EBZ7100 Engine Blower Workshop Manual

EBZ7100RH 1076283488%5CEngine_Blower_Workshop_Manual

User Manual: EBZ7100

Open the PDF directly: View PDF .
Page Count: 66

Instruction

This workshop manual describes the main maintenance items and procedures and

troubleshooting for the Husqvarna Zenoah engine blower.

This manual is classified into two categories; one includes important notices concerning

disassembly and reassembly including "Cautions for disassembly" and "Cautions for

reassembly", the other includes inspection and adjustment items such as "Muffler inspection

and maintenance", "Air cleaner inspection" and "Carburetor adjustment". After each item is

thoroughly understood, apply the understanding to the actual maintenance tasks.

Frequently asked questions are also included in this manual. However, many cases need rich

maintenance experience and informed judgment. Please refer to this manual for maintenance

support.

【

【【

【NOTES】

】】

】

1. The contents of this manual are based on specifications as of January 2009.

The contents may be modified due to performance improvement or some other reason

without notice.

2. Use Zenoah brand-name parts when replacing a part during maintenance, etc.

The manufacturer does not bear any responsibility if trouble occurs during parts use of other

than brand-name parts.

3. Read this manual thoroughly before beginning the maintenance work, understand it, apply

the content to the actual maintenance tasks and guide the customer if directions, are

needed.

Exported models according to country

This workshop manual applies to all exported engine blower models sold by Hasqvarna

Zenoah. Some models are not exported to particular regions of the world. Please check your

model by referring the following table.

Table of exported models corresponding to country

Category Handheld Blower Backpack Blower

Displacement 22.5 cm3 25.4 cm3 29.5 cm3 41.5 cm3 47.9 cm3 50.2 cm3 62.0 cm3 64.9 cm3 71.9 cm3

Engine Type G23L GZ25N GZ30N G4K GZ48N GZ51N G62L GZ65N GZ72N

JAP HB2311EZ EBZ3000 EB4300★ EBZ4800 EB7001★

General HB2302 HBZ2601 EBZ3000 EB4300 EB6200

EB7000

EBZ8001＊2

EU HB2302 HBZ2601 EBZ3000 EBZ4800 EB7000 EBZ8001＊2

Blower

Model

USA HBZ2601 EBZ3000RH

EBZ3050RH

EBZ5100★

EBZ5100RH

EBZ5100Q★＊1

EBZ5150★

EBZ5150RH

EBZ5150Q★＊1

EBZ7100★

EBZ7100RH

EBZ7150★

EBZ7150RH

EBZ8001★

EBZ8001RH

EBZ8050★

EBZ8050RH

★: Left hand throttle lever specifications

＊1: EBZ5100Q has low noise specifications.

＊2: Equipped with frame for the mist kit installation.

Model Notation

The engine type and blower model nomenclature is as follows.

The applicable blower models and series names are indicated at right of the maintenance item

title. Refer to this nomenclature to confirm engine type and blower model.

●

●●

● Engine Type

G Z 25 N

Engine series (L/ N/ K)

Displacement (cm3)

Strato charged engine (green engine)

●

●●

● Blower Model

HB Z 26 01

Minor changed code

Handheld Bower

EB Z 71 00

Backpack (shouldering type) Blower

EB Z 51 00 RH

Right hand throttle lever specification

EB Z 51 00 Q

Low noise specifications

EB Z 51 50

Evaporation tank (fluorine coated) specification

(Since January, 2009.)

Contents

1. Special Features ............................................................................................................ 1

2. Specifications and Technical Data

2-1 Blower ........................................................................................................................... 2

2-2 Pipe ............................................................................................................................... 3

2-3 Overall dimensions ........................................................................................................ 4

3. Special Tools

3-1 Rotor Removal .............................................................................................................. 5

3-2 Module Assembly ........................................................................................................ 11

3-3 Recoil Pulley Removal ................................................................................................ 14

3-4 Piston Pin Removal ..................................................................................................... 15

4. Service Guide

4-1 Starter Pulley Removal ............................................................................................... 17

4-2 Air Inlet Net Removal .................................................................................................. 17

4-3 Upper Spring Damper Removal .................................................................................. 18

4-4 Volute Cover Lower Damper Removal ........................................................................ 19

4-5 Flywheel Side Crankshaft Removal ............................................................................ 19

4-6 Crankcase Oil Seal and Bearings Removal ................................................................ 20

4-7 Crankcase Assembling ............................................................................................... 21

4-8 Piston Inserting Direction ............................................................................................ 24

4-9 Piston Pin Snap Ring Assembly ................................................................................ 24

4-10 Positioning of Lead Air Intake Tube .......................................................................... 25

4-11 Reed Valve Assembly ............................................................................................... 25

4-12 Gasket Assembly ...................................................................................................... 26

4-13 Scavenging Duct Cover Assembly ............................................................................ 27

4-14 Muffler Assembly ....................................................................................................... 27

4-15 Switch Cord Assembly .............................................................................................. 28

4-16 Cable Wiring .............................................................................................................. 30

4-17 Fan Assembly ........................................................................................................... 31

4-18 Backpack Pad Air Supply Pipe Assembly ................................................................. 31

4-19 Upper Spring Damper Assembly .............................................................................. 31

4-20 Upper Damper Assembly .......................................................................................... 32

4-21 Lower Damper Assembly .......................................................................................... 32

4-22 Carburetor Assembly ................................................................................................ 33

4-23 Engine Cover Assembly ............................................................................................ 33

4-24 Check of the Gasket Assembly ................................................................................. 34

4-25 Spark Arrester Removal ............................................................................................ 35

4-26 Spark Arrester Cleaning ............................................................................................ 36

4-27 Muffler Cleaning ........................................................................................................ 36

4-28 Air Cleaner Inspection ............................................................................................... 37

4-29 Element Removal ...................................................................................................... 37

4-30 Element Cleaning ...................................................................................................... 39

5. Structure of Right Hand Throttle Lever ............................................................. 40

6. Carburetor

6-1 Specifications .............................................................................................................. 41

6-2 Carburetor Configuration ............................................................................................ 42

6-3 Carburetor Conforms to Exhaust Emissions Regulations .......................................... 43

6-4 Limiter Cap Removal/ Installation ............................................................................... 44

6-5 Idling Speed Adjustment ............................................................................................. 44

6-6 Carburetor Inspection ................................................................................................. 45

6-7 Carburetor Adjustment ................................................................................................ 47

7. Maintenance Standards

7-1 Engine ......................................................................................................................... 51

7-2 Tightening Torques ...................................................................................................... 52

8. Troubleshooting

8-1 Engine does not start .................................................................................................. 53

8-2 Engine stop during operation ...................................................................................... 53

8-3 Engine cannot be stopped .......................................................................................... 53

8-4 Lack of output power or unstable revolution ............................................................... 54

8-5 The amount of the wind is weak ................................................................................. 54

1

1. Special Features

The environmental friendly Strato

Charge Engine is installed.

The exhaust gas toxin concentration is greatly

reduced without need for a catalyst, to generate

reactive heat. High engine cooling performance

promotes stable output even during continuous

operation in summer. Furthermore, low fuel

consumption reduces running costs.

Strato Charged: It means prior air intake and

layered scavenging system.

Strato charged engine installed models:

HBZ2601

EBZ3000

EBZ4800

EBZ5100

EBZ5100Q

EBZ7100

EBZ8001

The fan is designed to deliver air

efficiently and silently.

Usually an open type fan is used,

whose vanes are bare. Some

fans have closed construction

whose vane edges are joined to a

plate.

The closed vane fan will deliver a

larger airflow compared to the

same sized conventional open

vane fan.

Closed vane fan installed model:

EBZ8001

The backpack blower has air ventilation system between the blower's pad

and operator's back to reduce sweating and ensure comfortable operation.

Exhaust Type:

Cools the operator's back by

exhausting air between the blower's

pad and operator's back.

Exhaust models:

EB4300/ EBZ4800/ EBZ5100 Series

EB6200/ EB7000/ EB7001/ EBZ7100

Inhalation Type:

Cools the operator's back by

sucking air between the blower's

pad and operator's back.

Inhalation models:

EBZ3000 EBZ8001

A large air cleaner, incomparable to other manufacturer's models,

is installed. The large air cleaner consist of two stage filters

(pre-filter and paper filter).

An extended cleaning interval compared to conventional models

ensures easier maintenance and trouble-free operation.

●

●●

● Air cleaner performance: Twice that of conventional models.

●

●●

● Cleaning interval: Three times longer than any other

manufacturer's blower of the same class.

Large air cleaner employing models:

EB7000

EB7001

EBZ7100

EBZ8001

V

olute Case

Frame

Guard Net

Engine Centrifugal Fan

Guard Net

Open Vane Fan

Closed Vane Fan

Backpack Pad Ventilation

Large Air Cleaner

Nozzle Shapes of the Pipe End Main Purpose

A larger diameter promotes

voluminous air blowing.

It is suitable for blowing

withering fallen leaves, paper

trash and other light material.

A narrower nozzle generates

higher air pressure.

It is suitable for blowing trimmed

turf, pine needles and other

moist or weighty material.

A wide nozzle spreads the

blown air.

It is suitable for trimmed turf and

fallen leaves that stick to the

ground.

Noise Comparison between Models

Pipe End Specifications and Characteristics

Model

Noise dB (A)

15 m (49 ft)

from the

blower

Noise

level

EBZ4800 67 Low

EBZ5100Q 68

HBZ2601 69

EBZ3000 69

HB2302/ 2311 70

HBZ2601CA 72

EBZ5100 71

EB4300 74

EB6200/ 7000/ 7001 75

EBZ7100 77

EBZ8001 77 High

Pre-filter

Air Cleaner Cover

paper Filter

Air Cleaner Body

Fuel/ air mixture

and pure air are

separately induced

durin

g

p

iston

Firstly pure air is

inhaled, then fuel/

air mixture is

inhaled.

A pure air layer

forms to push out

the burnt gasses

resulting in a

reduced volume of

unburnt exhaust

gasses.

V

entilation

φ

φφ

φ72 mm (2.84 in.)/

φ

φφ

φ66 mm (2.60in.)

φ

φφ

φ57 mm (2.24 in.)

B

A

Duckbill Nozzle

Dimensions (A x B)

Small nozzle: 23x138 mm (0.91x5.43 in.)

Large nozzle: 30x180 mm (1.18x7.09 in.)

Pipe End

φ

φφ

φ72 mm (2.84 in.)/

φ

φφ

φ66 mm (2.60in.)

Pipe End

φ

φφ

φ57 mm (2.24 in.)

Duckbill Nozzle

Operating area

To prevent leaves, dirt or foreign matter being

drawn in, a net is set between the volute cover

and the frame.

If leaves or dirt block at the net and the air

intake, airflow and blower cooling efficiency will

be reduced resulting in overheating.

Guard net installed models:

EBZ3000

EBZ4800

EBZ5100

EBZ5100Q

EB7000

EB7001

EBZ7100

EBZ8001

15 m

(49 ft)

Under ANSI B175.2-2000; (8 points measurement)

15 m

(49 ft)

2

2. Specifications and Technical Data

2-1 Blower ★：

★：★：

★：Left hand throttle lever specifications

Item Unit Specifications

Category Handheld Blower Backpack Blower

Engine Type G23L GZ25N GZ30N G4K GZ48N GZ51N G62L GZ65N GZ72N

HB23 Series HBZ26 Series EBZ30 Series －

－－

－ －

－－

－ EBZ51 Series －

－－

－ EB70 Series EBZ71 Series EBZ80 Series

EBZ3000 EBZ8001

Blower Model HB2302 HB2311EZ HBZ2601 HBZ2601

EBZ3000RH/

EBZ3050RH

EB4300 EBZ4800

EBZ5100/

EBZ5100RH/

EBZ5150/

EBZ5150RH

EBZ5100Q/

EBZ5150Q EB6200 EB7000 EB7001

EBZ7100/

EBZ7100RH/

EBZ7150/

EBZ7150RH/

EBZ8001/

EBZ8001RH/

EBZ8050/

EBZ8050RH

JAP, EU, General EU, General

Sales Region

(Reference) EU, General JAP EU, General USA USA JAP, General JAP, EU, General USA USA General EU, General JAP USA USA

Remarks

Cycle － 2 ← ← ← 2 ← ← ← ← ← ← ← ← ←

Number of Cylinders － 1 ← ← ← 1 ← ← ← ← ← ← ← ← ←

Valve Type － Piston valve ← ← ← ← ← ← ← ← ← ← ← ← ←

Cylinder Bore mm (in.) 32 (1.260) ← 34 (1.339) ← 38 (1.496) 40 (1.575) 43 (1.693) 44 (1.732) ← 47.5 (1.870) ← ← ← 50 (1.969)

Stroke mm (in.) 28 (1.102) ← ← ← 26 (1.024) 33 (1.299) ← ← ← 35 (1.378) ← ← 36.6 (1.441) ←

Displacement cm3 22.5 ← 25.4 ← 29.5 41.5 47.9 50.2 ← 62 ← ← 64.9 71.9

Effective

Compression Ratio － 7.7 ← 8 7.4 7.4 8.1 8 7.8 7.3 7.7 ← ← 7.4 7.5

Fuel － Gasoline/oil mixed fuel ← ← ← ← ← ← ← ← ← ← ← ← ←

Engine lubrication － Fuel-oil mixture ← ← ← ← ← ← ← ← ← ← ← ← ←

Engine lubrication Oil － 2-cycle oil ← ← ← ← ← ← ← ← ← ← ← ← ←

Mixing Ratio －

Zenoah FC 40:1

Normal FB 25:1

RedMax FD 50:1

← ← ← ← ← ← ← ← ← ← ← ← ←

Type － Diaphragm type

rotary valve ← ← ← ← ← ← ← ← ← ← ← ← ←

Carburetor

(Walbro) Model － WYJ-110A WYJ-374 WYA-26E WYA-65 USA, EU: WYA-73B

JAP: WYA-82 WYK-67A EU：WYA-51B

JAP：WYA-42B WYA-79 WYA-83 WYK-73A WYK-123A ← WYA-81 WYA-44B

Starting Method － Recoil starter

Recoil starter

(Coil dumper type: EZ) Recoil starter ← Recoil starter

(Coil dumper type: EZ) Recoil starter ← ← ← ← ← ← ← ←

Type －

Analog controlled

TCI Flywheel

Magneto with

advance-angle

←

Analog controlled

CDI Flywheel

Magneto with

advance-angle

← ← ← ←

Digital controlled

CDI Flywheel

Magneto with

advance-angle

Analog controlled

CDI Flywheel

Magneto with

advance-angle

← ← ←

Digital controlled

CDI Flywheel

Magneto with

advance-angle

←

Digital control Misfire

for excessive speed

Maximum speed:

