RRV3451 DV 696AV S

User Manual: DV-696AV-S

Open the PDF directly: View PDF PDF.
Page Count: 82

ORDER NO.
PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2006
DV-696AV
DV-696AV-S
RRV3451
DVD PLAYER
DV-696AV-S
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
Model Type Power Requirement Region No. Remarks
DV-696AV-S DXZTRA AC110 to 127 V / 220 to 240 V 1
DV-696AV-S RLFXZT AC110 to 127 V / 220 to 240 V 3
DV-696AV-S RPWXZT AC110 to 127 V / 220 to 240 V 4
DV-696AV-S RTXZT AC110 to 127 V / 220 to 240 V 3
For details, refer to "Important Check Points for Good Servicing" .
T-ZZR AUG. 2006 printed in Japan
DV-696AV-S
2
1234
1234
C
D
F
A
B
E
SAFETY INFORMATION
This service manual is intended for qualified service technicians ; it is not meant for the casual do-
it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been
trainedto properly and safely repair complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and
may void the warranty. If you are not qualified to perform the repair of this product properly and
safely, you should not risk trying to do so and refer the repair to a qualified service technician.
WARNING !
THE AEL (ACCESSIBLE EMISSION LEVEL) OF THE LASER POWER OUTPUT IS LESS THAN CLASS 1
BUT THE LASER COMPONENT IS CAPABLE OF EMITTING RADIATION EXCEEDING THE LIMIT FOR
CLASS 1.
A SPECIALLY INSTRUCTED PERSON SHOULD DO SERVICING OPERATION OF THE APPARATUS.
LASER DIODE CHARACTERISTICS
FOR DVD : MAXIMUM OUTPUT POWER : 5 mW
WAVELENGTH : 650 nm
FOR CD : MAXIMUM OUTPUT POWER : 5 mW
WAVELENGTH : 780 nm
Additional Laser Caution
∗ : See page 55.
726000A140
1. • Laser diode is driving with Q2303,Q2305(650 nm LD) and Q2302,
Q2304(780 nm LD)on the DVD MT PCB Assy.
Therefore, when short-circuit between the emitter and collector of these
transistors or the base voltage is supplied for transistors turn on, the
laser oscillates. (failure mode)
• In the test mode ∗ , there is the mode that the laser oscillates except
for the disc judgment and playback. LD ON mode in the test mode
oscillates with the laser forcibly.
2. When the cover is open, close viewing through the objective lens with
the naked eye will cause exposure to the laser beam.
LABEL CHECK
(Printed on the Rear Panel)
Location: inside of the unit
DV-696AV-S 3
5678
5678
C
D
F
A
B
E
[Important Check Points for Good Servicing]
In this manual, procedures that must be performed during repairs are marked with the below symbol.
Please be sure to confirm and follow these procedures.
1. Product safety
Please conform to product regulations (such as safety and radiation regulations), and maintain a safe servicing environment by
following the safety instructions described in this manual.
1 Use specified parts for repair.
Use genuine parts. Be sure to use important parts for safety.
2 Do not perform modifications without proper instructions.
Please follow the specified safety methods when modification(addition/change of parts) is required due to interferences such as
radio/TV interference and foreign noise.
3 Make sure the soldering of repaired locations is properly performed.
When you solder while repairing, please be sure that there are no cold solder and other debris.
Soldering should be finished with the proper quantity. (Refer to the example)
4 Make sure the screws are tightly fastened.
Please be sure that all screws are fastened, and that there are no loose screws.
5 Make sure each connectors are correctly inserted.
Please be sure that all connectors are inserted, and that there are no imperfect insertion.
6 Make sure the wiring cables are set to their original state.
Please replace the wiring and cables to the original state after repairs.
In addition, be sure that there are no pinched wires, etc.
7 Make sure screws and soldering scraps do not remain inside the product.
Please check that neither solder debris nor screws remain inside the product.
8 There should be no semi-broken wires, scratches, melting, etc. on the coating of the power cord.
Damaged power cords may lead to fire accidents, so please be sure that there are no damages.
If you find a damaged power cord, please exchange it with a suitable one.
9 There should be no spark traces or similar marks on the power plug.
When spark traces or similar marks are found on the power supply plug, please check the connection and advise on secure
connections and suitable usage. Please exchange the power cord if necessary.
0 Safe environment should be secured during servicing.
When you perform repairs, please pay attention to static electricity, furniture, household articles, etc. in order to prevent injuries.
Please pay attention to your surroundings and repair safely.
2. Adjustments
To keep the original performance of the products, optimum adjustments and confirmation of characteristics within specification.
Adjustments should be performed in accordance with the procedures/instructions described in this manual.
4. Cleaning
For parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper
cleaning should be performed to restore their performances.
3. Lubricants, Glues, and Replacement parts
Use grease and adhesives that are equal to the specified substance.
Make sure the proper amount is applied.
5. Shipping mode and Shipping screws
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be
installed before shipment. Please be sure to follow this method especially if it is specified in this manual.
DV-696AV-S
4
1234
1234
C
D
F
A
B
E
CONTENTS
SAFETY INFORMATION..................................................................................................................................... 2
1. SPECIFCATIONS ............................................................................................................................................. 5
2. EXPLODED VIEWS AND PARTS LIST ............................................................................................................ 6
2.1 PACKING SECTION .................................................................................................................................. 6
2.2 EXTERIOR SECTION................................................................................................................................ 8
2.3 06 DVD MECHA SECTION...................................................................................................................... 10
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM..........................................................................................12
3.1 BLOCK DIAGRAM ................................................................................................................................... 12
3.2 OVERALL and POWER BLOCK DIAGRAM ............................................................................................ 14
3.3 OVERALL WIRING CONNECTION DIAGRAM........................................................................................ 16
3.4 DVD MT PCB ASSY (1/7) ........................................................................................................................ 18
3.5 DVD MT PCB ASSY(2/7) ......................................................................................................................... 20
3.6 DVD MT PCB ASSY(3/7) ......................................................................................................................... 22
3.7 DVD MT PCB ASSY(4/7) ......................................................................................................................... 24
3.8 DVD MT PCB ASSY(5/7) ......................................................................................................................... 26
3.9 DVD MT PCB ASSY(6/7) ......................................................................................................................... 28
3.10 DVD MT PCB ASSY(7/7) ....................................................................................................................... 30
3.11 OPERATION, OPERATION 2 and OPERATION 3, 4 PCB ASSYS ....................................................... 32
3.12 POWER PCB ASSY (1/2) ...................................................................................................................... 34
3.13 POWER PCB ASSY (2/2) ...................................................................................................................... 36
3.14 WAVE FORMS....................................................................................................................................... 38
4. PCB CONNECTION DIAGRAM ..................................................................................................................... 41
4.1 LOADING and SW PCB ASSYS.............................................................................................................. 41
4.2 DVD MT PCB ASSY................................................................................................................................. 42
4.3 OPERATION, OPERATION 2 and OPERATION 3, 4 PCB ASSYS ......................................................... 46
4.4 POWER PCB ASSY................................................................................................................................. 50
5. PCB PARTS LIST ........................................................................................................................................... 52
6. ADJUSTMENT ............................................................................................................................................... 53
6.1 WHEN REPLACING DVD DECK ............................................................................................................. 53
6.2 TEST MODE ............................................................................................................................................ 54
6.3 TEST MODE IN........................................................................................................................................ 55
6.4 DISC REMOVAL METHOD...................................................................................................................... 56
7. GENERAL INFORMATION............................................................................................................................. 57
7.1 DIAGNOSIS ............................................................................................................................................. 57
7.1.1 DISPLAY SPECIFICATION OF THE TEST MODE............................................................................ 57
7.1.2 FUNCTIONAL SPECIFICATION OF THE SHORTCUT KEY ............................................................ 58
7.1.3 SPECIFICATION OF MODEL INFORMATION DISPLAY .................................................................. 59
7.1.4 FUNCTIONAL SPECIFICATION OF THE SERVICE MODE ............................................................. 60
7.1.5 METHOD FOR DIAGNOSING DEGRADATION OF THE LDS ON THE PICKUP ASSY .................. 61
7.1.6 TROUBLE SHOOTING...................................................................................................................... 62
7.2 DISASSEMBLY ........................................................................................................................................ 65
7.3 DVD DECK SECTION.............................................................................................................................. 66
7.4 IC INFORMATION.................................................................................................................................... 70
7.5 DISC / CONTENT FORMAT PLAYBACK COMPATIBILITY ..................................................................... 76
8. PANEL FACILITIES ........................................................................................................................................ 78
8.1 FRONT PANEL SECTION ....................................................................................................................... 78
8.2 REMOTE CONTROL ............................................................................................................................... 79
DV-696AV-S 5
5678
5678
C
D
F
A
B
E
1. SPECIFCATIONS
Specifications
General
System . . . . . . . . . . . . . . . . . . . . . . . . DVD player
Power requirements
. . AC 110 V to 127 V / 220 V to 240 V, 50 Hz / 60 Hz
Power consumption . . . . . . . . . . . . . . . . . . . . 8 W
Power consumption (standby) . . . . . . . . . 0.8 W
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.7 kg
Dimensions
. . . . .420 (W) mm x 49.5 (H) mm x 215.5 (D) mm
Operating temperature . . . . . . +5 °C to +35 °C
Operating humidity . . . . . . . . . . . . . . 5 % to 85 %
(no condensation)
Component video output
Y (luminance) - Output level. . . . . . 1 Vp-p (75 Ω)
PB (color) - Output level . . . . . . .
PR (color) - Output level . . . . . . . 0.7 Vp-p (75 Ω)
Jack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RCA
S-video output
Y (luminance) - Output level. . . . . . 1 Vp-p (75 Ω)
C (color) - Output level . . . . . . 286 mVp-p (75 Ω)
Jack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S-video
Video output
Output level . . . . . . . . . . . . . . . . . . . 1 Vp-p (75 Ω)
Jack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RCA
Audio output (1 stereo pair)
Output level . . . . . . . . . . . . . During audio output
200 mVrms (1 kHz, –20 dB)
Number of channels . . . . . . . . . . . . . . . . . . . . . . 2
Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RCA
HDMI output
HDMI output . . . . . . . . . . . . . . . . . . . . . . . . 19 pin
Audio output (multi-channel / L, R, C, SW,
SL, SR)
Output level. . . . . . . . . . . . . During audio output
200 mVrms (1 kHz, –20 dB)
Number of channels . . . . . . . . . . . . . . . . . . . . . 6
Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . RCA jack
Digital audio characteristics
Frequency response . . . . . . . . . . 4 Hz to 44 kHz
(DVD fs: 96 kHz)
4 Hz to 48 kHz (DVD-Audio fs: 192 kHz)
S/N ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 dB
Dynamic range . . . . . . . . . . . . . . . . . . . . . . 100 dB
Total harmonic distortion. . . . . . . . . . . . 0.0025 %
Wow and flutter . . . . . . . .Limit of measurement
(±0.001 % W. PEAK) or lower
Digital output
Coaxial digital output. . . . . . . . . . . . . . . RCA jack
Optical digital output . . . . . . . Optical digital jack
Accessories
Audio/video cable. . . . . . . . . . . . . . . . . . . . . . . . 1
Power cable
Singapore and Taiwan model . . . . . . . . . . . . . 2
Others . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Remote control. . . . . . . . . . . . . . . . . . . . . . . . . . 1
AA/R6P dry cell batteries . . . . . . . . . . . . . . . . . 2
Front panel button names sticker
(Singapore/Taiwan models only) . . . . . . . . . . 1
Remote control overlay
(Singapore/Taiwan models only) . . . . . . . . . . 1
Operating Instructions
The specifications and design of this product are subject to
change without notice, due to improvement.
0.7 Vp-p (75 Ω)
DV-696AV-S
6
1234
1234
C
D
F
A
B
E
2. EXPLODED VIEWS AND PARTS LIST
2.1 PACKING SECTION
Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List.
The mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
Screws adjacent to mark on product are used for disassembly.
For the applying amount of lubricants or glue, follow the instructions in this manual.
(In the case of no amount instructions, apply as you think it appropriate.)
NOTES:
PACKAGE
GIFT SHEET
POLYBAG,INSTRUCTION (RED CAUTION)
PACKAGE
BATTERY,MANGAN
PACKAGE
PACKAGE
POLY BAG INSTA5
TRANSMITTER
CORD,RCA PIN
PACKAGE,PAD
15
14
17
17
3
4
14
13
For DXZTRA, RTXZT type
For RPWXZT, RLFXZT types
2
1
1
5
2
1
14
16
14
12
6
7
8
9
10
18
11
7- 9
"Operating Instructions"
Front
INSTRUCTION BOOK (E/C)
INSTRUCTION BOOK (T)
GUARANTEE CARD
INSTRUCTION BOOK (E)
19
RLFXZT Only
DV-696AV-S 7
5678
5678
C
D
F
A
B
E
PACKING SECTION parts List
(2) CONTRAST TABLE
DV-696AV-S/RLFXZT, /RPWXZT, DV-696AV-S/RTXZT and DV-696AV-S/DXZTRA are constructed the same except
for the following :
Mark No. Description Part No.
>
1 Cord Set AC See Contrast table (2)
2 Cord, RCA Pin 06CPBA2006
3 Remote Control 07650KY010
4 Battery Cover VNK4998
NSP 5 Battery,Mangan (AR, R6P) • • • •
NSP 6 Guarantee Card See Contrast table (2)
7 Instruction Book See Contrast table (2)
8Instruction Book See Contrast table (2)
9 Instruction Book See Contrast table (2)
10 Sheet FP Name See Contrast table (2)
11 Package, Pad 792WHA0604
12 Polyethylene Bag,Instruction See Contrast table (2)
13 Gift Sheet 791WHA0100
14 Package See Contrast table (2)
15 Gift Box See Contrast table (2)
16 Poly, Bag 791WHAA040
17 Carton Label See Contrast table (2)
18 Remote Sheet See Contrast table (2)
NSP 19 Label Safefy See Contrast table (2)
Mark No. Description Part No.
Mark No. Symbol and Description DV-696AV-S/
DXZTRA DV-696AV-S/
RLFXZT DV-696AV-S/
RPWXZT DV-696AV-S/
RTXZT
>
1 Cord Set AC 1209198901 120S198902 120G168801 1206158802
>
1 Cord Set AC Not used 1206158802 Not used Not used
NSP 6 Guarantee Card J2I83002A Not used Not used J2I81292A
7 Instruction Book (English) J2J00901A Not used J2J00901A Not used
8 Instruction Book (English, Chinese) Not used J2J00910B Not used Not used
9 Instruction Book (Thai) Not used Not used Not used J2J01001A
10 Sheet FP Name Not used 723000D345 Not used Not used
12 Polyethylene Bag,Instruction JB5UD200 JB5UD200 JB5UD100 JB5UD100
14 Package 792WHAA190 792WHAA190 792WHAA191 792WHAA190
15 Gift Box 793WCDD221 793WCDD221 793WCDD246 793WCDD221
17 Carton Label 723000D381 Not used Not used 723000D377
18 Remote Sheet Not used 7230007993 Not used Not used
NSP 19 Label Safety Not used Not used Not used 723000D372
DV-696AV-S
8
1234
1234
C
D
F
A
B
E
2.2 EXTERIOR SECTION
PCB240
(POWER PCB ASS'Y)
29
30
A
A
C
C
B
B
15
31
9
10
6
E
E
CONTACT SIDE
NON-CONTACT
SIDE
A
B
C
G
H
F
20
20
20
20
20
1
19
21
21
21
13
13
8
19
4
5
14
19 19
2
27
3
17
19
31 19
19
101C 22
22
22
22
26
22
22
22
11
13
13
16
19
18
18
18
18
23
24
25
(OPERATION 3 PCB ASS'Y)
PCB280
(OPERATION 2 PCB ASS'Y)
PCB270
(OPERATION 1 PCB ASS'Y)
PCB130
(DVD PCB ASS'Y)
101
101A
101E
101M
101G
101I
101D
101N
101J
101B
101K
101L
101F 101H
PCBDF0
12
12
16
PCBDG0
(OPERATION 4 PCB ASS'Y)
22
22
101O
101P
30
29
Refer to
"2.3 06 DVD MECHA SECTION".
" FRONT PANEL SECTION".
32
28
7
DV-696AV-S 9
5678
5678
C
D
F
A
B
E
EXTERIOR SECTION parts List
(2) CONTRAST TABLE
DV-696AV-S/RLFXZT, /RPWXZT, DV-696AV-S/RTXZT and DV-696AV-S/DXZTRA are constructed the same except
for the following :
Mark No. Description Part No.
1DVD MT PCB Assy See Contrast table (2)
2 OPERATION PCB Assy See Contrast table (2)
3 OPERATION 2 PCB Assy A2I802A280
>
4POWER PCB Assy A2J012A240
5DVD MECHA ASSY A2I802A650
6 Cord Jumper(CD604) 122H051706
NSP 7 Energy Star Label See Contrast table (2)
NSP 8 Plate,Bottom 702WSA0291
9 Cord Jumper(CD601) 122H0B1003
10 Cord Jumper(CD602) 122H091303
11 Plate,Cover power 755WPAA031
12 Holder,FFC 761WPA0396
13 Cushion,Leg VEB1349
14 Cabinet,Top 702WSB0114
NSP 15 Sheet, Fuse 7240001122
16 Cushion (15x20x16) 8965TS101B
17 OPERATION 4 PCB Assy A2I903ADG0
18 Screw,Tap Tite(S)-Bind Wash. 816423063U
19 Screw,Tap Tite(S) (3x5.5) 8107D3055U
20 Screw,Tap Tite(B) (3x6.0) 8109K3060U
21 Screw,Tap Tite(B)Pan (3x6) 810913060U
22 Screw,Tap Tite(P) (2.6x8) 811022680U
See Contrast table (2)
NSP 25 Sheet,Jack 3 See Contrast table (2)
NSP 26 Double,Face-Tape 7290000156
27 OPERATION 3 PCB Assy A2I903ADF0
NSP 28 Sheet Caution See Contrast table (2)
29 Spring Earth 743WKAA015
30 Screw PAN 810213060U
31 Cord Connector (CD502) 06CU2E3301
NSP 32 Sheet Caution See Contrast table (2)
101 Front Cabi Assy 7A701A754A
NSP 101A Cabinet, Front 701WPQA005
NSP 101B Plate, Display 711WPA0253
NSP 101C Plate, Cover
101D Flap, DVD
NSP 101E Badge,Brand 7236310014
NSP 101F Button,Frame 1 735WPA0874
NSP 101G Button,Frame 4 735WPA0879
NSP 101H Button,Frame 2 735WPB0328
NSP 101I Button,Frame 5 735WPB0329
NSP 101J Button,Frame 3 735WPB0330
NSP 101K Button, Cap 735WPE0043
NSP 101L Button, Cap 2 735WPE0044
NSP 101M Button, Cap 1 735WPN0001
101N Spring,Flap-DVD 743WKA0052
101O SHEET DVD 7236740001
NSP 101P Glass LED 713WPA0385
Mark No. Description Part No.
Mark No. Symbol and Description DV-696AV-S/
DXZTRA DV-696AV-S/
RLFXZT DV-696AV-S/
RPWXZT DV-696AV-S/
RTXZT
1DVD MT PCB Assy A2J009A130 A2J009A130 A2J012A130 A2J012A130
NSP 2 OPERATION PCB Assy A2I813A270 A2I813A270 A2I813A270 A2I812A270
7 Energy Star Label Not used Not used 7230007965 Not used
NSP 24 Sheet, Jack 2 722631A146 722631A143 722631A146 722631A121
NSP 25 Sheet, Jack 3 722631A158 722631A144 722631A147 722631A122
NSP 28 Sheet, Caution 726000A140 726000A142 726000A140 726000A140
NSP 32 Sheet, Caution 725000A089 Not used 725000A089 Not used
DV-696AV-S
10
1234
1234
C
D
F
A
B
E
2.3 06 DVD MECHA SECTION
Applying positions AA, AB and AC for the
grease are displayed for this section.
Check if the correct grease is applied for each
position.
NOTE:
CLASS MARK
GREASE G-555G AA
G-313Y AB
PART NO.
GEM1018
PART NAME
GYA1001
FL-78A AC
GEM1036
Cannot supply separately.
If the repair is needed, replace the
LOADER SUB ASS'Y.
PCB610
(LOADING MOTOR PCB ASS'Y)
CD2302
Do not replace the parts. Because,
minute adjustments are needed if
this condition is disassembled
further more.
If the repair is needed, replace the
DVD MECHA ASS'Y.
(SW PCB ASS'Y)
10
AB
AB
AB
AA
Pickup leneses
GEM1004
GED-008
Grease
GEM1018
34
15
14
21
18
11
23
9
AB
19
1
29
AB
AB
3
12
20
6
4
SW1
31
PCB640
27
22
22
16
2
CD2001
24
5
25
26
32
8
13 8
30
SW2
33 CD2301
AC
AC
AB
D
E
Lubricating Oil
GYA1001
Grease
GEM1036
Note :
Lubricating Oil
GYA1001
7
17
28
DV-696AV-S 11
5678
5678
C
D
F
A
B
E
06 DVD MECHA SECTION parts List
Mark No. Description Part No.
