuits,
but not through magnetic conversion
circuits such as heads and tapes. This can
be used to check input signals and for
adjusting input signal levels.

Loading
Also called “threading”. To pull the tape
out of the cassette case, thread it along the
specified tape path, and wrap it on the
drum in order to prepare it for recording or
playback. The VCR automatically loads
the cassette tape when you insert the
cassette into the cassette compartment.
There are two loading modes: standby-on
mode and standby-off mode.
Loop-through connection
See “Bridge connection”.

Appendixes

Bridge connection
A connection which allows a signal input
to an input terminal to pass through the
unit and exit from an output terminal as
input to external equipment.

Drum
See “Head drum”.

User bits
These are also referred to as “user’s bits”.
The user bits are a 32-bit segment of the
timecode recording area. The user can
select what to record in this segment and
how to use the recorded data. For
example, it can be used to record date
information in addition to the timecode
data or ID numbers for tape reels or
programs.

Appendixes

Video gain
Amount of amplification for video signals,
expressed in decibels (dB).
VITC
Abbreviation of “Vertical Interval Time
Code”. This timecode is inserted in the
vertical blanking interval and recorded on
the video tracks. It can be read at low
speeds and during still playback, but not
during high-speed playback.
See also “LTC”.
Y signal
See “Luminance signal”.

Index
A
AC IN connector 28
Adding a narration 95
Alarm messages 139
Analog
audio input/output section 31
interfaces 8
video input/output section 29
ASSEMBLE button 20
Assemble edit mode 67
Audio
level meters 13
recording level 46
AUDIO CH1, CH1/2 (CH2, CH3/4)
display 14
AUDIO IN
button 21
CH-1 to CH-4 connectors 32
LEVEL switches 32
switches 31

ClipLink log data
adding to/deleting from 103
creating 105
display 98
rewriting 100
ClipLink operation 97
Component analog recording
connections 131
COMPONENT VIDEO
IN connectors 30
OUT connectors 30
Condensation 135
Connections and settings 125
component analog recording 131
cut editing using i.LINK 125
cut editing using SDI 128
digital nonlinear editing using SDTI
(QSDI) 127
digitally dubbing signals in DVCAM
format 133
preread editing 129
settings on external editor 130
time code settings 130
two-unit synchronous playback 132

AUDIO OUT
button 21
CH-1 to CH-4 connectors 32

Connector panel 28

AUTO EDIT button 21

Continuous editing 91

Automatic editing 67
execution 82

Control panel
lower control panel 16
subsidiary control panel 25
upper control panel 13

B
Basic menu 107
items in the menu 107
menu operations 110

CONTROL PANEL
connector 31
switch 25
COUNTER SEL button 18

Capstan override 23

Cuing up to
adjacent Mark IN/cue points 99
any desired position 99
cue points 99
edit points 22, 78
Mark IN/OUT points 99

Cassettes 33
compartment 13
inserting/ejecting 34

Cut editing
using i.LINK 125
using SDI 128

BLACK LEVEL knob 27

Cassette memory indicator 19
CH1, 1/2 button 15
CH2, 3/4 button 15
CHANNEL CONDITION indicator 19

D
DELETE button 21

DMC EDIT button 21
Drop-frame mark 37
Duration display 76
DVCAM
cassettes 33
connections for digital dubbing 133
digital dubbing 61
Dynamic motion control playback 55

E
EDIT button 23
Edit mode 71
assemble edit 67
insert edit 68
setting section 20
Edit points
checking 75
cuing up 22, 78
duration display 76
modifying 76
setting 72
split edit points 73
time value display 75
Edit result checking 80
Editing
adding a narration 95
automatic editing 67
button/switch settings 70
continuous editing 91
DMC editing 84
manual editing 94
preread editing 87
quick editing 90
sequence of operations 69
standalone editing 93
Editing control section 21
E-E mode 13, 22, 23
EJECT button 23
ENTRY/SHIFT button 22

CHARACTER switch 25

DF/NDF switch 26

Error messages 139

Digital
input/output section 30
interfaces 8
jog sound 9
nonlinear editing using SDTI (QSDI)
127

Extended menu 113
items in the menu 113
menu operations 123

CHROMA PHASE (HUE) knob 27
ClipLink Guide 147
ClipLink indicator 19

DSR-2000/2000P

DIGITAL AUDIO (AES/EBU)
IN connectors 30
OUT connectors 31
Appendixes

DMC
editing 84
playback 55

CHROMA knob 27
CHROMA PHASE knob 27

154

Digitally dubbing DVCAM signals 61
connections 133
Display section 18

Index

V (vertical)-blanking
The portion of the video signal that occurs
between the end of one field and the
beginning of the next. During this time,
the electron beams in monitors are turned
off so that they can return from the bottom
of the screen to the top without showing
tracks of movement on the screen. When
the position of v-blanking is not adjusted
correctly, a horizontal black bar appears on
the screen.

1-1. DSR-2000

1-78
Glossary

External device connectors 31
External editor settings 130
External lock 42

Index

155

DSR-2000/2000P

Index

F FWD button 23

Maintenance 135

Fault display function 23

Manual editing 94

Features 7

Mark IN/OUT points
changing 100
cuing up to 99
deleting 103

FREE RUN/REC RUN switch 26

MEMORY indicator 21

Menu See Setup menu

Ground terminal 28

Menu bank operations 112

PLAYER button 17

SC knob 27

POWER switch 13

SDI
cut editing 128
INPUT connectors 31
OUTPUT 1, 2, and 3 (SUPER)
connectors 31

Preread
connections 129
editing 87
PREREAD button 17
Preroll 79
PREROLL button 22
Preview 80
PREVIEW button 21

SDTI/i.LINK button 14

PROCESS CONTROL switch 26

Search
control section 23
dial 23

MENU button 17
METER FULL/FINE button 16

MIXING button 15

Head cleaning 135

MONITOR AUDIO connector 32

HEADPHONES jack 17

Monitor output 81

HOLD button 18

MONITOR SELECT buttons 17

Q
Quick editing 90

Rack mount 10
REC
button 22
controls 16

i.LINK
button 15
connector 30
cut editing 125
digital dubbing 61

9PIN button 15

REC INHIBIT
indicator 19
switch 26

IN button 22

NOT EDITABLE indicator 20

REC MODE display 14

Initial time code value 39

N
Narration 95

Notes on use 143

INPUT display 14
Input selection section 14
Input selection/audio mode display section
13

O
OK/NG status 101

RECORDER button 17
Recording 45
button/switch settings
operation 48
time code/user bit values 47

SET UP knob 27
Setup menu 107
basic menu 107
extended menu 113
menu system configuration 107
75-ohm termination switch 29
SHUTTLE indicator 20
Shuttle mode 24
Sound-on-sound 95
Special editing methods 89
adding a narration 95
continuous editing 91
manual editing 94
quick editing 90
standalone editing 93

INPUT VIDEO display 14

Operating status display 35

Recording/playback format indicators 19

Specifications 144

INSERT buttons 20

Operation mode 37

Reel number 100

Standalone editing 93

Insert edit mode 68

OUT button 22

REF. VIDEO
IN connectors 29
OUT connector 29

STOP button 23
fault display function 23

INT/EXT–PRESET/REGEN switch 26
Interfaces 8

P
PB

button 18
controls 17

JOG indicator 20
Jog mode 24

K
KEY INHIBIT
indicator 19
switch 26

L
Lower control panel 16
position adjustment 12

Index

Reference level 46

Subsidiary control panel 25

Reference video signals for analog signal
editing 125

Superimposing text information 35

REMOTE button 15
Remote control setting section 15

PB/EE button 18

REMOTE-IN connector 31

PCM digital audio 7

REMOTE-OUT connector 31

PHONE LEVEL control 17

RESET button 18

PLAY button 23

REVIEW button 22

Playback 49
button/switch settings 49
capstan override 54
DMC playback 55
jog mode playback 51
normal playback 50
shuttle mode playback 52
synchronous playback 59
variable mode playback 53

REW button 23

Tape transport control section 22
TC SELECT switch 26

Time counter display 19
Time data
display 35
selection 49
Time data type 36
indicators 19
TRIM buttons 21
Troubleshooting 137
Two-unit synchronous playback
connections 132

U
Upper control panel 13
User bit
recording 47
setting 41

V
VARIABLE button 23
Variable speed mode 24
VIDEO CONTROL connector 31
VIDEO IN
button 14
connectors 29

SYNC knob 27

VIDEO knob 27
VIDEO OUT 1, 2, and 3 (SUPER)
connectors 30

Synchronous playback 59, 132

Y/C DELAY knob 27

TIME CODE
IN connector 29
OUT connector 29

Synchronizing time code generator 42
System configuration 11

Y, Z

Text information 35
Time code
generator/reader 9, 42
recording 47
setting 39

VITC
field 37
indicator 19
switch 26

S
S VIDEO
IN connector 29
OUT connector 29

Index

157

1-79

1-1. DSR-2000

156

PB FS display 14

STANDBY button 22

W, X
Wide screen 10

Index

Monitoring in E-E mode 22, 23

SEARCH button 23
SERVO indicator 19
SET button 17

Monitor/menu/display setting section 17

SDTI (QSDI)
digital nonlinear editing 127
INPUT connector 30
OUTPUT connector 30

T
Tape end alarm indicator 20

1-1. DSR-2000

1-80
DSR-2000/2000P

Sony Corporation

Printed in Japan

1-2. DSBK-190

DSR-2000/2000P

3-203-674-01(1)

English

For the customers in the USA

i.LINK/DV Input/
Output Board
Installation Instructions

This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction
manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own
expense.
You are cautioned that any changes or modifications not
expressly approved in this manual could void your authority to
operate this equipment.

English

The shielded interface cable recommended in this manual must
be used with this equipment in order to comply with the limits for
a digital device pursuant to Subpart B of Part 15 of FCC Rules.
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.

For the customers in Canada
This Class A digital apparatus complies with Canadian ICES003.

For the customers in Europe

DSBK-190

1-81

1-2. DSBK-190

 1999 by Sony Corporation

This product with the CE marking complies with the EMC
Directive (89/336/EEC) issued by the Commission of the
European Community.
Compliance with this directive implies conformity to the
following European standards:
• EN55103-1: Electromagnetic Interference (Emission)
• EN55103-2: Electromagnetic Susceptibility (Immunity)
This product is intended for use in the following Electromagnetic
Environment(s):
E1 (residential), E2 (commercial and light industrial), E3 (urban
outdoors) and E4 (controlled EMC environment, ex. TV studio).

1-2. DSBK-190

1-82

Table
of Contens
Table
of Contents
Overview ......................................................................... 12
Components of the DSBK-190 ..................................... 13
Installation ...................................................................... 14

Components of the DSBK-190
The DSBK-190 consists of the following items.

Overview
The DSBK-190 i.LINK/DV Input/Output Board is an optional
board for the DSR-2000/2000P Sony Digital Videocassette
Recorder. Installing this board in a DSR-2000/2000P allows
two DSR-2000/2000P units to be connected with an i.LINK/
DV 1) cable to form a cut editing system. The board also allows
the connection of a Sony consumer DV camera for direct
recording and editing.
Refer to the DSR-2000/2000P Operating Instructions for
information on connecting and operating the DSR-2000/2000P
with the DSBK-190 installed.

IF-763 board

Screw (M3 × 6,
silver-colored)

Washer

Connector panel

Harness

6-pin/4-pin cable
(1 m (3 feet))

6-pin cable (3.5 m (11 feet))

..........................................................................................................................
1)
DSR-2000/2000P

is a trademark of Sony Corporation, and indicates technology
complying with the IEEE1394-1995 specification and extensions
thereof.

DSR-2000/2000P

Installation
3

Caution

Remove the blank panel.

If this option is installed incorrectly, personal injury or damage
to peripheral items may occur due to fire, shock, or other
accidental circumstances. To avoid such risks, installation
should be performed by qualified service personnel.
To install the DSBK-190 in the DSR-2000/2000P, proceed as
follows.

Remove the top cover of the DSR-2000/2000P.
Loosen the three screws, and slide the top cover away from
the top retainer and blank panel.

Screw

Blank panel
Blank panel

Screw

Screw
Notes

Keep the blank panel and screw in a safe place for future
use.

Pass the harness through the opening in which the
connector panel fits and connect it to the connector panel;
then fasten the connector panel to the DSR-2000/2000P
with the screw.

Top retainer
Harness

Remove the board retainer.
Loosen the screw, then raise the board retainer and pull it
out from the board retainer guide.
Board retainer

Connector panel
Board retainer guide

Screw
Supplied screw (silver-colored)
and washer

(Continued)

1-83

1-2. DSBK-190

1-84

Installation

Pass the harness through the cable holder on the IF-763
board, and connect to connector CN401.

Fix the harness in the cable holder by the board slot.

Cable holder
Connector CN401

Cable holder

IF-763 board

Insert the IF-763 board in the board slot (fourth from the
outside).
Align the three connectors on the bottom of the board with
the three connectors inside the unit, and push the board
firmly into place.

(Continued)

IF-763 board

DSR-2000/2000P

Installation

Replace the board retainer which you removed in step 2, in
its original position.
Push the board retainer into the board retainer guide, and
fasten the screw in the screw hole.
Check that the six claws on the underside of the board
retainer engage with the boards in the slots to hold them in
position.

Board retainer guide

Screw

Board retainer claw

1-85

1-2. DSBK-190

Replace the DSR-2000/2000P top cover.

English

For the customers in the USA

Remote Control
Panel
Installation Instructions

This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.

For the customers in Canada
This Class A digital apparatus complies with Canadian ICES003.

For the customers in Europe

DSBK-200
DSR-2000/2000P

 1999 by Sony Corporation

English

The shielded interface cable recommended in this manual must
be used with this equipment in order to comply with the limits for
a digital device pursuant to Subpart B of Part 15 of FCC Rules.

1-3. DSBK-200

1-86

3-203-675-01(1)

DSR-2000/2000P

Installation
Table of

Contents

Overview ......................................................................... 10
Components of the DSBK-200 ..................................... 11
Installation ...................................................................... 12

Components of the DSBK-200
The DSBK-200 comprises the following items.
Remote control panel

Overview
The DSBK-200 Remote Control Panel is an optional remote
control panel for the DSR-2000/2000P Sony Digital
Videocassette Recorder. Connecting this remote control panel
to the DSR-2000/2000P allows the DSR-2000/2000P to be
remotely controlled.
Normally, use this remote control panel installed in the
optional BKNW-121 Control Panel Case.

Double-sided adhesive tape
(two pieces)
Interface cable (10 m (32 ft.))

For details of the functions of the buttons on this remote
control panel, refer to the Operating Instructions for the DSR2000/2000P.

1-87

1-3. DSBK-200

1-88

Installation
Installation
Use the following procedure to install the DSBK-200 Remote
Control Panel in the optional BKNW-121 Control Panel Case.

Pass the flat cable connector and ground wire of the
interface cable through the hole at the rear of the bottom of
the control panel case, to the interior of the control panel
case.

Connect the flat cable connector to the connector on the
bottom of the remote control panel, then remove the screw
for grounding and tighten it together with the ground wire.
Fix the flat cable connector in place by fastening the
retaining clips at each end of the connector on the remote
control panel.
Connector on the bottom of
the remote control panel

Control panel case
Interface cable

Flat cable connector

Ground wire
Retaining clips
Ground wire

Screw for grounding

Flat cable connector
Note

Make sure that the projection on the underside of the
connector matches the cutout on the control panel
connector. The connector cannot be inserted upside down.
(Continued)

DSR-2000/2000P

Installation

Use the cable straps on the base of the control panel case to
hold the cable tidy, as required.

Attach the double-sided adhesive tape to the edge of the
remote control panel as shown in the figure, then pull
forward the cushion part of the control panel case, and
insert the remote control panel.
Remote control panel
Double-sided adhesive tape

Interface
cable

Cable strap

Cushion

Slacken the two screw fasteners in the base of the control
panel case.

Slide the cushion part of the control panel case back, to
hold the remote control panel in place, then turn the screw
fasteners in the base of the control panel case to hold the
cushion part in position.

Connect the D-sub 15-pin connector of the interface cable
to the CONTROL PANEL connector of the DSR-2000/
2000P, and fasten the connector with the retaining screws.
DSR-2000/2000P

Screw fasteners

D-sub 15-pin
connector

Retaining screws

1-89

1-3. DSBK-200

Interface cable

1-3. DSBK-200

1-90

Installation

Using the remote control panel
Power on the DSR-2000/2000P, and in the subsidiary control
panel, set the CONTROL PANEL switch to EXT. This lights
the ON LINE indicator of the remote control panel, indicating
that it is ready for use.
If you set extension menu item 117 on the DSR-2000/2000P to
PARA, you can use both this remote control panel and the
DSR-2000/2000P control panel.
For more information about this, refer to the Operating
Instructions for the DSR-2000/2000P.

DSR-2000/2000P

Section 2
Installation
Be sure to install the DSR-2000/2000P in location satisfying the required operational environment described below to
assure the DSR-2000/2000P superior performance and to maintain the excellent serviceability and accessibility.

2-1. Installation Procedure
Start
Determination of
installation place

Unpacking
Rack mounting

· · · 2-2. Operational Environment
· · · 2-3. Operating Voltage
· · · 2-4. Installation Space

· · · 2-5. Supplied Accessories
· · · 2-7. Mounting

Connectors

· · · 2-8-1. Connectors/Cables
· · · 2-8-2. Input/Output Signals of the Connectors

Initial setup

· · · 2-9. Installation Setup and Adjustment

Operation check

· · · If an error message is shown on the time counter, refer to
“Section 4. Error Message” in service manual.

END

2-2. Operational Environment
.
.
.
.

Operating temperature :
Humidity :
Storage temperature :
Locations to avoid :

. Horizontal condition :

+5 dC to +40 dC
80 % or less
_20 dC to +60 dC
. Areas where the unit will be exposed to direct sunlight or any other strong lights.
. Dusty areas or areas where it is subject to vibration.
. Areas with strong electric or magnetic fields.
. High-temperature environment.
(Good air circulation is essential to prevent internal heat build-up. Place the unit in location
with sufficient air circulation. Do not block the ventilation holes on the sides of the cabinet
and the rear panel.)
within ± 30 d

2-3. Operating Voltage
. Power voltage :
. Power frequency :
. Power consumption :

DSR-2000/2000P

AC 100 V to 240 V
50/60 Hz
110 W

2-1

2-4. Installation Space
2-5. Supplied Accessories
2-6. Optional Accessories

2-4. Installation Space
. The rear side must be at least 40 cm away from the walls for ventilation and maintenance.
. When the unit is operated on a desk or similar condition, assure that the clearance above the unit is at least 40 cm to
provide accessibility to the printed circuit boards and other mechanical parts. Note that it is not necessary to provide the
space when the unit is mounted in a rack since the printed circuit boards can be repaired after it is pulled out.

DIGITAL VIDEOCASSETTE RECORDER DSR-2000

INPUT SELECT
SDTI/I.LINK

POWER

REMOTE
VIDEO IN
9PIN

CH-1,1/2
CH-2,3/4

I.LINK

372
424
427

27.5

Set’s height at
( rack
mounting. )

16.5

115
98.5

174.5

191

MIXING

ø20
52.5

400
495.5
602.3

19.7

4.8

577 (maximum traveling distance)

87.5

174.5

30 (handle hight)

With the unit mounted in the rack
(height as slide rail center)

Unit : mm

2-5. Supplied Accessories
. AC power cord :
. RCC-5G 9-pin remote cable :
. Operating instructions :

1
1
1

2-6. Optional Accessories
.
.
.
.
.
.
.
.

i.LINK/DV input/output board :
DSBK-190
Extension control panel :
DSBK-200
TBC remote control unit :
UVR-60/60P
Rack mount Kit :
RMM-130
(The unit can be mounted in a 19-inch standard rack)
Remote control cable :
RCC-5G/10G/30G
Cleaning cassette tape :
DV12CL (Standard size), DVM12CL (Mini size)
Digital video cassette (Mini size) :
PDVM-12ME/22ME/32ME/40ME
Digital video cassette (Standard size) : PDV-64ME/94ME/124ME/184ME

2-2

DSR-2000/2000P

2-7. Rack Mounting

2-7. Rack Mounting
The unit can be mounted in a 19-inch standard rack.
It is recommended to use the following kit.

1. Remove the four screws on right and left side panels.
And install the Inner Members of the rails to the right
and left side panels with the screws removed.
Screws (B4 x 6)

Rack Mount Kit :

Inner member

RMM-130
(optional accessory)

or
RACK-MOUNT SLIDES : MODEL 305 slide length 22
inch (ACCURIDE)
Note for rack mounting :
. When several VTRs are mounted in a rack, it is recommended to install a fan for ventilation. Good air circulation is essential to prevent internal heat build-up in a
rack.
. The unit must be kept in an operating temperature range
from +5 d to +40 dC.
. Never remove an upper panel and lower panel during
rack mounting.
. Be sure to secure the rack to the floor to avoid accidents
when a unit is pulled out.
. Connect long enough cables on the connector panel,
considering that the unit is pulled out.
. Maximum two units can be mounted in a stack. For three
units of more, keep a space for one unit between the
mounted units, using a rack. The space should be 44 mm
or more in height.

Screws (B4 x 6)
Inner member

2. Install the Outer Member Brackets of the slide rails to
the rack. Adjust the distance from the edge of the slide
rail to the outside of the rack so that it meets the
required specification.
L-angle

Outer member

Bracket

L-angle

DSR-2000/2000P

+5
_0

Rack

2-3

2-7. Rack Mounting

3. Remove the two screws (B4 x 8) on the right and left
side panels. (Be careful not to lose these four screws.)

Screws (B4 x 8)

4. Install the L-angles to the holes described in step 3
with the supplied screws (PSW4 x 16) in RMM-130
for these L-angles.
Screws
(PSW4 x 16)

L-angle

Screws
(PSW4 x 16)

L-angle

n
Never use screws PSW4 x 16 to install the right and left
side panels without L-angles. Be sure to use the screws
B4 x 8 removed in step 3. Screws for L-angles are longer
than ones for the side panels. Therefore, using the screws
PSW4 x 16 may cause trouble in the unit.

2-4

DSR-2000/2000P

2-8. Connectors

2-8. Connectors
2-8-1. Connectors/Cables
When external cables are connected to the connector on a connector panel during maintenance, the following (or equivalents) must be used.
Connectors on DSR-2000/2000P Side
Panel indication
ANALOG IN
REF. VIDEO IN
TIME CODE IN
VIDEO IN
COMPONENT VIDEO IN

Connector/Cable
Designation

Sony Part No.

BNC, MALE

1-560-069-11

S VIDEO IN

YC-15 V (1.5 m)

optional accessory

AUDIO IN CH-1/2/3/4

XLR 3P, MALE

1-508-084-11

BNC, MALE

1-560-069-11

MONITOR AUDIO

PIN PLUG

Standard Product

S VIDEO OUT

YC-15 V (1.5 m)

optional accessory

ANALOG OUT
REF. VIDEO OUT
TIME CODE OUT
VIDEO OUT
COMPONENT VIDEO OUT

AUDIO OUT CH-1/2/3/4

XLR 3P, FEMALE

1-508-083-11

IEEE1394 6P (1 m)
IEEE1394 6P (3.5 m)

1-782-408-21
1-791-184-11

SDI INPUT

BNC, MALE

1-560-069-11

SDI OUTPUT

BNC, MALE

1-560-069-11

SDTI (QSDTI) INPUT

BNC, MALE

1-560-069-11

SDTI (QSDTI) OUTPUT

BNC, MALE

1-560-069-11

DIGITAL AUDIO (AES/EBU)
INPUT CH-1/2, CH-3/4

BNC, MALE

1-560-069-11

OUTPUT CH-1/2, CH-3/4

BNC, MALE

1-560-069-11

D-SUB 15P, FEMALE

1-561-610-21

i.LINK

VIDEO CONTROL
CONTROL PANEL

D-SUB 15P, MALE

1-561-651-11

REMOTE-IN

D-SUB 9P, MALE

1-560-651-11

REMOTE-OUT

D-SUB 9P, MALE

1-560-651-11

DSR-2000/2000P

2-5

2-8. Connectors

2-8-2. Input/Output Signals of the Connectors
INPUT
REF.VIDEO :

VIDEO IN :
COMPONENT VIDEO :

S VIDEO :

SDI INPUT :

SDTI (QSDI) :

AUDIO IN :
DIGITAL AUDIO (AES/EBU) :
TIME CODE :

i.LINK :

2-6

BNC x2 (loop-through)
NTSC black burst, 0.286 V p-p, 75 Z, sync negative
PAL black burst, 0.3 Vp-p , 75 Z sync negative
BNC x2 (loop-through)
Composite, 1.0 V p-p, 75 Z, sync negative
BNC x3
Y:
1.0 V p-p, 75 Z, sync negative
R-Y/B-Y : 0.7 V p-p, 75 Z (NTSC : 75 % PAL : 100 %)
DIN 4P x1
Y : 1.0 V p-p, 75 Z, sync negative
C : NTSC 0.286 V p-p (burst level), 75 Z
PAL
0.3 V p-p (burst level), 75 Z
BNC x2 (active-through)
Serial digital interface format (270 Mbps),
SMPTE 259M (NTSC)/ITU-R BT.656 (PAL)
BNC x1
Serial data transport interface
(DVCAM compression signal : Video + Audio + TC signal)
SMPTE 305M/322M
XLR 3P x4
Reference level switchable (_6/0/+4 dBu), 600 Z/10 kZ switchable, balanced
BNC x2 (conformed with AES-3id-1995)
BNC x1
SMPTE (NTSC)/EBU (PAL)
0.5 to 18 V p-p, 3 kZ, unbalanced
IEEE1394 connector 6P x1

DSR-2000/2000P

2-8. Maching Connectors

OUTPUT
REF.VIDEO :

VIDEO OUT1, 2, 3(SUPER) :
COMPONENT VIDEO :

S VIDEO :

SDI OUTPUT1, 2, 3(SUPER) :

SDTI (QSDI) :

AUDIO OUT :
MONITOR AUDIO :
DIGITAL AUDIO :
TIME CODE :

i.LINK :

DSR-2000/2000P

BNC x1
NTSC composite sync, 0.286 V p-p, 75 Z, sync negative (with burst signal)
PAL composite sync, 0.3 V p-p, 75 Z, sync negative (with burst signal)
BNC x3
Composite, 1.0 V p-p, 75 Z, sync negative
BNC x3
Y:
1.0 V p-p, 75 Z, sync negative
R-Y/B-Y : 0.7 V p-p, 75 Z (NTSC : 75 % PAL : 100 %)
DIN 4P x1
Y : 1.0 Vp-p, 75 Z, sync negative
C : NTSC 0.286 V p-p (burst level), 75 Z
PAL
0.3 V p-p (burst level), 75 Z
BNC x3
Serial digital interface format (270 Mbps),
SMPTE 259M (NTSC)/ITU-R BT.656 (PAL)
BNC x1
Serial data transport interface
(DVCAM compression signal : Video + Audio + TC signal)
SMPTE 305M/322M
XLR 3P x4, MALE
+4 dBu, 600 Z load, balanced (low impedance)
PHONO JACK x1
_6 dBu, 47 kZ load, unbalanced
BNC x2 (conformed with AES-3id-1995)
BNC x1
SMPTE (NTSC)/EBU (PAL)
2.2 V p-p ± 3.0 dB, 600 Z, unbalanced
IEEE1394 connector 6P x1

2-7

2-8. Connectors

VIDEO CONTROL (D-sub 15 pin : MALE)

Pin No.

Signal

Operating Voltage

IN/OUT

SYNC CONTROL

_5 V to +5 V

HUE CONTROL

_5 V to +5 V

SC CONTROL

_5 V to +5 V

VIDEO LEVEL CONTROL

_5 V to +5 V

SET UP CONTROL

_5 V to +5 V

CHROMA LEVEL CONTROL

_5 V to +5 V

_9 V SUPPLY

_9 V

OUT

GND

FRAME GND

Y/C DELAY CONTROL

_5 V to +5 V

+9 V

OUT

14
15

+9 V SUPPLY

3 4

9 10 11 12 13 14 15

CONTROL PANEL (D-sub 15 pin : FEMALE)

Pin No.

Signal

SCK

UNREG

+12 V

UNREG

+12 V

UNREG

+12 V

KY EXT

GND

UNREG GND

2-8

Operating Voltage

15 14 13 12 11 10

1
9

DSR-2000/2000P

2-8. Connectors

REMOTE (D-sub 9 pin : MALE)

S VIDEO (Circular 4 pin)

4
9

3
8

2
7

4
2

Pin No.

Controlling Device

Controlled Device

Pin No.

Output Signal

FRAME GROUND

Y (G)

RECEIVE A

TRANSMIT A

C (G)

TRANSMIT B

RECEIVE B

Y (X)

TRANSMIT COMMON

RECEIVE COMMON

C (X)

PRIORITY IN

PRIORITY OUT

RECEIVE COMMON

TRANSMIT COMMON

RECEIVE B

TRANSMIT B

TRANSMIT A

RECEIVE A

FRAME GROUND

DSR-2000/2000P

3
1

2-9

2-9. Installation Setup and Adjustment

2-9. Installation Setup and Adjustment
2-9-1. Switch Settings on the Connector Panel
When the unit is installed, be sure to perform the following setup and adjustment. If the adjustment is not
performed, the unit may not operate properly.
Refer to the operating instruction “Chapter 1 Overview” for setup and adjustment.
[Connector Panel]
(1) The setting of 75 Z termination switch :
REF VIDEO 75 Z ON/OFF
ON : When the line is terminated in this unit.
OFF : When another unit is connected with this unit.
(2) The setting of video input termination switch :
VIDEO INPUT 75 Z ON/OFF
ON : When the line is terminated in this unit.
OFF : When another unit is connected with this unit.
(3) The setting of audio input level select switch :
+ 4 dBm : +4 dBu reference level on output side
0 dBm : 0 dBu reference level on output side
_ 6 dBm : _6 dBu reference level on output side

2-10

DSR-2000/2000P

2-9. Installation Setup and Adjustment

2-9-2. Front Panel Setting
[Control Panel]
(1) VIDEO INPUT select switch setting : COMPOSITE ; Ordinary video signal
S VIDEO ;
Y/C separation type S Video signal
Y-R, B ;
Component signal (Betacam)
SDI ;
Component digital signal
SDTI/i.LINK ; DV compressed digital signal
(2) AUDIO INPUT SELECT :
Analog/Digital (AES/EBU)/SDI
[SUB sidiary Control Panel]
(1) CHARACTER :
(2) CONTROL PANEL :
(3) REC INHIBIT :
(4) KEY INHIBIT :
(5) PROCESS CONTROL :
(6) INT/EXT-PRESET/REGEN :
(7) FREE RUN/REC RUN :
(8) DF/NDF :
(9) VITC :
(10)TC SELECT :
(11)VIDEO :
(12)SET UP :
(13)CHROMA :
(14)Y/C DELAY :
(15)CHROMA PHASE :
(16)SYNC :
(17)SC :

DSR-2000/2000P

Selects either the character information is superimposed in the
video signal or not.
Selects the status of the control panel when operating this unit.
Inhibits recording on a tape.
Disables operation of the buttons specified on the upper/lower
control panels.
Selects the control method and setting of the built-in digital
video processor.
Selects internal time code/external time code, and preset the
built-in time code generator.
Selects synchronous operation of the built-in time code
generator.
Selects the synchronous operation of the time code generator
and the counter.
Sets ON to record the VITC generates in the built-in time code
generator.
Selects the time code displayed on the time counter display
block.
Adjusts the output level of the video signal.
Adjusts the setup level.
Adjusts the output level of the chroma signal.
Adjusts the amount of the Y/C delay.
Adjusts the chroma phase (the relative phase with the burst
signal).
Adjusts the sync phase of the output signal.
Adjusts the phase of the subcarrier.

2-11

2-9. Installation Setup and Adjustment

2-9-3. On-board Switch Setting
SV-212 board
A

1
S101

SV-212 BOARD (A SIDE)

n
Do not change the setting of switches when the “factory use” is shown in the description.
Ref No.

Description

Factory Setting

S101-1

HOURS METER can enter reset mode.

OFF

S101-2

factory use

OFF

S101-3

Use this switch when operating the machine with cassette compartment removed.

OFF

S101-4

This defeats an error detection of mechanism and setvo system alignment.

OFF

S101-5

factory use

OFF

S101-6

factory use

OFF

S101-7

factory use

OFF

S101-8

factory use

OFF

2-12

DSR-2000/2000P

2-9. Installation Setup and Adjustment

SY-278 board
A

D
S101

S201

SY-278 BOARD (A SIDE)

n
Do not change the setting of switches when the “factory use” is shown in the description.
Ref No.

Description

Factory Setting

S101

Push this switch when resetting the system control.

—

S201-1

factory use

OFF

S201-2

factory use

OFF

S201-3

factory use

OFF

S201-4

factory use

OFF

S201-5

factory use

OFF

S201-6

factory use

OFF

S201-7, 8

Destination setting

DSR-2000/2000P

Destination

bit-7

bit-8

UC
J
CE

OFF
ON
OFF

OFF
OFF
ON

—

2-13

2-9. Installation Setup and Adjustment

VPR-62 board
A

S200

VPR-62 BOARD (A SIDE)

Ref No.

Name

Description

Factory Setting

S200

A/D LEVEL REF

. Use this switch when performing the A/D level adjustment.
OFF
. When this switch is set to ON, the standard-level signal
generated based on the internal data is output for adjusting
the A/D level.
Return the setting of the switch (S200) to OFF position.
n
The switch (S200) on the VPR-62 board functions only when
the switch (S101-1) on the SV-212 board is set to ON position

2-9-4. System Adjustment After Installation
Observe the following precautions when this equipment is used for editing system.
. The REF. VIDEO INPUT requires video signal which is in comfomity with the RS-170A.
. Adjust the sync phase of this equipment to the system sync with [SYNC PHASE] control on the sub
control panel.
. Adjust the SCH phase of this equipment to the system SCH with [SC PHASE] control on the sub
control panel.
. When this unit is connected to a switcher that does not have the sync switching function, the SYNC/
BURST level adjustment is required.

2-14

DSR-2000/2000P

Section 3
Service Overview
3-1. Location of Main Parts
3-1-1. Location of Printed Circuit Boards

@\
@]
3

@=
@-

7
@;
9
!/

!=
!,

!'
!;
!\
!]

4
6
3
8

DSR-2000/2000P

3-1

3-1. Location of Main Parts

No.

Board Name

Circuit Configuration

APR-45

Audio process

VPR-62/62P

Analog video input . output process/reference

DPR-136

Digital process

DU-83

Serial No. 100001-100910: UC
400001-401550: CE

Digital process

DU-95

Serial No. 100001-100290: UC
400001-400300: CE

SDI character generator

DU-84

Serial No. 100001-101240: UC
400001-401550: CE

Digital process

IF-763

DU-89

DY-15

Fluorescent display board/audio meter/input . output selection

VR-260

Audio REC volume control

HP-99

Headphone interface

VR-259

Audio PB volume control

KY-452

Operation panel

PTC-100

Search dial sensor

SW-11/11P

Switch

SW-17

Remote switch

MB-859

Mother board

RP-111

RF REC/PB, ATF detection

EX-752

Intermediate board

CP-341

Video/remote interface

SV-212

Servo/mechanism control

SY-278

System control

CN-1968

i.LINK connector board (Option: DSBK-190)

CP-342

Audio interface

FU-78P Serial No. 101241-: UC
401551-: CE

Digital process (PB)

FU-78R Serial No. 101241-: UC
401551-: CE

Digital process (REC)

3-2

i.LINK interface board (Option: DSBK-190)
Serial No. 100001-101240: UC
400001-401550: CE

Digital process

DSR-2000/2000P

3-1. Location of Main Parts

Locations of Mechanism Deck

1
2

6
5
3
4

No.

Board Name

Circuit Configuration

SE-521

Mode sensor/tape end sensor/loading motor FG sensor

SE-538

Tension sensor

CN-1863

Sensor input/output board

SE-525

LED signal board

SE-522

Tape top sensor/reel position sensor (Mini/M/Standard)

MS-64

Servo/mechanism control

DSR-2000/2000P

3-3

3-1. Location of Main Parts

Locations of Cassette Compartment

4
2

No.

Board Name

Circuit Configuration

CN-2021

Intermediate board between CC-84 and CC-83

CC-83

Cassette compartment mode detection/intermediate board

CC-85

Cassette compartment cassette in detection

CC-84

Cassette compartment cassette type detection

CN-2022

Intermediate board between CC-85 and CC-84

3-4

DSR-2000/2000P

3-1. Location of Main Parts

Locations of DSBK-2000 (Option)

2
3

No.

