FINEPIX S4000/S4000A/S3900 Series, S3400/S3300/S3200 Series Owner's Manual Fujifilm Fine Pix S3900 User Guide And Product Specification

User Manual: Fujifilm-FinePix-S3900-Manual-user-Guide-and-Product-Specification

Open the PDF directly: View PDF .
Page Count: 147

Download
Open PDF In Browser	View PDF

BL01268-200

DIGITAL CAMERA

FINEPIX

S4000/S4000A/S3900 Series
S3400/S3300/S3200 Series
Owner’s Manual
Thank you for your purchase of this product. This manual describes how to use your
FUJIFILM FinePix S4000/S4000A/S3900 series, S3400/S3300/S3200 series digital camera and the supplied software. Be sure that
you have read and understood its contents
before using the camera.

Before You Begin
First Steps
Basic Photography and Playback
More on Photography
More on Playback
Movies
Connections
Menus
Technical Notes

For information on related products, visit our website at
http://www.fujifilm.com/products/digital_cameras/index.html

Troubleshooting
Appendix

For Your Safety

IMPORTANT SAFETY INSTRUCTIONS
• Read Instructions: All the safety and
operating instructions should be
read before the appliance is operated.
• Retain Instructions: The safety and
operating instructions should be
retained for future reference.
• Heed Warnings: All warnings on the
appliance and in the operating instructions should be adhered to.
• Follow Instructions: All operating
and use instructions should be followed.

Installation
Power Sources: This video product
should be operated only from the
type of power source indicated on
the marking label. If you are not sure
of the type of power supply to your
home, consult your appliance dealer
or local power company. For video
products intended to operate from
battery power, or other sources, refer
to the operating instructions.
Grounding or Polarization: This video
product is equipped with a polarized alternating-current line plug (a
plug having one blade wider than
the other). This plug will fit into the
power outlet only one way. This is a
safety feature. If you are unable to insert the plug fully into the outlet, try
reversing the plug. If the plug should
still fail to fit, contact your electrician
to replace your obsolete outlet. Do

not defeat the safety purpose of the This video product should never be
placed near or over a radiator or heat
polarized plug.
register.
Alternate Warnings: This video
product is equipped with a 3-wire Attachments: Do not use attachments
grounding-type plug, a plug having not recommended by the video
a third (grounding) pin. This plug will product manufacturer as they may
only fit into a grounding-type power cause hazards.
outlet. This is a safety feature. If you
Water and Moisture: Do not use this
are unable to insert the plug into
video product near water – for exthe outlet, contact your electrician
ample, near a bath tub, wash bowl,
to replace your obsolete outlet. Do
kitchen sink, or laundry tub, in a wet
not defeat the safety purpose of the
basement, or near a swimming pool,
grounding-type plug.
and the like.
Overloading: Do not overload wall
Power-Cord Protection: Power-Supoutlets and extension cords as this
ply cords should be routed so that
can result in a risk of fire or electric
they are not likely to be walked on
shock.
or pinched by items placed upon
Ventilation: Slots and openings in the or against them, paying particular
cabinet are provided for ventilation attention to cords at plugs, conveand to ensure reliable operation of nience receptacles, and the point
the video product and to protect it where they exit from the appliance.
from overheating, and these openAccessories: Do not place this video
ings must not be blocked or covproduct on an unstable cart, stand,
ered.
tripod, bracket, or table. The video
The openings should never be
product may fall, causing serious inblocked by placing the video prodjury to a child or adult, and serious
uct on a bed, sofa, rug, or other simidamage to the appliance. Use only
lar surface.
with a cart, stand, tripod, bracket, or
This video product should not be
table recommended by the manuplaced in a built-in installation such
facturer, or sold with the video prodas a bookcase or rack unless proper
uct. Any mounting of the appliance
ventilation is provided or the manshould follow the manufacturer’s inufacturer’s instructions have been
structions, and should use a mountadhered to.
ing accessory recommended by the
manufacturer.

An
appliance
and cart combination should
be moved with
care. Quick stops,
excessive force,
and uneven surfaces may cause the appliance and
cart combination to overturn.

Antennas
Outdoor Antenna Grounding: If an
outside antenna or cable system is
connected to the video product, be
sure the antenna or cable system
is grounded so as to provide some
protection against voltage surges
and built-up static charges. Section
810 of the National Electrical Code,
ANSI/NFPA No. 70, provides information with respect to proper grounding
of the mast and supporting structure, grounding of the lead-in wire
to an antenna-discharge unit, size of
grounding conductors, location of
antenna-discharge unit, connection
to grounding electrodes, and requirements for the grounding electrode.

For Your Safety
Power Lines: An outside antenna system should not be located in the
vicinity of overhead power lines or
other electric light or power circuits,
or where it can fall into such power
lines or circuits. When installing an
outside antenna system, extreme
care should be taken to keep from
touching such power lines or circuits
as contact with them might be fatal.
EXAMPLE OF ANTENNA GROUNDING
AS PER NATIONAL ELECTRICAL CODE
Ground Clamp
Electric
Service
Equipment
Ground
Clamps
Power Service
Grounding Electrode
System (NEC ART 250.
PART H)

Antenna
Lead in Wire

Antenna
Discharge Unit
(NEC SECTION
810-20)
Grounding
Conductors
(NEC SECTION
810-21)

Use
Cleaning: Unplug this video product
from the wall outlet before cleaning. Do not use liquid cleaners or
aerosol cleaners. Use a damp cloth
for cleaning.
Object and Liquid Entry: Never push
objects of any kind into this video
product through openings as they
may touch dangerous voltage
points or short out parts that could
result in a fire or electric shock. Never
spill liquid of any kind on the video
product.
Lightning: For added protection for
this video product receiver during
a lightning storm, or when it is left
unattended and unused for long periods of time, unplug it from the wall
outlet and disconnect the antenna
or cable system. This will prevent
damage to the video product due to
lightning and power-line surges.

Replacement Parts: When replacement parts are required, be sure
the service technician has used
replacement parts specified by the
manufacturer or have the same
characteristics as the original part.
Unauthorized substitutions may
result in fire, electric shock or other
Damage Requiring Service: Unplug this hazards.
video product from the wall outlet
and refer servicing to qualified ser- Safety Check: Upon completion of any
vice personnel under the following service or repairs to this video product, ask the service technician to
conditions:
When the power-supply cord or perform safety checks to determine
that the video product is in proper
plug is damaged.
If liquid has been spilled, or objects operating condition.
have fallen into the video product.
If the video product has been exposed to rain or water.
If the video product has been
dropped or the cabinet has been
damaged.
If the video product does not operate normally be following the
operating instructions. Adjust only
those controls that are covered by
the operating instructions as an improper adjustment of other controls
may result in damage and will often
require extensive work by a qualified
technician to restore the video product to its normal operation.
When the video product exhibits a
distinct change in performance - this
indicates a need for service.

Service

Servicing: Do not attempt to service
this video product yourself as opening or removing covers may expose
you to dangerous voltage or other
hazards. Refer all servicing to qualified service personnel.

iii

For Your Safety

Be sure to read this notes before using

WARNING
Do not allow water or foreign objects to enter the camera.
If water or foreign objects get inside the camera, turn the camera
off, remove the battery and disconnect and unplug the AC power
adapter.
Continued use of the camera can cause a fire or electric shock.
• Contact your FUJIFILM dealer.

Safety Notes
• Make sure that you use your camera correctly. Read these Safety Notes and
your Owner’s Manual carefully before use.
• After reading these Safety Notes, store them in a safe place.

About the Icons
The icons shown below are used in this document to indicate the severity of
the injury or damage that can result if the information indicated by the icon
is ignored and the product is used incorrectly as a result.

WARNING

CAUTION

This icon indicates that death or serious injury can result if the information is ignored.
This icon indicates that personal injury or material damage can result
if the information is ignored.

The icons shown below are used to indicate the nature of the information
which is to be observed.
Triangular icons tell you that this information requires attention (“important”).
Circular icons with a diagonal bar tell you that the action indicated is
prohibited (“Prohibited”).
Filled circles with an exclamation mark tell you an action that must be
performed (“Required”).

WARNING
If a problem arises, turn the camera off, remove the battery, disconnect and
unplug the AC power adapter.
Continued use of the camera when it is emitting smoke, is emitting
Unplug
any unusual odor, or is in any other abnormal state can cause a fire
from power
or electric shock.
socket.
• Contact your FUJIFILM dealer.

Do not use in
the bathroom
or shower.

Do not disassemble

Do not use the camera in the bathroom or shower.
This can cause a fire or electric shock.

Never attempt to disassemble or modify (never open the case).
Failure to observe this precaution can cause fire or electric shock.

Should the case break open as the result of a fall or other accident, do not
touch the exposed parts.
Failure to observe this precaution could result in electric shock or in
Do not touch injury from touching the damaged parts. Remove the battery iminternal
mediately, taking care to avoid injury or electric shock, and take the
parts
product to the point of purchase for consultation.
Do not change, heat or unduly twist or pull the connection cord and do not
place heavy objects on the connection cord.
These actions could damage the cord and cause a fire or electric
shock.
• If the cord is damaged, contact your FUJIFILM dealer.
Do not place the camera on an unstable surface.
This can cause the camera to fall or tip over and cause injury.
Never attempt to take pictures while in motion.
Do not use the camera while you are walking or driving a vehicle. This
can result in you falling down or being involved in a traffic accident.
Do not touch any metal parts of the camera during a thunderstorm.
This can cause an electric shock due to induced current from the
lightning discharge.
Do not use the battery except as specified.
Load the battery as aligned with the indicator.

For Your Safety
WARNING
Do not heat, change or take apart the battery. Do not drop or subject the battery to impacts. Do not store the battery with metallic products. Do not use
chargers other than the specified model to charge the battery.
Any of these actions can cause the battery to burst or leak and cause
fire or injury as a result.
Use only the battery or AC power adapters specified for use with this camera.
Do not use voltages other than the power supply voltage shown.
The use of other power sources can cause a fire.
If the battery leaks and fluid gets in contact with your eyes, skin or clothing.
Flush the affected area with clean water and seek medical attention or call an
emergency number right away.
Do not use the charger to charge batteries other than those specified here.
The Ni-MH battery charger is designed for FUJIFILM HR-AA Ni-MH
batteries. Using the charger to charge conventional batteries or other
types of rechargeable batteries can cause the battery to leak fluid,
overheat or burst.
When carrying the battery, install it in a digital camera or keep it in the hard
case. When storing the battery, keep it in the hard case. When discarding,
cover the battery terminals with insulation tape.
Contact with other metallic objects or battery could cause the battery to ignite or burst.
Keep Memory Cards out of the reach of small children.
Because Memory Cards are small, they can be swallowed by children.
Be sure to store Memory Cards out of the reach of small children. If
a child swallows a Memory Card, seek medical attention or call an
emergency number.

CAUTION

CAUTION
Do not place heavy objects on the camera.
This can cause the heavy object to tip over or fall and cause injury.
Do not move the camera while the AC power adapter is still connected. Do not
pull on the connection cord to disconnect the AC power adapter.
This can damage the power cord or cables and cause a fire or electric
shock.
Do not use the AC power adapter when the plug is damaged or the plug socket
connection is loose.
This could cause a fire or electric shock.
Do not cover or wrap the camera or the AC power adapter in a cloth or blanket.
This can cause heat to build up and distort the casing or cause a fire.
When you are cleaning the camera or you do not plan to use the camera for
an extended period, remove the battery and disconnect and unplug the AC
power adapter.
Failure to do so can cause a fire or electric shock.
When charging ends, unplug the charger from the power socket.
Leaving the charger plugged into the power socket can cause a fire.
Using a flash too close to a person’s eyes may temporarily affect the eyesight.
Take particular care when photographing infants and young children.
When a memory card is removed, the card could come out of the slot too quickly. Use your finger to hold it and gently release the card.
Request regular internal testing and cleaning for your camera.
Build-up of dust in your camera can cause a fire or electric shock.
• Contact your FUJIFILM dealer to request internal cleaning every 2
years.
• Please note this is not a free of charge service.

Do not use this camera in locations affected by oil fumes, steam, humidity or
dust.
This can cause a fire or electric shock.
Do not leave this camera in places subject to extremely high temperatures.
Do not leave the camera in locations such as a sealed vehicle or in
direct sunlight. This can cause a fire.
Keep out of the reach of small children.
This product could cause injury in the hands of a child.

For Your Safety
Power Supply and Battery
* Confirm your battery type before reading the following descriptions.

The following explains proper use of
batteries and how to prolong their
life. Incorrect use of batteries can
cause shorter battery life, as well as
leakage, excessive heat, fire or explosion.
1 Camera uses the Rechargeable
Lithium-ion Battery
* When shipped, the battery is not
fully charged. Always charge the
battery before using it.
* When carrying the battery, install it
in a digital camera or keep it in the
soft case.
■ Battery Features
• The battery gradually loses its
charge even when not used. Use
a battery that has been charged
recently (in the last day or two) to
take pictures.
• To maximize the life of the battery,
turn the camera off as quickly as
possible when it is not being used.
• The number of available frames will
be lower in cold locations or at low
temperatures. Take along a spare
fully charged battery. You can also
increase the amount of power produced by putting the battery in
your pocket or another warm place
to heat it and then loading it into
the camera just before you take a
picture.

■ Battery Life
At normal temperatures, the battery can be used at least 300 times.
If the time for which the battery
provides power shortens markedly,
this indicates that the battery has
■ Charging the Battery
• You can charge the battery using reached the end of its effective life
and should be replaced.
the battery charger (included).
- The battery can be charged ■ Notes on storage
at ambient temperatures be- • If a battery is stored for long periods
tween 0°C and +40°C (+32°F
while charged, the performance of
and +104°F). Refer to the Owner’s
the battery can be impaired. If the
Manual for the time of charging
battery will not be used for some
battery.
time, run the battery out before
- You should charge the battery
storing it.
at an ambient temperature be- • If you do not intend to use the
tween +10°C and +35°C (+50°F
camera for a long period of time,
and +95°F). If you charge the
remove the battery from the cambattery at a temperature outside
era.
this range, charging takes longer • Store the battery in a cool place.
because the performance of the
- The battery should be stored in
battery is impaired.
a dry location with an ambient
- You cannot charge the battery
temperature between +15°C and
at temperatures of 0°C (+32°F) or
+25°C (+59°F and +77°F).
below.
- Do not leave the battery in hot or
• The Rechargeable Lithium-ion Batextremely cold places.
tery does not need to be fully dis■ Handling the Battery
charged or exhausted flat before
Cautions for Your Safety:
being charged.
• Do not carry or store battery with
• The battery may feel warm after it
metal objects such as necklaces or
has been charged or immediately
hairpins.
after being used. This is perfectly • Do not heat the battery or throw it
normal.
into a fire.
• Do not recharge a fully charged • Do not attempt to take apart or
battery.
change the battery.
If you are using a heating pad, take
care not to place the battery directly against the pad. The camera
may not operate if you use a depleted battery in cold conditions.

• Dispose of used battery promptly.
• Do not drop the battery or otherwise subject it to strong impacts.
• Do not expose the battery to water.
• Always keep the battery terminals
clean.
• Do not store batteries in hot places. Also, if you use the battery for
a long period, the camera body
and the battery itself will become
warm. This is normal. Use the AC
power adapter if you are taking
pictures or viewing images for a
long period of time.
2 Camera uses AA-size alkaline or Ni-MH
(nickel-metal hydride) rechargeable
batteries
* For details on the batteries that
you can use, refer to the Owner’s
Manual of your camera.

■ Cautions for Using Battery
• Do not heat the batteries or throw
them into a fire.
• Do not carry or store batteries with
metal objects such as necklaces or
hairpins.
• Do not expose the batteries to water, and keep batteries from getting
wet or stored in moist locations.
• Do not attempt to take apart or
change the batteries, including
battery casings.
• Do not subject the batteries to
strong impacts.
• Do not recharge the battery with
• Do not use batteries that are leakchargers other those specified.
ing, deformed, discolored.

For Your Safety
• Do not store batteries in warm or
If any liquid at all leaks from
humid places.
the batteries, wipe the battery
• Keep the batteries out of reach of
compartment thoroughly and
babies and small children.
then load new batteries.
• Make sure that the battery polarity
If any battery fluid comes into
(C and D) is correct.
contact with your hands or
• Do not use new with used batterclothing, flush the area thories. Do not use charged and disoughly with water. Note that
charged batteries together.
battery fluid can cause loss
• Do not use different types or
of eyesight if it gets into your
brands of batteries at the same
eyes. If this occurs, do not rub
time.
your eyes. Flush the fluid out
• If you do not intend to use the
with clean water and contact
camera for a long period of time,
your physician for treatment.
remove the batteries from the
camera. Note if the camera is left ■ Using the AA-size Ni-MH batteries
with the batteries removed, the
correctly
time and date settings are cleared. • Ni-MH batteries left unused in
• The batteries feel warm right afstorage for long periods can beter being used. Before removing
come “deactivated”. Also, repeatthe batteries, turn the camera off
edly charging Ni-MH batteries
and wait for the batteries to cool
that are only partially discharged
down.
can cause them to suffer from the
• Since batteries do not work well in
“memory effect”. Ni-MH batteries
cold weather or locations, warm
that are “deactivated” or affected
the batteries by placing them inby “memory” suffer from the probside your garments before use.
lem of only providing power for a
Batteries do not work well when
short time after being charged. To
cold. They will work again when
prevent this problem, discharge
the temperature returns to normal.
and recharge them several times
• Soil (such as fingerprints) on the
using the camera’s “Discharging
battery terminals makes the batrechargeable batteries” function.
teries charge less reducing the
Deactivation and memory are spenumber of images. Carefully wipe
cific to Ni-MH batteries and are not
the battery terminals with a soft
in fact battery faults.
dry cloth before loading.
See Owner’s Manual for the procedure for “Discharging rechargeable
batteries”.

CAUTION
Do not use the “Discharging rechargeable batteries” function when
alkaline batteries being used.
• To charge Ni-MH batteries, use the
quick battery charger (sold separately). Refer to the instructions
supplied with the charger to make
sure that the charger is used correctly.
• Do not use the battery charger to
charge other batteries.
• Note that the batteries feel warm
after being charged.
• Due to the way the camera is constructed, a small amount of current
is used even when the camera is
turned off. Note in particular that
leaving Ni-MH batteries in the
camera for a long period will overdischarge the batteries and may
render them unusable even after
recharging.
• Ni-MH batteries will self-discharge
even when not used, and the time
for which they can be used may be
shortened as a result.
• Ni-MH batteries will deteriorate
rapidly if over-discharged (e.g.
by discharging the batteries in a
flashlight). Use the “Discharging rechargeable batteries” function provided in the camera to discharge
the batteries.

• Ni-MH batteries have a limited
service life. If a battery can only
be used for a short time even after
repeated discharge-charge cycles,
it may have reached the end of its
service life.
■ Disposing of Batteries
• When disposing of batteries, do
so in accordance with your local
waste disposal regulations.
3 Notes on both models ( 1 , 2 )
■ AC Power Adapter
Always use the AC Power Adapter
with the camera. The use of an AC
Power adapter other than FUJIFILM
AC Power Adapter can be damaged
to your digital camera.
For details on the AC power adapter,
refer to the Owner’s Manual of your
camera.
• Use the AC power adapter for indoor use only.
• Plug the connection cord plug securely into the DC input terminal.
• Turn off the FUJIFILM Digital camera before disconnecting the cord
from the DC input terminal. To disconnect, pull out the plug gently.
Do not pull on the cord.
• Do not use the AC power adapter
with any device other than your
camera.
• During use, the AC power adapter
will become hot to the touch. This
is normal.

vii

For Your Safety
• Do not take apart the AC power
adapter. Doing so could be dangerous.
• Do not use the AC power adapter
in a hot and humid place.
• Do not subject the AC power
adapter to strong shocks.
• The AC power adapter may emit a
humming. This is normal.
• If used near a radio, the AC power
adapter may cause static. If this
happens, move the camera away
from the radio.

unless intended only for personal
use. Note that some restrictions apply to the photographing of stage
performances, entertainments and
exhibits, even when intended purely
for personal use. Users are also asked
to note that the transfer of Memory
Card containing images or data protected under copyright laws is only
permissible within the restrictions
imposed by those copyright laws.