NSP 1 Loading Motor PCB Assy A2F101A610
2 Gear,Middle 92P100117A
3 Loading Motor 1515S98004
4 Pulley,Motor 92P100097A
5 FEED Motor 1515S98004
6 Cord Jumper (24P)(CD2001) 122J402202
7 Cord Jumper (CD2302) 122H051602
8 Insulator (F) 92P200013A
9 Belt,Loading 92P200015A
10 Insulator (R) 92P200016A
11 Frame,main 92P100119A
12 Tray (B) 92P100127B
13 Holder ,Traverse 92P100125A
14 Gear,Pulley 92P100123A
15 Gear,Main 92P100124A
16 Gear,Feed 92P100116A
NSP 17 SW PCB Assy (PCB640) A2F101A640
18 Plate, Clamper 92P000023A
19 LOADER SUB ASSY (B) 92AAA0019B
20 Clamper 92P100122A
21 Screw,Pan (M1.7x3 P3) 814011730U
22 Screw,Pan (M1.7x2.3 P3) 814011723U
23 Rack,Loading 92P100121A
24 Gear,Motor 92P100088A
25 Feed Rack Assy 92AAA0017A
26 Screw,T-Tite(B) (M1.7x5.0 P3) 813381750U
27 Screw,Gear Feed 92P700007A
28 Cord Jumper (CD2301) 122H061605
29 Switch (SW1) 0515S32003
30 Push Switch (SW2) 0500101036
31 Screw,Tap Tite(P) (2.6x8) 811022680U
32 Sems.Tap Tite(P) (2x8) 816112080U
33 Screw,Tap Tite(P) BI 811022080U
34 DVD MECHA ASSY A2I802A650
DV-696AV-S
12
1234
1234
C
D
F
A
B
E
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM
3.1 BLOCK DIAGRAM
D2+
1
3
D1+
4
D1-
6
D0+
7
D0-
9
CLK+
10
D2-
HDMI CONNECTOR
CP5901
DVD
Loader
(DM-4)
MPEG/MICON IC
IC4002
MT1389EXE/B2-L
X4001
27MHz
IOA, V20
C
RF, A, B, C, D, E, F, MDI1
LD_DVD, LD_CD Q2302~2305
LD DRIVE
LDO1, LDO2
MOTOR DRIVER IC
IC2301
LA6565VR-TLM-E
DMSO, FMSO,
TROPEN, TRCLOSE,
TRSO, FOSO,
STBY, V1P4
T+/-, F+/-,
LOAD+/-,
MOT_SLED+/-,
MOT_SPDL+/-
OPU
SPINDLE/
STEPING/
SLED
MOTOR
LIMIT, TRIN, TROUT,
16Mbit FLASH
IC4004
S29AL016D70TFI020
MA0~MA11, DQ0~DQ15,
DQM0, DQM1, DBA0, DBA1,
SDCLK, SDCKE, DWE#,
DRAS#, DCAS#, DCS#
A
D
A0~A20, AD0~AD7,
PRD#, PCE#, PWR#
64Mbit SDRAM
IC4005
EM638165TS-7G A
A
SDA
16
CLK-
12
HOTPLUG
19
POWER
18
15 SCL
HDMI TRANSMITTER IC
IC5901
MT1392E/C-L
SCL
SDA
92_Y0~Y7
92_VCK, 92_ACLK, XO
ASPDIF
EEPROM IC
IC4001
BR24L08FJ-WE2 SCL
A
SDA
HDMI_SCL
HDMI_SDA
H
A, B
RESET IC
IC4003
BD5229G-TR
A
RESET
DVD LOADER/MPEG BLOCK DIAGRAM
DV-696AV-S 13
5678
5678
C
D
F
A
B
E
O
N IC
/
B2-L
4
3Y
C
S-VIDEO JACK
J7301
A.......AT+3.3V
B.......+1.8V
C.......P.CON+5V
D.......P.CON+6V
E.......AT+12V
F.......P.CON+12V
G.......-28V
H.......V+5H
L
D
A
R
ESET IC
IC4003
D
5229G-TR
RESET
IR
IR RECEIVER (OS651)
ROM-N340TAO
IR A
GR1~GR8, P1~P16
FP_DI, FP_DO,
FP_SCK, STB FIP DRIVER IC
IC651
PT6315
A
FIP (V651)
HNV-08SS44T
G
A, B
3
5Y
U
VIDEO JACK
J7302
2V
VIDEO DRIVER 6CH IC
IC7301
LA73054-TLM-E
LETTER, SQUEEZE, VSEL1,
I/XP, R/CR, B/CB, G/Y, C/V,
S_C, S_Y
C
6CVBS
IC8003/4/5
AUDIO DAC IC
PCM1742KEG/2K
DAC_XCSO, SCK, SD,ACLK,
ABCK, ALRCK, ASDAT0~2
1
COAXIAL JACK
J8102
COAXIAL
ASPDIF
1
OPTICAL
OS8001
OPTICAL
5
3SL
C
LS/RS/S/LFE JACK
J8002
6LFE
2SR
A, C
IC8006/7/8
AUDIO LPF AND AMP IC
RC4580IDR
G
L/R JACK
J8001
3
2R
L
DV-696AV-S
14
1234
1234
C
D
F
A
B
E
3.2 OVERALL and POWER BLOCK DIAGRAM
P.CON+12V
AC220 V
- 240 V
AC110 V
- 120 V V+5V
27MHz
-28V
AT+12V for mute
AT+3.3V
P.CON+6V
P.CON+5V
POWER
SUPPLY
DVD LOADER
(DM4)
MOTOR DRIVER
IC2301
LA6565VR-TLM-E
FIP DRIVER IC
IC651
PT6315
8K EEPROM
IC4001
BR24L08FJ-WE2
FIP
HNV-08SS44T
KEY
SERVO
RF
SERVO
IR
FP,STB
ASPDIF
RESET
LD_DVD,
LD_CD
IR 108MHz
TV Encoder
MPEG-1/2/
JPEG
VIDEO
DECORDER
RF
IR RECEIVER (OS651)
ROM-N340TAO
16Mbit FLASH
IC4004
S29AL016D70TFI020
64Mbit SDRAM
IC4005
EM638165TS-7G
SDA, SCL
AMUTE
MPEG/MICON BLOCK
IC4002
MT1389EXE/B2-L AUDIO CODEC/
INTERNAL DAC
+1.8V
A0~A20,
AD0~AD7 MA0~MA11,
DQ0~DQ15
RESET IC
IC4003
BD5229G-TR
VIDEO DRIVER 6CH IC
IC7301
LA73054-TLM-E
6CH VIDEO DAC
V
CVBS
U
Y
HDMI TRANSMITTER IC
IC5901
MT1392E/C-L
HDMI
CONNECTOR
CP5901
92_Y0~Y7,
92_VCK,
92_ACLK
TX0+/-,
TX1+/-,
TX2+/-,
TXC+/-
S_VIDEO S
CO
COAXIAL
OPTICAL OP
IC8003/4/5
AUDIO DAC IC
PCM1742KEG/2K
DAC_XCSO, SCK, SD,
ACLK, ABCK, ALRCK,
ASDAT0~2
IC8006/7/8
AUDIO LPF AND AMP IC
RC4580IDR
C
LFE
SR
L
R
FLDC+/-
SL
• OVERALL BLOCK DIAGRAM
DV-696AV-S 15
5678
5678
C
D
F
A
B
E
SWITCHING
TRANS
T501
P.CON SW
• POWER BLOCK DIAGRAM
Q505
AC IN
P.CON+5V
AT+3.3V
FL DC -
-28V
AT+12V for mute
P.CON+6V
P.CON+12V
P.ON-H
FL DC +
Q515
P.CON +5V SW
Q510
P.CON +12V SW
Q504
FL+ P.CON SW
Q502
-28V P.CON SW
VOLTAGE CTL
IC501
KIA431A-AT
PHOTO COUPLER
IC504
PS2561AL1-1-V (W)
POWER CTL
IC502
STR-A6131M
6V REG
IC503
PQ070XF01SZH
REG+1.8V
IC4006
LM1117S-ADJ +1.8V
HDMI+5V REG IC
IC5902
PQ1K503M2ZPH V+5H
DV-696AV-S
16
1234
1234
C
D
F
A
B
E
3.3 OVERALL WIRING CONNECTION DIAGRAM
9
8
7
6
4
5
3
2
1
CP603
9
8
7
6
4
5
3
2
1
CP602
11
10
9
8
7
6
5
4
3
2
1
11
10
9
8
7
6
5
4
3
2
1
14
13
12
11
10
9
8
7
6
4
5
3
2
1
CP502
14
13
12
11
10
9
8
7
6
4
5
3
2
1
CP4003
5
4
3
2
1
CP605
5
4
3
2
1
CP604
Vout
B+
GND
OS651
1
2
3
21
AC110 - 127 V_50 Hz/60 Hz
AC220 - 240V_50Hz
CD501_2
AC INLET
J501
1 2
BLACK
WHITE
L
N
NN
L
(CD502)
14
13
14
13
12
11
10
9
8
7
6
5
4
3
2
1
12
11
10
9
8
7
6
5
4
3
2
1
(CD604)
5
6
7
8
9
5
4
3
2
1
LED
V+3E
GND(NC)
POWER
SW2
(CD602)
5
6
7
8
9
5
4
3
2
1
LED
V+3E
GND(NC)
POWER
SW2
PAUSE/-SKIP
PLAY/+SKIP
V+3E
SW2
LED
GND
STOP
POWER
SW1
PAUSE/-SKIP
PLAY/+SKIP
V+3E
SW2
LED
GND
STOP
POWER
SW1
9
8
7
4
2
1
3
6
FLDC-
FLDC+
V+3E
-28V
DGND
DGND
DO (F to M)
DI (M to F)
IR
STB
CLK
DGND
DGND
FLDC+
-28V
FLDC-
DI (M to F)
V+3E
STB
DO (F to M)
IR
CLK
AT+3.3VAT+3.3V
AT+3.3V
(CD601)
11
10
9
8
7
6
5
4
3
2
1
11
10
9
8
7
6
5
4
3
2
1
CP601 CP4002
P.CON+12V
P.CON+5V
FL DC-
FL DC+
GND
GND
AT+12V for MUTE
P.ON-H
P.CON+6V
-28V
GND(M)
GND(D)
GND
P.CON+5V
FL DC-
FL DC+
-28V
AT+3.3V
GND
P.CON+12V
AT+12V for MUTE
P.CON+6V
GND(M)
GND(D)
P.ON-H
D660
LTL-1CHEE-002A
HDMI LED(RED)
R664
330 1/4W
W808W807
OPERATION 4 PCB ASSY
(A2I903ADG0)
H
Vout
B+
GND
OS8101
1
2
3
H
E
J8102
COAXIAL
1
2
2
1
2
1
2
1
CP8102
2
1
CP8001
SPDIF
GND
SPDIF
GND
OPERATION PCB ASSY
(/DXZTRA, /RLFXZT,
/RPWXZT : A2I813A270)
(/RTXZT : A2I812A270)
B
OPERATION 2
PCB ASSY
(A2I802A280)
C
G
POWER PCB ASSY (A2J012A240)
F1/2, F2/2
F
: POWER BLOCK
F1/2
: AUDIO BLOCK
F2/2
AC IN
OPERATION 3 PCB ASSY
(A2I903ADF0)
DV-696AV-S 17
5678
5678
C
D
F
A
B
E
19
18
17
16
15
14
13
12
11
10
9
8
7
6
4
5
3
2
1
CP5901
HDMI CONNECTOR
H1H2
E
H1H2
E
J8002
LS/RS/C/U/LEF
1
23
4
56
H1H2
E
J8001
AUDIO OUT L/R
1
23
D2+
D2-S
D2-
D1+
D1-S
D0+
D0-S
D0-
CLK-S
CLK-
CEC
SCL
SDA
GND
POWER
HOTPLUG
NC
D1-
CLK+
LOADING MOTOR
SLED MOTOR
SPINDLE MOTOR
GND(SW)
SW-2(CLOSE)
SW-1(OPEN)
M2601
M
M
M
M2602
SW2
CD2301
CD2302
DVD MECHA ASSY
(A2I802A650)
D E
BCZ3B05
JCV9B12
ESE22MH22
BCZ3B05
M2603
SSS-28-5
SW1
5
4
3
2
1
CP2302
6
5
4
3
2
1
CP2303
24
23
22
21
20
19
2
1
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
CP2301
DM-4PB
LD- LD-
LD+LD+
OPEN
GND(D)
CLOSE
SW(GND)
SLD-
SLD+
SP1-
SP1+
LIMIT SW
SW(GND)
SLD-
SLD+
SP1-
SP1+
LIMIT SW
GND
VS
VCC
E
D
C
SW1(DVD/CD)
VRF(RF_OUT)
B
A
VR COM
VR(CD)
LD(CD)
LD(DVD)
GND
NC
T DRV
T RTN
F DRV
F RTN
F
VR(DVD)
GND
PD/GND
GND
VS
VCC
E
D
C
SW1(DVD/CD)
VRF(RF_OUT)
B
A
VR COM
VR(CD)
LD(CD)
LD(DVD)
GND
NC
T DRV
T RTN
F DRV
F RTN
F
VR(DVD)
GND
PD/GND
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
6
5
4
3
2
1
6
5
4
3
2
1
DRIVE
DVD
OPTICAL PICK-UP
LOADING MOTOR
PCB ASSY
(A2F101A610)
E
SW PCB ASSY
(A2F101A640)
D
J7301
S-VIDEO OUT
12
34
56
H1H2
E
H1H2
E
J7302
CVBS/Y/U/V
1
23
4
56
DVD MT PCB ASSY
(/DXZTRA, /RLFXZT : A2J009A130)
(/RPWXZT, /RTXZT : A2J012A130)
A1/7- A7/7
A
: MPEG/MICON/RF-AMP BLOCK
A1/7
: LOADER/MOTOR DRIVE BLOCK
A3/7
: MEMORY BLOCK
A2/7
: AUDIO JACK BLOCK
A4/7
: HDMI BLOCK
A6/7
: VIDEO JACK BLOCK
A5/7
: POWER PORT BLOCK
A7/7
VIDEO OUT AUDIO OUT
AUDIO OUT (5.1 ch)
S-VIDEO OUT
÷When ordering service parts, be sure to refer to "EXPLODED VIEWS and PARTS LIST" or
"PCB PARTS LIST".
÷The > mark found on some component parts indicates the importance of the safety factor
of the part. Therefore, when replacing, be sure to use parts of identical designation.
÷: The power supply is shown with the marked box.
DV-696AV-S
18
1234
1234
C
D
F
A
B
E
3.4 DVD MT PCB ASSY (1/7)
IC4002
MT1389EXE/B2-L
MPEG/MICON
222223224225226227228229230231232233234235236237238239240
241242243244245246247248249
250251
252
253254
255256
110111213141516171819 22021222324
2526272829 3
30313233343536373839 4
40414243444546474849 5
50
51525354
55
56575859 6
6061626364
65 66 67 68 69
7
70 71 72 73 74 75 76 77 78 79
8
80 81 82 83 84 85 86 87 88 89
9
90 91 92 93 94 95 96 97 98 99
R4008
10K
R4003
10K
R4005
680K
R4020 15K
R4027
100
R4035 33
R4014 10K
R4004 10K
R4006
10K
R4015 10K
R4016 15K
R4017 22K
R4018 12K
R4019 12K
R4002 10K
R4022
100K
R4030 10
R4024
750K
R4025
100K
TP4107
TP4009
TP4007
TP4001
TP4002
TP4003
TP4004
TP4005
TP4006
TP4008
TP4015
TP4016
TP4017
TP4018
TP4019
TP4020
TP4021
TP4030
TP4031
TP4032
TP4022
TP4023
TP4024
TP4025
TP4026
TP4027
TP4028
TP4029
TP4108
TP4109
TP4012
TP4013
TP4010
TP4011
TP4103
TP4014
TP4034
TP4033
TP4035
W881
C4026
0.1 B
C4012
0.1 B
C4105
0.0022 B
C4009
0.015 B
C4008
0.1 B
C4007
0.1 B
C4020
0.1 B
C4037
1B
C4032 0.1 B
C4031 0.033 B
C4027 0.1 B
C4028 0.1 B
C4029 0.1 B
C4043
0.1 B
C4041
0.1 B
C4036
0.1 B
C4039
0.1 B
C4048
7P CH
C4050
0.1 B
C4013 0.1 B
C4014 1 B
C4015 1 B
C4016 1 B
C4001 0.0022 B
C4002 470P CH
C4022
0.1 B
C4003 470P CH
C4021 0.1 B
C4017 1 B
C4103 1 B
C4005
0.1 B C4019 0.1 B
C4030
0.1 B
C4025
0.1 B
C4024 0.0015 B
C4051
0.1 B
C4042
0.047 B
C4044
0.047 B
C4040
1B
C4033
0.001 B
C4049
7P CH
C4045 0.47 B
C4034
22P CH
C4035
0.1 B
C4047
390P CH
IC4001 BR24L08FJ-WE2
EEPROM
1234
5678
C4023
2206.3V YK
C4046 1025V KA
X4001
100GT02720
27MHz
B4010
MMZ1608R102CT
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
XO
V+3
ASPDIF
PWDN#
V1P4
A
B
C
D
E
F
MDI1
LDO1
LDO2
V1P4
DMSO
FMSO
TRCLOSE
TROPEN
TRSO
FOSO
OPO
OP+
OP-
TROUT
TRIN D
STBY A
V20 B
LIMIT C
IOA
RF RF
D_GND
E
F
MDI1
LDO2
LDO1
MA0
MA1
MA2 V20
MA3 V1P4
MA4
MA5
MA6
MA7
MA8
MA9
MA10 OPO
MA11 OP-
SDCKE
SDCLK OP+
DBA0 DMSO
DBA1 FMSO
DCS# TROPEN
DRAS#
DCAS#
DWE# TRSO
DQM0 FOSO
DQM1
DQ0 V1P4
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6 TROUT
DQ7 TRIN
DQ8 STBY
DQ9 TRCLOSE
DQ10
DQ11
DQ12 A2
DQ13 A3
DQ14 A4
DQ15
A0 A5
A1 A6
A2 A7
A3 A8
A4
A5 A18
A6 A19
A7
A8
A9 SDA
A10 SCL
A11 V+3
A12
A13
A14
A15
UWR#
URD#
A16
A17
A18
A19
A20
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
PWR#
A16
A15
A14
A13
A12
A11
A10
A20
PCE#
PRD#
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
A17
A9
A1
A0
PWR#
PCE#
PRD#
D_GND
FP_SCK
FP_DI
FROM/TO LOADER/MOTOR DRIVE
3.3
0.0
3.3
3.3
3.3V
1.8V
VCC
WP
SCL
SDA
NC
NC
NC
GND
(V+3D)
ADIN
IOCE#
IOWR#
3.3
NC
NC
NC
NC
NC
NC
NC
NC
NC
0.0
1.2
2.1
0.9
0.8
1.6
0.0
2.1
2.1
2.1
2.1
0.0
0.0
0.0
0.0
0.0
2.0
2.1
2.5
0.0
0.0
3.3
3.3
2.3
2.1
0.0
2.8
2.0
1.4
1.3
1.3
1.3
2.5
1.7
1.5
2.0
1.3
0.0
1.4
1.4
1.5
0.0
0.0
0.0
2.5
3.3
0.0
3.3
0.0
1.8
2.2
2.1
1.9
2.2
2.0
2.0
1.9
0.2
0.0
1.6
0.0
0.0
0.0
3.33.33.33.33.33.33.33.33.33.33.33.33.33.33.33.33.33.33.33.33.33.33.33.33.33.33.33.33.33.33.33.33.33.33.33.33.33.33.33.33.33.33.33.33.33.33.33.33.33.33.33.33.33.33.33.33.33.33.33.33.33.33.33.33.3
2.9
1.0
2.5
1.2
1.4
1.4
3.3
1.2
1.0
3.3
0.0
0.0
2.1
0.0
3.3
1.3
1.4
1.3
0.0
0.0
1.6
1.7
1.7
0.0
0.0
1.7
0.0
1.9
0.0
3.3
3.3
1.8
3.2
2.8 1.2
0.0
3.3
1.7
0.0
1.8
0.7
1.0
1.1
1.1
0.0
0.0
3.3
1.8
1.6
1.6
1.4
3.3
0.0
0.0
0.0
0.0
3.3
1.4
1.4
2.0
0.0
0.0
0.0
0.0
1.5
1.2
1.0
3.3
1.5
0.0
0.0
0.0
0.0
AGND
DVDA
DVDB
DVDC
DVDRF[P
DVDRF[N
MA
MB
MC
DVDD
SB
SC
SD
CDFON
CDFOP
TNI
SVDD3
SGND
V2REFO
V20
VFEFO
FEO
TEO
PWMOUT1/V_ADIN9
USBM
USB_VDD3
TDI/V_ADIN4 (JTAG)
FG/V_ADIN8 (PU)
TCK/V_ADIN6 (JTAG)
TDO/V_ADIN7 (JTAG)
IOA19 (PU)
IOA18 (PU)
65
66
67
68
254
253
255
256
A16
HIGHA7 (PU)
DVDD3
HIGHA2 (PU)
HIGHA3 (PU)
HIGHA4 (PU)
HIGHA5 (PU)
HIGHA6 (PU)
HIGHA1 (PU)
IOA20
XIOCS (PU)
DVDD3
AD0
AD1
AD2
AD3
DVSS (18)
AD4
AD5
AD6
ALE (PU)
AD7
A17
IOA0 (PU)
DVSS (3)
XUWR (PU)
XURD (PU)
DVDD18
UP1_2 (PU)
UP1_3 (PU)
MC_DATA (PD)
XTALI
JITFO
JITFN
RFRPDC
RFRPAC
HRFZC
CRTPLP
RFGND
CEQN
OSP
OSN
IREF
AVDD3
CSO/RFOP
TROPENPWM
TMS/V_ADIN5 (JTAG)
RFGC
SA
MD
TPI
LDO2
LDO1
OP_OUT
OP_INN
OP_INP
DMO
FMO
TRO
USBP
USB_VSS
DVDD18
IOA2 (PU)
IOA3 (PU)
IOA4 (PU)
IOA5 (PU)
IOA6 (PU)
HIGHA0 (PU)
APLLCAP
APLLVSS
DVSS
(PD) ASDATA4
(3) DVSS
SPDIF
RFGND18
RFVDD18
XTALO
PLLVSS
IDACEXLP
PLLVDD3
LPFON
LPFIP
LPFIN
LPFOP
ADCVDD3
S_VCM
ADCVSS
S_VREFP
S_VREFN
RFVDD3
CEQP
V+3RF
RFLV
FE
TE
FROM/TO MEMORY
FOO
MDI1
MDI2
RFLVL/RFON
TEZISLV
IOA7 (PU)
APLLVDD3
XIOWR
IOA1 (PU)
XIOOE
IOA21/V_ADIN0
CS
(RF)
(D)
(A)
(B)
(C)
(E)
(F)
(D)
(A)
(B)
(C)
(E)
(RF) (RF)
(F)
1
EEPROM
3
7
8
A1/7
2/7A3/7A
DVD MT PCB ASSY
(/DXZTRA, /RLFXZT : A2J009A130)(/RPWXZT, /RTXZT : A2J012A130)
A1/7
MPEG / MICON / RF-AMP BLOCK
DV-696AV-S 19
5678
5678
C
D
F
A
B
E
101102103104105106107108109110111112113114115116117118119120121122123124125126127128
129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189190191192
193194195196197198199200201202203204205206207208209210211212213214215216217218219220221
100 R4007
100
R4052
10K
R4038 33
R4040 33
R4043 33
R4050 33
R4047 33
R4046 10
R4083 100
R4070 33
R4071 33
R405410K
R4061
2.7K +-1%
R4062 15K
R4060
33
R4082 33
R4032 33
R4051 33
R4048 10K
R4053 10K
R4057 10K
R4084
1K
R4064 150+-1%
R4068 150+-1%
R4067 150+-1%
R4066 150+-1%
R4065 150+-1%
R4069 150+-1%
TP4053
TP4054
TP4055
TP4056
TP4057
TP4058
TP4059
TP4051
TP4052
TP4048
TP4106
TP4044 TP4043
TP4041
TP4039
TP4036
TP4037
TP4038
TP4063
TP4045
TP4076
TP4077
TP4078
TP4079
TP4080
TP4081
TP4082
TP4086
TP4087
TP4088
TP4085
TP4084
TP4083
TP4070
TP4071
TP4072
TP4075
TP4069
TP4073
TP4074
TP4110
TP4100
TP4101
TP4102
TP4095
TP4096
TP4097
TP4099
TP4098
TP4094
TP4060
TP4062
TP4061
TP4067
TP4066
TP4068
TP4046
TP4047
TP4050
TP4049
TP4089
TP4065
TP4040
TP4104
TP4042
TP4105
W805 W806
W846
W804
C4104
0.0082 B
C4053
0.1 B
C4114
1B
C4055
0.1 B
C4073
0.1 B
C4072
0.1 B
C4068
0.1 B
C4062
0.1 B
C4064
0.1 B
C4069
100P CH
C4061
0.1 B
C4060
0.1 B
C4063
0.1 B
C4066
1B
C4054
220P CH
C4076 33P CH
C4077 100P CH
C4078 33P CH
C4067
0.1 B
C4091
0.1 B
C4071
0.1 B C4110
100P CH
C4117
100PCH
C4079 100P CH
IC4003 BD5229G-TR
RESET IC
123
45
CP4002
00_6232_011_006_800+
1
10
11
2
3
4
5
6
7
8
9
NR4002
4D03WGJ0330T5E
NR4001
4D03WGJ0330T5E
NR4005
4D03WGJ0220T5E
NR4006
4D03WGJ0220T5E
DURING PLAYBACK.
