SK1605 2 M Shuttle Support Fax

User Manual: M-ShuttleSupportFax

Open the PDF directly: View PDF PDF.
Page Count: 2

SK1605 Rev 2
M-SHUTTLE FAX COVER SHEET
Date: ______________________
Atten: Contrex Technical Support
Fax Number: 1-763-424-8734
From:
Name ______________________________________________ Ext___________________
Company _______________ Telephone #________________ Fax # _________________
We have ______ M-Shuttle(s) that are used for: ____________________________________
__________________________________________________________________________
__________________________________________________________________________
Serial Communication Hookup: _____Yes _____No
Brief Description of the Problem: ________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
We are transmitting _____ pages, including:
this (two sided) Fax Cover Sheet,
a sketch of the system that the M-Shuttle is integrated with.
Please turn the page to record any CPs that you have changed from the default value—>
Code# Description User
Record Code# Description User
Record
Please record the Control Parameters that you have changed from the default value:
CP-01 Setpoint 1
CP-02 Process Length 1
CP-03 Setpoint 2
CP-04 Process Length 2
CP-05 Setpoint 3
CP-06 Process Length 3
CP-07 Setpoint 4
CP-08 Process Length 4
CP-09 Accel/Decel Length
CP-10 Foward Dwell
CP-11 Reverse Dwell
CP-12 Process Ratio
CP-13 Max Recovery Ratio
CP-14 Control Mode
CP-15 Engineering Units
CP-16 Lead Lines per CP-15
CP-18 PPR - Follower
CP-19 Max RPM - Follower
CP-21 Kerf Length
CP-22 Process Length Timer
CP-23 High Speed Alarm
CP-24 Deviation Band
CP-25 Dev Band Interval
CP-27 Batch Limit
CP-28 Alarm Format
CP-29 Unipolar/Bipolar
CP-30 At-Home Band
CP-31 Home Offset
CP-32 Sync Lead Offset
CP-33 Sync Trend Enable
CP-34 Sync Lead Delay
CP-35 Sync Flag Polarity
CP-36 Sync Lead Divide
CP-37 Sync Lead Window
CP-38 Sync Lead Wdo Frmt
CP-39 Fwd/Rev Lmt Polarity
CP-60 Accel/Decel
CP-61 Jog Setpoint
CP-62 Direct Analog Cmd
CP-65 Gain (Kp)
CP-66 Integral (Ki)
CP-68 Intagral Activation
CP-70 Device Address
CP-71 Baud Rate
CP-72 Character Format
CP-73 Control Mask
CP-79 Keypad Lockout Mask
CP-90 Output A Format
CP-91 Output A Delay
CP-92 Output A Interval
CP-93 Output B Format
CP-94 Output B Delay
CP-95 Output B Interval
MV-57 Discrete OUT B
MV-58 Invalid Profile
MV-59 Line Notch Counter
MV-74 Comm Error
MV-80 Lead Job Size
MV-81 Follower Job Size
MV-82 Start Limit Point
MV-83 End Limit Point
MV-84 Follower Profile Length
MV-85 Trended Ratio
MV-86 Computed Ratio
MV-87 Profile Ratio
MV-88 Peak Recovery Ratio
MV-89 Batch Count
MV-99 Software Code Revision
MV-00 Software Part Number
Code# Description Displayed
Code# Description Displayed
Please record what the relevant Monitor Parameters display when the problem occurs:
MV-40 Tach - Velocity
MV-41 Lead Frequency
MV-42 Feedback Frequency
MV-43 Lead Position
MV-44 Follower Position
MV-45 Product Rate
MV-46 Process Error
MV-47 DAC Output
MV-48 Trim Output
MV-49 Position Error
MV-50 Keypad Errors
MV-51 Alarm Status
MV-52 Control State
MV-53 Discrete IN A
MV-54 Discrete IN B
MV-55 Discrete IN C
MV-56 Discrete OUT A

Navigation menu