85000 rpm

Ignition

System

Model － UK-08922-01 ← UK-08922-35 ← USA: UK-08958C-31

JAP, EU: UK-08958-31 ZMG-8 ZMG-10G UK-08963-54 ZMG-10G ZMG-8 ← ← ZMG-14CGD ZMG-14GD

Ignition Timing °/ rpm 24/ 6000 ← 35/ 7000 ← 37/ 7500 28/ 7000 35/ 7000 33/ 7000 35/ 7000 28/ 7000 ← ← 34/ 7000 33/ 7000

Type － RCJ6Y ← CMR7A CMR7H ← RJ6C CMR7H ← ← BPMR7A ← ← CMR7H ←

Spark Plug Gap mm (in.) 0.6～0.7

(0.024～0.028) ← ← ← ← ← ← ← ← ← ← ← ← ←

Type － Primary coil

short-circuiting ← ← ← ← ← ← ← ← ← ← ← ← ←

LH － No setting Push type No setting Push type Toggle type No setting ← Push type ← ←

Stopping

Method Switch RH － Push type ← ← ← Slide type ← ← ← ← ← ← No setting Slide type ←

Cooling System － Forced air cooling ← ← ← ← ← ← ← ← ← ← ← ← ←

Air Cleaner

Element Type － Single layer dry

element ← ← ← ← Single layer

half-wet element

Dual layer

half-wet element

Single layer

half-wet element ← ← Primary: Dry puff

Secondary: Dry paper ← ← ←

Output Axle Rotation

Direction － Counterclockwise ← ← ← ← ← ← ← ← ← ← ← ← ← View from output

axle

Length mm (in.) 325 (12.8) ← 327 (12.9) ← 313 (12.3) 335 (13.2) 352 (13.9) 401 (15.8) ← 336 (13.2) ← 365 (14.4) 371 (14.6)

380 (15.0)/

USA: 390 (15.4)

Width mm (in.) 225 (8.86) 233 (9.17) 268 (10.55) 269 (10.59) 394 (15.5) ★489 (19.3)

/ 454 (17.9) 452 (17.8) ★483 (19.0)

/ 441 (17.4) ★483 (19.0) ★489 (19.3)

/ 454 (17.9) 449 (17.7) ★485 (19.1) ★487 (19.2)

/ 467 (18.4)

★540 (21.3)

/ 490 (19.3)

Throttle arm

Vertical state

Overall

Dimensions

Height mm (in.) 360 (14.2) ← ← ← 420 (16.5) 495 (19.5) 476 (18.7) 495 (19.5) ← ← ← ← ← 496 (19.5)

Dry Weight kg (lbs.) 3.7 (8.16) ← 3.9 (8.6) 4 (8.82) 6.1 8.5 8.9 9.4 ← 9.1 9.7 ← 10.6 11.7/ USA：11.5 Elbow included,

Blower pipe excluded

Fuel Tank Capacity L 0.75 ← 0.65 ← 1.08 1.8 1.9 2.1 ← 2 2.1 ← ← 2.3

Idling Speed rpm 2300 ← 2800 3000 3000 2000 2300 2200 ← 2000 ← ← ← ←

Operating Speed rpm 7500 ← 7890 7600 6700 6350 6250 6000 5700 7700 7300 ← 7050 6700

Blower Nozzle

Diameter mm (in.) 66 (2.60) ← ← ← ← ← 66 (2.60)

Option: 55 (2.17) 66 (2.60) ← ← ← ← ← 72 (2.835)

Average air volume at

aimed blowing point m3/ min 10 ← 10.4 ← 10.6 12 13.2 13.8 12.8 14 15 16.5 16.6 19.4

Maximum air speed at

aimed blowing point

(Calculated estimate)

m/ s 55.4 ← ← ← 58.7 66.5 73.1 76.4 70.9 77.5 83.1 91.4 91.9 90.3

Maximum Output kW/ rpm

(PS)

0.86/ 8000

(1.17)

←

←

0.88/ 7500

(1.2)

0.86/ 7500

(1.17)

0.95/ 7500

(1.29)

1.80/ 8000

(2.45)

1.88/ 8000

(2.56)

1.62/ 7500

(2.2)

1.53/ 7500

(2.08)

2.87/ 7500

(3.9)

3.1/ 7000

(4.1)

3.1/ 7000

(4.1)

2.98/ 8000

(4.05)

3.29/ 8000

(4.48)

Fuel Consumption L/ h 0.8 ← 0.59 0.51 0.59 1.7 1.05 1.1 0.98 1.9 ← ← 1.65 1.85 Under actual blower

state

Ambient noise at

15 m from the blower dB (A) 70 ← 69 72 69 74 67 71 68 75 ← ← 77 77 ANSI B175.2-2000

Noise at operator

(Reference value) dB (A) 91 ← 95 92 91 99 92 94 92 97 99 ← 100 100

Sound Power Level dB (A) 106 ← 106 ← 100 106 104 104 102 110 107 ← 110 112 ISO 11094

3

2. Specifications and Technical Data

2-2 Pipe Unit: mm (in.)

Part Name Grip Assembly Vacuum Kit Pipe End Straight Pipe＋

＋＋

＋Duckbill Nozzle

Form

Standard D=φ60 (2.36) D=φ74 (2.91) D=φ80 (3.15) φ73 (2.87)×φ66 (2.60) φ73 (2.87)×φ57 (2.24) φ79 (3.11)×φ66 (2.60) φ79 (3.11)×φ72 (2.84) Forφ73 (2.87) Forφ79 (3.11)

RedMax Lodo 6811-51220 (Standard) 2756-51220 (Option) 848-L5C-65E1 (Standard) 848-L58-65E1 (Standard)

Part

Number Solid Color

3495-51400

(Option)

2750-51501

(Standard)

848-L58-6521

(Standard)

-

(Option)

848-L0L-65E0 (Standard) 848-L38-65E0 (Option) 848-L5K-65E1 (Standard) 848-L5Z-65E0 (Standard)

6811-51211+6811-51230

(Option)

848-L58-65D0+848-L58-65L0

(Option)

EB430/

EBE440 ● ●

+(2750-51200 Swivel Joint)

HB2302/

HB2311EZ/

HBZ2601

-

-

-

● ● ● (Option) ●

EBZ3000

-

-

-

● ● (Option) ●

EB4300/

EB6200/

EB7000

● ● ● (Option) ●

EBZ4800 ● ● ● (Standard) ●

EBZ5100Q ● ● ● (Option) ●

EBZ5100/

EB7001 ● ● ● (Option) ●

EBZ7100 ● ● (Standard) ● (Option) ●

Model

EBZ8001 ● ● (Option) ● (Standard) ●

Part Name Flexible Pipe Swivel Joint Straight Pipe Silencer Pipe End

Form

Diameter: D φ87 (3.43) φ87 (3.43) φ94 (3.70) φ99.5 (3.92) φ70 (2.76) φ70 (2.76) φ80 (3.15) φ61 (2.40) φ74 (2.91) φ80 (3.15) φ74 (2.91) φ61 (2.40) φ73 (2.84) φ73 (2.87) φ79 (3.11) φ79 (3.11)

Diameter: D1 φ70 (2.76) φ70 (2.76) φ70 (2.76) φ80.5 (3.17) φ60 (2.36) φ74 (2.91) φ79 (3.11) φ60 (2.36) φ73 (2.87) φ79 (3.11) φ73 (2.87) φ57 (2.24) φ66 (2.60) φ57 (2.24) φ66 (2.60) φ72 (2.84)

Standard

Length: L 420 (16.54) 372 (14.65) 345 (13.58) 345 (13.58) 370 (14.57) 340 (13.39) 365 (14.37) 370 (14.54) 320 (12.60) 365 (14.37) 346 (13.62) 355 (13.98) 340 (13.39) 340 (13.39) 340 (13.39) 340 (13.39)

RedMax Lodo

-

6811-51220 2756-51220 848-L5C-65E1 848-L58-65E1

Part

Number Solid Color 3495-51110 T4017-51110 T4030-51110 848-L65-65A0 3495-51202 2750-51201 848-L58-6511 3495-51321 6811-51211 848-L58-65D0 T4030-51110 3495-51300 848-L0L-65E0 848-L38-65E0 848-L5K-65E1 848-L5Z-65E0

EB430/

EBE440 ● ● ●

-

●

HB2302/

HB2311EZ/

HBZ2601

-

-

-

-

-

-

-

●

-

●

EBZ3000 ● ● ●

-

●

EB4300/

EB6200/

EB7000

● ● ●

-

●

EBZ4800 ● ●

-

-

-

● ● ●

EBZ5100Q ● ●

-

-

-

● ●

EBZ5100/

EB7001 ● ● ●

-

●

EBZ7100 ● ● ●

-

●

Model

EBZ8001 ● ● ●

-

●

Diameter: D

φ66

(2.60)

φ57

(2.24)

φ66

(2.60)

φ72

(2.84)

23 (0.91)

138 (5.43)

D

D1

L D

D1

L D

D1

L D

D1

L D

D1

L

30 (1.18)

180 (7.19)

4

2. Specifications and Technical Data

2-3 Overall dimensions

Handheld Blower

Backpack Blower

Unit: mm (in.)

Blower Type A B C D

HB2302 325 (12.8) 225 (8.86) 360 (14.2) 610 (24.0)

HB2311EZ 325 (12.8) 233 (9.17) 360 (14.2) 610 (24.0)

HBZ2601 268 (10.55)

HBZ2601 (USA) 327 (12.9) 269 (10.59) 360 (14.2) 610 (24.0)

Unit: mm (in.)

Blower Type A B BB C D

EBZ3000/ 3000RH/ 3050/ 3050RH 313

(12.3) ― 394

(15.5)

420

(16.5)

1222

(48.11)

EB4300 335

(13.2)

489

(19.3)

454

(17.9)

495

(19.5)

1222

(48.11)

EBZ4800 352

(13.9) ― 452

(17.8)

476

(18.7)

1248

(49.13)

EBZ5100/ 5100RH/ 5150/ 5150RH 401

(15.8)

483

(19.0)

441

(17.4)

495

(19.5)

1195

(47.05)

EBZ5100Q/ 5150Q 401

(15.8)

483

(19.0) ― 495

(19.5)

1221

(48.07)

EB6200 336

(13.2)

489

(19.3)

454

(17.9)

495

(19.5)

1222

(48.11)

EB7000 336

(13.2) ― 449

(17.7)

495

(19.5)

1222

(48.11)

EB7001 365

(14.4)

485

(19.1) ― 495

(19.5)

1195

(47.05)

EBZ7100/ 7100RH/ 7150/ 7150RH 371

(14.6)

487

(19.2)

467

(18.4)

495

(19.5)

1185

(46.65)

EBZ8001 380

(15.0)

EBZ8001/ 8001RH/ 8050/ 8050RH:

USA

390

(15.4)

540

(21.3)

490

(19.3)

496

(19.5)

1185

(46.65)

RH: Right hand throttle lever specification

5

3. Special Tools

3-1 Rotor Removal

Description

Part Name

Part Number

Model

Stopper

2670-96220

1664-96410

Stopper

3350-96220

Stopper

4810-96220

Puller Assy

2890-96100

Puller Assy

1490-96101

Puller Assy

2750-96100

Wrench (HEX)

3304-97611

Size: 3/4/5 mm

Wrench (TORX)

2850-96410

Size: T20/ T25/ T27

HB23 Series ● ● ●

HBZ26 Series ● ●

EBZ30 Series ● ● ●

EB4300/ 6200

EB70 Series ● ● ●

EBZ4800

EB51/ 71/ 80 Series ● ● ●

Remove the rotor using the puller assy (special tool) while preventing piston movement by setting the stopper

(special tool).

Examples of special tool usage and maintenance procedures categorized by type and series are explained

below. Each drawing includes information on parts such as mount screws and disassembly cautions.

How to use (Procedure) Handheld Blower: HB23 Series, HBZ26 Series

1. Remove the plug, and detach the main complete

parts. Remove the carburetor, recoil starter and

fuel tank if necessary.

【

【【

【Disassembly Flowchart】

】】

】

Volute Cover Assy.

↓

Engine Cover

↓

Below the procedure

Volute Cover Assy.

Mounting Screw (5)

【

【【

【HB23 Series】

】】

】:

(+): P5×L20

【

【【

【HBZ26 Series】

】】

】:

TORX (T27): P5×L20

Mounting Screw (7)

(+): P5×L20

Mounting Screw (7)

TORX (T27): P5×L20

【

【【

【HB23 Series】

】】

】

Mounting Screw (1)

(+): M4×L14 (PW)

Mounting Screw (2)

TORX (T27): M5×L16

＊Installing with the recoil starter.

Engine Cover

Engine Cover

Engine Short Block

Volute Case

【

【【

【HBZ26 Series】

】】

】

Construction

6

3. SPECIAL TOOLS

Handheld Blower: HB23 Series, HBZ26 Series

2. Set the stopper (special tool) into the plug hole.

3. Remove the mounting nut using the box wrench

then remove the fan.

4. Remove the extension using the wrench.

5. Remove the four mounting screws, separate the

volute case and the engine short block.

