Manual SDK Versao Zk Teco
User Manual:
Open the PDF directly: View PDF 
.
Page Count: 264
| Download | |
| Open PDF In Browser | View PDF |
ZKTeco Standalone SDK Development
Manual
Version: 2.1, Rev. A.2
Date: 2018.04.25
Copyright
©ZKTECO CO., LTD. 2018.All rights reserved.
This document may not be reproduced, disseminated or republished in any form without the prior
written permission of ZKTECO.
Release history
Date
2018-01-01
2018-04-25
Version
2.0, Rev. A.1
2.1, Rev. A.2
Change
New release version
Distribution group of International
General Service Office
Contacts
No. 8, Room 2001, Chengyi North
Street, The Third Period Of Software
Park, Xiamen, Fujian, China
Tel:+86 592-7791134
For additional offices around the world, see www.zkteco.com corporate offices.
Contents
1 SDK Description ............................................................................................................................................... 1
2 Quick Start ......................................................................................................................................................... 2
2.1 Terms ...................................................................................................................................................... 2
2.2 Common Processes ................................................................................................................................. 3
2.2.1 Downloading Attendance Records .............................................................................................. 3
2.2.2 Downloading Operation Records ................................................................................................ 4
2.2.3 Setting Access Control................................................................................................................. 5
2.2.4 Downloading User Information, or Fingerprint Templates ......................................................... 6
2.2.5 Receiving Real-time Events ........................................................................................................ 7
2.2.6 Enrolling Users Online (Uploading Information,and Fingerprint Templates of Users) .............. 8
2.2.7 Uploading Short Messages .......................................................................................................... 9
3 Related Attributes ............................................................................................................................................ 10
3.1 AccGroup ............................................................................................................................................. 10
3.2 AccTimeZones...................................................................................................................................... 10
3.3 BASE64 ................................................................................................................................................ 10
3.4 CardNumber ......................................................................................................................................... 11
3.5 CommPort............................................................................................................................................. 11
3.6 ConvertBIG5 ........................................................................................................................................ 11
3.7 PINWidth .............................................................................................................................................. 11
3.8 GetStrCardNumber ............................................................................................................................... 12
3.9 SetStrCardNumber ............................................................................................................................... 12
3.10 IsNewFirmwareMachine .................................................................................................................... 13
3.11 GetDeviceFirmwareVersion ............................................................................................................... 14
4 Real-time Event Functions .............................................................................................................................. 15
4.1 Obtaining Real-Time Events ................................................................................................................ 15
4.1.1 RegEvent ................................................................................................................................... 15
4.1.2 ReadRTLog................................................................................................................................ 16
4.1.3 GetRTLog .................................................................................................................................. 16
4.2 Real-Time Events ................................................................................................................................. 17
4.2.1 OnConnected ............................................................................................................................. 17
4.2.2 OnDisConnected........................................................................................................................ 18
4.2.3 OnAlarm .................................................................................................................................... 18
I
4.2.4 OnDoor ...................................................................................................................................... 19
4.2.5 OnAttTransaction ...................................................................................................................... 19
4.2.6 OnAttTransactionEx .................................................................................................................. 21
4.2.7 OnEnrollFinger .......................................................................................................................... 22
4.2.8 OnEnrollFingerEx ..................................................................................................................... 23
4.2.9 OnDeleteTemplate ..................................................................................................................... 24
4.2.10 OnFinger .................................................................................................................................. 24
4.2.11 OnFingerFeature ...................................................................................................................... 25
4.2.12 OnHIDNum ............................................................................................................................. 25
4.2.13 OnKeyPress ............................................................................................................................. 26
4.2.14 OnNewUser ............................................................................................................................. 26
4.2.15 OnVerify .................................................................................................................................. 26
4.2.16 OnWriteCard............................................................................................................................ 27
4.2.17 OnEmptyCard .......................................................................................................................... 28
4.2.18 OnEMData............................................................................................................................... 28
5 Common Functions ......................................................................................................................................... 30
5.1 Device Connection Functions ............................................................................................................... 30
5.1.1 Connect_Net .............................................................................................................................. 30
5.1.2 Connect_Com ............................................................................................................................ 30
5.1.3 Connect_USB ............................................................................................................................ 31
5.1.4 Connect_P4P ............................................................................................................................. 32
5.1.5 Disconnect ................................................................................................................................. 33
5.2 Data Management Functions ................................................................................................................ 33
5.2.1 Attendance Record Data ............................................................................................................ 33
5.2.1.1 ReadGeneralLogData ..................................................................................................... 33
5.2.1.2 ReadAllGLogData .......................................................................................................... 34
5.2.1.3 ReadTimeGLogData ....................................................................................................... 34
5.2.1.4 ReadNewGLogData........................................................................................................ 35
5.2.1.5 GetGeneralLogData ........................................................................................................ 36
5.2.1.6 GetAllGLogData ............................................................................................................ 39
5.2.1.7 GetGeneralLogDataStr ................................................................................................... 41
5.2.1.8 GetGeneralExtLogData .................................................................................................. 42
5.2.1.9 SSR_GetGeneralLogData ............................................................................................... 44
5.2.1.10 ClearGLog .................................................................................................................... 46
5.2.1.11 DeleteAttlogBetweenTheDate ...................................................................................... 47
II
5.2.1.12 DeleteAttlogByTime..................................................................................................... 48
5.2.2 Operation Record Data .............................................................................................................. 49
5.2.2.1 ReadSuperLogData......................................................................................................... 49
5.2.2.2 ReadAllSLogData ........................................................................................................... 49
5.2.2.3 GetSuperLogData ........................................................................................................... 50
5.2.2.4 GetAllSLogData ............................................................................................................. 53
5.2.2.5 ClearSLog ....................................................................................................................... 55
5.2.2.6 GetSuperLogData2 ......................................................................................................... 56
5.2.3 User Information Functions ....................................................................................................... 58
5.2.3.1 ReadAllUserID ............................................................................................................... 58
5.2.3.2 EnableUser ..................................................................................................................... 58
5.2.3.3 SSR_EnableUser ............................................................................................................ 59
5.2.3.4 SetUserInfoEx ................................................................................................................ 60
5.2.3.5 GetAllUserID.................................................................................................................. 61
5.2.3.6 GetAllUserInfo ............................................................................................................... 62
5.2.3.7 GetUserInfoEx ................................................................................................................ 63
5.2.3.8 DeleteUserInfoEx ........................................................................................................... 64
5.2.3.9 SSR_GetAllUserInfo ...................................................................................................... 65
5.2.3.10 GetUserInfo .................................................................................................................. 66
5.2.3.11 GetUserInfoByPIN2 ..................................................................................................... 67
5.2.3.12 GetUserInfoByCard ...................................................................................................... 68
5.2.3.13 GetUserIDByPIN2........................................................................................................ 69
5.2.3.14 GetPIN2 ........................................................................................................................ 70
5.2.3.15 SSR_GetUserInfo ......................................................................................................... 70
5.2.3.16 SetUserInfo ................................................................................................................... 72
5.2.3.17 SSR_SetUserInfo .......................................................................................................... 73
5.2.3.18 ModifyPrivilege ............................................................................................................ 74
5.2.4 Registration Data Functions (Including Both User Information and Fingerprint) .................... 75
5.2.4.1 GetEnrollData ................................................................................................................. 75
5.2.4.2 SetEnrollData.................................................................................................................. 76
5.2.4.3 DeleteEnrollData ............................................................................................................ 77
5.2.4.4 SSR_DeleteEnrollData ................................................................................................... 78
5.2.4.5 SSR_DeleteEnrollDataExt.............................................................................................. 79
5.2.4.6 GetEnrollDataStr ............................................................................................................ 80
5.2.4.7 SetEnrollDataStr ............................................................................................................. 81
III
5.2.5 Fingerprint Template Functions ................................................................................................. 82
5.2.5.1 ReadAllTemplate ............................................................................................................ 82
5.2.5.2 SSR_GetUserTmp .......................................................................................................... 83
5.2.5.3 SSR_GetUserTmpStr...................................................................................................... 84
5.2.5.4 SSR_SetUserTmp ........................................................................................................... 84
5.2.5.5 SSR_SetUserTmpStr ...................................................................................................... 85
5.2.5.6 DelUserTmp ................................................................................................................... 86
5.2.5.7 SSR_DelUserTmp .......................................................................................................... 87
5.2.5.8 SSR_SetUserTmpExt ..................................................................................................... 88
5.2.5.9 SSR_DelUserTmpExt ..................................................................................................... 88
5.2.5.10 SetUserTmp .................................................................................................................. 89
5.2.5.11 SetUserTmpStr ............................................................................................................. 90
5.2.5.12 SetUserTmpEx.............................................................................................................. 91
5.2.5.13 SetUserTmpExStr ......................................................................................................... 92
5.2.5.14 GetUserTmp ................................................................................................................. 93
5.2.5.15 GetUserTmpStr............................................................................................................. 94
5.2.5.16 GetUserTmpEx ............................................................................................................. 95
5.2.5.17 GetUserTmpExStr ........................................................................................................ 96
5.2.5.18 GetFPTempLength........................................................................................................ 97
5.2.5.19 GetFPTempLengthStr ................................................................................................... 97
5.2.5.20 FPTempConvert ............................................................................................................ 98
5.2.5.21 FPTempConvertStr ....................................................................................................... 99
5.2.5.22 FPTempConvertNew .................................................................................................. 100
5.2.5.23 FPTempConvertNewStr.............................................................................................. 100
5.2.6 Face Template Functions ......................................................................................................... 101
5.2.6.1 SetUserFace .................................................................................................................. 101
5.2.6.2 GetUserFace ................................................................................................................. 102
5.2.6.3 DelUserFace ................................................................................................................. 103
5.2.6.4 GetUserFaceStr............................................................................................................. 104
5.2.6.5 SetUserFaceStr ............................................................................................................. 105
5.2.7 User Verify Functions .............................................................................................................. 106
5.2.7.1 SetUserVerifyStyle ....................................................................................................... 106
5.2.7.2 GetUserVerifyStyle ....................................................................................................... 107
5.2.8 Shortcut Keys Functions .......................................................................................................... 108
5.2.8.1 SSR_SetShortkey.......................................................................................................... 108
IV
5.2.8.2 SSR_GetShortkey ......................................................................................................... 110
5.2.8.3 EnableCustomizeAttState ............................................................................................. 111
5.2.8.4 SetCustomizeAttState ................................................................................................... 112
5.2.8.5 DelCustomizeAttState .................................................................................................. 113
5.2.8.6 GetAllSFIDName ......................................................................................................... 114
5.2.8.7 GetShortkey .................................................................................................................. 115
5.2.8.8 SetShortkey................................................................................................................... 116
5.2.9 Work Code Functions .............................................................................................................. 118
5.2.9.1 SetWorkCode ................................................................................................................ 118
5.2.9.2 GetWorkCode ............................................................................................................... 119
5.2.9.3 SSR_GetWorkCode ...................................................................................................... 120
5.2.9.4 SSR_SetWorkCode ....................................................................................................... 120
5.2.9.5 SSR_DeleteWorkCode ................................................................................................. 121
5.2.9.6 SSR_ClearWorkCode ................................................................................................... 122
5.2.9.7 DeleteWorkCode........................................................................................................... 122
5.2.9.8 ClearWorkCode ............................................................................................................ 123
5.2.9.9 SSR_GetWorkCodeIDByName .................................................................................... 123
5.2.10 SMS Functions ...................................................................................................................... 124
5.2.10.1 SetSMS ....................................................................................................................... 124
5.2.10.2 SetUserSMS ............................................................................................................... 125
5.2.10.3 SSR_SetUserSMS ...................................................................................................... 126
5.2.10.4 GetSMS ...................................................................................................................... 127
5.2.10.5 DeleteSMS. ................................................................................................................. 128
5.2.10.6 DeleteUserSMS .......................................................................................................... 128
5.2.10.7 SSR_DeleteUserSMS ................................................................................................. 129
5.2.10.8 ClearUserSMS ............................................................................................................ 130
5.2.10.9 ClearSMS ................................................................................................................... 131
5.2.11 Holiday Functions.................................................................................................................. 131
5.2.11.1 SetHoliday .................................................................................................................. 131
5.2.11.2 GetHoliday.................................................................................................................. 132
5.2.11.3 SSR_GetHoliday......................................................................................................... 133
5.2.11.4 SSR_SetHoliday ......................................................................................................... 134
5.2.12 DST Functions ....................................................................................................................... 135
5.2.12.1 SetDaylight ................................................................................................................. 135
5.2.12.2 GetDaylight ................................................................................................................ 135
V
5.2.13 System Data Management Functions .................................................................................... 136
5.2.13.1 ClearKeeperData ........................................................................................................ 136
5.2.13.2 ClearData .................................................................................................................... 137
5.2.13.3 GetDataFile................................................................................................................. 138
5.2.13.4 SendFile ...................................................................................................................... 139
5.2.13.5 ReadFile ...................................................................................................................... 140
5.2.13.6 RefreshData ................................................................................................................ 140
5.2.14 User Photo & Attendance Photo ............................................................................................ 141
5.2.14.1 UploadUserPhoto........................................................................................................ 141
