EconoAir 2011 A3 Econo Air Gas Fired Heaters A4 X EAIR0411
User Manual: EconoAir Gas Fired Air Heaters-2011 A4-X EAIR0411
Open the PDF directly: View PDF 
.
Page Count: 8
| Download | |
| Open PDF In Browser | View PDF |
EAIR 0411 ECONO-AIR STOKVIS INDUSTRIAL BOILERS (INTERNATIONAL) LIMITED 96R Walton Road East Molesey Surrey KT8 0DL TELEPHONE 020 8783 3050 • FACSIMILE 020 8783 3051 Email: info@stokvisboilers.com • Website: http://www.stokvisboilers.com Direct/Indirect Gas Fired Heating and Ventilation Systems SDF and SIDF SERIES Introduction The Stokvis comprehensive range of gas fired air heaters provides high efficiency combined heating and ventilation solutions across a broad spectrum of industrial and commercial applications. Combined heating and ventilation units ensure precise control, excellent indoor air quality and optimum energy efficiency. The units are available as either direct fired (SDF) or indirect fired (SIDF) to give complete flexibility for optimum design capability. Both the direct fired and indirect fired range of units are fully CE approved and a comprehensive range of optional equipment can be added to the standard models to allow systems to be tailored to meet the requirements for factories, warehouses and other types of large open space buildings. Where applicable the units are currently Energy Technology Listed by the Carbon Trust to allow qualifying users to claim 100% Enhanced Capital Allowances. DIRECT FIRED TECHNICAL DATA MODEL System Types The units are designed to provide the primary heat source across a wide range of applications including: • Ductless air distribution • Air Induction systems • Tempered input ventilation • Industrial make up air • Industrial air displacement ventilation • Pressure ventilation systems Controls To maximise the efficiency of operation Stokvis supply a range of fully integrated control packages to suit each application. Units are supplied fully wired and complete with all starters and contactors etc, plus time and temperature control via an integral Trend controller. Optimised start and stop is included as standard and controls are password protected to prevent unauthorised adjustment. 1 2 3 4 For large open areas the units are available with a wide range of optional air distribution heads to provide ductless air distribution. This is achieved by slightly pressuring the building to ensure very even air distribution both laterally and vertically, thereby eliminating the requirement for extensive distribution duct work and high level de-stratification fan units. and outdoor installation • Model Range and Options • Indirect gas fired units 15kW-900kW • Direct gas fired units 30kW-1200kW • Airflow range 0.5m³/s to 25m³/s • External static pressures up to 2000 pascals depending • • • • • • • • • • on airflow Horizontal units Vertical units Indoor or fully weather proofed outdoor units Variable supply air volume with inverter drives Panel and/or bag filters Mixing box complete with dampers and optional actuators Integral silencer section Optional evaporative cooling module Heat recovery Air distribution heads Maximum air flow m3/s MUA VAV 26 0.51 0.86 SDF2 MUA VAV 53 66 1.03 1.41 SDF3 MUA VAV 66 132 1.79 2.82 SDF4 MUA VAV REC 92 198 2.57 4.00 SDF5 MUA VAV REC 132 264 3.85 5.13 SDF7 MUA VAV REC 198 330 5.13 7.00 SDF9 MUA VAV REC 264 462 6.42 9.00 SDF11 MUA VAV REC 264 594 8.98 11.55 SDF14 MUA VAV REC 396 660 10.27 1400 SDF18 MUA VAV REC 462 924 14.12 18.18 SDF25 MUA VAV REC 594 1056 17.96 25.71 SDF-MUA are fixed volume fresh air units for Make Up Air applications, SDF-VAV models are full fresh air units complete with inverter drive to supply variable air volumes to suit demand. SDF-REC models are complete with patented air recirculation to provide full fresh air or up to 80% recirculation air in variable proportions. Each unit is available with a range of airflows and different burner sizes to give required temperature rise through the units up to a maximum of 42°C ΔT. Maximum airflow for SDF25 REC is 22.5m3/s. Units may be specified to suit alternative airflows and a range of external static pressure requirements up to 400 pascals (dependent on options fitted). For higher static pressures please consult Stokvis. SDF1 • Fully CE approved units for both indoor • • • Minimum air flow m3/s SDF1 MODEL Features and Benefits facilitate use of renewable solar energy Units are supplied fully wired and complete with controls Close temperature control Fully modulating direct gas fired burner control with 20:1 turn down ratio Indirect fired units with turn down ratio of up to 12:1 Std burner size maximum kW output DIRECT FIRED MUA & VAV APPROXIMATE DIMENSIONS Where duct work is required the units can be supplied with