Roland Fantom S Factory Reset
Roland Corporation MC-303 Factory Reset Procedures Factory_Reset Roland Corporation - MC-303 - Factory Reset Procedures
User Manual: Fantom-S
Open the PDF directly: View PDF 
.
Page Count: 10
| Download | |
| Open PDF In Browser | View PDF |
® R Factory Reset Procedures Caution: Many of these procedures will erase all memory in the unit. Make sure you have backed up any data you wish to keep before performing these procedures! If a unit is not listed here, it does not have an initialization procedure that is user-executable. A Model A-30/33/37 A-50/80 A-70/90/90EX A-220 A-300PRO A-500PRO A-500S A-800PRO A-880 AD-8 AP-700 AT-Series AX-09 AX-1/7 AXIS-1 AX-Synth B Model BR-8/532/1180 BR-600 BR-800 BR-864 BR-900CD/ 1200CD BR-1600CD C Model CD-2 CD-2E/2i CDX-1 CE-20 CR-80 D Model D-2 DB-30 DB-60 DB-88 DB-90 DD-20 Procedure Power on while holding WRITE. (Hold for 15 seconds) While holding the first, third, and fourth buttons under the display, press CHANNEL. Then press any cursor button Power on while holding down MANUAL, then press ENTER Power on while holding B and MEMORY Hold ACT and <, use the VALUE dial to select “FACTORY RESET.” Press ENTER twice. Hold ACT and <, use the VALUE dial to select “FACTORY RESET.” Press ENTER twice. Hold MIDI CH and PGM CHANGE, press the SYSTEM key, Use the VALUE dial to select “SY6,” press ENTER 3 times. Hold ACT and <, use the VALUE dial to select “FACTORY RESET.” Press ENTER twice. Power on while holding SIGNAL and MEMORY Power on while holding WRITE. Confirm that “F” flashes in the display, then release WRITE. Press WRITE again Power on, then press EXIT repeatedly to get ANALYZER/FILTER screen. Cursor to MENU, press ENTER. Cursor to SYSTEM, press ENTER. Cursor to INITIALIZE, press ENTER. Use VALUE to select ALL MEMORY, then press ENTER twice (Make sure disk drive is empty.) Power on while holding ONE TOUCH PROGRAM Power on while holding FAVORITE A, B, and WRITE. Press TONE 5, then press WRITE. Power on while holding WRITE. (Hold for 30 seconds) While holding FUNCTION, press the F#0, C#2, and D#2 keys Power on while holding INC/+, DEC/-, and TONE 7(ORGAN/CLAVI), then press WRITE. Procedure Press UTILITY. Cursor to “Initialize.” Press ENTER. Cursor to “All.” Press ENTER twice Power on while holding GUITAR, MIC, and LINE. Press ENTER. Press MENU. Cursor to “Factory Reset.” Press ENTER three times. Power on while holding INPUT SELECT/GUITAR/BASS, MIC, and LINE. Press ENTER Press UTILITY. Press CURSOR Right to select “Initialize.” Press ENTER. Press CURSOR Right to select “All.” Press ENTER twice Press UTILITY. Cursor to “Initialize.” Press ENTER. Cursor to “All.” Press ENTER twice Procedure Press MENU. Use the DATA dial to select “INITIALIZE.” Press ENTER twice. Press MENU. Use the < / > buttons to select “Factory Reset.” Press ENTER twice. Press UTILITY. Cursor right to “INIT”. Press ENTER/YES. Use CURSOR buttons to select desired target to be initilaized, (GLOBAL, FX, MIXER, ALL). Press ENTER/YES twice Power on while holding WRITE. Release WRITE then press WRITE again Power on while holding DEL and REPEAT, then press ENTER Procedure With the unit on, Hold WRITE and press SYSTEM. Press ENTER twice Power on while holding the START/STOP button until “F” shows in the display Power on while holding the MEMORY button until “F” shows in the display Power on while holding METRONOME MODE and LOOP MODE. Press WRITE Power on while holding MEMORY Power on while holding WRITE. Release, then press WRITE again ©2010 Roland Corporation U.S. Page 1 ® R DDR-30 DEP-3/5 DJ-70/70MKII DR-3 DR-5 DR-202 DR-550/550MKII DR-660 DR-670 DR-770 DR-880 DS-330 E Model E-09 E-10/20/30 E-35 E-36 E-50/60/80 E-56 E-66 E-68/70/86/96 E-300/500 E-600 EG-101 EM-10 EM-15/25 EM-20/30/50/55 EM-2000 ep-5/7/7MKII ep-9 ep-75/85 EQ-20 EXR-3/5 EXR-40/46OR F Model F-110 Fantom Fantom-G6/7/8 Factory Reset Procedures Power on while holding the #1 button Power on while holding MEMORY NO UP (^) and DOWN (v) Power on while holding the UP ARROW button to enter test mode. Press A, press C, press S1. When finished the screen will display IC21 = OK Press EDIT. CURSOR Right to select “SYSTEM.” Press ENTER. CURSOR Right to select. Press ENTER twice Power on while holding