MEASURED WITH THE DIGITAL TESTER
NOTE:THE DC VOLTAGE EACH PART WAS
IOA
SCK
ACLK
ABCK
G/Y
S_C
S_Y
ALRCK
XMMUTE
XAMUTE
HSYNC
VSYNC
R/CR
B/CB
V+3A
CVBS
ASDAT2
ASDAT1
ASDAT0
VSEL1
LETTER
SQUEEZE
I/XP
V+3V R/CR
B/CB
G/Y
SD CVBS
S_C
DAC_XCS0 S_Y
D_GND
SD
SCK
DAC_XCS0
XAMUTE
XMMUTE
VSEL1 ALRCK
ABCK
ACLK
LETTER ASDAT0
SQUEEZE ASDAT1
I/XP ASDAT2
ASPDIF
D_GND
92_VCK
92_Y0
92_Y1
92_Y2
92_Y3
92_Y0
92_Y1
92_Y2
92_Y4 92_Y3
92_Y5 92_Y4
92_Y6 92_Y5
92_Y7 92_Y6
92_Y7
92_VCK
MA4 HDMI_SCL
MA5 HDMI_SDA
MA6 XO
URST#
MA7 HSYNC
VSYNC
MA8
MA9
MA11
SDCKE PWDN#
SDCLK V+1R8
V+3
V+3E
V+3A
FLDC-
FLDC+
MA3 -28V
MA2 D_GND
MA1
MA0
MA10 V+3
DBA1 RXD
DBA0 TXD
D_GND
DCS#
DRAS#
DCAS#
DWE#
DQS1 LIMIT
DQM1
DQ8
DQ9 FP_SCK
DQ10 FP_DI
DQ11 STB
DQ12
DQ13 FP_DO
IR
V+3E
FLDC+
-28V
FLDC-
DQ15
DQ14
DQM0
DQ7
DQ6
DQ5
DQ4
DQ3
DQ2
DQ1
DQ0
RESET
HDMI_SCL
HDMI_SDA
V+1R8
FP_DO
V+3
STB
SCL
SDA
RXD
TXD
IR
TO HDMI
FROM/TO POWER PORT
TO AUDIO/JACK
TO VIDEO
0
0
NC
NC
NC
NC
2.7
3.0
3.3
3.3
3.3
0.0
3.3
3.3
3.3
3.3
3.3
1.0
3.3
1.9
0.0
1.2
0.0
1.1
1.2
0.0
1.4
1.4
1.8
1.0
1.3
0.0
1.5
3.3
1.4
3.3
1.1
1.6
1.4
1.4
0.0
1.3
3.3
1.9
2.6
3.1
2.7
3.1
3.3
1.7
0.0
1.6
0.0
0.7
0.0
2.0
2.0
1.9
1.8
0.0
0.0
3.3
1.8
2.0
0.0
0.0
0.0
0.0
1.5
0.0
1.6
1.4
1.6
3.3
3.3
0.0
3.3
0.0
0.0
1.8
0.0
0.0
0.0
3.3
3.3
3.3
0.0
0.0
3.3
0.0
0.0
0.0
0.0
0.0
0.0
1.4
1.4
2.3
1.3
NC
NC
0.0
1.0
3.3
1.0
0.0
1.0
3.3
0.0
0.0
0.0
0.0
3.3
0.0
3.3
3.3
3.3
3.3
0.0
0.0
3.3
1.7
1.7
1.6
0.0
1.3
0.0
0.0
1.8
UP1_4 (PU)
UP1_5 (PU)
UP1_6 (PU)
UP1_7 (PU)
UP3_0 (PU)
UP3_1 (PU)
UP3_4 (PU)
PU3_5 (PU)
DVDD3
ICE (PD)
IR
DQM0
DQS0
RD7
DVSS (18)
RD6
125
126
127
128
RD5
DVSS (3)
RD4
RD3
DVDD18
RD2
RD1
RD0
RD15
RD14
RD13
RD12
RD11
RD10
RD9
(3) DVSS
DQS1
RD8
DQM1
XCAS
XRAS
DVDD3
XRCS
BA0
(18) DVSS
BA1
RA10
RA0
(3) DVSS
RA1
RA2
RA3
DVDD18
RCLKB
DVDD3
RCLK
RA11
RA9
RA8
(3)DVSS
RA7
(18) DVSS
RA6
RA5
RA4
DVDD3
(PU) RD30
RD29
RD28
RD27
DVDD18
RD26
(3) DVSS
RD25
RD24
(PD) DQM2
RD23
RD22
DVDD3
DACVSSC
DACVDDB
YUV3/CVBS
DACVDDA
DACVSSA
DVDD18
(PD) DQM3
DACVSSB
YUV5/B
YUV1/Y
XRWE
CKE
YUV6/R
DVDD3
YUV4/G
YUV2/C
(PD) ALRCK
ABCK
ACLK
DVDD3
SPLRCK
SPDATA
SPMCLK
YUV7/ASDATA5
(18) DVSS
(PD) ASDATA1
(PD) ASDATA2
(PD) ASDATA3
(PD) ASDATA0
(PD) RD21
(PD) RD20
(PD) RD19
(PD) RD18
(PD) RD17
(PD) RD16
INT0# (PU)
PRST# (PU)
0.0 NC
V+3D 1.8V
3.3V
(V+3D)
RVREF/V_ADIN3
(PU) RD31/ASDATA5
VSYNC/V_ADIN1
HSYNC/V_ADIN2
DACVDDC
VREF
FS
192
191
190
189
YUV0/CIN
SPBCK/ASDATA5
RESET
FROM/TO DISRLAY
(CP601)DVDD3
1.8 NC
V_OUT
VSS NC
CT
VDD
3.3 3.3
STB
DGND
DGND
FLDC+
-28V
FLDC-
CLK
DI(M to F)
DO(F to M)
IR
V+3E
: VIDEO SIGNAL ROUTE
(RF) : RF SIGNAL ROUTE
(SY) : S VIDEO SIGNAL ROUTE (Y)
(SC) : S VIDEO SIGNAL ROUTE (C)
(R/CR) : VIDEO SIGNAL ROUTE (R/CR)
(G/Y) : VIDEO SIGNAL ROUTE (G/Y)
(B/CB) : VIDEO SIGNAL ROUTE (B/CB)
(D) : AUDIO DATA SIGNAL ROUTE
(DA) : AUDIO SIGNAL ROUTE (Digital)
(R/CR)
(G/Y)(B/CB)
(R/CR)
(G/Y)
(B/CB)
4
6
2
5/7A
6/7A
4/7A
7/7A
CP601
B
A1/7
DV-696AV-S
20
1234
1234
C
D
F
A
B
E
3.5 DVD MT PCB ASSY(2/7)
D2+
1
3
D1+
4
D1-
6
D0+
7
D0-
9
CLK+
10
D2-
HDMI CONNECTOR
CP5901
DVD
Loader
(DM-4)
MPEG/MICON IC
IC4002
MT1389EXE/B2-L
X4001
27MHz
IOA, V20
C
RF, A, B, C, D, E, F, MDI1
LD_DVD, LD_CD Q2302~2305
LD DRIVE
LDO1, LDO2
MOTOR DRIVER IC
IC2301
LA6565VR-TLM-E
DMSO, FMSO,
TROPEN, TRCLOSE,
TRSO, FOSO,
STBY, V1P4
T+/-, F+/-,
LOAD+/-,
MOT_SLED+/-,
MOT_SPDL+/-
OPU
SPINDLE/
STEPING/
SLED
MOTOR
LIMIT, TRIN, TROUT,
16Mbit FLASH
IC4004
S29AL016D70TFI020
MA0~MA11, DQ0~DQ15,
DQM0, DQM1, DBA0, DBA1,
SDCLK, SDCKE, DWE#,
DRAS#, DCAS#, DCS#
A
D
A0~A20, AD0~AD7,
PRD#, PCE#, PWR#
64Mbit SDRAM
IC4005
EM638165TS-7G A
A
SDA
16
CLK-
12
HOTPLUG
19
POWER
18
15 SCL
HDMI TRANSMITTER IC
IC5901
MT1392E/C-L
SCL
SDA
92_Y0~Y7
92_VCK, 92_ACLK, XO
ASPDIF
EEPROM IC
IC4001
BR24L08FJ-WE2 SCL
A
SDA
HDMI_SCL
HDMI_SDA
H
A, B
RESET IC
IC4003
BD5229G-TR
A
RESET
DVD LOADER/MPEG BLOCK DIAGRAM
A2/7
A2/7
MEMORY BLOCK
1/7A
1/7A
7/7
A
DVD MT PCB ASSY
(/DXZTRA, /RLFXZT : A2J009A130)
(/RPWXZT, /RTXZT : A2J012A130)
DV-696AV-S 21
5678
5678
C
D
F
A
B
E
S29AL016D70TFI020
16Mbit FLASH IC
A2/7
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE :THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
DURING PLAYBACK.
MEASURED WITH THE DIGITAL TESTER
NOTE : THE DC VOLTAGE EACH PART WAS
DV-696AV-S
22
1234
1234
C
D
F
A
B
E
3.6 DVD MT PCB ASSY(3/7)
CP2301
LD07T2-24ND-03
PICK-UP(GOLD)
1
10
11
12
13
14
15
16
17
18
19
2
20
21
22
23
24
3
4
5
6
7
8
9
CP2302
00_6232_005_006_800+
LOADING
1
2
3
4
5
Q2301
KTC3875S_Y_RTK
VCR_CTL
CP2303
00_6232_006_006_800+
SLED/SPINDLE
1
2
3
4
5
6
S
DG
Q2306
2SK3018T106
VCR_CTL
S
DG
Q2307
2SK3018T106
VCR_CTL
IC2301
LA6565VR-TLM-E
MOTOR DRIVER
123
3839
4
4041424344
567
C2302
0.1 B
C2303
0.1 B
C2301
0.1 B
C2323
0.1 B
C2322
0.0022 B
C2313
0.01 B
C2312
1B
C2314
1B
R2308
10K
R2307
100K
R2309
10K
R2306
100K
R2341
10K
R2343
10K
R2338
10K
R2319
150K
R2329
1
R2342
680K
R2331
150K
R2310
2.7K R2337
5.6K
R2311
10K
R2312
10K +-1%
R2313
10K +-1%
TP2304
TP2305
TP2306
TP2309
TP2310
TP2311
TP2312
TP2313
TP2314
TP2315
TP2316
TP2317
TP2318
TP2319
TP2308
TP2307
TP2320
TP2321
TP2322
TP2323
TP2302
JG002
JG003
JG004
JG005
JG006
JG007
TP2324
TP2325
TP2326
TP2327
TP2328
TP2303
JG001
TP2329
W864
W865
IOA
V+5S
V+5S
F
V20
E
D
C
IOA
RF
B
A
MDI1
T+
T-
F+
F-
TRSO
LOAD-
LOAD+
TROUT V+6A
TRIN
V+3F
OPO
OP-
OP+
LIMIT
MOT_SLED-
MOT_SLED+
MOT_SPDL+
MOT_SPDL-
V+3F
TRCLOSE
TROPEN
LOAD-
LOAD+
T-
LOAD+
LOAD-
GND
OPEN
CLOSE
NC
0.0
4.9
0.0
0.0
0.2
5.0
0.0
0.0
0.0
SW(GND)
LIMIT SW
SLD-
SLD+
SPD-
SPD+
VRCOM
TRKG DRV
TRKG RTN
FOCS RTN
FOCS DRV
VCC
D
B
VR780(CD)
VRF(RF_OUT)
SW1(DVD/CD)
C
E
VS
F
GND
A
VR650(DVD)
GND
GND
LD_DVD(650)
LD_CD(780)
PD/GND
NC
FWD
REV
VCC2
VLD-
VLD+
VD4+ VIN4
VIN4-
MUTE234
MUTE1
VCONT
S-GND
0.0 4.0 3.3 3.3
TRACK
1.4 1.4
NC
0.0 5.9 0.10.0 0.8 2.6
NC
(F) (F)
(E) (E)
(D) (D)
(C) (C)
(B) (B)
(RF) (RF)
(A) (A)
A3/7
To PICKUP
DVD MT PCB ASSY
(/DXZTRA, /RLFXZT : A2J009A130)(/RPWXZT, /RTXZT : A2J012A130)
A3/7
LOADER/MOTOR DRIVE BLOCK
CD2302
E
CD2301
D
MOTOR DRIVER
DV-696AV-S 23
5678
5678
C
D
F
A
B
E
Q2304
KTA1504S_Y_RTK
LD DRIV for CD
Q2305
KTA1504S_Y_RTK
LD DRIV for DVD
Q2302
KTA1504S_Y_RTK
LD DRIV for CD
Q2303
KTA1504S_Y_RTK
LD DRIV for DVD
10 11 12 13 14 15 16 17 18 19 20 21 22
23242526272829
3031323334353637
89
C2305
0.1 B
C2311
0.01 B
C2310
0.01 B
C2307
1B
C2309
0.1 B
C2308
0.1 B
C2320
10010V YK
C2321
10010V YK
C2306 10010V YK
R2316
10K+-1%
R2328
10K+-1%
R2330
10K+-1%
R2322
4.7
R2320
4.7
R2323
4.7
R2321
4.7
R2327
4.7K
R2326
4.7K
R2318
10K +-1%
R2317
10K +-1%
R2325
15K +-1%
R2335
2.2
R2334
2.2
R2332
1.2
R2333
1.2
TP2336
TP2333
TP2334
TP2332
TP2341
JG010
JG008
TP2342
JG009
TP2339
TP2330
TP2338
TP2337
W807
NOTE : THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
V20
A
B
C
D
E
V+3F F
MDI1
LDO2
LDO1
IOA
V1P4
LDO1
LIMIT
TROUT
TRIN
STBY
DMSO
FMSO
TRCLOSE
TROPEN
TRSO
FOSO
LDO2
OPO
OP+
OP-
RF
V+3F
V+5S
FOSO
V+6A
D_GND
M_GND
STBY
DMSO
V1P4
FMSO
MOT_SPDL-
MOT_SPDL+
MOT_SLED-
MOT_SLED+
T+
F-
F+
FROM POWER PORT
FROM/TO MPEG/MICON/DSP
3.3
0
3.3
0
3.3
3.3
3.1 2.5 2.5
3.1
2.0 2.0
CD
DVD
RF33
VD4-
VD3+
VD3-
VD2+
VD2-
VD1-
VD1+
VCC1
VCCS
VIN1+A
VIN1-A
VIN 1
VIN3
VIN3-
VIN2
VIN2-
VIN2+
REG-OUT
VREF-OUT
VREF-IN
NC
PGND1
PGND2
VC2
1.4
NC
NC
NC
REG-IN
0.0
NC
VO_OP
VIN-OP
VIN+OP NC
NC
NC
NC
1.41.41.1
FOCUS
1.41.4
2.5 2.5 2.6 0.0 0.0 2.72.5 5.9 5.9 1.4 1.4 1.43.91.4
NC
SPINDLE
SLED
THE DC VOLTAGE EACH PART WAS
MEASURED WITH THE DIGITAL TESTER
DURING PLAYBACK.
NOTE :
(RF) : RF SIGNAL ROUTE
(A)
(RF)
(B)
(C)
(D)
(E)
(F)
1/7A
7/7
A
A3/7
DV-696AV-S
24
1234
1234
C
D
F
A
B
E
3.7 DVD MT PCB ASSY(4/7)
Q8006
KRC407-RTK/P
MUTE CTL
Q8009
KRC407-RTK/P
MUTE CTL
Q8004
KRC407-RTK/P
MUTE CTL
Q8003
KRC407-RTK/P
MUTE CTL
Q8007
KRC407-RTK/P
MUTE CTL
Q8002
KRC407-RTK/P
MUTE CTL
Q8020
KRC407-RTK/P
MUTE CTL
IC8003 PCM1742KEG/2K
AUDIO DAC (L,R)
1
1011
1213141516
2345678
9
IC8005 PCM1742KEG/2K
AUDIO DAC (Ls,Rs)
1
1011
1213141516
2345678
9
IC8004 PCM1742KEG/2K
AUDIO DAC (C,Lfe)
1
1011
1213141516
2345678
9
D8004
1SS355
D8005
1SS355
D8006
1SS355
D8003
UDZS6.8B
CP8001
A2001WV2-2P 1
2
Q8008
KTC3875S_Y_RTK
REF GEN
Q8012
KTC3875S_Y_RTK
REF GEN
Q8011
KTC3875S_Y_RTK
REF GEN
Q8005
KTC3875S_Y_RTK
REF CTL
Q8014
KTA1504S_Y_RTK
MUTE CTL
Q8013
KTA1504S_Y_RTK
MUTE CTL
Q8010
KTA1504S_Y_RTK
MUTE CTL
Q8001
2SA1036K
P.CON+3.3V R8024 5.6K
R8018
10
R8017
10
R8029
4.7K
R8026
5.6K
R8019 2.2K
R8038
6.8K
R8023
6.8K
R8028
4.7K
R8020
2.2K
R8021
2.2K
R8025
680K
R8022
2.2K
R8004
33
R8027
4.7K
R8032
270K
R8033
10K +-1%
R8030
270K
R8031
10K +-1%
R8001
100
R8002
100
R8036
10K +-1%
R8037 270K
R8049
R8035
10K +-1%
R8034
270K
R8009
1K
R8011
8.2K
R8005
10K
R8008
10
R8007
10
R8006
10
R8003
100
R8012
22K
TP8001
TP8002
TP8003
TP8011
W801
W879
W878
W866
C8037
0.1 B
C8015
0.1 B C8020
0.1 B
C8014
0.1 B
C8026
330P CH
C8023
330P CH
C8034
0.1 B
C8025
330P CH
C8017 1 B
C8013
0.001 B
C8036
0.1 B
C8030 1 B
C8039
1B
C8019
0.1 B
C8004
1B
C8002
1B
C8035
10010V YK
C8033
10010V YK
C8031
2206.3V YK
C8038
10010V YK
C8028
2206.3V YK
C8032
10010V YK
C8029
10006.3V YK
C8016
1025V KA
C8027
4716V YK
IC8001 TC7SHU04FU(TE85L_F
INVERTER
123
45
B8001
MMZ1608R102CT
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE.
NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
V+12AT
XAMUTE
XMMUTE
SD
SCK
DAC_XCS0
ABCK XMMUTE
ALRCK SD
ACLK
ASPDIF SCK
ASDAT0 DAC_XCS0
ASDAT1 ACLK1
ASDAT2
V+3A
V+12
V+12AT
V+5A
D_GND
ABCK1
ASDAT2
ALRCK
V+5A
V+3A3
V+12AT
XMMUTE
SD
V+3A SCK
DAC_XCS0
V+3A3 ACLK1
V+3A2
V+3A1
V+5A
AUDIO_L
AUDIO_R
GND ABCK1
ASDAT1
ALRCK
V+5A
ABCK ABCK1 V+3A2
ABCK0
V+12AT
V+12
XAMUTE
SD
ACLK1 SCK
DAC_XCS0
ACLK0
VREF_C
VREF_S
ACLK
VREF_F
ABCK0
ASDAT0
ALRCK
V+5A
V+3A1
1.6
0
0
(CP8102)
SPDIF
GND
FROM POWER PORT
TO VIDEO
NC
CS
SCK
ZERORZEROA
VCOM
GND_A
PCMMCK
ZEROL/MA
SI
PCMBCK
PCMDATA
PCMLRCK
GNDD
VCC
VOUTL
VOUTR
VDD
GND_A
VCOM
ZERORZEROA
ZEROL/MA
SI
SCK
CS
PCMMCK
PCMBCK
PCMDATA
PCMLRCK
GNDD
VDD
VCC
VOUTL
VOUTR
1.6
0
03.2 0
0
1.51.6
0.9
2.6
0
02.6
0
00
0
0
5.8
6.312.5
12.5
5.8
6.3
5.8
12.5
6.3
6.8
6.312.5
NC
0
3.3
4.9
2.5
2.4 2.4
3.1
3.1
0
0
0
0
1.6
1.61.5
1.5 0
3.3
4.8
2.4 0
2.4
3.2
0
0
3.2
3.2
1.6
2.4
1.6
0
1.5 PCMMCK
CS
SCK
SI
ZEROL/MA
ZERORZEROA
VCOM
GND_AVOUTR
VOUTL
VCC
VDD
GNDD
PCMLRCK
PCMDATA
PCMBCK
NC
1.5
0
3.3
4.8
2.4
2.4 0
2.4
3.2
0
0
3.2
3.2
1.6
1.6
0
FROM/TO MPEG/MICON/RF-AMP
1.60.9 1.5
0
3.2 0
0
0
3.3 3.3
2.7
NC 1.500
1.63.3
GND
VCC
3.0
(D) : AUDIO DATA SIGNAL ROUTE
(DA)
(D)
(D) (D)
(D)
(D)
(D)
(DA) : AUDIO SIGNAL ROUTE (Digital)
(DA)
: AUDIO SIGNAL ROUTE (L ch)
7/7A
5/7A
2/2F
1/7A
A4/7
DVD MT PCB ASSY
(/DXZTRA, /RLFXZT : A2J009A130)(/RPWXZT, /RTXZT : A2J012A130)
A4/7
AUDIO JACK BLOCK
AUDIO DAC (C,Lfe)
AUDIO DAC (Ls,Rs)
AUDIO DAC (L,R)
INVERTER
DV-696AV-S 25
5678
5678
C
D
F
A
B
E
H1H2
E
H1H2
E
J8002
RCA-405A-06
LS/RS/C/LFE
1
23
4
56
H1H2
E
J8001
RCA-207B-02
L/R 1
23
Q8015
KTC2875-B
MUTE SW
Q8017
KTC2875-B
MUTE SW
Q8021
KTC2875-B
MUTE SW
Q8023
KTC2875-B
MUTE SW
Q8016
KTC2875-B
MUTE SW
Q8018
KTC2875-B
MUTE SW
CAUTION: DIGITAL TRANSISTOR
R8068
22K
R8067
22K
R8074
1K
R8071
220 +-1%
R8072
220 +-1%
R8077
1K
R8076
220 +-1%
R8069
22K
R8070
22K
R8063
10K +-1%
R8064
18K +-1%
R8041
10K +-1%
R8040
270K
R8058
10K+-1%
R8055
18K +-1%
R8052
10K+-1%
R8048
18K +-1%
R8053
10K +-1%
680K
R8050
18K +-1%
R8046
10K +-1%
R8045
18K +-1%
R8054
680K
R8065
680K
R8092
220 +-1%
R8094
220 +-1%
R8093
220 +-1%
R8059
18K +-1%
R8061
10K +-1%
R8043
10K +-1%
R8042
270K R8096
220 +-1%
R8087
220 +-1%
R8088
1K
R8090
1K
R8066
22K
R8075
22K
R8073
1K
R8099
220 +-1%
R8081
220 +-1%
R8079
1K
R8078
220 +-1%
R8095
220 +-1%
TP8012
TP8013
TP8014
TP8017
TP8019
TP8015
C8046
560P CH
C8056
100P CH
C8059
100PCH
C8063
0.1 B
C8064
0.1 B
C8067
0.1 B C8057
100PCH
C8055
100P CH
C8051
560P CH
C8045
560P CH
C8044
560P CH
C8049
1B
C8042
560P CH
C8043
560P CH
C8053
100P CH
C8052
1B
C8054
1B
C8010
330P CH
C8009
330P CH
C8008
330P CH
C8062
100PCH
C8006
330P CH
C8005
330P CH C8007
330P CH
IC8007 RC4580IDR
AUDIO LPF&AMP
1234
5678
IC8006 RC4580IDR
AUDIO LPF&AMP
1234
5678
IC8008 RC4580IDR
AUDIO LPF&AMP
1234
5678
C8040
10010V YK
C8050
10010V YK
C8060
4716V YK
C8065
4716V YK
C8068
4716V YK
C8048
10010V YK
C8061
4716V YK
C8047
10010V YK
C8041
10010V YK
C8069
4716V YK
C8058
4716V YK
C8066
4716V YK
DURING PLAYBACK.
MEASURED WITH THE DIGITAL TESTER
NOTE:THE DC VOLTAGE EACH PART WAS
V+12
CENTER
SL
SR
LFE
LRSLSR C LFE
0
0.6 0
0.6 0
0
+
-
-
+
+VS
-VS
5.7
5.7
5.7
5.7
5.7
12.2
5.7 0
+
-
-
+
+VS
-VS
5.7
5.7
5.7
5.7
5.7
5.7
12.2
0
+
-
-
+
+VS
-VS 0
5.7
5.7
5.7
12.2
5.7
5.7
5.7
0
0
-0.7
00
-0.7
0
0
0.6
0
0
0.6
A4/7
AUDIO LPF&AMP
AUDIO LPF&AMP
AUDIO LPF&AMP
9
7
11
10
6
8
DV-696AV-S
26
1234
1234
C
D
F
A
B
E
3.8 DVD MT PCB ASSY(5/7)
IC7301 LA73054
VIDEO DRIVER 6CH IC
1101112131415161718
19
2
20 21 22 23 24 25 26 27 28 29
3
30 31 32 33 34 35 36
456789
Q7302
KRC407-RTK/P
P-H/I-L
C7308
1 B
C7309
1 B
C7313
0.1 B
C7304
0.1 B
C7312
0.1 B
C7303
4706.3V YK
C7311
10010V YK
R7315
1K
TP7303
TP7302
W877
W886
W887
W888
SQUEEZE
LETTER
LETTER
SQUEEZE
VSEL1
I/XP
R/CR
B/CB
G/Y
S_C
S_Y
CVBS
VSEL1
B/CB
R/CR
V+6A
V+3F I/XP
P-H/I-L
V+5V
V+5
D_GND
D_GND
FROM MPEG/MICON/DSP
FROM POWER PORT
FROM POWER PORT
VCC1
CVBS in
MUTE1
SQ
LE
C in
GND11
Y1 in
YC-MIX
Y2 in
MUTE2
CB in
AMP2
CR in
GND12
REG
GND26
CR out
GND25
CB out
VCC22
Y2 out
GND24
GND23
Y1 out
GND22
C-DC out
C out
GND21
CVBS out
VCC21
DRIVE1
AMP1
IN SW
LPF
(9dB=H,6dB=L)
(MIX=H,OFF=L)
(RGB=H,YUV=L)
(P=H,I=L)
(9dB=H,6dB=L)
(ON=H,OFF=L)
(ON=H,OFF=L)
DRIVE2
(1D=H,2D=L)
(1D=H,2D=L)
+5V
GND
0
2.8
0
2.7
0
2.6
0
5
0
0
2.8
0
0
2.8
1.2
0
2.7
5.0
0
0
5
0
0
0
0
0
0
0
2.9
2.5
2.0
2.0
5.0
2.4
2.5
0
0
0
3.4
C7304
0.1 B
C7306
1 B
C7307
1 B
C7305
1 B
CVBS
S_C
S_Y
G/Y
(R/CR)
(G/Y)
(B/CB)
(SC)
(SC) (SC) (SC)
(SY)
(GY)
(SY)
(GY)
(B/CB) (B/CB)
: VIDEO SIGNAL ROUTE
(SY) : S VIDEO SIGNAL ROUTE (Y )
(SC) : S VIDEO SIGNAL ROUTE (C)
(R/CR) : VIDEO SIGNAL ROUTE (R/CR )
(G/Y) : VIDEO SIGNAL ROUTE (G/Y )
(B/CB) : VIDEO SIGNAL ROUTE (B/CB )
(D) : AUDIO DATA SIGNAL ROUTE
(DA) : AUDIO SIGNAL ROUTE (Digital)
: AUDIO SIGNAL ROUTE (L ch)
(R/CR) (R/CR)
DVD MT PCB ASSY
(/DXZTRA, /RLFXZT : A2J009A130)(/RPWXZT, /RTXZT : A2J012A130)
A5/7
VIDEO JACK BLOCK
A5/7
1/7A
7/7
A
7/7A
DV-696AV-S 27
5678
5678
C
D
F
A
B
E
H1H2
E
H1H2
E
J7302
RCA-405A-08
CVBS/Y/U/V
1
23
4
56
C7330
0.1 B
C7315
4706.3V YK
C7318
10006.3V YK
C7314
4706.3V YK
C7316
10006.3V YK
C7329
4706.3V YK
R7303
75 +-1% R7304
75 +-1% R7305
75 +-1%
R7302
75 +-1%
R7317
75 +-1%
R7316
75 +-1%
R7301
10K
TP7301
W872
W873
W871
B7304
MMZ1608R102CT
B7305
MMZ1608R102CT
ASP
S_C_OUT
S_Y_OUT
CVBS_OUT
U_OUT
V_OUT
Y_OUT
Y
U
V
CVBS
ASP
NOTE : THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
THE DC VOLTAGE EACH PART WAS MEASURED
WITH THE DIGITAL TESTER DURING PLAYBACK.
NOTE :
CAUTION: DIGITAL TRANSISTOR
J7301
DIN-409A
S-VIDEO OUT
12 34
56
YC
(R/CR)
(SY)
(SC)
12 17 16
13
14 15
A5/7
DV-696AV-S
28
1234
1234
C
D
F
A
B
E
3.9 DVD MT PCB ASSY(6/7)
W890
W889
W888
W885
W886
W887
ABCK
ACLK
ALRCK
ASDAT0
ASDAT1
ASDAT2
TP5920
TP5921
TP5922
TP5923
TP5924
92_A7
92_A6
TRAP2
TRAP1
TRAP0
(I2C)
(I2C)
C5908
10010V YK
IC5901
MT1392E/C-L
HDMI TRANSMITTER
110111213141516171819 220
21 22 23 24 25 26 27 28 29
3
30 31 32 33
456
6869
7
70717273747576777879
8
80
9
C5904
0.1 B
C5901
0.1 B
C5903
0.1 B
C5905
0.001 B
C5902
0.1 B
R5923 100
R5922
1K
R5906
820
TP5917
TP5931
W850
W851
B5905
MMZ1608R102CT
ASPDIF
D_GND
V+3H
DVDD18
V+5H
92_SDATA3
NC
NC
NC
DVDD18
92_VCK
92_Y0
92_Y1
92_Y2
92_Y3
92_Y4
92_Y5
92_Y6
92_Y7
SCL
SDA
92_VCK
92_Y0
92_Y1
92_Y2
92_Y3
92_Y4
92_Y5
92_Y6
92_Y7
SCL
SDA
PWDN#
URST#
XO
FROM/TO MPEG/MICON/DSP
NCNCNCNCNC
NC
NC
NC
NC
NC
NC
NC
NC
DVDD33
VCK
DVSS
SSD
DVD18
CLK
INT
DVSS
G
AVSS
B
R
SPDIF
AD3
AD1
AD2
AD0
ACK
ABCK
ALRCK
DVDD18SSCK
C1 (PD) DVSS
2
1
C0 (PD)
19
20
C2 (PD)
C3 (PD)
C4 (PD)
C5 (PD)
C6 (PD)
C7 (PD)
Y0 (PD)
Y1 (PD)
Y2 (PD)
Y3 (PD)
Y4 (PD)
Y5 (PD)
Y6 (PD)
Y7 (PD)
/RST (PD)
A7/GPO0 (PD)
A6/GPO1 (PD)
TRAP2/GPO2 (PD)
TRAP1/GPO3 (PD)
TRAP0/GPO4 (PD)
NO MOUNT(READY)
/PWDN (PU)
(92_DV33)
VCK
0.0
2.6
0.0
0.0
0.0
0.0
0.0
0.0
0.0
3.4
1.5
0.0
1.0
1.0
1.0
1.0
1.5
1.7
1.0
1.1
1.8
3.3
3.3
1.1
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
3.3
3.0
0
0
1.2
1.2
1.8
1.8
1.8
3.2
3.2
URST#
PWDN#
ASPDIF
ACLK
ABCK
ALRCK
ASDAT0
ASDAT1
ASDAT2
HDMI_SCL
HDMI_SDA
XO
DVD MT PCB ASSY
(/DXZTRA, /RLFXZT : A2J009A130)(/RPWXZT, /RTXZT : A2J012A130)
A6/7
HDMI BLOCK
A6/7
1/7A
1/7A
DV-696AV-S 29
5678
5678
C
D
F
A
B
E
W897
W898
VSYNC
HSYNC
TP5928
34 35 36 37 38 39 40
41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
61626364656667
CP5901
1903015-3
HDMI CONNECTOR
1
10
11
12
13
14
15
16
17
18
19
2
3
4
5
6
7
8
9
L5901
ACM2012H-900-2P
1
23
4
L5902
ACM2012H-900-2P
1
23
4
L5903
ACM2012H-900-2P
1
23
4
L5904
ACM2012H-900-2P
1
23
4
C5925
0.1 B
C5912 0.1 B
C5911 0.1 B
C5913 0.1 B
C5918 0.1 B
C5914 0.1 B
C5910
0.0056 B
C5920
0.1 B
C5916
0.1 B
C5915
0.1 B
C5917 0.1 B
C5919
476.3V KA
C5921
1025V KA
R5920
1.5K
R5919
1.5K
R5916
510 +-1%
R5928
10
R5918 560 +-1%
TP5903
TP5901
TP5902
W829
W830
W831
B5902
MMZ1608R102CT
A_GND
92DAC_AVDD3
92_AVDD3
92PLL_AVDD3
FS_1392
VREF_1392
TX2+
TX2-
TX1+ TX2+
TX1-
TX2-
TX0+
TX1+
TX0-
TX1-
TXC+
TXC- TX0+
TX0-
TXC+
TXC-
PLLC0
HDMI_SCL
HDMI_SDA
HPD
V+5H
D2+
D2-S
D2-
D1+
D1-S
D0+
D0-S
D0-
CLK-S
CLK-
CEC
SCL
SDA
GND
POWER
HOTPLUG
NC
D1-
CLK+
NC
NC
NC
NCNCNC
NC
MSCK/GPO5
GPO8
GPO9
GPO10
AVDD
VREF
FS
AVSS
AVDD
AVSS
AVDD
AVSS
AVSS
TCK-
TCK+
AVDD
TX0-
TX0+
AVSS
TX1-
TX1+
AVDD
TX2-
TX2+
GPO7 (PD)
HTPLG (PD)
42
41
SWING
AVSS59
60
AVDD
AVDD
PLLC1
PLLC0
AVSS
MSD/GPO6 (PU)
TX2+
TX2+
TX1+
TX1-
TX0+
TX0-
TXC-
TXC+
0.0
2.7
0.0
0.0
0.0
0.0
5.0
0.0
0.0
1.3
3.3
3.3
0.0
0.0
3.3
0.0
3.3
0.0
2.9
3.3
0.0
0.0
0.0
3.3
0.0
3.3
0.3
0.3
03
A6/7
DV-696AV-S
30
1234
1234
C
D
F
A
B
E
3.10 DVD MT PCB ASSY(7/7)
CP4003
A2001WV2-14P
1
10
11
12
13
14
2
3
4
5
6
7
8
9
IC4006
LM1117S-ADJ
REG+1.8V IC
123
C4095
476.3V KA
C4086
1B
C4093
1B
C4094
0.1 B
C4096
1B
C4112
0.001 B
C4116
0.001 B
C4087
116V B
C4122
0.1 B
R4013
39 +-1%
R4012
68 +-1%
R4011
15
TP4031
W820
FROM/TO POWER
(CP502)
GND
P.CON+5V
STBY L
FL DC-
FL DC+
AT+3.3V
GND
P.CON+12V
AT+12V for MUTE
GND(M)
GND(D)
P.CON+6V
AT+3.3V
-28V
ADJVIN VOUT
1.8 0.63.3
+3.3V
THE DC VOLTAGE EACH PART WAS MEASURED
WITH THE DIGITAL TESTER DURING PLAYBACK.
NOTE :
DVD MT PCB ASSY
(/DXZTRA, /RLFXZT : A2J009A130)(/RPWXZT, /RTXZT : A2J012A130)
A7/7
POWER PORT BLOCK
CP502
F1/2
A7/7
DV-696AV-S 31
5678
5678
C
D
F
A
B
E
IC5902 PQ1K503M2ZPH
HDMI+5V REG(300mA)
123
564
C4099
0.001 B
C4098
1B
C4056
0.01 B
C4105
100P CH
C5922
1B
C5923
0.01 B
C5924
0.1 B
C4100
2206.3V YK
R4058
100
R5901
10K
R5921
22K
W837
W822
W821
W838
B4002
MMZ1608R102CT
B4001
MMZ1608R102CT
V+5A V+5A
V+12AT V+12AT
V+12 V+12
D_GND
V+6A V+6A
V+5S V+5S
V+3F V+3F
D_GND
M_GND
V+5H V+5H
V+3H V+3H
DVDD18 DVDD18
V+3 V+3
V+3E V+3E
V+1R8 V+1R8
PWDN#
FLDC-
FLDC+
-28V
D_GND
D_GND
TO AUDIO JACK
TO LOADER/MOTOR DRIVE
TO HDMI
FRROM/TO MEMORY
FROM/TO MPEG/MICON/DSP
(HDMI)
(HDMI)
(AUDIO DAC)
(AUDIO AMP)
(AUDIO MUTE)
(CORE)
(MPEG/SDRAM/FLASH)
(FIP/LED/IR/RESET)
(F/E)
(OPU)
(MOTOR)
VIN
GND GND
ON/OFF NR
VOUT
5.9
0
5.9
(HDMI)
5.0
0
1.3
NOTE : THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
4/7A
3/7
A
6/7A
2/7A
1/7
A
A7/7
DV-696AV-S
32
1234
1234
C
D
F
A
B
E
3.11 OPERATION, OPERATION 2 and OPERATION 3, 4 PCB ASSYS
Vout
B+
GND
OS651
ROM-N340TAO
1
2
3
D660
LTL-1CHEE-002A
HDMI LED(RED)
SW652
EVQ11L05R
DOWN
SW658
EVQ11L05R
TOPMENU
SW656
EVQ11L05R
MENU
SW655
EVQ11L05R
RETURN
SW653
EVQ11L05R
ENTER
SW654
EVQ11L05R
RIGHT
SW657
EVQ11L05R
UP
SW659
EVQ11L05R
LEFT
SW661
EVQ11L05R
HOMEMENU
SW666
EVQ11L05R
EJECT
SW660
EVQ11L05R
STOP
SW665
EVQ11L05R
PAUSE
SW664
EVQ11L05R
-SKIP
SW663
EVQ11L05R
PLAY
SW662
EVQ11L05R
+SKIP
SW667
EVQ11L05R
POWER
CP602
00_6232_009_102_800+
1
2
3
4
5
6
7
8
9
CP603
00_6232_009_102_800+
1
2
3
4
5
6
7
8
9
D659 1SS133
D651
1SS133
D654
1SS133
D656
1SS133
D658
1SS133
D657 1SS133
D652 1SS133
D655 1SS133
CD602
2H091303
FFC(1.0mm pitch)
CD604
2H051706
FFC(1.0mm pitch)
CP604
00_6232_005_102_800+
1
2
3
4
5
CP605
00_6232_005_102_800+
1
2
3
4
5
C668
0.01 B
R664
330 1/4W
W808W807
W804
NC
SW2
SW1
POWER
PLAY/+SKIP
STOP
(CP603)
SW1
GND
PAUSE/-SKIP
LED
SW2
V+3E
SW1
STOP
PLAY/+SKIP
PAUSE/-SKIP
GND
POWER
LED
(CP602)
SW2
V+3E
(CP605)
SW2
POWER
GND(NC)
V+3E
LED
(CP604)
SW2
POWER
GND(NC)
V+3E
LED
B C G H
OPERATION PCB ASSY
(A2I813A270 : Other)
(A2I812A270 : RTXZT_Only)
B
OPERATION 4 PCB ASSY
(A2I903ADG0)
H
OPERATION 3
PCB ASSY
(A2I903ADF0)
G
OPERATION 2 PCB ASSY
(A2I802A280)
C
OPERATION 2 PCB ASSY
SW660 : STOP
SW662 : +SKIP
SW663 : PLAY
SW664 : - SKIP
SW665 : PAUSE
OPERATION PCB ASSY
SW652 : DOWN
SW653 : ENTER
SW654 : RIGHT
SW655 : RETURN
SW656 : MENU
SW657 : UP
SW658 : TOPMENU
SW659 : LEFT
SW661 : HOMEMENU
SW666 : EJECT
OPERATION 3 PCB ASSY
SW667 : POWER
DV-696AV-S 33
5678
5678
C
D
F
A
B
E
IC651
PT6315
FIP DRIVER IC
11011
1213141516171819
2
202122
23242526272829
3
30313233
34 35 36 37 38 39
4
40 41 42 43 44
56789
V651 HNV-08SS44T
1
101112131415
16171819 2
202122
2324252627283132 56789
CD601
2H0B10
FFC(1.0mm
C6760.1 B
C658
0.1 B
C651
0.1 B
C675
0.1 B
C604
33P CH
C605
0.001 B
C674
476.3V KA
C653 476.3V KA
R651
2.2
R653
2.2 R654
2.2
R657
10K
R658
10K
R662
100K
R652
2.2
R655
1K
R656
1K
R666
2.2 1/4W
TP663
TP662
CP601
00_6232_011_102_800+
1
10
11
2
3
4
5
6
7
8
9
W809
W805
NOTE : THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
FLDC-
FLDC+
P16
P15
P14
P13
P12
P11
P10
P9
P8
P7
P6
P5
P4
P3
P2
P1
GR8
GR7
GR6
GR5
GR4
GR3
GR2
GR1
-28V
P8
P9
P10
P11
P12
P13
P14
P15
P16
P7
P6
P5 STB
P4 FP_SCK
P3 FP_DI
P2 FP_DO
P1
GR8
GR7
GR6
GR5
GR4
GR3
GR2
GR1
LED
V+3E
LED
IR
FP_SCK
FP_DI
STB
FP_DO
V+3E IR
V+3E
FLDC+
-28V
FLDC-
GND
FROM/TO MPEG/MICON/DSP
STB
VDD
3.2
0
0
0
CLK
2.9
3.2
0.7
3.4
K2
K1
DI
DO
OSC
NC
12
23
-12.0
-6.0
-18.0
-19.0 -15.6-19.0-9.5-13.0-9.5-12.6-13.0-6.0
LED1
LED2
LED4
34
VDD
44
NC
NC
NC
-18.0
-18.0
-18.0
-18.0
-18.0
-18.0
-18.0
-18.0
-16.0 -16.0 -16.0 -16.0-16.0 0
0
NC
GND
P16
P15
P14
P13
P12
P11
P10
P9
P8
P7
P6
GR12
P5
P4
P3
P2
P1
-28V
GR10
GR11
GR9
GR8
GR7
GR6
GR5
GR4
GR3
GR2
GR1
GND
LED3
-16.0-18.0-18.0-18.0
0
0
0
NC
NC
NC
FL-
FL-
FL+
FL+
P16
P15
P14
P13
P12
P11
P10
DVDCD TRACK ALL REPEAT A B
P9
P8
P7
P6
P5
P4
P3
P2
P1
G8
G7
G6
G5
G4
G3
G2
G1
3.3
3.3
-25.1
-25.1
-25.1
-25.1
-25.1
-25.1
-25.1
-25.1
-20.5
-26.8
-26.8
-26.8
-20.5
-20.5
-22.7
-20.5
-20.5
-22.7
-26.8
-26.8
-20.5
-22.7
-22.7
-26.8
-19.7
-19.7
-22.3
-22.3
DGND
DGND
FLDC+
-28V
FLDC-
DI (M to F)
V+3E
STB
DO (F to M)
IR
CLK
(CP4002)
THE DC VOLTAGE EACH PART WAS MEASURED
WITH THE DIGITAL TESTER DURING PLAYBACK.
