Akurate Manual Loudspeaker System Linn 212 Owners

User Manual: AKURATE Loudspeaker System

Open the PDF directly: View PDF PDF.
Page Count: 19

English
Français
Deutsch
Italiano
Español
Nederlands
AKURATE Loudspeaker System
Owner’s Manual
Important Safety Information English
Important Safety Information
Explanation of symbols used in this manual and on the product:
This symbol is intended to alert the user to the presence of uninsulated
dangerous voltages within the enclosure of sufficient magnitude to cause
electric shock.
This symbol is intended to alert the user to the presence of important operation,
maintenance and servicing information in the instruction and service manuals.
CAUTION
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE THE COVER.
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
REPLACE THE MAINS FUSE IN THE PLUG WITH ONE OF THE SAME TYPE AND RATING.
DISCONNECT SUPPLY CORD BEFORE CHANGING FUSE.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
THIS APPLIANCE SHOULD BE CONNECTED TO A MAINS SOCKET WITH A
PROTECTIVE EARTH CONNECTION
SHOCK HAZARD. DO NOT OPEN.
MAINS PLUGS
This appliance is supplied with a non-rewireable mains plug for the intended country.
Replacement mains leads can be obtained from your Linn retailer. Should you need to
change the plug please dispose of it carefully. A plug with bared conductors is
dangerous if engaged in a live socket.
The Brown wire must be connected to the Live (Line) supply pin.
The Blue wire must be connected to the Neutral supply pin.
The Green/Yellow wire must be connected to the Earth (Ground) supply pin.
Please contact your retailer or a competent electrician if you are in any doubt.
GENERAL SAFETY INSTRUCTIONS
1. Read instructions. Read the safety and operating instructions before operating the appliance.
2. Retain instructions. Retain the safety and operating instructions for future reference.
3. Heed warnings.Observe all warnings on the appliance and in the operating instructions.
4. Follow instructions. Follow all operating and use instructions.
5. Water and moisture. Do not use the appliance near water, for example near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a swimming pool and the like.
6. Carts and stands. Use only with a cart or stand that is recommended by the manufacturer.
6a. An appliance and cart combination should be used with care. Quick stops, excessive force, and uneven
surfaces may cause the appliance and cart combination to overturn.
7. Wall or ceiling mounting. Mount to a wall or ceiling only as recommended by the manufacturer.
8. Ventilation. Site the appliance so that its location or position does not interfere with its proper ventilation.
For example, the appliance should not be situated on a bed, sofa, rug, or similar surface that may block the
ventilation openings, or placed in a built-in installation such as a bookcase or cabinet that may impede the
flow of air through the ventilation openings.
9. Heat. Site the appliance away from heat sources such as radiators, heaters, stoves, or other appliances
(including amplifiers) that produce heat.
10. Power sources. Connect the appliance to a power supply only of the type described in the operating
instructions or marked on the appliance.
11. Grounding or polarisation. Do not defeat the safety purpose of the polarised or grounding type plug. A
polarised plug has two blades with one wider than the other. A grounding type plug has two blades and a
third grounding prong. The wide blade or the third prong is provided for your safety. When the provided plug
does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
12. Power cord protection. Route power cords so that they are not likely to be walked on or pinched by items
placed upon or against them, paying particular attention to cords at plugs, power sockets, and at the point
where they exit from the appliance.
13.Mains plug. Use the mains plug to disconnect the product from the mains supply. The mains plug must be
accessible at all times. Use the mains switch (if applicable) when the product is not in use.
14.Cleaning. The product should be cleaned only as recommended by the manufacturer.
15. Power lines. An outdoor antenna should be located away from power lines.
16. Outdoor antenna grounding. If an outdoor antenna is connected to the tuner/receiver, ensure that the
antenna system is grounded to provide some protection against voltage surges and static build up. In the
USA see article 810 of the National Electrical Code ANSI/NFPA 70 concerning installation requirements.
17. Lightning storms. Unplug this apparatus during lightning storms or when unused for long periods of time.
18. Objects and liquid entry. Do not let objects or liquids fall into the product. Do not expose the product to
dripping or splashing. Do not place a vessel containing liquid on top of the product.
19. Damage requiring service. The product should be serviced by qualified personnel if:
a) The power cord or plug has been damaged.
b) Objects or liquid have fallen into the product.
c) The product has been exposed to rain.
d) The product does not appear to operate normally or exhibits a marked change in operation.
e) The product has been dropped or the enclosure damaged.