5.2.14.2 DownloadUserPhoto................................................................................................... 142
5.2.14.3 DeleteUserPhoto ......................................................................................................... 143
5.2.14.4 GetAllUserPhoto ........................................................................................................ 143
5.2.14.5 GetPhotoNamesByTime ............................................................................................. 144
5.2.14.6 GetPhotoByName ....................................................................................................... 145
5.2.14.7 GetPhotoCount. .......................................................................................................... 146
5.2.14.8 ClearPhotoByTime ..................................................................................................... 147
5.2.15 Bell Functions ........................................................................................................................ 148
5.2.15.1 GetBellSchDataEx ...................................................................................................... 148
5.2.15.2 SetBellSchDataEx ...................................................................................................... 149
5.2.15.3 GetDayBellSchCount ................................................................................................. 151
5.2.15.4 GetMaxBellIDInBellSchData ..................................................................................... 151
5.2.15.5 ReadAllBellSchData................................................................................................... 152
5.2.15.6 GetEachBellInfo ......................................................................................................... 153
5.2.16 UserValidDate Functions ....................................................................................................... 154
5.2.16.1 SetUserValidDate........................................................................................................ 154
5.2.16.2 GetUserValidDate ....................................................................................................... 155
5.2.17 Personalise Functions ............................................................................................................ 157
5.2.17.1 UploadTheme ............................................................................................................. 157
5.2.17.2 UploadPicture ............................................................................................................. 157
5.2.17.3 DownloadPicture ........................................................................................................ 158
5.2.18 APP Info Functions................................................................................................................ 159
5.2.18.1 GetAllAppFun ............................................................................................................ 159
5.2.18.2 GetAllRole .................................................................................................................. 160
5.2.18.3 GetAppOfRole ............................................................................................................ 161
5.2.18.4 GetFunOfRole ............................................................................................................ 161
VI
5.2.18.5 SetPermOfAppFun ..................................................................................................... 162
5.2.18.6 DeletePermOfAppFun ................................................................................................ 163
5.2.18.7 IsUserDefRoleEnable ................................................................................................. 164
5.2.19 Template Integration Functions ............................................................................................. 165
5.2.19.1 SSR_SetDeviceData ................................................................................................... 165
5.2.19.2 SSR_GetDeviceData .................................................................................................. 166
5.2.19.3 SSR_GetDeviceDataCount ......................................................................................... 167
5.2.19.4 SSR_DeleteDeviceData .............................................................................................. 168
5.2.19.5 Variable description : BiometricType ......................................................................... 168
5.2.19.6 Variable description : BiometricVersion ..................................................................... 169
5.2.19.7 Variable description : BiometricMaxCount ................................................................ 169
5.2.19.8 Variable description : BiometricUsedCount ............................................................... 170
5.3 Access Control Functions(Time Slot, Group, Open Door Combination) ........................................... 170
5.3.1 GetUserGroup.......................................................................................................................... 170
5.3.2 SetUserGroup .......................................................................................................................... 171
5.3.3 GetTZInfo ................................................................................................................................ 172
5.3.4 SetTZInfo ................................................................................................................................ 173
5.3.5 GetUnlockGroups .................................................................................................................... 174
5.3.6 SetUnlockGroups .................................................................................................................... 175
5.3.7 SSR_SetUnLockGroup............................................................................................................ 176
5.3.8 SSR_GetUnLockGroup ........................................................................................................... 177
5.3.9 GetGroupTZs ........................................................................................................................... 178
5.3.10 SetGroupTZs ......................................................................................................................... 179
5.3.11 GetGroupTZStr ...................................................................................................................... 180
5.3.12 SetGroupTZStr ...................................................................................................................... 180
5.3.13 SSR_SetGroupTZ .................................................................................................................. 181
5.3.14 SSR_GetGroupTZ ................................................................................................................. 182
5.3.15 GetUserTZs ........................................................................................................................... 184
5.3.16 SetUserTZs ............................................................................................................................ 185
5.3.17 GetUserTZStr ........................................................................................................................ 185
5.3.18 SetUserTZStr ......................................................................................................................... 186
5.3.19 ACUnlock .............................................................................................................................. 188
5.3.20 GetACFun.............................................................................................................................. 188
5.3.21 GetDoorState ......................................................................................................................... 189
5.3.22 UseGroupTimeZone .............................................................................................................. 190
VII
5.3.23 TurnOffAlarm ........................................................................................................................ 190
5.4 Device Management Functions .......................................................................................................... 191
5.4.1 IsTFTMachine ......................................................................................................................... 191
5.4.2 GetDeviceStatus ...................................................................................................................... 192
5.4.3 GetDeviceInfo ......................................................................................................................... 193
5.4.4 SetDeviceInfo .......................................................................................................................... 196
5.4.5 SetDeviceTime ........................................................................................................................ 197
5.4.6 SetDeviceTime2 ...................................................................................................................... 198
5.4.7 GetDeviceTime ........................................................................................................................ 199
5.4.8 GetSerialNumber ..................................................................................................................... 200
5.4.9 GetProductCode ...................................................................................................................... 200
5.4.10 GetFirmwareVersion.............................................................................................................. 201
5.4.11 GetSDKVersion ..................................................................................................................... 202
5.4.12 GetDeviceIP .......................................................................................................................... 202
5.4.13 SetDeviceIP ........................................................................................................................... 203
5.4.14 GetDeviceMAC ..................................................................................................................... 204
5.4.15 SetDeviceMAC...................................................................................................................... 205
5.4.16 GetWiegandFmt ..................................................................................................................... 205
5.4.17 SetWiegandFmt ..................................................................................................................... 206
5.4.18 GetCardFun ........................................................................................................................... 207
5.4.19 SetDeviceCommPwd ............................................................................................................. 208
5.4.20 SetCommPassword ................................................................................................................ 208
5.4.21 QueryState ............................................................................................................................. 209
5.4.22 GetVendor .............................................................................................................................. 210
5.4.23 GetDeviceStrInfo ................................................................................................................... 210
5.4.24 GetPlatform ........................................................................................................................... 211
5.4.25 ReadAOptions ....................................................................................................................... 212
5.4.26 GetSysOption ........................................................................................................................ 213
5.4.27 SetSysOption ......................................................................................................................... 214
5.4.28 GetDeviceStatusEx ................................................................................................................ 214
5.5 Others ................................................................................................................................................. 215
5.5.1 Device Control Functions ........................................................................................................ 215
5.5.1.1 ClearAdministrators...................................................................................................... 215
5.5.1.2 EnableDevice ................................................................................................................ 216
5.5.1.3 EnableClock ................................................................................................................. 217
VIII
5.5.1.4 DisableDeviceWithTimeOut......................................................................................... 217
5.5.1.5 PowerOffDevice ........................................................................................................... 218
5.5.1.6 RestartDevice................................................................................................................ 219
5.5.2 Online Registration Functions ................................................................................................. 219
5.5.2.1 StartEnroll..................................................................................................................... 219
5.5.2.2 StartEnrollEx ................................................................................................................ 220
5.5.2.3 StartVerify..................................................................................................................... 221
5.5.2.4 StartIdentify .................................................................................................................. 222
5.5.2.5 CancelOperation ........................................................................................................... 222
5.5.3 Card Operation Functions........................................................................................................ 223
5.5.3.1 WriteLCD ..................................................................................................................... 223
5.5.3.2 ClearLCD ..................................................................................................................... 224
5.5.3.3 WriteCard ..................................................................................................................... 224
5.5.3.4 EmptyCard .................................................................................................................... 226
5.5.4 Others ...................................................................................................................................... 226
5.5.4.1 GetLastError ................................................................................................................. 226
5.5.4.2 GetHIDEventCardNumAsStr ....................................................................................... 229
5.5.4.3 CaptureImage................................................................................................................ 230
5.5.4.4 UpdateFirmware ........................................................................................................... 231
5.5.4.5 BeginBatchUpdate ........................................................................................................ 231
5.5.4.6 BatchUpdate ................................................................................................................. 232
5.5.4.7 CancelBatchUpdate ...................................................................................................... 233
5.5.4.8 PlayVoice ...................................................................................................................... 233
5.5.4.9 PlayVoiceByIndex ........................................................................................................ 234
5.5.4.10 ReadAttRule ............................................................................................................... 235
5.5.4.11 SaveTheDataToFile .................................................................................................... 235
5.5.4.12 ReadTurnInfo .............................................................................................................. 236
5.5.4.13 SSR_OutPutHTMLRep .............................................................................................. 237
5.5.4.14 SendFileByType ......................................................................................................... 239
5.5.4.15 SetCommProType ....................................................................................................... 239
5.5.4.16 SetCommProType ....................................................................................................... 240
5.5.4.17 GetConnectStatus ....................................................................................................... 240
5.5.4.18 SetDeviceTableData ................................................................................................... 241
5.5.4.19 SearchDevice .............................................................................................................. 242
6 FAQs .............................................................................................................................................................. 244
IX
6.1 How to Download Attendance Records? ............................................................................................ 244
6.2 How to Create a User Online? ............................................................................................................ 244
6.3 How to Import or Download Data from USB Disk? .......................................................................... 244
6.4 How to Use Biokey to Write the Collected Fingerprint Templates Offline? ...................................... 247
6.5 How to Obtain All Information of All Users? .................................................................................... 247
6.6 How to Connect to the Device? .......................................................................................................... 247
6.7 Password Is Invalid After SetUserInfo Is Used. ................................................................................. 248
6.8 How to Convert an Online Template into an Offline Template? ........................................................ 248
6.9 Demo Program Fails to Connect to the Device. ................................................................................. 248
6.10 Offline Fingerprint Device Keeps Working After Being Connected. ............................................... 249
6.11 Illegal Characters Are Displayed or Screen Display Is Abnormal After Non-English Names or Short
Messages Are Uploaded to the Device. .................................................................................................... 249
6.12 Card Management Problems ............................................................................................................ 249
6.13 Firewall or Router Traversal ............................................................................................................. 250
6.14 Difference between ZKFinger10.0 and ZKFinger9.0 and Comparison between Templates ............ 250
6.15 Uploading a Large Capacity of Fingerprints .................................................................................... 250
6.16 Differences between High-speed Upload and Ordinary Upload ...................................................... 250
6.17 How to Determine Whether the Device Uses ZKFinger10.0 or ZKFinger9.0? ............................... 251
6.18 How to Upload, Download, and Delete ZKFinger10.0 Templates? ................................................. 251
6.19 How to Upload, Download, and Delete ZKFinger9.0 Templates? ................................................... 252
6.20 How to Download a Face Template? ................................................................................................ 252
X
1 SDK Description
The offline communication SDK is an interface for data communication with offline fingerprint
devices, access control devices, and RFID card devices. It can be used to conveniently manage
user information and fingerprints, download attendance records, operation records, user
information, and fingerprint templates, set devices, and configure access control. The SDK is
used to:
1. Download attendance records.
2. Upload and download user information, card information, fingerprints, and face information.
3. Set access control rules of access control devices.
4. Set device time, match thresholds, etc.
5. Trigger various events of devices in real time, for example, fingerprint verification.
6. Directly enroll users online.
7. Set SMS and work code (available only on devices that support this function) of users.
8. Set personalized prompt tones, function keys, etc.
1
2 Quick Start
2.1 Terms
1.
Real-time event
After the SDK and the device communicate with each other successfully, some operations
on the device (for example, connecting to the device, verifying a user, and enrolling a user)
trigger corresponding events in real time, and data is transmitted to the PC (host computer).
The triggered events are called real-time events. Users can monitor device states and user
operations in real time through real-time events.
2.
FP
Shortened form of "fingerprint".
3.
Fingerprint algorithm
A fingerprint algorithm refers to the algorithm used to generate and verify fingerprint
templates. At present, ZKFinger 9.0 is the latest fingerprint algorithm used by ZKSoftware
black & white devices. It is a high-speed algorithm with higher performance. For details, see
FAQs.
4.
High-speed buffer
A high-speed buffer refers to the memory requested by the SDK on a PC during usage. In
the data upload or download process, data is first saved in the buffer before being processed.
5.
Time slot, group, open door combination
These three terms are the most important concepts of access control.
A time slot is a time range. A time slot includes the time information of one week, and a time
range is specified for each day of this week. For example, the following expression indicates
a time range from 00:00 to 22:11 in each day of one week:
00002211000022110000221100002211000022110000221100002211. Generally, 50 time
slots can be set in the device.
A group is a collection. When many users have the same access control privileges, these
users can be added to the same group and use the group time slot. Then, time slots can be set
for the group.
An open door combination refers to the groups that are required for unlock. If the open door
combination contains only one group, it indicates that the door is opened when any of the
users in this group passes verification. If the open door combination contains two or more
groups, the door is opened only after all groups pass verification. For example, an open door
combination contains groups A and B, the door is opened only after a member of group A
and a member of group B pass verification.
The following figure shows the relationship of the three concepts:
2
Open door
combination
User
Personal time
slot
Belonging
group
Is group time
slot used?
Group time slot
6.
Operation record
An operation record, also called management record, is a record generated when users or
administrators operate on the device, for example, powering on/off the device and enrolling
a user.
2.2 Common Processes
For details, see the descriptions of the demo program.
2.2.1 Downloading Attendance Records
Start
Connect the device
(Connect_Net or others)
Read all ATT records from
device and write into buffer
(ReadGeneralLogData)
Is ATT records
read successfully from buffer?
(SSR_GetGeneralLogData)
N
Y
Store data
End
Note
BW device use GetGeneralLogData instead of SSR_GetGeneralLogData.
3
2.2.2 Downloading Operation Records
Start
Connect the device
(Connect_Net or others)
Read all operation records
from device and write into
buffer
(ReadSuperLogData)
Is operation records read
successfully from buffer?
(GetSuperLogData)
N
Y
Store data
Note
Applicable to BW, TFT and IFACE devices.
4
End
2.2.3 Setting Access Control
Start
Connect the device
(Connect_Net or others)
Define time zone
(SetTZInfo)
Is group time zone used?
(UseGroupTimeZone or
GetUserTZStr)
Define group time zone
(SetGroupTZStr)
Y
N
Set user group
(SetUserGroup)
Set personal time
zone
(SetUserTZStr)
Set open door combination
(SSR_SetUnlockGroup)
End
Note
BW device use SetUnlockGroups instead of SSR_SetUnlockGroup.
5
2.2.4 Downloading User Information, or Fingerprint Templates
The left diagram shows the process of downloading the information of all users. The right
diagram shows the process of downloading the information of a specified user.
Start
Start
Connect the device
(Connect_Net or others)
Connect the device
(Connect_Net or others)
Read all user information
and write it to PC buffer
(ReadAllUserID)
Download
user information
(SSR_GetUserInfo )
Read all fingerprints and
write them into PC buffer
（ReadAllTemplate）
Y
Is user
information read
successfully from PC
buffer?
