01 Receiving Delta_IA MDS_VFD C2000_UM_EN_20140826 Delta IA MDS VFD C2000 UM EN 20140826

User Manual: Delta_IA-MDS_VFD-C2000_UM_EN_20140826

Open the PDF directly: View PDF .
Page Count: 692

Download
Open PDF In Browser	View PDF

Delta Classical Field Oriented Control AC Motor Drive C2000 Series User Manual

201408

Delta Classical Field Oriented
Control AC Motor Drive
C2000 Series User Manual

PLEASE READ PRIOR TO INSTALLATION FOR SAFETY.
 AC input power must be disconnected before any wiring to the AC motor drive is made.
 Even if the power has been turned off, a charge may still remain in the DC-link
DANGER

capacitors with hazardous voltages before the POWER LED is OFF. Please do not
touch the internal circuit and components.
 There are highly sensitive MOS components on the printed circuit boards. These
components are especially sensitive to static electricity. Please do not touch these
components or the circuit boards before taking anti-static measures. Never reassemble
internal components or wiring.
 Ground the AC motor drive using the ground terminal. The grounding method must
comply with the laws of the country where the AC motor drive is to be installed.
 DO NOT install the AC motor drive in a place subjected to high temperature, direct
sunlight and inflammables.
 Never connect the AC motor drive output terminals U/T1, V/T2 and W/T3 directly to the

CAU TION

AC mains circuit power supply.
 Only qualified persons are allowed to install, wire and maintain the AC motor drives.
 Even if the 3-phase AC motor is stop, a charge may still remain in the main circuit
terminals of the AC motor drive with hazardous voltages.
 If the AC motor drive is stored in no charge condition for more than 3 months, the
ambient temperature should not be higher than 30 °C. Storage longer than one year is
not recommended, it could result in the degradation of the electrolytic capacitors.
 Pay attention to the following when transporting and installing this package (including
wooden crate, wood stave and carton box)
1.

If you need to sterilize, deform the wooden crate or carton box, please do not
use steamed smoking sterilization or you will damage the VFD.

2.

Please use other ways to sterilize or deform.

3.

You may use high temperature to sterilize or deform. Leave the packaging
materials in an environment of over 56℃ for 30 minutes.

4.

It is strictly forbidden to use steamed smoking sterilization.

The warranty does

not covered VFD damaged by steamed smoking sterilization.
NOTE

The content of this manual may be revised without prior notice. Please consult our distributors or download the most updated
version at http://www.delta.com.tw/industrialautomation

I

Table of Contents
CHAPTER 1 INTRODUCTION ..................................................................................................................1-1
1-1 Receiving and Inspection..................................................................................................1-1
1-2 Nameplate Information.....................................................................................................1-1
1-3 Model Name....................................................................................................................1-2
1-4 Serial Number.................................................................................................................1-2
1-5 RFI Jumper.....................................................................................................................1-3
1-6 Dimensions.....................................................................................................................1-7
CHAPTER 2 INSTALLATION ..................................................................................................................2-1
2-1 Minimum Mounting Clearance and Installation......................................................................2-1
2-2 Minimum mounting clearance.............................................................................................2-2
CHAPTER 3 UNPACKING ........................................................................................................................3-1
3-1 Unpacking.........................................................................................................................3-1
3-2 The Lifting Hook..............................................................................................................3-13
CHAPTER 4 WIRING ................................................................................................................................4-1
4-1 Wiring...............................................................................................................................4-1
4-2 System Wiring Diagram.....................................................................................................4-6
CHAPTER 5 MAIN CIRCUIT TERMINALS .............................................................................................5-1
5-1 Main Circuit Diagram.........................................................................................................5-1
5-2 Main Circuit Terminals.......................................................................................................5-5
CHPATER 6 CONTROL TERMINALS ......................................................................................................6-1
6-1 Specifications of Control Terminal........................................................................................6-3
6-2 Analog input terminals (AVI, ACI, AUI, ACM) .......................................................................6-5
6-3 Remove the Terminal Block................................................................................................6-7
CHAPTER 7 OPTIONAL ACCESSORIES .............................................................................................7-1
7-1 All Brake Resistors and Brake Units Used in AC Motor Drives................................................7-2
7-2 Non-fuse Circuit Breaker....................................................................................................7-5
7-3 Fuse Specification Chart ....................................................................................................7-6
7-4 AC/DC Reactor..................................................................................................................7-7
7-5 Zero Phase Reactor.........................................................................................................7-10
7-6 EMI Filter........................................................................................................................7-12
7-7 Digital Keypad.................................................................................................................7-16
7-8 Panel Mounting...............................................................................................................7-19
7-9 Conduit Box Kit...............................................................................................................7-21
7-10 Fan Kit.........................................................................................................................7-29
II

7-11 Flange Mounting Kit ......................................................................................................7-42
7-12 USB/RS-485 Communication Interface IFD6530…........................................................7-55
CHAPTER 8 OPTION CARDS ..................................................................................................................8-1
8-1 Removed key cover...........................................................................................................8-2
8-2 Screws Specification for option card terminals.....................................................................8-5
8-3 EMC-D42A......................................................................................................................8-10
8-4 EMC-D611A....................................................................................................................8-10
8-5 EMC-R6AA.....................................................................................................................8-10
8-6 EMC-BPS01....................................................................................................................8-11
8-7 EMC-PG01/02L...............................................................................................................8-12
8-8 EMC-PG01/02O..............................................................................................................8-15
8-9 EMC-PG01/02U...............................................................................................................8-18
8-10 EMC-PG01R.................................................................................................................8-20
8-11 CMC-MOD01.................................................................................................................8-22
8-12 CMC-PD01....................................................................................................................8-26
8-13 CMC-DN01....................................................................................................................8-28
8-14 CMC-EIP01...................................................................................................................8-31
8-15 EMC-COP01.................................................................................................................8-36
CHAPTER 9 SPECIFICATION ..................................................................................................................9-1
9-1 230V Series…………………………………...........................................................................9-1
9-2 460V Series…………………………………...........................................................................9-2
9-3 Environment for Operation, Storage and Transportation………………………….......................9-4
9-4 Specification for Operation Temperature and Protection Level…….........................................9-5
9-5 Derating of ambient tempeture and altitude…………………….……........................................9-6
CHAPTER 10 DIGITAL KEYPAD ...........................................................................................................10-1
10-1 Descriptions of Digital Keypad ………………………………….............................................10-2
10-2 Function of Digital Keypad KPC-CC01.............................................................................10-5
10-3 TPEditor Installation Instruction ....................................................................................10-23
10-4 Fault Code Description of Digital Keypad KPC-CC01.......................................................10-36
CHAPTER 11 SUMMARPY OF PARAMETERS ..................................................................................... 11-1
CHAPTER 12 DESCRIPTION OF PARAMETER SETTINGS ................................................................12-1
CHAPTER 13 WARNING CODES ..........................................................................................................13-1
CHAPTER 14 FAULT CODES AND DESCRIPTIONS............................................................................14-1
CHAPTER 15 CANOPEN OVERVIEW ...................................................................................................15-1
CHAPTER 16 PLC FUNCTION ..............................................................................................................16-1
CHAPTER 17 HOW TO SELECT THE RIGHT AC MOTOR DIRVE .......................................................17-1
III

CHAPTER 18 SUGGESTIONS AND ERROR CORRECTIONS FOR STANDARD AC MOTOR DRIVES
.................................................................................................................................................................18-1
CHAPTER 19 EMC STANDARD INSTALLATION GUIDE………………………………………………….19-1
CHAPTER 20 SAFETY TORQUE OFF FUNCTION………………………………………………………….20-1
APPENENDIX A. PUBLICATION HISTORY…………………………………………………………………..A-1

Application

Control BD V1.20;
Keypad
V1.04;

IV

Chapter 1 IntroductionC2000 Series

Chapter 1 Introduction
1-1 Receiving and Inspection
After receiving the AC motor drive, please check for the following:
1.

Please inspect the unit after unpacking to assure it was not damaged during shipment. Make sure that
the part number printed on the package corresponds with the part number indicated on the
nameplate.

2.

Make sure that the voltage for the wiring lie within the range as indicated on the nameplate. Please
install the AC motor drive according to this manual.

3.

Before applying the power, please make sure that all the devices, including power, motor, control
board and digital keypad, are connected correctly.

4.

When wiring the AC motor drive, please make sure that the wiring of input terminals “R/L1, S/L2, T/L3”
and output terminals”U/T1, V/T2, W/T3” are correct to prevent drive damage.

5.

When power is applied, select the language and set parameter groups via the digital keypad
(KPC-CC01). When executes trial run, please begin with a low speed and then gradually increases
the speed untill the desired speed is reached.

1-2 Nameplate Information
AC Driv e Model
Input Volt age/Current
Output Voltage/Current

MODE L:VFD0 07 C43 A
INPUT:
Nor mal D uty: 3 PH 3 80 -4 80 V 5 0/6 0Hz 4 .3A
Hea vy D uty: 3 PH 3 80 -4 80 V 5 0/6 0Hz 4 .1A

OUTPUT:
Nor mal D uty: 3 PH 0 -4 80 V 3 A 2 .4 KVA 1 HP
Hea vy D uty: 3 PH 0 -4 80 V 2 .9A 2 .3K VA 1 HP

Frequency Range
Firmware Version

FREQUENCY RANGE:
Normal Duty: 0-600Hz
Heavy Dut y: 0-300Hz
Ver si on: VX.XX

Cert ifications
Enclosure type (IPXX)
007C43A7T14300002

Serial Number

DELTA ELECTRONICS. INC.
MADE IN XXXXXXX

1-1

Chapter 1 IntroductionC2000 Series

1-3 Model Name

VFD 007 C 43 A
Ve rs io n ty p e
A: Wall mounted
S: Same capacity but miniaturized
(conduit box included)
U: Same capacity but miniaturized
In p u t v o lta g e
23:230V 3-PHASE
43:460V 3-PHASE
C2 0 0 0 se rie s
A p p lic a b le mo to r c a p a c ity
0 0 7 :1 HP(0 .7 5 k W )~ 4 5 0 0 :6 0 0 HP(4 5 0 kW )
Re fe r to th e s p e c ifica tio n s fo r d e ta ils
S e rie s n a me (Va ria b le F re q u e n c y Driv e )

1-4 Serial Number

007C43A T 1 4 3 0 0002
Prod uction n umber
Produ cti on we ek
T: Ta uyuan W: W uji an
S: S han gha i
460 V 3-PHASE 1 H P(0.7 5kW)

1-2

Pro ductio n ye ar
Produ cti on factory
Mod el nu mb er

Chapter 1 IntroductionC2000 Series

1-5 RFI Jumper
RFI Jumper: The AC motor drive may emit the electrical noise. The RFI jumper is used to suppress the
interference (Radio Frequency Interference) on the power line.

Frame A~C
Screw Torque: 8~10kg-cm(6.9-8.7 lb -in.)
Loosen the screws and remove the MOV-PLATE. Fasten the screws back to the original position after
MOV-PLATE is removed.

1-3

Chapter 1 IntroductionC2000 Series

Frame D0~H
Remove the MOV-PLATE by hands, no screws need to be loosen.

Isolating main power from ground:
When the power distribution system of the Power Regenerative Unit is a floating ground system (IT) or an
asymmetric ground system (TN), the RFI short short-circuit cable must be cut off. Cutting off the
short-circuit cable cuts off the internal RFI capacitor (filter capacitor) between the system's frame and the
central circuits to avoid damaging the central circuits and (according to IEC 61800-3) reduce the ground
leakage current.
Important points regarding ground connection
 To ensure the safety of personnel, proper operation, and to reduce electromagnetic radiation, the
Power Regenerative Unit must be properly grounded during installation.
 The diameter of the cables must meet the size specified by safety regulations.
 The shielded cable must be connected to the ground of the Power Regenerative Unit to meet safety
regulations.
 The shielded cable can only be used as the ground for equipment when the aforementioned points are
met.
 When installing multiple sets of Power Regenerative Units, do not connect the grounds of the Power
Regenerative Units in series. As shown below
Ground terminal

Best wiring setup for ground wires

1-4

Chapter 1 IntroductionC2000 Series

Pay particular attention to the following points:
 After turning on the main power, do not cut the RFI short-circuit cable while the power is on.
 Make sure the main power is turned off before cutting the RFI short-circuit cable.
 Cutting the RFI short-circuit cable will also cut off the conductivity of the capacitor. Gap discharge may
occur once the transient voltage exceeds 1000V.
If the RFI short-circuit cable is cut, there will no longer be reliable electrical isolation. In other words, all
controlled input and outputs can only be seen as low-voltage terminals with basic electrical isolation. Also,
when the internal RFI capacitor is cut off, the Power Regenerative Unit will no longer be electromagnetic
compatible.
 The RFI short-circuit cable may not be cut off if the main power is a grounded power system.
 The RFI short-circuit cable may not be cut off while conducting high voltage tests. When conducting a
high voltage test to the entire facility, the main power and the motor must be disconnected if leakage
current is too high.
Floating Ground System(IT Systems)
A floating ground system is also called IT system, ungrounded system, or high impedance/resistance
(greater than 30Ω) grounding system.


Disconnect the ground cable from the internal EMC filter.



In situations where EMC is required, check whether there is excess electromagnetic radiation affecting
nearby low-voltage circuits. In some situations, the adapter and cable naturally provide enough
suppression. If in doubt, install an extra electrostatic shielded cable on the power supply side between
the main circuit and the control terminals to increase security.



Do not install an external RFI/EMC filter, the EMC filter will pass through a filter capacitor, thus
connecting power input to ground. This is very dangerous and can easily damage the Power
Regenerative Unit.

Asymmetric Ground System(Corner Grounded TN Systems)
Caution: Do not cut the RFI short-circuit cable while the input terminal of the Power Regenerative Unit
carries power.
In the following four situations, the RFI short-circuit cable must be cut off. This is to prevent the system
from grounding through the RFI capacitor, damaging the Power Regenerative Unit.
RFI short-circuit cable must be cut off
1 Grounding at a corner in a triangle configuration

L1

2 Grounding at a midpoint in a polygonal
configuration

L1

L2
L2

L3

L3

1-5

Chapter 1 IntroductionC2000 Series

3 Grounding at one end in a single-phase

4 No stable neutral grounding in a three-phase

configuration

autotransformer configuration

L1

L1

L1
L2
L2
L3

N

L3

RFI short-circuit can be used
Internal grounding through RFI capacitor, which reduces

L1

electromagnetic radiation. In a situation with higher
requirements for electromagnetic compatibility, and using a
symmetrical grounding power system, an EMC filter can be
installed. As a reference, the diagram on the right is a
symmetrical grounding power system.

L2
L3

1-6

Chapter 1 IntroductionC2000 Series

1-6 Dimensions
Frame A
VFD007C23A; VFD007C43A/E; VFD015C23A; VFD015C43A/E; VFD022C23A; VFD022C43A/E;
VFD037C23A; VFD037C43A/E; VFD040C43A/E; VFD055C43A/E

Unit: mm [inch]

Frame
A1

W

H

D

W1

H1

D1*

S1

Φ1

Φ2

Φ3

130.0

250.0

170.0

116.0

236.0

45.8

6.2

22.2

34.0

28.0

[5.12]

[9.84]

[6.69]

[4.57]

[9.29]

[1.80]

[0.24]

[0.87]

[1.34]

[1.10]

D1*: Flange mounting

1-7

Chapter 1 IntroductionC2000 Series

Frame B
VFD055C23A; VFD075C23A; VFD075C43A/E; VFD110C23A; VFD110C43A/E; VFD150C43A/E

See Detail A

See Detail B

Detail A (Mounting Hole)

Detail B (Mounting Hole)
Unit: mm [inch]

Frame
B1

W

H

D

W1

H1

D1*

S1

Φ1

Φ2

Φ3

190.0

320.0

190.0

173.0

303.0

77.9

8.5

22.2

34.0

43.8

[7.48]

[12.60]

[7.48]

[6.81]

[11.93]

[3.07]

[0.33]

[0.87]

[1.34]

[1.72]

D1*: Flange mounting

1-8

Chapter 1 IntroductionC2000 Series

Frame C
VFD150C23A; VFD185C23A; VFD185C43A/E; VFD220C23A; VFD220C43A/E; VFD300C43A/E

See Detail A

See Detail B

Detail A (Mounting Hole)

Detail B (Mounting Hole)
Unit: mm [inch]

Frame
C1

W

H

D

W1

H1

D1*

S1

Φ1

Φ2

Φ3

250.0

400.0

210.0

231.0

381.0

92.9

8.5

22.2

34.0

50.0

[9.84]

[15.75]

[8.27]

[9.09]

[15.00]

[3.66]

[0.33]

[0.87]

[1.34]

[1.97]

D1*: Flange mounting

1-9

Chapter 1 IntroductionC2000 Series

Frame D0
D0-1: VFD370C43S; VFD450C43S;

D
W
W1

D1
D2

H3

H1

H2

SEE DETAIL A

S2

SEE DETAIL B

S1

S1

DETAIL A
(MOUNTING HOLE)

DETAIL B
(MOUNTING HOLE)
Unit: mm [inch]

Frame
D0-1

W

H1

D

W1

H2

H3

D1*

D2

S1

S2

280.0

500.0

255.0

235.0

475.0

442.0

94.2

16.0

11.0

18.0

[11.02]

[19.69]

[10.04]

[9.25]

[18.70]

[17.40]

[3.71]

[0.63]

[0.43]

[0.71]

D1*: Flange mounting

1-10

Chapter 1 IntroductionC2000 Series

Frame D0
D0-2: VFD370C43U; VFD450C43U;

D
W
W1

D1
D2

H

H3

H1

H2

SEE DETAIL A

S2

SEE DETAIL B

3

3

2

2

1

1

S1

S1

DETAIL A
(MOUNTING HOLE)

DETAIL B
(MOUNTING HOLE)
Unit: mm [inch]

Frame
D0-2

W

H

D

W1

H1

H2

H3

280.0 614.4 255.0 235.0 500.0 475.0 442.0

D1*

D2

S1

S2

Φ1

Φ2

Φ3

94.2

16.0

11.0

18.0

62.7

34.0

22.0

[11.02] [24.19] [10.04] [9.25] [19.69] [18.70] [17.40] [3.71] [0.63] [0.43] [0.71] [2.47] [1.34] [0.87]
D1*: Flange mounting

1-11

Chapter 1 IntroductionC2000 Series

Frame D
D1: VFD300C23A; VFD370C23A; VFD550C43A; VFD750C43A
D
W
W1

D1
D2

H3

H1

H2

SEE DETAIL A

S2
SEE DETAIL B

S1

S1

DETAIL A
(MOUNTING HOLE)

DETAIL B
(MOUNTING HOLE)

Unit: mm [inch]
Frame
D1

W

H

D

W1

H1

H2

H3

D1*

D2

S1

S2

330.0

-

275.0

285.0

550.0

525.0

492.0

107.2

16.0

11.0

18.0

[10.83] [11.22] [21.65] [20.67] [19.37] [4.22]

[0.63]

[0.43]

[0.71]

[12.99]

Φ1

Φ2

Φ3

-

-

-

D1*: Flange mounting

1-12

Chapter 1 IntroductionC2000 Series

Frame D
D2: VFD300C23E; VFD370C23E; VFD550C43E; VFD750C43E
D
W
W1

D1

H3

H1

D2

H

H2

SEE DETAIL A

S2

SEE DETAIL B

1

1

3

3

2

2

S1

S1

DETAIL A
(MOUNTING HOLE)

DETAIL B
(MOUNTING HOLE)

Unit: mm [inch]
Frame
D2

W

H

D

W1

H1

H2

H3

D1*

D2

S1

S2

Φ1

Φ2

Φ3

330.0

688.3

275.0

285.0

550.0

525.0

492.0

107.2

16.0

11.0

18.0

76.2

34.0

22.0

[12.99]

[27.10] [10.83] [11.22] [21.65]

[20.67] [19.37]

[4.22]

[0.63]

[0.43]

[0.71]

[3.00]

[1.34]

[0.87]

D1*: Flange mounting

1-13

Chapter 1 IntroductionC2000 Series

Frame E
E1: VFD450C23A; VFD550C23A; VFD750C23A; VFD900C43A; VFD1100C43A
W

D

W1

H3

H1

H2

D1

Unit: mm [inch]

Frame
E1

W
370.0
[14.57]

H
-

D

W1

300.0 335.0

H1
589

H2

H3

D1*

560.0 528.0 143.0

D2

S1, S2

S3

Ф1

Ф2

Ф3

18.0

13.0

18.0

-

-

-

[11.81] [13.19 [23.19] [22.05] [20.80] [5.63] [0.71] [0.51] [0.71]
D1*: Flange mounting

1-14

Chapter 1 IntroductionC2000 Series

Frame E
E2: VFD450C23E; VFD550C23E; VFD750C23E; VFD900C43E; VFD1100C43E
W

D

W1

H3

H1

?

?
?

?

?

?

?

?

H

H2

D1

Unit: mm [inch]

Frame
E2

W

H

D

W1

370.0 715.8 300.0 335.0

H1
589

H2

H3

D1*

560.0 528.0 143.0

D2

S1, S2

S3

Ф1

Ф2

Ф3

18.0

13.0

18.0

22.0

34.0

92.0

[14.57] [28.18] [11.81] [13.19 [23.19] [22.05] [20.80] [5.63] [0.71] [0.51] [0.71] [0.87] [1.34] [3.62]
D1*: Flange mounting

1-15

Chapter 1 IntroductionC2000 Series

Frame F
F1: VFD900C23A; VFD1320C43A; VFD1600C43A
W
W1

D
D1

H3

H2
H1

See Detail A

See Detail B

S3

D2

S1

S2
Detail A (Mounting Hole)

S1

Detail B (Mounting Hole)

Unit: mm [inch]

Frame

W

H

F1

420.0
[16.54]

-

D

W1

H1

H2

H3

300.0 380.0 800.0 770.0 717.0
[11.81] [14.96] [31.50] [30.32] [28.23]

D1*

D2

S1

S2

S3

124.0
[4.88]

18.0
[0.71]

13.0
[0.51]

25.0
[0.98]

18.0
[0.71]

D1*: Flange mounting

1-16

Chapter 1 IntroductionC2000 Series

Frame F
F2: VFD900C23E; VFD1320C43E; VFD1600C43E
W
W1

D
D1

H3

H

H2
H1

See Detail A

S3

See Detail B

D2

1
3
3
2

2

1

2

2

S1

S2
Detail A (Mounting Hole)

S1

Detail B (Mounting Hole)

Unit: mm [inch]

Frame
F2

W

H

D

W1

H1

H2

H3

420.0 940.0 300.0 380.0 800.0 770.0 717.0
[16.54] [37.00] [11.81] [14.96] [31.50] [30.32] [28.23]

Frame

Ф1

Ф2

Ф3

F2

92.0
[3.62]

35.0
[1.38]

22.0
[0.87]

D1*

D2

S1

S2

S3

124.0
[4.88]

18.0
[0.71]

13.0
[0.51]

25.0
[0.98]

18.0
[0.71]

D1*: Flange mounting

1-17

Chapter 1 IntroductionC2000 Series

Frame G
G1: VFD1850C43A; VFD2200C43A
W

D

H3

H1

H2

W1

S3

Unit: mm [inch]

Frame

W

H

G1

500.0
[19.69]

-

D

W1

H1

H2

H3

S1

397.0 440.0 1000.0 963.0 913.6 13.0
[15.63] [217.32] [39.37] [37.91] [35.97] [0.51]

1-18

S2

S3

Ф1

Ф2

Ф3

26.5
[1.04]

27.0
[1.06]

-

-

-

Chapter 1 IntroductionC2000 Series

Frame G
G2: VFD1850C43E; VFD2200C43E
W

D

H3

H1

H

H2

W1

S3

Unit: mm [inch]

Frame
G2

W

H

D

W1

H1

H2

H3

S1

500.0 1240.2 397.0 440.0 1000.0 963.0 913.6 13.0
[19.69] [48.83] [15.63] [217.32] [39.37] [37.91] [35.97] [0.51]

1-19

S2

S3

Ф1

Ф2

Ф3

26.5
[1.04]

27.0
[1.06]

22.0
[0.87]

34.0
[1.34]

117.5
[4.63]

Chapter 1 IntroductionC2000 Series

Frame H
H1: VFD2800C43A; VFD3150C43A; VFD3550C43A; VFD4500C43A

1-20

Chapter 1 IntroductionC2000 Series

Unit: mm [inch]

Frame
H1

Frame
H1

W
H
D
W1
W2
700.0 1435.0 398.0 630.0 290.0
[27.56] [56.5] [15.67] [24.8] [11.42]
H5
-

D1
45.0
[1.77]

W3

W4

W5

W6

-

-

-

-

D2

D3

D4

D5

D6

-

-

-

-

-

1-21

H1

H2
1346.6
1403.0
[55.24] [53.02]

S1
S2
S3
13.0 26.5 25.0
[0.51] [1.04] [0.98]

H3

H4

-

-

Ф1

Ф2

Ф3

-

-

-

Chapter 1 IntroductionC2000 Series

Frame H
H2: VFD2800C43E-1; VFD3150C43E-1; VFD3550C43E-1

Unit: mm [inch]

Frame
H2

Frame
H2

W
H
D
W1
W2
W3
W4
W5
700.0 1745.0 404.0 630.0 500.0 630.0 760.0 800.0
[27.56] [68.70] [15.91] [24.8] [19.69] [24.8] [29.92] [31.5]
H5
-

W6
-

H1
H2
1729.0 1701.6
[68.07] [66.99]

D1
D2
D3
D4
D5
D6
S1
S2
S3
51.0 38.0 65.0 204.0 68.0 137.0 13.0 26.5 25.0
[2.01] [1.50] [2.56] [8.03] [2.68] [5.39] [0.51] [1.04] [0.98]

1-22

H3

H4

-

-

Φ1

Φ2

Φ3

-

-

-

Chapter 1 IntroductionC2000 Series

Frame H
H3: VFD2800C43E; VFD3150C43E; VFD3550C43E

Unit: mm [inch]

Frame
H3

Frame
H3

W
H
D
W1
W2
W3
W4
W5
700.0 1745.0 404.0 630.0 500.0 630.0 760.0 800.0
[27.56] [68.70] [15.91] [24.8] [19.69] [24.8] [29.92] [31.5]
H5
-

W6
-

H1
H2
1729.0 1701.6
[68.07] [66.99]

H3

H4

-

-

D1
D2
D3
D4
D5
D6
S1
S2
S3
Φ1
Φ2
Φ3
51.0 38.0 65.0 204.0 68.0 137.0 13.0 26.5 25.0 22.0 34.0 117.5
[2.01] [1.50] [2.56] [8.03] [2.68] [5.39] [0.51] [1.04] [0.98] [0.87] [1.34] [4.63]

1-23

Chapter 1 IntroductionC2000 Series

Digital Keypad
KPC-CC01

1-24

Chapter 2 InstallationC2000 Series

Chapter 2 Installation
2-1 Minimum Mounting Clearance and Installation
NOTE

Prevent fiber particles, scraps of paper, shredded wood saw dust, metal particles, etc. from
adhereing to the heat sink

Install the AC motor drive in a metal cabinet. When installing one drive below another one,
use a metal separation between the AC motor drives to prevent mutual heating and to
prevent the risk of fire accident.

Install the AC motor drive in Pollution Degree 2 environments only: normallyl only
nonconductive pollution occurs and temporary conductivity caused by condensation is
expected.
The appearances shown in the following figures are for reference only.


Airflow direction:
(Blue arrow) inflow
(Red arrow) outflow
Single drive installation
Side-by-side horizontal installation(Frame A-C)
(Frame A-H)

Multiple drives, single side-by-side horizontal installation（Frame A~C, G, H）

2-1

Chapter 2 InstallationC2000 Series

Multiple drives, side-by-side installation (Frame D0, D, E, F) Install metal separation between the drives.

