Panasonic KX TDE100 200 600 IP Networking Guide Pure PBX TDE200 TDE600 KXTDE 100

User Manual: Panasonic KX-TDE100 KX-TDE200 KX-TDE600 IP Networking Guide Panasonic KX-TDE100/200/600 - Telecomuserguides.com

Open the PDF directly: View PDF .
Page Count: 106

Download
Open PDF In Browser	View PDF

IP Networking Guide
Pure IP-PBX

KX-TDE100
KX-TDE200/KX-TDE600
Model No.

Thank you for purchasing a Panasonic Pure IP-PBX.
Please read this manual carefully before using this product and save this manual for future use.

KX-TDE100/KX-TDE200: PMMPR Software File Version 3.0000 or later
KX-TDE600: PGMPR Software File Version 3.0000 or later
Document Version: 2009-12

Table of Contents

Table of Contents
1 Introduction ..............................................................................................3
1.1
1.1.1
1.2
1.2.1
1.2.2
1.2.3
1.3
1.3.1
1.3.2

Overview ............................................................................................................................4
Establishing a VoIP Network with the Pure IP-PBX .........................................................4
Network Management .......................................................................................................7
DHCP (Dynamic Host Configuration Protocol) Server .....................................................7
VLAN (Virtual LAN) ..........................................................................................................8
Gatekeeper .....................................................................................................................10
Packet Control Features .................................................................................................11
Jitter Buffer .....................................................................................................................11
Voice Activity Detection (VAD) .......................................................................................11

2 Guidance for VoIP Installation ..............................................................12
2.1
2.1.1
2.1.2
2.1.3
2.1.4
2.2

VoIP Requirements .........................................................................................................13
Bandwidth Assessment ..................................................................................................13
Network Configuration ....................................................................................................16
Network Devices ............................................................................................................19
QoS (Quality of Service) .................................................................................................21
VoIP Requirements Checklist ........................................................................................22

3 Connection to the LAN ..........................................................................24
3.1
3.2

Connecting the IPCMPR/IPCEMPR/IP-EXT16 Card to the LAN ...................................25
Connecting the IP Telephones .......................................................................................28

4 Programming ..........................................................................................31
4.1
4.1.1
4.1.2
4.2
4.2.1
4.2.2
4.2.3
4.3
4.3.1
4.4
4.4.1
4.5
4.5.1
4.5.2
4.5.3
4.5.4
4.6
4.6.1
4.6.2

Programming the PBX ....................................................................................................32
Installing the Virtual IP Cards to the PBX .......................................................................32
Installing Additional Activation Keys ...............................................................................33
Programming the Virtual 16-Channel VoIP Gateway Card ..........................................36
Assigning the Hunt Pattern .............................................................................................36
Programming the Address Translation Table .................................................................37
Programming the Network Settings ................................................................................39
Programming the IPCMPR/IPCEMPR Card ...................................................................44
Assigning the IP Addressing Information .......................................................................44
Programming the IP-EXT16 Card ...................................................................................47
Assigning the IP Addressing Information .......................................................................47
Programming the IP Telephones ...................................................................................48
Assigning the IP Addressing Information .......................................................................48
Setting the VLAN Parameters ........................................................................................73
Setting the Diffserv Parameters .....................................................................................76
Configuration of IP Ports ................................................................................................79
Registering IP Telephones .............................................................................................86
Registering IP Telephones .............................................................................................86
De-registering IP Telephones .........................................................................................97

5 Appendix ...............................................................................................100
5.1
5.1.1
5.1.2
5.2

Revision History ............................................................................................................101
KX-TDE100/KX-TDE200 PMMPR Software File Version 3.0xxx .................................101
KX-TDE600 PGMPR Software File Version 3.0xxx .....................................................102
Error Message ...............................................................................................................103

IP Networking Guide

Document Version 2009-12

1 Introduction

Document Version 2009-12

IP Networking Guide

1.1.1 Establishing a VoIP Network with the Pure IP-PBX

1.1 Overview
1.1.1 Establishing a VoIP Network with the Pure IP-PBX
Panasonic Pure IP-PBX supports Panasonic KX-NT series IP proprietary telephones (IP-PTs), Panasonic IP
softphones, and SIP (Session Initiation Protocol) Extensions (hardphones and softphones) for communication
on a Voice over Internet Protocol (VoIP) network. These IP telephones can be used as extensions of the PBX
when the local office LAN is connected to other LANs at different locations.
The Pure IP-PBX also enables VoIP communication with PBXs installed at different locations. Since the
communication does not take place over conventional telephone network, the high cost of long distance
communication is virtually eliminated.
The following diagrams illustrate VoIP network with (i) a remote office LAN and (ii) another PBX installed at
different location.
Note

•
•

Panasonic IP Cell Station (IP-CS) units are also supported by the Pure IP-PBX for communication on
a VoIP network. For details, refer to the Quick Installation Guide for the IP-CS.
In this manual, the illustrations of the PBX are based on the KX-TDE200.

(i) VoIP Network with Remote Office LAN
Local Office LAN
SIP Extension
Extn. 102

Remote Office LAN

IP Softphone
Etxn. 103
IP-PT
Extn. 101

IP Softphone
Extn. 105

Switching
Hub

DHCP Server
SIP Extension
Extn. 106

PBX

IP-PT
Extn. 104

Router

Switching
Hub
DHCP Server

Router

IP Network

IP Networking Guide

Document Version 2009-12

1.1.1 Establishing a VoIP Network with the Pure IP-PBX

(ii) VoIP Network with Another PBX
Router

Headquarter

PBX
Switching Hub

IP Network

Router

PBX

Switching Hub

Branch

Document Version 2009-12

IP Networking Guide

1.1.1 Establishing a VoIP Network with the Pure IP-PBX

Network Parameters
You will need to have the following IP addressing and QoS information to establish VoIP communication on
your network. This information is typically supplied by a network administrator.
Consult your network administrator for specific values.
Parameter

Description

IP telephone IP Address

Identifies the location of IP telephones on the network. Each IP
telephone must have a unique IP address.

Subnet Mask Address

Defines which digits of an IP address are used for the network
address and the host address at each network location. The IP
addresses of the IP telephones and the PBX must fall within the same
subnet as that of the default gateway (e.g., router) of the LAN.

Default Gateway Address

Identifies the IP address of the primary gateway (typically a router or
similar device) that exchanges IP packets with the other gateways on
the VoIP network.

PBX IP Address

Identifies the location of the PBX in the network during VoIP
communications.

VLAN ID

Identifies the ID of the logical segment within the corporate LAN,
through which voice packets from IP telephones travel. For details,
refer to "1.2.2 VLAN (Virtual LAN)".

DiffServ (DS)

Identifies the value for the DS field in the header of IP packets, which
determines the priority given to packets traveling from IP telephones.
For details, refer to "4.5.3 Setting the Diffserv Parameters".

Types of IP Network
The speech quality depends on the type of IP network in use. Managed IP networks provide better speech
quality compared to unmanaged networks such as the Internet, where quality of service cannot be guaranteed.

Examples of recommended IP networks
• Digital Leased Line
• IP-VPN (Virtual Private Network)
• Frame Relay

Not recommended
• Internet (including an Internet VPN)

Note

•

Peer-to-peer calls between KX-NT300 series IP-PTs installed at different locations may not be possible
if packet communication cannot be established between the respective networks.
In this case, you need to configure the network settings (e.g., a VPN router when using an IP-VPN) to
establish packet communication.
Unlike an IP-VPN, which is set up over a network provider’s own IP network, an Internet VPN is set up
over the Internet. Internet VPNs are not recommended for VoIP communication because transmission
delays and loss of data are likely to occur.

IP Networking Guide

Document Version 2009-12

1.2.1 DHCP (Dynamic Host Configuration Protocol) Server

1.2 Network Management
1.2.1 DHCP (Dynamic Host Configuration Protocol) Server
To establish communication over a VoIP network, IP addresses must be assigned to IP telephones and the
PBX to identify their locations on the network. While these addresses can be assigned manually, it is also
possible to use a DHCP server to automatically assign IP address information. Using a DHCP server allows
you to centrally manage and automate the assignment of IP addresses.
When the IPCMPR (for KX-TDE100/
KX-TDE200)/IPCEMPR (for KX-TDE600)
and DSP cards are connected to
the network
1 Request IP address
information

IPCMPR/IPCEMPR
and DSP Cards

2 Assign IP address
information to the
IPCMPR/IPCEMPR
and DSP cards

When an IP telephone is
connected to the network

3 Request IP address
information

DHCP Server

4 Assign IP address
information to an IP
telephone

IP Telephone

Note

•
•
•

The IP address for the IP-EXT16 card cannot be assigned automatically using a DHCP server. This
IP address must be assigned manually using the Maintenance Console (PC programming software of
the PBX). For details, refer to "4.4 Programming the IP-EXT16 Card".
The PBX is not able to act as a DHCP server. To use the DHCP client function of IP telephones and
the IPCMPR/IPCEMPR/DSP cards, a separate DHCP server is required on the network, as shown
above.
An IP telephone and the IPCMPR/IPCEMPR/DSP cards cannot request IP addresses from a DHCP
server on another LAN (connected through an IP network). They can only receive IP addresses from
a DHCP server on the same LAN. Therefore, when IP telephones are located on several LANs, a DHCP
server is required on each LAN. If a DHCP server is not present on the LAN, IP addresses for IP
telephones and the IPCMPR/IPCEMPR/DSP cards on that LAN must be assigned manually.

Document Version 2009-12

IP Networking Guide

1.2.2 VLAN (Virtual LAN)

1.2.2 VLAN (Virtual LAN)
VLANs are logical segments within a corporate LAN. By assigning VLAN settings to IP telephones, it is possible
to separate the packets transmitted by an IP telephone according to the type of data and specify which VLAN
each data type will be sent over. This allows you to avoid generating unnecessary network traffic on each
segment and to reduce the load on the network. As a consequence, speech quality can be assured. Therefore,
we recommend using the VLAN feature to perform VoIP communication effectively.
Some IP telephones (e.g., KX-NT300 series) are equipped with 2 ports, primary and secondary, for packet
communication. Allocating these ports to different VLANs enables you to split the paths for packets depending
on whether the packet contains voice signals or data.
VLAN settings (VLAN ID and VLAN priority) for the primary port affect voice data transmitted by the IP
telephone, whereas VLAN settings for the secondary port apply to data transmitted by a PC connected to the
IP telephone. When sending packets, the IP telephone can attach information on which VLAN the packets are
to be transmitted over (VLAN Tagging). The switching hub that receives these packets reads the VLAN
information and sends the packets over the appropriate VLAN. This helps to ensure bandwidth for IP telephone
voice transmissions.
In this way, an IP telephone with 2 ports can transmit voice packets from the primary port with higher priority
than other packets from the secondary port.
VLAN 1

VLAN 2

Segment for Voice Data

Segment for Other Data

VLAN-capable Switching Hub

VLAN 1

VLAN 2

VLAN 1

PBX

VLAN 2

VLAN 1

Voice Packet

Other Packet

IP Telephone with 2 ports

Primary

Secondary

Note

•
•

This VLAN feature complies with IEEE (Institute of Electrical and Electronics Engineers) 802.1Q.
The PBX receives VLAN settings only from the connected switching hub. Therefore, VLAN settings for
the PBX must be assigned at the switching hub.

IP Networking Guide

Document Version 2009-12

1.2.2 VLAN (Virtual LAN)

•

Some PC LAN cards allow VLAN settings to be assigned. However, when using a PC connected to an
IP telephone with 2 ports, the VLAN settings for PC communications must be assigned only to the
secondary port of the IP telephone. Any VLAN settings assigned to the PC LAN card must be disabled.
These settings can usually be identified by "802.1Q", "802.1p", or "VLAN" in their name.
If you are using an IP telephone with a primary port only (e.g., KX-NT265), a PC cannot be connected
to the IP telephone.

Document Version 2009-12

IP Networking Guide

1.2.3 Gatekeeper

1.2.3 Gatekeeper
The following are the general functions of a gatekeeper:
• Dialed number-to-IP address translation
• Authentication
• Bandwidth control
The gatekeeper provides these network management functions to registered clients. To register with the
gatekeeper, you need to configure the V-IPGW16 card to use the gatekeeper and program the GK Settings
table through system programming. For details, refer to "3.9 [1-1] Slot—Shelf Property - Virtual IP Gateway
— Gatekeeper Available" and "3.10 [1-1] Slot—Shelf Property - Virtual IP Gateway—GK Settings" in the
PC Programming Manual. After programming, the V-IPGW16 card attempts to register with the gatekeeper
using registration information such as the IP address of the IPCMPR/IPCEMPR card, and destination telephone
numbers specified in the GK Settings table.
Note

•
•

For more information about gatekeeper functions, consult the documentation of the gatekeeper.
When using a gatekeeper, make sure to choose a compatible model. For more information about
gatekeeper compatibility with the V-IPGW16 card, consult a certified dealer.

IP Networking Guide

Document Version 2009-12

1.3.2 Voice Activity Detection (VAD)

1.3 Packet Control Features
1.3.1 Jitter Buffer
When voice signals are packetized and transmitted, individual packets can take different paths through the
network and arrive at the destination at varied timings. This is referred to as "jitter", and it can cause degradation
in speech quality. To compensate for jitter problems, the "jitter buffer" accumulates the packets temporarily for
processing.
To set the size of the jitter buffer, refer to "3.4 [1-1] Slot—Card Property - IPCMPR/IPCEMPR—VoIP-DSP
Option" in the PC Programming Manual.

1.3.2 Voice Activity Detection (VAD)
The VAD conserves bandwidth by detecting silent periods during a call and suppressing the packets of silence
from being sent to the network. This feature can be enabled or disabled for each available codec: G.711 and
G.729A.
To configure the VAD feature, refer to the appropriate section in the PC Programming Manual.
Note

•
•
•

To use the VAD feature for a certain codec, be sure to enable it for that codec on both the local and
remote gateway devices.
The VAD feature cannot be used between the V-IPGW16 and IP-GW4 cards since the V-IPGW16 card
does not support the G.723 codec (although calls can be made and received as normal).
The VAD feature between the V-IPGW16 and IP-GW16 cards can be enabled through system
programming. Refer to "Main— Connection for IP-GW16" under "3.11 [1-1] Slot—Shelf Property Virtual IP Gateway—GW Settings" in the PC Programming Manual.

