Keysight_N5230C_PNA L_Microwave_Network_Analyzer_5989 7607EN Datasheet Keysight N5230C PNA L Microwave Network Analyzer 5989
User Manual: Keysight_N5230C_PNA-L_Microwave_Network_Analyzer_5989-7607EN-datasheet
Open the PDF directly: View PDF 
.
Page Count: 39
| Download | |
| Open PDF In Browser | View PDF |
Keysight Technologies 2-Port PNA-L Microwave Network Analyzer N5230C 300 kHz to 6, 13.5 GHz 10 MHz to 20, 40, 50 GHz Data Sheet Specification information in this document is also available within the PNA-L network analyzer’s internal Help system. Table of Contents Definitions ............................................................... 3 Corrected System Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Table 1. System dynamic range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Table 2. Extended dynamic range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 N5230C Corrected system performance with 3.5 mm connectors. . . . . . . . . . . . . . . . . 6 Table 3. 85052B Calibration kit N5230C – Configurable test set and extended power range (Option 025 or 125). . . . . . . 6 Table 4. 85052B Calibration kit N5230C – Configurable test set and extended power range (Option 225) . . . . . . . . . . . . 8 Table 5. N4691A Electronic calibration module N5230C – Configurable test set and extended power range (Option 225) . . . . . . . . . . . 10 Table 6. 85056A Calibration kit N5230C – Configurable test set and extended power range (Option 425 or 525). . . . . . 12 Table 7. N4693A Electronic calibration module N5230C – Configurable test set and extended power range (Option 425 or 525). . . . . . 14 N5230C Corrected system performance with Type-N connectors . . . . . . . . . . . . . . . . 16 Table 8. N5232B Calibration kit N5230C – Configurable test set and extended power range (Option 025) . . . . . . . . . . . 16 Table 9. Uncorrected system performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Table 10. Test port output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Table 11. Test port input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Dynamic Accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Table 12. Test port input (group delay). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 13. Miscellaneous information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 14. Front panel information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 15. Rear panel information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 16. Analyzer environment and dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . 26 26 26 27 28 Measurement Throughput Summary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 17. Typical cycle time (ms) for measurement completion . . . . . . . . . . . . . . Table 18. Cycle time vs IF bandwidth (Options 020, 025, 120, 125) . . . . . . . . . . . . Table 19. Cycle time vs IF bandwidth (Options 220, 225, 420, 425) . . . . . . . . . . . . Table 20. Cycle time vs number of points (Options 020, 025, 120, 125) . . . . . . . . Table 21. Cycle time vs number of points (Options 220, 225,420, 425, 520, 525) . Table 22. Data transfer time (ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 29 30 31 32 33 34 Specifications: Front-Panel Jumpers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 23: Measurement receiver inputs (Rcvr A In, Rcvr B In) . . . . . . . . . . . . . . . Table 24: Reference receiver inputs (Rcvr R1, Rcvr R2) . . . . . . . . . . . . . . . . . . . . . Table 25: Reference outputs (Reference 1 Source out, Reference 2 Source Out) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 26: Source outputs (Port 1 source out, Port 2 Source Out) . . . . . . . . . . . . . Table 27: Coupler inputs (port 1 Cplr Thru, Port 2 Cplr Thru). . . . . . . . . . . . . . . . . Table 28: Coupler outputs (port 1 Cplr Arm, Port 2 Cplr Arm) . . . . . . . . . . . . . . . . 35 35 36 36 37 37 37 Test Set Block Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 N5230C Option 220, or 420, or 520 (standard test set and standard power range) network analyzer . . . . . . . . . . 38 N5230C Option 225, or 425, or 525 (configurable test set and extended power range) network analyzer . . . . . . 38 Web Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 2 This is a subset of technical specifications for the Keysight Technologies, Inc. N5230C network analyzer. To view or print the N5230C technical specifications, visit our web site at www.keysight.com/find/pnal This N5230C document provides technical specifications for the following calibration kits and ECal modules only: 85052B, 85056A, 85032B, N4691A, and N4693A. Please download our free Uncertainty Calculator from www.keysight.com/find/na_calculator to generate the curves for your calibration kit and PNA setup. Deinitions All specifications and characteristics apply over a 25 °C ±5 °C range (unless otherwise stated) and 90 minutes after the instrument has been turned on. Specification (spec.): Warranted performance. Specifications include guardbands to account for the expected statistical performance distribution, measurement uncertainties, and changes in performance due to environmental conditions. Characteristic (char.): A performance parameter that the product is expected to meet before it leaves the factory, but that is not verified in the field and is not covered by the product warranty. A characteristic includes the same guardbands as a specification. Typical (typ.): Expected performance of an average unit which does not include guardbands. It is not covered by the product warranty. Nominal (nom.): A general, descriptive term that does not imply a level of performance. It is not covered by the product warranty. Calibration: The process of measuring known standards to characterize a network analyzer's systematic (repeatable) errors. Corrected (residual): Indicates performance after error correction (calibration). It is determined by the quality of calibration standards and how well "known" they are, plus system repeatability, stability, and noise. Uncorrected (raw): Indicates instrument performance without error correction. The uncorrected performance affects the stability of a calibration. Standard: When referring to the analyzer, this includes no options unless noted otherwise. 3 Corrected System Performance The specifications in this section apply for measurements made with the N5230C analyzer with the following conditions: – 10 Hz IF bandwidth – No averaging applied to data – Isolation calibration with an averaging factor of 8 Table 1. System dynamic range1 Standard configuration and standard power range Description 300 kHz to 3 MHz3 3 to 10 MHz 10 to 45 MHz 5 to 70 MHz2 70 to 500 MHz2 500 MHz to 2 GHz 2 to 6 GHz 6 to 8 GHz 8 to 9 GHz 9 to 10.5 GHz 10.5 to 12.5 GHz 12.5 to 13.5 GHz 13.5 to 20 GHz 20 to 31.25 GHz 31.25 to 40 GHz 40 to 50 GHz Speciication (dB) at test port Option Option Option Option 020, 120 220 420 520 934 113 122 122 101 90 90 122 105 90 90 122 110 110 110 122 110 110 110 120 110 110 110 120 110 100 100 116 110 100 100 111 110 100 100 109 108 100 100 108 100 100 95 95 90 90 79 Typical (dB) at test port Option Option Option 020, 120 220 420 103 89 Option 520 89 Configurable test set and extended power range Description 300 kHz to 3 MHz3 3 to 10 MHz 10 to 45 MHz 45 to 70 MHz2 70 to 500 MHz2 500 MHz to 2 GHz 2 to 6 GHz 6 to 8 GHz 8 to 9 GHz 9 to 10.5 GHz 10.5 to 12.5 GHz 12.5 to 13.5 GHz 13.5 to 20 GHz 20 to 31.25 GHz 31.25 to 40 GHz 40 to 50 GHz Speciication (dB) at test port Option Option Option Option 025, 125 225 425 525 924 112 121 121 101 90 90 121 105 90 90 121 110 110 110 121 110 110 110 120 110 110 110 120 110 100 100 116 110 100 100 111 110 100 100 108 108 100 100 108 100 100 92 92 87 87 75 Typical (dB)at test port Option Option Option 025, 125 225 425 103 88 Option 525 88 1. The system dynamic range is calculated as the difference between the noise floor and the specified source maximum output power. The effective dynamic range must take measurement uncertainties and interfering signals into account. 