■ Handling Your Digital Camera
To ensure that images are recorded
correctly, do not subject the camera
Before Using the Camera
to impact or shock while an image is
Do not aim the camera at extremely
being recorded.
bright light sources, such as the sun
in a cloudless sky. Failure to observe ■ Liquid Crystal
this precaution could damage the If the LCD monitor is damaged, take
particular care with the liquid crystal
camera image sensor.
in the monitor. If any of the follow■ Test Shots Prior to Photography
ing situations arise, take the urgent
For important photographs (such as
action indicated.
weddings and overseas trips), always
• If liquid crystal comes in contact
take a test shot and view the imwith your skin:
age to make sure that the camera is
Wipe the area with a cloth and
working normally.
then wash thoroughly with soap
• FUJIFILM Corporation cannot acand running water.
cept liability for any incidental
• If liquid crystal gets into your eye:
losses (such as the costs of photogFlush the affected eye with clean
raphy or the loss of income from
water for at least 15 minutes and
photography) incurred as a result
then seek medical assistance.
of faults with this product.
• If liquid crystal is swallowed:
■ Notes on Copyright
Flush your mouth thoroughly with
Images recorded using your digital
water. Drink large quantities of wacamera system cannot be used in
ter and induce vomiting. Then seek
ways that infringe copyright laws
medical assistance.
without the consent of the owner,

viii

Although the LCD panel is produced
with highly sophisticated technologies, there may be black spots or
permanently lit spots. This is not a
malfunction, and does not affect recorded images.
■ Trademark Information
• E and xD-Picture Card™ are
trademarks of FUJIFILM Corporation.
• IBM PC/AT is a registered trademark
of International Business Machines
Corp. of the U.S.A.
• Macintosh, QuickTime, and Mac OS
are trademarks of Apple Inc. in the
U.S.A. and other countries.
• Windows 7, Windows Vista and the
Windows logo are trademarks of
the Microsoft group of companies.
• IrSimple™ Trademark is owned by
the Infrared Data Association®.
• IrSS™ Trademark or IrSimpleShot™
Trademark is owned by the Infrared Data Association®.
• SDHC logo is a trademark of SD-3D,
LLC.
• HDMI logo is a trademark.
• YouTube is a trademark of Google
Inc.
• Other company or product names
are trademarks or registered trademarks of the respective companies.

■ Notes on Electrical Interference
If the camera is to be used in hospitals or aircrafts, please note that
this camera may cause interference
to other equipment in the hospital
or aircraft. For details, please check
with the applicable regulations.
■ Explanation of Color Television
System
NTSC: National Television System
Committee, color television
telecasting
specifications
adopted mainly in the U.S.A.,
Canada and Japan.
PAL:

Phase Alternation by Line, a
color television system adopted mainly by European
countries and China.

■ Exif Print (Exif ver. 2.3)
Exif Print Format is a newly revised
digital camera file format that contains a variety of shooting information for optimal printing.

IMPORTANT NOTICE: Read Before
Using the Software
Direct or indirect export, in whole or
in part, of licensed software without
the permission of the applicable
governing bodies is prohibited.

About This Manual
Before using the camera, read this manual and the warnings on pages ii–viii. For information on specific topics, consult the sources below.
✔ Camera Q & A ......................................................pg.
...................................................... pg. x
Know what you want to do but don’t know the
name for it? Find the answer in “Camera Q & A.”

✔ Table of Contents .............................................
.............................................pg.
pg. xiii
The “Table of Contents” gives an overview of the
entire manual. The principal camera operations
are listed here.

✔ Troubleshooting .............................................
.............................................pg.
pg. 109
Having a specific problem with the camera? Find
the answer here.

✔ Warning Messages and Displays ...................... pg. 116
Find out what’s behind that flashing icon or error
message in the display.

✔ Glossary .........................................................pg.
......................................................... pg. 120
The meanings of some technical terms may be
found here.

Memory Cards
Pictures can be stored on optional SD or SDHC memory cards. In this manual, SD memory cards are referred to
as “memory cards.” For more information, see page 10.

Camera Q & A
Find items by task.
Camera Setup
Question
How do I set the camera clock?
Can I set the clock to local time when I travel?
How do I keep the display from turning off automatically?
How do I make the display brighter or darker?
How do I stop the camera beeping and clicking?
Can I change the sound the shutter makes?
What do the icons in the display mean?
How much charge is left in the battery?
Can I increase the capacity of rechargeable Ni-MH batteries?

Key phrase
See page
Date and time
14
Time difference
101
Auto power off
104
LCD brightness
104
Operation and shutter volume
99
Silent mode
18
Shutter sound
99
Displays
4
Battery level
16
Discharge
105

Sharing Pictures
Question
Can I print pictures on my home printer?

Key phrase
Printing pictures

See page
62

Camera Q & A

Taking Pictures
Question
How can I avoid blurred pictures?
How can I make good portraits?
Can the camera automatically adjust settings for different scenes?
Can I choose my own settings for different scenes?
How can I be sure my subject is smiling when I take a photograph?
How can I be sure that nobody blinked when the photo was taken?
Can I prioritize to focus the specified person’s face?
How do I shoot close-ups?
How do I keep the flash from firing?
How do I stop my subjects’ eyes glowing red when I use the flash?
How do I “fill-in” shadows on back-lit subjects?
How do I take a series of pictures in a single burst?
How do I take a group portrait that includes the photographer?
How do I shoot a panorama?
Can I choose shutter speed and aperture?
Can I save and recall camera settings?
How do I adjust exposure?
How do I keep a moving subject in focus?
How do I shoot movies?
How do I frame pictures in the viewfinder?

Key phrase
Dual IS mode
Intelligent Face Detection
M mode
Scene position
Smile detection
Blink detection
Face Recognition
Macro mode (close-ups)

See page
17
31
15
21
22
32
82
35

Flash mode

Continuous Shooting mode
Self-timer mode
Motion panorama
P, S, A, and M modes
C mode
Exposure compensation
Tracking
Recording movies
EVF/LCD button

40
38
24
26
30
44
82
57
5

Camera Q & A

Viewing Pictures
Question
How do I view my pictures?
How can I delete pictures easily?
How can I select and delete individual pictures or delete all pictures
at once?
Can I zoom in on pictures during playback?
Can I mark images with favorite (I) rating?
How do I view a lot of pictures at once?
Can I create photobooks from my favorite pictures?
How do I find pictures?
Can I protect my pictures from accidental deletion?
Can I hide the icons in the display when viewing my pictures?
Can I select pictures for upload to YouTubeTM?
Can I select pictures for upload to Facebook?

xii

Key phrase
Single-frame playback
The b button

See page
46
20

Deleting pictures

Playback zoom
I Favorites
Multi-frame playback
Photobook assist
Image search
Protect
Choosing a display format

47
47
49
51
53
92
46

Uploading pictures

Table of Contents
For Your Safety ................................................................................. ii
IMPORTANT SAFETY INSTRUCTIONS ...................................... ii
Safety Notes .................................................................................... iv
About This Manual ......................................................................... ix
Camera Q & A ..................................................................................... x

Before You Begi
Begin
n
Introduction....................................................................................... 1
Symbols and Conventions .......................................................... 1
Supplied Accessories .................................................................... 1
Parts of the Camera ....................................................................... 2
Camera Displays .......................................................................... 4
The Mode Dial .............................................................................. 6

First Steps
Steps
The Strap and Lens Cap ................................................................ 7
Inserting the Batteries .................................................................. 8
Inserting a Memory Card ...........................................................10
Turning the Camera on and Off ..............................................13
Shooting Mode .............................................................................13
Playback Mode ..............................................................................13
Basic Setup .......................................................................................14

Basic Photography and Playbac
Playback
k
Taking Pictures in M (Scene Recognition) Mode...15
Viewing Pictures ............................................................................20

More on Photography
Photography
Shooting Mode ...............................................................................21
M SCENE RECOGNITION .................................................21
B AUTO ..........................................................................................21
SP SCENE POSITION ....................................................................21
N MOTION PANORAMA .....................................................24
P: PROGRAM AE ............................................................................26
S: SHUTTER PRIORITY AE ...........................................................27
A: APERTURE PRIORITY AE ........................................................28
M: MANUAL ....................................................................................29
C: CUSTOM MODE ........................................................................30
Intelligent Face Detection .........................................................31
Blink Detection .............................................................................32
Focus Lock ........................................................................................33
F Macro and Super Macro Modes (Close-ups) ...............35
N Using the Flash (Intelligent Flash) .....................................36
J Using the Self-Timer...............................................................38
I Continuous Shooting (Burst Mode)................................40
c Instant Zoom ............................................................................42
d Exposure Compensation.....................................................44

xiii

Table of Contents
More on Playbac
Playback
k

Menuss
Menu

Playback Options...........................................................................46
Playback Zoom..............................................................................47
I Favorites: Rating Pictures ....................................................47
Viewing Photo Information......................................................48
Multi-Frame Playback.................................................................49
Viewing Panoramas......................................................................50
k PhotoBook Assist....................................................................51
Creating a PhotoBook ................................................................51
Viewing PhotoBooks ..................................................................52
Editing and Deleting PhotoBooks .........................................52
b Image Search ............................................................................53
A Deleting Pictures ....................................................................54
Deleting One Picture ..................................................................54
Deleting Multiple Pictures .......................................................55
Deleting All Pictures ...................................................................56

Using the Menus: Shooting Mode .........................................74
Using the F-Mode Menu..........................................................74
F-Mode Menu Options .............................................................75
N ISO ............................................................................................75
O IMAGE SIZE ............................................................................76
P FINEPIX COLOR ....................................................................77
Using the Shooting Menu.........................................................77
Shooting Menu Options ............................................................78
T IMAGE QUALITY ..................................................................79
D WHITE BALANCE .................................................................79
H SHARPNESS ...........................................................................80
C PHOTOMETRY ......................................................................81
F AF MODE................................................................................81
S FACE RECOGNITION...........................................................82
J AE BKT EV STEPS .................................................................85
I FLASH......................................................................................85

Moviess
Movie
F Recording Movies ...................................................................57
a Viewing Movies .......................................................................59

Connectionss
Connection
Viewing Pictures on TV ...............................................................60
Printing Pictures via USB ...........................................................62
Connecting the Camera ............................................................62
Printing Selected Pictures ........................................................62
Printing the DPOF Print Order ................................................63
Creating a DPOF Print Order ....................................................65
Viewing Pictures on a Computer............................................68
Installing the Software...............................................................68
Connecting the Camera ............................................................72

xiv

Table of Contents
Using the Menus: Playback Mode ..........................................86
Using the F-Mode Menu..........................................................86
F-Mode Menu Options .............................................................86
I SLIDE SHOW .........................................................................87
Using the Playback Menu .........................................................88
Playback Menu Options.............................................................88
j MARK FOR UPLOAD ...........................................................89
B RED EYE REMOVAL .............................................................91
D PROTECT ................................................................................92
G CROP........................................................................................93
O RESIZE .....................................................................................94
C IMAGE ROTATE .....................................................................95
F VOICE MEMO ........................................................................96
The Setup Menu .............................................................................98
Using the Setup Menu ...............................................................98
Setup Menu Options...................................................................99
N TIME DIFFERENCE .............................................................101
K FORMAT............................................................................... 102
A IMAGE DISP. ....................................................................... 102
B FRAME NO. ......................................................................... 103
I PLAYBACK VOLUME ........................................................ 104
J LCD BRIGHTNESS ............................................................. 104
M AUTO POWER OFF ........................................................... 104
D DIGITAL ZOOM ................................................................. 104
P DISCHARGE (Ni-MH Batteries Only) ......................... 105

Technical Note
Notess
Optional Accessories ................................................................ 106
Accessories from FUJIFILM .................................................... 107
Caring for the Camera .............................................................. 108

Troubleshooting
Troubleshootin
g
Troubleshooting ......................................................................... 109
Warning Messages and Displays ..........................................116

Appendix
Appendi
x
Glossary ...........................................................................................120
Memory Card Capacity .............................................................121
Specifications ................................................................................122

Memo

xvi

Introduction
Symbols and Conventions

Menus and other text in the camera monitor are shown in bold. In the illustrations in this manual, the
monitor display may be simplified for explanatory purposes.

Before You Begin

The following symbols are used in this manual:
3 Caution: This information should be read before use to ensure correct operation.
1 Note: Points to note when using the camera.
2 Tip: Additional information that may be helpful when using the camera.

Supplied Accessories
The following items are included with the camera:

AA alkaline (LR6) batteries (×4)

USB-A/V cable

Strap

• Basic Manual
Lens cap

CD-ROM

Introduction

Parts of the Camera
For more information, refer to the page listed to the right of each item.

1
2
3
4
5
6

Strap eyelet .................................................... 7 7 F (photo mode) button ......................74, 86 12 Flash pop-up button .............................36
Zoom control...............................16, 47, 49 8 Indicator lamp ............................................19 13 Microphone ......................................... 57, 96
Shutter button ...........................................19 9 Mode dial ........................................................ 6 14 Speaker ................................................... 59, 97
g (Intelligent Face Detection) button .......31 10 AF-assist illuminator ...............................34 15 Lens .........................................................13, 122
I (burst mode) button ..............................40
Self-timer lamp ..........................................39
G switch ..........................................13 11 Flash..................................................................36

Introduction

20
21
22
23

Electronic viewfinder .................... 5
Selector button (see below)
Monitor ................................................... 4
DISP (display)/BACK button
....................................................17, 18, 46
a (playback) button ............... 20, 46
Tripod mount
Battery-chamber cover ................ 8
Battery-chamber latch.................. 8

24 EVF/LCD (display selection) button .... 5
25 d (exposure compensation/photo info)
button .......................................... 44, 48
26 Terminal cover..................60, 62, 72
27 Memory card slot ...........................11
28 Connector for USB-A/V cable
...................................................60, 62, 72
29 HDMI Mini Connector ................ 60

The Selector Button
Move cursor up
c (instant zoom) button (pg. 42)
b (delete) button (pg. 20)

Move cursor left
F (macro) button (pg. 35)

Before You Begin

16
17
18
19

MENU/OK button (pg. 14)

Move cursor right
N (flash) button (pg. 36)

Move cursor down
J (self-timer) button (pg. 38)

Introduction

Camera Displays
The following indicators may appear during shooting and playback. The indicators displayed vary with
camera settings.
■ Shooting
㧹

19
100

12/31/2050
10 : 00 AM
SET
250
F3. 1

1
2
3
4
5
6
7
8
9
10
11
12

Number of available frames........... 121
Image size .....................................................76
Focus warning ...........................................18
Silent mode .................................................18
Burst mode ..................................................40
Metering ........................................................81
Intelligent Face Detection
indicator .........................................................31
Shooting mode .........................................21
Flash mode...................................................36
Macro (close-ups) mode .....................35
Self-timer indicator .................................38
Focus frame .................................................81

13
14
15
16
17
18
19
20
21
22
23

Blur warning ............................36, 112, 116
Date and time.............................................14
Shutter speed and aperture .............26
Sensitivity ......................................................75
Image quality..............................................79
FinePix color ................................................77
White balance ............................................79
Battery level .................................................16
Dual IS mode ..............................................17
Exposure indicator ................................. 44
Exposure compensation
indicator ........................................................ 44

■ Playback
100-0001
100
4:3 N

12/31/2050 10 : 00 AM
1/250 F3.1

1
2
3
4

Gift image .....................................................46 7 DPOF print indicator ..............................65
Silent mode .................................................18 8 Voice memo indicator...........................96
Red-eye removal indicator ................91 9 Photobook assist indicator ................51
Intelligent Face Detection
10 Mark for upload to...................................89
indicator .........................................................31 11 Frame number ........................................ 103
5 Playback mode indicator ............20, 46 12 Rating...............................................................47
6 Protected image .......................................92

Introduction

EVF

LCD

Before You Begin

The Electronic Viewfinder (EVF)
The electronic viewfinder provides the same information as the monitor, and can be used when bright lighting conditions make the display in the monitor difficult to see. To switch between the monitor and electronic
viewfinder, press the EVF/LCD button (your selection remains in effect when the camera is turned off or the mode
dial is rotated to another setting).

Introduction

The Mode Dial
To select a shooting mode, align the mode icon with the mark next to the
mode dial.

B (AUTO): A simple “point-and-shoot”
mode recommended for first-time users
of digital cameras (pg. 21).

M (SCENE RECOGNITION): A “pointand-shoot” mode in which the camera
automatically adjusts settings to suit the
scene (pg. 15).

SP (SCENE POSITION): Choose a scene suited to the subject or shooting conditions
and let the camera do the rest (pg. 21).

P, S, A, M: Select for full control over camera settings, including aperture (M and A)
and/or shutter speed (M and S) (pg. 26).
C (CUSTOM): Recall stored settings for
modes P, S, A, and M (pg. 30).
F (MOVIE): Record movies with sound
(pg. 57).
N (MOTION PANORAMA): Take a series of
photographs and combine them to form
a panorama (pg. 24).

The Strap and Lens Cap
Attaching the Strap
Attach the strap to the two strap eyelets as shown
below.

The Lens Cap
Attach the lens cap as shown.

First Steps

To avoid losing the lens cap, pass the supplied
string through the eyelet (q) and secure the lens
cap to the strap (w).

3 Caution
To avoid dropping the camera, be sure the strap is correctly secured.

Inserting the Batteries
The camera takes four AA alkaline, lithium, or rechargeable Ni-MH batteries. A set of four alkaline batteries is supplied with the camera. Insert the batteries in the camera as described below.
the battery-chamber cover.
1 Open
Slide the battery-chamber latch in the direction shown and open
the battery-chamber
cover.
1 Note
Be sure the camera is off before opening the battery-chamber cover.
3 Cautions
• Do not open the battery-chamber cover when
the camera is on. Failure to observe this precaution could result in damage to image files or
memory cards.
• Do not use excessive force when handling the
battery-chamber cover.

Insert the batteries.
2 Insert
the batteries in the
orientation shown by the
“+“ and “–“ marks inside
the battery chamber.
3 Cautions
• Insert the batteries in the correct orientation.
• Never use batteries with peelBattery casing
ing or damaged casing or mix
old and new batteries, batteries with different charge levels,
or batteries of different types.
Failure to observe these
precautions could result
in the batteries leaking or
overheating.
• Never use manganese or Ni-Cd batteries.
• The capacity of alkaline batteries varies with the
manufacturer and drops at temperatures below
10 °C/50 °F; Ni-MH batteries are recommended.
• Fingerprints and other soil on the battery terminals can shorten battery life.

Inserting the Batteries

the battery-chamber cover.
3 Close
Close the battery-cham-

3 Caution
Do not use force. If the battery-chamber cover does not close, check that
the batteries are in the correct orientation and
try again.

First Steps

ber cover and slide it in
until the latch clicks into
place.

Choosing the Battery Type
SET-UP
5
After replacing the batteries
GUIDANCE DISPLAY
with batteries of a different type,
LITHIUM
VIDEO SYSTEM
ALKALINE
CUSTOM RESET
select the battery type using
BATTERY TYPE
NI-MH
DISCHARGE
the T BATTERY TYPE option
in the setup menu (pg. 100) to
ensure that the battery level is
displayed correctly and the camera does not turn off
unexpectedly.

2 Tip: Using an AC Power Adapter
The camera can be powered by an optional AC
power adapter and DC coupler (sold separately).

Inserting a Memory Card
The camera can store pictures on SD memory cards (sold separately) .
■ Compatible Memory Cards
SanDisk SD and SDHC memory cards have been approved for use in the camera. A complete list
of approved memory cards is available at http://www.fujifilm.com/products/digital_cameras/index.html.
Operation is not guaranteed with other cards. The camera can not be used with xD-Picture Cards or
MultiMediaCard (MMC) devices.
3 Caution
Memory cards can be locked, making it impossible to format the card or to record or delete
images. Before inserting a memory card, slide the write-protect switch to the unlocked position.
Write-protect
switch

Inserting a Memory Card

■ Inserting a Memory Card
Open the battery-chamber cover.

ber cover and slide it in
until the latch clicks into
place.

the memory card.
2 Insert
Holding the memory card in the orientation
shown below, slide it in until it clicks into
place at the back of the slot.

Click

Be sure card is in correct orientation; do not insert at an angle or
use force.

Removing Memory Cards
After confirming that the camera
is off, press the card in and then
release it slowly. The card can
now be removed by hand.

First Steps

1 Note
Be sure the camera is off
before opening the battery-chamber cover.

the battery-chamber cover.
3 Close
Close the battery-cham-

3 Cautions
• The memory card may spring out if you remove
your finger immediately after pushing the card in.
• Memory cards may be warm to the touch after being removed from the camera. This is normal and
does not indicate a malfunction.

Inserting a Memory Card
3 Cautions
• Do not turn the camera off or remove the memory card while the memory card is being formatted or data are being recorded to or
deleted from the card. Failure to observe this precaution could damage the card.
• Format memory cards before first use, and be sure to reformat all memory cards after using them in a computer
or other device. For more information on formatting memory cards, see page 102.
• Memory cards are small and can be swallowed; keep out of reach of children. If a child swallows a memory card,
seek medical assistance immediately.
• miniSD or microSD adapters that are larger or smaller than the standard dimensions of an SD card may not eject
normally; if the card does not eject, take the camera to an authorized service representative. Do not forcibly
remove the card.
• Do not affix labels to memory cards. Peeling labels can cause camera malfunction.
• Movie recording may be interrupted with some types of memory card. Use a y card or better when
shooting HD movies.
• Formatting a memory card in the camera creates a folder in which pictures are stored. Do not rename or delete
this folder or use a computer or other device to edit, delete, or rename image files. Always use the camera to
delete pictures from memory cards; before editing or renaming files, copy them to a computer and edit or rename the copies, not the originals.

