FM136 Installation Manual !! Mighty Mule Wireless Intercom

Preview ! FM136-Mighty-Mule-Wireless-Intercom Nutone Lawn Mower Manuals - Lawn Mower Manuals – The Best Lawn Mower Manuals Collection

User Manual: !! Nutone Lawn Mower Manuals - Lawn Mower Manuals – The Best Lawn Mower Manuals Collection

Open the PDF directly: View PDF .
Page Count: 8

rev - 09-20-10

Crystal clear two-way wireless communication up to 500 feet

Wireless Gate Entry Intercom

Thank you for purchasing the Mighty Mule Wireless Gate Entry Intercom.

Please read the directions carefully and completely before installing.

Installation Instructions

GTO - Gates That Open, LLC • 3121 Hartseld Road • Tallahassee, Florida 32303

Telephone (850) 575-0176 • Fax (850) 575-8912 • www.mightymule.com

SAFETY NOTE:

NEVER install the keypad portion

of this system where a person can

reach through the gate to activate it,

or where a person can touch the gate

while activating the keypad.

The recommended minimum distance

between the gate and keypad is 10 ft.

IMPORTANT: Allow the

intercom base unit’s battery to

charge for 12 hours before using

the system for the rst time.

Keypad Unit

Base Unit

ACCESS CONTROLS

rev - 09-20-10

The Wireless Intercom/Keypad has two separate units: the KEYPAD and the BASE UNIT. The keypad should be mounted

outside the gate allowing visitors to press the CALL button from their vehicle. The base unit is powered by a rechargeable

battery; the charge is maintained by the transformer. It can also be disconnected from the transformer allowing it to go

anywhere within range for convenience. Up to three additional base units can be added for convenience in different

locations throughout the house.

When someone without an access code approaches the gate, they can press the CALL button on the keypad which will

ring the base unit inside the house. To answer the CALL, the person inside presses and holds the ANSWER button to

talk to the person at the gate, releasing the ANSWER button to listen. To allow the person calling to open the gate, the

GRANT PERMISSION button must be pressed. Then the person at the gate can press any number key on the keypad to

open the gate. The END CALL button terminates the calls and the ON/OFF switch can be used to conserve power when

using unit on battery (note: the base station will not recieve a signal if turned OFF).

Up to 25 different personal Entry Codes may be programmed into the keypad, allowing you to give different temporary

and permanent Entry Codes to different users. For example, you can give a delivery person their own temporary entry

code, which you can easily change after he has made the delivery. This will prevent him from being able to regain access,

while still allowing those to whom you gave permanent Entry Codes full access.

After entering a valid code, pressing any key on the keypad while the gate is opening will stop the gate; pressing any key

while the gate is stopped will cause the gate to reverse direction. The keypad will not affect the auto-close setting of your

gate opener system.

The keypad will light up and the unit will beep at the press of any key. The keypad memory will recognize your entry

code in a string of up to 20 digits. If it nds the correct sequence, it will activate the gate opener. As a security feature,

the keypad will shut down for 40 seconds if it does not nd the correct code sequence within a 20-digit string. This will

discourage an unauthorized person from trying to use random numbers to access your property.

Entry Codes will remain stored in memory even when the batteries go dead. The keypad will remember your Entry Codes

as long as you don’t press the RESET button.

FCC WARNING: Changes or modications to this unit not expressly approved by the party responsible for compliance could

void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15

of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in particular installations. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or more of the following measures: • Reorient or replace the receiver

antenna. • Increase the separation between the equipment and the receiver. • Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.

Features of the Wireless Intercom/Keypad

IMPORTANT: In areas of high radio frequency (RF) interference, the keypad may need to be connected (hard

wired) directly to the gate opener using 16 gauge (AWG) stranded, direct burial, low voltage wire (RB509, not

included).

The contents of all material available on this installation manual are copyrighted by Gates That Open, LLC (“GTO”), unless otherwise indicated. All rights are reserved by GTO, and

content may not be reproduced, downloaded, disseminated, published, or transferred in any form or by any means, except with the prior, written permission of GTO. Any reprinting of GTO

publications is by permission only. Copyright infringement is a violation of federal law.