Stopper

【

【【

【HB23 Series】

】】

】 【

【【

【HBZ26 Series】

】】

】

Stopper

Box Wrench

(12 mm)

Mounting Nut

(12 mm Hex)

Washer

Washer

Fan

Extension

Wrench (17 mm)

Mounting Screw

【

【【

【HB23 Series】

】】

】:

(+): M5×L14 (PW, SW)

【

【【

【HBZ26 Series】

】】

】:

TORX (T27): M5×L14

Engine Short Block

Volute Case

7

3. Special Tools

Handheld Blower: HB23 Series, HBZ26 Series

6. Remove the rotor using the puller assy.

Apply 8 mm puller bolts.

How to use (Procedure) Backpack Blower: EBZ30 Series

1. Remove the plug, and detach the main complete

parts. Remove the carburetor, recoil starter and

fuel tank if necessary.

Rotor

Puller Assy

Puller Bolt (8 mm) 17 mm

【

【【

【Disassembly Flowchart】

】】

】

Air Inlet Net

↓

Spring Damper

↓

Frame

↓

Volute Cover Assy

↓

Engine Cover

↓

Below the procedure

Volute Cover Assy.

Mounting Screw (8)

TORX (T27): M5×L25

Mounting Screw (3)

Mounting Bolt (1)

(+): M5×L16

Mounting Screw (3)

TORX (T27): M5×25

Engine Cover

Engine Short Block

Volute Case

Air Inlet Net

Plate

Clip (4)

Frame

Mounting Nut (2)

M6

Mounting Screw (2)

TORX (T27/ P): M5×L70

Mounting Nut (2)

M5

Lower Damper

Refer to

“4-2 Air Inlet Net Removal”

Refer to

“4-3 Upper Spring Damper Removal”

Refer to

“4-4 Volute Cover Lower Damper Removal”

Construction

8

3. SPECIAL TOOLS

Backpack Blower: EBZ30 Series

2. Set the stopper (special tool) into the plug hole.

3. Remove the four mounting screws, then remove

the fan.

4. Remove the four mounting screws, separate the

volute case and the engine short block.

Stopper

Fan

Mounting Bolt

TORX (T27): M6×L30

Mounting Bolt

TORX (T27):

M5×L20

Engine Short Block

Volute Case

9

3. Special Tools

Backpack Blower: EBZ30 Series

5. Remove the mounting nut using the box wrench.

6. Remove the rotor using the puller assy.

Apply 8 mm puller bolts.

How to use (Procedure) Backpack Blower: EB4300/ 6200, EB70 Series, EBZ4800, EBZ51/ 71/ 80 Series

1. Remove the plug, and detach the main complete

parts. Remove the carburetor, recoil starter and

fuel tank if necessary.

【

【【

【Disassembly Flowchart】

】】

】

Air Inlet Net

↓

Frame

↓

Engine Cover

↓

Below the procedure

Rotor

Puller Assy.

Puller Bolt (8 mm)

Box Wrench

(12 mm)

Mounting Nut

(12 mm Hex)

Volute Cover Assy.

Mounting Screw (1)

Engine Cover

Engine Short Block

Volute Case

Lower Damper

A

ir Inlet Net

Upper Dumper

Clip (4)

Frame

Mounting Nut (2)

M6

Mounting Screw (4)

Refer to

“4-2 Air Inlet Net Removal”

Refer to

“4-4 Volute Cover Lower Damper Removal”

Refer to

“4-20 Upper Damper Assembly”

Exceptions for

EB4300/ 6200

Construction

10

3. SPECIAL TOOLS

Backpack Blower: EB4300/ 6200, EB70 Series, EBZ4800, EBZ51/ 71/ 80 Series

2. Set the stopper (special tool) into the plug hole.

3. Remove the four mount screws, then remove the

fan. The fan is detached but stays inside the volute

cover assembly and the volute case.

4. Remove the six mounting screws then remove the

engine short block from the volute case.

5. Remove the mounting nut using the box wrench.

6. Remove the rotor using the puller assy.

Rotor

Puller Assy.

Box Wrench

(12 mm)

Mounting Nut

(12 mm Hex)

Stopper

Fan

Mounting

Bolt

Volute Cover Assy.

Volute

Case

Mounting Bolt

Engine Short Block

Volute Case

11

3. Special Tools

3-2 Module Assembly

Description

Part Name

Part Number

Model

Gauge

3350-96240

T=0.4 mm

Gauge

2750-96240

t=0.3 mm

Gauge

848-8W4-0050

t=0.4 mm

Wrench (HEX) 3304-97611

Size: 3/ 4/ 5 mm

Wrench (TORX) 2850-96410

Size: T20/ T25/ T27

HB23 Series

HBZ26 Series

EBZ30 Series

● ●

EB4300/ 6200

EB70 Series

EBZ4800/ 5100Q

● ●

EBZ5100

EBZ71/ 80 Series ● ●

Adjust the air gap between the rotor's magnetic steel and the module using the gauge (special tool).

Module Resistance

Model Engine Type Primary Side

(Iron Core ⇒Primary Lead)

Secondary Side

(Iron Core ⇒High Tension Lead)

Air Gap

mm (in.)

HB2302/ 2311EZ G23L 0.8 kΩ 4.23 kΩ 0.3～0.4 (0.012～0.016)

HBZ2601 GZ25N ＋Side 8.45 kΩ －Side 2.70 kΩ 2.92 kΩ 0.3～0.4 (0.012～0.016)

EBZ3000 GZ30N ＋Side 30.3 kΩ －Side 37.2 kΩ 2.04 kΩ 0.3～0.4 (0.012～0.016)

EBZ3000RH/ 3050RH GZ30N （USA） ＋Side 31.6 kΩ －Side 37.4 kΩ 2.05 kΩ 0.3～0.4 (0.012～0.016)

EB4300 G4K 0.17 kΩ 1.4 kΩ 0.3～0.4 (0.012～0.016)

EBZ4800 GZ48N

EBZ5100Q/ 5150Q GZ51N

0.33 kΩ 2.77 kΩ 0.3～0.4 (0.012～0.016)

EBZ5100/ 5100RH

EBZ5150/ 5150RH GZ51N ＋Side 71.2 kΩ

－Side: cannot be measured 11.0 kΩ 0.35～0.45 (0.014～0.018)

EB6200/ 7000/ 7001 G62L 0.17 kΩ 1.4 kΩ 0.3～0.4 (0.012～0.016)

EBZ7100/ 7100RH

EBZ7150/ 7150RH GZ65N Several MΩ or higher 2.74 kΩ 0.35～0.45 (0.014～0.018)

EBZ8001/ 8001RH

EBZ8050/ 8050RH GZ72N Several MΩ or higher 2.72 kΩ 0.35～0.45 (0.014～0.018)

The resistance values shown above are the

reference values for resistance tester

measurement. The resistance value is within

the normal range shows no internal leakage

or any other defect.

We supply the measurement equipment (gap

tester) that can measure spark energy while

the engine is running.

3699-90247

Three-point gap tester

* Connect Negative Side (black) to Iron Core.

REFERENCE

12

3. SPECIAL TOOLS

Examples of the gauge (special tool) usages are shown according to the type of the gauge.

Gauge: 3350-96240 (T=0.4 mm) HB23 Series, HBZ26 Series, EBZ30 Series

1. Remove the obstructive parts in order to see the

rotor and the module.

(Refer to “3-1 Rotor Removal”.)

2. Insert a gauge (special tool) between the rotor

magnet metal and module. Tighten the mounting

bolts while pushing the module against the rotor.

【

【【

【HB23 Series】

】】

】

Module

Rotor Wrench

Gauge

Mounting Bolt

【

【【

【HBZ26 Series】

】】

】

Module

Rotor Wrench

Gauge

Mounting Bolt

【

【【

【EBZ30 Series】

】】

】

Module

Rotor

Wrench

Gauge

Mounting Bolt

13

3. Special Tools

Gauge: 2750-96240 (T=0.3 mm) EB4300/ 6200, EB70 Series, EBZ4800/ 5100Q

1. Remove the module cover.

2. Insert a gauge (special tool) between the rotor

magnet metal and module. Tighten the mounting

bolts while pushing the module against the rotor.

Gauge: 848-8W4-0050 (T=0.4 mm) EBZ5100, EBZ71/ 80 Series

1. Remove the module cover.

2. Insert a gauge (special tool) between the rotor

magnet metal and module. Tighten the mounting

bolts while pushing the module against the rotor.

Module

Rotor

Wrench

Gauge

Mounting Bolt

【

【【

【EB4300/ 6200, EB70 Series】

】】

】

【

【【

【EBZ4800/ 5100Q】

】】

】

Module

Rotor

Wrench

Gauge

Mounting Bolt

【

【【

【EBZ5100】

】】

】

Module

Rotor Wrench

Gauge

Mounting Bolt

【

【【

【EBZ71/ 80 Series】

】】

】

Module

Rotor Wrench

Gauge

Mounting Bolt

14

3. SPECIAL TOOLS

3-3 Recoil Pulley Removal

Description

Part Name

Part Number

Model

Stopper

4810-96220

Puller

4500-96100

Puller

848-8W0-0020

Wrench (HEX) 3304-97611

Size: 3/ 4/ 5 mm

Wrench (TORX) 2850-96410

Size: T20/ T25/ T27

HBZ26 Series ● ● ●

EBZ71/ 80 Series ● ● ●

Remove the recoil pulley using the puller (special tool) while preventing piston movement by setting the

stopper (special tool).

Examples of the puller (special tool) usages are shown according to the type of the puller.

Puller: 4500-96100 HBZ26 Series

1. Remove the recoil starter and the spark plug.

2. Insert the stopper (special tool) to the plug hole

(Refer to “3-1 Rotor Removal”).

3. Engage the puller (special tool) to 2 holes on the

pulley and pull out the pulley.

Note: Pulley screw is right turn screw.

Puller: 848-8W0-0020 EBZ71/ 80 Series

1. Remove the recoil starter and the spark plug.

2. Insert the stopper (special tool) to the plug hole

(Refer to “3-1 Rotor Removal”).

3. Extract the pulley while holding the pulley by the

puller's pins (special tool).

Note: Pulley screw is right turn screw.

Puller

Box Wrench

Pulley

Pin

Hole

Puller

Box Wrench

Pulley

Puller

Pulley

Pin

Pin

Pin

Pin

15

3. Special Tools

3-4 Piston Pin Removal

Description

Part Name

Part Number

Model

Rod Assy

1101-96220

φ7.5×φ4.7

Rod Assy

3350-96230

φ11×φ8

Rod Assy

2750-96230

φ11×35 mm

Wrench (HEX) 3304-97611

Size: 3/ 4/ 5 mm

Wrench (TORX) 2850-96410

Size: T20/ T25/ T27

HB23 Series

HBZ26 Series ● ●

EBZ30 Series

EB4300 ● ●

EB6200

EB70 Series

● ●

EBZ4800

EBZ51 Series ● ●

EBZ71/ 80 Series ●(Only a rod is used.) ●

Remove the cylinder, and then the piston pin using the rod assy (special tool).

Examples of the rod assy (special tool) usages are shown according to the type of the rod assy.

Rod Assy: 1101-96220 HB23 Series, HBZ26 Series

1. Remove the engine short block (refer to “3-1 Rotor

Removal”) and then remove the cylinder.

2. Remove the snap rings from both sides of the

piston pin.

3. Engage the rod assy (special tool) against the

piston pin and gently tap with a plastic hammer to

push out the pin.

Hard hammering may damage the big end of

the connecting rod.

EBZ71/ 80 Series are designed so that the

piston assembly can be disassembled

without any tool. However, if it is difficult to

pull out the piston pin, use the special tool

(Rod Assy: 1101-96220) to push out the

piston pin.

Rod Assy.

Plastic Hammer

Piston

CAUTION

Rod

Piston Pin

Piston REFERENCE

16

3. SPECIAL TOOLS

Rod Assy: 3350-96230 EBZ30 Series, EB4300, EBZ4800, EBZ51 Series

1. Remove the engine short block (refer to “3-1 Rotor

Removal”) and then remove the cylinder.

2. Remove the snap rings from both sides of the

piston pin.

3. Insertion the rod assy (special tool) against the

piston pin and gently tap with a plastic hammer to

push out the pin.

Hard hammering may damage the big end of

the connecting rod.

Rod Assy: 2750-96230 EB6200, EB70 Series

1. Remove the engine short block (refer to “3-1 Rotor

Removal”) and then remove the cylinder.

2. Remove the snap ring from starter side of the

piston pin.

3. Rest the rod assembly against the end of the piston

pin and pull the piston pin out from the piston.

CAUTION

Rod assy.

Piston Pin

Piston

Rod Assy.

Piston Pin

Piston

Piston Pin

Snap Ring

(Don’t remove)

Snap Ring

(Remove)

Snap Ring

Rod Assy.

17

4. Service Guide

4-1 Starter Pulley Removal

HB23 Series, EBZ30 Series

● Insert the stopper (special tool) into the plug hole

(refer to “3 Special Tool”) to secure the piston.

● Remove the starter pulley using commercially

available pliers. The pulley must be covered with

cloth to prevent from damage.

Never remove the starter pulley by hitting

with a hammer.

Doing so may damage the pulley.

EB4300/ 6200, EB70 Series, EBZ4800, EBZ51 Series

● Insert the stopper (special tool) into the plug hole

(refer to “3 Special Tool”) to secure the piston.

● Remove nut (M10), set a commercially available

puller, then remove the starter pulley.

Never remove the starter pulley by hitting

with a hammer.

Doing so may damage the pulley.

4-2 Air Inlet Net Removal

EB6200, EB70 Series, EBZ4800, EBZ30/ 51/ 71/ 80 Series

The air inlet net is mounted by four clips.

The removal procedure is shown below.

1. Loosen each clip’s resin screw and remove the

whole.

Set the Philips screwdriver against the resin

screw securely. Insufficient or excessive

contact may cause the resin head to break.

2. Insert a screwdriver between free flow net and

frame, then wrench the clip open by twisting the

screwdriver.

Pay attention not to damage the air inlet net

or frame with the screwdriver.