20. Servicing. Do not attempt to service the product beyond that described in the operating instructions. All
other servicing should be referred to qualified service personnel.
i
AKURATE Loudspeaker System
Owner’s Manual
UK USERS PLEASE READ THIS
IMPORTANT SAFETY INFORMATION
Fuse replacement
This appliance is fitted with a non-rewireable 13 Amp mains plug. The plug contains a
5 Amp fuse. If the fuse has blown it can be replaced as follows:
a) Pull out the red fuse cover/carrier.
b) Remove and dispose of the blown fuse.
c) Fit a new 5 Amp BS1362 approved fuse into the carrier and push the carrier
back into the plug.
Always ensure the fuse cover is fitted. If the fuse cover is missing do not use the plug.
Contact your Linn retailer to obtain a replacement fuse cover.
Fuses are for fire protection and do not protect against electric shock.
Mains plug replacement
Should your mains plug need replacing and you are competent to do this proceed as
follows. If you are in doubt contact your Linn retailer or a competent electrician.
a) Disconnect the plug from the mains supply.
b) Cut off the plug and dispose of it safely. A plug with bared conductors is
dangerous if engaged in a live socket.
c) Only fit a 13 Amp BS1363A approved plug with a 5 Amp fuse.
d) The cable wire colours or a letter will be marked at the connection points of most
quality plugs.
Attach the wires securely to their respective points. The Brown wire must go to the Live
pin, the Blue wire must go to the Neutral pin, and the Green/Yellow wire must go to the
Earth pin.
e) Before replacing the plug top ensure that the cable restraint is holding the outer
sheath of the cable firmly and that the wires are correctly connected.
WARNING
THIS APPLIANCE MUST BE EARTHED.
CE Declaration of Conformity
Linn Products Ltd declare that this product is in conformance with the Low Voltage Directive 73/23/EEC and
Electromagnetic Compatibility 89/336/EEC as amended by 92/31/EEC and 93/68/EEC.
The conformity of the designated product with the provisions of Directive number 73/23/EEC (LVD) is proved by
full compliance with the following standards:
Standard number Date of issue Test type
EN60065 2002 General requirements
Marking
Hazardous radiation
Heating under normal conditions
Shock hazards under normal
operating conditions
Insulation requirements
Fault conditions
Mechanical strength
Parts connected to the mains supply
Components
Terminal devices
External flexible cords
Electrical connections and mechanical fixings
Protection against electric shock
Stability and mechanical hazards
Resistance to fire
The conformity of the designated product with the provisions of Directive number 89/336/EEC (EMC) is proved by
full compliance with the following standards:
Standard number Date of issue Test type
EN55013 2001 Conducted emissions
EN55013 2001 Absorbed emissions
EN55020 2002 Immunity
FCC notice
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
●Reorient or relocate the receiving antenna.
●Increase the separation between the equipment and receiver.
●Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
●Consult the dealer or an experienced radio/TV technician for help.
ii
Important Safety Information
English
AKURATE Loudspeaker System
Owner’s Manual
Copyright and Acknowledgements
Copyright (c) 2009 Linn Products Ltd. First edition July 2003, updated February 2009.
Linn Products Limited, Glasgow Road, Waterfoot, Eaglesham, Glasgow, G76 OEQ,
Scotland, United Kingdom
All rights reserved. No part of this publication may be reproduced, stored in a retrieval
system, or transmitted, in any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without the prior written permission of the
publisher.
Printed in the United Kingdom.
Trade marks used in this publication: L
Linn and the Linn logoare registered trade marks
of Linn Products Limited. AKURATEACHAKRACHAKRA KTIV,
, , SEKRIT and SKEETS are trade
marks of Linn Products Limited.
The information in this manual is furnished for informational use only, is subject to
change without notice, and should not be construed as a commitment by Linn Products
Limited. Linn Products Limited assumes no responsibility or liability for any errors or
inaccuracies that may appear in this manual.
PACK 897/4
iii
AKURATE Loudspeaker System
Owner’s Manual
Copyright and Acknowledgements English
Contents
1n
oi
tcu
dortnI
T1met
sy
s ETARU
KA eh
2se
r
u
tae
F
AKURATE 242, 225 and 212 3
3g
n
i
kca
pnU
F3se
llirg cirba
3g
n
inaelC
Positioning and levelling 4
C6g
n
i
tcenn
o
6lar
e
neG
7gniriw-elgniS
Bi 7gnipma-ib ro gniriw-
T7g
nipma
-
i
r
t ro gniri
w
-ir
Important notes on using the link strips 7
7dnoy
e
b
dna g
n
ipma-dauQ
8tsooB ssa
B
8noitarepo
VITKA
AKURATE 226 9
9 g
n
i
k
capnU
Po 9gninoitis
9 gninaelC
C01gnitcenno
11noitarepO
11sedom gnitarepO
Par 11sretema
Technical Specifications 13
Guarantee and Service 14
AKURATE Loudspeaker System
Owner’s Manual
Contents English
Introduction
At Linn, we recognise that the way people access sound is changing.