2. May be degraded typically by 10 dB at particular frequencies (multiples of 5 MHz) below 500 MHz due to spurious receiver residuals. Methods are available to regain the full dynamic range. 3. May be limited by crosstalk at certain frequencies below 3 MHz. 4 4. Value and frequency band changed July 2006. Table 2. Extended dynamic range1 Configurable test set and extended power range 300 kHz to 3 MHz3 Speciication (dB) at direct receiver access input Option 025, 125 Option 225 Option 425 Option 525 1084 3 to 10 MHz 128 Description 10 to 45 MHz 137 45 to 70 MHz2 137 115 113 111 137 117 111 111 500 MHz to 2 GHz 137 122 122 122 2 to 6 GHz 137 122 122 122 6 to 8 GHz 136 122 122 122 8 to 9 GHz 136 122 122 122 9 to 10.5 GHz 132 122 112 112 10.5 to 12.5 GHz 127 122 112 112 12.5 to 13.5 GHz 124 120 112 112 120 112 112 20 to 31.25 GHz 103 103 31.25 to 40 GHz 98 98 40 to 50 GHz 109 Option 525 109 111 70 to 500 MHz2 13.5 to 20 GHz Typical (dB) at direct receiver access input Option 025, 125 Option 225 Option 425 83 1. The direct receiver access input extended dynamic range is calculated as the difference between the direct receiver access input noise floor and the source maximum output power. The effective dynamic range must take measurement uncertainties and interfering signals into account. This set-up should only be used when the receiver input will never exceed its compression or damage level. When the analyzer is in segment sweep mode, it can have predefined frequency segments which will output a higher power level when the extended dynamic range is required (i.e. devices with high insertion loss), and reduced power when receiver compression or damage may occur (i.e. devices with low insertion loss). The extended range is only available in one-path transmission measurements. 2. May be degraded typically by 10 dB at particular frequencies (multiples of 5 MHz) below 500 MHz due to spurious receiver residuals. Methods are available to regain the full dynamic range. 3. May be limited by crosstalk at certain frequencies below 3 MHz. 4. Value and frequency band changed July 2006. 5 N5230C Corrected system performance with 3.5 mm connectors Table 3. 85052B Calibration kit N5230C – configurable test set and extended power range (Option 025, 125) Configurable test set, extended power range Applies to the N5230C Option 025 and 125 analyzers, 85052B (3.5 mm) calibration kit, 85131F flexible test port cable set, and a full 2-port calibration. Also applies to the following condition: Environmental temperature 23° ±3 °C, with < 1 °C deviation from calibration temperature. Speciication (dB) Description 300 kHz to 10 MHz 10 MHz to 2 GHz 2 to 8 GHz 8 to 13.5 GHz Directivity 48 48 44 44 Source match 40 40 33 31 Load match 48 48 44 44 Reflection tracking ±0.003 (+0.02/°C) ±0.003 (+0.02/°C) ±0.003 (+0.03/°C) ±0.006 (+0.03/°C) Transmission tracking ±0.017 (+0.02/°C) ±0.015 (+0.02/°C) ±0.075 (+0.03/°C) ±0.131 (+0.03/°C) Transmission uncertainty (specifications) Magnitude N5230C 025/125 Full Two Port Cal Using 85052B Uncertainty (dB) 10 300 KHz to 10 MHz 10 MHz to 2 GHz 2 to 8 GHz 8 to 13.5 GHz 1 0.1 S11 = S22 = 0 Source power = 0 dBm 0.01 10 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 Transmission coefficient (dB) Phase N5230C 025/125 Full Two Port Cal Using 85052B Uncertainty (degrees) 100 300 KHz to 10 MHz 10 MHz to 2 GHz 2 to 8 GHz 8 to 13.5 GHz 10 1 S11 = S22 = 0 Source power = 0 dBm 0.1 10 0 -10 -20 -30 -40 -50 -60 Transmission coefficient (dB) 6 -70 -80 -90 Reflection uncertainty (specifications) Magnitude N5230C 025/125 with 85052B 0.05 300 kHz to 10 MHz 10 MHz to 2 GHz 2 to 8 GHz 8 to 13.5 GHz Uncertainty (linear) 0.04 0.03 S21 = S12 = 0 Source power = 0 dBm 0.02 0.01 0 0 0.2 0.4 0.6 0.8 1 Reflection coefficient (linear) Phase N5230C 025/125 with 85052B 10 300 kHz to 10 MHz 10 MHz to 2 GHz 2 to 8 GHz 8 to 13.5 GHz Uncertainty (deg) 8 6 S21 = S12 = 0 Source power = 0 dBm 4 2 0 0 0.2 0.4 0.6 0.8 1 Reflection coefficient (linear) 7 N5230C Corrected system performance with 3.5 mm connectors Table 4. 85052B Calibration kit N5230C – configurable test set and extended power range (Option 225) Configurable test set, extended power range Applies to the N5230C Option 225 analyzers, 85052B (3.5 mm) calibration kit, 85131F flexible test port cable set, and a full 2-port calibration. Also applies to the following condition: Environmental temperature 23° ±3 °C, with < 1 °C deviation from calibration temperature. Speciication (dB) Description 45 to 500 MHz 500 MHz to 2 GHz 2 to 8 GHz 8 to 20 GHz Directivity 48 48 44 44 Source match 40 40 33 31 Load match 48 48 44 44 Reflection tracking ±0.003 (+0.02/°C) ±0.003 (+0.02/°C) ±0.003 (+0.03/°C) ±0.006 (+0.03/°C) Transmission tracking ±0.010 (+0.02/°C) ±0.014 (+0.02/°C) ±0.062 (+0.03/°C) ±0.104 (+0.03/°C) Transmission uncertainty (specifications) Magnitude N5230C 225 Full Two Port Cal Using 85052B Uncertainty Uncertainty (dB) (dB) 10 45 to 500 MHz 500 MHz to 2 GHz 2 to 8 GHz 8 to 20 GHz 1 0.1 S11 = S22 = 0 Source power = -5 dBm 0.01 10 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 Transmission coefficient (dB) Phase N5230C 225 Full Two Port Cal Using 85052B Uncertainty (degrees) 100 45 to 500 MHz 500 MHz to 2 GHz 2 to 8 GHz 8 to 20 GHz 10 1 S11 = S22 = 0 Source power = -5 dBm 0.1 10 0 -10 -20 -30 -40 -50 -60 Transmission coefficient (dB) 8 -70 -80 -90 N4691A Electronic calibration module N5230C – configurable test set and extended power range (Option 225) Reflection uncertainty (specifications) Magnitude Uncertainty (linear) N5230C Option 225 with 85052B 45 to 500 MHz 500 MHz to 2 GHz 2 to 8 GHz 8 to 20 GHz Reflection coefficient (linear) Phase Uncertainty (deg) N5230C Option 225 with 85052B 45 to 500 MHz 500 MHz to 2 GHz 2 to 8 GHz 8 to 20 GHz Reflection coefficient (linear) 9 N5230C Corrected system performance with 3.5 mm connectors Table 5. N4691B Electronic calibration module N5230C – configurable test set and extended power range (Option 225) Configurable test set, extended power range Applies to the N5230C Option 225 analyzers, N4691B electronic calibration module, 85131F flexible test port cable set, and a full 2-port calibration. Also applies to the following condition: Environmental temperature 23° ±3 °C, with < 1 °C deviation from calibration temperature. Speciication (dB) Description 45 to 500 MHz 500 MHz