GTO®, GTO/PRO®, Mighty Mule® are registered trademarks of GTO - Gates That Open, LLC. GTO Access Systems™ is a trademark of GTO - Gates That Open, LLC. These marks are the

exclusive property of GTO - Gates That Open, LLC (“GTO”). All rights are reserved by GTO, and these marks may not be used, in any form, without the prior, written permission of GTO.

rev - 09-20-10

Keypad Description

1. Install Batteries

Four (4) AA batteries (not included) are required to power the keypad. If an

external DC power supply such as the gate opener’s battery is used (see

2.B.“Hard-Wired Installation”), the AA batteries will act as a back up.

Step 1: Remove the two screws from the bottom of the keypad and separate

the keypad from its housing.

Step 2: Install four (4) AA batteries (not included).

1 2

ABC

DEF

GHI

JKL

MNO

PRS

TUV

WXY

CALL

STATUS

PROGRAM

CALLING GRANTED

STATUS Light:

This LED will blink once when any

key is pressed and provides visual

feedback when programming entry

codes.

GRANTED Light:

LED turns GREEN when access

permission is granted.

Keypad Front

Battery Holder:

Use 4 AA batteries.

RELAY

OUTPUT

AC/DC

POWER IN

123456789

–

ID SET

––

–+

–

RESET

JUMPER

ID SET button:

Used to reassign new code only when there is

another pair of GTO wireless intercom units

nearby causing interference.

DIP Switches:

Match the keypad dip switch settings with

your entry transmitter’s dip switch settings.

Relay output:

Used to connect the keypad to gate opener

control board in hard-wired applications.

Power Input:

Used to connect keypad to gate opener battery

for continuous power supply.

Keypad Interior

Knock-out

PROGRAM button:

Used to program entry codes.

CALLING Light:

LED is RED when calling and turns

GREEN when call is answered.

RESET button:

Pressing this button for 2 seconds will reprogram

the keypad to factory settings. All codes are

deleted. Default Master Code is “1234.”

ABC 3

DEF

GHI 5

JKL 6

MNO

PRS 8

TUV 9

WXY

CALL

STATUS

PROGRAM

CALLING GRANTED

123456789

–

1 2 3 4 5 6 7 8 9

ECE

A23S 12V

ALKALINE BATTERY

–

LED

2. Install Keypad

A. Wireless Installation

For wireless applications, the keypad must be in the line of sight of the gate opener

receiver and no more than 50 ft. away from the receiver. Always test the keypad

range before permanently mounting it. NOTE: a metal housing or metal object

could cause interference.

Step 1: Mount the keypad housing using the

screws provided.

Step 2: Set the keypad DIP switches to

match your entry transmitter’s DIP switch

settings.

NOTE: If you have not adjusted your gate opener’s entry transmitter from the factory setting,

see the “Personalize Transmitter Settings” section in the gate opener’s installation manual.

Then set the keypad DIP switches to match the entry transmitter DIP switch setting.

Step 3: Slide the keypad into the housing and secure with the small screws provided.

B. Hard-Wired Installation

To power the keypad with the gate opener’s battery and hard wire the communication between the

keypad and the gate opener, you will need to run two pairs of wires: one pair to hard-wire the keypad

to the gate opener’s control board; the other pair to connect the keypad to the gate opener’s battery.

Step 1: Turn the gate opener’s power switch OFF. Use two pairs of 16 gauge (AWG) stranded,

direct burial, low voltage wire (RB509) to connect the keypad to the gate opener control board and

battery. Run wire through PVC pipe from the ground to keypad and from the ground to the opener

control board to protect it from lawn mowers or grazing animals.

Determine how the wires will enter the keypad (e.g., from the back through a hole drilled in the post;

running the wire on the post surface). Remove the small rectangular knock-out on the back of the

keypad housing and pull the wires into the housing. Then mount the housing to the post using the

screws provided.

rev - 09-20-10

ALARM ACCESSORY RCVR

SEQ1

SEQ2 LEARN

BLU

ORG

WHT

GRN

R B G

Connect #1 wire from the

RELAY OUTPUT terminals

on the keypad to WHT

terminal on the gate opener

control board.

Connect #2 wire

from the RELAY OUTPUT

terminals on the keypad to the

GRN terminal on the gate

opener control board.