(SSR_GetAllUserInfo)
Obtain card number of the user
(attribute:Cardnumber or
GetStrCardNumber)
Y
N
Obtain card number of the user
(attribute:Cardnumber or
GetStrCardNumber)
N
Obtain fingerprint
template of the user
(SSR_GetUserTmpStr
or GetUserTmpExStr)
Obtain fingerprint
template of the user
(SSR_GetUserTmpStr
or GetUserTmpExStr)
End
End
Note
BW device use GetAllUserInfo instead of SSR_GetAllUserInfo, GetUserTmpStr instead of
SSR_GetUserTmpStr, GetUserInfo instead of SSR_GetUserInfo.
6
2.2.5 Receiving Real-time Events
Real-time events can be received in two modes. The second mode is recommended.
Start
Start
Connect the device
(Connect_Net or others)
Connect the device
(Connect_Net or others)
N
Is real-time
read successfully
from PC buffer
(ReadRTLog)
Register real-time
events to be triggered
(Regevent)
Y
Obtain real-time
events from buffer
and trigger them
(GetRTLog)
End
Note
Applicable to BW, TFT and IFACE devices
7
2.2.6 Enrolling Users Online (Uploading Information,and Fingerprint Templates
of Users)
There are two online user enrollment modes. The left diagram shows the process in which the
device accesses the enrollment interface to enroll a user after being connected. The right diagram
shows the process of creating a user on the device and uploading the card number, password, and
fingerprint information for the user (that is, enrolling a card user, a password user, and a
fingerprint user).
Start
Start
Connect the device
(Connect_Net or others)
Connect the device
(Connect_Net or others)
Start online
enrollment
(StartEnroll)
Register card
Set card number of the user
(attribute:cardnumber or
SetStrCardNumber)
Is enrollment
end?
Y
Enable device to
wait for user
verification
(startIdentify)
Register user and password
Upload user information to device. Create the user
if the user does not exist
(SSR_SetUserInfo)
Register fingerprint
Upload fingerprint template to specified user
(SSR_SetUserTmpStr or
SetUserTmpExStr)
Note
End
End
BW device use
SetUserInfo instead of SSR_SetUserInfo, SetUserTmpStr instead of SSR_SetUserTmpStr.
8
2.2.7 Uploading Short Messages
Start
Connect the device
(Connect_Net or others)
Define SMS
(SetSMS)
Is personal
SMS used?
Y
Allocate SMS to user
(SSR_SetUserSMS)
N
End
Note
BW device use SetUserSMS instead of SSR_SetUserSMS.
9
3 Related Attributes
3.1 AccGroup
To set or query the group to which a specified user belongs.
Type: LONG
See also
Attention
If this attribute is set before uploading the user, set the group to which this user belongs when
invoking SetUserInfo. Otherwise, the default group 1 takes effect. This attribute is configurable.
Note
Applicable to BW, TFT and IFACE devices
3.2 AccTimeZones
To set the usage period of a user.
Type: LONG
See also
Attention
1. If this attribute is set before uploading the user, set the usage period of the user when invoking
SetUserInfo.
2.This attribute is of the LONG* type. It is a LONG-type array with the subscript 3. This attribute
is configurable.
Note
Applicable to BW, TFT and IFACE devices
3.3 BASE64
To set the code type.
Type: LONG
See also
Attention
If this attribute is set to True, the SDK will output a Base64 code when outputting the character
string template. Otherwise, it will output a hexadecimal code.
Note
Applicable to BW, TFT and IFACE devices
10
3.4 CardNumber
To set or read the card number of a user.
Type: LONG
See also
Attention
If this attribute cannot be used, invoke GetStrCardnumber and SetStrCardnumber. This attribute
is configurable.
Note
Applicable to BW, TFT and IFACE devices
3.5 CommPort
To set a serial port number, or a port number used for RS485 connection.
Type: LONG
See also
Attention
The attribute is of the LONG type and is configurable.
Note
Applicable to BW, TFT and IFACE devices
3.6 ConvertBIG5
To convert simplified Chinese characters into traditional Chinese characters.
Type: LONG
See also
Attention
1. If the value of this attribute is set to True, the SDK will automatically convert simplified
Chinese characters into traditional Chinese characters for further development. This function is
invalid on a multi-language machine. Therefore, do not set this attribute.
2.This attribute is invalid on a multi-language machine and later versions. Therefore, do not set
this attribute. You do not need to modify this attribute in versions later than ZEM100 5.22 and
ZEM200 5.30.
Note
Applicable to BW, TFT and IFACE devices
3.7 PINWidth
To label the maximum length of the user code, which is an Arabic numeral.
11
Type: LONG
See also
Attention
The attribute is of the LONG type and is read-only.
Note
Applicable to BW, TFT and IFACE devices
3.8 GetStrCardNumber
VARIANT_BOOL GetStrCardNumber(BSTR* ACardNumber)
To query the value of the SDK attribute cardnumber. You can invoke this function to query the
card number of a user after obtaining the information about this user.
Parameters
Parameter description:
name
type
param direction
description of param
ACardNumber
BSTR*
[out]
Card number
Returns
Value description:
name type
True
description of value
BOOL Function execution success
False BOOL Function execution failure
See also
Attention
Note
Applicable to BW
3.9 SetStrCardNumber
VARIANT_BOOL SetStrCardNumber(BSTR ACardNumber)
To set the value of the SDK attribute cardnumber. Before setting user information, you are
advised to invoke this function to set the card number of the user.
Parameters
12
Parameter description:
name
type param direction description of param
ACardNumber BSTR
[in]
Card number
Returns
Value description:
name type
True
description of value
BOOL Function execution success
False BOOL Function execution failure
See also
Attention
Note
Applicable to BW
3.10 IsNewFirmwareMachine
VARIANT_BOOL IsNewFirmwareMachine(LONG dwMachineNumber)
To identify whether the current device firmware are new architecture firmware.
Parameters
Parameter description:
name
type param direction
dwMachineNumber LONG
description of param
[in]
Machine ID
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
13
Attention
Note
Apply to BW, TFT, IFACE devices
3.11 GetDeviceFirmwareVersion
VARIANT_BOOL GetDeviceFirmwareVersion(LONG dwMachineNumber, BSTR* strVersion)
To query the firmware version.
Parameters
Parameter description:
name
type
param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
strVersion
BSTR*
[out]
Firmware version of the machine
Returns
Value description:
name
type
description of value
True
BOOL
Function execution success
False
BOOL
Function execution failure
See also
Attention
Note
This interface is applicable to the new architecture firmware.
14
4 Real-time Event Functions
4.1 Obtaining Real-Time Events
4.1.1
RegEvent
VARIANT_BOOL RegEvent(LONG dwMachineNumber, LONG EventMask)
To register a real-time event to be triggered.
Parameters
Parameter description:
name
type param direction description of param
dwMachineNumber LONG
EventMask
LONG
[in]
Machine ID
[in]
Event ID
Returns
Value description:
name type
True
description of value
BOOL Function execution success
False BOOL Function execution failure
See also
Attention
The event IDs are described as follows:
1 OnAttTransaction OnAttTransactionEx
2(1<<1) OnFinger
4(1<<2) OnNewUser
8(1<<3) OnEnrollFinger OnEnrollFingerEx
16(1<<4) OnKeyPress
256(1<<7) OnVerify
512(1<<8) OnFingerFeature
1024(1<<9) OnDoor OnAlarm
2048(1<<10) OnHIDNum
4096(1<<11) OnWriteCard
8192(1<<12) OnEmptyCard
16384(1<<13) OnDeleteTemplate
15
To register multiple real-time events, perform the OR operation for the binary event IDs. To
register all real-time events, set EventMask to 65535.
Note
Applicable to BW, TFT and IFACE devices
4.1.2
ReadRTLog
VARIANT_BOOL ReadRTLog(LONG dwMachineNumber)
To read real-time events to the buffer of the PC.
Parameters
Parameter description:
name
type param direction description of param
dwMachineNumber LONG
[in]
Machine ID
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
Attention
This function can be used together with GetRTLog to actively obtain real-time events from the
machine after the machine is connected successfully.
Note
Applicable to BW, TFT and IFACE devices
4.1.3
GetRTLog
VARIANT_BOOL GetRTLog(LONG dwMachineNumber)
To get a real-time event from the buffer of the PC and trigger this event.
Parameters
Parameter description:
name
type param direction description of param
16
dwMachineNumber LONG
[in]
Machine ID
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
This function can be used together with ReadRTLog to actively obtain real-time events from the
machine after the machine is connected successfully.
Note
Applicable to BW, TFT and IFACE devices
4.2 Real-Time Events
4.2.1
OnConnected
OnConnected(LONG MachineNumber)
To trigger this event when the machine is connected successfully.
Parameters
Parameter description:
name
type param direction description of param
MachineNumber LONG
[in]
Machine ID
Returns
None
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
17
4.2.2
OnDisConnected
OnDisConnected(LONG MachineNumber)
To trigger this event when the machine is disconnected.
Parameters
Parameter description:
name
type param direction
MachineNumber LONG
description of param
[in]
Machine ID
Returns
None
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
4.2.3
OnAlarm
OnAlarm (LONG AlarmType, LONG EnrollNumber, LONG Verified)
To trigger this event when the machine raises an alarm.
Parameters
Parameter description:
name
type
param direction
description of param
AlarmType
LONG
[in]
Alarm type
EnrollNumber
LONG
[in]
User ID
Verified
LONG
[in]
Whether to perform verification
Returns
None
See also
Attention
1. Alarm Type: alarm type. The value 55 indicates a tamper alarm, 58 misoperation alarm, 32
duress alarm, and 34 passback alarm.
2.EnrollNumber: user ID. The value is 0 if the alarm is a tamper alarm, misoperation alarm, or
18
duress key alarm. The value is the user ID if the alarm is another type of duress alarm or a
passback alarm.
3.Verified: whether to perform verification. The value is 0 when the alarm is a tamper or
misoperation alarm, and is 1 if the alarm is of other types.
Note
Applicable to BW, TFT and IFACE devices
4.2.4
OnDoor
OnDoor (LONG EventType)
To trigger this event when the machine opens the door.
Parameters
Parameter description:
name
type
param direction
description of param
EventType
LONG
[in]
Door opening type
Returns
None
See also
Attention
EventType: specifies the door opening type. The value 4 indicates that the door is not closed
properly or has been opened, 53 indicates an exit button, 5 indicates that the door has been closed,
and 1 indicates that the door is opened unexpectedly.
Note
Applicable to BW, TFT and IFACE devices
4.2.5
OnAttTransaction
OnAttTransaction(LONG EnrollNumber, LONG IsInValid, LONG AttState, LONG
VerifyMethod, LONG Year, LONG Month, LONG Day, LONG Hour, LONG Minute, LONG
Second, LONG WorkCode)
To trigger this event when the verification is passed.
Parameters
Parameter description:
name
type
param direction
description of param
19
EnrollNumber
LONG
[in]
Alarm type
IsInValid
LONG
[in]
Whether the record is valid
AttState
LONG
[in]
Attendance status
VerifyMode
LONG
[in]
Verification mode of the record
Year
LONG
[in]
Year
Month
LONG
[in]
Month
Day
LONG
[in]
Date
Hour
LONG
[in]
Hour
Minute
LONG
[in]
Minute
Returns
None
See also
Attention
1. The VerifyMode parameter specifies the verification mode. The values are described as follows:
Under normal conditions:
0 indicates password verification, 1 fingerprint verification, and 2 card verification.
Under multiple verification modes:
FP_OR_PW_OR_RF 0
FP 1
PIN 2
PW 3
RF 4
FP_OR_PW 5
FP_OR_RF 6
PW_OR_RF 7
PIN_AND_FP 8
FP_AND_PW 9
FP_AND_RF 10
PW_AND_RF 11
FP_AND_PW_AND_RF 12
PIN_AND_FP_AND_PW 13
FP_AND_RF_OR_PIN 14
2.The AttState parameter specifies the attendance status. The values are described as follows:
0-Check-In Default
1-Check-Out
20
2-Break-Out
3-Break-In
4-OT-In
5-OT-Out
Note
Applicable to BW
4.2.6
OnAttTransactionEx
OnAttTransactionEx(BSTR EnrollNumber, LONG IsInValid, LONG AttState, LONG
VerifyMethod, LONG Year, LONG Month, LONG Day, LONG Hour, LONG Minute, LONG
Second, LONG WorkCode)
To trigger this event when the verification is passed.
Parameters
Parameter description:
name
type
param direction
description of param
EnrollNumber
BSTR
[in]
Alarm type
IsInValid
LONG
[in]
Whether the record is valid
AttState
LONG
[in]
Attendance status
VerifyMode
LONG
[in]
Verification mode of the record
Year
LONG
[in]
Year
Month
LONG
[in]
Month
Day
LONG
[in]
Date
Hour
LONG
[in]
Hour
Minute
LONG
[in]
Minute
Second
LONG
[in]
Second
WorkCode
LONG
[in]
Work code
Returns
None
See also
Attention
21
1. The VerifyMode parameter specifies the verification mode. The values are described as follows:
Under normal conditions:
0 indicates password verification, 1 fingerprint verification, and 2 card verification.
Under multiple verification modes:
FP_OR_PW_OR_RF 0
FP 1
PIN 2
PW 3
RF 4
FP_OR_PW 5
FP_OR_RF 6
PW_OR_RF 7
PIN_AND_FP 8
FP_AND_PW 9
FP_AND_RF 10
PW_AND_RF 11
FP_AND_PW_AND_RF 12
PIN_AND_FP_AND_PW 13
FP_AND_RF_OR_PIN 14
2.The AttState parameter specifies the attendance status. The values are described as follows:
0-Check-In Default
1-Check-Out
2-Break-Out
3-Break-In
4-OT-In
5-OT-Out
The WorkCode parameter specifies the work code. If the machine does not support the work code,
0 is returned.
Note
Applicable to BW, TFT and IFACE devices
4.2.7
OnEnrollFinger
OnEnrollFinger(LONG EnrollNumber, LONG FingerIndex, LONG ActionResult, LONG
TemplateLength)
To trigger this event when registering a fingerprint.
Parameters
Parameter description:
name
type
param direction
22
description of param
EnrollNumber
LONG
[in]
ID of the user whose fingerprint is to be
registered
FingerIndex
LONG
[in]
Index of the fingerprint to be registered
ActionResult
LONG
[in]
Operation result. The value is 0 if the
operation succeeds and is larger than 0 if
the operation fails.