either forward or backward curved fans to allow for duct work resistance up to 2000 pascals thereby making them eminently suitable for use with air induction systems. • High thermal efficiency for reduced operating costs • Currently ECA listed models • SFP compliant with current Building regulations • Fully compatible for use with transpired solar panels to Std burner size minimum kW output For smaller systems a SmartCom control panel may be used instead of the Trend control to provide simple user-friendly control with a comprehensive range of features. The units are also fully compatible with BMS systems and alternative BMS Controls maybe integrated within the control strategy. MUA & VAV HORIZONTAL UNITS Width mm Length mm Length C/W filters mm Depth mm Depth C/W filters mm Width mm Height mm 800 860 1800 2420 700 1390 860 2854 • Aircraft hangars • Arenas and exhibition halls • Factory heating and ventilation • Localised air replacement for booths and extract booths • Make-up air for buildings with mechanical exhaust • Sports halls • Swimming pool hall heating and condensation control • Warehouse and distribution centre heating 1 2 3 4 5 Outlet size std fan mm2 Air inlet size h x w mm Aprox weight exc. filters kg 229 600 X 760 225 SDF2 800 860 1800 2420 700 1390 860 2854 322 600 X 760 250 SDF3 1100 1100 2000 2640 1000 1690 1100 3554 453 900 X 1000 300 SDF4 1350 1250 2600 3240 1250 1940 1250 3954 507 1150 X 1150 400 SDF5 1800 1500 2900 3540 1650 2340 1500 4604 638 1550 X 1500 500 SDF7 1800 1500 2900 3540 1650 2340 1500 4604 715 1550 X 1500 515 SDF9 2050 2000 3200 3840 1900 2590 2000 5354 801 1800 X 1900 900 SDF11 2050 2000 3200 3840 1900 2590 2000 5354 898 1800 X 1900 925 SDF14 2350 2200 3500 4140 2200 2930 2200 5854 1007 2100 X 2100 1200 SDF18 2500 2600 3500 4140 2350 3080 2600 6404 1130 2250 X 2500 1400 SDF25 2500 2600 3500 4140 2350 3080 2600 6404 1267 2250 X 2500 1600 MODEL Applications MUA & VAV VETICAL UNITS Height mm REC HORIZONTAL UNITS REC VERTICAL UNITS SDF4 1800 1500 3540 4180 1650 2340 1500 4700 507 1550 X 1400 700 SDF5 1800 1500 3540 4180 1650 2340 1500 4700 638 1550 X 1400 800 SDF7 1800 1500 3850 4490 1650 2340 1500 4700 715 1550 X 1400 900 SDF9 2050 2000 4200 4840 1900 2590 2000 5050 801 1800 X 1900 1100 SDF11 2350 2200 4280 4920 2200 2930 2200 5520 898 2060 X 2060 1350 SDF14 2350 2200 4540 5180 2200 2930 2200 5720 1007 2060 X 2060 1450 SDF18 2500 2600 4640 5280 2350 3080 2600 6020 1130 2210 X 2460 1650 SDF25 2750 2600 4880 5520 2600 3330 2600 6445 1267 2460 X 2460 1800 All dimensions and weights are approximate and should be confirmed with Stokvis. All details are for internal units, please contact Stokvis for external unit information. Filter dimensions include side access panel and/or bag filters. Units will be delivered in sections to suit individual project. External static pressures of up to 2000 Pa are available contact Stokvis for details of non standard units. Direct Fired Units Indirect Fired Units The Principle of Direct Firing – Make-Up Air Indirect Gas Fired Heat Exchanger Where air is extracted from a building either for process or environmental reasons a supply of heated replacement air is required to balance the system and maintain comfort. If make up air is not provided the extract system will perform inefficiently at reduced capacity and a negative pressure will be created. This results in cold air being drawn in around the perimeter of the building and causing cold spots and unpleasant draughts. Stokvis gas fired air heaters incorporate a high efficiency gas fired heating coil with a minimum thermal efficiency of 91% based on NCV, currently qualifying for Enhanced Capital Allowances. For new installations the supply of heated make up air can often provide the required ventilation without the need to install additional extract units. Where matching extract is required this can be integrated in the same unit to supply both input and exhaust with the option of heat recovery from the extract air. Direct gas firing provides a highly efficient method of providing heated replacement air with thermal efficiencies of 100% (based on NCV) and fully modulating burner control withup to 20:1 turndown ratio. The gas fired heating coils have a number of advantages compared to traditional heat exchangers and enable the heat exchanger section to be closely matched with the filter sizes etc. to minimise the airflow resistance and reduce the specific fan power required. The heating coils also provide an excellent turn down ratio for close temperature control. Units are fully CE approved and are supplied with all necessary safety and monitoring controls. Each coil is fitted with a power flue venter and a differential pressure switch which automatically