ImproX IXP220 Controller IXP2200Controller

User Manual: IXP2200Controller

Open the PDF directly: View PDF .
Page Count: 4

The ImproX IXP220 Controller is a fully featured

Controller forming part of the IXP220 Software

System. The IXP220 Controller’s applications

include access control and alarm control.

Consisting of a single hardware platform, the

ImproX IXP220 Controller is available in a mild

steel cabinet or, if preferred, in an open frame

construction. The Controller is delivered as

standard with all hardware components thus

enabling full functionality.

Communication options include Ethernet, USB,

RS485 or RS232 and memory capacity is ensured

up to 10 000 Tags and 100 000 buffered

Transactions.

Features include anti-tamper and a general relay

for power control or alarm arming. The remaining

relay and digital inputs allow each Reader support

for a Door Open Sensor and Request to Enter or

Exit.

Six available feature models address market needs

from single door to multiple remote sites with up to

256 anti-passback doors. The IXP220 Controller is

easily upgraded from a Stand-alone Controller to a

System Controller through a soft unlock system.

 2 Reader Fixed Addresses, offering connection of up to 2 Antenna

Readers OR 2 Wiegand Readers.

 IXP220-1 stores up to 1 000 Tags and up to 10 000 buffered

Transactions.

 IXP220-2 stores up to 2 000 Tags and up to 10 000 buffered

Transactions.

 IXP220-3 and IXP220-4 store up to 10 000 Tags and up to 100 000

buffered Transactions.

 Communication options include Ethernet, USB, RS485 or RS232.

 On-board Battery charging circuit (up to 7 Ahr when using a 12 V

Sealed Lead Acid Battery).

 In-field Firmware upgrades.

 Four Digital Inputs let you interface with a variety of devices such as

reed switches and push-buttons. When used with the IXP220

Software these Digital Inputs can perform specific tasks such as:

 Door Open Sensing (DOS) with End of Line (EOL) Sensing.

 Request to Exit (RTE).

 A 16 V AC (40 VA) Transformer providing 2 A to power the Controller

and charge a 12 V 7 Ahr Sealed Lead Acid Battery.

 Automatic switch-over to Battery operation on Mains Failure.

 Mild Steel Cabinet, accommodating the Transformer, IXP220

Controller and Battery.

 Uses Quick Click Glands.

 1 Anti-tamper Switch.

 Provides the IXP220 Controller with TCP/IP connectivity without

requiring any additional network cable or router infrastructure.

 Using a GSM network, The ImproX GSM Module allows you to:

 Contact a remote IXP220 Controller.

 Program an IXP220 Controller without removing it from the

remote location.

 Download transactions from an IXP220 Controller installed at a

remote site.

ISC96X Open Frame Construction

Length

200 mm (8 in).

Width

123 mm (5 in).

Height

31 mm (1 in).

Approximate Weight

580 g (20 oz).

IPS96X Power Supply Combo

Length

305 mm (12 in).

Width

295 mm (11 in).

Height

77 mm (3 in).

Approximate Weight

3 kg (7 lb) excluding Controller or

Battery.

Cabinet Material

Mild Steel.

Colour

Black.

ImproX GSM Module (Optional Extra)

Approximate Weight

(GSM900)

65 g (2.29 oz) including Antenna.

Approximate Weight

(GSM901)

15.4 g (0.5 oz).

Operating Temperature

-25oC to +60oC (-13oF to +140oF).

Storage Temperature

-40oC to +80oC (-40oF to +176oF).

Humidity Range

0 to 95% relative humidity at +40oC

(+104oF) non-condensing.

Approvals

CE Approval

(ISC96X and IPS96X)

EN301 489-1 and EN301 489-3.

CE Health and Safety

Certification (ISC96X and

IPS96X)

SANS 60950-1:2003 and

IEC 60950-1:2001.

ISC960-1-0-GB-XX ISC962-1-0-GB-XX IPS960-1-0-GB-XX

IPS961-1-0-GB-XX IPS962-1-0-GB-XX IPS963-1-0-GB-XX

GSM900-0-6-GB-XX GSM901-0-0-GB-XX

XXX9XX-X-X-GB-XX

Page 2

Approvals (Continued)

CE Approval

(GSM900 and GSM901)

Pending.

FCC Approval

Pending.

Dust & Splash Resistance

(ISC96X)

Designed to work in an indoor (dry)

environment. The Controller is NOT

sealed against water.

Dust & Splash Resistance

(IPS96X)

Designed to work in an indoor (dry)

environment similar to IP20. The

Power Supply Combo is, therefore, not

sealed against water.

Drop Endurance

(ISC96X, IPS96X,

GSM900 and GSM901)

1 m (3.28 ft) drop (in packaging).

ISC96X Open Frame Construction

Power Input

Main Power Input Port

18 V DC to 32 V DC or 16 V AC to

24 V AC.

Battery Input Port

12 V DC to 14 V DC.

Typical Current Distribution

Controller

Current (mA)

Power (W)

12 V DC with no

peripherals connected

and relays off

1.08

24 V DC with no

peripherals connected

and relays off

1.4

16 V AC with no

peripherals connected

and relays off

1.1

Battery Charging

350 mA Trickle charge at 13.7 V DC

maximum.

External Readers

200 mA continuous at 5 V DC and 12

V DC maximum per port.

