Lanzar MAX MXA422 Amplifier User’s Manual MXA232 242 252 282 412 422
User Manual: Lanzar MAX MXA422 Amplifier User’s Manual Troubleshoot Lanzar MAX MXA422 Amplifier |
Open the PDF directly: View PDF .
Page Count: 9
Download | |
Open PDF In Browser | View PDF |
Lanzar Audio Inc. 1600 63rd Street, Brooklyn, NY 11204 (718) 236-8000 www.lanzar.com Fe ature s and Co ntro ls M X A 2 3 2 /2 42 /2 52 /2 8 2 Congratulations on your purchase of a Lanzar MAX PRO amplifier. You have purchased a quality product designed and engineered to give you many years of uncompromised musical service. MAX PRO amplifiers are designed with the latest technology available, which provides headroom for even the most demanding peaks and dynamic ranges found on modern CD's and recordings. TABLE OF CONTENTS Table of Contents Feature and Controls 1. MXA 232/242/252/282 2. MXA 412/422 3. Installation 4. Specifications Max Pro Owner’s Manual 1. INPUT LEVEL CONTROLS Enables the matching of input levels to the output levels from head unit (or other signal source). System Wiring 6. 2 channel stereo 7. 2 channel bridged mode 8. 2 channel tri-mode 9. 2 channel triamp system 10. 4 channel stereo 11. 4 channel bridged mode 12. 4 channel tri-mode 13. Precautions 14.Troubleshooting 15.Notes 2. CROSSOVER MODE SELECTOR Determines the mode of built-in crossover: low pass (permits only low frequency signals to pass to speakers), high pass (permits only high frequency signals to pass to speakers), or flat. 3. BASS BOOST CONTROL With a bass boost switch engaged, the bass level is increased approx 18dB. 4. REMOTE BASS BOOST Plug in the remote bass boost control wire in here 5. POWER & PROTECTION INDICATORS Provide instant information on status of amplifier, including short-circuit and thermal overload alerts. 6. HIGH PASS FILTER (HPF) When Crossover Mode Selector is in High Pass Mode, this control limits the frequencies which will be distributed to the speakers to those below the value to which this is set within the range 802.5KHz. 7. LOW PASS FILTER (LPF) When Crossover Mode Selector is in Low Pass Mode, this control limits the frequencies which will be distributed to the speakers to those below the value to which this is set within the range 35400Hz. 8. PHASE SHIFT CONTROL 0-180 Allows you to change the phase of your high and low crossover from 0 to 180 degrees to help compensate for timing difference between drivers. Max Pro Owner’s Manual - 1 Fe ature s and Co ntro ls Insta l l ation M X A 41 2 /42 2 1. Find a suitable location in the vehicle to mount the amplifier. 2. Make sure there is sufficient air flow around the intended mounting location. 3. Bolt the amplifier to the mounting surface. 4. Connect the power ground terminal to the nearest point on the chassis of the car. Keep this ground wire less than one meter (39") in length. Use 8 gauge wire. 5. Connect the remote terminal to the remote output of the head unit using 14 gauge wire. 1. INPUT LEVEL CONTROLS Enables the matching of input levels to the output levels from head unit (or other signal source). 2. CROSSOVER MODE SELECTOR Determines the mode of built-in crossover: low pass (permits only low frequency signals to pass to speakers), high pass (permits only high frequency signals to pass to speakers), or flat. 3. BASS BOOST CONTROL With a bass boost switch engaged, the bass level is increased approx 18dB. 4. REMOTE BASS BOOST Plug in the remote bass boost control wire in here 5. POWER & PROTECTION INDICATORS Provide instant information on status of amplifier, including short-circuit and thermal overload alerts. 