CAUTION

CAUTION

Pliers

Cloth

Starter Pulley

Box Wrench

Nut (M10)

Starter Pulley

Puller

Starter Pulley

CAUTION

CAUTION

Resin Screw

【

【【

【Clip Position】

】】

】

Clip

A

ir Inlet Net

Screwdriver

18

4. Service Guide

4-3 Upper Spring Damper Removal

EBZ30 Series

To remove the upper spring damper, follow the

procedure below.

1. Remove the three mounting screws.

2. Pull the plate upward from the spring holder’s

groove.

3. Press the upper part of the volute to the frame to

slacken the strap, and then pull out the plate.

4. Pull the strap out from the volute case.

5. Remove the spring from the volute case, then the

spring holder. The spring is easily removed by

pressing and turning the tip of the spring along the

spring groove with a screwdriver.

Mounting Screw

TORX (T27): M5×L25

Spring Holder

Plate

Strap Plate

Strap

Volute Case

Spring Holder

Spring

Spring

Screwdriver

Screwdriver

19

4. Service Guide

4-4 Volute Cover Lower Damper Removal

EB6200, EB70 Series, EBZ4800, EBZ30/ 51/ 71 Series

● Remove the volute unit from the frame.

● Remove the all mount mounting screws, separate

volute cover from its case, then remove the lower

damper unit.

EBZ80 Series

● Remove the volute unit from the frame.

● Remove the cover by removing the three mounting

screws then remove the lower damper from the

volute case’s groove.

4-5 Flywheel Side Crankshaft Removal

EBZ4800, EBZ30/ 51/ 71/ 80 Series

● Be sure to extract the key beforehand.

● The precision fit between crankshaft and main

bearings is very tight. Be sure to use the press to

remove the crankshaft.

Never hit the crankshaft to remove it.

The crankshaft’s threading may be lost or the

shaft axis may deform.

● Secure the crankcase on support and then press

the crankshaft with the press via the guide.

Never press the crankshaft directly with the

press.

Doing so may damage the shaft’s threading.

CAUTION

CAUTION

Lower Damper

Volute Unit

Cover

Mounting Screw

Key

Press

Crankshaft

Support

Guide

Mounting Screw

Lower Damper

Volute Cover

Volute Case

20

4. Service Guide

4-6 Crankcase Oil Seal and Bearings Removal

All Models

● Disassembly is usually unnecessary. However, if

the oil seal’s main lip or dust lip is worn, the shaft

will become loose due to bearing wear or if the they

have seized, replace the oil seal and bearings with

new ones.

● Be sure to use the press to remove the bearings.

Be sure to use the press to press the

bearings out during bearing removal. Without

jig use to the crankcase may be damaged.

● If the crankcase’s bearings are worn, replace them

with new ones.

CAUTION

Bearing

Support

Bearing Guide

【

【【

【Fan Side】

】】

】

Crankcase

Bearing

Support

Bearing Guide

【

【【

【Starter Side】

】】

】

Crankcase

Press

Press

21

4. Service Guide

4-7 Crankcase Assembling

Bearings, snap ring, oil seal configuration and installation position differ depending on type.

Properly install each part and reassemble the crankcase referring to the corresponding type’s drawing.

For bearing and oil seal installation, refer to the explanation on page 23.

HB23 Series, HBZ26 Series

EBZ30 Series

EB4300

【

【【

【Fan Side】

】】

】

Push the oil seal within 0 to

0.5 mm (0.02 in.) from the

crankcase surface.

Oil Seal

【

【【

【Starter Side】

】】

】

Oil Seal

Align the oil seal surface with

the crankcase surface.

Bearing

Push the bearings until they

contact the snap ring.

Bearing

Push the bearings until they

contact the crankcase.

Snap Ring

Crank Case

Construction

Push the oil seal within 0 to

0.5 mm (0.02 in.) from the

crankcase surface.

Oil Seal

【

【【

【Fan Side】

】】

】 【

【【

【Starter Side】

】】

】

Bearing

Push the bearings until they

contact the crankcase.

Snap Ring

Do not cover the lubrication

hole with the snap ring.

Lubrication Hole

Snap Ring

Push the oil seal within 3.3

to 3.8 mm (0.13 to 0.15 in.)

from the crankcase surface.

Oil Seal

Bearing

Push the bearings until they

contact the snap ring.

Lubrication Hole

Crank Case

Construction

【

【【

【Fan Side】

】】

】

Push the oil seal

until its surface

comes trim with

the crankcase

edge surface.

Oil Seal

【

【【

【Starter Side】

】】

】

Push the oil seal until

its surface comes trim

with the crankcase

edge surface.

Bearing

Push the bearings until they

contact the snap ring.

Bearing

Push the bearings until they

contact the crankcase.

Snap Ring

Oil Seal

Crank Case

Construction

22

4. Service Guide

EBZ4800, EBZ51 Series

EB6200, EB70 Series, EBZ71/ 80 Series

Snap Ring Assembly EB6200, EB70 Series, EBZ4800, EBZ30/ 51/ 71/ 80 Series

A lubrication hole exists to increase lubrication to the

main bearing. Do not cover the hole with the snap ring.

Set the snap ring’s gap to the piston side.

Lubrication Hole

Sna

p

Rin

g

【

【【

【piston Side】

】】

】

Push the oil

seal within 0 to

0.5 mm (0.02

in.) from the

crankcase

surface.

Oil Seal

【

【【

【Fan Side】

】】

】 【

【【

【Starter Side】

】】

】

Bearing

Push the bearings until they

contact the crankcase.

Snap Ring

Do not cover the

lubrication hole with the

snap ring.

Lubrication Hole

Push the oil seal

within 1.5 to 2.3 mm

(0.06 to 0.09 in.)

from the crankcase

surface.

Oil Seal

Bearing

Push the bearings until they

contact the snap ring.

Lubrication Hole

Crank Case

Construction

Push the oil seal

within 1.3 to 1.7

mm (0.05 to

0.07 in.) from

the crankcase

surface.

Oil Seal

【

【【

【Fan Side】

】】

】 【

【【

【Starter Side】

】】

】

Bearing

Push the bearings until they

contact the crankcase.

Snap Ring

Do not cover the

lubrication hole with the

snap ring.

Lubrication Hole

Push the oil seal

within 5.3 to 5.7

mm (0.21 to 0.22

in.) from the

crankcase

surface.

Oil Seal

Bearing

Push the bearings until they

contact the snap ring.

Lubrication Hole

Crank Case

Snap Ring

Construction

23

4. Service Guide

Oil Seal Assembly All Models

● Never insert the oil seal obliquely. The oil seal may

be fall out.

● Before the oil seal is pressure-inserted, apply

grease to the oil seal.

● Press the oil seal from the outside of the crankcase

using combined special tools (holder and guide).

● Pay attention because oil seal pressure-insertion

position differs according to rotor, starter and

engine type.

For the insertion position of particular models, refer

to “4-7 Crankcase Assembly”.

Bearing Assembly All Models

● Never insert the oil seal obliquely. Press it securely

until it contacts the snap ring.

● Before the bearing is pressure-inserted, apply

grease to the bearing.

● Face the bearing identification mark (mark is

recessed) toward the inside of the crankcase and

then insert it.

● Press the bearings from the outside of the

crankcase using combined special tools (holder

and guide).

Crankcase Assembly EB6200, EB70 Series, EBZ4800, EBZ30/ 51/ 71/ 80 Series

● The precision fit between crankshaft and main

bearing is very tight. Be sure to use an insertion jig

to remove the crankshaft.

Never hit the crankshaft by hammer or

equivalent. The shaft’s threading may be lost

or the shaft axis may deform.

● Secure the crankcase on support and then press

the crankshaft with the press via the guide.

Never press the crankshaft directly with the

press.

Doing so may damage the shaft’s threading.

CAUTION

CAUTION

Press

Guide

Crankshaft

Oil Seal

Support

【

【【

【Crankcase Outside】

】】

】

Press

Ball Bearing

Snap Ring

【

【【

【Crankcase Inside】

】】

】

Support

Press

24

4. Service Guide

4-8 Piston Inserting Direction

All Models

Make sure to point the recessed mark (arrow or

triangle) on the piston head to the exhaust (muffler)

side.

4-9 Piston Pin Snap Ring Assembly

End Gap Position HB23 Series, HBZ26 Series, EB4300/ 6200, EB70 Series

Fit the snap ring in the piston’s groove firmly and position

the end gap of the snap ring below the piston.

・

・・

・ If the snap ring is poorly inserted or the end

gap of the snap ring is incorrectly

positioned, the snap ring may comes off

during engine operation resulting in

damage to the engine.

・

・・

・ Never reuse a snap ring. Always insert a

new one.

End Gap Position EBZ4800, EBZ30/ 51/ 71/ 80 Series

Fit the snap ring in the groove firmly and position the end

gap of the snap ring opposite the notch.

・

・・

・ If the snap ring is poorly inserted or the end

gap of the snap ring is incorrectly

positioned, the snap ring may comes off

during engine operation resulting in

damage to the engine.

・

・・

・ Never reuse a snap ring. Always insert a

new one.

Check After Installation All Models

After the snap ring is installed, check that it fits firmly

in the correct direction.

Turn the snap ring using thin tipped tool and

check that it moves smoothly in its groove.

If the snap ring is improperly installed, it will

not move smoothly in its groove.

CAUTION

CAUTION

Notch

End Gap

Snap Ring

Notch

End Gap

Snap Ring

Piston Pin

Groove

Snap Ring

Snap Ring

REFERENCE

【

【【

【Exhaust Side】

】】

】

Triangle Mark Arrow Mark

【

【【

【Exhaust Side】

】】

】

25

4. Service Guide

4-10 Positioning of Lead Air Intake Tube

HBZ26 Series

The lead air intake tube has cast marking of either “F”

or “S”.

“S” is for the starter end, and “F” for the fan end.

Assembling position shall not be mixed up.

Caution: Oppositely assembled tubes will

cause a sealing failure. Before assembling

the tubes, check for deterioration or cracks

and change will new ones if necessary.

4-11 Reed Valve Assembly

HBZ26 Series

● Check that there is no foreign matter inside the

valve case.

Check the gap between the valve case and

the reed valve.

Replace with new valve if the gap is larger

than 0.2 mm (0.008 in.), or the valve is

distorted.

● Screw lock agent shall be applied to the reed valve

and the stopper fixing screw.

● The reed valve case has a marking either “S” or

“F”.

“S” is for the starter side, and “F” for the fan side.

Assembling position shall not be mixed up.

CAUTION

Marks

Lead Air Intake Tube

Valve Case

Reed Valve and Mounting Screw

Valve Case

Reed Valve

Stopper

Max. 0.2 mm

(0.008 in.)

“S” Mark

Valve Case

【

【【

【Starter Side】

】】

】 【

【【

【Fan Side】

】】

】

“F” Mark

Valve Case

IMPORTANT

26

4. Service Guide

4-12 Gasket Assembly

All Models

Each gasket has its installing direction. Pay attention

to the direction when the gasket is being installed.

When the engine is overhauled, replace the

gaskets with new ones.

Model Gasket Positions Model Gasket Positions

HB23 Series

EBZ4800

EBZ51 Series

HBZ26 Series

EB6200

EB70 Series

EBZ30 Series

EBZ71 Series

EBZ80 Series

EB4300

Gasket Positions

【

【【

【Starter Side】

】】

】

【

【【

【Fan Side】

】】

】

A,

Insulator

Gasket

C, Muffler Gasket

B, Base Gasket

CAUTION

A

B

C

A

B

C

A

B

C

A

B

C

A

B

C

A

B

C

Aluminum

Gasket

A

B

C

27

4. Service Guide

4-13 Scavenging Duct Cover Assembly

EBZ30/ 71/ 80 Series

The scavenging duct covers have marking either “S”

for starter side or and “F” for fan side.

They must not be oppositely assembled.

When the engine is overhauled, be sure to

replace the gaskets with new ones.

EBZ4800, EBZ51 Series Strato Charged

engines have no scavenging duct covers.

4-14 Muffler Assembly

EB4300/ 6200, EB70 Series, EBZ4800, EBZ51/ 71/ 80 Series

Tighten the three muffler mounting bolts to the same

pressure.

・

・・

・ The bracket may be damaged if the two

muffler mounting bolts (long) on the upper

side are securely tightened before the

mounting bolt (short) on the lower side, is

tightened.

・

・・

・ After the engine is reassembled, run it at full

throttle for more than one minute, then

tighten the muffler mount bolts again.

Torque: 8～

～～

～12N・

・・

・m (80～

～～

～120kgf・

・・

・cm)

CAUTION

CAUTION

Gasket

“S” Scavenging Duct Cover

【

【【

【Starter Side】

】】

】 【

【【

【Fan Side】

】】

】

“F” Scavenging Duct Cover

Gasket

Mounting Bolts (long)

Mounting Bolts (short)

Muffler

Bracket

REFERENCE

28

4. Service Guide

4-15 Switch Cord Assembly

Switch Cord Assembly HB23 Series, HBZ26 Series

● Fit the switch cord connector firmly to the module’s

terminal.

● Secure the switch cord terminal with the module

mounting bolt.

Switch Cord Assembly EBZ30 Series

● Secure the switch cord terminal (black) with the

module mount bolt. Tilt the terminal about 45

degrees rightward.

Ensure the cord is not bent nor interfering

with the crankcase.

● Fit the switch cord connector (red) firmly to the

module’s terminal.

CAUTION

Connector

Switch Cord

【

【【

【HB23 Series】

】】

】

Module

【

【【

【HBZ26 Series】

】】

】

Connector

Switch Cord

Module

Te r m in al

Connector

Switch Cord

Module

Te r m in al

About 45 Degrees

29

4. Service Guide

Switch Cord Assembly EB4300/ 6200, EB70 Series

● Secure the switch cord terminal with the module

mounting bolt.

Ensure the cord is not bent nor interfering

with the crankcase when the module mount

bolt is tightened.

● Bends the terminal of the module, fit the switch

cord connector firmly to the module’s terminal.

Bend the module’s terminal until the cord is

clear of the crankcase.

Switch Cord Assembly EBZ4800, EBZ51/ 71/ 80 Series

● Secure the switch cord terminal with the module

mounting bolt.