Power Output Port

1 A continuous at 12 V DC to 14 V DC

maximum.

Power Input Protection

Over-voltage and over-current

protection are provided on the Main

Power Input.

NOTE: EMC emissions only apply when using the main Power Input Port.

NOTE: As an alternative to a battery, power the IXP220 using a 12 V DC

uninterrupted power supply connected using the Battery Input.

NOTE: The Power Output Port provides a nominal 12 to 14 V DC at 1 A

continuous current. When using the 12 V Backup Battery, the

output provides up to 3 A briefly to cater for in rush currents into

locks and other equipment. When using the Controller without the

12 V Backup Battery, then any load that demands more than 3 A

from the Power Output Port can cause the IXP220 to protect

against overload. The Controller achieves this by indefinitely

entering Total Shutdown Mode. Once the overload is removed,

the IXP220 resumes normal operation after a maximum of 3

seconds.

IPS96X Power Supply Combo

Transformer

NOTE: An integrated transformer supplies power to this model IXP220

Controller. The Typical Current Distribution for the Open Frame

Construction applies.

Input Voltage

230 V AC (nominal) at 50 Hz to 60 Hz.

Output Voltage

16 V AC.

Output Current

2 A maximum.

The following specifications are common to the Open Frame

Construction and the Power Supply Combo options:

Battery

Type

12 V Sealed Lead Acid Battery, 7 Ahr

(Max).

Length

151 mm (6 in) (Max).

Width

65 mm (3 in) (Max).

Battery (Continued)

Height

99 mm (4 in) including the Terminals

(Max).

Charge Voltage

13.8 V DC at 350 mA (Max).

Real Time Clock Backup Battery (RTC)

Battery Type

1 x 3 V, CR2032, Lithium cell battery.

Battery Life

1 year with power OFF,

5 years with Power ON,

5 years Storage with Battery Tab in

place.

USB Port

Connection

USB Device, Type-B, female

connector, 12 Mbps, USB V2.0.

Ethernet Port

Connection

Standard Ethernet RJ45 connector.

10/100 Base T, half or full duplex.

RS232 Port

Connection

9-Way, D-type, female connector or

terminal block connection.

NOTE: To achieve RS232 connection, use either the 9-way, D-type,

female connector OR the terminal block connection.

Default Baud Rate

38 400.

RS485 Controller Port

Electrical Interface

RS485.

Default Baud Rate

38 400.

Data Format

8 data bits, no parity, 1 stop bit.

Communications Protocol

ImproX Secure Communications

Protocol.

Line Termination (RS485)

Provision is made for line termination.

GSM Module (GSM900)

Frequency

850 MHz, 900 MHz, 1 800 MHz and

1 900 MHz.

Minimum Power

Consumption

0.05 W.

Operating Power

Consumption

1.5 W.

Peak Power Consumption

7.5 W.

Electrical Interface

RS485.

Baud Rate

38 400.

Data Format

8 data bits, no parity, 1 stop bit.

Communications Protocol

ImproX Secure Communications

Protocol.

Line Termination

Provision is made for line termination.

Antenna Port

2 Fully functional Antenna Reader

Ports.

Wiegand Port

Power Output

12 V DC or 5 V DC (selectable) at

maximum 200 mA.

Modes Supported

Tag, Tag + PIN-code, Personal Access

Code or Reason Code Mode except

when the Reader Port is set to

Wiegand Open Mode.

Input Type

4 x Dry Contact Digital Inputs.

Detection Resistance

Range

< 2 kOhm.

Protection Range

+20 V continuous.

Page 3

Relay Output

2 x Relays, Form C, each with NO,

COM and NC contacts.

Contact Ratings

10 A at 28 V DC,

5 A at 220 V AC,

12 A at 120 V AC.

Operations

100 000 Minimum.

Alarm Signal

IN: Dry Contact Digital Input.

GND: Ground reference.

OUT: Open Collector Digital Output.

Alarm Relay

Relay Output

1 x Relay, Form C with NO, COM and

NC contacts.

Contact Ratings

10 A at 28 V DC,

5 A at 220 V AC,

12 A at 120 V AC.

SD Card Adaptor

Reserved for future use.

Standard 9-Pin SD Mode Interface,

2 GB max.

Anti-tamper Switch

1 Switch, detects opening of the Top

Cover on the Power Supply combo

model. No anti-tamper is supplied on

the open frame Controller.

Baud Rate

Factory-set to 38 400.

Beep Codes

Fails Power-on Self-test

Single long beep of 2 second duration.

Passes Power-on Self-

test

Two short beeps of 200 ms duration,

separated by a 200 ms inter-beep

pause.

Characters

16 Characters by 4 lines.

Character Sets

English, Katakana.

Contrast

Adjustable using the Trimpot.

Back-lighting

Turned on and off via the

Communications Protocol.

Buttons

12 Alphanumeric and function keys.

Back-lighting

Yes.

NOTE: The LCD and Keypad back-lighting operate independently of each

other.

Status Indicator

Status LED

Power applied to the Controller

indicated by steady Red LED

(internally visible).

Diagnostic Indicators

Incoming RS485 Data

Flashing Green LED (internally visible).

Outgoing RS485 Data

Flashing Red LED (internally visible).

Incoming RS232 Data

Flashing Green LED (internally visible).

Outgoing RS232 Data

Flashing Red LED (internally visible).

Speed LED (Ethernet)