to 2 GHz 2 to 8 GHz 8 to 20 GHz Directivity 46 56 54 48 Source match 41 47 45 44 Load match 41 47 44 42 Reflection tracking ±0.050 (+0.02/°C) ±0.020 (+0.02/°C) ±0.030 (+0.03/°C) ±0.040 (+0.03/°C) Transmission tracking ±0.053 (+0.02/°C) ±0.021 (+0.02/°C) ±0.034 (+0.03/°C) ±0.052 (+0.03/°C) Transmission uncertainty (specifications) Magnitude N5230C 225 Full Two Port Cal Using N4691B Uncertainty (dB) 10 45 to 500 MHz 500 MHz to 2 GHz 2 to 8 GHz 8 to 20 GHz 1 0.1 S11 = S22 = 0 Source power = -5 dBm 0.01 10 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 Transmission coefficient (dB) Phase N5230C 225 Full Two Port Cal Using N4691B Uncetainty (degrees) 100 45 to 500 MHz 500 MHz to 2 GHz 2 to 8 GHz 8 to 20 GHz 10 1 S11 = S22 = 0 Source power = -5 dBm 0.1 10 0 -10 -20 -30 -40 -50 -60 Transmission coefficient (dB) 10 -70 -80 -90 N4691A Electronic calibration module N5230C – configurable test set and extended power range (Option 225) Reflection uncertainty (specifications) Magnitude N5230C 225 with N4691B Uncertainty (linear) 0.05 45 to 500 MHz 500 MHz to 2 GHz 2 to 8 GHz 8 to 20 GHz 0.04 0.03 S21 = S12 = 0 Source power = -5 dBm 0.02 0.01 0 0 0.2 0.4 0.6 0.8 1 Reflection coefficient (linear) Phase N5230C 225 with N4691B 10 45 MHz to 500 MHz 500 MHz to 2 GHz 2 to 8 GHz 8 to 20 GHz Uncetainty (deg) 8 6 S21 = S12 = 0 Source power = -5 dBm 4 2 0 0 0.2 0.4 0.6 0.8 1 Reflection coefficient (linear) 11 N5230C Corrected system performance with 2.4 mm connectors Table 6. 85056A Calibration kit N5230C – configurable test set and extended power range (Option 425 or 525) Configurable test set, extended power range Applies to the N5230C Option 425 or 525 analyzers, 85056A (2.4 mm) electronic calibration module, 85133F flexible test port cable set, and a full 2-port calibration. Also applies to the following condition: Environmental temperature 23° ±3 °C, with < 1 °C deviation from calibration temperature. Speciication (dB) Description 45 MHz to 2 GHz 2 to 20 GHz 20 to 40 GHz 40 to 50 GHz Directivity 42 42 38 36 Source match 41 38 33 31 Load match 42 42 37 35 Reflection tracking ±0.001 (+0.02/°C) ±0.008 (+0.02/°C) ±0.020 (+0.02/°C) ±0.027 (+0.03/°C) Transmission tracking ±0.019 (+0.02/°C) ±0.057 (+0.02/°C) ±0.124 (+0.02/°C) ±0.211 (+0.03/°C) Transmission uncertainty (specifications) Magnitude N5230C 425 & 525 Full Two Port Cal Using 85056A Uncertainty (dB) 10 45 MHz to 2 GHz 2 to 20 GHz 20 to 40 GHz 40 to 50 GHz 1 0.1 S11 = S22 = 0 Source Power = -15 dBm 0.01 10 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 Transmission coefficient (dB) Phase N5230C 425 & 525 Full Two Port Cal Using 85056A Uncertainty (degrees) 100 45 MHz to 2 GHz 2 to 20 GHz 20 to 40 GHz 40 to 50 GHz 10 1 S11 = S22 = 0 Source Power = -15 dBm 0.1 10 0 -10 -20 -30 -40 -50 -60 Transmission coefficient (dB) 12 -70 -80 -90 Reflection uncertainty (specifications) Magnitude N5230C 425 & 525 with 85056A Uncertainty (linear) 0.05 45 MHz to 2 GHz 2 to 20 GHz 20 to 40 GHz 40 to 50 GHz 0.04 0.03 S21 = S12 = 0 Source power = -15 dBm 0.02 0.01 0 0 0.2 0.4 0.6 0.8 1 Reflection coefficient (linear) Phase N5230C 425 & 525 with 85056A 10 45 MHz to 2 GHz 2 to 20 GHz 20 to 40 GHz 40 to 50 GHz Uncertainty (deg) 8 6 S21 = S12 = 0 Source Power = -15 dBm 4 2 0 0 0.2 0.4 0.6 0.8 1 Reflection coefficient (linear) 13 Table 7. N4693A Electronic calibration module N5230C – configurable test set and extended power range (Option 425 or 525) Configurable test set, extended power range Applies to the N5230C Option 425 or 525 analyzers, N4693A (2.4 mm) electronic calibration module, 85133F flexible test port cable set, and a full 2-port calibration. Also applies to the following condition: Environmental temperature 23° ±3 °C, with < 1 °C deviation from calibration temperature. Typical (dB) Speciication (dB) Description 10 to 200 MHz 200 MHz to 2 GHz 2 to 20 GHz 20 to 40 GHz 40 to 50 GHz Directivity 32 55 49 43 41 Source match 25 46 42 35 30 Load match 24 43 41 37 36 Reflection tracking ±0.05 (+0.02/°C) ±0.030 (+0.02/°C) ±0.040 (+0.02/°C) ±0.060 (+0.02/°C) ±0.080 (+0.03/°C) Transmission tracking ±0.10 (+0.02/°C) ±0.056 (+0.02/°C) ±0.078 (+0.02/°C) ±0.107 (+0.02/°C) ±0.130 (+0.03/°C) Transmission uncertainty (specifications) Magnitude N5230C 425 & 525 Full Two Port Cal Using N4693A Uncertainty (dB) 10 200 MHz to 2 GHz 2 to 20 GHz 20 to 40 GHz 40 to 50 GHz 1 0.1 S11 = S22 = 0 Source power = -15 dBm 0.01 10 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 Transmission coefficient (dB) Phase N5230C 425 & 525 Full Two Port Cal Using N4693A Uncertainty (degrees) 100 200 MHz to 2 GHz 2 to 20 GHz 20 to 40 GHz 40 to 50 GHz 10 1 S11 = S22 = 0 Source power = -15 dBm 0.1 10 0 -10 -20 -30 -40 -50 -60 Transmission coefficient (dB) 14 -70 -80 -90 Reflection uncertainty (specifications) Magnitude N5230C 425 & 525 with N4693A 0.05 0.04 Uncertainty (linear) S21 = S12 = 0 Source power = -15 dBm 200 MHz to 2 GHz 2 to 20 GHz 20 to 40 GHz 40 to 50 GHz 0.03 0.02 0.01 0 0 0.2 0.4 0.6 0.8 1 Reflection coefficient (linear) Phase N5230C 425 & 525 with N4693A 10 200 MHz to 2 GHz 2 to 20 GHz 20 to 40 GHz 40 to 50 GHz Uncertainty (deg) 8 6 S21 = S12 = 0 Source power = -15 dBm 4 2 0 0 0.2 0.4 0.6 0.8 1 Reflection coefficient (linear) 15 N5230C Corrected system performance with Type-N connectors Table 8. 85032B Calibration kit N5230C – configurable test set and extended power range (Option 025) Configurable test set, extended power range Applies to the N5230C Option 025 analyzers, 85032B (Type-N) calibration kit, 85132F flexible test port cable set with 85130C adapter set, and a full 2-port calibration. Also applies to the following condition: Environmental temperature 23° ±3 °C, with < 1 °C deviation from calibration temperature. Speciication (dB) Description 300 kHz to 1 MHz 1 to 10 MHz 10 to 45 MHz 45 MHz to 6 GHz Directivity 50 50 47 40 Source match 42 42 37 31 Load match 50 50 47 38 Reflection tracking ±0.009 (+0.01/°C) ±0.009 (+0.01/°C) ±0.019 (+0.01/°C) ±0.069 (+0.02/°C) Transmission tracking ±0.013 (+0.01/°C) ±0.007 (+0.01/°C) ±0.021 (+0.01/°C) ±0.101 (+0.02/°C) Transmission uncertainty (specifications) Magnitude N5230C 025 Full Two Port Cal Using 85032B Uncertainty (dB) 10 300 KHz to 10 MHz 10 to 500 MHz 500 MHz to 2 GHz 2 to 6 GHz 1 0.1 S11 = S22 = 0 Source power = 0 dBm 0.01 10 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 Transmission coefficient (dB) Phase N5230C 025 Full Two Port Cal Using 85032B Uncertainty (degrees) 100 300 KHz to 10 MHz 10 to 500 MHz 500 MHz to 2 GHz 2 to 6 GHz 10 1 S11 = S22 = 0 Source power = 0 dBm 0.1 10 0 -10 -20 -30 -40 -50 -60 Transmission coefficient (dB) 16 -70 -80 -90 Transmission uncertainty (specifications) Magnitude N5230C 025 with 85032B 0.05 300 kHz to 10 MHz 10 to 500 MHz 500 MHz to 2 GHz 2 to 6 GHz Uncertainty (linear) 0.04 0.03 S21 = S12 = 0 Source power = 0 dBm 0.02 0.01 0 0 0.2 0.4 0.6 0.8 1 Reflection coefficient (linear) Phase N5230C 025 with 85032B 10 300 kHz to 10 MHz 10 to 500 MHz 500 MHz to 2 GHz 2 to 6 GHz Uncertainty (deg) 8 6 S21 = S12 = 0 Source power = 0 dBm 4 2 0 0 0.2 0.4 0.6 0.8 1 Reflection coefficient (linear) 17 Table 9. Uncorrected system performance Directivity Speciications Option 020, 025, 120, 125 300 