Document Version 2009-12

IP Networking Guide

2 Guidance for VoIP Installation

IP Networking Guide

Document Version 2009-12

2.1.1 Bandwidth Assessment

2.1 VoIP Requirements
2.1.1 Bandwidth Assessment
When using the IP telephones and V-IPGW16 card, you must ensure that the IP network in use has enough
bandwidth to support VoIP communications. If the amount of bandwidth required for VoIP communications is
more than the network can accommodate, speech quality will be compromised. In addition, there may be an
adverse effect on the performance of other applications (e.g., email or web applications) that use the same
network. Therefore, care must be taken when assessing bandwidth requirements.
Inform your network administrator of the required bandwidth, and make sure that the network can support VoIP
communications even under conditions of maximum network traffic.

Bandwidth Assessment for IP Extension Card
Required Bandwidth per IP telephone for a Call
The required bandwidth depends on what combination of codecs and packet sending intervals is used. Keep
in mind the following points about the type of codecs and packet sending intervals, in terms of speech quality:
• The speech quality of the codecs varies as follows: (High) G.722, G.711, G.729A (Low)*1
• The shorter the packet sending interval, the higher the speech quality.
• The higher the speech quality the IP telephones provide, the more bandwidth the IP telephones require.
*1

When the preferred codec of each party differs, the call will be established using the lower codec. For example, if the caller prefers
G.711 while the called party prefers G.729A, the call will be established using G.729A.

Packet Sending Interval
Codec
20 ms

30 ms

40 ms

60 ms

G.722*1/G.711

87.2 kbps

79.5 kbps

—

G.729A

31.2 kbps

23.5 kbps

19.6 kbps

15.7 kbps

G.722 is only available for the KX-NT300 series IP-PTs and some SIP Extensions that support this codec during peer-to-peer
communication. For details, refer to "13.1.8 Peer-to-Peer Connection" in the Feature Manual.

Required Bandwidth for Each IP Extension Card
To allow all IP telephones to make calls simultaneously, it is necessary to keep available the bandwidth required
by an IP Extension card with the maximum number of IP telephones connected.
Provided below is the formula to calculate the amount of bandwidth required for each IP Extension card.
When using the IP-EXT16 card:
Required Bandwidth = (Required Bandwidth per IP telephone ´ 16)
When using the V-IPEXT32/V-SIPEXT32 card:
Required Bandwidth = (Required Bandwidth per IP telephone ´ 32)

Bandwidth Assessment for V-IPGW16 Card
Required Bandwidth for One VoIP Channel
The required bandwidth depends on what combination of codecs and packet sending intervals is used. Keep
in mind the following points about the type of codec and packet sending interval, in terms of the speech quality:
• The speech quality of the G.711 codec is higher than that of the G.729A codec.
• The shorter the packet sending interval, the higher the speech quality.
• The higher the speech quality the V-IPGW16 card provides, the more bandwidth the card requires.

Document Version 2009-12

IP Networking Guide

2.1.1 Bandwidth Assessment

Via LAN
Packet Sending Interval
Codec
20 ms

30 ms

40 ms

60 ms

90 ms

G.711

87.2 kbps

79.5 kbps

75.6 kbps

71.7 kbps

—

G.729A

31.2 kbps

23.5 kbps

19.6 kbps

15.7 kbps

—

Via WAN (PPP: Point-to-Point Protocol)
Packet Sending Interval
Codec
20 ms

30 ms

40 ms

60 ms

90 ms

G.711

84 kbps

77.3 kbps

74 kbps

70.7 kbps

—

G.729A

28 kbps

21 kbps

18 kbps

14.7 kbps

—

Bandwidth Calculation
Provided below is the formula to find out the amount of bandwidth required for VoIP communications:
Required Bandwidth
= (No. of Fax Machines ´ Required Bandwidth for the G.711 codec) +
[(16 - No. of Fax Machines) ´ Required Bandwidth for Voice Communication]

Example
Consider the following case as an example:
• Communication: via LAN
• No. of Fax Machines: 2
• G.711 Packet Sending Interval: 20 ms (requiring 87.2 kbps per channel)
• G.729A Packet Sending Interval for Voice Communication: 20 ms (requiring 31.2 kbps per channel)
In this case, the required bandwidth will be as follows:
Required Bandwidth
= (2 ´ 87.2) + [(16 - 2) ´ 31.2]
= 611.2 (kbps)
Therefore, inform your network administrator and make sure that the network can support a bandwidth of 611.2
kbps even when the network is under conditions of maximum traffic.
Note
It is recommended that all cards on a VoIP network have the same packet sending interval.

Additional Information
As described above, it is possible to control the required bandwidth by selecting a certain combination of codec
and packet sending interval. However, it is also possible to control required bandwidth by limiting the number
of available virtual VoIP channels.
The V-IPGW16 card supports a total of 8 ports, each having 2 separate channels. By disabling some of the
ports, you can reduce the bandwidth required for VoIP communications.

To limit the number of VoIP channels:
Set the status of the ports you wish to disable (starting from the highest-numbered port) to OUS.

IP Networking Guide

Document Version 2009-12

2.1.1 Bandwidth Assessment

For example, if you wish to use only 10 of the available 16 virtual VoIP channels (i.e., disable 6 channels), set
ports 8, 7, and 6 to OUS as shown below:

In this case, the equation for bandwidth calculation, based on the previous example, will change as follows:
Required Bandwidth
= (No. of Fax Machines ´ Required Bandwidth for the G.711 codec) +
[(10 - No. of Fax Machines) ´ Required Bandwidth for Voice Communication]
= (2 ´ 87.2) + [(10 - 2) ´ 31.2]
= 424 (kbps)

Document Version 2009-12

IP Networking Guide

2.1.2 Network Configuration

2.1.2 Network Configuration
You must evaluate the structure of the existing network to see if a VoIP network can be implemented. Below
are the points that should be evaluated.

Is the IP network a managed network?
A VoIP network should be implemented on a managed IP network such as Frame Relay, Leased Line, or
IP-VPN (Virtual Private Network).
An unmanaged network, such as the Internet (including an Internet VPN), cannot be used to employ a VoIP
network because delays and loss in data transmission can cause huge degradation in speech quality.

Is it possible to have static IP addressing?
IP telephones on the network always perform VoIP communications through the PBX. Therefore, the PBX
must be assigned static IP addresses, which must be programmed to each IP telephone on the network.
Note
When a DHCP server (which automates IP addressing of devices on the network) is not used, static IP
addressing must also be enabled for all IP telephones.

Does only a single router provide access to the IP network?
In a dual network, 2 routers provide access to the IP network as shown in the diagram below. However, only
one router can be used as an access point to the network.
Therefore, in the diagram below, if router A, whose IP address is assigned as the default gateway IP address
of the PBX and the IP telephones, fails, VoIP communications are no longer possible; they are not able to
switch their default gateway from router A to router B to access the IP network.
IP Network

Router A

Default gateway of
the PBX: Router A

IP Networking Guide

Router B

Default gateway of
the IP Telephone:
Router A

Document Version 2009-12

2.1.2 Network Configuration

Does the router not use network address translation (NAT/NAPT)?
If the router uses address translation techniques (e.g., NAT/NAPT) to convert between global and local IP
addresses, VoIP communications cannot be carried out effectively. Therefore, the routers used to access the
IP network must not use NAT/NAPT. Generally, NAT and NAPT are features that are available with routers.
Using NAT/NAPT

NOT Using NAT/NAPT

Local IP Address
Domain

Router

Global IP Address
Domain

IP Network

Local IP Address
Domain

Document Version 2009-12

Router

IP Network

Router

IP Networking Guide

2.1.2 Network Configuration

Is there only a single IP network between 2 ends of a call?
A huge degradation in speech quality will be produced when calls are made through multiple IP networks as
shown below; therefore, it is recommended that you avoid establishing a VoIP network in this fashion.

PSTN/
PRI QSIG, etc.

IP Network 1

IP Networking Guide

IP Network 2

Document Version 2009-12

2.1.3 Network Devices

Are the network devices located appropriately for effective VoIP
communications?
Transmission delays can cause pauses and loss in VoIP communications. The more network devices (e.g.,
routers and switching hubs) there are between the PBX and IP telephones or the IP network interface, the
longer the transmission delays. This is because a certain amount of delay is inevitable when packets go through
each network device.
To prevent unnecessary delays, it is recommended to connect the PBX as close to the IP telephones and the
IP network interface as possible so that the number of the network devices is kept to a minimum.
IP Network
Router

Router

Switching
Hub
Switching
Hub
Switching
Hub

2.1.3 Network Devices
You must evaluate the network devices that are used in the existing network to see if a VoIP network can be
implemented. Below are the points that should be evaluated.

Can the firewall pass packets appropriately?
If the VoIP network contains a firewall, the firewall must be configured appropriately to allow VoIP packets,
listed in the table below, to pass through the network without being blocked by filtering.
For more information, consult your network administrator.

[IP Packets from IPCMPR/IPCEMPR/IP-EXT16 Card and IP Telephones]
Protocol
RTP (IP telephone
connected to IPCMPR/
IPCEMPR)

Description
Real-time Transport Protocol.
Used for voice data transmission.

RTP (IP-PT connected to
IP-EXT16)
Maintenance (IPCMPR/
IPCEMPR)
Maintenance (IP-EXT16)
Maintenance (IP
telephone)

Document Version 2009-12

Panasonic proprietary protocol.
Used for communication parameter
negotiation with the PBX, download of
country/area data, confirmation of
connection with the PBX, and
notification of error messages and
statistical information to the PBX.

TCP/UDP

Default Port No.

UDP

12000 to 12255

UDP

8000 to 8063

TCP

35300

UDP

9300

UDP

9301

IP Networking Guide

2.1.3 Network Devices

Protocol
MGCP (IPCMPR/
IPCEMPR/IP-EXT16)

Description

TCP/UDP

Default Port No.

Media Gateway Control Protocol.
Used for call control command data and
LCD/LED data transmission.

UDP

2727

UDP

2427

Dynamic Host Configuration Protocol.
Used for receiving an IP address from a
DHCP server.

UDP

67, 68

UDP

67, 68

FTP (Port mode)

File Transfer Protocol.
Used for receiving a data file from a FTP
server to upgrade the firmware version.

TCP

20, 21

SNTP (IPCMPR/
IPCEMPR)

Simple Network Time Protocol.
Used for clock synchronization.

UDP

123

SNMP (IPCMPR/
IPCEMPR)

Simple Network Management Protocol.
Used for monitoring network-attached
devices.

UDP

161

MGCP (IP telephone)
DHCP (IPCMPR/
IPCEMPR)
DHCP (IP telephone)

[IP Packets from V-IPGW16 Card]
TCP/UDP

Protocol

Default Port No.

RTP/RTCP

UDP

12000 to 12255

H.245

TCP

10000 to 10447

H.225.0 Call Signaling

TCP

1720

H.225.0 RAS

UDP

1719

QSIG Connectionless Tunneling

TCP

1718

QSIG Connectionless Tunneling

UDP

1717

Are layer 2 or higher switches used?
Use of repeater hubs can increase the network load, and therefore may result in degradation in speech quality.
To ensure high speech quality, use only layer 2 or higher switches. Use of layer 2 or higher switches is also
strongly recommended for connecting IP telephones.
Note
Note that the port of the switching hub that connects to the IPCMPR/IPCEMPR/IP-EXT16 cards should be
set to operate under "Auto Negotiation" mode.

Are Category 5 (CAT 5) or higher cables used?
When connecting network devices, make sure to use CAT 5 or higher cables. If other types of cables are used,
communications may not be carried out normally.

IP Networking Guide

Document Version 2009-12

2.1.4 QoS (Quality of Service)

2.1.4 QoS (Quality of Service)
Some routers permit the configuration of priority control features. This allows the router to give higher priority
to voice packets and lower the rate of loss and delays during transmissions, hence improving speech quality.
It is strongly recommended that you use this feature, especially in networks where traffic is heavy.
Typically, a router identifies what packets to pass in priority by checking the value in the ToS field of the header
of IP packets. The V-IPGW16 card has the ability to set the ToS field of outgoing voice packets. When the card
is appropriately configured, the router can give voice packets from the card higher priority.
Consult your network administrator when setting the ToS field, as the setting value must conform to the
router’s specifications.
Note

•
•

Some switches also permit the configuration of priority control features. For more information, consult
your network administrator.
To adjust the value in the ToS field, refer to "3.9 [1-1] Slot—Shelf Property - Virtual IP Gateway" in the
PC Programming Manual.

Document Version 2009-12

IP Networking Guide

2.2 VoIP Requirements Checklist

2.2 VoIP Requirements Checklist
Use the following checklists to see if you can implement a VoIP network. The answers identified in underlined
bold-face letters are the required answers for the corresponding questions.

Bandwidth Assessment
No.

Question

Does the network have enough
bandwidth to support VoIP
communications?
Make sure that there is more bandwidth
available for VoIP communications than the
amount actually required.

Answer

Memo

•
Yes
No

•
•

IP network bandwidth
=
kbps
Available bandwidth for
VoIP
=
kbps
Required bandwidth for
VoIP
=
kbps

Ref.

p. 13

Network Configuration

No.

Question

2-a

Is the IP network a managed network?
Make sure to use a managed IP network such
as Frame Relay, Leased Line, or IP-VPN
(Virtual Private Network). The IPCMPR/
IPCEMPR/IP-EXT16 cards are not intended
for use on the Internet (including an Internet
VPN).

2-b

Is it possible to have static IP addressing?

2-c

Does only a single router provide access
to the IP network?

Yes

2-d

Does the router not use network address
translation (NAT/NAPT)?

Yes

2-e

Is there only a single IP network between
2 ends of a call?

Yes

2-f

Are the network devices located
appropriately for effective VoIP
communications?
It is recommended to connect the PBX as
close to IP telephones and the IP network
interface as possible.

IP Networking Guide

Answer

Memo

Ref.

Type of IP network:
Yes
No

Yes
No

p. 16

p. 17

p. 18

p. 19

Document Version 2009-12

2.2 VoIP Requirements Checklist

Network Devices
No.

Question

3-a

Can the firewall pass packets
appropriately?
When a firewall is used, make sure to
configure the firewall appropriately to allow
VoIP packets to pass through the network
without being blocked by filtering.

