Manual 8.576.80.02 Colt M4 M16 22 Rimfire 10R11

User Manual: Manual-Colt-M4-M16-22-Rimfire-10R11

Open the PDF directly: View PDF .
Page Count: 32

Download
Open PDF In Browser	View PDF

Upper Receiver

M4 / M16
Self loading rifle
Cal. .22 L.R. HV

Front Sight

Handguards

Rear Sight

USA

Carry Handle

Muzzle

Compensator

Buttstock

Charging Handle

Rear Receiver Pin

Lower Receiver
Safety

Magazine Release
Handguards

Grip
Trigger

Buttstock Latch

Ejection Port Cover
Trigger Guard
Magazine

Safety And Operating Instructions

manual-8.576.80.02.indd 1

READ THE INSTRUCTIONS
AND WARNINGS IN THIS
MANUAL CAREFULLY BEFORE USING THIS FIREARM.

Warning:

made by carl walther

28.10.2011 07:07:42

No. Contents

Page

Identification

Safety Rules

3 - 11

Manual Safety

Inspection

Loading the Firearm

Loading the chamber with the first cartridge

Firing

Decocking

Firearm with empty Magazine

Unloading

Clearing Misfires

10 Settings - Sights, Stock, Bolt Speed

14 - 15
15
15-16

17 - 19

11 Mounting an optical sight

12 Field stripping

13 Cleaning

21 - 22

14 Storage

15 Repair

16 Warranty

Contents

17 Technical Data

23 - 24
25

18 Exploded view / Parts

26 - 28

19 Variants / Accessories

29 - 30

Contact

back

2
manual-8.576.80.02.indd 2

28.10.2011 07:07:42

YOUr safety responsibility
SAFETY IS YOUR NUMBER ONE RESPONSIBILITY!
AT HOME, IN THE FIELD, AT THE RANGE, OR ANYWHERE, THE FIRST CONCERN OF EVERY FIREARM OWNER SHOULD BE SAFETY. APPLY THE
FOLLOWING SAFETY RULES IN EVERY SITUATION, WITH ANY KIND OF FIREARM.

Warning:

YOU MUST FOLLOW ALL OF THESE SAFETY RULES TO ENSURE THE SAFE USE OF YOUR FIREARM

Warning:
SAFE USE OF A FIREARM IS YOUR PERSONAL RESPONSIBILITY AND THE FAILURE TO FOLLOW ALL OF THESE BASIC SAFETY RULES MAY
RESULT IN SEVERE PERSONAL INJURY OR DEATH TO YOU OR OTHERS. YOU ARE THE MOST IMPORTANT SAFETY DEVICE WHEN IT COMES TO
THE USE OF YOUR FIREARM. CARL WALTHER GMBH AND UMAREX USA WILL NOT BE RESPONSIBLE FOR ANY PERSONAL INJURY, DEATH OR
PROPERTY DAMAGE THAT RESULTS FROM:
(1) THE CRIMINAL OR NEGLIGENT USE OF THIS FIREARM;
(2) A DISREGARD OF THESE SAFETY INSTRUCTIONS AND WARNINGS;
(3) IMPROPER OR CARELESS HANDLING OF THIS FIREARM;
(4) THE USE OF NON-STANDARD, DEFECTIVE, IMPROPER OR RELOADED AMMUNITION; OR
(5) IMPROPER OR NEGLIGENT MODIFICATIONS OR REPAIR TO THE FIREARM.

3
manual-8.576.80.02.indd 3

Your Safety responsibilitiy

Warning:
SAFE GUN HANDLING IS YOUR PERSONAL RESPONSIBILITY!

28.10.2011 07:07:42

Your Safety responsibilitiy

SAFE GUN HANDLING IS YOUR PERSONAL RESPONSIBILITY at all times.
Firearms are dangerous and can cause serious injury or death if they are misused or used inappropriately. Safety must be the first
consideration of anyone who owns or handles firearms.

YOU ARE RESPONSIBLE FOR FIREARM SAFETY AT ALL TIMES.
You must undertake full-time responsibility for your firearm´s safety and security. You must protect yourself and all
others against injury or death from misuse of the firearm

SAFE FIREARM STORAGE IS YOUR RESPONSIBILITY.
You must secure firearms safely from children and unauthorized users. A lock has been provided for use with this firearm.
Never assume that the use of this lock is sufficient to safely secure your firearm. You must always evaluate your personal situation and
employ the security system(s) that meet your needs and prevent children and unauthorized users from gaining access to your firearm.

Accidents are the result of violating the rules of safe gun handling and common sense.

For your safety and the safety of others, NEVER RELY ON MECHANICAL FEATURES ALONE.
Only your safe gun handling habits will ensure the safe use of the firearm.
This is your responsibility.

NEVER KEEP AMMUNITION IN THE SAME LOCATION AS THE FIREARM.
Store in a separate and secure place.

DO NOT ALTER, MODIFY OR REPLACE ANY OF THE PARTS OF THE INTERNAL COMPONENTS OF YOUR FIREARM
All work must be performed by an Umarex USA authorized gunsmith. If you do otherwise, improper functioning may occur, serious injury
or death may result, and your warranty will be voided.

- NEVER MANIPULATE, ADJUST OR CHANGE ANY OF THE INTERNAL COMPONENTS OF
YOUR FIREARM
including the firing pin, sear, or drawbar. Improper manipulation of any internal component may
affect the safety and reliability of your firearm and may cause serious injury.

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE USING YOUR FIREARM

manual-8.576.80.02.indd 4

28.10.2011 07:07:42

WARNING:

BEFORE HANDLING ANY FIREARM, UNDERSTAND ITS OPERATION.
Not all firearms are the same. Familiarize yourself with the mechanical features of any firearm you intend to use. If you
feel uncertain about any operational aspects of your firearm, please contact Umarex USA before proceeding with its operation.

ALWAYS SAFELY STORE AND SECURE YOUR FIREARM.
Safe and secure storage of your firearm is one of the most important responsibilities of firearm ownership.
It is a full-time responsibility. You must always secure your firearm and ammunition separately so that they are not
accessible to children or other unauthorized persons. (See Safe Storage Instructions in this manual).

ALWAYS KEEP YOUR FIREARM POINTED IN A SAFE DIRECTION.
NEVER point this firearm at any person. Never point at anything you do not intend to shoot whether or not the firearm is loaded.
This is particulary important when loading, unloading, or field stripping the gun. ALWAYS control the direction of the muzzle.

