HCD RV777D/RV888D/RV999D HCDRV777D

User Manual: HCDRV777D

Open the PDF directly: View PDF PDF.
Page Count: 120 [warning: Documents this large are best viewed by clicking the View PDF Link!]

1
Ver 1.0 2004. 06
DVD Model Name Using Similar Mechanism NEW
Section DVD Mechanism Type CDM74S-DVBU62
Optical Pick-up Name DBU-3
Tape Deck Model Name Using Similar Machanism HCD-RV660D/RV990D
Section Tape Transport Mechanism Type CWM43RR-35
SERVICE MANUAL
E Model
Australian Model
HCD-RV777D/RV888D/RV999D
Amplifier section
HCD-RV999D
The following measured at AC 120, 127, 220, 230 – 240 V,
50/60 Hz
Continuous RMS power output (reference)
Front speaker: 100 + 100 watts
(6 ohms at 1 kHz, 10%
THD)
Center speaker: 40 watts (6 ohms at 1 kHz,
10% THD)
Surround speaker: 40 + 40 watts
(6 ohms at 1 kHz, 10%
THD)
Sub woofer: 110 watts (4 ohms at
1 kHz, 10% THD)
HCD-RV888D
The following measured at AC 120, 127, 220, 230 – 240 V,
50/60 Hz
Continuous RMS power output (reference)
Front speaker: 100 + 100 watts
(6 ohms at 1 kHz, 10%
THD)
Center speaker: 40 watts (6 ohms at 1 kHz,
10% THD)
Surround speaker: 40 + 40 watts
(6 ohms at 1 kHz, 10%
THD)
HCD-RV777D
The following measured at AC 120, 127, 220, 230 – 240 V,
50/60 Hz
Continuous RMS power output (reference)
100 + 100 watts
(6 ohms at 1 kHz, 10%
THD)
SPECIFICATIONS
Inputs
VIDEO/SAT IN (audio) (phono jacks):
voltage 450/250 mV,
impedance 47 kilohms
GAME INPUT VIDEO (phono jack):
1 Vp-p, 75 ohms
GAME INPUT AUDIO (phono jacks):
voltage 250 mV,
impedance 47 kilohms
MIC (phone jack): sensitivity 1 mV,
impedance 10 kilohms
Outputs
VIDEO/SAT OUT (audio) (phono jacks):
voltage 250 mV,
impedance 1 kilohm
VIDEO OUT (phono jack):
max. output level
1 Vp-p, unbalanced, Sync
negative, load impedance
75 ohms
S-VIDEO OUT (4-pin/mini-DIN jack):
Y: 1 Vp-p, unbalanced,
Sync negative,
C: 0.286 Vp-p, load
impedance 75 ohms
COMPONENT VIDEO OUT:
Y: 1 Vp-p, 75 ohms
PB, PR: 0.7 Vp-p, 75 ohms
Sony Corporation
Home Audio Company
Published by Sony Engineering Corporation
9-877-866-01
2004F04-1
© 2004. 06
– Continued on next page –
DVD DECK RECEIVER
(Photo: HCD-RV888D)
•HCD-RV777D/RV888D/RV999D are
the tuner, deck, DVD and amplifier
section in MHC-RV777D/RV888D/
RV999D.
2
HCD-RV777D/RV888D/RV999D
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
DIGITAL OUT (Square optical connector jack, rear
panel) (HCD-RV777D only)
Wavelength 660 nm
PHONES (stereo mini jack):
accepts headphones of
8 ohms or more
FRONT SPEAKER: Use only the supplied
speaker SS-RV999.
SURROUND SPEAKER (except for MHC-RV777D):
Use only the supplied
speaker SS-RS999 for
MHC-RV999D, SS-
RS391 for MHC-RV888D.
CENTER SPEAKER (except for MHC-RV777D):
Use only the supplied
speaker SS-CT391.
SUB WOOFER OUT: Use only the supplied
speaker SA-RV999D for
MHC-RV999D.
voltage 1 V,
impedance 1 kilohm
Disc player section
System Compact disc and digital
audio and video system
Laser Semiconductor laser
(DVD: λ=650 nm,
CD: λ=780 nm)
Emission duration:
continuous
Frequency response DVD (PCM 48 kHz):
2 Hz – 22 kHz (±1 dB)
CD: 2 Hz – 20 kHz (±1 dB)
Video color system format
Latin American model:
NTSC
Other models: NTSC, PAL
Tape deck section
Recording system 4-track 2-channel stereo
Frequency response 40 – 13,000 Hz (±3 dB),
using Sony TYPE I
cassette
Tuner section
FM stereo, FM/AM superheterodyne tuner
FM tuner section
Tuning range 87.5 – 108.0 MHz
(50-kHz step)
Antenna FM lead antenna
Antenna terminals 75 ohm unbalanced
Intermediate frequency 10.7 MHz
AM tuner section
Tuning range
Latin American models: 530 – 1,710 kHz (with the
interval set at 10 kHz)
531 – 1,602 kHz (with the
interval set at 9 kHz)
Saudi Arabian model: 531 – 1,602 kHz (with the
interval set at 9 kHz)
Other models: 531 – 1,602 kHz (with the
interval set at 9 kHz)
530 – 1,710 kHz (with the
interval set at 10 kHz)
Antenna AM loop antenna
Antenna terminals External antenna terminal
Intermediate frequency 450 kHz
General
Power requirements
Australian model: 230 – 240 V AC, 50/60 Hz
Saudi Arabian model: 120 – 127 V, 220 V or
230 – 240 V AC,
50/60 Hz
Adjustable with voltage
selector
Mexican model: 127 V AC, 60 Hz
Thai model: 220 V AC, 50/60 Hz
Other models: 120 V, 220 V or 230 –
240 V AC, 50/60 Hz
Adjustable with voltage
selector
Power consumption
MHC-RV999D/RV888D 300 watts
MHC-RV777D 230 watts
Dimensions (w/h/d) Approx. 280 × 327 × 385 mm
Mass
HCD-RV999D/RV888D Approx. 12.5 kg
HCD-RV777D Approx. 11.0 kg
Supplied accessories: Remote Commander (1)
R6 (size AA) batteries (2)
AM loop antenna (1)
FM lead antenna (1)
Video cable (1)
Audio cord
(MHC-RV999D only) (1)
Speaker pads
MHC-RV999D (22)
MHC-RV888D (10)
MHC-RV777D (8)
Surround speaker cable
(MHC-RV888D only) (2)
Design and specifications are subject to change without
notice.
3
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
HCD-RV777D/RV888D/RV999D
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
Notes on Chip Component Replacement
•Never reuse a disconnected chip component.
•Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing
•Keep the temperature of soldering iron around 270°C during
repairing.
•Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
•Be careful not to apply force on the conductor when soldering
or unsoldering.
SETTING AND RELEASING THE CD DISC TRAY LOCK
FUNCTION
This set has a disc tray lock function to prevent discs for
demonstration at shops from theft. While this lock function is set,
the tray will not be delivered out even when the OPEN/CLOSE
button is pressed.
Setting method:
Press the OPEN/CLOSE button while pressing the STOP button.
After a few seconds, the message “LOCKED” will appear on the
fluorescent indicator tube with the tray locked.
Releasing method:
Just as the lock is set, press the OPEN/CLOSE button while
pressing the STOP button.
After a few seconds, the message “UNLOCKED” will appear with
the lock released.
LASER DIODE AND FOCUS SEARCH OPERATION
CHECK
Carry out the “S curve check” in “DVD section adjustment” and
check that the S curve waveforms is output three times.
NOTE OF REPLACING THE DMB07 BOARD
When replacing the DMB07 board, since the adjustment value is
not set up correctly, “Drive Auto Adjustment” can’t be performed.
In this case, initialize Memory in the following procedures.
Procedure:
1. Set the test mode. (See page 22)
2. Press the [2] key of the remote commander, and set the “DRIVE
MANUAL OPERATION”. (See page 27)
3. Press the [6] key of the remote commander, and set the “2-6,
Memory Check”. (See page 29)
4. Press the [CLEAR] key of the remote commander, and initialize
Memory.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
•Unleaded solder melts at a temperature about 40 °C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to about
350 °C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
•Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
•Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may also
be added to ordinary solder.
This appliance is
claassified as a CLASS 1
LASER product. This
label is located on the
rear exterior.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
Laser component in this product is capable
of emitting radiation exceeding the limit for
Class 1.
4
HCD-RV777D/RV888D/RV999D
MODEL IDENTIFICATION
– BACK PANEL –
MODEL PARTS No.
RV999D: E3, E15 4-254-657-0s
RV999D: EA 4-254-657-1s
RV999D: MY, SP 4-254-657-2s
RV999D: AUS 4-254-657-3s
RV999D: PH 4-254-657-5s
RV999D: MX 4-254-657-6s
RV999D: E51 4-254-657-7s
RV999D: AR 4-254-657-9s
RV888D: E3, E15 4-254-658-0s
RV888D: EA 4-254-658-1s
RV888D: MY, SP 4-254-658-2s
RV888D: AUS 4-254-658-3s
RV777D: E3, E15 4-254-659-0s
RV777D: EA 4-254-659-1s
RV777D: MY, SP 4-254-659-2s
RV777D: PH 4-254-659-4s
•Abbreviation
E3 : 240 V AC area in E model
E15 : Iran model
E51 : 220 V AC area in E model
AUS : Australian model
AR : Argentina model
EA : Saudi Arabia model
PH : Philippine model
SP : Singapore model
MY : Malaysia model
MX : Mexican model
PARTS No.
5
TABLE OF CONTENTS
1. SERVICE NOTE
1-1. Service Position of CDM .................................................... 6
1-2. Service Position of DMB07 Board, Video Board ............... 7
1-3. Service Position of TCM ..................................................... 8
1-4. Service Position of Front Amp Board ................................. 8
1-5. Note of Transformer ............................................................ 9
1-6. Decision to Pass or Fail of the Optical Pick-Up Block ....... 9
2. GENERAL
Main Unit .............................................................................. 10
Remote Control ..................................................................... 11
3. DISASSEMBLY
3-1. Case ................................................................................... 13
3-2. CD Door ............................................................................ 13
3-3. Front Panel Section, DVD Block Section ......................... 14
3-4. Tape Mechanism Deck ...................................................... 15
3-5. Panel Board ....................................................................... 15
3-6. Jack Board ......................................................................... 16
3-7. Back Panel Section............................................................ 16
3-8. Main Board (HCD-RV888D/RV999D) ............................. 17
3-9. Main Board (HCD-RV777D) ............................................ 17
3-10. Surround Amp Board, Front Amp Board
(HCD-RV888D/RV999D) ................................................. 18
3-11. DVD Mechanism Block, DMB07 Board, Video Board .... 18
3-12. RF Board, Pick-Up Unit.................................................... 19
3-13. SW Board, Driver Board ................................................... 19
3-14. Sensor Board ..................................................................... 20
3-15. Motor (TB) Board ............................................................. 20
3-16. Motor (LD) Board ............................................................. 21
4. TEST MODE ..................................................................... 22
5. MECHANICAL ADJUSTMENTS ............................... 33
6. ELECTRICAL ADJUSTMENTS................................. 34
7. DIAGRAMS
7-1. IC Pin Descriptions ........................................................... 36
7-2. Block Diagram –DVD DSP Section– ............................... 47
7-3. Block Diagram –DAC Section– ........................................ 48
7-4. Block Diagram –Main Section– ........................................ 49
7-5. Block Diagram –DVD SYS Section– ............................... 50
7-6. Circuit Boards Location .................................................... 51
7-7. Note for Printed Wiring Boards
and Schematic Diagrams .................................................. 51
7-8. Printed Wiring Board
–DVD Mechanism Section (1/2)– ..................................... 52
7-9. Schematic Diagram –DVD Mechanism Section (1/2)– .... 53
7-10. Printed Wiring Boards
–DVD Mechanism Section (2/2)– ..................................... 54
7-11. Schematic Diagram –DVD Mechanism Section (2/2)– .... 55
7-12. Printed Wiring Board –DMB07 Section– ......................... 56
7-13. Schematic Diagram –DMB07 Section (1/8)– ................... 58
7-14. Schematic Diagram –DMB07 Section (2/8)– ................... 59
7-15. Schematic Diagram –DMB07 Section (3/8)– ................... 60
7-16. Schematic Diagram –DMB07 Section (4/8)– ................... 61
7-17. Schematic Diagram –DMB07 Section (5/8)– ................... 62
7-18. Schematic Diagram –DMB07 Section (6/8)– ................... 63
7-19. Schematic Diagram –DMB07 Section (7/8)– ................... 64
7-20. Schematic Diagram –DMB07 Section (8/8)– ................... 65
7-21. Printed Wiring Board –Main Section– .............................. 66
7-22. Schematic Diagram –Main Section (1/3)– ........................ 67
7-23. Schematic Diagram –Main Section (2/3)– ........................ 68
7-24. Schematic Diagram –Main Section (3/3)– ........................ 69
7-25. Printed Wiring Board –Video Section– ............................. 70
7-26. Schematic Diagram –Video Section– ................................ 71
7-27. Printed Wiring Board –Front AMP Section– .................... 72
7-28. Schematic Diagram –Front AMP Section– ....................... 73
7-29. Printed Wiring Boards –Surround AMP Section– ............ 74
7-30. Schematic Diagram –Surround AMP Section– ................. 75
7-31. Printed Wiring Boards –Panel Section– ............................ 76
7-32. Schematic Diagram –Panel Section– ................................ 77
7-33. Printed Wiring Boards –Jack Section– .............................. 78
7-34. Schematic Diagram –Jack Section– .................................. 79
7-35. Printed Wiring Board –Trans Section– ............................. 80
7-36. Schematic Diagram –Trans Section– ................................ 81
7-37. Printed Wiring Board –Sub Trans Section– ...................... 82
7-38. Schematic Diagram –Sub Trans Section– ......................... 83
7-39. IC Block Diagrams............................................................ 84
8. EXPLODED VIEWS
8-1. Main Section ..................................................................... 87
8-2. Front Panel Section (1)...................................................... 88
8-3. Front Panel Section (2)...................................................... 89
8-4. Front Panel Section (3)...................................................... 90
8-5. DVD Block Section ........................................................... 91
8-6. Main Board Section (1/2) .................................................. 92
8-7. Main Board Section (2/2) .................................................. 93
8-8. DVD Mechanism Deck Section (1) .................................. 94
8-9. DVD Mechanism Deck Section (2) .................................. 95
9. ELECTRICAL PARTS LIST ........................................ 96
HCD-RV777D/RV888D/RV999D
6
HCD-RV777D/RV888D/RV999D
1-1. SERVICE POSITION OF CDM
SECTION 1
SERVICE NOTE
J-2501-103-A
stand
RF board
DVD mechanism bloc
k
7
HCD-RV777D/RV888D/RV999D
1-2. SERVICE POSITION OF DMB07 BOARD, VIDEO BOARD
stand
DMB07 board
DMB07 board
Note : Remove the board and
then reassemble the CD block.
J-2501-103-A
DMB07 board
VIDEO board
VIDEO board
VIDEO board
8
HCD-RV777D/RV888D/RV999D
1-4. SERVICE POSITION OF FRONT AMP BOARD
1-3. SERVICE POSITION OF TCM
tape mechanis
m
FRONT AMP board
insulating plate
HP board
Note1: For sounding,
remove the HP board
from the front panel and connect it.
Note2: Connect the ground (3 places)
to the chassis of the main body.
9
HCD-RV777D/RV888D/RV999D
1-6. DECISION TO PASS OR FAIL OF THE OPTICAL PICK-UP BLOCK
1-5. NOTE OF TRANSFORMER
oscilloscop
e
+
DMB07 board
CN901 pin 1 –
CN901 pin 3
CD : 1.05
±
0.2 Vp-p
VOLT/DIV : 200 mV
TIME/DIV : 500 nS
DVD : 1.09
±
0.2 Vp-
RF signal waveform
– DMB07 BOARD (SIDE A) –
CN901
17
Connection:
Procedure:
1. Connect an oscilloscope to test point 1 pin and 3 pin of CN901
on the DMB07 board.
2. Turn the power on.
3. Put the disc (LUV-P01) (Part No.: 4-999-032-01) (CD) in to
playback.
4. Confirm that oscilloscope waveform is clear and check RF
signal level is correct or not.
5. Put the disc (TDV-520CSO) (Part No.: J-2501-236-A) (DVD)
in to playback.
6. Perform Comfirmation in the same manner as step 4.
Note: A clear RF signal waveform means that the shape “◊” can be clearly
distinguished at the center of the waveform.
Checking Location:
transformer
(T901)
more than 3mm
power cord
Pull the power cord in the direction of the arrow
A
with care to keep the cord from
contact with the transformer (T901).
Then fix the cord using two clips
indicated by the arrow
B
.
back panel
australian, saudi arabia
model only
SUB TRANS boar
d
A
B
B
NOTE: Make sure that the power cord is distant
more than 3mm from the transformer (T901).
10
HCD-RV777D/RV888D/RV999D SECTION 2
GENERAL This section is extracted
from instruction manual.
11
HCD-RV777D/RV888D/RV999D
12
HCD-RV777D/RV888D/RV999D SECTION 3
DISASSEMBLY
Note : Disassemble the unit in the order as shown below.
3-1. CASE
(Page 13)
3-2. CD DOOR
(Page 13)
SET
3-12. RF BOARD,
PICK-UP UNIT
(Page 19)
3-14. SENSOR BOARD
(Page 20)
3-15. MOTOR (TB) BOARD
(Page 20)
3-16. MOTOR (LD) BOARD
(Page 21)
3-13. SW BOARD,
DRIVER BOARD
(Page 19)
3-3. FRONT PANEL SECTION,
DVD BLOCK SECTION
(Page 14)
3-7. BACK PANEL SECTION
(Page 16)
3-8. MAIN BOARD (HCD-RV888D/RV999D)
(Page 17)
3-9. MAIN BOARD (HCD-RV777D)
(Page 17)
3-10. SURROUND AMP BOARD,
FRONT AMP BOARD
(HCD-RV888D/RV999D)
(Page 18)
3-11. DVD MECHANISM BLOCK,
DMB07 BOARD,
VIDEO BOARD
(Page 18)
3-5. PANEL BOARD
(Page 15)
3-4. TAPE MECHANISM DECK
(Page 15)
3-6. JACK BOARD
(Page 16)
13
HCD-RV777D/RV888D/RV999D
3-2. CD DOOR
Note : Follow the disassembly procedure in the numerical order given.
3-1. CASE
1
two screws
(case 3 TP2)
2
screw
(case 3 TP2)
4
screw
(case 3 TP2)
3
two screws
(case 3 TP2)
5
four screws (+BVTT 3
×
6)
9
case
6
three screws
(+BVTT 3
×
6)
7
7
8
2
Pull-out the disc tray.
4
door (CD) assy
1
Turn the pulley to the direction of arrow.
pulley
Front panel side
CD mechanism deck (CDM74S-DVBU62)
3
14
HCD-RV777D/RV888D/RV999D
3-3. FRONT PANEL SECTION, DVD BLOCK SECTION
9
CN605
8
CN706
7
CN503
0
connector
qa
connector
2
screw
(+BVTT 3
×
6)
5
screw
(+BVTP 3
×
8)
4
screw
(+BVTP 3
×
8)
3
screw
(+BVTT 3
×
6)
6
two lugs
lug
1
three screws (+BVTT 3
×
6)
qf
three
screws
(+BVTT 3
×
6)
qd
three
screws
(+BVTT 3
×
10)
qs
two
screws
(+BVTT 3
×
10)
qg
qj
CN301
wa
CN902
qh
CN804
qk
CN543
ql
CN543
w;
DVD block section
ws
front panel section
15
HCD-RV777D/RV888D/RV999D
3-4. TAPE MECHANISM DECK
3-5. PANEL BOARD
1
two
screws
(+BVTP 2.6
×
8)
3
two
screws
(+BVTP 2.6
×
8
)
2
three
screws
(+BVTP 2.6
×
8)
4
tape mechanism deck
3
seven
claws
4
CN2
5
CN104
6
PANEL board
1
eight
screws
(+BVTP 2.6
×
8
)
2
two
screws
(+BVTP 2.6
×
8)
16
HCD-RV777D/RV888D/RV999D
3-7. BACK PANEL SECTION
3-6. JACK BOARD
1
two
screws
(+BVTP 2.6
×
8)
4
shield plate
6
JACK board
5
two mic knobs
2
screw
(+BVTP 2.6
×
8)
3
screw
(+BVTP 2.6
×
8)
qs
back panel section
5
four
screws
(+BVTT 3
×
6)
6
screw
(+BVTP 3
×
10)
9
two
screws
(+BVTT 3
×
6)
8
two
screws
(+BVTP 3
×
10)
7
two
screws
(+BVTP 3
×
10
)
qa
CN704
0
1
CN903
2
CN901
3
CN902
4
CN102
17
HCD-RV777D/RV888D/RV999D
3-8. MAIN BOARD (HCD-RV888D/RV999D)
3-9. MAIN BOARD (HCD-RV777D)
8
two
screws
(+BVTP 3
×
6)
qd
MAIN board
6
screw
(+BVTT 3
×
6)
1
screw
(+BVTT 3
×
6)
5
screw
(+BVTT 3
×
6
)
7
screw
(+BVTT 3
×
6)
9
screw
(+BVTT 3
×
6)
0
qs
two claws
SURROUND AMP board
2
CN914
3
CN915
4
CN913
qa
CN901
CN705
CN707
8
two
screws
(+BVTP 3
×
6)
5
screw
(+BVTP 3
×
6
)
qd
MAIN board
6
screw
(+BVTT 3
×
6)
7
screw
(+BVTT 3
×
6)
9
screw
(+BVTT 3
×
6)
0
qs
claw
LEAD PIN board
CN707
CN705
2
CN914
3
CN915
4
CN913
1
screw
(+BVTT 3
×
6)
qa
CN901
18
HCD-RV777D/RV888D/RV999D
3-11. DVD MECHANISM BLOCK, DMB07 BOARD, VIDEO BOARD
3-10. SURROUND AMP BOARD, FRONT AMP BOARD (HCD-RV888D/RV999D)
1
CN302
2
CN372
3
two
screws
(+BVTP 3
×
16)
4
two
screws
(+BVTP 3
×
8
)
5
SURROUND AMP boar
d
6
FRONT AMP board
2
screw
(+BVTP 3
×
8
)
bracket (DVD)
7
two
screws
(+BVTT 3
×
6)
qa
two
screws
(+BVTT 3
×
6)
qs
VIDEO board
9
heat sink
0
DMB07 board
8
two
screws
(+BVTT 3
×
6)
4
3
screw
(+BVTP 3
×
8)
1
CN501
qd
DVD mechanism block
5
CN102
6
CN801
19
HCD-RV777D/RV888D/RV999D
3-12. RF BOARD, PICK-UP UNIT
3-13. SW BOARD, DRIVER BOARD
9
insulator
qa
insulator(RB)
0
insulator
5
RF board
2
two screws
(+BVTT 2.6
×
6)
7
step screw (M)
6
step screw (M)
8
step screw (M)
qs
pick-up unit
holder (DBU) assy
3
CN003
4
CN001
1
floating
screw
(+PTPWH M2.6
)
6
DRIVER boar
d
2
SW board
3
CN704
4
CN703
7
CN702 (flat type)
5
two
screws
(+BTTP (M2.6))
1
screw
(+BTTP (M2.6))
20
HCD-RV777D/RV888D/RV999D
3-15. MOTOR (TB) BOARD
3-14. SENSOR BOARD
2
tray
3
belt (table)
5
pulley (table)
8
screw
(+BTTP (M2.6))
9
SENSOR board
7
gear (geneva)
0
CN731
1
floating
screw
(+PTPWH M2.6)
6
floating
screw
(+PTPWH M2.6)
4
floating
screw
(+PTPWH M2.6)
4
Remove the two solderings of motor.
3
MOTOR (TB) board
5
table motor assy (M741)
2
two
screws
(+BTTP (M2.6))
1
21
HCD-RV777D/RV888D/RV999D
3-16. MOTOR (LD) BOARD
4
Remove the two solderings of motor.
3
MOTOR (LD) board
1
belt (loading)
5
loading motor assy (M751)
2
two
screws
(+BTTP (M2.6))
22
HCD-RV777D/RV888D/RV999D
[GC Test Mode]
•This mode is used to check the fluorescent indicator tube, LEDs,
keyboard, volume and phones.
Procedure:
1. Press three buttons of x , PLAY MODE/TUNING MODE
and ENTER simultaneously.
2. LEDs and fluorescent indicator tube are all turned on.
3. Press two buttons of X and ENTER simultaneously. Whenever
these two buttons are pressed simultaneously, the mode changes
from Key check, Key count check, Headphones input check
and Volume check in this order.
4. When the Key check mode is entered, the message
“KEY :0 0 0” is displayed.
The keys that are assigned to the respective channels of the key
entry signal lines (KEY1, KEY2, KEY3) that are input to IC101
Display Controller on the PANEL board, are checked. While
you press the button, the number that corresponds to the key
shown in the table below, is displayed in the location of the
corresponding channel. (The ?/1 and DISPLAY buttons are
not included in these channels.)
[Cold Reset]
•The cold reset clears all data including preset data stored in the
RAM to initial conditions. Execute this mode when returning
the set to the customer.
Procedure:
1. Press three buttons of x , PLAY MODE/TUNING MODE
and DISC 1 simultaneously.
2. The message “COLD RESET” is displayed, and the set is reset.
[Tuner Step Change]
•A step of AM channels can be changed over between 9 kHz and
10 kHz.
Procedure:
1. Press the `/1 button to turn the power ON, and set the function
to TUNER/BAND “AM”.
2. Press the `/1 button to turn the power OFF.
3. Press two buttons of PLAY MODE/TUNING MODE and
`/1 simultaneously, and the message changes to “AM 9 k
STEP” or “AM 10 k STEP”, and thus the channel step is changed
over.
[VIDEO/MD Function Change]
•Change of function VIDEO or MD (also the input level changes).
Procedure:
1. Press the `/1 button to turn the power ON.
2. Press two buttons of VIDEO/SAT and `/1 simultaneously,
and the message changes to “MD” or “VIDEO”, and thus the
channel step is changed over.
3. Press the `/1 button to turn the power OFF.
[DISC TRAY LOCK]
The disc tray lock function for the antitheft of a demonstration disc
in the store is equipped.
Setting Procedure :
1. Press the ?/1 button to turn the power ON.
2. Press two buttons of x and Z simultaneously for five seconds.
3. The message “LOCKED” is displayed, and the tray is locked.
Releasing Procedure :
1. Press two buttons of x and Z simultaneously for five seconds.
2. The message “UNLOCKED” is displayed, and the tray is
unlocked.
Note: When the message “LOCKED” is displayed, the tray lock is
not released by turning power ON/OFF with the ?/1 button.
SECTION 4
TEST MODE
5. When the Key count check mode is entered, the message
“KEYCN:T 0 1” is displayed.
Whenever the button is pressed, number in the first digit
increments (30). At the same time, only when the key is being
pressed, the KEY channel is displayed in the second digit.
(KEY1: 2, KEY2: 3, KEY3: 4)
(The buttons that are already pressed once and the buttons of
?/1 and DISPLAY are not counted.)
6. When the Headphones input check mode is entered, the message
“H_P OFF” or “H_P ON” is displayed, and depending on the
PHONES jack status.
7. When the Volume check mode is entered, the message
“VOLUME FLAT” or “VOLUME DOWN” or “VOLUME UP”
is displayed, and depending on the VOLUME status.
8. You can exit the Test Mode when you press two buttons of X
and ENTER simultaneously.
Display Left Center Right
(KEY1) (KEY2) (KEY3)
1EQ BAND DVD GROOVE
2DISC 1 TUNER/BAND SOUND FIELD
3DISC 2 TAPE A/B EFFECT
ON/OFF
4DISC 3 GAME TUNING +
5DISC SKIP/ VIDEO/SAT gG
EX-CHANGE
6ZILLUMINATION M
ALBUM +
7KARAOKE/ PLAY MODE/ m
MPX TUNING MODE ALBUM –
8P-FILE GAME X
MIXING
9PRESET EQ CD SYNC x
10 ENTER REC PAUSE/ TUNING –
START
23
HCD-RV777D/RV888D/RV999D
[Aging Mode]
This mode can for operation check of tape deck section.
•If an error occurred:
The aging operation stops and display then status.
•If no error occurs:
The aging operation continues repeatedly.
Procedure:
1. Press the DVD button to select the function “DVD”.
2. Load the tapes into the decks A and B respectively.
3. Set a disc in “DISC 1” tray.
4. Press the PLAY MODE/TUNING MODE button to set the
“ALL DISCS” mode, and press the PRESET EQ button to
“REPEAT” off.
5. Press three buttons of x , PLAY MODE/TUNING MODE
and DISC SKIP/EX-CHANGE simultaneously.
6. The message “AGING” is displayed, and aging mode start.
7. To exit from the aging mode, operate the cold reset.
•The sequence during the aging mode is following as below.
•If an error occurred, stop display that step.
Aging mode sequence (Tape deck section):
[MC Test Mode]
•This mode is used to check operations of the respective sections
of Amplifier, Tuner, and Tape.
Procedure:
•To enter MC Test Mode
1. Press the `/1 button to turn the power ON.
2. Press three buttons of x , PLAY MODE/TUNING MODE
and DISC 3 simultaneously.
*Check of Amplifier
Initial settings: Input , GAME
EQ , FLAT
Mode , MUSIC
VAC S , OFF
Output channel switching:
MUSIC key: L , LR , R through
MOVIE key: L , SL R , SR through
GAME key:L , L, SL, C R , R, SR, SW through
TOOL MODE key: L , CR , SW through
1. When VOLUME control knob is turned clockwise even slightly,
the sound volume increases to is maximum and the message
“VOLUME MAX” is displayed for two seconds, then the display
returns to the original display.
2. When VOLUME control knob is tuned counter-clockwise even
slightly, the sound volume decreases to its minimum and the
message “VOLUME MIN” is displayed for two seconds, then
the display returns to the original display.
3. When you press the PRESET EQ button, the message “GEQ
FLAT” is displayed, and the entire band of the graphic equalizer
is set to the center level.
4. Whenever you press the GROOVE button, it toggles between
“VACS ON” and “VACS OFF” so that you can switch ON or
OFF of VACS.
*To return to normal mode again.
1. When you want to exit this mode, press the `/1 button.
2. The cold reset is enforced at the same time.
Rewind the tape A
“TAPE AAG--1”
Rewind the tape B
“TAPE AAG--2”
FWD play the tape A
“TAPE AAG--3”
Fast forward the tape A
“TAPE AAG--4”
RVS play the tape A
“TAPE AAG--5”
Rewind the tape A
“TAPE AAG--6”
FWD play the tape B
“TAPE BAG--3”
Fast forward the tape B
“TAPE BAG--4”
RVS play the tape B
“TAPE BAG--5”
Rewind the tape B
“TAPE BAG--6”
Shut off
Shut off
2 minutes
Shut off or 20 seconds
2 minutes
Shut off
2 minutes
Shut off or 20 seconds
2 minutes
Shut off
24
HCD-RV777D/RV888D/RV999D
2. CDM Error History <CDM74S Error History Display>
11 digits are displayed after the M character.
Example of display : M0FF400220000
1st digit : Indicates the error history number.
0 is the latest error
2nd to 3rd digits : Indicates the details of the problem.
01 : Initialization table is currently rotating 1
02 : Initialization table is currently rotating 2
03 : Initialization table is currently rotating 3
04 : Currently DISC SKIP in OPEN mode
05 : CLOSE table is currently rotating
06 : Chucking table is currently rotating
07 : Currently performing SHIP operations
08 : Currently performing release operations
09 : Currently performing POWER OFF
operations
4th to 5th digits : Processing when problems occur
01 : Currently performing SHIP operations
02 : Currently performing POWER OFF
operations
03 : Currently initializing
04 : Currently performing release operations
05 : Currently in chuck stop state
06 : Currently performing CLOSE operations
07 : Currently performing exchange CLOSE
operations
08 : Currently performing OPEN operations
09 : Currently performing OPEN POP UP
operations
0A: Currently performing exchange OPEN
operations
6 to 7th digits : Operations currently performed for problems
which have occurred
8th to 9th digits : Targets of processing when problems occur
Same as 4th to 5th digits
10th to 11th digits : Fixed at 00
[DVD and CD Ship Mode (No Memory Clear)]
•This mode moves the position to the position durable to
vibration. Use this mode when returning the set to the customer
after repair.
Procedure:
1. Press the `/1 button to turn the power ON.
2. Press two buttons of DVD and `/1 simultaneously.
3. After the “STANDBY” display blinks 15 times, the message
“LOCK” is displayed, and the DVD ship mode is set.
[DVD and CD Ship Mode (Memory Clear)]
•This mode moves the pickup to the position durable to
vibration. Use this mode when returning the set to the customer
after repair.
Procedure:
1. Press the `/1 button to turn the power ON.
2. Press three buttons of x , DVD and DISPLAY simultaneously.
3. After the “STANDBY” display blinks 15 times, the message
“LOCK” is displayed, and the DVD ship mode is set.
[DVD Service Mode]
•The sequence during the aging mode is following as below.
Aging mode sequence (DVD section):
Disc 1 Chucking
TOC Read
Tray Turn
2 seconds
Track 1 Play
Last Track Play
2 seconds
Error History Display
1. BD Error History Display
11 digits are displayed after the D character.
Example of display : D00209010100
1st digit : Indicates the error history number.
0 is the latest error
2nd to 3rd digits : Indicates details of the problem.
01 : Cannot focus
02 : GFS NG
03 : Start time over
04 : Focus deviates continuously
05 : Q code absent for some time
4th to 5th digits : Processing when problems occur
01 : Currently SHIP processing
02 : Currently POWER OFF processing
03 : Currently initializing
04 : Currently stopping
05 : Currently STOP operation processing
06 : Currently start processing
07 : Currently TOC reading
08 : Currently searching
09 : Currently playing
0A : Currently pausing
0B : Currently PLAY manual searching
0C : Currently PAUSE manual searching
6th to 7th digits : Operations currently performed for problems
which have occurred
8th to 9th digits : Rotation speed of DISC when problems occur
01 : x1 speed
02 : x2 speed
10th to 11th digits : Fixed at 00
25
HCD-RV777D/RV888D/RV999D
[REPEAT 5 LIMIT OFF MODE]
•This mode is used to enable infinite repetitions.
Normally, the number of repetitions allowed is 5.
Procedure:
1. Press the `/1 button to turn the power ON.
2. Set the function “DVD”.
3. Press three buttons of x , DVD and ENTER is
simultaneously.
4. Infinite repetitions is enabled.
5. This state is maintained (memorized) until COLD RESET is
executed.
DVD OSD Test Mode
[GENERAL DESCRIPTION]
The Test Mode allows you to make diagnosis and adjustment easily
using the remote commander and monitor TV. The instructions,
diagnostic results, etc. are given on the on-screen display (OSD).
[TEST DISC LIST]
Use the following test disc on test mode.
LUV-P01 (CD): PART No. 4-999-032-01
TDV-520CSO (DVD-SL): PART No. J-2501-236-A
TDV-540C (DVD-DL): PART No. J-2501-235-A
Note: Do not use exiting test disc for DVD.
[STARTING TEST MODE]
1. Press the `/1 button to turn the power ON, and set the function
to DVD.
2. While pressing two buttons of xand Z simultaneously, and
turn the VOLUME control knob clockwise to enter the test
mode.
3. The message “SERVICE IN” is displayed, and displays the Test
Mode Menu on the monitor screen as follows. (At the bottom
of the menu screen, the model name and revision number are
displayed)
Test Mode Menu
0. Syscon Diagnosis
1. Drive Auto Adjustment
2. Drive Manual Operation
3. Mecha Aging
4. Emergency History
5. Mecha Error History
6. Version Information
7. Video Level Adjustment
Exit: POWER Key
Model :MHC-RVXXXD xx
Revision :x.xx
4. To execute each function, select the desired menu and press its
number on the remote commander RM-SR246D.
5. To release from test mode, press the `/1 button and turn the
power OFF.
[OPERATING TEST MODE]
0. SYSCON DIAGNOSIS
The same contents as board detail check by serial interface can be
checked from the remote commander operation.
On the Test Mode Menu screen, press 10/0 button on the remote
commander, and the following Check Menu will be displayed.
### Syscon Diagnosis ###
Check Menu
0. Quit
1. All
2. Version
3. EEPROM
4. GPIO
5. SD Bus
6. Video
0-0. Quit
Quit the Syscon Diagnosis and return to the Test Mode Menu.
26
HCD-RV777D/RV888D/RV999D
•Example display
### Syscon Diagnosis ###
Diag All Check
No.2 Version
2-3. ROM Check Sum
Check Sum = xxxx
Press NEXT Key to Continue
Press PREV Key to Repeat
For the ROM Check, the check sum calculated by the Syscon is
output, and therefore you must compare it with the specified value
for confirmation.
Following the message, press the > button to go to the next
item, or press the . button to repeat the same operation again.
To quit the diagnosis and return to Check Menu screen, press the
ENTER button on the remote commander to display Check Menu.
•Error occurred
If an error occurred, the diagnosis is suspended and error is displayed.
Press the ENTER button on the remote commander to quit the
diagnosis, or press the . button to repeat the same check where
an error occurred, or press the > button to continue the check
from the item next to faulty item.
General Description of Checking Method
Selecting 2 and subsequent items calls the submenu screen of each
item. And selecting 2 and subsequent items executes respective
menus and outputs the results.
For the contents of each sub menu, see “Check Items List” as below.
Check Items List:
0-2. Version
0-2-1. All
0-2-2. Revision
0-2-3. ROM Check Sum
0-2-4. Model Type
0-2-5. Region
0-3. EEPROM Check
0-3-1. Sampling Check
0-3-2. Detail Check
0-4. GP I/O Check
0-5. SD Bus Check
0-6. Video Check
0-2. Version
0-2-2. Revision
The revision number of ROM (IC206) that the program for
the DVD system processor (IC207) is stored.
0-2-3. ROM Check Sum
Check sum is calculated.
(4 digits hexadecimal number)
0-3. EEPROM Check
0-3-1. Sampling Check
EEPROM check at every 64 words.
It compares read data with write data of each address. When
there are discrepancies between two data, it displays error.
0-3-2. Detail Check
EEPROM check at every 1 word.
It compares read data with write data of each address. When
there are discrepancies between two data, it displays error.
0-4. GP I/O Check
Pull up/down setting check of the DVD system processor (IC207)
pin 150, 151 and 154 (for clock setting port).
0-5. SD Bus Check
SD bus data check between DVD decoder (IC701) and D-RAM
(IC706).
0-6. Video Check
Output the color bars for video level adjustment.
1. DRIVE AUTO ADJUSTMENT
On the Test Mode Menu screen, press the 1 button on the remote
commander, and the Adjustment Menu will be displayed.
## Drive Auto Adjustment ##
Adjustment Menu
0. ALL
1. DVD-SL
2. CD
3. DVD-DL
Exit: RETURN
Normally, 10/0 button is selected to adjust DVD (single layer), CD
and DVD (dual layers) in this order. But, individual items can be
adjusted for the case where adjustment is suspended due to an error.
In this mode, the adjustment can be made easily through the
operation following the message displayed on the monitor screen.
The disc used for adjustment must be the one specified for
adjustment.
1-0. ALL
Press the 10/0 button on the remote commander, and the servo set
data in EEPROM will be initialized. Then, 1. DVD-SL disc, 2. CD
disc and 3. DVD-DL disc are adjusted in this order.
Each time one disc was adjusted, it is ejected. Replace it with the
specified disc following the message. You can finish the adjustment
by pressing the RETURN button on the remote commander.
0-1. All (All items continuous check)
This menu checks all diagnostic items continuously. Normally, all
items are checked successively one after another automatically
unless an error is found, but at a certain item that requires judgment
through a visual check to the result, the following screen is displayed
for the key entry.
0-2-4. Model Type
Model name is displayed. (MHC-RVXXXD)
0-2-5. Region
Model destination code is displayed. (2 digits number)
27
HCD-RV777D/RV888D/RV999D
Note: During adjustment of each disc, the measurement for disc
type judgment is made. As automatic adjustment does not
judge the disc type unlike conventional models, take care
not to insert wrong type discs. Also, do not give a shock
during adjustment.
1-1. DVD-SL (single layer)
Press the 1 button on the remote commander and insert a DVD
single layer disc following the message. Then the adjustment will
be made through the steps below, then adjusted values will be written
to the EEPROM.
DVD Single Layer Disc Adjustment Steps:
1. Sled reset
2. Disc check memory SL
3. Wait 300 msec
4. Set disc type SL
5. LD on
6. Spindle start
7. Wait 1 sec
8. Focus servo on 0
9. Auto track offset adjust
10. CLVA on
11. Wait 500 msec
12. Tracking on
13. Wait 1 sec
14. Sled on
15. Check CLV on
16. Auto focus offset adjust
17. Auto focus gain adjust
18. Auto focus offset adjust
19. EQ boost adjust
20. Auto track gain adjust
21. All servo stop
22. EEP copy loop filter offset
1-2. CD
Press the 2 button on the remote commander and insert a CD disc
following the message. Then the adjustment will be made through
the steps below, then adjusted values will be written to the EEPROM.
CD Adjustment Steps:
1. Sled tilt reset
2. Disc check memory CD
3. Wait 500 msec
4. Set disc type CD
5. LD on
6. Spindle start
7. Wait 500 msec
8. Focus servo on 0
9. Auto track offset adjust
10. CLVA on
11. Wait 500 msec
12. Tracking on
13. (TC display start)
14. Wait 1 sec
15. Sled on
16. Check CLV on
17. Auto focus offset adjust
18. Auto focus gain adjust
19. Auto focus offset adjust
20. EQ boost adjust
21. Auto track gain adjust
22. All servo stop
1-3. DVD-DL (dual layers)
Press the 3 button on the remote commander and insert a DVD
dual layers disc following the message. Then the adjustment will
be made through the steps below, then adjusted values will be written
to the EEPROM.
DVD Dual Layers Disc Adjustment Steps:
1. Sled tilt reset
2. Disc check memory DL
3. Wait 500 msec
4. Set disc type DL
5. LD on
6. Spindle start
7. Wait 1 sec
Layer 1 Adjust
8. Focus servo on 0
9. Auto track offset adjust
10. CLVA on
11. Wait 500 msec
12. Tracking on
13. Wait 500 msec
14. Sled on
15. Check CLV lock
16. Auto loop filter offset adjust, Auto focus adjust
17. Auto focus gain adjust
18. Auto focus offset adjust
19. EQ boost adjust
20. Auto loop filter offset adjust
21. Auto track gain adjust
Layer 0 Adjust
22. Focus jump (L1 t L0)
23. Auto track offset adjust L0
24. CLVA on
25. Wait 500 msec
26. Tracking on
27. Wait 500 msec
28. Sled on
29. Check CLV lock
30. Auto focus adjust
31. Auto focus gain adjust
32. Auto focus offset adjust
33. EQ boost adjust
34. Auto track gain adjust
35. All servo stop
2. DRIVE MANUAL OPERATION
Note: This mode is used for design, and not used in service
fundamentally.