shuts down the burner in the event of a blocked flue or combustion air inlet. Features and Benefits Variable air volume or air recirculation units allow systems to be matched to constantly changing extract rates or to provide full space heating in applications where reduced winter ventilation rates are required. Combined Heating and Ventilation • • • In heating mode Stokvis units provide controlled amounts of fresh air to slightly pressurise the building and the supply air temperature is constantly monitored and adjusted via a fully modulating burner control to optimise the heat input to match the precise building requirements. Close control of the air discharge temperature virtually eliminates heat stratification whilst slight building pressurisation ensures very even distribution both laterally and vertically over large areas, eliminating the requirement for extensive ductwork distribution. • The amount of fresh air automatically adjusts to meet the ventilation requirements of the space. • The units provide the ideal solution to large areas with variable occupancy or industrial heating applications where ventilation rates may change throughout the day. • • In summer mode the units provide 100% fresh air with the large primary air volumes providing improved air change rates for optimum ’free cooling’. Optional evaporative cooling modules may also be added. Features and Benefits • • • • • • • • • • High efficiency for reduced operating costs Fully modulating burner with high turn down ratio (up to 20:1) Close control with rapid response to temperature changes Low maintenance costs Improved indoor air quality Summer fresh air for “free cooling” Alternative model options allows systems to be tailored to suit a wide range of applications Horizontal or vertical units Indoor or fully weather proofed outdoor units Optional evaporative cooling can be added • • Extended heat transfer area for high efficiency and reduced operating costs Reduced operating temperature for enhanced life expectancy Standard coils manufactured from heat resisting stainless steel tube Optional aluminised steel tube heating coils available at reduced cost for units operating on full air recirculation Modular coils utilised on higher output units to avoid the possibility of a complete plant shut down in the event of a burner lockout Enhanced reliability: each burner is fitted with a multi-try ignition system which allows for five ignition attempts with a pre- and post purge on each ignition sequence Pressure switch automatically shuts down the burner in the event of a blocked flue or combustion air inlet Alternative wall or roof flue terminations Simple wall flue outlet reduces installation costs, eliminating roof penetrations and potential roof leaks Model Range and Options • • • • • • • • • • • Heat outputs 15kW-900kW Airflow range 1m³/s to 22m³/s External static pressures up to 2000 pascals depending on airflow Horizontal units Vertical units Indoor or fully weather proofed outdoor units Panel and/or bag filters Mixing box complete with dampers and optional actuators Integral silencer section Heat recovery Air distribution heads SDF/MUA SDF/VAV 100% Fresh air Constant volume direct fired make up air (MUA) heaters to provide a fixed rate of heated fresh air to the space. The units are ideal for supplying heating and make up air to large areas or to individual spray booths etc, where constant extract rates are used. Generally units are sized to introduce slightly more make up air into the space than the extract air volume. A balanced amount of make up air can provide a slight positive pressure to distribute the air uniformly throughout the building and eliminate random air infiltration. For special applications such as kitchen make up air and certain industrial processes where the transfer of odours or dust etc to surrounding areas needs to be avoided, the volume of make up air supplied is lower than the extract rate. SDF/REC Variable volume fresh air The variable air volume (VAV) models allow the volume of heated make up air to vary to suit the changing requirements of the building orchanging exhaust rates. The units are fitted with a special box burner system complete with integral fan(s) to ensure optimum combustion throughout the range of varying volume main air supply. The units supply 100% fresh air at all times but the volume of fresh air is automatically adjusted either by the application of a building pressure sensor or temperature sensors. The building pressure sensor can be set to maintain either a slight positive or negative pressure inside the building to suit the requirements of the application. When used for space heating, temperature sensors adjust both the air discharge temperature and the supply air volume to provide a rapid warm up and maintain minimal stratification levels. 