NEVER PLACE YOUR FINGER ON THE TRIGGER OR INSIDE THE TRIGGER GUARD UNLESS YOU INTEND TO FIRE.
Ensure that other objects do not touch the trigger.

ALWAYS BE SURE OF YOUR TARGET AND WHAT IS BEYOND IT.
Always be sure of where the bullet will strike and shoot only where there is a safe backstop free of obstructions, water
or other surfaces which can cause ricochets. Think of what the bullet may hit if it misses the target or ricochets. Do not fire into the sky.

NEVER DISASSEMBLE YOUR FIREARM OR MANIPULATE THE INTERNAL COMPONENTS OF YOUR FIREARM
beyond the field stripping procedure outlined in this manual. Improper disassembly or manipulation of your
firearm may be dangerous and can lead to serious injury or death.

NEVER CARRY OR STORE A FIREARM with the hammer or striker in the cocked position.

5
manual-8.576.80.02.indd 5

Your safety responsibility

THE FAILURE TO FOLLOW THESE BASIC FIREARM SAFETY RULES MAY RESULT IN AN UNINTENDED
DISCHARGE WHICH COULD CAUSE SERIOUS PERSONAL INJURY OR DEATH TO YOU AND OTHERS.

28.10.2011 07:07:42

Your Safety responsibilitiy

NEVER ALLOW YOUR FIREARM TO BE USED BY INDIVIDUALS WHO HAVE NOT READ OR DO NOT UNDERSTAND THESE FIREARM
SAFETY RULES

BE SURE ALL ACCESSORIES, SUCH AS HOLSTERS AND GRIPS, ARE COMPATIBLE
with the firearm and that the accessories do not interfere with the safe operation.

ALWAYS USE THE CORRECT AMMUNITION FOR YOUR PARTICULAR FIREARM
as indicated by the marking on the barrel or receiver. Never use non-standard, reloaded, or “handloaded” ammunition which has
not been subjected to internal ballistic pressure testing.

ALWAYS HAVE ADEQUATE VENTILATION.
Discharging firearms in poorly ventilated areas, cleaning firearms, or handling ammunition may result in exposure to lead
and other substances known to cause birth defects, reproductive harm, and other serious physical injury. Review the
warning and labels for all ammunition and cleaning products carefully.

NEVER USE ALCOHOL OR DRUGS BEFORE OR WHILE SHOOTING.
Do not use your firearm if you are on any medication which impairs, even slightly, your mental physical ability.

ALWAYS WEAR EYE AND HEARING PROTECTION SPECIFIED FOR FIREARM USE
every time you discharge your firearm. Make sure others in the vicinity of where you will be shooting wear protection as well.

- NEVER ALLOW ANY ALTERATION OR REPLACEMENT OF PARTS IN YOUR FIREARM UNLESS
PERFORMED BY A QUALIFIED GUNSMITH.
If you do otherwise, improper functioning of your firearm may occur and serious injury or death may result.
-

NEVER CROSS OBSTACLES SUCH AS FENCES OR STREAMS WITH A LOADED FIREARM.

Firearm safety training is available. Contact your dealer, law enforcement agency, local sportman´s club, or the NRA for availability.

APPROPRIATE USE FOR YOUR FIREARM MEANS USING YOUR FIREARM FOR LEGAL PURPOSES.

manual-8.576.80.02.indd 6

28.10.2011 07:07:42

SAFE STORAGE & TRANSPORTATION

Warning:

You must always secure your firearm and ammunition separately so that they are not
accessible to children or other unauthorized persons.

Safe and secure storage and transportation of your firearm is your responsibility.
It is a full-time responsibility.

YOU SHOULD ALWAYS SECURE YOUR FIREARM IN A MANNER THAT WILL
PREVENT UNAUTHORIZED ACCESS. ALWAYS STORE YOUR FIREARM
UNLOADED.
Your firearm and ammunition should be stored separately and in a manner
inaccessible to children and unauthorized persons.
ALWAYS MAKE CERTAIN THAT YOUR FIREARM IS SAFELY SECURED IN A MANNER SO AS TO PREVENT
UNAUTHORIZED ACCESS TO THE FIREARM. CARL WALTHER has provided A LOCK for this purpose.
Please read and follow the instructions for the use of this lock. There are other alternative locks and
safe storage containers available in the marketplace which may be appropriate for your particular needs.
Consult your local gunshop, hardware store or local police department for guidance on the variety of other safe storage
devices or practices which may be appropriate for your particular needs. By purchasing this firearm you have taken
on the responsibility of safely securing the firearm at all times and preventing its unauthorized use. Never assume that
the use of only a lock is sufficient to safely secure your firearm. It is your personal responsibility to select and use
whatever measure or practices that will best enable you to be absolutely certain that your firearm is secure at all times.
You are responsible to determine which devices or practices are appropriate
for the safe storage of your firearm and your ammunition.
7
manual-8.576.80.02.indd 7

Your safety responsibility

SAFE AND SECURE STORAGE OF YOUR FIREARM IS ONE OF THE
MOST IMPORTANT RULES OF FIREARM SAFETY. YOUR FAILURE TO FOLLOW
THESE RULES MAY RESULT IN SERIOUS INJURY OR DEATH TO YOU OR OTHERS.

28.10.2011 07:07:43

Warning: NEVER LOCK A LOADED FIREARM AND NEVER LOAD A LOCKED FIREARM

Your Safety responsibilitiy

NEVER ASSUME THAT A ``HIDING`` PLACE IS A SECURE STORAGE METHOD.
Others may be aware of your storage location or come upon it by chance. It is your personal responsibility to use common sense when
storing and securing your firearm and ammunition and to always make sure that it is not accessible to children or other unauthorized
persons. Always make sure your firearm is unloaded before storing.

ALWAYS FOLLOW THE LAW!!
You must be familiar with all local, state, and federal laws regarding the safe discharge, storage and transportation of your firearm.
Failure to know and follow the law may result in unauthorized access or use of your firearm by another. Obey all laws relating to the
storage and transportation of firearms. Your local police department or gunshop will furnish you with available information
on storing and/or transporting a firearm legally.

NEVER TRANSPORT A LOADED FIREARM.
When transporting your firearm, be sure it is unloaded and the cylinder or action is open.

YOUR FIREARM IS YOUR RESPONSIBILITY.
Protect your firearm from theft or misuse by untrained or unqualified individuals.