TemplateLength
LONG
[in]
Length of the fingerprint template
Returns
None
See also
Attention
Use under certain circumstances of 9-digit job width and 5-digit job width
Note
Applicable to BW,IFACE devices
4.2.8
OnEnrollFingerEx
OnEnrollFinger(BSTR EnrollNumber, LONG FingerIndex, LONG ActionResult, LONG
TemplateLength)
To trigger this event when registering a fingerprint.
Parameters
Parameter description:
name
type
param direction
description of param
EnrollNumber
BSTR
[in]
ID of the user whose fingerprint is to be
registered
FingerIndex
LONG
[in]
Index of the fingerprint to be registered
ActionResult
LONG
[in]
Operation result. The value is 0 if the
operation succeeds and is larger than 0 if
the operation fails.
TemplateLength
LONG
[in]
Length of the fingerprint template
Returns
None
23
See also
Attention
Note
Applicable to TFT and IFACE devices
4.2.9
OnDeleteTemplate
OnDeleteTemplate(LONG EnrollNumber, LONG FingerIndex)
To trigger this event when deleting a fingerprint template on the machine.
Parameters
Parameter description:
name
type
param direction
description of param
EnrollNumber
LONG
[in]
ID of the user to which the fingerprint
template to be deleted belongs
FingerIndex
LONG
[in]
Index of the fingerprint template to be
deleted
Returns
None
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
4.2.10
OnFinger
OnFinger()
To trigger this message when a fingerprint is scanned by the machine.
Parameters
None
Returns
None
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
24
4.2.11
OnFingerFeature
OnFingerFeature(LONG Score)
To trigger this message if a finger is pressed onto the fingerprint reader when registering user
fingerprints.
Parameters
Parameter description:
name
type
param direction
description of param
Score
LONG
[in]
Quality score of the fingerprint
Returns
None
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
4.2.12
OnHIDNum
OnHIDNum (LONG CardNumber)
To trigger this message when punching a card.
Parameters
Parameter description:
name
type
param direction
description of param
CardNumber
LONG
[in]
Card number
Returns
None
See also
Attention
The card can be an ID card or HID card. For an MIFARE card, this event will be triggered only
when it is used as an ID card.
Note
Applicable to BW, TFT and IFACE devices
25
4.2.13
OnKeyPress
OnKeyPress(LONG Key)
To trigger this message when a key is available.
Parameters
Parameter description:
name
type
param direction
description of param
Key
LONG
[in]
Key value
Returns
None
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
4.2.14
OnNewUser
OnNewUser (LONG EnrollNumber)
To trigger this message when a new user is registered successfully.
Parameters
Parameter description:
name
type
param direction
description of param
EnrollNumber
LONG
[in]
ID of the newly registered user
Returns
None
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
4.2.15
OnVerify
OnVerify (LONG UserID)
26
To trigger this message during user verification.
Parameters
Parameter description:
name
type
param direction
description of param
UserID
LONG
[in]
ID of the user to be verified
Returns
None
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
4.2.16
OnWriteCard
OnWriteCard (LONG EnrollNumber, LONG ActionResult, LONG Length)
To trigger this event when the machine writes data to a card.
Parameters
Parameter description:
name
type
param direction
description of param
EnrollNumber
LONG
[in]
User ID of the card to which data is to
be written
ActionResult
LONG
[in]
Result of the write operation. The value
0 indicates operation success and other
values indicate operation failure.
Length
LONG
[in]
Total size of the data written to the
card
Returns
None
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
27
4.2.17
OnEmptyCard
OnEmptyCard (LONG ActionResult)
To trigger this event when the machine writes data to a card.
Parameters
Parameter description:
name
ActionResult
type
LONG
param direction
description of param
[in]
Result of the clear operation. The value
0 indicates operation success and other
values indicate operation failure.
Returns
None
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
4.2.18
OnEMData
OnEMData (LONG DataType, LONG DataLen, CHAR* DataBuffer)
To trigger this event when the machine sends an unknown event to the SDK.
Parameters
Parameter description:
name
type
param direction
description of param
DataType
LONG
[in]
Event type
DataLen
LONG
[in]
Total data length
DataBuffer
CHAR*
[in]
Data
Returns
None
See also
Attention
Note
28
Applicable to BW, TFT and IFACE devices
29
5 Common Functions
5.1 Device Connection Functions
5.1.1
Connect_Net
VARIANT_BOOL Connect_Net(BSTR IPAdd, LONG Portl)
To connect to the machine to set up a network connection with the machine by using an IP
address.
Parameters
Parameter description:
name type param direction
description of param
IPAdd BSTR
[in]
IP address of the machine
Portl LONG
[in]
Port number of the machine
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
The default port number for connecting to the machine is 4370.
Note
Applicable to BW, TFT and IFACE devices
5.1.2
Connect_Com
VARIANT_BOOL Connect_Com(LONG ComPort, LONG MachineNumber, LONG BaudRate)
To connect to the machine through a serial port, that is, the RS232 RS485 port.
Parameters
Parameter description:
30
name
type param direction
description of param
ComPort
LONG
[in]
Serial port of the PC to be connected to
the machine
MachineNumber
LONG
[in]
Machine ID
BaudRate
LONG
[in]
Baud rate
Returns
Value description:
name
type
description of value
True
BOOL
Function execution success
False
BOOL
Function execution failure
See also
Attention
This function is also used when a machine communicates with a PC by using a USB client. The
precondition is that the USB client drive is installed beforehand to simulate a virtual serial port,
which can be viewed in the device manager on the PC. The program can also search for this
serial port. For details, see the description of USBClient in DEMO.
Note
Applicable to BW, TFT and IFACE devices
5.1.3
Connect_USB
VARIANT_BOOL Connect_USB(LONG MachineNumber)
To connect to the machine through a USB port.
Parameters
Parameter description:
name
type
param direction
description of param
MachineNumber
LONG
[in]
Machine ID
31
Returns
Value description:
name
type
description of value
True
BOOL
Function execution success
False
BOOL
Function execution failure
See also
Connect_Com
Attention
This function applies only to H series machines and cannot be used in the communication
conducted through a USB client. For details about the communication conducted through a USB
client, see the description of Connect_Com.
Note
Applicable to BW
5.1.4
Connect_P4P
VARIANT_BOOL Connect_P4P(BSTR uid)
To connect P2P devices.
Parameters
Parameter description:
name type param direction description of param
uid
BSTR
[in]
Machine ID
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
32
uid is the factory number, used as the identify ID of the P2P devices
Note
Applicable to some P2P devices, such as the K Pro series attendace machine
5.1.5
Disconnect
Disconnect()
To disconnect from the machine to release relevant resources.
Parameters
None
Returns
None
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
5.2 Data Management Functions
5.2.1
Attendance Record Data
5.2.1.1 ReadGeneralLogData
VARIANT_BOOL ReadGeneralLogData(LONG dwMachineNumber)
To read attendance records to the internal buffer of the PC. The function is the same as
ReadAllGLogData.
Parameters
Parameter description:
name
type param direction description of param
dwMachineNumber LONG
[in]
Machine ID
Returns
Value description:
name type
True
description of value
BOOL Function execution success
33
False BOOL Function execution failure
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
5.2.1.2 ReadAllGLogData
VARIANT_BOOL ReadAllGLogData(LONG dwMachineNumber)
To read attendance records to the internal buffer of the PC. The function is the same as
ReadGeneralLogData.
Parameters
Parameter description:
name
type param direction description of param
dwMachineNumber LONG
[in]
Machine ID
Returns
Value description:
name type
True
description of value
BOOL Function execution success
False BOOL Function execution failure
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
5.2.1.3 ReadTimeGLogData
VARIANT_BOOL ReadTimeGLogData(LONG dwMachineNumber, BSTR sTime, BSTR eTime)
To download attendance records based on the specified start time and end time, accurate to
seconds.
Parameters
Parameter description:
34
name
type
param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
sTime
BSTR
[in]
Start time in the format of YYYY-MM-DD
hh:mm:ss
eTime
BSTR
[in]
End time in the format of YYYY-MM-DD
hh:mm:ss
Returns
Value description:
name type
True
description of value
BOOL Function execution success
False BOOL Function execution failure
See also
Attention
Note
This interface is applicable to the new architecture firmware.
5.2.1.4 ReadNewGLogData
VARIANT_BOOL ReadNewGLogData(LONG dwMachineNumber)
To download the new generated attendance records.
Parameters
Parameter description:
name
type param direction description of param
dwMachineNumber LONG
[in]
Machine ID
Returns
Value description:
name type
description of value
35
True
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
This interface is applicable to the new architecture firmware.
5.2.1.5 GetGeneralLogData
VARIANT_BOOL GetGeneralLogData(LONG dwMachineNumber, LONG*
dwTMachineNumber, LONG* dwEnrollNumber, LONG* dwEMachineNumber, LONG*
dwVerifyMode, LONG* dwInOutMode, LONG* dwYear, LONG* dwMonth, LONG* dwDay,
LONG* dwHour, LONG* dwMinute)
To read attendance records from the internal buffer one by one. Before using this function,
execute ReadAllGLogData or ReadGeneralLogData to read the attendance records from the
machine to the internal buffer of the PC. Each time this function is executed, the pointer moves to
the next attendance record. This function is the same as GetAllGLogData. They differ only in the
interface name for compatibility.
Parameters
Parameter description:
description of
name
type param direction
param
dwMachineNumber
LONG
[in]
Machine ID
[out]
Pointer that points
to the LONG
variable. Its value
is the machine ID of
an attendance
record.
LONG*
[out]
Pointer that points
to the LONG
variable. Its value
is the user ID of an
attendance record.
dwEMachineNumber LONG*
[out]
Pointer that points
dwTMachineNumber LONG*
dwEnrollNumber
36
to the LONG
variable. Its value
is the machine ID of
an attendance
record.
dwVerifyMode
dwInOutMode
dwYear
dwMonth
dwDay
LONG*
LONG*
LONG*
LONG*
LONG*
[out]
Pointer that points
to the LONG
variable. Its value
is the verification
mode of an
attendance record.
[out]
Pointer that points
to the LONG
variable. Its value
is the attendance
status of an
attendance record.
[out]
Pointer that points
to the LONG
variable. Its value
is the year of an
attendance record.
[out]
Pointer that points
to the LONG
variable. Its value
is the month of an
attendance record.
[out]
Pointer that points
to the LONG
variable. Its value
is the day of an
attendance record.
dwHour
LONG*
[out]
Pointer that points
to the LONG
variable. Its value
is the hour of an
attendance record.
dwMinute
LONG*
[out]
Pointer that points
37
to the LONG
variable. Its value
is the minute of an
attendance record.
Returns
Value description:
name
type
description of value
True
BOOL
Function execution success
False
BOOL
Function execution failure
See also
Attention
1. The dwVerifyMode parameter specifies the verification mode. The values are described as
follows:
Generally:
0 indicates password verification, 1 indicates fingerprint verification and 2 indicates card
verification.
Under multiple verification modes:
FP_OR_PW_OR_RF 0
FP 1
PIN 2
PW 3
RF 4
FP_OR_PW 5
FP_OR_RF 6
PW_OR_RF 7
PIN_AND_FP 8
FP_AND_PW 9
FP_AND_RF 10
PW_AND_RF 11
FP_AND_PW_AND_RF 12
PIN_AND_FP_AND_PW 13
FP_AND_RF_OR_PIN 14
2. The dwInOutMode parameter specifies the attendance status. The values are described as
follows:
0-Check-In Default
1-Check-Out
2-Break-Out
3-Break-In
38
4-OT-In
5-OT-Out
Note
Applicable to BW
5.2.1.6 GetAllGLogData
VARIANT_BOOL GetAllGLogData(LONGdwMachineNumber , LONG* dwTMachineNumber,
LONG* dwEnrollNumber,LONG* dwEMachineNumber, LONG* dwVerifyMode, LONG*
dwInOutMode, LONG*dwYear, LONG* dwMonth,LONG* dwDay, LONG* dwHour,LONG*
dwMinute)
To read attendance records from the internal buffer one by one. Before using this function,
execute ReadAllGLogData or ReadGeneralLogData to read the attendance records from the
machine to the internal buffer of the PC. Each time this function is executed, the pointer moves to
the next attendance record. This function is the same as GetGeneralLogData. They differ only in
the interface name for compatibility.
Parameters
Parameter description:
name
dwMachineNumber
dwTMachineNumber
dwEnrollNumber
dwEMachineNumber
dwVerifyMode
type param direction description of param
LONG
LONG*
LONG*
LONG*
LONG*
[in]
Machine ID
[out]
Pointer that points to
the LONG variable. Its
value is the machine ID
of an attendance
record.
[out]
Pointer that points to
the LONG variable. Its
value is the user ID of
an attendance record.
[out]
Pointer that points to
the LONG variable. Its
value is the machine ID
of an attendance
record.
[out]
Pointer that points to
the LONG variable. Its
value is the
39
verification mode of
an attendance record.
dwInOutMode
LONG*
dwYear
LONG*
dwMonth
LONG*
dwDay
LONG*
dwHour
LONG*
dwMinute
LONG*
[out]
Pointer that points to
the LONG variable. Its
value is the
attendance status of
an attendance record.
[out]
Pointer that points to
the LONG variable. Its
value is the year of an
attendance record.
[out]
Pointer that points to
the LONG variable. Its
value is the month of
an attendance record.
[out]
Pointer that points to
the LONG variable. Its
value is the day of an
attendance record.
[out]
Pointer that points to
the LONG variable. Its
value is the hour of an
attendance record.
[out]
Pointer that points to
the LONG variable. Its
value is the minute of
an attendance record.
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
GetGeneralLogData
40
Attention
1. The dwVerifyMode parameter specifies the verification mode. The meanings of the values are
the same as those of the GetGeneralLogData parameter.
2. The dwInOutMode parameter specifies the attendance status. The meanings of the values are
the same as those of the GetGeneralLogData parameter.