6. HIGH PASS FILTER (HPF) When Crossover Mode Selector is in High Pass Mode, this control limits the frequencies which will be distributed to the speakers to those below the value to which this is set within the range 802.5KHz. 7. LOW PASS FILTER (LPF) When Crossover Mode Selector is in Low Pass Mode, this control limits the frequencies which will be distributed to the speakers to those below the value to which this is set within the range 35400Hz. 8. PHASE SHIFT CONTROL 0-180 Allows you to change the phase of your high and low crossover from 0 to 180 degrees to help compensate for timing difference between drivers. 2 - Max Pro Owner’s Manual 6. Connect an empty fuse holder within 300mm (12") of the battery and run 8 gauge of larger high quality cable from this fuse to the amplifier location. 7. Make sure there is no fuse in this fuse holder. Then make the connection to the "BATT" connection on the amplifier. 8. If multiple amplifiers are being used, use cables (each with its own fuse at the battery) or a #0 or #2 cable from the fuse holder at the battery to a distribution block at or near the amplifier's location. 9. Connect all line inputs and outputs using high-quality RCA-RCA cables. 10. Insert fuse(s) at the battery fuse holder(s). 11. Recheck all connections before powering up. 12. Set all level controls to their least sensitive positions and set all crossover controls, switches, etc. to the desired frequency or position. 13. Once the system is powered up, set the volume control on the head unit to about the 2 o'clock position, and then set all the amplifiers' level controls for maximum output level. 14. Further fine tuning of the various controls may be necessary to obtain the desired results. Max Pro Owner’s Manual - 3 S pec ific ations MODEL RMS at 4 Ohms MAX at 4 Ohms At 4 Ohms Bridged RMS at 2 Ohms Min. Speaker Impedance T.H.D. Frequency Response Input Sensitivity Input Impedance S/N Ratio Channel Separation Crossover Filters Low Pass High Pass Bass Boost Dimensions (WxHxL) Fuse(s) 4 - Max Pro Owner’s Manual S pec ific ations channel MXA 232 2amplifier channel MXA 242 2amplifier channel MXA 252 2amplifier channel MXA 282 2amplifier channel MXA 412 4amplifier channel MXA 422 4amplifier 2 x 75W 2 x 125W 2 x 200W 2 x 300W 4 x 35W 4 x 75W 2 x 500W 2 x 800W 2 x 1200W 2 x 2000W 4 x 250W 4 x 500W 1 x 1000W 1 x 1600W 1 x 2400W 1 x 4000W 2 x 500W 2 x 1000W 2 x 100W 2 x 200W 2 x 300W 2 x 450W 4 x 55W 4 x 120W 2 ohm 2 ohm 2 ohm 2 ohm 2 ohm 2 ohm 0.04% 0.04% 0.04% 0.04% 0.04% 0.04% 15Hz-35KHz, -1dB 15Hz-35KHz, -1dB 15Hz-35KHz, -1dB 15Hz-35KHz, -1dB 15Hz-35KHz, -1dB 15Hz-35KHz, -1dB 250mV-5000mV 250mV-5000mV 250mV-5000mV 250mV-5000mV 250mV-5000mV 250mV-5000mV 22 Kohm 22 Kohm 22 Kohm 22 Kohm 22 Kohm 22Kohm >90dB >90dB >90dB >90dB >90dB >90dB >65dB >65dB >65dB >65dB >65dB >65dB 35Hz-400Hz 80Hz-2.50KHz 35Hz-400Hz 80Hz-2.50KHz 35Hz-400Hz 80Hz-2.50KHz 35Hz-400Hz 80Hz-2.50KHz 35Hz-400Hz 80Hz-2.50KHz 35Hz-400Hz 80Hz-2.50KHz +18dB +18dB +18dB +18dB +18dB +18dB 10.47"x2.46"x12" 10.47"x2.46"x15" 10.47"x2.46"x19" 10.47"x2.46"x21" 10.47"x2.46"x12" 10.47"x2.46"x17" 20A 30A 25Ax2 35Ax2 20A 20Ax2 Max Pro Owner’s Manual - 5 Syste m Wir ing 2 CHANNEL STEREO CONFIGURATION 6 - Syste m Wir ing MXA 232/242/252/282 MXA 232/242/252/282 2 CHANNEL BRIDGED MODE CONFIGURATION FRONT FRONT REAR REAR Max Pro Owner’s Manual Max Pro Owner’s Manual - 7 Syste m Wir ing 2 CHANNEL TRI-MODE CONFIGURATION Syst e m Wi r i ng MXA 232/242/252/282 MXA 232/242/252/282 TRIAMP SYSTEM USING THREE 2 