Turning the Camera on and Off
Playback Mode

Slide the G switch in the direction shown
below. The lens will extend automatically.

To turn the camera on and begin playback, press
the a button for about a second.

Slide the G switch to turn the camera off.

Press the a button again or slide the G
switch to turn the camera off.

First Steps

Shooting Mode

2 Tip: Switching to Playback Mode
Press the a button to start playback. Press the shutter
button halfway to return to shooting mode.
3 Cautions
• Be sure that the lens cap is removed before turning
the camera on.
• Forcibly preventing the lens from extending could
cause damage or product malfunction.
• Pictures can be affected by fingerprints and other
marks on the lens. Keep the lens clean.
• The G button does not completely disconnect
the camera from its power supply.

2 Tip: Switching to Shooting Mode
To exit to shooting mode, press the shutter button
halfway. Press the a button to return to playback.

2 Tip: Auto Power Off
The camera will turn off automatically if no operations are performed for the length of time selected in the
M AUTO POWER OFF menu (see page 104). To turn the camera on, use the G switch or press the a
button for about a second.

Basic Setup
A language-selection dialog is displayed the first time the camera is turned on. Set up the camera as
described below (for information on resetting the clock or changing languages, see page 99).

1 Choose a language.1.1 Press the selector up or down to highlight a language.
START MENU

ENGLISH
FRANCAIS
DEUTSCH
ESPAÑOL
PORTUGUÊS
SET

1.2 Press MENU/OK.

2 Set the date and time.
2.1 Press the selector left or right to highlight the year, month, day,
DATE / TIME NOT SET
2013
2012
YY. MM. DD

SET

2011

2010
2009

1. 1

12 : 00
AM

hour, or minute and press up or down to change. To change
the order in which the year, month, and day are displayed, highlight the date format and press the selector up or down.
2.2 Press MENU/OK. A battery type message will be displayed; if the
type differs from the type inserted in the camera, use the setup
menu T BATTERY TYPE option (pg. 100) to specify the correct type.

2 Tip: The Camera Clock
If the batteries are removed for an extended period, the camera clock and battery type will be reset and the language-selection dialog will be displayed when the camera is turned on. If the batteries are left in the camera for
about 10 hours, the battery can be removed for about 24 hours without resetting the clock, language, or battery
type.

Taking Pictures in M (Scene Recognition) Mode
This section describes how to take pictures in M mode.
the camera on.
1 Turn
Slide the G switch to turn the camera
on.

• b (PORTRAIT): Human portrait Selected scene
subject.
• c (LANDSCAPE): Man-made or natural landscape.
• d (NIGHT): Poorly-lit landscape.
• e (MACRO): Subject close to camera.
• f (NIGHT PORTRAIT): Poorly-lit portrait subject.
• g (BACKLIT PORTRAIT): Back-lit portrait subject.
a (AUTO) is selected if none of the above are detected.

Basic Photography and Playback

Select M mode.
2 Rotate
the mode dial to M.

M
In this mode, the camera automatically analyzes the composition and selects a scene
according to shooting conditions and the type of subject:

Taking Pictures in M (Scene Recognition) Mode

the battery level.
3 Check
Check the battery level in the display.

the picture.
4 Frame
Use the zoom control to frame the picture in
the display.

Indicator
NO ICON
qB
(red)
wA
(blinks red)

Select T to zoom in

Description
Batteries are partially discharged.
Batteries are low. Replace as soon
as possible.
Batteries are exhausted. Turn camera off and replace batteries.

1 Note
A battery warning may not be displayed before
the camera turns off, particularly if batteries are
reused after having once been exhausted. Power
consumption varies greatly from mode to mode;
the low battery warning (B) may not be displayed or may be displayed only briefly before
the camera turns off in some modes or when
switching from shooting to playback mode.

Select W to zoom out
Zoom indicator

By default setting, the camera uses optical zoom only.
If desired, digital zoom
(pg. 104) can be used to
zoom in closer.
2 Tip: Focus Lock
Use focus lock (pg. 33) to focus on subjects that are not
in the focus frame.

Taking Pictures in M (Scene Recognition) Mode
Holding the Camera
Hold the camera steady with
both hands and brace your
elbows against your sides.
Shaking or unsteady hands
can blur your shots.
To prevent pictures that are
out of focus or too dark (underexposed), keep your fingers and other objects away
from the lens and flash.

Sensitivity is raised when dual IS is in effect. Note that
blurring may still occur depending on the scene. We
recommend that you turn dual IS off when using a
tripod.

Shooting Information
To choose the shooting information and guides displayed, press the DISP/BACK button.
Indicators displayed

Indicators hidden

HD framing

Best framing

Basic Photography and Playback

Avoiding Blurred Pictures
SET-UP
3
If the subject is poorly lit, blurLCD BRIGHTNESS
ring caused by camera shake
CONTINUOUS
EVF/LCD MODE
ONLY
AUTO POWERSHOOTING
OFF
can be reduced using the
DUAL IS OFF
MODE
RED EYE REMOVAL
BLINK_DETECTION
L DUAL IS MODE option in
the setup menu (pg. 100). In
B mode, blur caused by subject movement is also reduced (dual IS mode).

To use best framing, position the main subject at the
intersection of two lines or align one of the horizontal
lines with the horizon. When HD framing is used, 16:9
aspect ratio guide lines are displayed to make it easy
to frame HD shots. Use focus lock (pg. 33) to focus on
subjects that will not be in the center of the frame in
the final photograph.

Taking Pictures in M (Scene Recognition) Mode
Silent Mode
In situations in which camera sounds or lights may
be unwelcome, hold the DISP/BACK button down until
o is displayed (note that silent mode is not available
during movie or voice memo playback).

The camera speaker and AF-assist illuminator/selftimer lamp turn off and volume (pg. 99) can not be
adjusted (note that the AF-assist illuminator may still
light when C is selected in scene mode). To restore
normal operation, press the DISP/BACK button until the
o icon is no longer displayed.

Focus.
5 Press
the shutter button halfway
to focus.
1 Note
The lens may make a noise when the camera focuses; this is normal. In M mode, the camera continuously adjusts focus, increasing the
drain on the batteries.

If the camera is able to focus, it will beep twice
and the indicator lamp will glow green.
If the camera is unable to focus, the focus frame
will turn red, s will be displayed, and the
indicator lamp will blink green. Change the
composition or use focus lock (pg. 33).

Taking Pictures in M (Scene Recognition) Mode

Shoot.
6 Smoothly
press the shutter button
the rest of the way down to take
the picture.

Double
beep
q

Press halfway

Click
w

Press the rest of
the way down

1 Note
If the subject is poorly lit, the AF-assist illuminator may
light to assist focus (pg. 34). For information on using
the flash when lighting is poor, see page 36.

Indicator lamp
The indicator lamp shows camera status as follows:
Indicator lamp
Camera status
Glows green Focus locked.
Blur, focus, or exposure warning. PicBlinks green
ture can be taken.
Blinks green Recording pictures. Additional picand orange tures can be taken.
Glows
Recording pictures. No additional picorange
tures can be taken at this time.
Flash charging; flash will not fire when
Blinks orange
picture is taken.
Lens or memory error (memory card
Blinks red full or not formatted, format error, or
other memory error).

Basic Photography and Playback

2 Tip: The Shutter Button
The shutter button has two positions. Pressing the
shutter button halfway (q) sets focus and exposure;
to shoot, press the shutter button the rest of the way
down (w).

The Indicator Lamp

2 Tip: Warnings
Detailed warnings appear in the display. See pages
116–119 for more information.

Viewing Pictures
Pictures can be viewed in the monitor. When taking important photographs, take a test shot and
check the results.

1 Press the a button.

Deleting Pictures
To delete the picture currently displayed
in the monitor, press the selector up (b).
The following dialog will be displayed.
• Select FRAME and press MENU/
OK.

The most recent picture will be displayed in
the monitor.
100-0001

DIRECT ERASE
FRAME
SELECTED FRAMES
ALL FRAMES
SET

• To delete the picture, press
MENU/OK.

ERASE OK?

YES

additional pictures.
2 View
Press the selector right to view
pictures in the order recorded, left
to view pictures in reverse order.
Press the shutter button to exit to shooting
mode.
20

BACK

CANCEL

To exit without deleting the picture, press DISP/BACK.
2 Tip: The Playback Menu
Pictures can also be deleted from the playback menu
(pg. 54).

Shooting Mode
Choose a shooting mode according to the scene or type of subject. To choose a shooting mode, rotate
the mode dial to the desired setting (pg. 6). The following modes are available:

M SCENE RECOGNITION
The camera automatically analyzes the composition and selects the appropriate scene mode according to the subject and shooting conditions
(pg. 15).

B AUTO

the selector up or down to
3 Press
highlight A SCENE POSITION.
Press the selector right to display a
4 list
of scenes.
the selector up or down to
5 Press
highlight a scene.

SP SCENE POSITION
The camera offers a choice of “scenes,” each
adapted to particular shooting conditions or a
specific type of subject, which can be assigned to
the SP position on the mode dial:

1 Rotate the mode dial to SP.

MENU/OK to select the high6 Press
lighted option.
Until the setting is changed as described above,
the chosen scene will be selected whenever the
mode dial is rotated to SP.

More on Photography

Choose for crisp, clear snapshots. This mode is
recommended in most situations.

MENU/OK to display the shoot2 Press
ing menu.

Shooting Mode
Scene
B ZOOM BRACKETING
C NATURAL & N
D NATURAL LIGHT
C PORTRAIT
D BABY MODE
K SMILE&SHOOT
M LANDSCAPE
N SPORT
O NIGHT
H NIGHT (TRIPOD)
P FIREWORKS
Q SUNSET
R SNOW
S BEACH
U PARTY
V FLOWER
W TEXT

Description
The camera takes three shots: one at the current zoom ratio, a second zoomed in 1.4 ×, and a third
zoomed in 2 ×.
Get good results with backlit subjects and other difficult lighting. The camera takes two shots: one
without the flash and one with.
Capture natural light indoors, under low light, or where the flash can not be used.
Choose this mode for soft-toned portraits with natural skin tones.
Choose for natural skin tones when taking portraits of infants. The flash turns off automatically.
The shutter is released automatically when Intelligent Face Detection detects a smiling face.
Choose this mode for crisp, clear daylight shots of buildings and landscapes.
Choose this mode when photographing moving subjects. Priority is given to faster shutter speeds.
Choose this mode for poorly lit twilight or night scenes. Sensitivity is automatically raised to reduce
blur caused by camera shake.
Choose this mode for slow shutter speeds when shooting at night. Use a tripod to prevent blur.
Slow shutter speeds are used to capture the expanding burst of light from a firework. Press the d
button to display a shutter-speed selection dialog and press the selector up and down to choose a
shutter speed.
Choose this mode to record the vivid colors in sunrises and sunsets.
Choose for crisp, clear shots that capture the brightness of scenes dominated by shining white snow.
Choose for crisp, clear shots that capture the brightness of sunlit beaches.
Capture indoor background lighting under low-light conditions.
Choose for vivid close-ups of flowers. The camera focuses in the macro range.
Take clear pictures of text or drawings in print. The camera focuses in the macro range.

Shooting Mode

Wide

Tall

C Natural & N

This mode helps ensure good results with backlit
subjects and in other situations with difficult lighting. Before shooting, raise the flash; pictures can
only be taken when the flash is raised. Each time
the shutter button is pressed, the camera takes
two shots: one shot without the flash to preserve
natural lighting, followed immediately by a second shot with the flash. Do not move the camera
until shooting is complete.
1 Notes
• Do not use where flash photography is prohibited.
• Only available if memory remains for two pictures.
• Burst mode is not available.

D Natural Light
Capture natural light indoors, under low light, or
where the flash can not be used. The flash turns
off and sensitivity is raised to reduce blur.

More on Photography

B Zoom Bracketing
Each time the shutter button is pressed, the camera takes three pictures: one at the current zoom
ratio with an image size of O, a second zoomed
in 1.4 × and cropped to P, and a third zoomed in
2 × and cropped to Q (pictures will only be taken
if there is enough memory for three images). Two
frames are displayed to show the areas that will
be included in the second and third pictures; the
outer frame shows the area that will be recorded
at 1.4 × zoom, the inner frame the area that will be
recorded at 2 × zoom. Press the selector down to
choose from wide and tall crops.

1 Notes
• Digital zoom can not be used. If digital zoom is active
when B mode is selected, zoom will be set to the
maximum optical zoom position.
• Burst shooting options are limited to I and OFF.

Shooting Mode

N MOTION PANORAMA
In this mode, you can take up to three pictures and join them together to form a panorama. Use of a
tripod is recommended to assist in composing overlapping shots.
Rotate the mode dial to
1 N.

the next shot to overlap with the previ6 Frame
ous picture by superimposing y on + so that

2 Press MENU/OK to display the shooting menu.
C AUTO from
3 Select
P MODE in the shootSHOOTING MENU

they form a solid circle (z). The camera will
release the shutter automatically.
Pan direction

MODE

2 3

MANUAL
AUTO

ing menu (pg. 78).
5'6

END

Press the selector up to select a frame. Press
the selector left or right to highlight a pan direction and press MENU/OK.

Take a photograph. Ex5 posure
and white balance
for the panorama are set
with the first shot.
1 Note
The camera zooms all the way out and zoom remains fixed at the widest angle until shooting is
complete.

CANCEL

Display after 1st shot

END

CANCEL

Shutter released

7 Take the last shot as described in Step 6.
1 Note
To end shooting and create a panorama after the
first or second shot, press the multi selector up after
completing Step 5 or Step 6 and proceed to Step 8.

8 Press MENU/OK to save the picture.

Shooting Mode
Framing Panoramas Manually
Follow the steps below if the desired results are not
achieved with C AUTO selected for P MODE:
1 Select D MANUAL for P MODE in the shooting
menu.
2 Select a frame and take the first shot.
3 Press MENU/OK to display a guide showing an edge of
the picture you have just taken. Take the next shot,
framing it to overlap with the previous picture.
Guide

For Best Results
For best results, be careful not to tilt the camera backward or forward or to either side and try not to move
the camera while y and + are aligned to form a solid
circle.
Printing Panoramas
Depending on the page size and the size of the
panorama, panoramas may print with their edges
cropped out or with wide margins at the top and
bottom or at both sides.

4
5

Display after 1st shot
Frame next shot
Repeat Step 3 to take the third shot and then press
MENU/OK to display the completed panorama.
Press MENU/OK to save the picture.

More on Photography

3 Cautions
• Panoramas are created from multiple frames. The
camera may in some cases be unable to stitch the
frames together perfectly.
• The desired results may not be achieved with moving subjects, subjects close to the camera, unvarying
subjects such as the sky or a field of grass, subjects
that are in constant motion, such as waves and waterfalls, or subjects that undergo marked changes in
brightness. Panoramas may be blurred if the subject
is poorly lit.

Shooting Mode

P: PROGRAM AE
In this mode, the camera sets exposure automatically. If desired, you can choose different combinations of shutter speed and aperture that will
produce the same exposure (program shift).

Program Shift
Press the d button to choose the desired combination of shutter speed and aperture. Values that differ
from those automatically selected by the camera are
shown in yellow. The default values can be restored
by raising the flash or turning the camera off. Program shift is not available when the flash is raised.
Shutter speed
SET
250 F3. 1

3 Caution
If the subject is outside the metering range of the camera, the shutter speed and aperture displays
will show “---”. Press the shutter
button halfway to measure exposure again.

PROGRAM SHIFT
---F---

Aperture

Shooting Mode

S: SHUTTER PRIORITY AE
In this mode, you choose the shutter speed while the camera adjusts aperture for optimal exposure.

1 Rotate the mode dial to S.
2

Press the d button. Shutter speed
and aperture will be displayed.

Shutter speed
SET
250 F3.1

the selector up or down to
3 Press
choose the shutter speed.

Take pictures. If the correct exposure can not
5 be
achieved at the selected shutter speed, aperture will be displayed in red when the shutter button is pressed halfway. Adjust shutter speed until the correct exposure can be
achieved.
3 Caution
If the subject is outside the metering range of the camera, the aperture display will show “---”. Press the shutter button halfway to measure exposure again.

More on Photography

Press the d button to exit to shoot4 ing
mode.

Shooting Mode

A: APERTURE PRIORITY AE
In this mode, you choose the aperture while the camera adjusts shutter speed for optimal exposure.

1 Rotate the mode dial to A.
2

Press the d button. Shutter speed
and aperture will be displayed.
A

Aperture
SET
250 F3. 1

the selector up or down to
3 Press
choose the aperture.

Press the d button to exit to shoot4 ing
mode.
Take pictures. If the correct exposure can not
5 be
achieved at the selected aperture, shutter
speed will be displayed in red when the shutter button is pressed halfway. Adjust aperture
until the correct exposure can be achieved.
3 Caution
If the subject is outside the metering range of the camera, the shutter speed display will show “---”. Press the
shutter button halfway to measure exposure again.

Shooting Mode

M: MANUAL
In this mode, you choose both shutter speed and aperture. If desired, exposure can be altered from
the value suggested by the camera.

1 Rotate the mode dial to M.
2

Press the d button to exit to shoot5 ing
mode.

Press the d button. Shutter speed
and aperture will be displayed.

Shutter speed
SET
250 F3. 1

Aperture

the selector up or down to
3 Press
choose the shutter speed.
Press the selector left or right to
4 choose
the aperture.

The Exposure Indicator
The amount the picture will be under- or over-exposed at current settings is shown by the exposure
indicator. Pictures taken with the indicator to the left
of center (“–“) will be underexposed, pictures taken
with the indicator is to the right of center (“+”), overexposed.
M

More on Photography

6 Take pictures.

SET
250 F3. 1

Underexposed

Overexposed

Exposure indicator

Shooting Mode

C: CUSTOM MODE
In P, S, A, and M modes, the K CUSTOM SET option in the shooting
menu (pg. 78) can be used to save current camera and menu settings.
These settings are recalled whenever the mode dial is rotated to C (custom mode).
Menu/setting
Settings saved
F-mode menu N ISO, O IMAGE SIZE, P FINEPIX COLOR
T IMAGE QUALITY, C PHOTOMETRY, D WHITE BALANCE, F AF MODE, H SHARPNESS, I FLASH,
Shooting menu
J AE BKT EV STEPS, S FACE RECOGNITION
Setup menu A IMAGE DISP, L DUAL IS MODE, C AF ILLUMINATOR, D DIGITAL ZOOM, E EVF/LCD MODE
Shooting mode (P, S, A, or M), continuous shooting mode, Intelligent Face Detection, instant zoom, macro
Other
mode, exposure compensation, flash mode, shutter speed, aperture, display type (EVF/LCD), indicators/best
framing

Intelligent Face Detection
Intelligent Face Detection allows the camera to automatically detect human faces and set focus and
exposure for a face anywhere in the frame for shots that emphasize portrait subjects. Choose for
group portraits (in horizontal or vertical orientations) to prevent the camera from focusing on the background.
Intelligent Face Detection on.
1 Turn
Intelligent Face Detection is turned on or off

Focus.
3 Press
the shutter button halfway

each time g (Intelligent Face Detection) is
pressed.

to set focus and exposure for the
subject in the green border.

the picture.
2 Frame
If a face is detected, it
will be indicated by a
green border. If there is
more than one face in
the frame, the camera
Green border
will select the face closest to the center; other faces are indicated by
white borders.

Shoot.
4 Press
the shutter button all the
way down to shoot.

More on Photography

3 Caution
If no face is detected when the shutter button is
pressed halfway (pg. 111), the camera will focus
on the subject at the center of the display and
red-eye will not be removed.

3 Caution
If the subject moves as the shutter button is pressed, their face may not be in the area
indicated by the green border when the picture
is taken. If the number of faces is large, additional
time may be required for processing.

Intelligent Face Detection
Intelligent Face Detection
Intelligent Face Detection is
recommended when using
the self-timer for group- or
self-portraits (pg. 38).

Blink Detection
7

When a picture taken with Intelligent Face Detection
is displayed, the camera can automatically select faces
for red-eye removal (pg. 91), playback zoom (pg. 47),
slide shows (pg. 87), image search (pg. 53), image disp.
(pg. 102), printing (pg. 62), and cropping (pg. 93).