FRET LEFT (<) and RIGHT (>), then press ENTER twice Power on while holding MUTE and ROLL. Press TAP/ENTER. Cursor to “YES” in the display. Press TAP/ENTER Power on while holding -1 and +1, then press START Press UTILITY, then use LEFT (<) and RIGHT (>) to select [8] INIT. Press ENTER twice Power on while holding REC and STOP / CONT. Press ENTER twice Press UTILITY, then use LEFT (<) and RIGHT (>) to select [9] F. RST. Press ENTER twice Press EDIT. Press CURSOR Right to select “Factory Reset.” Press ENTER twice Power on while holding REVERB and SPLIT, then press YES Procedure Press FUNCTION so it is lit. Use the FAMILY buttons to select “Utility,” then use the SELECT buttons to select “Factory Reset.” Press TEMPO >/YES twice Power on while holding WRITE Power on while holding REC/PUNCH IN Power on while holding RECORDER Press MENU. Press “UTILITY” then press “FACTORY RESET.” Press “EXECUTE.” Power on while holding WRITE Power on while holding REC in the DISK RECORDER section Power on while holding WRITE Press UTILITY. Use the buttons under the display that correspond to < > to select FACTORY PRESET. Press EXECUTE, then press OK. When the screen displays RESET COMPLETE, turn the unit off, then on Press FUNCTION and use the PAGE (<) (>) buttons to select “Factory Preset.” Touch the “Execute” icon followed by the “OK” icon on the display screen. Power off then on Power on while holding WRITE Power on while holding USER PROGRAM/WRITE With the unit on, press FUNCTION until “RESUME” shows in the display. Then press TEMPO+ Power on while holding USER PROGRAM/WRITE Performance Sets need to be loaded from disk to restore factory default settings. Insert the factory ZIP Disk into the drive and power on. Press F5 (Disk), then F1 (Load). Press PAGE ^ / v to select “PRF MEM” and press UPPER 1(Execute) While holding REC and PLAY, press STRINGS. Power off and then back on While holding REC and PLAY, press CHOIR. Power off and then back on Power on while holding REC Power on holding LIGHT and SELECT. Release, then press LIGHT and SELECT again Power on while holding USER PROGRAM/WRITE Power on while holding USER PROGRAM/WRITE Procedure Hold REVERB and press TRANSPOSE, hold OTHERS and use the +/- buttons to select “Fct” in the display. Press the Stop/Start button twice. With the unit on, press MENU. Press the UP or DOWN cursor buttons to select FACTORY RESET. Press 8 (EXECUTE) twice Press MENU. Use the CURSOR Up and Down buttons to select “Factory Reset,” then press F8 [Select] followed by F7 [OK]. Press F7 [OK] when completed. ©2010 Roland Corporation U.S. Page 2 ® R Fantom-S/S88 Fantom-Xa Fantom-XR Fantom-X6/7/8 FC-100MKII FC-200 FG-10/1000 FP-2 FP-4 FP-5 FP-7 FP-8 FR-3 FR-5/7 Factory Reset Procedures Press MENU. Use the CURSOR Up or Down buttons to select “Utility,” then press ENTER. Press 3 (Factory Reset) Press 8 (Execute) Press EXIT. Press MENU. Turn the VALUE dial to select “Utility” and then press ENTER. Press F3. Press F6 Press MENU. Press CURSOR Down to select “UTILITY.” Press ENTER. Press CURSOR Down to select “FACTORY RESET.” Press ENTER twice Press MENU. Press the CURSOR DOWN button to select “Utility.” Press button 3 (Factory Reset). Press Button 8 (Exec). Cycle the power Power on while holding pedals #1, #2, and #8 Power on while holding the #10 pedal, then press the CTL pedal Power on while holding CLEAR and EXIT Power on while holding REVERB until “Fct” shows in the display Power on while holding FUNCTION Power on while holding PEDAL CONTROL Power on while holding FUNCTION Press FUNC and release. While holding PIANO, press FUNC again Power on while holding SET and ORCHESTRA. Power on while holding MENU/WRITE. Press the DATA/ENTER button G Model G-70 G-600/800 G-1000 GI-10 GI-20 GM-70 GP-16 GP-20 GP-100 GR-09 GR-1 GR-20 GR-30 GR-33 GS-10 GT-3 GT-5 GT-6/8/Pro GT-6B GT-10/10B GW-7 GW-8 GX-700 Procedure Press MENU. Touch UTILITY, then touch FACTORY RESET. Touch EXECUTE Power on while holding WRITE Performance Sets need to be loaded from disk to restore factory default settings. Insert the factory ZIP Disk into the drive and power on. Press F5 (Disk), then F1 (Load). Press PAGE ^ / v to select “PRF MEM” and press UPPER 1 (Execute) Power on while holding PARAMETER + and -, then