SK1603 2 M Rotary Support Fax

User Manual: M-RotarySupportFax

Open the PDF directly: View PDF PDF.
Page Count: 2

SK1603 Rev 2
M-ROTARY FAX COVER SHEET
Date: ______________________
Atten: Contrex Technical Support
Fax Number: 1-763-424-8734
From:
Name ______________________________________________ Ext___________________
Company _______________ Telephone #________________ Fax # _________________
We have ______ M-Rotary(s) that are used for: ____________________________________
__________________________________________________________________________
__________________________________________________________________________
Serial Communication Hookup: _____Yes _____No
Brief Description of the Problem: ________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
We are transmitting _____ pages, including:
this (two sided) Fax Cover Sheet,
a sketch of the system that the M-Rotary is integrated with.
Please turn the page to record any CPs that you have changed from the default value—>
Code# Description User
Record Code# Description User
Record
Please record the Control Parameters that you have changed from the default value:
CP-01 Setpoint 1
CP-02 Setpoint 2
CP-03 Setpoint 3
CP-04 Setpoint 4
CP-05 Setpoint 5
CP-06 Setpoint 6
CP-07 Setpoint 7
CP-08 Setpoint 8
CP-10 Master Setpoint
CP-11 Jog Setpoint
CP-12 Direct Analog Cmd
CP-14 Control Mode
CP-15 Engineering Units
CP-16 Lead Lines/Cut
CP-17 Follower Lines/Cut
CP-18 PPR - Follower
CP-19 RPM - Follower
CP-20 Master Minimum Spd
CP-21 Master Maximum Spd
CP-22 Low Speed Alarm
CP-23 High Speed Alarm
CP-24 Out of Position
CP-25 Lag Pulse Limit
CP-26 Lead Pulse Limit
CP-27 Batch Limit
CP-28 Alarm Format
CP-29 Output Format
CP-30 Sync Trend Enable
CP-31 Sync Phase
CP-32 Sync Phase Increment
CP-33 Sync Lead Auto Enable
CP-35 Sync Flag Polarity
CP-36 Sync Lead Divide
CP-37 Sync Follower Divide
CP-60 Acceleration Time
CP-61 Deceleration Time
CP-62 Gross Error Overspeed
CP-63 Gross Error Reset
CP-64 Gross Error Boundary
CP-65 Gain (Kp)
CP-66 Integral (Ki)
CP-67 Derivative (Kd)
CP-70 Device Address
CP-71 Baud Rate
CP-72 Character Format
CP-73 Control Mask
CP-90 Speed Match Ratio
CP-91 Minimum Profile Ratio
CP-92 Maximum Profile Ratio
CP-93 Start Match Point
CP-94 End Match Point
MV-59 Line Notch Counter
MV-74 Comm Error
MV-80 Lead Job Space Avg
MV-81 Follower Job Space Avg
MV-82 Lead Job Space Var
MV-83 Follower Job Space Var
MV-84 Sync Flag Difference
MV-85 True Scale Factor
MV-86 Active Scale Factor
MV-87 Lead Job Space Present
MV-88 Foll Job Space Present
MV-95 End Limit Point
MV-96 Start Limit Point
MV-97 Peak Ratio
MV-98 Profile Ratio
MV-99 Software Code Revision
MV-00 Software Part Number
Code# Description Displayed
Code# Description Displayed
Please record what the relevant Monitor Parameters display when the problem occurs:
MV-40 Tach - Cut Length
MV-41 Lead Frequency
MV-42 Feedback Frequency
MV-43 Feedback Velocity
MV-44 Product Rate
MV-45 Batch Count
MV-46 Batch Remaining
MV-47 DAC Output
MV-48 Trim Output
MV-49 Position Error
MV-50 Keypad Errors
MV-51 Alarm Status
MV-52 Control State
MV-53 Discrete IN A
MV-54 Discrete IN B
MV-55 Discrete IN C
MV-56 Discrete OUT A
MV-57 Discrete OUT B

Navigation menu