IS QPP2788OZ

2017-08-30

: Is-Qpp2788Oz is-qpp2788oz images 708 p4dbimg

Open the PDF directly: View PDF PDF.
Page Count: 2

Package Contents
Pleasegoto forproductcleaningtips.Gotothe selection.
Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
www.quoizel.com Care + Maintenance
ToolsRequired:
LightSource:(1)A19MediumBaseBulb100WMaximum.
EstimatedAssembly Time:
Preparation:
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-QPP2788OZ
For Style QPP2788OZ
2016 QuoizelInc.
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Socket Collar
x1
A
C
Fixture Body
x1
Shade
x1
B
ReleasedDate:2016-08-12
STEP 2 Attach Mounting Screws,
Lock Washers and Hex Nuts to
Crossbar
-
A. Line up a set of holes on the Crossbar
(AA) and Holes on the Ceiling Canopy.
Thread Mounting Screws (DD) into the
holes on the Crossbar (AA). Pass Lock
Washers (BB) and thread Hex Nuts
(CC) onto the Mounting Screws (DD) .
Hand tighten until snug.
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
Hardware Contents
AA
BB
CC
Crossbar
x1
Lock Washer
x2
Hex Nut
x2
DD Mounting Screw
x2
EE Mounting Ball
x2
STEP 1 Adjust Fixture Height-
A. Unlock Set Screw on the
Coupling underside of Ceiling
Canopy with screwdrivers.
Push Wire in or pull wires out of
Ceiling Canopy according to
your desired hanging height.
Once your desired hanging
height is achieved, tighten Set
Screws on the Coupling until
snug.
B. Move Wire Clasp on the top end
of Wire until it is closed to hex
nut in the center of the Ceiling
Canopy.
Wire
Set Screw
Coupling
Ceiling
Canopy Wire Clasp
AFigure 1
AA
BB
CC
Ceiling
Canopy
DD
AA
Figure 2
STEP 3 -Attach Crossbar to Outlet
Box
A. Pass the supply wires through the
Crossbar (AA). Attach the Crossbar
(AA) to the Outlet Box with the head
of the Green Ground Screw facing
you. Secure it with Outlet Box
Screws (not included). Tighten until
snug.
Outlet Box
Outlet Box
Screws (not
included)
AA
Figure 3
Supply Wires
with Ground Wire
STEP 4 Fit Ceiling Canopy to Crossbar Assembly-
A. Fit the Ceiling Canopy to Mounting Screws (DD) and secure with
Mounting Balls (EE). Note: The Ceiling Canopy should be snug
against the ceiling and the Mounting Balls (EE). If not, adjust the
length of the Mounting Screws (DD) by unscrewing the Hex Nut
(CC) and Lock Washer (BB) and then screwing Mounting Screws
(DD) in or out of the Crossbar (AA) until the correct length is
achieved. Once the Ceiling Canopy is secure, remove the
Mounting Ball (EE) and Ceiling Canopy and proceed to Step 5.
Hex Nut and
Lock Washer
Figure 4
Ceiling
Canopy
AA
EE
DD
2of2
2016 QuoizelInc. ReleasedDate:2016-08-12
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
Wire Labeled
“N" from fixture
Wire Labeled
"L" from fixture
Green Striped
wire from fixture
White wire
from supply
Black wire from
supply (or Red)
Ground wire
from supply
STEP 5 Make Wire Connections-
Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
: If the electrical wire is going to be cut shorter than provided
you will need to identify the "L" line wire and the "N" wire before you
cut the excess wire off. One is labeled N and the other labeled L. The
third wire has a green stripe on it. To do this strip back the clear wire
covering the 3 fixture wires as far as you need to. This will expose
each fixture wire individually. Separate the "L" wire from the other
two and re-label the wire near where you want to make the cut. Be
sure to mark the wire on the side of the fixture and not on the excess
wire being cut and removed. Do the same labeling with the "N" wire.
A. Use standard wire connectors to make all wire connections.
(Connectors are not included with fixture.) Strip and prepare wire
ends according to instructions supplied with connectors.
Note
Figure 5
STEP 6 Install Ceiling Canopy to Ceiling-
A. Carefully tuck all wires into the outlet box and position the Ceiling
Canopy over the outlet box. Align the holes in the ceiling canopy
with the Mounting Screws (DD). Secure with Mounting Balls (EE)
and hand tighten until snug.
Ceiling
Canopy
AA
EE
DD
Figure 6
STEP 7 Install Shade and Bulb-
A. Place Shade (B) over socket and secure with Socket Collar (C).
Hand tighten until snug.
B. Insert bulb into socket and screw snugly into place.
Your fixture is now assembled and ready to use. Enjoy!
Socket
Figure 7
Bulb (not
supplied)
B
C
QPP2788OZ
FINISH: OLD BRONZE
HANGING HEIGHT
14” MIN. - 100” MAX.
OVERALL HEIGHT
12”
7.75” Dia.
9.75”
5” Dia.
NOTE: ALL DIMENSIONS ARE ROUNDED UP
TO THE NEAREST 1/4"

Navigation menu