press VALUE + With the power off, set the GUITAR /BASS switch to match the instrument you are using. Power on while holding TUNER(STRING SEL). Press WRITE Poly Mode: Power on while holding PLAY, GENERAL EDIT, and IND EDIT. Mono Mode: Power on while holding TUNE, CONTROL ASSIGN, and DATA TRANSFER Power on while holding the #6, #7, and #8 buttons. Use the FUNCTION LEFT (<) and RIGHT (>) buttons to select “2.All Factory Preset,” then press WRITE three times Power on while holding WRITE. Release WRITE, (The MEMORY indicator will flash), then press WRITE again Power on while pressing in the PARAMETER knob, then press WRITE Power on while holding Pedal #2, then press the VALUE + button. Now press EDIT/PLAY Power on while holding WRITE/COPY, then press YES Power on while holding WRITE, then press WRITE again Power on while holding Pedal #2, then press the PATCH+ button to select INI. Press EDIT/PLAY. Then press PATCH+ and PATCH- simultaneously Press SYSTEM. Press PARAMETER (>) right to select “FACTORY RESET”. Use VALUE to select “ALL”. Press WRITE twice Power on while holding the CHANNEL SELECT A and B buttons (within the PREAMP/SPEAKER section), then press WRITE Power on while holding MOD and SFX. Press WRITE Power on while holding MOD and FEEDBACKER/SLOW GEAR. Press WRITE Power on while holding the PREAMP ON/OFF and (PREAMP)TYPE/VARIATION buttons. Press WRITE Power on while holding COMP/LIMITER ON/OFF and TYPE VARIATION. Press WRITE Press SYSTEM. CURSOR right to select “FACTORY RESET” then press ENTER twice. Press FUNCTION. Press SELECT Left or Right to choose “Utility.” Press ENTER twice Press MENU. Use the CURSOR Up and Down buttons to select “Utility” then press ENTER. Use the CURSOR buttons to select “Factory Reset” then press ENTER twice. Power off and on. Press TUNER/UTILITY. Use PARAMETER LEFT (<) and RIGHT (>) buttons to select FACT ©2010 Roland Corporation U.S. Page 3 ® R Factory Reset Procedures INIT. Cursor to left and dial SYSTEM, then right and dial P#100. Press WRITE, then TUNER/UTILITY H Model HP-130 HP-557 HPD-10 HPD-15 Procedure Power on while holding REC Press GUIDE button until it is NOT lit. Touch PIANO, then touch FUNCTION. Use Page (<) (>) to select the function page. Touch FACTORY RESET. Touch OK While holding SHIFT, press EDIT. Press the V button until you see “FACTORY RESET.” Press >, then use the +/- buttons to select “ALL.” Press V, then press 4/OK Press SYSTEM and use the PARAMETER (>) to select “FACTORY RESET SYSTEM.” Use the VALUE dial to select “ALL” and press WRITE J Model JD-800 JD-990 JP-8000 JP-8080 JS-30 JS-5 Juno-D Juno-Di Juno-G Juno-Gi Juno-Stage JV-30 JV-35/50 JV-80/90 JV-880 JV-1000 JV-1010 JV-1080 JV-2080 JW-50 JX-1 JX-305 K Model KF-90 KR-5/7 Procedure Press DATA TRANSFER. Use PAGE UP (^) and DOWN (v) to select FACTORY PRESET. Press YES While holding EXIT, press UTILITY. Press F6 (EXECUTE), then F5 (YES) While holding SHIFT, press INIT/UTIL. Press INIT/UTIL repeatedly to select INITIALIZE WRITE. Use the DOWN/UP buttons to select FACTORY PRESET, then press WRITE Press EDIT. Press INIT/UTIL (Bank 7) repeatedly to select Factory Reset. Press REC then press WRITE Power on while holding RECORD located in the SEQUENCER section Press UTILITY. Use CURSOR buttons to select “16 SYSTEM FACTORY RESET.” Press ENTER twice Press MENU. Press PAGE/CURSOR Right to select “Factory Reset”. Press ENTER twice Press MENU. Use ^/v to select “UTILITY” then press ENTER. ^/v to select “FACTORY RESET” then press ENTER twice. Press MENU. Use ^/v to select UTILITY then press ENTER. Press F3 FACTORY then press F6 EXECUTE. Press MENU. Use the VALUE Dial to select “5. Utility” then press ENTER. Use the VALUE Dial to select “Factory Reset” then press ENTER. Press Button 5 [EXEC]. Press MENU. Use the CURSOR buttons to select “UTILITY,” then press ENTER. Use the CURSOR buttons to select “FACTORY RESET,” then press ENTER. Press 7 [EXEC] to confirm. Power off then back on when finished. Press CHORUS and REVERB (above INITIALIZE) simultaneously. Press VALUE UP (^) Press CONTROL and MASTER simultaneously. Use PARAMETER UP (^) and DOWN (v) to select ALL. Press VALUE UP (^) Power on while holding NUMBER 8 (also labeled PERFORM 16 and CAPS). Press ENTER and then press WRITE