kHz to 10 MHz 10 to 45 MHz 45 to 500 MHz 500 MHz to 1 GHz 1 to 2 GHz 2 to 3 GHz 3 to 5 GHz 5 to 8 GHz 8 to 11.5 GHz 11.5 to 13.5 GHz 13.5 to 20 GHz 20 to 40 GHz 40 to 50 GHz 16 dB 28 dB 28 dB 28 dB 25 dB 25 dB 20 dB 17 dB 17 dB 15 dB Source match Option 020, 025, 120, 125 300 kHz to 10 MHz 10 to 45 MHz 45 to 500 MHz 500 MHz to 2 GHz 2 to 3 GHz 3 to 8 GHz 8 to 9 GHz 9 to 12.5 GHz 12.5 to 13.5 GHz 13.5 to 20 GHz 20 to 40 GHz 40 to 50 GHz 18 dB 25 dB 25 dB 21 dB 19 dB 12 dB 12 dB 10 dB 8 dB Load match Option 020, 025, 120, 125 300 kHz to 10 MHz 10 to 45 MHz 45 to 500 MHz 500 MHz to 2 GHz 2 to 3 GHz 3 to 8 GHz 8 to 9 GHz 9 to 12.5 GHz 12.5 to 13.5 GHz 13.5 to 20 GHz 20 to 40 GHz 40 to 50 GHz 17 dB 22 dB 22 dB 17 dB 14 dB 10 dB 9 dB 9 dB 7 dB Option 220, 225 Option 420, 425 Option 520, 525 24 dB 27 dB 27 dB 21 dB 21 dB 21 dB 16 dB 16 dB 16 dB 23 dB 23 dB 23 dB 21 dB 21 dB 21 dB 16 dB 16 dB 16 dB 15 dB 23 dB 23 dB 23 dB 21 dB 21 dB 21 dB 16 dB 16 dB 16 dB 15 dB 13 dB Option 220, 225 Option 420, 425 Option 520, 525 20 dB 17 dB 12 dB 12 dB 11 dB 11 dB 10 dB 10 dB 17 dB 17 dB 12 dB 12 dB 11 dB 11 dB 11 dB 11 dB 7 dB 17 dB 17 dB 12 dB 12 dB 11 dB 11 dB 11 dB 11 dB 7 dB 6 dB Option 220, 225 Option 420, 520 Option 425, 525 22 dB 20 dB 12 dB 12 dB 10 dB 10 dB 9 dB 9 dB 18 dB 18 dB 14 dB 14 dB 12 dB 12 dB 9 dB 9 dB 8 dB 18 dB 18 dB 14 dB 14 dB 12 dB 12 dB 9.5 dB 9.5 dB 8.5 dB 5 dB Typicals Option 020, 025, 120, 125 Option 020, 025, 120, 125 Option 020, 025, 120, 125 Crosstalk1 Option 020, 025, 120, 125 300 kHz to 10 MHz 10 to 45 MHz 45 to 500 MHz 500 MHz to 2 GHz 2 to 8 GHz 8 to 10.5 GHz 10.5 to 12.5 GHz 12.5 to 13.5 GHz 13.5 to 20 GHz 20 to 40 GHz 40 to 50 GHz 75 dB2 115 dB 122 dB 122 dB 122 dB 120 dB 115 dB 109 dB Option 220, 225 Option 420, 425 Option 520, 525 23 dB 20 dB 20 dB Option 220, 225 Option 420, 425 Option 520, 525 12 dB 11 dB 11 dB Option 220, 225 Option 420, 425 Option 520, 525 15 dB 13 dB 13 dB Option 220, 225 Option 420, 425 Option 520, 525 88 dB 95 dB 96 dB 110 dB 116 dB 116 dB 115 dB 115 dB 88 dB 94 dB 95 dB 108 dB 113 dB 113 dB 112 dB 112 dB 97 dB 88 dB 94 dB 95 dB 108 dB 113 dB 113 dB 112 dB 112 dB 97 dB 89 dB 1. Measurement conditions: normalized to a thru, measured with two shorts, 10 Hz IF bandwidth, averaging factor of 8, alternate mode, source power set to the specified maximum power output or the minimum receiver input power specified by the 0.1 dB compression power 2. Value changed July 2006. 18 Table 10. Test port output1 Description Speciications Typicals Option 020, 025 Option 120, 125 Option 220, 225 Option 420, 425 Option 520, 525 300 kHz to 6 GHz 300 kHz to 13.5 GHz 10 MHz to 20 GHz 10 MHz to 40 GHz 10 MHz to 50 GHz Option 020, 025, 120, 125 Option 220, Option 420, Option 520, 225 425 525 Frequency range N5230C Nominal power Preset power; attenuator switch point 10 dB below nominal power 0 dBm 0 dBm –5 dBm –10 dBm Frequency resolution 1 Hz CW accuracy ±1 ppm Frequency stability –15 dBm ±0.05 ppm. –10° to 70° C ±0.1 ppm/yr maximum Description Speciications Typicals Option 020, 025, 120, 125 Power level accuracy Variation from nominal power in range 0 300 kHz to 10 MHz ±1.0 dB 10 to 45 MHz ±1.0 dB 45 MHz to 6 GHz ±1.0 dB 6 to 8 GHz ±1.5 dB 8 to 9 GHz ±1.5 dB 9 to 10.5 GHz ±1.5 dB 10.5 to 13.5 GHz ±2.0 dB 13.5 to 20 GHz 20 to 40 GHz 40 to 50 GHz Description Max leveled power 300 kHz to 10 MHz 10 to 45 MHz 45 MHz to 6 GHz 6 to 9 GHz 9 to 12.5 GHz 12.5 to 13.5 GHz 13.5 to 20 GHz 20 to 40 GHz 40 to 50 GHz Power level linearity 2 300 kHz to 1 MHz 1 to 10 MHz 10 to 45 MHz 45 MHz to 1 GHz 1 to 12.5 GHz 12.5 to 13.5 GHz 13.5 to 20 GHz 20 to 40 GHz 40 to 50 GHz Option 220, 225 Option 420, 425 Option 520 Option 525 ±1.0 dB ±1.0 dB ±1.0 dB ±1.0 dB ±1.0 dB ±1.0 dB ±1.0 dB ±1.0 dB ±1.5 dB ±1.5 dB ±1.5 dB ±1.5 dB ±2.5 dB ±1.0 dB ±1.0 dB ±1.5 dB ±1.5 dB ±1.5 dB ±1.5 dB ±2.5 dB ±3.5 dB ±1.0 dB ±1.0 dB ±1.5 dB ±1.5 dB ±1.5 dB ±1.5 dB ±2.5 dB ±3.5 dB Option 020, 025, 120, 125 Speciications Option 420, 425, 520, 525 ±0.5 dB ±0.5 dB Typicals Option 020, 120 Option 025, 125 10 dBm 10 dBm 10 dBm 8 dBm 4 dBm 2 dBm 9 dBm 9 dBm 9 dBm 8 dBm 4 dBm 1 dBm Option 220, 225 Option 420 Option 425 Option 520 Option 525 5 dBm 5 dBm 5 dBm 3 dBm 3 dBm 0 dBm 0 dBm 0 dBm 0 dBm 0 dBm –5 dBm 0 dBm 0 dBm 0 dBm 0 dBm 0 dBm –8 dBm 0 dBm 0 dBm 0 dBm 0 dBm 0 dBm –5 dBm –11 dBm 0 dBm 0 dBm 0 dBm 0 dBm 0 dBm –8 dBm –15 dBm ±2.0 dB ±1.5 dB ±1.5 dB Option 220, 225 5 dBm Options as indicated ±2.0 dB (Opt 020, 025, 120, 125) Test reference is at the nominal power level ±4.5 dB ±4.5 dB ±1.0 dB ±1.0 dB ±2.0 dB ±2.0 dB ±2.0 dB ±1.5 dB ±1.5 dB Option 220, 225 ±1.0 dB ±1.0 dB ±1.0 dB ±1.0 dB ±0.35 dB (Opt 220, 225) ±0.40 dB (Opt 420, 425, 520, 525) ±1.0 dB ±1.0 dB ±1.0 dB ±1.0 dB ±1.0 dB ±1.0 dB ±1.0 dB ±1.0 dB ±1.0 dB ±1.0 dB ±1.0 dB ±1.0 dB ±1.0 dB ±1.0 dB ±1.0 dB ±1.0 dB ±1.0 dB ±1.0 dB ±1.0 dB ±1.0 dB ±1.0 dB ±1.0 dB 1. Performance specified on Port 1 only. Port 2 performance is a characteristic. 2. Power level linearity specified on Port 1 only. Port 2 performance is typical. Test reference is at the nominal power level. 19 Table 10. Test port output1 (Continued) Description Speciications Typicals Option 020, 120 Option 025, 125 Option 220, 225 Option 420 Option 425 Option 520 Option 525 Option 220, 225 Power sweep range (ALC)2 300 kHz to 10 MHz 10 to 45 MHz 45 MHz to 6 GHz 6 to 9 GHz 9 to 12.5 GHz 12.5 to 13.5 GHz 13.5 to 20 GHz 20 to 40 GHz 40 to 50 GHz Power resolution 37 dB 37 dB 37 dB 35 dB 31 dB 29 dB Description 36 dB 36 dB 36 dB 35 dB 31 dB 28 dB 25 dB 25 dB 25 dB 25 dB 23 dB 23 dB 25 dB 25 dB 25 dB 25 dB 25 dB 20 dB 25 dB 25 dB 25 dB 25 dB 25 dB 17 dB 25 dB 25 dB 25 dB 25 dB 25 dB 20 dB 14 dB 25 dB 25 dB 25 dB 25 dB 25 dB 17 dB 10 dB Options as indicated 0.01 dB (all options) Typicals Option 020, 120 Option 025, 125 –30 to +10 dBm –30 to +10 dBm –30 to +10 dBm –30 to +8 dBm –30 to +4 dBm –30 to +2 dBm –90 to +9 dBm –90 to +9 dBm –90 to +9 dBm –90 to +8 dBm –90 to +4 dBm –90 to +1 dBm Option 220 Option 225 Option 420, 520 Option 425, 525 –27 to +12 dBm –27 to +12 dBm –27 to +12 dBm –27 to +12 dBm –27 to +7 dBm –27 to +7 dBm –87 to +12 dBm –87 to +12 dBm –87 to +12 dBm –87 to +12 dBm –87 to +7 dBm –87 to +7 dBm –27 to +9 dBm –27 to +8 dBm –27 to +8 dBm –27 to +8 dBm –27 to +5 dBm –27 to +5 dBm –27 to +1 dBm –27 to –5 dBm –87 to +8 dBm –87 to +8 dBm –87 to +8 dBm –87 to +8 dBm –87 to +4 dBm –87 to +4 dBm –87 to –2 dBm –87 to –9 dBm –33 dBm –93 dBm +20 dBm +20 dBm Typicals Option 020, 025, 120, 125 Phase noise (Nominal power at test port) 10 kHz Offset 100 kHz Offset –30 dBm +20 dBm –90 dBm +20 dBm –30 dBm +20 dBm –90 dBm +20 dBm 300 kHz to 10 MHz 10 MHz to 1.5 GHz 1.5 to 3.125 GHz 3.125 to 6.25 GHz 6.25 to 12.5 GHz 12.5 to 13.5 GHz 13.5 to 20 GHz 20 to 40 GHz 40 to 50 GHz Description –95 dBc/Hz –95 dBc/Hz –95 dBc/Hz –89 dBc/Hz –83 dBc/Hz –77 dBc/Hz Power range 300 kHz to 10 MHz 10 to 45 MHz 45 MHz to 6 GHz 6 to 9 GHz 9 to 12.5 GHz 12.5 to 13.5 GHz 13.5 to 20 GHz 20 to 40 GHz 40 to 50 GHz Power settings Minimum power setting Maximum power setting Description –86 dBc/Hz –86 dBc/Hz –83 dBc/Hz –77 dBc/Hz –71 dBc/Hz –65 dBc/Hz –86 dBc/Hz –91 dBc/Hz –91 dBc/Hz –85 dBc/Hz –79 dBc/Hz –73 dBc/Hz Option 220, 225, 420, 425, 520, 525 1 MHz Offset Typicals Option 020, 025, 120, 125 Non-harmonic spurious (at nominal output power)3 300 kHz to 10 MHz –50 dBc for offset frequency > 1 kHz 10 MHz to 13.5 GHz 13.5 to 20 GHz 20 to 40 GHz –30 dBc for offset frequency > 1 kHz 40 to 50 GHz Description Typicals Option 020, 025, 120, 125 Option 220, 225 Harmonics (2nd or 3rd) at maximum output power 300 kHz to 10 MHz –17 dBc 10 to 500 MHz –17 dBc –22 dBc 500 MHz to 1 GHz –17 dBc –22 dBc 1 to 13.5 GHz –20 dBc –22 dBc 13.5 to 20 GHz –22 dBc 20 to 40 GHz 40 to 50 GHz 10 kHz Offset 100 kHz Offset 1 MHz Offset –77 dBc/Hz –83 dBc/Hz –77 dBc/Hz –71 dBc/Hz –65 dBc/Hz –65 dBc/Hz –59 dBc/Hz –59 dBc/Hz –77 dBc/Hz –91 dBc/Hz –85 dBc/Hz –79 dBc/Hz –73 dBc/Hz –73 dBc/Hz –67 dBc/Hz –67 dBc/Hz –89 dBc/Hz –95 dBc/Hz –89 dBc/Hz –83 dBc/Hz –77 dBc/Hz –77 dBc/Hz –71 dBc/Hz –71 dBc/Hz Option 220, 225, 420, 425, 520, 525 Option 420, 425 Option 520, 525 –15 dBc –15 dBc –20 dBc –20 dBc –22 dBc –15 dBc –15 dBc –20 dBc –20 dBc –22 dBc –22 dBc 1. Performance specified on Port 1 only. Port 2 performance is a characteristic. 