Note
Applicable to BW
5.2.1.7 GetGeneralLogDataStr
VARIANT_BOOL GetGeneralLogDataStr(LONG dwMachineNumber, LONG*
dwEnrollNumber, LONG* dwVerifyMode, LONG* dwInOutMode, BSTR* TimeStr)
To read attendance records from the internal buffer one by one. Before using this function,
execute ReadAllGLogData or ReadGeneralLogData to read the attendance records from the
machine to the internal buffer of the PC. Each time this function is executed, the pointer moves to
the next attendance record. This function is the same as GetGeneralLogData. They differ in the
format of time in the returned values.
Parameters
Parameter description:
name
dwMachineNumber
dwEnrollNumber
dwVerifyMode
dwInOutMode
type param direction
LONG
LONG*
LONG*
LONG*
description of param
[in]
Machine ID
[out]
Pointer that points to the LONG
variable. Its value is the user ID
of an attendance record.
[out]
Pointer that points to the LONG
variable. Its value is the
verification mode of an
attendance record. The meanings
of the values are the same as those
of the GetGeneralLogData
parameter.
[out]
Pointer that points to the LONG
variable. Its value is the
attendance status of an
attendance record. The meanings
of the values are the same as those
of the GetGeneralLogData
41
parameter.
TimeStr
BSTR*
Pointer that points to the LONG
variable. Its value is the
attendance time of an attendance
record.
[out]
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
GetGeneralLogData
Attention
1. The dwVerifyMode parameter specifies the verification mode. The meanings of the values are
the same as those of the GetGeneralLogData parameter.
2. The dwInOutMode parameter specifies the attendance status. The meanings of the values are
the same as those of the GetGeneralLogData parameter.
Note
Applicable to BW
5.2.1.8 GetGeneralExtLogData
VARIANT_BOOL GetGeneralExtLogData(LONG dwMachineNumber, LONG*
dwEnrollNumber, LONG* dwVerifyMode, LONG* dwInOutMode, LONG* dwYear, LONG*
dwMonth, LONG* dwDay, LONG* dwHour, LONG* dwMinute, LONG* dwSecond, LONG*
dwWorkCode, LONG* dwReserved)
To read attendance records from the internal buffer one by one. Before using this function,
execute ReadAllGLogData or ReadGeneralLogData to read the attendance records from the
machine to the internal buffer of the PC. Each time this function is executed, the pointer moves to
the next attendance record. This function is an enhanced version of GetGeneralLogData. They are
compatible.
Parameters
Parameter description:
name
type
param direction description of param
42
dwMachineNumber
dwEnrollNumber
dwVerifyMode
dwInOutMode
dwYear
dwMonth
dwDay
dwHour
LONG
LONG*
LONG*
LONG*
LONG*
LONG*
LONG*
LONG*
[in]
Machine ID
[out]
Pointer that points to
the LONG variable. Its
value is the user ID of
an attendance record.
[out]
Pointer that points to
the LONG variable. Its
value is the
verification mode of an
attendance record.
[out]
Pointer that points to
the LONG variable. Its
value is the attendance
status of an attendance
record.
[out]
Pointer that points to
the LONG variable. Its
value is the year of an
attendance record.
[out]
Pointer that points to
the LONG variable. Its
value is the month of an
attendance record.
[out]
Pointer that points to
the LONG variable. Its
value is the day of an
attendance record.
[out]
Pointer that points to
the LONG variable. Its
value is the hour of an
attendance record.
dwMinute
LONG*
[out]
Pointer that points to
the LONG variable. Its
value is the minute of
an attendance record.
dwSecond
LONG*
[out]
Pointer that points to
43
the LONG variable. Its
value is the second of
an attendance record.
dwWorkCode
LONG*
[out]
Pointer that points to
the LONG variable. Its
value is the work code
of an attendance
record.
dwReserved
LONG*
[out]
Reserved parameter. It
is meaningless.
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
GetGeneralLogData
Attention
1. The dwVerifyMode parameter specifies the verification mode. The meanings of the values are
the same as those of the GetGeneralLogData parameter.
2. The dwInOutMode parameter specifies the attendance status. The meanings of the values are
the same as those of the GetGeneralLogData parameter.
Note
Applicable to BW
5.2.1.9 SSR_GetGeneralLogData
VARIANT_BOOL SSR_GetGeneralLogData(LONG dwMachineNumber, BSTR*
dwEnrollNumber, LONG* dwVerifyMode, LONG* dwInOutMode, LONG* dwYear, LONG*
dwMonth, LONG* dwDay, LONG* dwHour, LONG* dwMinute, LONG* dwSecond, LONG*
dwWorkcode)
To read attendance records from the internal buffer one by one. Before using this function,
execute ReadAllGLogData or ReadGeneralLogData to read the attendance records from the
machine to the internal buffer of the PC. Each time this function is executed, the pointer moves to
the next attendance record. This function is the same as GetGeneralLogData. The difference is
that this function applies to color-screen machines.
44
Parameters
Parameter description:
name
dwMachineNumber
dwEnrollNumber
dwVerifyMode
type param direction
LONG
BSTR*
LONG*
description of param
[in]
Machine ID
[out]
Pointer that points to the BSTR variable. Its
value is the user ID of an attendance record.
A user ID contains a maximum of 24 digits.
[out]
Pointer that points to the LONG variable. Its
value is the verification mode of an
attendance record.
dwInOutMode
LONG*
[out]
Pointer that points to the LONG variable. Its
value is the attendance status of an
attendance record.
dwYear
LONG*
[out]
Pointer that points to the LONG variable. Its
value is the year of an attendance record.
dwMonth
LONG*
[out]
Pointer that points to the LONG variable. Its
value is the month of an attendance record.
dwDay
LONG*
[out]
Pointer that points to the LONG variable. Its
value is the day of an attendance record.
dwHour
LONG*
[out]
Pointer that points to the LONG variable. Its
value is the hour of an attendance record.
dwMinute
LONG*
[out]
Pointer that points to the LONG variable. Its
value is the minute of an attendance record.
dwSecond
LONG*
[out]
Pointer that points to the LONG variable. Its
value is the second of an attendance record.
[out]
Pointer that points to the LONG variable. Its
value is the work code of an attendance
record.
dwWorkcode
LONG*
Returns
Value description:
45
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
1. The dwVerifyMode parameter specifies the verification mode. The values are described as
follows:
Generally:
0 indicates password verification, 1 indicates fingerprint verification and 2 indicates card
verification.
Under multiple verification modes:
FP_OR_PW_OR_RF 0
FP 1
PIN 2
PW 3
RF 4
FP_OR_PW 5
FP_OR_RF 6
PW_OR_RF 7
PIN_AND_FP 8
FP_AND_PW 9
FP_AND_RF 10
PW_AND_RF 11
FP_AND_PW_AND_RF 12
PIN_AND_FP_AND_PW 13
FP_AND_RF_OR_PIN 14
2. The dwInOutMode parameter specifies the attendance status. The values are described as
follows:
0-Check-In Default
1-Check-Out
2-Break-Out
3-Break-In
4-OT-In
5-OT-Out
Note
Applicable to TFT and IFACE devices
5.2.1.10 ClearGLog
VARIANT_BOOL ClearGLog(long dwMachineNumber)
46
To clear all attendance records on the machine.
Parameters
Parameter description:
name
type param direction description of param
dwMachineNumber LONG
[in]
Machine ID
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
5.2.1.11 DeleteAttlogBetweenTheDate
VARIANT_BOOL DeleteAttlogBetweenTheDate(LONG dwMachineNumber, BSTR sTime,
BSTR eTime)
To delete attendance records based on the specified start time and end time, accurate to seconds.
Parameters
Parameter description:
name
type param direction
dwMachineNumber LONG
description of param
[in]
Machine ID
sTime
BSTR
[in]
Start time in the format of
YYYY-MM-DD hh:mm:ss
eTime
BSTR
[in]
End time in the format of
YYYY-MM-DD hh:mm:ss
Returns
47
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
This interface is applicable to the new architecture firmware.
5.2.1.12 DeleteAttlogByTime
VARIANT_BOOL DeleteAttlogByTime(LONG dwMachineNumber, BSTR sTime)
To delete all attendance records generated before the specified time point, accurate to seconds.
Parameters
Parameter description:
name
type param direction
dwMachineNumber LONG
sTime
BSTR
description of param
[in]
Machine ID
[in]
Start time point in the
format of YYYY-MM-DD
hh:mm:ss
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
48
Note
This interface is applicable to the new architecture firmware.
5.2.2
Operation Record Data
5.2.2.1 ReadSuperLogData
VARIANT_BOOL ReadSuperLogData(long dwMachineNumber)
To read operation records to the internal buffer of the PC. The function is the same as
ReadAllSLogData.
Parameters
Parameter description:
name
type param direction
dwMachineNumber LONG
description of param
[in]
Machine ID
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
5.2.2.2 ReadAllSLogData
VARIANT_BOOL ReadAllSLogData(long dwMachineNumber)
To read operation records to the internal buffer of the PC. The function is the same as
ReadSuperLogData.
Parameters
Parameter description:
49
name
type param direction description of param
dwMachineNumber LONG
[in]
Machine ID
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
5.2.2.3 GetSuperLogData
VARIANT_BOOL GetSuperLogData(LONG dwMachineNumber, LONG* dwTMachineNumber,
LONG* dwSEnrollNumber, LONG* Params4, LONG* Params1, LONG* Params2, LONG*
dwManipulation, LONG* Params3, LONG* dwYear, LONG* dwMonth, LONG* dwDay,
LONG* dwHour, LONG* dwMinute)
To read operation records from the internal buffer one by one. Before using this function, execute
ReadAllSLogData or ReadSuperLogData to read the operation records from the machine to the
internal buffer of the PC. Each time this function is executed, the pointer moves to the next
operation record. This function differs from GetSuperLogData2 in that the GetSuperLogData2
function can obtain the operation record time accurate to seconds.
Parameters
Parameter description:
name
dwMachineNumber
type param direction
LONG
dwTMachineNumber LONG*
description of param
[in]
Machine ID
[out]
Pointer that points to the LONG
variable. Its value is the
machine ID of an operation
record.
50
dwSEnrollNumber
Params4
Params1
Params2
dwManipulation
Params3
LONG*
LONG*
LONG*
LONG*
LONG*
LONG*
[out]
Pointer that points to the LONG
variable. Its value is the
administrator ID of an operation
record.
[out]
Pointer that points to the LONG
variable. The value varies
according to that of
dwManipulation.
[out]
Pointer that points to the LONG
variable. The value varies
according to that of
dwManipulation.
[out]
Pointer that points to the LONG
variable. The value varies
according to that of
dwManipulation.
[out]
Pointer that points to the LONG
variable. Its value is the
operation type.
[out]
Pointer that points to the LONG
variable. The value varies
according to that of
dwManipulation.
dwYear
LONG*
[out]
Pointer that points to the LONG
variable. Its value is the year of
an operation record.
dwMonth
LONG*
[out]
Pointer that points to the LONG
variable. Its value is the month
of an operation record.
[out]
Pointer that points to the LONG
variable. Its value is the day of
an operation record.
[out]
Pointer that points to the LONG
variable. Its value is the hour of
an operation record.
dwDay
dwHour
LONG*
LONG*
51
dwMinute
LONG*
Pointer that points to the LONG
variable. Its value is the minute
of an operation record.
[out]
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
The meaning of different combinations of the dwManipulation, Params1, Params2, Params3 and
Params4 parameters is as follows:
1. dwManipulation=0: dwManipulation indicates starting the machine.
2. dwManipulation=1: dwManipulation indicates shutting down the machine.
3. dwManipulation=3: dwManipulation indicates that an alarm is raised. Params1 specifies the
alarm type. The value 58 indicates a misoperation alarm, 54 door sensor alarm, 53 door opening
alarm, 55 tamper alarm, and 65535 shutdown alarm.
4. dwManipulation=4: dwManipulation indicates accessing the menu.
5. dwManipulation=5: dwManipulation indicates changing settings. Params1 specifies the
number of the option that is set.
6. dwManipulation=6: dwManipulation indicates registering fingerprints. Params1 specifies the
ID of the operated user. Params2 specifies the operation result, the value 0 indicates operation
success, and other values indicate operation failure. Params3 specifies the registered fingerprint
index. Params4 specifies the length of the fingerprint template, and the value 2 indicates duress
fingerprint.
7. dwManipulation=7: dwManipulation indicates registering the password. Params1 specifies the
ID of the operated user. Params2 specifies the operation result, the value 0 indicates operation
success, and other values indicate operation failure.
8. dwManipulation=14: dwManipulation indicates creating an MF card. Params1 specifies the ID
of the operated user. Params2 specifies the operation result, the value 0 indicates operation
success, and other values indicate operation failure. Params3 specifies the number of fingerprints
written to the MF card. Params4 specifies the size of fingerprint data written to the MF card.
9. dwManipulation=20: dwManipulation indicates copying data from the MF card to the machine.
Params1 specifies the ID of the operated user. Params2 specifies the operation result, the value 0
indicates operation success, and other values indicate operation failure. Params3 specifies the
number of fingerprints read to the MF card.
52
10. dwManipulation=22: dwManipulation indicates restoring factory settings.
11. dwManipulation=30: dwManipulation indicates registering a new user. Params1 specifies the
ID of the operated user. Params2 specifies the operation result, the value 0 indicates operation
success, and other values indicate operation failure.
12. dwManipulation=32: dwManipulation indicates duress alarm. Params1 specifies whether the
alarm is a verification alarm, the value 0 indicates a key alarm, and 1 indicates a verification
alarm. Note: If the alarm is a verification alarm, dwSEnrollNumber will return the duress user
ID.
13. dwManipulation=34: dwManipulation indicates blockade. Params1 specifies whether to
block.
Note
Applicable to BW, TFT and IFACE devices
5.2.2.4 GetAllSLogData
GetAllSLogData(LONG dwMachineNumber, LONG* dwTMachineNumber, LONG*
dwSEnrollNumber, LONG* dwSMachineNumber, LONG* dwGEnrollNumber, LONG*
dwGMachineNumber, LONG* dwManipulation, LONG* dwBackupNumber, LONG* dwYear,
LONG* dwMonth, LONG* dwDay, LONG* dwHour, LONG* dwMinute)
To read operation records from the internal buffer one by one. Before using this function, execute
ReadAllSLogData or ReadSuperLogData to read the operation records from the machine to the
internal buffer of the PC. Each time this function is executed, the pointer moves to the next
operation record. This function is the same as GetSuperLogData. They differ only in the interface
name for compatibility.