Bring the terminal into contact with the

crankcase’s protrusion then tighten it.

● Fit the switch cord connector firmly to the module’s

terminal.

CAUTION

CAUTION

CAUTION

Connector

Switch Cord

Module

Te r m in al

Module’s terminal

【

【【

【EBZ5100】

】】

】

Connector

Switch Cord

Module

Te r m in al

Connector

Switch Cord

Module

Te r m in al

【

【【

【EBZ4800, EBZ5100Q, EBZ71/ 80 Series】

】】

】

Crankcase’s

protrusion

Contact

30

4. Service Guide

4-16 Cable Wiring

Switch Cord Wiring HB23 Series, HBZ26 Series

● Insert the grommet to align with the volute case

notch and clamp the cord between the protrusions

as shown in the figure at left.

Check that the cord on the module side is not

caught between volute case and crankcase.

● Pay attention that the cord is not caught against the

engine cover when it is installed.

Switch Cord Wiring EBZ30 Series

● Align the cord along the guide, and insert the

grommet to align with the volute case notch.

Check that the cord on the module side is not

caught between volute case and crankcase.

● Set the lead cords and clamp them as shown in the

figure at left.

Align the cord not to interfere with the clamp

mounting screw.

● Pay attention that the cord is not caught against the

engine cover when it is installed.

High Tension Cord Wiring EB4300/ 6200, EB70 Series, EBZ4800, EBZ51/ 71/ 80 Series

Insert the grommet to align with the crankcase's notch

and align the high tension cord and secure it with the

clamp as shown in the figure at left.

Align the high tension cord not to interfere

with the crankcase or the clamp mounting

screw.

CAUTION

CAUTION

CAUTION

CAUTION

Cords

Grommet

Cords

Grommet

Cord

Clamp

Crankcase

Clamp

Grommet

High Tension

Cord

31

4. Service Guide

4-17 Fan Assembly

All Models

● Insert the stopper (special tool) into the plug hole

(refer to “3 Special Tool”).

● Tighten the mounting nut so that the fan securely

meets the rotor without looseness.

If the fan is installed with four mounting

bolts, secure them with equal pressure in

diagonal order.

4-18 Backpack Pad Air Supply Pipe Assembly

EB4300/ 6200, EB70 Series, EBZ4800, EBZ51/ 71 Series

Firmly insert the tip of the air supply nozzle into the

frame air inlet pipe.

4-19 Upper Spring Damper Assembly

EBZ30 Series

Reassembly of the upper spring damper is the reverse

procedure of disassembly.

Refer to "4-3 Upper Spring Damper Removal".

Check that the each spring edge is firmly

mated with the volute cover and spring

holder's groove.

CAUTION

CAUTION

Fan

Mounting Nut

Torque:

9.8～14.7N・m

(100～150kgf・cm)

Mounting Bolt

Torque:

7.8～11.8N・m

(80～120kgf・cm)

Fan

【

【【

【HB23/ 26 Series】

】】

】

1

2

3

4

Frame

Nozzle

Pipe

Volute Cover Spring Holder

32

4. Service Guide

4-20 Upper Damper Assembly

EB4300/6200, EB70 Series, EBZ4800, EBZ51/ 71/ 80 Series

Assemble the damper and volute cover by mating

their protrusions.

Check that the damper is not tilted. Improper

installation will result in rapid damage.

4-21 Lower Damper Assembly

EB4300/6200, EB70 Series, EBZ4800, EBZ51/ 71/ 80 Series

Grip the damper's metal flange with the pliers in order

not to twist the rubber unit and tighten the mounting

nut with a wrench.

CAUTION

Vibration

Proof

Damper

Pliers

Mounting Nut

Wrench

Damper

Volute Cover

Volute Cover Protrusion

Damper Protrusion

33

4. Service Guide

4-22 Carburetor Assembly

EBZ71/ 80 Series

Tighten the screws of the earth cord between the

carburetor's adjuster unit and the crankcase.

This cord prevents electrostatic sparks.

Do not fail to connect it.

4-23 Engine Cover Assembly

Check of the Gasket Assembly HB23 Series

When the engine cover is installed, pay attention to

installing the muffler’s gasket to the inside the cover to

protect the fuel tank from heat.

Check of the Gasket Assembly HBZ26 Series

When the engine cover is installed, pay attention to

installing the insulator gasket to the inside of the cover

to protect the carburetor from heat.

CAUTION

Carburetor

Earth Cord

Engine Cover

Fuel Tank

Muffler Gasket

Engine Cover

Carburetor

Insulator Gasket

34

4. Service Guide

4-24 Check of the Gasket Assembly

EBZ4800, EBZ51/ 71/ 80 Series

Check that the master and insulator gaskets are set

inside the cylinder plate before the engine cover is

installed.

If the gasket is improperly set, engine cooling

performance will be reduced.

EB4300/ 6200, EB70 Series

Check that the master gasket is set outside of the

cylinder plate and the insulator gasket is set inside the

volute case before the engine cover is installed.

If the gasket is improperly set, engine cooling

performance will be reduced.

CAUTION

CAUTION

Cylinder Plate

Insulator Gasket Muffler Gasket

【

【【

【Intake Side】

】】

】 【

【【

【Exhaust Side】

】】

】

Cylinder Plate

Cylinder Plate

Insulator Gasket Muffler Gasket

Volute Case

【

【【

【Intake Side】

】】

】 【

【【

【Exhaust Side】

】】

】

35

4. Service Guide

Husqvarna Zenoah engine blowers are equipped with spark arresters to prevent spark dispersion.

・

・・

・ The Spark arrester prevents burnt carbon discharging from the muffler.

Even though the spark arrester can easily clog with carbon, never operate the blower with the

spark arrester detached.

・

・・

・ The EB4300 and EBZ4800 (Japanese specifications) are not equipped with spark arresters.

4-25 Spark Arrester Removal

HB23 Series, HBZ26 Series

1. Remove the engine cover.

(Refer to “3. Special Tools”)

2. Remove the two mounting bolts and then remove

the muffler.

Torque:

HB23 Series: 6.9～9.8N・m (70～100kgf・cm)

HBZ26 Series: 6.9～10.8N・m (70～110kgf・cm)

3. Remove the spark arrester.

EBZ30 Series

1. Remove the engine cover.

(Refer to “3. Special Tools”)

2. Remove the two mounting bolts and then remove

the muffler.

Torque: 6.9～10.8N・m (70～110kgf・cm)

3. Remove the two mounting bolts (torx) and then

attach the diffuser (diffusing cover).

Torque: 2～3N・m (20～30kgf・cm)

4. Remove the spark arrester.

EB4300/ 6200, EB70 Series

1. Remove the engine cover.

(Refer to “3. Special Tools”)

2. Remove the three mounting bolts and then remove

the muffler.

Torque: 7.8～11.8N・m (80～120kgf・cm)

3. Remove the spark arrester.

CAUTION

Spark Arrester

Mounting Bolt

×2

Muffler

Spark Arrester

Mounting Bolt

×2

Muffler Mounting Bolt

×2

Diffuser

Spark Arrester

Mounting Bolt (long)

×2

Muffler

Mounting Bolt (short)

36

4. Service Guide

EBZ51/ 71/ 80 Series

1. Remove the engine cover.

(Refer to “3. Special Tools”)

2. Remove the three mounting bolts and then remove

the muffler.

Torque: 7.8～11.8N・m (80～120kgf・cm)

3. Remove the four mounting bolts (torx) and then

attach the diffuser (diffusing cover) and the spark

arrester.

Torque: 2～3N・m (20～30kgf・cm)

4-26 Spark Arrester Cleaning

Exceptions for EB4300, EBZ4800 (Japanese specifications)

Remove any carbon slag adhering to the spark

arrester (screen) with a brush, preferably wire-type or

equivalent.

Never overheat the spark arrester with a gas

torch or other flame. The spark arrester may

deform with heat.

4-27 Muffler Cleaning

All Models

Insert a screwdriver into the vent, and wipe away any

carbon buildup. Wipe away any carbon buildup on the

muffler exhaust vent and cylinder exhaust port at the

same time.

CAUTION

Spark Arrester

Mounting Bolt (long)

×2

Muffler

Mounting Bolt

×4

Diffuser

Mounting Bolt (short)

Spark Arrester

Spark Arrester

Screwdriver

Muffler

37

4. Service Guide

4-28 Air Cleaner Inspection

This device blows fallen leaves to a collection point but at the same time small particles (dust and sand)

become airborne. If such dust invades the engine, the engine mechanism will wear quickly.

So periodically check and clean the element according to the following table.

・

・・

・ The power blower operating environment is very dusty so the air cleaner will clog more

quickly than that of other power tools. Neglecting air cleaner check and maintenance will

cause rapid engine wear and poor engine performance.

・

・・

・ The urethane element may deteriorate and crumble if the ambient temperature fluctuates

greatly. If temperature related engine trouble is observed, resolve the trouble cause then

replace the filter with a new one.

Inspection Period

Operating Hours

Inspection Item Daily 25 hours 50 hours 100 hours Remarks

Element ○△ ☆

Pre-filter ○△ ☆

If this material is damaged, deformed, or aged and

crumbling, replace it with a new one.

（Annual replacement is recommended.）

Paper Filter ○△ ○△☆

If this filter is cleaned six times or more before the

replacement interval arrives, the paper part darkens

or water or oil adheres, replace it with a new one.

(Annual replacement is recommended)

○: Inspection △: Clean ☆: Replace

4-29 Element Removal

Single layer dry urethane foam HB23 Series

Remove the cover while pressing the clip. Remove

the two elements.

Single layer dry urethane foam HBZ26 Series, EBZ30 Series

Loosen the knob then remove the element.

CAUTION

Silencer

Cover

Elements

Screen

Plate

Clip

Cover

Element

Screen

Packing

Knob

Knob

38

4. Service Guide

Single layer half-wet urethane foam EB4300/ 6200

Loosen the knob then remove the element.

Dual layer half-wet urethane foam EBZ4800

Loosen the knobs then remove the elements.

Single layer half-wet urethane foam EBZ51 Series

Loosen the knobs then remove the element.

Two stage dry element (Pre-filter + Paper filter) EB70 Series, EBZ71 Series

Loosen the knob bolts then remove the element

(pre-filter + paper filter).

Cover

Element

Screen

Screw

Knob

Knob

Cover

Elements

Yellow Black

Screen

Knobs

Knobs

Packing

Cover

Element

Screen

Knobs

Knobs

Packing

Cover

Pre-filter

Knob Bolts

Paper Filter

39

4. Service Guide

Two stage dry element (Pre-filter + Paper filter) EBZ80 Series

Loosen the knob bolts then remove the element

(pre-filter + paper filter).

4-30 Element Cleaning

Element and pre-filter rinsing All Models

● Rinse the element carefully with warm water diluted

detergent or washing oil.

Confirm that no deformity, damage or

deterioration (if touched, element will

crumble) exists.

If necessary replace it with a new one.

● After rinsing it, tighten squeeze the element to

remove moisture.

● For a HB23 series and HBZ26 series element or a

EB70 series and EBZ71/ 80 series pre-filter, dry it

after rinsing and then install it.

Caution for element installation EB4300/ 6200, EBZ4800, EBZ51 Series

The half-wet urethane element should be moistened

with 2-cycle engine oil, softly squeezed, then installed.

・

・・

・ Excessive oil adhesion will cause filter

clogging.

・

・・

・ Never moisten pre-filter (EB70 series and

EBZ71/80 series) with engine oil.

If engine oil adheres to the filter, the paper

layer will not function.

Two stage dry paper filter cleaning EB70 Series, EBZ71/ 80 Series

Blow compressed air from inside/outside of the filter

along the filter element's pleats.

Never beat or hit the filter.

CAUTION

CAUTION

CAUTION

Cover

Pre-filter

Knob Bolts

Case

Paper Filter

Warm water diluted

detergent or washing oil

2-cycle engine oil

40

5. Structure of Right Hand Throttle Lever

● The right hand throttle lever specifications (RH) employs a governor mechanism for easy blower operation

with constant wind pressure.

Throttle Lever

Throttle Lock Lever

Light Handle

<Configuration>

The throttle lock lever is fixed by plate spring

pressure.

If the plate spring pressure decreases over its

operational life, the throttle lever will lose its

locking function.

If plate spring pressure decreases, replace it

with a new one.

Throttle lever

Throttle Lock Lever

Height: 1.42 to 1.65 mm

(0.056 to 0.065 in.)

Snap Ring

Washer

Spring Washer

Washer

Shaft

<Caution in switch cord installation>

Thread the switch cord into the handle case slit and set its terminal 90 to 100 mm (3.54 to 3.94 in.) from the end of the

slit.

＊ Confirm that the switch cord remains slack when the switch is moved.

90 to 100 mm

(3.54 to 3.94 in.)

Slacken cord.

Switch Cord

<Governor Mechanism>

It is a mechanism where the throttle lever can be fixed by

a throttle lever lock at a chosen position.

The suitable engine speed can be set for operating load.

Throttle Lever Functional State

Throttle Lever Locked State

Throttle lever's

protrusion

Throttle lock lever's protrusion

Throttle lever

functional area

Throttle lever

locking area

41

6. Carburetor

6-1 Specifications

Model Carburetor (Walbro) Carburetor Specifications

Seal (L-needle)

Sales Region Blower

Model

Engine

Type

Type

Name

Part

Number Part Name Part Number

Adjustment angle

(L-needle return

angle)

Adjustment angle

(H-needle return

angle)

Main Jet

Venturi Bore

(Lead Air)

mm (in.)

Venturi Bore

(Mixture Air)

mm (in.)

Choke Bore

mm (in.)

Metering Lever

Height

mm (in.)