Board Name

Circuit Configuration

IF-778

Operation panel intermediate board (Option: DSBK-200)

KY-452A

Operation panel board (Option: DSBK-200)

PTC-100

Search dial sensor

DSR-2000/2000P

3-5

3-1. Location of Main Parts

3-1-2. Location of Main Mechanical Parts
2

1
@]

@[
@=

4
5

6
7

!,
!'
!;

!\
0

!]
!-!=

1
2
3
4
5
6
7
8
9
!/
!!=
![
3-6

Head cleaning solenoid
Loading motor
TG1 arm assembly
Shuttle (left) assembly
S tension regulator assembly
S reel motor
S brake assembly
Brake solenoid
M stop solenoid assembly
T brake assembly
MIC assembly
MIC holder assembly
T reel motor

!]
!\
!;
!'
!,
!.
@/
@@=
@[
@]
@\

Shuttle (right) assembly
T drawer arm assembly
TG8 arm assembly
Capstan motor
Elevator cam
Pinch solenoid assembly
Reel shift motor
Pinch roller
HC roller assembly
Drum assembly
Rail assembly
Cassette compartment motor assembly

DSR-2000/2000P

3-1. Location of Main Parts

3-1-3. Location of Sensors
Sensor Location Diagram (1) ..... Mechanism Deck

1
2
4
3

!/
!-

7
9

1, 2 Mode sensor
Detects the mechanism position during threading.
3 Tape top/end detect LED
Detects the top and end of a tape.
4 Condensation sensor
Detects condensation occurred in DSR-2000/2000P.
5 Tape top sensor
Detects the beginning of a tape that runs in the REV
direction.
6 Reel position sensors (4 pieces) (Mini, M, Standard
reel position)
Detects the reel table position at the each specified reel
position according to the cassette type.
7 Reel FG sensor (Take-up side)
Detects rotation of the take-up reel table. The FG
output of the sensor is sent to the servo circuit and
used to control the rotating speed and torque of the reel
motor.
8 Record proof sensor (common to standard, M and mini
size cassettes)
Protects a tape from mis-recording.

DSR-2000/2000P

9 Cassette memory terminal
Determines whether cassette memory is used, and
reads and writes data to and from the cassette memory.
!/ Tension sensor
The tension arm keeps the tension of a running tape
constant during recording and playing. The tension
sensor detects the mechanical position of the tension
arm.
!- Reel FG sensor (Supply side)
Detects the rotation of the supply reel table. The PG
output of the sensor is input to the servo circuit and
controls the rotating speed and torque of the reel
motor.
!= Tape end sensor
Detects the end of a tape that runs in the FWD direction.
![ Threading motor FG sensor
Detects the rotation speed of the gearbox motor. The
FG output of the sensor is input to the servo circuit and
controls the threading speed so that excessive force is
not applied to the tape during threading.

3-7

3-1. Location of Main Parts

Sensor Location Diagram (2) ..... Cassette compartment

1 S3
2 PH1
2 PH2
2 PH3

3 PH4
1 S1

1 S2
3 PH5

3 PH7
3 PH6

1 The sensors S1, S2 and S3 discriminate the inserted cassette type among the mini, M, standard
cassettes and the cassette adaptor for DVCPRO by on/off of the sensors.
2 The sensors PH1, PH2 and PH3 detect the movement of a cassette compartment by their combination.
3 The sensors PH4 and PH5 detect that a mini cassette got inserted.
The sensors PH4 and PH6 detect that a M cassette got inserted.
The sensors PH4 and PH7 detect that a standard cassette got inserted.

3-8

DSR-2000/2000P

3-2. Functions of Record Proof Hole and Record Proof Plug of Cassette

3-2. Functions of Record Proof Hole and Record Proof Plug of Cassette
Standard cassette, M cassette
Cassette cover release claw

Record proof
hole
4 3 2 1
Record proof plug

Reel rotation stopper

Hole and plug for record proof

Mini cassette

Record enable
REC
SAVE

Record protect
REC
SAVE

. This plug controls the record proof
switch according to open or close
position.

Cassette cover release claw

Record proof
hole
4 3 2 1

Reel rotation stopper

Record proof plug

Pin No.

Function
Equipped with built-in memory

Not equipped with built-in memory

+DC

Detecting tape thickness

DATA

Detecting tape type (Example: ME/MP)

CLOCK

Detecting tape application (Example: consumer/professional)

GND

DSR-2000/2000P

3-9

3-3. Removal/Installation of Cabinet

3-3. Removal/Installation of Cabinet
n
Turn off the power of the unit before starting removal/installation.
B4 x 6
Fixing screw
(with stopper)

Claw

Top panel

B4 x 8
Section A

Left side panel

Section A

B4 x 8

Claws

Front panel
Claw
PWH3 x 6

B4 x 8
Claw

B4 x 8
Right side panel

PWH3 x 6

Foot
Claw

Hole
BVTT3 x 6

Bottom panel
BVTT3 x 6

3-10

DSR-2000/2000P

3-3. Removal/Installation of Cabinet

Removal/Reattachment of the Top Panel
(1) Loose the three screws and remove the top panel in the
arrow direction.
n
The screws do not come off the top panel, because of a
stopper attached to the screw.
Do not forcibly remove the screws from the top panel.
(2) Insert the two claws of the top panel in the section A
shown in the figure, and tighten the three screws to
reattach the top panel.

Removal/Reattachment of the right and left side
panels
[Reference]
A same procedure is performed when removing/reattaching the right and left side panels.
(1) Remove the four screws shown in the figure and
remove the side panel.
(2) Hook the side panel at the three claws in the chassis,
and while pulling the side panel in the arrow direction,
tighten the four screws (B4 x 8).
Removal/Reattachment of the front panel

Removal/Reattachment of the Bottom Panel
(1) Place the unit with the right side panel facing down.
(2) Remove the six screws and remove the bottom panel.
(3) With the claw of the bottom panel positioning as
shown in the figure, fit the four holes in the bottom
panel on the feet.
(4) Tighten the six screws to reattach the bottom panel.

DSR-2000/2000P

(1) Remove the top panel.
(2) Remove the two screws securing the front panel.
(3) Insert hands in the space between the front panel and
the chassis and pick up the upper rim of the front
panel, and then release the four claws of the front
panel.
(4) Pull out the front panel to your side and detach it.
(5) While hooking the four claws of the front panel at the
three crooks of the chassis and the crook of the
cassette compartment holding assembly, insert the two
protrusions to the notch and hole of the chassis.
(6) While pressing the front panel against the unit, fix the
front panel with the two screws.

3-11

3-3. Removal/Installation of Cabinet

Removal/Reattachment of the control panel
(1) Remove the nine knobs.
(2) Hold the handles of the control panel and open the
control panel. Lift up the control panel with the
handles until it comes horizontally.
(3) Remove the three screws.

Knob‘s turning range

Knobs

Handle

PWH3 x 6

PWH3 x 6
PWH3 x 6
Control panel

(4) While pressing the release lever, bring back the control
panel to the original position until the angle between
the control panel and the unit comes to about 45
degrees.
(5) Move the control panel in the arrow direction, and
release the three claws to remove the control panel.
[Reference]
Applying the pulling downward force will make it
easy to remove the control panel.
(6) Fit the three claws of the control panel into the three
square holes of the control frame assembly.
(7) Bring the control panel to the position of Step (2), and
while pressing it from the top, reattach it with the three
screws.
(8) Turn the nine volume shafts fully counterclockwise.
(9) Align the nine knobs with the position holes of the
control panel and thrust into as far as they will go.
[Reference]
If the knob easily comes off, widen the slot on the
volume shaft using a flat tip screwdriver.

Lift up in the
horizontal
position

Claws

Control panel

Square hole

Square
holes

Control frame assembly
At angle up to 45d

(10)Check that the knob’s turning range is within the
double-headed arrow shown in the figure by turning
the nine knobs clockwise and counterclockwise.

3-12

DSR-2000/2000P

3-4. Removal/Reattachment of the Cassette Compartment

3-4. Removal/Reattachment of the
Cassette Compartment
Removing
(1) Remove the top panel. (Refer to Section 3-3.)
(2) Disconnect the flexible card wire from the connector
(CN1) of the CC-83 board.
[Reference]
Hanging the flexible card wire disconnected at the
hook on the top of the PC guide B provides an easy
performance to the succeeding steps.
(3) Unscrew the three screws and lift off the cassette
compartment holding assembly in the arrow A direction.
n
The screws do not come off the cassette compartment
holding assembly, because of a stopper attached to the
screw.
Do not forcibly remove the screws from the top panel
(4) Remove the cassette compartment in the arrow B
direction.
Fixing screw
(with stopper)

Reattaching
(1) Insert the cassette compartment in the reverse direction
of arrow B and align the three holes and the notch of
the cassette compartment with the four positioning
pins of the chassis.
n
Use care not to involve a lead wire of the reel shift
motor when reattaching the cassette compartment.
(2) Insert the cassette compartment holding assembly in
the reverse direction of arrow A.
Fit the hole and notch of the assembly on the shafts a
and b of the cassette compartment respectively and fix
it using the three screws while drawing the cassette
compartment holding assembly in the C direction.
(3) Reconnect the flexible card wire to the connector
(CN1) of the CC-83 board.
(4) Reattach the top panel. (Refer to Section 3-3.)
A

Cassette compartment retainer assembly
Fixing screws (with stopper)

Connector
(CN1)

Cassette compartment

CC-83 board

Flexible card wire

b
a

Hook

Positioning
pin

Positioning pin

DSR-2000/2000P

Positioning pins

3-13

3-5. Removal/Reattachment of the Boards

3-5. Removal/Reattachment of the
Boards
n
Be sure to remove the board after turning off the power.

3-5-1. Removal/Reattachment of the Card
Boards
(1) Remove the top panel. (Refer to Section 3-3.)
(2) Loosen the screw shown in the figure and remove the
board retainer assembly.
. The screw has a drop-protector so that it cannot fall
out of the board retainer assembly.
(3) Push up the board lever in the arrow direction and
raise it upwards.
(4) Reattach the board in the reverse order of the removing steps (1) to (3).
m
. Insert the board along the board guide rails until it
connects firmly with the connector of the motherboard.
. Set the board to claws of board retainer firmly.

Board retainer assembly
B3 x 6

Square hole

Hook

Board lever
Card board

Board lever

3-5-2. Extension Board
An optional extension board is supplied to check and
adjust the card boards. Attach the extension board to this
unit and attach the board to be checked and adjusted to the
top of the extension board.
Extension board
connected

Card boards which can be

DJ-493
APR-45, DPR-136, IF-763 (DSBK-190),
(Part No.: J-6444-930-A) SV-212, SY-278, VPR-62/62P

3-14

DSR-2000/2000P

3-5. Removal/Reattachment of the Boards

3-5-3. Removal/Reattachment of the Boards
n
Turn off the power of the unit before removing.
Tools
.
.
.
.

Torque screwdriver’s bit (for M3) :
Torque screwdriver (3kg) :
Locking compound :
Tweezers

J-6325-110-A
J-6325-400-A
7-432-114-11

Removal/Reattachment of the CP-341 board
(1) Remove the top panel. (Refer to Section 3-3.)
(2) Remove the seven connectors (blue, yellow, orange,
green, red, black, and white) on the rear panel with
tweezers.
(3) Remove the five screws (BVTT3 x 6) and remove the
rear panel in the arrow direction.

Red

White
Black
Green
Orange
Yellow
Blue

(4) Remove the fifteen screws (BVTP3 x 8) and eight
screws for connector and detach the CP-341 board by
opening the board in the arrow direction.
n
Use care not to break the terminals of capacitors, etc.
when removing the CP-341 board.
(5) Set the CP-341 board in the reverse direction of the
arrow and fix temporally it to the rear panel with the
fifteen screws.
(6) Apply a half-drop size of screw-locking compound to
each screw for connector, and tighten securely the
eight screws for connector together with the fifteen
screws.
(7) Reconnect the seven connectors disconnected in Step 2
with tweezers, using care to set the right color in the
right place.
(8) Reattach the rear panel to the unit by connecting
securely the five connectors of the CP-341 board
(CN601, CN602, CN603, CN604, and CN605) and the
three connectors of the CP-342 board (CN606, CN607,
and CN608) to the eight connectors of the MB-859
board.
(9) Fix the rear panel with the unit with the five screws.

CP-341 board

Screws
BVTT3 x 6

Screw
BVTP3 x 8
Screws
BVTP3 x 8
Screws for
connector Screws
BVTP3 x 8
Connctor panel
Screws
BVTT3 x 6

DSR-2000/2000P

CN605
CN604
CN603
CN602
CN601

CN608
CN607
CN606

CP-342 board

Connectors
(MB-859 board)

3-15

3-5. Removal/Reattachment of the Boards

Removal/Reattachment of the CP-342 board
(1) Remove the top panel. (Refer to Section 3-3.)
(2) Remove the seven connectors (blue, yellow, orange,
green, red, black, and white) on the rear panel with
tweezers.
(3) Remove the five screws (BVTT3 x 6) and remove the
rear panel in the arrow direction
Red

White
Black
Green
Orange
Yellow
Blue

(4) Remove the eight screws while supporting the CP-342
board from the rear side, and remove the
CP-342 board.
(5) Fix temporally the CP-342 board to the rear panel with
the eight screws (B3 x 6).
(6) Tighten the eight screws (B3 x 6) securely and
reconnect the seven connectors disconnected in Step 2
with tweezers, using care to set the right color in the
right place.
(7) Reattach the rear panel to the unit by connecting
securely the five connectors of the CP-341 board
(CN601, CN602, CN603, CN604, and CN605) and the
three connectors of the CP-342 board (CN606, CN607,
and CN608) to the eight connectors of the MB-859
board.
(8) Fix the rear panel with the unit using the five screws.

Screws
BVTT3 x 6

Rear panel

CN605
CN604
CN603
CN602
CN601

Connector
panel
Screws
BVTT3 x 6

3-16

Connectors
(MB-859 board)

CP-341 board

CP-342 board

CN606
CN607
Screws
B3 x 6

CN608

DSR-2000/2000P

3-5. Removal/Reattachment of the Boards

Removal/Reattachment of the DU-83 board
Serial No. 100001-100910: UC
400001-401550: CE

Removal/Reattachment of the DU-84 board
Serial No. 100001-101240: UC
400001-401550: CE

(1) Remove the DPR-136 board from the unit.
(Refer to Section 3-5-1.)
(2) Remove the DU-83 board by removing the three
screws (PWH3 x 6).
(3) Reconnect the connector (CN201) of the DU-83 board
to the connector (CN100) of the DPR-136 board and
fix the board with the three screws.
(4) Reattach the DPR-136 board to the unit. (Refer to
Section 3-5-1.)

(1) Remove the DPR-136 board from the unit.
(Refer to Section 3-5-1.)
(2) Remove the DU-84 board by removing the three
screws (PWH3 x 6).
(3) Reconnect the connector (CN1) of the DU-84 board to
the connector (CN150) of the DPR-136 board and fix
the board with the three screws.
(4) Reattach the DPR-136 board to the unit.
(Refer to Section 3-5-1.)

CN100

CN150
DPR-136 board

DPR-136 board

Screws
PWH3 x 8
CN201
DU-83 board
CN1

Screws
PWH3 x 8
DU-84 board

DSR-2000/2000P

3-17

3-5. Removal/Reattachment of the Boards

Removal/Reattachment of the DU-89 board
Serial No. 100001-101240: UC
400001-401550: CE

Removal/Reattachment of the DU-95 board
Serial No. 100001-100290: UC
400001-400300: CE

(1) Remove the DPR-136 board from the unit.
(Refer to Section 3-5-1.)
(2) Remove the DU-89 board by removing the three
screws (PWH3 x 6).
(3) Reconnect the connector (CN1) of the DU-89 board to
the connector (CN151) of the DPR-136 board and fix
them with the three screws.
(4) Reattach the DPR-136 board to the unit.
(Refer to Section 3-5-1.)

(1) Remove the APR-45 board form the unit.
(Refer to Section 3-5-1.)
(2) Remove the DU-95 board by removing the screw (B3
x 4).
(3) Reconnect the connector (CN1) of the DU-95 board to
the connector (CN61) of the APR-45 board and fix
them with the screw (B3 x 4).
(4) Reattach the APR-45 board to the unit.
(Refer to Section 3-5-1.)

APR-45 board
DPR-136 board

CN61

Screw
B3 x 4
CN151
CN1

3-18

DU-89
board

Screws
PWH3 x 8

CN1
DU-95 board

DSR-2000/2000P

3-5. Removal/Reattachment of the Boards

Removal/Reattachment of the DY-15 board

Removal/Reattachment of the EX-752 board

(1) Remove the front panel. (Refer to Section 3-3.)
(2) Disconnect the flexible card wire from the connector
(CN720) of the DY-15 board,.
(3) Remove the two screws (PWH3 x 6) and remove the
DY-15 board upward.
(4) Insert the two protrusions of the DY-15 board in the
two square holes in the chassis and fix them with the
two screws.
(5) Reconnect the flexible card wire disconnected in Step
(2).
(6) Reattach the front panel.

(1) Remove the RP-111 board from the unit. (Refer to this
section Removal/Reattachment of RP-111.)
(2) Remove the RP shield by removing the four screws
(BVTT3 x 6).
(3) Remove the EX-752 board upward.
(4) Fit the notch of the EX-752 board in the slot in the
chassis and reconnect the connector (CN300) of the
EX-752 board to the connector (CN300) of the MB859 board.
(5) Fit the two positioning holes of RP shield onto the two
protrusions on the chassis and fix the board with four
screws (BVTT3 x 6).
(6) Reattach the RP-111 board. (Refer to this section
Removal/Reattachment of the RP-111 board.)

Squre holes

DY-15 board

Flexible card wire

Positioning
holes

Screws
BVTT3 x 6

RP shield
Screws
BVTT3 x 6

Screw
PWH
3x6
Protrusions
CN720

Screw
PWH3 x 6

CN300

EX-752 board

Protrusions

Slot
CN300 (MB-85 board)

DSR-2000/2000P

3-19

3-5. Removal/Reattachment of the Boards

Removal/Reattachment of the FU-78P board
Serial No. 101241-: UC
401551-: CE

Removal/Reattachment of the FU-78R board
Serial No. 101241-: UC
401551-: CE

(1) Remove the DPR-136 board from the unit.
(Refer to section 3-5-1.)
(2) Remove the FU-78P board by removing the two
screws (PWH3 x 5).
(3) Reconnect the connector (CN11, CN12) of the FU-78P
board to the connector (CN150, CN151) of the DPR136 board and fix the board with the two screws.

(1) Remove the DPR-136 board from the unit.
(Refer to section 3-5-1.)
(2) Remove the FU-78R board by removing the two
screws (PWH3 x 5).
(3) Reconnect the connector (CN21, CN22) of the FU-78P
board to the connector (CN450, CN451) of the DPR136 board and fix the board with the two screws.

CN150
CN151

DPR-136 board

Screw
PWH3 x 5
CN12

CN11

CN451
CN450

Screw
PWH3 x 5

CN22

FU-78P board

CN21

Screw
PWH3 x 5

FU-78R board

3-20

DSR-2000/2000P

3-5. Removal/Reattachment of the Boards

Removal/Reattachment of the HP-99 board
(1) Remove the control panel. (Refer to Section 3-3.)
(2) Lift up the right/left hinge levers in the arrow direction
and bring the control frame assembly to the lateral
position, then loosen the two screws (PWH3 x 6).
(3) Disconnect the flexible card wire form the connector
(CN710) of the KY-452 board.
CN710
Control frame assembly

(4) Slide the control frame assembly in the arrow direction
to remove it.
(5) Remove the screw and release the two claws form the
rear side of the assembly and remove the KY cover.
(6) Disconnect the harness from the connector (CN2) of
the HP-99 board.
(7) Remove the two nuts to remove the HP-99 board.
n
Support the HP-99 board from the rear side when
removing the nuts.
(8) Reattach the HP-99 board in the reverse order of the
removing steps (1) to (7).

Control frame assembly

Screw
PWH3 x 6
Flexible card wire
Control frame assembly

CN2

Hinge lever

HP-99 board

Harness

Claw
Screw
PWH3 x 6

KY cover

Claw
Screw
PWH3 x 6

DSR-2000/2000P

3-21

3-5. Removal/Reattachment of the Boards

Removal/Reattachment of the IF-778 board
(DSBK-200)
(1) Remove the three screws (PWH3 x 6) of the control
frame assembly and remove the control panel assembly in the arrow direction.
Control panel assembly

(2) Remove the screw (PWH3 x 6) and release the two
claws from the rear side and remove the KY cover.
(3) Disconnect the harness from the connector (CN2) of
the IF-778 board.
(4) Remove the three screws (PWH3 x 6) to remove the
IF-778 board.
(5) Reattach the IF-778 board in the reverse order of the
removing steps (1) to (4).

Control frame assembly

IF-778 board

CN2

Screw
PWH3 x 6

Claw

Screw
PWH3 x 6

Harness
Screws
PWH3 x 6

Control frame assembly
Screw
PWH3 x 6

KY cover

Claw
Screw
PWH3 x 6

3-22

DSR-2000/2000P

3-5. Removal/Reattachment of the Boards

Removal/Reattachment of the KY-452 board
(1) Remove the control frame assembly. Refer to this
section Removal/Reattachment of the HP-99 board,
steps (1) to (4).
(2) Remove the screw (PWH3 x 6) from the rear side and
remove the KY cover.
(3) Disconnect the two flexible card wires from the
connectors (CN714 and CN713) of the KY-452 board
and also the two flexible card wires from the connectors (CN710 and CN711) of the KY-452 board with
tweezers.
(5) Remove the four screws securing the KY-452 board.
(6) Disconnect the harness from the connector (CN712)
while lifting the KY-452 board.
(7) Reattach the KY-452 board in the reverse order of the
removing steps (1) to (6).

Removal/Reattachment of the KY-452A board
(DSBK-200)
(1) Remove the three screws of the control frame assembly (PWH3 x 6) to remove the control panel assembly.
Control panel assembly

Screw
PWH3 x 6

Control frame
Harnesses

Screw
PWH3 x 6
Control frame assembly
Screw
PWH3 x 6

Flexible
card wires

CN713
CN712

CN714

CN710
CN711

Claw

Screw
PWH3 x 6
KY-452 board
Screws
KY cover PWH3 x 6

DSR-2000/2000P

Claw
Screw
PWH3 x 6

3-23

3-5. Removal/Reattachment of the Boards

(2) Remove the screw (PWH3 x 6) and release the seven
claws from the rear side and remove the KY cover.
(3) Disconnect the harnesses from the connectors (CN710
and CN711) of the KY-452A board with tweezers.
(4) Remove the four screws (PWH3 x 6) securing the
KY-452A board.
(5) Remove the KY-452A board in the arrow direction.
(6) Reattach the KY-452A board in the reverse order of
the removing steps (1) to (5).

Control frame
Harnesses

KY-452A
board
Screw
PWH
3x6

CN710
CN711

Claws

Screws
PWH3 x 6
Claws

KY cover
Claws

Claw
Screw
PWH3 x 6

3-24

DSR-2000/2000P

3-5. Removal/Reattachment of the Boards

Removal/Reattachment of the MB-859
(1) Remove the APR-45 board, VPR-62/62P board, DPR136 board, SY-278 board and SV-212 board.
(Refer to Section 3-5-1.)
(2) Remove the EX-752 board. (Refer to this section
Removal/ Reattachment of the EX-752 board.)
(3) Disconnect the harnesses from the two connectors
(CN901 and CN902) of the MB-859 board and also
disconnect the flexible card wire from the connector
(CN505).
(4) Remove the bottom panel. (Refer to Section 3-3.)
(5) Disconnect the three flexible card wires from the
connectors (CN500, CN501, CN502, CN503 and
CN504) of the MB-859 board.
(6) Remove the 10 screws to remove the MB-859 board.
(7) Reset the MB-859 board to the unit aligning properly
the connectors of the MB-859 board (CN601, CN602,
CN603, CN604, CN605, CN606, CN608, CN701,
CN702, CN703 and CN704) to the correspondent
connectors on the unit.
n
Use care not to bend the connector pins.

Screws
PWH3 x 6
Bottom
panel

Screws
PWH3 x 6

(8) Reattach the MB-859 board in the reverse order of the
removing steps (1) to (6).

Harness
connectors
Flexible
card wires

CN606
CN607
CN608
CN601
CN602
CN603
CN604
CN605

CN701
CN702
CN703
CN704

Screws
PWH3 x 6
Screws
PWH3 x 6

CN500

CN901
Screws
MB-859 board
PWH3 x 6

CN505
CN503
CN502
CN501
CN902
CN504

DSR-2000/2000P

3-25

3-5. Removal/Reattachment of the Boards

(7) Remove the three screws (B2 x 4) to remove the
mechanism deck from the unit

Removal/Reattachment of the MS-64 board
(1) Remove the top panel. (Refer to Section 3-3.)
(2) Remove the cassette compartment.
(Refer to Section 3-4.)
(3) Remove the bottom plate. (Refer to Section 3-3.)
(4) Remove the MD cover. (Refer to Section 7-2)
(5) Disconnect the four flexible card wires from the
connectors (CN1, CN2, CN3 and CN4) of the RP-111
board.
(6) Disconnect the five flexible card wires from the
connectors (CN500, CN501, CN502, CN503 and
CN504) of the MS-64 board.
CN504

CN502

Mechanism deck assembly
Positioning hole

Screws
B2 x 4

Positioning hole

RP-111 board

CN1

CN2
CN3
CN4

MS-64 board
CN501 CN503 CN500

3-26

Positioning pin

DSR-2000/2000P

3-5. Removal/Reattachment of the Boards

(8) Release the connection of connectors on the MS-64
board (CN1, CN2, CN3, CN4, CN5, CN6, CN7, CN8,
CN9, CN10, CN11, CN12, CN13 and CN19).
(9) Remove the seven screws (B2 x 4) to remove the MS64 board.
(10)Fit the two positioning holes of the MS-64 board on
the positioning pins on the MD chassis respectively
and fix the board with the seven screws.
(11)Reattach the MS-64 board in the reverse of the
removing steps (1) to (9).
Positioning hole
Screws
B2 x 4
Screw
B2 x 4

MS-64 board

CN1
CN8
CN10

Screws
B2 x 4

CN11

Removal/Reattachment of the RP-111 board
(1) Remove the top and bottom panels.
(Refer to Section 3-3.)
(2) Disconnect the four flexible card wires from the
connectors of the RP-111 board (CN1, CN2, CN3, and
CN4).
(3) Remove the four screws (PWH3 x 6).
(4) Release the connection of the two connectors (CN301,
CN302) on RP-111 board to remove the RP-111
board.
(5) Reattach the RP-111 board in the reverse order of
removing steps (1) to (4).
RP-111 board
Screws
PWH3 x 6

CN301
CN302
Screws
PWH3 x 6

CN6

CN7
CN9
Positioning
pin

CN4
Positionin
hole

CN3
CN2
CN1

Positioning pin

CN19

CN12
CN13

Flexible card wires

CN2
CN5
CN3
CN4 MS-64 board

DSR-2000/2000P

3-27

3-5. Removal/Reattachment of the Boards

Removal/Reattachment of the SE-521 board

Removal/Reattachment of the SE-522 board

(1) Remove the top panel. (Refer to Section 3-3.)
(2) Remove the cassette compartment.
(Refer to Section 3-4.)
(3) Remove the TG1 arm assembly. (Ref to Section 7-13.)
(4) Remove the loading motor assembly.
(Refer to Section 7-18.)
(5) Disconnect the flexible card wire from the connector
(CN3) of the SE-521 board.
(6) Disconnect the flexible card wire from the connector
(CN4) of the SE-521 board.
(7) Remove the screw to remove the SE-521 board.
(8) Fit the hole and the slotted hole of the SE-521 board
on the two shafts of the MD chassis and fix it with the
screw.
Tightening Torque : 0.1 N.m {1 kgf.cm}
n
Use care not to pinch the tip of the flexible card wire
of the S tension regulator assembly between the
SE-521 board and the chassis.
Place the SE-521 board under the claw of the worm
holder.

(1) Remove the top panel. (Refer to Section 3-3.)
(2) Remove the cassette compartment.
(Refer to Section 3-4.)
(3) Disconnect the two flexible cable wires from the
connectors (CN2, CN3) of the SE-522 board.
(4) Remove the two screws (P1.4 x 3.5) and remove the
SE-522 board avoiding any contacts to the T drawer
arm assembly.
(5) Fit the two positioning holes of the SE-522 board on
the positioning pins of the MD chassis, and insert the
sensors (PH1, PH2, and PH3) of the SE-522 board in
the square holes in the MD chassis.
(6) Reattach the SE-522 board in the reverse order of the
removing steps (1) to (5).
Tightening Torque : 0.1 N.m {1 kgf.cm}

(9) Reconnect the flexible card wire to the connector
(CN4) of the SE-521 board.
(10)Reconnect the flexible card wire of the S tension
regulator assembly to the connector (CN3) of the
SE-521 board.
(11)Reinstall the loading motor assembly.
(Refer to Section 7-18.)
(12)Reattach the TG1 arm assembly.
(Refer to Section 7-13.)

Positioning
hole

Screws
P1.4 x 3.5

Sensors
CN2

Sensor
SE-522 board

T drawer arm

CN3

Positioning hole

P1.4 x 3.5
SE-521 board

Connector
(CN4)
Square
holes

Connector
(CN3)

Positionin pin

Claw of
worm holder
Flexible
card wire

Flexible card wire
Square holes
Positionin pin

Flexible
card wire

3-28

DSR-2000/2000P

3-5. Removal/Reattachment of the Boards

Removal/Reattachment of the SE-525 board (LED
holder assembly)
(1) Remove the top panel. (Refer to Section 3-3.)
(2) Remove the cassette compartment.
(Refer to Section 3-4.)
(3) Remove the RMP (T1) holding assembly.
(Refer to Section 7-8.)
(4) Remove the rail assembly. (Refer to Section 7-15.)
(5) Remove the LED holder assembly from the rail
assembly.
(6) Reattach the LED holder assembly to the rail assembly.
(7) Reattach the SE-525 board in the reverse order of the
removing steps (1) to (4).
Tightening Torque : 0.1 N.m {1 kgf.cm}

(1) Remove the SE-521 board. (Refer to this section
Removal/Reattachment of the SE-521board.)
(2) Remove the screw to remove the SE-538 board.
(3) Reattach the SE-538 board in the reverse order of the
removing steps (1) and (2).
Tightening Torque : 0.1 N.m {1 kgf.cm}

SE-521 board

Positioning hole

LED holder assembly

Claw

Removal/Reattachment of the SE-538 board

P1.4 x 2
SE-538 board

Protrusion

Claw
SE-525 board

Rail assembly

SE-525 board
DSR-2000/2000P

3-29

3-5. Removal/Reattachment of the Boards

Removal/Reattachment of the SW-11/11P board

Removal/Reattachment of the SW-17 board

(1) Disconnect the two flexible card wires from the
connectors (CN720, CN730) of the SW-11/11P board
with the control panel brought to the lateral position.
(2) Remove the two screws (PWH 3 x 6) to remove the
sub panel cover.

(1) Remove the front panel. (Refer to Section 3-3.)
(2) Disconnect the flexible card wire from the connector
(CN730) of the SW-17 board.
(3) Remove the screw to remove the SW-17 board.
(4) Reattach the SW-17 board in the reverse order of the
removing steps (1) to (3).

Flexible card wires
Control frame assebly
Flexible card wire

CN730

CN720
Screw
PWH3 x 6

Screw
PWH3 x 6
SW-11/11P board

Sub panel cover

CN730
SW-17 board

Screw
PWH3 x 6

(3) Remove the two screws (PWH 3 x 6) and remove the
SW-11/11P board upward.
(4) Fit the indentation of the SW-11/11P board with the
notch of the chassis so as to connect the connectors of
SW-11/11P board (CN701, CN702, CN703 and
CN704) to the connectors of the motherboard (CN701,
CN702, CN703 and CN704).
(5) Reattach the SW-11/11P board in the reverse order of
the removing steps (1) to (3).
Control frame assembly

Notch of
chassis
CN701
(mother board)
Screw
PWH3 x 6
CN701
CN702
CN703

CN702
CN703
CN704
CN704

Notch of
chassis

Screw
Indentation
PWH3 x 6
SW-11/11P board

3-30

DSR-2000/2000P

3-5. Removal/Reattachment of the Boards

Removal/Reattachment of the VR-259 board

Removal/Reattachment of the VR-260

(1) Remove the control frame assembly. Refer to this
section Removal/Reattachment of the HP-99 board,
steps (1) to (4).
(2) Remove the screw (PWH3 x 6) and release the two
claws from the rear side, and remove the KY cover.
(3) Disconnect the flexible card wire from the connector
(CN1) of the VR-259 board.
(4) Remove the four nuts to remove the VR-259 board.
n
Support the VR-259 board from the rear side when
removing the nuts.

(1) Remove the control frame assembly. Refer to this
section Removal/Reattachment of the HP-99 board,
steps (1) to (4).
(2) Remove the screw (PWH3 x 6) and release the claws
from the rear side and remove the KY cover.
(3) Disconnect the flexible card wire from the connector
(CN1) of the VR-260 board.
(4) Remove the four nuts to remove the VR-260 board.
n
Support the VR-260 board form the rear side when
removing the nuts.

(5) Reattach the VR-259 board in the reverse order of the
removing steps (1) to (4).

(5) Reattach the VR-260 in the reverse order of the
removing steps (1) to (4).

Attached nuts

Control frame assembly
Control frame assembly

CN1

VR-259 board

VR-260 board

CN1

Claw

Flexible card wire

KY cover

Claw
Screw
PWH3 x 6

DSR-2000/2000P

KY cover

Claw
Screw
PWH3 x 6

3-31

3-6. Notes on Repair Parts

< Type B >

3-6-1. Flexible Card Wire Replacement

Removing method
Raise the portion marked “A” of the connector and release
the lock. Pull out the flexible card wire.

The following six types of flexible card wire are used in
the DSR-2000/2000P.
n
Take utmost care when handling the flexible card wires
because their life is extremely shortened by folding.

Insertion method
Insert the flexible card wire fully up to the marked line and
push up the portion marked “A” of the connector.
Flexible card wire

< Type A >
Removing method
Raise the portion marked “A” of the connector and release
the lock. Pull out the flexible card wire.
Insertion method
Insert the flexible card wire fully up to the marked line and
push up the portion marked “A” of the connector.
A

Insulation side

Connector

Unlocked status
Connector

Flexible card wire

Connector

Flexible card wire
Locked status

n
The flexible card wire has the conduction side and the
insulation side. Connect the flexible card wire after
checking for the correct side as shown.
If the condition side and the insulation side are connected
in the wrong direction, the circuit will not operate.

3-32

DSR-2000/2000P

3-6. Notes on Repair Parts

< Type C >

< Type D >

Removing method
Raise the portion marked “A” of the connector and release
the lock. Pull out the flexible card wire.

Removing method
n
Do not pull the flexible card wire before releasing the lock.

Insertion method
Insert the flexible card wire fully up to the marked line and
push up the portion marked “A” of the connector.

1. Move the portion “A” of the connector in the direction
of the arrow A to release the lock. Remove the
flexible card wire.
Insertion method
m
. Confirm that the contacting surface of the flexible card
wire is free from stain and dust.
. Confirm that the lock of the connector is already released.
. The flexible card wire has the conduction side and the
insulation side. Check the conduction side and the
insulation side before connection.

Flexible card wire

Insulation side

Connector
Unlocked status

1. Insert the flexible card wire securely to the deep end.
2. Push in the portion marked “A” of the connector in the
direction of the arrow to lock the connector. Be
careful that the flexible card wire is not slanted with
respect to the connector.

Flexible card wire

A
A
Connector
Locked status

A
A
Connector

Unlocked status
Flexible card wire

A
Locked status

DSR-2000/2000P

3-33

3-6. Notes on Repair Parts

< Type E >

< Type F >

Removing method
n
Do not pull the flexible card wire before releasing the lock.

1. Move the portion “A” of the connector in the direction
of the arrow A to release the lock. Remove the
flexible card wire.

Insertion method
m
. Confirm that the contacting surface of the flexible card
wire is free from stain and dust.
. Confirm that the lock of the connector is already released.
. The flexible card wire has the conduction side and the
insulation side. Check the conduction side and the
insulation side before connection.
1. Insert the flexible card wire securely to the deep end.
2. Push in the portion marked “A” of the connector in the
direction of the arrow to lock the connector. Be
careful that the flexible card wire is not slanted with
respect to the connector.

Connector

A
A

A
Flexible card wire
Unlocked status

A
Flexible card wire
Unlocked status
Connector

Connector

A
Flexible card wire
Locked status

3-34

DSR-2000/2000P

3-7. Replacement of Lithium Battery

3-7. Replacement of Lithium Battery
The SY-278 board has the built-in lithium battery as the
countermeasure for power failure. The lithium battery is
attached on top of IC212 (E-5). Life of the lithium battery
is about six years.
Time to exchange the battery is displayed in the time
counter display block and on the monitor display. Replace
the battery when the following message appears.

Backup battery replacement procedure
n
When replacing the battery, insert the replacement battery
with the “+” and “_” ends correctly oriented. If the
battery’s positive (+) and negative (_) terminals are
backward, physical injury or damage to peripheral equipment can be result due to explosion and or leakage of
internal materials.
1. Remove the SY-278 board. (Refer to section 3-5-1.)
2. Insert tip of a flat head (_) screwdriver in between the
battery and IC212, and remove the battery.
3. Attach the replacement lithium battery so that the
protrusion of the lithium battery is directed in the
arrow direction as shown, and the battery is firmly
secured by the four claws.

Claw
Lithium battery

Protrusion
Claw

SY-278 board

Time counter display block
Claws

Sony part number :
Type :

DSR-2000/2000P

! 1-528-749-11
M4Z28BR00SH1

IC212

3-35

3-8. Fixtures and Tools list

3-8. Fixtures and Tools list
Fig.

Part No.