Multiple drives side-by-side vertical installation (Frame A~H )
Ta: Frame A~G
Ta*: Frame H
When installing one AC motor drive below another one (top-bottom installation), use a metal separation
between the drives to prevent mutual heating. The temperature measured at the fan’s inflow side must be
lower than the temperature measured at the operation side. If the fan’s inflow temperature is higher, use
a thicker or larger size of metal seperature. Operation temperature is the temperature measured at 50mm
away from the fan’s inflow side. (As shown in the figure below)

2-2 Minimum mounting clearance
Frame

A (mm)

B (mm)

C (mm)

D (mm)

A~C

60

30

10

0

D0~F

100

50

-

0

G

200

100

-

0

H

350

0

0

200 (100, Ta=Ta*=40℃)

VFD007C23A; VFD007C43A/E; VFD015C23A; VFD015C43A/E; VFD022C23A;
VFD022C43A/E; VFD037C23A; VFD037C43A/E; VFD040C43A/E; VFD055C43A/E;
VFD055C23A; VFD75C23A; VFD075C43A/E; VFD110C23A; VFD110C43A/E;
Frame B
VFD150C43A/E;
VFD150C23A; VFD185C23A; VFD185C43A/E; VFD220C23A; VFD220C43A/E;
Frame C
VFD300C43A/E;
Frame D0 VFD370C43S; VFD450C43S; VFD370C43U; VFD450C43U;
Frame D
VFD300C23A/E; VFD370C23A/E; VFD550C43A/E; VFD750C43A/E;
Frame A

2-2

Chapter 2 InstallationC2000 Series

Frame E
Frame F
Frame G
Frame H

VFD450C23A/E; VFD550C23A/E; VFD750C23A/E; VFD900C43A/E; VFD1100C43A/E;
VFD900C23A/E; VFD1320C43A/E; VFD1600C43A/E;
VFD1850C43A; VFD2200C43A; VFD1850C43E; VFD2200C43E;
VFD2800C43A; VFD3150C43A; VFD3550C43A; VFD4500C43A; VFD2800C43E-1;
VFD3150C43E-1; VFD3550C43E-1; VFD4500C43E-1; VFD2800C43E; VFD3150C43E;
VFD3550C43E; VFD4500C43E

NOTE

1. The minimum mounting clearances stated in the table above applies to AC motor drives frame A to D. A drive fails
to follow the minimum mounting clearances may cause the fan to malfunction and heat dissipation problem.

NOT E
※

The mounting clearances stated in the figure is for installing the drive in an
open area. To install the drive in a confined space (such as cabinet or
electric box), please follow the following three rules: (1) Keep the minimum
mounting clearances. (2) Install a ventilation equipment or an air conditioner
to keep surrounding temperature lower than operation temperature. (3)
Refer to parameter setting and set up Pr. 00-16, Pr.00-17, and Pr. 06-55.

※

The following table shows the heat dissipation and the required air
volume when installing a single drive in a confined space. When
installing multiple drives, the required air volume shall be multiplied
by the number the drives.

※

Refer to the chart (Air flow rate for cooling) for ventilation equipment
design and selection.

※

Refer to the chart (Power dissipation) for air conditioner design and
selection.

※

Different control mode will affect the derating. See Pr06-55 for more
information.

※

Ambient temperature derating curve shows the derating status in
different temperature in relation to different protection level.

※

If UL Type 1 models need side by side installation, please remove top
cover of FrameA~C, and please do not install conduit box of Frame D
and above.

Air flow rate for cooling
Flow Rate (cfm)
Model No.
VFD007C23A
VFD015C23A
VFD022C23A
VFD037C23A
VFD055C23A
VFD075C23A
VFD110C23A
VFD150C23A
VFD185C23A
VFD220C23A

External Internal
14
14
10
40
66
58
166
166
166

14
14
14
12
12
12

Total
14
14
10
54
80
73
178
178
178

Flow Rate (m3/hr)
External Internal
24
24
17
68
112
99
282
282
282

24
24
24
20
20
20

2-3

Total
24
24
17
92
136
124
302
302
302

Power dissipation of AC motor
drive
Power Dissipation
Loss External
Internal
Total
(Heat sink)
33
27
61
56
31
88
79
36
115
113
46
159
197
67
264
249
86
335
409
121
529
455
161
616
549
184
733
649
216
865

Chapter 2 InstallationC2000 Series

Air flow rate for cooling
Flow Rate (cfm)
Model No.

External Internal

Total

Flow Rate (m3/hr)
External Internal

Total

VFD300C23A/E
VFD370C23A/E
VFD450C23A/E
VFD550C23A/E
VFD750C23A/E
VFD900C23A/E

179
179
228
228
246
224

30
30
73
73
73
112

209
209
301
301
319
336

304
304
387
387
418
381

51
51
124
124
124
190

355
355
511
511
542
571

VFD007C43A/E
VFD015C43A/E
VFD022C43A/E
VFD037C43A/E
VFD040C43A/E
VFD055C43A/E
VFD075C43A/E
VFD110C43A/E
VFD150C43A/E
VFD185C43A/E
VFD220C43A/E
VFD300C43A/E
VFD370C43A/E
VFD450C43A/E
VFD550C43A/E
VFD750C43A/E
VFD900C43A/E
VFD1100C43A/E
VFD1320C43A/E
VFD1600C43A/E
VFD1850C43A/E
VFD2200C43A/E

14
10
10
10
40
66
58
99
99
126
179
179
179
186
257
223
224
289

14
14
14
21
21
21
30
30
30
30
73
73
112
112

14
10
10
10
54
80
73
120
120
147
209
209
209
216
330
296
336
401
454
454

24
17
17
17
68
112
99
168
168
214
304
304
304
316
437
379
381
491

24
24
24
36
36
36
51
51
51
51
124
124
190
190

24
17
17
17
92
136
124
204
204
250
355
355
355
367
561
503
571
681
771
771

Power dissipation of AC motor
drive
Power Dissipation
Loss External
Internal
Total
(Heat sink)
913
186
1099
1091
220
1311
1251
267
1518
1401
308
1709
1770
369
2139
2304
484
2788
33
45
71
103
116
134
216
287
396
369
476
655
809
929
1156
1408
1693
2107
2502
3096

25
29
33
38
42
46
76
93
122
138
158
211
184
218
257
334
399
491
579
687

59
74
104
141
158
180
292
380
518
507
635
866
993
1147
1413
1742
2092
2599
3081
3783
4589
5772

VFD2800C43A/E

769

1307

6381

VFD3150C43A/E

769

1307

7156

VFD3550C43A/E

769

1307

8007

VFD4500C43A/E
769
1307
※ The required airflow shown in chart is for installing single drive in a
confined space.
※ When installing the multiple drives, the required air volume should
be the required air volume for single drive X the number of the
drives.

※

※

※

2-4

11894
The heat dissipation shown in
the chart is for installing single
drive in a confined space.
When installing the multiple
drives, volume of heat
dissipation should be the heat
dissipated for single drive X
the number of the drives.
Heat dissipation for each
model is calculated by rated
voltage, current and default
carrier.

Chapter 2 InstallationC2000 Series
NOTE

Normal control Ambient temperature derating curve

Advanced control Ambient temperature derating curve

2-5

Chapter 3 UnpackingC2000 Series

Chapter 3 Unpacking
The AC motor drive should be kept in the shipping carton or crate before installation. In order to retain the
warranty coverage, the AC motor drive should be stored properly when it is not to be used for an extended
period of time.

3-1 Unpacking
The AC motor drive is packed in the crate. Follows the following step for unpack:
Frame D
Crate 1 (VFDXXXCXXA)
Crate 2 (VFDXXXCXXE)
Loosen the 12 cover screws to open the crate.
Loosen the 4 screws on the iron plates. There are 4
iron plates and in total of 16 screws.

Remove the EPEs and manual.

Remove the crate cover, EPEs, rubber and
manual.

Loosen the 8 screws that fastened on the pallet
and remove the wooden plate.

3-1

Chapter 3 UnpackingC2000 Series

Lift the drive by hooking the lifting hole. It is now
ready for installation.

Loosen the 10 screws on the pallet, remove the
wooden plate.

Lift the drive by hooking the lifting hole. It is now
ready for installation.

Frame E
Crate 1 (VFDXXXCXXA)
Crate 2 (VFDXXXCXXE)
Loosen the 4 screws on the iron plates. There are 4 Loosen the 4 screws on the iron plates. There are
iron plates and in total of 16 screws.
4 iron plates and in total of 16 screws.

3-2

Chapter 3 UnpackingC2000 Series

Remove the crate cover, EPEs and manual.

Remove the crate cover, EPEs, rubbers and
manual.

Loosen the 8 screws on the pallet as shown in the
following figure.

Loosen the 10 screws on the pallet and remove the
wooden plate.

Lift the drive by hooking the lifting hole. It is now
ready for installation.

Lift the drive by hooking the lifting hole. It is now
ready for installation.

3-3

Chapter 3 UnpackingC2000 Series

Frame F
Crate 1 (VFDXXXCXXA)
Remove the 6 clips on the side of the crate with a
flat-head screwdriver. (As shown in figure below.)

Crate 2 (VFDXXXCXXE)
Remove the 6 clips on the side of the crate with a
flat-head screwdriver. (As shown in figure below.)

6

6

5

5

4

4
1

1

2

2

3

3
Remove the crate cover, EPEs and manual.

Remove the crate cover, EPEs, rubbers and
manual.

Loosen the 5 screws on the pallet
as shown in the following figure.

Loosen the 9 screws on the pallet and remove the
wooden plate.

5

9

4
3

wood plate2

2

wood plate1

1

3-4

8

7

6

5

4

3

2

1

Chapter 3 UnpackingC2000 Series

Lift the drive by hooking the lifting hole. It is now
ready for installation

Lift the drive by hooking the lifting hole. It is now
ready for installation.

.
Frame G
Crate 1 (VFDXXXCXXA)
Crate 2 (VFDXXXCXXE)
Remove the 6 clips on the side of the crate with a Remove the 6 clips on the side of the crate with a
flathead screwdriver. (As shown in figure below.)
flathead screwdriver. (As shown in figure below.)
4

4

5

5

6

6

1

1
2

2
3

Remove the crate cover, EPEs and manual.

3

Remove the crate cover, EPEs, rubber and manual.

3-5

Chapter 3 UnpackingC2000 Series

Loosen the 5 screws as shown in following figure:
3

Loosen the 12 screws and remove the wooden
plate.

4

11 5 4
6

5

12

1

wood plate5
wood plate4

98
10

3

7
wood plate1
wood plate2
wood plate3

1

2

2

Lift the drive by hooking the lifting hole. It is now
ready for installation.

Lift the drive by hooking the lifting hole. It is now
ready for installation.

Frame H
Crate 1 (VFDXXXC43A)
Crate 2 (VFDXXXC43E-1)
Remove the 8 clips on the side of the crate with a Remove the 8 clips on the side of the crate with a
flathead screwdriver. (As shown in figure below.)
flathead screwdriver. (As shown in figure below.)

3-6

Chapter 3 UnpackingC2000 Series

Remove the crate cover, EPEs and manual.

Remove the crate cover, EPEs, rubbers and
manual.

Loosen the 6 screws on the top then remove 6
metal washers and 6 plastic washers as shown in
figure below.

Loosen the 6 screws on the top then remove 6
metal washers and 6 plastic washers as shown in
figure below.

Lift the drive by hooking the lifting hole. It is now
ready for installation.

Loosen 6 of the M6 screws on the side and remove
the 2 plates, as shown in below. The removed
screws and plates can be used to secure the AC
motor drive from the external.

3-7

Chapter 3 UnpackingC2000 Series

Secure the drive from the external. (Skip to the
next step if this situation does not apply to you.)
Loosen 8 of M8 screws on the both sides and place
the 2 plates that were removed from the last step.
Fix the plates to AC motor drive by fasten 8 of the
M8 screws. (As shown in below)
Torque: 150~180kg-cm (130.20~156.24lb-in.)

Lift the drive by hooking the lifting hole. It is now
ready for installation.

Frame H
Crate 3 (VFDXXXC43E)
Use flathead screwdriver to remove the clips on the side of the crate, 8 clips in total.

3-8

Chapter 3 UnpackingC2000 Series

Remove the crate cover, EPEs, rubber and manual.

Loosen the 6 screws on the cover, remove 6 metal washers and 6 plastic washers as shown in below:

Loosen 6 of the M6 screws on the side and removes the 2 plates, as shown in following figure. The
removed screws and plates can be used to secure AC motor drive from the external.

3-9

Chapter 3 UnpackingC2000 Series

Secure the drive from the internal.
Loosen 18 of the M6 screws and remove the top
cover as shown in figure 2. Mount the cover (figure
1) back to the drive by fasten the M6 screws to the
two sides of the drive, as shown in figure 2.
Torque: 35~45kg-cm (30.38~39.06lb-in.)

Secure the drive from the external.
Loosen 8 of the M8 screws on the both sides and
place the 2 plates that were removed from the last
step. Fix the plates to rive by fasten 8 of the M8
screws. (As shown in figure below).
Torque: 150~180kg-cm (130.20~156.24lb-in.)

Figure 1
Top cover (Use M12 screws)

Figure 2
Fasten 6 of the M6 screws back to the original position where it was removed. As shown in the figure:

3-10

Chapter 3 UnpackingC2000 Series

Lift the drive by hooking the lifting hole. It is now ready for installation.

Frame H Secure the drive
(VFDXXXC43A)
Screw: M12*6

Torque: 340-420kg-cm [295.1-364.6lb-in.]

3-11

Chapter 3 UnpackingC2000 Series

(VFDXXXC43E) & (VFDXXXC43E-1)

Secure the drive from the internal.
Screw: M12*8
Torque: 340-420kg-cm [295.1-364.6lb-in.]

Secure the drive from the external.
Screw: M12*8
Torque: 340-420kg-cm [295.1-364.6lb-in.]

3-12

Chapter 3 UnpackingC2000 Series

3-2 The Lifting Hook
The arrows indicate the location of the lifting holes of frame D to H, as shown in figure below:

D0

E

D

Figure 1

Figure 2

Figure 3

G

F

Figure 4

Figure 5

3-13

Figure 6

Chapter 3 UnpackingC2000 Series

Ensure the lifting hook properly goes through the
lifting hole, as shown in the following diagram.
(Applicable to Frame D0~E)

Ensure the angle between the lifting holes and the
lifting device is within the specification, as shown
in the following figure. (Applicable to Frame D0~E)

(Applicable to Frame F~H)

(Applicable to Frame F~H)

3-14

Chapter 3 UnpackingC2000 Series

Weight
VFDXXXXCXXA
27 kg(59.5 Ibs.)

37.6 kg(82.9 Ibs.)

63.6 kg(140.2 Ibs.)

VFDXXXXCXXE
29 kg(63.9 Ibs.)

40 kg(88.2 Ibs.)

66 kg(145.5 Ibs.)

88kg(193.8 Ibs.)

85kg(187.2 Ibs.)

130kg(286.5 Ibs.)

H1: VFD2800C43A; VFD3150C43A; VFD3550C43A; VFD4500C43A

235kg (518.1lbs)

H2: VFD2800C43E-1; VFD3150C43E-1; VFD3550C43E-1; VFD4500C43E-1

H3: VFD2800C43E; VFD3150C43E; VFD3550C43E; VFD4500C43E

3-15

257kg (566.6lbs)

263kg (579.8lbs)

Chapter 4 WiringC2000 Series

Chapter 4 Wiring
After removing the front cover, examine if the power and control terminals are clearly noted. Please read
following precautions before wiring.
 Make sure that power is only applied to the R/L1, S/L2, T/L3 terminals. Failure to comply may result
in damage to the equipments. The voltage and current should lie within the range as indicated on the
nameplate (Chapter 1-1).
 All the units must be grounded directly to a common ground terminal to prevent lightning strike or
electric shock.
 Please make sure to fasten the screw of the main circuit terminals to prevent sparks which is made
by the loose screws due to vibration
 It is crucial to turn off the AC motor drive power before any wiring installation are
made. A charge may still remain in the DC bus capacitors with hazardous voltages

DANGER

even if the power has been turned off therefore it is suggested for users to measure
the remaining voltage before wiring. For your personnel saftery, please do not
perform any wiring before the voltage drops to a safe level < 25 Vdc. Wiring
installation with remaninig voltage condition may caus sparks and short circuit.
 Only qualified personnel familiar with AC motor drives is allowed to perform
installation, wiring and commissioning. Make sure the power is turned off before
wiring to prevent electric shock.
 When wiring, please choose the wires with specification that complys with local
regulation for your personnel safety.
 Check following items after finishing the wiring:
1.

Are all connections correct?

2.

Any loosen wires?

3.

Any short-circuits between the terminals or to ground?

4-1

Chapter 4 WiringC2000 Series

4-1 Wiring

4-2

Chapter 4 WiringC2000 Series

4-3

Chapter 4 WiringC2000 Series

Figure 1 (For Frame G and above)
Power



Transformer



VFD-C2000

R / L11
S /L21

R
S

T/ L31

T

DC+
R / L12
S /L22
T/ L32
DC-

Figure 2
SINK（NPN）/SOURCE（PNP）Mode
Sourc e Mode
w ith internal power (+24VD C)

MI1

MI1

MI2

MI2

~

2

~

1 Sink Mode
with internal power (+24VDC )

MI8

MI8

+2 4V

DCM

COM

COM

DCM

internal c irc ui t

3 Sink Mode
with external power

+2 4V

4 Sourc e Mode
with external power

MI2

MI2

~

MI1

~

MI1

MI8

MI8

+2 4V

+2 4V

COM

COM

DCM

external power +24V

internal c irc ui t

DCM

internal c irc ui t

external pow er +24V

4-4

internal c irc ui t

Chapter 4 WiringC2000 Series

Figure 3
Function of DC Link
 Applicable to Frame E~H
 Operation Instruction
1. When RST power is off, please disconnect terminal r and terminal s. (As circled in dotted line,
uninstall the gray section and properly store cable r and cable s. Cable r and cable s are not
available in optional accessories, do not dispose them.)
After terminal r and terminal s are cleared, user may now connect new power source to terminal r
and terminal s. Please connect 220Vac for 220V model and 440 Vac for 440V model.
When the drive power is on, if terminal r and terminal s are not connected to new power source
(220 Vac for 220V model and 440Vac for 440 V model), the digital keypad will display an error
message “ryF”.
2. When DC Link is used as a DC Bus connection (RST power is applied), it is not required to
remove terminal r and terminal s.
NOTE

Common DC Bus can only be applied to the drives with same power range. If in your case the
drives are in different power range, please contact with us (Delta Industrial Automation Business
Unit).

r s

4-5

Chapter 4 WiringC2000 Series

4-2 System Wiring Diagram
Power input terminal
Power input
terminal
NFB or fuse

There may be a large inrush current during
NFB or fuse power on. Refer to 7-2 NFB to select a suitable
NFB or fuse.

Electromagnetic
contactor
AC reactor
(input terminal)

Electromagnetic
contactor

Zero-phase
reactor

+

B1

B2
U/T1 V/T2 W/T3

AC reactor
(input terminal)

BR
VFDB
BR

R/L1 S/L2 T/L3 E

Brake
resistor

EMI filter

E
Zero-phase
reactor

Motor

Switching ON/OFF the primary side of the
electromagnetic contactor can turn the integrated
elevator device ON/OFF, but frequent switching is
a cause of machine failure. Do not switch ON/OFF
more than once an hour. Do not use the
electromagnetic contactor as the power switch
for the integrated elevator drive; doing so will
shorten the life of the integrated elevator drive.
When the main power supply capacity is
greater than 500kVA, or when it switches
into the phase capacitor, the instantaneous
peak voltage and current generated will
destroy the internal circuit of the integrated
elevator drive. It is recommended to install
an input side AC reactor in the integrated
elevator drive. This will also improve the
power factor and reduce power harmonics.
The wiring distance should be within 10m.
Please refer to 7-4.

Used to reduce radiated interference, especially
in environments with audio devices, and reduce
Zero-phase
input and output side interference.
reactor
The effective range is AM band to 10MHz.
Please refer to Appendix 7-5.
Can be used to reduce electromagnetic
interference.

EMI filter
AC reactor
(output terminal)

Please supply power according to the rated
power specifications indicated in the manual
(refer to 9 Specifications Table).

Brake resistor Used to shorten deceleration time of the motor.
Please refer to 7-1.
The wiring length of the motor will affect the size
of the reflected wave on the motor end. It is
AC reactor
(output terminal) recommended to install an AC reactor when the
motor wiring length is greater than 20 meters.
Refer to 7-4.

4-6

Chapter 5 Main Circuit TerminalsC2000 Series

Chapter 5 Main Circuit Terminals
5-1 Main Circuit Diagram
For frame A~C
* Provid e 3-ph ase inpu t power

Brake resis tor
(optio nal)
Jumper

Fus e/NFB(No F use Bre aker)

-

+1

+2

B1

B2
U(T1)

R(L1)
R(L1)
S(L2)
T(L3)

S(L2)

V(T2)

T(L3)

W(T3)

For frame A~C
* Provide 3-phase i nput power
F us e/NF B(No F use B reaker)

DC choke
(optional)
J umper

-

+2

+1

R(L1)
R(L1)
S(L2)
T(L3)

Mo tor

IM
3~

Br ak e r es istor
(optional)

B1

B2
U(T 1)

S(L2)

V(T2)

T(L3)

W(T 3)

Motor

IM
3~

For frame D0 and above D0
* Provide 3-phase input power
Fuse/NFB(No Fuse Breaker)

+1/DC+

R(L1)

U(T1)

R(L1)
S(L2)
T(L3)

-/DC-

S(L2)

V(T2)

T(L3)

W(T3)

5-1

Motor

IM
3~

Chapter 5 Main Circuit TerminalsC2000 Series

For Frame G and above
Power



Transformer

R
S

R / L11
S /L21

T

T/ L31



VFD-C2000

DC+
R / L12
S /L22
T/ L32
DC-



NOTE
Please remove short circuit plate of FRAME G and H if 12 pulse is implemented



Before implementing 12 pulse, consult Delta for more detail

Terminals

Descriptions

R/L1, S/L2, T/L3

AC line input terminals 3-phase

U/T1, V/T2, W/T3

AC drive output terminals for connecting 3-phase induction motor
Applicable to frame A~C

+1, +2

Connections for DC reactor to improve the power factor. It needs to remove the
jumper for installation.
Connections for brake unit (VFDB series)

+1/DC+, -/DC-

(for 230V models: ≦22kW, built-in brake unit)
(for 460V models: ≦30kW, built-in brake unit)
Common DC Bus

B1, B2

Connections for brake resistor (optional)
Earth connection, please comply with local regulations.

5-2

Chapter 5 Main Circuit TerminalsC2000 Series

Main power terminals


Do not connect 3-phase model to one-phase power. R/L1, S/L2 and T/L3
has no phase-sequence requirement, it can be used upon random
selection.



It is recommend to add a magnetic contactor (MC) to the power input wiring
to cut off power quickly and reduce malfunction when activating the
protection function of the AC motor drive. Both ends of the MC should have
an R-C surge absorber.



Fasten the screws in the main circuit terminal to prevent sparks condition
made by the loose screws due to vibration.



Please use voltage and current within the specification.



When using a general GFCI (Ground Fault Circuit Interrupter), select a
current sensor with sensitivity of 200mA or above and not less than
0.1-second operation time to avoid nuisance tripping.



Please use the shield wire or tube for the power wiring and ground the two
ends of the shield wire or tube.



Do NOT run/stop AC motor drives by turning the power ON/OFF. Run/stop
AC motor drives by RUN/STOP command via control terminals or keypad. If
you still need to run/stop AC motor drives by turning power ON/OFF, it is
recommended to do so only ONCE per hour.

Output terminals for main circuit


When it needs to install the filter at the output side of terminals U/T1, V/T2,
W/T3 on the AC motor drive. Please use inductance filter. Do not use
phase-compensation capacitors or L-C (Inductance-Capacitance) or R-C
(Resistance-Capacitance), unless approved by Delta.



DO NOT connect phase-compensation capacitors or surge absorbers at the
output terminals of AC motor drives.



Use well-insulated motor, suitable for inverter operation.



Note down the rated data and the torque force of the wiring when the output
terminal is below 75℃.

This information provides the right wiring method

to wire terminals (It corresponds to the terminals of the motor wire and
non-motor wire).


When the AC drive output terminals U/T1, V/T2, and W/T3 are connected to
the motor terminals U/T1, V/T2, and W/T3, respectively, the motor will rotate
counterclockwise (as viewed on the shaft end of the motor) when a forward
operation command is received. To permanently reverse the direction of
motor rotation, switch over any of the two motor leads

Fo wa rd
Running

5-3

Chapter 5 Main Circuit TerminalsC2000 Series

Terminals for connecting DC reactor, external brake resistor, external
brake resistor and DC circuit


This is the terminals used to connect the DC reactor to improve the power
factor. For the factory setting, it connects the short-circuit object. Please
remove this short-circuit object before connecting to the DC reactor.
DC rea ct or (o ption al)
+1



+2

Connect a brake resistor or brake unit in applications with frequent
deceleration ramps, short deceleration time, too low brake torque or
requiring increased brake torque.
Brak e re sistor
(optional)

Brak e re sistor
(optional)

BR

Brak e un it
(o ption al)

VFDB

B2

B1



+

-

The external brake resistor of Frame A, B and C should connect to the
terminals (B1, B2) of AC motor drives.



For those models without built-in brake resistor, please connect external
brake unit and brake resistor (both of them are optional) to increase brake
torque.



When the terminals +1, +2 and - are not used, please leave the terminals
open.



DO NOT connect [+1, -], [+2, -], [+1/DC+, -/DC-] or brake resistor directly to
prevent drive damage.



DC+ and DC- are connected by common DC bus, please refer to Chapter
5-1(Main Circuit Terminal) for the wiring terminal specification and the wire
gauge information.



Please refer to the VFDB manual for more information on wire gauge when
installing the brake unit.