If an option other than OFF is selected for A IMAGE DISP. (pg. 102), a warning will be displayed
if the camera detects subjects who may have
blinked when the picture was taken. If ZOOM
(CONTINUOUS) is selected, you can press the g
button to zoom in on these subjects.
BLINK DETECTION

ZOOM UP
STORE

BLINK DETECTION

ERASE

NEXT
STORE

ERASE

3 Caution
Blink detection is not performed if the camera fails to
detect a face or when OFF is selected for A IMAGE
DISP..
2 Tip: Blink Detection
Blink detection can be turned on or off in the setup
menu (pg. 100).

Focus Lock
To compose photographs with off-center subjects:

1 Position the subject in the focus frame.

the picture.
3 Recompose
Keeping the shutter button pressed halfway,
recompose the picture.

cus and exposure. Focus and exposure will
remain locked while the shutter button is
pressed halfway (AF/AE lock).

Press
halfway

Shoot.
4 Press
the shutter-release button the rest of
the way down to take the picture.

Press the rest of
the way down

More on Photography

Focus.
2 Press
the shutter button halfway to set fo-

Repeat steps 1 and 2 as desired to refocus
before taking the picture.

Focus Lock
Autofocus
Although the camera boasts a high-precision autofocus system, it may be unable to focus on the subjects
listed below. If the camera is unable to focus using
autofocus, use focus lock (pg. 33) to focus on another
subject at the same distance and then recompose
the photograph.
• Very shiny subjects such • Fast-moving subjects.
as mirrors or car bodies.

• Subjects photographed through a window or other
reflective object.
• Dark subjects and subjects that absorb rather than
reflect light, such as hair or fur.
• Insubstantial subjects, such as smoke or flame.
• Subjects that show little contrast with the background (for example, subjects in clothing that is the
same color as the background).
• Subjects positioned in front of or behind a highcontrast object that is also in the focus frame (for
example, a subject photographed against a backdrop of highly contrasting elements).

The AF-Assist Illuminator
If the subject is poorly lit, the AF-assist illuminator will
light to assist the focus operation when the shutter
button is pressed halfway.
1 Notes
• Avoid shining the AF-assist illuminator directly into
your subject’s eyes.
• The camera may be unable to focus using the AFassist illuminator in some cases. If the camera is unable to focus in macro mode (pg. 35), try increasing
the distance to the subject.

F Macro and Super Macro Modes (Close-ups)
For close-ups, press the selector left (F) to choose from the macro options shown below.
Choose from F (macro mode),
G (super macro mode), or
OFF (macro mode off)

1 Notes
• Use of a tripod is recommended to prevent blur caused by camera shake.
• Flash compensation may be required when using the flash (pg. 85).
• Using the flash at close range may cast a lens shadow. Zoom a little or have more distance from the subject.

More on Photography

When macro mode is in effect, the camera focuses on subjects near the center of the frame. Use the
zoom control to compose pictures. In super macro mode, zoom can not be adjusted and the flash can
not be used.

N Using the Flash (Intelligent Flash)
When the flash is used, the camera’s Intelligent Flash system instantly analyzes the scene based on
such factors as the brightness of the subject, its position in the frame, and its distance from the camera.
Flash output and sensitivity are adjusted to ensure that the main subject is correctly exposed while
preserving the effects of ambient background lighting, even in dimly-lit indoor scenes. Use the flash
when lighting is poor, for example when shooting at night or indoors under low light.
the flash.
1 Raise
Press the flash pop-up button to raise the flash.
Turning the Flash Off
Lower the flash where flash photography is prohibited or to capture natural lighting
under dim light. At slow shutter speeds, k will be displayed to warn that pictures
may be blurred; use of a tripod is recommended.

a flash mode.
2 Choose
Press the selector right (N). The flash mode changes each time the selector
is pressed.

Mode
A/K
(AUTO FLASH)
N/L
(FORCED FLASH)
O/M
(SLOW SYNCHRO)

Description
The flash fires when required. Recommended in most situations.
The flash fires whenever a picture is taken. Use for backlit subjects or for natural
coloration when shooting in bright light.
Capture both the main subject and the background under low light (note that
brightly lit scenes may be overexposed).

N Using the Flash (Intelligent Flash)

Focus.
3 Press
the shutter button halfway to focus. If the flash will fire, p will be displayed when
the shutter button is pressed halfway. At slow shutter speeds, k will appear in the
display to warn that pictures may be blurred; use of a tripod is recommended.
Shoot.
4 Press
the shutter button the rest of the way down to shoot.

1 Note
The peripheral part of an image may be dark when using the flash.
Red-Eye Removal
When Intelligent Face Detection is active (pg. 31), and ON is selected for B RED EYE REMOVAL in
the setup menu (pg. 91), red-eye removal is available in K, L, and M.
Red-eye removal minimizes “red-eye” caused when light from the flash is reflected from the subject’s
retinas as shown in the illustration at right.

More on Photography

3 Caution
The flash may fire several times with each shot. Do not move the camera until shooting is complete.

J Using the Self-Timer
The camera offers a ten-second timer that allows photographers to appear in their own photographs,
and a two-second timer that can be used to avoid blur caused by the camera moving when the shutter
button is pressed. The self-timer is available in all shooting modes.
the timer.
1 Set
Press the selector down (h), and then press the selector left or right to highlight an option and
press MENU/OK.
OFF
OFF

Choose from
OFF (self-timer off),
S (10 s delay), or
R (2 s delay)

Focus.
2 Press
the shutter button halfway to focus.
3 Caution
Stand behind the camera when using the shutter button. Standing in front of the lens can interfere with focus and exposure.

the timer.
3 Start
Press the shutter button the rest of the way down to start the timer. The display shows the number of seconds remaining until the
shutter is released. To stop the timer before the picture is taken,
press DISP/BACK.

J Using the Self-Timer

The self-timer lamp on the front of the camera will blink
immediately before the picture is taken. If the two-second
timer is selected, the self-timer lamp will blink as the timer
counts down.

More on Photography

Intelligent Face Detection
Because it ensures that the faces of portrait subjects will be in focus, Intelligent Face Detection (pg. 31) is recommended when using the self-timer for group portraits or self-portraits. To use the self-timer with Intelligent Face
Detection, select S 10 SEC or R 2 SEC in the self-timer menu and then press the shutter button all the way
down to start the timer. The camera will detect faces while the timer is counting down and adjust focus and exposure immediately before the shutter is released. Be careful not to move until the picture has been recorded.
1 Note
The self-timer turns off automatically when the picture is taken, a different shooting mode is selected, playback
mode is selected, or the camera is turned off.

I Continuous Shooting (Burst Mode)
Capture motion in a series of pictures.
a continuous shooting mode.
1 Choose
Press the I button to display continuous shooting options. Press the selector g or h to highlight the desired option and press MENU/OK.
Mode

Description

Continuous shooting mode off. One picture is taken each time the shutOFF
ter button is pressed.
The camera takes up to 6 pictures while the shutter button is pressed.
I (TOP 6)
The camera takes up to 40 pictures while the shutter button is pressed,
L
but only the last 6 frames are recorded.
(FINAL 6)
The camera takes pictures while the shutter button is pressed. Shooting
N
(N LONG PERIOD) ends when the shutter button is released or memory is full.
K
The camera takes up to 20 pictures while the shutter button is pressed.
(K TOP 20)
J
The camera takes up to 40 pictures while the shutter button is pressed.
(J TOP 40)
Each time the shutter-release button is pressed, the camera takes three
shots: one using the metered value for exposure, the second overexposed by the amount selected for J AE BKT EV STEPS in the shootO
ing menu (pg. 85), and the third underexposed by the same amount (the
(AE BKT)
camera may not be able to use the selected bracketing increment if the
amount of over- or under-exposure exceeds the limits of the exposure
metering system).

CONTINUOUS

OFF
TOP6

I Continuous Shooting (Burst Mode)

Focus.
2 Press
the shutter button halfway to focus.
Shoot.
3 Pictures
will be taken while the shutter button is pressed.

Shooting ends when the
shutter button is released, memory is full, or the selected number of shots has been
taken.
More on Photography

1 Notes
• Focus and exposure are determined by the first frame in each series. The flash turns off automatically; the previously-selected flash mode is restored when continuous shooting is turned off.
• Frame rate varies with shutter speed.
• If the self-timer is used when L and N are selected, only one picture will be taken when the shutter button is
pressed.
• At a setting of J, white lines may appear in bright areas of the image; these can be avoided by choosing K
mode.
• The number of pictures that can be recorded depends on the memory available. AE bracketing is only available
if there is sufficient memory for three pictures. Additional time may be required to record pictures when shooting ends.

c Instant Zoom
In instant zoom, the area surrounding the frame is visible in the display. Use to frame erratically moving
subjects such as children, pets, and athletes at sporting events.
the subject in the focus frame.
1 Position
Use the zoom control to frame the subject in
the center of the display.

The frame is displayed as
shown at right. The composition can be adjusted
using the zoom control.
and shoot.
3 Focus
The framed area

will
be enlarged to create a
full-sized picture.

a frame.
2 Choose
Press the selector

2 Tip: Intelligent Face Detection
Intelligent Face Detection will not detect faces outside
the selected frame.

up
(c) to cycle through
framing options as
shown below.
Horizontal,
low zoom

Horizontal,
high zoom

Vertical,
high zoom

Vertical,
low zoom

No zoom

3 Caution
Only horizontal (landscape-orientation) framing is
available when I, L, N, or O is selected for continuous shooting mode.

c Instant Zoom

■ Digital Zoom
Enable digital zoom.
Select ON for the D DIGITAL ZOOM option in the setup menu (pg. 104).

the picture.
4 Frame
Use the zoom control to choose the area that
will be included in the final photograph.

a subject.
2 Choose
Frame the subject in the center of the display
using digital zoom.

the selector up (c).
3 Press
The camera will zoom to the maximum optical zoom position with the area that will be
recorded using digital zoom indicated by a
frame at the center of the display.

will
be enlarged to create a
full-sized picture.

3 Caution
Pictures taken using the instant zoom are lower quality
than pictures taken using normal zoom.

More on Photography

and shoot.
5 Focus
The framed area

d Exposure Compensation
Use exposure compensation when photographing very bright, very dark, or high-contrast subjects.
the d button.
1 Press
The exposure indicator will be displayed.

mode.

Exposure indicator
SET
250
F3.1

a value.
2 Choose
Press the selector left or right. The
effect is visible in the display.

Choose negative values Choose positive values to
to reduce exposure
increase exposure
(“–” sign turns yellow)
(“+” sign turns yellow)

to shooting mode.
3 Return
Press the d button to return to shooting

4 Take pictures.
1 Note
A d icon and exposure indicator are displayed at settings other than ±0. Exposure compensation is not
reset when the camera is turned off; to restore normal
exposure control, choose a value of ±0.

d Exposure Compensation
Choosing an Exposure Compensation Value
• Backlit subjects: choose values from +2/3 EV to +12/3 EV (for an explanation of the term “EV”,
see the Glossary on page 120)

• Highly reflective subjects or very bright scenes (e.g., snowfields): +1 EV

More on Photography

• Scenes that are mostly sky: +1 EV
• Spotlit subjects (particularly if photographed against dark backgrounds): –2/3 EV
• Subjects with low reflectivity (pine trees or dark-colored foliage): –2/3 EV

Playback Options
To view the most recent picture in the monitor,
press the a button.
100-0001

More on Playback

Press the selector right to view pictures
in the order recorded, left to view pictures in reverse order. Keep the selector
pressed to scroll rapidly to the desired
frame.

Choosing a Display Format
Press the DISP/BACK button to cycle through playback
display formats as shown below.

100-0001
100
4:3 N

12/31/2050 10 : 00 AM
1/250 F3.1

Information
on

100-0001

3
12/31/2050

10 : 00 AM

1 Note
Pictures taken using other cameras are indicated by a m (“gift image”) icon during playback.

Information
off

Favorites
(pg. 47)

Playback Options

Playback Zoom
Select T to zoom in on pictures displayed in single-frame playback; select W to zoom out. When
the picture is zoomed in, the selector can be used
to view areas of the image not currently visible in
the display.
Zoom indicator
Navigation window
shows portion of image
currently displayed in
monitor
1 Note
The maximum zoom ratio varies with image size.
Playback zoom is not available with copies resized or
cropped to a size of a.

I Favorites: Rating Pictures
To rate the picture currently displayed in full-frame
playback, press DISP/BACK and press the selector
up and down to select from zero to five stars.
2 Tip: Favorites
Ratings can be used for image search (pg. 53).

More on Playback

Press DISP/BACK to exit zoom.

Intelligent Face Detection
Pictures taken with Intelligent
Face Detection (pg. 31) are indicated by a g icon. Press the
g button to zoom in on the
ZOOM
BACK
subject selected with Intelligent Face Detection. You can
then use the zoom control to zoom in and out.

Playback Options

Viewing Photo Information
To view or hide the photo
information listed below
in single-frame playback,
press d.
4:3 N
ISO 400
F3.5
1/250
: STD
: OFF
:
: -1 2 3
12/31/2050 10 : 00 AM

100-0001

q Image quality and size, w Sensitivity, e Shutter speed/
aperture, r FinePix color, t Flash mode, y White balance, u Exposure compensation, i Frame number,
o Picture (overexposed areas blink on and off), !0 Histogram

Histograms
Histograms show the distribution of tones in the image. Brightness is shown by the horizontal axis, the
number of pixels by the vertical axis.
Optimal exposure: Pixels are
distributed in an even curve
throughout the tone range.
Overexposed: Pixels are clustered
at the right side of the graph.
Underexposed: Pixels are clustered
at the left side of the graph.

Playback Options

Multi-Frame Playback
To change the number of images displayed during playback, select W.

12/31/2050

2 Tip: Two-Frame Display
Two-frame display can be used
to compare pictures taken in
C mode.

10 : 00 AM

Select T to reduce
the number of images displayed.

More on Playback

Select W to
increase the
number of pictures
displayed to one
frame with previous and next, two,
nine, or a hundred.

Use the selector to highlight images and press
MENU/OK to view the highlighted image full frame.
In the nine- and hundred-frame displays, press
the selector up or down to view more pictures.

Viewing Panoramas
To view a panorama, display in single-frame view and press the selector down.

PLAY
STOP

PAUSE

The following operations can be performed during playback:
Operation
Start/pause
playback
End playback

Button

Description
Press the selector down to start playback. Press again to pause.

Press the selector up to end playback.

k PhotoBook Assist
Create books from your favorite photos.

Creating a PhotoBook
Select k PHOTOBOOK ASSIST in the play- 5 Scroll through the images and press the selec1 back
tor up to select or deselect the current image
menu.

2 Highlight NEW BOOK.

for inclusion in the book. To display the current
image on the cover, press the selector down.

MENU/OK to display the new
3 Press
book dialog.

1 Note
The first picture selected automatically becomes
the cover image. Press the selector down to select
a different picture for the cover.

pictures available.
• SELECT BY IMAGE SEARCH: Choose from pictures
matching selected search conditions (pg. 53).
1 Note
Neither photographs a or smaller nor movies can
be selected for photobooks.

MENU/OK to exit when the book
6 Press
is complete.

7 Highlight COMPLETE PHOTOBOOK.
SELECT IMAGES FOR PHOTOBOOK

SELECT ALL
COMPLETE PHOTOBOOK

More on Playback

pictures for the new book.
4 Choose
• SELECT FROM ALL: Choose from all the

EXIT

1 Note
Choose SELECT ALL to select all photos, or all photos matching the specified search conditions, for
the book.

k PhotoBook Assist

Press MENU/OK. The new book will be
8 added
to the list in the photobook
assist menu.
3 Cautions
• Photobooks can contain up to 300 pictures.
• Books that contain no photos are automatically
deleted.
PhotoBooks
Photobooks can be copied to a computer using the
supplied MyFinePix Studio software.

Viewing PhotoBooks
Highlight a book in the photobook assist menu
and press MENU/OK to display the book, then press
the selector left and right to scroll through the
pictures. Press DISP/BACK to return to the photobook assist menu.

Editing and Deleting PhotoBooks
Display the photobook and press
1 MENU/OK
to view book edit options.
from the following options:
2 Choose
• EDIT: Edit the book as described in “Creating a
PhotoBook” on page 51.
• ERASE: Delete the current photobook.

3 Follow the on-screen instructions.

b Image Search
Search for pictures by date, subject, scene, file type, and rating.
b IMAGE SEARCH in the playback 3 Select a search condition. Only pictures that
1 Select
menu.
match the search condition will be displayed.

one of the following options and
2 Highlight
press MENU/OK:
Option

Option
A ERASE
D PROTECT
I SLIDE SHOW

See page
54
92
87

4 To end the search, select EXIT SEARCH.

More on Playback

Description
Find all pictures taken on a selected
BY DATE
date.
Find all pictures based on specified face
BY FACE
information.
Find all pictures with a specified rating
BY I FAVORITES
(pg. 47).
Find all pictures that match a selected
BY SCENE
scene.
BY TYPE OF DATA Find all still pictures or all movies.
Find all pictures selected for upload to a
BY UPLOAD MARK
specified destination (pg. 89).

To delete or protect selected pictures or to
view the selected pictures in a slide show,
press MENU/OK and choose from the following
options:

A Deleting Pictures
In the playback menu, you can select and delete
individual pictures or delete all pictures at once.
Note that deleted pictures cannot be recovered.
Copy important pictures to a computer or other
storage device before proceeding.
Press the MENU/OK button to display the playback
menu, and then select the desired method for deleting pictures on the A ERASE screen.
PLAYBACK MENU
PHOTOBOOK BACK
ASSIST
FRAME
IMAGE SEARCH
ERASE SELECTED FRAMES
MARK FOR
ALLUPLOAD
FRAMES
SLIDE SHOW
RED EYE REMOVAL

1 /2

Delete one picture
Delete multiple
pictures
Delete all pictures

Deleting One Picture
Press g or h to select the desired picture and
then press the MENU/OK button to delete the picture that is displayed.
2 Tips
• The picture is deleted when the MENU/OK button is
pressed, so be careful not to accidentally delete pictures.
• Pressing the MENU/OK button repeatedly will delete
consecutive pictures. Press g or h to select the
picture that you want to delete before you press the
MENU/OK button.

A Deleting Pictures

Deleting Multiple Pictures
All pictures marked with a
checkmark
can be deleted
at once.

Select OK and press the MENU/OK
3 button
to delete the selected pictures.

2 Tip
Pictures that have been selected
for a DPOF print order and protected pictures are indicated by u.

Select each picture you want to de1 lete
and press the MENU/OK button.

selecting all the pictures you
2 After
want to delete, press the DISP/BACK

More on Playback

• Each picture will be marked with a
checkmark .
• Press the MENU/OK button again to
remove the checkmark.

button.
A confirmation screen is displayed.

A Deleting Pictures

Deleting All Pictures
You can delete all the pictures.
2 Tips
• You can press the DISP/BACK button to cancel, however, pictures that were deleted before you pressed the DISP/
BACK button cannot be recovered.
• Protected pictures cannot be deleted. Remove protection from any pictures that you want to delete (pg. 92).
• A message is displayed if you try to delete pictures that have been selected for a DPOF print order. To delete the
pictures, press the MENU/OK button.

F Recording Movies
Shoot short movies at 30 frames per second. Sound is recorded via the built-in microphone; do not
cover the microphone during recording.
Rotate the mode dial to F (movie
1 mode).
12s
STANDBY

Time available
is displayed in
monitor

the F button and select a frame size
2 Press
from the O QUALITY menu. Choose h 1280

MENU/OK and select F AF MODE.
3 •Press
r CENTER: The camera focuses on the subject in the center of the screen.
• u CONTINUOUS: Use when shooting a
moving subject. The camera continuously
focuses on the subject as it moves within the
AF frame.

Zooming While Recording a Movie
The zoom can be used while recording a movie.
In the setup menu, select 1 DIGITAL or 2 OPTICAL
(pg. 100).
1 DIGITAL: Image quality may deteriorate when
the zoom is used.
2 OPTICAL: The sound of the camera zooming
may be heard when playing movie.
Avoiding Blurred Pictures
If the subject is poorly lit, blurring caused by camera
shake can be reduced using the L DUAL IS MODE
option in the setup menu (pg. 100).

Movies

(1280 × 720 pixels) for an aspect ratio of 16 : 9 (High
Definition), f (640 × 480 pixels) for high-quality
standard definition movies, or g (320 × 240 pixels) for longer movies. Press MENU/OK to exit to
movie mode.

MENU/OK. The camera returns to the mov4 iePress
recording screen.

Sensitivity is raised when dual IS is in effect. Note that
blurring may still occur depending on the scene. We
recommend that you turn dual IS off when using a
tripod.