2. ALC range starts at maximum leveled power and decreases in power level indicated by the dB amount specified here. 3. Spurious signal levels are valid for a 10 MHz span centered on the carrier frequency. Spurious signals up to -15 dBc may exist outside the span. These signals do not affect the accuracy of the network analyzer measurements. 20 Table 11. Test point input Speciications Option Option Option 020, 025, 120, 125 220, 225 420, 425 Test port noise loor1 10 Hz IF bandwidth2 300 kHz to 3 MHz3 < –83 dBm 3 to 10 MHz < –103 dBm 10 to 45 MHz < –112 dBm 45 to 70 MHz < –112 dBm < –96 dBm < –90 dBm 70 to 500 MHz < –112 dBm < –100 dBm < –90 dBm 500 MHz to 2 GHz < –112 dBm < –105 dBm < –110 dBm 2 to 4 GHz < –112 dBm < –105 dBm < –110 dBm 4 to 8 GHz < –112 dBm < –105 dBm < –110 dBm 8 to 10.5 GHz < –112 dBm < –105 dBm < –100 dBm 10.5 to 13.5 GHz < –107 dBm < –105 dBm < –100 dBm 13.5 to 20 GHz < –105 dBm < –100 dBm 20 to 31.25 GHz < –100 dBm 31.25 to 40 GHz < –95 dBm 40 to 50 GHz Test port noise loor1 1 KHz IF bandwidth 300 kHz to 3 MHz3 < –73 dBm 3 to 10 MHz < –83 dBm 10 to 45 MHz < –92 dBm 45 to 70 MHz < –92 dBm < –76 dBm < –70 dBm 70 to 500 MHz < –92 dBm < –80 dBm < –70 dBm 500 MHz to 2 GHz < –92 dBm < –85 dBm < –90 dBm 2 to 4 GHz < –92 dBm < –85 dBm < –90 dBm 4 to 8 GHz < –92 dBm < –85 dBm < –90 dBm 8 to 10.5 GHz < –92 dBm < –85 dBm < –80 dBm 10.5 to 13.5 GHz < –87 dBm < –85 dBm < –80 dBm 13.5 to 20 GHz < –85 dBm < –80 dBm 20 to 31.25 GHz < –80 dBm 31.25 to 40 GHz < –75 dBm 40 to 50 GHz Description Speciications Option 020, 125 Option 225 Option 425 Direct receiver access input noise loor1 10 Hz IF bandwidth2 300 kHz to 3 MHz3 < –99 dBm 3 to 10 MHz < –119 dBm 10 to 45 MHz < –128 dBm 45 to 70 MHz < –128 dBm < –108 dBm < –111 dBm 70 to 500 MHz < –128 dBm < –112 dBm < –111 dBm 500 MHz to 2 GHz < –128 dBm < –117 dBm < –122 dBm 2 to 8 GHz < –128 dBm < –117 dBm < –122 dBm 8 to 10.5 GHz < –128 dBm < –117 dBm < –112 dBm 10.5 to 13.5 GHz < –128 dBm < –117 dBm < –112 dBm 13.5 to 20 GHz < –117 dBm < –112 dBm 20 to 31.25 GHz < –111 dBm 31.25 to 40 GHz < –106 dBm 40 to 50 GHz Direct receiver access input noise loor1 1 KHz IF bandwidth 300 kHz to 3 MHz3 < –89 dBm 3 to 10 MHz < –99 dBm 10 to 45 MHz < –108 dBm 45 to 70 MHz < –108 dBm < –88 dBm < –91 dBm 70 to 500 MHz < –108 dBm < –92 dBm < –91 dBm 500 MHz to 2 GHz < –108 dBm < –97 dBm < –102 dBm 2 to 8 GHz < –108 dBm < –97 dBm < –102 dBm 8 to 10.5 GHz < –108 dBm < –97 dBm < –92 dBm 10.5 to 13.5 GHz < –108 dBm < –97 dBm < –92 dBm 13.5 to 20 GHz < –97 dBm < –92 dBm 20 to 31.25 GHz < –91 dBm 31.25 to 40 GHz < –86 dBm 40 to 50 GHz Description Option 520, 525 < –90 dBm < –90 dBm < –110 dBm < –110 dBm < –110 dBm < –100 dBm < –100 dBm < –100 dBm < –100 dBm < –95 dBm < –90 dBm < –70 dBm < –70 dBm < –90 dBm < –90 dBm < –90 dBm < –80 dBm < –80 dBm < –80 dBm < –80 dBm < –75 dBm < –70 dBm Option 525 Typicals Option 020, 025, 120, 125 < –94 dBm < –110 dBm < –116 dBm < –116 dBm < –116 dBm < –120 dBm < –120 dBm < –119 dBm < –119 dBm < –114 dBm < –83 dBm < –90 dBm < –96 dBm < –96 dBm < –96 dBm < –100 dBm < –100 dBm < –99 dBm < –99 dBm < –94 dBm Typicals Option 020, 125 Option 220, 225 Option 420, 425 Option 520, 525 < –89 dBm < –80 dBm < –80 dBm < –69 dBm < –60 dBm < –60 dBm Option 225 Option 425 Option 525 < –120 dBm < –126 dBm < –126 dBm < –111 dBm < –111 dBm < –122 dBm < –122 dBm < –112 dBm < –112 dBm < –112 dBm < –111 dBm < –106 dBm < –98 dBm < –100 dBm < –106 dBm < –106 dBm < –91 dBm < –91 dBm < –102 dBm < –102 dBm < –92 dBm < –92 dBm < –92 dBm < –91 dBm < –86 dBm < –78 dBm 1. Total average (rms) noise power calculated as the mean value of a linear magnitude trace expressed in dBm. 2. 10 Hz IFBW test port noise floor performance is mathematically derived from the 1 kHz IFBW noise floor performance. The performance could be limited by crosstalk below 3 MHz at certain frequencies. The measurement is defined as a single receiver measurement with loads on the ports at a given CW frequency with power set to the minimum plus 5 dB. 3. Value and/or frequency changed July 2006. 21 Table 11. Test port input (Continued) Description Speciications Option 220, 225 Option 420, 520 Typicals Option 220, 225 Option 425, 525 Compression level 10 to 45 MHz2 45 to 500 MHz 500 MHz to 2 GHz 2 to 8 GHz 8 to 12.5 GHz 12.5 to 20 GHz 20 to 31.25 GHz 31.25 to 40 GHz 40 to 50 GHz Description Power Compression Power Compression Power Compression +5 dBm +5 dBm +5 dBm +5 dBm +3 dBm 0.10 dB 0.15 dB 0.21 dB 0.21 dB 0.20 dB +5 dBm +5 dBm +5 dBm +5 dBm +5 dBm 0 dBm –3 dBm –3 dBm 0.40 dB 0.77 dB 0.75 dB 0.56 dB 0.79 dB 0.60 dB 0.55 dB 0.66 dB +5 dBm +5 dBm +5 dBm +5 dBm +5 dBm 0 dBm –3 dBm –3 dBm 0.40 dB 0.67 dB 0.55 dB 0.51 dB 0.69 dB 0.50 dB 0.60 dB 0.71 dB Speciications Option 020, 120, 025, 125 Typicals Compression level Power +5 dBm Typicals Option 020, 120, 025, 125 Description Compression level – 0.1 dB 300 kHz to 10 MHz 10 to 50 MHz 50 MHz to 1 GHz 1 to 6 GHz 6 to 8 GHz 8 to 12.5 GHz 12.5 to 13.5 GHz Power +8 dBm +8 dBm +8 dBm +8 dBm +8 dBm +8 dBm +8 dBm Description Speciications Option 220, 225 Compression 1.0 dB 0.1 dB at +5 dBm 0.35 dB 0.35 dB 0.25 dB 0.25 dB 0.30 dB 0.40 dB 300 kHz to 10 MHz 10 MHz to 1 GHz 1 to 12.5 GHz 12.5 to 13.5 GHz Power +5 dBm +9 dBm +10 dBm +9 dBm Compression 0.1 dB 0.1 dB 0.1 dB 0.1 dB Typicals Option 420, 425 Option 520, 525 – – – – – – – – – – – – – – – – – – – – Option 220 Option 225 Option 420, 425 Option 520, 525 +10 dBm +10 dBm +9 dBm +6 dBm +6 dBm +6 dBm Negligible +10 dBm +9 dBm +6 dBm +6 dBm +6 dBm Negligible 0.0 dBm 0.0 dBm 0.0 dBm –1.0 dBm –1.0 dBm –5.5 dBm –8.5 dBm Negligible +1.0 dBm +1.0 dBm +1.5 dBm 0.0 dBm 0.0 dBm –3.0 dBm –7.5 dBm –10.0 dBm 0.004 dB rms 0.015 dB rms 0.015 dB rms Test port compression - 0.1 dB 300 kHz to 10 MHz 10 to 45 MHz2 45 to 500 MHz 500 MHz to 2 GHz 2 to 12.5 GHz 12.5 to 13.5 GHz 13.5 to 20 GHz 20 to 31.25 GHz 31.25 to 40 GHz 40 to 50 GHz – – – – – – – – – – Trace noise magnitude3 1 kHz IF bandwidth, ratioed measurement, nominal power at test port. 300 kHz to 10 MHz 10 to 45 MHz 45 to 500 MHz 500 MHz to 2 GHz 2 to 10.5 GHz 10.5 to 13.5 GHz 13.5 to 20 GHz 20 to 31.25 GHz 31.25 to 40 GHz 40 to 50 GHz – – – 0.004 dB rms 0.004 dB rms 0.004 dB rms 0.006 dB rms 0.006 dB rms 0.010 dB rms 0.006 dB rms 0.006 dB rms 0.010 dB rms 0.010 dB rms 0.010 dB rms 0.020 dB rms 0.010 dB rms 0.006 dB rms 0.006 dB rms 0.010 dB rms 0.010 dB rms 0.010 dB rms 0.020 dB rms 0.020 dB rms 1. Total average (rms) noise power calculated as the mean value of a linear magnitude trace expressed in dBm. 2. For Options 225, 420, 425, 520, and 525 coupler roll-off will reduce compression to a negligible level below 45 MHz. 3. 