Entertainment systems are becoming ever more integrated and the line
between music and movie systems is no longer clear. As the popularity of new
and improved hi-resolution music formats increases, multi-channel systems are
no longer for the movie enthusiast only.
As we change the way we access sound, the equipment we use to relay that
sound must also change. A modern loudspeaker must offer greater levels of
flexibility, reproduce a wider range of sounds and playback at a higher
resolution to truly communicate the full potential of the system. The
loudspeaker communicating the awesome force of an explosion in a movie
blockbuster must be subtle enough to replay the tone and emotion of the
softest female jazz vocal.
With this in mind, Linn presents AKURATE - a system of complementary
loudspeakers, visually and sonically designed to achieve seamless multi-channel
performance.
The AKURATE system
AAKURATE 242 – A five-way, bass reflex, floorstanding loudspeaker, precision
engineered for use in medium to large sized listening areas. The AKURATE 242
speaker incorporates dual 6 1/2” (16.5 cm) drivers mounted vertically for
controlled, tuneful and extended bass performance.
AKURATE 212 – A compact, high-performance, four-way, bass reflex, bookshelf
loudspeaker. It features a single 6 1/2” (16.5 cm) bass driver and is designed for
use as a main speaker in smaller rooms or surround channel effects
applications. A custom designed stand is available for this model to allow
positioning for optimum performance.
AKURATE 225 – A centre channel loudspeaker designed primarily to match the
AKURATE 242 speakers. The AKURATE 225 speaker uses the same drive unit
complement as the AKURATE 242 speaker and has been tolerance-matched to
the other AKURATE loudspeakers to allow seamless system integration. A
custom designed stand is available for this model to allow positioning for
optimum performance.
AKURATE 226 - Bass extension in the AKURATE system is provided by the
servo-controlled AKURATE 226 bass reinforcement loudspeaker. The unit is
driven by a 500 W power amplifier and features a 10" (25.4 cm) servo-controlled
driver in a 25-litre enclosure for a pure and precise bass response.
1
AKURATE Loudspeaker System
Owner’s Manual
Introduction English
AKURATE 226
NNew 500 Amplifier Module The AKURATE 226 bass reinforcement loudspeaker
utilises 500 watts of servo-assisted Linn CHAKRA power amplification. The bass
drive unit is constantly monitored and regulated to maintain accurate, extended
bass in any listening environment.
Entire System
Magnetic Shielding To avoid magnetic interference with other household
products such as a television or a mobile communications device, all of the
loudspeakers within the AKURATE system are magnetically shielded.
SEKRIT-Fastener Invisible, flush-fitting, speaker grille technology.
2
Features
AKURATE 242, 225 and 212
Linn 3-K Driver Array(patent pending) Linn designed and engineered drive unit
array delivers optimised dispersion and high frequency performance. Provides
open and natural presentation and clear, precise dialogue and effects. All
components used in the 3-K Array are matched to a close tolerance, retaining
sonic purity and consistency throughout.
Unique Linn Loudspeaker Configuration System Input connector system enabling
passive multi-wiring/amplifier operation and a simple, clear upgrade path to an
active system. You can begin with a complete, high quality, passive loudspeaker
system and achieve performance enhancements through easy upgrade to full
active operation.
High Quality 61/
2” (16.5 cm) Sandwich-Cone Bass Drive Units Layered cone design
delivers pitch accurate, musical, bass extension.
AKURATE 242 and 225
Bass Extension Feature Allows calibrated tailoring of the bass response to suit
room acoustics or environment.
AKURATE 242 and 212
Acoustically Matched Double-Flared Ports Unique, mirrored “rifling” design
reduces turbulence and matches the impedance of internal cabinet volume with
the external environment.
AKURATE Loudspeaker System
Owner’s Manual
Introduction
English
W
TThe AKURATE 212 bookshelf speakers are supplied with the following
accessories:
●12 terminal link strips (four of which are factory fitted to the terminals);
4 x four-hole, 4 x three-hole, 4 x two-hole
●4 speaker plugs
●2 foam bungs
●terminal collar tool
●spike kit
●warranty card
●this manual
We recommend that you retain the packaging in case you need to transport
your speaker(s) at a later date.
3-K Array cover
To remove the protective cover from the 3-K Array, carefully cut through the
two cable ties. The cover should come away easily.