NOTE :
D668
D669
D667
/DXZTRA : D667, D669
/RLFXZT : D667, D669
/RPWXZT : D667, D669
/RTXZT : D668
CP4002
A1/7
B
18
DV-696AV-S
34
1234
1234
C
D
F
A
B
E
3.12 POWER PCB ASSY (1/2)
D505
1N4005-EIC
D511
1H3-E
D509_1
RL106F-E
D519
1F5-E
D510
FR155-F
D515
1S40-E
D512
FR155-F
D506
1N4005-EIC
D503
1N4005-EIC
D502
1N4005-EIC
D513
1H3-E
D508
MTZJ5.6B-EIC
LES PIECES REPAREES PAR UN ETANT
DANGEREUSES AN POINT DE VUE SECURITE
N'UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES
ATTENTION:
SINCE THESE PARTS MARKED BY ARE
CRITICAL FOR SAFETY,USE ONES
DESCRIBED IN PARTS LIST ONLY
CAUTION:
F501_1
1.6 A250 V
L501
SS11V-03550-CH
12
34
FH501_1
EYF-52BCY FH502_1
EYF-52BCY
IC504
PS2561AL1-1-V(W)
PHOTO COUPLER
1
2
34
R502
1.8 1W
2 1
POUR UNE PROTECTION CONTINUE LES RISQUES D'INCEIE
N'UTILISER QUE DES FUSIBLE DE MEME TYPE
1.6A 125V{F501}
ATTENTION:
IC501 KIA431A-AT
VOLTAGE CTL IC
123
1 2
FOR CONTINUED PROTECTION AGAINST FIRE HAZARD,
REPLACE ONLY WITH THE SAME TYPE FUSE
1.6A 125V{F501}
CAUTION:
1.6A 250V
1.6A 250 V
R507
10 1/4W
T501 81291294
10
11
12
13
14
15
16
2
3
4
6
7
89
C511
82400V UP
C518
0.001250V KX
C508
680P CH
C516
0.0022250V KX
C513
47P2KV SL
C515_1
0.01400V ECQP
C505
100P2KV R
C540
0.01 B
C503
0.1 B
C502_1
0.22275V ECQUL
C514
470P500V B
C509
1050V YK
C506
2.250V KA
R512_1
100K 1/2W
R514
1K 1/4W
R515
1K
R513
10K 1/4W
R503
1.5M 1/2W
R505
22 1/4W
R504
680K
IC502 STR-A6131M
POWER CTL IC
1234
5
678
W803
W804
B501
W4BRH3.5X6X1.0X2
NTSC
NC
NC
9.9
0
3.9 10.9
0
0
0
0
0
0
0
130
130
0
130
0
-22.5
-22.5
02 .5
9.9
GNDOUT IN
BLACK(L)
PRI SEC
WHITE(N)
CHASSIS GND
NC
D
DOCP
VCC
GND
FB/OLP STARTUP
17.5 3.90.1
130 130 130
0
0N C
POWER PCB ASSY (A2J012A240)
F1/2
POWER BLOCK
F1/2
CD501_1 1209618901
AC 220 V -240 V_
50 Hz Hz
AC 110 V -120 V_
60 Hz Hz J501
YKE31-0148N
AC INLET
DV-696AV-S 35
5678
5678
C
D
F
A
B
E
THE RESISTOR MARKED F IS FUSE RESISTOR.
THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP
IS NON POLAR ONE.
NOTE :
D532
1S40-E
D534
1SS133
D527
SR240-F
D516
1SS133
D525
1SS133
D520
1SS133
D521
1SS133
D522
1SS133
D533
MTZJ2.2B-EIC
D523
MTZJ3.6B-EIC
D517
MTZJ4.3B-EIC
D531
MTZJ27B-EIC
D535
MTZJ5.1B-EIC
D536
MTZJ3.0B-EIC
D528
MTZJ5.1B-EIC
L503
22uH TSL0808
L505
22uH
R510_1
3.3 1W
R529
220 1W
R511
68 1/4W
Q506
KTA1504S_Y_RTK
PROTECT
IC503 PQ070XF01SZH
6V REG (DVD MOTOR) IC
1234
C520
10050V YK
CD502
CU2E3301
CORD CONNECTOR
R546
3.3K 1/4W+-1%
R517
1.2K 1/4W+-1%
R542
820 1/4W+-1%
CP502
A2001WV2-14P
1
10
11
12
13
14
2
3
4
5
6
7
8
9
C531
10016V YK
C521
100016V FM
C523
47025V YK
C535
33016V YK
C526
4706.3V YK
C536
2206.3V YK
Q505
KRC102SRTK
P.CON SW
CAUTION: DIGITAL TRANSISTOR
Q511
KTC3875S_Y_RTK
REG+12V CTL
Q512
KTC3875S_Y_RTK
FL+ CTL
Q502 KTC3209_Y
-28V P.CON SW
Q501
KTC3875S_Y_RTK
PROTECT
Q509
KTC3875S_Y_RTK
REG+12V CTL
Q515
2SD1835S/T-AA
P.CON+5V REG
Q513
KTA1504S_Y_RTK
FL+ CTL
Q503
KTA1504S_Y_RTK
-28V CTL
Q504
KTA1281_Y
FL+ P.CON SW
Q510
KTA1281_Y
REG P.CON+12V SW
C501
0.01 B
C507
0.01 B
C541
0.01 B
C528
2.250V KA
C517
22025V YK
C522
10006.3V FM
C519
2235V YK
C538
2206.3V YK
C527
10010V YK
R525
100
R540
680 1/4W
R530
560
1/4W
R544
10K
R534100 1/4W
R537
1K
R548
1K
R536
10K
R541
5.6K +-1%
R526
6.8K +-1%
R545
22K+-1%
R528
22K 1/4W
R531
10K
R527
100 1/4W
R523
22K
R539
4.7K 1/4W
R518
3.3K +-1%
R516
10
R509
1K
R543
4.7K +-1%
R524
1K 1/4W
R519
3.3K
R547
22
R538
22K
R506
100
W817
W814
NOTE : THIS SCHEMATIC DIAGRAM IS THE LATEST AT
THE TIME OF PRINTING AND SUBJECT TO CHANGE
WITHOUT NOTICE
GND
P. CON+D5V
FROM/TO POWER PORT
TO DIGITAL AUDIO
4.5
12.9
5.1
20.8
21.6
0.6
0
20.7
21.5
6.8
28.4
28.4
27.8
0
0.6
19.7
19.0
19.0
0
9.9
0
3.2
0
3.2
4.5
12.3
5.0
12.6
12.3
12.9
IN GNDOUT
7.07.0 5.9 1.20
0
02.8
(CP4003)
5.17.0
5.8 P.CON+12V
P.CON+5V
FL DC-
FL DC+
GND
GND
AT+12V for MUTE
P.CON+6V
-28V
GND(M)
GND(D)
AT+3.3V
AT+3.3V
P.ON-H
THE DC VOLTAGE EACH PART WAS
MEASURED WITH THE DIGITAL TESTER
DURING PLAYBACK.
NOTE :
F1/2
F2/2
CP4003
A7/7
DV-696AV-S
36
1234
1234
C
D
F
A
B
E
3.13 POWER PCB ASSY (2/2)
FROM POWER
B8101
MMZ1608R102CT
P.CON+D5V
F2/2
POWER PCB ASSY (A2J012A240)
F2/2
DIGITAL AUDIO BLOCK
1/2E
FROM POWER
B8101
MMZ1608R102CT
P.CON+D5V
F2/2
POWER PCB ASSY (A2J012A240)
F2/2
DIGITAL AUDIO BLOCK
1/2E
DV-696AV-S 37
5678
5678
C
D
F
A
B
E
NOTE :THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE THE DC VOLTAGE EACH PART WAS MEASURED
WITH THE DIGITAL TESTER DURING PLAYBACK.
NOTE :
OS8101
RFT5CB1
OPTICAL
1
2
3
H
E
J8102
RCA-117-01
COAXIAL
1
2
CP8102(CP8001)
CU223002
1
2
Q8103
KTC3875S_Y_RTK
COAXIAL DRV
R8121
3.9K
R8123
75+-1%
R8122
220
R8106
2.2K
R8107
1.8K
R8124
100K
TP8101
TP8102
C8119
1B
C8103
100P CH
C8120
0.1B
C8118
100
10V
YK
C8104
1
50V KA
ASPDIF
COAXIAL
D_GND
4.9
2.1
2.7
SPDIF
GND
GND
VCC
INPUT
28
27
F2/2
4/7A
DV-696AV-S
38
1234
1234
C
D
F
A
B
E
3.14 WAVE FORMS
1.0 V
10
11
500 µs
1.0 V
12
10 µs
200 mV
8
500 µs
1.0 V
10 µs
500 mV
13
9
500 µs
1.0 V
4
20 µs
1.0 V
20 µs
1.0 V
3
200 ns
1.0 V
AUDIO JACK
6
6
500 µs
1.0 V
7
500 µs
1.0 V
VIDEO JACK
1
10 ns
500 mV
2
2 ns
500 mV
500 µs
7
50µs
1.0V
8
50µs
1.0V
IC4001 - pin 6 (SDCL)
IC4001 - pin 5 (SDA) TP8012- (CENTER)
TP8015- (SR)
J7302 -pin 6 (CVBS)
J7302 -pin 5 (Y)
TP8013- (LFE)
TP8014- (SL)
IC4002 - pin 156 (SDCLK)
IC4002 - pin 228 (XTAL)
TP8017 (L)
TP8019 (R)
IC4002 - pin 225 (ASPDIF)
TP4039 (ACLK)
TP4095 (FP-SCK)
DVD MT PCB ASSY
AThe following waveforms were measured at the point of the corresponding
balloon number in the schematic diagram
NOTE:
DV-696AV-S 39
5678
5678
C
D
F
A
B
E
20 µs
500 mV
16
10 µs
500 m V
17
1µs
500mV
18
OPERATION PCB ASSY
B
POWER PCB ASSY
E
DIGITAL AUDIO
28
200 ns
1.0 V
200 µs
500 mV
27
20 µs
500 mV
14
20 µs
500 mV
15
J7302 -pin 3 (U)
J7302 -pin 2 (V)
J7301-pin 3 ( Y )
J7301-pin 4 ( C )
J8102-pin 2 ( COAXIAL OUT )
OS8101-pin 1 ( OPTICAL 0UT )
IC651 -pin 5 (OSC)
VIDEO JACK (DVD PCB)
The following waveforms were measured at the point of the corresponding
balloon number in the schematic diagram
NOTE:
DV-696AV-S
40
1234
1234
C
D
F
A
B
E
DV-696AV-S 41
5678
5678
C
D
F
A
B
E
4. PCB CONNECTION DIAGRAM
4.1 LOADING and SW PCB ASSYS
DED021A
DED021A
1
15
5
WH
BR
CD2302
DED020A
BR
WH
YE
GR
M2603
LOADING MOTOR
M2603
SW1
CD2301
SW2
NOTE FOR PCB DIAGRAMS :
1. Part numbers in PCB diagrams match those in the schematic
diagrams.
2. A comparison between the main parts of PCB and schematic
diagrams is shown below.
3. The parts mounted on this PCB include all necessary parts for
several destinations.
For further information for respective destinations, be sure to
check with the schematic diagram.
4. View point of PCB diagrams.
Symbol In PCB
Diagrams Symbol In Schematic
Diagrams Part Name
BCE
D
D
G
G
S
S
BCE
BCE
DGS
BCEBCE
BCE
Transistor
Transistor
with resistor
Field effect
transistor
Resistor array
3-terminal
regulator
Capacitor
Connector
P.C.Board Chip Part
SIDE A
SIDE B
SIDE A SIDE B
D E
E
ED
E
D
CP2302
A
CD2302
CP2303
A
CD2301
M2601
SPINDLE
MOTOR
M2602
SLED
MOTOR
LOADING MOTOR
PCB ASSY
(CHIP MOUNTED PARTS)
LOADING MOTOR
PCB ASSY
(INSERTED PARTS)
SW PCB ASSY
DV-696AV-S
42
1234
1234
C
D
F
A
B
E
4.2 DVD MT PCB ASSY
1
21
41
61
C4060
C4053
C4063
C4061
C4048 C4049
C4050
C4047
C4045
C4043
C4044
C4042
C4041 C4040
C4039
C4037
C4036
C4034
C4033
C4032
C4031
C4029
C4028
C4027
C7317
C7313
C7304
C7305
C7306
C7307
C7308
C7309
C8036
C8017
C8013
C8025
C8067
C8034 C8015
C8020
C8023
C8064
C8037 C8014
C8019
C8026
C8042
C8043
C8063
C8004
Q8023
Q8018
Q8016
Q7302
R4054
R4052
R4048
R8041
R8065
R8088
R8090
R8081
R8020
R8028
R8032
R8070
R8079
R8078 R8095
R8027
R8034 R8049
R8067
R8073
R8071 R8094
R8022
R8029
R8017
R8018
R4050
R4047
R4046
R4043
R4040
R4038
R4025
R4027
R4024
R4020
R4069
R4068
R4067
R4066
R4065
R4064
IC8003
IC8005
IC8004
J8002
X4001
C4
R
R
CP
R40
R40
C4100
C4098
C4099
B4001
C4056
C4093
B4002
C4087
W825
W826
IC8001
W804
C4046
C8058
C8069
C8068 D8003
C8027
Q8005 Q8012
Q8011
R8040
C8050
C8039
R8025
C8040
C8041
C8016
Q8003
Q8007
C8066
C8065
R8033
C8031
C8028
C8047
C8038
C8032
Q8006
Q8002
R8019
C8060
C8061
C8033
C8048
R8035
C8035 Q8004
Q8009
C7312
R7315
C7319
R7316
C7330
R7317 R7301
CP7301_1
Q8010
Q8013
Q8014
R8021
R7305
C7318
J7302
C7315
C7314
B7304
R7302
R7303
C7316
W873
W876
W875
W872
W871
W874
B7303
C7302
R8004
R8026
R8024
C41
R8023
R8038
D8005
R8002
CP8001
D8004
R8001
J8001
C7329
IC7301
W877
W867
C8008
C8045
W851
C5901
C5920
C5904
C5908
C5918
C5916
R5918
C5919
W831
R5916
R5928
R5920
B5902
C5902
R5906
C5903
IC5901
CP5901
C5912
C5911
C5910
R5919
L5901
L5902
L5903
L5904
C5914
C5913
N
IC5902
C5924
R5921
R5901
C5922
C5923
C8029
Q8001
R8005
R8009
C8002
W801
W887
W886
W885
W888
W889
W890
IC8006
IC8007
IC8008
J7301
R4053
R4057
W899
C4122
W879
W878
W842
R40
B8001
W841
R8008
R8007
B5903
W897
W898
DVD MT PCB ASSY
A
SIDE A
ACP503
E
CP7301
CP8102
E
CP8001
IC4004
IC4005
IC4003
Q2302
Q2304
Q2303
Q2305
Q2307 Q2306
Q2301
IC4006
Q8013
Q8010
Q8019
Q8018
Q8014
IC4002
IC2301
IC8003
IC7301
Q8005
Q4001
IC5901
Q7302
IC4001
IC8003
IC8008
IC8005
IC8007
IC8004
IC8006
IC5902
DV-696AV-S 43
5678
5678
C
D
F
A
B
E
DMF074A
165
129
193
C4060
C4053
C4063
C4061
C4050
5
3
044
4042
41 C4040
C4039
C4037
C4036
C4034
C4033
C4032
C4031
C4029
C4028
C4027
C4026
7
C8025
R4054
R4052
R4048
R4050
R4047
R4046
R4043
R4040
R4038
R4025
R4027
R4020
4069
4068
R4067
6
X4001
CP4002
C4052
C4005
C4007
C4013
C4019
C4020
C4012
C4021
C4024
C4025
C4030
C4062
C4064
C4073
C4066
C4074
C4084
C4082
C4088
C4022
C4077
C4078
C4076
C4079
C4014
C4017
C4016
C4015
R4015
R4018 R4019
R4002
R4006
R4008 R4051
R4071
R4070
R4082
R4035
R4017
R4061
R4062
R4087
R4084
NR4001
NR4002
IC4004
IC4002
IC4005
IC4003
CP2303
C2306
C2312
C2307
C2313
R2328
R2330
C2319
R2326
R2327
R2310
R2311R2313
R2312
R2316
R2317
R2318
R2325
R4016
C4008
C4009
R4003
C4002
C4003
C4001
R2338
R2332
R2333
R2334
C2310
R2335
C2311
C2309
C2308
Q2302
Q2304
Q2303
Q2305
R2320
R2322
R2323
R2321
Q2307Q2306
R2306
R2307
Q2301
R2309
R2308
C4103
C2303 C2301
C2302
C4104
CP4003
IC4006
W832
C4095
C4094
C4096
R4013
R4011
R4012
C4100
C4098
C4099
W822
B4001
C4056
C4093
B4002
C4087
C2305
C2323
R2329
R2319
R2331
R2342
C2322
W807
R4005
C4105
W825
W826
W804
C4046
1
C7312
R4083
C4023
CP2302
R2337
C2320
C2321
C4114
C4112
NR4005 NR4006
IC5902
C5924
R5921
R5901
C5922
C5923
R8005
R8009
W821 IC2301
CP2301
IC4001
R4053
R4057
C4081
C4091
B4010
C4122
R4030
W864
W865
W841
W820
SIDE A
A
CP502
E
CP4003
CP601
B
CP4002
CP2303
DVD MECHA ASSY
DVD MECHA ASSY
CP2302
DVD MECHA ASSY
CP2301
DV-696AV-S
44
1234
1234
C
D
F
A
B
E
DMF074A
C4071
C4069
C4072
C4068
C4117
C4110
C4051
C4080
C4055
R4058
R4014
R4004
R4022
R4032
C4054
R4060
R4028
C2314
C4086
W846
C4119
R4007
W806
W805
SIDE B
A
DVD MT PCB ASSY
A
CP4002
CP2303
CP2302
CP2301
DV-696AV-S 45
5678
5678
C
D
F
A
B
E
R8092
R8072
B7305
Q8015
R8074
C8053
R8068
R8045
R8046
C8009
C8059
R8050
R8053
C8049
R8036
R8037
C8010 C8007
R8093 R8076
R8069
Q8017
R8077C8056
R8048
R8030
R8031
R8052
R8003
D8006
C8044
R8055
R8058
C8057
C8052
R8054
C8005
R8087
R8096
Q8021
R8075
R8059
R8061
C8006
R8066
C8055
R8064
R8063
C8054
C5915
C5917
C5905
W829
W881
C4071
C4117
C4067
C5921
R4058
C8030
C8051
R8011
Q8020
C4035
R4022
R8012
Q8008
R4032
R4028
R7304
W830
R8043
R8042
C8046
C8062
R8099
W866
C4086
W891
W892
C4119
C5925
R5923
R5922
R8006
B5905
W806
W805
SIDE B
A
CP7301 CP8001
CP4003
DV-696AV-S
46
1234
1234
C
D
F
A
B
E
4.3 OPERATION, OPERATION 2 and OPERATION 3, 4 PCB ASSYS
SW656 SW655
SW654
SW657
SW653
SW652
SW659
SW658
SW661
W001
CP601
W004
W008
W009
D651
SW662
SW664 CP604
D660
R664
W809
DEF085A
DEF095A
SIDE A OPERATION 2 PCB ASSY
C
OPERATION 4 PCB ASSY
H
OPERATION PCB ASSY
B
CP605
G
CP604
CB H
DV-696AV-S 47
5678
5678
C
D
F
A
B
E
SW666
CP602
V651
D659
D658
D657
D656
OS651
D655
D654
D652
C674
CP601
W003
W004
W006
W008
W009
W010
SW663
SW665
SW660
SW667
CP603
CP604
W804
CP605
W012
W013
W002 W805
R666
W808
W807
C653
A
A
DEF086A
DEF084A
D668
D667
SIDE A
Y
OPERATION 3 PCB ASSY
G
CB G
CP4002
A
CP601
CP604
C
CP605
CP603
CP602
DV-696AV-S
48
1234
1234
C
D
F
A
B
E
23
34
1
12
IC651
R651
R652
R653
R654
R655 R656
R657
R658
R662
C675
C676
C651
DEF086A
DEF084A
SIDE B OPERATION 2 PCB ASSY
C
OPERATION 3 PCB ASSY
G
OPERATION PCB ASSY
B
CP603
CP
CP602
CP605
CB G
DV-696AV-S 49
5678
5678
C
D
F
A
B
E
C675
C658
C605
C604
C668
DEF085A
DEF095A
4
A
SIDE B
OPERATION 4 PCB ASSY
H
CB H
CP604CP603
CP601
DV-696AV-S
50
1234
1234
C
D
F
A
B
E
4.4 POWER PCB ASSY
DPF010A
RISK OF FIRE
-REPLACE AS MARKED.