F Recording Movies

the shutter button all the way
5 Press
down to start recording.
REC

12s

z REC and time
remaining are displayed in monitor

1 Note
Exposure and white balance are adjusted automatically
throughout recording. The color and brightness of the
image may vary from that displayed before recording
begins.
2 Tip
There is no need to keep the shutter button pressed
during recording.

Press the shutter button halfway to
6 end
recording. Recording ends automatically when the movie reaches
maximum length or memory is full.

3 Caution
The indicator lamp lights while movies are being recorded. Do not open the battery chamber during
shooting or while the indicator lamp is lit. Failure to
observe this precaution could prevent the movie from
being played back.
1 Notes
• Vertical or horizontal streaks may appear in movies
containing very bright subjects. This is normal and
does not indicate a malfunction.
• The E EVF/LCD MODE option in the setup menu is
fixed at 30 fps in movie mode.
• Recording movies for a long time or using the camera
at high ambient temperatures may increase the camera temperature. This is normal and does not indicate
a malfunction.

a Viewing Movies
During playback (pg. 46),
movies are displayed in the
monitor as shown at right.
The following operations
can be performed while a
movie is displayed:
Operation
Start/pause
playback
End
playback/
delete

100-006

Progress is shown in the monitor during playback.
15s

12/31/2050
PLAY

10 : 00 AM

STOP

PAUSE

2 Tip: Viewing Movies on a Computer
Copy movies to the computer before viewing.
3 Caution
Do not cover the speaker during playback.

Movies

Description
Press the selector down to start playback.
Press again to pause.
Press the selector up to end playback. If
playback is not in progress, pressing the
selector up will delete the current movie.
Press the selector right to advance, left to
Advance/ rewind. If playback is paused, the movie
rewind will advance or rewind one frame each
time the selector is pressed.
Press MENU/OK to pause playback and disAdjust play volume controls. Press the selector
volume up or down to adjust the volume; press
MENU/OK again to set the volume.

Progress bar

Viewing Pictures on TV
Connect the camera to a TV to show pictures to a group.

1 Turn the camera off.
2 Connect the supplied USB-A/V cable as shown below.
Insert into USB-A/V
cable connector

Connect yellow plug
to video-in jack
Connect white plug
to audio-in jack

HDMI
An HDMI cable (available from third-party suppliers; pg. 125) can be used to connect the camera to High
Definition (HD) devices (playback only). The USB cable can not be used while an HDMI cable is connected.

Connections

Insert into HDMI
connector

HDMI Mini Connector

Insert into HDMI
connector

Viewing Pictures on TV

Tune the television to the video or HDMI input channel. See the documentation supplied with the
3 television
for details.
Press the a button for about a second to turn the camera on. The camera monitor turns off and
4 pictures
and movies are played back on the TV. Note that the camera volume controls have no effect on sounds played on the TV; use the television volume controls to adjust the volume.
1 Note
Image quality drops during movie playback.
3 Caution
When connecting the cable, be sure the connectors are fully inserted.

Connections

Printing Pictures via USB
If the printer supports PictBridge, the camera can be connected directly to the printer and
pictures can be printed without first being copied to a computer. Note that depending on
the printer, not all the functions described below may be supported.

Connecting the Camera

Printing Selected Pictures

the supplied USB-A/V cable as shown 1 Press the selector left or right to dis1 Connect
play a picture you wish to print.
and turn the printer on.
the selector up or down to
2 Press
choose the number of copies (up to
99).

Press the a button for about a second to turn
the camera on. t USB will be displayed in
the monitor, followed by the PictBridge display
shown below at right.
USB

steps 1–2 to select additional
3 Repeat
pictures. Press MENU/OK to display a
confirmation dialog when settings
are complete.
PRINT THESE FRAMES
TOTAL: 9 SHEETS

PICTBRIDGE
TOTAL: 00000
YES

00 SHEETS
FRAME
OK

SET

CANCEL

4 Press MENU/OK to start printing.

Printing Pictures via USB
2 Tip: Printing the Date of Recording
To print the date of recording on pictures, press DISP/
BACK in steps 1–2 to display the PictBridge menu (see
“Printing the DPOF Print Order,” below). Press the selector up or down to highlight PRINT WITH DATE s
and press MENU/OK to return to the PictBridge display
(to print pictures without the date of recording, select
PRINT WITHOUT DATE).
1 Note
If no pictures are selected when the MENU/OK button is
pressed, the camera will print one copy of the current
picture.

Printing the DPOF Print Order
To print the print order created with K PRINT
ORDER (DPOF) in the playback F-mode menu
(pg. 86):
In the PictBridge display, press DISP/
1 BACK
to open the PictBridge menu.
PICTBRIDGE
PRINT WITH DATE
PRINT WITHOUT DATE
PRINT DPOF

the selector up or down to
2 Press
highlight u PRINT DPOF.

PRINT DPOF OK?
TOTAL: 9 SHEETS

YES

Connections

Press MENU/OK to display a confirma3 tion
dialog.

CANCEL

Printing Pictures via USB

4 Press MENU/OK to start printing.
During Printing
The message shown at right
is displayed during printing.
Press DISP/BACK to cancel before all pictures are printed
(depending on the printer,
printing may end before the
current picture has printed).

PRINTING

CANCEL

If printing is interrupted, press a to turn the camera
off and then on again.
Disconnecting the Camera
Confirm that “PRINTING” is not displayed in the monitor and turn the camera off. Disconnect the USB
cable.

1 Notes
• Print pictures from a memory card that has been formatted in the camera.
• If the printer does not support date printing, the
PRINT WITH DATE s option will not be available in
the PictBridge menu and the date will not be printed
on the pictures in the DPOF print order.
• When pictures are printed via direct USB connection,
page size, print quality, and border selections are
made using the printer.

Printing Pictures via USB

Creating a DPOF Print Order
The K PRINT ORDER (DPOF) option in the playback F-mode menu can be used to create a digital “print order” for PictBridge-compatible printers
(pg. 62) or devices that support DPOF.
DPOF
DPOF (Digital Print Order Format) is standard
that allows pictures to be printed from “print
orders” stored on a memory card. The information in the order includes the pictures to
be printed, date imprint, and the number of copies of
each picture.

■ WITH DATE s// WITHOUT DATE
To modify the DPOF print order, select K PRINT
ORDER (DPOF) in the playback F-mode menu
and press the selector up or down to highlight
WITH DATE s or WITHOUT DATE.
MODE MENU
WITH DATE
WITHOUT
DATE
PHOTOBOOK
ASSIST
SLIDE SHOW
RESET ALL
PRINT ORDER (DPOF)

WITH DATE s: Print date of recording on pictures.
WITHOUT DATE: Print pictures without
date.

Press MENU/OK and follow the steps below.
Press the selector left or right to dis1 play
a picture you wish to include in
Connections

or remove from the print order.

Printing Pictures via USB

the selector up or down to
2 Press
choose the number of copies (up to
99). To remove a picture from the
order, press the selector down until the number of copies is 0.
PRINT ORDER (DPOF)
DPOF: 00001

Total number of prints
Number of copies

Repeat steps 1–2 to complete the
3 print
order. Press MENU/OK to save
the print order when settings are
complete, or DISP/BACK to exit without changing the print order.
The total number of prints is dis4 played
in the monitor. Press MENU/OK
to exit.

01 SHEETS
FRAME

SET

2 Tip: Intelligent Face Detection
If the current picture was created with Intelligent
Face Detection, pressing g sets the number of
copies to the number of faces detected.
1 Note
When pictures are printed via direct USB connection, page size, print quality, and border selections
are made using the printer.

The pictures in the current
print order are indicated by a
u icon during playback.

Printing Pictures via USB
1 Notes
• Print orders can contain a maximum of 999 pictures.
RESET DPOF OK?
• If a memory card is inserted
containing a print order created by another camera, the
message shown at right will
YES
NO
be displayed. Pressing MENU/
OK cancels the print order; a
new print order must be created as described above.

■ RESET ALL
RESET DPOF OK?
To cancel the current print
order, select RESET ALL
in the K PRINT ORDER
(DPOF) menu. The confirYES
CANCEL
mation shown at right will
be displayed; press MENU/OK to remove all pictures
from the order.

Connections

Viewing Pictures on a Computer
The supplied software can be used to copy pictures to a computer, where they can be stored, viewed,
organized, and printed. Before proceeding, install the software as described below. Do NOT connect the
camera to the computer until installation is complete.

Installing the Software
Two applications are supplied: MyFinePix Studio for Windows and FinePixViewer for the Macintosh.
Installation instructions for Windows are on pages 68–69, those for the Macintosh on pages 70–71.
Windows: Installing MyFinePix Studio
Confirm that the computer meets the following system requirements:

CPU
RAM
Free disk space
Video
Other

•
•
•
•

Windows 7 *
Windows Vista *
Windows XP *
3 GHz Pentium 4 or better
2 GHz Pentium 4 or better
1 GB or more
512 MB or more
15 GB or more
2 GB or more
1024 × 768 pixels or more with 24-bit color or better
A graphics processing unit (GPU) that supports DirectX 7 or later
Built-in USB port recommended. Operation is not guaranteed with other USB ports.
Internet connection (broadband recommended) required to install .NET Framework (if necessary), to use
auto update feature, and when performing such tasks as sharing pictures on-line or via e-mail.

* Other versions of Windows are not supported. Only pre-installed operating systems are supported; operation is not
guaranteed on home-built computers or computers that have been upgraded from earlier versions of Windows.

Viewing Pictures on a Computer

2 Start the computer. Log in to an account with administrator privileges before proceeding.
3 Exit any applications that may be running and insert the installer CD in a CD-ROM drive.
Windows 7/Windows Vista
If an AutoPlay dialog is displayed, click SETUP.EXE. A “User Account Control” dialog will then be displayed;
click Yes (Windows 7) or Allow (Windows Vista).

The installer will start automatically; click Install MyFinePix Studio and follow the on-screen instructions to install MyFinePix Studio.
If the Installer Does Not Start Automatically
If the installer does not start automatically, select Computer or My Computer from the Start menu, then
double-click the FINEPIX CD icon to open the FINEPIX CD window and double-click setup or SETUP.EXE.

prompted to install Windows Media Player, DirectX, or .NET Framework, follow the on-screen in4 Ifstructions
to complete installation.

number is printed at the top of the CD label for reference when updating the software or contacting
customer support.
Installation is now complete. Proceed to “Connecting the Camera” on page 72.

Connections

Remove the installer CD from the CD-ROM drive when installation is complete. Store the installer
5 CD
in a dry location out of direct sunlight in case you need to re-install the software. The version

Viewing Pictures on a Computer

Macintosh: Installing FinePixViewer
Confirm that the computer meets the following system requirements:

CPU

PowerPC or Intel
Pre-installed versions of Mac OS X version 10.3.9–10.6
OS
(for the latest information, visit http://www.fujifilm.com/)
RAM
256 MB or more
Free disk space A minimum of 200 MB required for installation with 400 MB available when FinePixViewer is running
Video
800 × 600 pixels or more with thousands of colors or better
Other
Built-in USB port recommended. Operation is not guaranteed with other USB ports.

After starting the computer and quitting any applications that may be running, insert the installer
2 CD
in a CD-ROM drive and double-click Installer for Mac OS X.
installer dialog will be displayed; click Installing FinePixViewer to start installation. Enter an
3 An
administrator name and password when prompted and click OK, then follow the on-screen instructions to install FinePixViewer. Click Exit to quit the installer when installation is complete.

Viewing Pictures on a Computer

the installer CD from the CD-ROM drive. Note that you may be unable to remove the CD
4 ifRemove
Safari is running; if necessary, quit Safari before removing the CD. Store the installer CD in a dry
location out of direct sunlight in case you need to re-install the software. The version number is
printed at the top of the CD label for reference when updating the software or contacting customer
support.
OS X 10.5 or earlier: Open the “Applications” folder, start Image Capture, and select Preferences…
5 Mac
from the Image Capture application menu. The Image Capture preferences dialog will be displayed;
choose Other… in the When a camera is connected, open menu, then select FPVBridge in the
“Applications/FinePixViewer” folder and click Open. Quit Image Capture.
Mac OS X 10.6: Connect the camera and turn it on. Open the “Applications” folder and start Image
Capture. The camera will be listed under DEVICES; select the camera and choose FPVBridge from
the Connecting this camera opens menu and click Choose. Quit Image Capture.
Installation is now complete. Proceed to “Connecting the Camera” on page 72.
Connections

Viewing Pictures on a Computer

Connecting the Camera
If the pictures you wish to copy are stored on a 3 Press the a button for about a second to
1 memory
card, insert the card into the camera
turn the camera on. MyFinePix Studio or
(pg. 11).
1 Note
Windows users may require the Windows CD when
starting the software for the first time.
3 Caution
Loss of power during transfer could result in loss of
data or damage to the memory card. Insert fresh
or fully-charged batteries before connecting the
camera.

Turn the camera off and connect the supplied
USB cable as shown, making sure the connectors are fully inserted. Connect the camera directly to the computer; do not use a USB hub
or keyboard.

FinePixViewer will start automatically; follow
the on-screen instructions to copy pictures to
the computer. To exit without copying pictures, click Cancel.
3 Caution

If the software does not start automatically, it may
not be correctly installed. Disconnect the camera
and reinstall the software.

For more information on using the supplied software, start the application and select the appropriate option from the Help menu.

Viewing Pictures on a Computer
3 Cautions

Disconnecting the Camera
After confirming that the indicator lamp is out, follow
the on-screen instructions to turn the camera off and
disconnect the USB cable.
Uninstalling the Supplied Software
Only uninstall the supplied software when it is no longer required or before beginning reinstallation. After
quitting the software and disconnecting the camera,
drag the “FinePixViewer” folder from “Applications”
into the Trash and select Empty Trash in the Finder
menu (Macintosh), or open the control panel and use
“Programs and Features” (Windows 7/Windows Vista)
or “Add or Remove Programs” (Windows XP) to uninstall MyFinePix Studio. Under Windows, one or more
confirmation dialogs may be displayed; read the contents carefully before clicking OK.
Connections

• If a memory card containing a large number of images
is inserted, there may be a delay before the software
starts and you may be unable to import or save images. Use a memory card reader to transfer pictures.
• Make sure that the computer does not display a message stating that copying is in progress and that the
indicator lamp is out before turning the camera off or
disconnecting the USB cable (if the number of images copied is very large, the indicator lamp may remain
lit after the message has cleared from the computer
display). Failure to observe this precaution could result in loss of data or damage to the memory card.
• Disconnect the camera before inserting or removing
memory cards.
• In some cases, it may not be possible to access pictures
saved to a network server using the supplied software
in the same way as on a standalone computer.
• The user bears all applicable fees charged by the
phone company or Internet service provider when
using services that require an Internet connection.

Using the Menus: Shooting Mode
The F-mode and shooting menus contain settings for a wide range of shooting conditions.

Using the F-Mode Menu
Press the F button to display the F1 mode
menu.
the selector up or down to
2 Press
highlight the desired menu item.
Press the selector right to display op3 tions
for the highlighted item.

Menus

the selector up or down to
4 Press
highlight the desired option.
MENU/OK to select the high5 Press
lighted option.
DISP/BACK
6 Press
menu.

to exit from the

Using the Menus: Shooting Mode

F-Mode Menu Options
Menu item

Description

N ISO

Adjust ISO sensitivity. Choose higher values when the subject is poorly lit.

O IMAGE SIZE

Choose image size and aspect ratio (pg. 76).

P FINEPIX COLOR

Shoot pictures in standard or saturated color or in black-andwhite (pg. 77).

Options
AUTO / AUTO (800) / AUTO (400) /
6400 Q / 3200 Q / 1600 /
800 / 400 / 200 / 100 / 64
O 4 : 3 / O 3 : 2 / O 16 : 9 /
P 4 : 3 / P 3 : 2 / P 16 : 9 /
Q 4 : 3 / Q 3 : 2 / Q 16 : 9

Default

c/a/b

AUTO

O4:3

N ISO
Control the camera’s sensitivity to light. Higher values can be used to reduce blur when lighting is
poor; note, however, that mottling may appear in pictures taken at high sensitivities. If AUTO, AUTO
(800), or AUTO (400) is selected, the camera will adjust sensitivity automatically in response to shooting conditions. The maximum values that will be selected by the camera at settings of AUTO (800)
and AUTO (400) are 800 and 400 respectively. Settings other than AUTO are shown by an icon in the
display.

Menus

1 Note
Sensitivity is not reset when the camera is turned off or another shooting mode is selected.

Using the Menus: Shooting Mode

O IMAGE SIZE
Choose the size and aspect ratio at which still pictures are recorded. Large pictures can be printed
at large sizes with no drop in quality; small pictures require less memory, allowing more pictures
to be recorded.
Option
O4:3
O3:2
O 16 : 9
P4:3
P3:2
P 16 : 9
Q4:3
Q3:2
Q 16 : 9

Prints at sizes up to
34 × 25 cm (13.5 × 10 in.)
34 × 23 cm (13.5 × 9 in.)
34 × 19 cm (13.5 × 7.5 in.)
24 × 18 cm (9.5 × 7 in.)
24 × 16 cm (9.5 × 6 in.)
24 × 13 cm (9.5 × 5.5 in.)
17 × 13 cm (7 × 5 in.)
17 × 12 cm (7 × 4.5 in.)
16 × 9 cm (6.5 × 3.5 in.)

The number of pictures that can be taken at the
selected setting is shown in the display (pg. 121).

Aspect Ratio
Pictures with an aspect ratio of 4 : 3 have the same
proportions as the camera display. Pictures with an
aspect ratio of 3 : 2 have the same proportions as a
frame of 35-mm film, while an aspect ratio of 16 : 9 is
suited to display on High Definition (HD) devices.

4:3

3:2

16 : 9

1 Note
Image size is not reset when the camera is turned off or
another shooting mode is selected.

Using the Menus: Shooting Mode

P FINEPIX COLOR
Enhance contrast and color saturation or take pictures in black and white.
Option

Description
Standard contrast and saturation.
F-STANDARD
Recommended in most situations.
Vivid contrast and color. Choose
for vivid shots of flowers or enF-CHROME
hanced greens and blues in landscapes.
Take pictures in black and white.
F-B&W

Settings other than F-STANDARD are shown by
an icon in the display.

MENU/OK to display the shoot1 Press
ing menu.
the selector up or down to
2 Press
highlight the desired menu item.
Press the selector right to display op3 tions
for the highlighted item.
the selector up or down to
4 Press
highlight the desired option.
MENU/OK to select the high5 Press
lighted option.
DISP/BACK
6 Press
menu.

to exit from the

Menus

1 Notes
• FINEPIX COLOR is not reset when the camera is
turned off or another shooting mode is selected.
• The effects of F-CHROME vary from scene to
scene and may be difficult to discern with some
subjects. Depending on the subject, the effects of
F-CHROME may not be visible in the display.

Using the Shooting Menu

Using the Menus: Shooting Mode

Shooting Menu Options
Menu item
A SCENE POSITION

Choose a scene for SP mode (pg. 21).

N ISO

Adjust ISO sensitivity. Choose higher values when the
subject is poorly lit.

O IMAGE SIZE

Choose image size and aspect ratio (pg. 76).

T IMAGE QUALITY

Choose image quality (pg. 79).
Shoot pictures in standard or saturated color or in blackand white (pg. 77).

P FINEPIX COLOR
D WHITE BALANCE

Adjust color for different light sources (pg. 79).

H SHARPNESS
C PHOTOMETRY
F AF MODE

Choose whether to sharpen or soften outlines (pg. 80).
Choose how the camera meters exposure (pg. 81).
Choose how the camera selects a focus area (pg. 81).
Choose whether the camera automatically detects and
sets focus and exposure for human portrait subjects
(pg. 82).
Choose how panoramas are framed (pg. 24).
Choose the size of the bracketing increment when O is
selected in continuous shooting mode (pg. 85).

S FACE RECOGNITION
P MODE
J AE BKT EV STEPS

Description

I FLASH

Adjust flash brightness (pg. 85).

K CUSTOM SET

Save settings for P, S, A, and M modes (pg. 30).

Options

Default

B/C/D/C/D/K/M/
N/O/H/P/Q/R/S/U/
V/W

AUTO / AUTO (800) / AUTO (400) /
6400 Q / 3200 Q / 1600 /
800 / 400 / 200 / 100 / 64
O4:3/O3:2/O16:9/
P4:3/P3:2/P16:9/
Q4:3/Q3:2/Q16:9
FINE/NORMAL

NORMAL

c/a/b

AUTO/h/i/j/
k/l/m/n
HARD / STD / SOFT
o /p /q
r /s /t /u /x

AUTO

O4:3

AUTO
STD
o
r

—

C/D
1/3

2/3

± EV / ± EV / ±1 EV
2/3

2/3

– EV – + EV
in steps of 1/3 EV
—

C
1/3

0
—

Using the Menus: Shooting Mode

T IMAGE QUALITY
Choose how much image files are compressed.
Select FINE (low compression) for higher image
quality, NORMAL (high compression) to increase
the number of pictures that can be stored.