1 kHz IF BW, ratioed measurement, nominal power at the test port. 22 Compression 0.10 dB Table 11. Test port input (Continued) Description Speciications Typicals Option 020, 120, 025, 125 Option 020, 120, 025, 125 magnitude3 Trace noise (continued) 100 kHz IF bandwidth, ratioed measurement, nominal power at test port. 300 kHz to 10 MHz 10 MHz to 6 GHz 6 to 10.5 GHz 10.5 to 13.5 GHz 12 mdB 4 mdB 4 mdB 8 mdB 600 kHz IF bandwidth, ratioed measurement, nominal power at test port. 300 kHz to 10 MHz 10 MHz to 6 GHz 6 to 10.5 GHz 10.5 to 13.5 GHz – – – – 20 mdB 8 mdB 8 mdB 10 mdB Speciications Description Option 220, 225 Typicals Option 420, 425 Option 520, 525 Option 220, 225 Option 420, 425 Option 520, 525 0.025° rms 0.100° rms 0.100° rms Trace noise phase3 1 kHz IF bandwidth, ratioed measurement, nominal power at test port. 300 kHz to 10 MHz 10 to 45 MHz 45 to 500 MHz 500 MHz to 2 GHz 2 to 10.5 GHz 10.5 to 13.5 GHz 13.5 to 20 GHz 20 to 31.25 GHz 31.25 to 40 GHz 40 to 50 GHz – – – 0.060° rms 0.060° rms 0.060° rms 0.060° rms 0.060° rms 0.100° rms 0.060° rms 0.060° rms 0.100° rms 0.100° rms 0.100° rms 0.200° rms 0.100° rms 0.060° rms 0.060° rms 0.100° rms 0.100° rms 0.100° rms 0.200° rms 0.200° rms Description Speciications Typicals Option 020, 120, 025, 125 Option 020, 120, 025, 125 Trace noise phase3 100 kHz IF bandwidth, ratioed measurement, nominal power at test port. 300 kHz to 10 MHz 10 MHz to 6 GHz 6 to 10.5 GHz 10.5 to 13.5 GHz 80 mdeg 30 mdeg 30 mdeg 60 mdeg 600 kHz IF bandwidth, ratioed measurement, nominal power at test port. 300 kHz to 10 MHz 10 MHz to 6 GHz 6 to 10.5 GHz 10.5 to 13.5 GHz – – – – Description Speciications 100 mdeg 60 mdeg 60 mdeg 80 mdeg Option 020, 025, 120, 125, 220, 225, 420, 425, 520, 525 Reference level magnitude Range Resolution Typicals Option 020, 025, 120, 125, 220, 225, 420, 425, 520, 525 ±200 dB 0.001 dB Reference level phase Range Resolution ±500° 0.01° 1. Total average (rms) noise power calculated as the mean value of a linear magnitude trace expressed in dBm. 2. For Options 225, 420, 425, 520, and 525 coupler roll-off will reduce compression to a negligible level below 45 MHz. 3. 1 kHz IF BW, ratioed measurement, nominal power at the test port. 4. Stability is defined as a ratio measurement made at the test port. 23 Table 11. Test port input (Continued) Description Stability magnitude4 300 kHz to 10 MHz 10 to 45 MHz 45 to 500 MHz 500 MHz to 2 GHz 2 to 4 GHz 4 to 8 GHz 8 to 13.5 GHz 13.5 to 20 GHz 20 to 40 GHz 40 to 50 GHz Stability phase4 300 kHz to 10 MHz 10 to 45 MHz 45 to 500 MHz 500 MHz to 2 GHz 2 to 4 GHz 4 to 8 GHz 8 to 13.5 GHz 13.5 to 20 GHz 20 to 40 GHz 40 to 50 GHz Description Damage input level Test port 1 and 2 Typicals Option 020, 025, 120, 125 Option 220, 225 Option 420, 425, 520, 525 ±0.015 dB/°C ±0.010 dB/°C ±0.010 dB/°C ±0.020 dB/°C ±0.020 dB/°C ±0.030 dB/°C ±0.030 dB/°C ±0.015 dB/°C ±0.010 dB/°C ±0.010 dB/°C ±0.010 dB/°C ±0.010 dB/°C ±0.015 dB/°C ±0.015 dB/°C ±0.040 dB/°C ±0.060 dB/°C ±0.25°/°C ±0.20°/°C ±0.15°/°C ±0.15°/°C ±0.15°/°C ±0.45°/°C ±0.45°/°C ±0.25°/°C ±0.22°/°C ±0.22°/°C ±0.10°/°C ±0.10°/°C ±0.15°/°C ±0.15°/°C ±0.40°/°C ±0.40°/°C Typicals Option 020, 120 Option 220 Option 420, 520 Option 025, 125 Option 225, 425, 525 +27 dBm or ±16 VDC +30 dBm or ±25 VDC +30 dBm or ±40 VDC +27 dBm or ±16 VDC +15 dBm or ±16 VDC +15 dBm or ±16 VDC +27 dBm or ±16 VDC +15 dBm or ±0 VDC +20 dBm or ±16 VDC +27 dBm or ±16 VDC +27 dBm or ±7 VDC +15 dBm or ±7 VDC +15 dBm or ±7 VDC +30 dBm or ±40 VDC +30 dBm or ±7 VDC +20 dBm or ±7 VDC +30 dBm or ±7 VDC ±0.015 dB/°C ±0.010 dB/°C ±0.010 dB/°C ±0.010 dB/°C ±0.015 dB/°C ±0.020 dB/°C ±0.020 dB/°C ±0.30°/°C ±0.025°/°C ±0.035°/°C ±0.050°/°C ±0.10°/°C ±0.15°/°C ±0.30°/°C R1, R2 in A, B in Coupler thru Coupler arm Source out (reference) Source out (test ports) 1. Total average (rms) noise power calculated as the mean value of a linear magnitude trace expressed in dBm. 2. For Options 225, 420, 425, 520, and 525 coupler roll-off will reduce compression to a negligible level below 45 MHz. 3. 1 kHz IF BW, ratioed measurement, nominal power at the test port. 4. Stability is defined as a ratio measurement made at the test port. 24 Dynamic Accuracy Note: Dynamic accuracy uncertainty curves are available within the PNA-L network analyzer’s internal Help system. The Help system is also available online at www.keysight.com. Navigate to the home page for your PNA model, then click on manuals & guides. Please download our free uncertainty calculator from www.keysight.com/find/na_calculator to generate the curves for your calibration kit and PNA setup. Table 12. Test port input (group delay)1 Description Supplemental information (typ.) Aperture (selectable) (frequency span)/(number of points –1) Maximum aperture 20% of frequency span Range 0.5 x (1/minimum aperture) Maximum delay Limited to measuring no more than 180° of phase change within the minimum aperture Accuracy See graph below. (Char.) Accuracy (nsec) Group delay (typical) Aperture (MHz) The following graph shows characteristic group delay accuracy with full 2-port calibration and a 10 Hz IF bandwidth. Insertion loss is assumed to be < 2 dB and electrical length to be ten meters. In general, the following formula can be used to determine the accuracy, in seconds, of specific group delay measurement: ± Phase Accuracy (deg)/[360° Aperture (Hz)] Depending on the aperture and device length, the phase accuracy used is either incremental phase accuracy or worst case phase accuracy. 1. Group delay is computed by measuring the phase change within a specified frequency step (determined by the frequency span and the number of points per sweep). 25 General Information Table 13. Miscellaneous information Description Supplemental information System IF bandwidth range Option 020, 025, 120, 125 Option 220, 225, 420, 425, 520, 525 CPU Intel 1.1 GHz Pentium M with 1 GByte RAM 1 Hz to 600 kHz, nominal 1 Hz to 250 kHz, nominal Table 14. Front panel information Description Supplemental information RF connectors N5230C Type Option 020, 025, 120, 125, 220 or 225: 3.5 mm (male), 50 ohm, (nominal) Option 420, 425, 520, or 525: 2.4 mm (male), 50 ohm, (nominal) Center pin recession 0.002 in. (characteristic) Display Size 21.3 cm (8.4 in) diagonal color active matrix LCD; 1024 (horizontal) X 768 (vertical) resolution Refresh rate 60 Hz Display range The PNA display must remain in the 16-bit color setting in order to comply with international emissions regulations Magnitude ± 500 dB (at 20 dB/div), max Phase ± 500°, max Polar 10 pUnits, min 1000 Units, max Display resolution Magnitude 0.001 dB/div, min Phase 0.01°/div, min Marker resolution 26 Magnitude 0.001 dB, min Phase 0.01°, min Polar 0.01 mUnit, min; 0.01°, min Table 15. Rear panel information Description Supplemental information Trigger inputs/outputs BNC (f), TTL/CMOS compatible 10 MHz Reference in Connector BNC, female Input frequency 10 MHz ± 10 ppm, typical Input level –15 to +20 dBm, typical Input impedance 200 Ω, nom. 10 MHz Reference out Connector BNC, female Output frequency 10 MHz ± 1 ppm, typical Signal type Sine Wave, typical Output level +10 dBm ± 4 dB into 50 W, typical Output impedance 50 Ω, nominal Harmonics < –40 dBc, typical VGA Video output Connector 15-pin mini D-Sub; Drives VGA compatible monitors Test set IO 25-pin D-Sub connector, available for external test set control Aux IO 25-pin D-Sub connector, male, analog and digital I/O Handler IO 36-pin parallel I/O port; all input/output signals are default set to negative logic; can be reset to positive logic via GPIB command GPIB Two ports: dedicated Controller and dedicated Talker/Listener. 