On the Test Mode Menu screen, press the 2 button on the remote
commander, and the Operation Menu will be displayed. For the
manual operation, each servo on/off control and adjustment can be
executed manually.
## Drive Manual Operation ##
Operation Menu
1. Disc Type
2. Servo Control
3. Track/Layer Jump
4. Non EEPROM Write Adjust
5. EEPROM Write Adjust
6. Memory Check
7. Disc Check Memory
8. Error Rate Display
9. SACD Water Mark
Exit: RETURN
28
HCD-RV777D/RV888D/RV999D
In using the manual operation menu, take care of the following
points. These commands do not provide protection, thus requiring
correct operation. The sector address or time code field is displayed
when a disc is loaded.
Note:
1. Set correctly the disc type to be used on the Disc Type
screen.
2. In case of an alarm, immediately press the x button to
stop the servo operation, and press the +/1 button to
turn the power off.
Basic operation:
(controllable from front panel or remote commander)
+/1 :Power OFF (release the Test Mode)
x :Servo stop
Z:Stop and eject/Loading
ENTER : Return to Operation Menu or Test
Mode Menu
. , >:Transition between sub modes of
menu
1 to 9 , 10/0 : Selection of menu items
Cursor o/O:Increase/Decrease in manually
adjusted value
2-1. Disc Type
Disc Type
Disc Type Select
1. Disc Type Auto Check
2. Set Disc Type DVD
3. Set Disc Type CD
4. Set Disc Type Hybrid
Exit: RETURN
2-1-1. Disc Type Auto Check
1) Press the 1 button on the remote commander to display the
Disc Type Auto Check screen.
2) Insert a disc and press the ENTER button on the remote
commander.
3) It judges the type of inserted disc automatically and displays
the disc type and so on as below.
Disc Type Auto Check
Disc Type xx
Layer xx
Mirr Time xx
Mirr Count xx
FZC Count xx
PI Reference xx
PI Peak xx
ENTER.Execute
Exit: RETURN
Disc Type : CD, DVD or Hybrid (SACD)
Layer : SINGLE, DUAL or HYBRID
Mirr Time : Mirror time of between disc surface and record
surface when disc type judgment. (hexadecimal
number)
Mirr Count : The number of times which mirror counts between
disc surface and record surface when disc type
judging.
FZC Count : The number of times which focus zero cross points
of each layer when lens down.
PI Reference: The average of PI reference voltage. (hexadecimal
number)
PI Peak : PI peak level voltage. It performs only when disc
type judgment is successful. (hexadecimal number)
2-1-2. Disc Type DVD
It sets up s that it may judge as a disc type of specification of the
disc with which the set was inserted.
[1]: DVD single layer disc (12 cm)
[2]: DVD dual layers disc (0 layer, 12 cm)
[3]: DVD dual layers disc (1 layer, 12 cm)
[4]: DVD-RW disc (12 cm)
[5]: DVD single layer disc (8 cm)
[6]: DVD dual layers disc (0 layer, 8 cm)
[7]: DVD dual layers disc (1 layer, 8 cm)
[8]: DVD-RW disc (8 cm)
2-1-3. Disc Type CD
It sets up so that it may judge as a disc type of specification of the
disc with which the set was inserted.
[1]: CD disc (normal speed, 12 cm)
[2]: CD disc (double speed, 12 cm)
[3]: CD disc (normal speed, 8 cm)
[4]: CD disc (double speed, 8 cm)
[5]: CD-RW disc (normal speed, 12 cm)
[6]: CD-RW disc (double speed, 12 cm)
[7]: CD-RW disc (normal speed, 8 cm)
[8]: CD-RW disc (double speed, 8 cm)
2-1-4. Disc Type Hybrid
It sets up so that it may judge as a disc type of specification of the
disc with which the set was inserted.
[1]: SACD Hybrid disc (SACD layer, 12 cm)
[2]: SACD Hybrid disc (CD layer, normal speed, 12 cm)
[3]: SACD Hybrid disc (CD layer, double speed, 12 cm)
[4]: SACD Hybrid disc (SACD layer, 8 cm)
[5]: SACD Hybrid disc (CD layer, normal speed, 8 cm)
[6]: SACD Hybrid disc (CD layer, double speed, 8 cm)
2-2. Servo Control
Note: Be sure to perform the disc type setup before performing
this item.
Servo Control
1.LD off R.Sled FWD
2.Focus off L.Sled REV
3.SPDL off U.Sled Reset
4.CLVA off D.Sled Limit
5.Trk. off
6.Sled off
7.Fcs.Srch off
0.All Servo Off
Exit: RETURN
On this screen, the servo on/off control necessary for replay is
executed. Normally, turn on each servo from 1 sequentially and
29
HCD-RV777D/RV888D/RV999D
for the selected item will be displayed, then increase or decrease
numeric value with the Obutton or obutton. If CLV has been
applied, the jitter is displayed for reference for the adjustment.
[1] Focus Offset : Adjusts focus offset.
[2] Focus Gain : Adjusts focus gain.
[3] Trk. Offset Coarse :
Adjusts tracking offset of the RF amp
(IC001) side.
[4] Trk. Offset Fine :
Adjusts tracking offset of the DSP (IC509)
side.
[5] Trk. Gain : Adjusts tracking gain.
[6] EQ Boost : Adjusts amount of boost of equalizer.
[10/0] :All servo off.
2-5. EEPROM Write Adjust
EEPROM Write Adjust
1. Focus Offset
2. Focus Gain
3. Trk. Offset Coarse
4. ——————
5. Trk. Gain
6. EQ Boost
0.All Servo Off
Exit: RETURN
On this screen, each item can be adjusted automatically. Select the
desired number 1 to 10/0 from the remote commander, and selected
item is adjusted automatically.
[1] Focus Offset : Adjusts focus offset.
[2] Focus Gain : Adjusts focus gain.
[3] Trk. Offset Coarse :
Adjusts tracking offset of the RF amp
(IC001) side.
[5] Trk. Gain : Adjusts tracking gain.
[6] EQ Boost : Adjusts amount of boost of equalizer.
[10/0] :All servo off.
2-6. Memory Check
Display images are shown as follows, and all two screens are able
to switch by the Obutton (UP) or obutton (DW).
EEPROM Data 1/2 CD SL L0 L1
Focus Gain xx xx xx xx
Trk. Gain xx xx xx xx
Focus Offset xx xx xx xx
Trk. Offset xx xx xx xx
EQ. Boost xx xx xx xx
PI Level xx xx -- --
Fcs. Balance -- xx -- --
Jitter xx xx xx xx
Mirror Time xx xx xx --
FE Level -- xx -- --
Traverse Lv1. -- xx -- --
Next:DW Default:CLR Exit:RET
when CLVA is turned on, the usual trace mode becomes active. In
the trace mode, DVD sector address or CD time code is displayed.
This is not displayed where the spindle is not locked.
The spindle could run overriding the control if the spindle system is
faulty or RF is not present. In such a case, do not operate CLVA.
[1] LD : Turn on/off the laser.
[2] Focus : Search the focus and turn on the focus.
[3] SPDL : Turn on/off the spindle.
[4] CLVA : Turn on/off normal servo of spindle servo.
[5] Trk. : Turn on/off the tracking servo.
[6] Sled : Turn on/off the sled servo.
[7] Fcs. Srch : Turn on/off the focus search.
[10/0] :All servo off.
[R] Sled FWD (right cursor) : Move the sled forward.
[L] Sled REV (left cursor) : Move the sled reverse.
[U] Sled FWD (up cursor) : Reset the sled.
[D] Sled REV (down cursor): Limit in the sled.
2-3. Track/Layer Jump
Track/Layer Jump
1. 1Tj FWD
2. 1Tj REV
3.500Tj Fine FWD
4.500Tj Fine REV
5.10kTj Dirc FWD
6.10kTj Dirc REV
7.20kTj Dirc FWD
8.20kTj Dirc REV
0. All Servo Off
Exit: RETURN
On this screen, track jump, etc. can be performed. Only for the DVD
dual layer disc, the focus jump and layer jump are displayed in the
right field
[1] 1Tj FWD : 1 track jump forward.
[2] 1Tj REV : 1 track jump reverse.
[3] 500Tj FWD: 500 track jump (fine search)forward.
[4] 500Tj REV : 500 track jump (fine search) reverse.
[5] 10kTj FWD: 10k track jump (direct search) forward.
[6] 10kTj REV : 10k track jump (direct search) reverse.
[7] 20kTj FWD: 20k track jump (direct search) forward.
[8] 20kTj REV : 20k track jump (direct search) reverse.
[10/0] :All servo off.
2-4. Non EEPROM Write Adjust
Non EEPROM Write Adjust
1. Focus Offset
2. Focus Gain
3. Trk. Offset Coarse
4. Trk. Offset Fine
5. Trk. Gain
6. EQ Boost
0.All Servo Off
Exit: RETURN
On this screen, each item can be adjusted manually. Select the desired
number 1 to 10/0 from the remote commander, and current setting
30
HCD-RV777D/RV888D/RV999D
2-9. SACD Water Mark Check (Not used)
SACD Water Mark Check
PSP AMP
PSN
Start: ENTER Stop: RETURN
On this screen, measure the PSP AMP value and PSN value of SACD
water mark.
3. MECHA AGING
On the Test Mode Menu screen, selecting 3 executes the aging of
the mechanism deck.
### Aging Test MENU ###
** Pls use over 40min. CD **
Operation Menu
1. Open/Close Test
Exit: RETURN
1) On the Aging Test MENU screen, press the 1 button on the
remote commander to display the Open/Close Test screen.
2) Insert discs and press the ENTER button on the remote
commander.
3) Is starts the aging.
During aging, the disc number, operating status and repeat cycle
are displayed. Aging can be aborted at any time by pressing
the ENTER button. After the operation is stopped, press the
ENTER button to return to the Aging Test MENU.
4. EMERGENCY HISTORY
On the Test Mode Menu screen, selecting 4 displays the information
such as servo emergency history.
The history information from last 1 up to 10 can be scrolled with
the Obutton or obutton. Also, specific information can be
displayed by directly entering that number with ten keys.
### EMG. History ###
Laser Hours CD xxxxhxxm
DVD xxxxhxxm
a. bb xx xx xx xx xx xx xx
xx xx xx xx xx xx xx xx
a. bb xx xx xx xx xx xx xx
xx xx xx xx xx xx xx xx
Select:1-9 Scroll:UP/DOWN
(1.Latest EMG.) Exit: RETURN
EEPROM Data 2/2 CDRW DVDRW
Focus Gain xx xx
Trk. Gain xx xx
Focus Offset xx xx
Trk. Offset xx xx
EQ. Boost xx xx
Prev:UP Default:CLR Exit:RET
On this screen, current servo adjusted data stored in the EEPROM
are displayed. The adjusted data are initialized by pressing the
CLEAR button, but be careful that they are not recoverable after
initialization.
Before clearing the adjusted data, make a note of the set data. This
screen will also appear if 0 -All is selected in the Drive Auto
Adjustment. In this case, default setting cannot be made.
2-7. Disc Check Memory
Disc Check Memory
1. SL Disc check
2. CD Disc check
3. DL Disc check
Exit: RETURN
On this screen, measure the mirror time of chucked disc, and write
to the EEPROM.
2-8. Error Rate Display
Error Rate Display
UC CR Address
PI1 Err Now xx xxxx xxxxxxxx
Max xx xxxx xxxxxxxx
Avg xx xxxx
PI2 Err Now xx xxxx xxxxxxxx
Max xx xxxx xxxxxxxx
Avg xx xxxx
PO Err Now xx xxxx xxxxxxxx
Max xx xxxx xxxxxxxx
Avg xx xxxx
Exit: RETURN
On this screen, measure and display the error rate.
UC : Incorrect value
CR : Correct value
Add : Address
31
HCD-RV777D/RV888D/RV999D
xxxxhxxm: The laser on total hours. Data below minutes are
omitted.
a. : Error number.
bb : Error code.
xx : Not used.
•Clearing History Information
Clearing laser hours:
Press the DVD DISPLAY and CLEAR buttons in this order.
Then both CD and DVD data are cleared.
Clearing emergency history:
Press the DVD TOP MENU and CLEAR buttons in this order.
Initializing set up data:
Press DVD MENU and CLEAR buttons in this order.
The data have been initialized when “EEPROM Initialize
Finished” message is displayed.
•Code list of Emergency History
10: Communication to RF amp (IC001) failed.
11: Each servo for focus, tracking, and spindle is unlocked.
12: Check sum error of EEPROM (IC204).
14: Communication to servo DSP (IC509) failed, or servo DSP
(IC509) is faulty.
15: Communication to DVD decoder (IC701) failed, or DVD
decoder (IC701) is faulty.
16: Communication to DSD decoder (IC801) failed, or DSD
decoder (IC801) is faulty. (Not used)
20: Initialization of sled servo failed. It is not placed in the ini-
tial position.
23: Sled servo operation error.
24: Made a request to move the sled servo to wrong position.
30: Tracking balance adjustment error.
31: Tracking gain adjustment error.
33: Focus bias adjustment error.
34: Focus gain adjustment error.
35: Equalizer adjustment error.
40: Focus servo does not operate.
41: With a DVD dual layers disc, focus jump failed.
50: CLV (spindle) servo does not operate.
51: Spindle does not stop.
60: Made a request to seek nonexistent address.
61: Seek error of retry more than regulated times.
70: Control data could not be read.
80: Disc reading failed.
5. MECHA ERROR HISTORY
On the Test Mode Menu screen, selecting [5] displays the information
of mechanism deck error history.
The history information from last 1 up to 8 can be scrolled with
the Obutton or obutton.
### Mecha Error History ###
1. aa bb cc dd ee xx xx xx
2. aa bb cc dd ee xx xx xx
3. aa bb cc dd ee xx xx xx
4. aa bb cc dd ee xx xx xx
5. aa bb cc dd ee xx xx xx
6. aa bb cc dd ee xx xx xx
7. aa bb cc dd ee xx xx xx
8. aa bb cc dd ee xx xx xx
Scroll:UP/DOWN
(1.Latest Err.) Exit: RETURN
aa: Initialization is completed or not.
FF : Complete.
other number: Not complete.
bb:Operating status of mechanism deck at an error occurred.
(lod sq jcp)
00 : Initializing.
10 to 15 : Open operating.
16 to 19 : Kicking cause open failed.
1A to 1F : Open operating.
20 to 27 : Complete the open operation.
28 : No disc and complete the open operation.
29 to 2F : Complete the open operation.
30 to 3F : Close requesting.
40 to 4F : Open requesting.
50 to 5F : Close operating.
60 to 6F : Complete the chucking operation.
80 to 8F : Complete the release operation.
(BU is home position)
90 to 9F : BU down operating.
A0 to AF : Opening/closing the shutter. Or stationary state in
open/close the shutter is enablement.
B0 to BF : BU up requesting.
C0 to CF : BU down requesting.
D0 to DF : BU upping.
E0 to EF : No disc checking in disc loading.
cc : Operating status of table at an error occurred.
(tbl sq jcp)
13 : The rotation stop position determination error of a table
11 to 12 : The loading position determination error of a table
dd: Operating status of mechanism deck at an error occurred.
(lod op jcp)
00 : Complete the operation.
10 to 1F : Open operating.
20 to 2F : Close operating.
30 to 3F : Release operating.
60 to 6F : Chucking operating.
70 to 7F : Kicking operating.
80 to 8F : Returning the BU to home position. (after kicking)
ee : The status of table operation. (“n” is unfixed)
(tbl op jcp)
1n : Rotating in the direction of a forward.
2n : Rotating in the direction of a reverse.
32
HCD-RV777D/RV888D/RV999D
6. VERSION INFORMATION
On the Test Mode Menu screen, selecting 6 displays the ROM
version and region code.
The parenthesized hexadecimal number in version field is checksum
value of ROM.
## Version Information ##
IF con. Ver.x. xx
SYScon. Ver.x. xx (xxxx)
Model MHC-RVXXXD
Region 0x
Config xxxxxxxx
Front End Ver.x.xx
Exit: RETURN
IF con. : The version of system controller (IC501).
SYScon. : The version of DVD system processor (IC207).
Front End: The version of mechanism controller (IC901).
7. VIDEO LEVEL ADJUSTMENT
On the Test Mode Menu screen, selecting 7 displays color bars for
video level adjustment. During display of color bars, OSD disappears
but the menu screen will be restored if pressing the ENTER button.
33
HCD-RV777D/RV888D/RV999D
SECTION 5
MECHANICAL ADJUSTMENTS
Precaution
1. Clean the following parts with a denatured alcohol-moistened
swab:
record/playback heads pinch rollers
erase head rubber belts
capstan idlers
2. Demagnetize the record/playback head with a head
demagnetizer.
3. Do not use a magnetized screwdriver for the adjustments.
4. After the adjustments, apply suitable locking compound to the
parts adjusted.
5. The adjustments should be performed with the rated power
supply voltage unless otherwise noted.
Torque Measurement
3.06 N • m to 6.96 N • m
31 to 71 g • cm
(0.43 – 0.98 oz • inch)
0.19 N • m to 0.58 N • m
2 to 6 g • cm
(0.02 – 0.08 oz • inch)
3.06 N • m to 6.96 N • m
31 to 71 g • cm
(0.43 – 0.98 oz • inch)
0.19 N • m to 0.58 N • m
2 to 6 g • cm
(0.02 – 0.08 oz • inch)
6.96 N • m to 14.02 N • m
71 to 143 g • cm
(0.98 – 1.99 oz • inch)
9.80 N • m
100 g or more
(3.53 oz or more)
9.80 N • m
100 g or more
(3.53 oz or more)
Mode Torque meter
CQ-102C
CQ-102C
CQ-102RC
CQ-102RC
CQ-201B
CQ-403A
CQ-403R
Meter reading
FWD
FWD
back tension
REV
REV
back tension
FF/REW
FWD tension
REV tension
34
HCD-RV777D/RV888D/RV999D
0 dB=0.775 V
DECK SECTION
1. Demagnetize the record/playback head with a head
demagnetizer.
2. Do not use a magnetized screwdriver for the adjustments.
3. After the adjustments, apply suitable locking compound to the
parts adjust.
4. The adjustments should be performed with the rated power
supply voltage unless otherwise noted.
5. The adjustments should be performed in the order given in this
service manual. (As a general rule, playback circuit adjustment
should be completed before performing recording circuit
adjustment.)
6. The adjustments should be performed for both L-CH and R-
CH.
7. Switches and controls should be set as follows unless otherwise
specified.
•Test Tape
Record/Playback Head Azimuth Adjustment
Note: Perform this adjustments for both decks
Procedure:
1. Mode: Playback
Tape Signal Used for
P-4-A063 6.3 kHz, –10 dB Azimuth Adjustment
DECK A DECK B
set
MAIN board
IC101
Pin 28 (L-CH)
Pin 37 (R-CH)
MAIN board
IC101
Pin 38 (GND)
+
–
level mete
r
test tape
P-4-A063
(6.3 kHz, –10 dB)
SECTION 6
ELECTRICAL ADJUSTMENTS
VIDEO SECTION
oscilloscope
set
J802
VIDEO OUTPUT
75
Ω
1.00
±
0.05 Vp-p
(WHITE 100%)
Video Level Check (VIDEO BOARD)
Purpose
This adjustment is made to satisfy the NTSC standard, and if not
adjusted correctly, the brightness will be too large or small.
Procedure:
1. Connect oscilloscope to VIDEO output.
2. Load a DVD reference disc playback.
3. Check the video signal level is 1.00±0.05Vp-p.
DVD SECTION
About the dicision to pass or fail of the optical pick-up block, refer
to “DICISION TO PASS OR FAIL OF THE OPTICAL PICK-UP
BLOCK” (see page 8)
TEST DISC LIST
Use the following test disc on test mode.
LUV-P01 (CD): PART No. 4-999-032-01
TDV-520CSO (DVD-SL): PART No. J-2501-236-A
TDV-540C (DVD-DL): PART No. J-2501-235-A
Note: Do not use exiting test disc for DVD.
AUTO SERVO ADJUSTMENT
After parts related to the servo circuit (RF amplifier (IC001), DSP
(IC509), motor driver (IC501), EEPROM (IC903) so on) are
replaced, re-adjusting the servo circuit is necessary. Select “ALL”
at “1. DRIVE AUTO ADJUSTMENT” (Refer to page 8 in TEST
MODE) and adjust DVD-SL (single layer), CD and DVD-DL (dual
layer).
35
HCD-RV777D/RV888D/RV999D
2. Turn the adjustment screw and check output peaks. If the peaks
do not match for L-CH and R-CH, turn the adjustment screw
so that outputs match within 1dB of peak.
3. Mode: Playback
4. After the adjustments, apply suitable locking compound to the
pats adjusted.
screw
position
L-CH
peak
within
1dB
output
level
L-CH
peak R-CH
peak
within
1dB
screw
position
R-CH
peak
MAIN
board
IC101
test tape
P-4-A063
(6.3 kHz, –10 dB)
pin 37
oscilloscop
e
L-CH
R-CH
VH
waveform of oscilloscope
in phase 45
°
90
°
135
°
180
°
good wrong
pin 38
pin 28
L
R
reverse forward
Adjustment Location: Playback Head (Deck A).
Record/Playback/Erase Head (Deck B).
36
HCD-RV777D/RV888D/RV999D SECTION 7
DIAGRAMS
7-1. IC PIN DESCRIPTIONS
• IC701 TMC57929PGF-RDP (DVD DECODER) (DMB07 Board (3/8))
Pin No. Pin Name I/O Pin Description
1, 2 D5, D6 I/O Two-way data bus signal input from/output to mechanism control IC.
3VSS — Ground pin
4D7I/O Two-way data bus signal input from/output to mechanism control IC.
5A0I/O Address signal input from/output to mechanism control IC.
6VDD — Power supply pin (+3.2 V)
7A1I/O Address signal input from/output to mechanism control IC.
8VDD5V — Power supply pin (+5 V)
9 to 14 A2 to A7 I/O Address signal input from/output to mechanism control IC.
15 VSS — Ground pin
16 XWAIT O Not used in this set. (Open)
17 XRD I Read strobe signal input from mechanism control IC.
18 XWR I Write strobe signal input from mechanism control IC.
19 XCS I Chip select signal input from mechanism control IC.
20, 21 XINT0, XINT1 O Interrupt signal output to mechanism control IC.
22 VDD — Power supply pin (+3.2 V)
23 XHRS I Not used in this set. (Open)
24 HDB7 I/O Stream data input from/output to DVD system processor IC.
25 VSS — Ground pin
26 HDB8 I/O Error flag signal input from/output to DVD system processor IC.
27 HDB6 I/O Stream data input from/output to DVD system processor IC.
28 VDDS — Power supply pin (+5 V)
29 HDB9 I/O Not used in this set. (Open)
30 HDB5 I/O Stream data input from/output to DVD system processor IC.
31 HDBA I/O Not used in this set. (Open)
32 HDB4 I/O Stream data input from/output to DVD system processor IC.
33 VSS — Ground pin
34 HDBB I/O Not used in this set. (Open)
35 HDB3 I/O Stream data input from/output to DVD system processor IC.
36 VDD — Power supply pin (+3.2 V)
37 HDBC I/O Not used in this set. (Open)
38 VDDS — Power supply pin (+5 V)
39 HDB2 I/O Stream data input from/output to DVD system processor IC.
40 HDBD I/O Not used in this set. (Open)
41 HDB1 I/O Stream data input from/output to DVD system processor IC.
42 VSS — Ground pin
43 HDBE I/O Not used in this set. (Open)
44 HDBO I/O Stream data input from/output to DVD system processor IC.
45 HDBF I/O Not used in this set. (Open)
46 HDRQ O Serial data effect flag signal output to DVD system processor IC.
47 VDDS — Power supply pin (+5 V)
48 XHWR I Serial data transfer clock signal input from DVD system processor IC.
49 XHRD I Not used in this set. (Open)
50 VDD — Power supply pin (+3.2 V)
51 REDY O Not used in this set. (Open)
52 VSS — Ground pin
53 XHAC I Serial data request signal input from DVD system processor IC. (DVD mode)
54 HINT I/O Not used in this set. (Fixed at H.)
55 XS16 I Not used in this set. (Fixed at H.)
56 HA1 I Not used in this set. (Fixed at H.)
57 XPDI I/O Not used in this set. (Fixed at H.)
58 VDDS — Power supply pin (+5 V)
37
HCD-RV777D/RV888D/RV999D
Pin No. Pin Name I/O Pin Description
59, 60 HA0, HA2 I Not used in this set. (Fixed at H.)
61 VSS — Ground pin
62, 63 HCS0, HCS1 I Not used in this set. (Open)
64 VDD — Power supply pin (+3.2 V)
65 DASP I/O Not used in this set. (Fixed at H.)
66 to 69 MDB0 to MDB3 I/O Two-way data bus signal input from/output to 16Mbit D-RAM IC.
70 VSS — Ground pin
71 MDB4 I/O Two-way data bus signal input from/output to 16Mbit D-RAM IC.
72 VDD5V — Power supply pin (+5 V)
73 to 75 MDB5 to MDB7 I/O Two-way data bus signal input from/output to 16Mbit D-RAM IC.
76 XMWR O Write enable signal output to 16Mbit D-RAM IC.
77 VDD — Power supply pin (+3.2 V)
78 XRAS O Row address strobe signal output to 16Mbit D-RAM IC.
79, 80 MA0, MA1 O Address signal output to 16Mbit D-RAM IC.
81 VSS — Ground pin
82 to 87 MA2 to MA7 O Address signal output to 16Mbit D-RAM IC.
88 VDD — Power supply pin (+3.2 V)
89 MA8 O Address signal output to 16Mbit D-RAM IC.
90 VSS — Ground pin
91 MA9/mnt0 O Address signal output to 16Mbit D-RAM IC.
92 MA10/mnt1 O EEPROM ready signal output to mechanism control IC.
93 MA11/mnt2 O Address signal output to 16Mbit D-RAM IC.
94 XMOE O Output enable signal output to 16Mbit D-RAM IC.
95 XCAS O Column address strobe signal output to 16Mbit D-RAM IC.
96, 97 MDB8, MDB9 I/O Two-way data bus signal input from/output to 16Mbit D-RAM IC.
98 VSS — Ground pin
99 MDBA I/O Two-way data bus signal input from/output to 16Mbit D-RAM IC.
100 VDD — Power supply pin (+3.2 V)
101, 102 MDBB, MDBC I/O Two-way data bus signal input from/output to 16Mbit D-RAM IC.
103 VDD5V — Power supply pin (+5 V)
104 to 106 MDBD to MDBF I/O Two-way data bus signal input from/output to 16Mbit D-RAM IC.
107 GFS O Guard frame sync signal output to mechanism control IC.
108 VSS — Ground pin
109 APE0 O Absolute phase error signal output
110 VDD — Power supply pin (+3.2 V)
111 DASY0 O RF binary signal output
112 GNDA5 — Ground pin
113, 114 ASF1, ASF2 O Filter connected pin for selection the constant asymmetry compensation.
115 DASY1 I Analog signal input after integrated from the RF binary signal.
116 RFDCC I Input pin for adjusting DC cut high-pass filter for RF signal.
117 RFIN I RF signal input from RS-232C. (for check)
118, 119 VCCA5, VCCA4 — Power supply pin (+3.2 V)
120 VCOR1 I VCO oscillating range setting resistor connected
121 VCOIN I VCO input
122, 123 GNDA4, GNDA3 — Ground pin
124 LPF5 O Inverted signal output to operation amplifier from PLL loop filter.
125 VC1 I Middle point voltage (+1.65 V) input
126, 127 LPF2, LPF1 I Inverted signal input from operation amplifier from PLL loop filter.
128, 129 VCCA3, VCCA2 — Power supply pin (+3.2 V)
130 PD0 O Signal output to charge pump for phase comparator.
131 PDHVCC O Middle point voltage output to RF PLL.
132 FDO O Signal output to charge pump for frequency comparator.
133, 134 GNDA2, GNDA1 — Ground pin
38
HCD-RV777D/RV888D/RV999D
Pin No. Pin Name I/O Pin Description
135 SPO O Spindle motor control signal output to focus/tracking coil driver, spindle/sled motor
driver IC.
136 VC2 I Middle point voltage (+1.65 V) input
137 MDIN2 I Spindle motor servo drive signal input
138 MDIN1 I MDP input
139 VCCA1 — Power supply pin (+3.2 V)
140 CLVS O Control signal output to selection the spindle control filter constant at CLVS.
141 VSS — Ground pin
142 MDSOUT O Frequency error output pin of internal CLV circuit.
143 VDD — Power supply pin (+3.2 V)
144 MDPOUT O Phase error output pin of internal CLV circuit.
145 DFCT I DFCT signal input
146 GSCOR I Guard subcode sync (S0+S1) detection signal input from CD decoder, digital servo
processor IC.
147 EXCK O Subcode serial data reading clock signal output to CD decoder, digital servo processor
IC.
148 SBIN I Subcode serial data input from CD decoder, digital servo processor IC.
149 VSS — Ground pin
150 SCOR I Subcode sync (S0+S1) detection signal input from CD decoder, digital servo
processor IC.
151 WFCK I Write frame clock signal input from CD decoder, digital servo processor IC.
152 VDD5V — Power supply pin (+5 V)
153 XRCI I Not used in this set. (Fixed at L.)
154 VDDS — Power supply pin (+5 V)
155 C2PO I C2 pointer signal input from CD decoder, digital servo processor IC.
156 VDD — Power supply pin (+3.2 V)
157 DBCK O Not used in this set. (Open)
158 BCLK I Bit clock signal (2.8224 MHz) input from CD decoder, digital servo processor IC.
159 DDAT O Not used in this set. (Open)
160 MDAT I Signal data input from CD decoder, digital servo processor IC.
161 VSS — Ground pin
162 DLRC O Not used in this set. (Open)
163 LRCK I L/R sampling clock signal (44.1 kHz) input from CD decoder, digital servo processor
IC.
164 XRST I Reset signal input from mechanism control IC. (L: reset)
165 IFS0 I Not used in this set. (Fixed at L.)
166 IFS1 I Not used in this set. (Fixed at H.)
167 XTAL I 33.8688 MHz clock signal input from clock generator IC.
168 VSS — Ground pin
169 XTL2 O 33.8688 MHz clock signal output to clock generator IC.
170 XTL1 I 33.8688 MHz clock signal input from clock generator IC.
171 VDD — Power supply pin (+3.2 V)
172 to 176 D0 to D4 I/O Two-way data bus signal input from/output to mechanism control IC.
39
HCD-RV777D/RV888D/RV999D
• IC901 CXP973064-243R (MECHANISM CONTROL) (DMB07 Board (5/8))
Pin No. Pin Name I/O Pin Description
1NO_USE O Not used. (Open)
2SDENO
Serial data enable signal output to CD/DVD/SACD RF amp, focus/tracking error amp
IC.
3DOCTRL/ISBTEST O Digital out ON/OFF control signal output to CD decoder, digital servo processor IC.
4XRST_2753 O Not used in this set. (Open)
5SDA_EEP I/O Data bus signal input from/output to EEPROM IC.
6MNT1 I EEPROM ready signal input from DVD decoder IC.
7FCS_JMP_1 O Focus jump 1 signal output to focus/tracking coil driver, spindle/sled motor driver IC.
8FCS_JMP_2 O Focus jump 2 signal output to focus/tracking coil driver, spindle/sled motor driver IC.
9SENS_CD I Internal status (SENSE) signal input from CD decoder, digital servo processor IC.
10 CDSP2 O CD spectrum signal output to CD decoder, digital servo processor IC.
11 CDSP4 O CD spectrum signal output to CD decoder, digital servo processor IC.
12 XCS_DVD O Chip select signal output to DVD decoder IC.
13 VSS — Ground pin
14 to 21 D0 to D7 I/O Two-way data bus signal input from/output to DVD decoder IC.
22, 23 INIT0_DVD, INIT1_DVD I Interrupt signal input from DVD decoder IC.
24 MSCK_SAMBA O Not used in this set. (Fixed at L.)
25 XRST_1882 O Reset signal output to DVD decoder IC.
26 SCOR I Subcode sync (S0+S1) detection signal input from CD decoder, digital servo processor
IC.
27 LAT_CD O Serial data latch pulse signal output to CD decoder, digital servo processor IC.
28 LDON O Laser diode ON/OFF control signal output to CD/DVD/SACD RF amp, focus/tracking
error amp IC.
29 MIRR I Mirror signal input from CD/DVD/SACD RF amp, focus/tracking error amp IC.
30 COUT_CD I Numbers of track counted signal input from CD/DVD/SACD RF amp, focus/tracking
error amp IC.
31 INLIM I Detection signal input from limit in switch. The optical pick-up is inner position when
H.
32 CS_ZIVA O Chip select signal output to DVD system processor IC.
33 SI_ZIVA I Serial data input from DVD system processor IC.
34 SO_ZIVA O Serial data output to DVD system processor IC.
35 SCK_ZIVA O Serial data transfer clock signal output to DVD system processor IC.
36 DRVIRQ O Interrupt request signal output to DVD system processor IC.
37 DRVRDY O Ready signal output to DVD system processor IC.
38 RST I System reset signal input from DVD system processor IC.
39 VSS — Ground pin
40 XTAL I System clock input (20 MHz)
41 EXTAL O System clock output (20 MHz)
42 VDD — Power supply pin (+3.2 V)
43, 44 SLED_A, SLED_B O Sled motor drive signal output to focus/tracking coil driver, spindle/sled motor driver
IC.
45 SCK_DSD O Clock signal output to DVD decoder IC.
46 SDOUT_DSD O Not used in this set. (Open)
47 SDIN_DSD I Not used in this set. (Open)
48 READY_DSD I Not used in this set. (Open)
49 DATA_CD O Serial data output to CD decoder, digital servo processor IC.
50 CLOK_CD O Serial data transfer clock signal output to CD decoder, digital servo processor IC.
51 XMSLAT O Not used in this set. (Open)
52 SQSO I Subcode Q data input from DVD decoder IC.
53 MUTE_DSD O Not used in this set. (Open)
54 SQCK O Subcode Q data reading clock signal output to DVD decoder IC.
55 VSS — Ground pin
40
HCD-RV777D/RV888D/RV999D
Pin No. Pin Name I/O Pin Description
56, 57 CONTROL_2, CONTROL_1 I Not used.
58 GFS_DVD I Guard frame sync signal input from DVD decoder IC.
59 MUTE_CD O Muting ON/OFF control signal output to CD decoder, digital servo processor IC.
60 MUTE_2D O Muting ON/OFF control signal output to focus/tracking coil driver, spindle/sled motor
driver IC.
61 SLED I Sled motor servo drive PWM signal input from CD decoder, digital servo processor IC.
62 FG I Spindle motor control signal input from CD/DVD/SACD RF amp, focus/tracking error
amp IC.
63 SP_ON O Muting ON/OFF control signal output to focus/tracking coil driver, spindle/sled motor
driver IC.
64 JIT I Jitter signal input
65 TE I Tracking error signal input from CD/DVD/SACD RF amp, focus/tracking error amp
IC.
66 PI I Pull in signal input from CD/DVD/SACD RF amp, focus/tracking error amp IC.
67 FE I Focus error signal input from CD/DVD/SACD RF amp, focus/tracking error amp IC.
68 AVSS — Ground pin
69 AVREF I Reference voltage input (for A/D converter)
70 AVDD — Power supply pin (+3.2 V) (for A/D converter)
71 GFS_CD I Guard frame sync signal input from CD decoder, digital servo processor IC.
72 SCLK_CD O SENSE serial data reading clock signal output to CD decoder, digital servo processor
IC.
73 TSD-M O Thermal shut down signal output to focus/tracking coil driver, spindle/sled motor
driver IC.
74 FOK_CD I Focus OK signal input from CD decoder, digital servo processor IC.
75 LOCK_CD I GFS is sampled by 460 Hz. (H input when GFS is H)
76 LDSEL O Laser diode selection signal output
77 SACD/DVD O SACD/DVD selection signal output
78 I2C_SIO I/O Communication data bus signal input/output
79 I2C_SCL I/O Communication data reading clock signal input/output
80 RXD I Serial data input from RS-232C. (for check)
81 TXD O Serial data output to RS-232C. (for check)
82 SDCLK_RF O Serial data transfer clock signal output to CD/DVD/SACD RF amp, focus/tracking
error amp IC.
83 SDATA_RF I/O Two-way data bus signal input from/output to CD/DVD/SACD RF amp,
focus/tracking error amp IC.
84 XWR O Write strobe signal output to DVD decoder IC.
85 XRD O Read strobe signal output to DVD decoder IC.
86 (PWE) — Not used in this set. (Fixed at H.)
87 VDD — Power supply pin (+3.2 V)
88 VSS — Ground pin
89 to 96 A0 to A8 O Address signal output to DVD decoder IC.
97 A8 O Power save control signal output to focus/tracking coil driver, spindle/sled motor
driver IC.
98 XDRST O Reset signal output to CD decoder, digital servo processor IC.
99 WP_EEP O Write protect signal output to EEPROM IC.
100 SCL_EEP O Clock signal output to EEPROM IC.
41
HCD-RV777D/RV888D/RV999D
• IC207 ZIVA5X-C2F (DVD SYSTEM PROCESSOR) (DMB07 Board (7/8))
Pin No. Pin Name I/O Pin Description
1VDDP — Power supply pin (+3.2 V) (I/O signal)
2HA1 I/O Address bus signal input from/output to bus interface IC.
3 to 11 HAD15 to HAD7 I/O Data bus (address signal multiplexed) signal input from/output to bus interface IC.
12 VDDP — Power supply pin (+3.2 V) (I/O signal)
13 GNDP — Ground pin (I/O signal)
14 to 19 HAD6 to HAD1 I/O Data bus (address signal multiplexed) signal input from/output to bus interface IC.
20 VDDP — Power supply pin (+3.2 V) (I/O signal)
21 GNDP — Ground pin (I/O signal)
22 HAD0 I/O Data bus (address signal multiplexed) signal input from/output to bus interface IC.
23 HDTACK I/O Not used in this set. (Fixed at H.)
24 HIRQ0 I Not used in this set. (Fixed at H.)
25 WEH.UDS I/O Host upper data strobe signal input from/output to programmable ROM IC.
26 WEL.LDS I/O Not used in this set. (Open)
27 HREAD I/O Read/write strobe signal input from/output to programmable ROM IC.
28 GPIO0(1) I/O Jig detection port
29 GND — Ground pin (inside core)
30 VDD — Power supply pin (+1.8 V) (inside core)
31 GND25 — Ground pin (SDRAM I/O signal)
32 VDD25 — Power supply pin (+3.2 V) (SDRAM I/O signal)
33 to 42 MA9 to MA0 O SDRAM address bus signal output to 128 Mbit SD-RAM IC.
43 GND25 — Ground pin (SDRAM I/O signal)
44 VDD25 — Power supply pin (+3.2 V) (SDRAM I/O signal)
45, 46 MA10, MA11 O SDRAM address bus signal output to 128 Mbit SD-RAM IC.
47, 48 BA1, BA0 O SDRAM bank select signal output to 128 Mbit SD-RAM IC.
49 MCS0 O SDRAM chip select signal output to 128 Mbit SD-RAM IC.
50 MCS1 O Not used in this set. (Open)
51 MRAS O SDRAM row address strobe signal output to 128 Mbit SD-RAM IC.
52 MCAS O SDRAM column address strobe signal output to 128 Mbit SD-RAM IC.
53 MWE O SDRAM write enable signal output to 128 Mbit SD-RAM IC. (H: read, L: write)
54 GND25 — Ground pin (SDRAM I/O signal)
55 VDD25 — Power supply pin (+3.2 V) (SDRAM I/O signal)
56 MCLK O SDRAM clock signal output to 128 Mbit SD-RAM IC.
57 to 60 MD0 to MD3 I/O SDRAM data input from/output to 128 Mbit SD-RAM IC.
61 GND25 — Ground pin (SDRAM I/O signal)
62 MDQM0 O Byte read/write mask signal output to 128 Mbit SD-RAM IC.
63 VDD25 — Power supply pin (+3.2 V) (SDRAM I/O signal)
64 to 71 MD4 to MD11 I/O SDRAM data input from/output to 128 Mbit SD-RAM IC.
72 GND25 — Ground pin (SDRAM I/O signal)
73 MDQM1 O Byte read/write mask signal output to 128 Mbit SD-RAM IC.
74 VDD25 — Power supply pin (+3.2 V) (SDRAM I/O signal)
75 to 78 MD12 to MD15 I/O SDRAM data input from/output to 128 Mbit SD-RAM IC.
79 GND — Ground pin (inside core)
80 VDD — Power supply pin (+1.8 V) (inside core)
81 to 84 MD16 to MD19 I/O SDRAM data input from/output to 128 Mbit SD-RAM IC.
85 GND25 — Ground pin (SDRAM I/O signal)
86 MDQM2 O Byte read/write mask signal output to 128 Mbit SD-RAM IC.
87 VDD25 — Power supply pin (+3.2 V) (SDRAM I/O signal)
88 to 95 MD20 to MD27 I/O SDRAM data input from/output to 128 Mbit SD-RAM IC.
96 GND25 — Ground pin (SDRAM I/O signal)
97 MDQM3 O Byte read/write mask signal output to 128 Mbit SD-RAM IC.
98 VDD25 — Power supply pin (+3.2 V) (SDRAM I/O signal)
99 to 102 MD28 to MD31 I/O SDRAM data input from/output to 128 Mbit SD-RAM IC.
42
HCD-RV777D/RV888D/RV999D
Pin No. Pin Name I/O Pin Description
103 GND25 — Ground pin (SDRAM I/O signal)
104 VDD25 — Power supply pin (+3.2 V) (SDRAM I/O signal)
105 VCLK I/O Not used in this set. (Open)
106 XCK_I/O_SEL I/O Not used in this set. (Open)
107 VS O S1 signal output
108 I/P SW O I/P select switch signal output
109 CDSEL O CD-DA select signal output
110 MREQ O Audio muting signal output to sound control IC.
111 VDDP — Power supply pin (+3.2 V) (I/O signal)
112 GNDP — Ground (I/O signal)
113 MDI O Serial data output to 2CH DAC IC (HCD-RV777D) and D/A converter IC (HCD-
RV888D/RV999D).
114 MC O Serial data clock signal output to 2CH DAC IC (HCD-RV777D) and D/A converter IC
(HCD-RV888D/RV999D).
115 ML O Latch enable signal output to 2CH DAC IC (HCD-RV777D) and D/A converter IC
(HCD-RV888D/RV999D).
