JRP_Scan Select_Rx_Inst HR JRP Scan Select Rx Inst
User Manual: JRP_ScanSelect_Rx_InstHR
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
Operating Instructions JR ScanSelect Receivers Congratulations on the purchase of JR’s latest offering in receiver technology. General Operation The operation of your new JR® ScanSelect™ Receiver is designed to be easy and user-friendly, allowing for maximum convenience for the user, whether at the flying field or workbench. The ScanSelect receivers are designed to scan, detect and select the strongest operating signal when instructed to do so by the user. Tx Compatibility – The ScanSelect JR receivers are compatible with all JR transmitter types. Depending upon the receiver type (SPCM or FM), the transmission mode will need to be changed on the transmitter to match the receiver type. Changing Operating Channels: 1. Turn the power switch of the transmitter to “On” and have the transmitter located very close to the receiver and/or airplane with the receiver installed. 2. Apply power to the receiver. The receiver LED should glow. 3. Using a small instrument, depress the “Scan” button until the receiver LED turns off, then release the button. The LED will remain off for approximately 3 seconds. 4.While the LED is off, depress the “Scan” button once again. The receiver LED will flash for a short period while the receiver scans for the strongest frequency. When the receiver has locked onto its new frequency, the receiver LED will return to a solid glow, indicating the receiver is ready for operation. 5. Your receiver will remain locked onto this new assigned frequency until you, the user, initiate this change sequence again. 6. Be sure to perform a range check following the instructions provided with your radio system before flying on the new frequency choice. JR Product Warranty Important Note: Be sure to keep your original, dated sales receipt in a safe place as you will be required to provide proof-of-purchase date for the equipment to be serviced under warranty. Limited Warranty Period Horizon Hobby, Inc. guarantees this product to be free from defects in both material and workmanship for a period of 3 years from the date of purchase. Pursuant to this Limited Warranty, Horizon Hobby, Inc. will, at its option, (i) repair or (ii) replace, any product determined by Horizon Hobby, Inc. to be defective. In the event of a defect, these are your exclusive remedies. This warranty does not cover cosmetic damage or damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or modification of or to any part of the product. This warranty does not cover damage due to improper installation, operation, maintenance, or attempted repair by anyone other than an authorized Horizon Hobby, Inc. service center. This warranty is limited to the original purchaser and is not transferable. In no case shall Horizon Hobby’s liability exceed the original cost of the purchased product and will not cover consequential, incidental or collateral damage. Horizon Hobby, Inc. reserves the right to inspect any and all equipment involved in a warranty claim. Repair or replacement decisions are at the sole discretion of Horizon Hobby, Inc. Further, Horizon Hobby reserves the right to change or modify this warranty without notice. REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER. HORIZON HOBBY, INC. SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES. As Horizon Hobby, Inc. has no control over use, setup, final assembly, modification or misuse, no liability shall be assumed nor accepted for any resulting damage or injury. By the act of use, setup or assembly, the user accepts all resulting liability. If you as the purchaser or user are not prepared to accept the liability associated with the use of this product, you are advised to return this product immediately in new and unused condition to the place of purchase. Safety Precautions This is a sophisticated hobby product and not a toy. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this product in a safe and responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children without direct adult supervision. The product manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or injury. Questions, Assistance, and Repairs Your local hobby store and/or place of purchase cannot provide warranty support or repair. Once assembly, setup or use of the product has been started, you must contact Horizon Hobby, Inc. directly. This will enable Horizon to better answer your questions and service you in the event that you may need any assistance. For questions or assistance, please direct your email to productsupport@horizonhobby.com, or call 877.504.0233 toll free to speak to a service technician. Inspection or Repairs If your product needs to be inspected or repaired, please call for a Return Merchandise Authorization (RMA). Pack the product securely using a shipping carton. Please note that original boxes may be included, but are not designed to withstand the rigors of shipping without additional protection. Ship via a carrier that provides tracking and insurance for lost or damaged parcels, as Horizon Hobby, Inc. is not responsible for merchandise until it arrives and is accepted at our facility. Include your complete name, address, phone number where you can be reached during business days, RMA number, and a brief summary of the problem. Be sure your name, address, and RMA number are clearly written on the shipping carton. Warranty Inspection and Repairs To receive warranty service, you must include your original sales receipt verifying the proof-of-purchase date. Provided warranty conditions have been met, your product will be repaired or replaced free of charge. Repair or replacement decisions are at the sole discretion of Horizon Hobby. Non-Warranty Repairs Should your repair not be covered by warranty and the expense exceeds 50% of the retail purchase cost, you will be provided with an estimate advising you of your options. You will be billed for any return freight for non-warranty repairs. Please advise us of your preferred method of payment. Horizon Hobby accepts money orders and cashiers checks, as well as Visa, MasterCard, American Express, and Discover cards. If you choose to pay by credit card, please include your credit card number and expiration date. Any repair left unpaid or unclaimed after 90 days will be considered abandoned and will be disposed of accordingly. Electronics and engines requiring inspection or repair should be shipped to the following address (freight prepaid): Horizon Service Center 4105 Fieldstone Road Champaign, Illinois 61822 All other products requiring inspection or repair should be shipped to the following address (freight prepaid): Horizon Product Support 4105 Fieldstone Road Champaign, Illinois 61822 8236.3
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Tagged PDF : Yes XMP Toolkit : 3.1-702 About : e4524126-108d-11da-a9c1-cd583bbdb6bf Create Date : 2006:08:07 14:19:39-05:00 Metadata Date : 2006:08:16 09:51:26-05:00 Modify Date : 2006:08:16 09:51:26-05:00 Creator Tool : Adobe InDesign CS2 (4.0) Thumbnail Format : JPEG Thumbnail Width : 256 Thumbnail Height : 256 Thumbnail Image : (Binary data 8171 bytes, use -b option to extract) Instance ID : uuid:850a2471-c6e8-4cb8-9591-64e5a7129082 Document ID : adobe:docid:indd:4ae91cfa-2794-11db-b960-baf4eaeb685a Rendition Class : proof:pdf Derived From Instance ID : 4ae91cf9-2794-11db-b960-baf4eaeb685a Derived From Document ID : adobe:docid:indd:e4524124-108d-11da-a9c1-cd583bbdb6bf Format : application/pdf Producer : Adobe PDF Library 7.0 Trapped : False Page Count : 2 Creator : Adobe InDesign CS2 (4.0)EXIF Metadata provided by EXIF.tools