Parameters
Parameter description:
name
dwMachineNumber
type param direction
LONG
description of param
[in]
Machine ID
[out]
Pointer that points to the LONG
variable. Its value is the
machine ID of an operation
record.
LONG*
[out]
Pointer that points to the LONG
variable. Its value is the
administrator ID of an operation
record.
dwSMachineNumber LONG*
[out]
Pointer that points to the LONG
variable. The value varies
dwTMachineNumber LONG*
dwSEnrollNumber
53
according to that of
dwManipulation.
dwGEnrollNumber
LONG*
dwGMachineNumber LONG*
dwManipulation
dwBackupNumber
dwYear
dwMonth
LONG*
LONG*
LONG*
LONG*
[out]
Pointer that points to the LONG
variable. The value varies
according to that of
dwManipulation.
[out]
Pointer that points to the LONG
variable. The value varies
according to that of
dwManipulation.
[out]
Pointer that points to the LONG
variable. Its value is the
operation type. The meanings of
the values are as follows:
[out]
Pointer that points to the LONG
variable. The value varies
according to that of
dwManipulation.
[out]
Pointer that points to the LONG
variable. Its value is the year
of an operation record.
[out]
Pointer that points to the LONG
variable. Its value is the month
of an operation record.
dwDay
LONG*
[out]
Pointer that points to the LONG
variable. Its value is the day of
an operation record.
dwHour
LONG*
[out]
Pointer that points to the LONG
variable. Its value is the hour
of an operation record.
[out]
Pointer that points to the LONG
variable. Its value is the minute
of an operation record.*
dwMinute
LONG*
Returns
Value description:
54
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
GetSuperLogData
Attention
The meanings of the parameters are the same as those of GetSuperLogData.
Note
Applicable to BW, TFT and IFACE devices
5.2.2.5 ClearSLog
VARIANT_BOOL ClearSLog(LONG dwMachineNumber)
To clear all operation records on the machine.
Parameters.
Parameter description:
name
type param direction description of param
dwMachineNumber LONG
[in]
Machine ID
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
55
5.2.2.6 GetSuperLogData2
VARIANT_BOOL GetSuperLogData2(LONG dwMachineNumber, LONG*
dwTMachineNumber, LONG* dwSEnrollNumber, LONG* Params4, LONG* Params1, LONG*
Params2, LONG* dwManipulation, LONG* Params3, LONG* dwYear, LONG* dwMonth,
LONG* dwDay, LONG* dwHour,LONG* dwMinute, LONG* dwSecs)
To read operation records from the internal buffer one by one. Before using this function, execute
ReadAllSLogData or ReadSuperLogData to read the operation records from the machine to the
internal buffer of the PC. Each time this function is executed, the pointer moves to the next
operation record. GetSuperLogData and GetSuperLogData2 differ in that the GetSuperLogData2
function can obtain the operation record time accurate to seconds.
Parameters
Parameter description:
name
dwMachineNumber
type param direction
LONG
dwTMachineNumber LONG*
dwSEnrollNumber
Params4
Params1
LONG*
LONG*
LONG*
description of param
[in]
Machine ID
[out]
Pointer that points to the LONG
variable. Its value is the
machine ID of an operation
record.
[out]
Pointer that points to the LONG
variable. Its value is the
administrator ID of an operation
record.
[out]
Pointer that points to the LONG
variable. The value varies
according to that of
dwManipulation.
[out]
Pointer that points to the LONG
variable. The value varies
according to that of
dwManipulation.
Params2
LONG*
[out]
Pointer that points to the LONG
variable. The value varies
according to that of
dwManipulation.
dwManipulation
LONG*
[out]
Pointer that points to the LONG
56
variable. Its value is the
operation type. The meanings of
the values are as follows:
Params3
dwYear
dwMonth
dwDay
dwHour
dwMinute
dwSecs
LONG*
LONG*
LONG*
LONG*
LONG*
LONG*
LONG*
[out]
Pointer that points to the LONG
variable. The value varies
according to that of
dwManipulation.
[out]
Pointer that points to the LONG
variable. Its value is the year
of an operation record.
[out]
Pointer that points to the LONG
variable. Its value is the month
of an operation record.
[out]
Pointer that points to the LONG
variable. Its value is the day of
an operation record.
[out]
Pointer that points to the LONG
variable. Its value is the hour
of an operation record.
[out]
Pointer that points to the LONG
variable. Its value is the minute
of an operation record.
[out]
Pointer that points to the LONG
variable. Its value is the second
of an operation record.
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
GetSuperLogData
Attention
57
dwYear, dwMonth, dwDay, dwHour, dwMinute and dwSecs are all pointers that point to the
LONG variable. Their values indicate the date and time of an operation record, accurate to
seconds.
Note
Applicable to BW, TFT and IFACE devices
5.2.3
User Information Functions
5.2.3.1 ReadAllUserID
VARIANT_BOOL ReadAllUserID(LONG dwMachineNumber)
To read all user information to the memory of the PC, including the user ID, password, name, and
card number. Fingerprint templates are not read. After this function is executed, invoke the
function GetAllUserID to get the user information.
Parameters
Parameter description:
name
type param direction
dwMachineNumber LONG
description of param
[in]
Machine ID
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
5.2.3.2 EnableUser
VARIANT_BOOL EnableUser(LONG dwMachineNumber, LONG dwEnrollNumber,
LONG dwEMachineNumber, LONG dwBackupNumber, VARIANT_BOOL bFlag)
To set whether a user account is available.
Parameters
Parameter description:
58
name
type param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
dwEnrollNumber
LONG
[in]
User ID
dwEMachineNumber LONG
[in]
Invalid parameter. It is
meaningless.
dwBackupNumber
LONG
[in]
Invalid parameter. It is
meaningless.
bFlag
BOOL
[in]
Flag that indicates whether
a user account is enabled
Returns
Value description:
name type
True
description of value
BOOL Function execution success
False BOOL Function execution failure
See also
Attention
The bFlag parameter is a flag that indicates whether a user account is enabled. The value True
indicates that the user account is enabled and False indicates that the user account is disabled.
Note
Applicable to BW
5.2.3.3 SSR_EnableUser
VARIANT_BOOL SSR_EnableUser(LONG dwMachineNumber, BSTR dwEnrollNumber,
VARIANT_BOOL bFlag)
To set whether a user account is available.
Parameters
Parameter description:
name
type param direction
description of param
59
dwMachineNumber LONG
[in]
Machine ID
dwEnrollNumber
BSTR
[in]
User ID
bFlag
BOOL
[in]
Flag that indicates whether a user
account is enabled
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
The bFlag parameter is a flag that indicates whether a user account is enabled. The value True
indicates that the user account is enabled and False indicates that the user account is disabled.
Note
Applicable to TFT and IFACE devices
5.2.3.4 SetUserInfoEx
VARIANT_BOOL SetUserInfoEx(LONG dwMachineNumber, LONG dwEnrollNumber, LONG
VerifyStyle, BYTE* Reserved)
To upload the user verification mode or group verification mode.
Parameters
Parameter description:
name
type param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
dwEnrollNumber
LONG
[in]
User ID
VerifyStyle
LONG
[in]
Verification mode
Reserved
BYTE*
[in]
Reserved
60
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
1. This function is valid only on machines with multiple verification modes.
2. On a monochrome machine, the VerifyStyle parameter specifies the verification mode, and 15
verification modes are available. For details about the meanings of the values, see the description
of the GetGeneralLogData parameter. If a group verification mode is used, the value of
VerifyStyle ranges from 129 to 124, indicating group 1 to group 5 respectively.
3. On a color-screen machine, the VerifyStyle parameter specifies the verification mode. On the
color-screen access control fingerprint machine, the value 0 indicates group verification.
128(FP/PW/RF), 129(FP), 130(PIN), 131(PW), 132(RF), 133(FP&RF), 134(FP/PW),
135(FP/RF), 136(PW/RF), 137(PIN&FP), 138(FP&PW), 139(PW&RF), 140(FP&PW&RF),
141(PIN&FP&PW), 142(FP&RF/PIN).
Note
Applicable to BW, TFT and IFACE devices
5.2.3.5 GetAllUserID
VARIANT_BOOL GetAllUserID(LONG dwMachineNumber, LONG* dwEnrollNumber,
LONG* dwEMachineNumber, LONG* dwBackupNumber, LONG* dwMachinePrivilege,
LONG* dwEnable)
To get all user information. Before executing this function, invoke the function ReadAllUserID to
read all user information to the memory. Each time GetAllUserID is executed, the pointer moves
to the next user information record. After all user information is read, the function returns False.
This function differs from GetAllUserInfo in that the GetAllUserInfo function can obtain user
names and passwords.
Parameters
Parameter description:
name
type
param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
61
dwEnrollNumber
LONG*
[out]
User ID
dwEMachineNumber
LONG*
[out]
Invalid parameter
dwBackupNumber
LONG*
[out]
Comment
dwMachinePrivilege
LONG*
[out]
User privilege
dwEnable
LONG*
[out]
Whether a user account is enabled
Returns
Value description:
name
type
description of value
True
BOOL
Function execution success
False
BOOL
Function execution failure
See also
Attention
1. The value of dwEMachineNumber is always 0.
2. The dwMachinePrivilege parameter specifies the user privilege. The value 0 indicates common
user, 1 registrar, 2 administrator, and 3 super administrator.
3. The dwEnable parameter specifies whether a user account is enabled. The value 1 indicates
that the user account is enabled and 0 indicates that the user account is disabled.
Note
Applicable to BW
5.2.3.6 GetAllUserInfo
VARIANT_BOOL GetAllUserInfo(LONG dwMachineNumber, LONG* dwEnrollNumber,
BSTR* Name, BSTR* Password, LONG* Privilege, VARIANT_BOOL* Enabled)
To get all user information. Before executing this function, invoke the function ReadAllUserID to
read all user information to the memory. Each time GetAllUserInfo is executed, the pointer
moves to the next user information record. After all user information is read, the function returns
False. The GetAllUserInfo function differs from GetAllUserID in that it can obtain more
information.
Parameters
Parameter description:
62
name
type
param direction
description of param
dwMachineNumber
LONG
[out]
Machine ID
dwEnrollNumber
LONG*
[out]
User ID
Name
BSTR*
[out]
User name
Name
BSTR*
[out]
User password
Privilege
LONG*
[out]
User privilege
Enabled
BOOL*
[out]
Whether a user account is enabled
Returns
Value description:
name
type
description of value
True
BOOL
Function execution success
False
BOOL
Function execution failure
See also
Attention
1. The dwMachinePrivilege parameter specifies the user privilege. The value 0 indicates common
user, 1 registrar, 2 administrator, and 3 super administrator.
2. The dwEnable parameter specifies whether a user account is enabled. The value 1 indicates
that the user account is enabled and 0 indicates that the user account is disabled.
Note
Applicable to BW
5.2.3.7 GetUserInfoEx
VARIANT_BOOL GetUserInfoEx(LONG dwMachineNumber, LONG dwEnrollNumber,
LONG* VerifyStyle, BYTE* Reserved)
To obtain the user verification mode.
Parameters
Parameter description:
name
type param direction
63
description of param
dwMachineNumber
LONG
[in]
Machine ID
dwEnrollNumber
LONG
[in]
User ID
VerifyStyle
LONG*
[out]
The value is the user verification
mode described by dwEnrollNumber.
Reserved
BYTE*
[out]
Reserved
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
1. This function is valid only on machines with multiple verification modes.
2. On a monochrome machine, the VerifyStyle parameter specifies the verification mode, and 15
verification modes are available. For details about the meanings of the values, see the description
of the GetGeneralLogData parameter. If a group verification mode is used, the value of
VerifyStyle ranges from 129 to 124, indicating group 1 to group 5 respectively.
3. On a color-screen machine, the VerifyStyle parameter specifies the verification mode. On the
color-screen access control fingerprint machine, the value 0 indicates group verification.
128(FP/PW/RF), 129(FP), 130(PIN), 131(PW), 132(RF), 133(FP&RF), 134(FP/PW),
135(FP/RF), 136(PW/RF), 137(PIN&FP), 138(FP&PW), 139(PW&RF), 140(FP&PW&RF),
141(PIN&FP&PW), 142(FP&RF/PIN).
Note
Applicable to BW, TFT and IFACE devices
5.2.3.8 DeleteUserInfoEx
VARIANT_BOOL DeleteUserInfoEx(LONG dwMachineNumber, LONG dwEnrollNumber)
To delete the multiple verification modes set by a specified user.
Parameters
Parameter description:
name
type param direction description of param
64
dwMachineNumber LONG
[in]
Machine ID
dwEnrollNumber
[in]
User ID
LONG
Returns
Value description:
name type
True
description of value
BOOL Function execution success
False BOOL Function execution failure
See also
Attention
This function is valid only on machines with multiple verification modes.
Note
Applicable to BW, TFT and IFACE devices
5.2.3.9 SSR_GetAllUserInfo
VARIANT_BOOL SSR_GetAllUserInfo(LONG dwMachineNumber, BSTR* dwEnrollNumber,
BSTR* Name, BSTR* Password, LONG* Privilege, VARIANT_BOOL* Enabled)
To get all user information. Before executing this function, invoke the function ReadAllUserID to
read all user information to the memory. Each time SSR_GetAllUserInfo is executed, the pointer
moves to the next user information record. After all user information is read, the function returns
False.
Parameters
Parameter description:
name
type param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
dwEnrollNumber
BSTR*
[out]
User ID
Name
BSTR*
[out]
User name
Name
BSTR*
[out]
User password
Privilege
LONG*
[out]
User privilege
65
Enabled
BOOL*
Flag that indicates whether a
user account is enabled
[out]
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
1. The Privilege parameter specifies the user privilege. The value 0 indicates common user, 1
registrar, 2 administrator, and 3 super administrator.
