GEI 100363 Fuji AF300 G11 Manual

• AF-300 G11User's Guide
  • Table of Contents
    • AF-300 G11 ™ Model Numbering System Diagram
    • AF-300 G11 Dimensions & Weights
  • 1. Before Using This Product
    • 1.1 Receiving Instructions
    • 1.2 Appearance
    • 1.3 Handling the Product
    • 1.4 Carrying
    • 1.5 Storage
    • 1.6 AF-300 G11 Drive Ratings Efficiency and Watts Loss
  • 2. Installation Environment and Connection
    • 2.1 Operating Environment
    • 2.2 Installation Method
    • 2.3 Connection
      • 2.3.1 Basic Connection
      • 2.3.2 Connecting the Main Circuit and Ground Terminals
      • 2.3.3 Connecting the Control Terminals
      • 2.3.4 Terminal Configuration
      • 2.3.5 AF-300 G11 Drive Cable Size, Tightening Torque and Circuit Protection Rating
      • 2.3.6 DC Link Reactor
  • 3. Operation
    • 3.1 Inspection and Preparation Before Operation
    • 3.2 Operation Method
    • 3.3 Trial Run STOP
  • 4. Keypad Panel
    • 4.1 Appearance of Keypad Panel
    • 4.2 Operation From the Keypad Panel (LCD Screen, Level Structure)
      • 4.2.1 Normal Operation
      • 4.2.2 Alarm Modes
    • 4.3 Entering Data on the Keypad Panel
      • 4.3.1 Operation Mode
      • 4.3.2 Setting Digital Frequency
      • 4.3.3 Switching to LED Digital Monitor
      • 4.3.4 Program Menu Screen
      • 4.3.5 Setting Function Data
      • 4.3.6 Checking Function Data
      • 4.3.7 Monitoring Operating Status
      • 4.3.8 I/O Check
      • 4.3.9 Maintenance Information
      • 4.3.10 Load Rate Measurement
      • 4.3.11 Alarm Information
      • 4.3.12 Alarm History and Factors
      • 4.3.13 Data Copy
      • 4.3.14 Alarm Mode
  • 5. Function Selection
    • 5.1 Function Select List
    • 5.2 Alphabetical Function List
    • 5.3 Function Explanation
  • 6. Protective Operations
    • 6.1 List of Protective Functions
    • 6.2 Alarm Reset
  • 7. Troubleshooting
    • 7.1 Activation of Protective Function
    • 7.2 Abnormal Motor Rotation
  • 8. Maintenance and Inspection
    • 8.1 Daily Inspections
    • 8.2 Periodic Inspections
    • 8.3 Main Circuit Measurements
    • 8.4 Insulation Test
    • 8.5 Replacement Parts
  • 9. Warranty Parts and Service
  • 10. Replacement Parts
  • 11. Specifications
    • 11.1 Standard Specifications
    • 11.2 Common Specifications
    • 11.3 Outline Dimensions
      • 11.3.1 Outline Dimensions NEMA 1
      • 11.3.2 Outline Dimensions Open Type
      • 11.3.3 Outline Dimensions Open Type with NEMA 12 Heatsink
  • 12. RS485 Modbus RTU Serial Communications
    • 12.1 Transmission Specification
    • 12.2 Connection
    • 12.3 Serial Interface Configuration
    • 12.4 Modbus RTU Functions
    • 12.5 Drive Function Code Access
    • 12.6 Command and Monitor Data Registers
    • 12.7 Data Format Specification
    • 12.8 Communication Errors
  • 13. Options
    • 13.1 Built-in Options
  • 14. Electromagnetic Compatibility (EMC)
    • 14.1 General
    • 14.2 Recommended Installation Instructions