Fabric grilles
The AKURATE 242, 225 and 212 speakers are supplied with fabric grilles. The
grilles are held in place by SEKRIT-Fasteners (shielded magnets hidden within
the cabinets). Grilles can easily be removed by sliding them downwards (away
from the magnets) and gently pulling them towards you.
IMPORTANT:
Do not attempt to remove the metal grilles covering the drivers.
Cleaning
Remove dust and fingerprints from the cabinets with a soft, dry, lint-free cloth.
Avoid using domestic cleaning products as they may damage the veneer.
The grilles should be removed from the cabinets and cleaned carefully with a
soft brush.
3
AKURATE 242, 225 and 212
Unpacking
The AKURATE speakers are heavy; take care when removing them from their
packaging.
The AKURATE 242 floorstanding speakers are supplied with the following
accessories:
●speaker stand kit
●20 terminal link strips (four of which are factory fitted to the terminals);
4 x five-hole, 4 x four-hole, 4 x three-hole, 8 x two-hole
●4 speaker plugs
●4 foam bungs
●terminal collar tool
●spike adjustment tool
●warranty card
●this manual
The AKURATE 225 centre speaker is supplied with the following accessories:
●10 terminal link strips (two of which are factory fitted to the terminals);
2 x five-hole, 2 x four-hole, 2 x three-hole, 4 x two-hole
●2 speaker plugs
●terminal collar tool
●spike kit
●warranty card
●this manual
AKURATE Loudspeaker System
Owner’s Manual
AKURATE 242, 225 and 212 English
Positioning and levelling
To get the best from your Linn AKURATE speakers, it is important that they are
positioned and levelled correctly. The acoustics of a room are dependent on
many factors including size, shape and even furniture. The information below
will assist in helping you find the best position in your room for your speakers
and will tell you how to level them correctly.
Positioning
It pays dividends to experiment with loudspeaker positioning. However, the very
nature of the 3-K Array and its close driver proximity ensures uniform
dispersion characteristics and therefore should not require any significant
degree of toeing-in to improve performance.
A loudspeaker placed too close to a wall will tend to affect bass definition
creating a bass ‘bloom’, so a minimum of 9” (23 cm) is recommended between
the back of a speaker and the closest wall. If lack of space is an issue, foam
bungs are provided for insertion into the AKURATE 242 and 212 speakers’ rear
reflex ports to seal the cabinets. This converts the speakers to an infinite baffle
design and allows them to be placed closer to a wall. The AKURATE speaker
system will work effectively in free space, but if bass extension is limited the
AKURATE 242 and 225 speakers contain a Bass Boost feature to enhance the
bass frequencies below 200 Hz (see
Bass Boost
section).
4
AKURATE Loudspeaker System
Owner’s Manual
AKURATE 242, 225 and 212
English
Centre
Bass
reinforcement
loudspeaker
min. 9" (23 cm) min. 9" (23 cm)min. 9" (23 cm)
min. 9" (23 cm)
min. 9" (23 cm)
Levelling
All components in the AKURATE speaker system benefit from levelling, which
produces distinct improvements in soundstage and accuracy. A properly
levelled loudspeaker will always perform more effectively than an unstable one.
The actual loudspeaker cabinet can remain fixed whilst the drive units are
allowed to move as precisely determined by the playback signal from the
amplifier. Adjustable spikes or feet enable levelling on uneven floors, however
these adjustments are subtle and will not compensate for excessively irregular
floors.
Spikes are supplied with the AKURATE 242 speakers and the stand for the
AKURATE 225 and 212 speakers.
The procedure for levelling each speaker should be as follows:
●Use a spirit level on the top of the speaker to check if it is sitting level. If
it is, gently rock the speaker from front to back, side to side and
diagonally to check for any movement. If none is present and the speaker
is sitting level, no adjustment to the spikes is necessary.
●If the speaker is not level, or moves when you rock it, loosen the
appropriate lock nuts using the tool provided (1) and use a screwdriver to
turn the spikes to adjust their height (2).
●Press down firmly on the top of the speaker to ensure it is in close
contact with your flooring.
●Use the spirit level as before and continue to adjust the spikes as
required.
●When the speaker is level and does not rock, use the screwdriver to hold
the spikes in place and tighten the lock nuts using the tool provided (3).
Note:
To protect wooden or tiled floors the spikes can be placed on Linn SKEETS
which are available from your Linn retailer.
5
AKURATE Loudspeaker System
Owner’s Manual
AKURATE 242, 225 and 212 English
(1) (2)
(3)
Connecting
General
IMPORTANT:
Before making any connections, switch off your power amplifier(s).