PRO-1000/2000, PRO-SL1000/SL2000 and Old Mighty Mule

Control Boards

RELAY

OUTPUT

AC/DC

POWER IN

123456789

–

Jumper ON

wireless mode

Jumper OFF

Hard-wire from Gate Opener

Power Supply from

Opener Battery

#1 #2

wired mode

Step 2: Strip 3/16" off the ends of one pair of low voltage wires. Attach the wires to the terminal

block marked RELAY OUTPUT on the keypad control board as shown. Connect the other

end of the wires to the gate opener’s control board as shown in Control Board Connections

(below).

Step 3: Strip 3/16" off the ends of the second pair of low voltage wires.

Attach the wires to the terminal block marked AC/DC POWER IN

on the keypad control board as shown. Connect the other end of

the wires to the opener’s battery: one end to the POSITIVE

(RED) pole and the other to the NEGATIVE (BLACK) pole.

Step 4: Connect the jumper between the two terminals on the

keypad control board (ON) as shown.

Step 5: Slide the keypad into the

housing and secure with the small

screws provided.

Step 6: Replace the control board cover

and turn the power switch ON.

ABC 3

DEF

GHI 5

JKL 6

MNO

PRS 8

TUV 9

WXY

CALL

STATUS

PROGRAM

CALLING GRANTED

Control Board Connections

If your control board doesn’t look like any of these diagrams, please refer to your gate opener

installation manual or call GTO Technical Service at 1-800-543-1236 or 850-575-4144.

GRN BLK RED

RECEIVER

COM COM

CYCLE

SAFETY

EXIT

OPEN

SHADOW

LOOP

EDGE

OPEN

EDGE

J11

J11 J8 J12

GTO/PRO DC Powered PRO-SW3000

and PRO-SW4000 Control Boards

Connect #1 wire from the

RELAY OUTPUT terminals on

the keypad to CYCLE terminal on

the gate opener control board.

Connect #2 wire from

the RELAY OUTPUT

terminals on the keypad

to the COM terminal on

the gate opener control

board. #1

RECR

GRN

BLK

RED

EXIT

SAFETY

EDGE

CYCLE

COMMON

LINK

Mighty Mule 350 Control Board

Connect #1 wire from the

RELAY OUTPUT terminals

on the keypad to CYCLE

terminal on the gate opener

control board.

Connect #2 wire from the RELAY

OUTPUT terminals on the keypad

to the COMMMON terminal on

the gate opener control board.

RECEIVER

COM COM

CYCLE

SAFETY

EXIT/

OPEN

SHADOW

LOOP

EDGE

OPEN

EDGE

BLKGRN RED

Mighty Mule 500 & 502

Control Boards

Connect the #1 wire from

RELAY OUTPUT terminals on the

keypad to the CYCLE terminal on

the opener control board.

Connect the #2 wire from

the RELAY OUTPUT

terminals on the keypad to

one of the COMMON

terminals on the opener

control board. #1

RECEIVER

ALM

GTO RCVR.

COM

GRN

BLK

RED

CYCLE

SAFETY

EXIT

SHADOW

OPEN

EDGE

COM

CONTROL INPUTS

EDGE

Connect #1 wire from

the RELAY OUTPUT terminals

on the keypad to CYCLE terminal

on the gate opener control board.

Connect #2 wire from the

RELAY OUTPUT terminals

on the keypad to the COM

terminal on the gate opener

control board. #1

GEN-3 (Blue) Control Boards

COM

GTO Inc.

SX4000 L

CYCLE

SAFETY

OPEN EDGE

RUN 2

OPEN

STOP

COM

SHADOW

LOOP

Connect #1 wire from the

RELAY OUTPUT

terminals on the keypad to

CYCLE terminal on the

gate opener control board.

Connect #2 wire from the

RELAY OUTPUT terminals

on the keypad to the COM

terminal on the gate opener

control board.

GTO/PRO GP-SL100 and GP-SW100

Control Boards

3. Test Keypad

Turn the gate opener power switch to ON. Test the keypad by entering “1234.”

rev - 09-20-10

4. Program the Keypad

Programming Interface/Keypad Operation:

• In these instructions, the symbol for the Programming

Button is:

• All codes are four (4) digits in length.

• Entry Code is a four (4) digit code needed to activate the

gate.

• Master Code is needed to add, remove or reset Entry Codes.

• Master Code also functions as an Entry Code.

• Factory default Master Code is “1234.”

• STATUS light should blink and keypad should beep (once)

whenever any button is pressed.