2. The Enable parameter specifies whether a user account is enabled. The value 1 indicates that
the user account is enabled and 0 indicates that the user account is disabled.
Note
Applicable to TFT and IFACE devices
5.2.3.10 GetUserInfo
VARIANT_BOOL GetUserInfo(LONG dwMachineNumber, LONG dwEnrollNumber,
BSTR* Name, BSTR* Password, LONG* Privilege, VARIANT_BOOL * Enabled)
To get information about a specified user.
Parameters
Parameter description:
name
type param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
dwEnrollNumber
LONG
[in]
User ID
Name
BSTR*
[out]
Returned user name
Password
BSTR*
[out]
User password
66
Privilege
Enabled
LONG*
BOOL*
[out]
User privilege
[out]
Flag that indicates
whether a user account is
enabled
Returns
Value description:
name
type
description of value
True
BOOL
Function execution success
False
BOOL
Function execution failure
See also
Attention
1. The Password indicates the returned user password. If this parameter is left blank, the user
does not use a password on the machine.
2. The Privilege parameter specifies the user privilege. The value 0 indicates common user, 1
registrar, 2 administrator, and 3 super administrator.
3. The Enable parameter specifies whether a user account is enabled. The value 1 indicates that
the user account is enabled and 0 indicates that the user account is disabled.
Note
Applicable to BW
5.2.3.11 GetUserInfoByPIN2
VARIANT_BOOL GetUserInfoByPIN2(LONG dwMachineNumber, BSTR* Name,
BSTR* Password, LONG* Privilege, VARIANT_BOOL* Enabled)
To obtain user information based on the current attribute value pin2.
Parameters
Parameter description:
name
type param direction description of param
dwMachineNumber
LONG
[in]
Machine ID
Name
BSTR*
[out]
User name
Password
BSTR*
[out]
User password
67
Privilege
LONG*
Enabled
BOOL*
[out]
User privilege
[out]
Flag that indicates
whether a user account
is enabled
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
1. The Privilege parameter specifies the user privilege. The value 0 indicates common user, 1
registrar, 2 administrator, and 3 super administrator.
2. The Enable parameter specifies whether a user account is enabled. The value 1 indicates that
the user account is enabled and 0 indicates that the user account is disabled.
Note
Applicable to BW
5.2.3.12 GetUserInfoByCard
VARIANT_BOOL GetUserInfoByCard(LONG dwMachineNumber, BSTR* Name,
BSTR* Password, LONG* Privilege, VARIANT_BOOL* Enabled)
To obtain user information based on the current attribute value CardNumber.
Parameters
Parameter description:
name
type param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
Name
BSTR*
[out]
User name
Password
BSTR*
[out]
User password
Privilege
LONG*
[out]
User privilege
68
Enabled
BOOL*
Flag that indicates
whether a user account is
enabled
[out]
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
1. The Privilege parameter specifies the user privilege. The value 0 indicates common user, 1
registrar, 2 administrator, and 3 super administrator.
2. The Enable parameter specifies whether a user account is enabled. The value 1 indicates that
the user account is enabled and 0 indicates that the user account is disabled.
Note
Applicable to BW
5.2.3.13 GetUserIDByPIN2
VARIANT_BOOL GetUserIDByPIN2(LONG PIN2, LONG* UserID)
To obtain the user ID based on pin2.
Parameters
Parameter description:
name
type param direction
description of param
PIN2
LONG
[in]
Pin2 value
UserID LONG*
[out]
User ID
Returns
Value description:
name type
description of value
69
True
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to BW
5.2.3.14 GetPIN2
VARIANT_BOOL GetPIN2(LONG UserID, LONG* PIN2)
To obtain the pin2 value based on the user ID.
Parameters
Parameter description:
name
type param direction
description of param
UserID
LONG
[in]
User ID
PIN2
LONG*
[out]
Pin2 value
Returns
Value description:
name
type
description of value
True
BOOL
Function execution success
False
BOOL
Function execution failure
See also
Attention
Note
Applicable to BW
5.2.3.15 SSR_GetUserInfo
VARIANT_BOOL SSR_GetUserInfo(LONG dwMachineNumber, BSTR dwEnrollNumber,
BSTR* Name, BSTR* Password, LONG* Privilege, VARIANT_BOOL* Enabled)
To obtain information about a specified user.
Parameters
70
Parameter description:
name
type param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
dwEnrollNumber
BSTR
[in]
User ID
[out]
The value is the user name
described by
dwEnrollNumber.
Name
BSTR*
Password
BSTR*
[out]
The value is the user
password described by
dwEnrollNumber.
Privilege
LONG*
[out]
The value is the user
privilege described by
dwEnrollNumber.
[out]
Flag that indicates
whether a user account is
enabled
Enabled
BOOL*
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
1. The Privilege parameter specifies the user privilege. The value 0 indicates common user, 1
registrar, 2 administrator, and 3 super administrator.
2. The Enable parameter specifies whether a user account is enabled. The value 1 indicates that
the user account is enabled and 0 indicates that the user account is disabled.
Note
Applicable to TFT and IFACE devices
71
5.2.3.16 SetUserInfo
VARIANT_BOOL SetUserInfo(LONG dwMachineNumber, LONG dwEnrollNumber,
BSTR Name, BSTR Password, LONG Privilege, VARIANT_BOOL Enabled)
To set information about a user. If the user does not exist on the machine, the user will be created.
Parameters
Parameter description:
name
type param direction description of param
dwMachineNumber LONG
[in]
Machine ID
dwEnrollNumber
LONG
[in]
User ID
Name
BSTR
[in]
User name to be set
[in]
User password to be
set. If this parameter
is left blank, the
password of the user
will be cleared on the
machine.
[in]
User privilege. The
value 0 indicates
common user, 1
registrar, 2
administrator, and 3
super administrator.
[in]
Flag that indicates
whether a user account
is enabled. The value 1
indicates that the
user account is
enabled and 0
indicates that the
user account is
disabled.
Password
Privilege
Enabled
BSTR
LONG
BOOL
Returns
Value description:
72
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
1. The Password parameter specifies the password to be set. If this parameter is left blank, the
password of the user will be cleared on the machine.
2. The Privilege parameter specifies the user privilege. The value 0 indicates common user, 1
registrar, 2 administrator, and 3 super administrator.
3. The Enable parameter specifies whether a user account is enabled. The value 1 indicates that
the user account is enabled and 0 indicates that the user account is disabled.
Note
Applicable to BW
5.2.3.17 SSR_SetUserInfo
VARIANT_BOOL SetUserInfo(LONG dwMachineNumber, LONG dwEnrollNumber, BSTR
Name, BSTR Password, LONG Privilege, VARIANT_BOOL Enabled)
To set information about a user. If the user does not exist on the machine, the user will be created.
Parameters
Parameter description:
name
type param direction
description of param
dwMachineNumber LONG
[in]
Machine ID
dwEnrollNumber
BSTR
[in]
User ID
Name
BSTR
[in]
User name
Password
BSTR
[in]
User password
Privilege
LONG
[in]
User privilege
[in]
Flag that indicates
whether a user account is
enabled
Enabled
BOOL
Returns
73
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
1. The Privilege parameter specifies the user privilege. The value 0 indicates common user, 1
registrar, 2 administrator, and 3 super administrator.
2. The Enable parameter specifies whether a user account is enabled. The value 1 indicates that
the user account is enabled and 0 indicates that the user account is disabled.
Note
Applicable to TFT and IFACE devices
5.2.3.18 ModifyPrivilege
VARIANT_BOOL ModifyPrivilege(LONG dwMachineNumber, LONG dwEnrollNumber, LONG
dwEMachineNumber, LONG dwBackupNumber, LONG dwMachinePrivilege)
To modify user privilege.
Parameters
Parameter description:
description of
name
type param direction
param
dwMachineNumber
LONG
[in]
Machine ID
dwEnrollNumber
LONG
[in]
User ID
dwEMachineNumber
LONG
[in]
Invalid parameter.
It is meaningless.
dwBackupNumber
LONG
[in]
Invalid parameter.
It is meaningless.
dwMachinePrivilege LONG
[in]
User privilege to be
set
Returns
74
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
The dwMachinePrivilege parameter specifies the user privilege. The value 0 indicates common
user, 1 registrar, 2 administrator, and 3 super administrator.
Note
Applicable to BW
5.2.4
Registration Data Functions (Including Both User Information and
Fingerprint)
5.2.4.1 GetEnrollData
VARIANT_BOOL GetEnrollData(LONG dwMachineNumber, LONG dwEnrollNumber,
LONG dwEMachineNumber, LONG dwBackupNumber, LONG* dwMachinePrivilege,
LONG* dwEnrollData, LONG* dwPassWord)
To obtain registration data (fingerprint template and part of the user information) based on the
user ID and corresponding index.
Parameters
Parameter description:
name
type param direction description of param
dwMachineNumber
LONG
[in]
Machine ID
dwEnrollNumber
LONG
[in]
Machine ID
dwEMachineNumber
LONG
[in]
User ID
dwBackupNumber
LONG
[in]
Fingerprint index
dwMachinePrivilege LONG*
[out]
User privilege
dwEnrollData
LONG*
[out]
Fingerprint template
dwPassWord
LONG*
[out]
Password
75
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
1. The values of dwMachineNumber and dwEMachineNumber must be the same.
2. The fingerprint index ranges from 0 to 9. If the fingerprint template is obtained successfully,
the password also is obtained. The index 10 indicates obtaining only the password.
3. The value 0 indicates common user, 1 registrar, 2 administrator, and 3 super administrator.
Note
Applicable to BW
5.2.4.2 SetEnrollData
VARIANT_BOOL SetEnrollData(LONG dwMachineNumber, LONG dwEnrollNumber,
LONG dwEMachineNumber, LONG dwBackupNumber, LONG dwMachinePrivilege,
LONG* dwEnrollData, LONG dwPassWord)
To set registration data (fingerprint template and part of the user information)
Parameters
Parameter description:
name
type param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
dwEnrollNumber
LONG
[in]
Machine ID
dwEMachineNumber
LONG
[in]
User ID
dwBackupNumber
LONG
[in]
Fingerprint index
dwMachinePrivilege
LONG
[in]
User privilege
dwEnrollData
LONG*
[in]
Fingerprint template to
be uploaded
76
dwPassWord
LONG
[in]
User password
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
1. The values of dwMachineNumber and dwEMachineNumber must be the same.
2. The fingerprint index ranges from 0 to 9. The index 10 indicates setting the user password.
3. The value 0 indicates common user, 1 registrar, 2 administrator, and 3 super administrator.
Note
Applicable to BW
5.2.4.3 DeleteEnrollData
VARIANT_BOOL DeleteEnrollData(LONG dwMachineNumber, LONG dwEnrollNumber,
LONG dwEMachineNumber, LONG dwBackupNumber)
To delete registration data.
Parameters
Parameter description:
name
type param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
dwEnrollNumber
LONG
[in]
User ID
dwEMachineNumber LONG
[in]
Machine ID
[in]
Fingerprint index
dwBackupNumber
LONG
Returns
Value description:
77
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
1. The values of dwMachineNumber and dwEMachineNumber must be the same.
2. The dwBackupNumber parameter specifies the fingerprint index. The meanings are described
as follows:
The index range is 0-9. The machine will also check whether a user has other fingerprints and
passwords. If no, the machine will delete the user. The index 10 indicates deleting the password.
The machine will also check whether the user has fingerprint data. If no, the machine will delete
the user. The index 11 indicates deleting all fingerprint data of the user, and 12 indicates deleting
the user (including the fingerprints, card number and password).
Note
Applicable to BW
5.2.4.4 SSR_DeleteEnrollData
VARIANT_BOOL SSR_DeleteEnrollData(LONG dwMachineNumber, BSTR dwEnrollNumber,
LONG dwBackupNumber)
To delete registration data.
Parameters
Parameter description:
name
type param direction
description of param
dwMachineNumber LONG
[in]
Machine ID
dwEnrollNumber
BSTR
[in]
User ID
dwBackupNumber
LONG
[in]
Fingerprint index
Returns
Value description:
name type
description of value
78
True
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
The dwBackupNumber parameter specifies the fingerprint index. The meanings
are described as follows:
The index range is 0-9. The machine will also check whether a user has other
fingerprints and passwords. If no, the machine will delete the user. The index
10 indicates deleting the password. The machine will also check whether the
user has fingerprint data. If no, the machine will delete the user. The index
11 indicates deleting all fingerprint data of the user, and 12 indicates
deleting the user (including the fingerprints, card number and password).
Note
Applicable to TFT and IFACE devices
5.2.4.5 SSR_DeleteEnrollDataExt
VARIANT_BOOL SSR_DeleteEnrollDataExt(LONG dwMachineNumber,
BSTR dwEnrollNumber, LONG dwBackupNumber)
To delete registration data.
Parameters
Parameter description:
name
type param direction
description of param
dwMachineNumber LONG
[in]
Machine ID
dwEnrollNumber
BSTR
[in]
User ID
dwBackupNumber
LONG
[in]
Fingerprint index
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
79
See also
Attention
1. The dwBackupNumber parameter specifies the fingerprint index. The meanings are described
as follows:
The index range is 0-9. The machine will also check whether a user has other fingerprints and
passwords. If no, the machine will delete the user. The index 10 indicates deleting the password.
The machine will also check whether the user has fingerprint data. If no, the machine will delete
the user. The indexes 11 and 13 indicate deleting all fingerprint data of the user. The index 12
indicates deleting the user, including the fingerprints, card number and password.
2. This function differs from SSR_DeleteEnrollData in that it can delete all fingerprint data by
using parameter 13, and therefore this function has higher efficiency.
Note
Applicable to TFT and IFACE devices
5.2.4.6 GetEnrollDataStr
VARIANT_BOOL GetEnrollDataStr(LONG dwMachineNumber, LONG dwEnrollNumber,
LONG dwEMachineNumber, LONG dwBackupNumber, LONG* dwMachinePrivilege, BSTR*
dwEnrollData, LONG* dwPassWord)
To obtain registration data (fingerprint template and part of the user information) based on the
user ID and corresponding index. This function differs from GetEnrollData only in the fingerprint
template format.