3-b

Are layer 2 or higher switches used?
Do not use repeater hubs as they can
increase the network load.
Also note that the port of the switching hub
that connects to the IPCMPR/IPCEMPR/
IP-EXT16 cards should be set to operate
under "Auto Negotiation" mode.

3-c

Are Category 5 (CAT 5) or higher cables
used?

Answer

Memo

Ref.

Model of firewall:
Yes

p. 19

Model of switch:
Yes

p. 20

Yes

p. 20

QoS (Quality of Service)
Question

No.

Answer

Memo

Ref.

Model of the router/switch:
4

Can the router or switch be configured to
use priority control features?

Document Version 2009-12

Yes
No

V-IPGW16 card’s ToS field
setting:

p. 21

IP Networking Guide

3 Connection to the LAN

This section describes the process of connecting
the IPCMPR/IPCEMPR/IP-EXT16 cards and IP
telephones to the LAN.

IP Networking Guide

Document Version 2009-12

3.1 Connecting the IPCMPR/IPCEMPR/IP-EXT16 Card to the LAN

3.1 Connecting the IPCMPR/IPCEMPR/IP-EXT16
Card to the LAN
Refer to the following example to connect the IPCMPR/IPCEMPR/IP-EXT16 card to the LAN.
When IPCMPR/IPCEMPR/IP-EXT16 cards are connected to the LAN for the first time, you must assign IP
addressing information to them. Refer to "4.3 Programming the IPCMPR/IPCEMPR Card"
or "4.4 Programming the IP-EXT16 Card" for instructions respectively.
Note

•
•
•
•

•

Use an Ethernet straight cable with an RJ45 connector to connect the card to a switching hub. The
cable should be a 10BASE-T/100BASE-TX CAT 5 (Category 5) or higher cable.
Before connecting the card, attach the included ferrite core to the cable.
Make sure to set the port of the switching hub that connects to the card to operate under "Auto
Negotiation" mode.
When using the VLAN feature on the network, make sure that the card is connected to a layer 2 switch
that is IEEE 802.1Q compliant, and that is configured for VLANs. In addition, the port of the switching
hub to which the card is connected must be set to "Untagged". Consult your network administrator for
details.
To use a KX-NT265, make sure that the Local Processor (LPR) software of the IP-EXT16 card is as
follows:
– PIPEXT Software Version 1.001 or later.
– PVOIPEX Software Version 1.011 or later.
To use a KX-NT300 series IP-PT, make sure that the LPR software of the IP-EXT16 card is as follows:
– PIPEXT Software Version 2.000 or later.
– PVOIPEX Software Version 2.000 or later.

Attaching a ferrite core to the cable
1. Wrap the cable once around the ferrite core, leaving a space between the ferrite core and the connector
as specified below.

2. Close the case of the ferrite core.

5 cm
(1-15/16 in)

3 cm
(1-3/16 in)

For IPCMPR/IPCEMPR Card

Document Version 2009-12

For IP-EXT16 Card

IP Networking Guide

3.1 Connecting the IPCMPR/IPCEMPR/IP-EXT16 Card to the LAN

Note
If you need to open the ferrite core, use a flathead screwdriver to unlatch the case.

Connecting the IPCMPR/IPCEMPR card to a switching hub

Router
LAN Port
Switching Hub
Switching Hub
Ethernet Straight Cable

IP Softphone

IP-PT
with 2 ports

SIP Extension
PC

IP Networking Guide

Document Version 2009-12

3.1 Connecting the IPCMPR/IPCEMPR/IP-EXT16 Card to the LAN

Connecting the IP-EXT16 card to a switching hub

RJ45
Router

Switching Hub
Switching Hub
Ethernet Straight Cable

IP-PT
with 2 ports
PC

IP-PT
with a primary port only

Document Version 2009-12

IP Networking Guide

3.2 Connecting the IP Telephones

3.2 Connecting the IP Telephones
When an IP telephone is connected to the LAN and power is supplied for the first time, you will be prompted
to set network parameters. The network parameters must be set for the IP telephone before it can be used.
Refer to "4.5 Programming the IP Telephones" for instructions.

Connecting an IP Telephone to a Switching Hub
When connecting an IP telephone to the LAN, connect it to a switching hub.
Note

•

Use an Ethernet straight cable with an RJ45 connector to connect the IP telephone to a switching hub.
The cable should be a 10BASE-T/100BASE-TX CAT 5 (Category 5) or higher cable.
• When using the VLAN feature on the network, make sure that the switching hub to be connected is
IEEE 802.1Q compliant and is configured for VLANs. In addition, the port of a switching hub that the
IP telephone is connected to must be set to "Trunk" port, to allow VLAN tagging. Consult your network
administrator for details.
• Since an IP softphone is installed and operates on a PC, the PC must be connected to the LAN to use
the IP softphone on the network.
The diagram below is for connecting an IP-PT to a switching hub. For SIP Extensions, refer to the
documentation of your SIP Extension.
Example: KX-NT346
To a Switching Hub
Ethernet Straight Cable

IP Networking Guide

Document Version 2009-12

3.2 Connecting the IP Telephones

Connecting an AC Adaptor to an IP Telephone
IP-PTs and some SIP Extensions comply with the IEEE 802.3af Power-over-Ethernet (PoE) standard. If PoE
is available on your network, these IP telephones can receive the necessary power supply from the network
through the network cable. In this case, no AC adaptor is needed for the IP telephones.
However, if PoE is not available, you will need to connect an AC adaptor to the IP telephone.
Note
Use only the specified type of AC adaptor for each IP telephone. For details, refer to the documentation of
your IP telephone.
Example: KX-NT346
To Wall Socket
AC Adaptor Cord

Document Version 2009-12

IP Networking Guide

3.2 Connecting the IP Telephones

Connecting a PC to an IP Telephone
You can connect a PC to some IP telephones (e.g., KX-NT300 series) using the IP telephone’s secondary
port. In this case, only a single port from the LAN’s network interface (switching hub) is required to connect
both the IP telephone and PC to the LAN.
Note

•
•
•
•
•

Use an Ethernet straight cable with an RJ45 connector to connect a PC to the IP telephone. The cable
should be a 10BASE-T/100BASE-TX CAT 5 (Category 5) or higher cable.
Only a PC can be connected to the secondary port of an IP telephone. Other IP telephones, including
IP-PTs, or network devices such as routers or switching hubs, cannot be connected.
The secondary port does not support PoE for connected devices.
In cases where a PC is connected to the secondary port, if the IP telephone connection to the PBX is
disconnected or reset, LAN communication to the PC will also be disrupted.
Generally, it is recommended that you connect no more than one PC to the secondary port of each IP
telephone.

Example: KX-NT346
To a PC
Ethernet Straight Cable

IP Networking Guide

Document Version 2009-12

4 Programming

Document Version 2009-12

IP Networking Guide

4.1.1 Installing the Virtual IP Cards to the PBX

4.1 Programming the PBX
4.1.1 Installing the Virtual IP Cards to the PBX
1.

a. Under Configuration, click Slot.
b. Move the mouse pointer over the white PBX image
at the bottom of the screen for the virtual slots.

c. Click Select Shelf.
2.

a. Click on the name of the desired card to install in the
list. An image of the card will be displayed.

b. Click and drag the image of the card to the Extension
or Trunk slot depending on the card type, and
release it. The card will move into the slot space.

IP Networking Guide

Click Yes to confirm.

Document Version 2009-12

4.1.2 Installing Additional Activation Keys

4.1.2 Installing Additional Activation Keys
If the preinstalled activation keys on the DSP16 or DSP64 cards are not enough for the desired configuration,
it is necessary to obtain additional activation keys in the form of activation key files and install them in the SD
Memory Card.

Activation Key Code and Key Management System
To obtain additional activation keys, you need to purchase the appropriate activation key codes and access
the Key Management System. You can download the activation keys as an activation key file from the Key
Management System. To download the activation keys, enter the MPR ID number shown on the IPCMPR/
IPCEMPR card in the PBX, and activation key number and registration ID provided on each activation key
code.
The following activation key codes are available to enable the use of IP CO lines, IP telephones, and
Communication Assistant (CA).
Note that the types of activation keys are subject to change without notice.
Model No.

Activation Key Type

Description

KX-NCS4102

2 IP Trunk

Provides the activation key number and registration ID
to download the activation key that enables the use of 2
IP CO lines.

KX-NCS4104

4 IP Trunk

Provides the activation key number and registration ID
to download the activation key that enables the use of 4
IP CO lines.

KX-NCS4201

1 IP Softphone/IP PT

Provides the activation key number and registration ID
to download the activation key that enables the use of 1
IP-PT/IP softphone.

KX-NCS4204

4 IP Softphone/IP PT

Provides the activation key number and registration ID
to download the activation key that enables the use of 4
IP-PTs/IP softphones.

KX-NCS4208

8 IP Softphone/IP PT

Provides the activation key number and registration ID
to download the activation key that enables the use of 8
IP-PTs/IP softphones.

KX-NCS4216

16 IP Softphone/IP PT

Provides the activation key number and registration ID
to download the activation key that enables the use of
16 IP-PTs/IP softphones.

KX-NCS4501

1 IP PT

Provides the activation key number and registration ID
to download the activation key that enables the use of 1
IP-PT.

KX-NCS4504

4 IP PT

Provides the activation key number and registration ID
to download the activation key that enables the use of 4
IP-PTs.

KX-NCS4508

8 IP PT

Provides the activation key number and registration ID
to download the activation key that enables the use of 8
IP-PTs.

KX-NCS4516

16 IP PT

Provides the activation key number and registration ID
to download the activation key that enables the use of
16 IP-PTs.

Document Version 2009-12

IP Networking Guide

4.1.2 Installing Additional Activation Keys

Model No.

Activation Key Type

Description

KX-NCS4701

1 SIP Extension

Provides the activation key number and registration ID
to download the activation key that enables the use of 1
SIP Extension.

KX-NCS4704

4 SIP Extension

Provides the activation key number and registration ID
to download the activation key that enables the use of 4
SIP Extensions.

KX-NCS4708

8 SIP Extension

Provides the activation key number and registration ID
to download the activation key that enables the use of 8
SIP Extensions.

KX-NCS4716

16 SIP Extension

Provides the activation key number and registration ID
to download the activation key that enables the use of
16 SIP Extensions.

KX-NCS2101

CA Basic 1user

Provides the activation key number and registration ID
to download the activation key that enables the use of
CA Basic for 1 user.

KX-NCS2105

CA Basic 5users

Provides the activation key number and registration ID
to download the activation key that enables the use of
CA Basic for 5 users.

KX-NCS2110

CA Basic 10users

Provides the activation key number and registration ID
to download the activation key that enables the use of
CA Basic for 10 users.

KX-NCS2140

CA Basic 40users

Provides the activation key number and registration ID
to download the activation key that enables the use of
CA Basic for 40 users.

KX-NCS2149

CA Basic 128users

Provides the activation key number and registration ID
to download the activation key that enables the use of
CA Basic for 128 users.

KX-NCS2201

CA Pro 1user

Provides the activation key number and registration ID
to download the activation key that enables the use of
CA PRO for 1 user.

KX-NCS2205

CA Pro 5users

Provides the activation key number and registration ID
to download the activation key that enables the use of
CA PRO for 5 users.

KX-NCS2210

CA Pro 10users

Provides the activation key number and registration ID
to download the activation key that enables the use of
CA PRO for 10 users.

KX-NCS2240

CA Pro 40users

Provides the activation key number and registration ID
to download the activation key that enables the use of
CA PRO for 40 users.

KX-NCS2249

CA Pro 128users

Provides the activation key number and registration ID
to download the activation key that enables the use of
CA PRO for 128 users.

KX-NCS2301

CA Supervisor 1user

Provides the activation key number and registration ID
to download the activation key that enables the use of
CA ACD Monitor for 1 ICD Supervisor.

IP Networking Guide

Document Version 2009-12

4.1.2 Installing Additional Activation Keys

Installing the Activation Key File in the SD Memory Card
1. Start the Maintenance Console from the Start menu.
2. From the Utility menu, select File Transfer PC to PBX (SD Card).
A dialog box will be displayed.

3. Select the file to upload.

4.
5.
6.
7.

A window showing the upload progress will be displayed.
While transferring files to the SD memory card, the PBX automatically renames them according to the
header information.
A message will be displayed when the transfer is complete.
Click OK.
Under Configuration, click Slot.
Click Activation Key.
For IP trunk activation key file(s), click Execute.
A confirmation message will be displayed. Click Yes.

Notice
The activation key file can only be installed in the PBX with the MPR ID number entered when the activation
key file was downloaded. The activation key file cannot be reissued unless the IPCMPR/IPCEMPR card
crashes.

Configuration of the Activation Keys
Depending on your configuration, it may be necessary to program the number of provided IP Trunk channels
to be used for H.323 CO lines. By default, all of the provided IP Trunk channels will be used for SIP CO lines.
Similarly, you can program how many IP softphones can be used through the IP Softphone/IP Proprietary
Telephone activation key. By default, only IP softphones can be used through the IP Softphone/IP Proprietary
Telephone activation key.
1.

a. Under Configuration, click Slot.
b. Click Activation Key.

a. In the The number of activated IP-GW box, type
the number of IP Trunk channels to be used for H.
323 CO lines.
b. In the The number of activated IP Softphone box,
type the number of IP softphones to be used through
the IP Softphone/IP Proprietary Telephone
activation key.

Click OK.
Note
A confirmation message will be displayed if you have
changed the number in the The number of
activated IP-GW box.
When the message is displayed, click Yes.

Note
For a detailed explanation about activation keys, refer to "2.1 Information about the Activation Keys" in
the Installation Manual.

Document Version 2009-12

IP Networking Guide

4.2.1 Assigning the Hunt Pattern

4.2 Programming the Virtual 16-Channel VoIP
Gateway Card
There are 2 methods to program the Virtual 16-Channel VoIP Gateway Card (V-IPGW16 card) to establish
VoIP communications between PBXs at different locations, as follows:
PBX code method

The caller dials the unique PBX code of the PBX to which the called party is
connected, in addition to the destination number.

Extension number
method

The caller dials only the destination number of the called party to call through
PBXs at different locations (hence there are fewer digits to dial than with the
PBX code method).

Note

•
•

For a detailed explanation about each method, refer to "13.1.15 PRIVATE NETWORK FEATURES"
in the Feature Manual.
Portions of this software are © 1996–2006 RADVISION Ltd. All intellectual property rights in such
portions of the Software and documentation are owned by RADVISION and are protected by United
States copyright laws, other applicable copyright laws and international treaty provisions. RADVISION
and its suppliers retain all rights not expressly granted.