Ensure the positive (+) or red coloured connectors from your amplifier(s),
connect to the positive (+) connectors on your loudspeaker(s). And that the
negative (-) or black coloured connectors from your amplifier(s), connect to the
negative (-) connectors on your loudspeaker(s).
AKURATE 242 and 225
The AKURATE 242 and 225 speakers are supplied with several terminal link
strips. These strips can be connected to the terminals on the back of the
speakers to provide a wide variety of amplifier-speaker connection
configurations. The links connect two, three, four or five terminals together
allowing for single-wiring, bi-wiring, tri-wiring, or connection to up to five
separate power amplifier channels. The speakers are supplied from the factory
with the five-hole link strips attached.
AKURATE 212
The AKURATE 212 speaker is supplied with several link strips. These strips can
be connected to the terminals on the back of the speaker to provide a wide
variety of amplifier-speaker connection configurations. The links connect two,
three or four terminals together allowing for single-wiring, bi-wiring, tri-wiring
or connection to up to four separate power amplifier channels. The speakers are
supplied from the factory with the four-hole link strips attached.
To remove/fit the link strips:
●Carefully remove the blanking plugs that are in the terminals, using a thin
blade.
●Use the supplied tool to unscrew the terminal collars.
●Remove/fit the required link strips.
●Replace all the terminal collars, making sure they are tightly secured.
●Replace the blanking plugs.
6
AKURATE Loudspeaker System
Owner’s Manual
AKURATE 242, 225 and 212
English
7
AKURATE Loudspeaker System
Owner’s Manual
AKURATE 242, 225 and 212 English
Tri-wiring or tri-amping
Suggested position of link strips if tri-wiring (i.e. using three pairs of cables
from one power amplifier) or tri-amping (i.e. using one pair of cables from each
of three power amplifier channels).
Important notes on using the link strips
The above configurations are only suggestions; many others are possible. If you
are trying other setups please bear in mind the following points.
●Never use the strips to link positive (+) and minus (-) terminals together.
●Don’t connect more than one strip per terminal.
●Bass quality will be impaired if you link LOWER BASS and BASS BOOST
together or UPPER BASS, LOWER BASS and BASS BOOST together.
Quad-amping and beyond
Improved audio quality can be obtained by connecting separate power
amplifiers to each pair of speaker terminals (bar the BASS BOOST terminals,
see next page). However, for the best audio performance your AV/hi-fi system
should be converted from running passively to running actively (see
AKTIV
operation
section).
AKURATE 242 and 225 AKURATE 212
TWEETERMID RETEEWT REPUSSSAB REPPULOWER BASSBASS BOOST
ACTIVE
TWEETERMID R
E
TEEWT
R
E
PUSSS
A
B
ACTIVE
Output from
power amplifier
can be
connected to
either of the
two terminals.
Output from
power amplifier
can be
connected to
either of the
two terminals.
Output from
power amplifier
can be
connected to
either of the
two terminals.
Single-wiring
Position of link strips if single-wiring (i.e. using a single pair of cables from one
stereo power amplifier).
Bi-wiring or bi-amping
Suggested position of link strips if bi-wiring (i.e. using two pairs of cables from
one power amplifier) or bi-amping (i.e. using one pair of cables from each of two
power amplifier channels).
AKURATE 242 and 225 AKURATE 212
TWEETERMID RETEEWT REPUSSSAB REPPULOWER BASSBASS BOOST
ACTIVE
TWEETERMID R
ET
EEW
T
R
EP
USSS
A
B
ACTIVE
Output from
power amplifier
can be
connected to
any of the five
terminals.
Output from
power amplifier
can be
connected to
any of the four
terminals.
AKURATE 242 and 225 AKURATE 212
TWEETERMID RETEEWT REPUSSSAB REPPULOWER BASSBASS BOOST
TWEETERMID R
ET
EE
W
T
R
EPUS
S
SA
B
ACTIVE
ACTIVE
Output from
power amplifier
can be
connected to
any of the three
terminals.
Output from
power amplifier
can be
connected to
either of the
two terminals.
Output from
power amplifier
can be
connected to
any of the three
terminals.
AKTIV operation
The AKURATE 242, 225 and 212 speakers can be either passively or actively
driven. In a passive system, the output from a power amplifier is passed
through the crossovers housed in the loudspeakers. This results in a certain
loss of audio signal as some of the energy in the signal is absorbed by the
crossover circuitry. In an active system, or in Linn terms - AKTIV system, the
crossover circuitry is placed before the power amplifier instead. After passing
through the crossover, the signal is amplified and sent to the drive units in the
speaker, bypassing the speaker’s crossover and therefore not losing that bit of
energy. This results in significantly improved audio performance.