• If more than 10 seconds elapse between key presses, the

keypad returns to idle mode.

• Keypad can only enter program mode from idle mode.

• Keypad will beep three times before going into idle mode.

• When a programmed Entry Code is used, the keypad

STATUS light will blink twice and the keypad will beep

twice to conrm that a matched code is entered.

• No more than 20 key presses are allowed to obtain a

4-digit Entry Code. For example, “1234” is one of the

programmed Entry Codes. The user can enter “x1234” or

“xxxxxxxxxxxxxxxx1234” (with “x” being any key) and

the gate will be activated. If more than 20 key presses are

entered without matching one of the Entry Codes, then the

STATUS light will ash rapidly and the keypad will go into

“lock-down” mode for 40 seconds. The user must not enter

any code for at least 40 seconds before the unit returns to

idle mode.

Program New Master Code:

1. Press and release PROGRAM button.

2. Enter the old Master Code, then press and release

PROGRAM button.

3. Enter “06” then press and release PROGRAM button.

4. Enter the new Master Code, then press and release

PROGRAM button.

5. Enter the new Master Code again for conrmation, then

press and release PROGRAM button.

6. Keypad beeps 3 times to conrm that the new Master Code

is accepted. NOTE: If the new Master Code is not a matched

pair or an error occurs (e.g., if the entry code is NOT a

4-digit code), the STATUS light will ash rapidly and the

keypad will beep for 2 seconds before returning to idle mode

with old Master Code.

Example: Key press sequence to change Master Code from

“1234” to “3121.”

1 2 3 4 0 6 3 1 2 1 3 1 2 1

Add New Entry Code:

1. Press and release PROGRAM button.

2. Enter the Master Code, then press and release PROGRAM

button.

3. Enter “02” then press and release PROGRAM button.*

4. Enter the new Entry Code, then press and release

PROGRAM button. The keypad will beep 3 times to conrm

that the new Entry Code is accepted. **

Example: Key press sequence to add “3456” as a new entry

code (“1234” is the Master Code).

1 2 3 4 0 2 3 4 5 6

Add Temporary Entry Code:

1. Press and release PROGRAM button.

2. Enter the Master Code then press and release PROGRAM

button.

3. Enter “8” and any number between 1 thru 7 then press and

release the PROGRAM button. The second number (1 thru

7) indicates the number of days after which the code will be

automatically removed from memory.*

4. Enter the new Entry Code then press and release PROGRAM

button. The keypad will beep 3 times to conrm that the new

Entry Code is accepted.**

Example: Key press sequence to add “3456” as a temporary

Entry Code that will remain valid for only three days

(“1234” is the Master Code).

1 2 3 4 8 3 3 4 5 6

Delete An Entry Code:

1. Press and release PROGRAM button.

2. Enter the Master Code then press and release PROGRAM

button.

3. Enter “03” then press and release PROGRAM button.

5. Enter the Entry Code to be deleted, then press and release

PROGRAM button. The keypad will beep 3 times to conrm

that the Entry Code is deleted. NOTE: If no matching code is

found or the code is NOT 4-digit in length, then an error has

occurred. The STATUS light will ash rapidly and the keypad

will beep for 2 seconds before returning to idle without

saving.

Example: Key press sequence to delete entry code “3456”

from memory (“1234” is the Master Code).

1 2 3 4 0 3 3 4 5 6

Delete ALL Entry Codes:

1. Press and release PROGRAM button.

2. Enter the Master Code then press and release PROGRAM

button.

3. Enter “07” then press and release PROGRAM button. The

keypad will beep 3 times to conrm that all Entry Codes are

deleted.

Example: Key press sequence to delete all entry codes from

memory (“1234” is the Master Code).

1 2 3 4 0 7

*NOTE: If memory is full (there are already 25

programmed Entry Codes) the STATUS light

will ash rapidly and the Keypad will beep

for 2 seconds before returning to idle mode

without saving.

**NOTE: If the code is NOT 4-digits in length or

an error has occurred, the STATUS light will

ash rapidly and the keypad will beep for 2

seconds before returning to idle mode without

saving.

rev - 09-20-10

Base Unit Description

GRANT ACCESS Button:

Must be pressed before the person at the keypad can press any key to open the gate.