5-4

Chapter 5 Main Circuit TerminalsC2000 Series

5-2 Main Circuit Terminals
Frame A

Main circuit terminals:
R/L1, S/L2, T/L3, U/T1, V/T2, W/T3,
Models

Max. Wire
Gauge

, B1, B2, +1, +2, -

Min. Wire Gauge

Torque
(±10%)

14 AWG (2.1mm2)
VFD007C23A
VFD015C23A
12 AWG (3.3mm2)
VFD022C23A
10 AWG (5.3mm2)
VFD037C23A
8 AWG (8.4mm2)
VFD007C43A
14 AWG (2.1mm2)
VFD007C43E
14 AWG (2.1mm2)
VFD015C43A
14 AWG (2.1mm2)
M4
VFD015C43E
14 AWG (2.1mm2)
8 AWG
20kg-cm
(8.4mm2)
(17.4 lb-in.)
VFD022C43A
14 AWG (2.1mm2)
(1.962Nm)
VFD022C43E
14 AWG (2.1mm2)
2
VFD037C43A
10 AWG (5.3mm )
VFD037C43E
10 AWG (5.3mm2)
VFD040C43A
10 AWG (5.3mm2)
VFD040C43E
10 AWG (5.3mm2)
VFD055C43A
10 AWG (5.3mm2)
VFD055C43E
10 AWG (5.3mm2)
UL installations must use 600V, 75℃ or 90℃ wire. Use copper wire
only.
1. Figure 1 shows the terminal specification.
2. Figure 2 shows the specification of insulated heat shrink tubing that
comply with UL (600V, YDPU2).
Figure 1
Figure 2

5-5

Chapter 5 Main Circuit TerminalsC2000 Series

Frame B

Main circuit terminals:
R/L1, S/L2, T/L3, U/T1, V/T2, W/T3,
Models

Max. Wire
Gauge

, B1, B2, +1, +2, -

Min. Wire Gauge

Torque
(±10%)

VFD055C23A
8 AWG (8.4mm2)
VFD075C23A
6 AWG (13.3mm2)
VFD110C23A
4 AWG (21.2mm2)
M5
VFD075C43A
8 AWG (8.4mm2)
35kg-cm
4 AWG
(30.4 lb-in.)
VFD075C43E
8AWG (8.4mm2)
(21.2mm2)
(3.434Nm)
VFD110C43A
8 AWG (8.4mm2)
2
VFD110C43E
8 AWG (8.4mm )
VFD150C43A
6 AWG (13.3mm2)
VFD150C43E
6 AWG (13.3mm2)
UL installations must use 600V, 75℃ or 90℃ wire. Use copper wire
only.
NOTE

Terminal D+ [+2 & +1]: Torque: 45 kg-cm [39.0lb-in.] (4.415Nm) (±10%)
1. VFD110C23A must use 600V, 90℃ wire when surrounding
temperature exceeds 45℃.
2. Figure 1 shows the terminal specification.
3. Figure 2 shows the specification of insulated heat shrink tubing that
comply with UL (600V, YDPU2).
Figure 1
Figure 2

5-6

Chapter 5 Main Circuit TerminalsC2000 Series

Frame C

Main circuit terminals:
R/L1, S/L2, T/L3, U/T1, V/T2, W/T3,
Models

Max. Wire
Gauge

, B1, B2, +1, +2, -

Min. Wire Gauge

Torque
(±10%)

VFD150C23A
1 AWG (42.4mm2)
VFD185C23A
1/0 AWG (53.5mm2)
VFD220C23A
1/0 AWG (53.5mm2)
M8
VFD185C43A
4 AWG (21.2mm2)
1/0 AWG
80kg-cm
VFD185C43E
4 AWG (21.2mm2)
(53.5mm2)
(69.4 lb-in.)
VFD220C43A
4 AWG (21.2mm2)
(7.85Nm)
2
VFD220C43E
4 AWG (21.2mm )
VFD300C43A
2 AWG (33.6mm2)
VFD300C43E
2 AWG (33.6mm2)
UL installations must use 600V, 75℃ or 90℃ wire. Use copper wire
only.
NOTE

Terminal D+ [+2 & +1]: Torque: 90 kg-cm [78.2lb-in.] (8.83Nm) (±10%)
1. VFD220C23A must use 600V, 90℃ wire when surrounding
temperature exceeds 40℃.
2. Figure 1 shows the terminal specification.
3. Figure 2 shows the specification of insulated heat shrink tubing that
comply with UL (600V, YDPU2).
Figure 1
Figure 2

c

5-7

Chapter 5 Main Circuit TerminalsC2000 Series

Main circuit terminals:
R/L1, S/L2, T/L3, U/T1, V/T2, W/T3,

, +1/DC+, -/DC-

Torque
(±10%)
1/0 AWG (53.5mm2)
VFD370C43S
M8
VFD450C43S
2/0 AWG 2/0 AWG (67.4mm2)
80kg-cm
(67.4mm2) 1/0 AWG (53.5mm2)
(70 lb-in.)
VFD370C43U
2
(7.85Nm)
VFD450C43U
1/0 AWG (53.5mm )
UL installations must use 600V, 75℃ or 90℃ wire. Use copper wire
only.
Specification of grounding wire: 2AWG*2(33.6mm2*2)
Figure on the right shows the specification of insulated heat shrink
tubing that comply with UL (600V, YDPU2).
Models

Min. Wire Gauge

11 Max.

Max. Wire
Gauge

+0
-2

22 Max.
8.2 Min.

8.2 Min.
Ring lug

13±1.5

32 Max.

Ring lug

13 Min.

13 Min.

Frame D0

Heat Shrink Tube
WIRE

5-8

Heat Shrink Tube
WIRE

Chapter 5 Main Circuit TerminalsC2000 Series

Main circuit terminals:
R/L1, S/L2, T/L3, U/T1, V/T2, W/T3,
Max. Wire
Gauge

Models

, +1/DC+, -/DC-

Min. Wire Gauge

Torque
(±10%)

4/0 AWG (107mm2)
VFD300C23A
VFD370C23A
250MCM (127mm2)
300MCM
2
(152mm )
VFD550C43A
3/0 AWG (85mm2)
VFD750C43A
300MCM (152mm2)
M8
VFD300C23E
3/0 AWG (85mm2)
200kg-cm
(173 lb-in.)
VFD370C23E
4/0 AWG (107mm2)
2
(19.62Nm)
VFD370C43E
1/0 AWG (53.5mm )
4/0 AWG.
2
2
(107mm )
VFD450C43E
1/0 AWG (53.5mm )
VFD550C43E
2/0 AWG (67.4mm2)
VFD750C43E
4/0 AWG (107mm2)
1. UL installations must use 600V, 75oC or 90 oC wires. Use copper
wire only.
2. Figure 1 shows the terminal specification.
3. Figure 2 shows the specification of insulated heat shrink tubing
that comply with UL (600V, YDPU2).
Figure 1
17 Max.

Figure 2

28 Max.
8.2 Min.
Ring lug
48 Max.

Frame D

28 Max.

5-9

Chapter 5 Main Circuit TerminalsC2000 Series

Frame E

Main circuit terminals:
R/L1, S/L2, T/L3, U/T1, V/T2, W/T3,
Models

Max. Wire
Gauge

, +1/DC+, -/DC-

Min. Wire Gauge

VFD450C23A

1/0AWG*2 (53.5mm2*2)

VFD550C23A

3/0AWG*2 (85mm2*2)

VFD750C23A
VFD900C43A

300MCM*2
4/0 AWG*2 (107mm2*2)
(152mm2*2)
1/0AWG*2 (53.5mm2*2)

Incorrect installation may
result in damage to option
or inverter.Please refer to
operation manual for
installation instructions.

VFD1100C43A

3/0AWG*2 (85mm2*2)

VFD450C23E

1/0AWG*2 (53.5mm2*2)

VFD550C23E

2/0AWG*2 (67.4mm2*2)

VFD750C23E

4/0 AWG*2
(107mm2*2)

M8
200kg-cm
(173 lb-in.)
(19.62Nm)

3/0AWG*2 (85mm2*2)

VFD900C43E

1/0AWG*2 (53.5mm2*2)

VFD1100C43E

2/0AWG*2 (67.4mm2*2)

UL installations must use 600V, 75oC or 90 oC wires. Use copper
wire only.
2. Specification of grounding wire : 300MCM [152 mm2]
Torque: M8 180kg-cm (156 lb-in.) (17.64Nm) (±10%), as shown in
Figure 2.
3. Figure 1 shows the specification for ring lug.
4. Figure 3 shows the specification of insulated heat shrink tubing
that comply with UL (600C, YDPU2).
E
Figure 1
Figure 2
17.0MAX.

31MAX.
8. 2M I

26.5MAX.
Figure 3

5-10

28.0MAX.

N.
65.0MAX.

16-4

+0

1.

70MAX.

警
告
錯誤的安裝將會導
致變頻器及選配品
損壞，安裝前請務
必參閱使用手冊後
才進行裝配。

Torque
(±10%)

8.2MIN

.

Chapter 5 Main Circuit TerminalsC2000 Series

Main circuit terminals:
R/L1, S/L2, T/L3, U/T1, V/T2, W/T3, +1/DC+, -/DCModels

Max. Wire
Gauge

Min. Wire Gauge

Torque
(±10%)

300MCM*2 (152mm2*2)

VFD900C23A

300MCM*2
4/0 AWG*2 (107mm2*2)
(152mm2*2)
VFD1600C43A
300MCM*2 (152mm2)
VFD1320C43A

M8
200kg-cm
4/0 AWG*2 (107mm2*2) (173 lb-in.)
VFD900C23E
(19.62Nm)
4/0 AWG*2
VFD1320C43E
3/0AWG*2 (85mm2*2)
2
(107mm *2)
VFD1600C43E
4/0 AWG*2 (107mm2*2)
1.
2.

VFD900C23A/E installations must use 90℃ wire.
For other model, UL installations must use 600V, 75℃ or 90℃
wire. Use copper wire only.

Specification of grounding wire
：300MCM*2 [152 mm2*2]
Torque: M8 200kg-cm (173 lb-in.) (19.62Nm) (±10%)
5. Figure 1 shows the specification for ring lug.
4. Figure 2 shows the specification of insulated heat shrink tubing
that comply with UL (600C, YDPU2).
Figure 1
Figure 2

16-4

+0

3.

70MAX.

Frame F

31MAX.
8.2MI
N.

26.5MAX.

5-11

Chapter 5 Main Circuit TerminalsC2000 Series

Main circuit terminals:
R/L11, R/L12, S/L21, S/L22, T/L31, T/L32
Models

Max. Wire
Gauge

Min. Wire Gauge

Torque
(±10%)

2/0AWG*4 (67.4mm2*4)

VFD1850C43A

M8
VFD2200C43A 300MCM*4 3/0AWG*4 (85mm2*4) 200kg-cm
2
VFD1850C43E (152mm *4) 1/0AWG*4 (53.5mm2*4) (173 lb-in.)
(19.62Nm)
VFD2200C43E
2/0AWG*4 (67.4mm2*4)

Main circuit terminals:
U/T1, V/T2, W/T3, +1/DC+, -/DCMax. Wire
Models
Min. Wire Gauge
Gauge
400MCM*2 (203mm2*2)
VFD1850C43A

Torque
(±10%)

M12
VFD2200C43A 500MCM*2 500MCM*2 (253mm2*2) 408kg-cm
2
VFD1850C43E (253mm *2) 300MCM*2 (152mm2*2) (354lb-in.)
( 40Nm)
VFD2200C43E
400MCM*2 (203mm2*2)
UL installations must use 600V, 75℃ or 90℃ wire. Use copper
wire only.
Use 600V, 90℃ wire for VFD2200C43A when the surrounding
temperature is over 45℃.
Figure 1 and Figure 2 show the specification for using ring lug.

1.
2.
3.

Specification for grounding wire : 300MCM*4 [152 mm2*2]
Torque: M8 200kg-cm (173 lb-in.) (19.62Nm) (±10%), as shown
in Figure 1
5. Figure 3 and Figure 4 shows the specification of insulated heat
shrink tubing that comply with UL (600C, YDPU2).
Figure 1
Figure2
R/L11, R/L12, S/L21, S/L22, U/T1, V/T2, W/T3, +1/DC+, -/DCT/L31, T/L32,

31MAX.
8.2MI
N.

42.0(MAX.)

12.2(MIN.)

42.0(MAX.)
70.0(MAX.)

26.5MAX.

21.0(MAX.)

16-4

+0

4.

54MAX.

Frame G

Figure 3

Figure 4

5-12

Chapter 5 Main Circuit TerminalsC2000 Series

Frame H

Main circuit terminals:
R/11,R12,S/21,S/22,T/31,T/32, U/T1,V/T2, W/T3, +1/DC+, -/DCModels

Max. Wire
Gauge

Min. Wire Gauge

VFD2800C43A

4/0 AWG*4 (107mm2*4)

VFD3150C43A

300MCM*4 (152mm2*4)

VFD3550C43A

300MCM*4 (152mm2*4)

VFD4500C43A

300MCM*4 (152mm2*4)

VFD2800C43E-1

3/0 AWG*4 (85mm2*4)

Torque
(±10%)

M8
200kg-cm
VFD3150C43E-1 300MCM*4 4/0 AWG*4 (107mm *4)
(173 lb-in.)
2
VFD3550C43E-1 (152mm *4) 250MCM*4 (127mm2*4) (19.62Nm)
2

VFD4500C43E-1

300MCM*4 (152mm2*4)

VFD2800C43E

300MCM*4 (152mm2*4)

VFD3150C43E

4/0 AWG*4 (107mm2*4)

VFD3550C43E

300MCM*4 (152mm2*4)

VFD4500C43E
300MCM*4 (152mm2*4)
1. VFD4500C43A, VFD4500C43E-1, VFD4500C43E need to use
90℃ wire.
2. UL installations must use 600V, 75℃ or 90℃ wire. Use copper
wire only.
3. Figure 1 shows the specification for using the ring lug.
4.

5.

Specification of grounding wire : 300MCM*4 [152 mm2*4],
Torque: M8 200kg-cm (173 lb-in.) (19.62Nm) (±10%), as
shown in figure 1.
Figure 2 shows the specification of heat shrink tubing that
comply with UL (600C, YDPU2).

Figure 1

Figure 2

5-13

Chapter 6 Control TerminalsC2000 Series

Chapter 6 Control Terminals
Please remove the top cover before wiring the multi-function input and output terminals,
The drive appearances shown in the figures are for reference only, a real drive may look different.
Remove the cover for wiring. Frame A~H
Frame C
Frame A&B
Loosen the screws and press the tabs on both sides Screw torque: 12~15Kg-cm [10.4~13lb-in.]
Loosen the screws and press the tabs on both sides
to remove the cover.
to remove the cover.
Screw torque: 12~15Kg-cm [10.4~13lb-in.]

Frame D0&D
Screw torque: 12~15Kg-cm [10.4~13lb-in.] To remove the cover, lift it slightly and pull outward.
Loosen the screws and press the tabs on both sides to remove the cover.

Frame E
Screw torque: 12~15Kg-cm [10.4~13lb-in.] To remove the cover, lift it slightly and pull outward.

6-1

Chapter 6 Control TerminalsC2000 Series

Frame F
Screw torque: 12~15Kg-cm [10.4~13lb-in.] To remove the cover, lift it slightly and pull outward

Frame G
Screw torque: 12~15Kg-cm [10.4~13lb-in.] To remove the cover, lift it slightly and pull outward

Frame H
Screw torque: 14~16Kg-cm [12.15~13.89lb-in.] To remove the cover, lift it slightly and pull outward

6-2

Chapter 6 Control TerminalsC2000 Series

6-1 Specifications of Control Terminal

Wire Gauge: 26~16AWG（0.1281-1.318mm2）,
Torque: (A) 5kg-cm [4.31Ib-in.] (0.49Nm) (As shown in figure above)
(B) 8kg-cm [6.94Ib-in.] (0.78Nm) (As shown in figure above)
Wiring precautions:
Reserves 5mm and properly install the wire into the terminal; fasten the installation by a
slotted screwdriver. If the wire is stripped, sort the wire before install into the terminal.
 Flathead screwdriver: blade width 3.5mm, tip thickness 0.6mm
 In the figure above, the factory setting for S1-SCM is short circuit. The factory setting for
+24V-COM is short circuit and SINK mode (NPN); please refer to Chapter 4 Wiring for more
detail.
Terminals
Terminal Function
Factory Setting (NPN mode)


+24V
COM
FWD
REV

MI1
~
MI8

Digital control signal common

+24V5% 200mA

(Source)
Digital control signal common (Sink) Common for multi-function input terminals
FWD-DCM:
Forward-Stop command
ON forward running
OFF deceleration to stop
REV-DCM:
Reverse-Stop command
ON reverse running
OFF deceleration to stop
Refer to parameters 02-01~02-08 to program the
multi-function inputs MI1~MI8.
Source mode
ON: the activation current is 3.3mA≧11Vdc
OFF: cut-off voltage≦5Vdc

Multi-function input 1~8

Sink Mode
ON: the activation current is 3.3mA ≦13Vdc
OFF: cut-off voltage≧19Vdc
Digital frequency meter

DFM

DFM

DCM
DCM

MO1

Digital frequency signal common
Multi-function Output 1
(photocoupler)

Regard the pulse voltage as the output monitor signal
Duty-cycle: 50%
Min. load impedance: 1kΩ/100pf
Max. current: 30mA
Max. voltage: 30Vdc
The AC motor drive releases various monitor signals, such as
drive in operation, frequency attained and overload indication,
via transistor (open collector).

6-3

Chapter 6 Control TerminalsC2000 Series

Terminals

Terminal Function

Factory Setting (NPN mode)
MO1

MO2

Multi-function Output 2
MO2

(photocoupler)

MCM

MCM

Multi-function Output Common

Max 48Vdc 50mA

RC1

Multi-function relay output 1 (N.O.) Resistive Load:
a
3A(N.O.)/3A(N.C.) 250VAC
Multi-function relay output 1 (N.C.) 5A(N.O.)/3A(N.C.) 30VDC
b
Inductive Load (COS 0.4):
1.2A(N.O.)/1.2A(N.C.) 250VAC
Multi-function relay common

RA2

Multi-function relay output 2 (N.O.) a

RB2

It is used to output each monitor signal, such as drive is in
Multi-function relay output 2 (N.C.) b operation, frequency attained or overload indication.

RC2

Multi-function relay common

+10V

Potentiometer power supply

Analog frequency setting: +10Vdc 20mA

-10V

Potentiometer power supply

Analog frequency setting: -10Vdc 20mA

RA1
RB1

2.0A(N.O.)/1.2A(N.C.) 30VDC

Analog voltage input
+10V AVI circuit

AVI

Impedance: 20kΩ
Range: 0~20mA/4~20mA/0~10V =0~Max. Output Frequency

AVI

(Pr.01-00)
AVI switch, factory setting is 0~10V

ACM
internal circuit

Analog current input
ACI

ACI circuit

Impedance: 250Ω
Range: 0~20mA/4~20mA/0~10V = 0 ~ Max. Output

ACI

Frequency (Pr.01-00)
ACI Switch, factory setting is 4~20mA
ACM

internal circuit

Auxiliary analog voltage input
+10V

AUI

AUI ( -10V~+ 10V)

Range: -10~+10VDC=0 ~ Max. Output Frequency(Pr.01-00)

A CM
-1 0V

Impedance: 20kΩ

inter nal c irc ui t

6-4

Chapter 6 Control TerminalsC2000 Series

Terminals

Terminal Function

Factory Setting (NPN mode)
0~10V Max. output current 2mA, Max. load 5kΩ
-10~10V maximum output current 2mA, maximum load 5kΩ
Output current: 2mA max
Resolution: 0~10V corresponds to Max. operation frequency
Range: 0~10V  -10~+10V
AFM 1 Switch, factory setting is 0~10V

AFM1

0~10V Max. output current 2mA, Max. load 5kΩ
0~20mA Max. load 500Ω
Output current: 20mA max
Resolution: 0~10V corresponds to Max. operation frequency
Range: 0~10V  4~20mA
AFM 2 Switch, factory setting is 0~10V

AFM2

ACM
STO1
SCM1
STO2
SCM2

Analog Signal Common

Common for analog terminals

Default setting is shorted
Power removal safety function for EN954-1 and IEC/EN61508

When STO1~SCM1;STO2~SCM2 is activated, the activation current is 3.3mA≧11Vdc

SG+
SG-

Modbus RS-485

SGND
RJ-45

PIN 1,2,7,8 : Reserved
PIN 4: SG-

PIN 3, 6: SGND
PIN 5: SG+

NOTE: Wire size of analog control signals: 18 AWG (0.75 mm2) with shielded wire

6-2 Analog input terminals (AVI, ACI, AUI, ACM)


Analog input signals are easily affected by external noise. Use shielded wiring and keep it as
short as possible (<20m) with proper grounding. If the noise is inductive, connecting the shield to
terminal ACM can bring improvement.



If the analog input signals are affected by noise from the AC motor drive, please connect a
capacitor and ferrite core as indicated in the following diagram.

AVI/ACI/AUI
C
AC M

ferrite core

Wind each wires 3 times or more around the core
Digital inputs (FWD, REV, MI1~MI8, COM)


When using contacts or switches to control the digital inputs, please use high quality components
to avoid contact bounce.



The “COM” terminal is the common side of the photo-coupler. Any of wiring method, the “common
point” of all photo-coupler must be the “COM”.
6-5

Chapter 6 Control TerminalsC2000 Series



When the photo-coupler is using internal power supply, the switch connection for Sink and Source
as below:
MI-DCM: Sink mode
MI-+24V: Source mode



When the photo-coupler is using external power supply, please remove the short circuit cable
between the +24V and COM terminals. The connection mode is Sink mode or Source mode is
according to the below:
The “+” of 24V connecting to “COM: Sink mode
The “-“ of 24V connecting to COM: Source mode

Transistor outputs (MO1, MO2, MCM)
 Make sure to connect the digital outputs to the right polarity.


When connecting a relay to the digital outputs connect a surge absorber across the coil and
check the polarity.

6-6

Chapter 6 Control TerminalsC2000 Series

6-3 Remove the Terminal Block
1. Loosen the screws by screwdriver. (As shown in figure below).

2. Remove the control board by pulling it out for a distance 6~8 cm (as 1 in the figure) then lift the control
board upward(as 2 in the figure).

6-7

Chapter 7 Optional AccessoriesC2000 Series

Chapter 7 Optional Accessories
7-1 All Brake Resistors and Brake Units Used in AC Motor Drives
7-2 Non-fuse Circuit Breaker
7-3 Fuse Specification Chart
7-4 AC/DC Reactor
7-5 Zero Phase Reactor
7-6 EMI Filter
7-7 Digital Keypad
7-8 Panel Mounting
7-9 Conduit Box Kit
7-10 Fan Kit
7-11 Flange Mounting Kit
7-12 USB/RS-485 Communication Interface IF6530

7-1

Chapter 7 Optional Accessories C2000 Series

The optional accessories listed in this chapter are available upon request. Installing additional
accessories to your drive would substantially improve the drive’s performance. Please select an applicable
accessory according to your need or contact the local distributor for suggestion.

7-1 All Brake Resistors and Brake Units Used in AC Motor Drives
230V
Applicable
Motor
HP

kW

1
2
3
5
7.5
10
15
20
25
30
40
50
60
75
100
125

0.7
1.5
2.2
3.7
5.5
7.5
11
15
18
22
30
37
45
55
75
90

*1 125%Braking Torque 10%ED
Braking
Torque
(kg-m)
0.5
1.0
1.5
2.5
3.7
5.1
7.5
10.2
12.2
14.9
20.3
25.1
30.5
37.2
50.8
60.9

Brake
Unit
*4VFDB
2015*2
2022*2
2022*2
2022*3
2022*4
2022*4

*3Braking Resistor series for
each Brake Unit
BR080W200*1
BR200W091*1
BR300W070*1
BR400W040*1
BR1K0W020*1
BR1K0W020*1
BR1K5W013*1
BR1K0W4P3*2 2 series
BR1K0W4P3*2 2 series
BR1K5W3P3*2 2 series
BR1K0W5P1*2 2 series
BR1K2W3P9*2 2 series
BR1K5W3P3*2 2 series
BR1K2W3P9*2 2 series
BR1K2W3P9*2 2 series
BR1K5W3P3*2 2 series

Resistor value
spec. for each
AC motor Drive
80W200Ω
200W91Ω
300W70Ω
400W40Ω
1000W20Ω
1000W20Ω
1500W13Ω
2000W8.6Ω
2000W8.6Ω
3000W6.6Ω
4000W5.1Ω
4800W3.9Ω
6000W3.3Ω
7200W2.6Ω
9600W2Ω
12000W1.65Ω

*2 Max. Brake Torque
Total
Min.
Braking
Resistor
Current (A) Value (Ω)
1.9
63.3
4.2
47.5
5.4
38.0
9.5
19.0
19
14.6
19
14.6
29
13.6
44
8.3
44
8.3
58
5.8
75
4.8
97
3.2
118
3.2
145
2.1
190
1.6
230
1.6

Max. Total
Braking
Current (A)
6
8
10
20
26
26
28
46
46
66
80
120
120
180
240
240

Peak
Power
(kW)
2.3
3.0
3.8
7.6
9.9
9.9
10.6
17.5
17.5
25.1
30.4
45.6
45.6
68.4
91.2
91.2

460V
Applicable
Motor

*1 125%Braking Torque 10%ED
Braking
Torque
(kg-m)

Brake
Unit

*3Braking Resistor series for
each Brake Unit

*2 Max. Brake Torque

Resistor value
Total
Min.
Max. Total
spec. for each
Braking
Resistor
Braking
AC motor Drive Current (A) Value (Ω) Current (A)

Peak
Power
(kW)

HP

kW

1
2
3
5
5.5
7.5
10
15
20
25
30

0.7
1.5
2.2
3.7
4.0
5.5
7.5
11
15
18
22

0.5
1.0
1.5
2.5
2.7
3.7
5.1
7.5
10.2
12.2
14.9

-

BR080W750*1
BR200W360*1
BR300W250*1
BR400W150*1

80W750Ω
200W360Ω
300W250Ω
400W150Ω

1
2.1
3
5.1

190.0
126.7
108.6
84.4

4
6
7
9

3.0
4.6
5.3
6.8

-

BR1K0W075*1

1000W75Ω

10.2

54.3

14

10.6

-

1000W75Ω
1500W43Ω
2000W32Ω
2000W32Ω
3000W26Ω

10.2
17.6
24
24
29

47.5
42.2
26.2
23.0
23.0

16
18
29
33
33

12.2
13.7
22.0
25.1
25.1

40

30

20.3

-

4000W16Ω

47.5

14.1

54

41.0

50

37

25.1

4045*1

4800W15Ω

50

12.7

60

45.6

60

45

30.5

4045*1

6000W13Ω

59

12.7

60

45.6

75

55

76

9.5

80

60.8

75

4030*2
4045*2

8000W10.2Ω

100

37.2
50.8

9600W7.5Ω

100

6.3

120

91.2

125

90

60.9

4045*2

12000W6.5Ω

117

6.3

120

91.2

150

110

74.5

4110*1

BR1K0W075*1
BR1K5W043*1
BR1K0W016*2
2 series
BR1K0W016*2
2 series
BR1K5W013*2
2 series
2 parallel,
BR1K0W016*4
2 series
2 parallel,
BR1K2W015*4
2 series
2 parallel,
BR1K5W013*4
2 series
BR1K0W5P1*4
4 parallel
2 parallel,
BR1K2W015*4
2 series
2 parallel,
BR1K5W013*4
2 series
5 parallel,
BR1K2W015*10
2 series

12000W6Ω

126

6.0

126

95.8

*4VFDB

7-2

Chapter 7 Optional AccessoriesC2000 Series

460V
Applicable
Motor
HP

kW

*1 125%Braking Torque 10%ED
Braking
Torque
(kg-m)

*3Braking Resistor series for
each Brake Unit

Brake
Unit

*2 Max. Brake Torque

Resistor value
Total
Min.
Max. Total
spec. for each
Braking
Resistor
Braking
AC motor Drive Current (A) Value (Ω) Current (A)

Peak
Power
(kW)

6 parallel,
18000W4Ω
190
4.0
190
144.4
2 series
6 parallel,
215 160
108.3 4160*1 BR1K5W012*12
18000W4Ω
190
4.0
190
144.4
2 series
7 parallel,
21000W3.4Ω
225
3.4
225
172.1
250 185
125.3 4185*1 BR1K5W012*14
2 series
5 parallel,
300 220
148.9 4110*2 BR1K2W015*10
24000W3Ω
252
3.0
252
190.5
2 series
6 parallel,
375 280
189.6 4160*2 BR1K5W012*12
36000W2Ω
380
2.0
380
288.8
2 series
6 parallel,
425 315
213.3 4160*2 BR1K5W012*12
36000W2Ω
380
2.0
380
288.8
2 series
7 parallel,
475 355
240.3 4185*2 BR1K5W012*14
42000W1.7Ω
450
1.7
450
344.2
2 series
1
* Calculation for 125% brake toque: (kw)*125%*0.8; where 0.8 is motor efficiency.
Because there is a resistor limit of power consumption, the longest operation time for 10%ED is 10sec (on: 10sec/ off: 90sec).
*2 Please refer to the Brake Performance Curve for “Operation Duration & ED” vs. “Braking Current”.
*3 For heat dissipation, a resistor of 400W or lower should be fixed to the frame and maintain the surface temperature below
50℃; a resistor of 1000W and above should maintain the surface temperature below 350℃.
*4 Please refer to VFDB series Braking Module Instruction for more detail on braking resistor.
175

132

89.4

4160*1

BR1K5W012*12

NOTE
1.

Definition for Brake Usage ED%
Explanation: The definition of the brake usage ED (%) is for assurance of enough time for the brake unit and brake resistor to
dissipate away heat generated by braking. When the brake resistor heats up, the resistance would increase with
temperature, and brake torque would decrease accordingly. Recommended cycle time is one minute.

For safety concern, install an overload relay (O.L) between the brake unit and the brake resistor in conjunction with the
magnetic contactor (MC) prior to the drive for abnormal protection. The purpose of installing the thermal overload relay is to
protect the brake resistor from damage due to frequent brake, or due to brake unit keeping operating resulted from unusual
high input voltage. Under such circumstance, just turn off the power to prevent damaging the brake resistor.
NFB

MC

R/L1
S/L2
T/L3
O.L.

V FD

MOTOR

R/L1 U/T1
S/L2
V/T2
T/L3
W/T3

MC

+(P)

SA

- (N)

Varistor

IM

+ (P) (N )

B1

O.L.

Brake unit
VFDB
XXXX
B2
MASTER
Thermal relay
or Temperature Switch
Trip Contact

T hermal relay

M1 M2

+ Brake (P) (N)

Resistor

B1

Brake unit
VFDB
XXXX
B2

MASTER
Temperature
M1 M2
switch

T hermal relay
O.L.

Brake
Resistor

22Parallel /Serie
Temperature switch

When AC Drive is equipped with a DC reactor, please read user manual to know th
wiring method of input
。 circuit of brake unit +(P).
Do Not connect input circuit -(N) to the neutral point of the power system.
2.

If damage to the drive or other equipment is due to the fact that the brake resistors and brake modules in use are not
provided by Delta, the warranty will be void.
7-3

Chapter 7 Optional Accessories C2000 Series
3.

Take into consideration the safety of the environment when installing the brake resistors. If the minimum resistance value is
to be utilized, consult local dealers for the calculation of Watt figures.