Press UTILITY, then use the DATA dial to select FACTORY PRESET. Press ENTER twice Power on while holding NUMBER 8 (also labeled PERFORM 16 and CAPS). Press ENTER, then press WRITE Press VALUE to select Performance Mode. While holding VOLUME press VALUE. Use the CATEGORY/BANK dial to select Piano (LCD will display Fct). Press VALUE twice Press UTILITY. Cursor down once, then cursor right three times to select FACTORY PRESET. Press ENTER twice, then press UTILITY Press UTILITY. Press F6 twice to select MENU 3. Press F1. Then press F6. If necessary, use the VALUE DIAL to turn Memory Protect OFF and press F6 twice Press TUNE/FUNCTION. Press F5 (FACTORY), then F4 (JW RESET), then F3 (GS RESET), then F4 (YES) Power on while holding WRITE and FLUTE Press UTILITY. Use PAGE to select Factory Preset and press ENTER. Use PAGE to select ALL and press ENTER twice Procedure Press FUNCTION. Touch [System Setting]. Touch [Facotry Reset]. Touch [Execute Press the One Touch Program PIANO button. Touch FUNCTIONS. Touch FACTORY RESET ©2010 Roland Corporation U.S. Page 4 ® R KR-15/15M KR-55 KR-75 KR-177 KR-277/375 KR-350 KR-377 KR-500 KR-570 KR-575 KR-577/977 KR-650 KR-770 KR-1070 KR-1077 KR-3000 KR-3500/4500 KR-4700/5000 KR-5500 L Model LVC-1N M Model M-10/16DX M-660/760 M-1000 M-BD1/DC1 M-GS64/OC1 M-SE1/VS1 MC-09 MC-303 MC-307 MC-505 MC-808 MC-909 Factory Reset Procedures Press the One Touch PIANO button. Touch FUNCTION SETTINGS. Touch FACTORY RESET. Touch EXECUTE. Touch YES Hold MIDI/FUNC and press CARD. Hold both VARIATION buttons for 5 seconds Press UTILITY and use the PAGE <> buttons to select “Factory Preset.” Press EXECUTE, then press OK In the Utility menu screen, press PAGE < (left) or PAGE >(right) to select the “FACTORY PRESET” page. Press EXECUTE. Press OK Press FUNCTION until it is lit. Use BEAT and TEMPO buttons to display “FNC41”. Press TRANSPOSE twice While holding LOAD and SAVE, press WRITE Press FUNCTION until it is lit. Use the PAGE left or PAGE right buttons at the bottom of the display until “Factory Reset” appears. Press “FACTORY RESET” next to the display. Press EXECUTE at the bottom of the display. Press OK While holding FROM and TO, press WRITE While holding PART VOLUME ACCOMP, press TRACK 2 and 4 buttons (Composer section) simultaneously. Press PART VOLUME ACCOMP repeatedly to get FACTORY SETUP LOAD in the window. After loading is complete, power off and then back on Press FUNCTION and use the PAGE left or right buttons to select “Factory Preset.” Touch the “Execute” icon followed by the “OK” icon on the display screen. Power off then on Press FUNCTION until it is lit. Touch [Factory Reset]. Touch [Execute]. Touch [OK] While holding LOAD and SAVE, press WRITE While holding PART VOLUME ACCOMP, press TRACK 2 and 4 buttons (Composer section) simultaneously. Press PART VOLUME ACCOMP repeatedly to get FACTORY SETUP LOAD in the window. After loading is complete, power off and then back on Press UTILITY and use the PAGE <> buttons to select “Factory Preset.” Press EXECUTE, then press OK Press FUNCTION until it is lit. Touch [Factory Reset]. Touch [Execute]. Touch [OK] While holding FROM and TO, press WRITE While holding LOAD and SAVE, press WRITE While holding EDIT, press LOAD and SAVE While holding LOAD and SAVE, press WRITE Procedure Power on while holding ENTER Procedure Power on while holding FINALIZE and ROOM ACOUSTIC While holding EDIT, press WRITE. Use PARAMETER UP (^) and DOWN (v) to select ALL, then press WRITE. When completed, press EDIT to return to Play Mode Set the SELECT switch to the OPTICAL Input setting, then power on while holding the CLOCK SOURCE button Power on while holding F3 Power on while holding F3 Power on while holding F3 Press SETUP. Press INC or DEC until “Fct” shows in the display. Press ENTER, then press WRITE Power on while holding down SHIFT, then press ENTER With unit on, Press SYSTEM. Press F2 UTIL. Press CURSOR DOWN until “Factory Reset” appears. Press F1. Press F4 Power on while holding down SHIFT, then press ENTER. Note, this procedure takes several minutes Press SYSTEM, then hold SHIFT and press keyboard pad 16. CURSOR to “Factory Rest” and press ENTER twice. With the unit on, press MENU. Use CURSOR to select “Utility.” Press