D WHITE BALANCE
For natural colors, choose a setting that matches
the light source (for an explanation of “white balance,” see the Glossary on page 120).
Option
AUTO
h
i
j
k
l
m
n

Description
White balance adjusted automatically.
Measure a value for white balance.
For subjects in direct sunlight.
For subjects in the shade.
Use under “daylight” fluorescent lights.
Use under “warm white” fluorescent lights.
Use under “cool white” fluorescent lights.
Use under incandescent lighting.

If AUTO does not produce the desired results (for
example, when taking close-ups), select h and
measure a value for white balance or choose the
option that matches the light source.
Menus

1 Notes
• At settings other than h, auto white balance is used
with the flash. Lower the flash (pg. 36) to take pictures at other settings.
• Results vary with shooting conditions. Play pictures
back after shooting to check colors in the monitor.

Using the Menus: Shooting Mode

■ h: Custom White Balance
Choose h to adjust white balance for unusual
lighting conditions. White balance measurement
options will be displayed; frame a white object so
that it fills the monitor and press the shutter button all the way down to measure white balance.
If “COMPLETED!” is displayed, press MENU/OK to set
white balance to the measured value. This value
can be reselected by pressing MENU/OK when custom white balance options are displayed.
If “UNDER” is displayed, raise exposure compensation (pg. 44) and try again.
If “OVER” is displayed, lower exposure compensation and try again.
2 Tip
To give a deliberate color cast to your photographs,
measure a value for custom white balance using a colored instead of a white object.

H SHARPNESS
Choose whether to sharpen or soften outlines.
• HARD: Use for sharp outlines when photographing such subjects as buildings and text.
• STANDARD: Standard sharpness. Best choice in
most situations.
• SOFT: Use for soft outlines in portraits and similar
subjects.

Using the Menus: Shooting Mode

C PHOTOMETRY
Choose how the camera meters exposure when
Intelligent Face Detection is off.
• o MULTI: Automatic scene recognition is used
to adjust exposure for a wide range of shooting
conditions.
• p SPOT: The camera meters lighting conditions
at the center of the frame. Recommended when
the background is much brighter or darker than
the main subject. Can be used with focus lock
(pg. 33) to meter off-center subjects.
• q AVERAGE: Exposure is set to the average for
the entire frame. Provides consistent exposure
across multiple shots with the same lighting,
and is particularly effective for landscapes and
portraits of subjects dressed in black or white.

F AF MODE
This option controls how the camera selects the
focus area when Intelligent Face Detection is off
(pg. 31). Regardless of the option selected, the
camera will focus on the subject in the center of
the monitor when macro mode is on (pg. 35).
• r CENTER: The camera focuses on the subject in
the center of the frame. This option can be used
with focus lock (pg. 33).
• s MULTI: When the shutter button is pressed
halfway, the camera detects high-contrast subjects near the center of the frame and selects
the focus area automatically (if the focus frame is
not displayed, select r CENTER and use focus
lock; pg. 33).
Press
halfway

PROGRAM SHIFT
F2. 8

Focus frame

Menus

Using the Menus: Shooting Mode
SELECT AF AREA
• t AREA: The focus position
can be chosen manually by
pressing the selector up,
down, left, or right and pressSET
CANCEL
ing MENU/OK when the focus
brackets are in the desired position. Choose for
precise focus when the camera is mounted on a
tripod. Note that exposure is set for the subject
in the center of the frame; to meter an off-center
subject, use AF/AE lock (pg. 33).
• u CONTINUOUS: The camera continually adjusts
focus to reflect changes in the distance to the
subject even when the shutter button is not
pressed (note that this increases the drain on the
battery).
• x TRACKING: Position the P
subject in the center focus
area and press the selector
START TRACKING
left to select tracking. Focus
PROGRAM SHIFT
250
F3. 1
will track the subject as it
moves through the frame.

S FACE RECOGNITION
Once personal information is registered with a
face, the camera recognizes the registered face
and prioritizes focus and exposure to that face.
When playing back the face, the registered information (name, birthday, etc.) can be displayed.
■ REGISTER
REGISTER from S FACE RECOGNI1 Select
TION.
MENU/OK to turn to shooting
2 Press
mode.
the shutter button to shoot.
3 Press
Capture a front face.
REGISTER FACE

CAPTURE THE FACE
ALONG WITH THE GUIDLINE

CANCEL

MENU/OK to display PERSONAL
4 Press
INFO.
82

Using the Menus: Shooting Mode
A Note
When the message !CANNOT REGISTER is displayed,
the camera has failed to register the face. Take a shot
again.

■ VIEW & EDIT

Press the selector left or right to
2 highlight
a face to view or edit.

• NAME: Enter a name of up to 14 characters
and press MENU/OK.
• BIRTHDAY: Enter the subject’s date of birth and
press MENU/OK.
• CATEGORY: Choose the option that describes
your relationship to the subject and press
MENU/OK.

MENU/OK to display PERSONAL
3 Press
INFO.
the registration or edit as the same way
4 View
of REGISTER (pg. 82).
A Notes
• Select REPLACING IMAGE to take another face image and replace the registered image with it.
• To delete face recognition data, select ERASE from
S FACE RECOGNITION.

Menus

A Notes
• If shooting date matches the birthday of the peson
with the green border during face zoom, Happy
Birthday! will be displayed with the name.
• If D BABY MODE is selected in the shooting mode
and Intelligent Face Detection is on, the camera will
display the age of a 3 year old or younger child.
• To disable face recognition, set FACE RECOGNITION
to OFF.

Select VIEW & EDIT from S FACE RECOGNI1 TION
to display REGISTERED FACE.

Using the Menus: Shooting Mode

■ AUTO REGISTRATION
Select AUTO REGISTRATION from S FACE
RECOGNITION and set it to ON. After shooting
the same face several times with 3 FACE DETECTION turned on, the camera automatically
recognizes the face.
A Notes
• When the camera recognizes a face that has been
shot many times, the message REGISTER THIS PERSON? appears. Press MENU/OK to display PERSONAL
INFO so that you can register the face and its personal information.
• Using only AUTO REGISTRATION may be difficult to
recognize a face. In that case, register a face and its
personal information from REGISTER.

S FACE RECOGNITION
• Up to 8 people’s information can be registered.
• When 8 people’s information has already been registered, AUTO REGISTRATION does not function.
• If the camera detects two or more faces registered
by S FACE RECOGNITION, a green border and
orange border(s) will be displayed on the faces
when to shoot. A registered name will appear only
on the face with the green border. White borders
will be displayed on faces which have not been
registered. When no name has been registered,
“---” is displayed.
• S FACE RECOGNITION may not function in the
following:
- the subject does not face front.
- the face is not positioned within a frame.
- the feature of the face varies (because of age or
expression).
- the subject is in back-lit or poorly light.

Using the Menus: Shooting Mode
Removing face recognition during playback
Select S ERASE FACE RECOG. in the playback menu
(pg. 88). When this option is selected, the camera will
zoom in on an area in the current picture that it has
matched with a face in the face recognition database.
If the match is not correct, press MENU/OK to remove
the link to the face recognition database.
1 Note
Face recognition links cannot be removed from copies resized or cropped to a size of a.

J AE BKT EV STEPS
Choose the size of the exposure bracketing increment used when O (AE bracketing) is selected in
continuous shooting mode (pg. 40).
Choose from increments of ±1/3 EV, ±2/3 EV, and
±1 EV (for an explanation of the term “EV,” see the
Glossary on page 120).
I FLASH
Adjust flash brightness. Choose from values between +2/3 EV and –2/3 EV. The default setting is ±0.
Note that the desired results may not be achieved
depending on shooting conditions and the distance to the subject.

Menus

Using the Menus: Playback Mode
The F-mode and playback menus are used to manage the pictures on the memory card.

Using the F-Mode Menu

F-Mode Menu Options

the a button to enter play1 Press
back mode.

Option
k PHOTOBOOK
ASSIST
I SLIDE SHOW
K PRINT ORDER
(DPOF)

Press the F button to display the F2 mode
menu.
the selector up or down to
3 Press
highlight the desired menu item.
Press the selector right to display op4 tions
for the highlighted item.
the selector up or down to
5 Press
highlight the desired option.
MENU/OK to select the high6 Press
lighted option.

Description
Create books from your favorite photos
(pg. 51).
View pictures in a slide show (pg. 87).
Select pictures for printing on DPOF- and
PictBridge-compatible devices (pg. 63).

Using the Menus: Playback Mode

I SLIDE SHOW
View pictures in an automated slide show. Choose the type of show and press MENU/OK to start. Press
DISP/BACK at any time during the show to view on-screen help. When a movie is displayed, movie playback will begin automatically, and the slide show will continue when the movie ends. The show can
be ended at any time by pressing MENU/OK.
Option
NORMAL
FADE-IN
NORMAL g
FADE-IN g
MULTIPLE

Displayed in
Press selector left or right to go back or skip ahead one frame. Select FADE-IN for fade transitions between
frames.
As above, except that camera automatically zooms in on faces selected with Intelligent Face detection.
Display several pictures at once.

1 Note
The camera will not turn off automatically while a slide show is in progress.

Menus

Using the Menus: Playback Mode

Using the Playback Menu

Playback Menu Options

the a button to enter play1 Press
back mode.

The following options are available:

Press MENU/OK to display the play2 back
menu.
the selector up or down to
3 Press
highlight the desired menu item.
Press the selector right to display op4 tions
for the highlighted item.
the selector up or down to
5 Press
highlight the desired option.
MENU/OK to select the high6 Press
lighted option.

Option

Description
Create books from your favorite photos
(pg. 51).
Search for pictures by date, subject,
b IMAGE SEARCH
scene, file type, or rating (pg. 53).
A ERASE
Delete all or selected pictures (pg. 54).
Select pictures for upload to YouTube
j MARK FOR UPLOAD
or FACEBOOK (pg. 89).
View pictures in a slide show (pg. 87).
I SLIDE SHOW
Create copies with reduced red eye
B RED EYE REMOVAL
(pg. 91).
Protect pictures from accidental deleD PROTECT
tion (pg. 92).
Create cropped copies of pictures
G CROP
(pg. 93).
Create small copies of pictures (pg. 94).
O RESIZE
C IMAGE ROTATE
Rotate pictures (pg. 95).
F VOICE MEMO
Add voice memos to pictures (pg. 96).
Remove face recognition links from
S ERASE FACE RECOG.
the current image (pg. 85).
K PRINT ORDER
Select pictures for printing on DPOF- and
(DPOF)
PictBridge-compatible devices (pg. 63).
k PHOTOBOOK ASSIST

Using the Menus: Playback Mode

j MARK FOR UPLOAD
You can select images and movies to be queued for upload to YouTube and FACEBOOK.
Select j MARK FOR UPLOAD in the playback menu.
■ Add/Remove Items in the Upload Queue

1 Select an upload destination.
2 Press MENU/OK.
Select items to be added to, or re3 moved
from, the upload queue.

steps 3 and 4 as necessary
5 Repeat
and add or remove items.
When finished, press DISP/BACK to
save the settings.
2 Tips
• YouTube or FACEBOOK is displayed to indicate items
queued for upload.
• Only movies can be queued for upload to YouTube.

MENU/OK to confirm.
4 Press
• Items not in the upload queue will

Menus

be added to the queue when you
select them and press MENU/OK.
• Items in the upload queue will be
removed from the queue when you
select them and press MENU/OK.

Using the Menus: Playback Mode

■ Removing All Items From the Upload Queue
You can remove all items from the upload queue.
Select RESET ALL.
1 The
screen for removing all items
from the upload queue is displayed.

■ Upload Items
Items added to the upload queue using the camera can be easily uploaded from a computer by
using the MyFinePix Studio.
Install MyFinePix Studio (pg. 68).

RESET ALL OK?
IT MAY TAKE A WHILE

OK
CANCEL
SET

2 Select OK.
MENU/OK.
3 Press
All items are removed from the upload queue.
1 Note
If there are many items in the upload queue when you
select to remove all items from the queue, it may take
some time to remove them. To cancel, press DISP/BACK.

1 Note
This feature is available only when using a computer
running Windows.

Using the Menus: Playback Mode

B RED EYE REMOVAL
If the current picture is marked with a g icon to indicate that it was taken with Intelligent Face Detection, this option can be used to remove red-eye. The camera will analyze the image; if red-eye is
detected, the image will be processed to create a copy with reduced red-eye.
REMOVAL OK?

YES

REMOVING

CANCEL

1 Notes
• Red eye may not be removed if the camera is unable to detect a face or the face is in profile. Results may differ
depending on the scene. Red eye can not be removed from pictures that have already been processed using
red-eye removal or pictures created with other devices.
• The amount of time needed to process the image varies with the number of faces detected.
• Copies created with B RED EYE REMOVAL are indicated by a e icon during playback.

Menus

Using the Menus: Playback Mode

D PROTECT
Protect pictures from accidental deletion. The following options are available.
■ FRAME
Protect selected pictures.
Press the selector left or right to dis1 play
the desired picture.
PROTECT OK?

YES

UNPROTECT OK?

CANCEL

Picture not protected

YES

CANCEL

Protected picture

MENU/OK to protect the picture.
2 Press
If the picture is already protected,
pressing MENU/OK will remove protection from the image.
steps 1–2 to protect addi3 Repeat
tional images. Press DISP/BACK to exit
when the operation is complete.

■ SET ALL
Press MENU/OK to protect all
pictures, or press DISP/BACK
to exit without changing
picture status.
■ RESET ALL
Press MENU/OK to remove protection from all pictures, or
press DISP/BACK to exit without changing picture status.

SET ALL OK?
IT MAY TAKE A WHILE

YES

CANCEL

RESET ALL OK?
IT MAY TAKE A WHILE

YES

CANCEL

If the number of pictures affected is very large, a
message will be displayed while the operation is
in progress. Press DISP/BACK to exit before the operation is complete.
3 Caution
Protected pictures will be deleted when the memory
card is formatted (pg. 102).

Using the Menus: Playback Mode

G CROP
To create a cropped copy of a picture, play the picture back and select G CROP in the playback menu
(pg. 88).
Use the zoom control to zoom in and out and 2 Press MENU/OK to view the copy size.
1 use
the selector to scroll the picture until the
Larger crops produce larger copies;
desired portion is displayed (to exit to singleframe playback without creating a cropped
copy, press DISP/BACK).
Zoom indicator
CROP

YES

CANCEL

Navigation window
shows portion of
image currently displayed in monitor

all copies have an aspect ratio of
4 : 3.
MENU/OK to save the cropped
3 Press
copy to a separate file.
1 Note
Pictures taken with other cameras can not be cropped.

If the size of the final copy will be a, YES will
be displayed in yellow.
CROP

CROP
YES

Menus

2 Tip: Intelligent Face Detection
If the picture was shot with
Intelligent Face Detection
(pg. 31), g will be displayed
in the monitor. Press the g
button to zoom in on the
selected face.

CANCEL

Using the Menus: Playback Mode

O RESIZE
To create a small copy of a picture, play the picture back and select O RESIZE in the playback menu
(pg. 88).
the selector up or down to
1 Press
highlight a or b.

MENU/OK to select the high2 Press
lighted option.
Press MENU/OK to copy the picture at
3 the
selected size.

Using the Menus: Playback Mode

C IMAGE ROTATE
By default, pictures taken in tall orientation are
displayed in wide orientation. Use this option to
display pictures in the correct orientation in the
monitor. It has no effect on pictures displayed on
a computer or other device.

Press the selector down to rotate the
1 picture
90 ° clockwise, up to rotate
the picture 90 ° counterclockwise.

1 Notes
• Protected pictures can not be rotated. Remove protection before rotating pictures (pg. 92).
• The camera may not be able to rotate pictures created with other devices.

To rotate a picture, play the picture back and select C IMAGE ROTATE in the playback menu
(pg. 88).

MENU/OK to confirm the opera2 Press
tion (to exit without rotating the picture, press DISP/BACK).
The next time the picture is played back, it will
automatically be rotated.
Menus

Using the Menus: Playback Mode

F VOICE MEMO
To add a voice memo to a still picture, select
F VOICE MEMO after displaying the picture in
playback mode.
1 Note
Voice memos can not be added to movies or protected pictures. Remove protection from pictures before
recording voice memos (pg. 92).

2 Press MENU/OK to start recording.
28s

RECORDING

Time remaining
Blinks red

REC

RE-REC

the camera at a distance of about 20 cm 3 Press MENU/OK again to end record1 (8Hold
ing. Recording ends automatically
in.) and face the microphone.
after 30 seconds.

Microphone

1 Notes
• If a voice memo already exists for the current picture, a message will be displayed. Select RE-REC to replace the
existing memo.
• Voice memos are recorded as PCM-format WAV files.

Using the Menus: Playback Mode

Playing Voice Memos
To play back a voice memo, select a picture for which a voice memo
has been recorded (i.e., a picture indicated by q), and then select PLAY
on the F VOICE MEMO screen in the playback menu.
To end playback, press the selector up. Press the selector left to rewind,
right to fast forward. Volume controls can be displayed by pressing the
MENU/OK button; press the selector up or down to adjust the volume,
and press MENU/OK again to resume playback.

15s

STOP

PAUSE

Progress is shown
in the monitor.
Progress bar

1 Notes
• The camera may not play voice memos recorded with other devices.
• To replace a voice memo with a new voice memo, select RE-REC on the F VOICE MEMO screen in the playback menu.
3 Caution
Do not cover the speaker during playback.

Menus

Speaker

The Setup Menu
Using the Setup Menu
the setup menu.
1 Display
1.1 Press MENU/OK to display

the

menu for the current mode.
1.2 Press the selector left to highlight a left tab.
1.3 Press the selector up or down
to select 4.
The setup menu appears.
SET-UP
DATE/TIME
TIME DIFFERENCE
SILENT MODE
RESET
FORMAT

Adjust settings.
2 2.1
Press the selector right to activate the setup menu.
2.2 Press the selector up or down
to highlight a menu item.
2.3 Press the selector right to display options for the highlighted
item.

1 /5

ENGLISH
OFF

2.4 Press the selector up or down
to highlight an option.

EXIT

2.5 Press MENU/OK to select the
highlighted option.
2.6 Press DISP/BACK to exit from the
menu.

The Setup Menu

Setup Menu Options
Menu item
F DATE/TIME
N TIME DIFFERENCE
La

Description
Options
Set the camera clock (pg. 14).
—
Set the clock to local time (pg. 101).
h/g
Choose a language (pg. 14).
—
Disables the AF-assist illuminator (except for the C shooting
ON / OFF
o SILENT MODE
mode), operation sounds, shutter sound, and movie playback
1/5
sound.
Reset all settings except F DATE/TIME, N TIME DIFFERENCE,
O BACKGROUND COLOR, T BATTERY TYPE, and Q VIDEO SYSTEM to
—
R RESET
default values. A confirmation dialog will be displayed, press
the selector up or down to highlight OK and press MENU/OK.
Format memory cards (pg. 102).
—
K FORMAT
Choose how long pictures are displayed after shooting
3 SEC / 1.5 SEC /
A IMAGE DISP.
(pg. 102).
ZOOM / OFF
B FRAME NO.
Choose how files are named (pg. 103).
CONT. / RENEW
Adjust the volume of camera controls.
G OPERATION VOL.
b (high) / c (mid) /
2/5
d (low) / eOFF (mute)
H SHUTTER VOLUME Adjust the volume of the shutter sound.
Choose the sound made by the shutter.
e SHUTTER SOUND
i/j
Adjust the volume for movie and voice memo playback
—
I PLAYBACK VOLUME
(pg. 104).

