END SEAL KIT Instructions

User Manual:

Open the PDF directly: View PDF PDF.
Page Count: 2

DownloadEND-SEAL-KIT-instructions
Open PDF In BrowserView PDF
The world’s best-selling electric floor heating brand ™

END SEAL KIT (NAM-END-KIT)
INSTALLATION INSTRUCTIONS

DESCRIPTION
This kit is suitable for use with Warmup NAMSR self-regulating
cable systems. It contains all parts needed to terminate a
cable run. Please refer to the NAMSR installation manual for
maximum circuit lengths.

PRODUCT CONNECTION
PTC Cores
Outer jacket
Copper Braid
Outer jacket

Insulation
Bus wires

Cable with outer jacket for dry and wet conditions

KIT CONTENT
Item

Qty

Description

A

1

Black heat shrink tube (3/4” dia. x 5” length)

B

1

Woven braid sleeve ( ½” dia. x 4” length)

C

1

Black heat shrink cap ( ½” dia. x 1-1/4” length)

A

B

C

WARNING
ELECTRIC SHOCK HAZARD.
Disconnect all power before installing or servicing heating cable and accessories. A qualified person must perform installation and service of
heating cable and accessories.Heating cable must be effectively grounded in accordance with the National Electrical Code. Failure to comply
can result in personal injury or property damage.
Note:
•
All electrical wiring,including GFCI (Ground Fault Circuit Interrupters), must be done according to National Electrical or local codes by a
qualified person.
•
Article 426 of ANSI/NFPA 70 of National Electrical
•
Code (NECSection 62 of CAN/CSA-C22.1, Canadian Electrical Code,Part I (CEC) governs the installation of this heat systems
•
The End Seal Kit is suitable for use with NAMSR heating cables
•
Keep ends of heating devices and kit components dry before and during installation.

OTHER CONNECTION KITS
•

NAM-POWER-KIT

•

NAM-SPLICE-KIT

WARMUP INC.
USA: us@warmup.com
Tel.: 1-888-927-6333
www.warmup.com

CANADA: ca@warmup.com
Tel.: 1-888-592-7687
www.warmup.ca

The world’s best-selling electric floor heating brand ™

The world’s best-selling electric floor heating brand ™

END SEAL KIT (NAM-END-KIT)
INSTALLATION INSTRUCTIONS

1. Score the outer jacket 2” from 4. Pull the pushed-back braid 8. While the shrink tubing is still
the end of the cable. Remove the over the sealed end cap and twist hot, gently squeeze the end of
jacket to expose the braid.
the braid end together.
the shrink tube with pliers and
hold until cool. The end must
remain visibly sealed when the
pliers are removed. If the tube
does not remain sealed, then
repeat steps 7 and 8.

CAUTION: When removing the
outer jacket, be careful not to
damage the braid or the base
cable insulation.

5. Slide the 4” woven braid
sleeving over the end of the
cable, allowing at least 1/2” to
extend past the end of the cable.

2. Push the braid back,and cut off
the end 3/4” of the base cable.
WARNING: ELECTRIC SHOCK
HAZARD.
6. Slide the 5” heat shrink
tubing over the woven braid
piece,allowing 1/2” to extend
past the end of each end of the
woven sleeving.
To prevent short circuits,do not
connect the bus wires together.
Keep braid out of heat shrink cap.
3. Slide the heat shrink cap over
the end of the cable. Apply heat 7. Apply heat evenly to the heat
evenly until it shrinks around the shrink tube unit it shrinks around
the cable.
cable.

WARMUP INC.
USA: us@warmup.com
Tel.: 1-888-927-6333
www.warmup.com

CANADA: ca@warmup.com
Tel.: 1-888-592-7687
www.warmup.ca

The world’s best-selling electric floor heating brand ™
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Create Date                     : 2015:10:19 17:22:40-04:00
Creator                         : Adobe InDesign CS6 (Windows)
Modify Date                     : 2015:10:19 17:22:50-04:00
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Metadata Date                   : 2015:10:19 17:22:50-04:00
Creator Tool                    : Adobe InDesign CS6 (Windows)
Instance ID                     : uuid:2f8c06c5-fcbb-40a4-9fe8-a5e3dee6e026
Original Document ID            : xmp.did:4031EE556476E51195C3B11B0B6A23A0
Document ID                     : xmp.id:880F4E84A776E51198F4AE079C4160DB
Rendition Class                 : proof:pdf
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CS6 (Windows)
History Changed                 : /
History When                    : 2015:10:19 17:22:40-04:00
Derived From Instance ID        : xmp.iid:870F4E84A776E51198F4AE079C4160DB
Derived From Document ID        : xmp.did:4031EE556476E51195C3B11B0B6A23A0
Derived From Original Document ID: xmp.did:4031EE556476E51195C3B11B0B6A23A0
Derived From Rendition Class    : default
Format                          : application/pdf
Producer                        : Adobe PDF Library 10.0.1
Trapped                         : False
Page Count                      : 2
EXIF Metadata provided by EXIF.tools

Navigation menu