116 HIRQ2 I Busy signal input from EEPROM IC.
117 VDAC_4B — Video DAC bias bit 4 (Connect to ground.)
118 VDAC_VDD4 — Power supply pin (+3.3 V) (Video DAC 4)
119 VDAC_4 O VDAC output 4
120 VDAC_3B — Video DAC bias bit 3 (Connect to ground.)
121 VDAC_VDD3 — Power supply pin (+3.3 V) (Video DAC 3)
122 VDAC_3 O VDAC output 3
123 VDAC_2B — Video DAC bias bit 2 (Connect to ground.)
124 VDAC_VDD2 — Power supply pin (+3.3 V) (Video DAC 2)
125 VDAC_2 O VDAC output 2
126 VDAC_1B — Video DAC bias bit 1 (Connect to ground.)
127 VDAC_VDD1 — Power supply pin (+3.3 V) (Video DAC 1)
128 VDAC_1 O VDAC output 1
129 VDAC_0B — Video DAC bias bit 0 (Connect to ground.)
130 VDAC_VDD0 — Power supply pin (+3.3 V) (Video DAC 0)
131 VDAC_0 O VDAC output 0
132 VDAC_DVSS — Ground pin (Video DAC digital system)
133 VDAC_DVDD — Power supply pin (+3.2 V) (Video DAC digital system)
134 VDAC_REFVDD — Power supply pin (+3.3 V) (Video DAC reference)
135 VDAC_REF I Reference voltage input (for Video DAC)
136 VDAC_REFVSS — Ground pin (Video DAC reference)
137 XVSS — Ground pin (crystal oscillator)
138 XOUT O Not used in this set. (Open)
139 XIN I Crystal oscillation signal input
140 XVDD — Power supply pin (+3.2 V) (crystal oscillator)
141 AVSS2 — Ground pin (analog PLL)
142, 143 AVDD2, AVDD1 — Power supply pin (+3.2 V) (analog PLL)
144 AVSS1 — Ground pin (analog PLL)
145 VDD — Power supply pin (+1.8 V) (inside core)
146 GND — Ground pin (inside core)
147 XCK O Audio system clock signal output to 2CH DAC IC (HCD-RV777D) and D/A converter
IC (HCD-RV888D/RV999D).
148 LRCK O LRCK signal output to 2CH DAC IC (HCD-RV777D) and D/A converter IC (HCD-
RV888D/RV999D).
149 BCK O BCK signal output to 2CH DAC IC (HCD-RV777D) and D/A converter IC (HCD-
RV888D/RV999D).
150 DATA0(DM) O Audio data (down mix signal) output to D/A converter IC (HCD-RV888D/RV999D).
43
HCD-RV777D/RV888D/RV999D
Pin No. Pin Name I/O Pin Description
151 DATA1(FLR) O Audio data (front L/R signal) output to 2CH DAC IC (HCD-RV777D) and D/A
converter IC (HCD-RV888D/RV999D).
152 VDDP — Power supply pin (+3.2 V) (I/O signal)
153 GNDP — Ground pin (I/O signal)
154 DATA2(SLR) O Audio data (rear L/R signal) output to D/A converter IC (HCD-RV888D/RV999D).
155 DATA3(CSW) O Audio data (center/subwoofer signal) output to D/A converter IC (HCD-RV888D/
RV999D).
156 IEC958 O S/PDIF signal output
157 DAI_DATA I Not used in this set. (Open)
158 DAI_BCK I Not used in this set. (Open)
159 DAI_LRCK I Not used in this set. (Open)
160 I2C_CL I/O I2C clock bus signal input from/output to mechanism control IC.
161 I2C_DA I/O I2C data bus signal input from/output to mechanism control IC.
162 CS(ZIVA_E2P) O Chip select signal output to EEPROM IC.
163 RXD1 I Serial data input from check jig
164 TXD1 O Serial data output to check jig
165 WRITE_CTRL(ZIVA_E2P) O Write control signal output to EEPROM IC.
166 GNDP — Ground pin (I/O signal)
167 VDDP — Power supply pin (+3.2 V) (I/O signal)
168 to 171 SDDATA7 to SDDATA4 I SDBUS data input from DVD decoder IC.
172 GND — Ground pin (inside core)
173 VDD — Power supply pin (+1.8 V) (inside core)
174 to 177 SDDATA3 to SDDATA0 I SDBUS data input from DVD decoder IC.
178 SDREQ O SDBUS data request signal output to DVD decoder IC.
179 SDEN I SDBUS data enable signal input from DVD decoder IC.
180 GNDP — Ground pin (I/O signal)
181 VDDP — Power supply pin (+3.2 V) (I/O signal)
182 SDERROR I SDBUS data error signal input from DVD decoder IC.
183 SDCLK I SDBUS data clock signal input from DVD decoder IC.
184 HIRQ1 I Interrupt signal input from mechanism control IC.
185 DRVCLK I Serial data clock signal input from mechanism control IC.
186 DRVTX I Serial data input from mechanism control IC and EEPROM IC.
187 DRVRX O Serial data output to mechanism control IC and EEPROM IC.
188 DRVRDY I Ready signal input from mechanism control IC.
189 VNW — Power supply for 5 V tolerance voltage input
190 ALE O Latch enable signal output for address data demux.
191 RST_SPC O Reset signal output to mechanism control IC.
192 INT/EXT O Not used in this set. (Open)
193 HCS2 O Not used in this set. (Open)
194 HCS1 I/O Not used in this set. (Open)
195 HCS0 O Chip select signal output to programmable ROM IC.
196 VDDP — Power supply pin (+3.2 V) (I/O signal)
197 TRST I Reset signal input
198 TDO O Data output
199 TDI I Data input
200 TMS I TMS signal input
201 TCK I TCK signal input
202 RESET I ZIVA reset signal input
203 BUS CLK I/O Not used in this set. (Open)
204 GND — Ground pin (inside core)
205 VDD — Power supply pin (+1.8 V) (inside core)
206, 207 HA3, HA2 I/O Address bus signal input from/output to bus interface IC.
208 GNDP — Ground pin (I/O signal)
44
HCD-RV777D/RV888D/RV999D
• IC701 M30620MCN-A38FPU0 (MASTER CONTROL) (MAIN Board (3/3))
Pin No. Pin Name I/O Pin Description
1S-OUT O Serial out signal output
2S-CLK O Serial clock signal output
3M61530-CLK O M61530FP clock signal output
4SIRCS I Sircs signal input
5M61530-DATA O M61530FP data signal output
6M61530-DATA O M61530FP data signal output
7M61537-CLK O M61537FP clock signal output
8EXT.BUS-INPUT I External bus input with selector input (Fixed at L.)
9PROCESSOR.MODE-SW I Processor mode switch signal input (Fixed at L.)
10 SUB.CLOCK-IN I Sub clock signal input (32.768 kHz)
11 SUB.CLOCK-OUT O Sub clock signal output (32.768 kHz)
12 RESET I System reset signal input
13 SYSTEM.CLOCK.OUT OSystem clock signal output (16 MHz)
(16M)
14 VSS — Ground pin
15 SYSTEM.CLOCK.IN (16M) I System clock signal input (16 MHz)
16 VCC — Power supply pin (+3.3 V)
17 PULL.UP (EVER3.3V) I Pull up (EVER +3.3 V)
18 RDS-INT I RDS clock signal input Not used in this set. (Fixed at L.)
19 NO-USE I Not used. (Fixed at L.)
20 AC-CUT I AC cut select signal input (L: ON, H: OFF)
21 RDS-DATA I Not used in this set. (Fixed at L.)
22 ST-MUTE O Stereo mute select signal output (L: OFF, H: ON)
23 STEREO I Stereo select signal input (L: ON, H: OFF)
24 TUNED I Tuned select signal input (L: ON, H: OFF)
25 ST-CE O Stereo chip enable signal output
26 ST-DOUT O Stereo data out signal output
27 ST-DIN I Stereo data in signal input
28 ST-CLK O Stereo clock signal output
29 IIC-CLK I/O IIC clock signal input/output
30 IIC-DATA I/O IIC data input/output
31 SYS-POWER O System power select signal output (L: OFF, H: ON)
32 SYS-RESET O System reset signal output
33 M-REQ I DAC mute request select signal input from ZIVA. (L: ON, H: OFF)
34 VIDEO-MUTE2 O Video mute 2 select signal output (L: ON, H: OFF)
35 VIDEO-MUTE1 O Video mute 1 select signal output (L: ON, H: OFF)
36 VIDEO-OUT-SW O Video out switch select signal output (L: DVD, H: other)
37 REAR-MUTE O Surround (rear) mute select signal output (L: ON, H: OFF)
38 CENTER-MUTE O Center mute select signal output (L: ON, H: OFF)
39 SWFR-MUTE O Sub woofer mute select signal output (L: ON, H: OFF)
40 to 44 NO-USE O Not used. (Fixed at L.)
45 M-RESET O Reset signal output
46 STANDBY-LED O Standby LED control signal output (L: OFF, H: ON)
47 TBL-POS O Table motor drive control signal output (+)
48 TBL-NEG O Table motor drive control signal output (–)
49 LOD-POS O Loading motor drive control signal output (+)
50 LOD-NEG O Loading motor drive control signal output (–)
51 ENCODER-SW1 I Disc tray address signal input (Disc 1)
52 ENCODER-SW2 I Disc tray address signal input (Disc 2)
53 ENCODER-SW3 I Disc tray address signal input (Disc 3)
54 EJECT-SW I Open/close select signal input (L: open, H: close)
55 T-SENS I Table sensor signal input
45
HCD-RV777D/RV888D/RV999D
Pin No. Pin Name I/O Pin Description
56 HP-SW I Headphones in/out select signal input (L: out, H: in)
57 MIC-SW I Microphone in/out select signal input (L: out, H: in)
58 A-TRG O Trigger out ON/OFF select signal output (deck A) (L: OFF, H: ON)
59 B-TRG O Trigger out ON/OFF select signal output (deck B) (L: OFF, H: ON)
60 A-SHUT-IN I Reel pulse signal input (deck A)
61 B-SHUT-IN I Reel pulse signal input (deck B)
62 VCC — Power supply pin (+3.3 V)
63 NO-USE I Not used in this set. (Open)
64 VSS — Ground pin
65 CAPM-CONT O Capstan motor ON/OFF select signal output (L: OFF, H: ON)
66 B-REC.FWD I REC (FWD) switch in signal input (deck B) (active L)
67 B-REC.REV I REC (REV) switch in signal input (deck B) (active L)
68 A-HALF I Half in signal input (deck A) (active L)
69 B-HALF I Half in signal input (deck B) (active L)
70 A-PLAY I Playback switch in signal input (deck A) (active L)
71 B-PLAY I Playback switch in signal input (deck B) (active L)
72 AMS-IN I AMS in select signal input (L: without music, H: with music)
73 DISPLAY-KEY I Display key signal input (active L)
74 POWER-KEY I Power key signal input (active L)
75, 76 NO-USE I Not used in this set. (Fixed at L.)
77 BIAS O Bias ON/OFF select signal output (L: OFF, H: ON)
78 AMS MUTE O AMS mute select signal output
79 TC-RELAY O Tape REC/PB control signal output (H: REC, L: PB (other))
80 PB-MUTE O PB mute select signal output (L: ON, H: OFF)
81 REC-MUTE O REC mute select signal output (L: ON, H: OFF) Not used in this set. (Open)
82 NO-USE I Not used in this set. (Fixed at L.)
83 LINEOUT-MUTE O MD (VIDEO) mute ON/OFF select signal output (L: ON, H: OFF)
84 LINE-MUTE O TA line mute ON/OFF select signal output (L: ON, H: OFF)
85 STK-MUTE O STK mute ON/OFF select signal output (L: ON, H: OFF)
86 PROTECT I Protect ON/OFF select signal input (L: ON, H: OFF)
87 STB-RELAY O Standby relay ON/OFF select signal output (L: OFF, H: ON)
88 FRONT-RELAY O Front speaker relay ON/OFF select signal output (L: OFF, H: ON)
89 REAR-RELAY O Rear/center/sub woofer speaker relay ON/OFF select signal output (L: OFF, H: ON)
90 VACS-IN2 I VACS in 2 signal input (thermal VACS)
91 VACS-IN1 ILLUMI-IN I VACS & Illumi in 1 signal input (A/D)
92 FAN CONT O Fan motor control signal output (L: OFF, H: 300 msec)
93 FAN ON/OFF O Fan motor ON/OFF select signal output (L: ON, H: OFF)
94 MODEL-IN I Model in signal input (A/D)
95 SPEC-IN I Destination in signal input (A/D)
96 AVSS — Analog ground pin
97 NO-USE I Not used in this set. (Fixed at L.)
98 V.REF — AV reference voltage pin (+3.3 V)
99 AVCC — Power supply pin (+3.3 V)
100 S-IN I Serial in signal input
46
HCD-RV777D/RV888D/RV999D
• IC101 µPD780232GC-504-8BT-A (SYSTEM CONTROL) (PANEL Board)
Pin No. Pin Name I/O Pin Description
1VDD — Power supply pin (+3.3 V)
2VSS — Ground pin
3X1ISystem clock signal input (5 MHz)
4X2ISystem clock signal input (5 MHz)
5ICIDirectly connect to ground.
6RESET I Reset signal input (active L)
7S-CLK I Serial clock signal input
8S-IN I Serial data in signal input
9S-OUT O Serial data out signal output
10 to 14 NC-L O Not used in this set. (Fixed at L.)
15 VOL-A I VOLUME encoder in A signal input
16 VOL-B I VOLUME encoder in B signal input
17 NC-L I Not used in this set. (Fixed at L.)
18 AVSS — Analog ground pin
19 NC-L I Not used in this set. (Fixed at L.)
20 to 22 KEY3 to KEY1 I Key in signal input
23 VSS — Ground pin
24 AVDD — Analog power supply pin (+3.3 V)
25 VDD — Power supply pin (+3.3 V)
26 to 33 NC-L I Not used in this set. (Fixed at L.)
34 to 39 PS07 to PS12 O Illumination LED drive control signal output (L: OFF, H: ON)
40 MULTI/I-BASS O Not used in this set. (Fixed at L.)
41 NC O Not used. (Open)
42, 43 NC-L O Not used in this set. (Fixed at L.)
44 to 58 S1 to S15 O FL segment control signal output (L: OFF, H: ON)
59 VDD — Power supply pin (+3.3 V)
60 V.LOAD I V.LOAD signal input
61 to 66 S16 to S21 O FL segment control signal output (L: OFF, H: ON)
67 to 80 G1 to G13 O FL grid control signal output (L: OFF, H: ON)
47 47
HCD-RV777D/RV888D/RV999D
HCD-RV777D/RV888D/RV999D
7-2. BLOCK DIAGRAM — DVD DSP SECTION —
1
57
27
40
39
38
48
47
46
26
4
3
6
5
12
11
10
9
16
15
14
13
17
18
21
23
24
36
37
34
35
20
A+5V
CDPD
DVDPD
CDLD
DVDLD
VC
MIRR
PI/CE
SDEN
DATA RF
CLK RF
LDON
CD E
CD F
CD D
CD C
CD B
CD A
D
C
B
A
C2
D2
A2
B2
DVDRFP
63 RFSIN
50 RFAC
20 MIRR
65
44,41,39,35
32,30,27,24
LRCK
46HDRQ
HDB0-HDB7
48XHWR
53XHAC
76
66,-69,71,
73-75,
96,97,99,
101,102,
104-106
16MBIT D-RAM
IC706
128MBIT SD-RAM
IC203
79,80,
82-87,
89,91
16
10 21-24,
27-32
2-5,
7-10,
41-44,
46-49
17
18
33
34
35
XMWR
78XRAS
MDB0-MDBF
94XMOE
95XCAS
92MNT1
170XTL1
107GFS
SPIN
WE
OE
A0-A9
MA0-MA9
I/O0-I/O15
RAS
UCAS
LCAS
66PCMD
67
BCK
79SBSO
80EXCK
10WFCK
14C2PO
15SCOR
IC703 (2/2)
57
DVD DECODER
IC701
17
WDCK
25
MDP
71
XTAI
39 FE
40 SE
41 TE
43 RFDC
163 LRCK
117 RFIN
160 MDAT
158 BCLK
148 SBIN
147 EXCK
151 WFCK
155 C2PO
150 SCOR
146 GSCOR
21
DFCT 145 DFCT
137 MDIN2
135 SPO
109 APE0
88
33 FFDR
34 FRDR
DO1+
DO1-
48
IN1+
1
IN1-
3
IN2+
4
IN2-
13
IN5-
45
OUT5
7
IN3-
10
IN4-
LDSEL
TSD M
SPON
MUTE 2D
A8
DO2+
FFDR
FRDR
TFDR
TRDR
DO2-
27
28
47
46
32
31
SPINDLE
MOTOR
SLED
MOTOR 30
29
22 39
21
76 73 63 60 97
SLED A
SLED B
43 44
FG
LDON
62 28
SDCLK RF
SDATA RF
82 83
SDEN
FCS JMP2
28
FCS JMP1
PI
766
TE
FE
65 67
MIRR
SLED
29 61
INLIM
SQSO
31 52
SQCK
DOCTRL/ISBTEST
54 3
XDRST
MUTE CD
98 59
DATA CD
LAT CD
CLOCK CD
SENS CD
SCLK CD
GFS CD
COUT CD
FOK CD
LOCK CD
SCOR
JIT
49 27 50 9 72 71 30 74 75
CDSP2
10 26 64
SCK DSO
45
IC703 (1/2)
13
2
XRD
85
XWR
84
XCS DVD
12
INITO DVD
22
INITO DVD
23
MECHANISM
CONTROL
IC901
CLR
SWITCHING
IC902
13
6
7
8
D+3.3V REG
IC907
31
3
99
5
EEPROM
IC903
SWITCH
IC111
100
7
5
6
GFS DVD
58
CS ZIVA
SI ZIVA
SO ZIVA
SCK ZIVA
32
CLOCK GENERATOR
IC906
Q202
EEPROM
IC204
FLIP FLOP
IC904
HA1-3
HA12-19
HA1,2
BUS INTERFACE
IC231
BUS INTERFACE
IC232
BUS INTERFACE
IC233
LE
2-9 12-19
Q
2
D+3.3V
SDA
42S
11S
2D
1D
3
6
MO1
10 SO2
13 SO3
SCL
WP
SDA EEP
SCL EEP
WP EEP
D+5V
1
CK
8
190
47
195
25
27
26
22,19-14,
11-3
2,207,206
11
11
28
139
188
165 186187162 185 184 116 191 161 160
WC
DRVRDY
BA1
48 BA0
49 MCSO
51 MRAS
52 MCAS
62,73,86,97
42-33,
45,46
57-60,
64-71,
75-78,
81-84,
88-95,
99-102
25-27,
60-66,
24,21
16,71,28,59
53 MWE
183
178
SDCLK
SDREQ
MD0-MD31
DQ0-DQ31
A0-A9,A10/AP,NC
SDDATA0-SDDATA7
179 SDEN
26HDB8 182 SDERROR
MDQM0-MDQM3
DQM0-DQM3
MA0-MA11
CE
WE
OE
WC (ZIVA E2P)
202
RESET
SSTP
CS (ZIVA E2P)
DRVRX
DRVTX
DRVCLK
HIRQ1
HIRQ2
RST SPC
I2C DA
I2CCL
GPIOO
HAD0-15
6
DO
5
DI
ALE
23
BS1
56 MCLK
68
CLK
67
CKE
22
BS0
20
CS
19
RAS
18
CAS
17
WE
HCSO
HA1-3
HRD0-15 HAD0-7
LE
12-19 2-9
11
LE
7-9 12-14
11
WEH.UDS
HREAD
125
122
119
107
131
128
VDAC 0
VDAC 1
VDAC 2
VDAC 3
VDAC 4
154
151
150
DATA1(FLR)
DATA0(DM)
BCK
156
155
IEC958
DATA2(SLR)
DATA3(CSW)
147
109
CDSEL
MREQ
149
148LRCK
XCK
113
DVD SYSTEM PROCESSOR
IC207
DAC
SECTION
MDI
115
114
ML
MC
VS
XIN
4
SK
3
CS
1
R/B
XTI
XTO
4
SYS-RESET
I2C CLK
I2C DATA
3534
DRVRDY
37
DRVIRQ
3633
RST
38
I2C SIO
78
I2C SCL
79
TXD
81
XRST 1882
25
MNT1
614-21 89-96
D0-D7 A0-A7
20 19
LASER DIODE
SELECT
Q901
40
41
DO4-
TSD M
MUTE5
MUTE34
MUTE12
POWER SAVE
DO4+
DO3-
DO3+
IN6-
IN6+
DO5-
DO5+
SPDL+
SPDL-
SLA+
SLA-
SLB+
SLB-
A+3.3V
31 TFDR
32
IC503
TRDR
29 SFDR
5
6
7
3
14
IC003
30
26
SQSO
76
XRST
2
MUTE
3
DATA
4
XLAT
5
SQCK
77
MD2
63
CLOCK
6
SENS
7
SCLK
8
GFS
13
COUT
19
FOK
22
LOCK
24
XTSL
69
XRST
164
XINT1
21
XINT0
20
XCS
19
XWR
18
17
XRD
172-176
1,2,4
5,7,
9-14
D0-D7 A0-A7
SRDR
FCS+
FCS-
TRK+
TRK-
INLIM 3V
INLIM
SW
XTAL
EXTAL
VCC
GND
SDEN
SDATA
SCLK
LDON
MIRR
PI
31
MIN
32
MEVO
RFAC
FE
TE
PD
LD GND
CDLD
DVDLD
VC
F
E
D
C
A
B
RF
CD/DVD/SACD RF AMP,
FOCUS/TRACKING ERROR AMP
IC001
FOCUS/TRACKING COIL DRIVER,
SPINDLE,SLED MOTOR DRIVER
IC501
CD DECODER,
DIGITAL SERVO PROCESSOR
IC509
OPTICAL PICK-UP
BLOCK
X901
20MHz
9177-174,
171-168
2,4,5,7,
8,10,11,13
74,76,77,79,
80,82,83,85,
31,33,34,36,
37,39,40,42,
45,47,48,50,
51,53,54,56
32
12
4
28
X902
27MHz
1-10,13,
16-25,48
29-36,
38-45
HA1-HA22
DQ0-DQ15
HA1-22
HAD8-15
HA20-22
HA4-11
HAD0-15
PROGRAMMABLE ROM
IC206
V
MDI
MC
ML
MREQ
CDSEL
XCK2
BCK-ZIBA2
LRCK-ZIBA3
DATA0
DATA1(SEL)
DATA2
DATA3
IEC958
C
Y/G
CB/R
CR/B
WIDE
108
I/P SW I/P SW
A
MAIN
SECTION
B
DVD SYS
SECTION
C
M
M
• Signal path
:DVD (AUDIO)
:DVD (RF)
:DVD (DIGITAL)
110
AUTOMATIC
POWER CONTROL
(FOR DVD)
Q001
22
AUTOMATIC
POWER CONTROL
(FOR CD)
Q002
(Page 48)
(Page 49)
(Page 50)
4848
HCD-RV777D/RV888D/RV999D
HCD-RV777D/RV888D/RV999D
1
2
5
6
31
45
46
47
40
41
38
34
35
36
54 5
3
39
38
37
89
49
50
7
9
4
2
51
52
53
55
15 14 13 16 3 1 2
8 7
MUTE
Q375
OVERLOAD
DETECT
TH301,Q316,317
OVERLOAD
DETECT
Q341
OVERLOAD
DETECT
Q351
MUTE
Q373
MUTE CONTROL
Q721
MUTE CONTROL
Q719,724
MUTE
Q377
DIGITAL OPTICAL
TRANSMITTER
IC302
MASTER CONTROL
IC701 (1/3)
2CH DAC
IC331
EJECT SW
SW1
DATA4
DATA1
VOUT3
DOWN MIX
FRONT
VOUT4
VOUT7
VOUT6
VOUT5
VOUT1
VOUT2
VOUT8
DATA2
DATA3
BCK
LRCK
SCKI
MDI R-CH
R-CH
R-CH
MC
ML
DATA0
ICE958
RV777D
RV777D
CDSEL
DATA1(SEL)
DATA2
DATA3
BCK-ZIBA2
LRCK-ZIBA3
XCK2
MDI
MC
ML
ML
MC
MD
SCK
LRCK
BCK
R-CH
DATA
LOUT
ROUT
TONE
SW
MUTE
SW2
SW3
T-SENS
DATA
CLK
CENTER MUTE
REAR RELAY
REAR MUTE
NEG
POS
SWFR MUTE
RV888D/RV999D
IC701
M751
(LOADING)
M741
(TABLE)
LOADING
MOTOR
DRIVE
M
47
48
7
9
4
2
NEG
POS
IC712
TABLE
MOTOR
DRIVE
M
D/A CONVERTER
IC302
12
11
10
16
20
14
13
9
Q731
IC731
TABLE
ADDRESS
SENSOR
Q384
RV888D/RV999D
RV777D
12
13
4
15
POWER AMP
IC301
SURROUND CONTROL
IC301
CH2
CH3
6
3
13
37
41
14
15
29
25
38
34
17 18
22
DATA
CLK
IN SUR
LINK IN
IN C
IN SW
SW IN
IN DM
IN F
OUT
AMP
IC303
5 7
OUT
OUT
OUT
OUT
R-CH +VL
R-CH
R-CH
PROTECT
DC DET
OVERLOAD DET
RY381
Q381
J102
TM401
+VL
Q383
RY382
CLOSE OPEN
RE701
ENCODER
M61530
LODTBL
OPTICAL OUT SELECTOR
IC252
L
R
F
MAIN
SECTION
SURROUND
SPEAKER
CENTER
SPEAKER
SUB WOOFER
OUT
E
D
MAIN
SECTION
A
DVD DSP
SECTION
S751
OPEN/CLOSE
DETECT
DISC TRAY
ADDRESS
DETECT
DVD
DIGITAL OUT
(OPTICAL)
MAIN
SECTION
RV888D/RV999D
• Signal Path
: DVD (AUDIO)
: AUDIO
: DVD (RF)
• R-CH is omitted due to same as L-CH.
: DVD (DIGITAL)
(Page 47)
(Page 49)
(Page 49) (Page 49)
7-3. BLOCK DIAGRAM — DAC SECTION —
49 49
HCD-RV777D/RV888D/RV999D
HCD-RV777D/RV888D/RV999D
17
LINE
REC(DECK B)
PB(DECK A)
PB(DECK B)
TUNER
DOWN MIX
MIC
GAME
76
7
RELAY
SWITCH
3
4
75
L
R
FAN
SWITCH
J501
BIAS OSC
Q601
T601
B
DVD DSP
SECTION
R-CH
DDAC
SECTION
FDAC
SECTION
E
DAC
SECTION
1
2
FRONT 57
R-CH
R-CH
A+9V
J104
ECHO AMP
IC502
AMS OUT
LINE
GAME
MIC
RECB1
67
35 34
DATA
CLOCK
DATA
CLOCK
57 MIC SW
91
IN1
VACS
90
IN2
VIDEO
86
PROTECT
80
PB MUTE
84
LINE-MUTE
85
STK-MUTE
56
HP SW
88
FRONT-RELAY
92
FAN CONT
93
FAN ON/OFF
36
VIDEO OUT-SW
33
M-REQ
34
MUTE1
35
MUTE2
83 LINE OUT MUTE
72 AMS-IN
AMS MUTE
77 BAIS
78
79 TC-RELAY
PB B
DM
SUR1
INB1
PB A
REC
28LOUT
29SW
80
1
23TONE
SW
TONE
MUTE
27
BBB1
25
53
BBA1
POWER AMP
IC201
REC/PB AMP,
SOUND CONTROLLER
IC101
MASTER CONTORL
IC701 (2/3)
7
6
15
13
OVERLOAD
DET
Q201
8
TM901
LCH
3
DATA
2
DO
5
+9V
10
RCH
DBFB
DET AC
DET
DBFB
SWITCH
Q112
R-CH
PROTECT
DET
R-CH
Q233,234
+VH
RY281
23CVBS OUT
4CVBS IN
V
MREQ
6Y-IN
Y/G 2C-IN
C
12
16
3
13
CB-IN
25 S1
9I/P
MUTE1
MUTE2
CR-IN
10 CY-IN
CR/B
CB/R
WIDE
I/P SW
S-DC OUT
C OUT
27
26
COMPONENT
VIDEO BUFFER
IC801
VIDEO SELECTOR
IC802
21Y OUT
20CY OUT
18CB OUT
16CR OUT
VIDEO
OUT
J802
COMPONENT
VIDEO OUT
J801
FRONT
SPEAKER
GAME
INPUT
S VIDEO
OUT
J803
C
Y
7
3
1
2
Y
P
B
/C
B
P
R
/C
R
TM201
Q801
Q191
Q221,222
MUTE
Q171
PB MUTE
Q111,607,608
IN
ST-BY
+RE
-RE
LINE MUTE
Q702,703,707
AC DET
Q704,705
D230,231
MUTE
Q232
MUTE
Q143
MUTE
CONTROL
Q713,714,
Q708-710
Q281,282
R-CH
OVERLOAD DET
DC DET
PROTECT
R-CH
OVERHEAT
DET
TH201,Q216,217
AC4
M61537
J503
RV501
MIC
MIC LEVEL
MIC AMP
IC501 (1/2)
MIC AMP
IC501 (2/2)
RV502
EXCEPT RV999D:E51,
AR,MX MODEL
ECHO LEVEL
IN L
R
OUT L
R
AUDIO L
R
R-CH
VIDEO/SAT
VIDEO
R-CH
27 DIN
26 DOUT
28 CLK
25 CE ST
22 MUTE
23 STEREO
R-CH
Q602,603
Q627,
Q628
A+9V
ERASE
HEAD
REC/PB
HEAD R-CH
R-CH
PB
HEAD
MUTE CONTROL
Q629-631
MUTE CONTROL
Q623,624
MUTE
Q622
J502
PHONES
R-CH
AC3
FAN901
FAN
(DECK A)
HP901
HRPE901
(DECK B)
TAPE
MECHANISM
DECK
BLOCK
B-REC.REV
B-SHUT61
A-SHUT
60
B-PLAY71
70
69
68
67
58
A-PLAY
B-HALF
A-HALF
A-TRIGA SOL
B REC(REV)
B PHOTO
A PHOTO
B MODE
A MODE
B HALF
A HALF
B-REC.FWD
66
B REC(FWD)
65
B-TRIG
B SOL 59
CAP M-CONT
CAP M+
B SOL DRIVE
Q617,618
CAP M DRIVE
Q615,616
A SOL DRIVE
Q613,614
1
CLOCK
4
CE
11
MUTING
6
TUNED
7
STEREO
DOUT
DIN
CLK
CE
MUTE
TUNED
STEREO
24 TUNED
LINE OUT
MUTE CONTROL
Q723
MUTE
Q142
AMS
DETECT
Q661,662
AMS
MUTE
Q604-606
IC203
3
4
11
AMS IN
8
2
6
59
13
AM
FM 75Ω
COAXIAL
MUTE CONTROL
Q701
• Signal Path
: TUNER
: AUDIO
: PB (DECK A)
: PB (DECK B)
: REC (DECK B)
• R-CH is omitted due to same as L-CH.
(Page 48)
(Page 48)
(Page 48)
(Page 47)
7-4. BLOCK DIAGRAM — MAIN SECTION —
5050
HCD-RV777D/RV888D/RV999D
HCD-RV777D/RV888D/RV999D
22 KEY0
KEY1
KEY2
LED
X1
X2
VOL A
VOL B
PS07
PS08
PS09
PS10
PS11
PS12
S-OUT
S-IN
S-CLK
RESET
G1-13
S1-21
21
20
34
Q134-139
MASTER CONTROL
IC701 (3/3)
LED
DRIVER
D134-139
(ILLUMINATION)
35
36
37
38
39
3
4
9
8
7
6
V.LOAD 60
44-58,
61-66
67-80
FL1001
FLUORESCENT
INDICATOR
TUBE
10
11
13
45
2
1
100
32
30
29
4
46
21
4
IC921
DVD+12V
REG
M+9V
REG
A+9V
REG
GC+5V
REG
D+4V
REG
AUDIO+5V
REG
D+3.3V
REG
REG
B-REG
RESET
EVER+4V
REG
AU+3.3V AU+5V
31
IC922 D271
D371
D732
RV888D/RV999D
D911
D733
Q971
RELAY
DRIVE
Q901
AC3
F919
F918
F916
F917
F912
F913
F911
AC IN
RY901
AUS,AR,MX,
MODEL
AUS,AR,MX,
MODEL
AUS,AR,MX,
MODEL
AUS,AR,MX,
MODEL
EXCEPT
AUS,AR,MX,
MODEL
EXCEPT AUS,AR,MX,MODEL
EXCEPT
AUS,AR,MX,
MODEL
230-240V
220V
120V
S901
VOLTAGE
SELECTOR
F914
F915
31
IC923
31
IC392
D+1.8V
DVD+12V
M+9V
A+9V
+VH
-VH
+VL
-VL
-VP
GC+5V
AU+5V
D+5V
EVER+4V
D+3.3V
D+4V
D+3.3V
31
IC211
31
IC934
UNREG+20V
UNREG+12V
AC4
VF
31
IC932
31
IC803
21
5
IC805
21
IC804
3
IC901 D902-905
T901
SUB TRANSFORMER
T911
POWER TRANSFORMER
1
5
SWITCH
Q851,852
Q853
Q857
Q855
D192
74
73
I / I
DISPLAY
S11
S12
IR
IC202
REMOTE
CONTROL
RECEIVER
I2C-CLK
I2C-DATA
SYS-RESET
15
87
31
12
18
IN
OUT
OUT
IN
S-CLK
S-OUT
S-IN
SIRCS
POWER KEY
DISPLAY KEY
SYS-RESET
IIC-DATA
IIC-CLK
SUB
CLOCK
SYSTEM
CLOCK
M-RESET
VF
-VP
RESET
ACCUT
STB-RELAY
SYS-POWER
STANDBY
LED
RESET
SWITCH
Q706
IC703
31
X800
32.768kHz
X801
16MHz
15
16
AU+3.3V
REG
D+1.8V
REG
S13-22
FUNCTION
KEY
S31-40
FUNCTION
KEY
S51-60,701
FUNCTION
KEY
S102
MASTER
VOLUME
ENCODER
I / I
DVD DSP
SECTION
C
DISPLAY CONTROL
IC101
X101
5MHz
• Abbreviation
AUS : Australian model
AR : Argentine model
MX : Mexican model
(Page 47)
7-5. BLOCK DIAGRAM — DVD SYS SECTION —
51 51
HCD-RV777D/RV888D/RV999D
HCD-RV777D/RV888D/RV999D
7-7. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
Note on Printed Wiring Board:
•X: parts extracted from the component side.
•Y: parts extracted from the conductor side.
•: Pattern from the side which enables seeing.
(The other layer’s patterns are not indicated.)
Caution:
Pattern face side: Parts on the pattern face side seen from
(Conductor Side) the pattern face are indicated.
Parts face side: Parts on the parts face side seen from
(Component Side) the parts face are indicated.
C
B
These are omitted.
E
Q
B
These are omitted.
CE
Q
B
These are omitted.
CE
Q
Note on Schematic Diagram:
•All capacitors are in µF unless otherwise noted. (p: pF)
50 WV or less are not indicated except for electrolytics
and tantalums.
•All resistors are in Ω and 1/4 W or less unless otherwise
specified.
•2: nonflammable resistor.
•C: panel designation.
•Indication of transistor. •A: B+ Line.
•B: B– Line.
•Voltage and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : FM
∗: Impossible to measure
•Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal produc-
tion tolerances.
•Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal produc-
tion tolerances.
•Circled numbers refer to waveforms.
•Signal path.
F: AUDIO
f: TUNER
L: VIDEO (COMPONENT)
r: VIDEO (COMPOSITE)
E: TAPE PLAY (DECK A)
d: TAPE PLAY (DECK B)
G: TAPE REC (DECK B)
J: DVD (AUDIO)
c: DVD (RF)
I: DVD (DIGITAL)
• Abbreviation
AUS : Australian model
AR : Argentina model
MX : Mexican model
Note: The components identified by mark 0 or dotted line
with mark 0 are critical for safety.
Replace only with part number specified.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
•Unleaded solder melts at a temperature about 40 °C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to about
350 °C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
•Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
•Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may also
be added to ordinary solder.
7-6. CIRCUIT BOARDS LOCATION
SUB TRANS board
JACK board
PANEL board
TRANS board
P-STREAM board
HP board
MAIN board
FRONT AMP board
SIRCS board
DRIVER board
SW board
DMB07 board
RF board
MOTOR (LD) board MOTOR (TB) board
SENSOR board
SURROUND AMP boar
d
(HCD-RV888D/RV999D)
LEAD PIN board
(HCD-RV777D)
VIDEO board
5252
HCD-RV777D/RV888D/RV999D
HCD-RV777D/RV888D/RV999D
7-8. PRINTED WIRING BOARD — DVD MECHANISM SECTION (1/2) — • Refer to page 51 for Circuit Boards Location. : Uses unleaded solder.
(Page 56)
1
A
B
C
D
E
F
234567891011 12 13 14
C023
C028
C040
C037
R004
R005
C038
C022
C020
R016
R003
R018
R014
R012
C027
C041
C010
Q002
Q001
R007
C039
R001
C021
C013
R009
R008
C008
C017
C015
C011
C009
R021
CN003
CN001
CN002
C049
IC003
R033
R034
R047
R046
C050
C052
R091
R024
R025
R023
C029
C026
R026
C024
R027
R017
R015
C042
R013
R019
L002
L001
C003
D002
D001
R022
R020
C031
R011
C006
C005
C034
R006
R028
R029
C036
C032
C035
C033
C004
C012
C025
R010
C002
C030
C018
C016
C014
C019
R035
C001
R041
R031
R032
C051
IC001
Ref. No. Location
D001 C-11
D002 B-11
IC001 E-11
IC003 E-4
Q001 B-4
Q002 B-4
• Semiconductor
Location
53 53
HCD-RV777D/RV888D/RV999D
HCD-RV777D/RV888D/RV999D
7-9. SCHEMATIC DIAGRAM — DVD MECHANISM SECTION (1/2) — • Refer to page 84 for IC Block Diagram.
(Page 59)
IC B/D
(DBU-3)
JL005
C011
C039
C038
R021
JL007
C003 R010R008R007
IOP1
L002
C004D002
R006
C001
C010
R004R003
IOP2
L001
C002D001
R022
R025
R023
C016
C015
C014
R014
R013
R012
R011
R018
R017
R016
R015
C042
C020
C021
C022
C023
R024
C027C028
C029
C018
C017
C019
C024
C031
C033 C012 C005
JL003
JL006
R029
R028
R027
JL002
JL001
C032
C034
C049
C009
C035
CN003
CN001
CN002
C025
C006 C013
R005
R009
R035
R019 R020 C041
Q001 Q002
C008
R041
JL004
C030
C026
R001
R026
R034
R033
R047
IC003
C052
R046
C036
C051
C050
C040 R091
C037
IC001
R031
• Waveforms
– RF Board –
1
2
IC001 1 (DVDRFP)
800mVp-p
3
4
IC001 el (TE)
IC001 r; (FE)
0.3Vp-p
1.3Vp-p
IC001 tj (RFAC)
0.5Vp-p
200mV/DIV, 100ns/DIV
500mV/DIV, 1ms/DIV
100mV/DIV, 1ms/DIV
500mV/DIV, 100ns/DIV
5454
HCD-RV777D/RV888D/RV999D
HCD-RV777D/RV888D/RV999D
7-10. PRINTED WIRING BOARDS — DVD MECHANISM SECTION (2/2) — • Refer to page 51 for Circuit Boards Location. : Uses unleaded solder.
Ref. No. Location
D701 D-6
D711 D-7
IC701 F-6
IC712 F-7
IC731 E-11
Q731 C-9
• Semiconductor
Location
(Page 66)
1
A
B
C
D
E
F
G
H
234567891011121314
(OPEN/CLOSE DETECT)
(DISC TRAY ADDRESS DETECT)
CN751
S751
IC731
CN731
CN741
CN742
C715
C731
C735
C736
R701
R711
R731
R721
R722
R723
R735
R732
R733
R734
D701
D711
Q731
C751
IC712
IC701
CN704
C737
R713
R712
C741
R702
JW702
JW703
JW704
JW705
JW706
JW707
JW708
JW711
CN703
CN702
CN705
R751
C752
CN701
JW712
JW701
JW709
JW710
JW713
JW714
CN721
MAIN
BOARD
CN543
55 55
HCD-RV777D/RV888D/RV999D
HCD-RV777D/RV888D/RV999D
7-11. SCHEMATIC DIAGRAM — DVD MECHANISM SECTION (2/2) — • Refer to page 84 for IC Block Diagrams.
(Page 67)
IC B/D
IC B/D
R751
C752CN705
CN704
CN721
CN751
C751
IC701
IC712
R701
D701
R713
R711
R723 R721R722
C735C736C737
R735
R733 R731
C731
Q731
C741CN702
CN703
CN701
RE701
IC731 CN731 CN741
CN742
CN751
C715
R702
R712
R732R734
D711
M751
M741
S751
5656
HCD-RV777D/RV888D/RV999D
HCD-RV777D/RV888D/RV999D
• Refer to page 51 for Circuit Boards Location.
7-12. PRINTED WIRING BOARD — DMB07 SECTION — • Refer to page 58 for Semiconductor Location. : Uses unleaded solder.