PREPARATION FOR FIRING

Warning:

THE FAILURE TO FOLLOW THESE FIREARM SAFETY
REQUIREMENTS WILL CAUSE SERIOUS INJURY OR DEATH TO YOU OR OTHERS.
ALWAYS WEAR ADEQUATE AND PROPER EAR PROTECTION SPECIFIED
FOR FIREARM USE to prevent permanent damage to your hearing. Make sure others who are nearby are wearing ear protection as well.
-

ALWAYS WEAR SAFETY GLASSES SPECIFIED FOR FIREARM USE, whether indoors or out. Safety glasses should protect
your eyes from the firing flash and particles associated with the discharge of ammunition. Failure to do so creates a risk of
personal injury from particle or debris ejection or ricochets.

manual-8.576.80.02.indd 8

28.10.2011 07:07:43

NEVER SHOOT AT HARD SURFACES, WATER OR UP INTO THE SKY.
Always select a place to shoot that has a safe backstop and is free from obstruction and water surfaces which cause ricochets.

ALWAYS BE AWARE OF PEOPLE AROUND YOU so that persons cannot accidentally walk into the line of fire.

ALWAYS POSITION THE SHOOTER SO THAT ALL OTHERS ARE OUT OF THE LINE OF FIRE
and are not within an area where they may be struck by ricochets, or by ejected cases.

ALWAYS BE ALERT AND ALWAYS FOLLOW THE SAFETY INSTRUCTIONS OF FIRING RANGE OFFICER.

always BE SURE THAT ALL ACTIONS OF FIREARMS ARE OPEN, THAT CHAMBERS ARE CLEAR
OF AMMUNITION, MAGAZINES ARE REMOVED, AND THE FIREARM IS POINTING IN A SAFE DIRECTION.

ALWAYS BE ALERT.
Never shoot if you are tired, cold or impaired in any way.

ALWAYS TREAT YOUR FIREARM AS IF IT WERE LOADED.

NEVER USE ALCOHOL OR DRUGS BEFORE OR WHILE SHOOTING.

9
manual-8.576.80.02.indd 9

Your safety responsibility

ALWAYS KEEP FINGERS AND OTHER PARTS OF YOUR BODY AWAY FROM THE MUZZLE AND AWAY FROM THE FIREARM BOLT AND
EJECTION PORT.

28.10.2011 07:07:43

AMMUNITION
A GENERAL PRINCIPLES
-

There are different types of ammunition for different types of firearms. Your firearm has been designed for ammunition of a specific type
and a specific caliber. It is important to select the proper ammunition for your firearm.

Warning:

NEVER USE AMMUNITION NOT SPECIFICALLY DESIGNATED FOR USE IN YOUR FIREARM. FAILURE TO USE THE
CORRECT TYPE OR CALIBER OF AMMUNITION MAY CAUSE THE FIREARM TO JAM, FAIL TO FIRE OR EVEN GENERATE EXCESSIVE
PRESSURE WHICH CAN DAMAGE OR EVEN RUPTURE YOUR FIREARM, CAUSING PERSONAL INJURY, DEATH OR PROPERTY DAMAGE.

Your Safety responsibilitiy

You are responsible for selecting ammunition that meets industry standards and is appropriate in type and caliber for this firearm.

Locate the caliber designation marked on the left side of the upper receiver. This information indicates the ammunition caliber that should
be used in this firearm.

HANDLOADED OR RELOADED AMMUNITION

Warning:

NEVER USE NON-STANDARD, RELOADED OR ``HANDLOADED`` AMMUNITION WHICH HAS NOT BEEN
SUBJECTED TO INTERNAL BALLISTIC PRESSURE TESTING. RELOADED OR HANDLOADED AMMUNITION MAY HAVE MANY
MANUFACTURING AND QUALITY VARIABLES (SUCH AS THE TYPE AND AMOUNT OF GUN POWDER). ANY AMMUNITION THAT IS
IMPROPERLY MANUFACTURED, EVEN IN THE SLIGHTEST DEGREE, MAY FAIL TO FIRE OR MAY GENERATE EXCESSIVE INTERNAL
PRESSURES WHICH CAN DAMAGE OR EVEN RUPTURE THE FIREARM, CAUSING PERSONAL INJURY OR DEATH TO THE SHOOTER OR
THOSE IN THE IMMEDIATE VICINITY.

manual-8.576.80.02.indd 10

28.10.2011 07:07:43

Use only commercially manufactured ammunition with internal ballistic pressure which are in strict accordance with the specifications of
the Sporting Arms and Ammunition Manufacturers´ Institute (SAAMI). If you are uncertain, contact your ammunition supplier for verification.

C AMMUNITION SPECIFICS

In some cases, a round of ammunition not specified on your firearm may fit into the chamber. Firing ammunition not specified on your
firearm may cause it to rupture and cause serious injury or death to you or others.

Always inspect your ammunition before using it. Never use dirty, corroded or damaged ammunition which can lead to a burst cartridge
which may cause damage to the firearm and personal injury or death.

.22 L.R. caliber cartridges have a wide range of loads, from very weak for sport
attention: shooting
and maximum precision to very powerful for a high projectile velocity. To

ensure reliable operation, a semi-automatic firearm must be matched to a certain cartridge load. For this
reason the cal. .22 L.R. Colt M16 / M4 has been designed for high-quality standard ammunition and HV (High
Velocity) ammunition, and one can be sure of trouble-free operation only with these types. Please note that
these rifles are not designed for the use of cal. .22 extra long ammunition.

11
manual-8.576.80.02.indd 11

Your safety responsibility

Use only ammunition specifically recommended for your firearm.
Never mix ammunition.
Never use a cartridge not specifically designated for use in your firearm.
- Pressure from the wrong type of ammunition may exceed the capability of your firearm and may damage or even rupture your firearm.

28.10.2011 07:07:43

Warning:

fig. 1

Manual safety in
“SAFE” position

fig. 2

Manual safety in
“FIRE” position

fig. 3

Manual safety in
“SAFE” position

fig. 4

Manual safety in
“FIRE” position

Always leave the manual safety
engaged (on “SAFE”) until you intend to fire.

1 Manual Safety
Safe Position - turn the safety lever to the right so the

word “SAFE” is visible (fig. 1).
Fire Position - turn the safety lever to the left so the

word “FIRE” is visible (fig. 2).
On the right side of the firearm you also have an indicator for the
position of the manual safety (fig. 3 and 4).

Warning:

Operating instructions

Never rely solely on mechanical
features alone - always be extremely careful, use
safe gun handling practices, and avoid situations
which could lead to an accident.