Description

Uses

J-6080-029-A

Small adjustment mirror

Video tracking adjustment

J-6082-231-A

Washer mounting fixture (ø1.5)

Parts replacement

J-6082-232-A

Washer mounting fixture (ø1.2)

Parts replacement

J-6082-233-A

Washer mounting fixture (ø0.8)

Parts replacement

J-6082-234-A

Washer extracting fixture A

Parts replacement

J-6082-236-A

Washer fixture kit

Parts replacement (Set of No.2 to No.5)

J-6082-362-A

Tape guide adjustment driver

Tape guide height adjustment

J-6082-373-A

Torque cassette

FWD/REV winding torque adjustment

J-6325-110-A

Torque screwdriver‘s bit (M1.4)

Parts replacement

J-6325-380-A

Torque screwdriver’s bit (M2)

Parts replacement

J-6325-400-A

Torque screwdriver (3 kg)

Tightening screws

J-6443-710-A (CCW)

Brake torque gauge (CCW) (DJ-371)

Brake torque adjustment

J-6443-720-A (CW)

Brake torque gauge (CW) (DJ-372)

Brake torque adjustment

J-6444-930-A

Extension board (DJ-493)

Extension board for DSR-2000

J-6444-610-B

Path Adjustment Board (DJ-461)

For tape path adjustment RF envelope
detector fixture

J-6443-760-A

System control/Servo
download tool board (DJ-376)

Software version-up

3-184-527-01

Cleaning cloth

Cleaning

7-432-114-11

Locking compound

7-662-001-39

Grease SG-941(20g)

Parts replacement

8-967-999-02

Alignment tape XH2-1AST

Tape path alignment (NTSC & PAL)

8-967-999-22

Alignment tape XH5-1A2 (NTSC)

Audio/video alignment (DVCAM)

8-967-999-26

Alignment tape XH5-1AP2 (PAL)

Audio/video alignment (DVCAM for PAL)

8-967-999-31

Alignment tape XH4-1A (NTSC)

Audio/video alignment (DV)

9-919-573-01

Cleaning fluid

Cleaning

3-36

DSR-2000/2000P

3-8. Fixtures and Tools list

2 3 4

9 !/

@/ @- @=

DSR-2000/2000P

3-37

3-9. Upgrading the System/Servo CPU Program Version

3-9. Upgrading the System/Servo CPU Program Version
The DSR-2000/2000P mounts the CPU for SY and SP on the SY-278 board, CPU for SV on the SV-212
board and uses flash ROMs for stored this program.
For re-writing flash ROMs, two methods are provided.
(1) Use the fixture (DJ-376 : J-6443-760-A).
(2) Download softwares from a PC through RS-422.

3-9-1. Version Upgrade using the DJ-376
Setting of DJ-376
Write softwares into PROMs below.
Use the fixture : J-6443-760-A (DJ-376)
ROMs to be used on the fixture DJ-376:
SY/SV CPU MX27C2000DC-12 (8-759-477-94) or equivalent
SP CPU
M27C1001-70F1 (F8) (8-759-583-91) or equivalent
As these CPUs employ 16 bits data bus, 2 pieces of PROMs are required for one CPU.
Write softwares into PROMs in the 8 bit split mode. A PROM at even address side is for CN102.
A PROM at odd address side is for CN101.
(1) Insert the PROMs, in which softwares are written, into the socket on the fixture DJ-376.
(2) Set bit 1 of S101 on the fixture DJ-376 to OPEN (upper side) and the rest of bits to the board side
(lower side).
How to upgrade
(1) Remove the top panel. (Refer to Section 3-3.)
(2) Connect the fixture DJ-376, on which PROMs are installed, as follows.
CPU

Connect to DJ-376

SY CPU (IC102/SY-278)

CN1/SY-278

SP CPU (IC302/SY-278)

CN2/SY-278

SV CPU (IC119/SV-212)

CN2/SV-212

(3) Turn on the power to the set, Then, writing starts.
While writing is being executed, the LEDs of the fixture DJ-376 show the status shown below.
D102 lights:
ERASE is being executed.
D102 and D104 light: BLANK CHECK is being executed
D103 lights:
COPY is being executed.
D104 lights:
VERIFY is being executed.
(4) Only D105 (a green LED next to three red LEDs) lights, Then, writing is finished.
D105 lights:
Normal
D101 lights:
Abnormal
In an event of abnormally, suspect the cause judging from status of LEDs.
(5) Power down the set. And remove the fixture DJ-376.
(6) Turn on the power to the set, and confirm the version of upgraded CPU in the MAINTENANCE
MENU.

3-38

DSR-2000/2000P

3-9. Upgrading the System/Servo CPU Program Version

3-9-2. Version Upgrade from a PC through RS-422
Preparation
To convert the RS-232C of a PC to RS-422 (9 pin), use a conversion box or conversion board available
on the market.
Install the version upgrade application software (fup.exe) on the PC on which Windows95 or 98 is
installed.
Download the version upgrade software of CPUs to be upgrade.
How to use Fup.exe
Start up the fup.exe and then the main dialogue menu shown below appears.
Flash ROM Update
CPU
SY

Flash ROM Update - COM Setting
SV

COM Setting

File

Port
Baudrate

COM1
38400

Browse
Data Bit

VTR Status
Parity Bit
Stop Bit

Odd
1

PC Status

Start

Cancel

Main Dialogue

CPU :
COM Setting :
File :

Browse :
VTR Status :
PC Status :
Start :
Cancel :
Quit :

Cancel

Quit

Communication Setting Dialogue

Select one of SY and SV.
(Designate a target CPU to be transferred.)
The communication setting dialogue appears.
(DO NOT assign items other than Port.)
Enter a hex filename to be transferred in this field.
When a filename is selected using Browse, the selected filename appears.
Drag & Drop is supported.
The file selection menu appears.
The message from a VTR appears in this field.
This field shows a status such as “FINISH”,
The file transfer to a VTR is started. (Unless a filename is designated, it is invalid. )
The file transfer to a VTR is stopped.
The application is terminated.

Operation
Operate in the order of “Select CPU.” → “ Designate hex.filename to be transferred.” → “Press Start
button.”.
During transferring, the status is displayed in between “PC Status” and “ Start, Cancel and Quit buttons”.
The progress bar and the remaining time are displayed.

DSR-2000/2000P

3-39

3-9. Upgrading the System/Servo CPU Program Version

Message
VTR Status
Erasing flash memory.
Writing flash memory.
Completed download.
Unable to access to flash memory.
Unable to erase of flash memory.
Verify Error occurs.
Checksum error occurs.
Communication error occurs in
VTR and PC
PC Status
Trying communication with a PC.
Communication with a VTR is stopped.
Message Box
No response from a VTR
Can’t set a VTR to remote mode.
Can’t set a VTR to adjustment mode.
Can’t set a VTR to download mode.
File not found.
Can’t open a port.
A VTR interrupts communication.
VFD Display
loading XX (XX : SY, SV, SP)
complete!
incomplete!
Error91-130
Error91-430
Error91-215

Flash ROM device error, Writing error
Flash ROM erasure error
Verify-error in writing into flash memory
Checksum error in data received from a PC
Overrun, flaming, parity error

Starts at the pressing the Start button and ends until VTR
starts to erase flash memory.
A user pressed Cancel button.

When Start button is pressed, if a file is not found.
When Start button is pressed, RS-232C COM does not open.
Before transfer finishes, a VTR finishes.

Now loading
Download is completed without fail.
Download is abnormally terminated
SY flash ROM is abnormal.
(Valid only in download mode.)
SP flash ROM is abnormal.
(Valid only in download mode.)
Waiting for data sent from a PC
(Communication error between SY and KY)
Power down a VTR once.

Monitor
ALARM
Now upgrading
After version upgrade
power down once.
After the version upgrade is completed, turn off and on the power of the VTR.
(In case of upgrading the same CPU or other CPU, it is not necessary to power down.)
If properly finished, confirm that CPU versions written in the MAINTENANCE MENU are correct.
3-40

DSR-2000/2000P

Section 4
Error Messages
4-1. Alarm Display
This unit has an alarm display function.
When a problem is detected, an alarm is displayed immediately in the timer counter block. The alarm and a message
describing the countermeasure are displayed on a video monitor connected to the VIDEO OUT 3 (SUPER) or the SDI
OUTPUT 3 (SUPER) connector.
This unit has two types of alarms : one is for operators while the other is for service persons. This manual describes only
the alarms for service persons. For details of alarms for operators, refer to the operating instruction or overview in this
manual. Activating the alarm display may influence the system, such as when the reference video signal is not used.
Therefore, you can select whether or not to display the alarm from the Setup menu selection. As for Setup menu, refer to
Section 1 of this manual or to the operating instruction. However, the alarms for service persons are displayed regardless
of the Setup menu setting.

4-1-1. Alarm Display when the Main Power is
Turned On
Detection :

Checks the settings of switch
S201 on the SY-278 board and
the contents of non-volatile
memory (EEPROM).
Operation after detection : None
Display :
The alarm is displayed until
any key is pressed.

Detection :

Checks the version of the
Setup menu.
Operation after detection : The Setup menu operates
using the factory settings. The
contents of the non-volatile
memory (EEPROM) remain
unchanged. Therefore, if the
setting of the Setup menu is
not changed, the same alarm
will appear when the main
power is turned on.
Display :
The alarm is displayed until
any key is pressed.

DSR-2000/2000P

ALARM
SETT I NG HAS BEEN
CHANGED TO
X1 ED I TOR NTSC (J)
CHECK THE S201 SW I TCH
ON THE SY BOARD.

ALARM
THE SETUP MENU SOFTWARE
HAS BEEN UPGRADED.
SET THE SETUP MENU I TEMS
TO THE DES I RED SETT I NGS
OR ACT I VATE THE ’ LOAD
MENU DATA ’ (MA I NTENANCE
MENU) FUNCT I ON.

4-1

4-1. Alarm Display

Detection :

Checks that switch S101 on
the SV-212 board is set to ON.
Operation after detection : None
Display :
The alarm is displayed until
any key is pressed.

Checks that the FACTORY
USE item of the Setup menu is
changed.
Operation after detection : None
Display :
The alarm is displayed until
any key is pressed.

ALARM
THE UN I T I S I N
ADJUSTMENT MODE.
SET THE SW I TCHES OF S101
ON THE SV BOARD TO OFF.

Detection :

4-2

ALARM
SELECT I ONS OF THE SETUP
MENU’S FACTORY USE
I TEMS HAVE BEEN CHANGED.
SET THESE I TEMS TO
FACTORY PRESET VALUES.

DSR-2000/2000P

4-2. Error Codes

4-2. Error Codes
This unit has a self diagnostics function which detects
internal abnormalities. When a problem is detected, an
error code is displayed immediately in the time counter
block, and details of the error appear on the video monitor
connected to the VIDEO OUT 3 (SUPER) or the SDI
OUTPUT (SUPER) connector.
n
An error code appears in the column shown by XX-XXX
on the display.

ERROR
AN ERROR HAS BEEN
DETECTED. I NFORM SERV I CE
OF FOLLOWING CODE :
XX-XXX
PRESS EJECT KEY
TO EJECT TAPE.

When detected, some errors turn the unit to AUTO OFF.
(Refer to Section “4-2-3. Error Codes,” excluding error
code 08-032.)
This error is kept in memory even after the main power of
this unit is turned off. In other words, the error code or the
contents of the detected error appear even when the main
power of this unit is turned off and then back on again, so
this unit enters AUTO OFF mode again.
This unit enters the emergency EJECT mode when the
[EJECT] key is pressed at this moment.
[Reference]
In the emergency EJECT mode, the tape is ejected gently
by usable motor assuming that the tape is slack or a device
may be faulty.
The following message appears on the video monitor
connected to the VIDEO OUT 3 (SUPER) or the SDI
OUTPUT (SUPER) connector when this unit enters the
emergency EJECT mode.
The error code is displayed on the time counter.

DSR-2000/2000P

ERROR
TAPE I S BE I NG EJECTED.
WA I T UNT I L TH I S
I ND I CAT I ON GOES OFF.

4-3

4-2. Error Codes

The message shown to the right appears on the video
monitor connected to the VIDEO OUT 3 (SUPER) or the
SDI OUTPUT (SUPER) connector when a cassette tape is
ejected in the emergency EJECT mode.
The error code is displayed on the time counter.

The message shown to the right appears on the video
monitor connected to the VIDEO OUT 3 (SUPER) or the
SDI OUTPUT (SUPER) connector when a cassette tape
cannot be ejected with the emergency EJECT mode.
The error code is displayed on the time counter.

ERROR
AN ERROR HAS BEEN
DETECTED. I NFORM SERV I CE
OF FOLLOW I NG CODE :
XX-XXX

ERROR
TAPE CANNOT BE EJECTED.
I NFORM SERV I CE
OF FOLLOW I NG CODE :
XX-XXX

Perform Section “4-3-1. How to Take Out the Cassette
Whose Tape is Slacked (MANUAL EJECT) ” when a
cassette tape cannot be ejected with the emergency EJECT
mode.

4-4

DSR-2000/2000P

4-2. Error Codes

4-2-1. Display of Previously Detected Error Codes
When the DSR-2000/2000P detects an internal abnormality, the error code is memorized in EEPROM.
(Excluding error code 9X-XXX)
A maximum of 8 error codes detected previously, starting from the latest error code, can be displayed.
How to display the error code
1. While pressing the [DELETE], [+], and TRIM [+]
keys, press the [MENU] key.

2. Move the cursor to SERVICE SUPPORT so that the
letters are highlighted using the [AUDIO|IN],
[VIDEO|IN] keys, then press the [ENTRY] key.

3. Move the cursor to ERROR LOG so that the letters are
highlighted using the [AUDIO|IN], [VIDEO|IN]
keys, then press the [ENTERY] key.
The display changes as shown to the right, and the
error log appears.

MA I NTENANCE MENU
MENU DATA CONTROL
SERVO CHECK
SERVO ADJUST
TAPE PATH ADJUST
ELECTR I CAL ADJUST
SERV I CE SUPPORT
OTHERS

MA I NTENANCE MENU
SERV I CE SUPPORT
ERROR LOG
MANUAL EJECT
D I AGNOST I CS CONTROL

MA I NTENANCE MENU
SERV I CE SUPPORT
ERROR LOG
ERROR-08-03A
ERROR-02-674
ERROR-02-603
ERROR-08-03A
ERROR-02-674
ERROR-02-603

DSR-2000/2000P

4-5

4-2. Error Codes

4-2-2. Main Codes and Sub Codes
Main codes
The main code is a two-digit number that indicates the system which sensed the error.
Main code 0X :
Servo and tape path system error
Main code 2X :
Mechanism control system error
Main code 3X :
Sensor error
Main code 91 :
Communication system and interface system error
Main code 92 to 94 :
Sync. system error
Main code 95 :
Digital signal process system error and communication error with ICs
Sub codes
The sub code is a three-digit number. Each digit has the following meaning.
When the main code is 0X or 2X :
X

Third digit : Abnormal symptom
Second digit : Device which senses abnormality
First digit : Mode which senses abnormality.
First digit : Mode which senses abnormality.
0 : Mode cannot be identified, or mode identification is
not necessary.
1 : Cassette down mode
2 : Threading mode
3 : STOP mode
4 : F. FWD or REW mode
5 : SEARCH mode
6 : PLAY or RECORD mode
7 : STANDBY-OFF mode
8 : Unthreading mode
9 : Cassette up mode
A : Cassette out mode
(State that a cassette is ejected.)

4-6

Second digit : Device which senses abnormality
0 : Device cannot be identified, or device identification is
not necessary.
1 : Cassette up/down motor/sensor
2 : Threading motor/FG/sensor
3 : Drum motor/FG
4 : Capstan motor/FG
5 : Supply reel motor/FG
6 : Supply reel brake solenoid
7 : Takeup reel motor/FG
8 : Takeup reel brake solenoid
9 : Supply and takeup reel motor/FG
A : Tension regulator
B : Pinch solenoid
C : Reel position motor/sensor
D : Head cleaning solenoid
E : M stop solenoid
Third digit : Abnormal symptom
0 : Abnormal symptom identification is not necessary.
1 : Operation could not be completed within the specified
time.
2 : Abnormal speed detected.
3 : Tape slack detected.
4 : FG cannot be detected.
5 : FG detected.
6 : Rotating direction error detected.
7 : Excessive tension detected.
8 : Abnormal current detected.
9 : The full top or full end of a tape cannot be released.
A : Retry in progress
(Unthreading and re-threading)

DSR-2000/2000P

4-2. Error Codes

When the main code is 3X :

When the main code is from 92 to 94 :

All sub codes are 000.

When the main code is 91 :
X
X
X

Third digit : Abnormal signal
Second digit : IC to which the signal is input
First digit : CPU (microprocessor) which detects the
abnormality
. . . . . Same as the main code 91

Third digit : Abnormal symptom
Second digit :CPU (microprocessor) or IC of the
communication counterpart.
First digit : CPU (microprocessor) or IC which detects the
abnormality.
First and second digits : CPU (microprocessor) code.
1 : System control main CPU (SY-278, IC101)
2 : Keyboard u-COM (KY-452, IC5)
3 : Memory
4 : Servo main CPU (SV-212, IC1)
5 : Servo sub u-COM (DR-364, IC1)
7 : SPCON main CPU (SY-278, IC301)
8 : TC IC (SY-278, IC508)
9 : Keyboard sub u-COM (SW-11, IC204)
A : External keyboard u-COM (KY-452A, IC5)
D : DV I/F u-COM (IF-763, IC2)
E : Digital I/F u-COM (APR-45, IC651)
Third digit : Abnormal symptom (when the communication counterpart is other than memory)
1 : Abnormal checksum
2 : Abnormality of overrun
3 : Abnormal parity
4 : Abnormal framing
5 : Communication could not be completed in the specified time.

Third digit : Abnormal signal
1 : Reference frame pulse of the output signal (NSG OE)
2 : Reference track pulse of the playback side (P-TRKT)
3 : Reference frame pulse of the playback side (P-FLTT)
4 : Reference track pulse of the record side (R-TRKT)
5 : Reference frame pulse of the record side (R-FLTT)
6 : Reference track pulse of the playback side (P-TRKD)
7: Reference frame pulse of the playback side (P-FLTD)
8: Reference track pulse of the record side (R-TRKD)
9: Reference frame pulse of the record side (R-FLTD)
When the main code is 95 :
X
X
X
Second and third digits :
IC of the communication counterpart.
(The second digit indicates the communication line number and the third digit indicates
the CS number.)
First digit : CPU (microprocessor) or IC which detects the
abnormality.
. . . . . Same as the main code 91

Third digit : Abnormal symptom (when the communication counterpart is memory)
0 : Abnormality of ROM
1 : Abnormality in the external memory area
2 : Abnormality in the internal memory area
3 : Abnormality in the common memory-1 area
4 : Abnormality in the common memory-2 area
5 : Abnormality in the external serial memory-1 area
6 : Abnormality in the external serial memory-2 area
7 : Abnormality in the external serial memory-3 area
8 : Abnormality in the external serial memory-4 area
9 : Abnormality in the EEPROM area
A : Abnormality in the NVRAM area
B : Abnormality in the Hours Meter area
F : Abnormality of MIC
DSR-2000/2000P

4-7

4-2. Error Codes

4-2-3. Error Codes
Main code 0X : abnormality of servo and tape path system
1 Main code 02
Sub Detected contents
code

Operation after
detecting an
abnormality

Operable mode

Display period

058

Detected an abnormal current in the S reel motor.

AUTO OFF

068

Detected an abnormality of reel brake plunger solenoid.

EJECT
(Emergency EJECT)

Displayed until the
next cassette tape
is inserted.

078

Detected an abnormal current in the T reel motor.

0B8

Detected an abnormality of pinch plunger solenoid.

Cassette tape insertion and unthreading
are prohibited until the error is solved.

Displayed until the
error is solved.

154

Failed to detect the S reel FG by the FG check during
cassette tape insertion.

Cassette tape
will be ejected.

174

Failed to detect the T reel FG by the FG check during
cassette tape insertion.

Displayed until the
next cassette tape
is inserted.

194

Failed to detect both S and T reel FGs by the FG check
during cassette tape insertion.
AUTO OFF

EJECT
(Emergency EJECT)

254

Failed to detect the S reel FG during threading.

255

Detected the S reel FG during threading.

275

Detected the T reel FG during threading.

291

Failed to complete winding a tape.

355

Detected the S reel FG during STOP and STILL.

375

Detected the T reel FG during STOP and STILL.

395

Detected both S and T reel FGs during STOP and STILL.

402

Detected an abnormal tape speed during F. FWD and REW.

STOP

The machine operates Displayed until
normally after the error any key is
is solved.
pressed.

403

Detected slack tape during F. FWD and REW.

AUTO OFF

454

Failed to detect the S reel FG during F. FWD and REW.

EJECT
(Emergency EJECT)

474

Failed to detect the T reel FG during F. FWD and REW.

494

Failed to detect both S and T reel FGs during F. FWD and REW.

496

Detected the abnormal direction of S and T reel rotation
during F. FWD and REW.

503

Detected slack tape during search.

554

Failed to detect the S reel FG during search.

574

Failed to detect the T reel FG during search.

594

Failed to detect the S and T reel FGs during search.

596

Detected the abnormal direction of S and T reel rotation
during search.

603

Detected slack tape during PLAY and REC.

4-8

Displayed until the
next cassette tape
is inserted.

DSR-2000/2000P

4-2. Error Codes

Sub Detected contents
code

Operation after
detecting an
abnormality

Operable mode

Display period

654

Failed to detect the S reel FG during PLAY and REC.

AUTO OFF

674

Failed to detect the T reel FG during PLAY and REC.

EJECT
(Emergency EJECT)

Displayed until the
next cassette tape
is inserted.

694

Failed to detect both S and T reel FGs during PLAY and REC.

696

Detected the abnormal direction of S and T reel rotation
during PLAY and REC.

803

Detected slack tape during unthreading.

854

Failed to detect the S reel FG during unthreading.

855

Detected the S reel FG during unthreading.

875

Detected the T reel FG during unthreading.

A55

Detected the S reel FG during cassette eject.

A75

Detected the T reel FG during cassette eject.

A95

Detected both S and T reel FGs during cassette eject.

Insertion of a cassette is inhibited until the error is solved.

2 Main code 06
Sub Detected contents
code

Operation after
detecting an
abnormality

Operable mode

Display period

3A7

Detected abnomal tape tension during STOP.

AUTO OFF

4A7

Detected abnomal tape tension during F.FWD/REW.

EJECT
(Emergency EJECT)

Displayed until the
next cassette tape
is inserted.

5A7

Detected abnomal tape tension during SEARCH.

6A7

Detected the abnormal tape tension during PLAY and RECORD.

The mode at the
time of detection
is kept continued.
(If the mode is
PLAY, PLAY
continues.)
If mode is
changed to other
than PLAY and
RECORD,
machine enters
AUTO OFF.

The machine
operates normally
after the error is
solved. The PLAY
and RECORD
modes continue
but other modes
are changed to
STOP then EJECT
(Emergency EJECT).

Displayed until the
error is solved and
any key is
pressed.

Sub Detected contents
code

Operation after
detecting an
abnormality

Operable mode

Display period

042

Detected the abnormal capstan speed.

STOP

The machine
operates normally
after the error is
solved.

Displayed until
any key is
pressed.

144

Failed to detect the capstan FG by the FG check during
cassette tape insertion.

Cassette tape
will be ejected.

Displayed until the
next cassette is
inserted.

3 Main code 07

DSR-2000/2000P

4-9

4-2. Error Codes

4 Main code 08
Sub Detected contents
code

Operation after
detecting an
abnormality

Operable mode

Display period

03A

Retry (The
mechanism
unthreads once
then threads
again.)

EJECT

Displayed until the
error is solved.

AUTO OFF

EJECT

Displayed until the
next cassette is
inserted.

Sub Detected contents
code

Operation after
detecting an
abnormality

Operable mode

Display period

010

Detected abnomal position of cassette compartment.

020

Detected an abnormality of threading position sensor.

Cassette tape insertion and unthreading
are prohibited until the error is solved.

Displayed until the
error is solved.

028

Detected an abnormal current of threading motor.

221

Failed to complete threading within the specified time

AUTO OFF

224

Failed to detect the threading FG during threading.

EJECT
(Emergency EJECT)

Displayed until the
next cassette is
inserted.

821

Failed to complete unthreading within the specified time

824

Failed to detect the threading FG during unthreading.

Detected the abnormal drum speed.
Video monitor display

ERROR
DRUM SPEED ERROR
HAS BEEN DETECTED
WA I T UNT I L TH I S
I ND I CAT I ON GOES OFF.

032

The abnormal drum speed error is not solved.

5 Main code 09

. Main code 2X : Abnormality related to the mechanism control
1 Main code 20
Sub Detected contents
code

Operation after
detecting an
abnormality

Operable mode

Display period

018

Detected the abnormal current in the cassette up/down motor.

AUTO OFF

111

Failed to complete the cassette down motion within the
specified time.

EJECT
(Emergency EJECT)

Displayed until the
next cassette is
inserted.

911

Failed to complete the cassette up motion within the
specified time.

4-10

DSR-2000/2000P

4-2. Error Codes

2 Main code 21
Sub Detected contents
code

Operation after
detecting an
abnormality

Operable mode

Display period

0C8

Detected the abnormal current in the reel position motor.

AUTO OFF

EJECT
(Emergency EJECT)

OE8

Detected the abnormal current of M stop plunger solenoid.

Displayed until the
next cassette is
inserted.

1C1

Failed to complete the reel position movement within the
specified time.

Cassette tape
will be ejected.

3 Main code 22
Sub Detected contents
code

Operation after
detecting an
abnormality

Operable mode

Display period

0D8

AUTO OFF

EJECT
(Emergency EJECT)

Displayed until the
next cassette is
inserted.

Sub Detected contents
code

Operation after
detecting an
abnormality

Operable mode

Display period

STOP

PLAY, FF, EJECT

Displayed until the
error is solved and
any key is
pressed.

Detected an abnormal current of cleaning plunger solenoid.

. Main code 3X : Sensor trouble
Sub codes are all 000.

Failed to release the tape top.

Failed to release the tape end.

STOP

PLAY, REW, EJECT

Detected an abnormal current of reel shift sensor LED.

Insertion of
cassette tape is
inhibited.

Detected an abnormality of threading sensor.

Detected an abnormality of cassette compartment position
sensor.

Cassette tape insertion and unthreading
are prohibited until the error is solved.

Detected an abnormality of fan motor.

Only error is
displayed.

Detected an abnormality of cassette top/end sensor LED.

STOP

PLAY, EJECT

Detected an abnormality of tension sensor.

AUTO OFF

EJECT
(Emergency EJECT)

DSR-2000/2000P

4-11

4-2. Error Codes

Main code 91 : Abnormality of communication system or interface system
Main
code

Sub
code

Detected contents

125

Communication error between system control and keyboard (detected by SY).

130

System control detected abnormality of ROM.

131

System control detected abnormality of external memory.

132

System control detected abnormality of internal memory.

133

System control detected abnormality of common memory for SERVO.

134

System control detected abnormality of common memory for SPCON.

139

System control detected abnormality of EEPROM (IC1 on the SE-463 board).

13A

Detected abnormality in NVRAM.

13B

Detected abnormality in Resetable Hour Meter.

13C

Detected abnormality in Volume adjustment data area.

13F

Communication error to MIC.

145

Communication error between system control and servo.

175

Communication error between system control and SPCON.

195

Communication error between system control and the SW microprocessor.

1A5

Communication error between system control and external keyboard.

1D5

Communication error between system control and the DV microprocessor.

1E5

Communication error between system control and the DIF microprocessor.

215

Communication error between system control and keyboard (detected by KY).

430

Servo main detect abnormality of ROM.

431

Servo detected abnormality of external memory.

439

Detected abnormality in the servo adjustment data area.

43B

Detected abnormality in Unresetable Hours Meter.

455

Communication error between servo main and servo sub microprocessors.

539

Detected abnormality in the EQ data area.

730

SPCON detected abnormality of ROM.

731

SPCON detected abnormality of external RAM (IC313 and IC314 on the SY-278 board).

732

SPCON detected abnormality of internal RAM.

733

SPCON detected abnormality of the communication IC (IC208 on the SY-278 board) with SY.

734

SPCON detected communication error (SV-212, IC303) with SV.

Main code 92 to 94 : Abnormality of sync system
Main
code

Sub
code

Detected contents

101

System control detected abnormality in NSG OE.

702

SPCON detected abnormality in P-TRKT.

703

SPCON detected abnormality in P-FLTT.

704

SPCON detected abnormality in R-TRKT.

705

SPCON detected abnormality in R-FLTT.

407

The servo main microprocessor detected abnormality of P-FLTD.

506

The servo sub microprocessor detected abnormality of P-TRKD.

409

The servo main microprocessor detected abnormality of R-FLTD.

508

The servo sub microprocessor detected abnormality of R-TRKD.

4-12

DSR-2000/2000P

4-2. Error Codes

Main code 95 : Communication error with digital process system IC
Main
code

Sub
code

Detected contents

120

Communication error between system control and C1R MOD.

122

Communication error between system control and C1P MOD.

12A

Communication error between system control and NSG.

12C

Communication error between system control and VPRAD.

415

Communication error between servo and D1R.

416

Communication error between servo and HIF.

423

Communication error between servo and D1M.

424

Communication error between servo and D1S.

511

Communication error between drum and M1.

710

Frame communication error between SPCON and D1M.

711

Track pair communication error between SPCON and D1M.

712

Communication error between SPCON and V2P.

713

Communication error between SPCON and F1P.

714

Communication error between SPCON and SIFR (P).

715

Communication error between SPCON and SIFP.

720

Communication error between SPCON and AIFP.

730

Frame communication error between SPCON and D1R.

731

Track pair communication error between SPCON and D1R.

732

Communication error between SPCON and V2R.

733

Communication error between SPCON and F1R.

734

Communication error between SPCON and SIFR (R).

740

Frame communication error between SPCON and A1R Front.

741

Track pair communication error between SPCON and A1R Front.

742

Frame communication error between SPCON and A1R Rear.

743

Track pair communication error between SPCON and A1R Rear.

744

Communication error between SPCON and AIF-INDI.

745

Communication error between SPCON and ACTL.

750

Communication error between SPCON and IN-DSP.

751

Communication error between SPCON and REC-DSP.

752

Communication error between SPCON and PB-DSP.

753

Communication error between SPCON and OUT-DSP.

DSR-2000/2000P

4-13

4-2. Error Codes

4-2-4. Possible Causes of Errors
Possible causes of errors
Main code

02
403
503
603

574
674
803

554
654

402
454
474

1. Tape is stuck to the tape running mechanism.

2. Tape is loosely wound in the cassette.

3. Cassette tape is not confined properly.
(Cassette compartment is unlocked.)

4. Reel motor does not generate the correct torque.

5. Abnormality of reel FG

6. Tension regulator is defective.

O
O

Sub code

355
375

058
078

Possible causes

7. Cut-and-spliced tape is used.
8. Top detector and end detector are defective.

154
174
194
255
275
875
A55
A75
A95

254
854

594
694

494

496
596
696

395

3A7
4A7
5A7
6A7

O
O

9. Pinch roller has insufficient pressure against
capstan.

O
O

Check procedure for the possible causes, and the related circuit boards and devices
Possible causes

Check items and check procedure

1. Tape is stuck to the tape running
mechanism.
. Tape is dirty.
. Tape run mechanism is dirty.
. Humidity or condensation

.
.
.
.

2. Tape is loosely wound in the cassette.
. A tape which has been used for
many times, is used.
. A damaged tape is used.

. Check if tape has severe non-uniform winding.

3. Cassette tape is not confined properly.
(Cassette compartment is unlocked.)

Check that the four pins of the cassette
compartment are inserted into the holes of the
slant table.
Check that the cassette compartment retainer is
securely fastened.
↓
If a cassette compartment is unlocked when a
cassette compartment is inserted, exchange the
cassette compartment.
↓
When a cassette compartment is lock after it is
exchanged, the trouble is caused by the cassette
compartment. Otherwise the trouble is caused by
the defective drive circuit.

4-14

Related circuit boards and devices

Check if tape is stuck to tape guides or drum.
Check if foreign material is adhered to tape.
Check if tape is damaged.
Check if foreign material is adhered to tape run
mechanism and drum.

cassette compartment
SV-212 board

DSR-2000/2000P

4-2. Error Codes

Possible causes

Check items and check procedure

Related circuit boards and devices

4. Reel motor does not generate the
correct torque.
. Reel brake has mechanical defect.
. Reel brake solenoid is open.
. Reel brake solenoid drive IC is
defective.
. Reel motor is defective.
. Reel motor drive circuit is defective.
. Harness is defective.

. When the S and T reel brakes are considered
to be the cause of trouble :
Check the S and T reel brakes.
Check that the S and T reel brakes are released.
. When the S and T reel motors are
considered to be the cause of trouble :
Perform the servo adjustment.
Confirm that the servo adjustment is completed
as intended.

When the reel brake is considered to
be the cause of trouble :
SV-212 board, reel brake solenoid

5. Abnormality of reel FG
. S and T reel motor is defective.
. S and T reel FG amp is defective.

Perform the S and T reel adjustment.
Confirm that the reel FG adjustment is completed
as intended.

6. Tension regulator is defective.

Replace the tension regulator assembly.
Confirm that OK appears on display.

SV-212 board, MS-64 board,
SE-538 board

8. Top detector and end detector are
defective.

Check the tape top and tape end.
The top and end sensor must turn on and off
correctly.

When the tape top sensor is
considered to be the cause of trouble :
SE-522 board, SV-212 board,
tape top sensor LED
When the tape end sensor is consid
ered to be the cause of trouble :
SE-521 board, SV-212 board,
tape end sensor LED

9. Pinch roller has insufficient pressure
against capstan.
. Pinch roller has mechanical defect.
. Pinch solenoid is open.
. Pinch solenoid drive IC is defective.

Check the pinch roller.
Pinch roller must be pressed against the capstan
shaft correctly.

SV-212 board, pinch solenoid

When the S and T reel motor or the
S and T reel FG is considered to be
the cause of trouble :
SV-212 board, S and Treel motor

7. Cut-and-spliced tape is used.

DSR-2000/2000P

4-15

4-3. Counterneasure in an Emergency

4-3. Countermeasure in an Emergency
4-3-1. How to Take Out the Cassette Whose
Tape is Slacked (MANUAL EJECT)
(1)
(2)
(3)
(4)

Manual eject gear B (red)

Turn the power off.
Remove the top panel. (Refer to Section 3-3.)
Remove the front panel. (Refer to Section 3-3.)
Turn the manual eject gear A (red) in the arrow
direction with a phillips screwdriver while pressing the
gear. When the tape comes to slack, turn the reel table
from the front side utilizing a skewer and wind the
tape.
m
. In a case of standard cassette and M cassette :
Turn the reel table (T)
. In a case of mini cassette :
Turn the reel table (S)

(5) Repeat step (4) until each guide comes to the unthreading end position and furthermore the tape completely
returns into the cassette.
(6) Turn the manual eject gear B (red) in the arrow
direction until the cassette compartment completely
comes into cassette out state.

Skewer

Reel table (T)

Manual eject gear A (red)

4-16

DSR-2000/2000P

4-3. Countermeasure in an Emergency

4-3-2. Head Cleaning when Head Clogging
Occurs

4-3-3. Operating the VTR without A Cassette
Tape

Clean the video head as follows when the video head gets
dirty.

The VTR can be operated without a cassette tape by the
following switch setting.

Procedure to use the cleaning cassette

Switch setting

n
Use only the cleaning cassette tape as follows.
If another cleaning cassette tape is used, abnormal abrasion
or breakage of the video head could occur.

1. Remove the cassette compartment from this unit.
2. Turn on switches S101-3 and 4 of the SV-212 board.
3. Then turn on the main power.
Operating method

Cleaning cassette tapes :
DV12CL (Standard)
DVM12CL (Mini)
1. Insert the specific cleaning cassette tape in this unit.
The unit is automatically set in the PLAY mode and
the cleaning tape starts running.
Confirm that the [PLAY] key lights and the display
appears.
2. The cleaning cassette tape is automatically ejected
after running for 10 seconds.
n
Do not rewind the cleaning cassette tape to use it
again.
3. Make sure that the head is no longer dirty.
If the video head is still dirty after step 2 above, clean
the video head as follows.
Procedure to use the cleaning cloth
1. Soak the cleaning cloth with cleaning liquid and bring
it into contact lightly with the video head.
2. Turn the upper drum slowly by hand in the rotating
direction of the head (counterclockwise when viewed
from the top) to clean the video head.
m
. Never move the cleaning cloth in the vertical direction
against the video head because it may break the head.
. Turn the power switch off when cleaning the video head.

DSR-2000/2000P

Threading
While pressing the S/T reel motors, press the [STOP] key.
The upper drum rotates, threading ring rotates. The unit
enters the threading mode.
The tension arm and the threading ring move to the
specified position, then the threading is completed.
This condition in which the threading is completed is
referred to as the STOP status.
PLAY
Press the [PLAY] key.
The pinch roller is pressed against the capstan shaft to
enter the PLAY status.
When the [PLAY] key is pressed during threading, the
pinch roller is pressed against the capstan shaft to enter the
PLAY status after the threading has completed.
FF
Press the [F|FWD] key.
The pinch roller is pressed against the capstan shaft to set
the FWD.SEARCH to five-times speed.
REW
Press the [REW] key.
The pinch roller is pressed against the capstan shaft to set
REV.SEARCH to five-times speed.