1
A
B
C
D
E
F
G
H
I
234567891011 12 13 14
C343C345
C346
A1
A2
A3
A4
A5
A6
A9
A10
A11
A12
A13
A14
A17
A18
A15
A16
A19
FL703
CN101
R718
R769
C717
R767
C777 C778
C779
C780
R975
CN901
FL702
R908
C733
R765
R764
R763
R762
C702
R250
R215
C705
IC906 IC904
IC902
C706
C708
C711
FL204
C712
R927
R931
C1302
C917
C916
C915
C914
C907
C715
C716
C533
C556
C561
R751
JW801
C588
X902
C771
C773
C774
C701
FL701
IC701
C259
C258
R601
R788
R707
RB202
RB203
RB204
R217
R916
R219
R709
R710
R984
IC232
IC231
R284
R283
R277
R276
R275
R274
R273
R269
R917
R15
R268
R505
R267R266R265R264
R263
R14
R988
R254
R13
R994
R995
R997
R998
R571
R711
R234
R712
R231
R230
C781
R552
R548
C213
C215
C325
C321
C306
R714
C305
C304 C303
C302
D1303
D1304
R1302
R978
R716
IC207
FL205
D202
CN202
CN105
R717
R719
FL206
C502
R964
R907
R906
R905
C552
C201
C517
C518
R921
R922
R923
C522
JW806
L501
R928 R929
JW805
JW802
JW804
JW803
C526
C528
C101
C151
JW392
C531
C534
C535
C543
C544
C545
C548
C551
C553
IC211
C558
C559
C560
C563
C565
C567
C568
C569
C573
C590
FL101
C901
C902
C924
C903
C904
C905
C926
C927
R962
R958
C592
R747
FB105
C202
R748
CN501
D901
FL501
FL502
FL901
IC503
IC509
IC901
C532
R758
L103
R760
R504
C266
C265
R805
C263
R506
R510
R511
R523
C261
R599
R593
C253
C252
R588
R586
R584
R314
C925
C394
C393
C392
C248
R940
R942
R572
R943
R568
R567
C246
R566
R565
R564
R563
R562
IC302
CN102
R561
R560
R559
R558
FL303
FL302
C245
C242
C241
C239
CN107
R970
C227
R551
R550
C214
R545
R536
R938
R936
C547
R213
C279
C278
C277
C291
X901
R708
C283
(Page 70)(Page 70)
(Page 70) (Page 52)
(Page 66)
57 57
HCD-RV777D/RV888D/RV999D
HCD-RV777D/RV888D/RV999D
1
A
B
C
D
E
F
G
H
I
J
234567891011121314
IC206
R320
R288
IC252
R1001
R239
C289
R343
R342
C342 C344
IC331
B1
B2
B3
B4
B5
B6
B8
B9
B10
R367
B7
B11
R218
R577
IC111
R369
R368
IC703
C727
C767
C769
R789
C729
C776
FL706
R799
R777
R776
R778
C703
R271
FL903
C709
FB903
FB902
R932
R933
C713
C714
R301
C516
C524
C718
C720
C721
C722
C723
C724
C725
C726
C728
C730
C740
C741
C742
C743
C744
C745
C752
C760 C761 C762 C763 C764
C765
C766
C768
C770
C772
C775
C782
C783
FL705
R785
R786
IC706
C734
R700
L704
C275
C264
C205
R787
R270
R222
R221
R1000
R220
C540
R282 R281 R280 R279 R278
R261
R260
R514
R515
R259
R257
R255
R522
R253
R251
R527
R248
R247
R246
R245
R244
R990
R241
R240
R996
R12
R11
R10
R232
R227
C326
R713
Q202
C324
C323
C322
R534
R915
C309
C308
C307
R918
R715
C274
IC204
FL203
R720
R721
R724
R725
C501
R726 R727
R974
R728
C928
R730
R731
R732
R733
R734
R735
R736
R737
R738
R913
R912
R911
C508
R904
R902
R901
C509
C510
C511
C507
C512
C514
C515
C276
R741
R920
C519
R925 R926
R930
C506
C504
C503
C525
C527
IC203
C529
D392
R742
C570
R743
C589
C513
R744
R745
C906
C908
C909
C910
C913
C918
R746
IC907
C203
C523
FL908
IC501
IC903
IC392
R750
Q901
D393
D394
R699
R698
R694
R503
C272
C271
C270
C269
C268
C267
R935
C262
R512
R513
R516
R517
R519
R520
R521
R524
R525
C260
R594
C257
C256
C255
C254
R591
R589
R587
R582
R581
R580
R313
R312
R311
R310
R579
R309
R308
R307
R306
R573
C251
C250
C249
C247
R305
R304
R303
R302
R9980
C244
C243
R9981
C240
C238 C237
C236
C235
C234
C233
R9998
R9999
C232
C231
C230
C229
R555
C226
C220
C218
C216
C204
R537
R533
R530
R529
IC233
R272
R290
R292
R291
C290
C280
C281
C282
L901
5858
HCD-RV777D/RV888D/RV999D
HCD-RV777D/RV888D/RV999D
7-13. SCHEMATIC DIAGRAM — DMB07 SECTION (1/8) — • Refer to page 84 for IC Block Diagrams.
(Page 67)
(Page 63)
(Page 61)
(Page 64)
(Page 61, 63, 64)
(Page 61)
IC B/D
IC B/D
R309
C392
CL316
CL317
CL318
CL319
CL320
CL321
CL322
CL323
CL324
CL325
CL327
C326
R305
R304
CL310
CL311
R303
R302
CL309
CL312
R307
R306
CL313
CL315
CL314
C308
C309
JW392
C393
D394D393
R311
R310
R313
R314
FL303
C323
C322
C304
C305
C303
C302
C307
C306
R312
R308
CN107
D392 FL302
C325
R369
R368 CL326
C321
R367
R342
JL304
JL303
C346
C343
C342
C345 C344
IC331
R320
IC302
R1302
C324
C394
IC392
D1303
D1304 C1302
(Page
61, 63, 64)
D202 E-9
(D392) H-3
(D393) H-3
(D394) H-3
D901 G-4
D1303 C-2
D1304 C-2
Ref. No. Location
• Semiconductor Location
Ref. No. Location
(IC111) B-6
(IC203) D-14
(IC204) D-11
(IC206) G-14
IC207 D-12
IC211 E-8
IC231 G-13
( ): SIDE B
IC232 H-14
(IC233) G-13
(IC252) D-8
IC302 D-3
(IC331) F-3
(IC392) H-3
(IC501) G-8
IC503 F-8
IC509 F-8
IC701 G-12
(IC703) F-10
(IC706) G-12
IC901 F-5
IC902 E-11
(IC903) F-6
IC904 E-11
IC906 F-10
(IC907) G-4
(Q202) C-11
(Q901) G-5
Ref. No. Location Ref. No. Location Ref. No. Location
59 59
HCD-RV777D/RV888D/RV999D
HCD-RV777D/RV888D/RV999D
7-14. SCHEMATIC DIAGRAM — DMB07 SECTION (2/8) — • Refer to page 84 for IC Block Diagram.
IC B/D
R562R558
R560
R561
R588
R593
R566
R565
R567
R572
R571
R584
CL536
CL535
CL531
CL530
CL529
CL526
CL525
CL524
CL523
CL537
CL513
CL512
CL515
CL514
CL521
CL520
CL519
CL518
CL505
CL504
CL503
CL502
CL501
CL508
CL507
CL506
CL522
CL527 R550
R551
R552
R559
R563
R564
C588
C589
C590
CL544
CL517
CL516
CL510
CL509
R506
R504
C502
R503
C501
CL511
R573
R599
R555
R536
R537
C568
CN501
R694
C558
R601
CL528
C535
C531
C533
C544
C534
C548
C551
C559
C565
C560
C547
R699
C573
R545
R548
C552
C553
IC509
FL502
FL501
C570
C569
C545
C543
R505
C516
C518
C522
IC503
R591
C507
L501
C513
C540
R577
C567
C517
R698
C592
C511
C515
R568
C561C563 C556
C532 C523
(Page 53)
(Page 61)
(Page 60)
6060
HCD-RV777D/RV888D/RV999D
HCD-RV777D/RV888D/RV999D
7-15. SCHEMATIC DIAGRAM — DMB07 SECTION (3/8) —
R746
R745
C714
C713
C716 C717
C712
C709
C773
C771
R721 C720
R724
R726R725
R720
C715
C706
R767
R765
C774
C775
R732
R737
R735
R758
C721
C766
C752
R728
R727
C728
R799
C703
C702
C780 C779
C727
R738
R736
R734
R733
R716
R717
R713
R712
R711
R709
R764 R763 R769
R750
R778
R742
R744
R731
R730
R777
R776
R748
R747
R700
R788
R789
R715
R785
R786
R751
IC701
C729
C783
C782
C705
R787
FL701
FL702
FL703
FL705
R762
R743
R714
FL706
C708
R708
R707
R710
R719
IC703(2/2)
C781
C711
IC703(1/2)
R594
C764
C763 C762
C761 C760
R741
C744
C745
C742
C743
C730
C740
C741
C725
C726
C724
C765
C769
C768
R760
C770
L704 C734C776
C777 C778
C733
C701
IC706
C772
C767
C718
C722
C723
R718
(Page
59)
(Page 62)
(Page 63)
61 61
HCD-RV777D/RV888D/RV999D
HCD-RV777D/RV888D/RV999D
7-16. SCHEMATIC DIAGRAM — DMB07 SECTION (4/8) —
CN102
CL932
CL931
CL933
CL935
CL937
CL943
CL942
CL941
CL940
CL939
C151
D901
C926
R579
R534
R533C514
R530
R529C512
R527C510
R523
C508R517
R522C509
C506R516
R512
R513
C525
C528
C529
R510
R511
C526
R589
C519
R580
C925
IC501
C527
C504
C503
C927
IC907
R521
R524
R525
R519
R520
C928
CL936
R587
L103
R515
R514
C524
R586
C101
FL101
FB105
R581
R582
(Page 59)
(Page 62)
(Page 58, 63, 64)
(Page 58, 63, 64)
(Page 64)
(Page 58)
(Page 58)
(Page 71)
6
7
IC207 <zz.> (VDAC 4)
8
9
IC207 <zxx> (VDAC 3)
IC207 <zxb> (VDAC 2)
IC207 <zx,> (VDAC 1)
200mV/DIV, 20µs/DIV
200mV/DIV, 20µs/DIV
200mV/DIV, 20µs/DIV
200mV/DIV, 20µs/DIV
q;
IC207 <zcz> (VDAC 0)
500mV/DIV, 20µs/DIV
1.3Vp-p
1.2Vp-p
900mVp-p
H
H
H
H
820mVp-p
H
• Waveforms
– DMB07 Board –
1
2
IC901 r; (XTAL)
3
4
IC906 3 (MO1)
IC906 8 (XTO)
4.5Vp-p
37ns
IC906 q; (SO2)
4.5Vp-p
1V/DIV, 20ns/DIV
1V/DIV, 10ns/DIV
1V/DIV, 10ns/DIV
1V/DIV, 10ns/DIV
5
IC906 qd (SO3)
1V/DIV, 10ns/DIV
5.6Vp-p
4.6Vp-p
3.9Vp-p
29.5ns
50ns
29.5ns
37ns
820mVp-p
6262
HCD-RV777D/RV888D/RV999D
HCD-RV777D/RV888D/RV999D
• Refer to page 61 for Waveforms.
7-17. SCHEMATIC DIAGRAM — DMB07 SECTION (5/8) — • Refer to page 85 for IC Block Diagrams.
IC B/D
IC B/D
C918
R913
CL910
CL909
CL908
CL907
CL906
C924
R970
C902
C901
R958
R918
R901
R902
C906
R978
R905
R906
R907
R911
R912
CL922
R974
R915
C909
C903
C904
R988
R916
R917
R994
R995
R996
R997
R998
R920
R984
R935
R904
R926
R930
C905
C910
R940
R921
R942
X901
R931
R927
X902
C916
C917
L901
R932
R933
CN901
CL954
CL959
CL955
CL950
CL951
CL952
CL953
R908
R975
Q901
R923
FL903
FB902
FB903
IC906
FL908
FL901
R962
R943
R925
C908
C907
R990
C915
C914
R964
R928
R929
R922
R938
C913
R936
IC111
CN101
IC903
IC901
IC902
IC904
(Page 60)
(Page 61)
(Page 71)
(Page 63)
63 63
HCD-RV777D/RV888D/RV999D
HCD-RV777D/RV888D/RV999D
7-18. SCHEMATIC DIAGRAM — DMB07 SECTION (6/8) — • Refer to page 86 for IC Block Diagram.
IC B/D
CN202
CL210
CL209
CL208
CL207
CL206
CL204
R281R280R279R278
R9981
R9998
R9999
R9980
R282
R270
CN105
IC252
R1001
R288
C289 R239
RB202
RB204
RB203
R272
R271
JW801
JW802
JW803
JW805
JW804
JW806
R218
(Page 60)
(Page 62)
(Page 58)
(Page 64)
(Page 58, 61, 64)
(Page 71)
(Page 64)
(Page 58, 61, 64)
6464
HCD-RV777D/RV888D/RV999D
HCD-RV777D/RV888D/RV999D
• Refer to page 61 for Waveforms.
7-19. SCHEMATIC DIAGRAM — DMB07 SECTION (7/8) — • Refer to page 86 for IC Block Diagram.
IC B/D
R213
C213
C215C214
C216
R274
R275
R276
R10
R11
R12
R13
R14
R15
C260
C257
C267
C268
C269
C271
C248
C241
C238C236
C272
C252
C229
C247
C266
C237
R232
R231
R230
C265
R241
R245
R248
R257
R244
R246
R247
R259
R260
R251
JL214
JL213
JL212
JL211
JL210
JL209
JL208
JL207
R263 R264 R265 R266 R267
JL204
JL203
JL217
JL216
JL218
JL202
CL251
CL252
CL253
CL254
CL255
CL256
CL257
R240 Q202
D202
IC211
R805
C226
C204
FL206
FL205
R254
R253
R234
C244
C262
R227
C251
R255
C256
C242
C253
C261
C263
R277
R273
C230 C231 C232 C233 C234
R1000R261
IC204
JL215
R284
R283
JL205
JL206
R222 R221
R220
R219
R269
R217
R268
R290
C291
R291R292
C283 C282
C270
C280
C281
C290
IC207
C277
C278
C276
C274
C279
(Page 58)
(Page 65)
(Page 65)
(Page 61)
(Page 58, 61, 63)
(Page 58, 61, 63)
(Page 63)
(Page 63)
65 65
HCD-RV777D/RV888D/RV999D
HCD-RV777D/RV888D/RV999D
7-20. SCHEMATIC DIAGRAM — DMB07 SECTION (8/8) —
R215
C254
C259
C205
C250
C246
C243
C240
C235
C220
C218
C227
C239
C245
C249
C264
FL203 FL204 C258
C255
R250
R301
IC232 IC231
IC233
C275
C203
C202
C201
IC206
IC203
(Page 64)
(Page 64)
6666
HCD-RV777D/RV888D/RV999D
HCD-RV777D/RV888D/RV999D
1
A
B
C
D
E
F
G
H
I
2345678910111213
B3
B4
B6
R850
IC101
R888
R886
R887
R342
R835
R341
R899
R801
R852
R811
C897
C817
R856
D230
R885
R332
R331
C308
R309
R314
R313
R863
R849
R847
R848
R947
R855
R859
R948
JR13
R312
R311
R310
R320
R321
R323
R322
R351
R132
R352
C814
R364
R363
R657
R972
R362
R806
R361
R360
R359
R357
R356
C309
C306
C714
C305
R862
R658
R861
R860
R803
R857
R870
R778
R858
C657
C333
R868
R869
R867
C815
C352
D813
R832
R875
C330
R854
R974
L341
R874
R872
C323
R871
R804
R900
R873
R973
R807
R805
R833
C811
Q709
R748
R746
R750
C723
R749
C726
C363
D703
D716
D717
Q710
Q708
C332
R753
R754
D735
D734
R747
Q707
C342
C359
R851
C172
R730
R779
R656
C353
C356
R709
R353
C159
C313
C364
C303
R152
R177
R330
C160
R153
C321
C355
C302
C358
Q143
C162
R307
R306
R305
R304
Q183
R303
R302
R301
IC301 R354
R355
C101
R802
R172
R155
R930
R156
D194
R154
R686
D709
R101
C562
R102
Q152
C713
JR104
FB561
R133
R134
R114
R174
R115
D231
Q112
JR105
R116
R371
C122
C120
R113
C118
C119
R112
R173
R616 C617
R617
R175
R185
D611
C143
R196
R618
R197
D193
R620
Q182
R147
R661
C661
R831
C662
C182
C663
R662
R663
IC203
R149
R144
R187
C183
R148
R189
C142
R145
R186
R188
R131
R184
D171
R111
R151
R130
R146
R375
C347
R834
Q723
R613
R171
R117
R118
R119
R120
R668
R653
R654
R655
R615
R157
R158
R159
R160
R614
C235
R271
R693
R625
R626
R622
R623
R624
R621
R627
R628
R629
D708
R694
R808
R677
R601
C601
C602
R602
Q602
Q603
R603
R604
R639
R180
R682
R372
R664
R665Q662
R666
R667
Q661
R377
D812
D201
R813
R711
JR15
R780
Q377
Q374
R397
R894
R994 R893
R993
R895
C899
D811
D810
D809
R760
R563
C863
R708
R710
FB801
R726
R706
Q703
Q721
Q714
JR16
D704
R679
R684
R680
R688
R678
D609
R902
D712
R685
D707
Q705
D706
JR17
D610
R707
R755
R681
R683
D705
R743
Q613
R768
Q618
R762
R687
R761
R676 R675
Q724
Q615
Q702
R767
Q801
R140
Q701
Q616
R853
Q614
Q704
Q706
R736
R744
R766
Q617
R142
R745
R727
C724
R830
R729
R764
R176
R230
C821
R901
R829
R929
D710
D804
R809
D202
D711
R975
R231
JR3
R896
Q719
R776
R774
R777
R897
Q142
C314
JR6
R233
R381
R382R387
R388
R178
R179
Q171 Q172
R191
R192
R193
R194
C158
JR5
R812
C813
C810
JR4
R826
R836
R817 R818
R819
R820
R821
R822
R823
R824
R825
JR9
R394
R395
R393
R182
Q375
Q373
R141
R384
R385
R383
R386
R374
R373
R376
R181
JR8
IC303
JR11
JR12
JR10
Q605
R605
Q606
Q111
Q151
Q621
Q622
Q623
Q624
Q625
Q626
Q627
Q628
Q629
Q630Q631
JR110
Q607
Q608
R607
R608
C611
C651
C613
C653
JR14
Q191
Q232
Q233
Q234
R669
Q604
R609
R610
JR601
JR602
JR603
D101
D102
IC701
C621
C622
C623
C624
R611
R612
R651
R652
D192
R195
FB899
FB862
C202
C201
LP801
W102
W103
JW111
JW112
JW113
JW114
JW115
JW116
JW117
JW119
JW120
JW121
JW122
JW123
JW124
JW125
JW126
JW127
JW129
JW130
JW131
JW132
JW134
JW135
JW136
JW137
JW138
JW139
JW140
JW141
JW142
JW146
JW147
JW148
JW155
JW156JW159
JW160
JW163
JW164
JW165
JW166
JW167
JW168
JW169
JW170
JW171
JW173
JW175
JW176
JW178
JW180
JW181
JW182
JW183
JW184
JW185
JW186
JW187
JW188
JW191
JW196
JW200
JW201
JW202
JW204
JW205
JW206
JW207
JW208
JW209
JW210
JW212
JW213
JW214
JW215
JW216
JW217
JW218
JW219
JW220
JW224
JW225
JW226
JW228
JW229
JW230
JW231
JW232
JW233
JW234
JW235
JW236
JW237
JW240
JW241
JW242
JW243
JW244
JW245
JW246
JW247
JW248
JW249
JW250
JW251
JW252
JW253
JW254
JW255
JW259
JW260
JW261
JW262
JW263 JW264
JW265
JW266
JW268
JW269
JW270
JW271
JW272
JW273
JW274
JW275
JW276
JW277
JW278
JW279
JW280
JW281
JW282
JW283
JW284
JW285
JW286
JW287
JW288
JW289
JW290
JW293
JW296
JW307
JW310
JW311
JW312
JW313
JW314 JW315
JW316
JW317
JW318
JW328
JW329
JW330
JW331
JW337
JW338
JW339
JW340
JW341
JW342
JW343
JW344
JW345
JW350
JW351
JW352
JW354
JW355
JW356
JW357
JW360
JW361
JW362
JW365
JW366
JW367
JW368
JW369
JW370
JW371
JW372
JW373
JW376
JW377
JW378
JW379
JW380
JW381
JW382
JW383
JW384
JW385
JW386
JW387
JW388
JW389
JW390
JW391
JW392
JW393
JW394
JW395
JW396
JW397
JW398
JW399
JW400
JW401
JW403
JW404
JW405
JW408
JW411
JW412
JW414
JW415
JW416
JW421
JW422 JW423
JW424
JW425
JW426
JW427
JW428
JW434
JW435
JW436
JW437
JW438
JW439
JW440
JW441
LP803
LP804
JW442
JW149
JW151
JW150
JW154
JW157
JW158
JW152
JW153
JW258
JW174 JW194
JW179
CN705
C372
CN704
CN603
J102
CN707
CN605
CN602
C165
X800
C233
X801
C862
C898
C735
C331
C351
C322
C659
C320
CN543
C658
C325
C324
C334
C341
C345
C344
C343
C337
C719
Q713
D733
D732
C772
C753
C752
C734
C740
C739
C365
C361
C360
C357
C354
C367
C338
C312
C311
C310
C307
C161
C304
C301
JW102
C368
C163
IC302
C102
C132
C134
C133
C124
C125
C123
C121
C193
C618
C619
C191
C192
C117
C620
C135
C136
L561
C563
C153 C154
C155
C156
C152
C137
C157
C115
J104
C126
C113 C112
C171
C111
C127
C655
C656
C103 C104 C105
C151
C167
C166
C616
C615
C612
C652
EPT701
C145
C603
Q601
C604
C664
CN102
C665
JW103
JW107
CN801
T601
C605
C774
R150
CN706
CN901
C791
D729
C773
IC703
C775
D714
CN301
C715
C185
R190
C164
C272
C371 C271
C231
C232
C114
C816
C335
C666
JW108
JW106
JW334
JW211
JW199
JW407
JW406
JW402
JW105
JW448
JW298
JW349
JW348
JW353
JW238
JW319
JW320
JW321
JW322
JW333
JW358
JW359
JW445
JW301
JW302
JW303
JW306
JW305
JW304
JW101
JW346
JW347
JW363
JW364
JW309
JW335
JW325
JW326
C738
JW197
JW143
JW144
JW145
JW297
JW294
JW292
JW291
JW295
JW223
JW300
JW299
JW221
C614
C654
JW267
LP805
JW418
JW413
JW431 JW432
JW433
JW409
JW417
JW336
JW323
JW324
NO805
NO708
NO503
CN902
JW128
JW161
JW256
JW257
JW177
JW195
JW227
JW374
JW419
JW420
JW430
JW458
JW459
C234
JW460
JW327
JW449
JW450
JW451
JW452
JW453
JW454
JW455
JW456
JW118
C607
JW193
JW192
JW190
JW189
JW447
JW222
JW172
JW239
JW429
LP802
JW444
JW446
JW198
JW203
JW308
C181
C141
JW375
JW410
7-21. PRINTED WIRING BOARD — MAIN SECTION — • Refer to page 51 for Circuit Boards Location. : Uses unleaded solder.
(Page 56)
(Page 54)
(Page 76)
(Page 72) (Page 72) (Page 80)
(Page 78)
(Page 70)
(Page 78)
(Page 74)
D101 C-10
D102 C-10
D171 F-10
D192 C-4
D193 C-4
D194 D-5
D201 F-9
D202 F-9
D230 G-8
D231 G-8
D609 I-3
D610 I-3
D611 H-3
D703 I-10
D704 F-5
D705 E-5
D706 F-5
D707 F-5
D708 H-5
D709 H-6
D710 H-6
D711 H-5
D712 H-4
D714 H-5
D716 I-11
D717 I-11
D729 I-6
D732 G-9
D733 G-9
D734 G-8
D735 G-8
D804 H-6
D809 F-6
D810 D-2
D811 G-6
D812 E-3
D813 G-6
IC101 C-9
IC203 H-7
IC301 C-3
IC302 B-12
IC303 C-4
IC701 G-4
IC703 E-4
Q111 C-8
Q112 D-10
Q142 E-11
Q143 F-11
Q151 B-8
Q152 C-11
Q171 I-8
Q172 I-8
Ref. No. Location
• Semiconductor Location
Ref. No. Location
Q182 E-11
Q183 F-11
Q191 C-5
Q232 H-8
Q233 H-8
Q234 H-8
Q373 C-2
Q374 C-3
Q375 C-3
Q377 F-11
Q601 D-7
Q602 D-6
Q603 D-6
Q604 D-8
Q605 E-7
Q606 E-7
Q607 F-7
Q608 F-7
Q613 H-3
Q614 I-3
Q615 H-3
Q616 H-3
Q617 I-3
Q618 I-3
Q621 C-7
Q622 C-7
Q623 C-6
Q624 D-6
Q625 C-6
Q626 C-6
Q627 C-7
Q628 C-6
Q629 C-6
Q630 D-6
Q631 D-6
Q661 D-7
Q662 D-7
Q701 F-6
Q702 G-6
Q703 F-6
Q704 F-7
Q705 F-7
Q706 F-5
Q707 H-4
Q708 I-11
Q709 I-11
Q710 I-11
Q713 H-12
Q714 I-11
Q719 F-3
Q721 G-6
Q723 F-7
Q724 E-3
Q801 I-5
67 67
HCD-RV777D/RV888D/RV999D
HCD-RV777D/RV888D/RV999D
7-22. SCHEMATIC DIAGRAM — MAIN SECTION (1/3) —
Q142
Q182
R352
C351
R351
R307
R357
C325
C324
C343
R303
C360
R361
R311
R330
R314
R372
R371
R387
R388
R383
R384
R385
R373
R374
R375
R146
R186
R176
R177
TP447
TP446
TP445
TP444
TP443
TP442
TP441
D202
D201
TP430
TP429
TP435
TP438
TP437
TP436
R776R774
R764
R762R760
R761
R768
R766
R767
Q143
C367
R777
R778
R779
R780
Q705
R708R706
R707
D712
CN102
R386
C335
R323
C312
C331
C334
C172
R175R174
D171R172
D811
D810
R150
R140
R180
D812
C201
D813
R727
R729
R709
R710 R726
D809
JR10
C347
CN543 C352
C342
CN901
Q704
Q703
C773
C774
NO503
C145
CN902
C333
R332
R331 C332
C364
C363
C314
C313
JR4 JR5
C330
C344 C345
R313
R312
C311
R309
R310
C361
C337C338
R364
C308
C302
R360
R359
C358
R302
C305
R306
R305
C304
C353
R304
C306
C354
C355
R356
R355
R322
C323
R341
R342
C341
C321
R321
C356
C322
JR110
R395
R394
R393
JR15
JR3
C562 C563
NO805
R190C185
Q183
C202R189
C183
C143 R148
R188
R185 C182
C142R145
R397
R376
R173R171
C171
R149
R184
R144
R147
R187
Q721
Q719
Q724
Q723
Q702
Q701
Q707
C359
C320
C357
C368
C307
R353
Q377
TM901
J104
L561
C775
J102
IC302
FB561
C371
C271
C272
C372
R271 R381
R377 R382
C309
L341
Q374
Q375
Q373
IC301
JW101
CN301
JW103
IC303
JW442
JW102
R354 R320
C772
R301
C301
C303
R362
R363
C365
C310
(Page
58)
(Page 79)
(Page 79)
(Page 71)
(Page 69)
(Page 68)
(Page 75)
(Page 55)
• Waveforms
– MAIN Board –
1
IC701 q;
1.2Vp-p
32.768kHz
2
IC701 qd
0.6Vp-p
16MHz
6868
HCD-RV777D/RV888D/RV999D
HCD-RV777D/RV888D/RV999D
7-23. SCHEMATIC DIAGRAM — MAIN SECTION (2/3) —
C112
C152
C123
C163
R115
R114
R116
R155
R154
R156
R101
R102
C121
C157
R131
Q602
Q603
R639
R602 Q662
Q661
R664 R665
C155
C115
C105
C104
R615 C166
R655
C126
R158
R160
R153
R112
R113
R133
R134
C132
R620
R617
R132
TP101
TP100
C103
C113
C153
C156
C137
Q625
Q626
Q627
Q628
Q629
Q624
R621
R622
R605
R607R608
LP805
LP803
LP801
LP804
C607
R611
R651
R652
R612
LP802
C120
C122
C102
C162
C154
C114
R656
C657
C617
C656
C160
C159
C158
C118
C119
C135
C662
C663
C620
R618
C136
C659
R657
C612
C652
C654
C614
R623
R624
R626
R625
R627 R628 R629
Q630
Q631
Q623
JR601
JR602
JR603
CN602
CN603
Q606
Q605
Q608
Q607
C124
C125
C165
C164
JR104
D101
D102
C101
C134
C111
R661
R669
C661
R662
R668
R663
C666
R130 R658
C161
C658
R152
C151
R159
R157
R119
R117
R118
C615
C621
C622
R613
C616 R614
C623
C624
R653
R120
R654
C127
C655
C653
C613
Q622
Q621
C604
R601
C602
C601
C603
C605
R604
R603
C611
C651
R666
R667
C665
R693
R694
R610R609
C664
Q151 Q152
Q112
T601
Q601
Q604
C167
JR105
C618
R616
C619
C117
Q111
IC101
JW107
C133
R111
R151
R151
R111
(Page 69)
(Page 67)
69 69
HCD-RV777D/RV888D/RV999D
HCD-RV777D/RV888D/RV999D
7-24. SCHEMATIC DIAGRAM — MAIN SECTION (3/3) — • Refer to page 67 for Waveforms.
Q613 Q617Q616
R801
R802
R803
R804
R805
R807
R809
R826
R822
R823
R824
R829
R830
R930R929 D804
R825
C816
R831
R832
R833
R888
R887
R886
R885
R870
R869
R868
R867
R875
R856
R855
R854
R853
R852
R851
R730
D704 R736
R743
C715 D707
R744
C897
D710
D708
D709
D711
CN801
R993
C740
C738
TP707
D733
D732
D735
D734
TP705 R750
R746
R747
C724
Q713
Q710 C723
R749
R808
R834
C726
R857
R806
R836
R897
R835
R896
R902
R895
R899
R813
C231
C232 C235
IC203
R191
R192
R193
R194
C192
C191
D192
R195
D193
R197 C193
D194R196
R142
R182
JW108
TP63
TP94
TP95
C234
R684
R683
R688
R687
R686
R685
C713
C714
R745
D706D705
FB899
R682
R681
R675
R678
R679
R676
R677
R755
C739
R753 R754
D703 Q709
R748
R680
D729
C791
C821
R563
Q171Q172
R711
R230
D230
D231 R231
Q232
Q234
Q233
R233
R948
R947
R871
CN605
Q614 Q615 Q618
CN706
C752
C753
C734
C735
Q708
Q714
NO708
CN707
CN705
CN704
R850
R849
R848
R847
JR14
JR8
R975
R900
C899
C898
R817
R819
R821
R820
R818
C810
C811
R811
R812
C817
IC703
C862
C863
FB862 R863
R862
R859
R872
R873
R874
R974 R973 R972
C814C815
R861
R860
R858
JR6
C141
C181
R141
R181
D714
R901
D609 D611 D610
C813
Q191
Q801
C719
FAN901
JR17
JR16
EPT701
R179
R893
R894
R994
JR13 JR12
JR11
IC701
X801
X800
FB801
Q706
D716
D717
R178
JR9
C233
(Page
68)
(Page 77)
(Page 67)
(Page 73)
(Page 73)
(Page 81)
7070
HCD-RV777D/RV888D/RV999D
HCD-RV777D/RV888D/RV999D
1
A
B
C
D
E
F
G
H
I
234567891011 12 13 14
IC802
IC801
JW590
JW501
D861
IC803
JW853
Q857
R871
D871
FB872
C809
FB830
C833
C802
C813
C806
C814
FB824
FB818
FB821
R836
FB833
FB834
R833
C816
R824
R818
FB827
L800
Q852
EP801
C812
R821
C804
C801
D838
R803
R838
IC804
Q853
C838
C836
R839
R837
C839
EP802
J801
R851
C841
C808
C807
R815
IC805
R830
R861
FB862
C852
C851
C840
JW801
JW806
JW814
C815
C810
NO803
C862
C872
C863
C873
C860
JW812
JW809
JW818
JW817
C861
C871
JW805
JW803
JW858
JW802
JW810
JW813
C811
JW816
R827
Q855
JW819
JW821
L862
L872
C876
JW822
JW808
C877
C800
L871
L861
FB835
C827
C830
C824
C805
CN804
JW804
JW860
CN801
R834
JW811
R835
CN805
C818
C821
R850
R831
JW820
JW807
JW823
J803
J802
CN802
JW861
JW815
Q851
LP801
C837
R840
7-25. PRINTED WIRING BOARD — VIDEO SECTION — • Refer to page 51 for Circuit Boards Location. : Uses unleaded solder.
(Page 56)
(Page 66)
(Page 78) (Page 56)
(Page 56)
Ref. No. Location
D838 D-10
D861 G-6
D871 E-6
IC801 G-9
IC802 C-10
IC803 H-7
IC804 G-7
IC805 F-7
Q851 H-6
Q852 G-5
Q853 C-6
Q855 C-6
Q857 C-6
• Semiconductor
Location
71 71
HCD-RV777D/RV888D/RV999D
HCD-RV777D/RV888D/RV999D
7-26. SCHEMATIC DIAGRAM — VIDEO SECTION — • Refer to page 86 for IC Block Diagram.
IC B/D
IC803
L800
C801
C808
C833
R815
R835
D838
C851
C800
C807
C840
C860
C863
C873
C871
C862
C872
C876 C877
L872
C852
R851 R850
L861
L871
L862
NO803
Q857
Q853
Q851
Q852
C806
C804
C802
C812
C814
C816
R803
C818
C821
C830
C824
C827
R831
R834
R818
R821
R824
R827
R833
R839
D861
D871
CN805
C805
C813 C811
C810
C809
Q855
EP802
CN802
IC801
CN801
EP801
J803
CN804
JW858
IC804
IC805
C861
JW853
FB835
C837 R837
R836
R840
C836
IC802
C838 C839
R838
C841
J802
J801FB818
FB821
FB824
FB827
FB830
FB833
FB834
R861
FB862
C815
R871
FB872
R830
(Page 62)
(Page 61)
(Page 63)
(Page 79)
(Page 67)
7272
HCD-RV777D/RV888D/RV999D
HCD-RV777D/RV888D/RV999D
1
A
B
C
D
E
F
234567891011 12 13 14
TH201
C201
R217
R218
R215
R272
CN206
C934
C938
C933
C937 IC921
C925
Q251
Q222
D251
R222
R260
C202
IC923
C216
R210
C257
C207
C206
R208
R283
R252
R202
R201
R251
R254
R258
R221
R224
R223
Q221
IC934
C283
C221
IC932
C922
R259
C924
D281
C252
C923
R924
C926 C921
IC922
R211
R290
Q282
R280
C281
C256
C282
C284
L281
R284
R281
CN201
R282
Q201
TM201
LP201
LP202
L282
R287
Q281
C203
RY281
R288
IC201
R206
R205
R256
R255
R289
R253
R216
R203
R209
D201
R257
R219
R220
R239
R204
R285
R286
C285
C286
C271
C272
JW203
JW206
JW207
JW208
JW209
JW215
JW222
JW223
JW224
JW226
JW227
JW228
JW229
JW230
JW231
JW236
JW237
JW239
JW240
JW258
JW249
NO251
R207
JW272
R226
R225
JW275
NO271
JW276
Q217
Q216
JW210
R261
JW261
JW260
JW250
JW252
JW253
JW264
JW265
JW267
JW221
JW220
JW219
JW212
JW214 JW213
JW216
JW933
JW201
C251
NO272
R271
D291
JW263
D271
C273
C274
JW202
C253
JW245
JW244
JW243
JW200
C254
C204
C258
C208
EP201
JW247
JW235
JW234
JW233
JW232
JW205
R240
JW248
JW273
JW255
JW254
JW256
JW257
JW241
JW242
JW238
R213
R214
7-27. PRINTED WIRING BOARD — FRONT AMP SECTION — • Refer to page 51 for Circuit Boards Location. : Uses unleaded solder.
(Page 80)
(Page 74) (Page 66) (Page 66)
(Page 74)
Ref. No. Location
D201 D-9
D251 C-8
D271 D-3
D281 C-11
D291 D-11
IC201 F-9
IC921 F-6
IC922 F-6
IC923 F-5
IC932 F-3
IC934 F-4
Q201 D-10
Q216 E-11
Q217 E-11
Q221 E-5
Q222 D-5
Q251 C-9
Q281 B-11
Q282 B-12
• Semiconductor
Location
73 73
HCD-RV777D/RV888D/RV999D
HCD-RV777D/RV888D/RV999D
7-28. SCHEMATIC DIAGRAM — FRONT AMP SECTION —
C281
C282
C283
C284
IC921
IC934
Q282
C201
C251
IC922
IC923
R924
C216
R201
R207
R251
R221
R226 R223
R224
R287
R289
R290
R208
R258
R222
R202
R204
R239
R252
R254
R285
R286
R288
R240
R225
R209
R259
R271
R272
R210
R260
R283 R284
D281
D291
IC932
L281
L282
TM201
Q217
R215
R216
R217
C273
C274
R205
R206
R218
R213
R214
C202
C252
C221
C934 C933
C937C938
C926 C925
C923C924
C921C922
CN206
R211
R261
R220
R219
C253
C203
C207
C206
C257
C256
R256
R255
R257
CN201
NO271
C286
C285
D251
RY281
EP201
NO272
NO251
D201
R282
D271
JW933
IC201
R203
C204
C254
R253
Q201
Q251
Q221
Q222
TH201 C271
C272
Q281 R280
R281
C208
C258
Q216
(Page 75)
(Page 81)
(Page 75)
(Page 69)
(Page 69)
7474
HCD-RV777D/RV888D/RV999D
HCD-RV777D/RV888D/RV999D
1
A
B
C
D
E
F
G
H
I
234567891011 12 13 14
TM401
R353
IC301
JW303
JW304
JW306
JW307
JW312
JW313
JW314
JW324
JW302
NO371
RY381
JW310
L383
L382
L381
R399
R391
R386
R381
R382
LP303
C383
C386
C381
C384
C306
C382
D382
R310
C311
R396
R320
R394
Q351
Q341
R308
D351
R374
R390
R397
C347
R332
R333
Q384
C385
C372
Q383
R345
R311
R355
R373
R383
R360
R305
R385
C357
C346
C303
C353
C342
C352
C371
R309
C307
D381
C351
C354
D301
C302
R395
R321
C344
EP301
R349
C312
D341
EP302
Q316
D491
Q301
R302
R354
R304
R301
R358
R359
R342
R348
R344
R347
R316
R341 R351
R352
R307
C356
C304
C341
D391
Q317
R317
R318
R315
C374
R350
C310
Q381
RY382
C301
D371
LP302
R357
R331
NO300
C343
C308
TH301
R398
CN302 LP301
JW316
JW317
JW318
JW320
JW323
JW329
JW333
R319
CN372
JW327
JW326
JW328
C373
JW330
JW325
JW331
JW332
JW321
JW308
JW319
JW340
JW311
JW309
R303
R343
R314
EP901
LP902 LP901
7-29. PRINTED WIRING BOARDS — SURROUND AMP SECTION (HCD-RV888D/RV999D) — • Refer to page 51 for Circuit Boards Location. : Uses unleaded solder.
(Page 80) (Page 72) (Page 66) (Page 72)
Ref. No. Location
D301 C-9
D341 C-6
D351 C-8
D371 C-3
D381 E-11
D382 B-11
D391 C-5
D491 C-5
IC301 A-9
Q301 C-9
Q316 B-5
Q317 B-5
Q341 C-6
Q351 C-8
Q381 E-9
Q383 E-10
Q384 E-8
• Semiconductor
Location
75 75
HCD-RV777D/RV888D/RV999D
HCD-RV777D/RV888D/RV999D
7-30. SCHEMATIC DIAGRAM — SURROUND AMP SECTION (HCD-RV888D/RV999D) —
C306
C307
C346
C347
C356
C357
C301
C351
C343
C353
R301
R307
R341
R347
R351
R397
R390
R395
R308
R348
R358
R315
R396
R302
R304
R342
R344
R352
R309
R316
R317
R349
R359
R310
R350
R360
D301
D341
D351
D381
D382
D391
D491
R398
C341
L381
L382
L383
Q317
Q381
Q383
R305
R345
R355
R319
C310
C312
C371
C372
R373
R374
C373
C374
TM401
C302
C342
C352
R333
R332
R331
IC301
Q301
Q316
Q341
Q351
R314
R318
R321
R311
C308
R357
NO300
C382
C381
R391R385
C383
C384C386
C385
R386
CN372
NO371
CN302
C303
R354
C311
EP301
D371
RY381
RY382
R320
Q384
TH301
R303
C304
C354
R353
R343
C344
R381
R382
R383
R394
R399
(Page 73)
(Page 81)
(Page 73)
(Page 67)
7676
HCD-RV777D/RV888D/RV999D
HCD-RV777D/RV888D/RV999D
7-31. PRINTED WIRING BOARDS — PANEL SECTION — • Refer to page 51 for Circuit Boards Location. : Uses unleaded solder.
(Page 66)
1
A
B
C
D
E
F
G
234567891011 12 13 14
B2
R11
R12
R13
R14
R15
R16
R17
R18 R19
R20
R31
R32
R33
R34
R35
R36
R37
R38
R39
R40
R51
R52
R53
R54
R55 R56
R57
R58
R59
R60
R61
Q134
Q135
Q136
Q137
Q138
Q139
R123
R124R125
C126
R116
R115
R118
R117
C106
C107
C108
C109
R106
R107
R108
R109
C102
R105
C161
R205
R206
C207
C208
FB101
FB102
R140
R141
R145
R144
R143
R142
R150
R149
R148
R147
R146
R160
R159
R158
R156
R155
R157
R154
R153
R152
R168
R169
R170
R171
R167
R166
R165
R161
R162
R163
C345
C344
R173
R172
R151
R164 C343
C342
C341
C340
C339
C338
C337
C336
C335
C334
C333
R127R128
R129R130
R131R132
R133R134
R135R136
R137R138
IC101
JW110
JW111
JW112
JW113
JW114
JW115
JW116
JW117
JW118
JW119
JW120JW121
JW122
JW123
JW124
JW125
JW126
JW127
JW128
JW129
JW130
JW131
JW132
JW133
JW134
JW135
JW137
JW138
JW139
JW140
JW141
JW142
JW143
JW144
JW145
JW146
JW147
JW148
JW150
JW152
JW153
JW154
JW155
JW156
JW157
JW158
JW159
JW160
JW161
JW162
JW163
JW164
JW165
JW166
JW167
JW168
JW136
S11
S12
S31
S32
S33
S34
S35
S37
S38
S36
S39
S40
S57
S58
S59
S60
S14
S15
S16
S17
S51
S53
S21
S54
S20
S19
S55
S56
S13
S52
S22
S18
CN101
CN103
D192
C125
C101
C160
C206
CN2CN104
X101
JW149
C121
C122
FL1001
C205
CN113 IC202
R62
R119
R120
S102
D134
D135
D136
D137
D138
D139
S701
NO806
NO807
MAIN
BOARD
CN706
Ref. No. Location
D134 F-13
D135 F-14
D136 E-13
D137 E-13
D138 F-12
D139 F-13
D192 B-11
IC101 C-6
IC202 C-13
Q134 E-5
Q135 E-5
Q136 E-5
Q137 F-5
Q138 F-5
Q139 F-5
• Semiconductor
Location
• Waveform
– PANEL Board –
1
IC101 3 (X1)
1.3Vp-p
5MHz
77 77
HCD-RV777D/RV888D/RV999D
HCD-RV777D/RV888D/RV999D
7-32. SCHEMATIC DIAGRAM — PANEL SECTION — • Refer to page 76 for Waveform.