80 – 100% Recirculating air 20 – 100% Fresh air Variable air recirculation (REC) models are fully CE approved and patented. They provide a constant air volume with up to 80% recirculation air. The variable air recirculation option combines a constant supply of 20% fresh air which passes over the burner with the remaining air volume being either fresh air, recirculation air or a mixture of fresh and recirculated air. The variable percentage of fresh air and recirculation air is accurately controlled via a fully modulating face and bypass damper with fresh air introduced using the burner section and recirculation air via an integral bypass. The fully modulating burner and damper control functions are integrated via a microprocessor control to co-ordinate the heating and ventilation functions. The system can provide variable make-up air, full building heating or a combination of both, controlled via building pressure sensors and temperature sensors to respond automatically to building pressure and temperature requirements. SDF / SIDF Series GAS FIRED COMBINED HEATING AND VENTILATION Specification Typical Indirect Fired Unit Heater Anodised aluminium framework with optional infill panels. Option 1 Mineral wool insulation (0.03w/mk), panel weight 16kg/m2. Option 2 Eco panels with enhanced insulation (0.024w/mk). Patented hydrotec water formulated polyurethane foam provides enhanced insulation and reduced weight of 8kg/m2. The injection process guarantees continuity of thickness and adhesion to provide excellent panel rigidity, whilst integral double edge sealing provides improved air tightness. Indirect gas fired sections comprise of CE certified coils. The gas fired coils provide high efficiency with high turndown ratio. Direct gas fired sections are fully CE certified and provide 100% efficiency (NCV) and a turn down ratio of up to 20:1. Direct fired units provide the ideal energy efficient solution for applications requiring permanent ventilation or for buildings with higher air infiltration rates. All service panels are hinged for ease of access, with fan and burner compartment sections coming complete with locks. Wide choice of both panel and bag filters. Galvanised base frame complete with lifting access points and levelling bolts. Standard units are supplied complete with all wiring and controls. Fans and motors are mounted on a separate base frame complete with anti-vibration mounts and flexible connections. Aluminium aerofoil section dampers complete with edge seals for precise control of fresh air and recirculation air. A comprehensive range of damper actuators may be factory fitted and wired to provide occupancy ventilation or fresh air free cooling SDF / SIDF Series GAS FIRED COMBINED HEATING AND VENTILATION Specification Typical Indirect Fired Unit Heater Anodised aluminium framework with optional infill panels. Option 1 Mineral wool insulation (0.03w/mk), panel weight 16kg/m2. Option 2 Eco panels with enhanced insulation (0.024w/mk). Patented hydrotec water formulated polyurethane foam provides enhanced insulation and reduced weight of 8kg/m2. The injection process guarantees continuity of thickness and adhesion to provide excellent panel rigidity, whilst integral double edge sealing provides improved air tightness. Indirect gas fired sections comprise of CE certified coils. The gas fired coils provide high efficiency with high turndown ratio. Direct gas fired sections are fully CE certified and provide 100% efficiency (NCV) and a turn down ratio of up to 20:1. Direct fired units provide the ideal energy efficient solution for applications requiring permanent ventilation or for buildings with higher air infiltration rates. All service panels are hinged for ease of access, with fan and burner compartment sections coming complete with locks. Wide choice of both panel and bag filters. Galvanised base frame complete with lifting access points and levelling bolts. Standard units are supplied complete with all wiring and controls. Fans and motors are mounted on a separate base frame complete with anti-vibration mounts and flexible connections. Aluminium aerofoil section dampers complete with edge seals for precise control of fresh air and recirculation air. A comprehensive range of damper actuators may be factory fitted and wired to provide occupancy ventilation or fresh air free cooling Direct Fired Units Indirect Fired Units The Principle of Direct Firing – Make-Up Air Indirect Gas Fired Heat Exchanger Where air is extracted from a building either for process or environmental reasons a supply of heated replacement air is required to balance the system and