C502_1
FH502_1
FH501_1 F501_1
D503
D506
D502
D505 B501
C8113
C8114
W035
L501
C511
IC502
C509
D508
R507
IC504
IC501
C517
C540
R513
R514
W003
R511
D510
D512
D522
D520
D516
D528
D521
R517
C519
D523
W006
R530
R534
Q504
R540
C538
L505
L503
C536
W012
W005
R529 R528
W016
D531
W032
W031
W030
T501
C531
R505
R527
C535
W018
W019
R502
R542
W013
D511
D513
D519
Q510
C505
C506
D533
IC503
D515
R539 C520
D525
W015
C523
D532
W814
D534
R546
C518
C513
R510_1
C516
R524
D517
W027
W026 W029
C522
C515_1
D535
C514
C521
C527
D536
C528
C526
W037
W804
CP502
W803
W036
W001
W024
W004
W002
W008
W007
W010
W023
W021
W025
W038
W011
R503
R512_1
D527
Q502
Q515
W817
C8118
OS8101
CP8102
J8102
C8104
W022
W028
CP503_1
R8118
R8119
D509_1
R8103
C8112
R8105
W026
POWER PCB ASSY
F
F
SIDE A
CP4003
A
CP502
IC504
IC502 Q510
IC503 Q515 IC501 Q504
Q502
CP7301
A
CP503
J501
AC IN
J501
DV-696AV-S 51
5678
5678
C
D
F
A
B
E
DPF010A
R8111
R8112
R8110
C508
R504
R515
C503
R518
R516
Q501
R523
Q506
R538
R506
Q512
Q503
Q511
Q509
R541
R543
R509
Q505
Q513
R544
R537
R536
R531
C507
C541
C501
R545
R526
R519
R547
R525
R548
C8120
B8101
R8106
R8124
R8122 R8121
C8119
R8123
R8107
Q8103
C8103
C8109
C8110
C8108
POWER PCB ASSY
F
F
SIDE B
CP502
Q512 Q503
Q513
Q501 Q506Q511 Q509
Q505 Q8104
Q8105 Q8102Q8101
CP503
DV-696AV-S
52
1234
1234
C
D
F
A
B
E
5. PCB PARTS LIST
Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List.
The mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
When ordering resistors, first convert resistance values into code form as shown in the following examples.
Ex.1 When there are 2 effective digits (any digit apart from 0), such as 560 ohm and 47k ohm (tolerance is shown by J=5%,
and K=10%).
Ex.2 When there are 3 effective digits (such as in high precision metal film resistors).
561
473
R50
1R0
5621
NOTES:
560 Ω
47k Ω
0.5 Ω
1 Ω
RD1/4PU J
RD1/4PU J
RN2H K
RS1P K
56 x 10
1
47 x 10
3
R50
1R0
561
473
5.62k Ω
RN1/4PC F562 x 10
1
5621
Mark No. Description Part No.
LIST OF ASSEMBLIES
1..DVD MT PCB ASSY A2J009A130
( : DXZTRA, RLFXZT_Only)
1..DVD MT PCB ASSY A2I012A130
( : RPWXZT, RTXZT_Only)
1..OPERATION PCB ASSY A2I813A270
1..OPERATION PCB ASSY A2I812A270
( : RTXZT_Only)
1..OPERATION 2 PCB ASSY A2I802A280
1..OPERATION 3 PCB ASSY A2I903ADF0
1..OPERATION 4 PCB ASSY A2I903ADG0
>
1..POWER PCB ASSY A2J012A240
1..DVD MECHA ASSY A2I802A650
NSP 2..LOADING MOTOR PCB ASSY A2F101A610
NSP 2..SW PCB ASSY A2F101A640
Mark No. Description Part No.
A DVD MT PCB ASSY
SEMICONDUCTORS
IC2301 IC LA6565VR-TLM-E I03FV65650
IC4002 IC MT1389EXE/B2-L IC8K0389BX
IC4001 IC BR24L08FJ-WE2 I57F04L080
IC4003 IC BD5229G-TR I97F052290
IC4004 IC S29AL016D70TFI020 S2J003AF03
IC4005 IC EM638165TS-7G IG2J081657
IC4006 IC LM1117S-ADJ I1TF911170
IC5901 IC MT1392E/C-L IC8K013920
IC5902 IC PQ1K503M2ZPH I0GF9K5030
IC7301 IC LA73054-TLM I03FG30540
IC7302 IC SN74CBT3257PWR I5CJ032570
IC8001 IC TC7SHU04FU I55F004FU0
IC8003 IC PCM1742KEQ/2K I17F02KEG0
IC8007 IC RC4580IDR I04J045800
OTHERS
J8001 RCA JACK 060R451009
J7301 RCA JACK 063R700013
J7302 RCA JACK 060R451010
CP5901 CONNECTOR 0694YJ3018
X4001 CRYSTAL (27MHz) 100GT02720
J8002 RCA JACK 060R451011
B OPERATION PCB ASSY
SEMICONDUCTORS
IC651 IC PT6315 IF4K063150
SWITCHES AND RELAYS
SW652 - SW659 SWITCH TACT 0504R01T38
SW661, SW666 SWITCH TACT 0504R01T38
OTHERS
V651 TUBE FLUORESCENT 096F82R601
V651 TUBE FLUORESCENT 096782R603
OS651 REMOTE RECEIVER 077A040001
C OPERATION 2 PCB ASSY
SWITCHES AND RELAYS
SW660-SW665 SWITCH TACT 0504R01T38
F POWER PCB ASSY
RESISTORS
>R511 R,FUSE 68 OHM 1/4W R65584680J
OTHERS
CP8102 CORD, CONNECTOR 06CU223002
J8102 RCA, JACK 060R401122
OS8101 OPTICAL, DEVICE 07AA000011
G OPERATION 3 PCB ASSY
SWITCHES AND RELAYS
SW667 SWITCH TACT 0504R01T38
H OPERATION 4 PCB ASSY
There is no Service Parts
D SW PCB ASSY
There is no Service Parts
E LOADING MOTOR PCB ASSY
There is no Service Parts
Mark No. Description Part No.
DV-696AV-S 53
5678
5678
C
D
F
A
B
E
6. ADJUSTMENT
6.1 WHEN REPLACING DVD DECK
Before removing Pick Up PCB and DVD PCB connector, short circuit the position shown in Fig. 1 using
a soldering iron. If you remove the DVD Deck with no soldering, the Laser may be damaged.
WHEN REPLACING DVD DECK
[ Removing the DVD Deck ]
[ Installing the DVD Deck ]
Remove all the soldering on the short circuit position after the connection of Pick Up PCB and DVD
PCB connector.
NOTE
Fig. 1
Before your operation, please read “PREPARATION OF SERVICING” .
Use the Lead Free solder.
Manual soldering conditions
• Soldering temperature: 320 ± 20˚C
• Soldering time: Within 3 seconds
• Soldering combination: Sn-3.0Ag-0.5Cu
When Soldering/Removing of solder, use the draw in equipment over the Pick Up Unit to prevent the
Flux smoke from it.
•
•
•
•
Short circuit using a
soldering iron.
Pick Up PCB
DV-696AV-S
54
1234
1234
C
D
F
A
B
E
6.2 TEST MODE
POWER ON
DSC - &&&
GGF1381
Test mode
remote control
unit
GGF1381
Test mode
remote control
unit
<TRAY OPEN> <TRAY CLOSE>
OPEN/CLOSE
(Player)
OPEN/CLOSE
Press the play key
( ) of the normal
remote control unit.
(Player)
TEST MODE: PLAY
TEST MODE: OFF
An address is displayed
OR
ESC
<PLAY> ESC TEST
CHECK
DVD, CD
DVD disc
POWER
ON
OFF
POWER
DISC SET
Notes:
• After going into test mode, if you play back the disc, "DISC-NON" is displayed.
• The video signal and the audio signal are outputted during the test mode.
• The SKIP key and the SCAN key are effective during the test mode.
DV-696AV-S 55
5678
5678
C
D
F
A
B
E
6.3 TEST MODE IN
Test Mode Functional Specification
1 Test mode entry
In the power ON state, press the [ESC] (A8-5F) key and [TEST / RANDOM] (A8-5E) key in order of the Test mode remote control
unit.
• Light the all FL and LEDs.
• OSD displays test mode.
Note:
* When pressing the keys of something, the FL displays "NO DISC" and the LED lighting disappears.
2 Release the Test mode
• Turn off the power.
• Press the [ESC] (A8-5F) key of the remote control unit.
3 LD ON
DVD : Press the [TEST] (A8-5E) and [1] (A8-01) keys in order, and turn on the laser diode (650 nm).
CD : Press the [TEST] (A8-5E) and [4] (A8-04) keys in order, and turn on the laser diode (780 nm).
DV-696AV-S
56
1234
1234
C
D
F
A
B
E
6.4 DISC REMOVAL METHOD
1.
2.
3.
Remove the Top Cabinet and Front Cabinet. (Refer to item 1 of the DISASSEMBLY INSTRUCTIONS.)
Rotate the Main Gear in the direction of the arrow by hand.
(Refer to Fig. 1, Fig.2)
Draw the Tray.
DISC REMOVAL METHOD AT NO POWER SUPPLY
Fig. 1
DVD DeckMain Gear
The laser diode used for a pickup head may be destroyed with external static electricity.
Moreover, even if it is operating normally after repair, when static electricity discharge is
received at the time of repair, the life of the product may be shortened.
Please perform the following measure against static electricity, be careful of destruction of a
laser diode at the time of repair.
• Place the unit on a workstation equipped to protect against static electricity, such as
conductive mat.
• Soldering iron with ground wire or ceramic type is used.
• A worker needs to use a ground conductive wrist strap for body.
PREPARATION OF SERVICING
Fig. 2
Rack Loading (White)
DVD Player (Bottom Side)
DV-696AV-S 57
5678
5678
C
D
F
A
B
E
7. GENERAL INFORMATION
7.1 DIAGNOSIS
7.1.1 DISPLAY SPECIFICATION OF THE TEST MODE
Character in bold : Item name
: Information display
1
5
6
10
11
8
9
3
2
12
15
13
14
1 Address indication
The address being traced is displayed in number.
(as for the DVD, indication of decimal number is possible.)
DVD : ID indication (hexadecimal number, 8 digits)
[∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗]
CD : ID indication [∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗]
2 Code indication of remote control unit [R – ∗ ∗ ∗ ∗]
In case of double code, display a 2nd code.
3 Main unit keycode indication [K – ∗ ∗]
5 Tracking status [TRKG – ∗ ∗ ∗]
Tracking on : [ON]
Tracking off : [OFF]
6 Spindle status [SPDL – ∗ ∗ ∗]
[OFF], [CLV]
7 Mechanism (loading) position value [M – ∗ ∗]
Unknown : [01] or [41]
Open state : [04]
Close state : [08]
During opening : [12]
During closing : [22]
8 Slider position [S – ∗ ∗ ∗ ∗]
In Side Switch ON : [01]
In Side Switch OFF : [00]
9 Output video system [V – ∗ ∗ ∗ ∗]
NTSC system : [NTSC]
PAL system : [PAL]
Automatic setting : [AUTO]
Scart terminal output [SK – ∗ ∗]
(Display only the WY model which can do the output setting
of scart terminal.)
VIDEO : [00]
S-VIDEO : [01]
RGB : [02]
0 Disc sensing [DSC – ∗ ∗ ∗]
The type of discs loaded is displayed.
[DVD], [CD ], [VCD], [ ]
- Jitter value [J – ∗ ∗ ∗ ∗] Note:Don’t use it.
= Version of the FL controller [FL: ∗ ∗ ∗ ∗]
~ Region setting of the player [REG: ∗]
Setting value : [1] to [6]
! Destination setting of the FL controller
[MDL: ∗ ∗ ∗ ∗ / ∗ ∗ ∗]
Four characters in the front represent code 01.
Three characters in the back represent the destination code.
J: /J, K: /KU, /KC, /KU/KC, R: /RL/RD, RAM : /RAM,
LB: /LB, WY: /WY
@ Version of the flash ROM [VERSION: ∗∗∗∗∗∗∗∗]
7
DV-696AV-S
58
1234
1234
C
D
F
A
B
E
7.1.2 FUNCTIONAL SPECIFICATION OF THE SHORTCUT KEY
• Service mode indication (ESC + CHP/TIM keys)
ID Address
The error rate is always displayed in exponential notation, e.g., ∗.∗ ∗ e - ∗, for both DVDs and CDs.
EDC/ID/AV 1 error history (ID Address, EDC/ID Error, last eight errors)
• Calculation of the average error rate (ESC + "5" [Test mode remote control unit] keys)
The average of the last eight error rates is calculated and indicated in exponential notation. After the calculation is completed, "OK" or "NG" is
displayed. If "NG" is displayed, the disc tray will open (for both DVDs and CDs)
For DVDs: OK with 5.0e-4 or less, for CDs: OK with 7.6e-3 or less
• Indication of model information (ESC + CHAP keys)
The items from 12 to 15 of the TEST MODE Indications are displayed. However, in the indications, S in the standard test mode is changed to
CHIP VERSION, and M is changed to FL VERSION. For details, see 7.1.3.
• Region confirmation mode (ESC + A.MON [Test mode remote control unit] + "1"-"8" [Test mode remote control unit] keys)
After you press the A.MON key while holding the ESC key pressed and then input the region number, if the number is different from that set in
the unit, an error message is displayed, and the tray opens.
Command Contents Conditions Remote Control
Key Name Remote
Control Code
Memory clear and region / revision indication CLEAR (∗1) A8-45
Average value measurement of DVD error rate 5 (∗1) A8-05
CD error rate measurement 5 (∗1) A8-05
Scart terminal output : VIDEO
WY, models equipped with Scart terminal
AUDIO AF-BE
Scart terminal output : S-VIDEO SUBTITLE AF-36
Scart terminal output : RGB ANGLE AF-B5
Progressive OFF Only for progressive models R_SKIP A3-9D
Progressive ON F_SKIP A3-9C
ZOOM ON (X2 -> X4 -> x1) ZOOM AF-37
Service mode indication (error rate indication, etc.) CHP/TIM (∗1) A8-13
Model information indication CHAP (∗1) A8-40
Title search Input mode IN
Title No. input
Search execution
SIDE A (∗1)
Numbers (∗1)
PLAY (∗1)
A8-4D
A8-00 to A8-09
A8-17
Region confimation mode A.MON (∗1)
Numbers (∗1) A8-1E
A8-01 to A8-08
Only during normal playback, the following shortcut keys can be assigned by pressing a required key after pressing the ESC
key of the remote control unit. To quit, press the ESC key
∗1 : Test mode remote control unit
DV-696AV-S 59
5678
5678
C
D
F
A
B
E
7.1.3 SPECIFICATION OF MODEL INFORMATION DISPLAY
• Display contents
Character in bold : Item name
: Information display
1
3
2
5
6
1 Destination indication
Display it according to model information set from the FL Driver IC.
2 Region No.
3 ROM number
4 REG CHK
5 SUM CHK
6 CHIP VERSION
To display model information : Press the ESC key then the CHAP key.
To close the model information display : Press the ESC key.
AREA : WY REGION : 2
ROM NUMBER YAD5215B
REG CHK 40
SUM CHK D2AD
FL VERSION 1.08
CHIP VERSION 1389FE
Don't Care
Don't Care
DV-696AV-S
60
1234
1234
C
D
F
A
B
E
7.1.4 FUNCTIONAL SPECIFICATION OF THE SERVICE MODE
• Display during Service Mode
To enter Service Mode, press the CHP/TIM key while holding the ESC key pressed.
To quit, press the ESC key.
Service mode display
1 ID Address
2 Error rate (always displayed), in exponential notation
ERROR RATE : ∗ ∗ ∗ ∗ ∗ ∗ ∗
( ∗ ∗ ∗ ∗ )
• Calculation of the average error rate
For DVDs: OK with 5.0e-4 or less, for CDs: OK with 7.6e-3 or less
3 EDC/ID error history (ID Address, EDC/ID errors, last eight errors)
Note:
∗ Error of AV1 is not supported in this player.
Number of error
Indication plan contents
Character in bold : Item name
: Information display
1
2
3
ex) For DVDs
• Step 1
%%e -&
%%e -6 : OK
%%e -5 : OK
%%e -4 : Refer to Step 2
%%e -3 : NG
%%e -2 : NG
• Step 2
%%e -4
3.0e -4 : OK
4.0e -4 : OK
5.0e -4 : OK
6.0e -4 : NG
7.0e -4 : NG
DV-696AV-S 61
5678
5678
C
D
F
A
B
E
7.1.5 METHOD FOR DIAGNOSING DEGRADATION OF THE LDS ON THE PICKUP ASSY
CP2303
CP2301
C
R2326
R2327
R2310
R2311R2313
R2312
R2316R2317
R2318
R2325
C4002
C4003
R2338
R2332
R2333
R2334 C2310
R2335
C2311
C2308
Q2302
Q2304
Q2303
Q2305
R2320
R2322
R2323
R2321
Q2307Q2306
R2306
R2307
Q2301
R2309
R2308
2
303 C2301
C2305
W819 R2337
C2320
W817
W809
To OPTICAL PICK
U
CP2301
CP2303
Case when this diagnosis is required :
When playback of any disc, including a test disc (DVD: GGV1025, CD: STD-905), cannot be performed
How to diagnose
In the case mentioned above, degradation of the laser diodes (LDs) mounted on the PICKUP Assy is suspected.
Measure the voltage between the two ends of one of the resistors mentioned below.
Measure the voltage between the two ends of R2321 or R2323 on the DVD MT
PCB Assy. If the voltage is 0.4 V or higher, the 650-nm LD is degraded.
No playback of a DVD :
Measure the voltage between the two ends of R2320 or R2322 on the DVD MT
PCB Assy. If the voltage is 0.4 V or higher, the 780-nm LD is degraded.
No playback of a CD :
If the measurements show degradation
of an LD, replace the PICKUP Assy.
SIDE A
Front side
DVD MT PCB ASSY
A
DV-696AV-S
62
1234
1234
C
D
F
A
B
E
7.1.6 TROUBLE SHOOTING
No. Symptoms Diagnosis Contents Possible Defective Points
1 The power is not turned on. Check the voltage of AT+3.3 V, –28 V and FLDC on the POWER
SUPPLY Unit. POWER PCB ASSY
Are wires of output connector (POWER PCB ASSY) and CP4003
(DVDM Assy) disconnected or damaged ? Connector / cable
Check that the voltage at IC651-pin 10 (K 1) on the FLKY Assy
becomes about 2.7 V when the POWER key is pressed and 0 V when
it is released.
OPERATION 2 Assy
Tact SW
(when operation of only the
POWER key on the main unit is
not accepted)
Check that the voltage at OS651-pin 1 (IR) on the OPERATION1 Assy
is in the range between 0 and 3.3 V while receiving signals from the
remote control unit when any key on it is pressed.
OPERATION Assy
Remote receiver section
(when operation of only the
POWER key on the remote
control unit is not accepted)
2 An opening screen is not
displayed on the monitor
(The FL display lights. The
mechanism does not work.)
• Check the voltage of E+6.8 V and SW+3.3 V on the POWER PCB
ASSY.
• Check the voltage of P.ON-H is about 2.8 V on the POWER PCB
ASSY. POWER PCB Assy
Check that the following voltage are output :
IC4006-pin 5 : 1.8 V, on the DVD MT PCB Assy.
DVD MT PCB Assy
1.8 V Regulator IC (IC4006)
Is a resonator (X4001 : 27 MHz) on the DVD MT Assy oscillating ? DVD MT PCB Assy
Crystal resonator (X4001)
• Are the signals input into IC4005-pin 16 (DWE#), pin 19 (DCS#)
and pin 38 (SDCLK) on the DVD MT Assy ?
(Is a signal fluctuating ?)
→ Communication with SDRAM DVD MT PCB Assy
DVD IC (IC4002)
Flash ROM (IC4004)
SDRAM (IC4005)
Is a signal output from IC4004-pin 28 (PRD#) on the DVD MT Assy?
(Is a signal fluctuating for several hundred mS after the power is turned
on ?)
DVD MT PCB Assy
Flash ROM (IC4004)
Are the signals of IC4003-pin 5(SDA) and pin 6(SCL) on the DVD MT
Assy fluctuating for one or two seconds after the power is turned ? DVD MT PCB Assy
EEPROM (IC4001)
3An opening screen is not
displayed on the monitor
(The FL display lights. The
mechanism does not work.)
Check the video signal path between DVD IC (DVD MT Assy IC4002)
and video-out terminal (see the block diagram)
DVD MT PCB Assy
Video circuit after DVD IC
(IC4002)
DV-696AV-S 63
5678
5678
C
D
F
A
B
E
No. Symptoms Diagnosis Contents Possible Defective Points
4A tray cannot be opened.
(An opening screen is
displayed on the monitor)
Does the voltage of CP2302-pin 3 and pin 1 on the DVD MT Assy
change normally ?
Pin 5 (SW2(TRIN)): Tray is fully closed: "L"
Pin 3 (SW1(TROUT)): Tray is fully opened: "L"
Tray SW
Is a LOAD-DRV signal reaching ? DVD MT PCB Assy
DVD IC (IC4002)
Are the signals output from IC2301-pin 5 and pin 6 (CP2302-pin 4 and
pin 5) on the DVD MT Assy ?
Pin 5: Approx. 4.5 V during opening tray approx. 0 V during closing tray.
Pin 4: Approx. 0 V during opening tray approx. 4.5 V during closing tray.
DVD MT PCB Assy
FTS Driver IC (IC2301)
Are wires of CP2302 and CP2303 on the DVD MT Assy disconnected
or damaged ? Connector / cable
Does the voltage of CP2303-pin 5 change by pressing the Inside
switch. Inside switch
5 Playback impossible
(no focusing)
Are the signals output from IC2301-pin 9 (F+) and pin 8 (F–) on the
DVD MT Assy ? DVD MT PCB Assy
FTS Driver IC (IC2301)
Does 650-nm LD emit light ?
Does a pickup lens move up / down ?
Does an actuator spring bend ? Pickup
Are plastic parts damaged ? Or is a shaft detached ?
Is the turntable detached or tilted ? Mechanism section (motor)
Is flexible cable of CP2301 on the DVD MT Assy disconnected or
damaged ? Flexible cable / connector
Is signal output from IC4002-pin 42 (FOSO) on the DVD MT Assy ?
(Device control of about 1.4 V is output usually. It is fluctuated by about
± 250 mV with focus up / down.)
DVD MT PCB Assy
DVD IC (IC4002)
6 Playback impossible
(Spindle does not turn)
Are the signals output from IC2301-pin 13 (MOT SPDL–), and pin 14
(MOT SPDL+) on the DVD MT Assy ?
Is pin 41, 42 (STBY) fixed LOW?
DVD MT PCB Assy
FTS Driver IC (IC2301)
Is there any part detached from the spindle motor ?
Or Is there any foreign object lodged in it ? Mechanism section
(Spindle motor)
Are wires of CP2303 on the DVD MT Assy disconnected or damaged ? Flexible cable / connector
Is signal output from IC4002-pin 37 (DMSO) on the DVD MT Assy ? DVD MT PCB Assy
DVD IC (IC4002)
7 Playback impossible
(Playback stops)
Does 650-nm LD deteriorate ?