Base Unit Face

PUSH TO ANSWER/TALK Button:

Use to answer CALL from keypad. PRESS and HOLD to talk; RELEASE to listen.

POWER

Keypad

Batt Low

Grant Permission

Push To Answer/Talk

End Call

DV 9V

POWER Light:

GREEN: charging; RED: battery power mode (unplugged from transformer); Blinking RED: low battery.

KEYPAD BATTERY INDICATOR Light:

LED turns ON when keypad battery is low.

9 Vdc Transformer Plug:

Connect transformer here to charge the base unit battery.

ID SET

VOLUME

POWER

OFF ON

ON/OFF Switch:

Turn OFF to conserve power when battery operated.

VOLUME Control:

Controls volume level of speaker.

ID SET button:

Used only to reassign new ID code (links base to keypad).

END CALL Button:

Allows user to terminate the call.

BATTERY ACCESS Cover:

Rechargable 3.6 Volt Ni-MH battery (included).

5. Install Base Unit Battery

Step 1: Remove the battery access cover using a small phillips head

screwdriver.

Step 2: Plug the rechargeable Ni-MH battery into the receptacle

inside the battery compartment.

Step 3: Replace the battery access cover.

6. Connect the Transformer

Step 1: Find a convenient location near an outlet to mount or place the

base unit. If you are mounting the base unit on the wall, use the template

(page 6) to place screws.

Step 2: Plug the transformer

into the AC outlet and

connect it to the base unit’s

power jack marked DC 9V.

ID SET

Battery Plug

Battery

POWER

Keypad

Batt Low

Grant Permission

Push To Answer/Talk

End Call

DV 9V

Transformer

110 Vac outlet

IMPORTANT: Allow the base

unit’s battery to charge for 12

hours before using the system

for the ﬁrst time.

Base Unit Bottom

rev - 09-20-10

The base unit can be disconnected from the transformer for use in another location. The battery will last approximately

four (4) hours when unplugged from the transformer. IMPORTANT: You can turn the base unit OFF to conserve

battery power, however it will not receive a signal when OFF.

7. Add Additional Base Units (optional)

If you have purchased additional base units (F3101MBC) to enhance your system, each additional unit’s

ID Code must be programmed into the keypad so they can communicate.

Step 1: Install the battery and turn the base unit ON.

Step 2: Press and release the “ID SET” button on the keypad.

Step 3: Press the number on the keypad that corresponds to the base unit

you are adding. You will hear a number of beeps corresponding to the

number you pressed. For Example: if you are adding a second base unit to

the system, PRESS “2,” the keypad will beep TWO times.

Step 4: Press the “ID SET” button on the base unit for approximately two

seconds then release. You will hear TWO beeps from the base unit and

TWO beeps from the keypad, which means the ID Code is set.

IMPORTANT: Base units need to be placed at least 10 feet apart to

prevent interference.

8. Test the System

IMPORTANT: The base unit and the keypad cannot be within 30 feet of

each other when operating. If units are closer than 30 feet the signal will be

inconsistent and emit speaker feedback. Also, multiple base units must be

no closer than 10 feet from each other to prevent interference.

Have someone press the CALL button on the keypad at the gate. When

the base unit inside the house rings, press the ANSWER button and talk to

the person at the gate to check the connection and range. Then press the

GRANT PERMISSION button and have the person at the gate press any

key on the keypad to activate the gate.

Troubleshooting

Make sure all connections are secure and correct, batteries installed, and base

unit is ON. If you have multiple base units, they should be at least 10 feet apart

to prevent interference.

In rare cases, other devices operating in the same frequency band may cause

interference with the intercom signal. If the system does not communicate at all,

reassign the base unit/keypad ID code as follows (this will require two people):

1. Open the keypad and locate the “ID SET” button above the batteries. Locate

the “ID SET” button on the bottom of the intercom base unit.

2. Make sure the “antenna-to-antenna” distance between the keypad and the

RELAY

OUTPUT

AC/DC

POWER IN

123456789

–

ID SET

––

–+

–

RESET

JUMPER

ID SET button

ID SET

VOLUME

POWER

OFF ON

Keypad - Inside

Base Unit – Bottom

1 2

ABC

DEF

GHI

JKL

MNO

PRS

TUV

WXY

CALL

STATUS

PROGRAM

CALLING GRANTED

Keypad - Front

ID SET button

Intercom ID Codes

The keypad and base unit are programmed at the factory to

communicate with each other, and do not need the ID Codes

programmed. This base unit is the MASTER or #1 unit.