Default
—
h
ENGLISH
OFF

—
—
1.5 SEC
CONT.
c
i
7

Menus

The Setup Menu
Menu item
J LCD BRIGHTNESS

Description
Control the brightness of the display (pg. 104).
Choose 30 fps to increase battery life, 60 fps for improved disE EVF/LCD MODE
play quality.
Choose the auto power off delay (pg. 104).
M AUTO POWER OFF
3/5
Enable image stabilization during shooting (l CONTINUOUS) or
L DUAL IS MODE
only when the shutter button is pressed halfway (m SHOOTING
ONLY). OFF turns image stabilization off (pg. 17).
B RED EYE REMOVAL Remove “red-eye” effects caused by the flash.
m BLINK DETECTION
Turn blink detection on or off (pg. 32).
D DIGITAL ZOOM
Enable or disable digital zoom (pg. 104).
l MOVIE ZOOM TYPE Choose the zoom type when recording movies (pg. 57).
C AF ILLUMINATOR
Turn the AF-assist illuminator on or off (pg. 34).
Choose whether to save unprocessed copies of pictures taken
4/5 n SAVE ORG IMAGE
using red-eye removal.
Choose ON to automatically rotate “tall” (portrait-orientation)
m AUTOROTATE PB
pictures during playback.
O BACKGROUND COLOR Choose a color scheme.
c GUIDANCE DISPLAY Choose whether to display tool tips.
Choose a video mode for connection to a TV (pg. 60).
Q VIDEO SYSTEM
Reset all settings for mode C. A confirmation dialog will be
5/5 S CUSTOM RESET
displayed, press the selector up or down to highlight OK and
press MENU/OK.
Specify the type of battery used in the camera (pg. 9).
T BATTERY TYPE
Discharge rechargeable Ni-MH batteries (pg. 105).
P DISCHARGE

100

Options
–5 – +5

Default
0

30 fps / 60 fps

30 fps

2 MIN / 5 MIN / OFF

2 MIN

l / m / OFF

ON / OFF
ON / OFF
ON / OFF
1/2
ON / OFF

ON
ON
OFF
1
ON

ON / OFF

OFF

ON / OFF

—
ON / OFF
NTSC / PAL

—
ON
—

—

x/y/z
—

x
—

The Setup Menu

N TIME DIFFERENCE
When travelling, use this option to switch the camera clock instantly from your home time zone to the
local time at your destination.
the difference between local time
1 Specify
and your home time zone.
1.1 Press the selector up or down
to highlight g LOCAL.
1.2 Press the selector right to display the time difference.
1.3 Press the selector left or right
to highlight +, –, hours, or minutes; press up or down to edit.
The minimum increment is 15
minutes.

To set the camera clock to local time, highlight g LOCAL and press MENU/OK. To set
the clock to the time in your home time
zone, select h HOME. If g LOCAL is selected, g will be displayed in the monitor
for three seconds after the camera enters
shooting mode, and the date will be displayed in yellow.

12/31/2050

10 : 00 AM

After changing time zones, check that the
date and time are correct.

Menus

1.4 Press MENU/OK when settings
are complete.

Switch between local time and your home
2 time
zone.

101

The Setup Menu

K FORMAT
Format a memory card. Highlight OK and press
MENU/OK to begin formatting.
3 Cautions
• All data—including protected pictures—will be deleted. Be sure important files have been copied to a
computer or other storage device.
• Do not open the battery cover during formatting.

102

A IMAGE DISP.
Choose an option other than OFF to display pictures in the monitor after shooting. Pictures can
be displayed for 1.5 s (1.5 SEC), 3 s (3 SEC), or until
the MENU/OK button is pressed (ZOOM (CONTINUOUS)). If ZOOM (CONTINUOUS) is selected,
photos can be zoomed in to check focus and
other fine details (see page 47). Note that ZOOM
(CONTINUOUS) is disabled in continuous shooting mode (pg. 40), and that the colors displayed
at settings of 1.5 SEC and 3 SEC may differ from
those in the final picture.
When the picture is zoomed in, the selector can
be used to view areas of the image not currently
visible in the display.
When the picture was taken with g FACE DETECTION turned on, detected face is zoomed. When
more than one face was detected, you can move
to the next face by pressing g.
ZOOM (CONTINUOUS) is disabled in the following case:
• C / B is selected in the shooting mode.
• An option other than OFF is selected for
I CONTINUOUS.

The Setup Menu
Blink Detection (pg. 32)
At settings other than OFF, a warning will be displayed if the camera detects subjects who may have
blinked when the picture was taken. If ZOOM (CONTINUOUS) is selected, you can view these subjects
using zoom.

B FRAME NO.
New pictures are stored in Frame number
image files named using a
100-0001
four-digit file number assigned by adding one to the Directory
File
last file number used. The number number
file number is displayed during playback as shown at right. B FRAME NO.
controls whether file numbering is reset to 0001
when a new memory card is inserted or the current memory card is formatted.
• CONTINUOUS: Numbering continues from the last
file number used or the first available file number, whichever is higher. Choose this option to
reduce the number of pictures with duplicate
file names.
• RENEW: Numbering is reset to 0001 after formatting or when a new memory card is inserted.
Menus

1 Notes
• If the frame number reaches 999-9999, the shutter
release will be disabled (pg. 117).
• Selecting R RESET (pg. 99) resets B FRAME NO. to
CONTINUOUS but does not reset frame numbering.
• Frame numbers for pictures taken with other cameras may differ.

103

The Setup Menu

I PLAYBACK VOLUME
Press the selector up or down to choose volume
for movie and voice memo playback and press
MENU/OK to select.
J LCD BRIGHTNESS
Press the selector up or down to choose display
brightness and press MENU/OK to select.
M AUTO POWER OFF
Choose the length of time before the camera
turns off automatically when no operations are
performed. Shorter times increase battery life;
if OFF is selected, the camera must be turned
off manually. Note that regardless of the option
selected, the camera will not turn off automatically when connected to a printer (pg. 62) or computer (pg. 72) or when a slide show is in progress
(pg. 87).
2 Tip: Reactivating the Camera
To reactivate the camera after it has turned off automatically, use the G switch or press the a button for about a second (pg. 13).

104

D DIGITAL ZOOM
If ON is selected, selecting T at the maximum
optical zoom position will trigger digital zoom,
further magnifying the image. To cancel digital
zoom, zoom out to the minimum digital zoom
position and select W.
Zoom
indicator

Zoom indicator,
DIGITAL ZOOM off
W

Zoom indicator,
DIGITAL ZOOM on
T W

Optical zoom

T
Digital
zoom

3 Caution
Digital zoom produces lower quality images than optical zoom.

The Setup Menu

P DISCHARGE (Ni-MH Batteries Only)
The capacity of rechargeable Ni-MH batteries may be temporarily reduced when new, after long periods of disuse, or if they are repeatedly recharged before being fully discharged. Capacity can be increased by repeatedly discharging the batteries using the P DISCHARGE option and recharging
them in a battery charger (sold separately). Do not use P DISCHARGE with non-rechargeable batteries, and note that the batteries will not discharge if the camera is powered by an optional AC power
adapter and DC coupler.
Selecting P DISCHARGE displays a
1 confirmation
dialog. Press MENU/OK.

2 Select OK.

MENU/OK to begin discharging the batter3 Press
ies. When the batteries are fully discharged,
the battery level indicator will blink red and
the camera will turn off. To cancel the process
before the batteries are fully discharged, press
DISP/BACK.

Menus

105

Optional Accessories
The camera supports a wide range of accessories from FUJIFILM and other manufacturers.
■ Audio/Visual
Standard TV (available from
third-party suppliers)
USB-A/V cable

FINEPIX
S4000/S4000A/S3900 Series
S3400/S3300/S3200 Series

HDTV (available from
third-party suppliers)

USB-A/V cable
Computer (available from
third-party suppliers)

HDMI cable
Technical Notes

SD/SDHC
memory card

■ Printing
USB-A/V cable

PictBridge-compatible printer
(available from third-party suppliers)

106

■ Computer Related

SD card slot or card reader

Printer (available from
third-party suppliers)

Optional Accessories

Accessories from FUJIFILM
The following optional accessories are available from FUJIFILM. For the latest information on the accessories available in your region, check with your local FUJIFILM representative or visit http://www.fujifilm.
com/products/digital_cameras/index.html.
AC power adapter AC-5VX (requires
CP-04 DC coupler)
DC coupler

CP-04

Use for extended playback or when copying pictures
to a computer (shape of adapter and plug vary with
region of sale).
Connect the AC-5VX AC power adapter to the camera.

Technical Notes

107

Caring for the Camera
To ensure continued enjoyment of the product, observe the following precautions.
Storage and Use
If the camera will not be used for an extended period, remove the battery and memory card. Do
not store or use the camera in locations that are:
• exposed to rain, steam, or smoke
• very humid or extremely dusty
• exposed to direct sunlight or very high temperatures, such as in a closed vehicle on a sunny day
• extremely cold
• subject to strong vibration
• exposed to strong magnetic fields, such as near
a broadcasting antenna, power line, radar emitter, motor, transformer, or magnet
• in contact with volatile chemicals such as pesticides
• next to rubber or vinyl products
■ Water and Sand
Exposure to water and sand can also damage the
camera and its internal circuitry and mechanisms.
When using the camera at the beach or seaside,
avoid exposing the camera to water or sand. Do
not place the camera on a wet surface.
108

■ Condensation
Sudden increases in temperature, such as occur
when entering a heated building on a cold day,
can cause condensation inside the camera. If this
occurs, turn the camera off and wait an hour before turning it on again. If condensation forms on
the memory card, remove the card and wait for
the condensation to dissipate.
Cleaning
Use a blower to remove dust from the lens and
monitor, then gently wipe with a soft, dry cloth.
Any remaining stains can be removed by wiping
gently with a piece of FUJIFILM lens-cleaning paper to which a small amount of lens-cleaning fluid
has been applied. Care should be taken to avoid
scratching the lens or monitor. The camera body
can be cleaned with a soft, dry cloth. Do not use
alcohol, thinner, or other volatile chemicals.
Traveling
Keep the camera in your carry-on baggage.
Checked baggage may suffer violent shocks that
could damage the camera.

Troubleshooting
Power and Battery
Problem

Possible cause
The batteries are exhausted.
The batteries are not in the correct orientation.
The battery-chamber cover is not latched.
The camera does
The AC power adapter and DC coupler are
not turn on.
not connected properly.
The camera has been left for an extended
period with no batteries inserted and the
AC power adapter/DC coupler unplugged.
The batteries are cold.
Power
supply

There is dirt on the battery terminals.
The camera is in M mode.

u CONTINUOUS is selected for F AF MODE.
The batteries are exhausted.
The camera turns
The AC power adapter or DC coupler has
off suddenly.
been disconnected.

Troubleshooting

The batteries run
down quickly.
The batteries are new, have been left unused
for an extended period, or have been recharged without first being fully discharged
(rechargeable Ni-MH batteries only).

Solution
Page
Insert fresh or fully-charged spare batteries.
8
Re-insert the batteries in the correct orienta8
tion.
Latch the battery-chamber cover.
9
Make sure that the AC power adapter and DC
—
coupler are properly connected.
After inserting the batteries or connecting the
AC power adapter/DC coupler, wait a few mo- —
ments before turning the camera on.
Warm the batteries by placing them in a pocket
or other warm place and re-insert them in the vi
camera immediately before taking a picture.
Clean the terminals with a soft, dry cloth.
—
Select another shooting mode.
21
Discharge Ni-MH batteries using the P DISCHARGE option and recharge them in a battery charger (sold separately). If the batteries
105
do not hold a charge after repeated discharging and recharging, they have reached the end
of their service life and must be replaced.
Select a different focusing option.
81
Insert fresh or fully-charged spare batteries.
8
Make sure that the AC power adapter and DC
—
coupler are properly connected.

109

Troubleshooting
Menus and Displays
Problem
Possible cause
Solution
Menus and displays are English is not selected for the L a
Select ENGLISH.
not in English.
option in the setup menu.

Page
14, 99

Shooting
Problem

Taking
pictures

Focus

110

No picture is
taken when
the shutter
button is
pressed.
The monitor
goes dark after
shooting.
The camera
does not
focus.

Possible cause
Memory is full.
Memory is not formatted.
There is dirt on the memory card contacts.
The memory card is damaged.
The batteries are exhausted.
The camera has turned off automatically.

Solution
Page
Insert a new memory card or delete pictures. 10, 54
Format the memory card.
102
Clean the contacts with a soft, dry cloth.
—
Insert a new memory card.
10
Insert fresh or fully-charged spare batteries.
8
Turn the camera on.
13

The flash has fired.

The monitor may darken while the flash
charges. Wait for the flash to charge.

The subject is close to the camera.
The subject is far away from the camera.
The subject is not suited to autofocus.

Select macro mode.
Cancel macro mode.
Use focus lock.

36
35
33

Troubleshooting
Solution
Choose a different shooting mode.

Page
21

Remove the obstructions.
Change the composition so that the subject’s 31
face occupies a larger area of the frame.
Ask the subject to hold their head straight.
Hold the camera straight.
17
Shoot in bright light.
—
Recompose the picture or turn face detection
31, 33
off and frame the picture using focus lock.
Choose a different shooting mode.

21, 35

Raise the flash.
Wait for the flash to charge.

36
36

Choose a different shooting mode.

Insert fresh or fully-charged spare batteries.
8
Turn super macro and continuous shooting
35, 40
modes off.
Choose a different shooting mode.
Position the subject in range of the flash.
Hold the camera correctly.
Choose a slower shutter speed.

21
124
17
27, 29

Troubleshooting

Problem
Possible cause
Face detection Intelligent Face Detection is not available in
not available. the current shooting mode.
The subject’s face is obscured by sunglasses, a
hat, long hair, or other objects.
The subject’s face occupies only a small area
Intelligent
No face is
of the frame.
Face
detected.
Detection
The subject’s head is tilted or horizontal.
The camera is tilted.
The subject’s face is poorly lit.
Wrong subject The selected subject is closer to the center of
selected.
the frame than the main subject.
Macro mode is Macro mode is not available in the current
Close-ups
not available. shooting mode.
The flash is lowered.
The flash is charging.
The flash is not available in the current shootThe flash does
ing mode.
not fire.
The batteries are exhausted.
The camera is in super macro or continuous
Flash
shooting mode.
Flash mode
The desired flash mode is not available in the
not available. current shooting mode.
The flash does The subject is not in range of the flash.
not fully light The flash window is obstructed.
the subject.
Fast shutter speed selected.

111

Troubleshooting
Problem
Pictures are
blurred.

Problem
images

Pictures are
mottled.
Vertical lines
appear in
pictures.

Possible cause
The lens is dirty.
The lens is blocked.
s is displayed during shooting and the focus frame is displayed in red.
k is displayed during shooting.
The ambient temperature is high and the subject is poorly lit.

Solution
Clean the lens.
Keep objects away from the lens.

Page
108
17

Check focus before shooting.

116

Use the flash or a tripod.
36–37
This is normal and does not indicate a mal—
function.

The camera has been used continuously at Turn the camera off and wait for it to cool
high temperatures.
down.

—

White or purple vertical lines may appear
when a very bright object is framed in the
display. This is normal and does not indicate a
Smear appears The sun or another bright object was in the
malfunction. Smear is not recorded in photo- 120
in pictures.
frame.
graphs but may appear in movies. If possible,
avoid shooting movies with bright objects in
or close to the frame.
Turn the camera off before connecting the AC
power adapter/DC coupler. Leaving the camPictures are
—
Power was interrupted during shooting.
Recording
era on can result in corrupted files or damage
not recorded.
to the memory card.
Continuous
Only one pic- The self timer is on and an option L and N
shooting
Turn the self-timer off.
38
ture is taken. are selected in continuous shooting mode.
mode

112

Troubleshooting
Playback
Problem
Pictures are
grainy.
Pictures
Playback zoom
unavailable.
No sound in
voice memo
Audio
and movie
playback.
Selected
Deletion pictures not
deleted.
File numberFrame no. ing is unexpectedly reset.

Possible cause
The pictures were taken with a different make or
model of camera.
The picture has been resized or cropped to a
or is from another make or model of camera.
The camera is in silent mode.
Playback volume is too low.
The microphone was obstructed.
The speaker is obstructed.

Solution

Page

—

Turn silent mode off.
18
Adjust playback volume.
104
Hold the camera correctly during recording. 57, 96
Hold the camera correctly during playback. 59, 97

Some of the pictures selected for deletion are Remove protection using the device with
protected.
which it was originally applied.

The battery-chamber cover was opened while Turn the camera off before opening the batthe camera was on.
tery-chamber cover.

Troubleshooting

113

Troubleshooting
Connections
Problem
Possible cause
Monitor is off. The camera is connected to a TV.
The camera is not properly connected.
An A/V cable was connected during movie
playback.
No picture or
Input on the television is set to “TV”.
TV
sound.
The camera is not set to the correct video standard.
The volume on the television is too low.
The camera is not set to the correct video stanNo color.
dard.
The computer does not
Computer
The camera is not properly connected.
recognize the
camera.
The camera is not properly connected.
Pictures can
not be printed. The printer is off.
Only one copy
PictBridge
is printed.
The printer is not PictBridge-compatible.
The date is not
printed.

114

Solution
View pictures on the TV.
Connect the camera correctly.
Connect the camera once movie playback
has ended.
Set input to “VIDEO”.
Match the camera Q VIDEO SYSTEM setting to the TV.
Adjust the volume.
Match the camera Q VIDEO SYSTEM setting to the TV.

Page
60
60
59, 60
—
100
—
100

Connect the camera correctly.

Connect the camera correctly.
Turn the printer on.

62
—

—

Troubleshooting
Miscellaneous
Problem

Possible cause

Nothing happens
Temporary camera malfunction.
when the shutter button is pressed.
The batteries are exhausted.
The camera does not
Temporary camera malfunction.
function as expected.

I want to use an AC
power adapter and DC Check the label on the AC power adapter.
coupler overseas.

Solution
Page
Remove and reinsert the batteries or disconnect and reconnect the AC power adapter/ 8
DC coupler.
Insert fresh or fully-charged spare batteries.
8
Remove and reinsert the batteries or disconnect and reconnect the AC power adapter/
8
DC coupler. If the problem persists, contact
your FUJIFILM dealer.
The AC power adapter can be used with voltages of 100–240 V and power frequency of
50/60Hz. However, power outlets differ de- —
pending on the regions. Consult your travel
agent for information on plug adapters.

Troubleshooting

115

Warning Messages and Displays
The following warnings are displayed in the monitor:
Warning
B (red)
A (blinks red)
k
s

(displayed in red
with red focus
frame)
Aperture or shutter
speed shown in red
BLINK DETECTED
FOCUS ERROR
TURN OFF THE CAMERA
AND TURN ON AGAIN
LENS CONTROL ERROR

CARD NOT INITIALIZED

PROTECTED CARD

116

Description
Batteries are low.
Batteries are exhausted.
Slow shutter speed. Picture may be blurred.

Solution
Insert fresh or fully-charged spare batteries.

The camera can not focus.

• Use focus lock to focus on another subject at the
same distance, then recompose the picture (pg. 33).
• Use macro mode to focus when taking close-ups.

Use the flash or mount the camera on a tripod.

The subject is too bright or too dark. The picIf the subject is dark, use the flash.
ture will be over- or under-exposed.
A subject or subjects may have blinked.
Retake the photograph if desired.
Camera malfunction.

Turn the camera off and then on again, taking care not
to touch the lens. If the message persists, contact a
FUJIFILM dealer.

The memory card is not formatted or the
Format the memory card using the K FORMAT opmemory card was formatted in a computer or
tion in the camera setup menu (pg. 102).
other device.
Clean the contacts with a soft, dry cloth. If the message
The memory card contacts require cleaning. is repeated, format the memory card (pg. 102). If the
message persists, replace the memory card.
Camera malfunction.
Contact a FUJIFILM dealer.
The memory card is locked.
Unlock the memory card (pg. 10).

Warning Messages and Displays
Warning
BUSY

CARD ERROR

b MEMORY FULL

WRITE ERROR

FRAME NO. FULL

Troubleshooting

READ ERROR

Description
Solution
The memory card is incorrectly formatted.
Use the camera to format the memory card (pg. 102).
The memory card is not formatted for use in
Format the memory card (pg. 102).
the camera.
Clean the contacts with a soft, dry cloth. If the message
The memory card contacts require cleaning or
is repeated, format the memory card (pg. 102). If the
the memory card is damaged.
message persists, replace the memory card.
Incompatible memory card.
Use a compatible memory card.
Camera malfunction.
Contact a FUJIFILM dealer.
The memory card is full; pictures can not be Delete pictures or insert a memory card with more free
recorded.
space.
Re-insert the memory card or turn the camera off
Memory card error or connection error.
and then on again. If the message persists, contact a
FUJIFILM dealer.
Not enough memory remaining to record ad- Delete pictures or insert a memory card with more free
ditional pictures.
space.
The memory card is not formatted.
Format the memory card (pg. 102).
The file is corrupt or was not created with the
The file can not be played back.
camera.
Clean the contacts with a soft, dry cloth. If the message
The memory card contacts require cleaning. is repeated, format the memory card (pg. 102). If the
message persists, replace the memory card.
Camera malfunction.
Contact a FUJIFILM dealer.
Format the memory card and select RENEW for the
B FRAME NO. option in the X SET-UP menu. Take
The camera has run out of frame numbers (cura picture to reset frame numbering to 100-0001, then
rent frame number is 999-9999).
return to the B FRAME NO. menu and select CONTINUOUS.