4.

When using more than 2 brake units, equivalent resistor value of parallel brake unit can’t be less than the value in the
column “Minimum Equivalent Resistor Value for Each AC Drive” (the right-most column in the table). Please read the wiring
information in the user manual of brake unit thoroughly prior to operation

5.

This chart is for normal usage; if the AC motor drive is applied for frequent braking, it is suggested to enlarge 2~3 times of
the Watts.
Thermal Relay:
Thermal relay selection is basing on its overload capability. A standard braking capacity for C2000 is 10%ED (Tripping
time=10s). The figure below is an example of 406V, 110kw AC motor drive. It requires the thermal relay to take 260%
overload capacity in 10s (Host starting) and the braking current is 126A. In this case, user should select a rated 50A thermal
relay. The property of each thermal relay may vary among different manufacturer, please carefully read specification.
60
40
30
20

Tripping time
Second

6.

10
8
6
4
3
2
1
0.8
0.6
0.4
0.3
0.8

1

1.5

2

3

4

5

6 7 8 9 10

Multiple of current setting

7-4

xln (A)

15

Chapter 7 Optional AccessoriesC2000 Series

7-2 Non-fuse Circuit Breaker
Comply with UL standard: Per UL 508, paragraph 45.8.4, part a.
The rated current of the breaker shall be 2~4 times of the maximum rated input current of AC motor
drive.
3-phase 230V
Model
VFD007C23A
VFD015C23A
VFD022C23A
VFD037C23A
VFD055C23A
VFD075C23A
VFD110C23A
VFD150C23A
VFD185C23A
VFD220C23A
VFD300C23A/E
VFD370C23A/E
VFD450C23A/E
VFD550C23A/E
VFD750C23A/E
VFD900C23A/E

Recommended
non-fuse breaker (A)
15
20
30
40
50
60
100
125
150
200
225
250
300
400
450
600

3-phase 460V
Model
VFD007C43A/E
VFD015C43A/E
VFD022C43A/E
VFD040C43A/E
VFD037C43A/E
VFD055C43A/E
VFD075C43A/E
VFD110C43A/E
VFD150C43A/E
VFD185C43A/E
VFD220C43A/E
VFD300C43A/E
VFD370C43A/E/S/U
VFD450C43A/E/S/U
VFD550C43A/E
VFD750C43A/E
VFD900C43A/E
VFD1100C43A/E
VFD1320C43A/E
VFD1600C43A/E
VFD1850C43A/E
VFD2200C43A/E
VFD2800C43A/E
VFD3150C43A/E
VFD3550C43A/E

7-5

Recommended
non-fuse breaker(A)
5
10
15
20
20
30
40
50
60
75
100
125
150
175
250
300
300
400
500
600
600
800
1000
1200
1350

Chapter 7 Optional Accessories C2000 Series

7-3 Fuse Specification Chart
 Use only the fuses comply with UL certificated.
 Use only the fuses comply with local regulations.
230V Model
VFD007C23A
VFD015C23A
VFD022C23A
VFD037C23A
VFD055C23A
VFD075C23A
VFD110C23A
VFD150C23A
VFD185C23A
VFD220C23A
VFD300C23A/E
VFD370C23A/E
VFD450C23A/E
VFD550C23A/E
VFD750C23A/E
VFD900C23A/E

460VModel

Input Current I(A)
Heavy Duty
Normal Duty
6.1
11
15
18.5
26
34
50
68
78
95
118
136
162
196
233
315

6.4
12
16
20
28
36
52
72
83
99
124
143
171
206
245
331

Input Current I(A)
Heavy Duty
Normal Duty

Line Fuse
I (A)

Bussmann P/N

20
35
50
80
100
130
175
250
300
350
400
500
700
800
1000
1000

JJS-20
JJS-35
JJS-50
JJS-80
JJS-100
JJS-130
JJS-175
JJS-250
JJS-300
JJS-350
DLS-R-400
DLS-R-500
JJN-700
JJN-800
JJN-1000
KTU-1000

Line Fuse
I (A)

Bussmann P/N

VFD007C43A/E
4.1
4.3
10
JJS-10
VFD015C43A/E
5.6
5.9
15
JJS-15
VFD022C43A/E
8.3
8.7
20
JJS-20
VFD037C43A/E
13
14
30
JJS-30
VFD040C43A/E
14.5
15.5
35
JJS-35
VFD055C43A/E
16
17
45
JJS-45
VFD075C43A/E
19
20
70
JJS-70
VFD110C43A/E
25
26
90
JJS-90
VFD150C43A/E
33
35
125
JJS-125
VFD185C43A/E
38
40
125
JJS-125
VFD220C43A/E
45
47
150
JJS-150
VFD300C43A/E
60
63
200
JJS-200
VFD370C43/S/U
70
74
300
DLS-R-300
VFD450C43/S/U
96
101
350
DLS-R-350
VFD550C43A/E
108
114
400
DLS-R-400
VFD750C43A/E
149
157
600
DLS-R-600
VFD900C43A/E
159
167
600
JJN-600
VFD1100C43A/E
197
207
800
JJS-800
VFD1320C43A/E
228
240
800
KTU-800
VFD1600C43A/E
285
300
800
KTU-800
VFD1850C43A/E
361
380
800
KTU-800
VFD2200C43A/E
380
400
1000
KTU-1000
VFD2800C43A/E
469
494
1200
KTU-1200
VFD3150C43A/E
527
555
1200
KTU-1200
VFD3550C43A/E
594
625
1600
KTU-1600
＊ Contact Delta Electronics or an authorized distributor for corresponding fuse of VFD4500C43A/E

7-6

Chapter 7 Optional AccessoriesC2000 Series

7-4 AC/DC Reactor
When the AC Motor Drive is connected directly to a large-capacity power transformer
(600kVA or above) or when a phase lead capacitor is switched, excess peak currents may
occur in the power input circuit due to the load changes and the converter section may be
damaged. To avoid this, it is recommend to use a serial connected AC input reactor (3%) at
the AC Motor Drive mains input side to reduce the current and improve the input power
efficiency.

AC Input/output Reactor
200V~230V/ 50~60Hz
Type KW

Rated Amps
3%
Max. continuous
HP of AC Reactor
impedance
Amps (Arms)
(Arms)
(mH)

5%
3%
Built-in
impedance
Input AC reactor
DC reactor
(mH)
Delta part #

007 0.75

1

5

8.64

2.536

4.227

X

N/A

015

1.5

2

8

12.78

1.585

2.642

X

N/A

022

2.2

3

11

18

1.152

1.922

X

N/A

037

3.7

5

17

28.8

0.746

1.243

X

N/A

055

5.5

7.5

25

43.2

0.507

0.845

X

N/A

075

7.5

10

33

55.8

0.32

0.534

X

DR033AP320

110

11

15

49

84.6

0.216

0.359

X

DR049AP215

150

15

20

65

111.6

0.163

0.271

X

DR065AP162

185 18.5

25

75

127.8

0.169

0.282

X

N/A

220

22

30

90

154.8

0.141

0.235

X

N/A

300

30

40

120

205.2

0.106

0.176

O

N/A

370

37

50

146

250.2

0.087

0.145

O

N/A

450

45

60

180

307.8

0.070

0.117

O

N/A

550

55

75

215

367.2

0.059

0.098

O

N/A

750

75

100

255

435.6

0.049

0.083

O

N/A

900

90

125

346

592.2

0.037

0.061

O

N/A

380V~460V/ 50~60Hz
Type KW

Rated Amps
3%
Max. continuous
HP of AC Reactor
impedance
Amps (Arms)
(Arms)
(mH)

5%
3%
Built-in
impedance
Input AC reactor
DC reactor
(mH)
Delta part #

007 0.75

1

3

5.22

8.102

13.502

X

N/A

015

1.5

2

4

6.84

6.077

10.127

X

N/A

022

2.2

3

6

10.26

4.050

6.752

X

N/A

037

3.7

5

9

14.58

2.700

4.501

X

N/A

040

4

5

10.5

17.1

2.315

3.858

X

N/A

055

5.5

7.5

12

19.8

2.025

3.375

X

N/A

075

7.5

10

18

30.6

1.174

1.957

X

DR018A0117

110

11

15

24

41.4

0.881

1.468

X

DR024AP880

150

15

20

32

54

0.66

1.101

X

DR032AP660

7-7

Chapter 7 Optional Accessories C2000 Series
Type KW

Rated Amps
3%
Max. continuous
HP of AC Reactor
impedance
Amps (Arms)
(Arms)
(mH)

5%
3%
Built-in
impedance
Input AC reactor
DC reactor
(mH)
Delta part #

185 18.5

25

38

64.8

0.639

1.066

X

N/A

220

22

30

45

77.4

0.541

0.900

X

N/A

300

30

40

60

102.6

0.405

0.675

O

N/A

370

37

50

73

124.2

0.334

0.555

O

N/A

450

45

60

91

154.8

0.267

0.445

O

N/A

550

55

75

110

189

0.221

0.368

O

N/A

750

75

100

150

257.4

0.162

0.270

O

N/A

900

90

125

180

307.8

0.135

0.225

O

N/A

1100 110

150

220

376.2

0.110

0.184

O

N/A

1320 132

175

260

444.6

0.098

0.162

O

N/A

1600 160

215

310

531

0.078

0.131

O

N/A

1850 185

250

370

633.6

0.066

0.109

O

N/A

2200 220

300

460

786.6

0.054

0.090

O

N/A

2800 280

375

550

941.4

0.044

0.074

O

N/A

3150 315

420

616

1053

0.039

0.066

O

N/A

3550 355

475

683

1168.2

0.036

0.060

O

N/A

4500 450

600

866

1468.8

0.028

0.047

O

N/A

DC Reactor
200V~230V/ 50~60Hz
Type

kW

HP

Rated Amps of AC Reactor

Max. continuous Amps

Inductance（mh）

007

0.75

1

5

8.64

5.857

015

1.5

2

8

12.78

3.660

022

2.2

3

11

18

2.662

037

3.7

5

17

28.8

1.722

055

5.5

7.5

25

43.2

1.172

075

7.5

10

33

55.8

0.851

110

11

15

49

84.6

0.574

150

15

20

65

111.6

0.432

185

18.5

25

75

127.8

0.391

220

22

30

90

154.8

0.325

380V~460V/ 50~60Hz
Type

kW

HP

Rated Amps of AC Reactor

Max. continuous Amps

Inductance（mh）

007

0.75

1

3

5.22

18.709

015

1.5

2

4

6.84

14.031

022

2.2

3

6

10.26

9.355

037

3.7

5

9

14.58

6.236

040

4

5

10.5

17.1

5.345

7-8

Chapter 7 Optional AccessoriesC2000 Series
Type

kW

HP

Rated Amps of AC Reactor

Max. continuous Amps

Inductance（mh）

055

5.5

7.5

12

19.8

4.677

075

7.5

10

18

30.6

3.119

110

11

15

24

41.4

2.338

150

15

20

32

54

1.754

185

18.5

25

38

64.8

1.477

220

22

30

45

77.4

1.247

THD
Motor Drive

Without Built-in DC Reactor

Spec

With Built in DC Reactor

3% Input

5% Input

4%

3% Input

5% Input

AC Reactor

AC Reactor

DC Reactor

AC Reactor

AC Reactor

5th

38.5%

30.8%

25.5%

27.01%

25.5%

7th

15.3%

9.4%

18.6%

9.54%

8.75%

11th

7.1%

6.13%

7.14%

4.5%

4.2%

13th

3.75%

3.15%

0.48%

0.22%

0.17%

THDi

43.6%

34.33%

38.2%

30.5%

28.4%

Reactor Spec.

Note:

THDi may have some difference due to different installation conditions and environment

According to IEC61000-3-12, DC Reactor is designed with 4% system impedance, and AC Reactor is designed
with 3% system impedance.

7-9

Chapter 7 Optional Accessories C2000 Series

C

B

G

7-5 Zero Phase Reactors

D
A

F

E

UNIT: mm(inch)
model
RF008X00A
RF004X00A

A

B

C

D

E

F

98
(3.858)
110
(4.331)

73
(2.874)
87.5
(3.445)

36.5
(1.437)
43.5
(1.713)

29
(1.142)
36
(1.417)

56.5
(2.224)
53
(2.087)

86
(3.386)
96
(3.780)

G(Ø)
5.5
(0.217)
5.5
(0.217)

Torque
< 10kgf/cm2
< 10kgf/cm2

C

H

B

G

F
D

E
UNIT: mm(inch)

model
RF002X00A

A
200
(7.874)

B
172.5
(6.791)

C
90
(3.543)

D
78
(3.071)

E
55.5
(2.185)

F
184
(7.244)

G(Ø)
5.5
(0.217)

H
22
(0.866)

Torque
<45kgf/cm2

UNIT: mm(inch)
model

A

B

C

D

E

F

G(Ø)

H

I

RF300X00A 241(9.488) 217(8.543) 114(4.488) 155(6.102) 42(1.654) 220(8.661) 6.5(0.256) 7.0(0.276) 20(0.787)

7-10

Chapter 7 Optional AccessoriesC2000 Series
Reactor
model (Note)

Recommended Wire Size

Wiring
Method

Qty

Corresponding motor drives
VFD007C23A; VFD015C23A; VFD022C23A;

RF008X00A

≦8 AWG

≦8.37 mm2

Diagram A

1

VFD037C23A; VFD007C43A; VFD015C43A;
VFD022C43A; VFD037C43A; VFD040C43A
VFD055C43A
VFD055C23A; VFD075C23A; VFD110C23A;

RF004X00A

≦4 AWG

2

≦21.15 mm

Diagram A

1

VFD110C43A; VFD150C43A; VFD075C43A;
VFD110C43A; VFD150C43A
VFD150C23A; VFD185C23A; VFD220C23A;

RF002X00A

≦2 AWG

≦33.62 mm2

Diagram A

1

VFD300C23A; VFD370C23A; VFD185C43A;
VFD220C43A; VFD300C43A; VFD370C43A;
VFD450C43A; VFD550C43A; VFD750C43A
VFD450C23A; VFD550C23A; VFD750C23A;
VFD900C23A; VFD900C43A; VFD1100C43A;

RF300X00A

≦300 MCM

≦152 mm

2

Diagram A

1

VFD1320C43A; VFD1600C43A; VFD1850C43A;
VFD2200C43A; VFD2800C43A; VFD3150C43A;
VFD3550C43A; VFD4500C43A

Note: 600V insulated cable wire

Diagram A
Please put all wires through at least one core without winding.
Zero Phase Reactor

R/L1

U/T1

S/L2

V/T1

T/L3

W/T1

MOTOR

Note 1: The table above gives approximate wire size for the zero phase reactors but the selection is ultimately
governed by the type and diameter of cable fitted i.e. the cable must fit through the center hole of zero phase
reactors.
Note 2: Only the phase conductors should pass through, not the earth core or screen.
Note3: When long motor output cables are used an output zero phase reactor may be required to reduce radiated
emissions from the cable.

7-11

Chapter 7 Optional Accessories C2000 Series

7-6 EMI Filter
CE Cable Length
Model

input
Current

Applicable EMI
Filter

Zero Phase
Reactor

default carrier frequency

Radiation
Emission
default carrier
frequency

EN61800-3
C1

EN61800-3
C2

EN61800-3
C2

50m

100m

Pass

50m

100m

Pass

50m

100m

Pass

VFD007C23A

6.4A

VFD015C23A

12A

VFD022C23A

16A

VFD037C23A

20A

50m

100m

Pass

VFD055C23A

28A

50m

100m

Pass

VFD075C23A

36A

50m

100m

Pass

VFD110C23A

52A

50m

100m

Pass

VFD150C23A

76A

50m

100m

Pass

VFD185C23A

83A

50m

100m

Pass

VFD220C23A

99A

50m

100m

Pass

VFD300C23A

124A

50m

100m

Pass

VFD370C23A

143A

50m

100m

Pass

VFD450C23A

171A

50m

100m

Pass

VFD550C23A

206A

50m

100m

Pass

VFD750C23A

245A

50m

100m

Pass

VFD900C23A

331A

50m

100m

Pass

VFD007C43A

4.3A

50m

100m

Pass

VFD015C43A

5.9A

50m

100m

Pass

VFD022C43A

8.7A

50m

100m

Pass

VFD037C43A

14A

50m

100m

Pass

VFD040C43A

15.5A

50m

100m

Pass

VFD055C43A

17A

50m

100m

Pass

VFD075C43A

20A

50m

100m

Pass

VFD110C43A

26A

50m

100m

Pass

VFD150C43A

35A

50m

100m

Pass

VFD185C43A

40A

50m

100m

Pass

VFD220C43A

47A

50m

100m

Pass

VFD300C43A

63A

50m

100m

Pass

VFD370C43A

74A

50m

100m

Pass

VFD450C43A

101A

50m

100m

Pass

VFD550C43A

114A

50m

100m

Pass

VFD750C43A

157A

50m

100m

Pass

EMF021A23A

EMF056A23A

RF008X00A

RF004X00A

KMF3100A
RF002X00A
B84143D0150R127

B84143B0250S020

RF300X00A

B84143B0400S020
EMF014A43A
RF008X00A
EMF018A43A

EMF039A43A

RF004X00A

KMF370A
RF002X00A
B84143D0150R127

7-12

Chapter 7 Optional AccessoriesC2000 Series
CE Cable Length
Model

input
Current

VFD900C43A

167A

VFD1100C43A

207A

VFD1320C43A

240A

VFD1600C43A

300A

VFD1850C43A

380A

VFD2200C43A

400A

VFD2800C43A

494A

VFD3150C43A

555A

VFD3550C43A

625A

VFD4500C43A

866A

Applicable EMI
Filter

Zero Phase
Reactor

B84143D0200R127

MIF3400B
RF300X00A

MIF3800
B84143B1000S020

default carrier frequency

Radiation
Emission
default carrier
frequency

EN61800-3
C1

EN61800-3
C2

EN61800-3
C2

50m

100m

Pass

50m

100m

Pass

50m

100m

Pass

50m

100m

Pass

50m

100m

Pass

50m

100m

Pass

50m

100m

Pass

50m

100m

Pass

50m

100m

Pass

50m

100m

Pass

EMI Filter Installation
All electrical equipment, including AC motor drives, will generate high-frequency/low-frequency noise and will
interfere with peripheral equipment by radiation or conduction when in operation. By using an EMI filter with correct
installation, much interference can be eliminated. It is recommended to use DELTA EMI filter to have the best
interference elimination performance.
We assure that it can comply with following rules when AC motor drive and EMI filter are installed and wired
according to user manual:

EN61000-6-4

EN61800-3: 1996

EN55011 (1991) Class A Group 1 (1st Environment, restricted distribution)

General precaution
1.
2.
3.
4.
5.

EMI filter and AC motor drive should be installed on the same metal plate.
Please install AC motor drive on footprint EMI filter or install EMI filter as close as possible to the AC motor drive.
Please wire as short as possible.
Metal plate should be grounded.
The cover of EMI filter and AC motor drive or grounding should be fixed on the metal plate and the contact area
should be as large as possible.

Choose suitable motor cable and precautions
Improper installation and choice of motor cable will affect the performance of EMI filter. Be sure to observe the
following precautions when selecting motor cable.
1. Use the cable with shielding (double shielding is the best).
2. The shielding on both ends of the motor cable should be grounded with the minimum length and maximum
contact area.
3. Remove any paint on metal saddle for good ground contact with the plate and shielding.

7-13

Chapter 7 Optional Accessories C2000 Series
Remove any paint on metal saddle for good ground contact with
the plate and shielding.

saddle

the plate with grounding

Figure 1

Saddle on both ends

Saddle on one end
Figure 2

The length of motor cable
When motor is driven by an AC motor drive of PWM type, the motor terminals will experience surge voltages
easily due to components conversion of AC motor drive and cable capacitance. When the motor cable is very long
(especially for the 460V series), surge voltages may reduce insulation quality. To prevent this situation, please follow
the rules below:
 Use a motor with enhanced insulation.
 Connect an output reactor (optional) to the output terminals of the AC motor drive
 The length of the cable between AC motor drive and motor should be as short as possible (10 to 20 m or less)
 For models 7.5hp and above:
Insulation level of motor

1000V

1300V

1600V

460VAC input voltage

66 ft (20m)

328 ft (100m)

1312 ft (400m)

230VAC input voltage

1312 ft (400m)

1312 ft (400m)

1312 ft (400m)

 For models 5hp and less:
Insulation level of motor

1000V

1300V

1600V

460VAC input voltage

66 ft (20m)

165 ft (50m)

165 ft (50m)

230VAC input voltage

328 ft (100m)

328 ft (100m)

328 ft (100m)

NOTE

Never connect phase lead capacitors or surge absorbers to the output terminals of the AC motor drive.

7-14

Chapter 7 Optional AccessoriesC2000 Series
 If the length is too long, the stray capacitance between cables will increase and may cause leakage current. It
will activate the protection of over current, increase leakage current or not insure the correction of current
display. The worst case is that AC motor drive may damage.
 If more than one motor is connected to the AC motor drive, the total wiring length is the sum of the wiring length
from AC motor drive to each motor.
 For the 460V series AC motor drive, when an overload relay is installed between the drive and the motor to
protect motor over heating, the connecting cable must be shorter than 50m. However, an overload relay
malfunction may still occur. To prevent the malfunction, install an output reactor (optional) to the drive or lower
the carrier frequency setting (Pr.00-17).
NOTE

When a thermal O/L relay protected by motor is used between AC motor drive and motor, it may malfunction
(especially for 460V series), even if the length of motor cable is only 165 ft (50m) or less. To prevent it, please use AC
reactor and/or lower the carrier frequency (Pr. 00-17 PWM carrier frequency).

7-15

Chapter 7 Optional Accessories C2000 Series

7-7 Digital Keypad
7-7-1 KPC-CE01

A : LED Disp lay
D ispla y freq uen cy, cu rre nt, vo ltag e and erro r etc.

: Status Indi cator
F: Fre que ncy C omma nd
H: Outp ut Frequ ency
U: User De fine d Uni ts
ERR: CAN Erro r Ind icator
RU N: CAN Ru n Indi ca tor

C : Function

(Re fer to the chart foll ow s for deta il de scripti on )

Key

Description

ESC

ESC Key
Press ESC key to return to the previous page. It also functions as a return to last category key in the sub-menu.
Menu Key
Press MENU key under any condition will return to the main MENU.
Menu content:
1. Parameter Detail
3. Keypad locked
2. Copy Parameter
4. PLC Function
ENTER Key
Press ENTER and go to the next level. If it is the last level then press ENTER to execute the command.
HAND ON Key
1. HAND key will operates according to the parameter settings when the source of HAND master frequency
command and the source of HAND operation command is properly set,. The factory setting of the source
command for frequency and operation are from the digital keypad .
2. Press HAND key in stop status, the drive setting switches to the parameter setting of HAND. Press HAND
key in during operation, the drive will come to stop then switches to the parameter setting of HAND.
3. When process complete: H/A LED ON.
Auto Operation Key
1. AUTO function executes according to the parameter settings of the source of AUTO frequency and AUTO
operation. The factory setting is the external terminal (source of operation is 4-20mA).
2. Press the ATUO key in stop status, the drivel switches to auto-setting. Press the auto key during operation
status, the drivel will come to stop and switch to auto-setting.
3. When process complete: H/A LED is OFF
Operation Direction Key
1. FWD/REV key controls the operation direction but will NOT activate the drive. FWD: forward, REV: reverse.
2. The drive operates in the direction as shown by the LED light.
Start Key
1. This button is functional only when the keypad is the source of the command.
2. This button allows the motor drive to run by following its settings. See Description of LED functions for LED
status
3. Press repeatedly the “RUN” button is allow while the motor drive is stopping.
Stop Key.
1. STOP key has the highest priority in command.
2. Press STOP key, the drive will come to stop under any condition.
3. The RESET key can be used to reset the drive when faults occur. If the RESET key is not responding, check
MENU  Fault Records and check the most recent fault.

MENU

ENTER
HAND

AUTO

FWD/REV
RUN

STOP

7-16

Chapter 7 Optional AccessoriesC2000 Series

Descriptions of LED Functions
LED

Descriptions
Steady ON: operation indicator of the AC motor drive, including DC brake, zero speed, standby,
restart after fault and speed search.
Blinking: drive is decelerating to stop or in the status of base block.
Steady OFF: drive doesn’t execute the operation command
Steady ON: stop indicator of the AC motor drive.
Blinking: drive is in the standby status.
Steady OFF: drive doesn’t execute “STOP” command.
Operation Direction LED 『Green light= Forward』；
『Red light= Reversely』
Steady ON: the drive is running forward.
Blinking: the drive is changing direction.
Steady Off: the drive is running reversely.
RUN (Green light):
LED
status
OFF
CANopen at initial

Condition/State
No LED

Blinking CANopen at pre-operation
CANopen ~”RUN”
Single
flash

ON

CANopen at stopped

CANopen at operation status
No LED

ERR (Red light):
LED
status
OFF
Single One message fail
flash

CANopen ~”ERR”

Double
flash

Triple
flash

Condition/ State
No Error

Guarding fail or heartbeat fail

SYNC fail

ON

Bus off

7-17

Chapter 7 Optional Accessories C2000 Series

7-7-2 Dimension

7-7-3 RJ45 Extension Lead for Digital Keypad
Part #

Description

CBC-K3FT

3 feet RJ45 extension lead (approximately 0.9m)

CBC-K5FT

5 feet RJ45 extension lead (approximately 1.5 m)

CBC-K7FT

7 feet RJ45 extension lead (approximately 2.1 m)

CBC-K10FT

10 feet RJ45 extension lead (approximately 3 m)

CBC-K16FT

16 feet RJ45 extension lead (approximately 4.9 m)

7-18

Chapter 7 Optional AccessoriesC2000 Series

7-8 Panel Mounting (MKC-KPPK)
For MKC-KPPK model, user can choose wall mounting or embedded mounting, protection level is IP56.
Applicable to the digital keypads (KPC-CC01 & KPC-CE01).

Wall Mounting

Embedded Mounting

accessories*1

accessories*2

Screw *4 ~M4*p 0.7 *L8mm
Torque: 10-12kg-cm (8.7-10.4lb-in.)
Panel cutout dimension
Unit: mm [inch]

Screw *4 ~M4*p 0.7 *L8mm
Torque: 10-12kg-cm (8.7-10.4lb-in.)

Panel cutout dimension

Unit: mm [inch]

Normal cutout dimension
Panel
1.2mm
1.6mm
2.0mm
thickness
A
66.4 [2.614]
B
110.2 [4.339] 111.3 [4.382] 112.5 [4.429]
*Deviation: ±0.15mm /±0.0059inch

Cutout dimension (Waterproof level: IP56)
Panel
1.2mm
1.6mm
2.0mm
thickness
A
66.4 [2.614]
B

110.8 [4.362]
*Deviation: ±0.15mm /±0.0059inch

7-19

Chapter 7 Optional Accessories C2000 Series

7-20

Chapter 7 Optional AccessoriesC2000 Series

7-9 Conduit Box Kit


Appearance

Frame D0
Applicable models
VFD370C43S/43U; VFD450SC43S/43U;

Frame D
Applicable models

Model number『MKC-D0N1CB』

Model number『MKC-DN1CB』

ITEM
Description
1 Screw M5*0.8*10L
2 Bushing Rubber 28
3 Bushing Rubber 44
4 Bushing Rubber 73
5 Conduit box cover
6 Conduit box base

ITEM
Description
1 Screw M5*0.8*10L
2 Bushing Rubber 28
3 Bushing Rubber 44
4 Bushing Rubber 88
5 Conduit box cover
6 Conduit box base

Qty.
4
2
2
2
1
1

VFD300C23A/23E; VFD370C23A/23E;VFD370C43A/43E;
VFD450C43A/43E; VFD550C43A/43E; VFD750C43A/43E
Qty.
4
2
2
2
1
1

Frame E
Applicable models

Frame F
Applicable models

VFD450C23A/23E; VFD550C23A/23E; VFD750C23A/23E;
VFD900C43A/43E; VFD1100C43A/43E

VFD900C23A/23E; VFD1320C43A/43E; VFD1600C43A/43E

Model number『MKC-EN1CB』

Model number『MKC-FN1CB』

ITEM
Description
Qty.
1 Screw M5*0.8*10L
6
2 Bushing Rubber 28
2
3 Bushing Rubber 44
4
4 Bushing Rubber 100 2
5 Conduit box cover
1
6 Conduit box base
1

ITEM
Description
Qty.
1 Screw M5*0.8*10L
8
2 Bushing Rubber28
2
3 Bushing Rubber 44
4
4 Bushing Rubber 100 2
5 Conduit box cover
1
6 Conduit box base
1

7-21

Chapter 7 Optional Accessories C2000 Series
Frame G
Applicable models
VFD1850C43A/43E; VFD2200C43A/43E

Model number『MKC-GN1CB』
ITEM
Description
Qty.
1 Screw M5*0.8*10L
12
2 Bushing Rubber 28
2
3 Bushing Rubber 44
2
4 Bushing Rubber 130 3
5 Conduit box cover
1
6 Conduit box base
1

7-22

Chapter 7 Optional AccessoriesC2000 Series


Conduit Box Installation

Frame D0
1.
Loosen the cover screws and press the tabs on each side of the cover to remove the cover, as shown in the
following figure. Screw torque: 12~15kg-cm (10.4~13 Ib-in)

2.