R109
R106
R11R12R13R14R15R16R17R18R19R20
R31
R32R33R34R35R36R37R38R39R40
R51
R52R53R54R55R56R57R58R59R60R61
R107
R108
CN113
CN103
R123
R124
R125
R115
R116
Q134 Q135 Q136
Q137 Q138 Q139
C125
C126
C160
C161
TP41
C102
R206
C101
C207 C208
FB101
FB102
S11 S12
S60
C205
R120
R119
C206
R156
S102
R205
D137
D136
D138
D135
D139
D134
CN101
CN104
NO806
CN2NO807
R62
R117
R118
C106
C107
C108
C109
R127
R128
R129
R130
R131
R132
R133
R134
R135
R136
R137
R138
R140
R142
R143
R141
R146
R145
R144
R148
R149
R147
R152
R153
R151
R150
R155
R154
C335
C334
C333
C336
C337
C342
C345
C344
C343
C341
C340
C339
C338
R158
R157
R173
R172
R171
R170
R169
R168
R167
R163
R166
R162
R161
R164
R165
R160
R159
R105
D192
IC202
S701
S59 S58 S57
S40 S39 S38 S37 S36
S56
S35
S55
S34
S54
S33
S53
S32
S52
S31
S51
S22 S21 S20 S19 S18 S17 S16 S15 S14 S13
X101
IC101
C121
C122
FL1001
(Page 69)
7878
HCD-RV777D/RV888D/RV999D
HCD-RV777D/RV888D/RV999D
7-33. PRINTED WIRING BOARDS — JACK SECTION — • Refer to page 51 for Circuit Boards Location. : Uses unleaded solder.
1
A
B
C
D
E
F
G
H
I
234567891011 12 13 14
C529
D1201
D506
D505
D502
D501 D507
C535
C530
C523
C524
C517
C516
C513
C512
C511
C509
C508
C504
C503
C502
C501
R529
R528
R527
R526
R525
R524
R523
R522
R521
R520
R519
R518 R517
R516
R515
R514
R513
R512
R511
R510
R509
R508
R507
R506
R505
R504 R503
R502 R501
IC501
C507
D508
FB505
C528
C525
C531
IC502
JW508
JW509
JW510
EP501
C521
C527
C533
C522
C534
C526
C536
C514
C518
C532
C519
C520
C510
JW502
FB501
EPT501
EPT502
RV502 RV501
J503 J501
JW507
C515
JW501
JW506
JW500
NO501
NO502
C500
EP502
FB503
FB504
R531
R532
J502
CN503
(Page 66)
(Page 70)
Ref. No. Location
D501 E-10
D502 E-10
D505 E-7
D506 E-7
D507 E-10
D508 E-10
D1201 C-6
IC501 C-9
IC502 C-3
• Semiconductor
Location
(Page 66)
79 79
HCD-RV777D/RV888D/RV999D
HCD-RV777D/RV888D/RV999D
7-34. SCHEMATIC DIAGRAM — JACK SECTION —
C517
R513
R514
RV501
C515
R512
R516
C514 IC501(1/2)
R510
C513
R507 C510
D1201
R529
R528
R524
J501
J503
C518C519
R525
R526 R527
C536
RV502
C534
TP501
TP502
R531
R532
NO502
NO501
C525
CN503
C503R505
R501
C501 FB505 R503
R504C502R502
C504
D502D501
C507
D507
D508
R522
C528
R523
C529
C530
C535
R518 C520
R517
R515
IC501(2/2)
C516
R511
R509
C521
C512
R506
C509 D505
C508D506
C500
C532
C533
C523
R520R521
C527 C526
C524
C522
R519
C531
C511
R508
JW502
EPT501
EPT502
EP503
EP502
J502
IC502
FB501
EP501
FB504 FB503
(Page 67)
(Page 71)
(Page 67)
8080
HCD-RV777D/RV888D/RV999D
HCD-RV777D/RV888D/RV999D
7-35. PRINTED WIRING BOARD — TRANS SECTION — • Refer to page 51 for Circuit Boards Location. : Uses unleaded solder.
(Page 82)
(Page 66)
(Page 72)
(Page 74)
(Page 82)
1
A
B
C
D
E
F
G
234567891011 12 13 14
FH927
FH925
FH919
FH917
FH921
FH923
FH924
FH922
FH918
FH920
FH926
FH928
JW960
JW957
JW954
JW956
JW923
JW955
C915
EP902
CN915
R915
D913
R916
R914
C913
D912
C912
D911
R911
F919
F918
F915
F914
F916
F917
CN913
EP903
C918
R938
LP901
LP902
JW972
LP904
CN914
JW924
Q971
NO912
NO911
Ref. No. Location
D911 B-7
D912 B-5
D913 B-4
Q971 B-4
• Semiconductor
Location
81 81
HCD-RV777D/RV888D/RV999D
HCD-RV777D/RV888D/RV999D
7-36. SCHEMATIC DIAGRAM — TRANS SECTION —
F918
C918
C912
C913
R914
R938
JW972
C915
CN914
CN915 FH918 FH917
FH921FH922
FH924 FH923
FH920 FH919
FH925FH926
FH928 FH927
JW924
R911
JW923
NO912
CN913
Q971
T911
EP902
F916
F914
F915
F917
F919
D913
R915 R916
D912
D911
NO911
(Page 75)
(Page 73)
(Page 69)
(Page 83)
(Page 83)
8282
HCD-RV777D/RV888D/RV999D
HCD-RV777D/RV888D/RV999D
7-37. PRINTED WIRING BOARD — SUB TRANS SECTION — • Refer to page 51 for Circuit Boards Location. : Uses unleaded solder.
1
A
B
C
D
E
F
G
H
I
234567891011 12 13 14
JW901
S901
CN902
JW909
FH911FH912
JW906
JW902
JW910
T901
FH914 FH913
JW907
JW905
CN903
EP901
LP903
FH915
FH916
C903
F913
F912
F911
IC901
Q901
D905
D903 D902
D904
CN901
C901
D901
RY901
C902
R901
R904
JW930
W602
JW903
(Page 80)
(Page 80)
Ref. No. Location
D901 F-2
D902 C-3
D903 D-3
D904 C-3
D905 D-3
IC901 F-2
Q901 F-3
• Semiconductor
Location
83 83
HCD-RV777D/RV888D/RV999D
HCD-RV777D/RV888D/RV999D
7-38. SCHEMATIC DIAGRAM — SUB TRANS SECTION —
(RV888D : AUS / RV999D : AUS,AR)
(RV888D : EXCET AUS / RV999D : EXCEPT AUS,AR)
CN901
C903
FH916 FH915
F913
C902
C901
IC901
R901
R904
FH914 FH913
FH911FH912
CN903
JW909
JW905
JW901JW902
JW903
JW906
JW907
D901
S901
RY901
T901
Q901
CN902
F911
F912
D902
D904
D903
D905
(Page 81)
(Page 81)
8484
HCD-RV777D/RV888D/RV999D
HCD-RV777D/RV888D/RV999D
IC001 SP3723CAFOPM (RF Board)
7-39. IC BLOCK DIAGRAMS
MUX ATT INPUT
BIAS AGC
GCA
PROGRAMMABLE
EQUALIZER
FILTER
DIFFERENTIATOR
64 63 62 61 60 59 58 57 5156
1
2
FULL WAVE
RECTIFER
AGC CHARGE
PUMP
+
–
+
–
+
+
+
+
+
+
+
+
+
+
––
+
–
+
–
INPUT
SEL ATT
2
4
2
2
INPUT
IMPEDANCE
SEL
OFFSET
CANSEL
MNTR
CONTROL
SERIAL
PORT
REGISTER
4
FROM
S-PORT
4
FROM
S-PORT
INPUT
IMPEDANCE
SEL
3
FROM
S-PORT
CLAMP &
ENVELOPE
LEVEL
DAC
SIGDET
AGCO
BUFFER
55 54 53 52 50 49
OUTPUT
INHIBIT
FROM S-PORT
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
GCA
CD/DVD
4
FROM
S-PORT
3
FROM
S-PORT
MUX
3
FROM
S-PORT
GCA
3
FROM
S-PORT
3
FROM
S-PORT
EQ
VC
COMPARATOR
PHASE
DETECTOR
PHASE
DETECTOR
A+D
B+D
+
+
A+C
B+C
GCA
W/LPF
SUM
AMP
18 19 20 21 22 24 2523 26 27 28 29 31 3230
GCA
GCA
VCI FOR SERVO INPUT
VC = VPB/2
DUAL APC
LD H/L
FROM S-PORT
APC SEL
DVD/CD
TOPHOLD
GCA
TOPHOLD
GCA
41
48
47
46
45
GCA
OFFSET
CANSEL
5
FROM
S-PORT
GCA 40
GCA
OFFSET
CANSEL
6
FROM
S-PORT
3
FROM
S-PORT
GCAGCA
CEFDB
CP/CN
LOW
IMPEDANCE
CD/DVD
SUBGCAMUX GCALPF
GCALPF
39
38
37
36
OFFSET
CANSEL
PEAK/BOTTOM
HOLD
BOTTOM
ENVELOPE
INPUT
BUFFER
5
FROM
S-PORT
GCALPF
V25/2
TE
RST
35
34
33
FOR SERVO
OUTPUT
PH
TOP
HOLD
GCASEL
LINKEN
MUX
HOLDEN
+
–
+
–
COMPA-
RATOR
INTERNAL
FDGHG
HYSTERESISTER
& OFFSET
FROM S-PORT
MIRR
COMPARATOR
INPUT GAIN
FROM S-PORT
SEL
DAC
SINK CURRENT
FROM S-PORT
2
AGCO
FAST ATTACK
AGC
HOLD
BCA
DET
2
FROM
S-PORT
PH
2
2
INPUT
IMPEDANCE
FROM S-PORT
44
43
42
V33 FOR
OUTPUT
BUFFER
PI
FE
TE
CE
V25
V125
V25/3
LPF ATT
POL SEL
BUFFER
CONTROL
SIGNALS
TO EACH
BLOCK
3
CE ATT
CEPOL
D
C
B
A
CD F
CD E
VPB
VC
DVDLD
CDLD
CDPD
DVDPD
LDON
VNB
MIRR
MP
MB
MIN
MEVO
MLPF
CE
SDEN
SDATA
SCLK
V33
FE
TE
PI
V25
V125
TPH
DFT
LINK
LPC
LCN
MNTR
DVDRFP
DVDRFN
A2
B2
C2
D2
CP
CN
D
C
B
A
CD D
CD C
CD B
CD A
RFDC
RFSIN
ATOP
ATON
AIN
AIP
VPA
RFAC
VNA
BYP
DIN
DIP
FNP
FNN
MEV
RX
CD E
IC302 PCM1609KPTR (DMB07 Board)
IC701 BA6956AN (DRIVER Board)
IC712 BA6956AN (DRIVER Board) IC509 CXD3068Q (DMB07 Board)
SYSTEM
CLOCK
MANAGER
FUNCTION
CONTROL
INTERFACE
SERIAL
INPUT
INTERFACE
4X/8X
OVER SAMPLING
DIGITAL
FILTER
WITH
FUNCTION
CONTROLLER
ENHANCED
MULTI-
LEVEL
DELTA-
SIGMA
MOJULE
ZERO DETECT
DAC LPF
DAC LPF
DAC LPF
DAC LPF
DAC LPF
DAC LPF
DAC LPF
DAC LPF
RST
SCKI
SCKO
BCK
TEST
VDD
DGND
DATA1
DATA2
DATA3
ZEROA
LRCK
37
38
39
40
42
43
44
45
46
47
48
41
ZERO1/GPO1
ZERO2/GPO2
ZERO3/GPO3
ZERO4/GPO4
ZERO5/GPO5
ZERO6/GPO6
NC
NC
VOUT6
VOUT5
VOUT4
VOUT3
1 2 3 4 5 6 7 8 9 10 11 12
VOUT2
VOUT1
VCOM
VOUT7
AGND5
VCC5
AGND6
VOUT8
AGND4
VCC4
AGND3
VCC3
13
14
15
16
17
18
19
20
21
22
23
24
ML
MC
MDI
MDO
ZERO8
DATA4
ZERO7
NC
VCC1
AGND1
VCC2
AGND2
36 35 34 33 32 31 30 29 28 27 26 25
1 2 3 4 5 6 7 8 9
CONTROL LOGIC
TSD
VREF
OUT2
OUT1
RNF
VM
VCC
FIN
GND
RIN
CE
RFDC
ADIO
IGEN
ASYO
ASYI
RFAC
CLTV
FILO
FILI
PCO
BIAS
VCTL
V16M
VPCO
TE
ASYE
MD2
DOUT
LRCK
PCMD
BCK
EMPH
XTSL
XTAI
XTAO
SOUT
SOCK
XOLT
SQSO
SQCK
SCSY
SBSO
EXCK
XRST
MUTE
DATA
XLAT
CLOK
SENS
SCLK
ATSK
WFCK
XUGF
XPCK
GFS
C2PO
SCOR
CAM
WDCK
COUT
MIRR
SE
FE
VC
TES1
TEST
FFDR
TRDR
TFDR
SRDR
SFDR
FSTO
SSTP
LOCK
PWMI
FOK
FRDR
MDP
DFCT
CLOCK
GENERATOR
ASYMMETRY
CORRECTOR
DIGITAL
PLL
CPU
INTERFACE
INTERFACE
CORRECTOR
PROCESSOR
SUB CODE
RAM
32K
DEMODURATOR
EFM
ERROR
D/A
DIGITAL
OUT
INTERFACE
SERVO
INTERFACE
SERVO
AUTO
MIRR
DFCT
FOK
SERVO
FOCUS
SERVO DSP
SERVO
SERVO
SLED
TRACKING
FOCUS PWM
GENERATOR
GENERATOR
GENERATOR
SLED PWM
TRACKING PWM
A/D
CONVERTER
OPAMP
ANALOG SW
PWM GENERATOR
DIGITAL
CLV
SERVO BLOCK
85
HCD-RV777D/RV888D/RV999D
IC331 PCM1751DBQR (DMB07 Board)
IC906 SM8707GV-G-E2 (DMB07 Board)
IC903 BR24C16F-WE2 (DMB07 Board)
1
2
3
4
5
6
7
12
11
10
POWER
SUPPLY
OUTPUT AMP
AND
LOW-PASS
FILTER
SERIAL
CONTROL
PORT
AUDIO
SERIAL
PORT
ENHANCED
MULTI-LEVEL
DELTA-SIGMA
MODULATOR
4x/8x
OVERSAMPLING
DIGITAL
FILTER
WITH
FUNCTION
CONTROLLER
ZERO
DETECT
DAC
8
9
OUTPUT AMP
AND
LOW-PASS
FILTER
DAC
15
14
13
16
SYSTEM
CLOCK
MANAGER
SYSTEM
CLOCK
BCK
DATA
LRCK
L OUT
R OUT
AGND
SCK
ML
MC
MD
ZL/NA
ZR/ZA
VCOM
DGND
VDD
VCC
8
VCC
7
TEST
6
SCL
5
SDA
1A0
2A1
3A2
4GND
ADDRESS
DECODER
SLAVE WORD
ADDRESS REGISTER
DATA
REGISTER
16 K bit EEPROM ARRAY
CONTROL CIRCUIT
POWER SUPPLY
VOLTAGE DETECTION
HIGHT VOLTAGE
GENERATOR
11 bit 8 bit
11 bit
STOPSTART
ACK
VDD1
VSS1
MO1
NC
REF
Div.1
PHASE
DETECTOR1
PHASE
PUMP1 LPF
LOOP
Div.1
X'tal
OSC
CONTROL
LOGIC
NC
16
NC
15
NC
14
SO3
13
VDD3
12
VSS3
11
SO2
10
SO1
9
4
3
VDD2
VSS2 6
XTI 7
XTO 8
5
1
2
VCO
86
HCD-RV777D/RV888D/RV999D
IC204 BR9040F-WE2 (DMB07 Board)
IC252 TC7WH157FK (TE85R)
(DMB07 Board)
IC802 NJM2244M-TE2 (VIDEO Board)
1
2
3
4
INSTRUCTION DECODE
CONTROL AND CLOCK
GENERATOR
ADDRESS
BUFFER
INSTRUCTION
REGISTER
DATA
REGISTER
4,096bit
EEPROM
R/W
AMPS
HIGH
VOLTAGE
GENERATOR
R/B
VCC
CS
SK
16bit
8bit
16bit
8WC
7
6
5
GND
DO
DI
WRITE
DISABLE
DETECT
SUPPLY
VOLTAGE
8bit
ADDRESS
DECODER
SELECT
116
ST
117
A1
2
3
A
B
Y
5
Y
B
GND 4
VCC
8
Y
EN G
Y
2
SW1
3
VIN2
4
SW2
1
VIN1 8 GND
7 VOUT
6V+
5 VIN3 (MUTE)
BIAS
75Ω
DRIVER
87
HCD-RV777D/RV888D/RV999D
SECTION 8
EXPLODED VIEWS
NOTE:
•The mechanical parts with no reference
number in the exploded views are not supplied.
•Items marked “*” are not stocked since
they are seldom required for routine service.
Some delay should be anticipated
when ordering these items.
•-XX and -X mean standardized parts, so
they may have some difference from the
original one.
•Accessories are given in the last of this
parts list.
• Abbreviation
E3 : 240 V AC area in E model
E15 : Iran model
E51 : 220 V AC area in E model
AUS: Australian model
EA : Saudi Arabia model
PH : Philippine model
SP : Singapore model
AR : Argentina model
MY : Malaysia model
MX : Mexican model
Ref. No. Part No. Description Remark
8-1. MAIN SECTION
Ref. No. Part No. Description Remark
1X-4956-366-1 DOOR (CD-9) ASSY (RV999D)
1X-4956-367-1 DOOR (CD-8) ASSY (RV888D)
1X-4956-368-1 DOOR (CD-7) ASSY (RV777D)
21-828-965-11 WIRE (FLAT TYPE) (11 CORE)
33-363-099-02 SCREW (CASE 3 TP2)
43-363-099-32 SCREW (CASE 3 TP2)
54-248-760-22 CASE, CABINET STEEL
0F911 1-533-472-12 FUSE, GLASS TUBE (DIA.5) (5A/250V)
(EXCEPT AUS,AR,MX)
0F912 1-533-472-12 FUSE, GLASS TUBE (DIA.5) (5A/250V)
(EXCEPT AUS,AR,MX)
0F913 1-533-472-12 FUSE, GLASS TUBE (DIA.5) (5A/250V)
(RV888D:AUS/RV999D:AUS,AR)
0F913 1-533-473-12 FUSE, GLASS TUBE (DIA.5) (6.3A/250V)
(RV777D)
0F913 1-576-655-12 FUSE, GLASS TUBE (DIA.5) (8A/250V)
(RV888D:EXCEPT AUS/
RV999D:EXCEPT AUS,AR)
FAN901 1-763-072-11 FAN, DC
FC901 1-500-386-11 FILTER, CLAMP (FERRITE CORE) (AUS,EA)
TM901 1-693-603-31 TUNER PACK (FM/AM) (ANTENNA)
#1 7-685-650-79 SCREW +BVTP 3X16 TYPE2 IT-3
#2 7-685-871-01 SCREW +BVTT 3X6 (S)
#3 7-685-646-79 SCREW +BVTP 3X8 TYPE2 TT (B)
#5 7-685-647-79 SCREW +BVTP 3X10 TYPE2 TT (B)
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
not
supplied
#3
#2
#2
#2
#3
#2
#2
#5
#5
#5
#5
#1
#2
#5
#2
#2
FAN901
F911
F912
F913
FC901
not supplied
not supplied
not supplied
(SUB TRANS BOARD)
front panel
section main board section
DVD block section
TM901
3
1
4
5
2
4
3
88
HCD-RV777D/RV888D/RV999D
8-2. FRONT PANEL SECTION (1)
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
51 4-951-620-01 SCREW (2.6X8), +BVTP
52 1-796-487-61 DECK, MECHANICAL
53 4-243-608-01 BELT (BR)
54 4-243-609-01 BELT (AF)
55 4-243-610-01 BELT (AL)
56 1-828-974-11 WIRE (FLAT TYPE) (13 CORE)
57 4-245-758-02 PLATE (HEAD), SHIELD
58 1-828-338-11 WIRE (FLAT TYPE) (15 CORE)
59 4-238-628-03 KNOB, MIC
60 A-4751-844-A PANEL BOARD, COMPLETE
61 A-1053-972-A JACK BOARD, COMPLETE
(RV999D:E51,AR,MX)
61 A-4751-845-A JACK BOARD, COMPLETE
(EXCEPT RV999D:E51,AR,MX)
FL1001 1-518-989-11 INDICATOR TUBE, FLUORESCENT
#4 7-685-853-04 SCREW +BVTT 2X6 (S)
not supplie
d
not supplied
not supplied
not supplied
not supplied
(HP board)
MX model
FL1001
not supplied
(SIRCS board)
51
51
51
51
51
52
54
53
55
56
57
61
59
51
51
51
51
60
58
A
A
#4
57
51 51
#4
89
HCD-RV777D/RV888D/RV999D
8-3. FRONT PANEL SECTION (2)
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
101 4-231-841-01 SPRING (HEART CAM-B)
102 4-231-825-01 CAM (B), HEART
103 4-224-104-41 DAMPER
104 4-231-824-01 CAM (A), HEART
105 4-231-836-01 SPRING (HEART CAM-A)
106 4-252-218-11 BUTTON (VIDEO/SAT)
107 4-252-203-21 BUTTON (POWER)
not supplie
d
not supplied
101 102
103
103
104
105
106
107
90
HCD-RV777D/RV888D/RV999D
8-4. FRONT PANEL SECTION (3)
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
151 4-252-202-11 DOOR (B), CASS
152 4-252-201-11 DOOR (A), CASS
153 4-951-620-01 SCREW (2.6X8), +BVTP
154 4-252-214-01 KNOB, VOLUME
155 X-4956-295-1 RING ASSY, KNOB
156 4-252-198-01 WINDOW, DISPLAY
157 4-238-631-01 SPRING, TAPE
158 4-252-205-11 BUTTON (PLAY)
159 4-252-207-11 BUTTON (FF/ALBUM+)
160 4-252-200-01 COVER, BUTTON
161 4-252-208-11 BUTTON (FR/ALBUM–)
162 4-252-206-01 BUTTON (STOP)
163 4-233-980-01 FOOT, RUBBER
164 4-253-804-21 PANEL, FRONT
(RV888D/RV999D:EXCEPT E51,AR,MX)
164 4-253-804-31 PANEL, FRONT (RV999D:E51,AR,MX)
164 4-253-804-41 PANEL, FRONT (RV777D)
not supplied
not supplied
163
157
157
151
152
164
not supplied
not supplied
not supplied
not supplied
153
153
154
155 156
161
158
159
162
160
not supplied
(P-STREAM board)
91
HCD-RV777D/RV888D/RV999D
8-5. DVD BLOCK SECTION
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
201 A-4751-861-A VIDEO BOARD, COMPLETE
202 1-828-895-11 WIRE (FLAT TYPE) (15 CORE)
203 1-828-288-11 WIRE (FLAT TYPE) (5 CORE)
204 1-828-333-11 WIRE (FLAT TYPE) (13 CORE) (RV777D)
204 1-828-393-11 WIRE (FLAT TYPE) (25 CORE)
(RV888D/RV999D)
205 A-4751-975-A DMB07 BOARD, COMPLETE (RV999D)
205 A-4751-976-A DMB07 BOARD, COMPLETE (RV888D)
205 A-4751-977-A DMB07 BOARD, COMPLETE (RV777D)
#2 7-685-871-01 SCREW +BVTT 3X6 (S)
#3 7-685-646-79 SCREW +BVTP 3X8 TYPE2 TT (B)
#3
#3
#3
#3
#2
#2
not supplied
not supplied
not supplied
not supplied
CDM74S-DVBU62
not supplied
not supplied
not supplied
not supplied
not supplied
not
supplied
201
202
203
204
205
92
HCD-RV777D/RV888D/RV999D
8-6. MAIN BOARD SECTION (1/2)
251
252
254
256
255
255
258
257
253
F917
T911
F916
HCD-RV888D/RV999D
F914
F915
F918
F919
#2
#2
#2
#3
#2
#1
#1
#1
#1
IC201
IC301
IC932
IC934
IC923
IC922
IC921
#2
#2
not supplied
not supplied
not supplied
not supplied
not supplied
not supplied
HCD-RV777D
#3
not supplied
not supplied
(LEAD PIN board)
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
251 A-1053-866-A MAIN BOARD, COMPLETE (RV999D:SP,MY,PH)
251 A-1053-867-A MAIN BOARD, COMPLETE (RV999D:EA)
251 A-1053-868-A MAIN BOARD, COMPLETE (RV999D:AUS)
251 A-1053-869-A MAIN BOARD, COMPLETE
(RV999D:E51,AR,MX)
251 A-1053-871-A MAIN BOARD, COMPLETE (RV888D:SP,MY)
251 A-1053-872-A MAIN BOARD, COMPLETE (RV888D:EA)
251 A-1053-873-A MAIN BOARD, COMPLETE (RV888D:AUS)
251 A-1053-875-A MAIN BOARD, COMPLETE (RV777D:SP,MY,PH)
251 A-1053-876-A MAIN BOARD, COMPLETE (RV777D:EA)
251 A-4751-800-A MAIN BOARD, COMPLETE (RV999D:E3,E15)
251 A-4751-804-A MAIN BOARD, COMPLETE (RV888D:E3,E15)
251 A-4751-806-A MAIN BOARD, COMPLETE (RV777D:E3,E15)
252 4-233-980-01 FOOT, RUBBER
0253 1-696-848-22 CORD, POWER (AUS)
0253 1-751-520-21 CORD, POWER (EA)
0253 1-777-071-83 CORD, POWER (E51,PH,SP,MY)
0253 1-783-941-22 CORD, POWER (AR)
0253 1-827-226-11 CORD, POWER (E3,E15,MX)
254 A-1053-996-A TRANS BOARD, COMPLETE (AUS)
254 A-1053-997-A TRANS BOARD, COMPLETE (E51)
254 A-1053-998-A TRANS BOARD, COMPLETE (MX)
254 A-1053-999-A TRANS BOARD, COMPLETE (AR)
254 A-4751-863-A TRANS BOARD, COMPLETE
(RV888D:EXCEPT AUS/
RV999D:EXCEPT E51,AUS,AR,MX)
254 A-4751-866-A TRANS BOARD, COMPLETE (RV777D)
93
HCD-RV777D/RV888D/RV999D
8-7. MAIN BOARD SECTION (2/2)
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
251
252
254
256
255
255
258
257
253
F917
T911
F916
HCD-RV888D/RV999D
F914
F915
F918
F919
#2
#2
#2
#3
#2
#1
#1
#1
#1
IC201
IC301
IC932
IC934
IC923
IC922
IC921
#2
#2
not supplied
not supplied
not supplied
not supplied
not supplied
not supplied
HCD-RV777D
#3
not supplied
not supplied
(LEAD PIN board)
255 4-900-386-01 SCREW
256 A-1053-978-A FRONT AMP BOARD, COMPLETE (RV888D)
256 A-4751-854-A FRONT AMP BOARD, COMPLETE (RV999D)
256 A-4751-856-A FRONT AMP BOARD, COMPLETE (RV777D)
257 A-1053-983-A SURROUND AMP BOARD, COMPLETE (RV888D)
257 A-4751-859-A SURROUND AMP BOARD, COMPLETE (RV999D)
258 3-703-244-00 BUSHING (2104), CORD (EXCEPT E3,E15,MX)
*258 3-703-571-12 BUSHING (S) (4516), CORD (E3,E15,MX)
0F914 1-533-473-12 FUSE, GLASS TUBE (DIA.5) (6.3A/250V)
0F915 1-533-473-12 FUSE, GLASS TUBE (DIA.5) (6.3A/250V)
0F916 1-533-473-12 FUSE, GLASS TUBE (DIA.5) (6.3A/250V)
(RV888D/RV999D)
0F917 1-533-473-12 FUSE, GLASS TUBE (DIA.5) (6.3A/250V)
(RV888D/RV999D)
0F918 1-533-471-12 FUSE, GLASS TUBE (DIA.5) (4A/250V)
(RV777D)
0F918 1-533-472-12 FUSE, GLASS TUBE (DIA.5) (5A/250V)
(RV888D/RV999D)
0F919 1-533-471-12 FUSE, GLASS TUBE (DIA.5) (4A/250V)
IC201 6-705-853-01 IC STK403-120
IC301 6-703-651-11 IC M61530FP-D60G (RV888D/RV999D)
IC921 8-759-518-68 IC PQ12RF21
IC922 8-759-701-59 IC NJM78M09FA
IC923 8-759-701-59 IC NJM78M09FA
IC932 6-703-546-01 IC TA7804LS
IC934 8-759-231-53 IC TA7805S
0T911 1-443-174-11 TRANSFORMER, POWER (RV777D:EXCEPT EA)
0T911 1-443-175-11 TRANSFORMER, POWER (RV777D:EA)
0T911 1-443-352-11 TRANSFORMER, POWER
(RV888D:EXCEPT EA/RV999D:EXCEPT EA,MX)
0T911 1-443-362-11 TRANSFORMER, POWER
(RV888D:EA/RV999D:EA,MX)
#1 7-685-650-79 SCREW +BVTP 3X16 TYPE2 IT-3
#2 7-685-871-01 SCREW +BVTT 3X6 (S)
#3 7-685-646-79 SCREW +BVTP 3X8 TYPE2 TT (B)
94
HCD-RV777D/RV888D/RV999D
8-8. DVD MECHANISM DECK SECTION (1)
(CDM74S-DVBU62)
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
301
302
316
303
304
305
305
306
306
307
307
308
308 309
301
306
312
313
314
315
310
311 314
M741
chassis assy
301 4-218-253-21 SCREW (M2.6), +BTTP
302 1-776-182-11 WIRE (FLAT TYPE) (5 CORE)
303 1-687-134-12 MOTOR (TB) BOARD
304 4-243-815-01 TABLE (LOADING)
305 4-245-571-02 GEAR (STOPPER)
306 4-218-252-61 SCREW (+PTPWH M2.6), FLOATING
307 4-245-570-01 GEAR (JOINT)
308 4-245-572-01 BUSHING (GEAR)
309 1-687-132-12 SENSOR BOARD
310 4-243-820-01 GEAR (TABLE)
311 4-243-819-01 GEAR (GENEVA)
312 4-243-816-01 TRAY
313 4-243-823-01 BELT (TABLE)
314 4-985-672-01 SCREW (+PTPWH M2.6), FLOATING
315 4-243-821-01 PULLEY (TABLE)
316 3-231-598-01 SHEET (BA)
M741 A-4723-963-A MOTOR ASSY, TABLE (TABLE)
95
HCD-RV777D/RV888D/RV999D
8-9. DVD MECHANISM DECK SECTION (2)
(CDM74S-DVBU62)
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
351
352
352
352
353
354
355
356
357
358
359
360
361 362
363
364
365
366
368
369
369
370
370
371
372
373
375
374
378
369
367
376
377
355
355
355
355
M751
#6
RE701
351 1-687-135-12 DRIVER BOARD
352 4-218-253-31 SCREW (M2.6), +BTTP
353 1-687-669-12 SW BOARD
354 4-244-034-01 BELT (LOADING)
355 4-218-252-61 SCREW (+PTPWH M2.6), FLOATING
356 4-225-844-01 GEAR (LOADING A)
357 4-224-613-01 GEAR (SHAFT)
358 1-687-133-12 MOTOR (LD) BOARD
359 4-244-108-01 GEAR, SWING
360 4-224-609-01 GEAR (LOADING C)
361 4-224-608-01 COLLAR, SWING
362 3-016-533-11 WASHER (FR), STOPPER
363 4-224-611-01 GEAR (LOADING B)
364 4-224-606-01 GEAR (RV)
365 4-243-818-01 GEAR (U/D)
366 4-243-822-02 LEVER (LIFTER)
367 4-243-817-11 CHASSIS
368 4-233-594-01 PULLEY (B) (DVD), CHUCKING
369 4-981-923-01 SCREW (M), STEP
370 3-057-023-11 INSULATOR (RB)
0371 A-1067-676-A OPTICAL PICK-UP (DBU-3)
372 X-4955-538-1 HOLDER (DBU) ASSY
373 1-824-106-12 CABLE, FLEXIBLE FLAT (24 CORE)
374 1-828-672-11 WIRE (FLAT TYPE) (29 CORE)
375 A-4728-690-A RF BOARD, COMPLETE
376 X-4954-450-1 PULLEY (240) ASSY
377 3-053-844-01 YOKE
378 3-053-847-41 INSULATOR
M751 A-4736-655-A MOTOR ASSY, LOADING (LOADING)
RE701 1-477-680-12 ENCODER, ROTARY
(DISC TRAY ADDRESS DETECT)
#6 7-685-533-19 SCREW +BTP 2.6X6 TYPE2 N-S
96
HCD-RV777D/RV888D/RV999D SECTION 9
ELECTRICAL PARTS LIST
NOTE:
•Due to standardization, replacements in
the parts list may be different from the
parts specified in the diagrams or the
components used on the set.
•-XX and -X mean standardized parts, so
they may have some difference from the
original one.
•RESISTORS
All resistors are in ohms.
METAL:Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F:nonflammable
•Items marked “*” are not stocked since
they are seldom required for routine service.
Some delay should be anticipated
when ordering these items.
•SEMICONDUCTORS
In each case, u : µ, for example:
uA.. : µA.. uPA.. : µPA..
uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD..
•CAPACITORS
uF : µF
•COILS
uH : µH
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
When indicating parts by reference
number, please include the board.