4-17

4-3. Countermeasure in an Emergency

REC
While pressing the record proof sensor on the right side of
the T side reel table, press both the [PLAY] key and the
[REC] key.
The pinch roller is pressed against the capstan shaft to
enter REC status.
When the record proof sensor is released, the REC status is
released and the recorder returns to PLAY status.
Unthreading
Press the [EJECT] key.
Each guide moves to the specified position to complete the
unthreading.
Reel position selection
Press the [STANDBY] key on the control panel.
Reel position will be changed as shown below in accordance with the number of pressing the [STANDBY]
switch.
Mini

STD

n
Make sure to turn off switches S101-3 and 4 on the
SV-212 board after the adjustment.

4-18

DSR-2000/2000P

Section 5
Maintenance Menu
5-1. Menu Structure
This unit has a maintenance menu which is used for maintenance.
The maintenance menu has a layered structure through which you move to perform the various checks, settings and
adjustments using the specified menu items. Contents of the maintenance menu are displayed on the video monitor
connected to the VIDEO OUT 3 (SUPER) connector or the SDI OUTPUT 3 (SUPER) connector and the time counter of
DSR-2000/2000P.
Values in parenthesis ( ) are time counter display.
MENU, First layer

MENU, Second layer

MENU DATA CONTROL
(MENU CNT)

MENU STATUS DISPLAY (>MENU STA)
SAVE MENU DATA (>Save MENU)
LOAD MENU DATA (>Load MENU)

SERVO CHECK (SV Check)

SENSOR CHECK (>Sensor)

CASS-COMPARTMENT (>>Cass-COM)
TAPE TOP/END (>>Top/End)
HUMID [MOISTURE] (>>HUMID)
REC INHIBIT (>>REC INHI.)

MOTOR CHECK (>Motor)

S-REEL (>>S-Reel)
T-REEL (>>T-Reel)
THREADING (>>Threading)
CASS-COMPARTMENT (>>Cass-COM)
CAPSTAN (>> Capstan)
DRUM (>>Drum)
REEL POSITION (>>Reel POS.)

PLUNGER CHECK (>Plunger)

PINCH (>>Pinch)
REEL BRAKE (>>R-Brake)
M PLUNGER (>>M Plunger)
HEAD CLEANER (>>H. Cleaner)

SERVO ADJUST (SV Adjust)

S/T-REEL & CAPSTAN (>Reel & Cap.)
S-REEL ONLY (>S-Reel)
T-REEL ONLY (>T-Reel)
CAPSTAN ONLY (>Capstan)
TENSION (>Tension)

TAPE PATH ADJUST (TP Adjust)

TRACKING ADJUST (>Tracking)

MENU, Third layer

RF SWITCHING POSITION (>Switching)

DSR-2000/2000P

5-1

5-1. Menu Structure

Values in parenthesis ( ) are time counter display.
MENU, First layer

MENU, Second layer

ELECTRICAL ADJUST (EL Adjust)

PLL F0 (>PLL f0)

MENU, Third layer

EQ AUTO (>EQ auto)

DVCAM (>>DVCAM)
DV (>>DV)

EQ MANUAL ADJ (>EQ manual)

DVCAM (>>DVCAM)
DV (>>DV)
DV LP (>>DV LP)
DVCPRO (>>DVCPRO)

REC CURRENT (>REC cur)
FE CHECK (>FE check)
VOLUME ADJUST (>Vol adj)
PROCESS CHECK : OFF (>Proc check)

OFF (>>off)
DPR (>>dpr)
MAIN (>>main)
SUB (>>sub)
PRE (>>pre)

REF CHECK : OFF (>REF check)

OFF (>>off)
NON-STD (>>Non-STD)
STD (>>STD)

RP DATA INITIALIZE
SERVICE SUPPORT (Support)

ERROR LOG (>Error LOG)
MANUAL EJECT (>Manu. Eject)
DIAGNOSTICS CONTROL (>DIAG CNT)

OTHERS (Others)

5-2

CLEAR ERROR LOG (>>Clear LOG)

SOFTWARE VERSION (>Version)
KEYBOARD CHECK (>KY Check)
MEMORY DISPLAY (>MEM Check)

SY MEMORY DISPLAY (>> SY MEM.)
SV MEMORY DISPLAY (>> SV MEM.)
SP MEMORY DISPLAY (>> SP MEM.)
KY MEMORY DISPLAY (>> KY MEM.)
CM DISPLAY (>> CM DISP.)

DATA DISPLAY (>Data Check)

SP DATA DISPLAY (>>SP DATA)

DSR-2000/2000P

5-2. How to Operate Maintenance Menu
5-2-1. Location and Function of Switches
5-2-2. How to Enter the Maintenance Menu
5-2-3. How to Exit the Maintenance Menu

5-2. How to Operate Maintenance Menu
5-2-1. Location and Function of Switches
Use MENU, SET, ENTRY, AUTO EDIT, IN and OUT switches on the control panel shown below to perform the maintenance menu.
AUDIO IN TRIM+

CH-1

METER

CH-2

CH-3

MENU SET

MONITOR SELECT

CH-4

FULL/FINE

L
CH-1 CH-2 CH-3 CH-4

PHONE LEVEL REC

PULL FOR VARIABLE

LIST

MARK

PREREAD

PB/EE

SET

HOLD COUNTER SEL RESET

CHANNEL CONDITION

TRIM

PB
VIDEO

CH-1

INSERT
CH-2 CH-3

CH-4

AUDIO
ASSEMBLE

DELETE

DMC EDIT

PLAYER RECORDER

OUT

STANDBY

PREROLL

EJECT

REW

REC

EDIT

ENTRY SHIFT

MEMORY
HEADPHONES

PREVIEW

AUTO

AUTO EDIT

EDIT

REVIEW

DELETE

OUT

PLAY

F FWD

STOP
SEARCH VARIABLE

ENTRY

The maintenance menu has a layered structure through which you move to select the desired item.
[AUDIO|IN] KEY : Use this key to move in the direction of ↑ within the same layer.
[IN] KEY :
Use this key to move in the direction of ↓ within the same layer.
[DELETE] KEY : Use this key to move in the direction of ← to higher layers.
[ENTRY] KEY : Use this key to move in the direction of → to lower layers. (It is inoperative if there is no lower layer.)
To indicate depth of layer, the displayed menu items are indented on the video monitor and “>” is added to the top on the
time counter.

5-2-2. How to Enter the Maintenance Menu
1. While pressing the [DELETE] (←) key and [TRIM+] key , press the [MENU] key. The DSR-2000/2000P enters the
maintenance menu. The maintenance menu appears on the video monitor.
2. Select the desired item using the [AUDIO|IN] (↑) key and the [IN] (↓) key. The cursor shown with a white background moves to the selected item.
3. After the desired item is selected, press the [ENTRY] (→) key to designate the selected item.

5-2-3. How to Exit the Maintenance Menu
Press the [MENU] key to exit the maintenance menu.

DSR-2000/2000P

5-3

5-3. Contents of Maintenance Menu
5-3-1. Menu Data Control

5-3. Contents of Maintenance Menu
5-3-1. Menu Data Control
The MENU DATA CONTROL item provides a SETUP MENU data display and saving and loading the
SET UP MENU data.
This item is used to return the settings to their original values after maintenance is complete or ROM
upgrading is complete.
Operating procedure
1. Enter the maintenance menu.
2. Move the cursor to “MENU DATA CONTROL” which is
displayed with a white background, using the [AUDIO|IN]
(↑), [IN] (↓) keys.

3. Press the [ENTRY] (→) key.
“MENU DATA CONTROL” is selected and its lower layer
submenu appears.

4. Move the cursor displayed with a white background to a
desired item using the [AUDIO|IN] (↑), [IN] (↓) keys.
5. When an item is selected, press the [ENTRY] (→) key. The
contents of the selected item appear.
6. Press the [DELETE] (←) key to exit MENU DATA CONTROL and return to the main menu.
7. Press the [MENU] key to exit the maintenance menu.

5-4

DSR-2000/2000P

5-3. Contents of Maintenance Menu
5-3-1. Menu Data Control

(1) MENU STATUS DISPLAY
Displays the current status of the SET UP MENU data.
MENU VERSION :
Version number of the SET UP MENU
NUMBER OF ITEM : Numbers of the SET UP MENU items
CHANGED ITEM :
Numbers of the items which were
changed from the factory default
settings
DATA CHECK SUM : Data check sum
Pressing [ENTRY] (→) key displays the status of the SET UP
MENU stored in the menu bank 1 to 4.

(2) SAVE MENU DATA
This is used to temporarily save the user’s setup menu data. A
temporary saved data can be reset later.
1. The version of the current setup menu is displayed, and it is
waiting to press the [SET] key.
*
Pressing the [MENU] key returns to the main menu.

2. Press the [SET] key.
The SET UP MENU data is stored in EEPROM.
Confirm that [COMPLETE] appears and data saving is
complete.

m
. Data which has once been saved will not be deleted by turning
the main power on and off, or by upgrading the ROM version.
However, the saved data is deleted when the MS-64 board or the
EEPROM is replaced because the data is saved in the EEPROM
in the MS-64 board.
. When the SET UP MENU is upgraded by ROM’s version
upgrade, an alarm message appears after the ROM is replaced.
Either initialize the SET UP MENU or execute “LOAD MENU
DATA” when the alarm appears.
DSR-2000/2000P

5-5

5-3. Contents of Maintenance Menu
5-3-1. Menu Data Control

(3) LOAD MENU DATA
The saved data is stored as ordinary SET UP MENU data when it
is loaded.
1. The version number of the current SET UP MENU and that of
the SET UP MENU to be loaded are displayed, and it is
waiting to press the [SET] key.
*
Pressing the [MENU] key returns to the main menu.

2. Press the [SET] key.
The SET UP MENU data is stored in EEPROM.
Confirm that [COMPLETE] appears and data saving is
complete.

In the case of trouble :
Loading of the data will not start if SET UP MENU data has not
been saved or the saved SET UP MENU data contains an error.

5-6

DSR-2000/2000P

5-3. Contents of Maintenance Menu
5-3-2. Servo Check

5-3-2. Servo Check
Checks the servo system automatically or semi-automatically.
Operating procedure
1. Enter the maintenance menu.
2. Move the cursor to “SERVO CHECK” which is displayed
with a white background using the [AUDIO|IN] (↑), [IN] (↓)
keys.

3. Press the [ENTRY] (→) key.
“SERVO CHECK” is selected and its lower layer submenu
appears.
4. Move the cursor displayed with a white background to a
desired item using the [AUDIO|IN] (↑), [IN] (↓) keys.

5. Press the [ENTRY] (→) key.
The lower layer submenu appears.
6. Move the cursor displayed with a white background to a
desired item using the [AUDIO|IN] (↑), [IN] (↓) keys.
7. Press the [ENTRY] (→) key to select the desired item.
8. Press the [SET] key to execute the selected item.
9. After completing the check, press the [MENU] key to return
to the main menu.
10. To check other menus and submenus, repeat steps 4 to 9.
11. Press the [MENU] key to exit the maintenance menu.
n
If the [MENU] key is pressed while the check is in progress, the
check operation is forcibly ended and the display returns to the
main menu.

DSR-2000/2000P

5-7

5-3. Contents of Maintenance Menu
5-3-2. Servo Check

1. SENSOR CHECK
The respective items of “SENSOR CHECK” are described below :
1 CASS-COMPARTMENT
Checks the respective switches of the cassette compartment.
SW/Sensor

Applicable board

PH1
PH2
PH3
PH4

CC-85

S1
S2
S3

CC-84

S3
CC-84 board
PH1
S1
S2
PH2

PH4
PH3
CC-85 board

1. Execute the CASS-COMPARTMENT.
2. Confirm that the sensors are all OFF with no cassette inserted.

5-8

DSR-2000/2000P

5-3. Contents of Maintenance Menu
5-3-2. Servo Check

3. Insert the mini-cassette and confirm that the status of the
sensor is the monitor display shown right.

4. Insert the M-cassette and confirm that the status of the sensor
is the monitor display shown right.

5. Insert the standard cassette and confirm that the status of the
sensor is the monitor display shown right.

6. Insert the M-ADPT (Cassette adaptor for DVCPRO) and
confirm that the status of the sensor is the monitor display
shown right.

* _ _ : not care

DSR-2000/2000P

5-9

5-3. Contents of Maintenance Menu
5-3-2. Servo Check

2 TAPE TOP/END
Checks the tape-top and tape-end sensors.
Tape end sensor
(photodetector)

LED for tape sensor
(light emitter)
Tape top sensor
(photodetector)

1. Execute the TAPE TOP/END.
2. Confirm that both TOP SENSOR and END SENSOR are
[ON!].
3. Interrupt between the LED for the tape sensor (light emitter)
and the tape-top sensor (photodetector) by inserting a finger or
the like.
Confirm that the TOP SENSOR display changes from [ON!]
to [OFF] on the monitor display.

4. Interrupt between the LED for the tape sensor (light emitter)
and the tape-end sensor (photodetector) by inserting a finger
or the like.
Confirm that the END SENSOR display changes from [ON!]
to [OFF] on the monitor display.

In the case of trouble :
If the display does not change check whether the tape-top sensor or
the tape-end sensor itself is defective.
Check also the tape-top/tape-end sensor circuit (MS-64, SE-521/
522 board).
5-10

DSR-2000/2000P

5-3. Contents of Maintenance Menu
5-3-2. Servo Check

3 HUMID (MOISTURE)
Checks the HUMID (condensation) sensor.

HUMID (condensation) sensor

1. Execute the HUMID (MOISTURE).
2. Bring a cotton swab moistened with water in contact with the
HUMID sensor.
Confirm that [DRY] changes to [WET!] on the monitor
display.

3. Blow wind onto the HUMID sensor to evaporate any water.
Confirm that the display changes to [DRY] on the monitor 30
minutes later.
n
Once the HUMID sensor detects [WET!], even if make it dry
immediately, it takes 30 minutes to detect [DRY].

In the case of trouble :
If the display does not change from DRY to WET!, check whether
the HUMID sensor itself is defective.
Check also the HUMID sensor amplifier (MS-64 board).

DSR-2000/2000P

5-11

5-3. Contents of Maintenance Menu
5-3-2. Servo Check

4 REC INHIBIT
Checks the REC INHIBIT switch.

REC INHIBIT switch

1. Execute the REC INHIBIT.
2. Confirm the monitor display is as shown right.

3. Press the REC INHIBIT switch.
Confirm that ON is displayed on the monitor display.

In the case of trouble :
If OFF is not displayed, check the sensor on the MIC arm.

5-12

DSR-2000/2000P

5-3. Contents of Maintenance Menu
5-3-2. Servo Check

2. MOTOR CHECK
The respective items of “MOTOR CHECK” are described below :

1 S-REEL
Checks the S-reel motor.
1. Execute the S-REEL.
2. Press and hold the [AUDIO|IN] (↑), then [IN] (↓) keys for
one to two seconds, and release the reel brake by activating the
brake solenoid. Confirm that the S reel motor rotates clockwise and counterclockwise respectively during pressing the
[AUDIO|IN] (↑) key and [IN] (↓) key.

In the case of trouble :
If the brake solenoid does not emit the operating sound and the S
reel motor does not rotate in the specified direction even though
pressing the [AUDIO|IN] (↑) and [IN] (↓) keys, check the S reel
motor assembly and reel motor driver circuit (SV-212 and MS-64).

2 T-REEL
Checks the T-reel motor.
1. Execute the T-REEL.
2. Press and hold the [AUDIO|IN] (↑), then [IN] (↓) keys for
one to two seconds, and release the reel brake by activating the
brake solenoid. Confirm that the T reel motor rotates clockwise and counterclockwise respectively during pressing the
[AUDIO|IN] (↑) key and [IN] (↓) key.

In the case of trouble :
If the brake solenoid does not emit the operating sound and the T
reel motor does not rotate in the specified direction even though
pressing the [AUDIO|IN] (↑) and [IN] (↓) keys, check the T reel
motor assembly and reel motor driver circuit (SV-212 and MS-64).

DSR-2000/2000P

5-13

5-3. Contents of Maintenance Menu
5-3-2. Servo Check

3 THREADING
Checks the threading motor, the thread-end sensor, unthread-end
sensor and the cassette compartment.
1. Execute the THREADING.

2. Press and hold the [AUDIO|IN] (↑) key.
Confirm that the threading ring completes threading and the
message “THREAD END” appears on the monitor display.

3. Press and hold the [IN] (↓) key.
Confirm that the threading ring completes unthreading and
“UNTHREAD END” appears on the monitor display.

In the case of trouble :
If the threading motor does not rotate, or if the message
“THREAD END” does not appear even though threading is
complete, or if the message “UNTHREAD END” does not appear
on the monitor even though the unthreading is complete, check the
threading motor, the cassette compartment, the SV-212 board.
Check also the MS-64 board (the driver circuit and the threading
FG amplifier circuit) and the SE-512 board (the sensor).
5-14

DSR-2000/2000P

5-3. Contents of Maintenance Menu
5-3-2. Servo Check

4 CASS-COMPARTMENT
Check the cassette compartment motor.
1. Execute the CASS-COMPARTMENT.

2. Press the [ENTRY] (→) key.
Confirm that the cassette compartment moves down.
3. Press the [ENTRY] (→) key again, and confirm that the
cassette compartment moves up.
(The monitor display changes in the reverse order of the
steps for moving down the cassette compartment.)

In the case of trouble :
If the monitor display does not change, check the cassette
compartment motor, the SV-212 board (the sensor input circuit)
and the CC-83 board (the sensor).
DSR-2000/2000P

5-15

5-3. Contents of Maintenance Menu
5-3-2. Servo Check

5 CAPSTAN
Checks the capstan motor.
1. Execute the CAPSTAN.

2. Press the [ENTRY] (→) key.
Confirm that [FORWARD ... OK] appears on the monitor
display.

3. Press the [ENTRY] (→) key again.
Confirm that [REVERSE ... OK] appears on the monitor
display.

In the case of trouble :
If the monitor display does not change, check the capstan motor
and the capstan motor driver circuits (the SV-212 board, MS-64
board)

5-16

DSR-2000/2000P

5-3. Contents of Maintenance Menu
5-3-2. Servo Check

6 DRUM
Checks the drum motor.
1. Execute the DRUM.
2. Confirm the monitor display is as follows.
SPEED : [OK]
PHASE : [LOCK]
PG :
[EXIST]

In the case of trouble :
If the monitor display does not change, check the drum motor, the
SV-212 board (the drum motor driver circuit, the drum FG amp
circuit and the drum PG amp circuit).

DSR-2000/2000P

5-17

5-3. Contents of Maintenance Menu
5-3-2. Servo Check

7 REEL POSITION
Checks the reel position motor and the reel MINI/M/STD position
sensor.
1. Execute the REEL POSITION.

2. Confirm that the reel table moves in the order of the MINI
position → the M position → the STD position then returning
to the MINI position each time pressing the [ENTRY] (→)
key and the monitor display changes in accordance with the
move.

In the case of trouble :
If the reel table does not move or the monitor display does not
change, check the reel position motor, the reel MINI/M/STD
position sensor (the SE-522 and MS-64 boards) and reel position
motor driver circuit (the SV-212 board).

5-18

DSR-2000/2000P

5-3. Contents of Maintenance Menu
5-3-2. Servo Check

3. PLUNGER CHECK
The respective items of “PLUNGER CHECK” are described
below.

1 PINCH
Checks the pinch roller solenoid.
1. Execute the PINCH and confirm that the pinch solenoid
operates when the threading starts.
2. Press the [AUDIO|IN] (↑) and [IN] (↓) keys to confirm that
the PINCH comes to ON/OFF.
3. Press the [MENU] key to release the pinch solenoid and to
bring to the unthreading.
Doing so, the monitor display returns to the main menu.

In the case of trouble :
If the pinch solenoid does not operate, check the pinch solenoid
and the driver circuit (the SV-212 board).

DSR-2000/2000P

5-19

5-3. Contents of Maintenance Menu
5-3-2. Servo Check

2 REEL BRAKE
Checks the reel brake solenoid.
1. Execute the REEL BRAKE and confirm that the reel brake
solenoid operates.
2. Press the [AUDIO|IN] (↑) and [IN] (↓) keys to confirm that
the REEL BRAKE comes to ON/OFF.
3. Press the [MENU] key to release the reel brake solenoid.
Doing so, the monitor display returns to the main menu.

In the case of trouble :
If the reel brake solenoid does not operate, check the reel brake
solenoid and its driver circuit (the SV-212 board).

3 M PLUNGER
Checks the M plunger solenoid.
1. Execute the M PLUNGER.
2. Press the [AUDIO|IN] (↑) and [IN] (↓) keys to confirm that
the M PLUNGER comes to ON/OFF.
3. Press the [MENU] key to release the M plunger solenoid.
Doing so, the monitor display returns to the main menu.

In the case of trouble :
If the M plunger solenoid does not operate, check the M plunger
solenoid and its driver circuit (the SV-212 board).

5-20

DSR-2000/2000P

5-3. Contents of Maintenance Menu
5-3-3. Servo Adjust

5-3-3. Servo Adjust
Checks the servo system automatically or semi-automatically.
Operating procedure
1. Enter the maintenance menu.
2. Move the cursor to “SERVO ADJUST” which is displayed
with a white background using the [AUDIO|IN] (↑), [IN] (↓)
keys.

3. Press the [ENTRY] (→) key.
“SERVO ADJUST” is selected and its lower-layer submenu
appears.

4. Move the cursor displayed with a white background to a
desired item using the [AUDIO|IN] (↑), [IN] (↓) keys.
5. Press the [ENTRY] (→) key to select the desired item.
(Refer to the respective menu description for the adjustment
procedure.)
6. Press the [SET] key to execute the selected menu.
7. After completing the adjustment, press the [DELETE] (←)
key to return to the main menu.
8. To check other menus and submenus, repeat steps 4 to 7.
9. Press the [MENU] key to exit the maintenance menu.
n
If the [MENU] key is pressed while the adjustment is in progress,
the adjustment operation is forcibly ended and the display returns
to the main menu.

DSR-2000/2000P

5-21

5-3. Contents of Maintenance Menu
5-3-3. Servo Adjust

(1) S/T REEL & CAPSTAN
Executes the automatic adjustment of the S and T reels and,
capstan systems.
1. Execute the S/T REEL & CAPSTAN.
2. After completing adjustment, confirm that “COMPLETE”
appears.
Adjustment items
s reel fg adjust
s reel offset/friction
s reel torque
t reel fg adjust
t reel offset /friction
t reel torque
capstan fg adjust

In the case of trouble :
When “ADJUST INCOMPLETE” appears on the monitor display,
check the SV-212 and MS-64 boards (the reeel FG amplifier
circuit, reel motor driver circuit, capstan FG circuit and motor
driver cicuit) Check also the respective motors.

(2) S-REEL ONLY
Executes the automatic adjustment of the S reel only.
1. Execute the S-REEL ONLY.
2. After completing adjustment, confirm that “COMPLETE”
appears.
Adjustment items
s reel fg adjust
s reel offset/friction
s reel torque

In the case of trouble :
When “ADJUST INCOMPLETE” appears on the monitor display,
check the SV-212 and MS-64 boards (the reel FG amplifier circuit,
the reel motor driver circuit) and the S-reel motor.

5-22

DSR-2000/2000P

5-3. Contents of Maintenance Menu
5-3-3. Servo Adjust

(3) T-REEL ONLY
Executes the automatic adjustment of the T reel only.
1. Execute the T-REEL ONLY.
2. After completing adjustment, confirm that “COMPLETE”
appears.
Adjustment items
t reel fg adjust
t reel offset/friction
t reel torque

(4) CAPSTAN ONLY
Executes the automatic adjustment of the capstan FG only.
1. Execute the CAPSTAN ONLY.
2. After completing adjustment, confirm that “COMPLETE”
appears.
Adjustment item
capstan fg adjust

In the case of trouble :
When “ADJUST INCOMPLETE” appears on monitor display,
check the SV-212 and MS-64 boards (the capstan motor driver
circuit, the capstan FG amplifier circuit) and the capstan motor.

DSR-2000/2000P

5-23

5-3. Contents of Maintenance Menu
5-3-3. Servo Adjust

(5) TENSION
Executes the adjustment of the tape tension.
Mode
PLAY mode
Tools
DV torque cassette : J-6082-373-A
1. Remove the cassette compartment.
2. Turn on the main power and press the [EJECT] key.
n
Make sure that the cassette compartment connection cable is
not shorted to chassis when the main power is turned on.
3. Enter “MAINTENANCE MENU” and select “TENSION”
from “SERVO ADJUST” using the [AUDIO|IN] (↑), [IN] (↓)
keys.
4. Press the [ENTRY] (→) key to move to the next display.

5. When the display appears, press the [SET] key to start the
adjustment.

5-24

DSR-2000/2000P

5-3. Contents of Maintenance Menu
5-3-3. Servo Adjust

6. Wait until display changes and the menu appears as shown in
the right.

7. Set the DV torque cassette and place a weight of about 300 g
on it. Press the [STOP] key.

8. Keep pressing the [AUDIO|IN] (↑), [IN] (↓) keys until the
DV torque cassette reading agrees with the specification value
on display.
9. When adjustment is completed, press the [ENTRY] (→) key.

Specification is as indicated on the display.

DSR-2000/2000P

5-25

5-3. Contents of Maintenance Menu
5-3-3. Servo Adjust

10. The display changes as shown in the right, and the DSR-2000/
2000P enters the tension regulator magnet position check
mode.

11. If the check is completed unsatisfactorily, the display changes
as shown in the right.
12. Replace the tension regulator assembly in accordance with
message on the display.

13. If the check is completed satisfactorily, the display changes as
shown in the right.
14. Keep pressing the [AUDIO|IN] (↑), [IN] (↓) keys until the
DV torque cassette reading agrees with the specification value
on the display.
15. When adjustment is completed, press the [ENTRY] (→) key.
16. Repeat steps 14 and 15 to readjust the DV torque cassette
reading.

Specification is as indicated on the display.
17. Confirm that the DV torque cassette reading agrees with the
specification value on the display.
18. After completing step 17, press the [ENTRY] (→) key and the
DSR-2000/2000P enters the REV mode automatically.

Specification is as indicated on the display.

5-26

DSR-2000/2000P

5-3. Contents of Maintenance Menu
5-3-3. Servo Adjust

18. Keep pressing the [AUDIO|IN] (↑), [IN] (↓) keys until the
DV torque cassette reading agrees with the specification value
on the display.
19. When adjustment is completed, press the [ENTRY] (→) key.

Specification is as indicated on the display.
20. Press the [EJECT] key and remove the DV torque cassette.

21. Confirm that the message “COMPLETE” appears on the
display.

*
*

Press the [EJECT] key to return to the ADJUST menu.
When adjustment is complete, attach the cassette compartment.

DSR-2000/2000P

5-27

5-3. Contents of Maintenance Menu
5-3-4. Tape Path Adjust

5-3-4. Tape Path Adjust
Executes the adjustment of the tape path.
(1) TRACKING ADJUST
For adjustment of “TRACKING ADJUST”, refer to section 8-1,
8-2, 8-4, 8-5, 8-6, 8-7, and 8-8.
(2) RF SWITCHING POSITION
For adjustment of “RF SWITCHING POSITION”, refer to section
8-3.

5-28

DSR-2000/2000P

5-3. Contents of Maintenance Menu
5-3-5. Electrical Adjust

5-3-5. Electrical Adjust
Executes the electrical adjustment.
Operating procedure
1. Enter the maintenance menu.
2. Move the cursor to “ELECTRICAL ADJUST” which is
displayed with a white background using the [AUDIO|IN]
(↑), [IN] (↓) keys.

3. Press the [ENTRY] (→) key.
“ELECTRICAL ADJUST” is selected and its lower-layer
submenu appears.

4. Move the cursor displayed with a white background to a
desired item using the [AUDIO|IN] (↑) and [IN] (↓) keys.
5. Press the [ENTRY] (→) key to select the desired item.

DSR-2000/2000P

5-29

5-3. Contents of Maintenance Menu
5-3-5. Electrical Adjust

1. PLL F0
The PLL adjustment is described below :
1. Select “PLL F0” and the PLL adjustment is performed automatically.

2. After completing the adjustment, confirm that “COMPLETE”
appears.
3. Press the [DELETE] (←) key to return to the ADJUST menu.
4. Press the [MENU] key to exit the maintenance menu.

In the case of trouble :
If “INCOMPLETE” appears on the monitor display, check the
RP-111 board (the PLL circuit).

5-30

DSR-2000/2000P

5-3. Contents of Maintenance Menu
5-3-5. Electrical Adjust

2. EQ AUTO ADJ
The EQ AUTO adjustment is described below:
1 DVCAM
1. Select the EQ AUTO ADJ.

2. Move the cursor displayed with a white background to the
DVCAM using the [AUDIO|IN] (↑) and [IN] (↓) keys and
press the [ENTRY] (→) key.

3. After the monitor display comes out as shown right, insert the
XH5-1A2 (for NTSC) or XH5-1AP2 (for PAL) into the unit.
4. Press the [PLAY] key.
5. Confirm “COMPLETE” is displayed on the monitor.

To return to step 2, press the [DELETE] (←) key once.
To return to step 1, press the [DELETE] (←) key twice.
To return to the main menu, press the [DELETE] (←) key three
times.

In the case of trouble :
If “INCOMLETE” is displayed on the monitor;
1 Send the small length of the tape forward and repeat step 2
again.
2 If “INCOMLETE” is still displayed after performing 1,
check the RP-111 board (the EQ circuit).
DSR-2000/2000P

5-31

5-3. Contents of Maintenance Menu
5-3-5. Electrical Adjust

2 DV
1. Select the EQ AUTO ADJ.

2. Move the cursor displayed with a white background to the DV
using the [AUDIO|IN] (↑) and [IN] (↓) keys and press the
[ENTRY] (→) key.

3. After the monitor display comes out as shown right, insert the
XH4-1A into the unit.
4. Press the [PLAY] key.
5. Confirm “COMPLETE” is displayed on the monitor.

To return to step 2, press the [DELETE] (←) key once.
To return to step 1, press the [DELETE] (←) key twice.
To return to the main menu, press the [DELETE] (←) key three
times.

5-32

DSR-2000/2000P

5-3. Contents of Maintenance Menu
5-3-5. Electrical Adjust

3. EQ MANUAL ADJ
The EQ MANUAL ADJUSTMENT is described below:
[Reference]
If any errors are found in the played back picture and audio, or if
“INCOMPLETE” is displayed after completing the EQ AUTO
ADJ in the previous section, this adjustment enables to check the
status of the RF of each HEAD.
1. Select the EQ MANUAL ADJ.

2. Select the mode desired to check using the [AUDIO|IN] (↑)
and [IN] (↓) keys, and press the [ENTRY] (→) key.
3. Insert the cassette of which mode you desire to check into the
unit.
DVCAM : 15 u ADJ cassette
DV :
10 u ADJ cassette

4. Press the [PLAY] key.
5. Press the [RESET] key to display asterisk mark “*” to the
right side of the DATA: 0000.
6. Select the HEAD for checking with the [ENTRY] (→) key.
[Reference]
The HEAD selected is displayed in the ( ) on the top of the
monitor display.
In the case of DVCAM :
Pre E → Pre O → Main E → Main O → Sub E → Sub O →
Rec E → Rec O
In the case of DV :
Main E → Main O → Sub E → Sub O
7. Confirm that the DATA on the screen is 0000* through
000F*.
n
If press the [SET] key during confirmation, perform the EQ
AUTO adjustment.
DSR-2000/2000P

5-33

5-3. Contents of Maintenance Menu
5-3-5. Electrical Adjust

4. REC CURRENT
1. Selected the REC CURRENT.

2. Press the [AUDIO|IN] (↑), [IN] (↓) keys and the [DELETE]
(←), [ENTRY] (→) keys to adjust the data to “C0”.

3. Press the [SET] key to save the data.

5-34

DSR-2000/2000P

5-3. Contents of Maintenance Menu
5-3-5. Electrical Adjust

5. FE CHECK
1. Insert a blank tape.
(Press the keys in this order : [HOLD], [RESET] and [SET]
keys, to set the time counter to 00, which facilitates the
operation.)
2. Connect an oscilloscope as follows :
Check : TP404 & TP504/RP-111 board
GND : E401 & E501
TRIG : TP403
3. Select the FE CHECK.

4. Select REC using the [AUDIO|IN] (↑) key. Press the
[PLAY] and [REC] keys.
After recording for 30 to 60 seconds (time counter reading),
press the [STOP] key.
5. Playback the recorded segment and note down the waveform
level.

6. Select FE ONLY using the [AUDIO|IN] (↑) key. Press the
[VIDEO] key to select VIDEO INS. Locate the tape segment
that is recorded in step “4”, and press the [PLAY] and [EDIT]
keys to record (i.e., erase) the recorded segment for about 30
seconds.
7. Playback the segment recorded (erased) in step 6. and confirm
that the waveform level is 30% or less.

B
A

B < A x 0.3

DSR-2000/2000P

5-35

5-3. Contents of Maintenance Menu
5-3-5. Electrical Adjust

6. VOLUME ADJUST
1. Select the VOLUME ADJUST.

2. Press down all 8 AUDIO REC/PB volumes on the control
panel of the unit.
3. Set the PROCESS CONTROL SW on the sub-panel to
REMOTE and disconnect the cable from the VIDEO REMOTE on the rear panel.
4. Press the [SET] key to start the adjustment.
5. After completing the adjustment, the display returns automatically to the maintenance menu.

7. PROCESS CHECK
*

This menu is for the factory use only.

8. REF CHECK
*

This menu is for the factory use only.

5-36

DSR-2000/2000P

5-3. Contents of Maintenance Menu
5-3-5. Electrical Adjust

9. RP DATA INITIALIZE
1. Select the RP DATA INITIALIZE.

2. As “RP DATA INITIALIZE” will be displayed on the screen,
press the [SET] key when initializing the adjusted data.
n
After initialization, be sure to perform the following three
adjustments in Section “5-3-5. Electrical Adjust.”
1. PLL F0
2. EQ AUTO ADJ
4. REC CURRENT

DSR-2000/2000P

5-37

5-3. Contents of Maintenance Menu
5-3-6. Service Support

5-3-6. Service Support
Displays the error codes and error contents which occurred in the
past and provides the diagnosis.
Operating procedure
1. Enter the maintenance menu.
2. Move the cursor to “SERVICE SUPPORT” which is displayed
with a white background using the [AUDIO|IN] (↑), [IN] (↓)
keys.

3. Press the [ENTRY] (→) key.
“SERVICE SUPPORT” is selected and its lower layer submenu appears.

4. Move the cursor displayed with a white background to a
desired item using the [AUDIO|IN] (↑), [IN] (↓) keys.
5. Press the [ENTRY] (→) key to select the desired item.
(Refer to the respective menu description for the check
procedure.)
6. After completing the check, press the [MENU] key to return
to the main menu.
7. To check other menus and submenus, repeat steps 4 to 6.
8. Press the [MENU] key to exit the maintenance menu.

5-38

DSR-2000/2000P

5-3. Contents of Maintenance Menu
5-3-6. Service Support

1. ERROR LOG
The errors which occurred in the past are displayed.
(The latest eight maximum errors are displayed.)

The latest error is displayed on the top.
n
The servo system errors only are stored here. The ERROR-91, 92,
93, 94 and 95 are not stored.

2. MANUAL EJECT
For the operating procedure of how to take out a tape when the
EJECT is inoperable, refer to section 4-3.

3. DIAGNOSTICS CONTROL
1 CLEAR ERROR LOG
Clears the error history from the ERROR LOG.

DSR-2000/2000P

5-39

5-3. Contents of Maintenance Menu
5-3-7. Others

5-3-7. Others
Enables to check the software version, keyboard and others.
Operating procedure
1. Enter the maintenance menu.
2. Move the cursor to “OTHERS” which is displayed with a
white background using the [AUDIO|IN] (↑), [IN] (↓) keys.

3. Press the [ENTRY] (→) key.
“OTHERS” is selected and its lower layer submenu appears.

4. Move the cursor displayed with a white background to a
desired item using the [AUDIO|IN] (↑), [IN] (↓) keys.
5. Press the [ENTRY] (→) key to select the desired item.
(Refer to the respective menu description for the check
procedure after execution.)
6. After completing the check, press the [MENU] key to return
to the main menu.
7. To check other menus and submenus, repeat steps 4 to 6.
8. Press the [MENU] key to exit the maintenance menu.