4.2.1 Assigning the Hunt Pattern
The hunt pattern determines how to route incoming calls through virtual IP CO lines to the PBX. The procedure
below demonstrates the process of programming the hunt pattern of the local PBX. After the hunt pattern at
the local PBX has been fully assigned, repeat the procedure for the hunt pattern at the remote PBX with the
appropriate setting values.
1.

a. Under Configuration, click Slot.
b. Move the mouse pointer over the white PBX image
at the bottom of the screen for the virtual slots.

c. Click Select Shelf.
d. If the V-IPGW16 card’s status light is green, move
the mouse pointer over the card, select Ous from the
menu that appears, and then click Yes on the dialog
box. The status light will turn red.
e. Move the mouse pointer over the installed
V-IPGW16 card. A menu will be shown under the
mouse pointer.
f. Click Shelf Property.
g. Click Hunt Pattern.
2.

a. When using the PBX code method:
In the Leading Number box, type the local PBX
code and extension starting digit.
When using the extension number method:
In the Leading Number box, type the local
extension starting digit.
b. Click OK to return to the Shelf Property screen.

IP Networking Guide

Document Version 2009-12

4.2.2 Programming the Address Translation Table

Note
For more details about hunt pattern assignment, refer to "3.13 [1-1] Slot—Shelf Property - Virtual IP
Gateway—Hunt Pattern" in the PC Programming Manual.

4.2.2 Programming the Address Translation Table
The function of an address translation table in a VoIP network is to provide 2-way translation of telephone
numbers and IP addresses*1. Therefore, a caller can reach the destination by dialing the number without
knowing the destination IP address.
The procedure below demonstrates the process of programming the address translation table at the local PBX.
After the address translation table at the local PBX has been fully programmed, repeat the procedure for the
address translation table at the remote PBX with the appropriate setting values.
1.

a. Under Configuration, click Slot.
b. Move the mouse pointer over the white PBX image
at the bottom of the screen for the virtual slots.

In the Main tab, do the following to configure the
gateway entry for the remote PBX:
a. In the GW Name box, type a unique identifier of the
destination in the VoIP network.
b. In the GW IP Address box, type the IP address of
the destination gateway device.
c. In the GW Group box, select None.
Note
Having the value None for GW Group means
that the destination gateway device does not
belong to any gateway group. Grouping is useful
when installing multiple gateway devices at one
location. For details, refer to "3.11 [1-1] Slot—
Shelf Property - Virtual IP Gateway—GW
Settings— GW Group" in the PC
Programming Manual.

d. Click OK to return to the Shelf Property screen.
*1

IP address-to-telephone number translation can also be handled by using an H.323 Gatekeeper device. To configure Gatekeeper
devices, refer to the manufacturer’s documentation. This manual focuses on the method using the V-IPGW16 card’s internal address
translation capabilities.

Document Version 2009-12

IP Networking Guide

4.2.2 Programming the Address Translation Table

a. Click DN2IP.
b. When using the PBX code method:
In the Leading Number box, type the remote PBX
code and starting digit of destination extension.
When using the extension number method:
In the Leading Number box, type the remote PBX
code and starting digit of destination extension.
c. In the Remaining Number of Digits box, type a
number of digits to dial following the leading number.
d. In GW No./GW Group Selection, select GW No.
e. In the GW No. box, select 1 (the gateway entry for
the destination gateway device at the remote PBX).
f. Click OK.

Note
For more details about gateway settings, refer to "3.11 [1-1] Slot—Shelf Property - Virtual IP Gateway—
GW Settings" in the PC Programming Manual.

IP Networking Guide

Document Version 2009-12

4.2.3 Programming the Network Settings

4.2.3 Programming the Network Settings
For successful operation of a VoIP network using the V-IPGW16 card, network settings for the PBX at each
location must be programmed appropriately. For a detailed discussion of related features, refer to the Feature
Manual.
This section details the procedure to program the network settings for the local PBX. After the programming
for the local PBX has been done, repeat the procedure for the remote PBX with the appropriate setting values.
The following procedures describe the process of programming the network settings for each numbering
method.

Programming for the PBX Code Method
1.

a. Under Configuration, click Slot.
b. Move the mouse pointer over the white PBX image
at the bottom of the screen for the virtual slots.

c. Click Select Shelf.
d. Move the mouse pointer over the installed
V-IPGW16 card to display the menu of options.

e. Click Port Property.

Confirm that all ports are in service (INS).
Note
When a V-IPGW16 card is installed, 8 ports (1–8)
are available. When two V-IPGW16 cards are
installed, 16 ports (1–16) are available.

a. From the system menu, click CO & Incoming Call.
b. Click CO Line Settings.
c. Type the CO Name and assign an unused Trunk
Group Number to be used for all IP CO lines.
d. Click OK.

Document Version 2009-12

a.
b.
c.
d.
e.
f.

From the system menu, click System.
Click Numbering Plan.
Click Main.
Click the Features tab.
In the TIE Line Access box, type the dialing number.
Click OK.

IP Networking Guide

4.2.3 Programming the Network Settings

a. From the system menu, click Private Network.
b. Click TIE Table.
c. In the Own PBX Code box, type the PBX code of
the local PBX in the network.

d. In the first unused Leading Number box, type the
PBX code of the remote PBX in the network.

e. In the corresponding Trunk Group list, select the
number of the trunk group to be used when making
calls.
f. Set the number modification pattern, if necessary.
g. Click OK.
5.

a. From the system menu, click Configuration.
b. Click Slot.
c. Move the mouse pointer over the installed
V-IPGW16 card to display the menu of options.

d. Click Ous.
You will see a confirmation message.

e. Click Yes.
f. Move the mouse pointer over the installed
V-IPGW16 card to display the menu of options.

g. Click Shelf Property.

a. Click the Outgoing Call tab.
b. Select the preferred En-bloc Dialing setting
(Overlap (default) or En-bloc*1).
c. Click OK.

IP Networking Guide

Document Version 2009-12

4.2.3 Programming the Network Settings

a. Move the mouse pointer over the installed
V-IPGW16 card to display the menu of options.

b. Click INS.

When "En-bloc" is selected, you need to press "#" after dialing the phone number.

Programming for the Extension Number Method
1.

a. Under Configuration, click Slot.
b. Move the mouse pointer over the white PBX image
at the bottom of the screen for the virtual slots.

c. Click Select Shelf.
d. Move the mouse pointer over the installed
V-IPGW16 card to display the menu of options.

e. Click Port Property.

Confirm that all ports are in service (INS).
Note
When a V-IPGW16 card is installed, 8 ports (1–8)
are available. When two V-IPGW16 cards are
installed, 16 ports (1–16) are available.

a. From the system menu, click CO & Incoming Call.
b. Click CO Line Settings.
c. Type the CO Name and assign an unused Trunk
Group Number to be used for all IP CO lines.

d. Click OK.

Document Version 2009-12

IP Networking Guide

4.2.3 Programming the Network Settings

a.
b.
c.
d.
e.
f.

From the system menu, click System.
Click Numbering Plan.
Click Main.
Click the Other PBX Extension tab.
In the Other PBX Extension Numbering (TIE) box,
type a starting digit of destination extension.
Click OK.

a. From the system menu, click Private Network.
b. Click TIE Table.
c. In the Leading Number box, type the starting digit
of destination extension.

d. Click OK.

a. From the system menu, click Configuration.
b. Click Slot.
c. Move the mouse pointer over the installed
V-IPGW16 card to display the menu of options.

d. Click Ous.
You will see a confirmation message.
e. Click Yes.
f. Move the mouse pointer over the installed
V-IPGW16 card to display the menu of options.
g. Click Shelf Property.

a. Click the Outgoing Call tab.
b. Select the preferred En-bloc Dialing setting
(Overlap (default) or En-bloc*1).
c. Click OK.

IP Networking Guide

Document Version 2009-12

4.2.3 Programming the Network Settings

a. Move the mouse pointer over the installed
V-IPGW16 card to display the menu of options.

b. Click INS.

When "En-bloc" is selected, you need to press "#" after dialing the phone number.

Note
For details about network parameter settings, refer to the relevant sections of the PC Programming Manual.

Document Version 2009-12

IP Networking Guide

4.3.1 Assigning the IP Addressing Information

4.3 Programming the IPCMPR/IPCEMPR Card
4.3.1 Assigning the IP Addressing Information
The IP addressing information for the IPCMPR/IPCEMPR card can be assigned automatically through a DHCP
server or entered manually using the Maintenance Console.
Note

•
•
•

It is assumed that you have already installed the Maintenance Console on your PC.
The contents and design of the software are subject to change without notice.
Microsoft product screen shot(s) reprinted with permission from Microsoft Corporation.

Programming from Quick Setup
1.

Connect the PC to the PBX with an Ethernet straight cable or RS-232C cross cable.

Start the Maintenance Console from the Start menu.

"Information before programming" appears.
a. Carefully read this important additional information, which includes updates to this and other
manuals.
b. Click OK to close this window.

a. Enter the Installer Level Programmer Code (default: INSTALLER).
b. Click OK.

Click Connect.

a. Select your PBX model from PBX Model.
b. Select the LAN or RS-232C tab, depending on the type of PC connection with the PBX.
c. Specify the settings as required.
Note
When connecting to the PBX for the first time selecting LAN, the IP Address and Port
Number must be set to 192.168.0.101 and 35300 respectively.

d. Enter the system password for installer (default: 1234).
e. Click Connect.
7.

Quick Setup will launch automatically. On the IP addressing information screen, the information for the
IPCMPR/IPCEMPR card can be assigned automatically through a DHCP server or entered manually.
Note
If you change any information on this screen and click Apply, the PBX will need to be reset.
When using a DHCP server:
a. Select Enable for the DHCP Client setting.
b. Click Apply.
Note
The boxes will turn grey and the IP addresses will
be assigned automatically after the PBX is reset.

IP Networking Guide

Document Version 2009-12

4.3.1 Assigning the IP Addressing Information

When not using a DHCP server:
a. Select Disable for the DHCP Client setting.
b. For KX-TDE100/KX-TDE200, type the IP address
of the IPCMPR card in the IP Address for
IPCMPR Card box. For KX-TDE600, type the IP
address of the IPCEMPR card in the IP Address
for IPCEMPR Card box.*1
c. In the IP Address for VoIP-DSP box, type the IP
address of the DSP16 or DSP64 card.*2
d. In the Subnet Mask box, type the subnet mask
address of the network.*3
e. In the Default Gateway box, type the IP address
of the default gateway.*4
f. Click Apply.
8.

Follow the instructions of the Quick Setup wizard in Quick Setup.
After Quick Setup is completed, if the IP addressing information was not changed and a V-IPEXT card
was installed during setup, the IP-PT registration screen is displayed. For information on registering
IP-PTs to the PBX, refer to "Registration of IP-PTs" in "4.6.1 Registering IP Telephones".

Programming from the system menu
1.

The IP addressing information for the IPCMPR/
IPCEMPR card can also be assigned from the system
menu.
a. Under Configuration, click Slot.
b. Move the mouse pointer over the IPCMPR/
IPCEMPR card. A menu will be shown under the
mouse pointer.
c. Click Card Property.

When using a DHCP server:
a. Click the LAN Setting tab, then select Enable for
the DHCP Client setting.
b. Click Apply.

Document Version 2009-12

IP Networking Guide

4.3.1 Assigning the IP Addressing Information

When not using a DHCP server:
a. Click the LAN Setting tab, then select Disable for
the DHCP Client setting.
b. For KX-TDE100/KX-TDE200, type the IP address
of the IPCMPR card in the IP Address for
IPCMPR Card box. For KX-TDE600, type the IP
address of the IPCEMPR card in the IP Address
for IPCEMPR Card box.*1
c. In the IP Address for VoIP-DSP box, type the IP
address of the DSP16 or DSP64 card.*2
d. In the Subnet Mask box, type the subnet mask
address of the network.*3
e. In the Default Gateway box, type the IP address
of the default gateway.*4
f. Click Apply.

a. A screen will appear with information that any changes made in step 2 will be activated after the

PBX is restarted.

b. Click OK to restart the PBX.
Notice

•
•
•

*1
*2
*3
*4

Do not change the IP addresses of the IPCMPR/IPCEMPR and DSP cards once IP telephones are
registered to the PBX using these IP addresses.
The IP telephones will not operate properly if these IP addresses are changed.
A DHCP server must be able to use a "client identifier" option specified by RFC 2131.
The PBX will not start properly if the IP addresses cannot be assigned automatically by the DHCP
server when DHCP Client is set to Enable. In this case, you need to consult your network administrator
because the DHCP server on your network may not be running or a network failure may have occurred.
If the DHCP server is not available, change the DHCP Client setting to Disable and set fixed IP
addresses, then restart the PBX.
To change the DHCP Client setting, connect the PC with an RS-232C cross cable or Ethernet straight
cable. When connecting the PC with an Ethernet straight cable, make sure the PBX is disconnected
from the LAN and then connect the PC with an Ethernet straight cable using 192.168.0.101 for the IP
address of the IPCMPR/IPCEMPR card.

Valid IP address range: "1.0.0.0" to "223.255.255.255"
Valid IP address range: "1.0.0.0" to "223.255.255.255"
Valid subnet mask address range: "0–255.0–255.0–255.0–255" (except 0.0.0.0 and 255.255.255.255)
Valid IP address range: "1.0.0.0" to "223.255.255.255"

IP Networking Guide

Document Version 2009-12

4.4.1 Assigning the IP Addressing Information

4.4 Programming the IP-EXT16 Card
4.4.1 Assigning the IP Addressing Information
When an IP-EXT16 card is placed on the LAN for the first time, it is necessary to assign IP addressing
information to the card. This is done using the Maintenance Console.
1.

a. Under Configuration, click Slot.
b. Move the mouse pointer over the IP-EXT card. A
menu will be shown under the mouse pointer.

c. Click Ous to set the card to out-of-service status.
d. Move the mouse pointer over the IP-EXT card,
then click Card Property.

a. In the IP Address box, type the IP address of the
card.*1
b. In the Subnet Mask box, type the subnet mask
address of the network.*2
c. Click Apply.