24-pin D-sub (Type D-24), female; compatible with IEEE-488. USB Port 2 ports on front panel and 4 ports on rear panel. LAN 10/100BaseT Ethernet, 8-pin configuration; auto selects between the two data rates Line power (single phase) Frequency, voltage 50/60 Hz/400 Hz for 100 to 120 V, 50/60 Hz for 220 to 240 V, (power supply is auto switching) Maximum 350 Watts 27 Table 16. Analyzer environment and dimensions Description Supplemental information General environmental EMC Complies with European EMC directive 2004/108/EC – IEC/EN 61326-1:2005 – CISPR Pub 11 Group 1, class A – AS/NZS CISPR II:2004 – ICES/NMB-001 Safety Complies with European Low Voltage Directive 2006/95/EC – IEC/EN 61010-1:2001 – Canada: CSA C22.2 No. 61010-1:2004 – USA: UL 61010-1:2004 Operating environment Temperature 0 to +40 °C Instrument powers up and displays no error messages within this temperature range (except for "source unleveled" error message that may occur at temperatures outside the specified performance temperature range of 25 ± 5 °C). Error-corrected temperature range 23 °C ± 3 °C with less than 1 °C deviation from calibration temp. Relative humidity Type-tested 0 to 95% at 40 °C, non-condensing Altitude 0 to 4600 m (15,000 ft.) Non-operating storage environment Temperature –40 to +70 °C Cabinet dimensions Height Width Depth Excluding front and rear panel hardware and feet 267 mm 10.5 in 426 mm 16.75 427 mm 16.8 in As shipped - includes front panel connectors, rear panel bumpers, and feet. 280 mm 11 in 435 mm 17.10 in 470 mm 18.5 in As shipped plus handles 280 mm 11 in 458 mm 18 in 501 mm 19.7 in As shipped plus rack-mount flanges 280 mm 11 in 483 mm 19 in 470 mm 18.5 in As shipped plus handles and rack-mount flanges 280 mm 11 in 483 mm 19 in 501 mm 19.7 in Weight Net N5230C 24.9 kg (55 lb), nominal Shipping N5230C 28 36.3 kg (80 lb), nominal Measurement Throughput Summary Table 17. Typical cycle time1,2 (ms) for measurement completion Number of Points 201 401 801 1601 16,001 Uncorrected 97.5 102.7 103.8 108.2 683.9 2-Port cal 203.7 213.5 218.5 234.6 1504.3 Uncorrected 112.6 120.6 124.8 138.2 738.4 2-Port cal 232.8 251.8 265.2 304.3 1623.4 Start 8 GHz, stop 18 GHz, 30 kHz IF bandwidth Start 10 MHz, stop 10 GHz, 30 kHz IF bandwidth Start 10 MHz, stop 20 GHz, 30 kHz IF bandwidth Uncorrected 146 199.3 210.9 217.2 753.9 2-Port cal 302.3 410.5 438.7 462.5 1660.5 Uncorrected 79.1 81 81.7 86.6 482 2-Port cal 164.5 170.3 175.3 193.5 1104.7 Uncorrected 96.8 101.7 108.8 122.2 524.6 2-Port cal 202.1 215.6 236.7 276.7 1198.8 Uncorrected 141.6 163.9 170.7 179.7 546.5 2-Port cal 293.6 341 360 389.5 1248.8 Start 8 GHz, stop 18 GHz, 50 kHz IF bandwidth Start 10 MHz, stop 10 GHz, 50 kHz IF bandwidth Start 10 MHz, stop 20 GHz, 50 kHz IF bandwidth 1. Typical performance. 2. Includes sweep time, retrace time and band-crossing time. Analyzer display turned off with DISPLAY:ENABLE OFF. Add 21 ms for display on. Data for one trace (S11) measurement. 29 Table 18. Cycle Time vs IF bandwidth1 (Options 020, 025, 120, 125 only) Applies to the preset condition (201 points, correction off) except for the following changes: – CF = 10 GHz – Span = 100 MHz – Display off (add 21 ms for display on) Description Typical performance IF Bandwidth (Hz) Cycle time (ms)2 Trace noise (dB rms) 600,000 7 0.0035 360,000 7 0.0026 280,000 7 0.0022 200,000 7 0.0021 150,000 7 0.0016 100,000 7 0.0012 70,000 7 0.0011 50,000 9 0.0009 30,000 11 0.0008 20,000 14 0.0006 15,000 17 0.0005 10,000 28 0.0004 7,000 37 0.0004 5,000 48 0.0003 3,000 72 0.0003 2,000 102 0.0002 1,500 130 0.0001 1,000 218 0.0001 700 294 0.0001 500 399 0.0001 300 636 0.0001 200 932 Negligible 100 1,826 Negligible 30 6,004 Negligible 10 17,903 Negligible 1 178,398 Negligible 1. Typical performance. 2. Cycle time includes sweep and retrace time. 30 Table 19. Cycle Time vs IF bandwidth1 (Options 220, 225, 420, 425, 520, 525 only) Applies to the preset condition (201 points, correction off) except for the following changes: – CF = 10 GHz – Span = 100 MHz – Display off (add 21 ms for display on) Description Typical performance IF Bandwidth (Hz) Cycle time (ms)2 Cycle time (ms) Option 080 enabled 250,000 8 37 200,000 9 39 150,000 9 40 100,000 10 41 70,000 11 43 50,000 12 45 30,000 15 50 20,000 18 53 15,000 21 57 10,000 27 65 7,000 34 75 5,000 48 93 3,000 72 124 2,000 108 169 1,500 126 187 1,000 272 700 357 500 460 300 697 200 1003 150 1307 100 1917 30 6173 10 18214 1 181699 1. Typical performance. 2. Cycle time includes sweep and retrace time. 31 Table 20. Cycle time vs number of points1 (Options 020, 025, 120, 125 only) Applies to the preset condition (201 points, correction off) except for the following changes: – CF = 10 GHz – Span = 100 MHz – Display off (add 21 ms for display on) Description Typical performance IF Bandwidth (Hz) Number of points Cycle time (ms)2 30,000 3 6 11 7 300,000 600,000 51 6 101 7 201 11 401 18 801 32 1,601 59 6,401 224 16,001 556 3 6 11 6 51 6 101 7 201 7 401 9 801 13 1,601 22 6,401 75 16,0001 180 3 6 11 6 51 6 101 6 201 7 401 8 801 9 1,601 12 6,401 27 16,0001 59 1. Typical performance. 2. Cycle time includes sweep and retrace time. 32 Table 21. Cycle time vs number of points1 (Options 220, 225, 420, 425, 520, 525 only) Applies to the preset condition (correction off) except for the following changes: – CF = 10 GHz – Span = 100 MHz – Display off (add 21 ms for display on) IF Bandwidth (Hz) 30,000 50,000 250,000 Number of points Cycle time (ms)2 3 8 11 8 51 9 101 11 201 15 401 23 801 39 1,601 71 6,401 265 16,001 650 3 7 11 7 51 8 101 10 201 13 401 18 801 29 1,601 52 6,401 184 16,001 448 101 8 201 9 401 10 801 14 1,601 21 6,401 61 16,001 147 1. Typical performance. 2. Cycle time includes sweep and retrace time. Note: Specifications for recall and sweep speed are not provided for the N5230C analyzers. 33 Table 22. Data transfer time (ms)1 Number of points 201 401 1601 16,001 SCPI over GPIB (program executed on external PC) 32-bit floating point 7 12 43 435 64-bit floating point 12 22 84 856 ASCII 64 124 489 5054 SCPI (program executed in the analyzer) 32-bit floating point 1 2 3 30 64-bit floating point 2 2 4 40 ASCII 29 56 222 2220 COM (program executed in the analyzer) 32-bit floating point < 0.4 0.4 0.5 1.9 Variant type 0.7 1 3 32 DCOM over LAN (program executed on external PC) 32-bit floating point < 0.8 1 1.5 7.1 Variant type 1.8 2.7 8.5 80 1. Typical performance. Note: Specifications for recall and sweep speed are not provided for the N5230C analyzers. 