AKURATE speakers are shipped in a passive configuration. If you wish to run
your speakers actively, you must have one Linn power amplifier channel for
each drive unit in the speakers and each amplifier must be fitted with the
correct AKTIV crossovers (contact your Linn retailer for further information).
The last step is to convert your AKURATE speakers from passive to active.
Your Linn retailer will do this for you.
The Bass Boost feature (see left) is not available if a speaker is being actively
driven.
Note:
The AKURATE 242, 225 and 212 speakers can be driven partially active, i.e.
either the 3-K Array or the bass driver(s) can be actively driven.
IMPORTANT NOTES ON AKTIV SYSTEMS
Do not use your amplifiers with any other loudspeakers – you may damage the
loudspeakers.
Do not use your loudspeakers with any other amplifiers – their internal
crossovers will be bypassed and the drivers could be severely damaged.
Do not use the terminal link strips – they can only be used in a passive system.
8
AKURATE Loudspeaker System
Owner’s Manual
AKURATE 242, 225 and 212
English
Bass Boost (AKURATE 242 and 225 only)
Depending on the position of the speakers in your room, or room acoustics, you
may wish to boost the lower bass frequencies (those under 200 Hz). This is
done by connecting the output from a power amplifier to the BASS BOOST
terminals on the rear panel.
If you are bi-wiringFit the four-hole link strips to the top four positive (+) and
minus (–) terminals. Connect one pair of speaker cables from the amplifier to
the linked terminals and the other pair to the BASS BOOST terminals.
If you are bi-amping Fit the three-hole link strips to the top three positive (+)
and minus (–) terminals. Connect one pair of speaker cables from one amplifier
channel to the linked terminals, and bi-wire from the second amplifier channel
to the UPPER BASS and BASS BOOST terminals.
If you are tri-wiringFit the three-hole link strips to the top three positive (+)
and minus (–) terminals. Connect one pair of speaker cables from the amplifier
to the linked terminals, a further pair to the UPPER BASS terminals and the
remaining pair to the BASS BOOST terminals.
If you are tri-amping Fit the two-hole link strips to the top two positive (+) and
minus (–) terminals. Connect a pair of speaker cables from one amplifier
channel to the linked terminals, a pair from another amplifier channel to the
MID terminals and bi-wire from the remaining amplifier channel to the UPPER
BASS and BASS BOOST terminals.
Note:
If you are using four or five amplifier channels per speaker you do not need to
use any of the link strips.
10
AKURATE Loudspeaker System
Owner’s Manual
AKURATE 226
English
FROM LINN SYSTEM CONTROLLER
OR OTHER AV PROCESSOR
HP OUT
AL OUT
A IN
FROM STEREO PRE-AMP
HP OUT
AL OUT
A IN
FROM STEREO PRE-AMP
TO POWER AMPLIFIER
HP OUT
AL OUT
A IN
FROM LINN SYSTEM
CONTROLLER
OR OTHER
AV PROCESSOR
AKURATE 226 - ONE
AKURATE 226 - TWO
HP OUT
AL OUT
A IN
HP OUT
AL OUT
A IN
FROM
STEREO
PRE-AMP
FROM
STEREO
PRE-AMP
AKURATE 226 - ONE
AKURATE 226 - TWO
HP OUT
AL OUT
A IN
HP OUT
AL OUT
A IN
Connecting
Connect the AKURATE 226 speaker to a mains supply using the mains lead
provided.
IMPORTANT:
Do not turn on the mains supply until you have connected all other
components.
Connecting to a Linn System Controller or other
AV processor
Connecting to a stereo pre-amplifier if used with large (full-range
frequency response) speakers, for example AKURATE 242 or 212 speakers.
Connecting to a stereo pre-amplifier and power amplifier if used
with ‘small’ (limited bass response) speakers.
Note:
In the above configuration the AKURATE 226 speaker is being used to stop
low bass notes from being sent to the main speakers.
Connecting to another AKURATE 226 speaker
OR
11
AKURATE Loudspeaker System
Owner’s Manual
AKURATE 226 English
Parameters
The AKURATE 226 speaker is equipped with eight adjustable parameters (see
next page) that enable you to alter its performance to suit your taste.
Note:
The parameters can only be adjusted when the AKURATE 226 speaker is not in
standby mode.
Adjusting the parameters
To select the parameter you wish to adjust:
●Hold FEATURE.
●Repeatedly press UPor DOWN until the letter for the desired parameter
appears.
●Release FEATURE.