Valve Opening

Pressure

kg/ cm2 (kpa)

Valve Closing

Pressure

kg/ cm2 (kpa)

EU/ General HB2302 G23L WYJ-110A 5516-81000 Limiter Cap 848-F40-80D0 Adjustment FIXED # 38

―

9 (0.354) 17 (0.669) 1.5±0.16

(0.059±0.006) 1.3～2.3 0.6～1.6

EU/ General HBZ2601 GZ25N WYA-26E 848-F3C-8102 ↑ ↑ ↑ ↑ # 37.5 8 (0.315) 9 (0.354) 13.2 (0.520) ↑ ↑ ↑

USA HBZ2601 ↑

↑↑

↑ WYA-65 848-F3U-8100 ↑ ↑ ↑ 1 3/4±1/2

―

9 (0.354) 7 (0.276) 13.2 (0.520) ↑ ↑ ↑

USA/ EU/

General EBZ3000/ RH GZ30N WYA-73B 848-F6B-8101 ↑ ↑ ↑ FIXED # 34 9 (0.354) 7 (0.276) 13.2 (0.520) ↑ ↑ ↑

General EB4300 G4K WYK-67A 3407-81000 ↑ ↑ ↑ ↑ # 60

―

13.5 17 (0.669) ↑ ↑ ↑

EU/ General EBZ4800 GZ48N WYA-51B 848-L38-8100 ↑ ↑ ↑ ↑ # 45 10.5 (0.413) 10.5 (0.413) 14.5 (0.571) ↑ ↑ ↑

GZ51N3.5 WYA-74A 848-HE0-8100

USA EBZ5100/ RH GZ51N6 WYA-79 848-HE2-8100

↑ ↑ ↑ ↑ # 44 10.5 (0.413) 10.5 (0.413) 14.5 (0.571) ↑ ↑ ↑

USA EBZ5100Q GZ51N7 WYA-83 848-HE6-8100 ↑ ↑ ↑ ↑ # 41.5 10.5 (0.413) 10.5 (0.413) 14.5 (0.571) ↑ ↑ ↑

General EB6200 G62L WYK-73A 2750-81000 ↑ ↑ ↑ ↑ # 59

―

15 (0.591) 17 (0.669) ↑ ↑ ↑

EU/ General EB7000 ↑

↑↑

↑ WYK-123A T4012-81000 ↑ ↑ ↑ ↑ # 53

―

15 (0.591) 17 (0.669) ↑ ↑ ↑

USA EBZ7100/ RH GZ65N WYA-81 848-H18-8100 ↑ ↑ ↑ ↑ # 57 13.5 (0.532) 12.2 (0.480) 14.5 (0.571) ↑ ↑ ↑

USA/ EU/

General EBZ8001/ RH GZ72N WYA-44B 848-H00-8100 ↑ ↑ ↑ ↑ # 59 13. 5 (0.532) 12.2 (0.480) 14.5 (0.571) ↑ ↑ ↑

Model Adjustment Angle for Engine Start

(Loosen then tighten) Engine Speed (rpm) Standard Engine Speed (rpm)

Sales Region Blower

Model

Engine

Type

Throttle

Valve Adjust

Screw

L-needle

Adjustment

Angle

H-needle

Adjustment

Angle

ID Peak

Engine

Speed

ID Rich

Down

Set ID

Engine

Speed

H Rich

Down

Set H

Engine

Speed

Idling Full Throttle

(Standard Pipe)

Remarks Recommended Tools

EU/ General HB2302 G23L 9 13 FIXED 3400±10 1000～1200 2300±100 FIX JET FIX JET 2300±200 7300～7600

EU/ General HBZ2601 GZ25N 8 1/2 12 1/2 ↑ 3700±10 800～1000 2800±100 ↑ ↑ 2800±200 7700～7990

USA HBZ2601 ↑

↑↑

↑ 8 1/2 13 1/2 1 7/8 3900±10 1000～1200 2800±100 50～100 7300 2800±200 7300～7800

USA/ EU/

General EBZ3000/ RH GZ30N 8 1/2 12 FIXED 3500±10 400～100 3000±100 FIX JET FIX JET 3000±200 6300～6800

General EB4300 G4K 4 1/2 10 1/2 ↑ 2700±10 600～800 2000±100 ↑ ↑ 2000±200 6150～6550

EU/ General EBZ4800 GZ48N 11 1/2 9 ↑ 3400±10 1000～1200 ↑ ↑ ↑ ↑ ↑

GZ51N3.5 9 11 1/2 3000±10 700～900

USA EBZ5100/ RH

GZ51N6 6 10

↑

2900±10 600～800

2200±100 ↑ ↑ 2200±200 5820～6100

Digital magneto controlled misfire

for excessive speed

Maximum speed: 8500 rpm

USA EBZ5100Q GZ51N7 3 1/2 10 ↑ 2900±10 600～800 2200±100 ↑ ↑ 2200±200 5520～5800

General EB6200 G62L 4 10 1/2 ↑ 2500±10 400～600 2000±100 ↑ ↑ 2000±200 7500～7800

EU/ General EB7000 ↑

↑↑

↑ 7 10 1/2 ↑ 2700±10 600～800 ↑ ↑ ↑ ↑ 7100～7500

USA EBZ7100/ RH GZ65N 7 12 ↑ 2700±10 600～800 2000±100 ↑ ↑ 2000±200 6850～7150

Digital magneto controlled misfire

for excessive speed

Maximum speed: 8500 rpm

USA/ EU/

General EBZ8001/ RH GZ72N 6 1/2 12 ↑ 2700±10 600～800 2000±100 ↑ ↑ 2000±200 6500～6800

Digital magneto controlled misfire

for excessive speed

Maximum speed: 8500 rpm

① 3699-90345

Carburetor Conditioner

④ 848-8W9-0080

Limiter Cap Tool

② 3699-90211

Leak Tester

③ 3699-90537

Tachometer PET-1000

42

6. Carburetor

6-2 Carburetor Configuration

Inspection and adjustment items

Execute the following check and adjustment if the carburetor does not function normally.

(Refer to "6-5 Idling Speed Adjustment " and "6-6 Carburetor Inspection".)

● Fuel adjustment when idling

● Check of the body assembly

● Check of the main check valve

● Check of throttle valve

Readjust the engine rotational speed referring to "6-7 Carburetor Adjustment"

if the engine speed is not steady after the above-mentioned adjustment and the checks are executed.

L-needle

Construction

【

【【

【Type: WYJ】

】】

】 【

【【

【Type: WYA】

】】

】

Main Jet

Main Check Valve

Body Assembly

Inlet Valve

Main Diaphragm

Metering Lever

Screen

L- needle

Main Jet

Main Check Valve

Body Assembly

Inlet Valve

Main Diaphragm

Metering Lever

Screen

H-needle

【

【【

【USA/ HBZ2601 only】

】】

】

Throttle Valve Assembly Throttle Valve Assembly

43

6. Carburetor

6-3 Carburetor Conforms to Exhaust Emissions Regulations

The carburetor flow rates of all Hasqvarna Zenoah engine blowers are individually pre-adjusted to pass

exhaust emissions regulations.

A limiter cap is installed in the idling limiter to prevent an operator carelessly changing the idle setting resulting

in non-conformance with exhaust emission regulations.

Execute a correct adjustment according to "6-7 Carburetor Adjustment".

A limiter cap closes the L-needle adjustment hole of

the throttle valve.

Carburetor adjustments with caps removed must be conducted by Emission Certified

Servicing Dealers ONLY.

The dealer must supply the unit to the customer in original configuration, using the

manufacturer’s carburetor adjustment procedure, which includes having the limiter caps in

place before the unit is put into service.

Knowingly removing or rendering inoperative any device, element, or design installed on or in

a non-road engine which is in compliance with E. P. A. or C. A. R. B. (USA), STAGEⅢ

ⅢⅢ

Ⅲ(EU)

regulations is classified as TAMPERING.

TAMPERING is a violation of FEDERAL LOW, resulting in significant civil penalties (fines) of up

to $25,000 for each violation.

ATTENTION!!! IMPORTANT!!!

L-needle

Limiter Cap

Throttle Valve

44

6. Carburetor

6-4 Limiter Cap Removal/ Installation

Tool

The limiter cap tool (carburetor maintenance tool:

848-8W9-0080) is used for limiter cap

installation/removal.

Removal

Insert the limiter cap tool extraction tool's threading

(M2 counterclockwise threading) into the idling

limiter's hole and screw it counterclockwise while

giving pressure.

When it is firmly threaded, pull the limiter cap.

If it is difficult to screw in the limiter cap tool,

firmly press the tool while screwing. When

threads are completely meshed, pull it out in

one stroke. If cap is damaged and stays in

the hole, use a pick type tool to remove it.

Installation

Insert a new limiter cap in the low speed mixture

needle hole. Press the cap deeply into low speed

mixture needle hole to prevent tampering.

Be sure to install only a new limiter cap.

The limiter cap is a very small part. Pay

attention not to lose it.

6-5 Idling Speed Adjustment

Slow and Middle Speeds All Models

Adjust the fuel supply under idling conditions by turning the idling limiter.

1. Remove the limiter cap.

(Refer to "6-4 Limiter Cap Removal/ Installation".)

After completion of the adjustment, be sure

to install the limiter cap.

2. Turn the screw with a commercially available screw

driver (tip width: 2.5mm).

Clockwise (CW):

Fuel mixture becomes lean. (Speed increases.)

Counterclockwise (CCW):

Fuel mixture becomes rich. (Speed decreases.)

CAUTION

CAUTION

Limiter cap insertion side

Limiter cap

(new part)

CAUTION

Screw Driver Increases Decreases

Limiter cap insertion side

Limiter cap tool extraction side

Screw unit

(M2 counterclockwise threading)

Limiter Cap Tool

Limiter Cap

Limiter cap tool extraction side

Press it while turning it

counterclockwise. Pull it out.

Limiter cap is

removed.

45

6. Carburetor

High Speed Adjustment 【

【【

【USA/ HBZ2601 only】

】】

】

High speed revolutions are adjusted by a H-needle.

Clockwise (CW):

Fuel mixture becomes lean. (Speed increases.)

Counterclockwise (CCW):

Fuel mixture becomes rich. (Speed decreases.)

6-6 Carburetor Inspection

Inlet Valve Leaking Test

Connect a leak tester to the fuel inlet port of the carburetor.

After filling the metering chamber with fuel, apply pressure to the inlet valve and read the opening pressure

and the reseating pressure.

a. Body assembly normality check

● Measure the metering lever height using a depth

gauge or scale.

The appropriate value is 1.5±0.16 mm (0.059±

0.006 in.)

● Check that no wear exists on the metering lever or

diaphragm contacting areas.

If wear exists, replace it with a new one.

● Remove the inlet valve and check for dirt, sludge,

rusting and/or step-wear.

Replace the inlet valve if a step is found on the

rubber tip.

● Check that no alien matter adheres to the valve

sheet part. If any alien matter exists, dip the valve

sheet in gasoline for about 10 minutes and remove

it, or use the carburetor conditioner (Carburetor

Conditioner: 699-90345) to clean it.

● Check that no alien matter has accumulated on the

screen.

If screen is clogged with alien matter, remove the

screen and clean it.

H-needle

Increases

Decreases

Metering Lever

Inlet Valve

Rubber Tip

1.5±0.16 mm

(0.059±0.006 in.)

Body

Assembly

Metering Lever

Main Diaphragm

Valve Sheet

Screen

Body Assembly

46

6. Carburetor

b. Judgments of the main check valve

● As illustrated, hold a plastic pipe on the check

valve and blow and suck air by your mouth. If the

air is stopped by blowing, and open by sucking, the

valve has no failure.

● In case of failure, soak the valve into gasoline for

about 10 minutes and repeat blowing and sucking

several times.

If this is not successful, replace the body assembly.

● Make sure to check the valve in case fuel is not

supplied though the priming pump is operated.

c. Throttle valve normality check

● Check that no wear exists in the throttle valve slide.

Carefully slide a screw driver tip along the plunger's

contact surface.

If the screw driver tip catches in a groove, replace

the carburetor assembly with a new one.

● Check that no wear exists on the jet needle.

If there are signs of vertical linear flaws or wear,

replace the carburetor assembly with a new one.

Even small damage will increase fuel

consumption.

Plunger

Throttle Valve Assembly

Contact Surface

CAUTION

Jet Needle Portion

Damage Wear

Plastic Pipe

Main Check Valve

Body Assembly

47

6. Carburetor

6-7 Carburetor Adjustment

Before performing carburetor adjustment, the following areas must be inspected for good

working order.

● Correct spark plug set to specified gap must be installed.

● The air filter and paper filter must be clean and properly installed.

● The muffler spark arrestor screen and exhaust port must be clear of carbon.

● The fuel filter must be clean and properly installed.

● The carburetor and carburetor insulator block screw must be tight.

● The fuel must be fresh (properly mixed at 40:1 ratio with Zenoah or 50:1 ratio with RedMax)

● All standard air tubes (Air Pipes) must be installed.

● No fallen leaf or other matter must be adhered to the air intake.

Required Tools and Parts

● Carburetor adjustment screw driver 2.5mm flat tip

● Electronic digital tachometer

● Limiter cap removal tool

● New Limiter cap

Adjustment when engine activated

1. Start the engine and alternate three times between

the idling state (10 seconds) and full throttle state

(60 seconds). Then check the engine's condition.

2. If idling is not stable, remove the limiter cap (refer

to "6-4 Limiter Cap Removal/ Installation") and

adjust the engine according to the following

procedure.

● Throttle valve adjust screw

Clockwise (CW) 1&1/2 turn:

Increases engine speed.

● L-needle

Counterclockwise (CCW) 1/8 turn:

Enriches the fuel mixture.

(Reduces engine speed.)

● H-needle 【

【【

【USA/ HBZ2601 only】

】】

】

Counterclockwise (CCW) 1/8 turn:

Reduces engine speed.

3. Run the warm-up operation (see the above table)

and execute the rich down adjustment.

(Refer to "Rich Down Adjustment".)

Throttle Valve

Adjust Screw

1&1/2 turn

L-needle 1/8 turn

H-needle

【

【【

【USA/ HBZ2601 only】

】】

】

1/8 turn

Idling

Full

Throttle

1st Time 2nd Time 3rd Time

48

6. Carburetor

Adjustment if engine does not activate

Set the adjustable parts as specified according to the

following procedure.

