DV Power Protective Earth Resistance Meter RMO60E User Manual Brochure
User Manual: DV-Power-Protective-earth-resistance-meter-RMO60E-User-Manual-Brochure
Open the PDF directly: View PDF 
.
Page Count: 4
| Download | |
| Open PDF In Browser | View PDF |
Protective earth resistance meter RMO60E Lightweight – only 7,5 kg Powerful 10 A – 60 A DC Measuring range 100 µΩ – 999,9 m Resolution to 0,1 SINGLE / CONTIN Mode Mechanical protection IP43 Description RMO60E is ideal for testing the protective bonding (grounding) of equipment following the standard 61010-1 IEC 2001.This standard specifies for plug connected equipment and for permanently connected equipment the following requirements: The protective earth resistance should be below 0,1Ω or voltage between the protective conductor terminal and each accessible conductive part for which protective bonding is required not to exceed 10V. Conformity is checked by applying a test current for 1 minute and then calculating impedance, or measuring the voltage between the protective conductor terminal and each accessible conductive part for which protective bonding is required. The test current should be greater of 25A or twice the rated current for plug connected equipment, or twice the value of the overcurrent protection for the permanently connected equipment. B-RMO60EN-301-EN For both of these applications RMO60E can provide the right tool for verification of the conformity. Applying current up to the value of 60A and the ability of RMO60E to provide in the Contin menu (continuous operation) test current for the pre-set test duration (equal or exceeding 1 min) - gives an user possibility to easily check the protective bonding/grounding of the equipment. The full load voltage of 12V assures that the measurement is executed properly and that the result obtained (pass fail classification) is accurate. RMO60E generates true DC current with automatically regulated test ramps. During the test RMO60E ramps with increasing current before measuring and decreasing current after the measurement. This eliminates magnetic transients. After the test current has been set, the automatic test procedure is started by pressing the Ω-button. The RMO60E instrument can store up to 500 measurements. All measurements are time and date stamped. Using DV-Win software a test can be performed from a PC, and the results can be obtained directly at a PC Communication between RMO60E and PC is through USB or RS232 cable. Using DV-Win the result can be arranged as an Excel spread sheet which can be later shown as a diagram and printed for a report. The set is equipped with thermal and overcurrent protection. The RMO60E has very high ability to cancel electrostatic and electromagnetic interference in HV electric fields. It is achieved by very efficient filtration. The filtration is made utilizing proprietary hardware and software. 2016-05-11 1 Output Ratings CONTIN Mode The full output is available from the RMO60E at 230 V or 115 V Mains Supply. RMO60E can generate a DC current continuously using the CONTIN menu. In this menu the current can be chosen the same way as in the SINGLE menu, but the duration of the test can be preset. The test is started pressing the Ω-button. During the test, a new result is shown on the display and stored into the PC (DV-Win) each second. Using DV-Win the result can be arranged as an Excel spreadsheet which can be later shown as a diagram and printed for a report. Supply Voltage Output Current Full Load Voltage 230 V AC 60 A DC smoothed 12,0 V DC 115 V AC 60 A DC smoothed 12,0 V DC Output current is filtered and has a ripple of less than 1 %. Output current is filtered and has a ripple of less than 1 %. Application Typical application is measuring of protective earth resistance of equipment in compliance with IEC 61010-1 safety standard. Other application is measuring resistance of: High, middle and low voltage circuit breakers High, middle and low voltage disconnecting switches High-current bus bar joints Cable splices Welding joints B-RMO60EN-301-EN 2016-05-11 2 Technical data Mains power supply Environmental conditions Connection according to IEC/EN60320-1; -10 ºC - + 55 ºC / 14 ºF - +131 ºF C320 Mains supply: 90 V – 264 V AC Frequency: 50 / 60 Hz 12 A / 250 V, type F Test current Full Load Voltage12,0 V DC at 60 A 10 A - 60 A DC Installation/overvoltage category II Pollution degree 2 Dimensions and weight *At 230 V of supply voltage Measurement Resistance range 100,0 µΩ - 999,9 mΩ Resolution: 100 - 999,9 0,1 µΩ 1,000 m - 9,999 m 1,0 µΩ 10,00 m - 99,99 m 10 µΩ 100,0 m - 999,9 m 0,1 mΩ Typical accuracy± (0,1 % rdg + 0,1 % FS) LCD screen 20 characters by 4 lines; LCD Dimensions (W x H x D): 198 mm x 255 mm x 380 mm 7,8 in x 10 in x 15 in Weight: 7,5 kg/16,5 lb Warranty 3 Years Safety Standards European standardsEN 61010-1 LVD 2006/95/EC Display International standardsIEC 61010-1 display with backlight, visible in bright UL 61010-1 sunlight CAN/CSA-C22.2 No. 61010-1, 2nd edition, Interface RMO60E is equipped with an USB port including Amendment 1 Electromagnetic Compatibility (EMC) (optional: RS232) to connect to an external CE conformityEMC standard 89/336/EEC computer EmissionEN 50081-2, EN 61000-3-2/3 B-RMO60EN-301-EN Test Result Storage Humidity 5 % - 95 % relative humidity, non condensing Storage & transportation: -40 ºC - + 70ºC / -40 ºF - +158 ºF Output data Operating temperature: Interference ImmunityEN 50082-2 RMO60E can store up to 500 measurements 2016-05-11 All specifications herein are valid at ambient temperature of + 25 °C and recommended accessories. Specifications are subject to change without notice 3 Current cables Extension current cables Voltage sense cables Test shunt Transport case Cable bag Order info B-RMO60EN-301-EN Instrument with included accessories Micro Ohmmeter RMO60E DV-Win PC software Ground cable USB cable Article No RMO60E-N-00 Recommended accessories Current cables 2 x 5 m 10 mm2 Sense cables 2 x 5 m with alligator clips Transport case Article No C2-05-10LMB1 S2-05-02BPA1 HARD-CASE-ME Optional Cable bag Test shunt 100 µΩ (600 A/60 mV) Current cables 2 x 10 m, 10 mm² with battery clips Current cables 2 x 15 m,16 mm² with battery clips Current extension cable 2 x 10 m, 16 mm² Sense cables, extension 2 x 10 m Sense cables 2 x 10 m with alligator clips Sense cables 2 x 15 m with alligator clips Built-in thermal printer Article No CABLE-BAG-00 SHUNT-600-MK C2-10-10LMB1 C2-15-16LMB1 E2-10-16LMLF E2-10-02BPBP S2-10-02BPA1 S2-15-02BPA1 PRINT-080-00 2016-05-11 IBEKO Power AB Stockholmsvägen 18 181 50 Lidingö, Sweden Contact Phone: +46 70 0925 000 E-mail:sales@dv-power.com 4
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 4 Language : en-US Tagged PDF : Yes Author : Rizvan Semin Creator : Microsoft® Word 2010 Create Date : 2016:05:11 10:55:56+02:00 Modify Date : 2016:05:11 10:55:56+02:00 Producer : Microsoft® Word 2010EXIF Metadata provided by EXIF.tools