5-40

DSR-2000/2000P

5-3. Contents of Maintenance Menu
5-3-7. Others

(1) SOFTWARE VERSION
Displays the model information and software version numbers.
SY
SP
SV
DR
KY
SW
EXT

: Version of IC102 on the SY-278 board.
: Version of IC302 on the SY-278 board.
: Version of IC119 on the SV-212 board.
: Version of IC301 on the SV-212 board.
: Version of IC5 on the KY-452 board.
: Version of IC204 on the SW-11 board.
: Version of IC5 on the KY-452A board.
(When DSBK-200 is installed.)
DVIO : Version of IC2 on the IF-763 board.
(When DSBK-190 is installed.)
DIF
: Version of IC651 on the APR-45 board.
MENU : Version of the setup menu.
Press the [ENTRY] key to display the version below.
V2
: Version of the DU-84 and DU-89 boards on the
DPR-136 board.
NSG
: Version of IC1013 on the VR-62 board.
AIF
: Version of the DU-83 board on the DPR-136 board.
SIFP
: Version of IC70 and IC71 on the DPR-136 board.
SIFR
: Version of IC655, IC700, IC701, IC750 and IC751 on
the DPR-136 board.
ACTL : Version of IC62 on the APR-45 board.
*

The message NONE appears for the EXT and DVIO when the
optional board is not installed in the DSR-2000/2000P.
Contents which are shown in the time counter display can be
changed using the [AUDIO|IN] (↑), [IN] (↓) keys.
Press the [DELETE] (←) key or the [MENU] key to return to
the maintenance menu.

(2) MEMORY DISPLAY
*

Factory use only.

(3) DATA DISPLAY
*

Factory use only.

DSR-2000/2000P

5-41

Section 6
Periodic Inspection and Maintenance
6-1. Periodic Inspection List
The following table shows the reference parts replacement time which is not the warranty time of parts.
Refer to the following table to establish the periodic inspection schedule which realizes the full performance and
function of a unit and to extend life of a tape. The actual parts replacement period depend on the operating
environment and conditions of a unit.
: Part replace
Inspection items

: Check (Adjustment) O : Cleaning
Hours meter

Inspection time (Hours)
2000

4000

6000

Item

Part No.

Name

Menu No.

Drum assembly

A-8323-775-A

DEH-16A-R

H02

Pinch solenoid

A-8279-203-

Pinch Solenoid assembly

H02

Brake solenoid

1-454-930-21

Solenoid plunger

H02

Reel motor (T)

8-835-636-51

DC motor (SRD14A/J-RP)

H02

Reel motor (S)

8-835-637-51

DC motor (SRD15A/J-RP)

H02

Loading motor

A-8279-202-

LD Motor assembly

H02

8000

Tape drive system blocks

Reel sift motor

A-8279-204-

RS motor assembly

H02

T reel brake shoe

A-8324-480-

Brake (T) assembly

H02

S reel brake shoe

A-8324-481-

Brake (S) assembly

H02

Head cleaner solenoid

1-454-942-31

Plunger solenoid

H02

M stop solenoid

1-454-932-11

Plunger solenoid

H02

Capstan motor

8-835-619-51

DC motor (SCD16A/J-RP)

H02

Pinch roller

A-8279-044-

Pinch limiter assembly

H02

Guide roller T2

A-8279-024-

Shuttle (R) assembly

H02

Tape path system blocks
O

Guide roller T3

A-8279-026-

T drawer arm assembly

H02

Guide roller T4

A-8279-400-

TG-8 arm assembly

H02

Guide roller S2

A-8279-023-

Shuttle (L) assembly

H02

Guide roller S3

A-8323-655-

Tension regulator assembly

H02

Guide roller S4

A-8279-399-

TG-1 arm assembly

H02

Tape running surface
(including tape cleaner)

——

Head cleaner

X-3605-655-1

HC roller assembly

A-8323-659-

MIC holder assembly

O
O
O
O

Others
Cassette memory terminal

H01: OPERATION HOURS

DSR-2000/2000P

H02 : DRUM RUNNING HOURS

H02

H03 : TAPE RUNNING HOURS

6-1

6-2. Hours Meter

6-2. Hours Meter
The hours meter data is displayed on the video monitor and time counter display area. Periodic inspection and part replacement are recommended to be performed using the hours meter reading.
1. Hours Meter Display Contents
Menu number

Item

Contents

H01

OPERATION HOURS

Accumulated hours of power on

H02

DRUM RUNNING HOURS

Accumulated hours of drum rotation

H03

TAPE RUNNING HOURS

Accumulated hours of tape running

H04

THREADING COUNTER

Number of times of threading

H12

DRUM RUNNING HOURS

Accumulated hours of drum rotation (reset enabled)

H13

TAPE RUNNING HOURS

Accumulated hours of power on (reset enabled)

H14

THREADING COUNTER

Number of times of threading (reset enabled)

2. How to Display Hours Meter Information
(1) Press the [MENU] key on the control panel.
The menu list and contents as shown above appear.
(2) Press the [MENU] key again to exit the menu display.
MENU

CH-1

METER

CH-2

CH-3

SET

MONITOR SELECT

CH-4

FULL/FINE

L
CH-1 CH-2 CH-3 CH-4

PHONE LEVEL REC

PULL FOR VARIABLE

LIST

MARK

PREREAD

PB/EE

SET

HOLD COUNTER SEL RESET

CHANNEL CONDITION

TRIM

PB
VIDEO

CH-1

INSERT
CH-2 CH-3

CH-4

AUDIO
ASSEMBLE

DELETE

DMC EDIT

PLAYER RECORDER

OUT

STANDBY

PREROLL

EJECT

REW

REC

EDIT

ENTRY SHIFT

MEMORY
HEADPHONES

PREVIEW

AUTO

EDIT

REVIEW

OUT

PLAY

F FWD

STOP
SEARCH VARIABLE

6-2

DSR-2000/2000P

6-2. Hours Meter

3. How to Reset Hours Meter
The menus H12, H13 and H14 can be reset by the following procedure.
(1) Set the switch S101-1 on the SV-212 board to ON (upper).
(2) Press the [MENU] key on the control panel. The menu list
appears.

(3) Turn the JOG dial to move the asterisk (*) mark and select
either H12 or H13 or H14. (Display example on right side
shows H12 selected.)

HOUR ME T E R
H01 : OP E HOURS
H02 : D R UM HOU RS
H03 : T A P E HOU RS
H04 : T H RED COU N T
* H12 : D R UM HOU R S R
H13 : T A PE HOU R S R
H14 : T HRE D C OU NT R
001 : P - R OL L T I ME
00
002 : C H A R A H - P OS
00
003 : C H A R A V - P OS
00
004 : S Y N C HR ON I ZE
00

- 748
- 130
- 261
- 386
- 130
- 261
0
- 5 S
00
01
ON

ITE M - H 12
DRUM R U N N I N G HOURS
( RE S E T T A B LE )
13 0 HOURS

(4) While pressing the [SEARCH] key, turn the JOG dial to
set “0 HOURS”.

ITE M - H 12
DRUM R U N N I N G HOURS
( RE S E T T A B LE )
0 HOURS

(5) Press the [SET] key on the control panel to save the reset
data.

SETUP MENU
NOW SAV I N G . . .

(6) Set the switch S101-1 on the SV-212 board to OFF (lower).

DSR-2000/2000P

6-3

6-3. Maintenance upon Completion of Repair

6-3. Maintenance upon Completion of
Repair
Perform the following maintenance work regardless of the
operating hours of the unit, after repairing it.
1. Video head cleaning
(Refer to section 6-3-1 for cleaning procedure.)
2. Tape running path cleaning
(Refer to section 6-3-2 for cleaning procedure.)
n
After a unit is cleaned, insert a cassette after cleaning fluid
is dried completely.

6-3-1. Video Head Cleaning Procedure

6-3-2. Tape Running Path Cleaning
Clean the tape guide, drum, capstan, pinch roller, tape
cleaner and other parts which contact with video tape, with
cleaning cloth moistened with cleaning fluid.
m
. Be careful of the tape cleaner during cleaning because it
has sharp edge.
. After cleaning, wipe off moisture using a dry cleaning
cloth.
. The tape cleaner is not used for Serial No.
100911 - 101390 : UC
401551 - 401850 : CE
The set of above serial number, provided ARM
ASSY, TG1 (A-8279-399-C) for repair parts to
stabilize the tape path.

Bring a cleaning cloth moistened with cleaning fluid in
contact with the head tip gently, and rotate the drum slowly
with hand for cleaning.

Cleaning cloth
Drum

Serial No. 100911 - 101390: UC
401551 - 401850: CE

: Cleaning area

Tape cleaner
(Sharp edge)
Video head

m
. Never move the cleaning cloth in vertical direction with
respect to the drum rotation (up and down with respect to
the drum) during cleaning.
. After cleaning, wipe off moisture using a dry cleaning
cloth.
. Turn off the main power before cleaning a unit.

Serial No. 100001 - 100910, 101391 - : UC
400001 - 401550, 401851 - : CE

6-4

: Cleaning area

DSR-2000/2000P

6-3. Maintenance upon Completion of Repair

6-3-3. Cassette Compartment Entrance
Cleaning
Clean the area around the cassette guide of the front panel
and entire surface of the stage of the cassette compartment
as shown using cleaning cloth moistened with cleaning
fluid.

6-3-4. Cassette Compartment Shaft Cleaning
Turn the gear (red) in the arrow direction until you can see
the shaft. Clean the shaft with a cleaning cloth moistened
with a cleaning fluid.
Gear (red)

Shaft

n
Remove the cassette compartment when cleaning a unit to
prevent foreign materials from dropping into a unit.

Entire surface of stage
(Cleaning)

Cassette compartment

6-3-5. Cassette Guide Assembly Cleaning
Clean the rear block of the cassette guide assembly with a
cleaning cloth moistened with a cleaning fluid.

Rear block of the cassette
guide assembly
Cassette guide area
(Cleaning)

Front panel block

DSR-2000/2000P

6-5

Section 7
Replacement of Mechanical Parts
7-1. General Information on Parts Replacement and Adjustment
7-1-1. Preparation Before Starting Parts Replacement
. Remove the ornamental parts as needed.
. When replacing parts or performing mechanical adjustment, remove the cassette compartment from the
DSR-2000/2000P not so far as specified. (Refer to section 3-4.)
. When the connector of the cassette compartment is removed, the protection circuit starts functioning.
Refer to section “4-3-3. Operating the VTR without a Cassette Tape.” to operate the DSR-2000/2000P
without the cassette compartment.

7-1-2. Drum Assembly
. The drum assembly is a periodic replacement part. The drum should be replaced in accordance with the
periodic replacement list.
. The drum assembly must be replaced in the following cases :
(1) When the video heads are worn out so that the proper tape-to-head contact is lost and recording and
playback cannot be performed correctly;
(2) When the rabbet guide of the lower drum is worn out so that the correct RF envelope cannot be
obtained even after adjusting the tape path to optimize the tracking.
(3) When the rabbet guide or tape running surface of the lower drum is damaged;
(4) If the drum rotation is abnormal and the VTR does not work properly due to noise or jitter.

7-1-3. Grease
Be sure to use only the authorized grease.
If grease other than the authorized one is used, major malfunctions may result due to differences in grease
viscosity and its ingredients.
If grease containing dirt is used, the shafts and bearings may be damaged and major malfunctions may
result.
Use the following grease for the DSR-2000/2000P :
Grease (SG941 (20 g)) : 7-662-001-39
. Do not apply grease to any parts other than the specified parts.
. Apply just enough grease to cover a coating on the surface.
Wipe off any grease that oozes out into the surrounding parts with gauze or a soft cloth.

DSR-2000/2000P

7-1

7-1. General Information on Parts Replacement and Adjustment

7-1-4. Tightening Torque and Handling of Washers
1. Screwdrivers and Tightening Torque of Screws
Many M1.4 and M2 screws are used in the DSR-2000/2000P.
Be sure to use the authorized tools to loosen and tighten them.
In addition, use a torque screwdriver to tighten the screws with the specified tightening torque.
Torque screwdriver bit (for M 1.4) :
Torque screwdriver bit (for M 2) :
Hexagon bit (for torque screwdriver) :
Torque screwdriver (for 3 kgf.cm) :
Tightening torque
For M1.4 screw :
For M2 screw :

J-6325-110-A
J-6325-380-A
J-6326-120-A
J-6325-400-A

0.1 N.m (1.0 kgf.cm)
0.2 N.m (2.0 kgf.cm)

[Reference]
The DSR-2000/2000P uses many small screws that easily fall inside the machine when removing and reassembling parts. To avoid this risk, magnetize the screwdriver bit slightly enough to prevent small screws from
falling into the machine. However, when installing the drum assembly, never use a magnetized screwdriver.
2. Stop Washer and E ring
Do not use old stop washers and E rings that have been removed.
Always use new stop washers and E ring to attach the parts.
Stop washer (1.5) :
Stop washer (2.3) :
E ring (2.3) :
Cotter polyethylene washer :
Polyslider washer (Ø2.0) :

3-669-465-01
3-669-596-01
7-624-105-04
3-321-813-01
3-701-437-01

How to Remove the Stop Washers and E ring
(a) Use the following fixtures to remove stop washers and E ring.
Washer extracting fixture (A) : J-6082-234-A
n
. Be careful not to drop the stop washers and E ring inside the DSR-2000/2000P.
. Be careful not to let tools touch other parts, especially the drum.
How to Attach the Stop Washers
Use the following tools to attach stop washers :
Washer mounting fixture Ø1.5 : J-6082-231-A
Washer mounting fixture Ø1.2 : J-6082-232-A
Washer mounting fixture Ø0.8 : J-6082-233-A

Washer mounting ficture

Stop washer

(a) Insert a stop washer to the tip of the washer
mounting fixture.
(b) Set the thin tip of the mounting fixture
perpendicularly to the top of the shaft to
which the stop washer is to be installed.
(c) Press the thick portion of the fixture downward to install the stop washer onto the shaft.
7-2

Stop washer

DSR-2000/2000P

7-2. Drum Replacement

7-2. Drum Replacement
Outline
Replacement
Removing the MD cover
Disconnecting the connectors
Removing the head cleaner assembly
Replacing the drum assembly
Reattaching the head cleaner assembly
Reconnecting the connectors
Reattaching the MD cover
Cleaning the heads and tape running surface
Adjustment after replacement
Tape path adjustment
RF switching position adjustment
EQ adjustment
Note
Take care not to damage the tape guides around the drum assembly, tape running
surface on the drum, video heads of the drum assembly and so on when replacing
the drum assembly.
Basic knowledge
Besides the periodic replacement, replace the drum assembly in the following cases.
. When no proper RF waveform can be obtained even if tracking adjustment is
performed.
. When the damaged tape running surface on the drum cannot be recovered.
Preparations
1.
2.
3.
4.
5.
6.

Set the unit into the unthreading end status.
Power off the unit.
Remove the top plate. (Refer to Section 3-3.)
Remove the bottom plate. (Refer to Section 3-3.)
Remove the right side plate. (Refer to Section 3-3.)
Remove the cassette compartment assembly. (Refer to Section 3-4.)

Tool
.
.
.
.

Cleaning cloth :
Cleaning fluid :
Torque screwdriver bit (for M1.4) :
Torque screwdriver (for 3 kgf.cm) :

DSR-2000/2000P

3-184-527-01
9-919-573-01
J-6325-110-A
J-6325-400-A

7-3

7-2. Drum Replacement

Replacement
1. Removing the MD cover
(1) Put the unit left side facing down.
(2) Push the two claws on the upper side of the
MD cover in the direction of the arrow as
shown in the figure to remove the lock.
(3) While removing the two claws on the lower
side of the MD cover from the square holes
on the chassis, remove the MD cover from
the square hole on the right side chassis.

Claw
Claw
MD cover

Claw
Claw

Square hole

2. Disconnecting the connectors
Disconnect the five flexible card wires from the
connector (CN10) on the MS-64 board and four
connectors (CN1, CN2, CN3 and CN4) on the
RP-111 board located on the rear side of the
chassis.
n
Be careful not to suffer injury at hand by chassis
during the disconnection.

Flexible card wire

CN1
RP-111 board
CN2
CN3
CN4

CN10

7-4

MS-64 board

DSR-2000/2000P

7-2. Drum Replacement

3. Removing the head cleaner assembly
(1) Disconnect the harness connector from the
connector (CN12) on the MS-64 board with
tweezers.
(2) Remove the two screws, and remove the head
cleaner assembly in the direction of the
arrow.

P1.4 x 3.5
Head cleaner assembly

P1.4 x 3.5

CN12

4. Replacing the drum assembly
(1) Remove the three screws, and remove the
drum assembly from the MD chassis.
n
Take care not to contact the drum assembly
to the peripheral tape guides.

P1.4 x 3.5 c
P1.4 x 3.5 a
Positioning hole
P1.4 x 3.5 b
Positioning hole

(2) Clean the installation surfaces of a new drum
assembly and MD chassis with a cleaning
cloth moistened with cleaning fluid.
(3) Put the five flexible card wires into the hole
on the MD chassis, and align the two positioning pins on the MD chassis with the holes
of the drum assembly.
(4) While moving the drum assembly in the
direction of the arrow (counterclockwise
direction), tighten the three screws in the
order of a, b, c.
Tightening torque : 0.1 N.m {1 kgf.cm}

Drum assembly
Cleaning

Positioning pin
Cleaning
Hole

Positioning pin

DSR-2000/2000P

7-5

7-2. Drum Replacement

5. Reattaching the head cleaner
assembly
(1) Align the positioning hole of the head cleaner
assembly with the positioning pin on the MD
chassis, and reattach it with the two screws.
Tightening Torque : 0.1 N.m {1 kgf.cm}
(2) Reconnect the harness to the connector
(CN12) on the MS-64 board.
n
. Use care not to contact the head cleaner
assembly with the tape running surface on the
drum.
. Do avoid touching the HC roller assembly with
bave hands.

6. Reconnecting the connectors
Reconnect the flexible card wires to the connector
(CN10) on the MS-64 board, and four flexible
card wires to the connectors (CN1, CN2, CN3
and CN4) on the RP-111 board.
m
. Be careful not to insert the flexible card wire
obliquely.
. Do insert the flexible card wire straight and
securely as far as it will go.
. Take care not to fold the flexible card wire.
This shortens the life of the flexible card wire.

P1.4 x 3.5
Iron core
Head cleaner assembly
HC roller assembly
P1.4 x 3.5

Positioning hole
Positioning pin

Positioning hole
CN12

Positioning pin

Flexible card wire

CN1
RP-111 board
CN2
CN3
CN4

CN10

7-6

MS-64 board

DSR-2000/2000P

7-2. Drum Replacement

7. Reattaching the MD cover
(1) Insert the MD cover into the unit through the
big square hole of the right side panel of the
chassis.
(2) Fit the two claws in the lower side of the MD
cover in the square holes and let the two
upper-side claws catch the side panel to fix
the MD cover in the unit.

Claw
Claw
MD cover

Claw

8. Cleaning the heads and tape running
surface
Clean the tape running surfaces of the drum and
video heads with cleaning cloth moistened with
cleaning fluid.

Claw

Adjustment after replacement
9. Tape path adjustment
(Refer to Section 8-2.)

Square hole

10. RF switching position adjustment
(Refer to Section 8-3.)
11. EQ adjustment
(Refer to Section 5-3-5.)

DSR-2000/2000P

7-7

7-3. S/T Brake Assembly Replacement

7-3. S/T Brake Assembly Replacement
Outline
Replacement
Removing the MD cover.
Moving the S/T reel tables
Removing the L push plate (only when replacing the T-side brake assembly)
Removing the MIC assembly (only when replacing the T-side brake assembly)
Removing the reel cover
Replacing the brake assembly
Checking and adjusting the brake torque
Reattaching the reel cover
Reattaching the MIC assembly (only when replacing the T-side brake assembly)
Reattaching the L push plate (only when replacing the T-side brake assembly)
Reattaching the MD cover
Note
. Prepare a new cotter polyethylene washer when replacing the brake assembly.
Cotter polyethylene washer (1.5) : 3-321-813-01
. Be careful not to lose the polyslider washer between the base plate and the MIC
assembly.
. When replacing the T-side brake assembly, prepare a new stop washer for mounting the MIC assembly.
Stop washer (1.5) : 3-669-465-01 x 1 (for mounting the MIC assembly)
Preparation
1.
2.
3.
4.
5.
6.

Set the unit to the unthreading end status.
Power off the unit.
Remove the top panel. (Refer to Section 3-3.)
Remove the bottom panel. (Refer to Section 3-3.)
Remove the right side panel. (Refer to Section 3-3.)
Remove the cassette compartment. (Refer to Section 3-4.)

Tools
.
.
.
.
.
.
.
.
.
.

Brake torque gauge (CCW) :
Brake torque gauge (CW) :
Torque screwdriver’s bit (for M1.4) :
Torque screwdriver’s bit (for M2) :
Torque screwdriver (for 3 kgf.cm) :
Washer extracting fixture (A) :
Washer mounting fixture Ø1.5 :
Cleaning cloth :
Cleaning fluid :
Tweezers

7-8

J-6443-710-A
J-6443-720-A
J-6325-110-A
J-6325-380-A
J-6325-400-A
J-6082-234-A
J-6082-231-A
3-184-527-01
9-919-573-01

DSR-2000/2000P

7-3. S/T Brake Assembly Replacement

Replacement
1. Removing the MD cover
Remove the MD cover. (Refer to Section 7-2.)
2. Moving the S/T reel tables
Turn the reel shift motor gear by a finger to bring
the S/T reel tables to the standard cassette
position.
(Refer to Section 7-19.)

P1.4 x 3.5
L push plate

3. Removing the L push plate (only when
replacing the T-side brake assembly)
Remove the two screws to remove the L push
plate.
4. Removing the MIC assembly (only
when replacing the T-side brake
assembly)
Remove the MIC assembly.
(Refer to Section 7-19.)
5. Removing the reel cover
Remove the screw, and then release the two claws
to remove the reel cover S or T.

P1.4 x 3
Reel cover S
P1.4 x 3
Reel cover T

Claw

DSR-2000/2000P

Claw

7-9

7-3. S/T Brake Assembly Replacement

6. Replacing the brake assembly
(1) Remove the cotter polyethylene washer and
remove the brake assembly and the brake
springs S/T.
n
Use care to prevent the brake spring from
flying off when removing.
The polyslider washer located under the
brake spring may come off together with the
brake spring, therefore be careful not to lose
it.
If it comes off, return it in place.

Cotter polyethylene washer
Brake assembly (S)
Brake shoe
Brake spring (S)
Cotter polyethylene
washer

Polyslider washer

Brake shoe
Brake assembly (T)
Reel table (T)

Cleaning
Brake spring (T)

(2) Wipe the contact surface on the reel table
against the brake assembly with a cleaning
cloth moistened with cleaning fluid.
(3) Join the brake spring to a new brake assembly as shown in the figure and fit it on the
reel motor shaft.
n
Avoid touching the brake shoe when replacing.
(4) Attach a new cotter polyethylene washer

7. Checking and adjusting the brake torque
(1) S reel brake torque
Check the S reel brake torque meets the
specification below by turning the knob of
the brake torque gauge (CW) in the A
direction a turn in 1 to 3 seconds.
Tightening Torque : 7.5 ± 0.5 m N.m
{75 ± 5 gf.cm}
(2) T reel brake torque
Check the T reel brake torque meets the
specification below by turning the knob of
the brake torque gauge (CCW) in the B
direction a turn in 1 to 3 seconds.
Tightening Torque : 7.5 ± 0.5 m N.m
{75 ± 5 gf.cm}

Polyslider
washer
Reel table (S)
Cleaning
c
a

b
c

Brake spring
hook on portion b

b
a

Brake spring
hook on portion b

Brake torque gauge (CW)

A
Reel table (S)

Brake torque gauge (CCW)
B

Reel table (T)

(3) Failing satisfaction of the specification,
readjust by changing the positon that the
brake spring hooks on.
. If the torque is high, hook the brake spring
on the c portion.
. If the torque is low, hook the brake spring
on the a portion.
7-10

DSR-2000/2000P

7-3. S/T Brake Assembly Replacement

8. Reattaching the reel cover
(1) Align the reference hole in the reel cover
with the pin in the reel motor, and hook the
two claws.
(2) Fix the reel cover S or T with the screw.
After fixing, apply screw locking compound.
Tightening Torque : 0.1 N.m {1 kgf.cm}

P1.4 x 3
Reel cover S
P1.4 x 3
Reel cover T

Claw

Reference
hole

Claw Reference
hole
Claw

9. Reattaching the MIC assembly (only
when replacing the T-side brake
assembly)
Reattach the MIC assembly.
(Refer to Section 7-19.)

Claw

10. Reattaching the L push plate (only
when replacing the T-side brake
assembly)
Reattach the L-push plate with the two screws
with the two holes in the L push plate aligned
with the two protrusions on the RLR assembly.
Tightening Torque : 0.1 N.m {1 kgf.cm}

P1.4 x 3.5
L push plate

11. Reattaching the MD cover
Reattach the MD cover. (Refer to Section 7-2.)

Protrusion

DSR-2000/2000P

7-11

7-4. Brake Solenoid Replacement

7-4. Brake Solenoid Replacement
Outline
Replacement
Removing the MD cover
Disconnecting the connector
Removing the brake assembly
Replacing the brake solenoid
Reattaching the brake assembly
Reconnecting the connector
Reattaching the MD cover
Checking the performance
Note
Prepare a new stop washer when replacing the brake solenoid.
Stop washer (1.5) : 3-669-465-01 x 1
Preparation
1.
2.
3.
4.
5.
6.

Tools
.
.
.
.
.
.

Torque screwdriver’s bit (for M1.4) :
Torque screwdriver’s bit (for M2) :
Torque screwdriver (for 3 kgf.cm) :
Washer extracting fixture (A) :
Washer mounting fixture Ø1.5 :
Tweezers

7-12

J-6325-110-A
J-6325-380-A
J-6325-400-A
J-6082-234-A
J-6082-231-A

DSR-2000/2000P

7-4. Brake Solenoid Replacement

Replacement
1. Removing the MD cover
Remove the MD cover. (Refer to Section 7-2.)
2. Disconnecting the connector
Disconnect the harness from the connector (CN9)
on the MS-64 board located on the back side of
the MD chassis with tweezers.
n
Be careful not to suffer injury at hand by chassis
during the disconnection.
3. Removing the brake assembly
(1) Remove the three screws securing the brake
assembly.
(2) Pull out the harness of the solenoid from the
square hole in the left side of the chassis with
the brake assembly lifted up.

P1.4 x 3.5
P1.4 x 3.5
Brake assembly

P1.4 x 3.5

Harness

Chassis

Hole

CN9

DSR-2000/2000P

7-13

7-4. Brake Solenoid Replacement

4. Replacing the brake solenoid
Serial No. 100911-: UC
401551-: CE
(1) Remove the two screws and remove the
solenoid from the brake base assembly.
n
During this operation, the two washers come
off together with the two screws, and further
the compressed coil spring comes off from
the iron core of the solenoid. Be careful not
to lose them.

Solenoid

Compression spring
Iron core

Brake slider assembly
Brake base assembly
W2.6

P2.6 x 2.8

(2) Widen slightly the clearance shown in the
brake slider assembly figure by a finger to
remove the iron core of the solenoid.
n
Applying an excessive force may cause
deformation of the brake slider assembly.

Brake slider assembly

Spring pin

(3) Reattach an iron core pin of a new solenoid to
the brake slider assembly following the same
step (2).
(4) After fitting the compressed coil spring
removed in step (1) on the iron core, insert
the iron core in a new solenoid.
(5) Fix temporally the solenoid positioning as
shown in the figure to the brake base assembly with the two screws and two washers.
(6) Ensure that the compressed coil spring is
placed between the upper and lower plates of
the brake slider assembly (within the double
headed arrow) as shown in the figure.
(7) Adjust the solenoid position to satisfy the
specification of the clearance between the
slide shaft and the slotted hole in the brake
base assembly under the condition that the
iron core is fully pulled in, and tighten
securely the two screws.
Tightening Torque : 0.5 N.m {5 kgf.cm}
(8) Reattach the brake slider assembly to the
brake base assembly with a new stop washer.

Solenoid iron core

Widen a little in the downward direction

Spring pin

Brake slider assembly

ific

ati

.5±

0.1

Slide shaft

7-14

DSR-2000/2000P

7-4. Brake Solenoid Replacement

4. Replacing the brake solenoid
Serial No. 100001-100910: UC
400001-401550: CE
(1) Remove the two screws and remove the
solenoid from the brake base assembly.
n
During this operation, the two washers come
off together with the two screws, and further
the compressed coil spring comes off from
the iron core of the solenoid. Be careful not
to lose them.

Solenoid

Compression spring
Iron core
Brake slider assembly

Brake base assembly
W2.6

P2.6 x 2.8

(2) Remove the stop washer shown in the brake
slider assembly figure.
(3) Widen slightly the clearance shown in the
brake slider assembly figure by a finger to
remove the iron core of the solenoid.
n
Applying an excessive force may cause
deformation of the brake slider assembly.
(4) Reattach an iron core pin of a new solenoid to
the brake slider assembly following the same
step (3).
(5) After fitting the compressed coil spring
removed in step (1) on the iron core, insert
the iron core in a new solenoid.
(6) Fix temporally the solenoid positioning as
shown in the figure to the brake base assembly with the two screws and two washers.
(7) Ensure that the compressed coil spring is
placed between the upper and lower plates of
the brake slider assembly (within the double
headed arrow) as shown in the figure.
(8) Adjust the solenoid position to satisfy the
specification of the clearance between the pin
of the solenoid iron core and the slotted hole
in the brake base assembly under the condition that the iron core is fully pulled in, and
tighten securely the two screws.
Tightening Torque : 0.5 N.m {5 kgf.cm}
(9) Reattach the brake slider assembly to the
brake base assembly with a new stop washer.

DSR-2000/2000P

Stop washer
Brake slider assembly

Widen a little in the upward direction
Spring pin

Solenoid iron core

Spring pin

Brake slider assembly

Brake base pin
Sp

ific

ati

0.4

7-15

7-4. Brake Solenoid Replacement

5. Reattaching the brake assembly
(1) Insert the harness of the brake assembly in a
square hole on the left side of the chassis to
bring it to the back side of the unit.
(2) Fit the slotted hole shown in the brake
assembly figure on the pin on the brake
release plate and further more fit the hole and
slotted hole in the brake base assembly on the
two reference pins of the MD chassis respectively, and fix it with the three screws.
Tightening Torque : 0.1 N.m {1 kgf.cm}

P1.4 x 3.5
P1.4 x 3.5

Brake assembly
Slotted hole

P1.4 x 3.5

Brake base assembly
Harness

Slotted hole
Hole

6. Reconnecting the connector
(1) Draw out the harness of the brake solenoid to
bring it to the back side of the unit with
tweezers.
(2) Reconnect the harness to the connector
(CN9) on the MS-64 board.
Chassis

7. Reattaching the MD cover
Reattach the MD cover. (Refer to Section 7-2.)
8. Checking the performance
(1) Power on the unit and press the [DEL],
[TRIM+], [MENU] keys simultaneously to
activate the maintenance menu.
(2) Following the pop-up menu in the maintenance menu, enter SERVO CHECK,
PLUNGER CHECK, REEL BRAKE in order
and select REEL BRAKE.
(3) Check that the brake solenoid ON/OFF
switches smoothly by presing the
[AUDIO|IN] key and the [IN] key.

7-16

Hole
CN9
Pin of break release plate
Reference pins

DSR-2000/2000P

7-5. Pinch Roller Replacement

7-5. Pinch Roller Replacement
Outline
Replacement
Removing the pinch limiter assembly.
Reattaching the pinch limiter assembly.
Adjustment after replacement
Checking the tape path adjustment
Note
. The pinch roller is a part of the pinch limiter assembly, therefore replace the pinch
limiter assembly itself when the pinch roller needs to be replaced.
. Prepare a new stop washer when replacing the pinch roller assembly.
Stop washer (1.5) : 3-669-465-01
Preparation
1.
2.
3.
4.

Set the unit to the unthreading end status.
Power off the unit.
Remove the top panel. (Refer to Section 3-3.)
Remove the cassette compartment. (Refer to Section 3-4.)

Tools
.
.
.
.
.
.

Washer extracting fixture (A) :
Washer mounting fixture Ø1.5 :
Cleaning cloth :
Cleaning fluid :
Grease (SG-941) :
Tweezers

DSR-2000/2000P

J-6082-234-A
J-6082-231-A
3-184-527-01
9-919-573-01
7-662-001-39

7-17

7-5. Pinch Roller Replacement

Replacement
1. Removing the pinch limiter assembly
Remove the stop washer and remove the pinch
limiter assembly.
n
During this operation, if the compressed coil
spring comes off together with the assembly,
return the spring in place.
2. Reattaching the pinch limiter
assembly
(1) Wipe a pinch roller in a new pinch limiter
assembly with a cleaning cloth moistened
with cleaning fluid.
(2) Wipe the shaft on the MD chassis with a
cleaning cloth moistened with cleaning fluid.
(3) Apply grease about the quarter size of a tip of
a cotton swab, to two portions of the shaft
marked in the figure.
(4) Fit the hole in the pinch limiter assembly on
the shaft on the MD chassis, while fitting the
slotted hole in the pinch limiter assembly on
the shaft on the pinch solenoid assembly, and
fix it with a new stop washer (1.5).

Stop washer

Cleaning
Pinch limitter
assembly

Compression coil
spring
Shaft
Grease
Pinch solenoid
assembly

Adjustment after replacement
3. Checking the tape path adjustment
(Refer to Section 8-4.)

7-18

DSR-2000/2000P

7-6. Elevator Cam Replacement

7-6. Elevator Cam Replacement
Outline
Replacement
Removing the pinch limiter assembly
Replacing the elevator cam
Reattaching the pinch limiter assembly
Adjustment after replacement
Chacking the tape path adjustment
Note
Prepare two kinds of new stop washers when replacing the elevator cam.
Stop washer (1.5) : 3-669-465-01 x 1 (for mounting the pinch limiter assembly)
Stop washer (2.3) : 3-669-596-01 x 1 (for mounting the elevator cam)
Preparation
1.
2.
3.
4.

Set the unit to the unthreading end status.
Power off the unit.
Remove the top panel. (Refer to Section 3-3.)
Remove the cassette compartment. (Refer to Section 3-4.)

Tools
.
.
.
.
.
.

Washer extracting fixture (A) :
Washer mounting fixture Ø1.5 :
Cleaning cloth :
Cleaning fluid :
Grease (SGL-941) :
Tweezers

DSR-2000/2000P

J-6082-234-A
J-6082-231-A
3-184-527-01
9-919-573-01
7-662-001-39

7-19

7-6. Elevator Cam Replacement

Replacement
1. Removing the pinch limiter assembly
Remove the pinch limiter assembly.
(Refer to Section 7-5.)
2. Replacing the elevator cam
(1) Lift off the compressed coil spring from the
shaft on the MD chassis.
(2) Remove the stop washer and remove the
elevator cam.
(3) Wipe the shaft on the MD chassis with a
cleaning cloth moistened with cleaning fluid.
(4) Fit the elevator cam on the shaft on the
chassis with the intermittent portion of the
elevator cam joined to the intermittent
portion of the No.7 gear as shown in the
figure.
(5) Apply grease about the quarter size of a tip of
a cotton swab, to two portions of the shaft
shown in the figure.
(6) Reattach the elevator cam with a new stop
washer (2.3).
(7) Fit the compressed coil spring on the shaft.

Elevator cam
No.7 gear

Intermittent
portion

Compression coil spring

Stop washer 2.3

Elevator cam

Shaft
Grease

Intermittent portion

3. Reattaching the pinch limiter
assembly
Reattach the pinch limiter assembly.
(Refer to Section 7-5.)

No.7 gear

Adjustment after replacement
4. Checking the tape path adjustment.
(Refer to Section 8-4.)

7-20

DSR-2000/2000P

7-7. Pinch Solenoid Assembly Replacement

7-7. Pinch Solenoid Assembly Replacement
Outline
Replacement
Removing the pinch limiter assembly.
Disconnecting the connector.
Replacing the pinch solenoid assembly.
Reconnecting the connector.
Reattaching the pinch limiter assembly.
Adjustment after replacement
Checking the tape path adjustment
Note
Without removal/reattachment of the pinch limiter assembly, the pinch solenoid
assembly cannot be replaced.
Therefore prepare a new stop washer for replacing the pinch limiter assembly.
Stop washer (1.5) : 3-669-465-01 x 1
Preparation
1.
2.
3.
4.

Set the unit to the unthreading end status.
Power off the unit.
Remove the top panel. (Refer to Section 3-3.)
Remove the cassette compartment. (Refer to Section 3-4.)

Tools
.
.
.
.
.

Torque screwdriver’s bit (for M1.4) :
Torque screwdriver (for 3 kgf.cm) :
Washer extracting fixture (A) :
Washer mounting fixture Ø1.5 :
Tweezers

DSR-2000/2000P

J-6325-110-A
J-6325-400-A
J-6082-234-A
J-6082-231-A

7-21

7-7. Pinch Solenoid Assembly Replacement

Replacement
1. Removing the pinch limiter assembly
Remove the pinch limiter assembly.
(Refer to Section 7-5.)
2. Disconnecting the connectors
Disconnect the harness from the connector (CN2)
on the MS-64 board with tweezers.

P1.4 x 3.5
Pinch slider assembly
Pinch solenoid assembly

Harness

3. Replacing the pinch solenoid
assembly
(1) Remove the two screws with the pinch slider
assembly drawn into the arrow direction and
lift off the pinch solenoid assembly.
(2) Align two holes in a new pinch solenoid
assembly with the two positioning pins on the
MD chassis respectively.
(3) Reattach the pinch solenoid utilizing the two
screws with the pinch slider assembly drawn
in the arrow direction.
Tightening Torque : 0.1 N.m {1 kgf.cm}

Positioning pins

CN2
MS-64 board

4. Reconnecting the connector
Reconnect the harness to the connector (CN2) on
the MS-64 board with tweezers.
5. Reattaching the pinch limiter
assembly
Reattach the pinch limiter assembly.
(Refer to Section 7-5.)
Adjustment after replacement
6. Checking the tape path adjustment
(Refer to Section 8-4.)