1. Loosen the throttle valve adjust screw until the

throttle valve becomes completely free, then turn

the screw clockwise until the regulated angle is

attained.

(Refer to "6-1 Specifications- Adjustment Angle for

Engine Start".)

2. Turn the idling limiter (L-needle) counterclockwise

until it becomes free. (When the needle screw

completely loosens, a click tone can be heard.)

Turn the idling limiter clockwise from this position

until the regulated angle is attained.

(Refer to "6-1 Specifications- Adjustment Angle for

Engine Start- L-needle Adjustment Angle".)

When tightening the L-needle clockwise,

never excessively tighten it.

Doing so may cause damage to the needle

surface resulting in excessive or inconsistent

fuel supply.

3. H-needle 【

【【

【USA/ HBZ2601 only】

】】

】

Clockwise (CW) completely, then back it off 1&7/8

turns counterclockwise (CCW).

4. Start the engine and execute the rich down

adjustment. (Refer to "Rich Down Adjustment".)

If the engine still does not start, problems

may exist elsewhere than the carburetor.

Check those other causes.

CAUTION

CAUTION

Throttle Valve

Adjust Screw

L-needle

H-needle

【

【【

【USA/ HBZ2601 only】

】】

】

49

6. Carburetor

Rich Down Adjustment

1. Turn the idling limiter (L-needle) clockwise to the

position of maximum engine speed.

2. Turn the throttle valve adjust screw in either

direction to match to the regulated ID peak speed.

(Refer to "6-1 Specifications- ID Peak Engine

Speed".)

3. Turn the L-needle counterclockwise and execute

the rich down adjustment.

(Refer to "6-1 Specifications- ID Rich Down".)

4. Turn the throttle valve adjust screw in either

direction and set the ID speed.

(Refer to "6-1 Specifications- Set ID Engine

Speed".)

5. Check that rotational speed accelerates normally

between idling state and full throttle within the

regulated number of revolutions.

(Refer to "6-1 Specifications- Standard Engine

Speed".)

【

【【

【USA/ HBZ2601 only】

】】

】

After the above adjustment is completed, adjust the

H-needle.

1. Turn the H-needle clockwise so that the speed

reaches its peak (7300 to 7800 rpm).

2. When the speed reaches its peak, turn the

H-needle counterclockwise until the speed falls 50

to 100 rpm. (Set H Engine Speed: 7300 rpm)

The HBZ2601 rich down procedure might not

optimize the L-needle and H-needle

relationship at first try.

If so repeat this procedure twice.

Throttle Valve

Adjust Screw

L-needle

H-needle

Rich Down:

Adjust the idle needle to a slightly richer mixture in order

to maintain a stable idling speed and get a good

acceleration.

Peak engine speed

Set engine speed

Peak

Rich Down

Best

Consumption (ℓ/h)

(rpm)

REFERENCE

50

6. Carburetor

Confirmation after adjustment

● After adjustment is completed, be sure to install the

new limiter cap.

(Refer to "6-4 Limiter Cap Removal/ Installation".)

● Be sure to reattach the dust cover.

If the engine is run while the throttle valve's

dust cover is removed, dust or alien matter

may adhere to the throttle valve's rear

contoured or the plunger contacting

surfaces.

If they become worn, the L-needle will fall

causing engine start failure.

CAUTION

Dust Cover

Limiter Cap

51

7. Maintenance Standards

7-1 Engine

Maintenance Item Unit Specifications

Category －

－－

－ Handheld Blower Backpack Blower

Engine Type －

－－

－ G23L GZ25N GZ30N G4K GZ48N GZ51N G62L GZ65N GZ72N

HB2302

HB2311EZ HBZ2601 EBZ3000/ 3000RH

EBZ3050RH EB4300 EBZ4800

EBZ5100/ 5100RH/

5100Q

EBZ5150/ 5150RH/

5150Q

EB6200

EB7000

EB7001

EBZ7100/ 7100RH

EBZ7150/ 7150RH

EBZ8001/ 8001RH

EBZ8050/ 8050RH

Model Blower Model －

－－

－

Standard Limit Standard Limit Standard Limit Standard Limit Standard Limit Standard Limit Standard Limit Standard Limit Standard Limit

Measuring

Instrument

Service

Procedure

Cylinder Bore mm (in.) φ32.00

(1.2598)

φ32.06

(1.2622)

φ34.00

(1.3386)

φ34.06

(1.3409)

φ38.00

(1.4961)

φ38.06

(1.4984)

φ40.00

(1.5748)

φ40.06

(1.5772)

φ43.00

(1.6929)

φ43.06

(1.6953)

φ44.00

(1.7323)

φ44.06

(1.7346)

φ47.50

(1.8701)

φ47.56

(1.8724)

φ47.53

(1.8713)

φ47.59

(1.8736)

φ50.03

(1.9697)

φ50.09

(1.9720) Cylinder Gauge

Replacement

(Plating Damaged

Replacement)

Piston Diameter

(Skirt) mm (in.)

φ31.945

(1.2577)

～φ31.960

(1.2583)

φ31.86

(1.2543)

φ33.960

(1.3370)

～φ33.975

(1.3376)

φ33.86

(1.3331)

φ37.950

(1.4941)

～φ37.970

(1.4949)

φ37.86

(1.4906)

φ39.960

(1.5732)

～φ39.975

(1.5738)

φ39.87

(1.5697)

φ42.955

(1.6911)

～φ42.970

(1.6917)

φ42.87

(1.6878)

φ43.965

(1.7309)

～φ43.985

(1.7317)

φ43.88

(1.7276)

φ47.455

(1.8683)

～φ47.470

(1.8689)

φ47.37

(1.8650)

φ47.458

(1.8684)

～φ47.478

(1.8692)

φ47.37

(1.8650)

φ49.958

(1.9669)

～φ49.978

(1.9676)

φ49.87

(1.9634) Micrometer Replacement

Top mm (in.) 1.51

(0.0594)

1.60

(0.0630)

1.03

(0.0406)

1.30

(0.0512)

1.23

(0.0484)

1.30

(0.0512)

1.57

(0.0618)

1.60

(0.0630)

1.25

(0.0492)

1.30

(0.0512)

1.25

(0.0492)

1.30

(0.0512)

1.55

(0.0610)

1.60

(0.0630)

1.25

(0.0492)

1.30

(0.0512)

1.25

(0.0492)

1.30

(0.0512)

Piston Ring

Groove Width 2nd mm (in.) 1.51

(0.0594)

1.60

(0.0630)

1.01

(0.0398)

1.30

(0.0512)

1.21

(0.0476)

1.30

(0.0512)

1.57

(0.0618)

1.60

(0.0630)

1.22

(0.0480)

1.30

(0.0512)

1.22

(0.0480)

1.30

(0.0512)

1.53

(0.0602)

1.60

(0.0630)

1.23

(0.0484)

1.30

(0.0512)

1.23

(0.0484)

1.30

(0.0512)

Thickness Gauge Replacement

Piston Pin Hole mm (in.) φ7.990

(0.3146)

φ8.04

(0.3165)

φ7.995

(0.3148)

φ8.04

(0.3165)

φ8.995

(0.3541)

φ9.04

(0.3559)

φ10.995

(0.4329)

φ11.04

(0.4346)

φ10.995

(0.4329)

φ11.04

(0.4346)

φ10.995

(0.4329)

φ11.04

(0.4346)

φ10.995

(0.4329)

φ11.04

(0.4346)

φ11.995

(0.4722)

φ12.05

(0.4744)

φ11.995

(0.4722)

φ12.05

(0.4744) Cylinder Gauge Replacement

Clearance Between

Piston and Cylinder mm (in.)

0.040

(0.0016)

～0.080

(0.0031)

0.20

(0.0079)

0.025

(0.0010)

～0.065

(0.0026)

0.20

(0.0079)

0.030

(0.0012)

～0.075

(0.0030)

0.20

(0.0079)

0.025

(0.0010)

～0.065

(0.0026)

0.19

(0.0074)

0.030

(0.0012)

～0.070

(0.0028)

0.19

(0.0075)

0.015

(0.0006)

～0.060

(0.0024)

0.18

(0.0071)

0.030

(0.0012)

～0.065

(0.0026)

0.19

(0.0075)

0.052

(0.0020)

～0.092

(0.0036)

0.22

(0.0087)

0.052

(0.0020)

～0.092

(0.0036)

0.22

(0.0087)

Micrometer,

Cylinder Gauge

Piston

Replacement

Top mm (in.)

0.02

(0.0008)

～0.06

(0.0024)

0.10

(0.0039)

0.04

(0.0016)

～0.08

(0.0031)

0.10

(0.0039)

0.04

(0.0016)

～0.08

(0.0031)

0.10

(0.0039)

0.08

(0.0031)

～0.12

(0.0047)

0.15

(0.0059)

0.06

(0.0024)

～0.10

(0.0039)

0.15

(0.0059)

0.06

(0.0024)

～0.10

(0.0039)

0.15

(0.0059)

0.06

(0.0024)

～0.10

(0.0039)

0.15

(0.0059)

0.06

(0.0024)

～0.10

(0.0039)

0.15

(0.0059)

0.06

(0.0024)

～0.10

(0.0039)

0.15

(0.0059)

Clearance

Between

Piston

Groove and

Piston Ring 2nd mm (in.)

0.02

(0.0008)

～0.06

(0.0024)

0.10

(0.0039)

0.02

(0.0008)

～0.06

(0.0024)

0.10

(0.0039)

0.02

(0.0008)

～0.06

(0.0024)

0.10

(0.0039)

0.08

(0.0031)

～0.12

(0.0047)

0.15

(0.0059)

0.03

(0.0012)

～0.07

(0.0028)

0.15

(0.0059)

0.03

(0.0012)

～0.07

(0.0028)

0.15

(0.0059)

0.04

(0.0016)

～0.08

(0.0031)

0.15

(0.0059)

0.04

(0.0016)

～0.08

(0.0031)

0.15

(0.0059)

0.04

(0.0016)

～0.08

(0.0031)

0.15

(0.0059)

Thickness Gauge Replacement

Piston

Fitting Between

Piston Pin and

Piston Pin Hole

mm (in.)

0.010T

(0.00039T)

～0.006L

(0.00024L)

0.06L

(0.00024L)

0.005T

(0.00020T)

～0.011L

(0.00043L)

0.06L

(0.00024L)

0.005T

(0.00020T)

～0.011L

(0.00043L)

0.06L

(0.00024L)

0.005T

(0.00020T)

～0.011L

(0.00043L)

0.06L

(0.00024L)

0.005L

(0.00020T)

～0.021L

(0.00083L)

0.06L

(0.00024L)

0.005L

(0.00020T)

～0.021L

(0.00083L)

0.06L

(0.00024L)

0.005L

(0.00020T)

～0.021L

(0.00083L)

0.06L

(0.00024L)

0.005L

(0.00020T)

～0.021L

(0.00083L)

0.07L

(0.0028L)

0.005L

(0.00020T)

～0.021L

(0.00083L)

0.07L

(0.0028L)

Micrometer,

Cylinder Gauge Replacement

End Gap at Cylinder

Skirt mm (in.)

0.10

(0.0039)

～0.30

(0.0118)

0.50

(0.0197)

0.10

(0.0039)

～0.30

(0.0118)

0.50

(0.0197)

0.10

(0.0039)

～0.30

(0.0118)

0.50

(0.0197)

0.10

(0.0039)

～0.30

(0.0118)

0.50

(0.0197)

0.10

(0.0039)

～0.30

(0.0118)

0.50

(0.0197)

0.10

(0.0039)

～0.30

(0.0118)

0.50

(0.0197)

0.15

(0.0059)

～0.35

(0.0138)

0.6

(0.0236)

0.15

(0.0059)

～0.35

(0.0138)

0.6

(0.0236)

0.15

(0.0059)

～0.35

(0.0138)

0.6

(0.0236) Thickness Gauge Replacement

Piston Ring

Width mm (in.) 1.5

(0.0591)

1.4

(0.0551)

1.0

(0.0394)

0.9

(0.0354)

1.2

(0.0472)

1.1

(0.0433)

1.5

(0.0591)

1.4

(0.0551)

1.2

(0.0472)

1.1

(0.0433)

1.2

(0.0472)

1.1

(0.0433)

1.5

(0.0591)

1.4

(0.0551)

1.2

(0.0472)

1.1

(0.0433)

1.2

(0.0472)

1.1

(0.0433) Micrometer Replacement

Piston Pin Diameter mm (in.) φ8.00

(0.3150)

φ7.98

(0.3142)

φ8.00

(0.3150)

φ7.98

(0.3142)

φ9.00

(0.3543)

φ8.98

(0.3535)

φ11.00

(0.4331)

φ10.98

(0.4323)

φ11.00

(0.4331)

φ10.98

(0.4323)

φ11.00

(0.4331)

φ10.98

(0.4323)

φ11.00

(0.4331)

φ10.98

(0.4323)

φ12.00

(0.4724)

φ11.98

(0.4717)

φ12.00

(0.4724)

φ11.98

(0.4717) Micrometer Replacement

Small End Bore mm (in.) φ11.00

(0.4331)

φ11.03

(0.4343)

φ11.00

(0.4331)

φ11.03

(0.4343)

φ12.00

(0.4724)

φ12.03

(0.4736)

φ15.00

(0.5906)

φ15.03

(0.5917)

φ15.00

(0.5906)

φ15.03

(0.5917)

φ15.00

(0.5906)

φ15.03

(0.5917)

φ15.00

(0.5906)

φ15.03

(0.5917)

φ16.00

(0.6299)

φ16.03

(0.6311)

φ16.00

(0.6299)

φ16.03

(0.6311) Cylinder Gauge Replacement

Connecting

Rod Parallelism of

Large/ Small End

Bores

-

0.15/ 100

-

0.15/ 100

-

0.15/ 100

-

0.15/ 100

-

0.15/ 100

-

0.15/ 100

-

0.15/ 100

-

0.15/ 100

-

0.15/ 100 Mandrel Dial

Gauge Replacement

Diameter at Main

Bearing mm (in.) φ12.00

(0.4724)