Remove the 5 screws shown in the following figure. Screw torque:24~26kg-cm (20.8~22.6Ib-in)

3.

Install the conduit box by fasten the 5 screws shown in the following figure.
Screw torque:24~26kg-cm (20.8~22.6Ib-in)

4.

Fasten the 2 screws shown in the following figure. Screw torque: 12~15kg-cm (10.4~13 Ib-in)

7-23

Chapter 7 Optional Accessories C2000 Series
Frame D
1.
Loosen the cover screws and press the tabs on each side of the cover to remove the cover, as shown in the
following figure. Screw torque: 12~15kg-cm (10.4~13 Ib-in)

2.

Remove the 5 screws shown in the following figure. Screw torque:24~26kg-cm (20.8~22.6Ib-in)

3.

Install the conduit box by fasten the 5 screws shown in the following figure.
Screw torque:24~26kg-cm (20.8~22.6Ib-in)

4.

Fasten the 2 screws shown in the following figure. Screw torque: 12~15kg-cm (10.4~13 Ib-in)

7-24

Chapter 7 Optional AccessoriesC2000 Series
Frame E
1. Loosen the 4 cover screws and lift the cover; Screw torque: 12~ 15 kg-cm (10.4~13Ib-in).

2. Fasten the 6 screws shown in the following figure and place the cover back to the original position. Screw
torque: 24~26kg-cm (20.8~22.6Ib-in).

3. Fasten the 4 screws shown in the following figure. Screw torque:12~15kg-cm (10.4~13Ib-in)』

7-25

Chapter 7 Optional Accessories C2000 Series
Frame F
1.

Loosen the cover screws and press the tabs on each side of the cover to remove the cover, as shown in the
following figure. Screw torque: 12~15kg-cm (10.4~13 Ib-in).

4

1
2

3

2.

Install the conduit box by fastens the 4 screws, as shown in the following figure.
Screw torque: 24~26kg-cm (20.8~22.6Ib-in).

5
7

8
6

3.

Install the conduit box by fasten all the screws shown in the following figure
Screw 9~12 torque: 12~15kg-cm (10.4~13.6Ib-in)
Screw 13~16 torque: 24~26kg-cm (20.8~22.6Ib-in)

12

15
9
10

13
14
16

11

7-26

Chapter 7 Optional AccessoriesC2000 Series
Frame G
1.
On the conduit box, loosen 7 of the cover screws and remove the cover「Screw torque: 24~26kg-cm
(20.8~22.6Ib-in)」. On the drive, loosen 4 of the cover screws and press the tabs on each side of the cover to
remove the cover, as shown in the following figure. Screw torque: 12~15kg-cm (10.4~13Ib-in).

4

1
2

3

Remove the top cover and loosen the screws.
M5 Screw torque: 24~26kg-cm (20.8~22.6Ib-in)
M8 Screw torque: 100~120kg-cm (86.7~104.1Ib-in)

2.

Install the conduit box by fastening all the screws shown in the following figure.
M5 Screw torque: 24~26kg-cm (20.8~22.6Ib-in)
M8 Screw torque: 100~120kg-cm (86.7~104.1Ib-in)

7-27

Chapter 7 Optional Accessories C2000 Series
Fasten all the screws. Screw torque: 24~26kg-cm (20.8~22.6Ib-in).

Place the cover back to the top and fasten the screws (as shown in the figure).
Screw torque: 12~15kg-cm (10.4~13Ib-in).

7-28

Chapter 7 Optional AccessoriesC2000 Series

7-10 Fan Kit


Frames of the fan kit

Frame A

Heat sink Fan Model『MKC-AFKM』

Applicable Model
VFD015C23A; VFD022C23A; VFD037C23A;VFD022C43A/43E;
VFD037C43A/43E;VFD040C43A/43E; VFD055C43A/43E

Frame B

Heat sink Fan Model『MKC-BFKM1』

Applicable Model
VFD055C23A; VFD075C43A/43E

Frame B

Heat sink Fan Model 『MKC-BFKM2』

Applicable Model
VFD075C23A; VFD110C23A; VFD110C43A/43E;
VFD150C43A/43E

Frame B

Capacitor Fan Model 『MKC-BFKB』

Applicable Model
VFD055C23A; VFD075C23A; VFD110C23A;VFD075C43A/43E;
VFD110C43A/43E;VFD150C43A/43E

7-29

Chapter 7 Optional Accessories C2000 Series
Frame C

Capacitor Fan Model 『MKC-CFKB1』

Applicable Model
VFD150C23A; VFD185C23A; VFD220C23A

Frame C

Capacitor Fan Model 『MKC-CFKB2』

Applicable Model
VFD185C43A/43E; VFD220C43A/43E;VFD300C43A/43E

Frame C

Heat sink Fan 『MKC-CFKM』

Following Model use one set of MKC-CFKM:
VFD185C43A/E; VFD220C43A/E; VFD300C43A
Following Model use two sets of MKC-CFKM
VFD150C23A; VFD185C23A; VFD220C23A; VFD300C43E

Frame D0

Heat sink Fan Model
『MKC-D0FKM』

Capacitor Fan Model
『MKC-DFKB』

Heat sink Fan Model
『MKC-DFKM』

Capacitor Fan Model
『MKC-DFKB』

Applicable Model
VFD370C43S/43U; VFD450C43S/43U;

Frame D
Applicable Model
VFD300C23A/23E; VFD370C23A/23E; VFD370C43A/43E;
VFD450C43A/43E; VFD550C43A/43E; VFD750C43A/43E

7-30

Chapter 7 Optional AccessoriesC2000 Series
Frame E

Heat sink Fan Model 『MKC-EFKM1』

Applicable Model
VFD450C23A/23E; VFD550C23A/23E

Frame E

Heat sink Fan Model『MKC-EFKM2』

Applicable Model
VFD750C23A/23E; VFD900C43A/43E; VFD1100C43A/43E

Frame E

Capacitor Fan Model 『MKC-EFKB』

Applicable Model
VFD450C23A/23E; VFD550C23A/23E; VFD750C23A/23E;
VFD900C43A/43E; VFD1100C43A/43E

Frame F

Heat sink Fan Model 『MKC-FFKM』

Applicable Model
VFD900C23A/23E; VFD1320C43A/43E; VFD1600C43A/43E
;

7-31

Chapter 7 Optional Accessories C2000 Series
Frame F

Capacitor Fan Model 『MKC-FFKB』

Applicable Model
VFD900C23A/23E; VFD1320C43A/43E; VFD1600C43A/43E

Frame G

Heat sink Fan Model 『MKC-GFKM』

Applicable Model
VFD1850C43A/43E; VFD2200C43A/43E

Frame H

Heat sink Fan Model 『MKC-HFKM』

Applicable Model
VFD2800C43A/43E; VFD3150C43A/43E; VFD3550C43A/43E;
VFD4500C43A/43E
VFD2800C43E-1; VFD3150C43E-1; VFD3550C43E-1;
VFD4500C43E-1

7-32

Chapter 7 Optional AccessoriesC2000 Series


Fan Removal

Frame A
Model『MKC-AFKM』: Heat Sink Fan
Applicable model
VFD015C23A; VFD022C23A; VFD022C43A/43E; VFD037C23A; VFD037C43A/43E; VFD040C43A/43E; VFD055C43A/43E
1. Refer to Figure 1, press the tabs on both side of the fan to 2. Disconnect the power terminal before removing the fan.
successfully remove the fan.
(As shown below.)

Figure 2

Figure 1
Frame B
Model『MKC-BFKM1』Heat Sink Fan
Applicable model
VFD055C23A; VFD075C43A/43E;VFD075C23A;
1. Refer to Figure 1, press the tab on both side of the fan to
successfully remove the fan.

2.

Disconnect the power terminal before removing the fan.
(As shown below.)

Figure 2

Figure 1
Frame B
Model『MKC-BFKM2』Heat Sink Fan

Applicable model
VFD075C23A; VFD110C23A; VFD110C43A/43E; VFD150C43A/43E
1. Refer to Figure 1, press the tab on both side of the fan to
2. Disconnect the power terminal before removing the fan.
successfully remove the fan.
(As shown below.)

Figure 1

Figure 2

7-33

Chapter 7 Optional Accessories C2000 Series
Frame B
Model『MKC-BFKB』Capacitor Fan
Applicable model
VFD055C23A; VFD075C23A; VFD075C43A/43E; VFD110C23A; VFD110C43A/43E;
VFD150C43A/43E
Disconnect fan power and pull out the fan by using flathead screwdriver. (As shown in the larger picture)

Frame C
Model『MKC-CFKM』Heat Sink Fan
Applicable model
Single fan kit applicable models (only fan kit 1 is required to be installed): VFD185C43A/E; VFD220C43A/E; VFD300C43A
Duo fan kit applicable models (both fan kit 1 and 2 are required to be installed): VFD150C23A; VFD185C23A; VFD220C23A;
VFD300C43E
1.

(As shown Figure 1) Before removing the fan, remove the cover by using a slotted screwdriver.

Figure 1

7-34

Chapter 7 Optional AccessoriesC2000 Series
2.

(As shown in Figure 2), remove the power connector, loosen the screw and remove the fan kit. When installing the fan kit,
have the label on the fan kit facing inside of the motor drive.
Screw’s torque force: 10~12kgf-cm (8.7~10.4(lb-in)

Figure 2
Frame C
Model『MKC-CFKB1』Capacitor Fan
Applicable model
VFD150C23A; VFD185C23A; VFD220C23A
Model『MKC-CFKB2』Capacitor Fan
Applicable model
VFD185C43A/43E; VFD220C43A/43E; VFD300C43A/43E
Disconnect fan power and pull out the fan by using flathead screwdriver. (As shown in the larger picture)

Figure 1

7-35

Chapter 7 Optional Accessories C2000 Series
Frame D0
Model 『MKC-DFKB』Capacitor Fan
Applicable model
VFD370C43S/43U; VFD450C43S/43U;
1. Loosen screw 1 and screw 2, press the tab on the right and 2.
left to remove the cover, follow the direction the arrows
indicate. Press on top of digital keypad to properly remove
it. Screw 1, 2『Torque :12~15kgf-cm (8.6~10.4lb-in)』

(Figure 2) Loosen screw 3, press the tab on the right and
the left to remove the cover. Screw 3『Torque : 6~8kgf-cm
(5.2~6.9lb-in)』

3

1
2

Figure 2

Figure 1
3.

Loosen screw 4 (figure 3) and disconnect fan power and
pull out the fan. (As shown in the enlarged picture 3)
Screw 4『Torque : 10~12kgf-cm (8.6~10.4lb-in)』

4

Figure 3
Frame D0
Model 『MKC-D0FKM』Heat Sink Fan
Applicable model
VFD370C43S/43U; VFD450C43S/43U;
1. Loosen the screw and remove the fan kit. 『Screw torque: 24~26kgf-cm (20.8~22.6lb-in)』
2. (As shown Figure 1) Before removing the fan, remove the cover by using a slotted screwdriver.

1
2
3
4

Figure 1

7-36

Chapter 7 Optional AccessoriesC2000 Series
Frame D
Model 『MKC-DFKB』Capacitor Fan
Applicable model
VFD300C23A/23E; VFD370C23A/23E; VFD550C43A/43E; VFD750C43A/43E;
1.

Loosen screw 1 and screw 2, press the on the right and the 2.
left to remove the cover, follow the direction the arrows
indicate. Press on top of digital keypad to properly remove
it. Screw 1, 2『Torque :12~15kgf-cm (10.4~13lb-in)』

(Figure 2) Loosen screw 3, press the tab on the right and
the left to remove the cover.
Screw 3, 4『Torque : 6~8kgf-cm (5.2~6.9lb-in)』

3

4

1
2

Figure 2

Figure 1
3.

Loosen screw 5 (figure 3) and disconnect fan power and pull out the fan. (As shown in the enlarged picture 3)
Screw 5『Torque :10~12kgf-cm (8.6~10.4lb-in)』

5

Figure 3
Frame D
Model『MKC-DFKM』Heat Sink Fan
Applicable model
VFD300C23A/23E; VFD370C23A/23E; VFD370C43A/43E; VFD450C43A/43E; VFD550C43A/43E; VFD750C43A/43E;
1.
2.

Loosen the screw and remove the fan kit. 『Screw torque: 24~26kgf-cm (20.8~22.6lb-in)』
(As shown Figure 1) Before removing the fan, remove the cover by using a slotted screwdriver.

1
2
3
4

Figure 1

7-37

Chapter 7 Optional Accessories C2000 Series
Frame E
Applicable model
VFD450C23A/23E; VFD550C23A/23E; VFD750C23A/23E; VFD900C43A/43E; VFD1100C43A/43E;
Model『MKC-EFKM1』Heat Sink Fan
1.

Model『MKC-EFKM2』Heat Sink Fan

Loosen screw 1~4 (figure 1) and disconnect fan power
1.
and pull out the fan. (As shown in the enlarged picture 3)
Screw1~4『Torque : 24~26kgf-cm (20.8~22.6lb-in)』

Loosen screw 1~4 (figure 2) and disconnect fan power
and pull out the fan. (As shown in the enlarged picture 3)
Screw1~4『Torque : 24~26kgf-cm (20.8~22.6lb-in)』

1

1

2

2
3

3

4

4

Figure 2

Figure 1
Model『MKC-EFKB』Capacitor Fan
1.

Loosen screw 1~2 (figure 3) and disconnect fan power and pull out the fan. (As shown in the enlarged picture 3)
Screw1~2『Torque : 24~26kgf-cm (20.8~22.6lb-in)』

1
2

Figure 3
Frame F
Applicable model
VFD900C23A/23E; VFD1320C43A/43E; VFD1600C43A/43E;
Fan model『MKC-FFKM』Heat Sink Fan
Loosen the screws and plug out the power of fan before removing (figure 1). Screw torque: 12~15kg-cm (10.4~13Ib-in)』

1
4

3
2

Figure 1

7-38

Chapter 7 Optional AccessoriesC2000 Series
Fan model 『MKC-FFKB』Capacitor Fan
(1) Loosen the screw (figure 1) and removes the cover.
torque: 14~16kg-cm (12.2~13.9Ib-in).

Screw (2) Loosen the screw (figure 2) and removes the cover. Screw
torque: 24~26kg-cm (20.8~22.6Ib-in).
7

5
8
4

6
1
3

2

Figure 1

Figure 2

(3) Loosen the screws and remove the fan. (figure 3 and figure 4) Screw torque: 24~26kg-cm (20.8~22.6Ib-in).

11
10
9

9

10

11

Figure 3

Figure 4

Frame G
Applicable model
VFD1800C43A/43E; VFD2200C43A/43E;
Fan model『MKC-GFKM』Heat Sink Fan
(1) Loosen the screw (figure 1) and remove the cover. Screw
torque: 12~15kg-cm (10.4~13Ib-in).

(2) For 1~8 shown in the figure 2: Loosen the screws
Screw torque:35~40kg-cm (30.4~34.7lb-in)
For 9~10 shown in the figure 2: Loosen the screws and
removes the cover.
Screw M4 torque: 14~16kg-cm (12.2~13.9 Ib-in).

9

4

1

10
6

3

7
8

2
1
4

2

3

5

Figure 1

Figure 2

7-39

Chapter 7 Optional Accessories C2000 Series
(3) Loosen screw 1,2,3 and remove the protective ring (as
(4) Lift the fan by putting your finger through the protective
holes, as indicates in 1 and 2 on the figure 4.
shown in figure 3) Screw torque: 14~16kg-cm (12.2~13.9 Ib-in).

4
1
2

5

1

3
2

.
Figure 4

Figure 3
Frame H
Applicable model
VFD2800C43A/43E; VFD3150C43A/43E; VFD3550C43A/43E; VD4500C43A/43E
Fan model 『MKC-HFKM』Heat Sink Fan
(1) Loosen the screw and remove the top cover (figure 1)
Screw torque: 14~16kg-cm (12.2~13.9Ib-in)

(2) Loosen the screw and remove the top cover (figure 2).
Screw torque: 24~26kg-cm (20.8~22.6Ib-in).

7

8
9
10
11
12

5
4

6
3
1

2

Figure 1

Figure 2

7-40

Chapter 7 Optional AccessoriesC2000 Series
(3) Disconnect the fan (figure 3).

(4) Loosen the screw and remove the fan. Make sure fan power
is properly disconnected before removal. Screw torque:
24~26kg-cm (20.8~22.6Ib-in). (figure 4)

15
15
14
13

Figure 3

18
17
16

14
13

Figure 4

7-41

18
17
16

Chapter 7 Optional Accessories C2000 Series

7-11 Flange Mounting Kit
Applicable Models, Frame A~F
Frame A
『MKC-AFM1』
Applicable model
VFD015C23A; VFD022C23A; VFD022C43A/43E

Screw 1 *4
M3*P 0.5; L=6mm
Screw 2*8
M6*P 1.0; L=16mm
Accessories 1*1

Accessories

2*2

Accessories 3*2

『MKC-AFM』
Applicable model
VFD007C23A; VFD007C43A/43E; VFD015C43A/43E; VFD037C23A; VFD037C43A/43E; VFD040C43A/43E;
VFD055C43A/43E

Screw *8
M6*P 1.0; L=16mm
Accessory 2*2

Accessory t 3*2

Cutout dimension

Unit: mm [inch]

7-42

Chapter 7 Optional AccessoriesC2000 Series

『MKC-AFM1』Installation
1.

Install accessory 1 by fastening 4 of the screw 1(M3) (figure 1). Screw torque: 6~8kg-cm (5.21~6.94Ib-in).

Figure 1

2.

Install accessory 2&3 by fastening 2 of the screw 2(M6) (figure 2). Screw torque: 25~30kg-cm (21.7~26Ib-in).

3.

Install accessory 2&3 by fastening 2 of the screw 2(M6) (figure 3). Screw torque: 25~30kg-cm (21.7~26Ib-in).

4.

Plate installation, place 4 of the screw 2 (M6) (figure 4) through accessory 2&3 and the plate then fasten the
screws. Screw torque: 25~30kg-cm (21.7~26Ib-in).

Figure 2

Figure 3

Figure 4

7-43

Chapter 7 Optional Accessories C2000 Series

『MKC-AFM』 Installation
1.

Fasten screw*2(M6) and accessory 2 &3. Screw torque: 25~30kg-cm (21.7~26Ib-in). (figure 1)

2.

Fasten screw*2(M6) and accessory 2 &3. Screw torque: 25~30kg-cm (21.7~26Ib-in). (figure 2)

3.

Plate installation, place 4 of the screw *4 (M6) through accessory 2&3 and the plate then fasten the screws.
Screw torque: 25~30kg-cm (21.7~26Ib-in). (figure 3)

Figure 1

Figure 2

Figure 3

7-44

Chapter 7 Optional AccessoriesC2000 Series

Frame B
『MKC-BFM』
Applicable model
VFD055C23A; VFD075C23A; VFD110C23A; VFD075C43A/43E; VFD110C43A/43E; VFD150C43A/43E

Screw 1 *4 ~ M8*P 1.25;
Screw 2*6 ~ M6*P 1.0;
Accessory 1*2

Accessory 2*2

Cutout dimension

Unit: mm [inch]

7-45

Chapter 7 Optional Accessories C2000 Series

『MKC-BFM』Installation
1.

Install accessory 1& 2 by fastening 4 of the screw 1(M8). Screw torque: 40~45kg-cm (34.7~39.0Ib-in).
(As shown in the following figure)

2.

Plate installation, place 6 of the screw 2 (M6) through accessory 1&2 and the plate then fasten the screws.
Screw torque: 25~30kg-cm (21.7~26Ib-in). (As shown in the following figure)

7-46

Chapter 7 Optional AccessoriesC2000 Series

Frame C
『MKC-CFM』
Applicable model
VFD150C23A; VFD185C23A; VFD220C23A; VFD185C43A/43E; VFD220C43A/43E; VFD300C43A/43E
Screw 1*4 ~ M8*P 1.25;
Screw 2*8 ~ M6*P 1.0;
Accessory 1*2

Accessory 2*2

Cutout dimension

Unit: mm [inch]

7-47

Chapter 7 Optional Accessories C2000 Series

『MKC-CFM』Installation
1.

Install accessory 1& 2 by fastening 4 of the screw 1(M8). Screw torque: 50~55kg-cm (43.4~47.7Ib-in).
(As shown in the following figure)

2.

Plate installation, place 8 of the screw 2 (M6) through Accessory 1&2 and the plate then fasten the screws.
Screw torque: 25~30kg-cm (21.7~26Ib-in). (As shown in the following figure)

7-48

Chapter 7 Optional AccessoriesC2000 Series

Frame D0
Applicable model
VFD370C43S/U; VFD450C43S/U
Cutout dimension

Unit: mm [inch]

M10*P1.5(4X)
OR 11.0[0.43](4X)

7-49

Chapter 7 Optional Accessories C2000 Series

Frame D
Applicable model
VFD300C23A/23E; VFD370C23A/23E; VFD550C43A/43E; VFD750C43A/43E
Cutout dimension

Unit: mm [inch]

M10*P1.5(4X)
OR 11.0[0.43](4X)

7-50

Chapter 7 Optional AccessoriesC2000 Series

Frame E
Applicable model
VFD450C23A/23E; VFD550C23A/23E; VFD750C23A/23E; VFD900C43A/43E; VFD1100C43A/43E;
Cutout dimension

Unit: mm [inch]

7-51

Chapter 7 Optional Accessories C2000 Series

Frame D0&D&E
1. Loosen 8 screws and remove Fixture 2 (as shown in 2. Loosen 10 screws and remove Fixture 1 (as shown
in the following figure).
the following figure).

3. Fasten 4 screws (as shown in the following figure).
Screw torque: 30~32kg-cm (26.0~27.8Ib-in).

4. Fasten 5 screws (as shown in the following figure).
Screw torque: 30~32kg-cm (26.0~27.8Ib-in).

5. Fasten 4 screws (as shown in the following figure).
Screw torque: 24~26kg-cm (20.8~22.6Ib-in).

6. Fasten 5 screws (as shown in the following figure).
Screw torque: 24~26kg-cm (20.8~22.6Ib-in).

7.

Place 4 screws (M10) through Fixture 1&2 and the
plate then fasten the screws. (as shown in the
following figure)
Frame D0/D M10*4
Screw torque: 200~240kg-cm (173.6~208.3Ib-in).
Frame E M12*4
Screw torque: 300~400kg-cm (260~347Ib-in).

7-52

Chapter 7 Optional AccessoriesC2000 Series

Frame F
Applicable model
VFD900C23A/23E; VFD1320C43A/43E; VFD1600C43A/43E
Cutout dimension

Unit: mm [inch]

M12*P1.75(4X)
OR 13.0[0.51](4X)

7-53

Chapter 7 Optional Accessories C2000 Series

Frame F
1. Loosen 12 screws and remove Fixture 2.

2. Loosen 12 screws and remove Fixture 2.
Screw torque: 24~26kg-cm (20.8~22.6Ib-in).

1

1
6
5

6
5

4
3
2

12
7

4
3
2

12
7

8
FIXTURE 2

8

9

FIXTURE2

10

9

11

10
11

3. Loosen screw 13 ~26 and remove Fixture 1.

4.

Install Fixture 1 by fasten screw 13 ~26
Screw torque: 24~26kg-cm (20.8~22.6Ib-in).

13
19
18
17

13
19
18
17

20

20

26

16

26

14

16
14
15

25

15

25

24

24

FIXTURE1

FIXTURE1

23

23
21
22

5.

Place 4 of the M12 screws through Fixture 1&2 and
plate then fasten the screws.
Screw torque: 300~400kg-cm (260~347Ib-in).
Screws M12*4

7-54

21

22

Chapter 7 Optional AccessoriesC2000 Series

7-12 USB/RS-485 Communication Interface IFD6530
Warning
 Please thoroughly read this instruction sheet before installation and putting it into use.
 The content of this instruction sheet and the driver file may be revised without prior notice. Please
consult our distributors or download the most updated instruction/driver version at
http://www.delta.com.tw/product/em/control/cm/control_cm_main.asp

1. Introduction
IFD6530 is a convenient RS-485-to-USB converter, which does not require external power-supply and complex
setting process. It supports baud rate from 75 to 115.2kbps and auto switching direction of data transmission. In
addition, it adopts RJ-45 in RS-485 connector for users to wire conveniently. And its tiny dimension, handy use of
plug-and-play and hot-swap provide more conveniences for connecting all DELTA IABU products to your PC.
Applicable Models: All DELTA IABU products.

(Application & Dimension)

2. Specifications
Power supply

No external power is needed

Power consumption

1.5W

Isolated voltage

2,500VDC

Baud rate

75, 150, 300, 600, 1,200, 2,400, 4,800, 9,600, 19,200, 38,400, 57,600, 115,200 bps

RS-485 connector

RJ-45

USB connector

A type (plug)

Compatibility

Full compliance with USB V2.0 specification

Max. cable length

RS-485 Communication Port: 100 m

Support RS-485 half-duplex transmission

7-55

Chapter 7 Optional Accessories C2000 Series
 RJ-45
PIN

Description

PIN

Description

1

Reserved

5

SG+

2

Reserved

6

GND

3

GND

7

Reserved

4

SG-

8

+9V

3. Preparations before Driver Installation
Please extract the driver file (IFD6530_Drivers.exe) by following steps. You could find driver file
(IFD6530_Drivers.exe) in the CD supplied with IFD6530.
Note: DO NOT connect IFD6530 to PC before extracting the driver file.
STEP 1

STEP 2

STEP 3

STEP 4

STEP 5
You should have a folder marked SiLabs under drive C. c:\ SiLabs

7-56

Chapter 7 Optional AccessoriesC2000 Series

4. Driver Installation
After connecting IFD6530 to PC, please install driver by following steps.

7-57

Chapter 7 Optional Accessories C2000 Series

5. LED Display
1. Steady Green LED ON: power is ON.
2. Blinking orange LED: data is transmitting.

7-58

Chapter 8 Optional Cards C2000 Series

Chapter 8 Option Cards
8-1 Removed Key Cover
8-2 Srews Specification for Option Card Terminals
8-3 EMC-D42A
8-4 EMC-D611A
8-5 EMC-R6AA
8-6 EMC-BPS01
8-7 EMC-PG01/02L
8-8 EMC-PG01/02O
8-9 EMC-PG01/02U
8-10 EMC-PG01R
8-11 CMC-MOD01
8-12 CMC-PD01
8-13 CMC-DN01
8-14 CMC-EIP01
8-15 EMC-COP01

8-1

Chapter 8 Optional Cards C2000 Series

Please select applicable option cards for your drive or contact local distributor for suggestion.
To prevent drive damage during installation, please removes the digital keypad and the cover before
wiring. Refer to the following instruction.

8-1 Removed key cover
Frame A&B&C
Screw Torque: 8~10Kg-cm [6.9~8.7lb-in.]

Frame D0
Screw Torque: 8~10Kg-cm [6.9~8.7lb-in.]

Frame D
Screw Torque: 8~10Kg-cm [6.9~8.7lb-in.]

8-2

Chapter 8 Optional Cards C2000 Series

Frame E
Slightly lift the cover then pull to remove. Screw Torque: 12~15Kg-cm [10.4~13lb-in.]

Frame F
Screw Torque: 12~ 15 Kg-cm [10.4~13lb-in.]

Frame G
Screw Torque: 12~15Kg-cm [10.4~13lb-in.]

8-3

Chapter 8 Optional Cards C2000 Series

Frame H
Screw Torque: 14~16Kg-cm [12.15~13.89lb-in.]