Warning:

Always inspect the chamber of your firearm after the magazine has been removed from the
gun. Make sure that no cartridge is left in the chamber.

12
manual-8.576.80.02.indd 12

28.10.2011 07:07:50

2 Inspection

Warning:

Never put your hand in front of the muzzle.

Functional Inspection:
Bolt movement: Remove the magazine and retract the bolt by pulling back the charging handle. Release the charging handle
to return the bolt fully forward into battery.

Bolt catch: Insert the empty magazine, retract the bolt by pulling back the charging handle. The bolt locks back
in rearmost position.

Decocking: Make sure that the firearm is ON SAFE and unloaded (magazine removed, chamber cleared, empty chamber
indicator (blue tab) is installed, and barrel clear of any obstructions)!
Pull charging handle rearward and then release allowing it to freely move forward. Place safety in the OFF (Fire) position, make
sure the muzzle is pointed is a safe direction. Pull the trigger. The hammer drops to a de-cocked position.

InSpection

13
manual-8.576.80.02.indd 13

28.10.2011 07:07:51

3 Loading the firearm

Warning:

Before loading, make sure that the firearm is always pointed
in a safe direction, is ON SAFE, and is unloaded (magazine removed, chamber cleared,
empty chamber indicator (blue tab) is installed, and barrel clear of any obstructions).
Press magazine release and remove empty magazine (fig. 5). Use the side-mounted button to push
the follower down. Insert the cartridge under the magazine lips, at the same time pushing down the
follower (fig. 6). Do not use excessive force. Insert the loaded magazine until the magazine catch locks
it in position (fig. 7).

fig. 5
fig. 6

4 Loading the chamber with the first cartridge
Pick up the firearm with your shooting hand and point the muzzle in a safe direction. Use your other hand to
retract and release the bolt with the help of the charging handle (fig. 8). Never put your hand in front of the
muzzle. As the bolt travels forward it inserts the first round into the chamber. The hammer is now cocked.
Leave the safety in the safe position until you are ready to fire.

Loading the firearm

Warning:

Never put your hand in front of the muzzle.

Warning:

Always load a round into the chamber by feeding it from the
magazine. Failure to follow this warning can result in severe injury or death to
you or others. Never attempt to load the firearm by inserting a round into the open
ejection port.

fig. 7

14
manual-8.576.80.02.indd 14

28.10.2011 07:07:53

Colt M4/M16 cal. .22L.R. are designed so that they are able to

Warning: fire when the magazine is removed. Therefore, if the magazine

fig. 8

is removed from the firearm and there is a loaded round in the chamber, it will fire
if the trigger is pulled. After inserting a magazine, always test to make sure it is
locked in place by applying some removal pressure to the magazine.

Warning:

Your firearm is now ready to fire. Keep your finger off the
trigger and out of the trigger guard until you are ready to fire.

Grasp firearm with one hand on forearm and other hand on grip with index finger resting along outside of
trigger guard. Raise firearm and pull buttstock firmly into shoulder.
Aim at a safe target. Push the manual safety to the fire position. Squeeze the trigger slowly and maintain
the pressure until the round is fired.
Your firearm loads immediately after firing.
- You may continue to fire by pulling and fully releasing the trigger until the magazine is empty
- If you wish to stop, release trigger, remove finger from triggerguard, and set safety selector to “SAFE”
position. If you have fired the last round from the magazine, the bolt will be held in the rearmost position
so that the firearm can quickly be reloaded by replacing the magazine, or the chamber can be inspected
to ensure it is empty (fig. 9).

fig. 9

6 Decocking
-

If you decide not to fire after the hammer has been cocked or if you decide to suspend firing, keep the firearm pointed in a safe direction.
Remove your finger from within the trigger guard.
Place the manual safety in the “SAFE” position and remove the magazine.
Pull charging handle rearward to eject any remaining cartridge(s).
Make sure that the firearm is unloaded (magazine removed, chamber cleared, empty chamber indicator (blue tab) installed, and barrel
clear of any obstructions)!

Loading / Firing / decocking

5 Firing

15
manual-8.576.80.02.indd 15

28.10.2011 07:07:55

You must be certain there is no cartridge in the chamber or obstructions in the barrel. Remember that
any time you release the bolt while a magazine containing cartridges is in the firearm, you will have
reloaded the firearm and it will be capable of firing.
- Place the manual safety in the “FIRE” position (fig. 10).
- Squeeze trigger to decock the firearm.
- The firearm may now be transported safely.
Note: The external bolt catch lever does not function. The gun has an internal bolt catch. To put the
bolt into its forward position, first insert the simulating device (blue tab), then retract the charging
handle and release it.

fig. 10

Manual safety in
“FIRE” position

Warning:

Keep the firearm pointed in a safe direction when decocking.
Failure to do this can result in serious injury or death.

7 Firearm with empty magazine

Empty magazine / Unloading

After the last round has been fired, the bolt catch holds the bolt in the open position (fig. 11).
Place the manual safety in the “SAFE” position.
Continue shooting

Discontinue shooting

8 Unloading

fig. 11

- Replace the empty magazine with a full one. Pull bolt rearward and release with the
help of the charging handle (fig. 8), the bolt will travel forward and load the chamber
with the first round. Keep your firearm in your shooting hand, finger off the
trigger and pointed in a safe direction so that there is no danger to other persons.
- Remove magazine and inspect the chamber, to verify it does not contain any
ammunition (fig. 9). Close the bolt and decock hammer as described in section 6.

Point the muzzle in a safe direction. Remove the magazine. Ensure that the chamber is empty by pulling back the charging handle to visually
inspect the chamber (fig. 9). Place empty chamber indicator (blue tab) into the empty chamber (fig. 23). Keep firearm pointed in a safe direction.
Retract the charging handle so that the bolt moves into battery. Push the manual safety to the “fire” position (fig. 10) and squeeze trigger to
decock the firearm. The firearm may now be carried safely.