maintain comfort. If make up air is not provided the extract system will perform inefficiently at reduced capacity and a negative pressure will be created. This results in cold air being drawn in around the perimeter of the building and causing cold spots and unpleasant draughts. Stokvis gas fired air heaters incorporate a high efficiency gas fired heating coil with a minimum thermal efficiency of 91% based on NCV, currently qualifying for Enhanced Capital Allowances. For new installations the supply of heated make up air can often provide the required ventilation without the need to install additional extract units. Where matching extract is required this can be integrated in the same unit to supply both input and exhaust with the option of heat recovery from the extract air. Direct gas firing provides a highly efficient method of providing heated replacement air with thermal efficiencies of 100% (based on NCV) and fully modulating burner control withup to 20:1 turndown ratio. The gas fired heating coils have a number of advantages compared to traditional heat exchangers and enable the heat exchanger section to be closely matched with the filter sizes etc. to minimise the airflow resistance and reduce the specific fan power required. The heating coils also provide an excellent turn down ratio for close temperature control. Units are fully CE approved and are supplied with all necessary safety and monitoring controls. Each coil is fitted with a power flue venter and a differential pressure switch which automatically shuts down the burner in the event of a blocked flue or combustion air inlet. Features and Benefits Variable air volume or air recirculation units allow systems to be matched to constantly changing extract rates or to provide full space heating in applications where reduced winter ventilation rates are required. Combined Heating and Ventilation • • • In heating mode Stokvis units provide controlled amounts of fresh air to slightly pressurise the building and the supply air temperature is constantly monitored and adjusted via a fully modulating burner control to optimise the heat input to match the precise building requirements. Close control of the air discharge temperature virtually eliminates heat stratification whilst slight building pressurisation ensures very even distribution both laterally and vertically over large areas, eliminating the requirement for extensive ductwork distribution. • The amount of fresh air automatically adjusts to meet the ventilation requirements of the space. • The units provide the ideal solution to large areas with variable occupancy or industrial heating applications where ventilation rates may change throughout the day. • • In summer mode the units provide 100% fresh air with the large primary air volumes providing improved air change rates for optimum ’free cooling’. Optional evaporative cooling modules may also be added. Features and Benefits • • • • • • • • • • High efficiency for reduced operating costs Fully modulating burner with high turn down ratio (up to 20:1) Close control with rapid response to temperature changes Low maintenance costs Improved indoor air quality Summer fresh air for “free cooling” Alternative model options allows systems to be tailored to suit a wide range of applications Horizontal or vertical units Indoor or fully weather proofed outdoor units Optional evaporative cooling can be added • • Extended heat transfer area for high efficiency and reduced operating costs Reduced operating temperature for enhanced life expectancy Standard coils manufactured from heat resisting stainless steel tube Optional aluminised steel tube heating coils available at reduced cost for units operating on full air recirculation Modular coils utilised on higher output units to avoid the possibility of a complete plant shut down in the event of a burner lockout Enhanced reliability: each burner is fitted with a multi-try ignition system which allows for five ignition attempts with a pre- and post purge on each ignition sequence Pressure switch automatically shuts down the burner in the event of a blocked flue or combustion air inlet Alternative wall or roof flue terminations Simple wall flue outlet reduces installation costs, eliminating roof penetrations and potential roof leaks Model Range and Options • • • • • • • • • • • Heat outputs 15kW-900kW Airflow range 1m³/s to 22m³/s External static pressures up to 2000 pascals depending on airflow Horizontal units Vertical units Indoor or fully weather proofed outdoor units Panel and/or bag filters Mixing box complete with dampers and optional actuators Integral silencer section Heat recovery Air distribution heads SDF/MUA SDF/VAV 100% Fresh air Constant volume direct fired