1 RJ45 (Socket) for digital keypad
KPC-CC01; KPC-CE01

1
3

Slot 3

Please refer to CH10 Digital Keypad for more details on
KPC-CE01.
Please refer to CH10 Digital Keypad for more details on
optional accessory RJ45 extension cable.

4

Slot 2 Slot 1

2

2 Communication extension card (Slot 1)
CMC-MOD01;

CMC-PD01;

CMC-DN01;

CMC-EIP01;

EMC-COP01;
3 I/O & Relay extension card (Slot 3)
EMC-D42A;

EMC-D611A;

EMC-R6AA;

EMC-BPS01;

4 PG Card (Slot 2)
EMC-PG01L; EMC-PG02L;
EMC-PG01O; EMC-PG02O;
EMC-PG01U; EMC-PG02U;
EMC-PG01R;

8-4

Chapter 8 Optional Cards C2000 Series

8-2 Screws Specification for option card terminals:
EMC-D42A

2
Wire gauge 24~12AWG（0.205~3.31mm ）

EMC-D611A
EMC-BPS01
EMC-R6AA

Torque

5Kg-cm [4.34Ib-in]

2
Wire gauge 26~16AWG（0.128~1.31mm ）

Torque

8Kg-cm [6.94Ib-in]

EMC-PG01L
EMC-PG01O

2
Wire gauge 30~16AWG（0.0509~1.31mm ）

EMC-PG01R

Torque

2Kg-cm [1.74Ib-in]

EMC-PG01U

I/O & Relay extension card (Slot 3)
EMC-D42A

EMC-R6AA

EMC-BPS01

EMC-D611A

8-5

Chapter 8 Optional Cards C2000 Series

PG card (Slot 2)
EMC-PG01O/ EMC-PG02O

EMC-PG01U/ EMC-PG02U

EMC-PG01L/ EMC-PG02L

EMC-PG01R

8-6

Chapter 8 Optional Cards C2000 Series

Communication extension card (Slot 1)
CMC-PD01

CMC-MOD01/ CMC-EIP01

CMC-DN01

EMC-COP01

8-7

Chapter 8 Optional Cards C2000 Series

PG Card intallation

8-8

Chapter 8 Optional Cards C2000 Series

Disconneting the extension card

8-9

Chapter 8 Optional Cards C2000 Series

8-3 EMC-D42A
Terminals
COM

MI10~ MI13

I/O Extension
Card

MO10~MO11

Descriptions
Common for Multi-function input terminals
Select SINK（NPN）/SOURCE（PNP）in J1 jumper / external power
supply
Refer to parameters 02-26~02-29 to program the multi-function
inputs MI10~MI13.
Internal power is applied from terminal E24: +24Vdc±5% 200mA,
5W
External power +24VDC: max. voltage 30VDC, min. voltage
19VDC, 30W
ON: the activation current is 6.5mA
OFF: leakage current tolerance is 10μA
Multi-function output terminals (photocoupler)
The AC motor drive releases various monitor signals, such as drive
in operation, frequency attained and overload indication, via
transistor (open collector).
MO10
MO11
MXM

MXM

Common for multi-function output terminals MO10,
MO11(photocoupler)
Max 48VDC 50mA

8-4 EMC-D611A

I/O Extension
Card

Terminals
AC

Descriptions
AC power Common for multi-function input terminal (Neutral)

MI10~ MI15

Refer to Pr. 02.26~ Pr. 02.31 for multi-function input selection
Input voltage: 100~130VAC
Input frequency: 47~63Hz
Input impedance: 27Kohm
Terminal response time:
ON: 10ms
OFF: 20ms

8-5 EMC-R6AA
Terminals

Descriptions
Refer to Pr. 02.36~ Pr. 02.41 for multi-function input selection
Resistive load:
5A(N.O.) 250VAC

Relay Extension
Card

R10A~R15A
R10C~R15C

5A(N.O.) 30VDC
Inductive load (COS 0.4)
2.0A(N.O.) 250VAC
2.0A(N.O.) 30VDC
It is used to output each monitor signal, such as drive is in
operation, frequency attained or overload indication.

8-10

Chapter 8 Optional Cards C2000 Series

8-6 EMC-BPS01
Terminals

Descriptions
Input power: 24V±5%
Maximum input current:0.5A

External Power
Supply

Note:
24V
GND

1) Do not connect control terminal +24V (Digital control signal common:
SOURCE) directly to the EMC-BPS01input terminal 24V.
2) Do not connect control terminal GND directly to the EMC-BPS01 input
termina GND.

Note: Refer to I/O & Rlay extension card installation/ disconnecting method for PG Card installation/ disconnecting.

8-11

Chapter 8 Optional Cards C2000 Series

8-7 EMC-PG01L/EMC-PG02L


Terminal description
Set by Pr.10-00~10-02, 10-16~10-18
Terminals

Descriptions
Output voltage for power: +5V/+12V5% (use FSW3 to switch
+5V/+12V)
Max. output current: 200mA

VP
DCM

PG1

Common for power and signal
Encoder input signal (Line Driver or Open Collector)

A1, /A1, B1,
/B1, Z1, /Z1

A2, /A2,
B2, /B2

PG2

PG OUT

AO, /AO,
BO, /BO,
ZO, /ZO,

Open Collector input voltage: +5~+24V (Note 1)

It can be 1-phase or 2-phase input.

EMC-PG01L: Max. input frequency: 300kHz
EMC-PG02L: Max. input frequency: 30kHz(Note 2)
Pulse Input signal (Line Driver or Open Collector)
Open Collector input voltage: +5~+24V (Note1)

It can be 1-phase or 2-phase input.

EMC-PG01L: Max. input frequency: 300kHz
EMC-PG02L: Max. input frequency: 30kHz(Note 2)

PG Card Output signals. It has division frequency function: 1~255
times
Max. output voltage for Line driver: 5VDC
Max. output current: 50mA

EMC-PG01L Max. output frequency: 300kHz
EMC-PG02L Max. output frequency: 30kHz
SG is the GND of PG card. It is also the GND of position machine or
PLC to make the ouput signal to be the common pivot point.
Note 1: Open Collector application, input current 5~15mA to each set then each set needs one pull-up resistor.
If input voltage of open collector is 24V, the power of encoder needs to be connected externally. Please refer
diagram 2 of PG1.
SG,

5V
12V
24V

Recommended pull-up resistor: above100~220, 1/2W
Recommended pull-up resistor: above 510~1.35k, 1/2W
Recommended pull-up resistor, above1.8k~3.3k, 1/2W

Note 2: If the required bandwidth is not over 30kHz at the application, it is recommended to use
EMC-PG02O/L (bandwidth 30kHz) to avoid interference.

PG1 card wiring diagram (the image 1 and 2 below are wiring diagrams of Open Collector encoder)

8-12

Chapter 8 Optional Cards C2000 Series

PG2 Wiring Diagram

8-13

Chapter 8 Optional Cards C2000 Series



EMC-PG01L/EMC-PG02L Wiring Diagram


Please use a shielded cable to prevent interference. Do not run control wires parallel to any high voltage
AC power line (200 V and above).



Recommended wire size 0.21 to 0.81mm (AWG24 to AWG18).



Cable length: Less than 100m

2

8-14

Chapter 8 Optional Cards C2000 Series

8-8 EMC-PG01O/EMC-PG02O


Terminal descriptions
Set by Pr.10-00~10-02, 10-16~10-18
Terminals
VP
DCM

Descriptions
Output voltage for power: +5V/+12V5% (use FSW3 to switch +5V/+12V)
Max. output current: 200mA
Common for power and signal
Encoder Input signal (Line Driver or Open Collector)

PG1
A1, /A1, B1,
/B1, Z1, /Z1

Open Collector Input Voltage: +5V~+24V (Note 1)
It can be 1-phase or 2-phase input.
EMC-PG01O Max. input frequency: 300kHz
EMC-PG02O Max. input frequency: 30kHz(Note 2)
Pulse Input Signal (Line Driver or Open Collector)

PG2

A2, /A2,
B2, /B2

Open Collector Input Voltage: +5~+24V (Note 1)
EMC-PG01O Max. input frequency: 300kHz
EMC-PG02O Max. input frequency: 30kHz(Note 2)

V+, V+
V-

PG OUT

Needs external power source for PG OUT circuit.
Input voltage of power:+12V ~ +24V
Input voltage for the negative side

PG Card Output signals has division frequency function: 1~255 times.
On the open collector’s output signal, add a high-pull resistor on the external
power V+ ~ V- (e.g. power of PLC) to prevent the interference of the receiving
A/O, B/O, Z/O signal. Max. 。[Three pull-up resistor are included in the package (1.8kW/1W)]
(Note 1)
EMC-PG01O Max. input frequency: 300kHz

EMC-PG02O Max. input frequency: 30kHz
Note 1: Open Collector application, input current 5~15mA to each set then each set needs one pull-up resistor.
If input voltage of open collector is 24V, the power of encoder needs to be connected externally. Please refer
diagram 2 of PG1.
5V
12V
24V

Recommended pull-up resistor: above100~220, 1/2W
Recommended pull-up resistor: above 510~1.35k, 1/2W
Recommended pull-up resistor, above1.8k~3.3k, 1/2W

Note 2: If the required bandwidth is not over 30kHz at the application, it is recommended to use
EMC-PG02O/L (bandwidth 30kHz) to avoid interference.

PG1 card wiring diagram (the image 1 and 2 below are wiring diagrams of Open Collector encoder)

8-15

Chapter 8 Optional Cards C2000 Series

PG2 Wiring Diagram

8-16

Chapter 8 Optional Cards C2000 Series



EMC-PG01O/EMC-PG02O Wiring Diagram


Please use a shielded cable to prevent interference. Do not run control wires parallel to any high voltage
AC power line (200 V and above).



Recommended wire size 0.21 to 0.81mm (AWG24 to AWG18).



Cable length: Less than 30m

2

8-17

Chapter 8 Optional Cards C2000 Series

8-9 EMC-PG01U/ EMC-PG02U
 FSW1 S: Standard UVW Output Encoder; D: Delta Encoder
 When using the Delta Encoder, wait for at least 250ms after powering up to receive signals from UVW.
If a running command is received before UVW signals finish, a PGF5 error message will be given. So
wait for 250ms before sending a running command.
 EMC-PG02U has encoder disconnection detection function.
 Set by Pr.10-00~10-02, 10-16~10-18
Terminals
VP

PG1

DCM

Descriptions
Output voltage for power: +5V/+12V5% (use FSW3 to
switch +5V/+12V)
Max. output current: 200mA
Common for power and signal

Encoder input signal (Line Driver)
A1, /A1, B1, /B1, Z1, /Z1 It can be 1-phase or 2-phase input.
Max. output frequency: 300kP/sec
U1, /U1, V1, /V1, W1, /W1 Encoder input signal

PG2

A2, /A2,
B2, /B2

PG OUT

AO, /AO, BO, /BO, ZO,
/ZO, SG

Pulse Input signal (Line Driver or Open Collector)
Open Collector Input Voltage: +5~+24V (Note1)
It can be 1-phase or 2-phase input.
Max. output frequency: 300kP/sec.
PG Card Output signals.
It has division frequency function: 1~255 times
Max. output voltage for Line driver: 5Vdc
Max. output current: 50mA
Max. output frequency: 300kP/sec

SG is the GND of PG card. It is also the GND of position
machine or PLC to make the ouput signal to be the common
pivot point.
Note 1: Open Collector application, input current 5~15mA to each set then each set needs one pull-up resistor.
5V
12V
24V

Recommended pull-up resistor: above100~220, 1/2W
Recommended pull-up resistor: above 510~1.35k, 1/2W
Recommended pull-up resistor, above1.8k~3.3k, 1/2W

PG2 Wiring Diagram

8-18

Chapter 8 Optional Cards C2000 Series



EMC-PG01U Wiring Diagram


Please use a shielded cable to prevent interference. Do not run control wires parallel to any high voltage
AC power line (200 V and above).



Recommended wire size 0.21 to 0.81mm (AWG24 to AWG18).



Cable length: Less than 30m

2

8-19

Chapter 8 Optional Cards C2000 Series

8-10 EMC-PG01R


Terminal Descriptions
Set by Pr.10-00~10-02
Terminals
R1- R2

PG1

S1, /S3,
S2, /S4,

A2, /A2,
B2, /B2

PG2

PG OUT

AO, /AO,
BO, /BO,
ZO, /ZO,
SG,

Descriptions
Resolver Output Power
7Vrms, 10kHz
Resolver Input Signal (S2, /S4=Sin; S1, /S3=Cos)
3.5±0.175Vrms, 10kHz
Pulse Input signal (Line Driver or Open Collector)
Open Collector Input Voltage: +5~+24V (Note1)

It can be 1-phase or 2-phase input.
Max. output frequency: 300kP/sec.
PG Card Output signals. It has division frequency function: 1~255
times
Max. output voltage for Line driver: 5VDC
Max. output current: 50mA
Max. output frequency: 300kP/sec

SG is the GND of PG card. It is also the GND of position machine or PLC to
make the ouput signal to be the common pivot point.
Note 1: Open Collector application, input current 5~15mA to each set then each set needs one pull-up resistor.
5V
12V
24V

Recommended pull-up resistor: above100~220, 1/2W
Recommended pull-up resistor: above 510~1.35k, 1/2W
Recommended pull-up resistor, above1.8k~3.3k, 1/2W

PG2 Wiring Diagram





DOS(Degradation of Signal)：If the amplitude of the sine wave input of the S1-/S3/ S2-/S4 is lower than or higher than
the encoder IC’s specification, a red light will be on. The possible reasons which cause this problem are the following.
1.

The turns ratio of the resolver encoder is not 1:0.5 which makes the sine wave input of the S1-/S3/S2-/S4 not
equal to 3.5±0.175Vrms.

2.

While motor is running, motor creates common mode noise which makes accumulated voltage to be more than
3.5±0.175Vrms

LOT(Loss of Tracking): Compare the angle of S1-/S3/S2-/S4 sine wave input to the R1-R2 cosine wave. If their
difference is more than 5 degree, a red light will be on. Here are the possible reasons why that happens:
1.

The output frequency of the PG card is incorrect.

2.

The specification of Resolver’s encoder is not 10KHz

3.

The motor creates common mode noise while it is running. That causes a big difference, while the motor is
rotating, between main winding’s cosine wave angle and the sine wave angle of second and third windings.

8-20

Chapter 8 Optional Cards C2000 Series



EMC-PG01R Wiring Diagram


Please use a shielded cable to prevent interference. Do not run control wires parallel to any high voltage
AC power line (200 V and above).



Recommended wire size 0.21 to 0.81mm (AWG24 to AWG18).



Cable length: Less than 100m

2

8-21

Chapter 8 Optional Cards C2000 Series

8-11 CMC-MOD01


Features
1.
2.
3.
4.
5.
6.



Supports Modbus TCP protocol
MDI/MDI-X auto-detect
Baud rate: 10/100Mbps auto-detect
E-mail alarm
AC motor drive keypad/Ethernet configuration
Virtual serial port.

Product File



I/O CARD & Relay Card



PG Card



Comm. Card



RJ-45 connection port



Removable control circuit
terminal



Specifications
Network Interface
Interface
Number of ports
Transmission method

RJ-45 with Auto MDI/MDIX
1 Port
IEEE 802.3, IEEE 802.3u

Transmission cable

Category 5e shielding 100M

Transmission speed

10/100 Mbps Auto-Detect

Network protocol

ICMP, IP, TCP, UDP, DHCP, HTTP, SMTP, MODBUS OVER TCP/IP,
Delta Configuration

Electrical Specification
Power supply voltage

5VDC (supply by the AC motor drive)

Insulation voltage

2KV

Power consumption

0.8W

Weight

25g

8-22

Chapter 8 Optional Cards C2000 Series

Environment



Noise immunity

ESD (IEC 61800-5-1, IEC 61000-4-2)
EFT (IEC 61800-5-1, IEC 61000-4-4)
Surge Test (IEC 61800-5-1, IEC 61000-4-5)
Conducted Susceptibility Test (IEC 61800-5-1, IEC 61000-4-6)

Operation/storage

Operation: -10°C ~ 50°C (temperature), 90% (humidity)
Storage: -25°C ~ 70°C (temperature), 95% (humidity)

Vibration/shock immunity

International standard: IEC 61800-5-1, IEC 60068-2-6/IEC
61800-5-1, IEC 60068-2-27

Install CMC-MOD01 to VFD-C2000
1.
2.
3.

4.

Switch off the power supply of VFD-C2000.
Open the front cover of VFD-C2000.
Place the insulation spacer into the positioning pin at Slot 1 (shown in Figure 3), and aim the
two holes on the PCB at the positioning pin. Press the pin to clip the holes with the PCB (shown
in Figure 4).
Screw up at torque 6 ~ 8 kg-cm (5.21 ~ 6.94 in-lbs) after the PCB is clipped with the holes
(shown in Figure 5).
Slot 3

Slot 2 Slot 1

[Figure 3]

[Figure 4]

[Figure 5]



Communication Parameters for VFD-C2000 Connected to Ethernet
When VFD-C2000 is link to Ethernet, please set up the communication parameters base on the
table below. Ethernet master will be able to read/write the frequency word and control word of
VFD-C2000 after communication parameters setup.
Parameter
P00-20
P00-21

Function
Source of frequency
command setting
Source of operation
command setting

Set value (Dec)
8
5

8-23

Explanation
The frequency command is controlled by
communication card.
The operation command is controlled by
communication card.

Chapter 8 Optional Cards C2000 Series
Decoding method for
communication
IP setting
IP address -1
IP address -2
IP address -3
IP address -4
Netmask -1
Netmask -2
Netmask -3
Netmask -4
Default gateway -1
Default gateway -2
Default gateway -3
Default gateway -4

P09-30
P09-75
P09-76
P09-77
P09-78
P09-79
P09-80
P09-81
P09-82
P09-83
P09-84
P09-85
P09-86
P09-87



0
0
192
168
1
5
255
255
255
0
192
168
1
1

Decoding method for Delta AC motor
drive
Static IP(0) / Dynamic distribution IP(1)
IP address 192.168.1.5
IP address 192.168.1.5
IP address 192.168.1.5
IP address 192.168.1.5
Netmask 255.255.255.0
Netmask 255.255.255.0
Netmask 255.255.255.0
Netmask 255.255.255.0
Default gateway 192.168.1.1
Default gateway 192.168.1.1
Default gateway 192.168.1.1
Default gateway 192.168.1.1

Disconnecting CMC- MOD01 from VFD-C2000
1.
2.
3.
4.

Switch off the power supply of VFD-C2000.
Remove the two screws (shown in Figure 6).
Twist opens the card clip and inserts the slot type screwdriver to the hollow to prize the PCB off
the card clip (shown in Figure 7).
Twist opens the other card clip to remove the PCB (shown in Figure 8).

[Figure 6]

[Figure 7]

[Figure 8]


Basic Registers
BR#

R/W

Content

#0

R

#1

R

#2

R

#11

R/W

Modbus Timeout Pre-defined setting: 500 (ms)

#13

R/W

Keep Alive Time Pre-defined setting: 30 (s)

Model name

Explanation
Set up by the system; read only. The model code of
CMC-MOD01=H’0203

Firmware
version

Displaying the current firmware version in hex, e.g. H’0100 indicates the
firmware version V1.00.
Displaying the data in decimal form. 10,000s digit and 1,000s digit are for
Release date of
“month”; 100s digit and 10s digit are for “day”.
the version
For 1 digit: 0 = morning; 1 = afternoon.

8-24

Chapter 8 Optional Cards C2000 Series



LED Indicator & Troubleshooting
LED Indicators
LED
POWER

LINK

Status
Green

Green

How to correct it?

On

Power supply in normal status

--

Off

No power supply

Check the power supply

On

Network connection in normal status

--

Network in operation

--

Network not connected

Check if the network cable is
connected

Flashes
Off

Indication

Troubleshooting
Abnormality

Cause

How to correct it?

CMC-MOD01 not connected
to AC motor drive
CMC-MOD01 not connected
to network

Check if AC motor drive is powered, and if the
power supply is normal.
Make sure CMC-MOD01 is connected to AC motor
drive.
Make sure the network cable is correctly connected
to network.

Poor contact to RJ-45
connector

Make sure RJ-45 connector is connected to
Ethernet port.

CMC-MOD01 not connected
to network

Make sure CMC-MOD01 is connected to network.

AC motor drive not powered
POWER LED off

LINK LED off

No module found

Fail to open
CMC-MOD01 setup
page

Able to open
CMC-MOD01 setup
page but fail to
utilize webpage
monitoring
Fail to send e-mail

PC and CMC-MOD01 in
different networks and
blocked by network firewall.
CMC-MOD01 not connected
to network
Incorrect communication
setting in DCISoft
PC and CMC-MOD01 in
different networks and
blocked by network firewall.

Search by IP or set up relevant settings by AC
motor drive keypad.
Make sure CMC-MOD01 is connected to the
network.
Make sure the communication setting in DCISoft is
set to Ethernet.
Conduct the setup by AC motor drive keypad.

Incorrect network setting in
CMC-MOD01

Check if the network setting for CMC-MOD01 is
correct. For the Intranet setting in your company,
please consult your IT staff. For the Internet setting
in your home, please refer to the network setting
instruction provided by your ISP.
Check if the network setting for CMC-MOD01 is
correct.

Incorrect mail server setting

Please confirm the IP address for SMTP-Server.

Incorrect network setting in
CMC-MOD01

8-25

Chapter 8 Optional Cards C2000 Series

8-12 CMC-PD01


Features
1.
2.
3.
4.



Supports PZD control data exchange.
Supports PKW polling AC motor drive parameters.
Supports user diagnosis function.
Auto-detects baud rates; supports Max. 12Mbps.

Product Profile

1. NET indicator
2. POWER indicator
3. Positioning hole
4. AC motor drive connection
port
5. PROFIBUS DP connection
port
6. Screw fixing hole
7. Fool-proof groove



Specifications
PROFIBUS DP Connector
Interface

DB9 connector

Transmission method

High-speed RS-485

Transmission cable

Shielded twisted pair cable

Electrical isolation

500VDC

Communication
Message type

Cyclic data exchange

Module name

CMC-PD01

GSD document

DELA08DB.GSD

Company ID

08DB (HEX)

Serial transmission
speed supported
(auto-detection)

9.6kbps; 19.2kbps; 93.75kbps; 187.5kbps; 125kbps; 250kbps; 500kbps; 1.5Mbps;
3Mbps; 6Mbps; 12Mbps (bit per second)

Electrical Specification
Power supply

5VDC (supplied by AC motor drive)

Insulation voltage

500VDC

Power consumption

1W

Weight

28g

8-26

Chapter 8 Optional Cards C2000 Series

Environment



Noise immunity

ESD(IEC 61800-5-1,IEC 6100-4-2)
EFT(IEC 61800-5-1,IEC 6100-4-4)
Surge Teat(IEC 61800-5-1,IEC 6100-4-5)
Conducted Susceptibility Test(IEC 61800-5-1,IEC 6100-4-6)

Operation /storage

Operation: -10ºC ~ 50ºC (temperature), 90% (humidity)
Storage: -25ºC ~ 70ºC (temperature), 95% (humidity)

Shock / vibration
resistance

International standards: IEC61131-2, IEC68-2-6 (TEST Fc)/IEC61131-2 & IEC
68-2-27 (TEST Ea)

Installation
PROFIBUS DP Connector



PIN

PIN name

Definition

1

-

Not defined

2

-

Not defined

3

Rxd/Txd-P

Sending/receiving data P(B)

4

-

Not defined

5

DGND

Data reference ground

6

VP

Power voltage – positive

7

-

Not defined

8

Rxd/Txd-N

Sending/receiving data N(A)

9

-

Not defined

9

5

6

1

LED Indicator & Troubleshooting
There are 2 LED indicators on CMC-PD01. POWER LED displays the status of the working
power. NET LED displays the connection status of the communication.
POWER LED
LED status

How to correct it?

Indication

Green light on

Power supply in normal status.

--

Off

No power

Check if the connection between CMC-PD01 and AC
motor drive is normal.

NET LED
LED status

How to correct it?

Indication

Green light on

Normal status

--

Red light on

CMC-PD01 is not connected to
PROFIBUS DP bus.

Connect CMC-PD01 to PROFIBUS DP bus.

Red light
flashes

Invalid PROFIBUS communication
address

Set the PROFIBUS address of CMC-PD01 between 1 ~
125 (decimal)

Orange light
flashes

CMC-PD01 fails to communication
with AC motor drive.

Switch off the power and check whether CMC-PD01 is
correctly and normally connected to AC motor drive.

8-27

Chapter 8 Optional Cards C2000 Series

8-13 CMC-DN01


Functions
1.
2.
3.
4.
5.
6.
7.



Based on the high-speed communication interface of Delta HSSP protocol, able to conduct
immediate control to AC motor drive.
Supports Group 2 only connection and polling I/O data exchange.
For I/O mapping, supports Max. 32 words of input and 32 words of output.
Supports EDS file configuration in DeviceNet configuration software.
Supports all baud rates on DeviceNet bus: 125kbps, 250kbps, 500kbps and extendable serial
transmission speed mode.
Node address and serial transmission speed can be set up on AC motor drive.
Power supplied from AC motor drive.

Product Profile

1. NS indicator
2. MS indicator
3. POWER indicator
4. Positioning hole
5. DeviceNet connection port
6. Screw fixing hole
7. Fool-proof groove
8. AC motor drive connection
port


Specifications
DeviceNet Connector
Interface

5-PIN open removable connector. Of 5.08mm PIN interval

Transmission
th d
Transmission cable

CAN

Transmission speed
Network protocol

Shielded twisted pair cable (with 2 power cables)
125kbps, 250kbps, 500kbps and extendable serial transmission speed
d
DeviceNet protocol

AC Motor Drive Connection Port
Interface

50 PIN communication terminal

Transmission method

SPI communication

Terminal function

1. Communicating with AC motor drive
2. Transmitting power supply from AC motor drive

Communication
t
l

Delta HSSP protocol

8-28

Chapter 8 Optional Cards C2000 Series

Electrical Specification
Power supply voltage

5VDC (supplied by AC motor drive)

Insulation voltage

500VDC

Communication wire
power consumption

0.85W

Power consumption

1W

Weight

23g

Environment

Noise immunity

ESD (IEC 61800-5-1,IEC 6100-4-2)
EFT (IEC 61800-5-1,IEC 6100-4-4)
Surge Teat(IEC 61800-5-1,IEC 6100-4-5)
Conducted Susceptibility Test (IEC 61800-5-1,IEC 6100-4-6)

Operation /storage

Operation: -10ºC ~ 50ºC (temperature), 90% (humidity)
Storage: -25ºC ~ 70ºC (temperature), 95% (humidity)

Shock / vibration
resistance

International standards: IEC61131-2, IEC68-2-6 (TEST Fc)/IEC61131-2 &
IEC 68-2-27 (TEST Ea)

DeviceNet Connector



PIN

Signal

Color

Definition

1

V+

Red

DC24V

2

H

White

Signal+

3

S

-

Earth

4

L

Blue

Signal-

5

V-

Black

0V

1
2
3
4
5

LED Indicator & Troubleshooting
There are 3 LED indicators on CMC-DN01. POWER LED displays the status of power supply.
MS LED and NS LED are dual-color LED, displaying the connection status of the communication
and error messages.
POWER LED
LED status

Indication

How to correct it?

On

Power supply in abnormal status.

Check the power supply of CMC-DN01.

Off

Power supply in normal status

--

8-29

Chapter 8 Optional Cards C2000 Series

NS LED
LED status

Indication

How to correct it?

Off

No power supply or CMC-DN01 has
not completed MAC ID test yet.

1. Check the power of CMC-DN01 and see if the
connection is normal.
2. Make sure at least one or more nodes are on the
bus.
3. Check if the serial transmission speed of
CMC-DN01 is the same as that of other nodes.

Green light
flashes

CMC-DN01 is on-line but has not
established connection to the master.

1. Configure CMC-DN01 to the scan list of the
master.
2. Re-download the configured data to the master.

Green light on

CMC-DN01 is on-line and is normally
connected to the master

--

Red light
flashes

CMC-DN01 is on-line, but I/O
connection is timed-out.

1. Check if the network connection is normal.
2. Check if the master operates normally.

1.
2.
3.
4.

1. Make sure all the MAC IDs on the network are
not repeated.
2. Check if the network installation is normal.
3. Check if the baud rate of CMC-DN01 is
consistent with that of other nodes.
4. Check if the node address of CMC-DN01 is
illegal.
5. Check if the network power supply is normal.