RELAY

OUTPUT

AC/DC

POWER IN

123456789

–

ID SET

––

–+

–

RESET

JUMPER

ID SET buttons

ID SET

VOLUME

POWER

OFF ON

Keypad (inside)

Base unit (bottom)

rev - 09-20-10

base unit is at least 30 feet.

3. Press the “ID SET” button on the keypad until you hear a beep, then release. This erases all stored ID Codes.

4. Press the “ID SET” button on the MASTER base unit for approximately 2 seconds then release. You will hear ONE

beep from the base unit and TWO from the keypad, which means the ID Codes are reassigned.

5. Test the system by pressing the CALL button on the keypad to see if the base unit receives the signal. Once the system

is working, you will need to reset additional base stations (see page 5).

If all connections are correct and the ID SET change didn’t solve the communication problem, please call our Technical

Service Department at 1-800-543-1236, Monday–Friday, 8:00 am to 7:00 p.m. (ET).

INTERCOM/KEYPAD SPECIFICATIONS

Frequency 318 MHz from keypad to gate opener

900 MHz from keypad to base station

Memory – Keypad Stores up to 25 four-digit entry codes

Power Consumption – Keypad 60 mA when relay is closed

Power Supply – Keypad 8-24 Vdc or four AA batteries

Power Supply – Base Unit 9 Vdc 300 ma transformer; 3.6V Ni-MH 800 mA

rechargeable battery pack

Range from Keypad to Base Unit 500’ wireless

Range from Reypad to Gate Opener 50’ wireless 100’ wired using 16 AWG wire

Relay Output – Keypad Momentary, normally open dry contact closes for 2

seconds upon activation

Relay Output Rating – Keypad 12 or 24 Vdc 100 mA

Wiring – Keypad Power & Relay Output 16 AWG stranded low voltage direct burial wire

Limited One Year Warranty

Gates That Open, LLC (“GTO”). gate opener accessories are warranted by the manufacturer against defects in workmanship for a period of one (1) year from the date of

purchase, provided recommended installation procedures have been followed.

In the case of product failure due to defective material or manufacturer workmanship within the one (1) year warranty period, the accessory will be repaired or replaced

(at the manufacturer’s option) at no charge to the customer, if returned freight prepaid to GTO - Gates That Open, LLC • 3121 Hartseld Rd. • Tallahassee, FL 32303.

IMPORTANT: Call 850/575-4144 or fax 850/575-8950 for a Return Goods Authorization (RGA) number before returning goods to factory. Products received at

the factory without an RGA will not be accepted. Replacement or repaired parts are covered by this warranty for the remainder of the one (1) year warranty period. GTO

will pay the shipping charges for return to the owner of items repaired.

The manufacturer will not be responsible for any charges or damages incurred in the removal of the defective parts for repair, or for the reinstallation of those parts after

repair. This warranty shall be considered void if damage to the product(s) was due to improper installation or use, connection to an improper power source, tampering, or

if damage was caused by lightning, electrical power surge, wind, re, ood, insects, or other natural agent.

After the one (1) year warranty period, GTO or one of its authorized service centers will make any necessary repairs for a nominal fee. Call GTO at 850/575-4144 for more

information. This warranty gives you specic legal rights, and you may also have other rights which may vary from state to state. This warranty is in lieu of all other war-

ranties, expressed or implied. NOTE: Verication of the warranty period requires copies of receipts or other proof of purchase. Please retain those records.

If you have any questions or concerns, please contact our Technical Service Department

Monday thru Friday 8:00 a.m. to 7:00 p.m. (ET) at 1-800-543-1236 or 850-575-4144

GTO–Gates That Open, LLC • 3121 Hartseld Road • Tallahassee, Florida 32303

Telephone (850) 575-0176 • Fax (850) 575-8912 • www.gtoinc.com

Hole Template for Mounting the Base Unit

FM136 Installation Manual !! Mighty Mule Wireless Intercom

Preview ! FM136-Mighty-Mule-Wireless-Intercom Nutone Lawn Mower Manuals - Lawn Mower Manuals – The Best Lawn Mower Manuals Collection

Navigation menu

Versions of this User Manual:

Views

Navigation