Warning:

Keep the firearm pointed in a safe direction when unloading. Failure to do this can result in
serious injury or death.
16

manual-8.576.80.02.indd 16

28.10.2011 07:07:57

9 Clearing misfires

Warning:

If your firearm gives any indication that it is not performing properly or the operation of
your firearm has changed “the way it feels or sounds”, stop firing. Make sure the firearm is pointed in a safe
direction, unload the firearm and have it inspected and test fired by a gunsmith qualified to perform service on
COLT M16/M4 rimfire rifles made by Carl Walther.
If a cartridge fails to fire, wait 30 seconds while keeping the muzzle pointed in a safe direction.
Keep your finger off the trigger and out of the trigger guard.
Place the manual safety in the “SAFE” position and remove the magazine.
Grasp the bolt with the charging handle and briskly pull it fully rearward to eject the misfired round. Check the barrel chamber
and bore visually for any obstructions. Never look down the barrel from the muzzle end.
- You must be certain there are no cartridges in the chamber or obstructions in the barrel. Remember that any time you release the bolt while
a magazine containing cartridges is in the firearm, you will have reloaded the firearm and it will be capable of firing.
Note: The forward assist plunger does not function. In case of feeding failures, retract the charging handle to extract the damaged round.

Warning:

Never try to use a misfired cartridge again.

10 Settings
10.1 Setting the dual aperture rear sight

fig. 12

fig. 13

The dual aperture rear sight can be adjusted for two target ranges
by flipping it foward or backward.
Short Range -

The larger aperture is used for 0 - 200 yards
range (0-200 meter) (fig. 12).
Normal Range - The smaler aperture is used for over 200 yards
(200 meters) range (fig. 13).

Clearing misfires / Settings

17
manual-8.576.80.02.indd 17

28.10.2011 07:07:58

10.2 Setting of the rear sight

fig. 14

fig. 15

fig. 16

fig. 17

The elevation is adjusted using the elevation knob below the rear
sight (fig. 14). Turning the knob adjusts elevation up or down.
Amount of adjustment is defined by a click when the knob is turned.
The windage is adjusted using the windage knob on the side of the
rear sight (fig. 15). Turning the knob adjusts for windage left or right.
Amount of adjustment is defined by a click when the knob is turned.
Note: Because this is a replica, the markings on the elevation and
windage knobs are not set for .22 LR ammunition.

10.3 Setting of the front sight post
The elevation is adjusted by pushing in the front sight post detent
near the front sight post (fig. 16) and simultaneously turning the front
sight post in desired position.The front sight post must be engaged
in one of the 4 detents (fig 17).
NOTE: Adjustment of the front sight post is for initial zeroing of the
rifle. For all future elevation adjustments use the rear sight.

fig. 18

10.4 Setting of the retractable stock (Models M4 Carbine; M4 OPS only)

Settings

On the Variants M4 Carbine and M4 OPS the buttstock can be adjusted in its length. Pushing the buttstock
latch allows the buttstock to be adjusted to various lengths (fig. 18).

18
manual-8.576.80.02.indd 18

28.10.2011 07:08:02

10.5 Setting of the bolt speed

fig. 19

The bolt speed can be adjusted for different ammunition requirements. To reach the screw for bolt speed
adjustment the gun has to be disassembled as described in Section 12 Field Stripping (fig.19). Only adjust
the bolt speed if problems are encountered when firing a different type of ammunition.
For high velocity ammunition, use the correct size Allen wrench (hex key) to increase the bolt speed by turning the screw clockwise (fig. 19).

11 Mounting an optical sight

settings / Mounting accesories

For standard ammunition, use the correct size Allen wrench (hex key) to decrease the bolt speed by turning
the screw counter clockwise (fig. 19). The screwhead must not rise out of, or be removed from the gun.

fig. 20

To mount an optical sight, the carry handle can be removed by loosing the nuts on the left side of the
carry handle (fig. 20). This will provide a mil-standard rail for mounting of optics.

19
manual-8.576.80.02.indd 19

28.10.2011 07:08:03

12 Field stripping

Warning:

Always follow the disassembly instructions exactly. Never do
anything beyond what you are specifically instructed to do in this manual. Never
alter or modify the parts in your firearm.

Warning:

Always wear eye protection that is specified for use with firearms, every time you handle your firearm for cleaning and maintenance.
fig. 21

Warning:

Prior to disassembly, place the manual safety in the safe
position, take out the magazine and check that the firearm is not loaded.
fig. 22

Field Stripping / Storage

To disassemble insert an empty magazine, pull back the bolt to its rearmost position with the charging
handle. Remove the magazine for further disassembly. Push the rear receiver pin out of the gun to the
right (fig. 21; 22). Do not use excessive force. There are 5 false/dummy pins (3 left side (fig. A), 2 right
side (fig.B)). Do not try to tap them out. Doing so will void your warrenty.
NOTE: Further disassembly is not necessary or recommended and will void your warranty.
When reassembling, hand-tighten the flash hider and then use the supplied wrench to further tighten by
only 1/4 turn.

fig. A

fig. B

Do not attempt to remove or tap on these five (5) false pins.
20

manual-8.576.80.02.indd 20

28.10.2011 07:08:07

13 Cleaning
In order to keep the firearm functional and to extend its service life, the firearm should be cleaned and
maintained at regular intervals.

Warning:

Before cleaning, make sure that the firearm is always pointed in a safe direction, is ON SAFE ,
and is unloaded (magazine removed, chamber cleared, empty chamber indicator (blue tab) is installed, and barrel
clear of any obstructions).
Remove fouling from breech, magazine lips, follower, and receiver with a brush and a cloth. Clean the barrel with bore solvent and a brush and
then dry it with cleaning patches; always begin at the chamber. Repeat until barrel is clean. Apply a thin coat of oil to all metal parts.
Reassemble firearm and check for proper function.
-

Verify gun is ON SAFE.
Insert EMPTY magazine and retract charging handle so that bolt assembly remains in open position.
Remove magazine.
Visually inspect to verify that no ammo remains anywhere in the rifle.
Loosen compensator only two revolutions
Remove rear receiver pin so that upper receiver pivots upward
Thoroughly clean the bolt assembly area with a brush and cloth (aerosol gun scrubber works great) to remove powder residue and debris.
Clean the barrel with bore solvent utilizing a flexible cleaning rod inserted trough breech end of barrel (where bullet seats).

cleaning

NOTE: Cleaning the barrel from the muzzle end requires a bore brush that does NOT exceed 1-inch in the length. Using a brush
exceeding this length will result in the brush being lodged in the breech area.

21
manual-8.576.80.02.indd 21

28.10.2011 07:08:07

Apply 2 drops of gun oil to the main spring.
Apply 1 drop of gun oil to the extractor.
Apply 1 drop of gun oil to each end of firing pin assembly.
Reassemble rifle by installing the rear pin.
Hand-tighten the compensator and the further tighten 1/4 turn using the supplied wrench.
Wipe down exterior surface of rifle with gun oil.
Insert the blue tab (empty chamber indicator), pull the charging handle rearward, then release to close the bolt assembly.