Red light on

The communication is down.
MAC ID test failure.
No network power supply.
CMC-DN01 is off-line.

MS LED
LED status

Indication

How to correct it?

Off

No power supply or being off-line

Check the power supply of CMC-DN01 and see of
the connection is normal.

Green light
flashes

Waiting for I/O data

Switch the master PLC to RUN status

Green light on

I/O data are normal

--

Red light
flashes

Mapping error

1. Reconfigure CMC-DN01
2. Re-power AC motor drive

Red light on

Hardware error

1. See the error code displayed on AC motor drive.
2. Send back to the factory for repair if necessary.

Orange light
flashes

If the flashing lasts for a long time, check if
CMC-DN01 is establishing connection
CMC-DN01 and AC motor drive are correctly
with AC motor drive.
installed and normally connected to each other.

8-30

Chapter 8 Optional Cards C2000 Series

8-14 CMC-EIP01




Features
1.

Supports Modbus TCP and Ethernet/IP protocol

2.

MDI/MDI-X auto-detect

3.

Baud rate: 10/100Mbps auto-detect

4.

AC motor drive keypad/Ethernet configuration

5.

Virtual serial port

Product Profile
[Figure1]
1. Screw fixing hole
2. Positioning hole
3. AC motor drive connection
port
4. LINK indicator
5. RJ-45 connection port
6. POWER indicator
7. Fool-proof groove



Specifications
Network Interface
Interface

RJ-45 with Auto MDI/MDIX

Number of ports

1 Port

Transmission method

IEEE 802.3, IEEE 802.3u

Transmission cable

Category 5e shielding 100M

Transmission speed

10/100 Mbps Auto-Detect

Network protocol

ICMP, IP, TCP, UDP, DHCP, HTTP, SMTP, MODBUS OVER TCP/IP, EtherNet/IP, Delta
Configuration

Electrical Specification
Weight

25g

Insulation voltage

500VDC

Power consumption

0.8W

Power supply voltage

5VDC

8-31

Chapter 8 Optional Cards C2000 Series

Environment



Noise immunity

ESD (IEC 61800-5-1,IEC 61000-4-2)
EFT (IEC 61800-5-1,IEC 61000-4-4)
Surge Test (IEC 61800-5-1,IEC 61000-4-5)
Conducted Susceptibility Test (IEC 61800-5-1,IEC 61000-4-6)

Operation/storage

Operation: -10°C ~ 50°C (temperature), 90% (humidity)
Storage: -25°C ~ 70°C (temperature), 95% (humidity)

Vibration/shock
immunity

International standard: IEC 61800-5-1, IEC 60068-2-6/IEC 61800-5-1, IEC 60068-2-27

Installation
Connecting CMC-EIP01 to Network
1. Turn off the power of AC motor drive.
2. Open the cover of AC motor drive.
3. Connect CAT-5e network cable to RJ-45 port on
CMC-EIP01 (See Figure 2).
[Figure 2]
RJ-45 PIN Definition



PIN

Signal

Definition

PIN

Signal

Definition

1

Tx+

Positive pole for
data transmission

5

--

N/C

2

Tx-

Negative pole for
data transmission

6

Rx-

Negative pole for
data receiving

3

Rx+

Positive pole for
data receiving

7

--

N/C

4

--

N/C

8

--

N/C

Connecting CMC-EIP01 to VFD-C2000
1.
2.
3.

4.

Switch off the power of AC motor drive.
Open the front cover of AC motor drive.
Place the insulation spacer into the positioning pin at Slot 1 (shown in Figure 3), and aim the
two holes on the PCB at the positioning pin. Press the pin to clip the holes with the PCB (see
Figure 4).
Screw up at torque 6 ~ 8 kg-cm (5.21 ~ 6.94 in-lbs) after the PCB is clipped with the holes (see
Figure 5).

8-32

Chapter 8 Optional Cards C2000 Series

Slot 3

Slot 2 Slot 1

[Figure 3]

[Figure 4]

[Figure 5]


Communication Parameters for VFD-C2000 Connected to Ethernet
When VFD-C2000 is connected to Ethernet network, please set up the communication
parameters for it according to the table below. The Ethernet master is only able to read/write the
frequency word and control word of VFD-C2000 after the communication parameters are set.
Parameter
(Dec)

Function

Set value (Dec)

Explanation

P00-20

Source of frequency
command setting

8

The frequency command is controlled by
communication card.

P00-21

Source of operation
command setting

5

The operation command is controlled by
communication card.

P09-30

Decoding method for
communication

0

The decoding method for Delta AC motor
drive

P09-75

IP setting

0

Static IP(0) / Dynamic distribution IP(1)

P09-76

IP address -1

192

IP address 192.168.1.5

P09-77

IP address -2

168

IP address 192.168.1.5

P09-78

IP address -3

1

IP address 192.168.1.5

P09-79

IP address -4

5

IP address 192.168.1.5

P09-80

Netmask -1

255

Netmask 255.255.255.0

P09-81

Netmask -2

255

Netmask 255.255.255.0

P09-82

Netmask -3

255

Netmask 255.255.255.0

P09-83

Netmask -4

0

Netmask 255.255.255.0

P09-84

Default gateway -1

192

Default gateway 192.168.1.1

P09-85

Default gateway -2

168

Default gateway 192.168.1.1

P09-86

Default gateway -3

1

Default gateway 192.168.1.1

P09-87

Default gateway -4

1

Default gateway 192.168.1.1

8-33

Chapter 8 Optional Cards C2000 Series



Disconnecting CMC- EIP01 from VFD-C2000
1. Switch off the power supply of VFD-C2000.
2. Remove the two screws (see Figure 6).
3. Twist opens the card clip and inserts the slot type screwdriver to the hollow to prize the PCB off the
card clip (see Figure 7).
4. Twist opens the other card clip to remove the PCB (see Figure 8).

[Figure 6]

[Figure 7]

[Figure 8]


LED Indicator & Troubleshooting
There are 2 LED indicators on CMC-EIP01. The POWER LED displays the status of power
supply, and the LINK LED displays the connection status of the communication.
LED Indicators
LED
POWER

LINK

Status
Green

Green

Indication

How to correct it?

On

Power supply in normal status

--

Off

No power supply

Check the power supply.

On

Network connection in normal
status

--

Network in operation

--

Network not connected

Check if the network cable is
connected.

Cause

How to correct it?

Flashes
Off

Troubleshooting
Abnormality

CMC-EIP01 not connected to
AC motor drive

Check if AC motor drive is powered, and if the
power supply is normal.
Make sure CMC-EIP01 is connected to AC motor
drive.

CMC-EIP01 not connected to
network

Make sure the network cable is correctly connected
to network.

Poor contact to RJ-45
connector

Make sure RJ-45 connector is connected to
Ethernet port.

AC motor drive not powered
POWER LED off

LINK LED off

8-34

Chapter 8 Optional Cards C2000 Series

Abnormality

No communication
card found

Fail to open
CMC-EIP01 setup
page

Able to open
CMC-EIP01 setup
page but fail to
utilize webpage
monitoring

Fail to send e-mail

Cause

How to correct it?

CMC-EIP01 not connected to
network

Make sure CMC-EIP01 is connected to network.

PC and CMC-EIP01 in
different networks and blocked
by network firewall.

Search by IP or set up relevant settings by AC
motor drive keypad.

CMC-EIP01 not connected to
network
Incorrect communication
setting in DCISoft

Make sure CMC-EIP01 is connected to the
network.
Make sure the communication setting in DCISoft is
set to Ethernet.

PC and CMC-EIP01 in
different networks and blocked
by network firewall.

Conduct the setup by AC motor drive keypad.

Incorrect network setting in
CMC-EIP01

Check if the network setting for CMC-EIP01 is
correct. For the Intranet setting in your company,
please consult your IT staff. For the Internet setting
in your home, please refer to the network setting
instruction provided by your ISP.
Check if the network setting for CMC-EIP01 is
correct.

Incorrect mail server setting

Please confirm the IP address for SMTP-Server.

Incorrect network setting in
CMC-EIP01

8-35

Chapter 8 Optional Cards C2000 Series

8-15 EMC-COP01
Built-in EMC-COP01 card are available in VFDXXXC23E/VFDXXXC43E series.
RJ-45 Pin definition

Pin
1
2
3
7

RS485 socket



Pin name
CAN_H

Definition
CAN_H bus line (dominant
high)
CAN_L
CAN_L bus line (dominant low)
CAN_GND Ground/0V/VCAN_GND Ground/0V/V-

Specifications
Interface

RJ-45

Number of ports

1 Port

Transmission method

CAN

Transmission cable

CAN standard cable

Transmission speed

1M 500k 250k 125k 100k 50k

Communication protocol


CANopen

CANopen Communication Cable
Model: TAP-CB03, TAP-CB04



Title

Part No.

1
2

TAP-CB03
TAP-CB04

L
mm
500  10
1000 10

inch
19  0.4
39  0.4

CANopen Dimension
Model: TAP-CN03

NOTE

For more information on CANopen, please refer to Chapter 15 CANopen Overview or CANopen
user manual can also be downloaded on Delta website: http://www.delta.com.tw/industrialautomation/.

8-36

Chapter 9 Specifications C2000 Series

Chapter 9 Specification

Input Rating

007
0.4
0.75

015
0.75
1.5

022
1.5
2.2

037
2.2
3.7

055
3.7
5.5

B
075
5.5
7.5

110
7.5
11

150
11
15

C
185
15
18.5

220
18.5
22

Heavy
duty

1.9

2.8

4.0

6.4

9.6

12

19

25

28

34

4.8

7.1

10

16

24

31
2~6kHz

47

62

71

86

Normal
duty

Frame Size
Model VFD-_ _ _C_ _
Applicable Motor Output(kW)
Applicable Motor Output(HP)
Rated Output Capacity
(kVA)
Rated Output Current (A)
Carrier Frequency (kHz)
Rate Output Capacity
(kVA)
Rated Output Current (A)
Carrier Frequency (kHz)
Input Current (A) Heavy Duty
Input Current (A)
Normal Duty
Rated Voltage/Frequency
Operating Voltage Range
Frequency Tolerance
AC Drive Weight
Cooling method
Braking Chopper
DC reactor
EMC Filter
EMC-COP01

2.0

3.2

4.4

6.8

10

13

20

26

30

36

5

8

11

25

33

49

65

90

6.1

11

15

26

34

50

68

75
2~10kHz
78

95

6.4

12

16

28

36

52

72

83

99

Heavy
duty

Frame Size
Model VFD-_ _ _C_ _
Applicable Motor Output(kW)
Applicable Motor Output(HP)
Rated Output Capacity
(kVA)
Rated Output Current (A)
Carrier Frequency (kHz)
Rate Output Capacity
(kVA)
Rated Output Current (A)
Carrier Frequency (kHz)
Input Current (A) Heavy Duty
Input Current (A)
Normal Duty
Rated Voltage/Frequency
Operating Voltage Range
Frequency Tolerance

Normal
duty

Output Rating

Input Rating

Output Rating

9-1 230V Series

AC Drive Weight
Cooling method
Braking Chopper
DC reactor
EMI Filter
EMC-COP01

A

2.6± 0.3Kg
Natural cooling

370
30
37

20

3-phase AC 200V~240V (-15% ~ +10%), 50/60Hz
170~265Vac
47~63Hz
5.4± 1Kg
Fan cooling
Frame A to C (built-in); Frame D and above (optional)
Frame A to C (optional); Frame D and above (built-in)
Frame A to C (optional); Frame D and above (optional)
VFDXXC23A (optional); VFDXXXC23E (built-in)

D
300
22
30

17
2~15kHz
18.5

450
37
45

E
550
45
55

750
55
75

F
900
75
90

45

55

68

81

96

131

114

139

171

204
2~6kHz

242

329

48

58

72

86

102

138

120
146
2~10kHz
118
136

180

346

162

215
255
2~9 kHz
196
233

315

124

171

206

331

143

245

3-phase AC 200V~240V (-15% ~ +10%), 50/60Hz
170~265Vac
47~63Hz
86.5±1
38.5± 1.5Kg
64.8± 1.5Kg
.5Kg
Fan Cooling
Frame A to C (built-in); Frame D and above (optional)
Frame A to C (optional); Frame D and above (built-in)
Frame A to C (optional); Frame D and above (optional)
VFDXXC23A (optional); VFDXXXC23E (built-in)

9-1

9.8± 1.5Kg

Chapter 9 Specifications C2000 Series

9-2 460V Series
Frame Size

A

B

C

D0

Model VFD-_ _ _ C_ _

007

015

022

037

040

055

075

110

150

185

220

300

370

450

Applicable Motor Output(kW)

0.75

1.5

2.2

3.7

4.0

5.5

7.5

11

15

18.5

22

30

37

45

7.5

10

15

20

25

30

40

50

60

9.6

14

18

24

29

34

45

55

69

5.7

8.1

9.5

11

17

23

30

36

43

57

69

86

Heavy duty

5
7.6

Normal duty

5
6.5

4.8

7.2

8.4

10

14

19

25

30

36

48

58

73

6.0

9.0

10.5

12

18

24

32

38

45

60

73

91

EMI Filter
EMC-COP01
Frame Size

Input Rating

Normal duty

Heavy duty

Model VFD-_ _ _ C_ _
Applicable Motor Output(kW)
Applicable Motor Output(HP)
Rated Output Capacity
(kVA)
Rated Output Current
(A)
Carrier Frequency
(kHz)
Rate Output Capacity
(kVA)
Rated Output Current
(A)
Carrier Frequency
(kHz)
Input Current (A) Heavy Duty
Input Current (A)
Normal Duty
Rated Voltage/Frequency
Operating Voltage Range
Frequency Tolerance
AC Drive Weight
Cooling method
Braking Chopper
DC reactor

Output Rating

3
4.5

Input Rating

Output Rating

Applicable Motor Output(HP)
1
2
Rated Output Capacity
2.3
3.0
(kVA)
Rated Output Current
2.9
3.8
(A)
Carrier Frequency
(kHz)
Rate Output Capacity
2.4
3.2
(kVA)
Rated Output Current
3.0
4.0
(A)
Carrier Frequency
(kHz)
Input Current (A) Heavy
4.1
5.6
Duty
Input Current (A)
4.3
5.9
Normal Duty
Rated Voltage/Frequency
Operating Voltage Range
Frequency Tolerance
AC Drive Weight
Natural cooling
Cooling method
Braking Chopper
DC reactor

EMI Filter
EMC-COP01

2~6kHz (2kHz)

2~15kHz (8kHz)

2~10kHz (6kHz)

8.3

13

14.5

16

19

25

33

38

45

60

70

96

8.7

14

15.5

17

20

26

35

40

47

63

74

101

3-phase AC 380V~480V ( -15%~+10%), 50/60Hz
323~528Vac
47~63Hz
2.6± 0.3Kg
5.4± 1Kg
9.8± 1.5Kg
Fan cooling
Frame A to C (built-in); Frame D and above (optional)
Frame A to C (optional); Frame D and above (built-in)
VFDXXXC43A Frame A to C: No EMI Filter; VFDXXXC43E: Built-in EMI Filter
VFDXXXC43A/43E Frame D and above: EMI Filter is optional
VFDXXC43A (optional); VFDXXXC43E (built-in)

D

E

F

G

27± 1 Kg

H

550
55
75

750
75
100

900
90
125

1100
110
150

1320
132
175

1600
160
215

1850
185
250

2200
220
300

2800
280
375

3150
315
420

3550
355
475

4500
450
600

84

114

136

167

197

235

280

348

417

466

517

677

105

143

171

209

247

295

352

437

523

585

649

816

2~6kHz (2kHz)
88

120

143

175

207

247

295

367

438

491

544

720

110

150

180

220

260

310

370

460

550

616

683

866

108

149

159

197

228

285

361

380

469

527

594

816

114

157

167

207

240

300

380

400

494

555

625

866

2~10kHz (6kHz)

2~9kHz (4kHz)

3-phase AC 380V~~480V (-15% +10%), 50/60Hz
323~528Vac
47~63Hz
38.5± 1.5Kg
64.8± 1.5Kg
86.5± 1.5Kg
134± 4Kg
228Kg
Fan cooling
Frame A to C (built-in); Frame D and above (optional)
Frame A to C (optional); Frame D and above (built-in)
VFDXXXC43A Frame A to C: No EMI Filter; VFDXXXC43E: Built-in EMI Filter
VFDXXXC43A/43E Frame D and above: EMI Filter is optional
VFDXXC43A (optional); VFDXXXC43E (built-in)

NOTE






The value of the carrier frequency is a factory setting. To increase the carrier frequency, the current needs to be decreased. See derating
curve diagram of Pr06-55 for more information.
When the control mode is FOC senrorless, TQC+PG, TQC sensorless, PM+PG and PM sensorless, the current needs to be decreased. For
more information see Pr06-55.
When a load is a shock or impact load, use a higher level model.
For FRAME A, B and C, Model VFDXXXC43A the enclosure type is IP20/NEMA1/UL TYPE1.
For FRAME D and above, if the last character of the model is A then the enclosure type is IP20 but the wiring terminal is IP00; if the last
character of the model is E, the enclosure type is IP20/NEMA1/UL TYPE1.

9-2

Chapter 9 Specifications C2000 Series

General Specifications
Control Method

1: V/F, 2: SVC, 3: VF+PG, 4: FOC+PG, 5: TQC+PG,
Reach up to 150% or above at 0.5Hz.
Under FOC+PG mode, starting torque can reach 150% at 0Hz.
V/F Curve
4 point adjustable V/F curve and square curve
Speed Response Ability
5Hz (vector control can reach up to 40Hz)
Torque Limit
Max. 200% torque current
Torque Accuracy
5%
Max. Output Frequency(Hz) normal duty: 0.01~600.00Hz; Heavy duty: 0.00 ~ 300.00 Hz
Frequency Output Accuracy Digital command:0.01%, -10℃~+40℃, Analog command: 0.1%, 2510℃
Output Frequency
Digital command:0.01Hz, Analog command: 0.03 X max. output frequency/60 Hz (11 bit)
Resolution
Normal duty: rated output current is 120% for 60 seconds
Overload Tolerance
Heavy duty: rated output current is 150% for 60 seconds
Frequency Setting Signal
+10V~-10, 0~+10V, 4~20mA, 0~20mA, Pulse input
Accel./decel. Time
0.00~600.00/0.0~6000.0 seconds
Torque control, Droop control, Speed/torque control switching, Feed forward control, Zero-servo control,
Momentary power loss ride thru, Speed search, Over-torque detection, Torque limit, 17-step speed (max),
Accel/decel time switch, S-curve accel/decel, 3-wire sequence, Auto-Tuning (rotational, stationary), Dwell,
Main control function
Cooling fan on/off switch, Slip compensation, Torque compensation, JOG frequency, Frequency
upper/lower limit settings, DC injection braking at start/stop, High slip braking, PID control (with sleep
function),Energy saving control, MODOBUS communication (RS-485 RJ45, max. 115.2 kbps), Fault
restart, Parameter copy
Frame A,B is on/off control
Fan Control
Frame C and above is PWM control
Motor Protection
Electronic thermal relay protection
For drive model 230V and 440V
Over-current protection for 220% rated current
Over-current Protection
current clamp『Normal duty: 170~175%』;『Heavy duty: 180~185%』
230: drive will stop when DC-BUS voltage exceeds 410V
Over-voltage Protection
460: drive will stop when DC-BUS voltage exceeds 820V
Over-temperature
Built-in temperature sensor
Protection
Stall Prevention
Stall prevention during acceleration, deceleration and running independently
Restart After Instantaneous
Parameter setting up to 20 seconds
Power Failure
Grounding Leakage Current
Leakage current is higher than 50% of rated current of the AC motor drive
Protection

Protection Characteristics

Control Characteristics

Starting Torque

Certifications
,

,

GB/T12668-2,

9-3

(certification in progress)

Chapter 9 Specifications C2000 Series

9-3 Environment for Operation, Storage and Transportation
DO NOT expose the AC motor drive in the bad environment, such as dust, direct sunlight, corrosive/inflammable gasses, humidity, liquid and
2
vibration environment. The salt in the air must be less than 0.01mg/cm every year.
Installation
IEC60364-1/IEC60664-1 Pollution degree 2, Indoor use only
location
o
o
Storage
-25 C ~ +70 C
Surrounding
o
o
Transportation
-25 C ~ +70 C
Temperature
Non-condensation, non-frozen
Operation
Max. 95%
Storage/
Max. 95%
Rated Humidity
Transportation
No condense water
Operation/
86 to 106 kPa
Storage
Environment
Air Pressure
Transportation
70 to 106 kPa
IEC721-3-3
Operation
Class 3C2; Class 3S2
Storage
Class 2C2; Class 2S2
Pollution Level
Transportation
Class 1C2; Class 1S2
No concentrate
If AC motor drive is installed at altitude 0~1000m, follow normal operation restriction. If
it
is install at altitude 1000~2000m, decrease 2% of rated current or lower 0.5℃ of
Operation
Altitude
temeperature for every 100m increase in altitude. Maximum altitude for Corner
Grounded is 2000m.
Storage
ISTA procedure 1A(according to weight) IEC60068-2-31
Package Drop
Transportation
1.0mm, peak to peak value range from 2Hz to 13.2 Hz; 0.7G~1.0G range from 13.2Hz to 55Hz; 1.0G range from 55Hz to
Vibration
512 Hz. Comply with IEC 60068-2-6
Impact
Operation
Position

IEC/EN 60068-2-27
Max. allowed offset angle 10 (under normal installation
position)
o

9-4

10

10

Chapter 9 Specifications C2000 Series

9-4 Specification for Operation Temperature and Protection Level
Model

Frame

Top cover

Conduit Box

Frame A~C
230V: 0.75~22kW
460V: 0.75~30kW

Top cover
Removed
Standard with
top cover

Standard conduit
plate

Protection Level

Operation
Temperature

IP20/UL Open Type

-10~50℃

IP20/UL Type1/NEMA1

-10~40℃

IP00/IP20/UL Open Type
O n l y th e ci rcl e d a re a
i s IP0 0 , o th e r a re IP2 0

VFDxxxCxxA
Frame D~H
230V: >22kW
460V: >30kW

Frame A~C
460V: 0.75~30kW
VFDxxxCxxE
Frame D~H
230V: >22kW
460V: >30kW

N/A

Top cover
Removed
Standard with
top cover
N/A

-10~50℃

No conduit box

Standard conduit
plate
Standard conduit
box

9-5

IP20/UL Open Type

-10~50℃

IP20/UL Type1/NEMA1

-10~40℃

IP20/UL Type1/NEMA1

-10~40℃

Chapter 9 Specifications C2000 Series

9-5 Derating of ambient temperature and altitude
C Type Derating for Altitude
Rating (%) at Stardard Ambient Temperature*

Ta at Rating= 100%

100

50 40

90

45 35

80

40 30

60
50
40
0

500

1000

1500
2000
Altitude (m)

2500

3000

UL Open Type / IP20 Side by Side
UL Type I / IP20

UL Open Type / IP20

70

* Stardard Ambient Temperature= 50 degC for UL Open Type / IP20
Stardard Ambient Temperature= 40 degC for UL Type I /IP 20 & UL Open Type / IP20 Side by Side

Protection Level

UL Type I / IP20

UL Open Type / IP20

High Altitude

Operating Environment
When the AC motor drive is operating at the rated current and the ambient temperature
has to be between 10℃ ~ +40℃. When the temperature is over 40℃, for every
increase by 1℃, decrease 2% of the rated current. The maximum allowable
temperature is 60℃.
When the AC motor drive is operating at the rated current and the ambient temperature
has to be between -10℃ ~ +50℃. When the temperature is over 50℃, for every
increase by 1℃, decrease 2% of the rated current. The maximum allowable
temperature is 60℃.
If AC motor drive is installed at altitude 0~1000m, follow normal operation restriction. If
it is install at altitude 1000~2000m, decrease 2% of rated current or lower 0.5℃ of
temperature for every 100m increase in altitude. Maximum altitude for Corner
Grounded is 2000m. Contact Delta for more information, if you need to use this motor
drive at an altitude of 2000m or higher.

9-6

Chapter 10 Digital KeypadC2000

Chapter 10 Digital Keypad
10-1 Descriptions of Digital Keypad
10-2 Function of Digital Keypad KPC-CC01
10-3 TPEditor Installation Instruction
10-4 Fault Code Description of Digital Keypad KPC-CC01

10-1

Chapter 10 Digital KeypadC2000 Series

10-1 Descriptions of Digital Keypad
KPC-CC01

KPC-CE01(Option)
Communication Interface
RJ-45 (socket)、RS-485 interface;
Installation Method
1.
Embedded type and can be put flat on the
surface of the control box. The front cover is
water proof.
2.
Buy a MKC-KPPK model to do wall
mounting or embedded mounting. Its
protection level is IP66.
3.
The maximum RJ45 extension lead is 5 m
(16ft)
4.
This keypad can only be used on Delta’s
motor drive C2000, CH2000 and CP2000.

Descriptions of Keypad Functions
Descriptions

Key

Start Operation Key
1.
It is only valid when the source of operation command is from the keypad.
2.
It can operate the AC motor drive by the function setting and the RUN LED will be ON.
3.
It can be pressed again and again at stop process.
4.
When enabling “HAND” mode, it is only valid when the source of operation command is
from the keypad.
Stop Command Key. This key has the highest processing priority in any situation.
1.
When it receives STOP command, no matter the AC motor drive is in operation or stop
status, the AC motor drive needs to execute “STOP” command.
2.
The RESET key can be used to reset the drive after the fault occurs. For those faults that
can’t be reset by the RESET key, see the fault records after pressing MENU key for
details.
Operation Direction Key
1.
This key is only control the operation direction NOT for activate the drive. FWD: forward,
REV: reverse.
2.
Refer to the LED descriptions for more details.
ENTER Key
Press ENTER and go to the next level. If it is the last level then press ENTER to execute the command.

ESC Key
ESC key function is to leave current menu and return to the last menu. It is also functioned as a
return key in the sub-menu.
Press menu to return to main menu.
Menu content:
KPC-CE01 does not support function 5 ~13.
1. Parameter setup
7. Quick start
13. PC Link
2. Copy Parameter
8. Display Setup
3. Keypad Locked
9. Time Setup
4. PLC Function
10. Language Setup
5. Copy PLC
11. Startup Menu
6. Fault Record
12. Main Page
Direction: Left/Right/Up/Down
1.
In the numeric value setting mode, it is used to move the cursor and change the numeric
value.
2.
In the menu/text selection mode, it is used for item selection.

10-2

Chapter 10 Digital KeypadC2000
Function Key
1.
The functions keys have factory settings and can be defined by users. The factory settings
of F1 and F4 work with the function list below. For example, F1 is JOG function, F4 is a
speed setting key for adding/deleting user defined parameters.
2.
Other functions must be defined by TPEditor first. TPEditor software V1.30.6 is available
for download at:
http://www.delta.com.tw/ch/product/em/download/download_main.asp?act=3&pid=1&cid=
1&tpid=3
3.
Installation Instruction for TPEditor is on page 10-15 of this chapter.
HAND ON Key
1.
This key is executed by the parameter settings of the source of Hand frequency and hand
operation. The factory settings of both source of Hand frequency and hand operation are
the digital keypad.
2.
Press HAND ON key at stop status, the setting will switch to hand frequency source and
hand operation source. Press HAND ON key at operation status, it stops the AC motor
drive first (display AHSP warning), and switch to hand frequency source and hand
operation source.
3.
Successful mode switching for KPC-CE01, “H/A” LED will be on; for KPC-CC01, it will
display HAND mode/ AUTO mode on the screen.
1.
This key is executed by the parameter settings of the source of AUTO frequency and
AUTO operation. The factory setting is the external terminal (source of operation is
4-20mA).
2.
Press Auto key at stop status, the setting will switch to hand frequency source and hand
operation source. Press Auto key at operation status, it stops the AC motor drive first
(display AHSP warning), and switch to auto frequency source and auto operation source.
3.
Successful mode switching for KPC-CE01, “H/A” LED will be off; for KPC-CC01, it will
display HAND mode/ AUTO mode on the screen

Descriptions of LED Functions
LED

Descriptions
Steady ON: operation indicator of the AC motor drive, including DC brake, zero speed,
standby, restart after fault and speed search.
Blinking: drive is decelerating to stop or in the status of base block.
Steady OFF: drive doesn’t execute the operation command
Steady ON: stop indicator of the AC motor drive.
Blinking: drive is in the standby status.
Steady OFF: drive doesn’t execute “STOP” command.
Operation Direction LED
1. Green light is on, the drive is running forward.
2. Red light is on, the drive is running backward.
3. Twinkling light: the drive is changing direction.
(Only KPC-CE01 support this function)
Setting can be done during operation.
HAND LED: When HAND LED is on (HAND mode); when HAND LED is off (AUTO mode).
(Only KPC-CE01Support this function )
Setting can be done during operation.
AUTO LED: when AUTO LED is on (AUTO mode); when AUTO LED is off (HAND mode).