7-22

DSR-2000/2000P

7-8. Reel Motor (T) Assembly Replacement

7-8. Reel Motor (T) Assembly Replacement
Outline
Replacement
Removing the MD cover
Disconnecting the connector
Moving the S/T reel tables
Removing the L push plate
Removing the MIC assembly
Removing the RMP (T1) retainer assembly
Replacing the reel motor (T) assembly
Reattaching the RMP (T1) retainer assembly
Reattaching the MIC assembly
Reattaching the L push plate
Reconnecting the connector
Checking the performance
Reattaching the MD cover
Adjustment after replacement
T-REEL ONLY adjustment
TENSION adjustment
Tape path adjustment
Note
Without removal/reattachment of the MIC assembly, the reel motor (T) assembly
cannot be replaced. Prepare a new stop washer when reattaching the MIC assembly.
Stop washer (1.5) : 3-669-465-01 x 1
Use care not to lose the polyethylene washer between the base plate and the MIC
assembly.
Preparation
1.
2.
3.
4.
5.
6.

DSR-2000/2000P

7-23

7-8. Reel Motor (T) Assembly Replacement

Tools
.
.
.
.
.
.
.

Torque screwdriver’s bit (for M1.4) :
Torque screwdriver’s bit (for M2) :
Torque screwdriver (for 3 kgf.cm) :
Washer extracting fixture (A) :
Washer mounting fixture Ø1.5 :
Cleaning cloth :
Cleaning fluid :

J-6325-110-A
J-6325-380-A
J-6325-400-A
J-6082-234-A
J-6082-231-A
3-184-527-01
9-919-573-01

Replacement
1. Removing the MD cover
Remove the MD cover. (Refer to Section 7-2.)
2. Disconnecting the connector
Disconnect the flexible card wire from the
connector (CN6) on the MS-64 board located on
the back side of the MD chassis.

MS-64 board
T reel motor assembly
flexible card wire

Connector (CN6)

3. Moving the S/T reel tables
Turn the reel shift motor gear by a finger and
bring the S/T reel tables to the standard cassette
position.
(Refer to Section 7-19.)
4. Removing the L push plate
Remove the L push plate. (Refer to Section 7-3.)
5. Removing the MIC assembly
Remove the MIC assembly.
(Refer to Section 7-19.)
6. Removing the RMP (T1) retainer
assembly
(1) Remove the screw (a) with the T-drawer arm
assembly drawn lightly in the arrow direction.
(2) Remove the screw (b) and remove the RMP
(T1) retainer assembly.

7-24

P1.4 x 3.5 (a)

RMP retainer (T1) assembly
P1.4 x 3.5 (b)
T drawer arm assembly

DSR-2000/2000P

7-8. Reel Motor (T) Assembly Replacement

7. Replacing the reel motor (T) assembly
(1) Remove the two screws (a, b) securing the
slide shaft and remove the reel motor (T)
assembly.
(2) Extract the slide shaft from the reel motor (T)
assembly.
(3) Wipe the shaded portion in the figure with a
cleaning cloth moistened with cleaning fluid.
(4) Apply grease about the quarter size of a tip of
a cotton swab, to the center of the shaded
portion.
(5) Wipe the slide shaft with dry cloth such as
gauze, and then insert it in a hole of a new
reel motor T assembly.
n
Use extreme care not to scratch the shaft and
hole during extracting and inserting operation.

b K2 x 4

Reel moter (T) assembly

a K2 x 4

Slide shaft

Shaft

Flexible card wire

(6) Insert a shaft located on the back side of the
reel motor (T) assembly in the slot in the RS
plate assembly.
(7) Insert the flexible card wire in the square hole
in the MD chassis.
(8) Tighten the screw a and next b to reattach
the slide shaft.
Tightening Torque : 0.1 N.m {1 kgf.cm}

Slot

RS plate assembly
Square hole

DSR-2000/2000P

Cleaning

7-25

7-8. Reel Motor (T) Assembly Replacement

8. Reattaching the RMP (T1) retainer
assembly
(1) Fit the two positioning holes in the RMP (T1)
retainer assembly on the two positioning pins
on the MD chassis.
(2) Tighten the two screws to fix the RMP (T1)
retainer assembly while drawing lightly the T
drawer arm assembly in the arrow direction.

P1.4 x 3.5 (a)
Positioning hole
RMP retainer (T1) assembly
P1.4 x 3.5 (b)
T drawer arm assembly

Positioning hole

9. Reattaching the MIC assembly
Reattach the MIC assembly.
(Refer to Section 7-19.)
10. Reattaching the L push plate
Reattach the L push plate. (Refer to Section 7-3.)
11. Reconnecting the connector
Reconnect the flexible card wire to the connector
(CN6) on the MS-64 board located on the back
side of the MD chassis.
m
. Be careful not to insert the flexible card wire
obliquely.
. Do insert the flexible card wire straight and
securely as far as it will go.
. Take care not to fold the flexible card wire.
This shortens the life of the flexible card wire.

Positioning pin

12. Checking the performance
Check the S/T reel tables move smoothly by
turning the reel shift motor gear by a finger.
13. Reattaching the MD cover
Reattach the MD cover. (Refer to Section 7-2.)
Adjustment after replacement
14. T-REEL ONLY adjustment
(Refer to Section 5-3-3.)
15. TENSION adjustment
(Refer to Section 5-3-3.)
16. Tape path adjustment
(Refer to Section 8-2.)

7-26

DSR-2000/2000P

7-9. Reel Motor (S) Assembly Replacement

7-9. Reel Motor (S) Assembly Replacement
Outline
Replacement
Removing the MD cover
Disconnecting the connector
Moving the S/T reel tables
Removing the RMP (S1) retainer assembly
Replacing the reel motor (S) assembly
Reattaching the RMP (S1) retainer assembly
Reconnecting the connector
Checking the performance
Reattaching the MD cover
Adjustment after replacement
S-RELL ONLY adjustment
TENSION adjustment
Tape path adjustment
Preparation
1.
2.
3.
4.
5.
6.

Tools
.
.
.
.
.

Torque screwdriver’s bit (for M1.4) :
Torque screwdriver’s bit (for M2) :
Torque screwdriver (for 3 kgf.cm) :
Cleaning cloth :
Cleaning fluid :

DSR-2000/2000P

J-6325-110-A
J-6325-380-A
J-6325-400-A
3-184-527-01
9-919-573-01

7-27

7-9. Reel Motor (S) Assembly Replacement

Replacement
1. Removing the MD cover
Remove the MD cover. (Refer to Section 7-2.)

Connector (CN11)

2. Disconnecting the connector
Disconnect the flexible card wire from the
connector (CN11) on the MS-64 board located on
the back side of the MD chassis.
3. Moving the S/T reel tables
Turn the reel shift motor gear by a finger and
bring the S/T reel tables to the standard cassette
position. (Refer to Section 7-19.)
MS-64 board

S reel motor assembly
flexible card wire

4. Removing the RMP (S1) retainer
assembly
(1) Remove the screw (a) with the S tension
regulator arm assembly drawn lightly in the
arrow direction.
(2) Remove the screw (b), then remove the RMP
(S1) retainer assembly.

S tension regulator arm
assembly

Screw (a)
P1.4 x 3.5 (a)
P1.4 x 3.5 (b)
RMP retainer
(S1) assembly

7-28

DSR-2000/2000P

7-9. Reel Motor (S) Assembly Replacement

5. Replacing the reel motor (S) assembly
(1) Remove the two screws (a, b) securing the
slide shaft and remove the reel motor (S)
assembly.
(2) Extract the slide shaft from the reel motor (S)
assembly.
(3) Wipe the shaded portion in the figure with a
cleaning cloth moistened with cleaning fluid.
(4) Apply grease about the quarter size of a tip of
a cotton swab, to the center of the shaded
portion.
(5) Wipe the slide shaft with dry cloth such as
gauze, and then insert it in a hole of a new
reel motor S assembly.
n
Use extreme care not to scratch the shaft and
hole during extracting and inserting operation.
(6) Insert a shaft located on the back side of the
reel motor (S) assembly in the slot in the RS
plate assembly.
(7) Insert the flexible card wire in the square hole
in the MD chassis.
(8) Tighten the screw a and next b to reattach
the slide shaft.
Tightening Torque : 0.1 N.m {1 kgf.cm}

DSR-2000/2000P

Reel motor (S) assembly
Slide shaft

a K2 x 4

b K2 x 4
Reel motor (S)
assembly

Shaft
Flexible card wire

Square hole
Slot
RS plate assembly
Cleaning
MD chassis

7-29

7-9. Reel Motor (S) Assembly Replacement

6. Reattaching the RMP (S1) retainer
assembly
(1) Fit the two positioning holes in the RMP (S1)
retainer assembly on the two positioning pins
on the MD chassis.
(2) Tighten the two screws to fix the RMP (S1)
retainer assembly while drawing lightly the S
tension regulator arm assembly in the arrow
direction.

S tension regulator arm
assembly

Screw (a)

7. Reconnecting the connector
Reconnect the flexible card wire to the connector
(CN11) on the MS-64 board located on the back
side of the MD chassis.
m
. Be careful not to insert the flexible card wire
obliquely.
. Do insert the flexible card wire straight and
securely as far as it will go.
. Take care not to fold the flexible card wire.
This shortens the life of the flexible card wire.
8. Checking the performance
Check the S/T reel tables move smoothly by
turning the reel shift motor gear by a finger.

P1.4 x 3.5 (b)

P1.4 x 3.5 (a)
Positioning holes

RMP retainer
(T1) assembly

Positioning pins

9. Reattaching the MD cover
Reattach the MD cover. (Refer to Section 7-2)
Adjustment after replacement
10. S-REEL ONLY alignment
(Refer to Section 5-3-3.)
11. TENSION alignment
(Refer to Section 5-3-3.)
12. Tape path adjustment
(Refer to Section 8-2.)

7-30

DSR-2000/2000P

7-10. M Stop Solenoid Assembly Replacement

7-10. M Stop Solenoid Assembly Replacement
Outline
Replacement
Removing the MD cover
Removing the stopper driving plate (M) assembly
Replacing the M stop solenoid assembly
Reattaching the stopper driving plate (M) assembly
Reattaching the MD cover
Preparation
1.
2.
3.
4.

Set the unit to the unthreading end status.
Power off the unit.
Remove the bottom panel. (Refer to Section 3-3.)
Remove the right side panel. (Refer to Section 3-3.)

Tools
.
.
.
.

Torque screwdriver’s bit (for M1.4) :
Torque screwdriver’s bit (for M2) :
Torque screwdriver (for 3 kgf.cm) :
Screw locking compound :

DSR-2000/2000P

J-6325-110-A
J-6325-380-A
J-6325-400-A
7-432-114-11

7-31

7-10. M Stop Solenoid Assembly Replacement

Replacement
1. Removing the MD cover.
Remove the MD cover. (Refer to Section 7-2.)

P1.4 x 3.5

P1.4 x 3.5
Stopper driving plate (M) assembly

2. Removing the stopper driving plate
(M) assembly
(1) Disconnect the harness of the M stop solenoid assembly from the connector (CN8) on
the MS-64 board.
(2) Remove the two screws and remove the
stopper driving plate (M) assembly.

Connector (CN8)

3. Replacing the M stop solenoid
assembly
(1) Remove the two screws to remove the
stopper driving plate (M) assembly.
(2) Extract the compressed coil spring from the
iron core of the plunger solenoid removed in
step (2) and fit the spring on a new solenoid
iron core.

P2 x 2

Stopper driving plate

Plunger solenoid

Compression spring
Iron core

7-32

DSR-2000/2000P

7-10. M Stop Solenoid Assembly Replacement

(3) Fit the two notches of the stopper driving
plate on both ends of the iron-core pin, then
temporary reattached the stopper driving
plate to the plunger solenoid by the two
screws.
(4) In a state of plunger solenoid current is on,
slide the stopper driving plate to satisfy the
speficication. And tighten securely the two
screws.
Tightening Torque : 0.2 N.m {2 kgf.cm}
(5) Ensure the stopper driving plate returns to the
original position after being pressed in the
arrow direction and released.

P2 x 2

Hole for
screw

Hole for
screw
Stopper
driving plate

Specification:
1.5±0.1 mm

Pins

4. Reattaching the stopper driving plate
(M) assembly
(1) Move the shaft b on the M stopper (T)
assembly and the shaft c on the M stopper (S)
assembly toward the drum by a finger.
(2) Insert the projection located on the back side
of the stopper driving plate (M) assembly in
the slotted hole in the MIC drive (M) assembly. Fit the two slotted holes in the stopper
driving plate (M) assembly shown in the
figure on the shafts on M stopper (T) and (S)
assemblies, and then fix it on the MD chassis
with the two screws.
Tightening Torque : 0.1 N.m {1 kgf.cm}
(3) Ensure that the M stopper (T) and (S) assemblies and MIC drive (M) assembly move
smoothly with the iron core of the solenoid
drawn in the pulled-in direction.
(4) Reconnect the harness of the M stop solenoid
to the connector (CN8) on the MS-64 board.

Plunger solenoid

Shaft b Shaft c

M stopper (T) assembly
P1.4 x 3.5

M stopper (S) assembly
P1.4 x 3.5
Stopper driving plate (M) assembly
Slotted hole

Projection
MIC driving (M)
assembly

MIC driving (M) assembly
slotted hole
Shaft c

Shaft b

Connector (CN8)

5. Reattaching the MD cover
Reattach the MD cover. (Refer to Section 7-2.)

DSR-2000/2000P

7-33

7-11. S Tension Regulator Assembly Replacement

7-11. S Tension Regulator Assembly Replacement
Outline
Replacement
Removing the TG1 arm assembly
Removing the loading motor assembly
Removing the SE-521 board
Replacing the S tension regulator assembly
Reattaching the SE-521 board
Reattaching the loading motor assembly
Reattaching the TG1 arm assembly
Cleaning the tape guide
Adjustment after replacement
TENSION adjustment
Tape path adjustment
Notes
Use extreme care not to scratch the drum when replacing the S tension regulator
assembly.
Never loosen the screw shown in the figure. If the screw is loosened, replace the S
tension regulator with a new one.
Preparation
1.
2.
3.
4.

Set the unit to the unthreading end status.
Power off the unit.
Remove the top panel. (Refer to Section 3-3.)
Remove the cassette compartment. (Refer to Section 3-4.)

Tools
.
.
.
.
.

Torque driver’s bit (for M1.4) :
Torque driver (for 3 kgf.cm) :
Cleaning cloth :
Cleaning fluid :
Tweezers

7-34

J-6325-110-A
J-6325-400-A
3-184-527-01
9-919-573-01

DSR-2000/2000P

7-11. S Tension Regulator Assembly Replacement

Replacement
1. Removing the TG1 arm assembly
Remove the TG1 arm assembly.
(Refer to Section 7-13.)
2. Removing the loading motor assembly
Remove the loading motor assembly.
(Refer to Section 7-17.)
3. Removing the SE-521 board
(1) Disconnect the flexible card wire from the
connector (CN3) on the SE-521 board.
(2) Disconnect the flexible card wire from the
connector (CN4) on the SE-521 board.
(3) Remove the screw and remove the SE-521
board.
n
Use care about the claw of the worm holder.

4. Replacing the S tension regulator
assembly
(1) Remove the S tension regulator assembly by
removing the two screws.
(2) Turn the manual eject cover clockwise until
No.3 gear comes to the position shown in the
figure.
(3) Engage a gear on a new S tension regulator
assembly with No.3 gear as shown in the
figure, and align the notch of the S tension
regulator with the positioning pin on the
chassis, then attach the new assembly to the
chassis with the screw (a).
(4) Turn the manual eject cover counterclockwise to bring to the unthreading end position.
(5) Reattach the S tension regulator assembly to
the MD chassis with the screw (b).
Tightening Torque : 0.1 N.m {1 kgf.cm}
(6) Turn the manual eject cover clockwise to
enter the threading condition. At this operation, check the two points below.
The spring of the S tension regulator assembly shown in the figure do not contact the
post of No.3 gear.
The column pushes the spring under
unthreading end status.
Unless satisfy these conditions, perform the
step (2) and after.
(7) Turn the manual eject cover counterclockwise to bring to the unthreading end position.
DSR-2000/2000P

P1.4 x 3.5
SE-521 board

Connector
(CN4)

Connector
(CN3)
Claw of warm holder
Flexible card
wire
Flexible
card
wire

No.3 gear

(b) P1.4 x 3.5

Tension regulator
assembly

(a) P1.4 x 3.5

Notch
Manual eject
S tension regulator cover
assembly
Spring

Positioning pin

Post of No.3 gear

7-35

7-11. S Tension Regulator Assembly Replacement

5. Reattaching the SE-521 board
(1) Fit the hole and slotted hole on the SE-521
board on the two shafts on the MD chassis
respectively and fix it with the screw.
m
. At this operation, be careful not to pinch
the tip of the flexible card wire of the S
tension regulator assembly between the SE521 board and the chassis.
. Insert the SE-521 board under the claw of
the worm holder.

P1.4 x 3.5
SE-521 board

Slotted hole

Connector (CN4)

Connector (CN3)

Worm holder

Flexible card wire

(2) Reconnect the flexible card wire to the
connector (CN4) on the SE-521 board.
(3) Reconnect the flexible card wire of the S
tension regulator assembly to the connector
(CN3) on the SE-521 board.
6. Reattaching the loading motor
assembly
Reattach the loading motor assembly.
(Refer to Section 7-17.)
7. Reattaching the TG1 arm assembly
Reattach the TG1 arm assembly.
(Refer to Section 7-13.)

A
Flexible card wire

View from the A point
Worm holder claw

SE-521 board

8. Cleaning the tape guide
Wipe the tape guides of the S tension regulator
and the TG1 arm assemblies with a cleaning cloth
moistened with cleaning fluid.
Adjustment after replacement
9. TENSION adjustment
(Refer to Section 5-3-3.)
10. Tape path adjustment
(Refer to Section 8-2.)

7-36

DSR-2000/2000P

7-12. T Drawer Arm Assembly Replacement

7-12. T Drawer Arm Assembly Replacement
Outline
Replacement
Removing the T drawer arm assembly
Checking the mounting position of the T gear
Reattaching the T drawer arm assembly
Cleaning the tape guide
Adjustment after replacement
Checking the tape path adjustment
Note
Use extreme care no to scratch the drum when replacing the T drawer arm assembly.
Preparation
1.
2.
3.
4.

Let the unit into the unthreading position.
Power off the unit.
Remove the top panel. (Refer to Section 3-3.)
Remove the cassette compartment. (Refer to Section 3-4.)

Tools
. Cleaning cloth :
. Cleaning fluid :
. Tweezers

DSR-2000/2000P

3-184-527-01
9-919-573-01

7-37

7-12. T Drawer Arm Assembly Replacement

Replacement
1. Removing the T drawer arm assembly
(1) Remove the stop washer from the shaft on the
MD chassis and remove the T drawer arm
assembly.
(2) Remove the portion “a” of the T spring
shown in the figure from the notch in the
T drawer arm assembly with tweezers.
(3) Remove the T drawer arm assembly.

Stop washer

T drawer arm
assembly

Spring washer
T spring a
portion

Notch
T drawer arm
assembly

MD chassis

2. Checking the mounting position of the
T gear
Check that the engagement between the T gear
and No. 6 gear is in the position shown in the
figure.
3. Reattaching the T drawer arm
assembly
(1) Apply grease above 1/3 size of a tip of a
cotton swab, to the shaft on the MD chassis.
(2) Fit a new T drawer arm assembly on the shaft
and fit the hole in the T drawer arm assembly
on the protrusion on the T gear.
(3) Hook again the portion “a” of the T spring
unhooked in step 1- (2) on the notch in the
T drawer arm assembly with tweezers.
(4) Fit the spring washer on the shaft on the MD
chassis and fix it with the stop washer.
4. Cleaning the tape guide
Wipe the tape guide on the T drawer arm assembly with a cleaning cloth moistened with cleaning
fluid.

T spring

T gear

MD chassis

T drawer arm assembly
Tape guide
T drawer arm assembly
Stop washer
Spring washer
Notch
Sleeve

T spring
a portion

Hole
No.6 gear

T gear

Adjustment after cleaning
5. Checking the tape path adjustment
(Refer to Section 8-4.)

Shaft T spring Grease Slit T gear

7-38

MD chassis

DSR-2000/2000P

7-13. TG1 Arm Assembly Replacement

7-13. TG1 Arm Assembly Replacement
Outline
Replacement
Replacing the TG1 arm assembly
Cleaning the tape guide
Adjustment after replacement
TENSION adjustment
Checking the tape path adjustment
Note
Do avoid touching with bare hands to the tape cleaner a part of in TG1 arm assembly. Sharpness of the edge on the tape cleaner may cause a hand cut, therefore use
extreme care when replacing the TG1 arm assembly.
Preparation
1.
2.
3.
4.

Set the unit to the unthreading end status.
Power off the unit.
Remove the top panel. (Refer to Section 3-3.)
Remove the cassette compartment. (Refer to Section 3-4.)

Tools
.
.
.
.

Torque screwdriver’s bit (for M1.4) :
Torque screwdriver (for 3 kgf.cm) :
Cleaning cloth :
Cleaning fluid :

DSR-2000/2000P

J-6325-110-A
J-6325-400-A
3-184-527-01
9-919-573-01

7-39

7-13. TG1 Arm Assembly Replacement

Replacement
1. Replacing the TG1 arm assembly
(1) Remove the screw and remove the TG1 arm
assembly from the MD chassis.
(2) Fit two holes in a new TG1 arm assembly on
the two pins on the MD chassis respectively
and fix the assembly with the screw.
Tightening Torque : 0.1 N.m {1 kgf.cm}
2. Cleaning the tape guide
Wipe the tape guide on the TG1 arm assembly
and the tape cleaner with a cleaning cloth moistened with cleaning fluid.
n
The tape cleaner is not used for Serial No.
100911 - 101390 : UC
401551 - 401850 : CE
The set of above serial number, provided ARM
ASSY, TG1 (A-8279-399-C) for repair parts to
stabilize the tape path.
(Refer to Fig. 1 and Fig. 2)

Fig. 1

P1.4 x 3.5

Tape guide
TG1 arm assembly
(Part No. A-8279-399-B)
Pins

Serial No, 100911 - 101390 : UC
401551 - 401850 : CE

Fig. 2

P1.4 x 3.5

Adjustment after replacement
Tape guide

3. TENSION adjustment
(Refer to Section 5-3-3.)

Tape cleaner

TG1 arm assembly
(Part No. A-8279-399-C)
Pins

4. Checking the tape path adjustment
(Refer to Section 8-4.)

Serial No, 100001 - 100910, 101391 - : UC
400001 - 401550, 401851 - : CE

7-40

DSR-2000/2000P

7-14. TG8 Arm Assembly Replacement

7-14. TG8 Arm Assembly Replacement
Outline
Replacement
Replacing the TG8 arm assembly
Cleaning the tape guide
Adjustment after replacement
Checking the tape path adjustment
Preparation
1.
2.
3.
4.

Set the unit to the unthreading end status.
Power off the unit.
Remove the top panel. (Refer to Section 3-3.)
Remove the cassette compartment. (Refer to Section 3-4.)

Tools
.
.
.
.
.
.
.

Torque screwdriver’s bit (for M1.4) :
Torque screwdriver (for 3 kgf.cm) :
Washer extracting fixture (A) :
Washer mounting fixture Ø1.5 :
Cleaning cloth :
Cleaning fluid :
Tweezers

DSR-2000/2000P

J-6325-110-A
J-6325-400-A
J-6082-234-A
J-6082-231-A
3-184-527-01
9-919-573-01

7-41

7-14. TG8 Arm Assembly Replacement

Replacement
1. Replacing the TG8 arm assembly
(1) Insert a torque screwdriver through the
square hole of the pinch limiter assembly to
access the screw securing TG8 arm assembly.
Remove the screw to remove the TG8 arm
assembly.
(2) Fit a hole and a slotted hole in a new TG8
arm assembly on the two pins on the MD
chassis and fix it with the screw.
Tightening Torque : 0.1 N.m {1 kgf.cm}

TG8 arm assembly
Tape guide
P1.4 x 3.5

Suare hole of the
pinch limiter assembly
Pin

2. Cleaning the tape guide
Wipe the tape guide on the TG8 arm assembly
with a cleaning cloth moistened with cleaning
fluid.
Adjustment after replacement
3. Adjustment after replacement
Checking the tape path adjustment
(Refer to Section 8-4.)

7-42

DSR-2000/2000P

7-15. Rail Assembly Replacement

7-15. Rail Assembly Replacement
Outline
Replacement
Moving the S/T reel tables
Removing the S tension regulator assembly
Removing the T drawer arm assembly
Removing the RMP retainer (T1) assembly
Removing the head cleaner assembly
Removing the rail assembly
Reattaching the rail assembly
Reattaching the head cleaner assembly
Reattaching the RMP retainer (T1) assembly
Reattaching the T drawer arm assembly
Reattaching the S tension regulator assembly
Checking the threading/unthreading performance
Cleaning the tape guide
Adjustment after replacement
TENSION adjustment
Tape path adjustment
Note
Use extreme care not to scratch the drum and the tape guide when replacing the rail
assembly.
Preparation
1.
2.
3.
4.

Set the unit to the unthreading end status.
Power off the unit.
Remove the top panel. (Refer to Section 3-3.)
Remove the cassette compartment. (Refer to Section 3-4.)

Tools
.
.
.
.
.

Torque screwdriver’s bit (for M1.4) :
Torque screwdriver (for 3 kgf.cm) :
Cleaning cloth :
Cleaning fluid :
Tweezers

DSR-2000/2000P

J-6325-110-A
J-6325-400-A
3-184-527-01
9-919-573-01

7-43

7-15. Rail Assembly Replacement

Replacement
1. Moving the S/T reel tables
Bring the S/T reel tables to the L cassette position
(the most front side) by turning the reel shift
motor gear in the arrow direction by a finger.
[Reference]
This provides easy operation of succeeding tasks.

S reel table

2. Removing the S tension regulator
assembly
Remove the S tension regulator assembly.
(Refer to Section 7-11.)
3. Removing the T drawer arm assembly
Remove the T drawer arm assembly.
(Refer to Section 7-12.)

Reel shift
motor gear

T reel table

4. Removing the RMP retainer (T1)
assembly
Remove the two screws and remove the RMP
retainer (T1) assembly.
5. Removing the head cleaner
Remove the head cleaner. (Refer to Section 7-21.)
6. Removing the rail assembly
(1) Disconnect the flexible card wire from the
connector (CN2) on the SE-522 board.
n
Use extreme care not to fold and not to
scratch the flexible card wire when disconnecting.

SE-522 board
Connector (CN2)
Flexible card wire

7-44

DSR-2000/2000P

7-15. Rail Assembly Replacement

(2) Turn the manual eject cover clockwise and
align the two phase determining holes in the
mode gear assembly and in No.3 gear.
No.3 gear
Mode gear

Manual eject
cover

Phase determining hole

Phase
determining
hole

Phase determining hole

(3) Remove the three screws and remove the rail
assembly.
n
Use extreme care not to scratch the drum and
the tape guide when removing. Also great
care should be taken; not to fold and not to
scratch the flexible card wire of the LED
holder assembly when disconnecting.

P1.4 x 3.5

Rail assembly
Flexible card wire

DSR-2000/2000P

7-45

7-15. Rail Assembly Replacement

(4) Bring both shuttle (R) and shuttle (L) assemblies to the threading position shown in the
figure, by turning the gear on the back side of
the rail assembly by a finger

Shuttle (L) assembly

Rail assembly

Shuttle (R) assembly
Gear

(5) Unlock each two claws located on the left,
right and middle side of the LED holder
assembly with tweezers, and remove the LED
holder assembly from the rail assembly.
Claw

Claw
LED holder assembly

7-46

DSR-2000/2000P

7-15. Rail Assembly Replacement

7. Reattaching the rail assembly
(1) Reattach a new rail assembly to the LED
holder assembly.
(2) Ensure that the two phase determining holes
in the mode gear assembly and in No.3 gear,
which are already aligned in step 7- (2), are
respectively aligned with the two holes in the
MD chassis underneath each gear.
(3) Adjust the two phases determining holes in
No.6 and No.7 gears to align respectively
with the two holes in the MD chassis underneath each gear by turning No.7 gear by a
finger.

No.7 gear
No.6 gear

Phase determining
hole

Phase determining hole No.6 gear

(4) Turn the gear on the back side of the rail
assembly until the shuttle (R) and shuttle (L)
assemblies push the LED holder assembly as
far as it will go, and align the positioning
hole of the shuttle (L) assembly with the
positioning hole of the rail assembly.

No.7 gear Phase determining hole

Shuttle (R) assembly
Shuttle (L) assembly

Rail assembly
Gear

Positioning hole

Shuttle (L) asembly

Positioning hole

DSR-2000/2000P

Rail plate

7-47

7-15. Rail Assembly Replacement

(5) Keeping the state in step (4) and further more
holding the gear phase between S side and T
side, fit the hole and slotted hole in the rail
assembly on the two pins on the MD chassis
respectively.
(6) Fit the hole in the flexible card wire of LED
holder assembly on the pin on the MD
chassis.
(7) Fix the rail assembly with the three screws.
Tightening Torque : 0.1 N.m {1 kgf.cm}
(8) Reconnect the flexible card wire to the
connector (CN2) on the SE-522 board.

P1.4 x 3.5

Hole

Slotted hole
Rail assembly
Pin

Flexible card wire

8. Reattaching the head cleaner
Reattach the head cleaner. (Refer to Section 7-21.)

9. Reattaching the RMP retainer (T1)
assembly
Fit the hole and slotted hole in the RMP retainer
(T1) assembly on the pins on the MD chassis
respectively, then fix it with the two screws.
10. Reattaching the T drawer arm
assembly
Reattach the T drawer arm assembly.
(Refer to Section 7-12.)

11. Reattaching the S tension regulator
assembly
Reattach the S tension regulator assembly.
(Refer to Section 7-11.)
12. Checking the threading/unthreading
performance
Check the threading/unthreading is performed
smoothly by turning the manual eject cover.
13. Cleaning the tape guide
Wipe the tape guides placed in followings with a
cleaning cloth moistened with cleaning fluid.
. T drawer arm assembly
. S tension regulator assembly
. Shuttle (R) assembly
. Shuttle (L) assembly
Adjustment after replacement
14. TENSION adjustment
(Refer to Section 5-3-3.)
15. Tape path adjustment
(Refer to Section 8-2.)
7-48

DSR-2000/2000P

7-16. Capstan Motor Replacement

7-16. Capstan Motor Replacement
Outline
Replacement
Removing the MD cover
Replacing the capstan motor
Reattaching the MD cover
Cleaning the capstan shaft
Adjustment after replacement
CAPSTAN ONLY adjustment
Checking the tape path adjustment
Preparation
1.
2.
3.
4.
5.
6.

Set the unit in to the unthreading end status.
Power off the unit.
Remove the top panel. (Refer to Section 3-3.)
Remove the bottom panel. (Refer to Section 3-3.)
Remove the right side panel. (Refer to Section 3-3.)
Remove the cassette compartment. (Refer to Section 3-4.)

Tools
.
.
.
.

Torque screwdriver’s bit (for M1.4) :
Torque screwdriver (for 3 kgf.cm) :
Cleaning cloth :
Cleaning fluid :

DSR-2000/2000P

J-6325-110-A
J-6325-400-A
3-184-527-01
9-919-573-01

7-49

7-16. Capstan Motor Replacement

Replacement
1. Removing the MD cover.
Remove the MD cover. (Refer to Section 7-2.)

Flexible card wire
CN1

2. Replacing the capstan motor
(1) Disconnect the flexible card wire from the
connector (CN1) on the MS-64 board.
(2) While supporting the capstan motor by hand
from the back side of the MD chassis, remove
the two screws in the upper side of the
chassis to remove the capstan motor.
(3) Wipe the mounting surfaces of a new capstan
motor and the MD chassis with a cleaning
cloth moistened with cleaning fluid.
(4) Insert the new capstan motor into the hole in
the MD chassis positioning as shown in the
figure and fix it with the two screws.
Tightening torque : 0.1 N.m {1 kgf.cm}
n
Use care not to scratch the capstan motor
pivot when inserting the capstan motor.

MS-64 board

(5) Reconnect the flexible card wire of the
capstan motor on the back side of the unit to
the connector (CN1) on the MS-64 board.

Cleaning

3. Reattaching the MD cover
Reattach the MD cover. (Refer to Section 7-2.)
Capstan motor

4. Cleaning the Capstan shaft
Wipe the capstan shaft with a cleaning cloth
moistened with cleaning fluid.
Adjustment after replacement

P 1.4 x 3.5

5. CAPSTAN ONLY adjustment
(Refer to Section 5-3-3.)
6. Checking the tape path adjustment
(Refer to Section 8-4.)

7-50

DSR-2000/2000P

7-17. Loading Motor Replacement

7-17. Loading Motor Replacement
Outline
Replacement
Disconnecting the connector
Replacing the loading motor assembly
Reconnecting the connector
Preparation
1.
2.
3.
4.

Set the unit to the unthreading end status.
Power off the unit.
Remove the top panel. (Refer to Section 3-3.)
Remove the cassette compartment. (Refer to Section 3-4.)

Tools
. Torque screwdriver’s bit (for M1.4) :
. Torque screwdriver (for 3 kgf.cm) :
. Tweezers

J-6325-110-A
J-6325-400-A

Replacement
1. Disconnecting the connector
Disconnect the harness from the connector
(CN19) on the MS-64 board with tweezers.
2. Replacing the loading motor assembly
(1) Remove the two screws to remove the
loading motor assembly.
(2) Align a positioning hole in a new loading
motor with the positioning pin on the MD
chassis and engage the motor gear with the
FG gear.
(3) Fix the loading motor assembly with the two
screws.
Tightening Torque : 0.1 N.m {1 kgf.cm}

Harness

P1.4 x 3.5
P1.4 x 3.5
CN19
MS-64 board
Loading motor
assembly

3. Reconnecting the connector
Reconnect the harness to the connector (CN19)
on the MS-64 board with tweezers.

Motor gear

FG gear assembly

DSR-2000/2000P

7-51

7-18. Reel Shift Motor Assembly Replacement

7-18. Reel Shift Motor Assembly Replacement
Outline
Replacement
Removing the pinch limiter assembly
Removing the pinch solenoid assembly
Replacing the reel shift motor assembly
Reattaching the pinch solenoid assembly
Reattaching the pinch limiter assembly
Note
Prepare a new stop washer when replacing the reel shift motor assembly.
Stop washer (1.5) : 3-669-465-01 x 1 (for mounting the pinch limiter assembly)
Preparation
1.
2.
3.
4.

Set the unit to the unthreading end status.
Power off the unit.
Remove the top panel. (Refer to Section 3-3)
Remove the cassette compartment. (Refer to Section 3-4)

Tools
.
.
.
.
.
.
.

Torque screwdriver’s bit (for M1.4) :
Torque screwdriver (for 3 kgf.cm) :
Washer extracting fixture (A) :
Washer mounting fixture Ø1.5 :
Cleaning cloth :
Cleaning fluid :
Tweezers

7-52

J-6325-110-A
J-6325-400-A
J-6082-234-A
J-6082-231-A
3-184-527-01
9-919-573-01

DSR-2000/2000P

7-18. Reel Shift Motor Assembly Replacement

Replacement
1. Removing the pinch limiter assembly
Remove the pinch limiter assembly.
(Refer to Section 7-5.)

P1.4 x 3.5
Reel shift mortor assembly

2. Removing the pinch solenoid
assembly
Remove the pinch solenoid assembly.
(Refer to Section 7-7.)
3. Replacing the reel shift motor
assembly
(1) Disconnect the harness of the reel shift motor
assembly from the connector (CN5) on the
MS-64 board with tweezers.
(2) Remove the screw to remove the reel shift
motor assembly.
(3) Fit two holes in a new reel shift motor
assembly shown in the figure on the two pins
on the MD chassis and engage it with the
gear A.
(4) Reattach the reel shift motor assembly with
the screw.
Tightening Torque : 0.1 N.m {1 kgf.cm}
(5) Reconnect the harness of the reel shift motor
to the connector (CN5) on the MS-64 board.

Positioning hole

Gear
Pin

CN5
MS-64 board

4. Reattaching the pinch solenoid
assembly
Reattach the pinch solenoid assembly.
(Refer to Section 7-7.)
5. Reattaching the pinch limiter
assembly
Reattach the pinch limiter assembly.
(Refer to Section 7-5.)

DSR-2000/2000P

7-53

7-19. MIC Assembly Replacement

7-19. MIC Assembly Replacement
Outline
Replacement
Removing the MD cover
Disconnecting the flexible card wire
Moving the S/T reel tables
Removing the L push plate
Removing the MIC spring
Replacing the MIC assembly
Moving the S/T reel tables
Reattaching the MIC spring
Reattaching the L push plate
Reconnecting the flexible card wire
Reattaching the MD cover
Note
Prepare a new stop washer when replacing the MIC holder.
Stop washer (1.2) : 3-559-408-11
Do avoid touching the terminal on the MIC holder and wiping it with cleaning fluid.
When need cleaning, wipe it carefully with a soft dry cloth.
Use care not to lose a poly-slider washer between the base plate and the MIC
assembly.
Preparation
1.
2.
3.
4.
5.
6.