make up air (MUA) heaters to provide a fixed rate of heated fresh air to the space. The units are ideal for supplying heating and make up air to large areas or to individual spray booths etc, where constant extract rates are used. Generally units are sized to introduce slightly more make up air into the space than the extract air volume. A balanced amount of make up air can provide a slight positive pressure to distribute the air uniformly throughout the building and eliminate random air infiltration. For special applications such as kitchen make up air and certain industrial processes where the transfer of odours or dust etc to surrounding areas needs to be avoided, the volume of make up air supplied is lower than the extract rate. SDF/REC Variable volume fresh air The variable air volume (VAV) models allow the volume of heated make up air to vary to suit the changing requirements of the building orchanging exhaust rates. The units are fitted with a special box burner system complete with integral fan(s) to ensure optimum combustion throughout the range of varying volume main air supply. The units supply 100% fresh air at all times but the volume of fresh air is automatically adjusted either by the application of a building pressure sensor or temperature sensors. The building pressure sensor can be set to maintain either a slight positive or negative pressure inside the building to suit the requirements of the application. When used for space heating, temperature sensors adjust both the air discharge temperature and the supply air volume to provide a rapid warm up and maintain minimal stratification levels. 80 – 100% Recirculating air 20 – 100% Fresh air Variable air recirculation (REC) models are fully CE approved and patented. They provide a constant air volume with up to 80% recirculation air. The variable air recirculation option combines a constant supply of 20% fresh air which passes over the burner with the remaining air volume being either fresh air, recirculation air or a mixture of fresh and recirculated air. The variable percentage of fresh air and recirculation air is accurately controlled via a fully modulating face and bypass damper with fresh air introduced using the burner section and recirculation air via an integral bypass. The fully modulating burner and damper control functions are integrated via a microprocessor control to co-ordinate the heating and ventilation functions. The system can provide variable make-up air, full building heating or a combination of both, controlled via building pressure sensors and temperature sensors to respond automatically to building pressure and temperature requirements. SDF and SIDF SERIES Introduction The Stokvis comprehensive range of gas fired air heaters provides high efficiency combined heating and ventilation solutions across a broad spectrum of industrial and commercial applications. Combined heating and ventilation units ensure precise control, excellent indoor air quality and optimum energy efficiency. The units are available as either direct fired (SDF) or indirect fired (SIDF) to give complete flexibility for optimum design capability. Both the direct fired and indirect fired range of units are fully CE approved and a comprehensive range of optional equipment can be added to the standard models to allow systems to be tailored to meet the requirements for factories, warehouses and other types of large open space buildings. Where applicable the units are currently Energy Technology Listed by the Carbon Trust to allow qualifying users to claim 100% Enhanced Capital Allowances. DIRECT FIRED TECHNICAL DATA MODEL System Types The units are designed to provide the primary heat source across a wide range of applications including: • Ductless air distribution • Air Induction systems • Tempered input ventilation • Industrial make up air • Industrial air displacement ventilation • Pressure ventilation systems Controls To maximise the efficiency of operation Stokvis supply a range of fully integrated control packages to suit each application. Units are supplied fully wired and complete with all starters and contactors etc, plus time and temperature control via an integral Trend controller. Optimised start and stop is included as standard and controls are password protected to prevent unauthorised adjustment. 