●Repeatedly press UP or DOWN to change the setting.
A few seconds after the last key press the display
changes to
To restore the default settings:
●Disconnect the AKURATE 226 speaker from the mains supply and wait for
the display to go blank.
●While holding FEATURE reconnect the mains supply.
●Continue to hold FEATURE until the display shows
H
A few seconds after releasing FEATUREthe display changes to
HP OUT
AL OUT
A IN
-
-
Operation
When you have made all the required connections, switch on the mains supply.
Flashing bars will be shown on the back panel display for approximately 5
seconds. During this time the speaker’s servo circuitry is stabilising and no
audio will be issued. When the display changes to show the standby symbol (see
table below), the speaker is ready to receive an audio signal.
Whenever the AKURATE 226 speaker is disconnected from the mains supply
and then reconnected, wait until the standby symbol appears on the display
before playing a disc.
Operating modes
SYMBOL MODEMEANING
Standby The unit is waiting for an audio signal
In this mode the unit consumes minimal
power.
On The unit is fully powered-up
The unit will enter this mode as soon as it
receives an audio signal.
Thermal Standby The unit has overheated
During very demanding, sustained use the
unit will go into Thermal Standby mode in
order to allow itself to cool down. When in
this mode the unit will not produce any
sound. The unit will return to On mode
when its temperature has dropped to its
operating level.
Key to symbols
12
AKURATE Loudspeaker System
Owner’s Manual
AKURATE 226
English
Description and available settings for parameters
Default settings are shown in grey.
* Only for use when the AKURATE 226 speaker is connected to a power
amplifier (see Connecting section in this chapter).
** If you are using the AKURATE 226 speaker with a Linn System
Controller or other AV processor, set to 4 (No filtering).
Parameter Symbol 0 1 2 3 4 5 6 7 8 9
5
32
0
91
0
6
1
5
3
1
5
11
0
0
1
57
05
0
1
04
43
03
52
22
8
1
03
1
58
5
5
51+ 0
1
+ 5+ 0 5- 01-
5
1-
4
+ 3+ 2+ 1+ 0
External high pass
frequency.*
Increasing the setting
reduces the bass content
sent to the external
loudspeakers. (Hz)
Internal high pass
frequency.
Increasing the setting raises
the lowest frequency
produced by the unit. (Hz)
Internal low pass
frequency.**
Increasing the setting raises
the highest frequency
produced by the unit.
Reducing the setting lowers
the highest frequency
produced by the unit. (Hz)
Coarse gain. Every one step
increase in the setting raises
the gain (volume) of the
loudspeaker by 5 decibels.
Every one step decrease in
the setting lowers the gain
(volume) of the loudspeaker
by 5 decibels. (dB)
Fine gain. Every one step
increase in the setting raises
the gain (volume) of the
loudspeaker by 1 decibel.
(dB)
No filtering
6
+ 3
+
0
0
2 01
5
Bass equalisation.
Every one step increase in
the setting applies an
additional 3dBs at 30 Hz and
below. (dB@30 Hz)
Time out. Length of time
Phase. Depending on the
position of the Akurate 226
loudspeaker relative to
others in the system, better
performance may be
achieved by changing this
setting.
before unit will go into
standby after audio input
ceases. (mins)
Parameter Symbol 0 1 2 3 4 5 6 7 8 9
Always onnormal (0°)
inverted (180°)
13
AKURATE Loudspeaker System
Owner’s Manual
Technical Specifications English
AKURATE 242 AKURATE 225 AKURATE 212
T
ype 5-way floorstander 5-way centre 4-way bookshelf
Drive units 13 mm / 25 mm / 13 mm / 25 mm / 13 mm / 25 mm /
75 mm domes, 75 mm domes, 75 mm domes,
2 x 165 mm bass units 2 x 165 mm bass units 1 x 165 mm bass unit
Efficiency 87 dB for 1 watt at 1 m 87 dB for 1 watt at 1 m 87 dB for 1 watt at 1 m
)
zHk 1
(
)
z
H
k
1()
z
H
k
1
(
Crossover Passive / active Passive / active Passive / active
options
Frequency 49 Hz - 33 kHz 66 Hz - 33 kHz 70 Hz - 33 kHz
response -
passive
Frequency 40 Hz - 33 kHz 58 Hz - 33 kHz 50 Hz - 33 kHz
response -
active
Nominal 8
Ω
8
Ω
8
Ω
impedance -
passive
Impedance – 16
Ω
16
Ω
16
Ω
active (bass)
Impedance – 8
Ω
8
Ω
8
Ω
active (mid)
