Instruction 5c40e2145bce4efbaea58eea60a83989
2018-11-19
: Instruction 5C40E2145Bce4Efbaea58Eea60A83989 instruction_5c40e2145bce4efbaea58eea60a83989 instruction upload
Open the PDF directly: View PDF 
.
Page Count: 4
Introduction
IronWolf Health Management (IHM) is an embedded software
designed on the tenets of prevention, intervention and recovery.
It aims to manage the health of the drive through the useful life,
and provide ease of data recovery should a catastrophic event
damage the drive and render it nonfunctional.
To provide this functionality, IHM analyzes several parameters
related to drive health and uses proprietary algorithms to
determine their impact to drive health. With this output and info
on additional operating conditions, such as temperature, humidity,
etc., IHM recommends preventive actions to users to avoid any
drive damage. It may also recommend specic interventions when
the drive health is likely to have been impacted.
Finally, it provides seamless linkage within the UI to Seagate®
Rescue and Recovery plans, ensuring users have complete peace
of mind in using their IronWolf™ drive in their NAS box.
Coverage
The following Seagate IronWolf and IronWolf Pro drives are IHM enabled as of February 2017.
Refer to Seagate IHM or Synology web pages for the most current list of supported capacities.
IronWolf™ Health Management
SUPPORT DOCUMENT
IronWolf model numbers
• ST4000VN008
• ST6000VN0041
• ST7000VN002
• ST8000VN0022
• ST8000VN0004
• ST10000VN0004
1
IronWolf Pro model numbers
• ST4000NE0025
• ST6000NE0021
• ST8000NE0021
• ST8000NE0004
• ST10000NE0004
1
Exclusions
The following drives are not IHM enabled:
• All non-Seagate drives
• All 3.5-inch Enterprise Capacity
drives, Desktop, BarraCuda®,
BarraCuda Pro, Surveillance,
SkyHawk™, FireCuda™ drives
• All legacy NAS HDDs
1 10TB IronWolf and IronWolf Pro with supported Synology NAS models will be enabled by C1Q17.
Series Supported Synology NAS Model1
x17 Series RS217, RS3617xs, RS18017xs+, RX1217(RP), RX1217sas
x16 Series DS116, DS216se, DS216j, DS216, DS216play, DS216+, DS216+II, DS416j, DS416, DS416play,
DS716+, DS716+II, DS916+, RS816, RS2416+/RS2416RP+, RS18016xs+, NVR216, RX1216sas
x15 Series DS115j, DS115, DS215j, DS215+, DS415play, DS415+, DS715, DS1515, DS1515+, DS1815+,
DS2015xs, DS2415+, DS3615xs, DX1215, RS815, RS815+/RS815RP+, RX415
x14 Series DS114, DS214se, DS214, DS214play, DS214+, DS414j, DS414, RS214, RS814, RS814+/RS814RP+,
RS2414+/RS2414RP+, RS3614xs/RS3614RPxs, RS3614xs+, RX1214(RP)
x13 Series DS213j, DS213air, DS213, DS213+, DS413j, DS713+, DS1513+, DS1813+, DS2413+, DX513,
RS3413xs+, RS10613xs+, RX1213sas
x12 Series DS112j, DS112, DS112+, DS212j, DS212, DS212+, DS412+, DS712+, DS1512+, DS1812+,
DS3612xs, RS212, RS812, RS812+/RS812RP+, RS2212+/RS2212RP+, RS3412xs/RS3412RPxs
x11 Series DS111, DS211j, DS211, DS211+,DS411, DS411+, DS411+II, DS1511+, DS2411+,
DS3611xs, RS411, RS2211+/RS2211RP+, RS3411xs/RS3411RPxs, DX1211
Synology Systems with DiskStation Manager (DSM) 6.1
Expected Out-of-Box Behavior
Right out of the box, the NAS system is likely unpopulated. If so, once the user inserts a drive in the
NAS bay, DSM 6.1 will automatically detect that both NAS box and drive are supported with IHM, and
will display one of the following messages to the user:
This drive is a Seagate IronWolf drive. Please purchase your preferred
Seagate Rescue Data Recovery Plan here.