Mounting Accesories / Cleaning / Storage

Note: Do not apply more oil to the recoil spring, extractor or firing pin assembly than is mentioned above. Doing so will result in an
increased accumulation of powder residue which can lead to misfires and jamming issues.

fig. 23

14 Storage

Warning:

Never leave a loaded firearm unattended!

Always keep and store your firearm in an unloaded condition with the safety in the “SAFE” position. Keep
the firearm and ammunition away from children and unauthorized persons. Firearms should be stored
separately from ammunition. Always store your firearm with the empty chamber indicator (blue tab) in
the chamber to make sure no cartridge is loaded (fig. 23).

22
manual-8.576.80.02.indd 22

28.10.2011 07:08:08

15 Repair
Do not return defective or damaged product to the dealer. If your firearm needs repair, call Umarex USA (479) 646-4210 and ask for the Service
Department or visit www.Colt22Rimfire.com.

Warning:

Only an authorized and qualified gunsmith should inspect and repair your firearm!

16 Warranty
Limited One Year Warranty
This product is warranted to the original owner for 1 year from date of purchase against defects in material and workmanship and is not transferable.

WHat iS nOt COvered
Parts, labor, and shipping charges related to to Umarex USA for defective product and damages caused by abuse or failure to perform normal
maintenance as well as any other expense. Consequential damages, or incidental expenses, including damage to property. Umarex USA will not
be responsible for unauthorized adjustments or modifications, use of defective or improper ammunition, corrosion, criminal misuse, negligence,
resale, and/or use under the influence of drugs or alcohol. Some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you. Umarex USA reserves the right to determine what constitues ordinary wear
and tear.
WarrantY ClaiMS
Warranty Claims and Repair for U.S. customers. Call Umarex USA (479)-646-4210 and ask for the Service Department. If it is determined a
return is necessary, you will be issued a Return Authorization Number. Write this number boldly on the box and return the product prepaid to
Umarex USA. Your name, address, phone number and a note with the model number, serial number, and explanation of the defect found must be
included in the package. A copy of the original purchase receipt must accompany the return.

Repair / warranty

WHat iS COvered
Replacement parts and labor.

23
manual-8.576.80.02.indd 23

28.10.2011 07:08:08

iMplied WarrantieS
Any implied warranties, including the implied warranties of merchantability and fitness for a particular purpose, are limited in duration to 1 year
from date of retail purchase. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE
LIMITATIONS MAY NOT APPLY TO YOU. TO THE EXTENT ANY PROVISION OF THIS WARRANTY IS PROHIBITED BY FEDERAL STATE, OR MUNICIPAL
LAW WHICH CANNOT BE PREEMPTED, IT SHALL NOT BE APPLICABLE. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO
HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE AND COUNTRY TO COUNTRY.
UNDER NO CIRCUMSTANCES SHALL UMAREX USA and carl walther GMBH BE RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES WITH RESPECT TO ECONOMIC LOSS, INJURY, DEATH OR PROPERTY DAMAGE, WHETHER AS A RESULT OF
BREACH OF THIS WARRANTY, NEGLIGENCE OR OTHERWISE.
Note: All liability is excluded in the event that the instructions and warnings in
this manual are not observed.
Shipping guidelines
•
•
•
•
•
•

Warranty

•
•
•
•
•

Ensure that the firearm is unloaded.
Do not attempt to ship a firearm via US Postal Service; only federally licensed firearm dealers may ship a firearm by US Postal Service.
DO NOT SHIP ANY AMMUNITION.
Enclose a letter which includes your full name and address (no P.O. Boxes, please), daytime telephone number, e-mail
address, the serial number of the firearm, and details of the problem experienced (stating the brand and type of ammunition
used when the problem occurred) or work desired.
Record the serial number before shipping, in case you wish to check on the repair status of your firearm.
Please remove all custom parts and accessories, such as stocks, special sights and scopes, or slings from your firearm
before returning.
Place the firearm in its original case or in a similarly secure container and pack it securely.
The package must NOT bear any markings which indicate the identity of the contents.
It is recommended that shipments be insured by the owner, since Umarex USA will accept no responsibility for loss or damage in transit.
It is most important that you comply with federal, state, and local laws and regulations. The following guidelines are meant
to help, but you must seek assistance from the appropriate authorities if necessary.
If your firearm must be replaced, it may be necessary to ship the replacement to a dealer rather than directly to you. You
will be requested to furnish a signed FFL (Federal Firearms License) from your dealer in such an instance.

manual-8.576.80.02.indd 24

28.10.2011 07:08:08

17 Technical Data
M16 SPR

M4 Carbine

M4 OPS

caliber

.22 L.R.

action

blowback

trigger

single stage trigger

6.6 - 9.9 lbs
(3500 - 4500g)

magazine capacity

30 rounds

dimensions (L/H/W)

39.8 / 9.1 / 2.6 inch
(1010 / 230 / 65 mm)

31.1-34.4 / 9.1 / 2.6 inch
(790-875 / 230 / 65 mm)

barrel length

21.2 inch
(538 mm)

16.1 inch
(409 mm)

sight radius

20.1 inch
(510 mm)

20.5 inch
(520 mm)

14.8 inch
(375 mm)

0.06 / 0.2 inch
(1.65 / 5.25 mm)

0.06 / 0.19 inch
(1.65 / 4.9 mm)

0.06 / 0.2 inch
(1.65 / 5.25 mm)

front sight width

0.08 inch
(2 mm)

width w/out mag

6.5 lbs
(2950g)

6.0 lbs
(2750g)

5.9 lbs
(2700g)