ENTER. Press F4 (Factory Reset.) Press F6 (Execute) ©2010 Roland Corporation U.S. Page 5 ® R ME-5 ME-6/6B ME-8/8B ME-10 ME-20/20B ME-25 ME-30 ME-33 ME-50/50B ME-70 ME-X MICRO BR MK-80 MKS-50 MMP-2 MT-32 MT-90S MT-100 MT-120/120S MT-200 MT-300S MV-8000/8800 Factory Reset Procedures Power on while holding pedals #1 and #2, then press WRITE immediately Power on while holding PARAMETER DOWN (v) and LEFT (<), then press WRITE Power on while holding PARAMETER LEFT (<) and DOWN (v), then press WRITE/COPY Power on while holding the BANK DOWN (v) pedal, then press WRITE In Manual Mode, hold EDIT/EXIT and press PEDAL 2. Press WRITE twice. Hold EXIT and press the MEMORY v (down) pedal. Press WRITE twice. Power on while holding PARAMETER RIGHT (>) and VALUE DOWN (-), then press WRITE/COPY Power on while holding the AMP/EFFECT right button and EZ TONE. Release, then press WRITE and wait for “WRITE” to stop flashing in the LCD. Power off, then on again Power on while holding WRITE and BANK Left <, then Press WRITE Twice Press Pedals 3 & 4 at the same time to switch to Manual Mode. Hold down EDIT / EXIT and press the MOD pedal. Press WRITE twice. Power on while holding PARAMETER DOWN (v) and LEFT (<), then press WRITE Power on while holding UTILITY. Press YES twice. While holding WRITE, press EDIT. While holding the LEFT (<) and RIGHT (>) cursor buttons, press UP (^) Poly Mode: Power on while holding NUMBER 4 and 8. Mono Mode: Power on while holding NUMBER 3 and 7 With the unit on press SYSTEM until it is orange. Press PAGE until “INITIALIZE” appears. Use the left VALUE control to select the desired target to be initialized. (SYSTEM, USER PATCHES, ALL). Press ENTER twice While holding MASTER VOLUME, press RHYTHM PART. Press PART 1 With the unit on, Press SONG and [4]. Press <(Bwd) or >(Fwd) until “Factory Reset” is displayed. Press (+). Press > (PLAY). Turn off the power, then on again While holding STOP, press DELETE. After the display flashes ALL CLEAR, press EXECUTE Power on while holding REPEAT, SONG (blue button), and PLAY. Press FWD repeatedly, until the window reads T-13. Press PLAY, then press REC. Power off, then on Power on while holding REPEAT, SONG (blue button), and PLAY. Use the DIAL to select T-15 in the window. Press PLAY, then press REC. Power off, then on Press MENU and use the VALUE DIAL to select “13:Factory Prset”. Press ENTER/TRANSPOSE twice. Power off then on Press SYSTEM, press F5 (SysInfo), press F3 (Initialize), press F5 (Yes). Please note that all factory patches need to be reinstalled via CD-ROM. P Model P-55 Pad-8 Pad-80 PC-150 PC-200/200MKII PCR-30/50/80 PCR-M30/50/80 PCR-300/500/800 PK-5 PM-16 PMA-5 Prelude Pro-E PW-10 Procedure Power on while holding both INSTRUMENT buttons, then press PARAM 1 Power on while holding MIDI CH and NOTE NUMBER. Power off, then back on Power on while holding both VALUE (solid < and >) buttons Power on while holding COMMAND on the left edge of the keyboard Power on while holding the two buttons under the word STANDARD Press EDIT. Press the SYSTEM key, then press the # 8 key. “SY8” will show in the display. Press ENTER three times Press EDIT. Press the SYSTEM key, then press the # 8 key. “SY8” will show in the display. Press ENTER three times Press EDIT. Use the VALUE knob to select “SYS,” then press ENTER. Use the VALUE knob to select “SY16,” then press ENTER. Press ENTER twice. Power on while holding OCT/PARAM Power on while holding NUMBER buttons 1 and 2. (This reloads the first BANK of settings) Press UTILITY, then press the RIGHT (>) cursor button repeatedly to select INITIALIZE. Press ENTER, then [EXEC] Press MENU. Use the ^/v buttons to select “Utility” then press ENTER. Use the Cursor buttons to select “Factory Reset” then press ENTER. Power on while holding WRITE With the unit off, turn the TYPE knob to “VO-WAH”. Power on while holding ©2010 Roland Corporation U.S. Page 6 ® R Factory Reset Procedures MANUAL/MEMORY. (ON/OFF will blink three times, then the MEMORY indicator blinks). Release MANUAL/MEMORY, then press MANUAL/MEMORY again R Model R-09/HR R-5/8/8MKII R-8M R-70 RA-50/90 RA-95 RA-800 RC-50 RD-150 RD-170 RD-300GX RD-300SX RD-500 RD-600 RD-700/GX/SX RM-2 RMP-3/5 RS-5/9 RS-50/70 RSP-550 RSS-10 RV-70 Procedure Press