10-3

Chapter 10 Digital KeypadC2000 Series
RUN LED:
LED
status
OFF
CANopen at initial

Condition/State

No LED
Blinking CANopen at pre-operation

CANopen ~”RUN”
Single
flash

ON

CANopen at stopped

CANopen at operation status
No LED

ERR LED:
LED
status
OFF
Single One message fail
flash

CANopen ~”ERR”

Double
flash

Triple
flash

Condition/ State
No Error

Guarding fail or heartbeat fail

SYNC fail

ON

Bus off

10-4

Chapter 10 Digital KeypadC2000

10-2 Function of Digital Keypad KPC-CC01

1.
2.

NOTE
Startup page can only display pictures, no flash.
When Power ON, it will display startup page then the main page. The main page displays Delta’s default setting F/H/A/U,
the display order can be set by Pr.00.03 (Startup display). When the selected item is U page, use left key and right key to
switch between the items, the display order of U page is set by Pr.00.04 (User display).

10-5

Chapter 10 Digital KeypadC2000 Series

Display Icon

Display item

1.

Parameter Setup
For example: Setup source of master frequency command.
Once in the Group 00 Motor Drive Parameter,
Use Up/Down key to select parameter 20:
Auto Frequency Command.
When this parameter is selected, press
ENTER key to go to this parameter’s setting
menu.
Use Up/Down key to choose a setting.
For example: Choose “2 Analogue Input, then
press the ENTER key.
After pressing the ENTER key, an END will be
displayed which means that the parameter
setting is done.

2.

Copy Parameter
4 duplicates are provided
The steps are shown in the example below.
Example: Saved in the motor drive.
1 Go to Copy Parameter
2 Select the parameter group which needs to

Press ENTER key to go to 001~004:

be copied and press ENTER key.

content storage
1 Select 1: Save in the motor drive.
2. Press ENTER key to go to “Save in the
motor drive” screen.

10-6

Chapter 10 Digital KeypadC2000

Begin to copy parameters until it is done.

Once copying parameters is done, keypad
will automatically be back to this screen.
Example: Saved in the keypad.
1. Once copying parameters is done, keypad
will automatically be back to this screen.
2. Select the parameter group which needs to
be copied and press ENTER key.
Press ENTER key to go to “Save in the motor
drive” screen.

Use Up/Down key to select a symbol.
Use Left/Right key to move the cursor to
select a file name.
String & Symbol Table:
！＂＃＄％＆＇（）＊＋，－．／０１２３４５６７８９：；＜＝
＞？＠ＡＢＣＤＥＦＧＨＩＪＫＬＭＮＯＰＱＲＳＴＵＶＷＸＹＺ
［＼］＾＿｀ａｂｃｄｆｇｈｉｊｋｌｍｎｏｐｑｒｓｔｕｖｗｘ
ｙｚ｛｜｝～
Once the file name is confirmed, press
ENTER key.

To begin copying parameters until it is done.

When copying parameters is completed,
keypad will automatically be back to this
screen.

Press Right key to see the date of copying
parameters.

Press Right key to see the time of copying
parameters.

10-7

Chapter 10 Digital KeypadC2000 Series

3.

Keypad locked
Keypad Locked
This function is used to lock the keypad. The main page would not display
“keypad locked” when the keypad is locked, however it will display the
message”please press ESC and then ENTER to unlock the keypad” when any
key is pressed.
When the keypad is locked, the main screen doesn’t
display any status to show that.

Press any key on the keypad; a screen as shown in
image on the left will be displayed.

If ESC key is not pressed, the keypad will
automatically be back to this screen.
The keypad is still locked at this moment. By
pressing any key, a screen as shown in the image on
the left will still be displayed.
Press ESC for 3 seconds to unlock the keypad and
the keypad will be back to this screen. Then each key
on the keypad is functional.
Turn off the power and turn on the power again will not lock keypad.

4.

PLC Function
When activate and stop PLC function, the PLC status will be displayed on
main page of Delta default setting.
Optipn 2: Enable PLC function
Press Up/Down key to select a
PLC’s function.
Then press ENTER.

Factory setting on the main screen displays
PLC/RUN status bar.

Option 3: Disable PLC function

Factory setting on the main screen displays
PLC/STOP status bar
If the PLC program is not available in the control
board, PLFF warning will be displayed when
choosing option 2 or 3.
In this case, select option 1 : No Function to clear
PLFF warning.
The PLC function of KPC-CE01 can only displays:
1.
PLC0
2.
PLC1
3.
PLC2

10-8

Chapter 10 Digital KeypadC2000
5.

Copy PLC
4 duplicates are provided
The steps are shown in the example below.
Example: Saved in the motor drive.
1 Go to Copy PLC
2 Select a parameter group to copy then press
ENTER
1 Select 1: Save in the motor drive.
2. Press ENTER key to go to “Save in the motor
drive” screen.

Begin to copy PLC until it is done.

Once copying PLC is done, keypad will automatically
be back to this screen.
NOTE

If “Option 1: Save in the motor drive” is selected,
verify if the PLC program is built-in to KPC-CC01
keypad. If PLC program is not available in the
keypad while “Option 1: Save in the motor drive” is
selected, an “ERR8 Warning: Type not matching” will
be display on the screen.
Unplug and plug back the keypad while copying
the PLC program will have a CPLt warning.

Example: Saved in the keypad.
Once copying PLC is done, keypad will
automatically be back to this screen.
2. Select the parameter group which needs to be
copied and press ENTER key.

1.

Press ENTER key to go to “Save in the motor
drive” screen.

If WPLSoft editor is installed and password is
set, enter the password to save the file onto digital
display.
Use Up/Down key to select a symbol.
Use Left/Right key to move the cursor to select a
file name.
String & Symbol Table:
！＂＃＄％＆＇（）＊＋，－．／０１２３４５６７８９：；＜＝＞？＠Ａ
ＢＣＤＥＦＧＨＩＪＫＬＭＮＯＰＱＲＳＴＵＶＷＸＹＺ［＼］＾＿｀ａｂ
ｃｄｆｇｈｉｊｋｌｍｎｏｐｑｒｓｔｕｖｗｘｙｚ｛｜｝～

10-9

Chapter 10 Digital KeypadC2000 Series

Once the file name is confirmed, press ENTER key.

To begin copying parameters until it is done.

When copying parameters is completed, keypad will
automatically be back to this screen.

Press Right key to see the date of copying
parameters.

Press Right key to see the time of copying
parameters.

6.

Fault record
Able to store 6 error code (Keypad V1.02 and previous versions)
Able to store 20 error code(Keypad V1.0e3 and previous version)
The most recent error record is shown as the first record. Select an error
record to see its detail such as date, tme, frequency, current, voltage, DCBUs
voltage)

Press

Press Up/Down key to select an error record.
After selecting an error code, press ENTER to see
that error record’s detail

ENTER to select.

KPC-CE01 does not support
this function.

Press Up/Down key to see an error record’s detail
such as date, time, frequency, current, voltage,
DCBus voltage.

Press Up/Down key to select an error record.
After selecting an error code, press ENTER to see
that error record’s detail

Press Up/Down key to see an error record’s detail
such as date, time, frequency, current, voltage,
DCBus voltage.

NOTE

Fault actions of AC motor drive are record and save to KPC-CC01. When
KPC-CC01 is removed and apply to another AC motor drive, the previous
fault records will not be deleted. The new fault records of the present AC
motor drive will accumulate to KPC-CC01.

10-10

Chapter 10 Digital KeypadC2000
7.

Quick Start
Description:
1.

Press

ENTER to select.

Quick Start:
1. V/F Mode
2. VFPG Mode
3. SVC Mode
4. FOCPG Mode
5. TQCPG Mode
6. My Mode

2.

VF Mode
Items
1. Parameter Protection Password Input
(P00-07)
2. Parameter Protection Password Setting
(P00-08)
3. Control Mode (P00-10)
4. Control of Speed Mode (P00-11)
01:Password Decoder
5. Load Selection (P00-16)
6. Source of the Master Frequency
Command (AUTO) (P00-20)
7. Source of the Operation Command
(AUTO) (P00-21)
8. Stop Method (P00-22)
9. Digital Keypad STOP function (P00-32)
10. Max. Operation Frequency (P01-00)
11. Base Frequency of Motor 1 (P01-01)
12. Max. Output Voltage Setting of Motor 1
(P01-02)
13. Min. Output Frequency of Motor 1
(P01-07)
14. Min. Output Voltage of Motor 1 (P01-08)
15. Output Frequency Upper Limit (P01-10)
16. Output Frequency Lower Limit (P01-11)
17. Accel. Time 1 (P01-12)
18. Decel Time 1 (P01-13)
19. Over-voltage Stall Prevention (P06-01)
20. Software Brake Level (P07-00)
21. Filter Time of Torque Command
(P07-24)
22. Filter Time of Slip Compensation
(P07-25)
23. Slip Compensation Gain (P07-27)
VFPG Mode
Items
1. Parameter Protection Password Input
(P00-07)
2. Parameter Protection Password
Setting (P00-08)
3. Control Mode (P00-10)
4. Control of Speed Mode (P00-11)
01: Password Decoder
5. Load Selection (P00-16)
6. Source of the Master Frequency
Command (AUTO) (P00-20)
7. Source of the Operation Command
(AUTO) (P00-21)
8. Stop Method (P00-22)
9. Digital Keypad STOP function (P00-32)
10. Max. Operation Frequency (P01-00)
11. Base Frequency of Motor 1 (P01-01)
12. Max. Output Voltage Setting of Motor 1
(P01-02)
13. Min. Output Frequency of Motor 1
(P01-07)
14. Min. Output Voltage of Motor 1
(P01-08)
15. Output Frequency Upper Limit
(P01-10)
16. Output Frequency Lower Limit
(P01-11)
17. Accel. Time 1 (P01-12)

10-11

Chapter 10 Digital KeypadC2000 Series
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
3.

Decel Time 1 (P01-13)
Over-voltage Stall Prevention
(P06-01)
Software Brake Level (P07-00)
Filter Time of Torque Command
(P07-24)
Filter Time of Slip Compensation
(P07-25)
Slip Compensation Gain (P07-27)
Encoder Type Selection (P10-00)
Encoder Pulse (P10-01)
Encoder Input Type Setting (P10-02)
ASR Control ( P) 1 (P11-06)
ASR Control (I) 1 (P11-07)
ASR Control ( P) 2 (P11-08)
ASR Control (I) 2 (P11-09)
P Gain of Zero Speed (P11-10)
I Gain of Zero Speed (P11-11)

SVC Mode
Items
1.
Parameter Protection Password Input
(P00-07)
2.
Parameter Protection Password
Setting (P00-08)
3.
Control Mode (P00-10)
4.
Control of Speed Mode (P00-11)
01: Password Decoder
5.
Load Selection (P00-16)
6.
Carrier Frequency (P00-17)
7.
Source of the Master Frequency
Command (AUTO) (P00-20)
8.
Source of the Operation Command
(AUTO) (P00-21)
9.
Stop Method (P00-22)
10. Digital Keypad STOP function
(P00-32)
11. Max. Operation Frequency (P01-00)
12. Base Frequency of Motor 1 (P01-01)
13. Max. Output Voltage Setting of Motor
1 (P01-02)
14. Min. Output Frequency of Motor 1
(P01-07)
15. Min. Output Voltage of Motor 1
(P01-08)
16. Output Frequency Upper Limit
(P01-10)
17. Output Frequency Lower Limit
(P01-11)
18. Accel. Time 1 (P01-12)
19. Decel Time 1 (P01-13)
20. Full-load Current of Induction Motor 1
(P05-01)
21. Rated Power of Induction Motor 1
(P05-02)
22. Rated Speed of Induction Motor 1
(P05-03)
23. Pole Number of Induction Motor 1
(P05-04)
24. No-load Current of Induction Motor 1
(P05-05)
25. Over-voltage Stall Prevention
(P06-01)
26. Over-current Stall Prevention during
Acceleration (P06-03)
27. Derating Protection (P06-55)
28. Software Brake Level (P07-00)

10-12

Chapter 10 Digital KeypadC2000
29.
30.
31.
32.
4.

Emergency Stop (EF) & Force to Stop
Selection (P07-20)
Filter Time of Torque Command
(P07-24)
Filter Time of Slip Compensation
(P07-25)
Slip Compensation Gain (P07-27)

FOCPG Mode
Items
1. Parameter Protection Password Input
(P00-07)
2. Parameter Protection Password Setting
(P00-08)
3. Control Mode (P00-10)
4. Control of Speed Mode (P00-11)
01: Password Decoder
5. Source of the Master Frequency
Command (AUTO) (P00-20)
6. Source of the Operation Command
(AUTO) (P00-21)
7. Stop Method (P00-22)
8. Max. Operation Frequency (P01-00)
9. Base Frequency of Motor 1 (P01-01)
10. Max. Output Voltage Setting of Motor 1
(P01-02)
11. Output Frequency Upper Limit (P01-10)
12. Output Frequency Lower Limit (P01-11)
13. Accel. Time 1 (P01-12)
14. Decel Time 1 (P01-13)
15. Full-load Current of Induction Motor 1
(P05-01)
16. Rated Power of Induction Motor 1
(P05-02)
17. Rated Speed of Induction Motor 1
(P05-03)
18. Pole Number of Induction Motor 1
(P05-04)
19. No-load Current of Induction Motor 1
(P05-05)
20. Over-voltage Stall Prevention (P06-01)
21. Over-current Stall Prevention during
Acceleration (P06-03)
22. Derating Protection (P06-55)
23. Software Brake Level (P07-00)
24. Emergency Stop (EF) & Force to Stop
Selection (P07-20)
25. Encoder Type Selection (P10-00)
26. Encoder Pulse (P10-01)
27. Encoder Input Type Setting (P10-02)
28. System Control (P11-00)
29. Per Unit of System Inertia (P11-01)
30. ASR1 Low-speed Bandwidth (P11-03)
31. ASR2 High-speed Bandwidth (P11-04)
32. Zero-speed Bandwidth (P11-05)

10-13

Chapter 10 Digital KeypadC2000 Series
5.

TQCPG Mode
Items
1. Password Input (Decode) (P00-07)
2. Password Setting (P00-08)
3. Control Mode (P00-10)
4. Control of Speed Mode (P00-11)
5. Source of the Master Frequency
Command (P00-20)
01: Password Decoder
6. Source of the Operation Command
(P00-21)
7. Max. Operation Frequency (P01-00)
8. Base Frequency of Motor 1 (P01-01)
9. Max. Output Voltage Setting of Motor 1
(P01-02)
10. Full-load Current of Induction Motor 1
(P05-01)
11. Rated Power of Induction Motor 1
(P05-02)
12. Rated Speed of Induction Motor 1
(P05-03)
13. Pole Number of Induction Motor 1
(P05-04)
14. No-load Current of Induction Motor 1
(P05-05)
15. Over-voltage Stall Prevention (P06-01)
16. Software Brake Level (P07-00)
17. Encoder Type Selection (P10-00)
18. Encoder Pulse (P10-01)
19. Encoder Input Type Setting (P10-02)
20. System Control (P11-00)
21. Per Unit of System Inertia (P11-01)
22. ASR1 Low-speed Bandwidth (P11-03)
23. ASR2 High-speed Bandwidth (P11-04)
24. Zero-speed Bandwidth (P11-05)
25. Max. Torque Command (P11-27)
26. Source of Torque Offset (P11-28)
27. Torque Offset Setting (P11-29)
28. Source of Torque Command (P11-33)
29. Torque Command (P11-34)
30. Speed Limit Selection (P11-36)
31. Forward Speed Limit (torque mode)
(P11-37)
32. Reverse Speed Limit (torque mode)
(P11-38)

10-14

Chapter 10 Digital KeypadC2000
6.

My Mode
Items

Click F4 in parameter
setting page, the
parameter will save to

It can save 01~32 sets of parameters (Pr).
Setup process
1. Go to Parameter Setup function.
Press ENTER to go to the parameter
which you need to use. There is an
ADD on the bottom right-hand corner of
the screen. Press F4 on the key pad
to add this parameter to My Mode

My Mode. To delete or
correct the parameter,
enter this parameter and
click the “DEL” on the
bottom right corner.

2. The parameter (Pr) will be displayed in
My mode if it is properly saved.
To correct or to delete this Pr. clicks
DEL.

3. To delete a parameter, go to My Mode
and select a parameter which you need
to delete.
Press ENTER to enter the parameter
setting screen. There is a DEL on the
bottom left-hand corner of the screen.
Press F4 on the keypad to delete this
parameter from My Mode.

4. After pressing ENTER to delete <01
Control Mode>, the <02 Maximum
Operating Frequency > will
automatically replace <01 Control
Mode>.

10-15

Chapter 10 Digital KeypadC2000 Series

8.

Display setup
1. Contrast
Use Up/Down key to adjust the setting
value.

After selecting a setting value. Press
ENTER to see screen’s display after
contrast is adjusted to be +10.

When the setting value is 0 Min, the back
light will be steady on.

Then press ENTER.

After select a setting value Press ENTER to
see screen’s display result after contrast is
adjusted to be -10.
2. Back-light
Press ENTER to go to Back Light Time
Setting screnn.

Use Up/Down key to adjust the setting
value.

When the setting value is 0 Min, the back
light will be steady on.

When the setting value is 10 Min, the
backlight will be off in 10 minutes.

9.

Time setting

Time setup
Use Up/Down key to set up Year

2009/01/01
_ _ : _ _ :_ _
Use Left/Right key to select

Use Up/Down key to set up Month

Year, Month, Day, Hour, Minute
or Second to set up

10-16

Chapter 10 Digital KeypadC2000

Use Up/Down key to set up day

Use Up/Down key to set up hour

Use Up/Down key to set up Minute

Use Up/Down key to set up Second

After setting up, press ENTER to confirm
the setup.

NOTE

When the digital keypad is removed, the time setting will be in standby status
for 7 days. After this period, the time needs to be reset.

10. Language setup
Language setting option is displayed in the language of the user’s choice.
Language setting options:

Use Up/Down key to select
language, than press ENTER.

1. English

5.

2. 繁體中文

6. Espanol

3. 简体中文

7. Portugues

4. Turkce

11. Startup-up
1. Default 1

DELTA LOGO

2. Default 2

DELTA Text

10-17

Chapter 10 Digital KeypadC2000 Series
3. User Defined: optional accessory is require (TPEditor & USB/RS-485
Communication Interface-IFD6530)
Install an editing accessory would allow users to design their own start-up
page.If editor accessory is not installed, “user defined” option will dispay a
blank page.

USB/RS-485 Communication Interface-IFD6530
Please refer to Chapter 07 Optional Acessories for more detail.
TPEditor
Go to Delta’s website to download TPEditor V1.30.6 or later versions.
http://www.delta.com.tw/ch/product/em/download/download_main.asp?act
=3&pid=1&cid=1&tpid=3

12. Main page
1. Default page

F
H
u
Default picture and editable
picture are available upon
selection.

Press

ENTER to select.

60.00Hz
0.00Hz
540.0Vdc

F 600.00Hz >>> H >>> A >>> U (circulate)
2. User Defined: optional accessory is require (TPEditor & USB/RS-485
Communication Interface-IFD6530)
Install an editing accessory would allow users to design their own start-up
page.If editor accessory is not installed, “user defined” option will dispay a
blank page.

USB/RS-485 Communication Interface-IFD6530
Please refer to Chapter 07 Optional Acessories for more detail.
TPEditor
Go to Delta’s website to download TPEditor V1.30.6 or later versions.
http://www.delta.com.tw/ch/product/em/download/download_main.asp?act
=3&pid=1&cid=1&tpid=3

13. PC Link
1.

TPEditor: This function allows users to connect the keypad to a
computer then to download and edit user defined pages.

Click ENTER to go to 

10-18

Chapter 10 Digital KeypadC2000
In TPEditor, choose , then choose “Write to HMI”

Choose  in the  dialogue box.

Start downloading pages to edit KPC-CC01.

Download completed

2.

VFDSoft: this function allows user to link to the VFDSoft Operating
software then to upload data
Copy parameter 1~4 in KPC-CC01
Connect KPC-CCO1 to a computer
Start downloading
KPC-CC01

pages

to

edit

to

Use Up/Down key to select a parameter
group to upload to VFDSoft.
Press ENTER

10-19

Chapter 10 Digital KeypadC2000 Series

Waiting to connect to PC

Open VFDSoft, choose 

In Parameter Manager, choose 

Choose the right communication port and click OK

10-20

Chapter 10 Digital KeypadC2000

Start to upload parameters to VFDSoft

Uploading parameter is completed

Before using the user defined starting screen and user defined main
screen, the starting screen setup and the main screen setup have to be
preset as user defined.
If the user defined page are not downloaded to KPC-CC01, the starting
screen and the main screen will be blank.

10-21

Chapter 10 Digital KeypadC2000 Series

Other display
When fault occur, the menu will display:

Fault

Warning

ocA

CE01
Comm. Error 1

Oc at accel

1. Press ENTER and start RESET. If still no response, please contact local distributor or return to the factory. To
view the fault DC BUS voltage, output current and output voltage, press “MENU”“Fault Record”.
2. Press ENTER again, if the screen returns to main page, the fault is clear.
3. When fault or warning message appears, backlight LED will blinks until the fault or the warning is cleared.

Optional accessory: RJ45 Extension Lead for Digital Keypad
Part No.

Description

CBC-K3FT

RJ45 extension lead, 3 feet (approximately 0.9m)

CBC-K5FT

RJ45 extension lead, 5 feet (approximately 1.5 m)

CBC-K7FT

RJ45 extension lead, 7 feet (approximately 2.1 m)

CBC-K10FT

RJ45 extension lead, 10 feet (approximately 3 m)

CBC-K16FT

RJ45 extension lead, 16 feet (approximately 4.9 m)

Note: When you need to buy communication cables, buy non-shielded , 24 AWG, 4 twisted pair, 100 ohms
communication cables.

10-22

Chapter 10 Digital KeypadC2000

10-3 TPEditor Installation Instruction
TPEditor can edit up to 256 HMI (Human-Machine Interface) pages with a total storage capacity of 256kb.
Each page can edit 50 normal objects and 10 communication objects.

1)

TPEditor: Setup & Basic Functions
1. Run TPEditor version 1.30

2. Go to File(F)Click on New. The Window below will pop up. At the device type, click on the drop down
menu and choose DELTA VFD-C Inverter. At the TP type, click on the drop down menu and choose VFD-C
KeyPad. As for File Name, enter TPE0. Now click on OK.

3. You are now at the designing page. Go to Edit (E)Click on Add a New Page (A) or go to the TP page on
the upper right side, right click once on TP page and choose Add to increase one more page for editing.
The current firmware of Keypad is version1.00 and can support up to 4 pages.

4. Edit Startup Page

10-23

Chapter 10 Digital KeypadC2000 Series

5. Static Text
. Open a blank page, click once on this button
page. The following windows will pop up.

, and then double click on that blank

6. Static Bitmap
Open a blank page, then click once on this button
blank page. The following window will pop up.

and then double click on that

Please note that Static Bitmap setting support only images in BMP format. Now choose a image that
you need and click open, then that image will appear in the Static Bitmap window.
 As shown in the picture on the left side, there
7. Geometric Bitmap
are 11 kinds of geometric bitmap to choose. Open a new blank page then click once on a geometric bitmap
icon that you need. Then drag that icon and enlarge it to the size that you need on that blank page.

10-24

Chapter 10 Digital KeypadC2000
8. Finish editing the keypad starting screen and select Communication>Input User Defined Keypad
Starting Screen.

9. Downloading setting: Go to Tool > Communication. Set up communication port and speed of IFD6530.
10. Only three speed selections are available: 9600 bps, 19200 bps and 38400 bps.

11. When a dialogue box displayed on the screen asking to confirm writing or not, press buttons on the keypad
to go to MENU, select PC LINK and then press ENTER and wait for few seconds. Then select YES on the
screen to start downloading.

10-25

Chapter 10 Digital KeypadC2000 Series

2)

Edit Main Page & Example of Download
1.

Go to editing page, select EditàAdd one page or press the button ADD on the right hand side of the HMI
page to increase number of pages to edit. This keypad currently support up to 256 pages.

2.

On the bottom right-hand corner of the HMI, click on a page number to edit or go to VIEW >HMI page to
start editing main page. As shown in the image, the following objects are available. From left to right:
Static Text, ASCII Display, Static Bitmap, Scale, Bar Graph, Button, Clock Display, Multi-state bit map,
Units, Numeric Input and 11 geometric bitmaps and lines of different width. The application of Static Text,
Static Bitmap, and geometric bitmap is the same as the editing startup page.

3.

Numric/ASCII Display : To add a Numeric/ASCII Display object to a screen, double click on the object to
set up Related Devices, Frame Setting , Fonts and Alignment.

Related Device: Choose the VFD Communication Port that you need, if you want to read output
frequency (H), set the VFD Communication Port to $2202. For other values, please refer to ACMD
ModBus Comm Address List.

10-26

Chapter 10 Digital KeypadC2000
4.

Scale Setting
: On the Tool Bar, click on this
for Scale Setting. You can also edit Scale Setting in
the Property Window on the right hand side of your computer screen.

a.
b.

c.
d.
e.
f.

5.

Scale Position: Click on the drop down list to choose which position that you need to place a scale.
Scale Side: Click on the drop down list to choose if you want to number your scale from smaller
number to bigger number or from big to small. Click OK to accept this setting or click Cancel to
abort.
Font Setting: Click on the drop down list to choose the Font setting that you need then click OK to
accept the setting or click Cancel to abort.
Value Length: Click on the drop down to choose 16bits or 32 bits. Then click OK to accept the
setting or click Cancel to abort.
Main Scale & Sub Scale: In order to divide the whole scale into equal parts, key in the numbers of
your choices for main scale and sub scale.
Maximum value & Minimum Value are the numbers on the two ends of a scale. They can be
negative numbers. But the values allowed to be input are limited by the length of value. For
example, when the length of value is set to be hexadecimal, the maximum and the minimum value
cannot be input as -4000.
Follow the Scale setting mentioned above; you will have a scale as shown below.

Bar Graph setting

a.
b.
c.

:

Related Device: Choose the VFD Communication Port that you need.
Direction Setting: Click on the drop down menu to choose one of the following directions: From
Bottom to Top, From Top to Bottom, From Left to Right or From Right to Left.
Maximum Value & Minimum Value: They define the range covered by the maximum value and
minimum value. If a value is smaller than or equal to the minimum value, then the bar graph will be
blank. If a value is bigger or equal to the maximum value, then the bar graph will be full. If a value is
between minimum and maximum value, then the bar graph will be filled proportionally.

10-27

Chapter 10 Digital KeypadC2000 Series
6.

Button
: Currently this function only allows the Keypad to switch pages, other functions are not yet
available. Text input function and Image inserted functions are not yet supported.
Double click on

to open set up window.

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : snowly.chen
Modify Date                     : 2014:08:26 18:49:34+08:00
Create Date                     : 2014:08:18 10:14:27+08:00
PXC Viewer Info                 : PDF-XChange Viewer;2.5.195.0;Apr 12 2011;18:54:40;D:20140826184934+08'00'
Page Count                      : 692
Has XFA                         : No
XMP Toolkit                     : XMP Core 4.1.1
Format                          : application/pdf
Title                           : Microsoft Word - 01 Receiving
Creator                         : snowly.chen
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2014:08:26 17:32:16+08:00
Producer                        : Acrobat Distiller 9.0.0 (Windows)
Document ID                     : uuid:52223978-1ce0-4314-b7f5-dbb21aa8ded1
Instance ID                     : uuid:13ad2901-01ff-4441-9139-321d5ae38bc0

EXIF Metadata provided by EXIF.tools

01 Receiving Delta_IA MDS_VFD C2000_UM_EN_20140826 Delta IA MDS VFD C2000 UM EN 20140826

Navigation menu

Versions of this User Manual:

Views

Navigation