If the IP address of the default gateway needs to be
entered:
a. Click Common Settings. A dialog box will
appear.
b. In the Gateway Address box, type the IP address
of the default gateway.*3
c. Click OK.
Note
To activate any changes made in step 3, it is
necessary to set all installed IP-EXT cards to
out-of-service status (OUS), then back to
in-service status (INS).

4.
*1
*2
*3

Move the mouse pointer over the IP-EXT card, then click INS to set the card to in-service status.
Valid IP address range: "1.0.0.0" to "223.255.255.255"
Valid subnet mask address range: "0–255.0–255.0–255.0–255" (except 0.0.0.0 and 255.255.255.255)
Valid IP address range: "1.0.0.0" to "223.255.255.255"

Document Version 2009-12

IP Networking Guide

4.5.1 Assigning the IP Addressing Information

4.5 Programming the IP Telephones
4.5.1 Assigning the IP Addressing Information
The IP address of an IP telephone, the subnet mask address, the default gateway address, and the PBX IP
address must be assigned to the IP telephone before it can be used on the network. These IP addressing
information can be assigned in the following ways:
Note
For details for the KX-NT400, refer to the Operating Instructions of the KX-NT400.

For IP-PTs connected to the IPCMPR/IPCEMPR Card
1. Using a DHCP server when the IP-PT is on the same LAN with the PBX
The DHCP server automatically assigns the IP address of the IP-PT, the subnet mask address, and the
default gateway address to the IP-PT.
The PBX IP address can also be assigned automatically to the IP-PT in process of being registered to the
PBX. For details about registering the IP-PT, refer to "4.6.1 Registering IP Telephones".
2. Using a DHCP server when the IP-PT is on the remote office LAN
While the DHCP server automatically assigns the IP address of the IP-PT, the subnet mask address, and
the default gateway address to the IP-PT, only the PBX IP address must be assigned manually.
Follow the procedure below to assign the PBX IP address.
If you need to set VLAN parameters, follow the procedure described in "4.5.2 Setting the VLAN
Parameters" after assigning the IP addresses without ending programming.

IP Networking Guide

Document Version 2009-12

4.5.1 Assigning the IP Addressing Information

KX-NT300 series (except KX-NT321)
To start programming
SETUP

Supply power to the IP-PT.

Press "SETUP"
when it is displayed.

To enter the IP address of the IPCMPR/IPCEMPR card (PBX IP Address)
Software version 2.00 or later only

Select "PBX".

ENTER

Select "PBX IP Address".

ENTER

Select "Primary PBX".

PBX IP Address
ENTER

ENTER

To enter the IP address of the Secondary PBX (optional for software version 2.00 or
later only)

PBX IP Address
Select "Secondary PBX".

ENTER

To set VLAN parameters

To the VLAN settings
OR

To end programming
STORE

The IP-PT will reboot
and can then be
registered to the PBX.

Press "STORE".

Document Version 2009-12

IP Networking Guide

4.5.1 Assigning the IP Addressing Information

KX-NT321
To start programming
Supply power to the IP-PT.
Press PROGRAM
while "Searching" is displayed.

To enter the IP address of the IPCMPR/IPCEMPR card in the Primary PBX (PBX IP Address)

Select "PBX".

Press SP-PHONE.

Select "PBX IP
Address".

Press SP-PHONE.

Select "Primary
PBX".

PBX IP Address
Press SP-PHONE.

Press SP-PHONE.

To enter the IP address of the Secondary PBX (if required)

PBX IP Address
Select "Secondary
PBX".

Press SP-PHONE.

Press HOLD twice to return
to the Menu screen.

To set VLAN parameters
To the VLAN settings
OR

To end programming
The IP-PT will reboot
and can then be
registered to the PBX.
Press STORE.

Note
To confirm the connection to the secondary PBX after programming, (1) turn the IP-PT’s power off,
and (2) hold the STORE button and 2 key while turning the power on.

IP Networking Guide

Document Version 2009-12

4.5.1 Assigning the IP Addressing Information

KX-NT265 (software version 2.00 or later only)
To start programming
Supply power to the IP-PT.
Press PROGRAM
while "Searching" is displayed.

To enter the IP address of the IPCMPR/IPCEMPR card (PBX IP Address)
HOLD

PBX IP
Address
Press VOLUME
to select "PBX".

Press SP-PHONE
twice.

Press SP-PHONE.

Press HOLD to return
to the Menu screen.

To set VLAN parameters
To the VLAN settings
OR

To end programming
The IP-PT will reboot
and can then be
registered to the PBX.
Press STORE.

Document Version 2009-12

IP Networking Guide

4.5.1 Assigning the IP Addressing Information

3. Not using a DHCP server when the IP-PT is on the same LAN with the PBX
Only the PBX IP address can be assigned automatically to the IP-PT in process of being registered to the
PBX. For details about registering the IP-PT, refer to "4.6.1 Registering IP Telephones".
Follow the procedure below to assign the IP address of the IP-PT, the subnet mask address, and the default
gateway address manually.
If you need to set VLAN parameters, follow the procedure described in "4.5.2 Setting the VLAN
Parameters" after assigning the IP addresses without ending programming.

KX-NT300 series (except KX-NT321)
To start programming
SETUP

Supply power to the IP-PT.

Press "SETUP" when it is displayed.

To set the IP address of the IP-PT

ENTER

Select "Network".

Select "Disable"
for DHCP setting.

ENTER

Select "IP Address".

IP Address*1
ENTER

To set the subnet mask address

Subnet Mask Address*2
Select "Subnet Mask".

ENTER

To set the default gateway address (if required)

Default Gateway Address*3
Select "Default Gateway".

ENTER

To enter the IP address of the Secondary PBX (optional for software version 2.00 or
later only)

Return to the
Menu screen.

Select "PBX".

ENTER

Select "PBX IP
Address".

ENTER

Select "Secondary
PBX".

PBX IP Address
ENTER

ENTER

Continued on next page

IP Networking Guide

Document Version 2009-12

4.5.1 Assigning the IP Addressing Information

Continued from previous page
To set VLAN parameters

To the VLAN settings
Return to the
Menu screen.
OR

To end programming
STORE

Return to the
Menu screen.
*1
*2
*3

The IP-PT will reboot
and can then be
registered to the PBX.

Press "STORE".

Valid IP address range: "1.0.0.0" to "223.255.255.255"
Valid subnet mask address range: "0–255.0–255.0–255.0–255" (except 0.0.0.0 and 255.255.255.255)"
Valid IP address range: "1.0.0.0" to "223.255.255.255"

Document Version 2009-12

IP Networking Guide

4.5.1 Assigning the IP Addressing Information

KX-NT321
To start programming

Supply power to the IP-PT.
Press PROGRAM
while "Searching" is displayed.

To set the IP address of the IP-PT

Select "Network".

Press SP-PHONE.

Select "DHCP (Disable)".

Press SP-PHONE
twice.

IP Address*1
Press SP-PHONE.

To set the subnet mask address

Subnet Mask Address*2
Select "Subnet Mask".

Press SP-PHONE.

To set the default gateway address (if required)

Default Gateway Address*3
Select "Default GW".

Press SP-PHONE.

To enter the IP address of the Secondary PBX (if required)

Press HOLD to return
to the Menu screen.

Select "PBX".

Press SP-PHONE.

Select "PBX IP
Address".

Press SP-PHONE.

Select "Secondary
PBX".

PBX IP Address
Press SP-PHONE.

Press SP-PHONE.

Press HOLD twice to return
to the Menu screen.

Continued on next page

IP Networking Guide

Document Version 2009-12

4.5.1 Assigning the IP Addressing Information

Continued from previous page

To set VLAN parameters
To the VLAN settings
OR

To end programming
The IP-PT will reboot
and can then be
registered to the PBX.
Press STORE.

*1
*2
*3

Valid IP address range: "1.0.0.0" to "223.255.255.255"
Valid subnet mask address range: "0–255.0–255.0–255.0–255" (except 0.0.0.0 and 255.255.255.255)
Valid IP address range: "1.0.0.0" to "223.255.255.255"

Note
To confirm the connection to the secondary PBX after programming, (1) turn the IP-PT’s power off,
and (2) hold the STORE button and 2 key while turning the power on.

Document Version 2009-12

IP Networking Guide

4.5.1 Assigning the IP Addressing Information

KX-NT265 (software version 2.00 or later only)
To start programming

Supply power to the IP-PT.
Press PROGRAM
while "Searching" is displayed.

To set the IP address of the IP-PT

Press VOLUME to
select "Network".

Press SP-PHONE.

Press VOLUME to
select "DHCP (Disable)".

Press SP-PHONE
twice.

IP Address*1
Press SP-PHONE.

To set the subnet mask address

Subnet Mask Address*2
Press VOLUME to
select "Subnet Mask".

Press SP-PHONE.

To set the default gateway address (if required)

Default Gateway Address*3
Press VOLUME to
select "Default GW".

Press SP-PHONE.

To set VLAN parameters
HOLD

To the VLAN settings

Press HOLD to return
to the Menu screen.

To end programming
The IP-PT will reboot
and can then be
registered to the PBX.

HOLD

Press HOLD to return
to the Menu screen.
*1
*2
*3

Press STORE.

IP Networking Guide

Document Version 2009-12

4.5.1 Assigning the IP Addressing Information

4. Not using a DHCP server when the IP-PT is on the remote office LAN
All the IP addressing information must be assigned manually.
Follow the procedure below to assign the IP addressing information.
If you need to set VLAN parameters, follow the procedure described in "4.5.2 Setting the VLAN
Parameters" after assigning the IP addresses without ending programming.

KX-NT300 series (except KX-NT321)
To start programming
SETUP

Supply power to the IP-PT.

Press "SETUP" when it is displayed.

To set the IP address of the IP-PT

ENTER

Select "Network".

Select "Disable"
for DHCP setting.

Select "IP Address".

ENTER

IP Address*1
ENTER

To set the subnet mask address

Subnet Mask Address*2
ENTER

Select "Subnet Mask".

ENTER

To set the default gateway address

Default Gateway Address*3
Select "Default Gateway".

ENTER

To enter the IP address of the IPCMPR/IPCEMPR card (PBX IP Address)
Software version 2.00 or later only

Return to the
Menu screen.

Select "PBX".

ENTER

Select "PBX IP
Address".

ENTER

Select "Primary
PBX".

PBX IP Address
ENTER

ENTER

Continued on next page

Document Version 2009-12

IP Networking Guide

4.5.1 Assigning the IP Addressing Information

Continued from previous page
To enter the IP address of the Secondary PBX (optional for software version 2.00 or
later only)

PBX IP Address
Select "Secondary PBX".

ENTER

To set VLAN parameters

To the VLAN settings
Return to the
Menu screen.
OR

To end programming
STORE

Return to the
Menu screen.

*1
*2
*3

The IP-PT will reboot
and can then be
registered to the PBX.

Press "STORE".

IP Networking Guide

Document Version 2009-12

4.5.1 Assigning the IP Addressing Information

KX-NT321
To start programming

Supply power to the IP-PT.
Press PROGRAM
while "Searching" is displayed.

To set the IP address of the IP-PT

Select "Network".

Press SP-PHONE.

Select "DHCP (Disable)".

Press SP-PHONE
twice.

IP Address*1
Press SP-PHONE.

To set the subnet mask address

Subnet Mask Address*2
Select "Subnet Mask".

Press SP-PHONE.

To set the default gateway address

Default Gateway Address*3
Select "Default GW".

Press SP-PHONE.

To enter the IP address of the IPCMPR/IPCEMPR card in the Primary PBX
(PBX IP Address)

Press HOLD to return
to the Menu screen.

Select "PBX".

Press SP-PHONE.

Select "PBX IP
Address".

Press SP-PHONE.

Select "Primary
PBX".

PBX IP Address
Press SP-PHONE.

Press SP-PHONE.

To enter the IP address of the Secondary PBX (if required)

PBX IP Address
Select "Secondary
PBX".

Press SP-PHONE.

Continued on next page

Document Version 2009-12

IP Networking Guide

4.5.1 Assigning the IP Addressing Information

Continued from previous page

Press HOLD twice to return
to the Menu screen.

To set VLAN parameters
To the VLAN settings
OR

To end programming
The IP-PT will reboot
and can then be
registered to the PBX.
Press STORE.

*1
*2
*3

Note
To confirm the connection to the secondary PBX after programming, (1) turn the IP-PT’s power off,
and (2) hold the STORE button and 2 key while turning the power on.

IP Networking Guide

Document Version 2009-12

4.5.1 Assigning the IP Addressing Information

KX-NT265 (software version 2.00 or later only)
To start programming

Supply power to the IP-PT.
Press PROGRAM
while "Searching" is displayed.

To set the IP address of the IP-PT

Press VOLUME to
select "Network".

Press SP-PHONE.

Press VOLUME to
select "DHCP (Disable)".

Press SP-PHONE
twice.

IP Address*1
Press SP-PHONE.

To set the subnet mask address

Subnet Mask Address*2
Press VOLUME to
select "Subnet Mask".

Press SP-PHONE.

To set the default gateway address

Default Gateway Address*3
Press VOLUME to
select "Default GW".

Press SP-PHONE.

To enter the IP address of the IPCMPR/IPCEMPR card (PBX IP Address)
HOLD

Press HOLD
twice to return
Press VOLUME
to the Menu screen. to select "PBX".

HOLD

PBX IP
Address
Press SP-PHONE
twice.

Press
SP-PHONE.

Press HOLD
to return to the
Menu screen.

To set VLAN parameters

To the VLAN settings
OR

To end programming
The IP-PT will reboot
and can then be
registered to the PBX.

Press STORE.
*1
*2
*3

Document Version 2009-12

IP Networking Guide

4.5.1 Assigning the IP Addressing Information

For IP-PTs connected to the IP-EXT16 Card
1. Using a DHCP server to automate the assignment of IP addressing information
The IP address of the IP-PT, the subnet mask address, and the default gateway address can be assigned
automatically by the DHCP server.
Only the IP address of the IP-EXT16 card (PBX IP address) must be assigned manually.
Follow the procedure below to assign the PBX IP address.
If you need to set VLAN parameters, follow the procedure described in "4.5.2 Setting the VLAN
Parameters" after assigning the IP addresses without ending programming.

KX-NT300 series (except KX-NT321)/KX-NT136
To start programming
SETUP

Supply power to the IP-PT.

Press "SETUP"
when it is displayed.