If the voltage at each both ends of R2321 and R2323 on the DVD MT
Assy is 0.4 V or more, the 650-nm LD is definitely deteriorated.
650-nm LD deteriorated.
(When playback of a DVD is
impossible)
Does 780-nm LD deteriorate ?
If the voltage at each both ends of R2320 and R2322 on the DVD MT
Assy is 0.4 V or more, the 780-nm LD is definitely deteriorated.
780-nm LD deteriorated.
(When playback of a CD is
impossible)
Are there scratches or dirt on the disc ? Disc
8 Picture disturbance during
playback
(block noise, freeze, other)
Are there scratches or dirt on the disc ?
Is there a problem with the format of the disc ? Disc
9 No sound
(Picture is normal) Is signal output from IC8003, 8004, 8005-pin 7 and pin 8 on the DVD
MT Assy ? DVD MT PCB Assy
Audio DAC IC (IC8003, 8004,
8005)
DV-696AV-S
64
1234
1234
C
D
F
A
B
E
Symptoms That May Occur When Any Of The Following ICs Is In Failure
IC Symptoms
EEP ROM
(DVD MT PCB Assy : IC4001) User's data cannot be stored in memory.
The ID number is lost.
16M Flash ROM
(DVD MT PCB Assy : IC4004) The power cannot be turned on.
Downloading of the firmware cannot be performed.
DVD IC
(DVD MT PCB Assy : IC4002) Any kind of symptoms (no power, a failure in any of the servo, video and audio systems, etc.) may be
generated, because the DVD processing is performed by a single chip.
64M SDRAM
(DVD MT PCB Assy : IC4005) No power.
Block noise is generated during playback.
DV-696AV-S 65
5678
5678
C
D
F
A
B
E
7.2 DISASSEMBLY
REMOVAL OF MECHANICAL PARTS AND P.C. BOARDS
.
1.
2.
3.
4.
Short circuit the position shown in Fig. 1-3 using a
soldering iron. If you remove the DVD Deck with no
soldering, the Laser may be damaged.
Disconnect the following connectors:
(CP2301, CP2302, CP2303).
Remove the 4 screws 1.
Remove the DVD Deck in the direction of arrow.
1-3: DVD DECK (Refer to Fig. 1-3)
NOTE
Before your operation, please read “PREPARATION
OF SERVICING”.
Use the Lead Free solder.
Manual soldering conditions
• Soldering temperature: 320 ± 20 ˚C
• Soldering time: Within 3 seconds
• Soldering combination: Sn-3.0Ag-0.5Cu
When Soldering/Removing of solder, use the drawing
equipment over the Pick Up Unit to prevent the Flux
smoke from it.
When installing the DVD Deck, remove all the soldering
on the short circuit position after the connection of Pick
Up PCB and DVD PCB connector.
1.
2.
3.
4.
5.
1-4: DVD PCB (Refer to Fig. 1-4)
.
1-1:
1.
2.
3.
4.
5.
6.
8.
Remove the 5 screws 1.
Remove the Top Cabinet in the direction of arrow (A).
Disconnect the following connector: (CP4002).
Unlock the 4 supports 2.
Remove the Front Cabinet in the direction of arrow (B).
Remove the 10 screws 3.
7. Remove the 2 screws 4.
Remove the Operation 1/2/3 PCB in the direction of
arrow(C).
TOP CABINET/FRONT CABINET/OPERATION
1/2/3/4 PCB (Refer to Fig. 1-1)
Power PCB
Fig. 1-2
Fig. 1-3
Short circuit using a
soldering iron.
Fig. 1-4
DVD MT PCB
2
2
2
2
111
111
3
2
3
3
3
1
Front Cabinet
Operation PCB Fig. 1-1
Top Cabinet
1-2: POWER PCB (Refer to Fig. 1-2)
1.
2.
3.
4.
Disconnect the following connectors:
(CP502, CP503, CP8001).
Remove the 3 screw 1.
Remove the 4 screws
Remove the Power PCB in the direction of arrow
2.
1.
2.
4.
Remove the 5 screws 1.
Remove the screws 2.
3. Remove the 4 screws 3.
Remove the DVD PCB in the direction of arrow
2
2
1
1
1
1
1
(A)
(B)
Operation 3 PCB
Operation 4 PCB
Operation 2 PCB
(C)
(C)
(C)
(C)
2
2
3433
3
3
3
3
3
34
3
DVD Deck
1
1
1
1
Pick Up PCB
DV-696AV-S
66
1234
1234
C
D
F
A
B
E
7.3 DVD DECK SECTION
REMOVAL OF DVD DECK PARTS
2-1: TRAY (Refer to Fig. 2-1-A)
Set the Tray opened. (Refer to the DISC REMOVAL
METHOD AT NO POWER SUPPLY)
Unlock the 2 supports 1 and draw it while sagging the
Tray.
1.
2.
Fig. 2-1-A
Tray
Loader Ass'y
NOTE
1. In case of the Tray installation, install them as the circled
section of Fig. 2-1-B so that the each markers are met.
2-2: TRAVERSE ASS'Y (Refer to Fig. 2-2-A)
Remove the screw 1.
Unlock the 2 supports 2.
Remove the Insulator (R) from the Loader Sub Ass'y.
Remove the Traverse Ass'y.
1.
2.
3.
4.
Fig. 2-2-A
Tray
Loader Ass'y
Fig. 2-1-B
Insulator (R)
NOTE
1. Do not disassemble the DVD DECK PARTS except
listed parts here. Minute adjustments are needed if the
disassemble is done. If the repair is needed except
listed parts, replace the DVD MECHA ASS'Y.
NOTE
1.
2.
In case of the Traverse Ass'y, install it from 1 to 4 in
order. (Refer to Fig. 2-2-B)
In case of the Traverse Ass'y installation, hook the wire
on the Loader Ass'y as shown Fig. 2-2-C.
1
Traverse Ass'y
Loader Sub Ass'y
Fig. 2-2-B
Check Lock
Traverse Ass'y
Rack Loading
Loader Ass'y (Bottom Side)
Holder Traverse
Fig. 2-2-C
Loader Ass'y
Check Hook
Loading Belt
Gear Pulley
1
2-3: LOADING MOTOR PCB ASS'Y/ LOADING BELT
(Refer to Fig. 2-3-A)
1.
2.
3.
4.
5.
6.
Remove the Loading Belt.
Remove the screw 1.
Remove the Loading Motor PCB Ass'y.
Remove the 2 screws 2.
Remove the Loading Motor.
Remove the Gear Pulley.
Fig. 2-3-A
Loading Motor PCB Ass’y
• Screw Torque: 2.0 ± 0.3 kgf•cm
• Screw Torque: 2.5 ± 0.3 kgf•cm (Screw1)
• Screw Torque: 1.0 ± 0.3 kgf•cm (Screw2)
2
2
Loading Motor
1
1
2
2
Push to Sag
Push to Sag
1
2
4
3
3
33
4
DV-696AV-S 67
5678
5678
C
D
F
A
B
E
BROWN (1)
WHITE (2)
NOTE
1.
2.
3.
4.
In case of the Pulley Motor installation, check if the value
of the Fig. 2-3-B is correct.
When installing the wire of the Loading Motor PCB Ass'y,
install it correctly as Fig. 2-3-C.
Manual soldering conditions
• Soldering temperature: 320 ± 5 ˚C
• Soldering time: Within 4 seconds
• Soldering combination: Sn-3.0Ag-0.5Cu
When installing the Loading Motor PCB Ass'y, install it
correctly as Fig. 2-3-D.
In case of the Loading Motor PCB Ass'y installation, hook
the wire on the Loader Sub Ass'y as shown Fig. 2-3-E.
Fig. 2-3-B
7.0 ± 0.1 mm
Safety surface for pressing
of the insert.
Loading Motor
Pulley Motor
Check Hook
Loading Motor PCB Ass’y
Loading Motor PCB Ass’y Fig. 2-3-C
Fig. 2-3-E
Check Hook
Fig. 2-3-D
Rack Loading
AB
The Lever should be position
between A and B.
Check Hook
Rack Loading
2
Loader Sub Ass’y
Gear Main
2-4: RACK LOADING/MAIN GEAR/PULLEY GEAR
(Refer to Fig. 2-4-A)
1.
2.
3.
Unlock the support 1 and remove the Gear Pulley.
Remove the Gear Main.
Press down the catcher 2 and slide the Rack Loading.
Gear Pulley
1Fig. 2-4-A
NOTE
1.
2.
In case of the Rack Loading installation, hook the Rack
Loading on the Loader Sub Ass'y as shown Fig. 2-4-B.
When installing the Gear Main, take care the direction
of up or down as shown Fig. 2-4-C.
Fig. 2-4-B
Rack Loading
Check Hook
Fig. 2-4-C
Main Gear
Up Side
Down Side
2-5: CLAMPER ASS'Y (Refer to Fig. 2-5-A)
Press the Clamper and rotate the Plate Clamper clockwise,
then unlock the 3 supports 1.
Remove the Plate Clamper, Magnet Clamper and Clamper.
1.
2.
Plate Clamper
Magnet Clamper
Fig. 2-5-A
Main Frame
Clamper
1
1
1
Loader Sub Ass'y (Bottom Side)
DV-696AV-S
68
1234
1234
C
D
F
A
B
E
Holder Traverse
Insulator (F)
Traverse Ass'y
Insulator (F)
Insulator (R)
NOTE
1. In case of the Clamper Ass'y installation, install
correctly as Fig. 2-5-B.
Fig. 2-5-B
Plate Clamper
Clamper
2-6:
Remove the Holder Traverse.
Remove the 2 Insulator (F).
Remove the Insulator (R).
1.
2.
3.
Fig. 2-6-A
HOLDER TRAVERSE/INSULATOR (F)/INSULATOR
(R) (Refer to Fig. 2-6-A)
NOTE
1. In case of the Insulator (F) installation, install correctly
as Fig. 2-6-B.
Fig. 2-6-B
Traverse Holder
Insulator (F)
2-7:
Unlock the support 1.
Remove the Gear Middle.
Remove the screw 2.
Remove the Rack Feed Ass'y.
Remove the screw 3.
Remove the Switch PCB Ass'y.
Remove the screw 4.
Remove the Gear Feed.
Remove the 2 screws 5.
Remove the Feed Motor.
Remove the Gear Motor.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
SWITCH PCB ASS'Y/GEAR MIDDLE/GEAR FEED/RACK
FEED ASS'Y/FEED MOTOR (Refer to Fig. 2-7-A)
3
Gear Middle
Gear Motor
Feed Motor
• Screw Torque: 1.3 ± 0.3 kgf • cm (Screw 2)
• Screw Torque: 3.0 ± 0.3 kgf • cm (Screw 3)
• Screw Torque: 1.0 ± 0.3 kgf • cm (Screw 4, 5)
Switch PCB Ass'y
2
4
Rack Feed Ass'y
Gear Feed
5
Fig. 2-7-A
Traverse Ass'y
5
1
NOTE
1.
2.
3.
4.
When installing the Rack Feed Ass'y, push both ends to
align the teeth as shown Fig. 2-7-B. Then install it.
In case of the Gear Motor installation, check if the value
of the Fig. 2-7-C is correct.
When installing the wire of the Switch PCB Ass'y, install
it correctly as Fig. 2-7-D.
Manual soldering conditions
• Soldering temperature: 320 ± 5 ˚C
• Soldering time: Within 4 seconds
• Soldering combination: Sn-3.0Ag-0.5Cu
After the assembly of the Traverse Ass'y, hook the wire
on the Traverse Ass'y as shown Fig. 2-7-E.
[OK] [NG]
Fig. 2-7-B
Rack Feed Ass'y
Push
Push
Fig. 2-7-C
8.0 ± 0.2 mm
Safety surface for pressing
of the insert.
Feed Motor
Gear Motor
Check Lock
Pickup leneses
GEM1004
GED-008
DV-696AV-S 69
5678
5678
C
D
F
A
B
E
[ 24 pin FFC ]
When installing the FFC, fold it correctly and install it as
shown from Fig. 2-8.
2-8: FFC WIRE HANDLING
1.
Do not make the folding lines except the specified
positions for the FFC.
1.
NOTE
Fig. 2-8
Traverse Ass'y
Check Hook
Check Hook
Check Hook
Check Hook
Fig. 2-7-E
~ FEED MOTOR ~
WHITE (4)
BROWN (3)
~ SPINDLE MOTOR ~
YELLOW (2)
GREEN (1)
Fig. 2-7-D
Switch PCB Ass'y
• Install wire from(1) to (4) in order.
To Pick Up PCB
Reinforcement Plat
• Loosen the wirein the direction of the arrows.
Printing _Serface
79 ± 1 mm
DV-696AV-S
70
1234
1234
C
D
F
A
B
E
7.4 IC INFORMATION
IC4002
MT1389EXE/B2-L
MPEG/MICON/RF-AMP
101 102 103 104 105 106107 108 109 110 111 112 113 114 115116 117 118 119 120 121 122 123 124 125 126 127 128
129 130 131 132133134 135 136 137138 139 140 141142 143144 145146 147 148149 150 151152 153 154155 156 157 158 159 160 161162 163 164 165 166 167168 169 170 171 172173 174175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191192
193194195196197198199200201202203204205206207208209210211212213214215216217218219220221222223224225226227228229230231232233234235236237238239240
241242243244245246247248249
250251
252
253254
255256
110
100
111213141516171819 22021222324
2526272829 3
30313233343536373839 4
40414243444546474849 5
50
51525354
55
56575859 6
6061626364
65 66 67 68 69
7
70 71 72 73 74 75 76 77 78 79
8
80 81 82 83 84 85 86 87 88 89
9
90 91 92 93 94 95 96 97 98 99
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
AGND
DVDA
DVDB
DVDC
DVDRF[P
DVDRF[N
MA
MB
MC
DVDD
SB
SC
SD
CDFON
CDFOP
SVDD3
RFLV/RFON
SGND
V2REFO
V20
FEO
TEO
TEZIS[LV
DMO
FMO
PWMOUT1/V_ADIN9
FDO
USB_VDD3
TDI/V_ADIN4 (JTAG)
FG/V_ADIN8 (PU)
TCK/V_ADIN6 (JTAG)
TDO/V_ADIN7 (JTAG)
IOA2 (PU)
IOA3 (PU)
IOA4 (PU)
IOA5 (PU)
IDA7 (PU)
IOA6 (PU)
DVSS
APLLCAP
APLLVSS
IOA19 (PU)
IOA18 (PU)
HIGHA0 (PU)
DVDD18
65
66
67
68
254
253
255
256
APLLVSSVDD3
XIOWR
A16
HIGHA7 (PU)
DVDD3
HIGHA2 (PU)
HIGHA3 (PU)
HIGHA4 (PU)
HIGHA5 (PU)
HIGHA6 (PU)
HIGHA1 (PU)
IOA20
XIOCS (PU)
XIODE
DVDD3
AD0
AD1
AD2
AD3
DVSS (18)
AD4
AD5
AD6
IOA2/V_ADIN0
ALE (PU)
AD7
A17
IOA0 (PU)
DVSS (3)
XUWR (PU)
XURD (PU)
DVDD18
UP1_2 (PU)
UP1_3 (PU)
UP1_4 (PU)
UP1_5 (PU)
UP1_6 (PU)
UP1_7 (PU)
UP3_0 (PU)
UP3_1 (PU)
UP3_4 (PU)
PU3_5 (PU)
DVDD3
ICE (PD)
XPRST (PU)
IR
XINT0 (PU)
DQM0
DQS0
RD7
DVSS (18)
RD6
125
126
127
128
RD5
DVSS (3)
RD4
RD3
DVDD18
RD2
RD1
RD0
RD15
DVDD3
RD14
RD13
RD12
RD11
RD10
RD9
(3) DVSS
DQS1
RD8
DQM1
XCAS
XRAS
DVDD3
XRCS
BA0
(18) DVSS
BA1
RA10
RA0
(3) DVSS
RA1
RA2
RA3
DVDD18
DVDD3
RCLK
RA11
RA9
RA8
(3)DVSS
RA7
(18) DVSS
RA6
RA5
RA4
(PU) RD3/ASDATA5
(PU) RD30
RD29
DVDD18
RD26
RD25
RD24
(PD) DQM3
(PD) DQM2
DVDD3
DACVDDC
VREF
FS
192
191
190
189
DVDD3
VSYN/V_ADIN1
YUT7/ASDATA5
SPMCLK
SPDATA
SPLRCK
SPBCK/ADTA5
(PD) ALRCK
ABCK
ACLK
(18) DVSS
(PD) ASDATA1
(PD) ASDATA2
(PD) ASDATA3
(PD) ASDATA0
DVDD18
(PD) ASDATA4
MC_DATA (PD)
SPDIF
RFGND18
RFVDD18
XTALI
JITFO
JITFN
PLLVSS
IDACEXLP
PLLVDD3
LPFON
LPFIP
LPFIN
LPFOP
ADCVDD3
ADCVSS
RFVDD3
RFRPDC
RFRPAC
HRFZC
CRTPLP
RFGND
OSP
OSN
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
YUV1/Y
YUV5/B
YUV0/CIN
(3) DVSS
NC
NC
NC
NC
NC
TROPENPWM
USB_VSS
NC
NC
DVDD3
IOCA1 (PU)
CSO/RFOP
HSYN/V_ADIN2
VREFO
TMS/V_ADIN5 (JTAG)
TPI
MD
SA
AVDD3
IREF
RFGC
OP_OUT
OP_INN
OP_INP
MIDI1
TNI
MIDI2
LDO2
LDO1
TRO
XRWE
CKE
DVDD3
YUV6/R
DACVSSA
YUV4/G
DACVDDA
YUV3/CVBS
DACVSSB
YUV2/C
DACVDDB
DACVSSC
XTALO
MT1389EXE/B2-L (DVD MT ASSY: IC4002)
• MPEG / MICON / RF-AMP
Pin Arrangement (Top view)
Data
PLL
108
Mhz
DLL VIDEO
DAC
RF
Circuits
INT_ADDA
APLL
DMPLL DMPLL
MT1389EXE/B2-L
• The information shown in the list is basic information and may not correspond exactly to that shown in the schematic diagrams.
List of IC
DV-696AV-S 71
5678
5678
C
D
F
A
B
E
• MPEG / MICON / RF-AMP Microcomputer
Block Diagram
DVD
PUH
Module
RF Amplifier Video DAC
CVBS, Y/C
Component
Videop
Video
Processor De-
interlacer
Servo IO
Spindle
Control
Memory
Controller
System
CPU
GPIO
IR/VFD
System
Parser
CPPM/CPRM
DRM
32-bit
RISC
Audio
Output
Audio
DAC
SPDIF
MPEG-1/2
JPEG
Video Decoder
Servo
Processor
Audio
DSP
Debug
Port 108Mhz
TV Encoder
Motor
Drive
FLASH
ROM
DRAM
PCM
DV-696AV-S
72
1234
1234
C
D
F
A
B
E
No. Pin Name I/O Pin Function No. Pin Name I/O Pin Function
1 AGND – Analog ground
2 DVDA I AC coupled input path A
3 DVDB I AC coupled input path B
48 TDI I Serial interface port 3 data-out
Version AD input port 4
GPIO
4 DVDC I AC coupled input path C
5 DVDD I AC coupled input path D
49 TMS I Serial interface port 3 data-in
Version AD input port 5
GPIO
6 DVDRFIP I AC coupled DVD RF signal input RFIP
7 DVDRFIN I AC coupled DVD RF signal input RFIN
50 TCK I Serial interface port 3 clock pin
Version AD input port 6
GPIO
8MA I
DC coupled main-beam RF signal input A
9MB I
DC coupled main-beam RF signal input B
51 TDO I Serial interface port 3 chip-select
Version AD input port 7
GPO
10 MC I DC coupled main-beam RF signal input C
11 MD I
DC coupled main-beam RF signal input D
52 DVDD18 –
1.8 V power pin for internal digital circuitry
12 SA I DC coupled sub-beam RF signal input A
53 IOA2 I/O Microcontroller address 2/IO
13 SB I DC coupled sub-beam RF signal input B
54 IOA3 I/O Microcontroller address 3/IO
14 SC I DC coupled sub-beam RF signal input C
55 IOA4 I/O Microcontroller address 4/IO
15 SD I DC coupled sub-beam RF signal input D
56 IOA5 I/O Microcontroller address 5/IO
16 CDFON I CD focusing error negative input
57 IOA6 I/O Microcontroller address 6/IO
17 CDFOP I CD focusing error positive input
58 IOA7 I/O Microcontroller address 7/IO
18 TNI I
3 beam satellite PD signal negative input
59 HIGHA0 I/O Microcontroller address 8
19 TPI I 3 beam satellite PD signal positive input
60 IOA18 I/O Flash address 18/IO
20 MDI1 I Laser power monitor input
61 IOA19 I/O Flash address 19/IO
21 MDI2 I Laser power monitor input
62 DVSS –
3.3 V Ground pin for internal digital circuitry
22 LDO2 O Laser driver output
63 APLLCAP I APLL External Capacitance connection
23 LDO1 O Laser driver output
64 APLLVSS – Ground pin for sudio clock circuitry
24 SVDD3 – Analog power 3.3 V
65 APLLVDD3 – 3.3 V Power pin for audio clock circuity
25 CSO O
Central servo/Positive main beam summing output
66 IOWR# I/O Flash write enable, active low/IO
26 RFLVL O
RFRP low pass, or Negative main beam summing output
67 A16 O Flash adress 16
27 SGND – Analog ground
68 HIGHA7 I/O Microcontroller address 15
28 V2REFO – Reference voltage 2.8 V
69 HIGHA6 I/O Microcontroller address 14
29 V20 I/O Reference voltage 2.0 V
70 HIGHA5 I/O Microcontroller address 13
30 VREFO I/O Reference voltage 1.4 V
71 HIGHA4 I/O Microcontroller address 12
31 FEO O Focus error monitor output
72 HIGHA3 I/O Microcontroller address 11
32 TEO O Tracking error monitor output
73 DVDD3 –
3.3 V power pin for internal digital circuitry
33 TEZISLV I/O TE Slicing Level
74 HIGHA2 I/O Microcontroller adress 10
34 OP_OUT O Op amp output
75 HIGHA1 I/O Microcontroller adress 9
35 OP_INN I Op amp negative input
76 IOA20 I/O Flash adress 20/IO
36 OP_INP I Op amp positive input
77 IOCS# I/O Flash chip select, active low/IO
37 DMO O Disk motor control output. PWM output
78 IOA1 I/O Microcontroller adress 1/IO
38 FMO O Feed motor control. PWM output
79 IOOE# I/O Flash output enable, active low/IO
39
TROPENP/WM
O Tray PWM output/Tray open output
80 DVDD3 –
3.3 V power pin for internal digital circuitry
40 PWMOUT1 O
1st General PWM output, or Version AD input9
81 AD0 I Microcontroller address/data 0
41 TRO O Tracking servo output. PDM output of
tracking servo compensator.