1 2 3 4 For large open areas the units are available with a wide range of optional air distribution heads to provide ductless air distribution. This is achieved by slightly pressuring the building to ensure very even air distribution both laterally and vertically, thereby eliminating the requirement for extensive distribution duct work and high level de-stratification fan units. and outdoor installation • Model Range and Options • Indirect gas fired units 15kW-900kW • Direct gas fired units 30kW-1200kW • Airflow range 0.5m³/s to 25m³/s • External static pressures up to 2000 pascals depending • • • • • • • • • • on airflow Horizontal units Vertical units Indoor or fully weather proofed outdoor units Variable supply air volume with inverter drives Panel and/or bag filters Mixing box complete with dampers and optional actuators Integral silencer section Optional evaporative cooling module Heat recovery Air distribution heads Maximum air flow m3/s MUA VAV 26 0.51 0.86 SDF2 MUA VAV 53 66 1.03 1.41 SDF3 MUA VAV 66 132 1.79 2.82 SDF4 MUA VAV REC 92 198 2.57 4.00 SDF5 MUA VAV REC 132 264 3.85 5.13 SDF7 MUA VAV REC 198 330 5.13 7.00 SDF9 MUA VAV REC 264 462 6.42 9.00 SDF11 MUA VAV REC 264 594 8.98 11.55 SDF14 MUA VAV REC 396 660 10.27 1400 SDF18 MUA VAV REC 462 924 14.12 18.18 SDF25 MUA VAV REC 594 1056 17.96 25.71 SDF-MUA are fixed volume fresh air units for Make Up Air applications, SDF-VAV models are full fresh air units complete with inverter drive to supply variable air volumes to suit demand. SDF-REC models are complete with patented air recirculation to provide full fresh air or up to 80% recirculation air in variable proportions. Each unit is available with a range of airflows and different burner sizes to give required temperature rise through the units up to a maximum of 42°C ΔT. Maximum airflow for SDF25 REC is 22.5m3/s. Units may be specified to suit alternative airflows and a range of external static pressure requirements up to 400 pascals (dependent on options fitted). For higher static pressures please consult Stokvis. SDF1 • Fully CE approved units for both indoor • • • Minimum air flow m3/s SDF1 MODEL Features and Benefits facilitate use of renewable solar energy Units are supplied fully wired and complete with controls Close temperature control Fully modulating direct gas fired burner control with 20:1 turn down ratio Indirect fired units with turn down ratio of up to 12:1 Std burner size maximum kW output DIRECT FIRED MUA & VAV APPROXIMATE DIMENSIONS Where duct work is required the units can be supplied with either forward or backward curved fans to allow for duct work resistance up to 2000 pascals thereby making them eminently suitable for use with air induction systems. • High thermal efficiency for reduced operating costs • Currently ECA listed models • SFP compliant with current Building regulations • Fully compatible for use with transpired solar panels to Std burner size minimum kW output For smaller systems a SmartCom control panel may be used instead of the Trend control to provide simple user-friendly control with a comprehensive range of features. The units are also fully compatible with BMS systems and alternative BMS Controls maybe integrated within the control strategy. MUA & VAV HORIZONTAL UNITS Width mm Length mm Length C/W filters mm Depth mm Depth C/W filters mm Width mm Height mm 800 860 1800 2420 700 1390 860 2854 • Aircraft hangars • Arenas and exhibition halls • Factory heating and ventilation • Localised air replacement for booths and extract booths • Make-up air for buildings with mechanical exhaust • Sports halls • Swimming pool hall heating and condensation control • Warehouse and distribution centre heating 1 2 3 4 5 Outlet size std fan mm2 Air inlet size h x w mm Aprox weight exc. filters kg 229 600 X 760 225 SDF2 800 860 1800 2420 700 1390 860 2854 322 600 X 760 250 SDF3 1100 1100 2000 2640 1000 1690 1100 3554 453 900 X 1000 300 SDF4 1350 1250 2600 3240 1250 1940 1250 3954 507 1150 X 1150 400 SDF5 1800 1500 2900 3540 1650 2340 1500 4604 638 1550 X 1500 500 SDF7 1800 1500 2900 3540 1650 2340 1500 4604 715 1550 X 1500 515 SDF9 2050 2000 3200 3840 1900 2590 2000 5354 801 1800 X 1900 900 SDF11 2050 2000 3200 3840 1900 2590 2000 5354 898 1800 X 1900 925 SDF14 2350 2200 3500 4140 2200 2930 2200 5854 1007 2100 X 2100 1200 SDF18 2500 2600 3500 4140 2350 3080 2600 6404 1130 2250 X 2500 1400 SDF25 2500 2600 3500 4140 2350 3080 2600 6404 1267 2250 X 2500 1600 MODEL Applications MUA & VAV VETICAL UNITS Height mm REC HORIZONTAL UNITS REC VERTICAL UNITS SDF4 1800 1500 3540 4180 1650 2340 1500 4700 507 1550 X 1400 700 SDF5 1800 1500 3540 4180 1650 2340 1500 4700 638 1550 X 1400 800 SDF7 1800 1500 3850 4490 1650 2340 1500 4700 715 1550 X 1400 900 SDF9 2050 2000 4200 4840 1900 2590 2000 5050 801 1800 X 1900 1100 SDF11 2350 2200 4280 4920 2200 2930 2200 5520 898 2060 X 2060 1350 SDF14 2350 2200 4540 5180 2200 2930 2200 5720 1007 2060 X 2060 1450 SDF18 2500 2600 4640 5280 2350 3080 2600 6020 1130 2210 X 2460 1650 SDF25 2750 2600 4880 5520 2600 3330 2600 6445 1267 2460 X 2460 1800 All dimensions and weights are approximate and should be confirmed with Stokvis. All details are for internal units, please contact Stokvis for external unit information. Filter dimensions include side access panel and/or bag filters. Units will be delivered in sections to suit individual project. External static pressures of up to 2000 Pa are available contact Stokvis for details of non standard units. EAIR 0411 ECONO-AIR STOKVIS INDUSTRIAL BOILERS (INTERNATIONAL) LIMITED 96R Walton Road East Molesey Surrey KT8 0DL TELEPHONE 020 8783 3050 • FACSIMILE 020 8783 3051 Email: info@stokvisboilers.com • Website: http://www.stokvisboilers.com Direct/Indirect Gas Fired Heating and Ventilation Systems