MENU. Use the ^/v buttons to select “FACTORY RESET.” Press REC twice. Power on while holding CURSOR PAGE and PARAM SELECT, then press ENTER twice Power on while holding ENTER and the RIGHT (>) CURSOR button, then press ENTER twice Power on while holding MIDI and ASSIGN, then press YES twice Power on while holding WRITE Power on while holding REC (WARNING: This will erase the original factory Performance settings. However, you can save them to disk before doing this procedure.) Power on while holding WRITE Power on while holding PLAY MODE and LOOP SYNC. Press ENTER. Power on while holding REC and PLAY Power on while holding WRITE Press EDIT. Use INC/DEC to select “Utility,’ then press ENTER. Use INC/DEC to select “Factory Reset,” then press ENTER twice. Press EDIT. Use INC/DEC to select “UtL,” then press ORGAN. Press ENTER twice. Power on while holding NUMBER 1 and 8. Press DEC/YES Press EDIT. Press the RIGHT PAGE button until “Initialize All” is displayed. Press INC/YES twice. Press EDIT to return to Play mode Press EDIT. CURSOR down to “9 UTILITY” and press ENTER. CURSOR down to “Factory Reset All” and press ENTER three times Power on while holding VALUE UP, SELECT and METRONOME. When “rSt” flashes in the display, press METRONOME again Power on while holding STOP/START. Press and hold STOP/START until reset is completed. With the unit on, press UTILITY. Use VALUE + / - to select “Factory Reset”. Press ENTER. Use VALUE + / - to select “All”. Press ENTER twice Press PATCH so it is lit. Press UTILITY so it is lit. Use PAGE/CURSOR Left or Right to select “Ag5: FACTORY RESET.” Press ENTER twice Power on while holding PROGRAM/PAGE UP (^) and DOWN (v), then press WRITE Power on while holding LOCK and OPTION. (The MCR-8 LED lights.) Press DEMO PROGRAM four times. Press DEVICE ID Power on while holding WRITE and DOWN. Use the UP (^) and DOWN (v) buttons to select AL. Press WRITE. Power off, then back on S Model SB-55 SC-33 SC-50/55/MKII SC-88 SC-155 SC-880 SD-35 SDE-330 SDX-330 SE-50 SE-70 SH-01 Procedure Power on while holding CLEAR Power on while holding REVERB and SPLIT, then press YES Power on while holding both INSTRUMENT buttons, then press ALL While holding SELECT, press both INSTRUMENT buttons. Press ALL Power on while holding both INSTRUMENT buttons, then press ALL Press UTILITY. CURSOR UP and use the VALUE DIAL to select Factory Preset. CURSOR DOWN and use the VALUE DIAL to select ALL. Press ENTER twice Power on while holding CLEAR, then press REC Power on while holding SYSTEM and PROGRAM. Use the DATA dial to select SYSTEM + PROGRAM. Press MEMORY Power on while holding SYSTEM and PROGRAM. Use the DATA dial to select SYSTEM + PROGRAM. Press MEMORY Power on while holding PARAM UP (^) and VALUE UP (^). Press WRITE. Wait three seconds and press WRITE again Power on while holding in the NUMBER/VALUE knob. Press PARAMETER LEFT (<), then dial to STANDARD mode or GUITAR mode. Press WRITE Power on while holding PRESET PATCH and USER PATCH (keep holding until TAP TEMPO ©2010 Roland Corporation U.S. Page 7 ® R SH-32 SH-201 Sonic Cell SP-202 SP-303 SP-404 SP-505 SP-606 SP-808 SPD-S SPD-6 SPD-8 SPD-11/20 SPD-30 SRV-330 SRV-2000 SRV-3030/D SX-700 Factory Reset Procedures goes out). Press WRITE. Power on while holding 1/A. Press the VALUE UP/DOWN buttons to select the desired target to be initialized. Press WRITE/EXEC twice Power on while holding PRESET and USER. Press WRITE. Press MENU, then select UTILITY. Select FACTORY RESET, then select OK and press CURSOR/VALUE. CAUTION: This procedure will erase all of the internal samples and initialize the unit: Hold down CANCEL and press DEL, then press the A/B button. Press DEL Power on while holding CANCEL, REMAIN, DEL. Press REC Power on while holding CANCEL, REMAIN, and DEL. When “ini” shows in the display, press REC Press SONG or PTN to display the Play screen. Press SYSTEM to display the system screen. Press F1 (UTILITY). Press F3 (INIT). Set desired target to be initialized with VALUE dial.