Set the unit to the unthreading end status.
Power off the unit.
Remove the top panel. (Refer to Section 3-3.)
Remove the bottm panel. (Refer to Section 3-3.)
Remove the right side panel. (Refer to Section 3-3.)
Remove the cassette compartment. (Refer to Section 3-4.)

Tools
.
.
.
.
.

Torque screwdriver’s bit (for M1.4) :
Torque screwdriver (for 3 kgf.cm) :
Washer extracting fixture (A) :
Washer mounting fixture Ø1.5 :
Tweezers

7-54

J-6325-110-A
J-6325-400-A
J-6082-234-A
J-6082-231-A

DSR-2000/2000P

7-19. MIC Assembly Replacement

Replacement
1. Removing the MD cover
Remove the MD cover. (Refer to Section 7-2.)

MIC assembly
flexible card wire

2. Disconnecting the flexible card wire
Disconnect the flexible card wire from the
connector (CN7) on the MS-64 board located on
the back side of the MD chassis.

Connector (CN7)

MS-64 board

3. Moving the S/T reel tables
Turn the reel shift motor gear in the arrow
direction by a finger and bring the S/T reel tables
to the standard cassette position (the most front
side).

S reel table

4. Removing the L push plate
Remove the L push plate. (Refer to Section 7-3.)
Reel shift
motor gear

T reel table

5. Removing the MIC spring
Unhook the hooks on the both ends of the MIC
spring which hold the MIC arm and the RLR
assemblies.

RLR assembly

MIC spring
MIC assembly
DSR-2000/2000P

7-55

7-19. MIC Assembly Replacement

6. Replacing the MIC assembly
(1) Remove the stop washer and the two screws
which secure the MIC assembly to the MD
chassis, and remove the MIC assembly.
(2) Insert a tip of the flexible card wire of a new
MIC assembly between the chassis and the
front MD chassis to bring it to the back side
of the unit.
n
Use great care not to fold and scratch the
flexible card wire during this operation.
(3) Fit the boss of the MIC arm on the shaft of
the MD chassis and also fit the recess on the
reel plate shaft.
Fit the two guide holes in the MIC assembly
on the pins on the MD chassis, and fix the
assembly with the two screws and a new stop
washer.
Tightening Torque : 0.1 N.m {1 kgf.cm}

P1.4 x 3.5
MIC assembly
Guide hole
Stop washer

P1.4 x 3.5

Boss of MIC arm
Recess
Flexible card wire
Guide hole

Pin
Reel plate shaft
Pin

7-56

DSR-2000/2000P

7-19. MIC Assembly Replacement

7. Moving the S/T reel tables
Turn the reel shift motor gear in the arrow
direction by a finger and bring the S/T reel tables
to the S-cassette position (the drum side).
Confirm that the S/T reel tables and the MIC
assembly shift smoothly.

S reel table

Reel shift
motor gear

T reel table

8. Reattaching the MIC spring
Reattach the MIC spring removed in step 5 to the
MIC arm and RLR assemblies.
9. Reattaching the L push plate
Reattach the L push plate. (Refer to Section 7-3.)
10. Reconnecting the flexible card wire
Reconnect the flexible card wire to the connector
(CN7) on the MS-64 board located on the back
side of the MD chassis.
RLR assembly

11. Reattaching the MD cover.
Reattach the MD cover. (Refer to Section 7-2.)

MIC spring
MIC assembly

DSR-2000/2000P

7-57

7-20. MIC Holder Assembly Replacement

7-20. MIC Holder Assembly Replacement
Outline
Replacement
Removing the MD cover
Removing the MIC assembly
Replacing the MIC holder assembly
Reattaching the MIC assembly
Reattaching the MD cover
Note
Prepare new stop washers when replacing the MIC holder.
Stop washer (1.2) : 3-559-408-11 x 2 (for mounting the MIC holder assembly)
Stop washer (1.5) : 3-669-465-01 x 1 (for mounting the MIC assembly)
Do avoid touching the terminal on the MIC holder and wiping it with cleaning fluid.
When need cleaning, wipe it carefully with a soft dry cloth.
Use care not to lose a poly-slider washer between the base plate and the MIC
assembly.
Preparation
1.
2.
3.
4.
5.
6.

Tools
.
.
.
.
.
.

Torque screwdriver’s bit (for M1.4) :
Torque screwdriver (for 3 kgf.cm) :
Washer extracting fixture (A) :
Washer mounting fixture Ø1.5 :
Washer mounting fixture Ø1.2 :
Tweezers

7-58

J-6325-110-A
J-6325-400-A
J-6082-234-A
J-6082-231-A
J-6082-232-A

DSR-2000/2000P

7-20. MIC Holder Assembly Replacement

Replacement
1. Removing the MD cover
Remove the MD cover. (Refer to Section 7-2.)

Flexible card wire
MIC holder assembly

2. Removing the MIC assembly
Remove the MIC assembly.
(Refer to Section 7-19.)
3. Replacing the MIC holder
subassembly
(1) Remove the portion A shown of the flexible
card wire from the MIC arm assembly as
shown in the figure.
(2) Remove the two stop washers from the back
side of the MIC assembly and remove the
MIC holder assembly.
(3) Fix a new MIC holder assembly to the MIC
assembly with two new stop washers (1.2).
n
Use great care not to fold and not to scratch
the flexible card wire when reattaching.

Stop washer

MIC arm assembly

(4) Fix the flexible card wire to the MIC arm
assembly as shown in the figure.
(5) Insert a tip of the flexible card wire of the
MIC assembly between the chassis and the
front MD chassis to bring it to the back side
of the unit.
n
Use extreme care not to fold and not to
scratch the flexible card wire at this operation.

Stop washer

Flexible card wire

4. Reattaching the MIC assembly
Reattach the MIC assembly.
(Refer to Section 7-19.)
MIC arm assembly

5. Reattaching the MD cover
Reattach the MD cover. (Refer to Section 7-2.)

DSR-2000/2000P

7-59

7-21. HC Roller Assembly Replacement

7-21. HC Roller Assembly Replacement
Outline
Replacement
Disconnecting the connector
Removing the head cleaner assembly
Replacing the HC roller assembly
Reattaching the head cleaner assembly
Reconnecting the connector
Note
Prepare a new stop washer when replacing the HC roller assembly.
Stop washer (0.8) : 3-315-414-31 x 1
Bare-handed touch to the HC roller assembly is prohibited. Do put on cloth gloves
before replacing.
Preparation
1. Set the unit to the unthreading end status.
2. Power off the unit.
3. Remove the top panel. (Refer to Section 3-3.)
Tools
.
.
.
.

Torque screwdriver’s bit (for M1.4) :
Torque screwdriver (for 3 kgf.cm) :
Washer extracting fixture (A) :
Washer mounting fixture Ø1.8 :

7-60

J-6325-110-A
J-6325-400-A
J-6082-234-A
J-6082-233-A

DSR-2000/2000P

7-21. HC Roller Assembly Replacement

Replacement
1. Disconnecting the connector
Disconnect the harness from the connector
(CN12) on the MS-64 board with tweezers.

P1.4 x 3.5
Head cleaner assembly

2. Removing the head cleaner assembly
Remove the two screws and pull off the head
cleaner assembly in the arrow direction.

P1.4 x 3.5

CN12

3. Replacing the HC roller assembly
(1) Remove the stop washer to remove the HC
roller assembly.
(2) Attach a new HC roller assembly with a new
stop washer.
n
Avoid bare-handed touch to the HC roller
assembly.
In addition, do not give an excessive force to
it at removal and reattachment, it may cause
deformation.
Operation supporting the back side of the HC
roller assembly by fingers is required.

DSR-2000/2000P

Stop washer
HC roller assembly

HC roller arm assembly

7-61

7-21. HC Roller Assembly Replacement

4. Reattaching the head cleaner
assembly
Align the two positioning holes in the head
cleaner assembly with the two positioning pins on
the MD chassis and fix the assembly with the two
screws.
Tightening torque : 0.1 N.m {1 kgf.cm}

P1.4 x 3.5
Iron core
Head cleaner assembly

Positioning hole

P1.4 x 3.5

Positioning pin
Positioning hole
CN12

Positioning pin

5. Checking the performance of the head
cleaner assembly
Check that the HC roller assembly contacts the
drum assembly in parallel when the solenoid’s
iron core of the head cleaner assembly is in the
pull-in state by being pressed in the arrow
direction.
6. Reconnecting the connector
Reconnect the harness to the connector (CN12)
on the MS-64 board.

7-62

Upper and lowerspaces
Only upperspace : NG
Only lowerspace : NG
are same : OK

Drum

Roller

DSR-2000/2000P

7-22. Head Cleaner Solenoid Replacement

7-22. Head Cleaner Solenoid Replacement
Outline
Replacement
Removing the head cleaner assembly
Replacing the head cleaner solenoid
Reattaching the head cleaner assembly
Checking the performance of the head cleaner assembly
Preparation
1. Set the unit to the unthreading end status.
2. Power off the unit.
3. Remove the top panel. (Refer to Section 3-3.)
Tools
. Torque screwdriver’s bit (for M1.4) :
. Torque screwdriver (for 3 kgf.cm) :

DSR-2000/2000P

J-6325-110-A
J-6325-400-A

7-63

7-22. Head Cleaner Solenoid Replacement

Replacement
1. Removing the head cleaner assembly
Remove the head cleaner assembly.
(Refer to Section 7-21.)
2. Replacing the head cleaner solenoid
(1) Remove the two screws on the back side of
the head cleaner assembly.
(2) Remove the solenoid with the spring on it.
(3) Remove the compression coil spring from the
solenoid.
(4) Fit the compression coil spring on a new
solenoid’s iron core.
(5) Pull out the iron core until a recess comes in
sight, then fix the solenoid to the head cleaner
assembly.
(6) Align the two holes in the solenoid with the
two slotted holes in the HC base assembly
and fix temporally with the two screws.
n
Tighten the screws just enough to move the
head cleaner solenoid.
(7) Adjust the solenoid position to meet the
specification of the clearance between the HC
roller arm assembly and the tip of the HC
slider under the condition that the iron core
comes to the pull-in state by being pressed in
the arrow direction, then tighten the two
screws.
Tightening torque : 0.2 N.m {2 kgf.cm}

Solenoid
Recess
Iron core
Compression
coil spring
Head cleaner base
assembly

Slotted hole

PSW2.6 x 4
Head cleaner assembly

HC slider
Iron core

Solenoid

HC slider

3. Reattaching the head cleaner
assembly
Reattach the head cleaner assembly.
(Refer to Section 7-21.)

Specification:1.5 to 1.8 mm

4. Checking the performance of the head
cleaner assembly
Check the performance of the head cleaner
assembly. (Refer to Section 7-21.)

7-64

DSR-2000/2000P

7-23. Cassette Compartment Motor Replacement

7-23. Cassette Compartment Motor Replacement
Outline
Replacement
Removing the motor gear assembly
Replacing the motor assembly
Reattaching the motor gear assembly
Preparation
1.
2.
3.
4.

Set the unit to the unthreading end status.
Power off the unit.
Remove the top panel. (Refer to Section 3-3.)
Remove the cassette compartment. (Refer to Section 3-4.)

Tools
.
.
.
.

Torque screwdriver (for 3 kgf.cm) :
Torque screwdriver’s bit (for M2) :
Grease (SGL-941) :
Tweezers

J-6325-400-A
J-6325-380-A
7-662-001-39

Replacement
1. Removing the motor gear assembly
(1) Remove the harness of the motor gear from
the connector (CN3) on the CC-83 board in
the cassette compartment.
(2) Remove the motor gear assembly from the
cassette compartment by removing the two
screws.

Motor gear assembly

Screw M2
Screw M2

Harness
CC-83 board

DSR-2000/2000P

CN3

7-65

7-23. Cassette Compartment Motor Replacement

2. Replacing the motor assembly
(1) Release the upper and lower claws of the
pivot bracket to remove the pivot bracket.
n
Be careful not to lose the worm gear, which
also comes off at this operation.

Motor assembly

Worm gear

(2) Remove the gear B from the shaft of the
motor bracket assembly.
(3) Remove the two screws to remove the motor
assembly from the motor bracket.
(4) Fix a new motor assembly to the motor
bracket positioning as shown in the figure
with the two screws.
n
Be reminded a new motor assembly has the
gear A on its shaft.
Tightening torque : 0.2 N.m {2 kgf.cm}

Motor bracket

Pivot bracket
Gear A
Screw M2
Claw
Pivot bracket

(5) Reattach the gear B to the shaft of the motor
bracket assembly.
(6) Make a coupling between the worm gear and
the gear B and insert the pivot bracket shaft
from another side of the worm gear.
(7) Fix the upper and lower claws to the motor
bracket.
3. Reattaching the motor gear assembly
(1) Bend the two terminals in the motor gear
assembly to meet the specification of their
bent angle shown in the figure.
(2) With the worm gear in the motor gear
assembly engaged with the worm wheel,
insert the two protrusions of the motor gear
assembly into the holes in the cassette
compartment and fix with two screws.
(3) Align the hole in the drive gear (L) assembly
with the hole in the cassette compartment by
turning the gear B of the motor gear assembly
by a finger.
(4) Apply a grain of grease on the worm gear in
the motor gear assembly.
(5) Reconnect the harness of the motor gear
assembly to the connector (CN3) on the
CC-83.

Gear B

Claw

Motor gear assembly Screw M2
Screw M2
Gear B
Grease
Worm gear
Positioning hole
Driving gear (L)
assembly

Protrusions

CN3
Specification
45d ±10d

7-66

DSR-2000/2000P

7-24. Switching Regulator Replacement

7-24. Switching Regulator Replacement
Outline
Replacement
Disconnecting the connectors
Replacing the switching regulator
Reconnecting the connectors
Preparation
1. Power off the unit.
2. Remove the top panel. (Refer to Section 3-3.)
Replacement
1. Disconnecting the connectors
Disconnect the three connectors, the two connectors (4P and 10P) on the upper side of the switching regulator, and one connector (7P) on the side.
2. Replacing the switching regulator
(1) Remove the two screws.
(2) Pull out the switching regulator in the arrow
direction.
(3) Set a new switching regulator at the base of
the unit and slide it along the chassis M in the
reverse direction of the arrow as far as it
pushes the rear chassis.
(4) Tighten the two screws (a and b) to fix the
switching regulator.

Switching regulator

a BVTT3 x 6
(S tight)

Connector (7P)

b BVTT3 x 6 (S tight)
Rear chassis

M chassis

3. Reconnecting the connectors
Reconnect the three connectors removed in step 1.

Connector (4P)

Connector (10P)

DSR-2000/2000P

7-67

Section 8
Tape Path Alignment
Tape path adjustment is very important adjustment to run tape under the optimum
conditions for tape.
If this adjustment is not performed correctly, tape may be damaged.
Perform this adjustment with utmost attention.
Perform this adjustment after the cassette compartment assembly is removed from
VTR.

8-1. General Information for Tape Path Adjustment
Tools
1. Alignment tape
The following alignment tapes are necessary for tape path adjustment.
. XH2-1AST (Standard cassette) :
8-967-999-02
. XH5-1A2 (Mini cassette) :
8-967-999-22 (NTSC)
. XH5-1AP2 (Mini cassette) :
8-967-999-26 (PAL)
2. Tape guide adjustment driver
The following tape guide adjustment driver which is available as the Sony service
tool is necessary for height adjustment of tape guide.
. Tape guide adjustment driver :
J-6082-362-A

Tape guide
adjustment driver

3. Tape path adjustment board
Use the tape path adjustment board (DJ-461) to parforme the tape path adjustment.
. Tape path adjustment board, DJ-461 : J-6444-610-B
4. The required tools in addition to the above listed tools.
. Oscilloscope (Tektronix 2445B or equivalent)
. Small mirror for adjustment :
J-6080-029-A
. Cleaning cloth :
3-184-527-01
. Cleaning fluid :
9-919-573-01

Tape guide

TG1 arm assembly

Preparation of Tape Path Adjustment
1. Cassette compartment assembly
It is not necessary to remove the cassette compartment assembly during tape path
adjustment.
2. Cleaning the tape running surface
Clean the tape running surface of tape guides, head drum and video heads using the
cleaning cloth moistened with cleaning fluid.
. Cleaning cloth :
3-184-527-01
. Cleaning fluid :
9-919-573-01

DSR-2000/2000P

8-1

8-1. General Information for Tape Path Adjustment

3. Information to use the tracking alignment tape (XH2-1AST)
Check the following items before entering the tracking adjustment mode.
. How to enter the maintenance menu, refer to Section 5-2-2.
. How to exit the maintenance menu, refer to Section 5-2-3.
4. Operating procedures of tracking adjustment
(1) Enter the maintenance menu.
(2) Move the cursor to “TAPE PATH ADJUST” which is
displayed with a white background using the
[AUDIO|IN] (9) or [IN] (0) key.
CH-4

(9)

OUT

AUDIO
DELETE

EDIT

REVIEW

ENTRY SHIFT

OUT

(0)

(3) Press the [ENTRY|SHIFT] (8) key.
This selects “TAPE PATH ADJUST” and menu of the
lower level directory appears.
CH-4

OUT
AUDIO

DELETE

EDIT

REVIEW

ENTRY SHIFT

(8)

OUT

(4) Move the cursor to “TRACKING ADJUST” which is
displayed with a white background using the
[AUDIO|IN] (9), or [IN] (0) key.
CH-4

(9)

OUT

AUDIO
DELETE

EDIT

REVIEW

ENTRY SHIFT

OUT

(0)

8-2

DSR-2000/2000P

8-1. General Information for Tape Path Adjustment

(5) Press the [ENTRY|SHIFT] (8) key to show the
“START OK?” display.
IN

CH-4

OUT
AUDIO

DELETE

EDIT

REVIEW

ENTRY SHIFT

(8)

OUT

(6) Press the [SET] key.
PB

PREROLL

REC

SET

HOLD COUNTER SEL

EDIT

(7) Display the “TRACKING ADJUST” on the screen.
The adjustments that are described in sections 8-2, 8-4
to 8-8 are performed under this mode.
n
This unit does not have the tracking shift function.
Instead of having the tracking shift function, the
tracking alignment tape XH2-1AST has already been
recorded in the factory so that the servo is locked at 50
% off-track automatically.

DSR-2000/2000P

8-3

8-1. General Information for Tape Path Adjustment

5. Tape guide locations
S3 (Tension regulator)

Head drum

Capstan

Pinch roller

S reel

Standard cassette

M cassette

Mini cassette

T reel

6. Tape running condition
FWD

(
S4

Tension
regulator
S3

Capstan shaft

)
S2

Head drum

S reel

T4
T reel

The hatched areas (marked by /////) are contacting with tape or pressing tape.
8-4

DSR-2000/2000P

8-1. General Information for Tape Path Adjustment

7. Preparation of signal measurement
Use the tape path adjustment board DJ-461 (J-6444-610-B)
to perform the tape path adjustment.
(1) Setting of the tape path adjustment board
Connect the connector CN1 on the tape path adjustment board with the connector CN303 on the EX-752
board of the unit.
Connect the connector CN2 on the tape path adjustment board with the connector CN113 on the SY-278
board using the harness supplied with the board.

(3) Measuring points/signal for adjustment
Signal name

Board

RF output
DJ-461
(signal after envelope detection)

TP2

Switching pulse output

DJ-461

TP3

DJ-461

GND

Tape path adjustment
board, DJ-461

Harness (supplied with the board)
Tape path adjustment
CN2 board, DJ-461

SY-278 board
(CN113)

Measuring point

CN1

E1
TP1
TP2
TP3
E2

[Preference]

EX-752 board (CN303)

F 012

789A

3456

BCDE

(2) Switch setting of the tape path adjustment board

SWITCHING

OFF

[0]

OFF

[1]

OFF

[0]

OFF

[1]

WJPB E1

OFF

[2]

WJPB E2

OFF

[3]

WJPB O1

OFF

[2]

WJPB O2

OFF

[3]

NJPB E1

OFF

[2]

[5]

REC E

OFF

REC O
PRE E
PRE O

HEAD

Bit

Setting

Function

NJPB E2

[3]

Select the REC head.

NJPB O1

OFF

[2]

NJPB O2

[3]

OFF

DSR-2000/2000P

Activate the switch setting of DJ-461

8-5

8-2. Tape Path Adjustment

8-2. Tape Path Adjustment
Basic knowledge

To perform the tracking adjustment using the alignment tape (XH2-1AST), refer
the following items.
. For the procedure to enter the maintenance menu, refer to Section 5-2-2.
. For the procedure to exit the maintenance menu, refer to Section 5-2-3.
. For the operating procedure of the maintenance menu during the tracking adjustment, refer to Section 8-1.
Tools
. Alignment tape, XH2-1AST :
. Tape path adjustment board, DJ-461 :
. Dual trace oscilloscope

8-967-999-02
J-6444-610-B

max.
4/5 Div
3 Div

min.

Specification : max. _ min. < 4/5 Div

5. Adjust the RF waveform until it satisfies the specification by changing the height of the S2 and T2 guides.
. When the RF waveform at the entrance side forms
the shape of the solid line shown in Fig.1, turn the
guide S2 clockwise to obtain the flat waveform.
n
This adjustment must end with the clockwise
rotation of the guide S2

2
Guide S2
Entrance side

Exit side
max.

4/5 Div
min.

3 Div

Specification : max. _ min. < 4/5 Div
Fig.1

8-6

DSR-2000/2000P

8-2. Tape Path Adjustment

. When the RF waveform at the entrance side forms
the shape of the solid line shown in Fig.2, turn the
guide S2 counterclockwise to waveform as shown by
the solid line in Fig.1. Then turn the guide S2
clockwise to obtain the desired waveform.
n
This adjustment must end with the clockwise rotation
of the guide S2.

3
Guide S2
Entrance side

Exit side
max.

4/5 Div
min.

3 Div

Specification : max. _ min. < 4/5 Div
Fig.2

. When the RF waveform at the exit side forms the
shape of the solid line shown in Fig.3, turn the guide
T2 clockwise to obtain the flat waveform.
n
This adjustment must end with the clockwise rotation
of the guide S2.

2
Guide T2
Exit side

Entrance
side
max.
4/5 Div
min.

3 Div

Specification : max. _ min. < 4/5 Div
Fig.3

DSR-2000/2000P

8-7

8-2. Tape Path Adjustment

. When the RF waveform at the exit side forms the
shape of the solid line shown in Fig.4, turn the guide
T2 counterclockwise to waveform as shown by the
solid line in Fig.3. Then turn the guide T2 clockwise
to obtain the desired waveform.
n
This adjustment must end with the clockwise rotation
of the guide T2.

3
Guide T2
Exit side

Entrance
side
max.
4/5 Div
min.

3 Div

Specification : max. _ min. < 4/5 Div
Fig.4

6. Measure the minimum amplitude of the RF waveform,
and confirm that the amplitude difference between the
maximum and the minimum of the RF waveform
satisfies the specification.

max.
4/5 Div
3 Div

min.

Specification : max. _ min. < 4/5 Div

8-8

DSR-2000/2000P

8-3. RF Switching Position Adjustment

8-3. RF Switching Position Adjustment
Be sure to perform the RF switching position adjustment whenever the tape path
adjustment (refer to Section 8-2) is performed.
Perform this adjustment in the AUTO mode.
Basic knowledge

To perform the RF switching position adjustment using the alignment tape (XH51A2 for NTSC or XH5-1AP2 for PAL), refer the following items.
. For the procedure to enter the maintenance menu, refer to Section 5-2-2.
. For the procedure to exit the maintenance menu, refer to Section 5-2-3.
Tools
Alignment tape, XH5-1A2 :
XH5-1AP2 :

8-967-999-22 (for NTSC)
8-967-999-26 (for PAL)

Adjustment procedure
RF switching position adjustment using the
[AUTO adjustment]
1. Enter the maintenance menu.
2. Move the cursor to “TAPE PATH ADJUST” which is
displayed with a white background using the
[AUDIO|IN] (9) or [IN] (0) key.
CH-4

(9)

OUT

AUDIO
DELETE

EDIT

REVIEW

ENTRY SHIFT

OUT

(0)

3. Press the [ENTER|SHIFT] (8) key.
“TAPE PATH ADJUST” is selected and its lower
layer submenu appears.
CH-4

OUT
AUDIO

DELETE

EDIT

DSR-2000/2000P

REVIEW

ENTRY SHIFT

(8)

OUT

8-9

8-3. RF Switching Position Adjustment

4. Move the cursor to “RF SWITCHING POSITION”
which is displayed with a white background using the
[AUDIO|IN] (9) or [IN] (0) key.
CH-4

(9)

OUT

AUDIO
DELETE

EDIT

ENTRY SHIFT

REVIEW

OUT

(0)

5. Select “START OK?” by pressing the
[ENTRY|SHIFT] (8) key.
CH-4

OUT
AUDIO

DELETE

EDIT

ENTRY SHIFT

REVIEW

(8)

OUT

6. Press the [SET] key.
PB

PREROLL

REC

SET

HOLD COUNTER SEL

2
EDIT

7. Playback the alignment tape XH5-1A2 for NTSC or
XH5-1AP2 for PAL. (display 2)
Then the unit starts the RF switching position automatic adjustment. (display 3)
3

8-10

DSR-2000/2000P

8-3. RF Switching Position Adjustment

8. When the adjustment is completed, the display 5
“COMPLETE” appears and alignment tape is automatically ejected.
n
When the “ADJUST INCOMPLETE” appears on the
monitor screen, check that the alignment tape which is
played back is XH5-1A2 for NTSC, or XH5-1AP2 for
PAL.

9. Press the [MENU] key to return to the maintenance
menu.

DSR-2000/2000P

8-11

8-4. Tape Path Adjustment Confirmation

8-4. Tape Path Adjustment Confirmation
Be sure to perform tracking adjustment described in Section 8-3 after performing
the tracking adjustment in Section 8-2.
Basic knowledge

To perform tracking adjustment using the alignment tape (XH2-1AST), refer to
the following items.
. For the procedure to enter the maintenance menu, refer to Section 5-2-2.
. For the procedure to exit the maintenance menu, refer to Section 5-2-3.
. For the operating procedure of the maintenance menu during the tracking adjustment, refer to Section 8-1.
Tools
. Alignment tape, XH2-1AST :
. Tape path adjustment board, DJ-461 :
. Dual trace oscilloscope

8-967-999-02
J-6444-610-B

Check procedure
1. Connect the oscilloscope as follows :
CH-1 : TP2 / DJ-461
CH-2 : TP3 / DJ-461
TRIG : CH-2
2. Insert the alignment tape XH2-1AST on the VTR.
3. Put the unit into PLAY mode.
4. Adjust the variable VOLTS/DIV control of the
oscilloscope so that the maximum amplitude of the RF
waveform becomes the three DIVISIONs on the
oscilloscope.
5. Measure the minimum amplitude of the RF waveform,
and confirm that the amplitude difference between the
maximum and the minimum of the RF waveform
satisfies the specification.
6. Confirm that fluctuation of the RF waveform satisfies
the specification.

max.
4/5 Div
3 Div

min.

Specification : max. _ min. < 4/5 Div

Fluctuations
4/5 Div
or less
3 Div

Specification : Fluctuation (
) with in
4/5 divisions or less.

8-12

DSR-2000/2000P

8-5. Search Forward (x5) Waveform Check

x5) Waveform Check
8-5. Search Forward (x
Basic knowledge

8-967-999-02
J-6444-610-B

Check procedure
1. Connect the oscilloscope as follows :
CH-1 : TP2 / DJ-461
CH-2 : TP3 / DJ-461
TRIG : CH-2
2. Insert the alignment tape XH2-1AST on the VTR.
3. Set the JOG dial search FORWARD to the x5 position.
4. Adjust the variable VOLTS/DIV control of the
oscilloscope so that the maximum amplitude of the RF
waveform becomes the three DIVISIONs on the
oscilloscope.
5. Confirm that the RF waveform should be almost the
same amplitude with constant intervals as shown in
Fig.1.
6. Confirm that the RF waveform raises up within two
seconds at the specified amplitude when the mode is
changed from search FORWARD (x5) to PLAY.

3/5 Div
or less
3 Div

Fig.1

max.
4/5 Div
min.

3 Div

Specification : max. _ min. < 4/5 Div

DSR-2000/2000P

8-13

8-6. Search Reverse (x5) Waveform Check

x5) Waveform Check
8-6. Search Reverse (x
Basic knowledge

8-967-999-02
J-6444-610-B

Check procedure
1. Connect the oscilloscope as follows :
CH-1 : TP2 / DJ-461
CH-2 : TP3 / DJ-461
TRIG : CH-2
2. Insert the alignment tape XH2-1AST on the VTR.
3. Set the JOG dial search REVERSE to the x5 position.
4. Adjust the variable VOLTS/DIV control of the
oscilloscope so that the maximum amplitude of the RF
waveform becomes the three DIVISIONs on the
oscilloscope.
5. Confirm that the RF waveform should be almost the
same amplitude with constant intervals as shown in
Fig.1.
6. Confirm that the RF waveform raises up within two
seconds at the specified amplitude when the mode is
changed from search REVERSE (x5) to PLAY.

3/5 Div
or less
3 Div

Fig.1

max.
4/5 Div
3 Div

min.

Specification : max. _ min. < 4/5 Div

8-14

DSR-2000/2000P

8-7. RF Waveform Raiseup Check

8-7. RF Waveform Raiseup Check
Basic knowledge

8-967-999-02
J-6444-610-B

Check procedure
1. Connect the oscilloscope as follows :
CH-1 : TP2 / DJ-461
CH-2 : TP3 / DJ-461
TRIG : CH-2
2. Insert the alignment tape XH2-1AST on the VTR.
3. Confirm that the RF waveform raises up within two
seconds at the specified amplitude when the mode is
changed from EJECT → PLAY → EJECT → PLAY
repeatedly.
4. Confirm that the RF waveform raises up within two
seconds at the specified amplitude when the mode is
changed from FF → PLAY and from REW → PLAY.

DSR-2000/2000P

max.
4/5 Div
min.

3 Div

Specification : max. _ min. < 4/5 Div

8-15

8-8. Tape Curl Check at Tape Guide

8-8. Tape Curl Check at Tape Guide
Tools
. Alignment tape, XH2-1AST :
. Dental mirror :

8-967-999-02
J-6080-029-A

Check procedure
Confirm that tape runs at each tape guide as specified by the following figure when the unit put into the
modes of PLAY, FF, REW, search FORWARD x5 and search REVERSE x5 respectively.
Tape running condition
FWD

(
S4

Tension
regulator
S3

Capstan shaft

)
S2

Head drum

S reel

T reel

The hatched areas (marked by /////) are contacting with tape or pressing tape.

Tape running condition
Tape
guide

A
B
(Contact with upper flange) (Runs in the center)

C
D
(Contact with lower flange) (Curled)

E
(Folded)

F
(Dropped)

8-16

A : Contact with
upper flange

B : Runs in center

C : Contact with
lower flange

D : Curled

E : Folded

F : Dropped

DSR-2000/2000P

Section 9
Adjustment When Replacing Board
9-1. Adjustment/Check Items When Replacing Board
No adjustment is required for the board other than below.
Board name

Setting/Adj. after replacement
(Reference Section)

Contents

APR-45 board

10-2. Audio Adjustment

10-2-1. Audio OUTPUT Level Adjustment
10-2-2. Audio EE Level Adjustment

MS-64 board

5. Maintenance Menu

5-3-3. Servo Adjust
S/T-REEL & CAPSTAN Adjustment
TENTION Adjustment

6-2. Hours Meter

Initialize the Resetable Hours Meter

Operating Instructions
Chapter 6. Setup Menu

Resetting of Setup Menu Data

SV-212 board

5. Maintenance Menu

5-3-3. Servo Adjust
S/T-REEL & CAPSTAN Adjustment
TENTION Adjustment

SY-278 board

5. Maintenance Menu

5-3-1. Menu Data Control
MENU/SW DATA SAVE/LOAD

RP-111 board

5. Maintenance Menu

5-3-5. Electrical Adjust
PLL F0 Adjustment
EQ (DVCAM) Adjustment
EQ (DV) Adjustment

VPR-62 board

10-3. Video Adjustment

10-3-1. to 10-3-32.

DSR-2000/2000P

9-1

Section 10
Electrical Alignment
10-1. Electrical Alignment Overview
10-1-1. List of Adjustment Parts
APR-45
RV1
RV4
RV101
RV104
RV201
RV202
RV203
RV204
RV701
RV751
RV801
RV1501
RV1551

VPR-62
CH-1 EE Level ............................................ 10-3
CH-2 EE Level ............................................ 10-3
CH-3 EE Level ............................................ 10-3
CH-4 EE Level ............................................ 10-3
CH-1 OUTPUT Level ................................. 10-3
CH-2 OUTPUT Level ................................. 10-3
CH-3 OUTPUT Level ................................. 10-3
CH-4 OUTPUT Level ................................. 10-3
SDTI IN FREE RUN ................................. 10-33
SDTI OUT FREE RUN ............................. 10-33
SDI IN FREE RUN ................................... 10-33
SDI OUT FREE RUN ............................... 10-33
SDI OUT FREE RUN ............................... 10-33

DSR-2000/2000P

CT500
RV101
RV103
RV200
RV201
RV202
RV300
RV400
RV401
RV402
RV403
RV404
RV405
RV406
RV407
RV408
RV409
RV602
RV603
RV604
RV605
RV606
RV607
RV701
RV702
RV703
RV704
RV705
RV801
RV802
RV803
RV804
RV805
RV806
RV901
RV902
RV903
RV904
RV906
RV1001
RV1002

SPCK Error ................................................ 10-21
REC S VIDEO Chroma Level ................... 10-29
REC A/D Y Level ..................................... 10-26
REC COMPOSITE Y Level ...................... 10-27
REC COMPOSITE Chroma Level ............ 10-28
REC COMPOSITE Chroma Level ............ 10-28
COMPOSITE 4Fsc PLL DC ..................... 10-22
REC Y Level ............................................. 10-24
REC COMPONENT B-Y Level ............... 10-25
REC COMPONENT R-Y Level ............... 10-25
REC Y Clamp Level .................................. 10-23
REC COMPOSITE Y/B-Y Delay ............. 10-30
REC S VIDEO Y/B-Y Delay .................... 10-32
REC COMPONENT Y/B-Y Delay ........... 10-31
REC COMPOSITE Y/R-Y Delay ............. 10-30
REC S VIDEO Y/R-Y Delay .................... 10-32
REC COMPONENT Y/R-Y Delay ........... 10-31
PB COMPOSITE Y/C Delay .................... 10-16
PB COMPOSITE C/C Delay ..................... 10-15
PB COMPONENT Y/B-Y Delay .............. 10-17
COMPONENT B-Y OUT Level ................. 10-7
PB COMPONENT Y/R-Y Delay .............. 10-17
COMPONENT R-Y OUT Level ................. 10-8
ENC R-Y Level ......................................... 10-13
ENC B-Y Level ......................................... 10-13
ENC V SC Leak ........................................ 10-11
ENC U SC Leak ........................................ 10-11
PB Burst Level .......................................... 10-14
COMPONENT Y OUT Level ..................... 10-7
PB S VIDEO Chroma Level ...................... 10-15
VIDEO OUT 1 Video/Sync Level .............. 10-9
VIDEO OUT 1 Video/Sync Level .............. 10-9
COMPONENT Y OUT Level ..................... 10-7
VIDEO OUT 3 Y Level ............................ 10-10
REF. INT SCH Phase ................................ 10-20
U-V Axis (B-Y, R-Y) Phase ...................... 10-12
PB INT SCH Phase ................................... 10-18
REF. VIDEO OUT Sync Level ................. 10-19
REF. VIDEO OUT Burst Level ................ 10-19
HCK Frequency ........................................... 10-6
INT SC Frequency ...................................... 10-6

10-1

10-1. Electrical Alignment Overview
10-1-2. Measuring Equipment and Tools
10-1-3. Reference Tape for Alignment

10-1-2. Measuring Equipment and Tools
Type of measuring equipment

Equivalent

Remarks

Oscilloscope

Tektronix 2445

150 MHz or more

Video signal generator

TSG-130A (Op.02)

for NTSC

TSG-131A (Op.02)

for PAL

Waveform monitor

Tektronix 1760 Op. SC/1765 Op. SC

Audio signal generator

HP339A

Audio level meter

HP3400A/MeguroMN-446

Frequency counter

Advantest TR5821

Extension board

DJ-493 (J-6444-930-A)

Blank tape

DVM30ME, DVM30NME

On the market

10-1-3. Reference Tape for Alignment
XH5-1A2 (8-967-999-22) (for NTSC)
Recording contents are followings.
TIME CODE
(h) (m) (s)

REC
(s)

23 : 59 : 00

No Signal

75 % Full Color Bars

00 : 00

1 kHz

60 % Multi Burst

01 : 00

20 Hz

Bowtie with Mod 12.5T

02 : 00

14.5 kHz

02 : 30

10 kHz

03 : 00

No Signal

32 kHz

Cross Hatch (index)

03 : 30

1 kHz 0 dBFS

4 ch

Line 17

04 : 00

1 ch

75 % Full Color Bars

04 : 40

2 ch

05 : 20

3 ch

06 : 00

4 ch

06 : 40

06 : 45

60 % Multi Burst (for Composite)

06 : 50

1 kHz

Mod 12.5T

07 : 50

20 Hz

08 : 20

20 kHz

08 : 50

10 kHz

Cross Hatch (index)

09 : 20

1 kHz 0 dBFS

Chroma Noise

09 : 50

Line 17

10 : 20

75 % Full Color Bars

10 : 50

180

48 kHz

60 % Multi Burst

13 : 50

2 ch

Mod 12.5T

14 : 50

Shallow Ramp

15 : 20

75 % Full Color Bars

16 : 20

100

75 % Full Color Bars (R-Y OFF)

18 : 00

180

75 % Full Color Bars (B-Y OFF)

21 : 00

180

Blanking Marker

24 : 00

180

Line 17 (R-Y OFF)

27 : 00

180

Line 17 (B-Y OFF)

30 : 00

180

VIDEO
Black Burst

Shallow Ramp

Quad Phase
Black Burst

Shallow Ramp (B-Y/R-Y OFF)

AUDIO

1 kHz

No Signal

1 kHz

*1 Audio levels are _20 dBFS (Reference), except 1 kHz 0 dBFS part.