82 AD1 I Microcontroller address/data 1
83 AD2 I Microcontroller address/data 2
42 FOO O Focus servo output. PDM output of
focus servo compensator
84 AD3 I Microcontroller address/data 3
85 DVSS –
1.8 V Ground pin for internal digital circuitry
43 DVSS – 1.8 V Ground pin for internal digital
86 AD4 I Microcontroller address/data 4
44 NC – –
87 AD5 I Microcontroller address/data 5
45 NC – –
88 AD6 I Microcontroller address/data 6
• MPEG/MICON/RF-AMP CPU
Pin Function
MT1389EXE/B2-L (DVD MT ASSY : IC4002)
46 DVDD3 –
3.3 V power pin for internal digital circuitry
47
FG(Diogital pin)
–
Motor Hall sensor input, or Version AD input 8
89 IOA21 I/O Flash address 21/IO
While External FLASH size <= 2MB:
Version AD input port 0, or
GPIO
90 ALE I/O Microcontroller address latch enable
DV-696AV-S 73
5678
5678
C
D
F
A
B
E
No. Pin Name I/O Pin Function No. Pin Name I/O Pin Function
91 AD7 I Microcontroller address/data 7
92 A17 O Flash address 17
93 IOA0 I/O Microcontroller address 0/IO
94 DVSS –
3.3 V Ground pin for internal digital circuitry
137 DQM1 I/O Data mask 1
95 UWR# I Microcontroller write strobe, active low
138 RWE# O DRAM Write enable, active low
96 URD# I Microcontroller read strobe, active low
139 CAS# O
DRAM column address strobe, active low
97 DVDD18 –
1.8 V power pin for internal digital circuitry
140 RAS# O DRAM row address strobe, active low
98 UP1_2 I/O Microcontroller port 1-2
141 DVDD3 –
3.3 V power pin for internal digital circuitry
99 UP1_3 I/O Microcontroller port 1-3
142 RCS# O DRAM chip select, active low
100 UP1_4 I/O Microcontroller port 1-4
143 BA0 I/O DRAM bank address 0
101 UP1_5 I/O Microcontroller port 1-5
144 DVSS –
1.8 V Ground pin for internal digital circuitry
102 UP1_6 I/O Microcontroller port 1-6
I2C clock pin
145 BA1 I/O DRAM bank address 1
146 RA10 I/O DRAM address 10
103 UP1_7 I/O Microcontroller port 1-7
I2C data pin
147 RA0 I/O DRAM address 0
148 DVSS –
3.3 V Ground pin for internal digital circuitry
104 UP3_0 I/O Microcontroller port 3-0
8032 RS232 RXD
149 RA1 I/O DRAM address 1
150 RA2 I/O DRAM address 2
105 UP3_1 I/O Microcontroller port 3-1
8032 RS232 TXD
106 UP3_4 I/O Microcontroller port 3-4
Hardwired RD232 RXD
I2C clock pin
107 UP3_5 I/O Microcontroller port 3-5
Hardwired RD232 TXD
I2C data pin
108 DVDD3 –
3.3 V power pin for internal digital circuitry
109 ICE I Microcontroller ICE mode enable
110 PRST# I Power on reset input, active low
111 IR I IR control signal input
112 INT0# I/O
Microcontroller external interrupt 0, active low
113 DQM0 I/O Data mask 0
114 DQS0 I/O GPIO
115 RD7 I/O DRAM data 7
116 DVSS –
1.8 V Ground pin for internal digital circuitry
117 RD6 I/O DRAM data 6
118 RD5 I/O DRAM data 5
119 DVSS –
3.3 V Ground pin for internal digital circuitry
120 RD4 I/O DRAM data 4
121 RD3 I/O DRAM data 3
122 DVDD18 –
1.8 V power pin for internal digital circuitry
123 RD2 I/O DRAM data 2
124 RD1 I/O DRAM data 1
125 RD0 I/O DRAM data 0
126 RD15 I/O DRAM data 15
127 DVDD3 –
3.3 V power pin for internal digital circuitry
128 RD14 I/O DRAM data 14
129 RD13 I/O DRAM data 13
152 DVDD18 –
1.8 V power pin for internal digital circuitry
153 NC – –
154 NC – –
155 DVDD3 –
3.3 V power pin for internal digital circuitry
156 RCLK I/O Dram clock
157 CKE O DRAM clock enable
158 RA11 I/O DRAM address bit 11
159 RA9 I/O DRAM address 9
160 RA8 I/O DRAM address 8
161 DVSS –
3.3 V Ground pin for internal digital circuitry
162 RA7 I/O DRAM address 7
163 DVSS –
1.8 V Ground pin for internal digital
164 RA6 I/O DRAM address 6
165 RA5 I/O DRAM address 5
166 RA4 I/O DRAM address 4
167 DVDD3 –
3.3 V power pin for internal digital circuitry
168 RD31 I/O GPIO
169 RD30 I/O GPIO
170 RD29 I/O GPIO
171 NC – –
172 NC – –
173 DVDD18 –
1.8 V power pin for internal digital circuitry
174 RD26 I/O GPIO
175 NC – –
176 RD25 I/O GPIO
177 RD24 I/O GPIO
178 DQM3 I/O GPIO
151 RA3 I/O DRAM address 3
130 RD12 I/O DRAM data 12
131 RD11 I/O DRAM data 11
132 RD10 I/O DRAM data 10
133 RD9 I/O DRAM data 9
134 DVSS –
3.3 V Ground pin for internal digital circuitry
135 RD8 I/O DRAM data 8
136 DQS1 I/O GPIO
179 DQM2 I/O GPIO
180 NC – –
181 NC – –
182 DVDD3 –
3.3 V power pin for internal digital circuitry
183 NC – –
184 NC – –
185 NC – –
186 NC – –
187 NC – –
188 NC – –
DV-696AV-S
74
1234
1234
C
D
F
A
B
E
No. Pin Name I/O Pin Function No. Pin Name I/O Pin Function
220 ASDATA3 I/O
Audio serial data 3 (Center-back/Center-left-
back/Center-right-back, in 6.1 or 7.1 mode)
DSD data right surround channel
Trap value in power-on reset:
1:manufactory test mode
0:normal operation
While only 2 channels output:
GPIO
221 DVDD18 –
1.8V power pin for internal digital circuitry
222 ASDATA4 I/O
Audio serial data 4 (Down-mixed Left/Right)
DSD data center channel
Trap value in power-on reset:
1:manufactory test mode
0:normal operation
While only 2 channels output:
Microcontroller external interrupt 1
GPIO
223 DVSS –
3.3 V Ground pin for internal digital circuitry
224 MC_DATA I/O Microphone serial input
While not support Microphone:
Microcontroller external interrupt 2
GPIO
225 SPDIF O SPDIF output
226 RFGND18 – Analog ground
227 RFVDD18 – Analog power 1.8V
228 XTALO O 27 M crystal out
229 XTALI I 27 M crystal in
189 DACVDDC – 3.3 V power pin for VIDEO DAC circuitry
230 JITFO O The output terminal of RF jitter meter
190 VREF – Bandgap reference voltage
231 JITFN I The input terminal of RF jitter meter
191 FS – Full scale adjustment
232 PLLVSS –
Ground pin for data PLL and related analog circuitry
192 YUV0 O Video data output bit 0
Compensation capacitor
233 IDACEXLP O Data PLL DAC Low-pass filter
193 DACVSSC – Ground pin for VIDEO DAC circuitry
234 PLLVDD3 –
Power pin for data PLL and related analog circuitry
194 YUV1 O Video data output bit 1
Analog Y output
235 LPFON O
The negative output of loop filter amplifier
195 DACVDDB – 3.3 V power pin for VIDEO DAC circuitry
236 LPFIP I
The positive input terminal of loop filter amplifier
196 YUV2 O Video data output bit 2
Analog chroma output
237 LPFIN I
The negative input terminal of loop filter amplifier
197 DACVSSB – Ground pin for VIDEO DAC circuitry
238 LPFOP O The positive output of loop filter amplifier
198 YUV3 O Video data output bit 3
Analog composite output
199 DACVDDA – 3.3 V power pin for VIDEO DAC circuitry
200 YUV4 O Video data output bit 4
Green or Y
201 DACVSSA – Ground pin for VIDEO DAC circuitry
202 YUV5 O Video data output bit 5
Blue or CB
203 YUV6 O Video data output bit 6
Red or CR
204 DVDD3 –
3.3 V power pin Video DAC digital circuitry only
205 VSYN I/O Vertical sync input/output
While no External TV-encoder:
Vertical sync for video-input
Version AD input port 1
GPIO
206 YUV7 I/O Video data output bit 7
While no External TV-encoder:
Microcontroller external interrupt 3
Audio serial data 5 part II:DSD data sub-
woofer channel or Microphone output
GPIO
207 HSYN I/O Horizontal sync input/output
While no External TV-encoder:
Horizontal sync for video-input
Microcontroller external interrupt 4
Version AD input port 2
GPIO
208 SPMCLK I/O Audio DAC master clock of SPDIF input
While SPDIF input is not used:
Serial interface port 0 clock pin
GPIO
209 SPDATA I/O Audio data of SPDIF input
While SPDIF input is not used:
Serial interface port 0 data-in
GPIO
210 SPLRCK I/O
Audio left/right channel clock of SPDIF input
While SPDIF input is not used:
Serial interface port 0 data-out
GPIO
211 SPBCK I/O Audio bit clock of SPDIF input
While SPDIF input is not used:
Serial interface port 0 chip select
Audio serial data 5 part I:DSD data sub-
woofer channel or Microphone output
GPIO
212 DVDD3 –
3.3 V power pin for internal digital circuitry
219 ASDATA2 I/O Audio serial data 2 (Center/LFE)
DSD data left surround channel
Trap value in power-on reset:
1:manufactory test mode
0:normal operation
While only 2 channels output:
GPO
213 ALRCK I/O Audio left/right channel clock
Trap value in power-on reset:
1:use external 373
0:use internal 373
214 ABCK O Audio bit clock
Phase de-modulation
215 ACLK I/O Audio DAC master clock
216 DVSS –
1.8 V Ground pin for internal digital
217 ASDATA0 I/O
Audio serial data 0 (Front-Left/Front-Right)
DSD data left channel
Trap value in power-on reset:
1:manufactory test mode
0:normal operation
218 ASDATA1 I/O
Audio serial data 1 (Left-Surround/Right-Surround)
DSD data right channel
Trap value in power-on reset:
1:manufactory test mode
0:normal operation
While only 2 channels output:
GPO
DV-696AV-S 75
5678
5678
C
D
F
A
B
E
No. Pin Name I/O Pin Function No. Pin Name I/O Pin Function
239 ADCVDD3 – Analog 3.3 V Power for ADC
240 NC –
242 NC ––
243 NC – –
244 RFVDD3 – Analog Power
245 RFRPDC O RF ripple detect output
246 RFRPAC I
RF ripple detect input (through AC-coupling)
247 HRFZC I High frequency RF ripple zero crossing
249 RFGND – Analog Power
250 NC ––
251 NC – –
252 OSP O
RF Offset cancellation capacitor connecting
253 OSN O
RF Offset cancellation capacitor connecting
254 RFGC O
RF AGC loop capacitor connecting for DVD-ROM
255 IREF I Current reference input. It generates
reference current for RF path. Connect
an external 15K resistor to this pin and
AVSS
256 AVDD3 – Analog power 3.3 V
241 ADCVSS – Analog ground for ADC
–
248 CRTPLP O Defect level filter capacitor connecting
DV-696AV-S
76
1234
1234
C
D
F
A
B
E
7.5 DISC / CONTENT FORMAT PLAYBACK COMPATIBILITY
Disc / content format playback
compatibility
This player is compatible with a wide range of
disc types (media) and formats. Playable discs
will generally feature one of the following logos
on the disc and/or disc packaging. Note
however that some disc types, such as
recordable CD and DVD, may be in an
unplayable format—see below for further
compatibility information.
Pleasealso note that recordable discs cannot be
recorded using this player.
• This unit will play DVD+R/+RW discs.
• is a trademark of DVD Format/Logo
Licensing Corporation.
• is a trademark of Fuji Photo Film Co. Ltd.
• Also compatible with KODAK Picture CD
This player supports the IEC’s Super VCD
standard. Compared to the Video CD standard,
Super VCD offers superior picture quality, and
allows two stereo soundtracks to be recorded.
Super VCD also supports the widescreen size.
About DualDisc playback
A DualDisc is a new two -sided disc, one side
of which contains DVD content video, audio,
etc. while the other side contains non-DVD
content such as digital audio material.
The non-DVD, audio side of the disc is not
compliant with the CD Audio specification and
therefore may not play.
The DVD side of a DualDisc plays in this
product.
Formore detailed information on the DualDisc
specification, please refer to the disc
manufacturer or disc retailer.
CD-R/RW compatibility
• Compatible formats: CD-Audio, Video CD ,
ISO 9660 CD-ROM* containing MP3,
WMA, JPEG or DivX video files
* ISO 9660 Level 1 or 2 compliant. CD
physical format: Mode1, Mode2 XA Form1.
Romeo and Joliet file systems are both
compatible with this player.
• Multi-session playback: No
• Unfinalized disc playback: No
• Filestructure (may differ): Up to 299 folders
on a disc; up to 648 folders and files
(combined) within each folder
DVD-Video DVD-R DVD-RW
Video CD
Fujicolor CD
Audio CD CD-R CD-RW
DVD+R/DVD+RW compatibility
Only DVD+R/DVD+RW discs recorded in
‘Video Mode (DVD Video Mode)’ which have
been finalized, can be played back. However,
some editing made during the recording may
not be played back accurately.
DVD-R/RW compatibility
•Compatible formats: DVD-Video, Video
Recording (VR)*
* Editpoints may not play exactly as edited;
screen may go momentarily blank at edited
points.
•Unfinalized playback: No
•WMA/MP3/JPEG file playback on DVD-R/
RW: No
Compressed audio compatibility
•Compatible formats: MPEG-1 Audio Layer 3
(MP3), Windows Media Audio (WMA)
•Sampling rates: 32 kHz, 44.1 kHz or 48 kHz
•Bit-rates: Any (128 Kbps or higher
recommended)
•VBR (variable bit rate) MP3 playback: No
•VBR WMA playback: No
•WMA lossless encoding compatible: No
•DRM (Digital Rights Management)
compatible: Yes (DRM-protected audio
files will not play in this player—see also
DRM in the Glossary)
•Fileextensions: .mp3, .wma (these must be
used for the player to recognize MP3 and
WMA files – do not use for other file types)
DV-696AV-S 77
5678
5678
C
D
F
A
B
E
About WMA
The Windows Media ® logo printed on the box
indicates that this player can playback
Windows Media Audio content.
WMA is an acronym for Windows Media Audio
and refers to an audio compression technology
developed by Microsoft Corporation. WMA
content can be encoded by using Windows
Media Player version 7, 7.1, Windows Media
®®
Player for Windows XP, or Windows Media
®®
Player 9 Series.
Microsoft, Windows Media, and the Windows
logo are trademarks, or registered trademarks of
Microsoft Corporation in the United States and/
or other countries.
About DivX
DivX is a compressed digital video format
created by the DivX video codec from DivX,
®
Inc.This player can play DivX video files burned
on CD-R/RW/ROM discs. Keeping the same
terminology as DVD-Video, individual DivX
video files are called "Titles". When naming
files/titles on a CD-R/RW disc prior to burning,
keep in mind that by default they will be played
in alphabetical order.
Displaying DivX subtitle files
The font sets listed below are available for DivX
external subtitle files. You can see the proper
font set on-screen by setting the Subtitle
Language to match the subtitle file.
This player supports the following language
groups:
Group 1: Albanian (sq), Basque (eu), Catalan (ca),
Danish (da), Dutch (nl), English (en), Faroese (fo),
Finnish (fi), French (fr), German (de), Icelandic (is), Irish
(ga), Italian (it), Norwegian (no), Portuguese (pt), Rhaeto-
Romanic (rm), Scottish (gd), Spanish (es), Swedish (sv)
Group 2: Albanian (sq), Croatian (hr), Czech (cs),
Hungarian (hu), Polish (pl), Romanian (ro), Slovak (sk),
Slovenian (sl)
Group 3: Bulgarian (bg), Byelorussian (be), Macedonian
(mk), Russian (ru), Serbian (sr), Ukrainian (uk)
Group 4: Hebrew (iw), Yiddish (ji)
Group 5: Turkish (tr)
• Some external subtitle files may be
displayed incorrectly or not at all.
• For external subtitle files the following
subtitle format filename extensions are
supported (please note that these files are
not shown within the disc navigation
menu): .srt, .sub, .ssa, .smi
• The filename of the movie file has to be
repeated at the beginning of the filename
for the external subtitle file.
• The number of external subtitle files which
can be switched for the same movie file is
limited to a maximum of 10.
DivX video compatibility
• Official DivX Certified product.
®
• Playsall versions of DivX video (including
®
DivX 6) with standard playback of DivX
®®
media files.
• File extensions: .avi and .divx (these must
be used for the player to recognize DivX
video files). Note that all files with the .avi
extension are recognized as MPEG4, but not
all of these are necessarily DivX video files
and therefore may not be playable on this
player.
DivX, DivX Certified, and associated logos are
trademarks of DivX, Inc. and are used under
license.
JPEG file compatibility
• Compatible formats: Baseline JPEG and
EXIF2.2* still image files up to a resolution
of 3072 x 2048.
*File format used by digital still cameras.
• Progressive JPEG compatible: No
• File extensions: .jpg (must be used for the
player to recognize JPEG files – do not use
for other file types)
PC-created disc compatibility
Discs recorded using a personal computer
may not be playable in this unit due to the
setting of the application software used to
create the disc. In these particular instances,
check with the software publisher for more
detailed information.
Discs recorded in packet write mode (UDF
format) are not compatible with this player.
Check the DVD-R/RW or CD-R/RW software
disc boxes for additional compatibility
information.
DV-696AV-S
78
1234
1234
C
D
F
A
B
E
8. PANEL FACILITIES
8.1 FRONT PANEL SECTION
1 STANDBY/ON
Press to switch the player on or into standby.
2 Disc tray
3
9 OPEN/CLOSE
Press to open or close the disc tray.
4
11
Press to pause playback. Press again to
restart.
5
10
Press to start or resume playback.
12
Press to stop the disc (you can resume play-
back by pressing (play)).
Compatible
8 Display
Description of the display.
13 and 
• Press and hold for fast reverse/forward
scanning.
• Press to jump to the previous/next
chapter or track.
17
This mark indicates compatibility with
DVD-RW discs recorded on a DVD recorder
in Video Recording mode.
TOP MENU
ENTER & cursor buttons
MENU
6 RETURN
7 HOME MENU
16 HDMI indicator
Lights when this player is recognized by
another HDMl or DVI/HDCP compatible
component.
Front panel
Displays the ‘top menu’ of a DVD
disc—this varies with the disc.
Displays a DVD disc menu—this varies with the disc
and may be the same as the ‘top menu’.
Selects the current menu option.
Returns to the previously dis-played menu screen.
23 4 5
6781017 16 9111213
1
DV-696AV
DV-696AV-S 79
5678
5678
C
D
F
A
B
E
8.2 REMOTE CONTROL
Remote control
1
Press to switch the player on or into standby.
2AUDIO
Press to select the audio channel or language.
3SUBTITLE
Press to select a subtitle display.
4Number buttons
5TOP MENU
Press to display the top menu of a DVD disc.
6ENTER & cursor buttons
Use to navigate on-screen displays and
menus. Press ENTER to select an option or
execute a command.
7HOME MENU
Press to display (or exit) the on-screen
display.
8
Use for reverse slow motion playback, frame
reverse and reverse scanning.
9
Press to start or resume playback.
10
Press to jump to the beginning of the current
chapter or track, then to previous chapters/
tracks.
11
Press to pause playback; press again to
restart.
12 PLAY MODE
Press to display the Play Mode menu. (You
can also get to the Play Mode menu by
pressing HOME MENU and selecting Play
Mode).
DV-696AV-S
80
1234
1234
C
D
F
A
B
E
Remote control 2
13 SURROUND
Press to activate/switch off 2V/SRS TruSurround.
14
Press to open or close the disc tray.
15 ANGLE
Press to change the camera angle during
DVD multi-angle scene playback.
16 CLEAR
Press to clear a numeric entry.
17 ENTER
Use to select menu options, etc.
18 MENU
Press to display a DVD disc menu, or the Disc
Navigator if a VR format DVD-RW, CD, Video
CD , MP3, WMA or JPEG disc is loaded.
19 RETURN
Press to return to a previous menu screen.
20
Use for forward slow motion playback, frame
advance and forward scanning.
21
Press to jump to the next chapter or track.
22
Press to stop the disc (you can resume playback
by pressing (play)).
23 DISPLAY
Press to display information about the disc
playing.
24 ZOOM
Press to change the zoom level.
DV-696AV-S 81
5678
5678
C
D
F
A
B
E
DV-696AV-S
82
1234
1234
C
D
F
A
B
E
Service Remote Control Unit GGF1381 diagnosis
Name Jig No. Remarks
DVD Test Disc (DVD
-Video,NTSC) GGV1025 Operation Check
CD Test Disc STD-905 Operation Check
7 Jigs list
Lubricants and Glues list
Cleaning
Daifree GEM1036 (ZLX-ME413A) Refer to "2.3 06 DVD MECHA SECTION"
Grease GYA1001 (ZLB-PN397B) Refer to "2.3 06 DVD MECHA SECTION"
Grease GYA1018 Refer to "2.3 06 DVD MECHA SECTION"
Name Lubricants and Glues No. RemarkName Lubricants and Glues No. Remark
• Before shipping out the product, be sure to clean the following positions by using the prescribed cleaning tools:
Pickup leneses Cleaning liquid : GEM1004
Cleaning paper : GED-008
Position to be cleaned Cleaning tools RemarkPosition to be cleaned Cleaning tools Remark
Refer to "2.3 06 DVD MECHA SECTION" and
Refer to "7.3 DVD DECK SECTION"

Navigation menu