Impedance – 6
Ω
6
Ω
6
Ω
active (tweeter)
Impedance – 4
Ω
4
Ω
4
Ω
active
(super-tweeter)
Crossover All 4th order Linkwitz
297 Hz, 392 Hz,
3.73 kHz, 9.84 kHz
297 Hz, 392 Hz,
3.73 kHz, 9.84 kHz 3.6 kHz, 9.2 kHz
Connection options Up to 5-way by wire Up to 5-way by wire Up to 4-way by wire
or amplifier or amplifier or amplifier
s
eY
s
eY
se
Y
g
n
idleihs citen
g
aM
serti
l
21s
e
rtil 52
s
er
t
il
24
e
m
ulov gnitarepO
Dimensions 1000 mm (H) x 210 mm 250 mm (H) x 600 mm 350 mm (H) x 210 mm
(W) x 380 mm (D) (W) x 300 mm (D) (W) x 300 mm (D)
Weight 32 kg gk
21
g
k
1
2
Finishes Black Ash, Maple, Cherry, Black Ash, Maple, Cherry, Black Ash, Maple, Cherry,
Ros tun
es
oRtu
ne
soRtu
n
e
AKURATE 226
T Pitch-accurate bass reinforcement loudspeaker with integral active
amplification and equalisation circuitry
Features Active servo-controlled bass loudspeaker. 500 W RMS built-in amplifier
incorporating Chakra technology. Adjustable 2nd order roll-off for
seamless system integration. 25 litres operating volume. Signal
sensing auto switch on/off for energy
Drive unit 254 mm (10”) servo-controlled
Output Power 500 W RMS, 1000 W PEAK
epy
Operating volume 25 litres
Internal Frequency Response Adjustable roll-off from 55 Hz - 130 Hz in 3 steps and flat (to allow
external low pass filtering). Default is 55 Hz
High Pass Filtered Output
Frequency Response
Adjustable from 10 Hz - 235 Hz in 9 steps. Default is 10 Hz
Audio Connections Line level audio input RCA phono (A IN)
Line level audio loop out RCA phono (AL OUT)
Line level high pass output RCA phono (HP OUT)
Line Input Impedance 18 k Ω
Parameter Adjustment - 4 step internal low pass frequency @ 55, 85, 130 Hz and flat
- 6 step internal high pass frequency from 18 Hz
- 40 Hz- 9 step external high pass frequency from 10 Hz
- 235 Hz- Gain adjustable 34 dB in 1 dB steps (-15 to +19 dB)
- 3 step Bass equalisation
- 4 step Time out (standby time after signal end), including 'Always On'
Magnetic shielding Yes
Protection Fully protected against overload, temperature, full short circuit and
overdrive
Mains Input voltage
(auto-sensing)
100 - 120 V
220 - 240 V
Mains Supply Frequency 50 - 60 Hz
Standy Power Consumption 9 W
Dimensions H 391 mm (including feet) x W 360 mm x D 381 mm
H 15.4 inches (including feet) x W 15 inches x D 14.1 inches
Weight 19 kg / 41 lbs 14 oz
Standard finishes Rosenut, Maple, American Cherry, Black Ash
Technical Specifications
Riley at 450 Hz,
14
AKURATE Loudspeaker System
Owner’s Manual
Guarantee and Service
English
Guarantee and Service
This product is guaranteed under the conditions which apply in the country Linn Products Limited
Glasgow Road
Waterfoot
Eaglesham
Glasgow G76 OEQ
Scotland, UK
Phone: +44 (0)141 307 7777
Fax: +44 (0)141 644 4262
Helpline: 0500 888909
Email: helpline@linn.co.uk
Website: www.linn.co.uk
of purchase and your statutory rights are not limited. In addition to any
statutory rights you may have, Linn undertake to replace any parts which
have failed due to faulty manufacture. To help us, please ask your Linn
retailer about the Linn warranty scheme in operation in your country.
In parts of Europe, the United States of America and some other markets,
extended warranty may be available to customers who register their
purchase with Linn within 30 days of purchase.
You can register your warranty online at www.linn.co.uk
Warning
Unauthorised servicing or dismantling of the product invalidates the
manufacturer’s warranty. There are no user serviceable parts inside the
product and all enquiries relating to product servicing should be referred
to authorised retailers only.
Technical support and information
For technical support, product queries and information, please contact
either your local retailer or Linn directly.
Full details of your local retailer/distributor can be found on the Linn web
site: www.linn.co.uk
Important
●Please keep a copy of the sales receipt to establish the purchase
date of the product.
●Please ensure that your equipment is insured by you during any
transit or shipment for repair.

Navigation menu