(ALL, SYSTEM, SAMPLE, SEQ). Press F1 twice Caution: Initializing the unit permanently deletes all samples out of the internal memory. Press MENU. Press CURSOR to select “SYSTEM” and then press ENTER. Press F3 twice Press SYSTEM/DISK and CURSOR to 4.Init SystemParam?. Press ENTER Press SETUP. Press PAGE Right to select INIT/DELETE. Press ENTER. Use + or – to select “ALL.” Press ENTER Power on while holding DRUMS/U1, PERC/U2, SFX/U3 and OTHERS/U4. Press OTHERS/U4 to execute the reset Power on while holding EDIT, then press COPY. Use the VALUE UP (^) and DOWN (v) to select F A L in the window. Press ALL/ENTER Power on while holding ALL/ENTER and the DOWN ARROW button. Press ALL/ENTER Press MENU. Use Knob 1 to select “SYSTEM” then press Button 3 [ENTER]. Press Button 2 to select the “F.RESET” tab. Use Knob 1 to select “Factory Reset” then press Button 3 [ENTER]. Power on while holding SYSTEM and PROGRAM. Use the DATA dial to select SYSTEM + PROGRAM. Press MEMORY Factory: Power on while holding WRITE and REVERB NON-LINEAR. Delay Mode: Power on while holding WRITE, REVERB NON-LINEAR and ROOM SIMULATE With the unit on, press MEMORY. Use NUMBER/ENTER dial to select FACTORY RESET. Press NUMBER/ENTER twice Press UTILITY. Use PARAMETER LEFT (<) and RIGHT (>) to select FACT INIT. Press WRITE T Model TD-3 TD-4 TD-5 TD-6/V TD-7 TD-7T TD-8 TD-9 TD-10 TD-12 TD-20/20X TMC-6 TR-505 TR-626 TR-707/727 Procedure Power on while holding the + and – buttons. Release them, and then press DRUM KIT Press MENU. Use the ^/v buttons to select “9 OPTIONS” then press OK. Use the ^/v buttons to select “Factory Reset” then press OK. Use the Dial to select “All” then press the SEL [v] button. Press OK. Power on while holding EDIT and START/STOP, then press START/STOP again Power on while holding SHIFT and EDIT SETUP. Press INC/+ to select ALL. Press ENTER twice Press SYSTEM. Use the LEFT (<) and RIGHT (>) CURSOR buttons to select INI, then press ENTER. Cursor to HI HAT and use the DATA dial to select ALL. Press ENTER twice Power on while holding SYSTEM and JUMP, then press ENTER Press SETUP, then F3 MENU. Rotate VALUE to select “RESET.” Press F3 and use VALUE to select ALL. Press F3 EXEC to execute Press SETUP, then press F3 four times. Press SETUP, then press F4 four times Press SETUP, then press F5 three times Press SETUP. Press F5 twice Power on while holding TRIGGER SELECT and EDIT, release both then press EDIT again Power on while holding MODE and PATTERN GROUP KEY A Power on while holding MODE and TRACK #1 Power on while holding TRACK WRITE and TRACK #1 ©2010 Roland Corporation U.S. Page 8 ® R TR-909 Factory Reset Procedures Power on while holding TRACK #1 and PATTERN #1 U Model U-110 Procedure Power on while holding PART and EDIT V Model VA-3 VA-5/7 VA-76 V-BASS VB-99 VF-1 VG-8/8EX VG-88 VG-99 VGA-5/7 VK-7 VK-8 VK-8M VK-77 VK-88 VK-1000 VM-3100/Pro VM/C-7100/7200 V-Piano VP-7 VP-70 VP-770 VP-9000 VR-700 V-Synth V-Synth GT V-SynthXT VS-1880/1824CD VS-2000CD VS-2400CD VS-2480 Procedure Press FUNCTION/MENU. Touch [Global Parameter]. Touch [ALL] Power on while holding MELODY/INTELL, CONTROLLERS and EFFECTS With the unit on, press the FUNCTION/MENU button. Press ”GLOBAL PARAMETER” on the touch screen. Then press ”ALL” on the touch screen Power on while holding PAGE left and PAGE right. Press WRITE Press [SYSTEM]. Press Page [>] to display Page 3. Press F2 [F.RST]. Select ALL , then press F6 [EXEC]. Press WRITE. With the unit on press UTILITY. Use NUMBER/VALUE dial to select “Factory Reset”. Press NUMBER/VALUE three times Power on while holding F1, F3, and F5. Press F6 for All, F4 for Patches, or F2 for System Power on while holding PAGE (>) and PAGE (<). Press WRITE twice Press SYSTEM. Press PAGE (>) to display page 3. Press F1 “F.RST.” Press F6 “EXEC” then press WRITE. Power on while holding WRITE. Release WRITE, then press WRITE again Power on while holding MAIN, SUB and PEDAL in the HARMONIC BAR PART section Power on while holding the UPPER, LOWER, and PEDAL buttons in the HARMONIC BAR PART section. Release and re- press the UPPER, LOWER, and PEDAL buttons once again With the unit on, confirm that the VOLUME is at the MIN position, then power off. Power on while holding BAND, WRITE, and H-BAR MANUAL Press EDIT. Use the RIGHT/LEFT ARROW buttons to select UTILITY and press ENTER. Use the UP/DOWN ARROW buttons to select Factory Reset. Press WRITE, then press ENTER Power one while holding BANK, WRITE, and H-BAR MANUAL. Continue holding BANK, WRITE, and