To enter the IP address of the IP-EXT16 card (PBX IP Address)
KX-NT300 with software version 2.00 or later only

Select "PBX".

ENTER

Select "PBX IP Address".

ENTER

Select "Primary PBX".

PBX IP Address
ENTER

ENTER

To enter the IP address of the Secondary PBX (optional for KX-NT300 with software
version 2.00 or later only)

PBX IP Address
Select "Secondary PBX".

ENTER

To set VLAN parameters

To the VLAN settings
OR

To end programming
STORE

The IP-PT will reboot
and can then be
registered to the PBX.

Press "STORE".

IP Networking Guide

Document Version 2009-12

4.5.1 Assigning the IP Addressing Information

KX-NT321
To start programming
Supply power to the IP-PT.
Press PROGRAM
while "Searching" is displayed.

To enter the IP address of the IP-EXT16 card in the Primary PBX (PBX IP Address)

Select "PBX".

Press SP-PHONE.

Select "PBX IP
Address".

Press SP-PHONE.

Select "Primary
PBX".

PBX IP Address
Press SP-PHONE.

Press SP-PHONE.

To enter the IP address of the Secondary PBX (If required)

PBX IP Address
Select "Secondary
PBX".

Press SP-PHONE.

Press HOLD twice to return
to the Menu screen.

To set VLAN parameters
To the VLAN settings
OR

To end programming
The IP-PT will reboot
and can then be
registered to the PBX.
Press STORE.

Note
To confirm the connection to the secondary PBX after programming, (1) turn the IP-PT’s power off,
and (2) hold the STORE button and 2 key while turning the power on.

Document Version 2009-12

IP Networking Guide

4.5.1 Assigning the IP Addressing Information

KX-NT265
To start programming
Supply power to the IP-PT.
Press PROGRAM
while "Searching" is displayed.

To enter the IP address of the IP-EXT16 card (PBX IP Address)
HOLD

PBX IP
Address
Press VOLUME
to select "PBX".

Press SP-PHONE
twice.

Press SP-PHONE.

Press HOLD to return
to the Menu screen.

To set VLAN parameters
To the VLAN settings
OR

To end programming
The IP-PT will reboot
and can then be
registered to the PBX.
Press STORE.

IP Networking Guide

Document Version 2009-12

4.5.1 Assigning the IP Addressing Information

2. Not using a DHCP server when assigning IP addressing information
All the IP addressing information must be assigned manually.
Follow the procedure below to assign the IP addressing information.
If you need to set VLAN parameters, follow the procedure described in "4.5.2 Setting the VLAN
Parameters" after assigning the IP addresses without ending programming.

KX-NT300 series (except KX-NT321)/KX-NT136
To start programming
SETUP

Supply power to the IP-PT.

Press "SETUP" when it is displayed.

To set the IP address of the IP-PT

ENTER

Select "Network".

Select "Disable"
for DHCP setting.

Select "IP Address".

ENTER

IP Address*1
ENTER

To set the subnet mask address

Subnet Mask Address*2
ENTER

Select "Subnet Mask".

ENTER

To set the default gateway address (if required)

Default Gateway Address*3
Select "Default Gateway".

ENTER

To enter the IP address of the IP-EXT16 card (PBX IP Address)
KX-NT300 with software version 2.00 or later only

Return to the
Menu screen.

Select "PBX".

ENTER

Select "PBX IP
Address".

ENTER

Select "Primary
PBX".

PBX IP Address
ENTER

ENTER

Continued on next page

Document Version 2009-12

IP Networking Guide

4.5.1 Assigning the IP Addressing Information

Continued from previous page
To enter the IP address of the Secondary PBX (optional for KX-NT300 with software
version 2.00 or later only)

PBX IP Address
Select "Secondary PBX".

ENTER

To set VLAN parameters

To the VLAN settings
Return to the
Menu screen.
OR

To end programming
STORE

Return to the
Menu screen.

*1
*2
*3

The IP-PT will reboot
and can then be
registered to the PBX.

Press "STORE".

IP Networking Guide

Document Version 2009-12

4.5.1 Assigning the IP Addressing Information

KX-NT321
To start programming

Supply power to the IP-PT.
Press PROGRAM
while "Searching" is displayed.

To set the IP address of the IP-PT

Select "Network".

Press SP-PHONE.

Select "DHCP (Disable)".

Press SP-PHONE
twice.

IP Address*1
Press SP-PHONE.

To set the subnet mask address

Subnet Mask Address*2
Select "Subnet Mask".

Press SP-PHONE.

To set the default gateway address (if required)

Default Gateway Address*3
Select "Default GW".

Press SP-PHONE.

To enter the IP address of the IP-EXT16 card in the Primary PBX (PBX IP Address)

Press HOLD to return
to the Menu screen.

Select "PBX".

Press SP-PHONE.

Select "PBX IP
Address".

Press SP-PHONE.

Select "Primary
PBX".

PBX IP Address
Press SP-PHONE.

Press SP-PHONE.

To enter the IP address of the Secondary PBX (If required)

PBX IP Address
Select "Secondary
PBX".

Press SP-PHONE.

Continued on next page

Document Version 2009-12

IP Networking Guide

4.5.1 Assigning the IP Addressing Information

Continued from previous page

Press HOLD twice to return
to the Menu screen.

To set VLAN parameters
To the VLAN settings
OR

To end programming
The IP-PT will reboot
and can then be
registered to the PBX.
Press STORE.

*1
*2
*3

Note
To confirm the connection to the secondary PBX after programming, (1) turn the IP-PT’s power off,
and (2) hold the STORE button and 2 key while turning the power on.

IP Networking Guide

Document Version 2009-12

4.5.1 Assigning the IP Addressing Information

KX-NT265
To start programming

Supply power to the IP-PT.
Press PROGRAM
while "Searching" is displayed.

To set the IP address of the IP-PT

Press VOLUME to
select "Network".

Press SP-PHONE.

Press VOLUME to
select "DHCP (Disable)".

Press SP-PHONE
twice.

IP Address*1
Press SP-PHONE.

To set the subnet mask address

Subnet Mask Address*2
Press VOLUME to
select "Subnet Mask".

Press SP-PHONE.

To set the default gateway address (if required)

Default Gateway Address*3
Press VOLUME to
select "Default GW".

Press SP-PHONE.

To enter the IP address of the IP-EXT16 card (PBX IP Address)
HOLD

Press HOLD
twice to return
Press VOLUME
to the Menu screen. to select "PBX".

HOLD

PBX IP
Address
Press SP-PHONE
twice.

Press
SP-PHONE.

Press HOLD
to return to the
Menu screen.

To set VLAN parameters

To the VLAN settings
OR

To end programming
The IP-PT will reboot
and can then be
registered to the PBX.

Press STORE.
*1
*2
*3

Document Version 2009-12

IP Networking Guide

4.5.1 Assigning the IP Addressing Information

For KX-HGT100 SIP Telephones
1. Using a DHCP server to automate the assignment of IP addressing information
The DHCP server automatically assigns the IP address of the KX-HGT100, the subnet mask address, and
the default gateway address to the KX-HGT100.
The PBX IP address can be assigned to the KX-HGT100 through Web Programming. For details, refer
to "4.6.1 Registering IP Telephones".
Follow the procedure below to assign IP addressing information automatically.

To start programming

Supply power to the KX-HGT100.
Press PROGRAM.

To set the IP address of the KX-HGT100

C. Tone
Select "Set network".

Press OK.

Select "DHCP".

Press OK.

To end programming

Press PROGRAM.

2. Not using a DHCP server when assigning IP addressing information
The IP address of the KX-HGT100, the subnet mask address, and the default gateway address must be
assigned manually.
The PBX IP address can be assigned to the KX-HGT100 through Web Programming. For details, refer
to "4.6.1 Registering IP Telephones".

IP Networking Guide

Document Version 2009-12

4.5.1 Assigning the IP Addressing Information

Follow the procedure below to assign IP addressing information manually.

To start programming

Supply power to the KX-HGT100.
Press PROGRAM.

To set the IP addressing information

Select "Set network".

Press OK.

Select "STATIC".

Press OK.

Subnet Mask Address*2

IP Address*1
Press OK.

Press OK.

Default Gateway Address*3
Press OK.

C. Tone

To end programming

Press PROGRAM.
*1
*2
*3

Document Version 2009-12

IP Networking Guide

4.5.1 Assigning the IP Addressing Information

For SIP Extensions (except KX-HGT100)
1. Using a DHCP server to automate the assignment of IP addressing information
The IP address of the SIP Extension, the subnet mask address, and the default gateway address can be
assigned to the SIP Extension automatically by the DHCP server.
The IP address of the IPCMPR/IPCEMPR card (PBX IP address) must be assigned manually on the SIP
Extension side.
For instructions, refer to the documentation of the SIP Extension.
2. Not using a DHCP server when assigning IP addressing information
All the IP addressing information must be assigned manually.
For instructions, refer to the documentation of the SIP Extension.
Note

•
•

SIP Extensions can only receive IP addressing information from a DHCP server on its own LAN.
Therefore, when SIP Extensions are located on several LANs, a DHCP server is required on each LAN.
When the DHCP client function is enabled for SIP Extensions, simply connect the SIP Extensions to
the LAN to use the DHCP server. For the DHCP client function setting, refer to the documentation of
the SIP Extension.

IP Networking Guide

Document Version 2009-12

4.5.2 Setting the VLAN Parameters

4.5.2 Setting the VLAN Parameters
To establish voice communications between IP telephones, the primary ports of the IP telephones and the
connected PBX must belong to the same VLAN. Consult your network administrator and obtain the appropriate
VLAN ID.
If you are using an IP telephone equipped with two ports, it is possible to place primary and secondary ports
of the IP telephone on different VLANs by assigning separate VLAN IDs to each port.
Follow the procedure below for all IP-PTs on the network, using appropriate VLAN IDs.
Note

•
•

For details for the KX-NT400, refer to the Operating Instructions of the KX-NT400.
The procedure for SIP Extensions may vary depending on the type of the SIP Extension being used.
Refer to the documentation of your SIP Extension for instructions.

KX-NT300 series (except KX-NT321)/KX-NT136
KX-NT300 series only

After assigning
the IP addresses

Select "QoS".

ENTER

Select "VLAN".

Select "Enable" for
VLAN setting.

To set the VLAN ID for the primary port

VLAN ID
ENTER

Select "Primary port".

Select "VLAN ID".

ENTER

1–4094

VLAN Priority*1
ENTER

Select "VLAN Priority".

ENTER

0–7

To set the VLAN ID for the secondary port

Return to the
VLAN setting screen.

Select
"Secondary port (TO PC)".

ENTER

*1
1
VLAN Priority

VLAN ID
1–4094

ENTER

Select "VLAN ID".

ENTER

Select
"VLAN Priority".

ENTER

0–7

ENTER

To end programming
STORE

Return to the
Menu screen.

The IP-PT will reboot
and can then be
registered to the PBX.

Press "STORE".

The VLAN priority of the primary port must be set higher than the priority of the secondary port. The larger the number, the higher
the priority.

Document Version 2009-12

IP Networking Guide

4.5.2 Setting the VLAN Parameters

KX-NT321

After assigning
the IP addresses
Select "QoS".

Select "VLAN (Enable)".

Press SP-PHONE.

Select "VLAN".

Press SP-PHONE.

To set the VLAN ID for the primary port

VLAN ID
Select "VLAN (Primary)".

Press SP-PHONE.

Select "VLAN ID".

1–4094

Press SP-PHONE.

VLAN Priority*1
Select "Priority".

0–7

Press SP-PHONE.

To set the VLAN ID for the secondary port

VLAN ID
Select "VLAN (Secondary)".

Press SP-PHONE.

Select "VLAN ID".

1–4094

Press SP-PHONE.

VLAN Priority*1
Select "Priority".

0–7

Press SP-PHONE.

To end programming
The IP-PT will reboot
and can then be
registered to the PBX.

Press HOLD three
times to return to the
Menu screen.

Press STORE.

The VLAN priority of the primary port must be set higher than the priority of the secondary port. The larger the number, the higher
the priority.

IP Networking Guide

Document Version 2009-12

4.5.2 Setting the VLAN Parameters

KX-NT265

After assigning
the IP addresses
Press VOLUME to Press SP-PHONE. Press VOLUME to
select "QoS".
select "VLAN".

1–4094

Press VOLUME to
select "VLAN (Enable)".

VLAN Priority

VLAN ID
Press SP-PHONE.

Press SP-PHONE.

0–7

Press SP-PHONE.

To end programming
The IP-PT will reboot
and can then be
registered to the PBX.

HOLD

Press HOLD to return
to the Menu screen.

Document Version 2009-12

Press STORE.

IP Networking Guide

4.5.3 Setting the Diffserv Parameters

4.5.3 Setting the Diffserv Parameters
Differentiated Services (DiffServ, or DS) is an IP-based QoS technique used to control QoS of VoIP
communications by setting the DS field in the header of IP packets. Consult your network administrator for the
appropriate setting values for the DS field.
Follow the procedure below to set the Diffserv parameters. Only KX-NT300 series IP-PTs and KX-NT265
IP-PTs (software version 2.00 or later) can be used to set the parameters.
Note
For details for the KX-NT400, refer to the Operating Instructions of the KX-NT400.

KX-NT300 series (except KX-NT321)
To start programming
SETUP

Press "SETUP"
when it is displayed.

Select "Qos".

ENTER

Select "Diffserv".

To set the DS field value for the primary port

Select "Primary Port".

ENTER

Select "Enable".

ENTER

Diffserv
0.0–7.7

ENTER

To set the DS field value for the secondary port

Return to the
Diffserv setting screen.

Select
"Secondary Port (TO PC)".

ENTER

Select "Enable".

Diffserv
ENTER

0.0–7.7

ENTER

To end programming
STORE

Return to the
Menu screen.

IP Networking Guide

The IP-PT will reboot
and can then be
registered to the PBX.

Press "STORE".

Document Version 2009-12

4.5.3 Setting the Diffserv Parameters

KX-NT321
To start programming

Press PROGRAM while
"Searching" is displayed.

Select "QoS".

Press SP-PHONE.

Select "Diffserv".

Press SP-PHONE.

To set the DS field value for the primary port

Select "Primary Port".

Press SP-PHONE.

Select "DS (Enable)".

Press SP-PHONE.

Diffserv
0.0–7.7

Press SP-PHONE.

To set the DS field value for the secondary port

Press HOLD to return to
the Diffserv setting screen.