A-4751-975-A DMB07 BOARD, COMPLETE (RV999D)
A-4751-976-A DMB07 BOARD, COMPLETE (RV888D)
A-4751-977-A DMB07 BOARD, COMPLETE (RV777D)
***********************
< CAPACITOR >
C101 1-126-246-11 ELECT CHIP 220uF 20% 4V
C151 1-126-206-11 ELECT CHIP 100uF 20% 6.3V
C201 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C202 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C203 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C204 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C205 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C213 1-126-209-11 ELECT CHIP 100uF 20% 4V
C214 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C215 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C216 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C218 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C220 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C226 1-107-820-11 CERAMIC CHIP 0.1uF 16V
C227 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C229 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C230 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C231 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C232 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C233 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C234 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C235 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C236 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C237 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C238 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C239 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C240 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C241 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C242 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C243 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C244 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C245 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C246 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C247 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C248 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C249 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C250 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C251 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C252 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C253 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C254 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C255 1-117-370-11 CERAMIC CHIP 10uF 10V
C256 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C257 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C258 1-117-370-11 CERAMIC CHIP 10uF 10V
C259 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C260 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C261 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C262 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C263 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C264 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C265 1-117-370-11 CERAMIC CHIP 10uF 10V
C266 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C267 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C268 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C269 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C270 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C271 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C272 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C274 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C275 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C276 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C277 1-164-874-11 CERAMIC CHIP 100PF 5% 50V
C278 1-164-874-11 CERAMIC CHIP 100PF 5% 50V
C279 1-164-874-11 CERAMIC CHIP 100PF 5% 50V
C280 1-164-874-11 CERAMIC CHIP 100PF 5% 50V
C281 1-164-874-11 CERAMIC CHIP 100PF 5% 50V
C282 1-164-874-11 CERAMIC CHIP 100PF 5% 50V
C283 1-164-874-11 CERAMIC CHIP 100PF 5% 50V
C289 1-164-947-11 CERAMIC CHIP 0.01uF 50V
(RV777D)
C290 1-164-874-11 CERAMIC CHIP 100PF 5% 50V
C291 1-164-874-11 CERAMIC CHIP 100PF 5% 50V
C302 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
(RV888D/RV999D)
C303 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
(RV888D/RV999D)
C304 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
(RV888D/RV999D)
C305 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
(RV888D/RV999D)
C306 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
(RV888D/RV999D)
C307 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
(RV888D/RV999D)
• Abbreviation
E3 : 240 V AC area in E model
E15 : Iran model
E51 : 220 V AC area in E model
AUS: Australian model
EA : Saudi Arabia model
PH : Philippine model
SP : Singapore model
AR : Argentina model
MY : Malaysia model
MX : Mexican model
DMB07
97
HCD-RV777D/RV888D/RV999D
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
C308 1-164-874-11 CERAMIC CHIP 100PF 5% 50V
C309 1-164-874-11 CERAMIC CHIP 100PF 5% 50V
C321 1-126-206-11 ELECT CHIP 100uF 20% 6.3V
(RV888D/RV999D)
C322 1-107-820-11 CERAMIC CHIP 0.1uF 16V
(RV888D/RV999D)
C323 1-107-820-11 CERAMIC CHIP 0.1uF 16V
(RV888D/RV999D)
C324 1-107-820-11 CERAMIC CHIP 0.1uF 16V
(RV888D/RV999D)
C325 1-126-209-11 ELECT CHIP 100uF 20% 4V
(RV888D/RV999D)
C326 1-164-947-11 CERAMIC CHIP 0.01uF 50V
(RV888D/RV999D)
C342 1-107-820-11 CERAMIC CHIP 0.1uF 16V
(RV777D)
C343 1-124-779-00 ELECT CHIP 10uF 20% 16V
(RV777D)
C344 1-107-820-11 CERAMIC CHIP 0.1uF 16V
(RV777D)
C345 1-124-779-00 ELECT CHIP 10uF 20% 16V
(RV777D)
C346 1-124-779-00 ELECT CHIP 10uF 20% 16V
(RV777D)
C392 1-126-395-11 ELECT CHIP 22uF 20% 16V
C393 1-164-947-11 CERAMIC CHIP 0.01uF 50V
C394 1-126-246-11 ELECT CHIP 220uF 20% 4V
C501 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C502 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C503 1-127-772-81 CERAMIC CHIP 0.033uF 10% 10V
C504 1-127-772-81 CERAMIC CHIP 0.033uF 10% 10V
C506 1-164-934-11 CERAMIC CHIP 330PF 10% 50V
C507 1-117-370-11 CERAMIC CHIP 10uF 10V
C508 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V
C509 1-164-934-11 CERAMIC CHIP 330PF 10% 50V
C510 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V
C511 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C512 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C513 1-117-370-11 CERAMIC CHIP 10uF 10V
C514 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C515 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C516 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 50V
C517 1-117-370-11 CERAMIC CHIP 10uF 10V
C518 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C519 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C522 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C523 1-107-820-11 CERAMIC CHIP 0.1uF 16V
C524 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C525 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C526 1-126-395-11 ELECT CHIP 22uF 20% 16V
C527 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C528 1-126-395-11 ELECT CHIP 22uF 20% 16V
C529 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C531 1-119-923-11 CERAMIC CHIP 0.047uF 10% 10V
C532 1-117-370-11 CERAMIC CHIP 10uF 10V
C533 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 50V
C534 1-107-819-11 CERAMIC CHIP 0.022uF 10% 16V
C535 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 50V
C540 1-117-370-11 CERAMIC CHIP 10uF 10V
C543 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C544 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C545 1-117-370-11 CERAMIC CHIP 10uF 10V
C547 1-107-725-11 CERAMIC CHIP 0.1uF 10% 16V
C548 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C551 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10V
C552 1-216-295-11 SHORT CHIP 0
C553 1-164-940-11 CERAMIC CHIP 0.0033uF 10% 16V
C556 1-117-370-11 CERAMIC CHIP 10uF 10V
C558 1-126-209-11 ELECT CHIP 100uF 20% 4V
C559 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C560 1-164-938-11 CERAMIC CHIP 0.0015uF 10% 50V
C561 1-107-820-11 CERAMIC CHIP 0.1uF 16V
C563 1-164-874-11 CERAMIC CHIP 100PF 5% 50V
C565 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C567 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C568 1-117-370-11 CERAMIC CHIP 10uF 10V
C569 1-107-820-11 CERAMIC CHIP 0.1uF 16V
C570 1-117-370-11 CERAMIC CHIP 10uF 10V
C573 1-164-874-11 CERAMIC CHIP 100PF 5% 50V
C588 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 50V
C589 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 50V
C590 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 50V
C592 1-126-208-21 ELECT CHIP 47uF 20% 4V
C701 1-100-391-21 ELECT CHIP 180uF 20% 2.5V
C702 1-117-370-11 CERAMIC CHIP 10uF 10V
C703 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C705 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C706 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C708 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C709 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C711 1-119-923-11 CERAMIC CHIP 0.047uF 10% 10V
C712 1-164-874-11 CERAMIC CHIP 100PF 5% 50V
C713 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C714 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C715 1-164-938-11 CERAMIC CHIP 0.0015uF 10% 50V
C716 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10V
C717 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C718 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C720 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C721 1-107-820-11 CERAMIC CHIP 0.1uF 16V
C722 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C723 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C724 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C725 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C726 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C727 1-117-370-11 CERAMIC CHIP 10uF 10V
C728 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C729 1-117-370-11 CERAMIC CHIP 10uF 10V
C730 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C733 1-117-370-11 CERAMIC CHIP 10uF 10V
C734 1-117-370-11 CERAMIC CHIP 10uF 10V
C740 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C741 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C742 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C743 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C744 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C745 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C752 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
DMB07
98
HCD-RV777D/RV888D/RV999D
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
C760 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C761 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C762 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C763 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C764 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C765 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C766 1-164-874-11 CERAMIC CHIP 100PF 5% 50V
C767 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C768 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C769 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C770 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C771 1-119-923-11 CERAMIC CHIP 0.047uF 10% 10V
C772 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C773 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10V
C774 1-164-941-11 CERAMIC CHIP 0.0047uF 10% 16V
C775 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C776 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C777 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C778 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C779 1-117-370-11 CERAMIC CHIP 10uF 10V
C780 1-117-370-11 CERAMIC CHIP 10uF 10V
C781 1-165-643-21 ELECT CHIP 150uF 20% 4V
C782 1-164-938-11 CERAMIC CHIP 0.0015uF 10% 50V
C783 1-164-938-11 CERAMIC CHIP 0.0015uF 10% 50V
C901 1-126-209-11 ELECT CHIP 100uF 20% 4V
C902 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C903 1-126-209-11 ELECT CHIP 100uF 20% 4V
C904 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C905 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C906 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C907 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C908 1-164-874-11 CERAMIC CHIP 100PF 5% 50V
C909 1-164-874-11 CERAMIC CHIP 100PF 5% 50V
C910 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C913 1-127-772-81 CERAMIC CHIP 0.033uF 10% 10V
C914 1-117-745-81 CERAMIC CHIP 7PF 16V
C915 1-117-745-81 CERAMIC CHIP 7PF 16V
C916 1-126-209-11 ELECT CHIP 100uF 20% 4V
C917 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C918 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C924 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C925 1-126-395-11 ELECT CHIP 22uF 20% 16V
C926 1-126-246-11 ELECT CHIP 220uF 20% 4V
C927 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C928 1-117-370-11 CERAMIC CHIP 10uF 10V
C1302 1-164-874-11 CERAMIC CHIP 100PF 5% 50V
< CONNECTOR >
CN101 1-784-365-21 CONNECTOR, FFC/FPC 5P
CN102 1-815-954-21 PIN, CONNECTOR (PC BOARD) 13P
CN105 1-784-374-21 CONNECTOR, FFC/FPC 15P
CN107 1-793-989-21 CONNECTOR, FFC/FPC 13P (RV777D)
CN107 1-784-382-21 CONNECTOR, FFC/FPC 25P (RV888D/RV999D)
CN202 1-784-364-21 CONNECTOR, FFC/FPC 4P
CN501 1-778-957-11 CONNECTOR, FFC/FPC 29P
CN901 1-764-177-11 PIN, CONNECTOR (SMD) (1.5mm) 7P
< DIODE >
D202 8-719-988-61 DIODE 1SS355TE-17
D392 8-719-988-61 DIODE 1SS355TE-17
D393 8-719-988-61 DIODE 1SS355TE-17
D394 8-719-988-61 DIODE 1SS355TE-17
D901 8-719-988-61 DIODE 1SS355TE-17
D1303 8-719-988-61 DIODE 1SS355TE-17
D1304 8-719-988-61 DIODE 1SS355TE-17
< FERRITE BEAD >
FB105 1-469-324-21 FERRITE, EMI (SMD) (2012)
FB902 1-500-284-21 INDUCTOR, FERRITE BEAD
FB903 1-500-284-21 INDUCTOR, FERRITE BEAD
< FILTER >
FL101 1-234-177-21 FILTER, CHIP EMI
FL203 1-234-177-21 FILTER, CHIP EMI
FL204 1-234-177-21 FILTER, CHIP EMI
FL205 1-234-177-21 FILTER, CHIP EMI
FL206 1-234-177-21 FILTER, CHIP EMI
FL302 1-234-117-21 FILTER, CHIP EMI
FL303 1-234-117-21 FILTER, CHIP EMI
FL501 1-234-177-21 FILTER, CHIP EMI
FL502 1-234-177-21 FILTER, CHIP EMI
FL701 1-234-177-21 FILTER, CHIP EMI
FL702 1-234-177-21 FILTER, CHIP EMI
FL703 1-234-177-21 FILTER, CHIP EMI
FL705 1-234-177-21 FILTER, CHIP EMI
FL706 1-234-177-21 FILTER, CHIP EMI
FL901 1-234-177-21 FILTER, CHIP EMI
FL903 1-234-177-21 FILTER, CHIP EMI
FL908 1-234-177-21 FILTER, CHIP EMI
< TRANSISTOR >
IC111 6-550-554-01 TRANSISTOR UM6K1NL02TN
< IC >
IC203 6-704-069-01 IC MT48LC4M32B2P-6-Y15W
*IC204 6-703-671-01 IC BR9040F-WE2
IC206 6-804-626-01 IC MBM29PL32BM90TN-GY0402
IC207 6-704-630-01 IC ZIVA5X-C2F
IC211 6-700-398-01 IC uPC2918T-E1
IC231 8-759-549-21 IC SN74LV573APWR
IC232 8-759-549-21 IC SN74LV573APWR
IC233 8-759-549-21 IC SN74LV573APWR
IC252 8-759-680-48 IC TC7WH157FK(TE85R) (RV777D)
IC302 6-703-787-01 IC PCM1609KPTR (RV888D/RV999D)
IC331 6-703-788-01 IC PCM1751DBQR (RV777D)
IC392 8-759-583-47 IC uPC2933T-E2
IC501 6-702-157-01 IC FAN8035L
IC503 8-759-058-43 IC NJM3404AV(TE2)
IC509 8-752-408-73 IC CXD3068Q
IC701 6-703-552-01 IC TMC57929PGF-RDP
IC703 8-759-058-43 IC NJM3404AV(TE2)
IC706 8-759-564-30 IC MSM51V18165B-60TSKR1
IC901 8-753-224-50 IC CXP973064-243R
IC902 8-759-649-48 IC SN74AHC1G32DCKR
DMB07
99
HCD-RV777D/RV888D/RV999D
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
IC903 6-704-004-01 IC BR24L16F-WE2
IC904 6-704-753-01 IC SN74AHC2G74HDCUR
IC906 6-700-407-01 IC SM8707GV-G-E2
IC907 8-759-583-47 IC uPC2933T-E2
< JUMPER RESISTOR >
JW392 1-216-864-11 SHORT CHIP 0
JW801 1-218-990-11 SHORT CHIP 0
JW802 1-218-990-11 SHORT CHIP 0
JW803 1-218-990-11 SHORT CHIP 0
JW804 1-218-990-11 SHORT CHIP 0
JW805 1-218-990-11 SHORT CHIP 0
JW806 1-218-990-11 SHORT CHIP 0
L103 1-216-295-11 SHORT CHIP 0
L501 1-216-295-11 SHORT CHIP 0
< COIL >
L704 1-412-031-11 INDUCTOR 47uH
L901 1-412-031-11 INDUCTOR 47uH
< TRANSISTOR >
Q202 8-729-929-26 TRANSISTOR DTC114TE
Q901 8-729-929-26 TRANSISTOR DTC114TE
< RESISTOR >
R10 1-216-801-11 METAL CHIP 22 5% 1/10W
R11 1-216-801-11 METAL CHIP 22 5% 1/10W
R12 1-216-801-11 METAL CHIP 22 5% 1/10W
R13 1-216-801-11 METAL CHIP 22 5% 1/10W
R14 1-216-801-11 METAL CHIP 22 5% 1/10W
R15 1-216-801-11 METAL CHIP 22 5% 1/10W
R213 1-218-939-11 RES-CHIP 68 5% 1/16W
R215 1-216-864-11 SHORT CHIP 0
R217 1-216-864-11 SHORT CHIP 0
R218 1-216-864-11 SHORT CHIP 0 (RV777D)
R219 1-216-864-11 SHORT CHIP 0 (RV888D/RV999D)
R220 1-216-864-11 SHORT CHIP 0
R221 1-216-864-11 SHORT CHIP 0 (RV888D/RV999D)
R222 1-216-864-11 SHORT CHIP 0 (RV888D/RV999D)
R227 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R230 1-216-803-11 METAL CHIP 33 5% 1/10W
R231 1-216-803-11 METAL CHIP 33 5% 1/10W
R232 1-216-803-11 METAL CHIP 33 5% 1/10W
R234 1-216-833-11 METAL CHIP 10K 5% 1/10W
R239 1-216-809-11 METAL CHIP 100 5% 1/10W
(RV777D)
R240 1-216-841-11 METAL CHIP 47K 5% 1/10W
R241 1-216-864-11 SHORT CHIP 0
R244 1-216-821-11 METAL CHIP 1K 5% 1/10W
R245 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R246 1-216-833-11 METAL CHIP 10K 5% 1/10W
R247 1-216-821-11 METAL CHIP 1K 5% 1/10W
R248 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R250 1-216-864-11 SHORT CHIP 0
R251 1-216-864-11 SHORT CHIP 0
R253 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R254 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R255 1-216-864-11 SHORT CHIP 0
R257 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R259 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R260 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R261 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R263 1-218-285-11 METAL CHIP 75 5% 1/10W
R264 1-218-285-11 METAL CHIP 75 5% 1/10W
R265 1-218-285-11 METAL CHIP 75 5% 1/10W
R266 1-218-285-11 METAL CHIP 75 5% 1/10W
R267 1-218-285-11 METAL CHIP 75 5% 1/10W
R268 1-216-864-11 SHORT CHIP 0
R269 1-216-864-11 SHORT CHIP 0
R270 1-216-864-11 SHORT CHIP 0
R271 1-216-809-11 METAL CHIP 100 5% 1/10W
R272 1-216-809-11 METAL CHIP 100 5% 1/10W
R273 1-216-864-11 SHORT CHIP 0
R274 1-216-864-11 SHORT CHIP 0
R275 1-216-864-11 SHORT CHIP 0
R276 1-216-864-11 SHORT CHIP 0
R277 1-216-864-11 SHORT CHIP 0
R278 1-218-285-11 METAL CHIP 75 5% 1/10W
R279 1-218-285-11 METAL CHIP 75 5% 1/10W
R280 1-218-285-11 METAL CHIP 75 5% 1/10W
R281 1-218-285-11 METAL CHIP 75 5% 1/10W
R282 1-218-285-11 METAL CHIP 75 5% 1/10W
R283 1-218-847-11 METAL CHIP 1K 0.5% 1/10W
R284 1-218-829-11 METAL CHIP 180 0.5% 1/10W
R288 1-216-864-11 SHORT CHIP 0 (RV777D)
R290 1-216-809-11 METAL CHIP 100 5% 1/10W
R291 1-216-809-11 METAL CHIP 100 5% 1/10W
R292 1-216-809-11 METAL CHIP 100 5% 1/10W
R301 1-216-821-11 METAL CHIP 1K 5% 1/10W
R302 1-216-813-11 METAL CHIP 220 5% 1/10W
(RV888D/RV999D)
R303 1-216-813-11 METAL CHIP 220 5% 1/10W
(RV888D/RV999D)
R304 1-216-813-11 METAL CHIP 220 5% 1/10W
(RV888D/RV999D)
R305 1-216-813-11 METAL CHIP 220 5% 1/10W
(RV888D/RV999D)
R306 1-216-813-11 METAL CHIP 220 5% 1/10W
(RV888D/RV999D)
R307 1-216-813-11 METAL CHIP 220 5% 1/10W
(RV888D/RV999D)
R308 1-216-813-11 METAL CHIP 220 5% 1/10W
R309 1-216-813-11 METAL CHIP 220 5% 1/10W
R310 1-216-809-11 METAL CHIP 100 5% 1/10W
R311 1-216-809-11 METAL CHIP 100 5% 1/10W
R312 1-216-809-11 METAL CHIP 100 5% 1/10W
R313 1-216-833-11 METAL CHIP 10K 5% 1/10W
(RV888D/RV999D)
R314 1-216-801-11 METAL CHIP 22 5% 1/10W
(RV888D/RV999D)
R320 1-216-864-11 SHORT CHIP 0 (RV777D)
R342 1-216-801-11 METAL CHIP 22 5% 1/10W
(RV777D)
R367 1-216-864-11 SHORT CHIP 0
R368 1-216-864-11 SHORT CHIP 0
R369 1-216-864-11 SHORT CHIP 0
R503 1-216-841-11 METAL CHIP 47K 5% 1/10W
DMB07
100
HCD-RV777D/RV888D/RV999D
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R504 1-216-841-11 METAL CHIP 47K 5% 1/10W
R505 1-216-841-11 METAL CHIP 47K 5% 1/10W
R506 1-216-841-11 METAL CHIP 47K 5% 1/10W
R510 1-216-847-11 METAL CHIP 150K 5% 1/10W
R511 1-216-847-11 METAL CHIP 150K 5% 1/10W
R512 1-216-842-11 METAL CHIP 56K 5% 1/10W
R513 1-216-842-11 METAL CHIP 56K 5% 1/10W
R514 1-216-833-11 METAL CHIP 10K 5% 1/10W
R515 1-216-833-11 METAL CHIP 10K 5% 1/10W
R516 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R517 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R519 1-216-845-11 METAL CHIP 100K 5% 1/10W
R520 1-216-833-11 METAL CHIP 10K 5% 1/10W
R521 1-216-845-11 METAL CHIP 100K 5% 1/10W
R522 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R523 1-216-833-11 METAL CHIP 10K 5% 1/10W
R524 1-216-833-11 METAL CHIP 10K 5% 1/10W
R525 1-216-833-11 METAL CHIP 10K 5% 1/10W
R527 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R529 1-216-839-11 METAL CHIP 33K 5% 1/10W
R530 1-216-842-11 METAL CHIP 56K 5% 1/10W
R533 1-216-839-11 METAL CHIP 33K 5% 1/10W
R534 1-216-842-11 METAL CHIP 56K 5% 1/10W
R536 1-216-833-11 METAL CHIP 10K 5% 1/10W
R537 1-216-843-11 METAL CHIP 68K 5% 1/10W
R545 1-216-833-11 METAL CHIP 10K 5% 1/10W
R548 1-216-833-11 METAL CHIP 10K 5% 1/10W
R550 1-216-821-11 METAL CHIP 1K 5% 1/10W
R551 1-216-821-11 METAL CHIP 1K 5% 1/10W
R552 1-216-821-11 METAL CHIP 1K 5% 1/10W
R555 1-216-864-11 SHORT CHIP 0
R558 1-216-841-11 METAL CHIP 47K 5% 1/10W
R559 1-216-821-11 METAL CHIP 1K 5% 1/10W
R560 1-216-821-11 METAL CHIP 1K 5% 1/10W
R561 1-216-821-11 METAL CHIP 1K 5% 1/10W
R562 1-216-821-11 METAL CHIP 1K 5% 1/10W
R563 1-216-821-11 METAL CHIP 1K 5% 1/10W
R564 1-216-821-11 METAL CHIP 1K 5% 1/10W
R565 1-216-821-11 METAL CHIP 1K 5% 1/10W
R566 1-216-833-11 METAL CHIP 10K 5% 1/10W
R567 1-216-827-11 METAL CHIP 3.3K 5% 1/10W
R568 1-216-857-11 METAL CHIP 1M 5% 1/10W
R571 1-216-857-11 METAL CHIP 1M 5% 1/10W
R572 1-216-853-11 METAL CHIP 470K 5% 1/10W
R573 1-216-833-11 METAL CHIP 10K 5% 1/10W
R577 1-216-864-11 SHORT CHIP 0
R579 1-216-832-11 METAL CHIP 8.2K 5% 1/10W
R580 1-216-839-11 METAL CHIP 33K 5% 1/10W
R581 1-216-834-11 METAL CHIP 12K 5% 1/10W
R582 1-216-864-11 SHORT CHIP 0
R584 1-216-839-11 METAL CHIP 33K 5% 1/10W
R586 1-218-747-11 METAL CHIP 200K 0.5% 1/10W
R587 1-216-864-11 SHORT CHIP 0
R588 1-216-833-11 METAL CHIP 10K 5% 1/10W
R589 1-216-833-11 METAL CHIP 10K 5% 1/10W
R591 1-216-864-11 SHORT CHIP 0
R593 1-216-845-11 METAL CHIP 100K 5% 1/10W
R594 1-216-864-11 SHORT CHIP 0
R599 1-216-821-11 METAL CHIP 1K 5% 1/10W
R601 1-216-864-11 SHORT CHIP 0
R694 1-216-833-11 METAL CHIP 10K 5% 1/10W
R698 1-216-864-11 SHORT CHIP 0
R699 1-216-864-11 SHORT CHIP 0
R700 1-216-832-11 METAL CHIP 8.2K 5% 1/10W
R707 1-216-809-11 METAL CHIP 100 5% 1/10W
R708 1-216-853-11 METAL CHIP 470K 5% 1/10W
R709 1-216-847-11 METAL CHIP 150K 5% 1/10W
R710 1-216-833-11 METAL CHIP 10K 5% 1/10W
R711 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R712 1-216-833-11 METAL CHIP 10K 5% 1/10W
R713 1-216-833-11 METAL CHIP 10K 5% 1/10W
R714 1-216-833-11 METAL CHIP 10K 5% 1/10W
R715 1-216-833-11 METAL CHIP 10K 5% 1/10W
R716 1-216-809-11 METAL CHIP 100 5% 1/10W
R717 1-216-845-11 METAL CHIP 100K 5% 1/10W
R718 1-216-833-11 METAL CHIP 10K 5% 1/10W
R719 1-216-821-11 METAL CHIP 1K 5% 1/10W
R720 1-216-821-11 METAL CHIP 1K 5% 1/10W
R721 1-216-839-11 METAL CHIP 33K 5% 1/10W
R724 1-216-821-11 METAL CHIP 1K 5% 1/10W
R725 1-216-824-11 METAL CHIP 1.8K 5% 1/10W
R726 1-216-845-11 METAL CHIP 100K 5% 1/10W
R727 1-216-827-11 METAL CHIP 3.3K 5% 1/10W
R728 1-216-833-11 METAL CHIP 10K 5% 1/10W
R730 1-216-801-11 METAL CHIP 22 5% 1/10W
R731 1-216-801-11 METAL CHIP 22 5% 1/10W
R732 1-216-833-11 METAL CHIP 10K 5% 1/10W
R733 1-216-833-11 METAL CHIP 10K 5% 1/10W
R734 1-216-833-11 METAL CHIP 10K 5% 1/10W
R735 1-216-833-11 METAL CHIP 10K 5% 1/10W
R736 1-216-833-11 METAL CHIP 10K 5% 1/10W
R737 1-216-833-11 METAL CHIP 10K 5% 1/10W
R738 1-216-833-11 METAL CHIP 10K 5% 1/10W
R741 1-216-801-11 METAL CHIP 22 5% 1/10W
R742 1-216-801-11 METAL CHIP 22 5% 1/10W
R743 1-216-801-11 METAL CHIP 22 5% 1/10W
R744 1-216-801-11 METAL CHIP 22 5% 1/10W
R745 1-216-841-11 METAL CHIP 47K 5% 1/10W
R746 1-216-841-11 METAL CHIP 47K 5% 1/10W
R747 1-216-839-11 METAL CHIP 33K 5% 1/10W
R748 1-216-839-11 METAL CHIP 33K 5% 1/10W
R750 1-216-833-11 METAL CHIP 10K 5% 1/10W
R751 1-216-864-11 SHORT CHIP 0
R758 1-216-864-11 SHORT CHIP 0
R760 1-216-864-11 SHORT CHIP 0
R762 1-216-837-11 METAL CHIP 22K 5% 1/10W
R763 1-216-832-11 METAL CHIP 8.2K 5% 1/10W
R764 1-216-857-11 METAL CHIP 1M 5% 1/10W
R765 1-216-837-11 METAL CHIP 22K 5% 1/10W
R767 1-216-841-11 METAL CHIP 47K 5% 1/10W
R769 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R776 1-216-864-11 SHORT CHIP 0
R777 1-216-864-11 SHORT CHIP 0
R778 1-216-845-11 METAL CHIP 100K 5% 1/10W
R785 1-216-833-11 METAL CHIP 10K 5% 1/10W
R786 1-216-845-11 METAL CHIP 100K 5% 1/10W
DMB07
101
HCD-RV777D/RV888D/RV999D
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R787 1-216-845-11 METAL CHIP 100K 5% 1/10W
R788 1-216-845-11 METAL CHIP 100K 5% 1/10W
R789 1-216-845-11 METAL CHIP 100K 5% 1/10W
R799 1-216-864-11 SHORT CHIP 0
R805 1-216-864-11 SHORT CHIP 0
R901 1-216-801-11 METAL CHIP 22 5% 1/10W
R902 1-216-801-11 METAL CHIP 22 5% 1/10W
R904 1-216-833-11 METAL CHIP 10K 5% 1/10W
R905 1-216-801-11 METAL CHIP 22 5% 1/10W
R906 1-216-801-11 METAL CHIP 22 5% 1/10W
R907 1-216-801-11 METAL CHIP 22 5% 1/10W
R908 1-216-833-11 METAL CHIP 10K 5% 1/10W
R911 1-216-833-11 METAL CHIP 10K 5% 1/10W
R912 1-216-833-11 METAL CHIP 10K 5% 1/10W
R913 1-216-833-11 METAL CHIP 10K 5% 1/10W
R915 1-216-809-11 METAL CHIP 100 5% 1/10W
R916 1-216-821-11 METAL CHIP 1K 5% 1/10W
R917 1-216-821-11 METAL CHIP 1K 5% 1/10W
R918 1-216-801-11 METAL CHIP 22 5% 1/10W
R920 1-216-809-11 METAL CHIP 100 5% 1/10W
R921 1-216-809-11 METAL CHIP 100 5% 1/10W
R922 1-216-801-11 METAL CHIP 22 5% 1/10W
R923 1-216-813-11 METAL CHIP 220 5% 1/10W
R925 1-216-809-11 METAL CHIP 100 5% 1/10W
R926 1-216-809-11 METAL CHIP 100 5% 1/10W
R927 1-216-857-11 METAL CHIP 1M 5% 1/10W
R928 1-216-809-11 METAL CHIP 100 5% 1/10W
R929 1-216-809-11 METAL CHIP 100 5% 1/10W
R930 1-216-809-11 METAL CHIP 100 5% 1/10W
R931 1-216-801-11 METAL CHIP 22 5% 1/10W
R932 1-216-801-11 METAL CHIP 22 5% 1/10W
R933 1-216-801-11 METAL CHIP 22 5% 1/10W
R935 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R936 1-216-809-11 METAL CHIP 100 5% 1/10W
R938 1-216-833-11 METAL CHIP 10K 5% 1/10W
R940 1-216-809-11 METAL CHIP 100 5% 1/10W
R942 1-216-809-11 METAL CHIP 100 5% 1/10W
R943 1-216-809-11 METAL CHIP 100 5% 1/10W
R958 1-216-801-11 METAL CHIP 22 5% 1/10W
R962 1-216-833-11 METAL CHIP 10K 5% 1/10W
R964 1-216-833-11 METAL CHIP 10K 5% 1/10W
R970 1-216-864-11 SHORT CHIP 0
R974 1-216-864-11 SHORT CHIP 0
R975 1-216-833-11 METAL CHIP 10K 5% 1/10W
R978 1-216-833-11 METAL CHIP 10K 5% 1/10W
R984 1-216-833-11 METAL CHIP 10K 5% 1/10W
R988 1-216-864-11 SHORT CHIP 0
R990 1-216-864-11 SHORT CHIP 0
R994 1-216-864-11 SHORT CHIP 0
R995 1-216-864-11 SHORT CHIP 0
R996 1-216-864-11 SHORT CHIP 0
R997 1-216-864-11 SHORT CHIP 0
R998 1-216-864-11 SHORT CHIP 0
R1000 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R1001 1-216-864-11 SHORT CHIP 0 (RV777D)
R1302 1-216-864-11 SHORT CHIP 0
R9980 1-216-864-11 SHORT CHIP 0
R9981 1-216-864-11 SHORT CHIP 0
R9998 1-216-864-11 SHORT CHIP 0
R9999 1-216-864-11 SHORT CHIP 0
< NETWORK RESISTOR >
RB202 1-234-523-21 RES, CHIP NETWORK 0 (3216)
RB203 1-234-523-21 RES, CHIP NETWORK 0 (3216)
RB204 1-234-523-21 RES, CHIP NETWORK 0 (3216)
< VIBRATOR >
X901 1-795-375-11 VIBRATOR, CERAMIC (20MHz)
X902 1-795-630-11 VIBRATOR, CRYSTAL (27MHz)
*************************************************************
1-687-135-12 DRIVER BOARD
*************
< CAPACITOR >
C715 1-126-933-11 ELECT 100uF 20% 16V
C731 1-126-964-11 ELECT 10uF 20% 50V
C735 1-164-159-21 CERAMIC 0.1uF 50V
C736 1-164-159-21 CERAMIC 0.1uF 50V
C737 1-164-159-21 CERAMIC 0.1uF 50V
C741 1-162-306-11 CERAMIC 0.01uF 20% 16V
C751 1-162-306-11 CERAMIC 0.01uF 20% 16V
C752 1-164-159-21 CERAMIC 0.1uF 50V
< CONNECTOR >
CN701 1-785-338-11 PIN, CONNECTOR (LIGHT ANGLE) 12P
CN702 1-784-766-11 CONNECTOR, FFC 5P
*CN703 1-564-720-11 PIN, CONNECTOR (SMALL TYPE) 4P
CN704 1-785-328-11 PIN, CONNECTOR (LIGHT ANGLE) 2P
< DIODE >
D701 8-719-921-42 DIODE MTZJ-5.1A
D711 8-719-109-69 DIODE RD3.6ESB2
< IC >
IC701 8-759-598-69 IC BA6956AN
IC712 8-759-598-69 IC BA6956AN
< TRANSISTOR >
Q731 8-729-029-66 TRANSISTOR DTC114ESA
< RESISTOR >
R701 1-249-413-11 CARBON 470 5% 1/4W
R702 1-247-807-31 CARBON 100 5% 1/4W
R711 1-249-417-11 CARBON 1K 5% 1/4W
R712 1-249-425-11 CARBON 4.7K 5% 1/4W
R713 1-249-433-11 CARBON 22K 5% 1/4W
R721 1-249-425-11 CARBON 4.7K 5% 1/4W
R722 1-249-425-11 CARBON 4.7K 5% 1/4W
R723 1-249-425-11 CARBON 4.7K 5% 1/4W
R731 1-247-807-31 CARBON 100 5% 1/4W
R732 1-249-429-11 CARBON 10K 5% 1/4W
R733 1-249-417-11 CARBON 1K 5% 1/4W
R734 1-249-430-11 CARBON 12K 5% 1/4W
R735 1-247-807-31 CARBON 100 5% 1/4W
R751 1-249-425-11 CARBON 4.7K 5% 1/4W
*************************************************************
DMB07 DRIVER
102
HCD-RV777D/RV888D/RV999D
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
A-1053-978-A FRONT AMP BOARD, COMPLETE (RV888D)
A-4751-854-A FRONT AMP BOARD, COMPLETE (RV999D)
A-4751-856-A FRONT AMP BOARD, COMPLETE (RV777D)
***************************
7-685-872-09 SCREW +BVTT 3X8 (S)
< CAPACITOR >
C201 1-126-964-11 ELECT 10uF 20% 50V
C202 1-162-302-11 CERAMIC 0.0022uF 20% 16V
C203 1-162-286-31 CERAMIC 220PF 10% 50V
C204 1-126-967-11 ELECT 47uF 20% 50V
(RV777D)
C204 1-126-968-11 ELECT 100uF 20% 50V
(RV888D/RV999D)
C206 1-136-495-11 FILM 0.068uF 5% 50V
C207 1-136-495-11 FILM 0.068uF 5% 50V
C208 1-128-576-11 ELECT 100uF 20% 63V
C216 1-162-306-11 CERAMIC 0.01uF 20% 16V
C221 1-126-971-11 ELECT 470uF 20% 50V
C251 1-126-964-11 ELECT 10uF 20% 50V
C252 1-162-302-11 CERAMIC 0.0022uF 20% 16V
C253 1-162-286-31 CERAMIC 220PF 10% 50V
C254 1-126-967-11 ELECT 47uF 20% 50V
(RV777D)
C254 1-126-968-11 ELECT 100uF 20% 50V
(RV888D/RV999D)
C256 1-136-495-11 FILM 0.068uF 5% 50V
C257 1-136-495-11 FILM 0.068uF 5% 50V
C258 1-128-576-11 ELECT 100uF 20% 63V
C271 1-135-928-21 ELECT 2200uF 20% 63V
C272 1-135-928-21 ELECT 2200uF 20% 63V
C273 1-130-777-00 MYLAR 0.1uF 5% 100V
C274 1-130-777-00 MYLAR 0.1uF 5% 100V
C281 1-136-497-81 FILM 0.1uF 5% 50V
C282 1-136-497-81 FILM 0.1uF 5% 50V
C283 1-136-497-81 FILM 0.1uF 5% 50V
C284 1-136-497-81 FILM 0.1uF 5% 50V
C285 1-162-306-11 CERAMIC 0.01uF 20% 16V
C286 1-162-306-11 CERAMIC 0.01uF 20% 16V
C921 1-126-956-11 ELECT 0.1uF 20% 50V
C922 1-126-767-11 ELECT 1000uF 20% 16V
C923 1-126-956-11 ELECT 0.1uF 20% 50V
C924 1-126-767-11 ELECT 1000uF 20% 16V
C925 1-126-956-11 ELECT 0.1uF 20% 50V
C926 1-126-933-11 ELECT 100uF 20% 16V
C933 1-126-956-11 ELECT 0.1uF 20% 50V
C934 1-126-925-11 ELECT 470uF 20% 10V
C937 1-126-956-11 ELECT 0.1uF 20% 50V
C938 1-126-925-11 ELECT 470uF 20% 10V
< CONNECTOR >
CN201 1-573-829-11 CONNECTOR, BOARD TO BOARD 15P
CN206 1-573-829-11 CONNECTOR, BOARD TO BOARD 15P
< DIODE >
D201 8-719-991-33 DIODE 1SS133T-77
D251 8-719-991-33 DIODE 1SS133T-77
D271 8-719-510-68 DIODE D5SBA204101
D281 8-719-991-33 DIODE 1SS133T-77
D291 8-719-991-33 DIODE 1SS133T-77
< IC >
IC201 6-705-853-01 IC STK403-120
< COIL >
L281 1-422-009-13 COIL, AIR-CORE
L282 1-422-009-13 COIL, AIR-CORE
< TRANSISTOR >
Q201 8-729-140-84 TRANSISTOR 2SC1841-PAFAEA
Q216 8-729-140-84 TRANSISTOR 2SC1841-PAFAEA
Q217 8-729-119-78 TRANSISTOR 2SC2785-HFE
Q221 8-729-140-82 TRANSISTOR 2SA988-PAFAEA
Q222 8-729-140-84 TRANSISTOR 2SC1841-PAFAEA
Q251 8-729-140-84 TRANSISTOR 2SC1841-PAFAEA
Q281 8-729-026-39 TRANSISTOR 2SA933AS-QT
Q282 8-729-140-84 TRANSISTOR 2SC1841-PAFAEA
< RESISTOR >
R201 1-247-831-11 CARBON 1K 5% 1/4W
R202 1-247-871-11 CARBON 47K 5% 1/4W
R203 1-247-807-31 CARBON 100 5% 1/4W
(RV888D/RV999D)
R203 1-249-409-11 CARBON 220 5% 1/4W
(RV777D)
R204 1-247-871-11 CARBON 47K 5% 1/4W
0R205 1-245-235-21 METAL 0.22 10% 2W F
0R206 1-245-235-21 METAL 0.22 10% 2W F
R207 1-247-831-11 CARBON 1K 5% 1/4W
R208 1-249-431-11 CARBON 15K 5% 1/4W
R209 1-247-879-11 CARBON 100K 5% 1/4W
R210 1-260-076-11 CARBON 10 5% 1/2W F
0R211 1-212-881-11 FUSIBLE 100 5% 1/4W F
R213 1-247-831-11 CARBON 1K 5% 1/4W
R214 1-247-831-11 CARBON 1K 5% 1/4W
R215 1-247-863-11 CARBON 22K 5% 1/4W
R216 1-247-879-11 CARBON 100K 5% 1/4W
R217 1-249-429-11 CARBON 10K 5% 1/4W
R218 1-247-871-11 CARBON 47K 5% 1/4W
0R219 1-202-972-61 FUSIBLE 1 5% 1/4W F
0R220 1-202-972-61 FUSIBLE 1 5% 1/4W F
R221 1-249-421-11 CARBON 2.2K 5% 1/4W
R222 1-247-863-11 CARBON 22K 5% 1/4W
R223 1-249-429-11 CARBON 10K 5% 1/4W
R224 1-249-429-11 CARBON 10K 5% 1/4W
R225 1-249-439-11 CARBON 68K 5% 1/4W
R226 1-249-426-11 CARBON 5.6K 5% 1/4W
R239 1-247-871-11 CARBON 47K 5% 1/4W
R240 1-247-873-11 CARBON 56K 5% 1/4W
R251 1-247-831-11 CARBON 1K 5% 1/4W
R252 1-247-871-11 CARBON 47K 5% 1/4W
R253 1-247-807-31 CARBON 100 5% 1/4W
(RV888D/RV999D)
R253 1-249-409-11 CARBON 220 5% 1/4W
(RV777D)
R254 1-247-871-11 CARBON 47K 5% 1/4W
FRONT AMP
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
103
HCD-RV777D/RV888D/RV999D
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
0R255 1-245-235-21 METAL 0.22 10% 2W F
0R256 1-245-235-21 METAL 0.22 10% 2W F
R257 1-247-831-11 CARBON 1K 5% 1/4W
R258 1-249-431-11 CARBON 15K 5% 1/4W
R259 1-247-879-11 CARBON 100K 5% 1/4W
R260 1-260-076-11 CARBON 10 5% 1/2W F
0R261 1-212-881-11 FUSIBLE 100 5% 1/4W F
R271 1-247-879-11 CARBON 100K 5% 1/4W
R272 1-247-879-11 CARBON 100K 5% 1/4W
0R280 1-216-456-00 METAL OXIDE 820 5% 2W F
(RV888D/RV999D)
0R280 1-216-457-00 METAL OXIDE 1.2K 5% 2W F
(RV777D)
R281 1-260-076-11 CARBON 10 5% 1/2W F