H-BAR MANUAL until all panel indicators light. Press WRITE, then press F3 to access the INIT MENU screen. Press F4 to access the COLD BOOT screen, then press ENTER Press SYSTEM, then press F1-F4 ON/OFF. Use the VALUE dial to put a check in the ALL box and press ENTER three times Power on while holding PROJECT/SYS and F1. Continue to press F1 until completed Press FUNCTION so it is lit. Press F4 [UTILITY]. Use the VALUE dial to select “9. Initialize” then press ENTER. Use the VALUE dial to select “2. Factory Reset All” then press ENTER. Press F4 [Execute] then press F4 [OK]. Power on while holding BYPASS and FEMALE CHOIR. Power on while holding PLAY, VOICE EXPANSION, and MIDI Press MENU. Cursor to “Factory Reset” then press F2 [ENTER]. Press F1 [OK]. With the unit on, press UTILITY until it is lit. If the UTILITY Menu1 screen is displayed, press PART/ >. (the UTILITY Menu2 screen will appear). Press F1 (FACTORY). Press F6(EXEC) Press FUNCTION/ENTER. Use the +/- buttons to display “Utl.” Press STRINGS, then press FUNCTION/ENTER twice. With the unit on, Press MODE. Touch FACORY RESET, then touch EXECUTE Press UTILITY. Touch “FACTORY RESET,” then touch “EXECUTE.” Press MODE. Touch “SYSTEM.” Touch “INIT.” Touch “EXECUTE.” Hold shift and press F5/. Page to “INIT”. Press F1. Press ENTER/YES Hold SHIFT and press F4 (Utility). Press PAGE to get to page 3. Press F1 (PrmIni). Press F5. Press ENTER/YES Hold SHIFT and press F4 (Utility). Press PAGE to get to page 3. Press F6 (PrmIni). Press F5. Press ENTER/YES Press UTILITY. Press PAGE to get to page 3. Press F6 (PrmIni). Press F5. Press ©2010 Roland Corporation U.S. Page 9 ® R VT-1 W Model W-50 X Model XP-10 XP-30 XP-50 XP-60/80 XV-88 XV-2020 XV-3080 XV-5050 XV-5080 Factory Reset Procedures ENTER/YES Power on while holding down the PRESET/USER button Procedure Press CONTROL and MASTER simultaneously. Use PARAMETER UP (^) and DOWN (v) to select ALL. Press VALUE UP (^) Procedure Press UTILITY. Use VALUE + and - to select INITIALIZE, then press ENTER. Use VALUE + and - to select FACTORY PRESET, then press ENTER Press UTIL/CARD and use the CURSOR buttons to select 4:FACTORY RESET. Press ENTER three times. If Write Protect is on, press DEC once, then press ENTER three times Press DISK/UTILITY, select SOUND, select PRESET, then press ENTER. Use the dial to turn Memory Protect OFF if necessary, then press ENTER twice Press UTILITY, press F6 (MENU) twice to select Factory, then ENTER. Press F6 (EXECUTE). Use the dial to turn Memory Protect OFF if necessary, press ENTER, then press F6 (EXECUTE) With the unit on, press UTILITY. Cursor down to Utility Menu 2. Cursor right 3 times to select “FACTORY RESET”. Press ENTER twice. If Internal Write Protect is set to ON, turn the VALUE dial to select OFF, then press ENTER 3 times While holding down VOLUME, press VALUE. Release them, then turn CATEGORY/BANK to select “PIANO.” Rotate VALUE until “Fct” shows in the display. Press VALUE Twice With unit on, press UTILITY. Press UP or DOWN cursor buttons to select the UTIL 2 page. Use LEFT or RIGHT cursor buttons to select “FACTORY RESET”. Press ENTER twice With the unit on, press UTILITY. Press CURSOR left until “FACTORY RESET” shows in the display. Press ENTER twice. If “WRITE PROTECT ON” is displayed, turn the VALUE dial to select “OFF”, then press ENTER twice With the unit on, press SYSTEM/UTILITY. Press F6 [MENU] to select menu 3. Press F1[FACTORY], then press F6 [FACTORY]. If “INT WRITE PROTECT=ON” is displayed, press DEC, then press F6 twice ©2010 Roland Corporation U.S. Page 10
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Author : Comments : Company : Roland Corporation U.S. Create Date : 2010:09:14 09:19:31-07:00 Modify Date : 2010:09:14 09:19:37-07:00 Source Modified : D:20100914161905 Subject : Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Creator Tool : Acrobat PDFMaker 9.1 for Word Metadata Date : 2010:09:14 09:19:37-07:00 Producer : Acrobat Distiller 9.3.3 (Windows) Keywords : Format : application/pdf Creator : Title : Roland Description : Document ID : uuid:7d3a96cc-61d0-413d-be23-7bf022a2e17d Instance ID : uuid:056857a7-66e8-4895-9a5b-8d0e360221c1 Page Layout : OneColumn Page Count : 10EXIF Metadata provided by EXIF.tools