Select "Secondary Port".

Press SP-PHONE.

Select "DS (Enable)".

Diffserv
Press SP-PHONE.

0.0–7.7

Press SP-PHONE.

To end programming
The IP-PT will reboot
and can then be
registered to the PBX.
Press HOLD to return
to the Menu screen.

Document Version 2009-12

Press STORE.

IP Networking Guide

4.5.3 Setting the Diffserv Parameters

KX-NT265 (software version 2.00 or later only)
To start programming

Press PROGRAM while
"Searching" is displayed.

Press VOLUME to
select "QoS".

Press SP-PHONE.

Press VOLUME to
select "Diffserv".

Press SP-PHONE.

To set the DS field value

Diffserv
Press VOLUME to
select "DS (Enable)".

Press SP-PHONE.

0.0–7.7

Press SP-PHONE.

To end programming
HOLD

Press HOLD to return
to the Menu screen.

IP Networking Guide

The IP-PT will reboot
and can then be
registered to the PBX.

Press STORE.

Document Version 2009-12

4.5.4 Configuration of IP Ports

4.5.4 Configuration of IP Ports
A KX-NT300 series IP-PT user or KX-NT265 IP-PT (software version 2.00 or later) user can configure the port
number of PTAP, DHCP, and FTP ports. Consult your network administrator to check whether the configuration
of the IP ports is required.
Follow the procedure below to configure the port number of the IP ports.
Note
For details for the KX-NT400, refer to the Operating Instructions of the KX-NT400.

Document Version 2009-12

IP Networking Guide

4.5.4 Configuration of IP Ports

KX-NT300 series (except KX-NT321)
To start programming
SETUP

Press "SETUP"
when it is displayed.

Password
Select "IP Port".

ENTER

7678

ENTER

To configure the port number of PTAP Ports
Software version 2.00 or later only

Select "PTAP Server Port".

ENTER

Select "Primary PBX".

ENTER

Port No.
1024–65535

ENTER

To configure the port number of PTAP Ports for the Secondary PBX (optional for
software version 2.00 or later only)

Select "PTAP Server Port".

ENTER

Select "Secondary PBX".

ENTER

Port No.
1024–65535

ENTER

Port No.
Select "PTAP Client Port".

ENTER

1024–65535

ENTER

To configure the port number of DHCP Ports

Port No.
Select "DHCP Server Port".

ENTER

67, 1024–65535

ENTER

Port No.
Select "DHCP Client Port".

ENTER

68, 1024–65535

ENTER

Continued on next page

IP Networking Guide

Document Version 2009-12

4.5.4 Configuration of IP Ports

Continued from previous page
To configure the port number of FTP Ports

Port No.
Select "FTP Server Ctrl Port".

ENTER

21, 1024–65535

ENTER

Port No.
Select "FTP Client Ctrl Port".

ENTER

1024–65535

ENTER

Port No.
Select "FTP Client Data Port".

ENTER

1024–65535

ENTER

To end programming
STORE

Return to the
Menu screen.

Document Version 2009-12

The IP-PT will reboot
and can then be
registered to the PBX.

Press "STORE".

IP Networking Guide

4.5.4 Configuration of IP Ports

KX-NT321
To start programming

Password
Press PROGRAM while
"Searching" is displayed.

Select "IP Port".

Press SP-PHONE.

7678

Press SP-PHONE.

To configure the port number of PTAP Ports

Select "PTAP Server".

Press SP-PHONE.

Select "Primary PBX".

Press SP-PHONE.

Press HOLD.

Press SP-PHONE.

Port No.
1024–65535

To configure the port number of PTAP Ports for the Secondary PBX (if required)

Select "PTAP Server".

Press SP-PHONE.

Select "Secondary PBX".

Press SP-PHONE.

Press HOLD.

Press SP-PHONE.

Port No.
1024–65535

Port No.
Select "PTAP Client".

Press SP-PHONE.

1024–65535

Press SP-PHONE.

To configure the port number of DHCP Ports

Port No.
Select "DHCP Server".

Press SP-PHONE.

67, 1024–65535

Press SP-PHONE.

Port No.
Select "DHCP Client".

Press SP-PHONE.

68, 1024–65535

Press SP-PHONE.

Continued on next page

IP Networking Guide

Document Version 2009-12

4.5.4 Configuration of IP Ports

Continued from previous page
To configure the port number of FTP Ports

Port No.
Select "FTP Server Ctrl".

Press SP-PHONE.

21, 1024–65535

Press SP-PHONE.

Port No.
Select "FTP Client Ctrl".

Press SP-PHONE.

1024–65535

Press SP-PHONE.

Port No.
Select "FTP Client Data".

Press SP-PHONE.

1024–65535

Press SP-PHONE.

To end programming
The IP-PT will reboot
and can then be
registered to the PBX.
Press HOLD to return
to the Menu screen.

Document Version 2009-12

Press STORE.

IP Networking Guide

4.5.4 Configuration of IP Ports

KX-NT265 (software version 2.00 or later only)
To start programming

Password
Press PROGRAM while
"Searching" is displayed.

Press VOLUME to
select "IP Port".

Press SP-PHONE.

7678

Press SP-PHONE.

To configure the port number of PTAP Ports

Port No.
Press VOLUME to
select "PTAP Server".

Press SP-PHONE.

1024–65535

Press SP-PHONE.

Port No.
Press VOLUME to
select "PTAP Client".

Press SP-PHONE.

1024–65535

Press SP-PHONE.

To configure the port number of DHCP Ports

Port No.
Press VOLUME to
select "DHCP Server".

Press SP-PHONE.

67, 1024–65535

Press SP-PHONE.

Port No.
Press VOLUME to
select "DHCP Client".

Press SP-PHONE.

68, 1024–65535

Press SP-PHONE.

To configure the port number of FTP Ports

Port No.
Press VOLUME to
select "FTP Server Ctrl".

Press SP-PHONE.

21, 1024–65535

Press SP-PHONE.

Port No.
Press VOLUME to
select "FTP Client Ctrl".

Press SP-PHONE.

1024–65535

Press SP-PHONE.

Port No.
Press VOLUME to
select "FTP Client Data".

Press SP-PHONE.

1024–65535

Press SP-PHONE.

To end programming
HOLD

Press HOLD to return
to the Menu screen.

IP Networking Guide

The IP-PT will reboot
and can then be
registered to the PBX.

Press STORE.

Document Version 2009-12

4.5.4 Configuration of IP Ports

Note
If you wish to change the port number back to default, enter 0 as the port number for the desired port.

Document Version 2009-12

IP Networking Guide

4.6.1 Registering IP Telephones

4.6 Registering IP Telephones
4.6.1 Registering IP Telephones
After the programming of the PBX and IP telephone is finished, the IP telephone must be registered to the
PBX. This is done using the Maintenance Console.

Registration of IP-PTs
1.

a. Under Configuration, click Slot.
b. When registering with V-IPEXT32 Card:
Move the mouse pointer over the white PBX
image at the bottom of the screen for the virtual
slots, and click Select Shelf. Move the mouse
pointer over the V-IPEXT32 card. A menu will be
shown under the mouse pointer.
When registering with IP-EXT Card:
Move the mouse pointer over the IP-EXT card. A
menu will be shown under the mouse pointer.
c. Click Port Property.

To register the IP-PT by entering the MAC address directly:
2.

Enter the MAC address of the IP-PT in the IP Phone
Registration ID (MAC Address) box.

Click Apply.
Once the IP-PT is successfully registered, the status
of the IP-PT will update to show "Registered".

To register the IP-PT using the wizard:
2.

Click Registration.
A dialog box will appear. Non-registered (available)
extension numbers and names are displayed on the
left.

IP Networking Guide

Document Version 2009-12

4.6.1 Registering IP Telephones

a. Highlight numbers and names and click the right
arrow to select them for registration.

b. Click Next. A screen will appear with information
on the current IP-PT extension number and name,
and index number for programming.
Note

•

If the IP-PT has been connected to the
LAN and power has been turned on, the
IP address of the IPCMPR/IPCEMPR
card will be assigned automatically.
If not, connect the IP-PT to the LAN and
turn the power on within 15 minutes after
this operation is done. The IP address of
the IPCMPR/IPCEMPR card will then be
assigned automatically.

c. If the registration is still in progress, the dialog box
will show "Registration Executing".
If the registration is successful, the dialog box will
show "Registration succeed". Click Close.
Once the IP-PT is successfully registered, the status of the IP-PT will update to show "Registered".

Registration of SIP Extensions
1.

a. Under Configuration, click Slot.
b. Move the mouse pointer over the white PBX
image at the bottom of the screen for the virtual
slots.
c. Click Select Shelf.
d. Move the mouse pointer over the V-SIPEXT32
card. A menu will be shown under the mouse
pointer.
e. Click Port Property.

Assign extension numbers to the SIP Extensions.
• If the Automatic Extension Number Set for
Extension Card feature is enabled, the extension
numbers of SIP Extension are automatically
assigned. To program this feature, refer to
"3.48 [1-3] Option— New Card Installation—
Automatic Extension Number Set for Extension
Card" in the PC Programming Manual.
• If not, enter the extension number for each SIP
Extension manually.

Document Version 2009-12

IP Networking Guide

4.6.1 Registering IP Telephones

Set passwords for the SIP Extensions.
a. Click the cell in the Connection column for each
SIP Extension you wish to register. The
Command Connection screen appears.
b. Click OUS.
c. Enter a password in the Password box for each
SIP Extension.
d. Click Apply.
e. Click the cell in the Connection column for each
SIP Extension to which a password has been
assigned. The Command Connection screen
appears.
f. Click INS.
g. Click OK.
Note
Alternatively, it is possible to set an extension
number as a password for each SIP Extension
automatically.

•

In order to set the password automatically, do the
following in substitution for step c of the procedure
above.
a. Click Copy to. A screen will appear with
information on assigned extension numbers
for SIP Extensions.
b. Click Select All.
c. Click Execute to copy each Extension
Number to Password.
d. Click Yes.
e. Click OK to return to the Port Property screen.

IP Networking Guide

Document Version 2009-12

4.6.1 Registering IP Telephones

Program the SIP Extension you wish to register.
[For SIP Extensions (except KX-HGT100)]

a. Set the IP address of the IPCMPR/IPCEMPR
card, extension number, and password in the
corresponding fields for your SIP Extension.
b. Send a request from the SIP Extension to the PBX
for registration.
• If the authentication information of the SIP
Extension and the PBX match, the
registration is successful.
Note

•

•
•

When programming the SIP Extension, the
names of the corresponding fields may differ
depending on the type of SIP Extension you
are using.
For details about the actual operation of SIP
Extensions, refer to the documentation of the
SIP Extension.
For certain SIP Extensions, you may need to
set a Sign-in name, which should consist of
the extension number and the IP address of
the IPCMPR/IPCEMPR card (e.g.,
350@192.168.0.101).

[For KX-HGT100 SIP Telephones]
It is necessary to program the KX-HGT100 through Web Programming to register to the PBX.
Follow the procedures below to prepare your PC for Web Programming and program the KX-HGT100.

Preparing the PC
System Requirements
• Microsoft® Internet Explorer® 6.0 or later
Trademarks
• Microsoft, Windows, and Internet Explorer are either registered trademarks or trademarks of Microsoft
Corporation in the United States and/or other countries.
• All other trademarks identified herein are the property of their respective owners.
Note
The procedures vary depending on the operating system of the PC.
This example is based on the Windows® XP operating system.
1.

Open Control Panel from the Start menu.

Document Version 2009-12

IP Networking Guide

4.6.1 Registering IP Telephones

a.
b.
c.
d.

Double-click Network Connections.
Double-click Local Area Connection.
Click Properties.
Confirm that Internet Protocol (TCP/IP) is listed.
Note
If Internet Protocol (TCP/IP) is not listed, you
must install TCP/IP. For details about
installation, refer to the documentation for
Windows XP.

Select Internet Protocol (TCP/IP) and click
Properties.

a. Select Use the following IP address:.
b. In the IP address box, type 192.168.0.201.
This is an example entry. Type an IP address
different from that assigned to the KX-HGT100 in
"4.5.1 Assigning the IP Addressing Information".
c. In the Subnet mask box, type 255.255.255.0.
d. Click OK.
Note
To obtain an IP address automatically, select
Obtain an IP address automatically.

a. Start Internet Explorer from the Start menu.
b. Click Internet Options from the Tools menu.

IP Networking Guide

Document Version 2009-12

4.6.1 Registering IP Telephones

a. Click the Connections tab.
b. Select Never dial a connection if necessary.
c. Click LAN Settings.

When Not Using a Proxy Server
Note
If you will use a proxy server, see When Using a
Proxy Server.

a. Clear all check boxes.
b. Click OK.
Your PC is now ready for programming through direct
access to the KX-HGT100.

When Using a Proxy Server
If the network has a proxy server installed, you must apply the appropriate proxy settings to your PC. In this
case, follow the steps below instead of step 7 above:
7.

a. Check all boxes for Proxy server.
b. Click Advanced.

Document Version 2009-12

IP Networking Guide

4.6.1 Registering IP Telephones

a. Under Do not use proxy server for addresses
beginning with:, type the IP address of the LAN
port of the card.
b. Click OK.
Your PC is now ready for programming the
KX-HGT100 through an IP network.

Programming the KX-HGT100
1.

Start Internet Explorer from the Start menu.

a. Enter the IP address of the KX-HGT100 in the address box.
b. Press the Enter key.

The log-in screen will appear.
a. In the User name box, type the user name (default: KX-HGT100).
b. In the Password box, type the password (default: kx-hgt100).
c. Click OK.

The top page will appear.
a. Click Basic Setting.
b. In the Telephone Number and SIP ID boxes, type
the extension number.
c. In the SIP Password box, type the password.
d. In the Proxy Address, Registrar Address, and
SIP Domain boxes, type the IP address of the
IPCMPR/IPCEMPR card.
e. Click Save.
f. Click Return to top page.
Note
For information on other parameters, refer to
Parameter Descriptions.

a. Click Restart.
b. Click Restart now for changes to take effect. The
KX-HGT100 will be restarted.
If the authentication information of the
KX-HGT100 and the PBX match, the registration
is successful.

Note
To access Web Programming after restarting the KX-HGT100, it is necessary to (1) turn the KX-HGT100
power off, and (2) hold the OK and MUTE buttons while turning the power on.