φ11.97

(0.4713)

φ12.00

(0.4724)

φ11.97

(0.4713)

φ12.00

(0.4724)

φ11.97

(0.4713)

φ15.00

(0.5906)

φ14.95

(0.5886)

φ15.00

(0.5906)

φ14.95

(0.5886)

φ15.00

(0.5906)

φ14.95

(0.5886)

φ15.00

(0.5906)

φ14.95

(0.5886)

φ16.00

(0.6299)

φ15.95

(0.6280)

φ16.00

(0.6299)

φ15.95

(0.6280) Micrometer Replacement

Crankshaft

(Starter

Side) Diameter at Oil Seal mm (in.) φ12.00

(0.4724)

φ11.90

(0.4685)

φ12.00

(0.4724)

φ11.90

(0.4685)

φ12.00

(0.4724)

φ11.90

(0.4685)

φ15.00

(0.5906)

φ14.90

(0.5866)

φ15.00

(0.5906)

φ14.90

(0.5866)

φ15.00

(0.5906)

φ14.90

(0.5866)

φ15.00

(0.5906)

φ14.90

(0.5866)

φ16.00

(0.6299)

φ15.90

(0.6260)

φ16.00

(0.6299)

φ15.90

(0.6260) Micrometer Replacement

Diameter at Main

Bearing mm (in.) φ12.00

(0.4724)

φ11.97

(0.4713)

φ12.00

(0.4724)

φ11.97

(0.4713)

φ12.00

(0.4724)

φ11.97

(0.4713)

φ15.00

(0.5906)

φ14.95

(0.5886)

φ15.00

(0.5906)

φ14.95

(0.5886)

φ15.00

(0.5906)

φ14.95

(0.5886)

φ15.00

(0.5906)

φ14.95

(0.5886)

φ16.00

(0.6299)

φ15.95

(0.6280)

φ16.00

(0.6299)

φ15.95

(0.6280) Micrometer Replacement

Crankshaft

(Fan Side) Diameter at Oil Seal mm (in.) φ12.00

(0.4724)

φ11.90

(0.4685)

φ12.00

(0.4724)

φ11.90

(0.4685)

φ12.00

(0.4724)

φ11.90

(0.4685)

φ15.00

(0.5906)

φ14.90

(0.5866)

φ15.00

(0.5906)

φ14.90

(0.5866)

φ15.00

(0.5906)

φ14.90

(0.5866)

φ15.00

(0.5906)

φ14.90

(0.5866)

φ16.00

(0.6299)

φ15.90

(0.6260)

φ16.00

(0.6299)

φ15.90

(0.6260) Micrometer Replacement

Eccentricity mm (in.)

-

0.07

(0.0028)

-

0.07

(0.0028)

-

0.07

(0.0028)

-

0.07

(0.0028)

-

0.07

(0.0028)

-

0.07

(0.0028)

-

0.07

(0.0028)

-

0.07

(0.0028)

-

0.07

(0.0028)

Dial Gauge,

Center Support

Repair or

Replacement

Width Between

Crank Webs mm (in.) 22.0

(0.8661)

21.9

(0.8622)

～22.1

(0.8701)

22.0

(0.8661)

21.9

(0.8622)

～22.1

(0.8701)

24.0

(0.9449)

23.9

(0.9409)

～24.1

(0.9488)

29.0

(1.1417)

28.9

(1.1378)

～29.1

(1.1457)

29.0

(1.1417)

28.9

(1.1378)

～29.1

(1.1457)

29.0

(1.1417)

28.9

(1.1378)

～29.1

(1.1457)

29.0

(1.1417)

28.9

(1.1378)

～29.1

(1.1457)

29.0

(1.1417)

28.9

(1.1378)

～29.1

(1.1457)

29.0

(1.1417)

28.9

(1.1378)

～29.1

(1.1457)

Micrometer Repair or

Replacement

Crankshaft

Complete

Axial Play mm (in.)

-

0.5

(0.0197)

-

0.5

(0.0197)

-

0.5

(0.0197)

-

0.5

(0.0197)

-

0.5

(0.0197)

-

0.5

(0.0197)

-

0.5

(0.0197)

-

0.5

(0.0197)

-

0.5

(0.0197) Thickness Gauge Repair (Shim)

Main Bearing (Ball Bearing) －

-

Flutter,

irregular

noise

generated

-

Flutter,

irregular

noise

generated

-

Flutter,

irregular

noise

generated

-

Flutter,

irregular

noise

generated

-

Flutter,

irregular

noise

generated

-

Flutter,

irregular

noise

generated

-

Flutter,

irregular

noise

generated

-

Flutter,

irregular

noise

generated

-

Flutter,

irregular

noise

generated

-

Replacement

52

7. Maintenance Standards

7-2 Tightening Torques

Tightening Item Unit Specifications

Category －

－－

－ Handheld Blower Backpack Blower

Engine Type －

－－

－ G23L GZ25N GZ30N G4K GZ48N GZ51N G62L GZ65N GZ72N

Model Blower Model －

－－

－

HB2302

HB2311EZ HBZ2601 EBZ3000/ 3000RH

EBZ3050RH EB4300 EBZ4800

EBZ5100/ 5100RH/

5100Q

EBZ5150/ 5150RH/

5150Q

EB6200

EB7000

EB7001

EBZ7100/ 7100RH

EBZ7150/ 7150RH

EBZ8001/ 8001RH

EBZ8050/ 8050RH

Thread size mm M14x1.25 M10x1.0 ← M14x1.25 M10x1.0 ← M14x1.25 M10x1.0 ←

Spark Plug Torque kgf・cm

(N・m)

150～220

(14.7～21.6)

100～140

(9.8～13.7) ← 150～220

(14.7～21.6)

90～130

(8.8～12.7) ← 150～220

(14.7～21.6)

90～130

(8.8～12.7) ←

Thread size mm M5x0.8 ← ← M6x1.0 ← ← ← ← ←

Muffler Torque kgf・cm

(N・m)

70～100

(6.9～9.8)

70～110

(6.9～10.8) ← 80～120

(7.8～11.8） ← ← ← ← ←

Thread size mm M5x0.8 ← ← ← ← ← ← ← ←

Cylinder Torque kgf・cm

(N・m)

60～80

(5.9～7.8)

60～90

(5.9～8.8)

60～80

(5.9～7.8)

50～80

(4.9～7.8)

60～90

(5.9～8.8) ← 50～80

(4.9～7.8)

60～90

(5.9～8.8) ←

Thread size mm M5x0.8 ← ← ← ← ← ← ← ←

Crank Case Torque kgf・cm

(N・m)

35～45

(3.4～4.4)

50～80

(4.9～7.8) ← ← ← ← ← ← ←

Thread size mm M5x0.8 ← ← ← ← ← ← ← ←

Insulator Torque kgf・cm

(N・m)

30～40

(2.9～3.9)

30～50

(2.9～4.9)

50～70

(4.9～6.9)

50～80

(4.9～7.8)

30～50

(2.9～4.9)

40～60

(3.9～5.9)

50～80

(4.9～7.8)

40～60

(3.9～5.9) ←

Thread size mm M5x0.8 ← ← ← ← ← ←

Air Cleaner and Carburetor Torque kgf・cm

(N・m)

30～40

(2.9～3.9)

30～60

(2.9～5.9) ← 30～45

(2.9～4.4) ← ← 30～45

(2.9～4.4)

Thread size mm M5xL50 M5xL60 ←

Chalk Cup and Carburetor

（

（（

（Large Air Cleaner）

））

） Torque kgf・cm

(N・m) 30～45

(2.9～4.4) ← ←

Thread size mm M4x0.7 M5x0.8 ← ← ← ← ← ← ←

Recoil Starter Torque kgf・cm

(N・m)

15～20

(1.5～2.0)

30～60

(2.9～5.9) ← 30～45

(2.9～4.4) ← ← 30～45

(2.9～4.4) ← ←

Thread size mm M8x1.0 M8x1.25 ← M10x1.0 ← ← ← M10x1.25 ←

Starter Pulley Torque kgf・cm

(N・m)

120～180

(11.8～17.6)

70～110

(6.9～10.8) ← 180～230

(17.6～22.5) ← ← ← ← ←

Thread size mm M8x1.0 ← ← M10x1.0 ← ← ← ← ←

Rotor Torque kgf・cm

(N・m)

100～150

(9.8～14.7) ← ← 200～300

(19.6～29.4) ← ← ← 250～350

(24.5～34.3) ←

Thread size mm M4x0.7 ← ← ← ← ← ← ← ←

Engine

Coil Torque kgf・cm

(N・m)

25～40

(2.5～3.9)

25～50

(2.5～4.9)

25～40

(2.5～3.9) ← ← ← ← ← ←

Thread size mm M5x0.8 ← ← M6x1.0 ← ← ← ← ←

Engine Mount Torque kgf・cm

(N・m)

30～40

(2.9～3.9) ← 40～60

(3.9～5.9)

60～80

(5.9～7.8) ← ← ← ← ←

Thread size mm P5 ← ← ← ← ← ← ← ←

Volute Case,

Volute Cover,

Engine Cover Torque kgf・cm

(N・m)

20～25

(2.0～2.5) ← 30～40

(2.9～3.9)

20～30

(2.0～2.9)

25～30

(2.5～2.9)

45～55

(4.4～5.4)

25～35

(2.5～3.4)

30～40

(2.9～3.9) ←

Thread size mm M8x1.0 ← M6x1.0 ← ← ← ← ← ←

Fan Torque kgf・cm

(N・m)

100～150

(9.8～14.7) ← 80～120

(7.8～11.8) ← ← ← ← ← ←

Thread size mm M5x0.8 ← ←

Large Air Cleaner Torque kgf・cm

(N・m) 25～35

(2.5～3.4) ← ←

Thread size mm M4x0.7 ← ← ← ← ← ← ← ←

Torque kgf・cm

(N・m)

10～15

(1.0～1.5) ← ← ← ← ← ← ← ←

Thread size mm M5x0.8 ← ← ← ← ← ← ← ←

Torque kgf・cm

(N・m)

20～35

(2.0～3.4) ← ← ← ← ← ← ← ←

Thread size mm M6x1.0 ← ← ← ← ← ← ← ←

Common Tightening Torque

Torque kgf・cm

(N・m)

40～60

(3.9～5.9) ← ← ← ← ← ← ← ←

53

8. Troubleshooting

8-1 Engine does not start

Remove the spark plug from the cylinder. Put the spark plug on the outside of the cylinder.

Pull the recoil starter knob, and check whether sparks arise in the spark gap or not.

Trouble Probable Cause Countermeasure

No spark in the spark plug.

1. Wet spark plug electrodes Make them dry.

2. Carbon deposited on the electrodes Clean.

3. Insulation failure by insulator damage Replace.

4. Improper spark gap Adjust to

0.6～0.7 mm (0.023～0.028 in.).

Spark plug

5. Burn out of electrodes Replace.

1. Ignition coil inside failure Replace. Magneto

2. Damaged cable sheath Replace or repair.

1. Switch is OFF ON the switch.

2. Switch is failure Replace.

Switch

3. Primary wiring ground Repair.

Sparks appear in the spark plug.

1. Over sucking of fuel Drain excess fuel.

2. Too rich fuel Adjust carburetor.

3. Overflow Adjust or replace carburetor.

4. Clogging air cleaner Wash with mixed gasoline.

Compression and

fueling is normal

5. Incorrect fuel Change with proper fuel.

1. Worn out cylinder, piston, or piston ring Replace. Fueling normal but

poor compression 2. Gas leakage from cylinder and crank case gasket Apply liquid gasket and reassemble.

1. Choked breather air hole Clean.

2. Clogged carburetor Clean.

No fuel supply

3. Clogged fuel filter Replace fuel filter.

8-2 Engine stop during operation

Trouble Probable Cause Countermeasure

1. Switch is OFF ON the switch.

2. Plug cap disconnect Connect properly.

3. Short circuit by carbon deposited on the plug electrodes Clean.

4. Switch cord or high tension cord sheath worn out Replace.

5. Ignition coil inside failure Replace.

Suddenly stopped.

6. Engine seizure Overhaul and replace damaged parts.

1. Lack of fuel Refill.

2. Clogged carburetor Clean.

Gradual speed

reduction and

stopped. 3. Water mixed to fuel Drain and apply new fuel.

8-3 Engine cannot be stopped

Trouble Probable Cause Countermeasure

1. Lean fuel Adjust carburetor.

2. Cylinder fin clogged with dusts Clean.

3. Improper fuel Change with proper fuel.

4. Carbon deposited inside of combustion chamber Clean.

Overheating

5. Spark plug electrode red hot Clean thoroughly and adjust spark gap

to 0.6～0.7mm (0.023～0.028in.).

1. Faulty switch Replace. Switch

2. Cord failure Repair.

54

8. Troubleshooting

8-4 Lack of output power or unstable revolution

Trouble Probable Cause Countermeasure

1. Air is entering at fuel pipe joints, etc Secure connections.

2. Air is entering at intake tube joint or carburetor joint Replace gasket or tighten screws.

3. Water in fuel Replace with clean fuel.

4. Piston is starting to seize Filing of seized surface with fine files.

Compression is

normal and no misfire.

5. Muffler choked with carbon Clean.

1. Fuel too lean Adjust carburetor.

2. Clogging of cylinder fins with dust Clean.

3. Poor fuel quality Replace with clean fuel.

4. Carbon deposited in the combustion chamber Clean.

Overheating

5.Spark plug electrode red hot Clean thoroughly and adjust spark gap

to 0.6～0.7 mm (0.023～0.028 in.).

1. Dirty air cleaner Wash with mixed gasoline. Others

2. Over loading Reduce load.

8-5 The amount of the wind is weak

Trouble Probable Cause Countermeasure

1. The air cleaner element is clogged. Clean the element.

2. Carbon adheres to the spark arrester. Clean the spark arrestor.

Good compression

but cannot reach the

required revolutions at

full throttle 3. Carburetor is damaged. Maintenance or replace.

Printed in Japan 0901

SY – 015