34 Speciications: Front-Panel Jumpers Model N5230C Option 025, 125, 225, 425, or 525 Note: The N5230C Option 020, 120, 220, 420, or 520 (standard test set and standard power range) has no front-panel jumpers. Table 23. Measurement receiver inputs (rcvr A In, rcvr B In) 0-1 dB Typical Compression Typicals Description Option 025, 125 Option 225 Options 425, 525 Maximum input level 300 kHz to 10 MHz –11 dBm 10 to 45 MHz –7 dBm –2 dBm –20 dBm 45 to 500 MHz –7 dBm –2 dBm –19 dBm 500 MHz to 2 GHz –6 dBm –3 dBm –14 dBm 2 to 12.5 GHz –6 dBm –6 dBm –14 dBm 12.5 to 13.5 GHz –7 dBm –6 dBm –15 dBm –6 dBm –15 dBm 13.5 to 20 GHz 20 to 31.25 GHz –16 dBm 31.25 to 40 GHz –21 dBm 40 to 45 GHz –24 dBm 45 to 50 GHz –22 dBm Damage level N5230C +15 dBm +15 dBm +15 dBm ±16 V ±7 V ±7 V Maximum DC level N5230C 35 Table 24. Reference receiver inputs (rcvr R1, rcvr R2) at maximum specified output power Typicals Description Option 025, 125 Option 225 Options 425, 525 Maximum input level 300 kHz to 10 MHz –15 dBm 10 to 500 MHz –13 dBm –18 dBm –28 dBm 500 to 2 MHz –14 dBm –18 dBm –28 dBm 2 to 6 GHz –14 dBm –19 dBm –28 dBm 6 to 8 GHz –16 dBm –19 dBm –28 dBm 8 to 9 GHz –16 dBm –21 dBm –27 dBm 9 to 10.5 GHz –20 dBm –21 dBm –27 dBm 10.5 to 12.5 GHz –22 dBm –21 dBm –27 dBm 12.5 to 13.5 GHz –24 dBm –23 dBm –26 dBm –23 dBm –26 dBm 13.5 to 20 GHz 20 to 31.25 GHz –33 dBm 31.25 to 40 GHz –27 dBm 40 to 45 GHz –29 dBm 45 to 50 GHz –28 dBm Damage level N5230C +15 dBm +15 dBm +15 dBm ±16 V ±7 V ±7 V Maximum DC level N5230C Table 25. Reference Outputs (reference 1 source out, reference 2 source out) at maximum specified output power Typicals Description Option 025, 125 Option 225 Options 425, 525 –18 dBm –28 dBm Maximum output level 300 kHz to 10 MHz –15 dBm 10 to 500 MHz –13 dBm 500 MHz to 2 GHz –14 dBm –18 dBm –28 dBm 2 to 6 GHz –14 dBm –19 dBm –28 dBm 6 to 8 GHz –16 dBm –19 dBm –28 dBm 8 to 9 GHz –16 dBm –20 dBm –27 dBm 9 to 10.5 GHz –20 dBm –20 dBm –27 dBm 10.5 to 12.5 GHz –22 dBm –20 dBm –27 dBm 12.5 to 13.5 GHz –24 dBm –23 dBm –26 dBm 13.5 to 20 GHz –23 dBm –26 dBm 20 to 31.25 GHz –32 dBm 31.25 to 40 GHz –26 dBm 40 to 45 GHz –29 dBm 45 to 50 GHz –28 dBm Damage level N5230C +20 dBm +20 dBm +20 dBm ±16 V ±7 V ±7 V Maximum DC level N5230C 36 Table 26. Source outputs (port 1 source out, port 2 source out)at maximum specified output power Typicals Description Option 025, 125 Option 225 Options 425, 525 +6 dBm +1 dBm Maximum output level 300 kHz to 10 MHz +11 dBm 10 to 500 MHz +11 dBm 500 MHz to 6 GHz +11 dBm +7 dBm +1 dBm 6 to 9 GHz +10 dBm +7 dBm +1 dBm 9 to 12.5 GHz +8 dBm +7 dBm +1 dBm 12.5 to 13.5 GHz +5 dBm +5 dBm +3 dBm +5 dBm +3 dBm 13.5 to 20 GHz 20 to 31.25 GHz –5 dBm 31.25 to 40 GHz –4 dBm 40 to 45 GHz –11 dBm 45 to 50 GHz –11 dBm Damage level N5230C +27 dBm +30 dBm +30 dBm ±16 V ±7 V ±7 V Maximum DC level N5230C Table 27. Coupler inputs (port 1 Cplr Thru, port 2 Cplr Thru) Typicals Description Option 025, 125 Option 225 Options 425, 525 Insertion loss to test port 30 kHz to 10 MHz 2 dB 10 to 500 MHz 2 dB 0.6 dB 0.6 dB 500 MHz to 2 GHz 3 dB 1.6 dB 0.8 dB 2 to 8 GHz 3 dB 1.8 dB 1.0 dB 8 to 9 GHz 3 dB 1.9 dB 1.0 dB 9 to 12.5 GHz 4 dB 1.9 dB 1.0 dB 12.5 to 13.5 GHz 4 dB 2.0 dB 2.0 dB 2.0 dB 2.0 dB 13.5 to 20 GHz 20 to 31.25 GHz 3.0 dB 31.25 to 50 GHz 4.0 dB Damage level N5230C +27 dBm +30 dBm +30 dBm ±16 V ±40 V ±40 V Maximum DC level N5230C Table 28. Coupler outputs (port 1 Cplr Arm, port 2 Cplr Arm) Typicals Description Option 025, 125 Option 225 Options 425, 525 +15 dBm +30 dBm +30 dBm +0 Vdc +7 Vdc +7 Vdc Damage level N5230C Maximum DC level N5230C 37 Test Set Block Diagrams N5230C Option 020, 120, 220, 420, or 520 (standard test set and standard power range) network analyzer R1 R2 A B Port 1 Port 2 N5230C Option 025, 125, 225, 425, or 525 (configurable test set and extended power range) network analyzer R1 R2 A Source Rcvr SRC Cplr out R1 out thru in 38 Port 1 Cplr Rcvr arm A in B Rcvr Cplr Port 2 B arm in Cplr SRC Rcvr Source thru out R2 out in 39 | Keysight | 2-Port PNA-L Microwave Network Analyzer, N5230C 300 kHz to 6, 13.5 GHz, 10 MHz to 20, 40, 50 GHz – Data Sheet myKeysight www.keysight.com/find/mykeysight A personalized view into the information most relevant to you. www.keysight.com/find/ThreeYearWarranty Keysight’s commitment to superior product quality and lower total cost of ownership. The only test and measurement company with three-year warranty standard on all instruments, worldwide. Keysight Assurance Plans www.keysight.com/find/AssurancePlans Up to five years of protection and no budgetary surprises to ensure your instruments are operating to specification so you can rely on accurate measurements. www.keysight.com/quality Keysight Electronic Measurement Group DEKRA Certified ISO 9001:2008 Quality Management System Keysight Channel Partners www.keysight.com/find/channelpartners Get the best of both worlds: Keysight’s measurement expertise and product breadth, combined with channel partner convenience. www.keysight.com/find/pnal Web Resources Visit our Web sites for additional product information and literature. PNA Microwave network analyzers: www.keysight.com/find/pna PNA-L network analyzers: www.keysight.com/find/pnal Electronic calibration (ECal): www.keysight.com/find/ecal For more information on Keysight Technologies’ products, applications or services, please contact your local Keysight office. The complete list is available at: www.keysight.com/find/contactus Americas Canada Brazil Mexico United States (877) 894 4414 55 11 3351 7010 001 800 254 2440 (800) 829 4444 Asia Paciic Australia China Hong Kong India Japan Korea Malaysia Singapore Taiwan Other AP Countries 1 800 629 485 800 810 0189 800 938 693 1 800 112 929 0120 (421) 345 080 769 0800 1 800 888 848 1 800 375 8100 0800 047 866 (65) 6375 8100 Europe & Middle East Austria Belgium Finland France Germany Ireland Israel Italy Luxembourg Netherlands Russia Spain Sweden Switzerland United Kingdom 0800 001122 0800 58580 0800 523252 0805 980333 0800 6270999 1800 832700 1 809 343051 800 599100 +32 800 58580 0800 0233200 8800 5009286 0800 000154 0200 882255 0800 805353 Opt. 1 (DE) Opt. 2 (FR) Opt. 3 (IT) 0800 0260637 For other unlisted countries: www.keysight.com/find/contactus (BP-06-09-14) Test and measurement solutions: www.keysight.com/find/accessories This information is subject to change without notice. © Keysight Technologies 2008 - 2014 Published in USA, July 31, 2014 5989-7607EN www.keysight.com
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Page Count : 39 XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:4be67e42-13c3-11e4-0000-7fc1dcf9f66d Producer : GPL Ghostscript 9.07 Modify Date : 2014:07:22 00:17:03-06:00 Create Date : 2014:07:22 00:17:03-06:00 Creator Tool : Adobe InDesign CS6 (Macintosh) Document ID : uuid:4be67e42-13c3-11e4-0000-7fc1dcf9f66d Format : application/pdf Title : Untitled Creator : Adobe InDesign CS6 (Macintosh)EXIF Metadata provided by EXIF.tools