IP Networking Guide

Document Version 2009-12

4.6.1 Registering IP Telephones

Parameter Descriptions
Unit Status

Parameter

Description

Phone Number

Specifies the extension number of the KX-HGT100.

Unit Information

Specifies the status of the KX-HGT100 as follows:
• Update Profile: Basic Setting is not programmed (e.g., factory default).
• Registering: Registering the KX-HGT100 to the PBX.
• Normal: The KX-HGT100 is registered.
• Malfunctioning: The KX-HGT100 is in an error state.
• LAN cable unplugged: The LAN port of the KX-HGT100 is not receiving
any network signal.
• IP Address expired: IP address lease time from the DHCP server has
expired.
• IP Address conflict: The IP address of the KX-HGT100 conflicts with other
network devices.

Model

Specifies the model number of the KX-HGT100.

Operating Bank

Specifies the number of the memory bank for the current firmware.*1

IPL Version

Specifies the IPL (Initial Program Loader) version.

Firmware Version

Specifies the current firmware version of the KX-HGT100.

There are two memory banks. The Operating Bank number will cycle between these two memory banks, changing each time the
firmware is upgraded.

Document Version 2009-12

IP Networking Guide

4.6.1 Registering IP Telephones

Basic Setting

Parameter

Description

Language

Specifies the language to be displayed on the LCD.

Telephone Number*2

Specifies the extension number of the KX-HGT100.

SIP ID*2

Specifies the extension number of the KX-HGT100.

SIP Password

Specifies the password for the KX-HGT100.

Proxy Address*2

Specifies the IP address of the IPCMPR/IPCEMPR card.

Proxy Port*2

Specifies the port number associated with the IP address entered in Proxy
Address.

Registrar Address*2

Specifies the IP address of the IPCMPR/IPCEMPR card.

Registrar Port*2

Specifies the port number associated with the IP address entered in Registrar
Address.

SIP Domain*2

Specifies the IP address of the IPCMPR/IPCEMPR card.

Specifies the length of time (1–4294967295 seconds) that the KX-HGT100
sends the REGISTER message to the PBX.*1

Session Expire

Specifies the length of time (60–65535 seconds) after which the KX-HGT100
terminates SIP sessions when no communication is detected.

This setting will be overwritten by the SIP Location Hold Time Max. setting of the PBX. For details, refer to "3.17 [1-1] Slot—Card
Property - Virtual SIP Extension" in the PC Programming Manual.
These parameters can also be programmed by the KX-HGT100. For details about the procedure for the KX-HGT100, refer to "Basic
Setting programming through the KX-HGT100".

IP Networking Guide

Document Version 2009-12

4.6.1 Registering IP Telephones

Advanced Setting

Parameter

Description

RTP Port Min

Specifies the minimum port number for RTP transmission and reception (even
number only).

RTP Port Max

Specifies the maximum port number for RTP transmission and reception (even
number only).

Codec Priority

Specifies the codec types in order of priority. (The codec typed first has the
highest priority.)
Note
Calls are always established based on the calling party’s codec priority
setting.

Outband DTMF

Specifies whether to use Outband (RFC2833) DTMF tones or not. If NO is
selected, Inband DTMF tones will be used.

One time Caller ID Deny
Code

Specifies the number to dial when preventing the calling party’s telephone
number from being displayed on the called party’s telephone for outside
calls.*1

One time Caller ID
Permit Code

Specifies the number to dial when showing the calling party’s telephone
number on the called party’s telephone for outside calls.*1

SIP Listen Port

Specifies the port number to listen for incoming SIP calls.

RTP TOS

Specifies the ToS value in the IP header of RTP packets.

SIP TOS

Specifies the Diffserv (ToS) value in the IP header of SIP packets.

The number entered in this box has priority over features set via the PBX that use the same feature number.

Document Version 2009-12

IP Networking Guide

4.6.1 Registering IP Telephones

Basic Setting programming through the KX-HGT100
Follow the procedure below to program the Basic Setting parameters through the KX-HGT100.
Note

•
•

Before programming these settings, it is recommended to set the IP address of the KX-HGT100. For
details about setting IP addresses, refer to "For KX-HGT100 SIP Telephones" in "4.5.1 Assigning the
IP Addressing Information".
It is necessary to turn off, then turn on the power of the KX-HGT100 after programming settings for
changes to take effect.

To start programming

Press PROGRAM.

Hold INFORMATION for 3 seconds
while "Save speed dial?" is displayed.

To configure the Telephone Number/SIP ID

Extension No.
Select desired parameter.

Press OK.

Max. 5 digits

Press OK.

To configure the SIP Password

SIP Password
Select "SIP Password".

Press OK.

Max. 16 digits

Press OK.

To configure the Proxy Address/Registrar Address/SIP Domain

IP Address
Select desired parameter.

Press OK.

Enter the IP address of
the IPCMPR/IPCEMPR card.

Press OK.

To configure the Proxy Port/Registrar Port

Port No.
Select desired parameter.

Press OK.

1–65535

Press OK.

To end programming

Press PROGRAM.

IP Networking Guide

Document Version 2009-12

4.6.2 De-registering IP Telephones

4.6.2 De-registering IP Telephones
De-registration of IP-PTs
1.

a. Under Configuration, click Slot.
b. When de-registering from V-IPEXT32 Card:
Move the mouse pointer over the white PBX
image at the bottom of the screen for the virtual
slots, and click Select Shelf. Move the mouse
pointer over the V-IPEXT32 card. A menu will be
shown under the mouse pointer.
When de-registering from IP-EXT Card:
Move the mouse pointer over the IP-EXT card. A
menu will be shown under the mouse pointer.
c. Click Port Property.

Click De-registration.
A dialog box will appear. Registered extension
numbers and names are displayed on the left.

a. Highlight numbers and names and click the right
arrow to select them for de-registration.

b. Click Next.
A dialog box will appear.

c. Click Confirm.
• If the de-registration is successful, the dialog
box will show "De-registration succeed".

d. Click Close.

Once the IP-PT is successfully de-registered, the status of the IP-PT will update to show "None".

Document Version 2009-12

IP Networking Guide

4.6.2 De-registering IP Telephones

Forced De-registration of IP-PTs
Follow the steps below to forcibly de-register an IP-PT when normal de-registration was unsuccessful.
1.

Click Forced De-registration.
A dialog box will appear. Registered extension
numbers and names are displayed on the left.

a. Highlight numbers and names and click the right
arrow to select them for de-registration.

b. Click Next.
A dialog box will appear.

c. Click OK.
A dialog box will appear.
d. Click Confirm.
• If the de-registration is successful, the dialog
box will show "Forced de-registration
succeed".
e. Click Close.

Once the IP-PT is successfully de-registered, the status of the IP-PT will update to show "None".

IP Networking Guide

Document Version 2009-12

4.6.2 De-registering IP Telephones

De-registration of SIP Extensions
The de-registration of SIP Extensions is carried out by deleting either the extension number or password
registered in the PBX.
1.

Delete either the extension number or password in the
boxes shown right.

Document Version 2009-12

IP Networking Guide

5 Appendix

100

IP Networking Guide

Document Version 2009-12

5.1.1 KX-TDE100/KX-TDE200 PMMPR Software File Version 3.0xxx

5.1 Revision History
5.1.1 KX-TDE100/KX-TDE200 PMMPR Software File Version 3.0xxx
Changed Contents
•
•
•
•
•
•
•
•
•
•
•

1.1.1 Establishing a VoIP Network with the Pure IP-PBX
2.1.3 Network Devices
3.2 Connecting the IP Telephones
4.1.2 Installing Additional Activation Keys
4.3.1 Assigning the IP Addressing Information
4.5.1 Assigning the IP Addressing Information
4.5.2 Setting the VLAN Parameters
4.5.3 Setting the Diffserv Parameters
4.5.4 Configuration of IP Ports
4.6.1 Registering IP Telephones
5.2 Error Message

Document Version 2009-12

IP Networking Guide

101

5.1.2 KX-TDE600 PGMPR Software File Version 3.0xxx

5.1.2 KX-TDE600 PGMPR Software File Version 3.0xxx
Changed Contents
•
•
•
•
•
•
•
•
•
•
•

102

IP Networking Guide

Document Version 2009-12

5.2 Error Message

5.2 Error Message
When a major system error occurs, an error message is displayed on the IP-PT.
For IP-PTs with a single line display (e.g., KX-NT265), only an error code (i.e., ERR XXXX-XXXX) will be
displayed.
Note
For details for the KX-NT400, refer to the Operating Instructions of the KX-NT400.
Probable Cause

Error Message & IP-PT Activity
ERR 1001-0000
HARDWARE ERROR
Displays error and stops operating.

•

Sub CPU malfunction

ERR 1002-0000
HARDWARE ERROR
Displays error and stops operating.

•

Sound hardware
malfunction

ERR 1003-0000
HARDWARE ERROR
Displays error and stops operating.

•

Flash memory malfunction

ERR 1004-XXXX
HARDWARE ERROR
Displays error and stops operating.

•

PHY (network control IC)
error

ERR 1005-0000
HARDWARE ERROR
Displays error and stops operating.

•

SDRAM error

ERR 1006-0000
HARDWARE ERROR
Displays error and stops operating.

•

SRAM error

ERR 1007-0000
HARDWARE ERROR
Displays error and stops operating.

•

Sub CPU malfunction for
Self Labeling

ERR 1051-0000
SOFTWARE ERROR
Displays error and stops operating.

•

ERR 2001-XXXX
SYSTEM ERROR
Resets and displays error for 5 seconds
while starting up.
ERR 2002-0000
POOR LAN CONNECTION
Resets and displays error for 5 seconds
while starting up.
ERR 2003-0000
POOR LAN CONNECTION
Resets and displays error for 5 seconds
while starting up.

Document Version 2009-12

Solution

•

Repair or replace the
IP-PT.

PBX software version error

•

Consult your network
administrator.

•

Unexpected error

•

If this error is displayed
frequently, repair or
replace the IP-PT.

•

Transmission error

•

Check with the network
administrator whether
there is a problem with the
LAN.
If this error is displayed
frequently, repair or
replace the IP-PT.

•

IP Networking Guide

103

5.2 Error Message

Error Message & IP-PT Activity

104

Probable Cause

ERR 2004-0000
UNREGISTERED TO SERVER
Resets and displays error for 5 seconds
while starting up.

•

IP-PT not registered

ERR 2005-0000
NO MORE CONNECTIONS
Resets and displays error for 5 seconds
while starting up.

•

Connection refused by the
PBX

ERR 2006-XXXX
DHCP SERVER REJECTION
Resets and displays error for 5 seconds
while starting up.

•

ERR 2007-0000
HARDWARE ERROR
Resets and displays error for 5 seconds
while starting up.

Solution

•

Check the registration
status of the IP-PT.

IP address lease time from
DHCP server has expired
IP address lease renewal
was refused by DHCP
server

•

Consult your network
administrator.

•

Communication error with
sub CPU

•

If this error is displayed
frequently, repair or
replace the IP-PT.

ERR 2008-0000
HARDWARE ERROR
Resets and displays error for 5 seconds
while starting up.

•

Sound hardware control
error

ERR 2009-XXXX
MGCP SERVER REJECTION
Resets and displays error for 5 seconds
while starting up.

•

Error information from the
PBX (MGCP server)

•

Consult your network
administrator.

ERR 2010-0000
HARDWARE ERROR
Resets and displays error for 5 seconds
while starting up.

•

Communication error with
sub CPU for Self Labeling

•

If this error is displayed
frequently, repair or
replace the IP-PT.

ERR 3001-0000
HARDWARE ERROR
Displays error until reset the IP-PT.

•

Communication error with
sub CPU

ERR 3002-0000
HARDWARE ERROR
Displays error until reset the IP-PT.

•

Sound hardware control
error

ERR 3003-XXXX
DHCP SERVER NOT FOUND
Displays error until reset the IP-PT.

•

IP address lease renewal
was refused by DHCP
server

•

Consult your network
administrator.

ERR 3100-0000
BLUETOOTH ERROR
Resets the Bluetooth®*1 wireless
headset.

•

Bluetooth hardware error

•

Repair or replace the
Bluetooth wireless
headset.

•

The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Panasonic Corporation is
under license.

IP Networking Guide

Document Version 2009-12

Notes

Document Version 2009-12

IP Networking Guide

105

One Panasonic Way, Secaucus, New Jersey 07094
http://www.panasonic.com/csd
Copyright:
This material is copyrighted by Panasonic System Networks Co., Ltd., and may be reproduced for internal
use only. All other reproduction, in whole or in part, is prohibited without the written consent of Panasonic
System Networks Co., Ltd.
© Panasonic System Networks Co., Ltd. 2009

PSQX4184UA KK0607KE5129

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Create Date                     : 2009:11:17 11:52:23+09:00
Keywords                        : Panasonic KX-TDE100, KXTDE100, TDE100, KX-TDE200, KXTDE200, TDE200, KX-TDE600, KXTDE600, TDE600, panasonic ip, ip networking, networking guide, ip guide, panasonic guide, pure ip-pbx, panasonic system, telephone system
Modify Date                     : 2010:06:14 15:08:27-04:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Format                          : application/pdf
Creator                         : 
Description                     : Panasonic KX-TDE100 200 600 IP Networking Guide Pure IP-PBX
Title                           : Panasonic KX-TDE100 200 600 IP Networking Guide Pure IP-PBX
Subject                         : Panasonic KX-TDE100, KXTDE100, TDE100, KX-TDE200, KXTDE200, TDE200, KX-TDE600, KXTDE600, TDE600, panasonic ip, ip networking, networking guide, ip guide, panasonic guide, pure ip-pbx, panasonic system, telephone system
Creator Tool                    : XSL Formatter V4.3 MR6b (4,3,2009,0204) for Windows
Metadata Date                   : 2010:06:14 15:08:27-04:00
Producer                        : Antenna House PDF Output Library 2.6.0 (Windows)
Document ID                     : uuid:44224427-0855-4153-a58e-92f1f80f664e
Instance ID                     : uuid:831da8d2-c5b1-42ea-ad5b-a279b35a135b
Page Mode                       : UseOutlines
Page Count                      : 106

EXIF Metadata provided by EXIF.tools

Panasonic KX TDE100 200 600 IP Networking Guide Pure PBX TDE200 TDE600 KXTDE 100

Navigation menu

Versions of this User Manual:

Views

Navigation