117

Warning Messages and Displays
Warning
TOO MANY FRAMES
PROTECTED FRAME
u ERROR
a CAN NOT CROP

CAN NOT CROP
a CANNOT EXECUTE
b CANNOT EXECUTE

DPOF FILE ERROR
CAN NOT SET DPOF
F CAN NOT SET DPOF

CAN NOT ROTATE
F CAN NOT ROTATE

Description
An attempt was made to search more than
5,000 images.
An attempt was made to add a voice memo to
or delete a protected picture.
Voice memo file is corrupt.
Camera malfunction.
An attempt was made to crop a a picture.
The picture selected for cropping is damaged
or was not created with the camera.
An attempt was made to resize a a picture.
An attempt was made to resize a b picture.
The DPOF print order on the current memory
card contains more than 999 images.
The picture can not be printed using DPOF.
Movies can not be printed using DPOF.
The picture is protected.
Movies can not be rotated.

Solution
The maximum number of images on which searches
can be performed is 5,000.
Remove protection before adding voice memos to or
deleting pictures.
The voice memo can not be played back.
Contact a FUJIFILM dealer.
These pictures can not be cropped.
a and b images can not be resized.

The maximum number of images to which DPOF print
order can be tagged is 999 per memory card.
—
—
Remove protection before rotating pictures.
—

PRESS AND HOLD
An attempt was made to adjust the volume
THE DISP BUTTON TO
Exit silent mode before adjusting the volume.
with the camera in silent mode.
DEACTIVATE SILENT MODE
A connection error occurred while pictures
Confirm that the device is turned on and that the USB
COMMUNICATION ERROR were being printed or copied to a computer or
cable is connected.
other device.
Check printer (see printer manual for details). To resume
PRINTER ERROR
Printer out of paper or ink, or other printer er- printing, turn the printer off and then turn it back on.
ror.
PRINTER ERROR
Check printer (see printer manual for details). If printing
RESUME?
does not resume automatically, press MENU/OK to resume.

118

Warning Messages and Displays
Warning

CAN NOT BE PRINTED

Description

Solution
Movies and some pictures created with other devices
An attempt was made to print a movie, a pic- can not be printed. If the picture was created with the
ture not created with the camera, or a picture camera, check the printer manual to confirm that the
in a format not supported by the printer.
printer supports the JFIF-JPEG or Exif-JPEG format. If it
does not, the pictures can not be printed.

Troubleshooting

119

Glossary
Digital zoom: Unlike optical zoom, digital zoom does not increase the amount of visible detail. Instead, details visible using optical zoom are simply enlarged, producing a slightly “grainy” image.
DPOF (Digital Print Order Format): A standard that allows pictures to be printed from “print orders” stored
on a memory card. The information in the order includes the pictures to be printed and the number of
copies of each picture.
EV (Exposure Value): The exposure value is determined by the sensitivity of the image sensor and the amount
of light that enters the camera while the image sensor is exposed. Each time the amount of light doubles, EV
increases by one; each time the amount of light is halved, EV decreases by one. The amount of light entering the
camera can be controlled by adjusting aperture and shutter speed.
HDMI (High-Definition Multimedia Interface): An interface standard for the transmission of images and sound that
adds audio input to the DVI interface used to connect computers to displays.
Motion JPEG: An AVI (Audio Video Interleave) format that stores sound and JPEG images in a single file. Motion JPEG
files can be played in Windows Media Player (requires DirectX 8.0 or later) or QuickTime 3.0 or later.
Smear: A phenomenon specific to CCDs which causes white streaks to appear when very bright light sources, such
as the sun or reflected sunlight, appear in the frame.
White balance: The human brain automatically adapts to changes in the color of light, with the result that objects
that appear white under one light source still appear white when the color of the light source changes. Digital
cameras can mimic this adjustment by processing images according to the color of the light source. This process
is known as “white balance.”
Appendix

120

Memory Card Capacity
The following table shows the recording time or number of pictures available at different image sizes.
All figures are approximate; file size varies with the scene recorded, producing wide variations in the
number of files that can be stored. The number of exposures or length remaining may not diminish
at an even rate.
4 GB

Medium
O

Photographs
Movies 1

O4:3
O3:2
O 16 : 9
P4:3
P3:2
P 16 : 9
Q4:3
Q3:2
Q 16 : 9
h 1280 2
f
g

FINE
570
630
750
1070
1200
1420
2330
2600
3400

8 GB
NORMAL
1120
1250
1470
2080
2330
2720
4340
4820
6160

17 min.
53 min.
112 min.

FINE
1170
1310
1550
2220
2490
2930
4800
5370
7020

NORMAL
2310
2580
3040
4300
4840
5610
8960
9940
12700
35 min.
107 min.
226 min.

1 Individual movies cannot exceed 2 GB in size or 29 minutes in length, regardless of capacity of memory card.
Recording times shown here are the approximate total time of all recorded movies.
2 Use a y card or better when shooting HD movies.

Appendix

121

Specifications
System
Model
Effective pixels
CCD
Storage media
File system

Digital Camera FinePix S4000/S4000A/S3900 series, S3400/S3300/S3200 series
14 million
1/
2.3 -in., square-pixel CCD with primary color filter
SD/SDHC memory cards (see page 10)
Compliant with Design Rule for Camera File System (DCF), Exif 2.3, and Digital Print Order Format
(DPOF)
File format
• Still pictures: Exif 2.3 JPEG (compressed)
• Movies: AVI-format Motion JPEG
• Audio: monaural WAV
Image size (pixels, file size) • O 4 : 3: 4,288 × 3,216 (14 M)
• O 3 : 2: 4,288 × 2,864 (12 M)
• O 16 : 9: 4,288 × 2,416 (10 M)
• P 4 : 3: 3,072 × 2,304 (7 M)
• P 3 : 2: 3,072 × 2,048 (6 M)
• P 16 : 9: 3,072 × 1,728 (5 M)
• Q 4 : 3: 2,048 × 1,536 (3 M)
• Q 3 : 2: 2,048 × 1,360 (3 M)
• Q 16 : 9: 1,920 × 1,080 (2 M)
Lens
S4000/S4000A/S3900 series
Focal length
Fujinon 30 × optical zoom lens, F/3.1 (wide angle)–5.9 (telephoto)
f=4.3 mm–129.0 mm (35-mm format equivalent: 24 mm– 720 mm)
S3400 series
Fujinon 28 × optical zoom lens, F/3.1 (wide angle)–5.9 (telephoto)
f=4.3 mm–120.4 mm (35-mm format equivalent: 24 mm– 672 mm)
S3300 series
Fujinon 26 × optical zoom lens, F/3.1 (wide angle)–5.9 (telephoto)
f=4.3 mm–111.8 mm (35-mm format equivalent: 24 mm– 624 mm)
S3200 series
Fujinon 24 × optical zoom lens, F/3.1 (wide angle)–5.9 (telephoto)
f=4.3 mm–103.2 mm (35-mm format equivalent: 24 mm–576 mm)
Digital zoom
• Still pictures: approx. 6.7 × (S4000/S4000A/S3900 series: up to 201 × / S3400 series: up to 187.6 × /
S3300 series: up to 174.2 × / S3200 series: up to 160.8, with optical zoom)
• Movies: approx. 3 × (h 1280)/approx. 2 × (f, g)
Aperture
F3.1/F8* (wide angle), F5.9/F8/F20* (telephoto), *uses Neutral Density (ND) filter

122

Specifications

Appendix

System
Focus range (distance from Approx. 0.4 m (1.3 ft.)–infinity (wide angle); S4000/S4000A/S3900/S3400 series: approx. 2.8 m (9.2 ft.)–infinity
front of lens)
(telephoto) / S3300/S3200 series: approx. 2.5 m (8.2 ft.)–infinity (telephoto)
• Macro: approx. 7 cm–3 m/2.8 in.–9.8 ft. (wide angle); S4000/S4000A/S3900/S3400 series: approx.
2 m–3 m/6.6 ft.–9.8 ft. (telephoto) /S3300/S3200 series: approx. 1.9 m–3 m/6.2 ft.–9.8 ft. (telephoto)
• Super macro: approx. 2 cm–100 cm/0.8 in.–3.3 ft. (wide angle)
Sensitivity
Standard output sensitivity equivalent to ISO 64, 100, 200, 400, 800, 1600, 3200, 6400 (3200 and 6400
available only at image sizes Q); AUTO, AUTO (400), AUTO (800)
Metering
256-segment through-the-lens (TTL) metering; MULTI, SPOT, AVERAGE
Exposure control
Programmed AE, shutter-priority AE, aperture-priority AE, and manual exposure
Exposure compensation
–2 EV – +2 EV in increments of 1/3 EV (P, S, and A modes)
Scene modes
B (ZOOM BRACKETING), C (NATURAL & N), D (NATURAL LIGHT), C (PORTRAIT),
D (BABY MODE), K (SMILE&SHOOT), M (LANDSCAPE), N (SPORT), O (NIGHT),
H (NIGHT (TRIPOD)), P (FIREWORKS), Q (SUNSET), R (SNOW), S (BEACH), U (PARTY),
V (FLOWER), W (TEXT)
Scene recognition
Available (camera automatically selects b, c, d, e, f, or g)
Picture stabilization
Optical stabilization, CCD shift
Blink detection
Available
Shutter speed (combined • P, S, A, M: 8 s – 1/2,000 s
• O: 1/8 s – 1/2,000 s
• H: 3 s – 1/1,500 s
mechanical and electronic • P: 8 s – 1/2 s
• Other modes: 1/4 s – 1/2,000 s
shutter)
Continuous
• I: up to 1.2 fps; max. 6 frames
• O: up to 1.2 fps; max. 3 frames
• N: up to 1.2 fps; maximum number of frames varies with image size and available memory
• L: up to 1.2 fps; last 6 frames recorded
• K: up to 3.3 fps; max. 20 frames; size P
• J: up to 8 fps; max. 40 frames; size Q
Bracketing
±1/3 EV, ±2/3 EV, ±1 EV
Focus
• Mode: CENTER/MULTI/AREA/CONTINUOUS/TRACKING
• Autofocus system: Contrast-detect TTL AF

123

Specifications
System
White balance

Automatic scene detection; six manual preset modes for direct sunlight, shade, daylight fluorescent,
warm white fluorescent, cool white fluorescent, and incandescent lighting; custom white balance
Self-timer
Off, 2 sec, 10 sec
Flash
Manual pop-up flash with CCD-metered auto flash control (using monitor pre-flashes); effective range when
sensitivity is set to ISO800 is approx. 40 cm–7 m/1.3 ft.–23 ft. (wide angle) or 2.5 m–3.6 m/8.2 ft.–11.8 ft. (telephoto); effective range in macro mode is approx. 30 cm–3 m/1 ft.–9.8 ft. (wide angle) or 2 m–3 m/6.6 ft.–
9.8 ft. (telephoto)
Flash modes
Auto, forced flash, off, slow synchro (red-eye removal off); auto with red-eye removal, forced flash
with red-eye removal, off, slow sync with red-eye removal (red-eye removal on)
Electronic viewfinder (EVF) 0.2-in., 200k-dot color LCD viewfinder
Frame coverage
Approx. 97% (shooting), 100% (playback)
Monitor
S4000/S3400 series
Frame coverage
3.0-in., 460k-dot color LCD monitor
Approx. 97% (shooting), 100% (playback)
S4000A/S3900/S3300/S3200 series
3.0-in., 230k-dot color LCD monitor
Approx. 97% (shooting), 100% (playback)
Movies
h 1280 (1,280 × 720/720p)/f (640 × 480/VGA)/g (320 × 240/QVGA); monaural sound; frame rate 30 fps

124

Specifications
Input/output terminals
A/V OUT (audio/video output)
HDMI output
Digital input/output
Power supply/other
Power sources

Battery life (approximate
number of frames that can
be taken with fresh or fully
charged batteries)

NTSC or PAL output with monaural sound
HDMI Mini Connector
USB 2.0 High Speed; shares A/V OUT connector
•
•
•
•

AA alkaline batteries (×4)
AA lithium batteries (×4; available from third-party suppliers)
AA rechargeable nickel-metal hydride (Ni-MH) batteries (×4; available from third-party suppliers)
AC-5VX AC power adapter and CP-04 DC coupler (sold separately)
Battery type
Approximate number of frames
Alkaline (type supplied with camera)
300
Lithium
700
Ni-MH
500

CIPA standard, measured in B (auto) mode using batteries supplied with camera (alkaline batteries
only) and SD memory card.

Camera dimensions
Camera weight

Appendix

Note: Number of shots that can be taken with battery varies with battery charge level and will decline
at low temperatures.
118 mm × 80.9 mm × 99.8 mm/4.6 in. × 3.2 in. × 3.9 in. (W × H × D), excluding projections
S4000/S4000A/S3900 series
Approx. 445 g/15.7 oz., excluding batteries, accessories, and memory cards
S3400 series
Approx. 445 g/15.7 oz., excluding batteries, accessories, and memory cards
S3300 series
Approx. 445 g/15.7 oz., excluding batteries, accessories, and memory cards
S3200 series
Approx. 445 g/15.7 oz., excluding batteries, accessories, and memory cards

125

Specifications
Power supply/other
Shooting weight

Operating conditions

126

S4000/S4000A/S3900 series
Approx. 540 g/19.0 oz., including batteries and memory card
S3400 series
Approx. 540 g/19.0 oz., including batteries and memory card
S3300 series
Approx. 540 g/19.0 oz., including batteries and memory card
S3200 series
Approx. 540 g/19.0 oz., including batteries and memory card
• Temperature: 0 °C – +40 °C/+32 °F – +104 °F
• Humidity: 10% – 80% (no condensation)

Specifications
Color Television Systems
NTSC (National Television System Committee) is a color television telecasting specification adopted mainly in
the U.S.A., Canada, and Japan. PAL (Phase Alternation by Line) is a color television system adopted mainly in
European countries and China.
Notices
• Specifications subject to change without notice. FUJIFILM shall not be held liable for damages resulting from
errors in this manual.
• Although the monitor is manufactured using advanced high-precision technology, small bright points and
anomalous colors (particularly in the vicinity of text) may appear. This is normal for this type of monitor and
does not indicate a malfunction; images recorded with the camera are unaffected.
• Digital cameras may malfunction when exposed to strong radio interference (e.g., electric fields, static electricity, or line noise).
• Due to the type of lens used, some distortion may occur at the periphery of images. This is normal.

Appendix

127

7-3, AKASAKA 9-CHOME, MINATO-KU, TOKYO 107-0052, JAPAN

http://www.fujifilm.com/products/digital_cameras/index.html

Restrictions on Camera Settings
Shooting Mode and Camera Settings
The options available in each shooting mode are listed below.
Shooting mode
SP
BMB C D C d K M N O H P Q R S U V WN P

Option
F Macro mode

JOFF
N

Flash 2
JON

F
G
OFF
A
N
O
P3
K
L
M
P3

✔
✔
✔
✔
✔

✔
✔

d Exposure compensation 4
OFF
✔
g

Face Detection
ON
B RED EYE REMOVAL
OFF
I

Continuous
shooting

I
L
N
K6
J5
O

c Instant zoom 7

✔ ✔1
✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔

✔

✔ ✔ ✔
✔1 ✔1
✔
✔
✔ ✔ ✔ ✔ ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1
✔1
✔
✔
✔
✔
✔ ✔ ✔1
✔ ✔1
✔
✔
✔
✔1 ✔ ✔
✔1
✔
✔
✔1 ✔1
✔1
✔1
✔1
✔1
✔1
✔1
✔
✔
✔
✔ ✔ ✔1
✔ ✔1
✔
✔
✔1 ✔ ✔
✔
✔
✔1 ✔1
✔ ✔
✔ ✔
✔ ✔
✔ ✔1
✔

✔ ✔ ✔
✔ ✔ ✔
✔
✔ ✔ ✔
✔ ✔ ✔
✔ ✔ ✔
✔ ✔ ✔
✔ ✔ ✔
✔ ✔ ✔

✔

✔ ✔ ✔ ✔

✔

✔1
✔
✔
✔
✔
✔
✔
✔

✔
✔
✔
✔
✔
✔

✔
✔
✔
✔
✔
✔
✔
✔
✔

✔1 ✔
✔
✔
✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔ ✔

✔
✔
✔
✔
✔
✔
✔
✔
✔

A
✔
✔
✔

M F
✔
✔
✔

✔1 ✔ ✔1
✔

✔
✔ ✔1 ✔ ✔1
✔
✔

✔
✔1 ✔1 ✔1 ✔
✔
✔
✔ ✔ ✔1 ✔
✔ ✔
✔
✔ ✔
✔
✔ ✔
✔
✔ ✔
✔
✔ ✔
✔
✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔

✔1 ✔1 ✔
✔
✔
✔ ✔ ✔
✔ ✔ ✔
✔ ✔ ✔
✔ ✔ ✔
✔ ✔ ✔
✔ ✔ ✔

S
✔
✔
✔

✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔

✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔

Restrictions on Camera Settings
Shooting mode
SP
BMB C D C d K M N O H P Q R S U V WN P

Option
J SELF-TIMER
✔
AUTO
✔1
AUTO (800)
AUTO (400)
6400 5
3200 5
N ISO
1600
800
400
200
100
64
O
✔
P
O IMAGE SIZE
✔
Q
✔
O QUALITY
T IMAGE

QUALITY
P

FINEPIX COLOR

✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔
✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔
✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔
✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔9 ✔

S A M F
✔ ✔ ✔
✔
✔

✔
✔
✔
✔
✔
✔
✔
✔
✔ ✔
✔ ✔
✔ ✔

✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔

✔
✔
✔
✔
✔
✔
✔
✔
✔
✔

✔
✔
✔
✔
✔
✔
✔
✔ ✔
✔
✔

h 1280
f
g

FINE
NORMAL
STD
a
b

✔
✔
✔
✔
✔

✔
✔
✔
✔

✔
✔
✔
✔
✔

✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔1
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔

C PHOTOMETRY 8
D WHITE BALANCE
F AF MODE
H SHARPNESS

S FACE RECOGNITION

✔
✔

✔

✔ ✔ ✔ ✔

✔ ✔

✔ ✔ ✔ ✔

✔
✔
✔
✔
✔
✔
✔
✔
✔
✔

✔
✔
✔

Restrictions on Camera Settings
Shooting mode
Option

SP
BMB C D C d K M N O H P Q R S U V WN P

I FLASH
J AE BKT EV STEPS
K CUSTOM SET
X SET-UP
l
L DUAL IS
m

MODE

OFF
ON
NATOR
OFF
ON
D DIGITAL
ZOOM
OFF
30fps
E EVF/LCD
MODE
60fps
G OPERATION VOL.
H SHUTTER VOLUME
I PLAYBACK VOLUME

C AF ILLUMI-

1
2
3
4
5
6
7
8
9

✔ ✔ ✔
✔ ✔ ✔
✔ ✔ ✔
✔ ✔ ✔
✔ ✔ ✔
✔ ✔ ✔
✔
✔ ✔1 ✔1
✔ ✔ ✔
✔ ✔ ✔

✔
✔
✔
✔
✔
✔
✔
✔
✔
✔

✔

✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔

✔

✔
✔
✔
✔
✔
✔
✔
✔
✔
✔

✔
✔
✔
✔

✔1
✔
✔
✔
✔

✔1
✔
✔
✔1

✔
✔
✔
✔
✔
✔
✔
✔
✔
✔

✔
✔
✔
✔

✔1
✔
✔
✔
✔

✔
✔
✔
✔
✔
✔
✔
✔
✔
✔

✔
✔
✔
✔

✔1
✔
✔
✔
✔

Automatically optimized for selected shooting mode.
Flash turns off automatically in super macro mode (G).
Lower flash to select P in modes other than D.
Disabled if flash fires when set to A or K or if flash is set to N or L and subject is poorly lit.
Image sizes over Q are set to Q.
Image sizes over P are set to P.
Tall (portrait-orientation) framing not available at continuous shooting settings of I, N, L, or O.
Fixed at o when Intelligent Face Detection is on.
Aspect ratio fixed at 4 : 3.

✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔
✔ ✔1
✔
✔ ✔1
✔ ✔1
✔
✔

✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔

S
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔

A
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔

M
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔

✔
✔
✔
✔
✔
✔
✔
✔1

✔ ✔ ✔ ✔ ✔

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Create Date                     : 2010:12:25 12:32:29+09:00
Author                          : FUJIFILM Corporation
Title                           : FINEPIX S4000/S4000A/S3900 Series, S3400/S3300/S3200 Series Owner's Manual
Modify Date                     : 2018:01:11 01:00:20Z
Producer                        : 3-Heights(TM) PDF Optimization Shell 4.8.25.2 (http://www.pdf-tools.com)
Page Count                      : 147

EXIF Metadata provided by EXIF.tools

FINEPIX S4000/S4000A/S3900 Series, S3400/S3300/S3200 Series Owner's Manual Fujifilm Fine Pix S3900 User Guide And Product Specification

Navigation menu

Versions of this User Manual:

Views

Navigation