R282 1-260-076-11 CARBON 10 5% 1/2W F
R283 1-260-076-11 CARBON 10 5% 1/2W F
R284 1-260-076-11 CARBON 10 5% 1/2W F
R285 1-247-871-11 CARBON 47K 5% 1/4W
R286 1-247-871-11 CARBON 47K 5% 1/4W
R287 1-249-429-11 CARBON 10K 5% 1/4W
R288 1-247-871-11 CARBON 47K 5% 1/4W
R289 1-249-429-11 CARBON 10K 5% 1/4W
R290 1-249-429-11 CARBON 10K 5% 1/4W
R924 1-247-831-11 CARBON 1K 5% 1/4W
< RELAY >
RY281 1-515-920-11 RELAY
< THERMISTOR >
TH201 1-807-796-11 THERMISTOR
< TERMINAL BOARD >
TM201 1-694-677-12 TERMINAL BOARD (4P) (FRONT SPEAKER)
*************************************************************
HP BOARD
*********
< JUMPER RESISTOR >
C500 1-216-864-11 SHORT CHIP 0
< CONNECTOR >
*CN503 1-564-720-11 PIN, CONNECTOR (SMALL TYPE) 4P
< JACK >
J502 1-794-702-11 JACK, HEADPHONE (PHONES)
< RESISTOR >
R531 1-260-083-11 CARBON 47 5% 1/2W F
R532 1-260-083-11 CARBON 47 5% 1/2W F
*************************************************************
A-1053-972-A JACK BOARD, COMPLETE (RV999D:E51,AR,MX)
A-4751-845-A JACK BOARD, COMPLETE
(EXCEPT RV999D:E51,AR,MX)
*********************
< CAPACITOR >
C501 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C502 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C503 1-162-953-11 CERAMIC CHIP 100PF 5% 50V
C504 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C507 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C508 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C509 1-107-726-11 CERAMIC CHIP 0.01uF 10% 16V
C510 1-115-868-11 ELECT 0.22uF 20% 50V
C511 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C512 1-162-949-11 CERAMIC CHIP 47PF 5% 50V
C513 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
C514 1-115-867-11 ELECT 0.1uF 20% 50V
C515 1-115-872-11 ELECT 2.2uF 20% 50V
C516 1-162-949-11 CERAMIC CHIP 47PF 5% 50V
C517 1-162-955-11 CERAMIC CHIP 150PF 5% 50V
C518 1-115-872-11 ELECT 2.2uF 20% 50V
C519 1-126-791-11 ELECT 10uF 20% 35V
C520 1-126-786-11 ELECT 47uF 20% 16V
C521 1-126-786-11 ELECT 47uF 20% 16V
C522 1-115-871-11 ELECT 1uF 20% 50V
(EXCEPT RV999D:E51,AR,MX)
C523 1-162-969-11 CERAMIC CHIP 0.0068uF 10% 25V
(EXCEPT RV999D:E51,AR,MX)
C524 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
(EXCEPT RV999D:E51,AR,MX)
C525 1-110-563-11 CERAMIC CHIP 0.068uF 10% 16V
(EXCEPT RV999D:E51,AR,MX)
C526 1-115-870-11 ELECT 0.47uF 20% 50V
(EXCEPT RV999D:E51,AR,MX)
C527 1-115-870-11 ELECT 0.47uF 20% 50V
(EXCEPT RV999D:E51,AR,MX)
C528 1-131-664-11 CERAMIC CHIP 0.15uF 10% 10V
(EXCEPT RV999D:E51,AR,MX)
C529 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
(EXCEPT RV999D:E51,AR,MX)
C530 1-162-969-11 CERAMIC CHIP 0.0068uF 10% 25V
(EXCEPT RV999D:E51,AR,MX)
C531 1-110-563-11 CERAMIC CHIP 0.068uF 10% 16V
(EXCEPT RV999D:E51,AR,MX)
C532 1-126-785-11 ELECT 47uF 20% 10V
(EXCEPT RV999D:E51,AR,MX)
C533 1-126-785-11 ELECT 47uF 20% 10V
(EXCEPT RV999D:E51,AR,MX)
C534 1-115-871-11 ELECT 1uF 20% 50V
(EXCEPT RV999D:E51,AR,MX)
C535 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V
(EXCEPT RV999D:E51,AR,MX)
C536 1-115-872-11 ELECT 2.2uF 20% 50V
(EXCEPT RV999D:E51,AR,MX)
< DIODE >
D501 8-719-988-61 DIODE 1SS355TE-17
D502 8-719-988-61 DIODE 1SS355TE-17
D505 8-719-988-61 DIODE 1SS355TE-17
D506 8-719-988-61 DIODE 1SS355TE-17
FRONT AMP
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
JACKHP
104
HCD-RV777D/RV888D/RV999D
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
D507 8-719-988-61 DIODE 1SS355TE-17
D508 8-719-988-61 DIODE 1SS355TE-17
D1201 8-719-069-54 DIODE UDZSTE-175.1B
(EXCEPT RV999D:E51,AR,MX)
< GROUND TERMINAL BOARD >
EPT501 1-537-771-21 TERMINAL BOARD, GROUND
EPT502 1-537-771-21 TERMINAL BOARD, GROUND
< FERRITE BEAD >
FB505 1-469-869-21 INDUCTOR (EMI FERRITE) (2012)
< IC >
IC501 8-759-710-97 IC NJM4565M-D
IC502 8-759-496-41 IC M65850FP-E1
(EXCEPT RV999D:E51,AR,MX)
< JACK >
J501 1-764-592-11 JACK, 3P (GAME INPUT)
J503 1-770-226-11 JACK (LARGE TYPE) (MIC)
< RESISTOR >
R501 1-216-821-11 METAL CHIP 1K 5% 1/10W
R502 1-216-821-11 METAL CHIP 1K 5% 1/10W
R503 1-216-841-11 METAL CHIP 47K 5% 1/10W
R504 1-216-841-11 METAL CHIP 47K 5% 1/10W
R505 1-216-833-11 METAL CHIP 10K 5% 1/10W
R506 1-216-833-11 METAL CHIP 10K 5% 1/10W
R507 1-216-821-11 METAL CHIP 1K 5% 1/10W
R508 1-216-835-11 METAL CHIP 15K 5% 1/10W
R509 1-216-821-11 METAL CHIP 1K 5% 1/10W
R510 1-216-837-11 METAL CHIP 22K 5% 1/10W
R511 1-216-809-11 METAL CHIP 100 5% 1/10W
R512 1-216-833-11 METAL CHIP 10K 5% 1/10W
R513 1-216-847-11 METAL CHIP 150K 5% 1/10W
R514 1-216-809-11 METAL CHIP 100 5% 1/10W
R515 1-216-845-11 METAL CHIP 100K 5% 1/10W
R516 1-216-813-11 METAL CHIP 220 5% 1/10W
R517 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R518 1-216-830-11 METAL CHIP 5.6K 5% 1/10W
R519 1-216-837-11 METAL CHIP 22K 5% 1/10W
(EXCEPT RV999D:E51,AR,MX)
R520 1-216-837-11 METAL CHIP 22K 5% 1/10W
(EXCEPT RV999D:E51,AR,MX)
R521 1-216-837-11 METAL CHIP 22K 5% 1/10W
(EXCEPT RV999D:E51,AR,MX)
R522 1-216-841-11 METAL CHIP 47K 5% 1/10W
(EXCEPT RV999D:E51,AR,MX)
R523 1-216-837-11 METAL CHIP 22K 5% 1/10W
(EXCEPT RV999D:E51,AR,MX)
R524 1-216-837-11 METAL CHIP 22K 5% 1/10W
(EXCEPT RV999D:E51,AR,MX)
R525 1-216-837-11 METAL CHIP 22K 5% 1/10W
(EXCEPT RV999D:E51,AR,MX)
R526 1-216-846-11 METAL CHIP 120K 5% 1/10W
(EXCEPT RV999D:E51,AR,MX)
R527 1-216-814-11 METAL CHIP 270 5% 1/10W
(EXCEPT RV999D:E51,AR,MX)
R528 1-216-835-11 METAL CHIP 15K 5% 1/10W
(EXCEPT RV999D:E51,AR,MX)
R529 1-216-835-11 METAL CHIP 15K 5% 1/10W
(EXCEPT RV999D:E51,AR,MX)
< VARIABLE RESISTOR >
RV501 1-223-983-11 RES, VAR, CARBON 50K (MIC LEVEL)
RV502 1-223-983-11 RES, VAR, CARBON 50K (ECHO LEVEL)
(EXCEPT RV999D:E51,AR,MX)
*************************************************************
A-1053-866-A MAIN BOARD, COMPLETE (RV999D:SP,MY,PH)
A-1053-867-A MAIN BOARD, COMPLETE (RV999D:EA)
A-1053-868-A MAIN BOARD, COMPLETE (RV999D:AUS)
A-1053-869-A MAIN BOARD, COMPLETE
(RV999D:E51,AR,MX)
A-1053-871-A MAIN BOARD, COMPLETE (RV888D:SP,MY)
A-1053-872-A MAIN BOARD, COMPLETE (RV888D:EA)
A-1053-873-A MAIN BOARD, COMPLETE (RV888D:AUS)
A-1053-875-A MAIN BOARD, COMPLETE (RV777D:SP,MY,PH)
A-1053-876-A MAIN BOARD, COMPLETE (RV777D:EA)
A-4751-800-A MAIN BOARD, COMPLETE (RV999D:E3,E15)
A-4751-804-A MAIN BOARD, COMPLETE (RV888D:E3,E15)
A-4751-806-A MAIN BOARD, COMPLETE (RV777D:E3,E15)
*********************
< CAPACITOR >
C101 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C102 1-126-382-11 ELECT 100uF 20% 16V
C103 1-104-658-11 ELECT 100uF 20% 10V
C104 1-104-658-11 ELECT 100uF 20% 10V
C105 1-104-658-11 ELECT 100uF 20% 10V
C111 1-126-964-11 ELECT 10uF 20% 50V
C112 1-126-961-11 ELECT 2.2uF 20% 50V
C113 1-126-961-11 ELECT 2.2uF 20% 50V
C114 1-126-961-11 ELECT 2.2uF 20% 50V
C115 1-115-872-11 ELECT 2.2uF 20% 50V
C117 1-126-961-11 ELECT 2.2uF 20% 50V
C118 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V
C119 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V
C120 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V
C121 1-126-964-11 ELECT 10uF 20% 50V
C122 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C123 1-126-795-11 ELECT 10uF 20% 50V
C124 1-137-194-81 FILM 0.47uF 5% 50V
C125 1-137-194-81 FILM 0.47uF 5% 50V
C126 1-115-871-11 ELECT 1uF 20% 50V
C127 1-126-964-11 ELECT 10uF 20% 50V
C132 1-115-871-11 ELECT 1uF 20% 50V
C133 1-136-497-81 FILM 0.1uF 5% 50V
(RV777D)
C134 1-137-190-11 FILM 0.22uF 5% 50V
(RV777D)
C135 1-126-795-11 ELECT 10uF 20% 50V
C136 1-136-161-00 FILM 0.047uF 5% 50V
C137 1-126-964-11 ELECT 10uF 20% 50V
C141 1-126-964-11 ELECT 10uF 20% 50V
C142 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C143 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
JACK MAIN
105
HCD-RV777D/RV888D/RV999D
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
C145 1-110-518-11 ELECT 10uF 20% 100V
C151 1-126-964-11 ELECT 10uF 20% 50V
C152 1-126-961-11 ELECT 2.2uF 20% 50V
C153 1-126-961-11 ELECT 2.2uF 20% 50V
C154 1-126-961-11 ELECT 2.2uF 20% 50V
C155 1-115-872-11 ELECT 2.2uF 20% 50V
C156 1-126-961-11 ELECT 2.2uF 20% 50V
C157 1-126-961-11 ELECT 2.2uF 20% 50V
C158 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V
C159 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V
C160 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V
C161 1-126-964-11 ELECT 10uF 20% 50V
C162 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C163 1-126-964-11 ELECT 10uF 20% 50V
C164 1-137-194-81 FILM 0.47uF 5% 50V
C165 1-137-194-81 FILM 0.47uF 5% 50V
C166 1-115-871-11 ELECT 1uF 20% 50V
C167 1-126-964-11 ELECT 10uF 20% 50V
C171 1-115-870-11 ELECT 0.47uF 20% 50V
C172 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C181 1-126-964-11 ELECT 10uF 20% 50V
C182 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C183 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C185 1-110-518-11 ELECT 10uF 20% 100V
C191 1-126-933-11 ELECT 100uF 20% 16V
C192 1-126-964-11 ELECT 10uF 20% 50V
C193 1-126-960-11 ELECT 1uF 20% 50V
C201 1-216-864-11 SHORT CHIP 0
C202 1-216-864-11 SHORT CHIP 0
C231 1-126-964-11 ELECT 10uF 20% 50V
C232 1-104-658-11 ELECT 100uF 20% 10V
C233 1-126-961-11 ELECT 2.2uF 20% 50V
C234 1-104-658-11 ELECT 100uF 20% 10V
C235 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C271 1-126-964-11 ELECT 10uF 20% 50V
C272 1-126-964-11 ELECT 10uF 20% 50V
(RV888D/RV999D)
C301 1-126-964-11 ELECT 10uF 20% 50V
(RV888D/RV999D)
C302 1-162-960-11 CERAMIC CHIP 220PF 10% 50V
(RV888D/RV999D)
C303 1-162-960-11 CERAMIC CHIP 220PF 10% 50V
(RV888D/RV999D)
C304 1-126-964-11 ELECT 10uF 20% 50V
(RV888D/RV999D)
C305 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
(RV888D/RV999D)
C306 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
(RV888D/RV999D)
C307 1-126-964-11 ELECT 10uF 20% 50V
(RV888D/RV999D)
C308 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C309 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C310 1-126-964-11 ELECT 10uF 20% 50V
C311 1-126-960-11 ELECT 1uF 20% 50V
C312 1-126-964-11 ELECT 10uF 20% 50V
(RV888D/RV999D)
C313 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10V
(RV888D/RV999D)
C314 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10V
(RV888D/RV999D)
C320 1-126-964-11 ELECT 10uF 20% 50V
(RV888D/RV999D)
C321 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
(RV888D/RV999D)
C322 1-126-964-11 ELECT 10uF 20% 50V
(RV888D/RV999D)
C323 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
(RV888D/RV999D)
C324 1-126-964-11 ELECT 10uF 20% 50V
(RV888D/RV999D)
C325 1-126-964-11 ELECT 10uF 20% 50V
(RV888D/RV999D)
C330 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V
(RV888D/RV999D)
C331 1-126-960-11 ELECT 1uF 20% 50V
(RV888D/RV999D)
C332 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10V
(RV888D/RV999D)
C333 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
(RV888D/RV999D)
C334 1-126-964-11 ELECT 10uF 20% 50V
(RV888D/RV999D)
C335 1-126-964-11 ELECT 10uF 20% 50V
C337 1-126-964-11 ELECT 10uF 20% 50V
(RV888D/RV999D)
C338 1-126-964-11 ELECT 10uF 20% 50V
(RV888D/RV999D)
C341 1-126-933-11 ELECT 100uF 20% 16V
C342 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C343 1-126-960-11 ELECT 1uF 20% 50V
C344 1-126-933-11 ELECT 100uF 20% 16V
C345 1-126-933-11 ELECT 100uF 20% 16V
C347 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C351 1-126-964-11 ELECT 10uF 20% 50V
(RV888D/RV999D)
C352 1-162-960-11 CERAMIC CHIP 220PF 10% 50V
(RV888D/RV999D)
C353 1-162-960-11 CERAMIC CHIP 220PF 10% 50V
(RV888D/RV999D)
C354 1-126-964-11 ELECT 10uF 20% 50V
(RV888D/RV999D)
C355 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
(RV888D/RV999D)
C356 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
(RV888D/RV999D)
C357 1-126-964-11 ELECT 10uF 20% 50V
(RV888D/RV999D)
C358 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C359 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C360 1-126-964-11 ELECT 10uF 20% 50V
C361 1-126-960-11 ELECT 1uF 20% 50V
C363 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10V
(RV888D/RV999D)
C364 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10V
(RV888D/RV999D)
C365 1-126-964-11 ELECT 10uF 20% 50V
(RV888D/RV999D)
C367 1-126-964-11 ELECT 10uF 20% 50V
(RV888D/RV999D)
MAIN
106
HCD-RV777D/RV888D/RV999D
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
C368 1-126-964-11 ELECT 10uF 20% 50V
(RV888D/RV999D)
C371 1-126-964-11 ELECT 10uF 20% 50V
C372 1-126-964-11 ELECT 10uF 20% 50V
(RV888D/RV999D)
C562 1-164-156-11 CERAMIC CHIP 0.1uF 25V
(RV777D)
C563 1-126-923-11 ELECT 220uF 20% 10V
(RV777D)
C601 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
C602 1-164-245-11 CERAMIC CHIP 0.015uF 10% 25V
C603 1-136-155-00 FILM 0.015uF 5% 50V
C604 1-137-194-81 FILM 0.47uF 5% 50V
C605 1-106-375-12 MYLAR 0.022uF 5% 200V
C607 1-126-794-11 ELECT 4.7uF 20% 50V
C611 1-162-963-11 CERAMIC CHIP 680PF 10% 50V
C612 1-126-794-11 ELECT 4.7uF 20% 50V
C613 1-162-963-11 CERAMIC CHIP 680PF 10% 50V
C614 1-126-794-11 ELECT 4.7uF 20% 50V
C615 1-137-150-11 FILM 0.01uF 5% 100V
C616 1-126-947-11 ELECT 47uF 20% 35V
C617 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C618 1-126-961-11 ELECT 2.2uF 20% 50V
C619 1-126-956-11 ELECT 0.1uF 20% 50V
C620 1-126-960-11 ELECT 1uF 20% 50V
C621 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C622 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C623 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C624 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C651 1-162-963-11 CERAMIC CHIP 680PF 10% 50V
C652 1-126-794-11 ELECT 4.7uF 20% 50V
C653 1-162-963-11 CERAMIC CHIP 680PF 10% 50V
C654 1-126-794-11 ELECT 4.7uF 20% 50V
C655 1-137-150-11 FILM 0.01uF 5% 100V
C656 1-126-947-11 ELECT 47uF 20% 35V
C657 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C658 1-126-961-11 ELECT 2.2uF 20% 50V
C659 1-126-956-11 ELECT 0.1uF 20% 50V
C661 1-164-217-11 CERAMIC CHIP 150PF 5% 50V
C662 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C663 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C664 1-126-964-11 ELECT 10uF 20% 50V
C665 1-126-947-11 ELECT 47uF 20% 35V
C666 1-136-177-00 FILM 1uF 5% 50V
C713 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C714 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C715 1-126-964-11 ELECT 10uF 20% 50V
C719 1-126-794-11 ELECT 4.7uF 20% 50V
C723 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C724 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V
C726 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V
C734 1-136-153-00 FILM 0.01uF 5% 50V
C735 1-136-153-00 FILM 0.01uF 5% 50V
C738 1-119-939-51 ELECT 6800uF 20% 35V
C739 1-126-961-11 ELECT 2.2uF 20% 50V
C740 1-111-235-61 ELECT 10000uF 20% 25V
C752 1-136-153-00 FILM 0.01uF 5% 50V
C753 1-136-153-00 FILM 0.01uF 5% 50V
C772 1-107-696-11 ELECT 47uF 20% 16V
(RV888D/RV999D)
C773 1-107-696-11 ELECT 47uF 20% 16V
(RV888D/RV999D)
C774 1-107-696-11 ELECT 47uF 20% 16V
C775 1-107-696-11 ELECT 47uF 20% 16V
C791 1-126-963-11 ELECT 4.7uF 20% 50V
C810 1-162-918-11 CERAMIC CHIP 18PF 5% 50V
C811 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C813 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C814 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C815 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C816 1-104-655-11 ELECT 470uF 20% 6.3V
C817 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C821 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C862 1-104-655-11 ELECT 470uF 20% 6.3V
C863 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C897 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C898 1-126-964-11 ELECT 10uF 20% 50V
C899 1-162-974-11 CERAMIC CHIP 0.01uF 50V
< CONNECTOR >
CN102 1-568-830-11 CONNECTOR, FFC 11P
CN301 1-779-281-11 CONNECTOR, FFC (LIF(NON-ZIF)) 13P
(RV777D)
CN301 1-779-293-11 CONNECTOR, FFC (LIF(NON-ZIF)) 25P
(RV888D/RV999D)
CN543 1-785-324-11 PIN, CONNECTOR (STRAIGHT) 12P
*CN602 1-564-705-11 PIN, CONNECTOR (SMALL TYPE) 3P
*CN603 1-564-710-11 PIN, CONNECTOR (SMALL TYPE) 8P
CN605 1-784-774-11 CONNECTOR, FFC 13P
*CN704 1-564-518-11 PLUG, CONNECTOR 3P
CN705 1-573-847-11 CONNECTOR, BOARD TO BOARD 15P
CN706 1-784-776-11 CONNECTOR, FFC 15P
CN707 1-573-847-11 CONNECTOR, BOARD TO BOARD 15P
CN901 1-564-707-11 PIN, CONNECTOR (SMALL TYPE) 5P
(RV888D/RV999D)
CN902 1-785-319-11 PIN, CONNECTOR (STRAIGHT) 7P
< DIODE >
D101 8-719-988-61 DIODE 1SS355TE-17
D102 8-719-988-61 DIODE 1SS355TE-17
D171 8-719-988-61 DIODE 1SS355TE-17
D192 8-719-988-61 DIODE 1SS355TE-17
D193 8-719-988-61 DIODE 1SS355TE-17
D194 8-719-988-61 DIODE 1SS355TE-17
D201 8-719-988-61 DIODE 1SS355TE-17
D202 8-719-988-61 DIODE 1SS355TE-17
D230 8-719-988-61 DIODE 1SS355TE-17
D231 8-719-988-61 DIODE 1SS355TE-17
D609 8-719-988-61 DIODE 1SS355TE-17
D610 8-719-988-61 DIODE 1SS355TE-17
D611 8-719-988-61 DIODE 1SS355TE-17
D703 8-719-988-61 DIODE 1SS355TE-17
D704 8-719-988-61 DIODE 1SS355TE-17
D705 8-719-988-61 DIODE 1SS355TE-17
D706 8-719-988-61 DIODE 1SS355TE-17
D707 8-719-058-24 DIODE RB501V-40TE-17
D708 8-719-988-61 DIODE 1SS355TE-17
MAIN
107
HCD-RV777D/RV888D/RV999D
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
D709 8-719-988-61 DIODE 1SS355TE-17
D710 8-719-988-61 DIODE 1SS355TE-17
D711 8-719-988-61 DIODE 1SS355TE-17
D712 8-719-988-61 DIODE 1SS355TE-17
D714 6-500-522-21 DIODE 10EDB40-TB3
D716 8-719-069-56 DIODE UDZSTE-176.2B
D717 8-719-069-56 DIODE UDZSTE-176.2B
D729 8-719-085-36 DIODE 11EQS04-TB5
D732 8-719-028-23 DIODE D3SBA20-4101
D733 8-719-028-23 DIODE D3SBA20-4101
D734 8-719-988-61 DIODE 1SS355TE-17
D735 8-719-988-61 DIODE 1SS355TE-17
D804 8-719-988-61 DIODE 1SS355TE-17
D809 8-719-988-61 DIODE 1SS355TE-17
D810 8-719-988-61 DIODE 1SS355TE-17 (RV888D/RV999D)
D811 8-719-988-61 DIODE 1SS355TE-17
D812 8-719-988-61 DIODE 1SS355TE-17 (RV888D/RV999D)
D813 8-719-988-61 DIODE 1SS355TE-17
< GROUND TERMINAL BOARD >
EPT701 1-537-771-21 TERMINAL BOARD, GROUND
< FERRITE BEAD >
FB561 1-500-445-21 FERRITE, EMI (SMD) (2012) (RV777D)
FB801 1-500-445-21 FERRITE, EMI (SMD) (2012)
< JUMPER RESISTOR >
FB862 1-216-864-11 SHORT CHIP 0
FB899 1-216-864-11 SHORT CHIP 0
< IC >
IC101 6-705-667-01 IC M61537FP-RF0G
IC203 6-703-610-01 IC RT8H015C-T112-1
IC301 6-703-651-11 IC M61530FP-D60G (RV888D/RV999D)
IC302 8-749-019-25 IC TOTX141 (DVD DIGITAL OUT) (RV777D)
IC303 8-759-697-21 IC NJM4565V(TE2) (RV777D)
IC701 6-804-222-01 IC M30620MCN-A38FPU0
IC703 8-759-532-64 IC M62703SL-TP
< JACK >
J102 1-774-785-11 JACK, PIN 1P (SUB WOOFER OUT)
J104 1-816-918-11 JACK, PIN 4P (VIDEO/SAT)
< JUMPER RESISTOR >
JR3 1-216-864-11 SHORT CHIP 0
JR4 1-216-864-11 SHORT CHIP 0 (RV888D/RV999D)
JR5 1-216-864-11 SHORT CHIP 0 (RV888D/RV999D)
JR6 1-216-864-11 SHORT CHIP 0
JR8 1-216-864-11 SHORT CHIP 0
JR9 1-216-864-11 SHORT CHIP 0
JR10 1-216-864-11 SHORT CHIP 0 (RV888D/RV999D)
JR11 1-216-864-11 SHORT CHIP 0
JR12 1-216-864-11 SHORT CHIP 0
JR13 1-216-864-11 SHORT CHIP 0
JR14 1-216-864-11 SHORT CHIP 0
JR15 1-216-864-11 SHORT CHIP 0
JR16 1-216-864-11 SHORT CHIP 0
JR17 1-216-864-11 SHORT CHIP 0
JR104 1-216-837-11 METAL CHIP 22K 5% 1/10W
JR105 1-216-837-11 METAL CHIP 22K 5% 1/10W
JR110 1-216-864-11 SHORT CHIP 0 (RV777D)
JR601 1-216-864-11 SHORT CHIP 0
JR602 1-216-864-11 SHORT CHIP 0
JR603 1-216-864-11 SHORT CHIP 0
< COIL >
L341 1-412-064-11 INDUCTOR 100uH
L561 1-408-619-31 INDUCTOR 220uH (RV777D)
< TRANSISTOR >
Q111 8-729-905-35 TRANSISTOR 2SC4081-R
Q112 8-729-905-35 TRANSISTOR 2SC4081-R
Q142 8-729-021-15 TRANSISTOR 2SD2351T106W
Q143 8-729-021-15 TRANSISTOR 2SD2351T106W
Q151 8-729-905-35 TRANSISTOR 2SC4081-R
Q152 8-729-905-35 TRANSISTOR 2SC4081-R
Q171 8-729-021-15 TRANSISTOR 2SD2351T106W
Q172 8-729-021-15 TRANSISTOR 2SD2351T106W
Q182 8-729-021-15 TRANSISTOR 2SD2351T106W
Q183 8-729-021-15 TRANSISTOR 2SD2351T106W
Q191 8-729-905-35 TRANSISTOR 2SC4081-R
Q232 8-729-905-35 TRANSISTOR 2SC4081-R
Q233 8-729-905-35 TRANSISTOR 2SC4081-R
Q234 8-729-905-35 TRANSISTOR 2SC4081-R
Q373 8-729-021-15 TRANSISTOR 2SD2351T106W
(RV888D/RV999D)
Q374 8-729-021-15 TRANSISTOR 2SD2351T106W
(RV888D/RV999D)
Q375 8-729-021-15 TRANSISTOR 2SD2351T106W
(RV888D/RV999D)
Q377 8-729-021-15 TRANSISTOR 2SD2351T106W
Q601 8-729-142-46 TRANSISTOR 2SC2001-LK
Q602 6-550-044-01 TRANSISTOR 2SB1689-T106
Q603 8-729-905-35 TRANSISTOR 2SC4081-R
Q604 8-729-905-35 TRANSISTOR 2SC4081-R
Q605 8-729-028-73 TRANSISTOR DTA114EUA-T106
Q606 8-729-907-00 TRANSISTOR DTC114EU
Q607 8-729-028-73 TRANSISTOR DTA114EUA-T106
Q608 8-729-907-00 TRANSISTOR DTC114EU
Q613 6-550-044-01 TRANSISTOR 2SB1689-T106
Q614 8-729-907-00 TRANSISTOR DTC114EU
Q615 8-729-907-00 TRANSISTOR DTC114EU
Q616 6-550-044-01 TRANSISTOR 2SB1689-T106
Q617 6-550-044-01 TRANSISTOR 2SB1689-T106
Q618 8-729-907-00 TRANSISTOR DTC114EU
Q621 8-729-021-15 TRANSISTOR 2SD2351T106W
Q622 8-729-021-15 TRANSISTOR 2SD2351T106W
Q623 8-729-028-73 TRANSISTOR DTA114EUA-T106
Q624 8-729-907-00 TRANSISTOR DTC114EU
Q625 8-729-021-15 TRANSISTOR 2SD2351T106W
Q626 8-729-021-15 TRANSISTOR 2SD2351T106W
Q627 8-729-021-15 TRANSISTOR 2SD2351T106W
Q628 8-729-021-15 TRANSISTOR 2SD2351T106W
Q629 8-729-026-53 TRANSISTOR 2SA1576A-T106-QR
Q630 8-729-907-00 TRANSISTOR DTC114EU
MAIN
108
HCD-RV777D/RV888D/RV999D
Ref. No. Part No. Description Remark
Q631 8-729-907-00 TRANSISTOR DTC114EU
Q661 8-729-029-10 TRANSISTOR DTC143TUA-T106
Q662 8-729-905-35 TRANSISTOR 2SC4081-R
Q701 8-729-028-73 TRANSISTOR DTA114EUA-T106
Q702 8-729-028-73 TRANSISTOR DTA114EUA-T106
Q703 8-729-028-73 TRANSISTOR DTA114EUA-T106
Q704 8-729-907-00 TRANSISTOR DTC114EU
Q705 8-729-905-35 TRANSISTOR 2SC4081-R
Q706 8-729-905-35 TRANSISTOR 2SC4081-R
Q707 8-729-028-73 TRANSISTOR DTA114EUA-T106
Q708 8-729-907-00 TRANSISTOR DTC114EU
Q709 8-729-905-35 TRANSISTOR 2SC4081-R
Q710 8-729-905-35 TRANSISTOR 2SC4081-R
Q713 8-729-026-68 TRANSISTOR 2SD2525(TP)
Q714 8-729-907-00 TRANSISTOR DTC114EU
Q719 8-729-028-73 TRANSISTOR DTA114EUA-T106
(RV888D/RV999D)
Q721 8-729-028-73 TRANSISTOR DTA114EUA-T106
Q723 8-729-028-73 TRANSISTOR DTA114EUA-T106
Q724 8-729-028-73 TRANSISTOR DTA114EUA-T106
(RV888D/RV999D)
Q801 8-729-907-00 TRANSISTOR DTC114EU
< RESISTOR >
R101 1-216-821-11 METAL CHIP 1K 5% 1/10W
R102 1-216-821-11 METAL CHIP 1K 5% 1/10W
R111 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V
(RV777D)
R111 1-216-864-11 SHORT CHIP 0 (RV888D/RV999D)
R112 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R113 1-216-833-11 METAL CHIP 10K 5% 1/10W
R114 1-216-833-11 METAL CHIP 10K 5% 1/10W
R115 1-216-821-11 METAL CHIP 1K 5% 1/10W
R116 1-216-841-11 METAL CHIP 47K 5% 1/10W
R117 1-216-841-11 METAL CHIP 47K 5% 1/10W
R118 1-216-833-11 METAL CHIP 10K 5% 1/10W
R119 1-216-809-11 METAL CHIP 100 5% 1/10W
R120 1-216-821-11 METAL CHIP 1K 5% 1/10W
R130 1-216-864-11 SHORT CHIP 0 (RV777D)
R131 1-216-864-11 SHORT CHIP 0
R132 1-216-833-11 METAL CHIP 10K 5% 1/10W
R133 1-216-821-11 METAL CHIP 1K 5% 1/10W
R134 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R140 1-216-821-11 METAL CHIP 1K 5% 1/10W
R141 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R142 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R144 1-216-821-11 METAL CHIP 1K 5% 1/10W
R145 1-216-845-11 METAL CHIP 100K 5% 1/10W
R146 1-216-864-11 SHORT CHIP 0
R147 1-216-821-11 METAL CHIP 1K 5% 1/10W
R148 1-216-845-11 METAL CHIP 100K 5% 1/10W
R149 1-216-821-11 METAL CHIP 1K 5% 1/10W
0R150 1-215-890-11 METAL OXIDE 470 5% 2W F
R151 1-216-833-11 METAL CHIP 10K 5% 1/10W
(RV777D)
R151 1-216-864-11 SHORT CHIP 0 (RV888D/RV999D)
R152 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R153 1-216-833-11 METAL CHIP 10K 5% 1/10W
R154 1-216-833-11 METAL CHIP 10K 5% 1/10W
R155 1-216-821-11 METAL CHIP 1K 5% 1/10W
R156 1-216-841-11 METAL CHIP 47K 5% 1/10W
R157 1-216-841-11 METAL CHIP 47K 5% 1/10W
R158 1-216-833-11 METAL CHIP 10K 5% 1/10W
R159 1-216-809-11 METAL CHIP 100 5% 1/10W
R160 1-216-821-11 METAL CHIP 1K 5% 1/10W
R171 1-216-857-11 METAL CHIP 1M 5% 1/10W
R172 1-216-845-11 METAL CHIP 100K 5% 1/10W
R173 1-216-833-11 METAL CHIP 10K 5% 1/10W
R174 1-216-837-11 METAL CHIP 22K 5% 1/10W
R175 1-216-837-11 METAL CHIP 22K 5% 1/10W
R176 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R177 1-216-845-11 METAL CHIP 100K 5% 1/10W
R178 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R179 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R180 1-216-821-11 METAL CHIP 1K 5% 1/10W
R181 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R182 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R184 1-216-821-11 METAL CHIP 1K 5% 1/10W
R185 1-216-845-11 METAL CHIP 100K 5% 1/10W
R186 1-216-864-11 SHORT CHIP 0
R187 1-216-821-11 METAL CHIP 1K 5% 1/10W
R188 1-216-845-11 METAL CHIP 100K 5% 1/10W
R189 1-216-821-11 METAL CHIP 1K 5% 1/10W
0R190 1-215-890-11 METAL OXIDE 470 5% 2W F
R191 1-216-837-11 METAL CHIP 22K 5% 1/10W
R192 1-216-833-11 METAL CHIP 10K 5% 1/10W
R193 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R194 1-216-821-11 METAL CHIP 1K 5% 1/10W
R195 1-216-845-11 METAL CHIP 100K 5% 1/10W
R196 1-216-837-11 METAL CHIP 22K 5% 1/10W
R197 1-216-841-11 METAL CHIP 47K 5% 1/10W
R230 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R231 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R233 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R271 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
(RV777D)
R271 1-216-864-11 SHORT CHIP 0 (RV888D/RV999D)
R301 1-216-841-11 METAL CHIP 47K 5% 1/10W
(RV888D/RV999D)
R302 1-216-817-11 METAL CHIP 470 5% 1/10W
(RV888D/RV999D)
R303 1-216-833-11 METAL CHIP 10K 5% 1/10W
(RV888D/RV999D)
R304 1-216-833-11 METAL CHIP 10K 5% 1/10W
(RV888D/RV999D)
R305 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
(RV888D/RV999D)
R306 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
(RV888D/RV999D)
R307 1-216-841-11 METAL CHIP 47K 5% 1/10W
(RV888D/RV999D)
R309 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R310 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R311 1-216-841-11 METAL CHIP 47K 5% 1/10W
R312 1-216-857-11 METAL CHIP 1M 5% 1/10W
(RV888D/RV999D)
R313 1-216-833-11 METAL CHIP 10K 5% 1/10W
(RV888D/RV999D)
Ref. No. Part No. Description Remark
MAIN
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
109
HCD-RV777D/RV888D/RV999D
R314 1-216-819-11 METAL CHIP 680 5% 1/10W
(RV888D/RV999D)
R320 1-216-833-11 METAL CHIP 10K 5% 1/10W
(RV888D/RV999D)
R321 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
(RV888D/RV999D)
R322 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
(RV888D/RV999D)
R323 1-216-841-11 METAL CHIP 47K 5% 1/10W
(RV888D/RV999D)
R330 1-216-857-11 METAL CHIP 1M 5% 1/10W
(RV888D/RV999D)
R331 1-216-821-11 METAL CHIP 1K 5% 1/10W
(RV888D/RV999D)
R332 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
(RV888D/RV999D)
R341 1-216-809-11 METAL CHIP 100 5% 1/10W
R342 1-216-809-11 METAL CHIP 100 5% 1/10W
R351 1-216-841-11 METAL CHIP 47K 5% 1/10W
(RV888D/RV999D)
R352 1-216-817-11 METAL CHIP 470 5% 1/10W
(RV888D/RV999D)
R353 1-216-833-11 METAL CHIP 10K 5% 1/10W
(RV888D/RV999D)
R354 1-216-833-11 METAL CHIP 10K 5% 1/10W
(RV888D/RV999D)
R355 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
(RV888D/RV999D)
R356 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
(RV888D/RV999D)
R357 1-216-841-11 METAL CHIP 47K 5% 1/10W
(RV888D/RV999D)
R359 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R360 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R361 1-216-841-11 METAL CHIP 47K 5% 1/10W
R362 1-216-857-11 METAL CHIP 1M 5% 1/10W
(RV888D/RV999D)
R363 1-216-833-11 METAL CHIP 10K 5% 1/10W
(RV888D/RV999D)
R364 1-216-819-11 METAL CHIP 680 5% 1/10W
(RV888D/RV999D)
R371 1-216-864-11 SHORT CHIP 0 (RV888D/RV999D)
R372 1-216-864-11 SHORT CHIP 0 (RV888D/RV999D)
R373 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
(RV888D/RV999D)
R374 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
(RV888D/RV999D)
R375 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
(RV888D/RV999D)
R376 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R377 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
(RV777D)
R377 1-216-864-11 SHORT CHIP 0 (RV888D/RV999D)
R381 1-216-833-11 METAL CHIP 10K 5% 1/10W
(RV777D)
R381 1-216-845-11 METAL CHIP 100K 5% 1/10W
(RV888D/RV999D)
R382 1-216-833-11 METAL CHIP 10K 5% 1/10W
(RV777D)
R382 1-216-845-11 METAL CHIP 100K 5% 1/10W
(RV888D/RV999D)
R383 1-216-845-11 METAL CHIP 100K 5% 1/10W
(RV888D/RV999D)
R384 1-216-845-11 METAL CHIP 100K 5% 1/10W
(RV888D/RV999D)
R385 1-216-845-11 METAL CHIP 100K 5% 1/10W
(RV888D/RV999D)
R386 1-216-845-11 METAL CHIP 100K 5% 1/10W
R387 1-216-845-11 METAL CHIP 100K 5% 1/10W
(RV888D/RV999D)
R388 1-216-845-11 METAL CHIP 100K 5% 1/10W
(RV888D/RV999D)
R393 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
(RV888D/RV999D)
R394 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
(RV888D/RV999D)
R395 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
(RV888D/RV999D)
R397 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R563 1-216-833-11 METAL CHIP 10K 5% 1/10W
R601 1-216-838-11 METAL CHIP 27K 5% 1/10W
R602 1-216-809-11 METAL CHIP 100 5% 1/10W
R603 1-216-833-11 METAL CHIP 10K 5% 1/10W
R604 1-216-833-11 METAL CHIP 10K 5% 1/10W
R605 1-216-833-11 METAL CHIP 10K 5% 1/10W
R607 1-216-833-11 METAL CHIP 10K 5% 1/10W
R608 1-216-845-11 METAL CHIP 100K 5% 1/10W
R609 1-216-833-11 METAL CHIP 10K 5% 1/10W
R610 1-216-845-11 METAL CHIP 100K 5% 1/10W
R611 1-216-821-11 METAL CHIP 1K 5% 1/10W
R612 1-216-821-11 METAL CHIP 1K 5% 1/10W
R613 1-216-851-11 METAL CHIP 330K 5% 1/10W
R614 1-216-834-11 METAL CHIP 12K 5% 1/10W
R615 1-216-812-11 METAL CHIP 180 5% 1/10W
R616 1-216-834-11 METAL CHIP 12K 5% 1/10W
R617 1-216-835-11 METAL CHIP 15K 5% 1/10W
R618 1-216-823-11 METAL CHIP 1.5K 5% 1/10W
R620 1-216-857-11 METAL CHIP 1M 5% 1/10W
R621 1-216-821-11 METAL CHIP 1K 5% 1/10W
R622 1-216-821-11 METAL CHIP 1K 5% 1/10W
R623 1-216-821-11 METAL CHIP 1K 5% 1/10W
R624 1-216-821-11 METAL CHIP 1K 5% 1/10W
R625 1-216-821-11 METAL CHIP 1K 5% 1/10W
R626 1-216-821-11 METAL CHIP 1K 5% 1/10W
R627 1-216-833-11 METAL CHIP 10K 5% 1/10W
R628 1-216-833-11 METAL CHIP 10K 5% 1/10W
R629 1-216-833-11 METAL CHIP 10K 5% 1/10W
R639 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R651 1-216-821-11 METAL CHIP 1K 5% 1/10W
R652 1-216-821-11 METAL CHIP 1K 5% 1/10W
R653 1-216-851-11 METAL CHIP 330K 5% 1/10W
R654 1-216-834-11 METAL CHIP 12K 5% 1/10W
R655 1-216-812-11 METAL CHIP 180 5% 1/10W
R656 1-216-834-11 METAL CHIP 12K 5% 1/10W
R657 1-216-835-11 METAL CHIP 15K 5% 1/10W
R658 1-216-823-11 METAL CHIP 1.5K 5% 1/10W
R661 1-216-851-11 METAL CHIP 330K 5% 1/10W
R662 1-216-835-11 METAL CHIP 15K 5% 1/10W
R663 1-216-835-11 METAL CHIP 15K 5% 1/10W
R664 1-216-833-11 METAL CHIP 10K 5% 1/10W
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
MAIN
110
HCD-RV777D/RV888D/RV999D
R665 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R666 1-216-837-11 METAL CHIP 22K 5% 1/10W
R667 1-216-837-11 METAL CHIP 22K 5% 1/10W
R668 1-216-838-11 METAL CHIP 27K 5% 1/10W
R669 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R675 1-216-833-11 METAL CHIP 10K 5% 1/10W
R676 1-216-841-11 METAL CHIP 47K 5% 1/10W
R677 1-216-833-11 METAL CHIP 10K 5% 1/10W
R678 1-216-833-11 METAL CHIP 10K 5% 1/10W
R679 1-216-833-11 METAL CHIP 10K 5% 1/10W
R680 1-216-833-11 METAL CHIP 10K 5% 1/10W
R681 1-216-833-11 METAL CHIP 10K 5% 1/10W
R682 1-216-833-11 METAL CHIP 10K 5% 1/10W
R683 1-216-821-11 METAL CHIP 1K 5% 1/10W
R684 1-216-819-11 METAL CHIP 680 5% 1/10W
R685 1-216-821-11 METAL CHIP 1K 5% 1/10W
R686 1-216-819-11 METAL CHIP 680 5% 1/10W
R687 1-216-821-11 METAL CHIP 1K 5% 1/10W
R688 1-216-819-11 METAL CHIP 680 5% 1/10W
R693 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R694 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R706 1-216-821-11 METAL CHIP 1K 5% 1/10W
R707 1-216-841-11 METAL CHIP 47K 5% 1/10W
R708 1-216-833-11 METAL CHIP 10K 5% 1/10W
R709 1-216-841-11 METAL CHIP 47K 5% 1/10W
R710 1-216-821-11 METAL CHIP 1K 5% 1/10W
R711 1-216-833-11 METAL CHIP 10K 5% 1/10W
R726 1-216-833-11 METAL CHIP 10K 5% 1/10W
R727 1-216-821-11 METAL CHIP 1K 5% 1/10W
R729 1-216-821-11 METAL CHIP 1K 5% 1/10W
R730 1-216-833-11 METAL CHIP 10K 5% 1/10W
R736 1-216-841-11 METAL CHIP 47K 5% 1/10W
R743 1-216-841-11 METAL CHIP 47K 5% 1/10W
R744 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R745 1-216-817-11 METAL CHIP 470 5% 1/10W
R746 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R747 1-216-841-11 METAL CHIP 47K 5% 1/10W
R748 1-216-849-11 METAL CHIP 220K 5% 1/10W
R749 1-216-837-11 METAL CHIP 22K 5% 1/10W
R750 1-216-837-11 METAL CHIP 22K 5% 1/10W
R753 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W
R754 1-216-837-11 METAL CHIP 22K 5% 1/10W
R755 1-216-837-11 METAL CHIP 22K 5% 1/10W
R760 1-216-821-11 METAL CHIP 1K 5% 1/10W
(RV888D/RV999D)
R761 1-216-841-11 METAL CHIP 47K 5% 1/10W
(RV888D/RV999D)
R762 1-216-833-11 METAL CHIP 10K 5% 1/10W
(RV888D/RV999D)
R764 1-216-841-11 METAL CHIP 47K 5% 1/10W
R766 1-216-821-11 METAL CHIP 1K 5% 1/10W
R767 1-216-841-11 METAL CHIP 47K 5% 1/10W
R768 1-216-833-11 METAL CHIP 10K 5% 1/10W
R774 1-216-864-11 SHORT CHIP 0
R776 1-216-833-11 METAL CHIP 10K 5% 1/10W
R777 1-216-833-11 METAL CHIP 10K 5% 1/10W
(RV888D/RV999D)
R778 1-216-841-11 METAL CHIP 47K 5% 1/10W
(RV888D/RV999D)
R779 1-216-821-11 METAL CHIP 1K 5% 1/10W
(RV888D/RV999D)
R780 1-216-833-11 METAL CHIP 10K 5% 1/10W
R801 1-216-809-11 METAL CHIP 100 5% 1/10W
R802 1-216-809-11 METAL CHIP 100 5% 1/10W
R803 1-216-809-11 METAL CHIP 100 5% 1/10W
R804 1-216-809-11 METAL CHIP 100 5% 1/10W