CHANNEL AMPLIFIERS FRONT REAR 8 - Max Pro Owner’s Manual Max Pro Owner’s Manual - 9 Syst e m Wi r i ng 4 CHANNEL STEREO CONFIGURATION 10- Syst e m Wi r i ng MXA 412/422 MXA 412/422 4 CHANNEL BRIDGED MODE CONFIGURATION FRONT FRONT REAR REAR Max Pro Owner’s Manual Max Pro Owner’s Manual -11 Syst e m Wi r i ng 4 CHANNEL TRI-MODE CONFIGURATION Precautions VIBE 412/422 • Before you drill or cut any holes, investigate your car's layout very carefully. Take care when your work near the gas tank, fuel lines, hydraulic lines and electrical wiring. FRONT • Do not operate the amplifier when it is unmounted. Attach all audio system components securely within the automobile to prevent damage, especially in an accident. • Do not mount this amplifier so that the wire connection, or likely to be damaged by nearby objects. Be sure to select a location inside your vehicle which has adequate ventilation. • Before making or breaking power connections in your system, disconnect the vehicle battery. Confirm that your head unit or other equipment is turned off while connecting the input jacks and speaker terminals. • If you need to replace the power fuse, only replace it with a fuse indentical to that supplied with the system. Using a fuse of a different type or rating may result in damage to your system which isn't covered by the manufacturer's warranty. REAR 12- A mpl i f i er Wi l l Not P ower U p. • Check for good ground connection. • Check that remote DC terminal has at least 12V DC. • Check that there is battery power on the "+" terminal. • Check all fuses. • Check that Protection LED is not lit. If it is lit, shut off amplifier briefly and then repower it. Max Pro Owner’s Manual Max Pro Owner’s Manual -13 Tr o u b l e sho ot i ng Notes Hi g h Hi s s O r E n g i n e N oi s e (A lter n ator Wh i n e) I n S peak er s . • Disconnect all RCA inputs to the amplifier(s)-if hiss/noise disappears, then plug in the component driving the amplifier and unplug its inputs. If hiss/noise disappears, go on until the faulty/noisy component is found. • It is best to set the amplifier's input level as low as possible. The best subjective S/N ratio is obtainable this way. Try to drive as high a signal level from the head unit as possible. Pr otecti on Led Comes O n Wh en Th e A mpl i f i er I s P ower ed U p • Check for shorts on speaker leads. • Check that the volume control on the head unit is turned down low. • Remove speaker leads, and reset the amplifier. If the Protection LED still comes on, then the amplifier is faulty. A mpl i f i er (S ) Gets Very Hot • Check that the minimum speaker impedance for that model is correct. • Check for speaker shorts. • Check that there is good airflow around the amplifier. In some appliciations, an external cooling fan may be required. Di storted S oun d • Check that the level control(s) is set to match the signal level of the head unit. • Check that all crossover frequencies have been properly set. • Check for shorts on the speaker leads. Hi g h S queal N oi s e Fr om S peak er s • This is almost always caused by a poorly-grounded RCA patch cord. 14- Max Pro Owner’s Manual Max Pro Owner’s Manual -15
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Page Count : 9 XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:a37c9502-950b-43da-bc40-030aa54348e5 Modify Date : 2006:03:31 11:47:39-05:00 Create Date : 2006:03:31 11:46:09-05:00 Metadata Date : 2006:03:31 11:47:39-05:00 Document ID : uuid:08f0c824-cdee-4ed4-82d7-1f2cc090f334 Format : application/pdfEXIF Metadata provided by EXIF.tools