10-2

DSR-2000/2000P

10-1. Electrical Alignment Overview
10-1-3. Reference Tape for Alignment

XH5-1AP2 (8-967-999-26) (for PAL)
Recording contents are followings.
TIME CODE
(h) (m) (s)

REC
(s)

23 : 59 : 00

No Signal

100 % Full Color Bars

00 : 00

1 kHz

60 % Multi Burst

01 : 00

20 Hz

Bowtie with Mod 10T

02 : 00

14.5 kHz

02 : 30

10 kHz

03 : 00

No Signal

32 kHz

Cross Hatch (index)

03 : 30

1 kHz 0 dBFS

4 ch

Line 17

04 : 00

1 ch

100 % Full Color Bars

04 : 40

2 ch

05 : 20

3 ch

06 : 00

4 ch

06 : 40

06 : 45

60 % Multi Burst (for Composite)

06 : 50

1 kHz

Mod 10T

07 : 50

20 Hz

08 : 20

20 kHz

08 : 50

10 kHz

Cross Hatch (index)

09 : 20

1 kHz 0 dBFS

Chroma Noise

09 : 50

Line 17

10 : 20

100 % Full Color Bars

10 : 50

180

48 kHz

60 % Multi Burst

13 : 50

2 ch

Mod 10T

14 : 50

Shallow Ramp

15 : 20

100 % Full Color Bars

16 : 20

100

100 % Full Color Bars (R-Y OFF)

18 : 00

180

100 % Full Color Bars (B-Y OFF)

21 : 00

180

Blanking Marker

24 : 00

180

Line 17 (R-Y OFF)

27 : 00

180

Line 17 (B-Y OFF)

30 : 00

180

VIDEO
Black Burst

Shallow Ramp

Quad Phase
Black Burst

Shallow Ramp (B-Y/R-Y OFF)

AUDIO

1 kHz

No Signal

1 kHz

*1 Audio levels are _18 dBFS (Reference), except 1 kHz 0 dBFS part.

DSR-2000/2000P

10-3

10-2. Audio Adjustment
10-2-1. Audio OUTPUT Level Adjustment

10-2. Audio Adjustment
10-2-1. Audio OUTPUT Level Adjustment
Conditions for adjustment
. MENU
ENHANCED
↓
AU REF LEVEL ; _20 dB (for NTSC)
_18 dB (for PAL)
OUTPUT LEVEL ; +4 dB
VIDEO INPUT SELECT ; SG
AUDIO INPUT SELECT ; SG
. AUDIO REC & PB AUDIO VR/
Control panel ; PRESET
. PB mode
1 kHz Ref. level (32 kHz ; 4CH)/SG (1 kHz)

Specification

Adjustment

AUDIO OUTPUT 1/3 & 2/4 (600 Z loaded)
CH-1 ;
1RV201/APR-45 (L-1)
CH-2 ;
1RV202/APR-45 (L-1)
CH-3 ;
1RV203/APR-45 (L-1)
CH-4 ;
1RV204/APR-45 (M-1)

Spec. +4.0 ± 0.1 dBm

10-2-2. Audio EE Level Adjustment
Conditions for adjustment
. MENU
ENHANCED
↓
AU REF LEVEL ; _20 dB (for NTSC)
_18 dB (for PAL)
OUTPUT LEVEL ; +4 dB
VIDEO INPUT SELECT ; SG
AUDIO INPUT SELECT ; ANALOG
. AUDIO REC & PB AUDIO VR/
Control panel ; PRESET
. AUDIO INPUT CH-1/CH-2/CH-3/CH-4 ;
1 kHz, +4 dBu
. EE mode

10-4

Specification

Adjustment

AUDIO OUTPUT 1/3 & 2/4 (600 Z loaded)
CH-1 ;
1RV1/APR-45 (M-3)
CH-2 ;
1RV4/APR-45 (N-3)
CH-3 ;
1RV101/APR-45 (P-3)
CH-4 ;
1RV104/APR-45 (P-3)

Spec. +4.0 ± 0.3 dBm

DSR-2000/2000P

10-3. Video Adjustment

10-3. Video Adjustment
[Switch Setting]
For NTSC
This setting should be fixed in position unless otherwise specified.
LOCAL/REMOTE
; LOCAL
PROCESS CONTROL ; LOCAL
CHARACTER
; ON
VIDEO

MENU ITEM 713-1, INPUT LEVEL ; 0.0 %
CHROMA 

MENU ITEM 713-2, OUTPUT LEVEL ; 0.0 %
SET UP
 ; PRESET
Y/C DELAY 

HUE

For PAL
LOCAL/REMOTE
CHARACTER
PROCESS CONTROL


VIDEO
 ; PRESET
Y/C DELAY 

; LOCAL
; ON
; LOCAL

[Connection]
Connect some equipment as following unless otherwise specified.
(Connection 1)
DSR-2000/2000P
Oscilloscope

TP
COMPONENT IN

Video signal generator
(NTSC : TSG-130A)
(PAL : TSG-131A)
BB

REF. VIDEO IN
(75 Z : OFF)

CH-1
CH-2
CH-3

COMPONENT OUT

EXT REF
WFM or Oscilloscope
(Terminated at 75 Z)

(Connection 2)
DSR-2000/2000P
Oscilloscope

TP
VIDEO IN (75 Z : ON)
S VIDEO IN

Video signal genelator
(NTSC : TSG-130A)
(PAL : TSG-131A)
BB

REF. VIDEO IN
(75 Z : OFF)

(VIDEO OUT 3)
(VIDEO OUT 2)
REF.VIDEO OUT
S VIDEO OUT
VIDEO OUT 1

WFM
A

EXT REF

DSR-2000/2000P

10-5

10-3. Video Adjustment
10-3-1. INT SC Frequency Adjustment

10-3-1. INT SC Frequency Adjustment
Conditions for adjustment
Oscilloscope or voltmeter
. STOP mode

Specification

Adjustment

1 Mesure the voltage (Vo) at TP1003/
VPR-62 (H-4).
2 Measure the voltage at the center terminal
of RV1002.

1RV1002/VPR-62 (G-4)

RV1002

Voltage measuring point

Spec. V = Vo ± 0.1 Vdc

Connection 1

10-3-2. HCK Frequency Adjustment
(Connection)
DSR-2000/2000P
Frequency counter

Oscilloscope

VIDEO IN
Video signal generator
REF. VIDEO IN
(NTSC : TSG-130A)
No. REF.
(PAL : TSG-131A)

Conditions for adjustment
Frequency counter
. STOP mode
. REF. VIDEO IN ; No signal
. VIDEO IN Select ; Composite
. VIDEO IN ; No signal

10-6

Specification
TP1004/VPR-62 (G-4)

Adjustment
1RV1001/VPR-62 (G-4)

Spec. f = 13,500,000 ± 35 Hz

DSR-2000/2000P

10-3. Video Adjustment
10-3-3. COMPONENT Y OUT Level Adjustment
10-3-4. COMPONENT B-Y OUT Level Adjustment

10-3-3. COMPONENT Y OUT Level Adjustment
Conditions for adjustment
[For NTSC]
WFM or Oscilloscope
. MENU ITEM 713-2, OUTPUT LEVEL ; 7.5 %
. PB mode
75 % Color bars/XH5-1A2

Specification

Adjustment

COMPONENT Y OUT (75 Z terminated)
1RV801/VPR-62 (M-4)
1RV805/VPR-62 (L-4)

(A) Y/S-Y Level
(B) Y/S-Y SYNC
TRIG : REF. VIDEO

[For PAL]
WFM or Oscilloscope
. PB mode
100 % Color bars/XH5-1AP2

Connection 1

Spec.
[For NTSC]
A = 0.714
B = 0.286
[For PAL]
A = 0.700
B = 0.300

± 0.007 V (100 ± 1 IRE)
± 0.003 V (40 ± 0.5 IRE)
± 0.007 V
± 0.003 V

10-3-4. COMPONENT B-Y OUT Level Adjustment
Conditions for adjustment
[For NTSC]
WFM or Oscilloscope
. MENU ITEM 713-2, OUTPUT LEVEL ; 7.5 %
. PB mode
75 % Color bars/XH5-1A2

Specification
COMPONENT B-Y OUT (75 Z terminated)

Adjustment
1RV605/VPR-62 (K-4)

TRIG : REF. VIDEO

[For PAL]
WFM or Oscilloscope
. PB mode
100 % Color bars/XH5-1AP2

Connection 1

DSR-2000/2000P

Spec.
[For NTSC]
A = 0.700 ± 0.007 V (98 ± 1 IRE)
[For PAL]
A = 0.700 ± 0.700 V

10-7

10-3. Video Adjustment
10-3-5. COMPONENT R-Y OUT Level Adjustment
10-3-6. SETUP OFF Chroma Level Check

10-3-5. COMPONENT R-Y OUT Level Adjustment
Conditions for adjustment
[For NTSC]
WFM or Oscilloscope
. MENU ITEM 713-2, OUTPUT LEVEL ; 7.5 %
. PB mode
75 % Color bars/XH5-1A2

Specification
COMPONENT R-Y OUT (75 Z terminated)

Adjustment
1RV607/VPR-62 (K-3)

TRIG : REF. VIDEO

[For PAL]
WFM or Oscilloscope
. PB mode
100 % Color bars/XH5-1AP2

Connection 1

Spec.
[For NTSC]
A = 0.700 ± 0.007 V p-p (98 ± 1 IRE)
[For PAL]
A = 0.700 ± 0.007 V p-p

10-3-6. SETUP OFF Chroma Level Check (NTSC only)
Conditions for adjustment
WFM or Oscilloscope
. PB mode
75 % Color bars/XH5-1A2

Specification

Adjustment

COMPONENT R-Y OUT (75 Z terminated)
TRIG : REF. VIDEO

n
Check that MENU ITEM 713-2,
OUTPUT LEVEL ; 0.0 %

Connection 1

10-8

Spec. A = 0.757 ± 0.007 V p-p (106 ± 1 IRE)

DSR-2000/2000P

10-3. Video Adjustment
10-3-7. S VIDEO OUT Y Level Check
10-3-8. VIDEO OUT 1 Video/Sync Level Adjustment

10-3-7. S VIDEO OUT Y Level Check
Conditions for adjustment
WFM or Oscilloscope
. PB mode
75 % Color bars/XH5-1A2 (for NTSC)
100 % Color bars/XH5-1AP2 (for PAL)

Specification

Adjustment

S VIDEO (Y) OUT (75 Z terminated)
TRIG : REF. VIDEO

Connection 2

Spec.
[For NTSC]
A = 0.714 ± 0.007 V (100 ± 1 IRE)
[For PAL]
A = 0.700 ± 0.007 V

10-3-8. VIDEO OUT 1 Video/Sync Level Adjustment
Conditions for adjustment
WFM or Oscilloscope
. PB mode
75 % Color bars/XH5-1A2 (for NTSC)
100 % Color bars/XH5-1AP2 (for PAL)

Specification

Adjustment

VIDEO OUT 1 (75 Z terminated)
1RV803/VPR-62 (M-4)
1RV804/VPR-62 (L-4)

(A) Video Level
(B) Sync Level
TRIG : REF. VIDEO

Connection 2

DSR-2000/2000P

Spec.
[For NTSC]
A = 0.714
B = 0.286
[For PAL]
A = 0.700
B = 0.300

± 0.007 V (100 ± 1 IRE)
± 0.003 V (40 ± 0.5 IRE)
± 0.007 V
± 0.003

10-9

10-3. Video Adjustment
10-3-9. VIDEO OUT 2 Video Level Check
10-3-10. VIDEO OUT 3 Y Level Adjustment

10-3-9. VIDEO OUT 2 Video Level Check
Conditions for adjustment
WFM or Oscilloscope
. PB mode
75 % Color bars/XH5-1A2 (for NTSC)
100 % Color bars/XH5-1AP2 (for PAL)

Specification

Adjustment

VIDEO OUT 2 (75 Z terminated)
TRIG : REF. VIDEO

Connection 2

Spec.
[For NTSC]
A = 0.714 ± 0.007 V (100 ± 1 IRE)
[For PAL]
A = 0.700 ± 0.007 V

10-3-10. VIDEO OUT 3 Y Level Adjustment
Conditions for adjustment
WFM or Oscilloscope
. PB mode
75 % Color bars/XH5-1A2 (for NTSC)
100 % Color bars/XH5-1AP2 (for PAL)

Specification
VIDEO OUT 3 (75 Z terminated)

Adjustment
1RV806/VPR-62 (L-4)

TRIG : REF. VIDEO

Connection 2

10-10

Spec.
[For NTSC]
A = 0.714 ± 0.007 V (100 ± 1 IRE)
[For PAL]
A = 0.700 ± 0.007 V

DSR-2000/2000P

10-3. Video Adjustment
10-3-11. ENC SC Leak Adjustment

10-3-11. ENC SC Leak Adjustment
Conditions for adjustment
Step 1
. PB mode
75 % Color bars/XH5-1A2 (for NTSC)
100 % Color bars/XH5-1AP2 (for PAL)
. Set the time axis of the WFM to magnification mode

Specification

Adjustment

VIDEO OUT 1 (75 Z terminated)
1RV703/VPR-62 (D-1)
1RV704/VPR-62 (D-1)

(A) V SC Leak
(B) U SC Leak
TRIG : REF. VIDEO
WFM

(Spec. Adjust the A and B alternately.)

Connection 2
Step 2 (Check)
. PB mode
75 % Color bars/XH5-1A2 (for NTSC)
100 % Color bars/XH5-1AP2 (for PAL)

Spec. Minimize the A, B.
A, B < 0.007 V (1 IRE)
VIDEO OUT 1 (75 Z terminated)
TRIG : REF. VIDEO
Vector

Connection 2
DSR-2000/2000P

Spec. Maximum the gain of the Vector and
check the dot is at center.

10-11

10-3. Video Adjustment
10-3-12. U-V Axis (B-Y, R-Y) Phase Adjustment

10-3-12. U-V Axis (B-Y, R-Y) Phase Adjustment
Conditions for adjustment

Specification

. PB mode

VIDEO OUT 1 (75 Z terminated)

[Flow]
(A) Burst preset
. PB mode
Quad Phase/XH5-1A2 or XH5-1AP2
(05:20-06:00)

(A) Burst preset

(B) V-axis phase adjustment
. PB mode
Quad Phase/XH5-1A2 or XH5-1AP2
(05:20-06:00)

Adjustment

1PHASE control/Vector
1RV902/VPR-62 (F-1)

(B) V-axis (U/V OFFSET)
TRIG : REF. VIDEO
Vector
(Before adjustment)

Burst

(After Adjustment)

Connection 2

10-12

Spec. (A) Set the dot of the burst in the right
position on the scale.
(B) Set the dots of the R-Y on the V
axis of the vector.
C = 0 ± 0.5 d

DSR-2000/2000P

10-3. Video Adjustment
10-3-13. PB VIDEO OUT 1 Chroma/Burst Level Adjustment

10-3-13. PB VIDEO OUT 1 Chroma/Burst Level Adjustment
Conditions for adjustment

Specification

Adjustment

WFM or Oscilloscope
. PB mode
75 % Color bars/XH5-1A2 (for NTSC)
100 % Color bars/XH5-1AP2 (for PAL)

VIDEO OUT 1 (75 Z terminated)
Step 1 Chroma Level
(A) Burst preset

1PHASE control/Vector

n
The “Setup ON/OFF” setting of the DSR2000 and that a vectorscope must have
been set to the same position beforehand.

(B) ENC R-Y LEVEL
ENC B-Y LEVEL

1RV701/VPR-62 (D-1)
1RV702/VPR-62 (C-1)

TRIG : REF. VIDEO
Vector (for NTSC)

Vector (for PAL)

Connection 2

DSR-2000/2000P

Spec. (A) Set the dot of the burst in the right
position on the scale.
(B) All dots should be inside the “4”
mark on the vector by adjustment
RV200 and RV201 alternately.

10-13

10-3. Video Adjustment
10-3-13. PB VIDEO OUT 1 Chroma/Burst Level Adjustment

Conditions for adjustment
WFM or Oscilloscope
. PB mode
75 % Color bars/XH5-1A2 (for NTSC)
100 % Color bars/XH5-1AP2 (for PAL)

Connection 2

10-14

Specification
Step 2 Burst Level

Adjustment
1RV705/VPR-62 (D-2)

TRIG : REF. VIDEO

Spec.
[For NTSC]
A = 0.286 ± 0.003 V (40 ± 0.5 IRE)
[For PAL]
A = 0.300 ± 0.003 V

DSR-2000/2000P

10-3. Video Adjustment
10-3-14. PB S VIDEO Chroma Level Adjustment
10-3-15. PB COMPOSITE C/C Delay Adjustment

10-3-14. PB S VIDEO Chroma Level Adjustment
Conditions for adjustment
WFM or Oscilloscope
. MENU ITEM 713-2, OUTPUT LEVEL ; 7.5 %
. PB mode
75 % Color bars/XH5-1A2 (for NTSC)
100 % Color bars/XH5-1AP2 (for PAL)

Connection 2

Specification
S VIDEO (C) OUT (75 Z terminated)

Adjustment
1RV802/VPR-62 (N-5)

TRIG : REF. VIDEO

Spec.
[For NTSC]
A = 0.627 ± 0.007 V p-p (87.7 ± 1 IRE)
[For PAL]
A = 0.885 ± 0.006 V p-p

10-3-15. PB COMPOSITE C/C Delay Adjustment
Conditions for adjustment
Oscilloscope
Vertical mode : INV +ADD
. PB mode
Bowtie/XH5-1A2 or XH5-1AP2
(02:00-02:30)

Specification
CH-1/Oscilloscope
TP602/VPR-62 (D-2)
CH-2/Oscilloscope
TP603/VPR-62 (D-1)

Adjustment
1RV603/VPR-62 (B-1)

Spec. Minimize

Connection 2

DSR-2000/2000P

10-15

10-3. Video Adjustment
10-3-16. PB COMPOSITE Y/C Delay Adjustment

10-3-16. PB COMPOSITE Y/C Delay Adjustment
Conditions for adjustment
. PB mode
Mod 12.5T/XH5-1A2 or XH5-1AP2
(07:50-08:20)

Specification
VIDEO OUT 1 (75 Z terminated)

Adjustment
1RV602/VPR-62 (B-1)

TRIG : INT/WFM
WFM

Connection 2

10-16

DSR-2000/2000P

10-3. Video Adjustment
10-3-17. PB COMPONENT Y/C Delay Adjustment

10-3-17. PB COMPONENT Y/C Delay Adjustment
[Connection for reference] Using for an oscilloscope
DSR-2000/2000P
(B)
COMPONENT R-Y OUT
CH-2
COMPONENT B-Y OUT
Oscilloscope
(A)
CH-1
COMPONENT Y OUT

INV/ADD mode
TRIG : CH-1

(A) 1RV308
(B) 1RV309

Conditions for adjustment
. PB mode
Bowtie/XH5-1A2 or XH5-1AP2
(02:00-02:30)

Specification

Adjustment

COMPONENT OUT (75 Z terminated)
(A) B-Y Delay
(B) R-Y Delay

1RV604/VPR-62 (J-4)
1RV606/VPR-62 (J-3)
TRIG : INT/WFM
Bowtie mode

Connection 1

DSR-2000/2000P

Spec. Set the each Bowtie dip point of (A)
and (B) on the center marker.
0 ± 20 ns

10-17

10-3. Video Adjustment
10-3-18. PB INT SCH Phase Adjustment

10-3-18. PB INT SCH Phase Adjustment
Conditions for adjustment
. PB mode
75 % Color bars/XH5-1A2 (for NTSC)
100 % Color bars/XH5-1AP2 (for PAL)
. REF. VIDEO INPUT ; No signal

Specification

Adjustment

VIDEO OUT 1 (75 Z terminated)
1PHASE control/Vector
1RV903/VPR-62 (F-1)

(A) Burst Preset
(B) INT SC
TRIG : INT/WFM
SCH mode

. AFTER ADJUSTMENT IS COMPLETED,
RE-CONNECT THE REF. VIDEO INPUT.

Connection 2

10-18

Spec. (A) Set the dot of the burst in the right
position on the scale.
(B) The SYNC should be in the same
phase as the burst (SCH = 0 d).

DSR-2000/2000P

10-3. Video Adjustment
10-3-19. REF. VIDEO OUT Sync/Burst Level Adjustment

10-3-19. REF. VIDEO OUT Sync/Burst Level Adjustment
Conditions for adjustment
WFM or Oscilloscope
. PB mode
75 % Color bars/XH5-1A2 (for NTSC)
100 % Color bars/XH5-1AP2 (for PAL)
. REF. VIDEO INPUT ; No signal

Specification

Adjustment

REF. VIDEO OUT (75 Z terminated)
(A) Sync Level
(B) Burst Level

1RV904/VPR-62 (L-3)
1RV906/VPR-62 (M-3)

TRIG : INT/WFM

. AFTER ADJUSTMENT IS COMPLETED,
RE-CONNECT THE REF. VIDEO INPUT.

Connection 2

DSR-2000/2000P

Spec.
[For NTSC]
A, B = 0.286 ± 0.003 V (40 ± 0.5 IRE)
[For PAL]
A, B = 0.300 ± 0.003 V

10-19

10-3. Video Adjustment
10-3-20. REF. INT SCH Phase Adjustment

10-3-20. REF. INT SCH Phase Adjustment
Conditions for adjustment
. PB mode
75 % Color bars/XH5-1A2 (for NTSC)
100 % Color bars/XH5-1AP2 (for PAL)
. REF. VIDEO INPUT ; No signal

Specification

Adjustment

REF. VIDEO OUT (75 Z terminated)
1PHASE control/Vector
1RV901/VPR-62 (L-3)

(A) Burst Preset
(B) Sync Phase
TRIG : INT/WFM
SCH mode

. AFTER ADJUSTMENT IS COMPLETED,
RE-CONNECT THE REF. VIDEO INPUT.

Connection 2

10-20

Spec. (A) Set the dot of the burst in the right
position on the scale.
(B) The SYNC should be in the same
phase as the burst. (SCH = 0 ± 3 d)

DSR-2000/2000P

10-3. Video Adjustment
10-3-21. SPCK Error Adjustment

10-3-21. SPCK Error Adjustment
(Connection)

Video signal generator
(NTSC : TSG-130A)
(PAL : TSG-131A)

75 % CB (NTSC)
100 % CB (PAL)

Conditions for adjustment
Oscilloscope
. EE mode
. VIDEO IN ; 75 % Color bars (for NTSC)
100 % Color bars (for PAL)

DSR-2000/2000P
VIDEO IN

REF VIDEO IN

Specification
TP500/VPR-62 (A-3)

Adjustment
1CT500/VPR-62 (A-4)

Spec. A = 1.5 ± 0.1 V dc

DSR-2000/2000P

10-21

10-3. Video Adjustment
10-3-22. COMPOSITE 4Fsc PLL DC Check/Adjustment

10-3-22. COMPOSITE 4Fsc PLL DC Check/Adjustment
Conditions for adjustment
Oscilloscope
. EE mode
. VIDEO IN ; 75 % Color bars (for NTSC)
100 % Color bars (for PAL)
. VIDEO IN select/MENU ; COMPOSITE

Specification

Adjustment

TP301/VPR-62 (P-2)
[Check]

Spec. A = 2.5 ± 0.5 V dc
TP300/VPR-62 (P-2)

Connection 1

10-22

1RV300/VPR-62 (P-2)

Spec. A = 2.5 ± 0.5 V dc

DSR-2000/2000P

10-3. Video Adjustment
10-3-23. REC Y Clamp Level Adjustment

10-3-23. REC Y Clamp Level Adjustment
Conditions for adjustment
WFM or Oscilloscope
. EE mode
. COMPONENT IN ; Pluse & Bar

Specification
COMPONENT Y OUT (75 Z terminated)

Adjustment
1RV403/VPR-62 (J-2)

n
Check that only NTSC MENU ITEM 713-1,
INPUT
LEVEL ; 0.0 %

Connection 1

DSR-2000/2000P

Spec. A = Minimize the level difference A at
setup.

10-23

10-3. Video Adjustment
10-3-24. REC Y Level Adjustment

10-3-24. REC Y Level Adjustment
Conditions for adjustment
WFM or Oscilloscope
. EE mode
. COMPONENT IN ;
75 % Color bars (for NTSC)
100 % Color bars (for PAL)

Connection 1

10-24

Specification
COMPONENT Y OUT (75 Z terminated)

Adjustment
1RV400/VPR-62 (J-2)

TRIG : REF. VIDEO

Spec.
[For NTSC]
A = 0.714 ± 0.007 V (100 ± 1 IRE)
[For PAL]
A = 0.700 ± 0.007 V

DSR-2000/2000P

10-3. Video Adjustment
10-3-25. REC COMPONENT R-Y Level Adjustment
10-3-26. REC COMPONENT B-Y Level Adjustment

10-3-25. REC COMPONENT R-Y Level Adjustment
Conditions for adjustment
WFM or Oscilloscope
. EE mode
. COMPONENT IN ;
75 % Color bars (for NTSC)
100 % Color bars (for PAL)

Connection 1

Specification
COMPONENT R-Y OUT (75 Z terminated)

Adjustment
1RV402/VPR-62 (K-2)

TRIG : REF. VIDEO

Spec.
[For NTSC]
A = 0.700 ± 0.007 V p-p (98 ± 1 IRE)
[For PAL]
A = 0.700 ± 0.007 V p-p

10-3-26. REC COMPONENT B-Y Level Adjustment
Conditions for adjustment
WFM or Oscilloscope
. EE mode
. COMPONENT IN ;
75 % Color bars (for NTSC)
100 % Color bars (for PAL)

Connection 1

DSR-2000/2000P

Specification
COMPONENT B-Y OUT (75 Z terminated)

Adjustment
1RV401/VPR-62 (K-1)

TRIG : REF. VIDEO

Spec.
[For NTSC]
A = 0.700 ± 0.007 V p-p (98 ± 1 IRE)
[For PAL]
A = 0.700 ± 0.007 V p-p

10-25

10-3. Video Adjustment
10-3-27. REC A/D Y Level Adjustment

10-3-27. REC A/D Y Level Adjustment
(Connection)
DSR-2000/2000P

Video signal generator
(NTSC : TSG-130A)
(PAL : TSG-131A)

75 % CB (for NTSC)
100 % CB (for PAL)

Conditions for adjustment
WFM or Oscilloscope
. EE mode
. VIDEO IN ; 75 % Color bars (for NTSC)
100 % Color bars (for PAL)
. VIDEO IN select/MENU ; COMPOSITE
. S101-1/SV-212 (L-1) ; ON
. S200/VPR-62 (M-1) ; ON

. After Adjustment, S101-1, S200 ; OFF

10-26

WFM or Oscilloscope
VIDEO IN

COMPONENT
Y OUT

REF VIDEO IN

Specification
COMPONENT Y OUT (75 Z terminated)

Adjustment
1RV103/VPR-62 (P-5)

TRIG : REF. VIDEO

Spec.
[For NTSC]
A = 0 ± 0.007 V (0 ± 1 IRE)
[For PAL]
A = 0 ± 0.007 V

DSR-2000/2000P

10-3. Video Adjustment
10-3-28. REC COMPOSITE Y Level Adjustment

10-3-28. REC COMPOSITE Y Level Adjustment
Conditions for adjustment
WFM or Oscilloscope
. EE mode
. VIDEO IN ; 75 % Color bars (for NTSC)
100 % Color bars (for PAL)
. VIDEO IN select/MENU ; COMPOSITE

Specification
VIDEO OUT 1 (75 Z terminated)

Adjustment
1RV200/VPR-62 (L-1)

TRIG : REF. VIDEO

Connection 2

DSR-2000/2000P

Spec.
[For NTSC]
A = 0.714 ± 0.007 V (100 ± 1 IRE)
[For PAL]
A = 0.700 ± 0.007 V

10-27

10-3. Video Adjustment
10-3-29. REC COMPOSITE Chroma Level Adjustment

10-3-29. REC COMPOSITE Chroma Level Adjustment
Conditions for adjustment
. EE mode
. VIDEO IN ; 75 % Color bars (for NTSC)
100 % Color bars (for PAL)
. VIDEO IN select/MENU ; COMPOSITE
n
The “Setup ON/OFF” setting of the DSR2000 and that a vectorscope must have
been set to the same position beforehand.

Specification

Adjustment

VIDEO OUT 1 (75 Z terminated)
(A) Burst
(B) Composite Chroma Level

1PHASE control/Vector
1RV201/VPR-62 (L-1)
1RV202/VPR-62 (M-1)

TRIG : REF. VIDEO
Vector (for NTSC)

Vector (for PAL)

Connection 2

10-28

Spec. (A) Set the dot of the burst in the right
position on the scale.
(B) All dots should be inside the “4”
mark on the vector.

DSR-2000/2000P

10-3. Video Adjustment
10-3-30. REC S VIDEO Chroma Level Adjustment

10-3-30. REC S VIDEO Chroma Level Adjustment
Conditions for adjustment
. EE mode
. S VIDEO IN ; 75 % Color bars (for NTSC)
100 % Color bars (for PAL)
. VIDEO IN select/MENU ; S VIDEO
n
The “Setup ON/OFF” setting of the DSR2000 and that a vectorscope must have
been set to the same position beforehand.

Specification

Adjustment

S VIDEO (C) OUT (75 Z terminated)
1PHASE control/Vector
1RV101/VPR-62 (P-6)

(A) Burst
(B) S-C Level
TRIG : REF. VIDEO
Vector (for NTSC)

Vector (for PAL)

Connection 2

DSR-2000/2000P

Spec. (A) Set the dot of the burst in the right
position on the scale.
(B) All dots should be inside the “4”
mark on the vector.

10-29

10-3. Video Adjustment
10-3-31. REC COMPOSITE Y/C Delay Adjustment

10-3-31. REC COMPOSITE Y/C Delay Adjustment
(Connection)
DSR-2000/2000P
BB
Video signal generator
(NTSC : TSG-130A)
(PAL : TSG-131A)
COMPOSITE

REF. VIDEO IN

VIDEO IN
Oscilloscope

COMPONENT OUT

Y
B-Y
R-Y

CH-1
CH-2
TRIG

Conditions for adjustment
. EE mode
. VIDEO IN ; 75 % Color bars (for NTSC)
100 % Color bars (for PAL)
. VIDEO IN select/MENU ; COMPOSITE

Specification

Adjustment

COMPONENT OUT (75 Z terminated)
B-Y

B-Y : 1RV404/VPR-62
(K-1)
R-Y : 1RV407/VPR-62
(K-2)

A portion

R-Y

A portion
(Detail of A portion)
Y

50% Level point
B-Y
R-Y

Spec. 0 ± 20 ns

10-30

DSR-2000/2000P

10-3. Video Adjustment
10-3-32. REC COMPONENT Y/C Delay Adjustment

10-3-32. REC COMPONENT Y/C Delay Adjustment
[Connection for reference] Using for an oscilloscope
DSR-2000/2000P
(B)

COMPONENT R-Y OUT

CH-2
Oscilloscope

COMPONENT B-Y OUT
(A)

CH-1

INV/ADD mode
TRIG : CH-1

COMPONENT Y OUT
(A) 1RV406
(B) 1RV409

Conditions for adjustment
. EE mode
. COMPONENT IN ; Bowtie

Specification

Adjustment

COMPONENT OUT (75 Z terminated)
(A) B-Y Delay
(B) R-Y Delay

1RV406/VPR-62 (K-1)
1RV409/VPR-62 (K-2)
TRIG : INT/WFM
Bowtie mode

Connection 1

DSR-2000/2000P

Spec. Set the each Bowtie dip point of (A)
and (B) on the center marker.
0 ± 20 ns

10-31

10-3. Video Adjustment
10-3-33. REC S VIDEO Y/C Delay Adjustment

10-3-33. REC S VIDEO Y/C Delay Adjustment
(Connection)
DSR-2000/2000P
BB
Video signal generator
(NTSC : TSG-130A)
(PAL : TSG-131A)
S

REF. VIDEO IN

S VIDEO IN
Oscilloscope

COMPONENT OUT

Y
B-Y
R-Y

CH-1
CH-2
TRIG

Specification

Conditions for adjustment
. EE mode
. S VIDEO IN ; 75 % Color bars (for NTSC)
100 % Color bars (for PAL)
. VIDEO IN select/MENU ; S VIDEO

COMPONENT OUT (75 Z terminated)
B-Y

Adjustment
B-Y : 1RV405/VPR-62
(K-1)
R-Y : 1RV408/VPR-62
(K-2)

A portion

R-Y

A portion
(Detail of A portion)
Y

50% Level point
B-Y
R-Y

Spec. 0 ± 20 ns

10-32

DSR-2000/2000P

10-4. SDI/SDTI
10-4-1. Free Run Adjustment

10-4. SDI/SDTI
10-4-1. Free Run Adjustment
(Connection)
DSR-2000/2000P

Oscilloscope

Frequency counter

APR-45 (TP)

Conditions for adjustment
Step 1
. E-E mode
. Connect jumper wire between TP1501/
APR-45 (C-2) and E704/APR-45 (A-1).
. After adjustment, remove jumper wire.
Step 2
. E-E mode
. Connect jumper wire between TP1551/
APR-45 (E-2) and E1501/APR-45 (E-1).
. After adjustment, remove jumper wire.
. E-E mode
. Connect jumper wire between TP801/
APR-45 (B-1) and E704/APR-45 (A-1).
. Select SDTI with INPUT SELECT.

Specification
TP751/APR-45 (A-1)
TP1502/APR-45 (E-1)

DSR-2000/2000P

1RV751/APR-45 (A-1)
1RV1501/APR-45 (A-1)

Spec. 27.0 ± 0.1 MHz
TP1552/APR-45 (E-1)

1RV1551/APR-45 (F-1)

Spec. 27.0 ± 0.1 MHz
Step 1
TP701/APR-45 (A-2)

1RV701/APR-45 (A-2)

Spec. 27.0 ± 0.1 MHz
Step 2
TP802/APR-45 (B-4)

. After adjustment, remove jumper wire.

Adjustment

1RV801/APR-45 (C-2)

Spec. 27.0 ± 0.1 MHz

10-33

SAFETY CHECK-OUT
After correcting the original service problem,
perform the following safety checks before
releasing the set to the customer :
Check the metal trim, “metallized” knobs, screws,
and all other exposed metal parts for AC
leakage. Check leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to
earth ground and from all exposed metal parts to
any exposed metal part having a return to
chassis, must not exceed 0.5 mA. Leakage
current can be measured by any one of three
methods.
1. A commercial leakage tester, such as the
Simpson 229 or RCA WT-540A. Follow the
manufacturers’ instructions to use these
instruments.
2. A battery-operated AC milliammeter. The
Data Precision 245 digital multimeter is
suitable for this job.
3. Measuring the voltage drop across a resistor
by means of a VOM or battery-operated AC
voltmeter. The “limit” indication is 0.75 V, so
analog meters must have an accurate lowvoltage scale. The Simpson 250 and Sanwa
SH-63Trd are examples of a passive VOM
that is suitable. Nearly all battery operated
digital multimeters that have a 2 V AC range
are suitable. (See Fig. A)

To Exposed Metal
Parts on Set

0.15 µF

1.5 kZ

AC
voltmeter
(0.75V)

Earth Ground
Fig A. Using an AC voltmeter to check AC leakage.

DSR-2000/2000P

DSR-2000 (UC)
DSR-2000P (CE) E
9-955-186-12

Sony Corporation
B&P Company

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : Yes
Encryption                      : Standard V1.2 (40-bit)
User Access                     : Print, Copy, Annotate, Fill forms, Extract, Assemble, Print high-res
Create Date                     : 2001:06:15 19:32:51
Producer                        : Acrobat Distiller 4.0.5  for Macintosh
Modify Date                     : 2001:06:16 12:20:28+09:00
Title                           : DSR-2000 Service Manual Volume 1
Author                          : SONY CSNC DD
Page Count                      : 344
Page Mode                       : UseOutlines
Page Layout                     : SinglePage

EXIF Metadata provided by EXIF.tools

DSR 2000 Service Manual Volume 1 DSR2000_VOL1 DSR2000 VOL1

Navigation menu

Versions of this User Manual:

Views

Navigation