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Has XFA : No XMP Toolkit : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00 Create Date : 2011:04:28 16:30:19+01:00 Modify Date : 2011:05:16 13:34:16+01:00 Metadata Date : 2011:05:16 13:34:16+01:00 Creator Tool : Adobe InDesign CS3 (5.0) Thumbnail Format : JPEG Thumbnail Width : 256 Thumbnail Height : 256 Thumbnail Image : (Binary data 16555 bytes, use -b option to extract) Version ID : 1 Instance ID : uuid:591837b8-8f0e-4254-99c8-4cf241f7e155 Document ID : adobe:docid:indd:90ce6dd3-6988-11e0-903e-df6408956c53 Rendition Class : proof:pdf Derived From Instance ID : 79620851-6813-11e0-8197-997d9e52079d Derived From Document ID : adobe:docid:indd:1c5cb7d5-6270-11e0-a9ff-dcf6d349a6d6 Derived From Version ID : 1 Manifest Link Form : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream Manifest Placed X Resolution : 300.00, 300.00, 300.00, 300.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 343.00, 150.00, 72.00, 72.00, 72.00, 300.00, 300.00, 72.00, 300.00, 300.00, 343.00, 300.00, 300.00, 300.00 Manifest Placed Y Resolution : 300.00, 300.00, 300.00, 300.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 343.00, 150.00, 72.00, 72.00, 72.00, 300.00, 300.00, 72.00, 300.00, 300.00, 343.00, 300.00, 300.00, 300.00 Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches Manifest Reference Instance ID : xmp.iid:777FE3E69061E011B4D78ED69DA74DCC, xmp.iid:727FE3E69061E011B4D78ED69DA74DCC, xmp.iid:787FE3E69061E011B4D78ED69DA74DCC, xmp.iid:0B154F06FA64E0118E788D535E5ADDE4, xmp.iid:AA045C239362E01197D3DFFBB310DFCC, uuid:38bd4204-91b8-11d7-a776-e837ff04c337, uuid:E40D2408CE28DD119D7CE7ACEFA885B5, uuid:DEB4B441CE28DD119D7CE7ACEFA885B5, uuid:DD0D2408CE28DD119D7CE7ACEFA885B5, uuid:5AB0BC20CE28DD119D7CE7ACEFA885B5, uuid:0C094878CE28DD119D7CE7ACEFA885B5, uuid:C374836189FED911B724BDEFADA6420C, xmp.iid:A8045C239362E01197D3DFFBB310DFCC, uuid:1BE4A5D4CD28DD119D7CE7ACEFA885B5, xmp.iid:0C154F06FA64E0118E788D535E5ADDE4, uuid:437B247AA367E011AC92BC141529BAF1, uuid:5af37174-830d-4881-a8ad-44d75ae57297, uuid:fa9518b5-f13d-41b7-a9dd-14619fd5215e, uuid:a1f89ac4-c4fb-4c97-b70e-b80b74ac98c5, xmp.iid:B1FF300BA461E011B4D78ED69DA74DCC, xmp.iid:0A154F06FA64E0118E788D535E5ADDE4, uuid:20abc37c-7943-4765-a592-ad5abf37c917, xmp.iid:73BC8929EF64E0118E788D535E5ADDE4, xmp.iid:70BC8929EF64E0118E788D535E5ADDE4, xmp.iid:0C154F06FA64E0118E788D535E5ADDE4, xmp.iid:19C98B1DBB61E011B4D78ED69DA74DCC, xmp.iid:16C98B1DBB61E011B4D78ED69DA74DCC, xmp.iid:17C98B1DBB61E011B4D78ED69DA74DCC Manifest Reference Document ID : xmp.did:757FE3E69061E011B4D78ED69DA74DCC, xmp.did:6F7FE3E69061E011B4D78ED69DA74DCC, xmp.did:737FE3E69061E011B4D78ED69DA74DCC, uuid:6e82c9c7-2440-45b2-8033-0fee10806166, adobe:docid:indd:1c5cb7d5-6270-11e0-a9ff-dcf6d349a6d6, adobe:docid:photoshop:ec86f767-91b6-11d7-a776-e837ff04c337, adobe:docid:photoshop:578c436b-26c8-11d7-b345-d60d87dcec0e, uuid:D3CC46D8AC16DD118CF5C5656FE0A092, adobe:docid:photoshop:578c436c-26c8-11d7-b345-d60d87dcec0e, adobe:docid:photoshop:578c4367-26c8-11d7-b345-d60d87dcec0e, adobe:docid:photoshop:578c4369-26c8-11d7-b345-d60d87dcec0e, uuid:C274836189FED911B724BDEFADA6420C, adobe:docid:indd:b38ac1c9-5fac-11e0-bbb9-80365c0c0944, adobe:docid:indd:ece1b24f-06e9-11dd-8830-d560acc41b1d, xmp.did:ECDB4E4ADC64E011BD57FE2F0F99E232, uuid:40f67086-81f1-49ea-b71f-722753729d47, uuid:83E7B265A061E0119C08A6896D158B3D, uuid:81E7B265A061E0119C08A6896D158B3D, uuid:86E7B265A061E0119C08A6896D158B3D, xmp.did:ACFF300BA461E011B4D78ED69DA74DCC, uuid:6e82c9c7-2440-45b2-8033-0fee10806166, uuid:EB8A30E1AD61E011BE92E7D7C36822E3, uuid:6e82c9c7-2440-45b2-8033-0fee10806166, uuid:6e82c9c7-2440-45b2-8033-0fee10806166, xmp.did:ECDB4E4ADC64E011BD57FE2F0F99E232, xmp.did:18C98B1DBB61E011B4D78ED69DA74DCC, xmp.did:478B5022A861E011B4D78ED69DA74DCC, xmp.did:438B5022A861E011B4D78ED69DA74DCC Manifest Reference Version ID : 1 Format : application/pdf Title : EconoAir-2011 A3.indd Producer : Adobe PDF Library 8.0 Trapped : False GTS PDFX Version : PDF/X-4 Page Count : 8 Creator : Adobe InDesign CS3 (5.0)EXIF Metadata provided by EXIF.tools