R805 1-216-809-11 METAL CHIP 100 5% 1/10W
R806 1-216-809-11 METAL CHIP 100 5% 1/10W
R807 1-216-809-11 METAL CHIP 100 5% 1/10W
R808 1-216-864-11 SHORT CHIP 0
R809 1-216-809-11 METAL CHIP 100 5% 1/10W
R811 1-216-851-11 METAL CHIP 330K 5% 1/10W
R812 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R813 1-216-845-11 METAL CHIP 100K 5% 1/10W
R817 1-216-809-11 METAL CHIP 100 5% 1/10W
R818 1-216-833-11 METAL CHIP 10K 5% 1/10W
R819 1-216-809-11 METAL CHIP 100 5% 1/10W
R820 1-216-833-11 METAL CHIP 10K 5% 1/10W
R821 1-216-809-11 METAL CHIP 100 5% 1/10W
R822 1-216-809-11 METAL CHIP 100 5% 1/10W
R823 1-216-809-11 METAL CHIP 100 5% 1/10W
R824 1-216-809-11 METAL CHIP 100 5% 1/10W
R825 1-216-809-11 METAL CHIP 100 5% 1/10W
R826 1-216-833-11 METAL CHIP 10K 5% 1/10W
R829 1-216-809-11 METAL CHIP 100 5% 1/10W
R830 1-216-809-11 METAL CHIP 100 5% 1/10W
R831 1-216-809-11 METAL CHIP 100 5% 1/10W
R832 1-216-809-11 METAL CHIP 100 5% 1/10W
R833 1-216-809-11 METAL CHIP 100 5% 1/10W
R834 1-216-809-11 METAL CHIP 100 5% 1/10W
R835 1-216-809-11 METAL CHIP 100 5% 1/10W
R836 1-216-809-11 METAL CHIP 100 5% 1/10W
R847 1-216-809-11 METAL CHIP 100 5% 1/10W
R848 1-216-809-11 METAL CHIP 100 5% 1/10W
R849 1-216-809-11 METAL CHIP 100 5% 1/10W
R850 1-216-809-11 METAL CHIP 100 5% 1/10W
R851 1-216-809-11 METAL CHIP 100 5% 1/10W
R852 1-216-809-11 METAL CHIP 100 5% 1/10W
R853 1-216-809-11 METAL CHIP 100 5% 1/10W
R854 1-216-809-11 METAL CHIP 100 5% 1/10W
R855 1-216-809-11 METAL CHIP 100 5% 1/10W
R856 1-216-821-11 METAL CHIP 1K 5% 1/10W
R857 1-216-821-11 METAL CHIP 1K 5% 1/10W
R858 1-216-833-11 METAL CHIP 10K 5% 1/10W
R859 1-216-833-11 METAL CHIP 10K 5% 1/10W
R860 1-216-833-11 METAL CHIP 10K 5% 1/10W
R861 1-216-833-11 METAL CHIP 10K 5% 1/10W
R862 1-216-833-11 METAL CHIP 10K 5% 1/10W
R863 1-216-833-11 METAL CHIP 10K 5% 1/10W
R867 1-216-809-11 METAL CHIP 100 5% 1/10W
R868 1-216-809-11 METAL CHIP 100 5% 1/10W
R869 1-216-809-11 METAL CHIP 100 5% 1/10W
R870 1-216-809-11 METAL CHIP 100 5% 1/10W
R871 1-216-809-11 METAL CHIP 100 5% 1/10W
R872 1-216-809-11 METAL CHIP 100 5% 1/10W
R873 1-216-809-11 METAL CHIP 100 5% 1/10W
R874 1-216-809-11 METAL CHIP 100 5% 1/10W
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
MAIN
111
HCD-RV777D/RV888D/RV999D
R875 1-216-809-11 METAL CHIP 100 5% 1/10W
R885 1-216-809-11 METAL CHIP 100 5% 1/10W
R886 1-216-809-11 METAL CHIP 100 5% 1/10W
R887 1-216-821-11 METAL CHIP 1K 5% 1/10W
R888 1-216-809-11 METAL CHIP 100 5% 1/10W
R893 1-216-819-11 METAL CHIP 680 5% 1/10W
(RV777D)
R893 1-216-821-11 METAL CHIP 1K 5% 1/10W
(RV888D)
R893 1-216-823-11 METAL CHIP 1.5K 5% 1/10W
(RV999D)
R894 1-216-815-11 METAL CHIP 330 5% 1/10W
(E3,E15)
R894 1-216-821-11 METAL CHIP 1K 5% 1/10W
(EA)
R894 1-216-823-11 METAL CHIP 1.5K 5% 1/10W
(AUS)
R894 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
(E51,AR,MX)
R894 1-216-864-11 SHORT CHIP 0 (PH,SP,MY)
R895 1-216-809-11 METAL CHIP 100 5% 1/10W
R896 1-216-809-11 METAL CHIP 100 5% 1/10W
R897 1-216-809-11 METAL CHIP 100 5% 1/10W
R899 1-216-809-11 METAL CHIP 100 5% 1/10W
R900 1-216-809-11 METAL CHIP 100 5% 1/10W
R901 1-216-833-11 METAL CHIP 10K 5% 1/10W
R902 1-216-809-11 METAL CHIP 100 5% 1/10W
R929 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R930 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R947 1-216-833-11 METAL CHIP 10K 5% 1/10W
R948 1-216-833-11 METAL CHIP 10K 5% 1/10W
R972 1-216-833-11 METAL CHIP 10K 5% 1/10W
R973 1-216-833-11 METAL CHIP 10K 5% 1/10W
R974 1-216-833-11 METAL CHIP 10K 5% 1/10W
R975 1-216-833-11 METAL CHIP 10K 5% 1/10W
R993 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R994 1-216-821-11 METAL CHIP 1K 5% 1/10W
(E51,AR,MX)
R994 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
(E3,E15,AUS,EA)
< TRANSFORMER >
T601 1-437-220-11 TRANSFORMER, BIAS OSCILLATION
< VIBRATOR >
X800 1-760-252-12 VIBRATOR, CRYSTAL (32.768kHz)
X801 1-781-107-21 VIBRATOR, CERAMIC (16MHz)
*************************************************************
1-687-133-12 MOTOR (LD) BOARD
*****************
*************************************************************
1-687-134-12 MOTOR (TB) BOARD
*****************
< CONNECTOR >
CN742 1-784-727-11 CONNECTOR, FFC 5P
*************************************************************
Ref. No. Part No. Description Remark
A-4751-844-A PANEL BOARD, COMPLETE
**********************
< CAPACITOR >
C101 1-126-382-11 ELECT 100uF 20% 16V
C102 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C106 1-162-995-11 CERAMIC CHIP 0.022uF 50V
C107 1-162-953-11 CERAMIC CHIP 100PF 5% 50V
C108 1-162-953-11 CERAMIC CHIP 100PF 5% 50V
C109 1-162-953-11 CERAMIC CHIP 100PF 5% 50V
C121 1-126-794-11 ELECT 4.7uF 20% 50V
C122 1-126-794-11 ELECT 4.7uF 20% 50V
C125 1-126-382-11 ELECT 100uF 20% 16V
C126 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C160 1-119-943-11 ELECT 47uF 20% 50V
C161 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C206 1-126-382-11 ELECT 100uF 20% 16V
C207 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C208 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C333 1-162-953-11 CERAMIC CHIP 100PF 5% 50V
C334 1-162-953-11 CERAMIC CHIP 100PF 5% 50V
C335 1-162-953-11 CERAMIC CHIP 100PF 5% 50V
C336 1-162-953-11 CERAMIC CHIP 100PF 5% 50V
C337 1-162-953-11 CERAMIC CHIP 100PF 5% 50V
C338 1-162-953-11 CERAMIC CHIP 100PF 5% 50V
C339 1-162-953-11 CERAMIC CHIP 100PF 5% 50V
C340 1-162-953-11 CERAMIC CHIP 100PF 5% 50V
C341 1-162-953-11 CERAMIC CHIP 100PF 5% 50V
C342 1-162-953-11 CERAMIC CHIP 100PF 5% 50V
C343 1-162-953-11 CERAMIC CHIP 100PF 5% 50V
C344 1-162-953-11 CERAMIC CHIP 100PF 5% 50V
C345 1-162-953-11 CERAMIC CHIP 100PF 5% 50V
< CONNECTOR >
CN2 1-785-331-11 PIN, CONNECTOR (LIGHT ANGLE) 5P
CN101 1-784-737-11 CONNECTOR, FFC 15P
CN103 1-818-282-11 PIN, CONNECTOR 3P
CN104 1-785-332-11 PIN, CONNECTOR (LIGHT ANGLE) 6P
< DIODE >
D192 6-500-809-01 LED SELU5223C-STP15 (?/1)
< FERRITE BEAD >
FB101 1-469-869-21 INDUCTOR (EMI FERRITE) (2012)
FB102 1-469-869-21 INDUCTOR (EMI FERRITE) (2012)
< FLUORESCENT INDICATOR >
FL1001 1-518-989-11 INDICATOR TUBE, FLUORESCENT
< IC >
IC101 6-804-223-01 IC uPD780232GC-504-8BT-A
< TRANSISTOR >
Q134 8-729-907-00 TRANSISTOR DTC114EU
Q135 8-729-907-00 TRANSISTOR DTC114EU
Q136 8-729-907-00 TRANSISTOR DTC114EU
Q137 8-729-907-00 TRANSISTOR DTC114EU
Ref. No. Part No. Description Remark
MAIN PANELMOTOR (TB)MOTOR (LD)
112
HCD-RV777D/RV888D/RV999D
Q138 8-729-907-00 TRANSISTOR DTC114EU
Q139 8-729-907-00 TRANSISTOR DTC114EU
< RESISTOR >
R11 1-216-817-11 METAL CHIP 470 5% 1/10W
R12 1-216-819-11 METAL CHIP 680 5% 1/10W
R13 1-216-821-11 METAL CHIP 1K 5% 1/10W
R14 1-216-823-11 METAL CHIP 1.5K 5% 1/10W
R15 1-216-823-11 METAL CHIP 1.5K 5% 1/10W
R16 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R17 1-216-827-11 METAL CHIP 3.3K 5% 1/10W
R18 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R19 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W
R20 1-216-833-11 METAL CHIP 10K 5% 1/10W
R31 1-216-817-11 METAL CHIP 470 5% 1/10W
R32 1-216-819-11 METAL CHIP 680 5% 1/10W
R33 1-216-821-11 METAL CHIP 1K 5% 1/10W
R34 1-216-823-11 METAL CHIP 1.5K 5% 1/10W
R35 1-216-823-11 METAL CHIP 1.5K 5% 1/10W
R36 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R37 1-216-827-11 METAL CHIP 3.3K 5% 1/10W
R38 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R39 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W
R40 1-216-833-11 METAL CHIP 10K 5% 1/10W
R51 1-216-817-11 METAL CHIP 470 5% 1/10W
R52 1-216-819-11 METAL CHIP 680 5% 1/10W
R53 1-216-821-11 METAL CHIP 1K 5% 1/10W
R54 1-216-823-11 METAL CHIP 1.5K 5% 1/10W
R55 1-216-823-11 METAL CHIP 1.5K 5% 1/10W
R56 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R57 1-216-827-11 METAL CHIP 3.3K 5% 1/10W
R58 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R59 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W
R60 1-216-833-11 METAL CHIP 10K 5% 1/10W
R61 1-216-835-11 METAL CHIP 15K 5% 1/10W
R105 1-216-821-11 METAL CHIP 1K 5% 1/10W
R106 1-216-821-11 METAL CHIP 1K 5% 1/10W
R107 1-216-809-11 METAL CHIP 100 5% 1/10W
R108 1-216-809-11 METAL CHIP 100 5% 1/10W
R109 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R115 1-216-821-11 METAL CHIP 1K 5% 1/10W
R116 1-216-821-11 METAL CHIP 1K 5% 1/10W
R117 1-216-833-11 METAL CHIP 10K 5% 1/10W
R118 1-216-833-11 METAL CHIP 10K 5% 1/10W
R123 1-216-835-11 METAL CHIP 15K 5% 1/10W
R124 1-216-835-11 METAL CHIP 15K 5% 1/10W
R125 1-216-835-11 METAL CHIP 15K 5% 1/10W
R127 1-216-813-11 METAL CHIP 220 5% 1/10W
R128 1-216-813-11 METAL CHIP 220 5% 1/10W
R129 1-216-813-11 METAL CHIP 220 5% 1/10W
R130 1-216-813-11 METAL CHIP 220 5% 1/10W
R131 1-216-813-11 METAL CHIP 220 5% 1/10W
R132 1-216-813-11 METAL CHIP 220 5% 1/10W
R133 1-216-813-11 METAL CHIP 220 5% 1/10W
R134 1-216-813-11 METAL CHIP 220 5% 1/10W
R135 1-216-813-11 METAL CHIP 220 5% 1/10W
R136 1-216-813-11 METAL CHIP 220 5% 1/10W
R137 1-216-813-11 METAL CHIP 220 5% 1/10W
R138 1-216-813-11 METAL CHIP 220 5% 1/10W
R140 1-216-841-11 METAL CHIP 47K 5% 1/10W
R141 1-216-841-11 METAL CHIP 47K 5% 1/10W
R142 1-216-841-11 METAL CHIP 47K 5% 1/10W
R143 1-216-841-11 METAL CHIP 47K 5% 1/10W
R144 1-216-841-11 METAL CHIP 47K 5% 1/10W
R145 1-216-841-11 METAL CHIP 47K 5% 1/10W
R146 1-216-841-11 METAL CHIP 47K 5% 1/10W
R147 1-216-841-11 METAL CHIP 47K 5% 1/10W
R148 1-216-841-11 METAL CHIP 47K 5% 1/10W
R149 1-216-841-11 METAL CHIP 47K 5% 1/10W
R150 1-216-841-11 METAL CHIP 47K 5% 1/10W
R151 1-216-841-11 METAL CHIP 47K 5% 1/10W
R152 1-216-841-11 METAL CHIP 47K 5% 1/10W
R153 1-216-841-11 METAL CHIP 47K 5% 1/10W
R154 1-216-841-11 METAL CHIP 47K 5% 1/10W
R155 1-216-841-11 METAL CHIP 47K 5% 1/10W
R156 1-216-841-11 METAL CHIP 47K 5% 1/10W
R157 1-216-841-11 METAL CHIP 47K 5% 1/10W
R158 1-216-841-11 METAL CHIP 47K 5% 1/10W
R159 1-216-841-11 METAL CHIP 47K 5% 1/10W
R160 1-216-841-11 METAL CHIP 47K 5% 1/10W
R161 1-216-841-11 METAL CHIP 47K 5% 1/10W
R162 1-216-841-11 METAL CHIP 47K 5% 1/10W
R163 1-216-841-11 METAL CHIP 47K 5% 1/10W
R164 1-216-841-11 METAL CHIP 47K 5% 1/10W
R165 1-216-841-11 METAL CHIP 47K 5% 1/10W
R166 1-216-841-11 METAL CHIP 47K 5% 1/10W
R167 1-216-841-11 METAL CHIP 47K 5% 1/10W
R168 1-216-841-11 METAL CHIP 47K 5% 1/10W
R169 1-216-841-11 METAL CHIP 47K 5% 1/10W
R170 1-216-841-11 METAL CHIP 47K 5% 1/10W
R171 1-216-841-11 METAL CHIP 47K 5% 1/10W
R172 1-216-841-11 METAL CHIP 47K 5% 1/10W
R173 1-216-841-11 METAL CHIP 47K 5% 1/10W
R205 1-216-828-11 METAL CHIP 3.9K 5% 1/10W
R206 1-216-851-11 METAL CHIP 330K 5% 1/10W
< SWITCH >
S11 1-762-875-21 SWITCH, KEYBOARD (?/1)
S12 1-762-875-21 SWITCH, KEYBOARD (DISPLAY)
S13 1-762-875-21 SWITCH, KEYBOARD (EQ BAND)
S14 1-762-875-21 SWITCH, KEYBOARD (DISC 1)
S15 1-762-875-21 SWITCH, KEYBOARD (DISC 2)
S16 1-762-875-21 SWITCH, KEYBOARD (DISC 3)
S17 1-762-875-21 SWITCH, KEYBOARD (DISC SKIP/EX-CHANGE)
S18 1-762-875-21 SWITCH, KEYBOARD (Z)
S19 1-762-875-21 SWITCH, KEYBOARD (KARAOKE/MPX)
S20 1-762-875-21 SWITCH, KEYBOARD (P FILE)
S21 1-762-875-21 SWITCH, KEYBOARD (PRESET EQ)
S22 1-762-875-21 SWITCH, KEYBOARD (ENTER)
S31 1-762-875-21 SWITCH, KEYBOARD (DVD)
S32 1-762-875-21 SWITCH, KEYBOARD (TUNER/BAND)
S33 1-762-875-21 SWITCH, KEYBOARD (TAPE A/B)
S34 1-762-875-21 SWITCH, KEYBOARD (GAME)
S35 1-762-875-21 SWITCH, KEYBOARD (VIDEO/SAT)
S36 1-762-875-21 SWITCH, KEYBOARD (ILLUMINATION)
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
PANEL
113
HCD-RV777D/RV888D/RV999D
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
S37 1-762-875-21 SWITCH, KEYBOARD
(PLAY MODE/TUNING MODE)
S38 1-762-875-21 SWITCH, KEYBOARD (GAME MIXING)
S39 1-762-875-21 SWITCH, KEYBOARD (CD SYNC)
S40 1-762-875-21 SWITCH, KEYBOARD (REC PAUSE/START)
S51 1-762-875-21 SWITCH, KEYBOARD (GROOVE)
S52 1-762-875-21 SWITCH, KEYBOARD (SOUND FIELD)
S53 1-762-875-21 SWITCH, KEYBOARD (EFFECT ON/OFF)
S54 1-762-875-21 SWITCH, KEYBOARD (TUNING +)
S55 1-762-875-21 SWITCH, KEYBOARD (G/g)
S56 1-762-875-21 SWITCH, KEYBOARD (M ALBUM +)
S57 1-762-875-21 SWITCH, KEYBOARD (m ALBUM –)
S58 1-762-875-21 SWITCH, KEYBOARD (X)
S59 1-762-875-21 SWITCH, KEYBOARD (x)
S60 1-762-875-21 SWITCH, KEYBOARD (TUNING –)
< VIBRATOR >
X101 1-795-058-21 VIBRATOR, CERAMIC (5MHz)
*************************************************************
P-STREAM BOARD
****************
< DIODE >
D134 6-500-809-01 LED SELU5223C-STP15 (ILLUMINATION)
D135 6-500-809-01 LED SELU5223C-STP15 (ILLUMINATION)
D136 6-500-809-01 LED SELU5223C-STP15 (ILLUMINATION)
D137 6-500-809-01 LED SELU5223C-STP15 (ILLUMINATION)
D138 6-500-809-01 LED SELU5223C-STP15 (ILLUMINATION)
D139 6-500-809-01 LED SELU5223C-STP15 (ILLUMINATION)
< RESISTOR >
R62 1-216-837-11 METAL CHIP 22K 5% 1/10W
R119 1-216-864-11 SHORT CHIP 0
R120 1-216-864-11 SHORT CHIP 0
< SWITCH >
S102 1-418-632-11 ENCODER, ROTARY (MASTER VOLUME)
S701 1-786-289-11 SWITCH, DETECTION (l – EQ + L)
*************************************************************
A-4728-690-A RF BOARD, COMPLETE
*******************
< CAPACITOR >
C001 1-126-206-11 ELECT CHIP 100uF 20% 6.3V
C002 1-124-779-00 ELECT CHIP 10uF 20% 16V
C003 1-126-206-11 ELECT CHIP 100uF 20% 6.3V
C004 1-124-779-00 ELECT CHIP 10uF 20% 16V
C005 1-128-993-21 ELECT CHIP 22uF 20% 10V
C006 1-128-993-21 ELECT CHIP 22uF 20% 10V
C008 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C009 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C010 1-115-416-11 CERAMIC CHIP 0.001uF 5% 25V
C011 1-115-416-11 CERAMIC CHIP 0.001uF 5% 25V
C012 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C013 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C014 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C015 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C016 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C017 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C018 1-164-172-11 CERAMIC CHIP 0.0056uF 10% 25V
C019 1-164-172-11 CERAMIC CHIP 0.0056uF 10% 25V
C020 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C021 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C022 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C023 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C024 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C025 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C026 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C027 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C028 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C029 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C030 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C031 1-115-416-11 CERAMIC CHIP 0.001uF 5% 25V
C032 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V
C033 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C034 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C035 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C036 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10V
C037 1-115-412-11 CERAMIC CHIP 680PF 5% 25V
C038 1-164-677-11 CERAMIC CHIP 0.033uF 10% 16V
C039 1-164-677-11 CERAMIC CHIP 0.033uF 10% 16V
C040 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C041 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C042 1-164-218-11 CERAMIC CHIP 180PF 5% 50V
C049 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C050 1-162-967-11 CERAMIC CHIP 0.0033uF 10% 50V
C051 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10V
C052 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
< CONNECTOR >
CN001 1-815-031-11 CONNECTOR, FFC/FPC (ZIF) 24P
CN002 1-784-836-21 CONNECTOR, FFC (LIF(NON-ZIF)) 29P
CN003 1-784-861-21 CONNECTOR, FFC (LIF(NON-ZIF)) 9P
< DIODE >
D001 8-719-988-61 DIODE 1SS355TE-17
D002 8-719-988-61 DIODE 1SS355TE-17
< IC >
IC001 6-703-922-01 IC SP3723CAF0PM
IC003 6-703-921-01 IC TL343IDBVR
< COIL >
L001 1-412-031-11 INDUCTOR 47uH
L002 1-412-031-11 INDUCTOR 47uH
< TRANSISTOR >
Q001 8-729-903-46 TRANSISTOR 2SB1132-P
Q002 8-729-903-46 TRANSISTOR 2SB1132-P
< RESISTOR >
R001 1-218-668-11 METAL CHIP 100 0.5% 1/10W
R003 1-216-803-11 METAL CHIP 33 5% 1/10W
R004 1-216-803-11 METAL CHIP 33 5% 1/10W
PANEL RFP-STREAM
114
HCD-RV777D/RV888D/RV999D
SENSOR
RF SURROUND AMP
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R005 1-216-841-11 METAL CHIP 47K 5% 1/10W
R006 1-216-817-11 METAL CHIP 470 5% 1/10W
R007 1-216-803-11 METAL CHIP 33 5% 1/10W
R008 1-216-803-11 METAL CHIP 33 5% 1/10W
R009 1-216-841-11 METAL CHIP 47K 5% 1/10W
R010 1-216-817-11 METAL CHIP 470 5% 1/10W
R011 1-216-864-11 SHORT CHIP 0
R012 1-216-864-11 SHORT CHIP 0
R013 1-216-864-11 SHORT CHIP 0
R014 1-216-864-11 SHORT CHIP 0
R015 1-216-864-11 SHORT CHIP 0
R016 1-216-864-11 SHORT CHIP 0
R017 1-216-864-11 SHORT CHIP 0
R018 1-216-864-11 SHORT CHIP 0
R019 1-216-864-11 SHORT CHIP 0
R020 1-216-864-11 SHORT CHIP 0
R021 1-216-864-11 SHORT CHIP 0
R022 1-216-813-11 METAL CHIP 220 5% 1/10W
R023 1-216-820-11 METAL CHIP 820 5% 1/10W
R024 1-216-864-11 SHORT CHIP 0
R025 1-216-809-11 METAL CHIP 100 5% 1/10W
R026 1-218-718-11 METAL CHIP 12K 0.5% 1/10W
R027 1-216-864-11 SHORT CHIP 0
R028 1-216-864-11 SHORT CHIP 0
R029 1-216-864-11 SHORT CHIP 0
R031 1-216-809-11 METAL CHIP 100 5% 1/10W
R033 1-216-845-11 METAL CHIP 100K 5% 1/10W
R034 1-216-817-11 METAL CHIP 470 5% 1/10W
R035 1-216-864-11 SHORT CHIP 0
R041 1-216-821-11 METAL CHIP 1K 5% 1/10W
R046 1-216-833-11 METAL CHIP 10K 5% 1/10W
R047 1-216-839-11 METAL CHIP 33K 5% 1/10W
R091 1-218-913-11 METAL CHIP 560K 0.5% 1/10W
*************************************************************
1-687-132-12 SENSOR BOARD
**************
< CONNECTOR >
CN731 1-785-329-21 PIN, CONNECTOR (LIGHT ANGLE) 3P
< IC >
IC731 6-600-022-01 IC RPI-576
*************************************************************
SIRCS BOARD
************
< CAPACITOR >
C205 1-162-974-11 CERAMIC CHIP 0.01uF 50V
< CONNECTOR >
CN113 1-816-423-11 SOCKET, CONNECTOR 3P
< IC >
IC202 6-600-174-01 IC RPM7240-H4 (IR)
*************************************************************
SUB TRANS BOARD
*****************
1-533-217-41 HOLDER, FUSE
< CAPACITOR >
0C901 1-113-925-11 CERAMIC 0.01uF 20% 250V
C902 1-126-768-11 ELECT 2200uF 20% 16V
C903 1-126-933-11 ELECT 100uF 20% 16V
< CONNECTOR >
CN901 1-564-321-00 PIN, CONNECTOR (3.96mm PITCH) 2P
*CN902 1-564-321-21 PIN, CONNECTOR (3.96mm PITCH) 2P
(AUS,AR,MX)
CN902 1-568-106-11 PIN, CONNECTOR (3.96mm PITCH) 4P
(EXCEPT AUS,AR,MX)
CN903 1-506-468-11 PIN, CONNECTOR 3P
< DIODE >
D901 8-719-991-33 DIODE 1SS133T-77
0D902 6-500-522-11 DIODE 10EDB40-TA2B5
0D903 6-500-522-11 DIODE 10EDB40-TA2B5
0D904 6-500-522-11 DIODE 10EDB40-TA2B5
0D905 6-500-522-11 DIODE 10EDB40-TA2B5
< IC >
IC901 6-701-760-01 IC uPC3504AHF
< TRANSISTOR >
Q901 8-729-119-78 TRANSISTOR 2SC2785-HFE
< RESISTOR >
R901 1-249-429-11 CARBON 10K 5% 1/4W
R904 1-247-791-11 CARBON 22 5% 1/4W
< RELAY >
0RY901 1-755-467-11 RELAY (POWER)
< SWITCH >
0S901 1-786-055-21 SELECTOR, VOLTAGE (VOLTAGE SELECTOR)
(EXCEPT AUS,AR,MX)
< TRANSFORMER >
0T901 1-437-677-11 TRANSFORMER, POWER
*************************************************************
A-1053-983-A SURROUND AMP BOARD, COMPLETE (RV888D)
A-4751-859-A SURROUND AMP BOARD, COMPLETE (RV999D)
******************************
7-685-872-09 SCREW +BVTT 3X8 (S) (RV888D/RV999D)
< CAPACITOR >
C301 1-126-964-11 ELECT 10uF 20% 50V
(RV888D/RV999D)
C302 1-162-294-31 CERAMIC 0.001uF 10% 50V
(RV888D/RV999D)
C303 1-162-286-31 CERAMIC 220PF 10% 50V
(RV888D/RV999D)
SUB TRANSSIRCS
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
115
HCD-RV777D/RV888D/RV999D
C304 1-126-964-11 ELECT 10uF 20% 50V
(RV888D/RV999D)
C306 1-136-497-81 FILM 0.1uF 5% 50V
(RV888D/RV999D)
C307 1-136-497-81 FILM 0.1uF 5% 50V
(RV888D/RV999D)
C308 1-126-968-11 ELECT 100uF 20% 50V
(RV888D/RV999D)
C310 1-162-199-31 CERAMIC 10PF 5% 50V
(RV888D/RV999D)
C311 1-162-199-31 CERAMIC 10PF 5% 50V
(RV888D/RV999D)
C312 1-162-199-31 CERAMIC 10PF 5% 50V
(RV888D/RV999D)
C341 1-126-964-11 ELECT 10uF 20% 50V
(RV888D/RV999D)
C342 1-162-294-31 CERAMIC 0.001uF 10% 50V
(RV888D/RV999D)
C343 1-162-286-31 CERAMIC 220PF 10% 50V
(RV888D/RV999D)
C344 1-126-964-11 ELECT 10uF 20% 50V
(RV888D/RV999D)
C346 1-136-497-81 FILM 0.1uF 5% 50V
(RV888D/RV999D)
C347 1-136-497-81 FILM 0.1uF 5% 50V
(RV888D/RV999D)
C351 1-126-964-11 ELECT 10uF 20% 50V
(RV888D/RV999D)
C352 1-162-294-31 CERAMIC 0.001uF 10% 50V
(RV888D/RV999D)
C353 1-162-286-31 CERAMIC 220PF 10% 50V
(RV888D/RV999D)
C354 1-126-964-11 ELECT 10uF 20% 50V
(RV888D/RV999D)
C356 1-136-497-81 FILM 0.1uF 5% 50V
(RV888D/RV999D)
C357 1-136-497-81 FILM 0.1uF 5% 50V
(RV888D/RV999D)
C371 1-136-153-00 FILM 0.01uF 5% 50V
(RV888D/RV999D)
C372 1-136-153-00 FILM 0.01uF 5% 50V
(RV888D/RV999D)
C373 1-137-844-21 ELECT 2200uF 20% 42V
(RV888D/RV999D)
C374 1-137-844-21 ELECT 2200uF 20% 42V
(RV888D/RV999D)
C381 1-136-497-81 FILM 0.1uF 5% 50V
(RV888D/RV999D)
C382 1-136-497-81 FILM 0.1uF 5% 50V
(RV888D/RV999D)
C383 1-136-497-81 FILM 0.1uF 5% 50V
(RV888D/RV999D)
C384 1-136-497-81 FILM 0.1uF 5% 50V
(RV888D/RV999D)
C385 1-136-497-81 FILM 0.1uF 5% 50V
(RV888D/RV999D)
C386 1-136-497-81 FILM 0.1uF 5% 50V
(RV888D/RV999D)
< CONNECTOR >
CN302 1-785-318-11 PIN, CONNECTOR (STRAIGHT) 6P
(RV888D/RV999D)
CN372 1-564-506-11 PLUG, CONNECTOR 3P (RV888D/RV999D)
< DIODE >
D301 8-719-991-33 DIODE 1SS133T-77 (RV888D/RV999D)
D341 8-719-991-33 DIODE 1SS133T-77 (RV888D/RV999D)
D351 8-719-991-33 DIODE 1SS133T-77 (RV888D/RV999D)
D371 8-719-510-68 DIODE D5SBA204101 (RV888D/RV999D)
D381 8-719-991-33 DIODE 1SS133T-77 (RV888D/RV999D)
D382 8-719-991-33 DIODE 1SS133T-77 (RV888D/RV999D)
D391 8-719-991-33 DIODE 1SS133T-77 (RV888D/RV999D)
D491 8-719-991-33 DIODE 1SS133T-77 (RV888D/RV999D)
< IC >
IC301 6-600-361-01 IC STK403-250A (RV888D/RV999D)
< COIL >
L381 1-422-009-13 COIL, AIR-CORE (RV888D/RV999D)
L382 1-422-009-13 COIL, AIR-CORE (RV888D/RV999D)
L383 1-422-009-13 COIL, AIR-CORE (RV888D/RV999D)
< TRANSISTOR >
Q301 8-729-140-84 TRANSISTOR 2SC1841-PAFAEA
(RV888D/RV999D)
Q316 8-729-140-84 TRANSISTOR 2SC1841-PAFAEA
(RV888D/RV999D)
Q317 8-729-119-78 TRANSISTOR 2SC2785-HFE
(RV888D/RV999D)
Q341 8-729-140-84 TRANSISTOR 2SC1841-PAFAEA
(RV888D/RV999D)
Q351 8-729-140-84 TRANSISTOR 2SC1841-PAFAEA
(RV888D/RV999D)
Q381 8-729-026-39 TRANSISTOR 2SA933AS-QT
(RV888D/RV999D)
Q383 8-729-026-39 TRANSISTOR 2SA933AS-QT
(RV888D/RV999D)
Q384 8-729-029-66 TRANSISTOR DTC114ESA (RV888D/RV999D)
< RESISTOR >
R301 1-247-831-11 CARBON 1K 5% 1/4W
(RV888D/RV999D)
R302 1-247-871-11 CARBON 47K 5% 1/4W
(RV888D/RV999D)
R303 1-249-416-11 CARBON 820 5% 1/4W
(RV888D/RV999D)
R304 1-247-871-11 CARBON 47K 5% 1/4W
(RV888D/RV999D)
0R305 1-245-235-21 METAL 0.22 10% 2W F
(RV888D/RV999D)
R307 1-247-831-11 CARBON 1K 5% 1/4W
(RV888D/RV999D)
R308 1-249-431-11 CARBON 15K 5% 1/4W
(RV888D/RV999D)
R309 1-247-879-11 CARBON 100K 5% 1/4W
(RV888D/RV999D)
R310 1-260-076-11 CARBON 10 5% 1/2W F
(RV888D/RV999D)
0R311 1-212-881-11 FUSIBLE 100 5% 1/4W F
(RV888D/RV999D)
R314 1-249-427-11 CARBON 6.8K 5% 1/4W
(RV888D/RV999D)
R315 1-247-863-11 CARBON 22K 5% 1/4W
(RV888D/RV999D)
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
SURROUND AMP
116
HCD-RV777D/RV888D/RV999D
SURROUND AMP SW TRANS
R316 1-247-879-11 CARBON 100K 5% 1/4W
(RV888D/RV999D)
R317 1-247-879-11 CARBON 100K 5% 1/4W
(RV888D/RV999D)
R318 1-249-429-11 CARBON 10K 5% 1/4W
(RV888D/RV999D)
R319 1-247-879-11 CARBON 100K 5% 1/4W
(RV888D/RV999D)
0R320 1-202-972-61 FUSIBLE 1 5% 1/4W F
(RV888D/RV999D)
0R321 1-202-972-61 FUSIBLE 1 5% 1/4W F
(RV888D/RV999D)
R331 1-247-871-11 CARBON 47K 5% 1/4W
(RV888D/RV999D)
R332 1-247-873-11 CARBON 56K 5% 1/4W
(RV888D/RV999D)
R333 1-249-439-11 CARBON 68K 5% 1/4W
(RV888D/RV999D)
R341 1-247-831-11 CARBON 1K 5% 1/4W
(RV888D/RV999D)
R342 1-247-871-11 CARBON 47K 5% 1/4W
(RV888D/RV999D)
R343 1-249-416-11 CARBON 820 5% 1/4W
(RV888D/RV999D)
R344 1-247-871-11 CARBON 47K 5% 1/4W
(RV888D/RV999D)
0R345 1-245-235-21 METAL 0.22 10% 2W F
(RV888D/RV999D)
R347 1-247-831-11 CARBON 1K 5% 1/4W
(RV888D/RV999D)
R348 1-249-431-11 CARBON 15K 5% 1/4W
(RV888D/RV999D)
R349 1-247-879-11 CARBON 100K 5% 1/4W
(RV888D/RV999D)
R350 1-260-076-11 CARBON 10 5% 1/2W F
(RV888D/RV999D)
R351 1-247-831-11 CARBON 1K 5% 1/4W
(RV888D/RV999D)
R352 1-247-871-11 CARBON 47K 5% 1/4W
(RV888D/RV999D)
R353 1-249-416-11 CARBON 820 5% 1/4W
(RV888D/RV999D)
R354 1-247-871-11 CARBON 47K 5% 1/4W
(RV888D/RV999D)
0R355 1-245-235-21 METAL 0.22 10% 2W F
(RV888D/RV999D)
R357 1-247-831-11 CARBON 1K 5% 1/4W
(RV888D/RV999D)
R358 1-249-431-11 CARBON 15K 5% 1/4W
(RV888D/RV999D)
R359 1-247-879-11 CARBON 100K 5% 1/4W
(RV888D/RV999D)
R360 1-260-076-11 CARBON 10 5% 1/2W F
(RV888D/RV999D)
R373 1-247-879-11 CARBON 100K 5% 1/4W
(RV888D/RV999D)
R374 1-247-879-11 CARBON 100K 5% 1/4W
(RV888D/RV999D)
R381 1-260-076-11 CARBON 10 5% 1/2W F
(RV888D/RV999D)
R382 1-260-076-11 CARBON 10 5% 1/2W F
(RV888D/RV999D)
R383 1-260-076-11 CARBON 10 5% 1/2W F
(RV888D/RV999D)
R385 1-260-076-11 CARBON 10 5% 1/2W F
(RV888D/RV999D)
R386 1-260-076-11 CARBON 10 5% 1/2W F
(RV888D/RV999D)
R390 1-249-429-11 CARBON 10K 5% 1/4W
(RV888D/RV999D)
R391 1-260-076-11 CARBON 10 5% 1/2W F
(RV888D/RV999D)
0R394 1-216-451-11 METAL OXIDE 120 5% 2W F
(RV888D/RV999D)
R395 1-249-429-11 CARBON 10K 5% 1/4W
(RV888D/RV999D)
R396 1-247-863-11 CARBON 22K 5% 1/4W
(RV888D/RV999D)
R397 1-247-831-11 CARBON 1K 5% 1/4W
(RV888D/RV999D)
R398 1-247-863-11 CARBON 22K 5% 1/4W
(RV888D/RV999D)
0R399 1-216-451-11 METAL OXIDE 120 5% 2W F
(RV888D/RV999D)
< RELAY >
RY381 1-515-920-11 RELAY (RV888D/RV999D)
RY382 1-515-920-11 RELAY (RV888D/RV999D)
< THERMISTOR >
TH301 1-807-796-11 THERMISTOR (RV888D/RV999D)
< TERMINAL BOARD >
TM401 1-694-674-22 TERMINAL BOARD (6P) (SURROUND SPEAKER,
CENTER SPEAKER) (RV888D/RV999D)
*************************************************************
1-687-669-12 SW BOARD
**********
< SWITCH >
S751 1-786-514-11 SWITCH, LEVER (SLIDE)
(OPEN/CLOSE DETECT)
*************************************************************
A-1053-996-A TRANS BOARD, COMPLETE (AUS)
A-1053-997-A TRANS BOARD, COMPLETE (E51)
A-1053-998-A TRANS BOARD, COMPLETE (MX)
A-1053-999-A TRANS BOARD, COMPLETE (AR)
A-4751-863-A TRANS BOARD, COMPLETE
(RV888D:EXCEPT AUS/
RV999D:EXCEPT E51,AUS,AR,MX)
A-4751-866-A TRANS BOARD, COMPLETE (RV777D)
**********************
1-533-217-41 HOLDER, FUSE
< CAPACITOR >
C912 1-126-960-11 ELECT 1uF 20% 50V
C913 1-126-968-11 ELECT 100uF 20% 50V
C915 1-164-159-11 CERAMIC 0.1uF 50V
C918 1-128-576-11 ELECT 100uF 20% 63V
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
117
HCD-RV777D/RV888D/RV999D
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
< CONNECTOR >
*CN913 1-564-518-11 PLUG, CONNECTOR 3P (RV888D/RV999D)
*CN914 1-564-525-11 PLUG, CONNECTOR 10P
*CN915 1-564-519-11 PLUG, CONNECTOR 4P
< DIODE >
D911 6-500-522-11 DIODE 10EDB40-TA2B5
D912 8-719-982-19 DIODE MTZJ-30A
D913 8-719-118-67 DIODE RD6.2F-T7B3
< TRANSISTOR >
Q971 8-729-140-97 TRANSISTOR 2SB734-34
< RESISTOR >
0R911 1-217-637-00 FUSIBLE 1 5% 1/4W F
R914 1-249-429-11 CARBON 10K 5% 1/4W
R915 1-247-807-31 CARBON 100 5% 1/4W
R916 1-247-807-31 CARBON 100 5% 1/4W
R938 1-249-429-11 CARBON 10K 5% 1/4W
*************************************************************
A-4751-861-A VIDEO BOARD, COMPLETE
**********************
7-685-872-09 SCREW +BVTT 3X8 (S)
< CAPACITOR >
C800 1-104-655-11 ELECT 470uF 20% 6.3V
C801 1-162-306-11 CERAMIC 0.01uF 20% 16V
C802 1-126-960-11 ELECT 1uF 20% 50V
C804 1-126-960-11 ELECT 1uF 20% 50V
C805 1-162-282-31 CERAMIC 100PF 10% 50V
C806 1-126-960-11 ELECT 1uF 20% 50V
C807 1-104-658-11 ELECT 100uF 20% 10V
C808 1-162-306-11 CERAMIC 0.01uF 20% 16V
C809 1-162-282-31 CERAMIC 100PF 10% 50V
C810 1-162-282-31 CERAMIC 100PF 10% 50V
C811 1-162-282-31 CERAMIC 100PF 10% 50V
C812 1-126-960-11 ELECT 1uF 20% 50V
C813 1-162-282-31 CERAMIC 100PF 10% 50V
C814 1-126-960-11 ELECT 1uF 20% 50V
C816 1-126-960-11 ELECT 1uF 20% 50V
C818 1-126-916-11 ELECT 1000uF 20% 6.3V
C821 1-126-916-11 ELECT 1000uF 20% 6.3V
C824 1-126-916-11 ELECT 1000uF 20% 6.3V
C827 1-126-916-11 ELECT 1000uF 20% 6.3V
C830 1-126-916-11 ELECT 1000uF 20% 6.3V
C833 1-164-159-11 CERAMIC 0.1uF 50V
C836 1-126-964-11 ELECT 10uF 20% 50V
C837 1-162-282-31 CERAMIC 100PF 10% 50V
C838 1-162-306-11 CERAMIC 0.01uF 20% 16V
C839 1-104-658-11 ELECT 100uF 20% 10V
C840 1-162-282-31 CERAMIC 100PF 10% 50V
C841 1-104-655-11 ELECT 470uF 20% 6.3V
C851 1-126-923-11 ELECT 220uF 20% 10V
C852 1-126-956-11 ELECT 0.1uF 20% 50V
C860 1-126-942-61 ELECT 1000uF 20% 25V
C861 1-117-245-11 ELECT 330uF 20% 6.3V
C862 1-128-646-11 ELECT 1000uF 20% 6.3V
C863 1-117-317-11 ELECT 1000uF 20% 25V
C871 1-117-245-11 ELECT 330uF 20% 6.3V
C872 1-128-646-11 ELECT 1000uF 20% 6.3V
C873 1-117-317-11 ELECT 1000uF 20% 25V
C876 1-117-245-11 ELECT 330uF 20% 6.3V
C877 1-117-245-11 ELECT 330uF 20% 6.3V
< CONNECTOR >
CN801 1-784-213-11 CONNECTOR, FFC (LIF(NON-ZIF)) 15P
CN802 1-785-328-11 PIN, CONNECTOR (LIGHT ANGLE) 2P
*CN804 1-564-731-11 PIN, CONNECTOR (SMALL TYPE) 15P
CN805 1-779-273-11 CONNECTOR, FFC (LIF(NON-ZIF)) 5P
< DIODE >
D838 8-719-991-33 DIODE 1SS133T-77
D861 8-719-210-21 DIODE 11EQS04
D871 8-719-210-21 DIODE 11EQS04
< GROUND TERMINAL BOARD >
EP801 1-537-771-21 TERMINAL BOARD, GROUND
EP802 1-537-771-21 TERMINAL BOARD, GROUND
< COIL >
FB835 1-412-473-21 INDUCTOR (SMALL TYPE)
< IC >
IC801 6-705-602-01 IC MM1623BFBE
IC802 8-759-295-90 IC NJM2244M-TE2
IC803 8-759-231-53 IC TA7805S
IC804 8-759-659-28 IC SI-8033S
IC805 8-759-474-09 IC SI-8050S-LF1101
< JACK >
J801 1-817-449-11 JACK, PIN 3P (COMPONENT VIDEO OUT)
J802 1-794-970-11 JACK, PIN 1P (VIDEO OUT)
J803 1-537-943-11 CONNECTOR (DIN) 1P (S VIDEO OUT)
< COIL >
L800 1-410-470-11 INDUCTOR 10uH
L861 1-456-513-11 COIL, CHOKE 150uH
L862 1-410-397-21 INDUCTOR, FERRITE BEAD
L871 1-456-513-11 COIL, CHOKE 150uH
L872 1-414-741-11 INDUCTOR 10uH
< TRANSISTOR >
Q851 8-729-029-21 TRANSISTOR DTA114ESA-TP
Q852 8-729-029-66 TRANSISTOR DTC114ESA
Q853 8-729-029-66 TRANSISTOR DTC114ESA
Q855 8-729-029-66 TRANSISTOR DTC114ESA
Q857 8-729-029-66 TRANSISTOR DTC114ESA
< RESISTOR >
R803 1-249-429-11 CARBON 10K 5% 1/4W
R815 1-249-429-11 CARBON 10K 5% 1/4W
R818 1-247-804-11 CARBON 75 5% 1/4W
R821 1-247-804-11 CARBON 75 5% 1/4W
R824 1-247-804-11 CARBON 75 5% 1/4W
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
VIDEOTRANS
118
HCD-RV777D/RV888D/RV999D
R827 1-247-804-11 CARBON 75 5% 1/4W
R831 1-249-429-11 CARBON 10K 5% 1/4W
R833 1-247-804-11 CARBON 75 5% 1/4W
R834 1-249-429-11 CARBON 10K 5% 1/4W
R835 1-249-429-11 CARBON 10K 5% 1/4W
R836 1-247-847-11 CARBON 4.7K 5% 1/4W
R837 1-247-871-11 CARBON 47K 5% 1/4W
R838 1-249-403-11 CARBON 68 5% 1/4W
R839 1-247-879-11 CARBON 100K 5% 1/4W
R840 1-247-879-11 CARBON 100K 5% 1/4W
R850 1-247-807-31 CARBON 100 5% 1/4W
R851 1-249-429-11 CARBON 10K 5% 1/4W
*************************************************************
MISCELLANEOUS
***************
21-828-965-11 WIRE (FLAT TYPE) (11 CORE)
52 1-796-487-61 DECK, MECHANICAL
56 1-828-974-11 WIRE (FLAT TYPE) (13 CORE)
58 1-828-338-11 WIRE (FLAT TYPE) (15 CORE)
202 1-828-895-11 WIRE (FLAT TYPE) (15 CORE)
203 1-828-288-11 WIRE (FLAT TYPE) (5 CORE)
204 1-828-333-11 WIRE (FLAT TYPE) (13 CORE) (RV777D)
204 1-828-393-11 WIRE (FLAT TYPE) (25 CORE)
0253 1-696-848-22 CORD, POWER (AUS)
0253 1-751-520-21 CORD, POWER (EA)
0253 1-777-071-83 CORD, POWER (E51,PH,SP,MY)
0253 1-783-941-22 CORD, POWER (AR)
0253 1-827-226-11 CORD, POWER (E3,E15,MX)
302 1-776-182-11 WIRE (FLAT TYPE) (5 CORE)
373 1-824-106-12 CABLE, FLEXIBLE FLAT (24 CORE)
374 1-828-672-11 WIRE (FLAT TYPE) (29 CORE)
0F911 1-533-472-12 FUSE, GLASS TUBE (DIA.5) (5A/250V)
(EXCEPT AUS,AR,MX)
0F912 1-533-472-12 FUSE, GLASS TUBE (DIA.5) (5A/250V)
(EXCEPT AUS,AR,MX)
0F913 1-533-472-12 FUSE, GLASS TUBE (DIA.5) (5A/250V)
(RV888D:AUS/RV999D:AUS,AR)
0F913 1-533-473-12 FUSE, GLASS TUBE (DIA.5) (6.3A/250V)
(RV777D)
0F913 1-576-655-12 FUSE, GLASS TUBE (DIA.5) (8A/250V)
(RV888D:EXCEPT AUS/
RV999D:EXCEPT AUS,AR)
0F914 1-533-473-12 FUSE, GLASS TUBE (DIA.5) (6.3A/250V)
0F915 1-533-473-12 FUSE, GLASS TUBE (DIA.5) (6.3A/250V)
0F916 1-533-473-12 FUSE, GLASS TUBE (DIA.5) (6.3A/250V)
(RV888D/RV999D)
0F917 1-533-473-12 FUSE, GLASS TUBE (DIA.5) (6.3A/250V)
(RV888D/RV999D)
0F918 1-533-471-12 FUSE, GLASS TUBE (DIA.5) (4A/250V)
(RV777D)
0F918 1-533-472-12 FUSE, GLASS TUBE (DIA.5) (5A/250V)
(RV888D/RV999D)
0F919 1-533-471-12 FUSE, GLASS TUBE (DIA.5) (4A/250V)
FAN901 1-763-072-11 FAN, DC
FC901 1-500-386-11 FILTER, CLAMP (FERRITE CORE) (AUS,EA)
IC921 8-759-518-68 IC PQ12RF21
IC922 8-759-701-59 IC NJM78M09FA
IC923 8-759-701-59 IC NJM78M09FA
IC932 6-703-546-01 IC TA7804LS
IC934 8-759-231-53 IC TA7805S
M741 A-4723-963-A MOTOR ASSY, TABLE (TABLE)
M751 A-4736-655-A MOTOR ASSY, LOADING (LOADING)
RE701 1-477-680-12 ENCODER, ROTARY
(DISC TRAY ADDRESS DETECT)
0T911 1-443-174-11 TRANSFORMER, POWER (RV777D:EXCEPT EA)
0T911 1-443-175-11 TRANSFORMER, POWER (RV777D:EA)
0T911 1-443-352-11 TRANSFORMER, POWER
(RV888D:EXCEPT EA/RV999D:EXCEPT EA,MX)
0T911 1-443-362-11 TRANSFORMER, POWER
(RV888D:EA/RV999D:EA,MX)
TM901 1-693-603-31 TUNER PACK (FM/AM) (ANTENNA)
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
VIDEO
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
119
HCD-RV777D/RV888D/RV999D
MEMO
120
HCD-RV777D/RV888D/RV999D
REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper on the revised page allows you to jump to the next revised page.
Ver. Date Description of Revision
1.0 2004. 06 New

Navigation menu