9.2 ounce
(260g)

trigger pull

diameter of rear sight
aperture

magazine weight (empty)

technical data

M16 Rifle

25
manual-8.576.80.02.indd 25

28.10.2011 07:08:08

18 Exploded view/ Parts
18.1 Exploded view

Explode view
26
manual-8.576.80.02.indd 26

28.10.2011 07:08:13

18.2 Parts

11
12
13
14
15
16
17
18
19
20
21
22
23
24

26
27
28

576.71.04.1
576.70.03.1
576.30.08.1
576.30.07.1
576.30.06.1
576.11.03.1
576.11.02.1
576.11.05.1
576.11.04.1
576.11.01.1
576.11.07.1
576.11.06.1
2245110
576.12
576.70.26.3
576.50.02
576.51.02
576.52.02
576.55.02
576.50.11.1
576.51.11.1
2245113
2245112
2245116
2245115
512.50.06.2
576.70.20
2245120

manual-8.576.80.02.indd 27

Bolt
Carry Handle
Carry Handle M4 Carbine, M16 Rifle
Tactical Rear Sight
Sight Base M4 OPS
Rear Sight
Flip up rear sight
Pin
Knob Elevation
Rear Sight Ball Bearing
Spring
Bearing Screw
Ejection Port Cover
Clamping Bar M4 Carbine,
M16 Rifle
Clamping Bar M4 OPS
Thumb Nut
Spring
Pin
Plunger
Buttstock Tube Lock
Nut
Screw
Washer
Carbine Receiver Extension
Screw
Receiver Extension Plate
Buttstock M4 Carbine, M4 OPS
Buttstock M16 Rifle, M16 SPR
Pin
Barrel M4 Carbine, M4 OPS
Barrel M16 Rifle, M16 SPR
Barrel M16 Rifle, M4 CQB
Barrel M4 NEC
Handguard M4 Carbine
Handguard M16 Rifle
RIS M16 SPR
RIS M4 OPS
Flash Hider
Fake silencer
Rubber Ring
Front Sight
Flip up front sight

29 576.50.12.3
30 576.50.10.1
576.51.10.1
576.52.04.1
31 576.50.07.1
576.52.06.1
32 576.50.03
576.51.03
576.52.03
33 576.20.27.3
34 576.40.09.1
35 576.30.01.1
36 576.40.18.1
37 576.40.05.0
38 576.40.03
40 576.40.07.1
41 576.40.13.1
42 576.40.06.3
43 576.20.39.1
45 576.40.17.0
46 506.40.05.1
47 576.40.19.1
48 576.20.36.0
51 576.40.01.1
52 576.40.14.1
53 576.40.11.0
54 2245102
2245100
2771691
55 576.10.11.1
56 576.40.15.3
57 576.40.02.0
58 576.10.09.0
59 576.10.10.1
60 576.20.16.3
61 576.20.17.0
62 576.20.02.1
63 576.20.09.1
64 576.20.28.3
65 576.20.18.3
66 576.40.08.3
67 576.20.29.1
68 576.20.04

Pin
Handguard Cap M4 Carbine
Handguard Cap M16 Rifle
RIS Barrel Nut M4 OPS, M16 SPR
Deltaring M4 Carbine, M16 Rifle
RIS Screw M4 OPS, M16 SPR
Barrel Sleeve M4 Carbine, M4 OPS
Barrel Sleeve M16 Rifle, M16 SPR
Barrel Sleeve M4 CQB
Spring Loaded Thrust Pad
Screw
Upper Receiver
Adjustment pin
Charging Handle
Slide
Bolt
Main Spring
Screw
Screw
Extractor
Bolt
Spring
Ejector
Slide Housing Right
Spring
Slide Catch
Magazine 30 rd
Magazine 10 rd
Magazine 20 rd
Pin
Pin
Slide Housing Left
Bolt Catch Lever
Pin
Screw Nut
Safety Button
Trigger Housing Right
Bumper
Roll Pin
Pin
Pin
Spring
Trigger sear arm

70
71
73
74
75
76
77
78
80
81
82
84
86
87
88
90
91
92
93
94
95
96
97
98
99
100
102
103
105
106
107
108
109
110
111
113
114
115

577.20.20
576.20.15.3
576.20.07
576.20.01.1
576.20.11.0
576.20.13.1
577.20.06.0
570.20.23.3
576.20.40.1
576.20.14.1
570.20.18.1
576.20.21.1
576.20.12.1
576.20.03.0
576.20.41.1
576.20.10.0
576.20.08.0
576.10.01.1
576.13.01.1
576.10.02.1
576.10.04.1
576.10.05.1
576.10.12.3
576.10.03.3
576.10.06.1
576.10.08.3
576.10.07.3
576.20.24.3
576.20.22.1
512.20.42.1
576.10.13.1
576.70.18.1
576.40.22.3
576.40.21.1
576.40.20.1
578.20.06.1
576.40.25.1
577.20.07.0
576.90

Hammer
Pin
Safety
Trigger Housing Left
Magazine Catch Button
Spring
Disconnector
Screw Nut
Spring
Hammer Spring Receptor
Spring
Spring
Spring
Trigger
Pin
Magazine Catch
Safety Lever
Lower Receiver M4 Carbine, M4 OPS
Lower Receiver M16 Rifle, M16 SPR
Trigger Guard
Pin
Spring
Screw
Pin
Pistol Grip
Lock Washer
Screw
Allen Wrench SW 4
Allen Wrench SW 4
Simulating Device
Receiver Extension Screw Nut
Base Spring
Pin
Spring
Charging Handle Latch
Safety detent pin
Spring for extractor
Wiper for disconnector
Accessories set

Designation

1 576.70.02.1
2 2245117
576.70.01.1
2245121
576.71.01.1
3 576.70.05
2245122
4 576.70.15.3
5 576.70.12.1
6 576.70.10.3
7 576.70.14.1
8 576.70.17.3
9 576.30.02.1
10 576.70.04.1

27
28.10.2011 07:08:13

19 Variants and accessories
19.1 Variants

M16 Rifle

• Adjustable Front Sight (Elevation)
• Adjustable Rear Sight (Windage, Elevation)
• 21.2” Barrel Length

M16 SPR

variants

• Rail Interface System
• Detachable Flip Up Rear Sight
• Adjustable Flip Up Front Sight (Elevation)
• Adjustable Flip Up Rear Sight (Windage)
• 21.2” Barrel Length

M4 Carbine

• Retractable Buttstock
• Adjustable Front Sight (Elevation)
• Adjustable Rear Sight (Windage, Elevation)
• 16.1” Barrel Length

M4 OPS

• Retractable Buttstock
• Rail Interface System
• Detachable Rear Sight
• Adjustable Front Sight (Elevation)
• Adjustable Rear Sight (Windage, Elevation)
• 16.1” Barrel Length