In the option above, the user has inserted an IronWolf drive and will be guided to the Seagate Data
Rescue and Recovery Plans.
SUPPORT DOCUMENT - IRONWOLF HEALTH MANAGEMENT
1 10TB IronWolf and IronWolf Pro with supported Synology NAS models will be enabled by C1Q17.
Category Code Synology UI Message (Warning)
Normal 000 Normal
Prevention
100
Abnormally high operating temperature has been detected. Make sure that the
rear ventilation ports are not blocked, and try to lower the ambient temperature.
If the temperature is still high, go to Control Panel > Hardware & Power > Fan
Speed Mode to change the fan operation to a higher speed. If this issue persists,
contact Synology Support Team.
101
Connection issues on your _DISKSTATION_ and hard drive interface have been
detected. Make sure the hard drive is properly installed in the chassis or drive
tray, and that the tray properly installed in your _DISKSTATION_. If this issue
persists, contact Synology Support Team.
102
Excessive physical shock to the hard drive has been detected. Make sure your
hard drive and _DISKSTATION_ are placed on a stable surface. If this issue per-
sists, contact Synology Support Team.
105 Excessive vibration has been detected. Make sure your _DISKSTATION_ is
placed on a stable surface. If this issue persists, contact Synology Support Team.
106
Excessive host resets have been detected. Make sure the hard drive is properly
installed in the chassis or drive tray. Performing a power cycle is recommended.
If this issue persists, contact Synology Support Team.
Intervention ≥200
To check the health status of the hard drive, it is recommended to run the
S.M.A.R.T. extended test on the drive. If this issue persists, contact the drive
reseller or manufacturer.
IHM Output Codes
IHM can be scheduled to run on a regular basis through the DSM 6.1 User Interface. It can also be run
manually at any point the user desires. It is recommended that the frequency be set at ≥12 hrs. Each
time IHM is run, one of the following output codes may appear:
This Seagate IronWolf Pro drive comes with a 2-year complimentary
Rescue Data Recovery Service. Please register here.
In this option, the user has inserted an IronWolf Pro drive and will be guided to the Seagate Product
Registration page. Post-registration, they will be notied that their IronWolf Pro drive is eligible for a
complimentary 2-year Data Recovery Plan. They will also be presented options to extend this coverage
for an additional one to three years.
SUPPORT DOCUMENT - IRONWOLF HEALTH MANAGEMENT
S.M.A.R.T. IronWolf Health Management
Monitors 20 drive parameters Monitors in excess of 200 drive parameters that may
inuence drive health
Reports Pass or Fail status Noties user of possible prevention and intervention
actions ahead of a Fail event, thereby reducing the
probability of catastrophic failure and associated data loss
Reports end impact to drive through monitoring of 20
drive parameters with xed thresholds
Reports end impact to drive, but also communicates
failure mode through output code (for interpretation by
STX Customer Care only)
Has no memory of past trends of threshold excursions Maintains moving window of parametric data for
trend analysis and assesses impact of external
stresses over the drive life
IHM vs S.M.A.R.T.
seagate.com
AMERICAS Seagate Technology LLC 10200 South De Anza Boulevard, Cupertino, California 95014, United States, 408-658-1000
ASIA/PACIFIC Seagate Singapore International Headquarters Pte. Ltd. 7000 Ang Mo Kio Avenue 5, Singapore 569877, 65-6485-3888
EUROPE, MIDDLE EAST AND AFRICA Seagate Technology SAS 16–18, rue du Dôme, 92100 Boulogne-Billancourt, France, 33 1-4186 10 00
© 2017 Seagate Technology LLC. All rights reserved. Seagate, Seagate Technology and the Spiral logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries.
Barracuda, FireCuda, IronWolf and SkyHawk are either trademarks or registered trademarks of Seagate Technology LLC or one of its afliated companies in the United States and/or other countries. All
other trademarks or registered trademarks are the property of their respective owners. Seagate reserves the right to change, without notice, product offerings or specications. TP701.1-1703US, March 2017
IronWolf Health Management complements other health test related features within the NAS operating
system, such as Self-Monitoring, Analysis and Reporting Technology, or S.M.A.R.T.
SUPPORT DOCUMENT - IRONWOLF HEALTH MANAGEMENT