28
manual-8.576.80.02.indd 28

28.10.2011 07:08:31

19.2 Accessories
M4/M16 Magazine
10 Round 2245100
30 Round 2245102

M4/M16 Flip Up
Front Sight
2245120

M4/M16 Metal
Compensator
2245116

Walther Xenon
Tactical Flashlight
2252516

M4/M16 Flip Up
Rear Sight

Walther Cord Switch
for Flashlight

2245122

Walther Flashlight
Mount

2252517

2252518

M4/M16 Magazine
Speed Holster
2245103

M4 Special Force
Crane Stock
2245111

M4/M16 Tactical
Rear Sight

M4/M16 Carry
Handle

2245121

2245117

Walther PS 55 Scope
2300580

Walther PS 22 Red
Dot Sight
2300577

M4 Retractable
Stock
M4/M16 Quad RIS
for M4 Carbine
for M16 Rifle

2245112
2245113

Accessories

2245110

Walther RS 55 4x32
Compact Tactical Scope with
Illuminated Reticle
2245132

29
manual-8.576.80.02.indd 29

28.10.2011 07:08:38

Notes

NOTES
30
manual-8.576.80.02.indd 30

28.10.2011 07:08:38

NOTES

Notes

31
manual-8.576.80.02.indd 31

28.10.2011 07:08:38

COLT M4/M16 .22 Rimfire Rifles
made by Carl Walther - Germany
under license from New Colt Holding Corp.
Distribution and repair service by:

This INSTRUCTION MANUAL should always accompany the firearm and be
transferred with it upon change of ownership or when presented to another person.
A copy of the INSTRUCTION MANUAL is available FREE upon request from:

contact

Umarex Usa Inc.
www.umarexusa.com
www.colt22rimfire.com
Sales + Warranty Service
7700 Chad Colley Boulevard / Fort Smith, AR 72916 / USA Phone: 479-646-4210 / Fax: 479-646-4206
All technical changes and modifications reserved.
8.576.80.02 rev. N
Oktober 2011

manual-8.576.80.02.indd 32

28.10.2011 07:08:38

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 5.0-c060 61.134777, 2010/02/12-17:32:00
Instance ID                     : uuid:c6ba5b00-b220-4995-bb0b-06f3289e7f0b
Document ID                     : adobe:docid:indd:1e5c9f48-376a-11e0-b7ae-bf78b4dbd5b2
Original Document ID            : adobe:docid:indd:1e5c9f48-376a-11e0-b7ae-bf78b4dbd5b2
Rendition Class                 : proof:pdf
Version ID                      : 1
Derived From Instance ID        : 1e5c9f47-376a-11e0-b7ae-bf78b4dbd5b2
Derived From Document ID        : adobe:docid:indd:4f1efb17-a39c-11df-878a-b0d8dd0622c3
History Action                  : saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved
History Instance ID             : xmp.iid:4EB83AAA2264E011B96580700FC6E341, xmp.iid:4FB83AAA2264E011B96580700FC6E341, xmp.iid:A21FF69A2364E011B96580700FC6E341, xmp.iid:81DF9D702B64E011B96580700FC6E341, xmp.iid:0BA9001E2C64E011B96580700FC6E341, xmp.iid:0CA9001E2C64E011B96580700FC6E341, xmp.iid:2ED3FF0CD264E011AAA2B9EBFF071284, xmp.iid:2FD3FF0CD264E011AAA2B9EBFF071284, xmp.iid:ECBBCCAFDF64E011AAA2B9EBFF071284, xmp.iid:EDBBCCAFDF64E011AAA2B9EBFF071284, xmp.iid:EEBBCCAFDF64E011AAA2B9EBFF071284, xmp.iid:76A2CC7ECC65E01194EBD624DAFA99E5, xmp.iid:F614642F20A6E0119B3BF1D0734394EC, xmp.iid:F714642F20A6E0119B3BF1D0734394EC, xmp.iid:DB8EAEF321A6E0119B3BF1D0734394EC, xmp.iid:2CC97AF822A6E0119B3BF1D0734394EC, xmp.iid:2DC97AF822A6E0119B3BF1D0734394EC, xmp.iid:DF512EE4AADAE011A37C816C8899C20C, xmp.iid:07D4CB03AEDAE011A37C816C8899C20C, xmp.iid:0B0F3AD6AFDAE011A37C816C8899C20C, xmp.iid:B0CF2ADFB0DAE011A37C816C8899C20C, xmp.iid:808C7724B1DAE011A37C816C8899C20C, xmp.iid:097FEC3EB4DAE011A37C816C8899C20C, xmp.iid:F43A5439A300E1118E3E81091C90B7EC, xmp.iid:48978767A500E1118E3E81091C90B7EC, xmp.iid:8C1813D42101E111A98696ECD51DE4BC
History When                    : 2011:04:11 12:01:26+02:00, 2011:04:11 12:01:26+02:00, 2011:04:11 12:08:10+02:00, 2011:04:11 13:04:15+02:00, 2011:04:11 13:09:06+02:00, 2011:04:11 13:11:45+02:00, 2011:04:12 08:56:54+02:00, 2011:04:12 09:16:55+02:00, 2011:04:12 10:34:31+02:00, 2011:04:12 10:35:10+02:00, 2011:04:12 10:38:02+02:00, 2011:04:13 14:49:39+02:00, 2011:07:04 11:29:58+02:00, 2011:07:04 11:30:52+02:00, 2011:07:04 11:42:37+02:00, 2011:07:04 11:49:54+02:00, 2011:07:04 11:53:45+02:00, 2011:09:09 08:13:52+02:00, 2011:09:09 08:36:14+02:00, 2011:09:09 08:49:16+02:00, 2011:09:09 08:56:41+02:00, 2011:09:09 08:58:37+02:00, 2011:09:09 09:20:50+02:00, 2011:10:27 15:54:44+02:00, 2011:10:27 16:10:20+02:00, 2011:10:28 07:01+02:00
History Software Agent          : Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0
History Changed                 : /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata
Create Date                     : 2011:10:28 07:07:41+02:00
Modify Date                     : 2011:10:28 07:08:39+02:00
Metadata Date                   : 2011:10:28 07:08:39+02:00
Creator Tool                    : Adobe InDesign CS5 (7.0)
Page Image Page Number          : 1, 2
Page Image Format               : JPEG, JPEG
Page Image Width                : 256, 256
Page Image Height               : 256, 256
Page Image                      : (Binary data 10696 bytes, use -b option to extract), (Binary data 10704 bytes, use -b option to extract)
Doc Change Count                : 206
Format                          : application/pdf
Title                           : manual-8.576.80.02.indd
Producer                        : Adobe PDF Library 9.9
Trapped                         : False
GTS PDFX Version                : PDF/X-4
Page Count                      : 32
Creator                         : Adobe InDesign CS5 (7.0)

EXIF Metadata provided by EXIF.tools

Manual 8.576.80.02 Colt M4 M16 22 Rimfire 10R11

Navigation menu

Versions of this User Manual:

Views

Navigation