Parameters
Parameter description:
name
type param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
dwEnrollNumber
LONG
[in]
Machine ID
dwEMachineNumber
LONG
[in]
User ID
dwBackupNumber
LONG
[in]
Fingerprint index
dwMachinePrivilege LONG*
[out]
User privilege
dwEnrollData
BSTR*
[out]
Fingerprint template to be
uploaded
dwPassWord
LONG*
[out]
User password
Returns
80
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
1. The values of dwMachineNumber and dwEMachineNumber must be the same.
2. The fingerprint index ranges from 0 to 9. If the fingerprint template is obtained successfully,
the password also is obtained. The index 10 indicates obtaining only the password.
3. The value 0 indicates common user, 1 registrar, 2 administrator, and 3 super administrator.
Note
Applicable to BW
5.2.4.7 SetEnrollDataStr
VARIANT_BOOL SetEnrollDataStr(LONG dwMachineNumber, LONG dwEnrollNumber,
LONG dwEMachineNumber, LONG dwBackupNumber, LONG dwMachinePrivilege,
BSTR dwEnrollData, LONG dwPassWord)
To set registration data (fingerprint template and part of the user information)
Parameters
Parameter description:
name
type param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID. The two
values must be the same.
dwEnrollNumber
LONG
[in]
Machine ID. The two
values must be the same.
dwEMachineNumber
LONG
[in]
User ID
dwBackupNumber
LONG
[in]
Fingerprint index
dwMachinePrivilege
LONG
[in]
User privilege
dwEnrollData
BSTR
[in]
Fingerprint template to
be uploaded
81
dwPassWord
LONG
[in]
User password
Returns
Value description:
name
type description of value
True
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
1. The values of dwMachineNumber and dwEMachineNumber must be the same.
2. The fingerprint index ranges from 0 to 9. If the fingerprint template is obtained successfully,
the password also is obtained. The index 10 indicates obtaining only the password.
3. The value 0 indicates common user, 1 registrar, 2 administrator, and 3 super administrator.
4. The dwEnrollData parameter specifies the uploaded fingerprint template, which is a character
string.
Note
Applicable to BW
5.2.5
Fingerprint Template Functions
5.2.5.1 ReadAllTemplate
VARIANT_BOOL ReadAllTemplate(LONG dwMachineNumber)
To read all fingerprint templates on the machine to the memory of the PC. This function reads all
fingerprint data to the memory at a time. Compared with the function that reads data records from
the machine one by one, this function has higher efficiency.
Parameters
Parameter description:
name
type param direction
dwMachineNumber LONG
description of param
[in]
Machine ID
Returns
Value description:
82
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
5.2.5.2 SSR_GetUserTmp
VARIANT_BOOL GetUserTmp(LONG dwMachineNumber, BSTR dwEnrollNumber,
LONG dwFingerIndex, BYTE* TmpData, LONG* TmpLength)
To obtain a fingerprint template in binary format. This function differs from
SSR_GetUserTmpStr only in the fingerprint template format.
Parameters
Parameter description:
name
type
param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
dwEnrollNumber
BSTR
[in]
User ID
dwFingerIndex
LONG
[in]
Fingerprint index, ranging from 0 to 9
TmpData
BYTE*
[in]
Fingerprint template data
TmpLength
LONG*
[in]
Length of the fingerprint template
Returns
Value description:
name
type
description of value
True
BOOL
Function execution success
False
BOOL
Function execution failure
83
See also
Attention
Note
Applicable to TFT
5.2.5.3 SSR_GetUserTmpStr
VARIANT_BOOL GetUserTmpStr(LONG dwMachineNumber, BSTR dwEnrollNumber,
LONG dwFingerIndex, BSTR* TmpData, LONG* TmpLength)
To obtain a fingerprint template in character string format. This function differs from
SSR_GetUserTmp only in the fingerprint template format.
Parameters
Parameter description:
name
type
param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
dwEnrollNumber
BSTR
[in]
User ID
dwFingerIndex
LONG
[in]
Fingerprint index, ranging from 0 to 9
TmpData
BSTR*
[out]
Fingerprint template data
TmpLength
LONG*
[out]
Length of the fingerprint template
Returns
Value description:
name
type
description of value
True
BOOL
Function execution success
False
BOOL
Function execution failure
See also
Attention
Note
Applicable to TFT
5.2.5.4 SSR_SetUserTmp
VARIANT_BOOL SetUserTmp(LONG dwMachineNumber, BSTR dwEnrollNumber, LONG
84
dwFingerIndex, BYTE* TmpData)
To upload a fingerprint template in binary format. This function differs from
SSR_SetUserTmpStr only in the fingerprint template format.
Parameters
Parameter description:
name
type
param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
dwEnrollNumber
BSTR
[in]
User ID
dwFingerIndex
LONG
[in]
Fingerprint index, ranging from 0
to 9
TmpData
BYTE*
[in]
Fingerprint template
Returns
Value description:
name
type
description of value
True
BOOL
Function execution success
False
BOOL
Function execution failure
See also
Attention
Note
Applicable to TFT
5.2.5.5 SSR_SetUserTmpStr
VARIANT_BOOL SetUserTmpStr(LONG dwMachineNumber, BSTR dwEnrollNumber, LONG
dwFingerIndex, BSTR TmpData)
To upload a fingerprint template in character string format. This function differs from
SSR_SetUserTmp only in the fingerprint template format.
Parameters
Parameter description:
name
type
param direction
85
description of param
dwMachineNumber
LONG
[in]
Machine ID
dwEnrollNumber
BSTR
[in]
User ID
LONG dwFingerIndex
LONG
[in]
Fingerprint index, ranging from
0 to 9
TmpData
BSTR
[in]
Fingerprint template
Returns
Value description:
name
type
description of value
True
BOOL
Function execution success
False
BOOL
Function execution failure
See also
Attention
Note
Applicable to TFT
5.2.5.6 DelUserTmp
VARIANT_BOOL DelUserTmp(LONG dwMachineNumber, LONG dwEnrollNumber,
LONG dwFingerIndex)
To delete a specified fingerprint template.
Parameters
Parameter description:
name
type param direction
description of param
dwMachineNumber LONG
[in]
Machine ID
dwEnrollNumber
LONG
[in]
User ID
dwFingerIndex
LONG
[in]
Fingerprint index
Returns
Value description:
86
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to BW
5.2.5.7 SSR_DelUserTmp
VARIANT_BOOL SSR_DelUserTmp(LONG dwMachineNumber, BSTR dwEnrollNumber,
LONG dwFingerIndex)
To delete a fingerprint template.
Parameters
Parameter description:
name
type param direction
description of param
dwMachineNumber LONG
[in]
Machine ID
dwEnrollNumber
BSTR
[in]
User ID
dwFingerIndex
LONG
[in]
Fingerprint index, ranging from
0 to 9
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to TFT and IFACE devices
87
5.2.5.8 SSR_SetUserTmpExt
VARIANT_BOOL SSR_SetUserTmpExt(LONG dwMachineNumber, LONG IsDeleted,
BSTR dwEnrollNumber, LONG dwFingerIndex, BYTE* TmpData)
To upload a fingerprint template. This function is an enhanced version of SSR_SetUserTmp.
Parameters
Parameter description:
name
type param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
IsDeleted
LONG
[in]
Deletion flag
dwEnrollNumber
BSTR
[in]
User ID
dwFingerIndex
LONG
[in]
Fingerprint index, ranging
from 0 to 9
TmpData
BYTE*
[in]
Fingerprint template
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
IsDeleted is a deletion flag. If a fingerprint with the specified index already exists on the machine
when you upload a fingerprint template, this parameter specifies whether to overwrite the
original fingerprint. The value 1 indicates overwriting the original fingerprint and 0 indicates not
overwriting the original fingerprint.
Note
Applicable to TFT and IFACE devices
5.2.5.9 SSR_DelUserTmpExt
VARIANT_BOOL SSR_DelUserTmpExt(LONG dwMachineNumber, BSTR dwEnrollNumber,
LONG dwFingerIndex)
88
Deletes the specified fingerprint template for the specified user.
Parameters
Parameter description:
name
type param direction
description of param
dwMachineNumber LONG
[in]
Machine ID
dwEnrollNumber
BSTR
[in]
User ID
dwFingerIndex
LONG
[in]
Fingerprint template ID of the
specified user
Returns
Value description:
name type
True
description of value
BOOL Function execution success
False BOOL Function execution failure
See also
Attention
Note
Applicable to TFT devices
5.2.5.10 SetUserTmp
VARIANT_BOOL SetUserTmp(LONG dwMachineNumber, LONG dwEnrollNumber, LONG
dwFingerIndex, BYTE* TmpData)
To upload a fingerprint template in binary format. This function differs from SetUserTmpStr only
in the fingerprint template format.
Parameters
Parameter description:
name
type param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
dwEnrollNumber
LONG
[in]
User ID
89
dwFingerIndex
LONG
[in]
Fingerprint index
TmpData
BYTE*
[in]
Fingerprint template data
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
The user must already exist on the machine. If the index number of a user has been registered, the
fingerprint template will be overwritten.
Note
Applicable to BW
5.2.5.11 SetUserTmpStr
VARIANT_BOOL SetUserTmpStr(LONG dwMachineNumber, LONG dwEnrollNumber,
LONG dwFingerIndex, BSTR TmpData)
To obtain a fingerprint template in character string format. This function differs from
SetUserTmp only in the fingerprint template format.
Parameters
Parameter description:
name
type param direction
description of param
dwMachineNumber LONG
[in]
Machine ID
dwEnrollNumber
LONG
[in]
User ID
dwFingerIndex
LONG
[in]
Fingerprint index
TmpData
BSTR
[in]
Fingerprint template
Returns
Value description:
90
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
The user must already exist on the machine. If the index number of a user has been registered, the
fingerprint template will be overwritten.
Note
Applicable to BW
5.2.5.12 SetUserTmpEx
VARIANT_BOOL SetUserTmpEx(LONG dwMachineNumber,
LONG dwEnrollNumber, LONG dwFingerIndex, LONG Flag, BYTE* TmpData)
To upload fingerprint template ZKFinger 10.0 in binary format.
Parameters
Parameter description:
name
type param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
dwEnrollNumber
LONG
[in]
User ID
dwFingerIndex
LONG
[in]
Fingerprint index
Flag
LONG
[in]
Flag that indicates whether
the fingerprint template is
valid or a duress
fingerprint
TmpData
BYTE*
[in]
Fingerprint template data
Returns
Value description:
name type
description of value
91
True
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
1. The machine firmware must support the duress fingerprint function. That is, the internal
version of the firmware must be Ver6.60 or later.
2. The Flag parameter specifies whether the fingerprint template is valid or a duress fingerprint.
The value 0 indicates that the fingerprint template is invalid, 1 indicates that the fingerprint
template is valid, and 3 indicates that the fingerprint template is a duress fingerprint.
Note
Applicable to BW, TFT and IFACE devices
5.2.5.13 SetUserTmpExStr
VARIANT_BOOL SetUserTmpExStr(LONG dwMachineNumber, LONG dwEnrollNumber,
LONG dwFingerIndex, LONG Flag, BSTR TmpData)
To upload fingerprint template ZKFinger 10.0 in character string format.
Parameters
Parameter description:
name
type param direction
description of param
dwMachineNumber LONG
[in]
Machine ID
dwEnrollNumber
LONG
[in]
User ID
dwFingerIndex
LONG
[in]
Fingerprint index
Flag
LONG
[in]
Flag that indicates whether the
fingerprint template is valid or
a duress fingerprint
TmpData
BSTR
[in]
Fingerprint template
Returns
Value description:
name type
True
BOOL
description of value
Function execution success
92
False BOOL
Function execution failure
See also
Attention
1. The machine firmware must support the duress fingerprint function. That is, the internal
version of the firmware must be Ver6.60 or later.
2. The Flag parameter specifies whether the fingerprint template is valid or a duress fingerprint.
The value 0 indicates that the fingerprint template is invalid, 1 indicates that the fingerprint
template is valid, and 3 indicates that the fingerprint template is a duress fingerprint.
Note
Applicable to BW, TFT and IFACE devices
5.2.5.14 GetUserTmp
VARIANT_BOOL GetUserTmp(LONG dwMachineNumber, LONG dwEnrollNumber,
LONG dwFingerIndex, BYTE* TmpData, LONG* TmpLength )
To obtain a fingerprint template in binary format. This function differs from GetUserTmpStr only
in the fingerprint template format.
Parameters
Parameter description:
name
type param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
dwEnrollNumber
LONG
[in]
User ID
dwFingerIndex
LONG
[in]
Fingerprint index
TmpData
BYTE*
[out]
Fingerprint template data
TmpLength
LONG*
[out]
Length of the fingerprint
template
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
93
See also
Attention
Note
Applicable to BW
5.2.5.15 GetUserTmpStr
VARIANT_BOOL GetUserTmpStr(LONG dwMachineNumber, LONG dwEnrollNumber,
LONG dwFingerIndex, BSTR* TmpData, LONG* TmpLength)
To obtain a fingerprint template in character string format. This function differs from
GetUserTmp only in the fingerprint template format.
Parameters
Parameter description:
name
type
param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
dwEnrollNumber
LONG
[in]
User ID
dwFingerIndex
LONG
[in]
Fingerprint index
TmpData
BSTR*
[out]
Fingerprint template data
TmpLength
LONG*
[out]
Length of the fingerprint template
Returns
Value description:
name
type
description of value
True
BOOL
Function execution success
False
BOOL
Function execution failure
See also
Attention
Note
Applicable to BW
94
5.2.5.16 GetUserTmpEx
VARIANT_BOOL GetUserTmpEx(LONG dwMachineNumber, BSTR dwEnrollNumber,
LONG dwFingerIndex, LONG* Flag, BYTE* TmpData, LONG* TmpLength)
To obtain fingerprint template ZKFinger 10.0 in binary format.
Parameters
Parameter description:
name
type
param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
dwEnrollNumber
BSTR
[in]
User ID
dwFingerIndex
LONG
[in]
Fingerprint index
Flag
LONG*
[out]
Flag that indicates whether the
fingerprint template is valid or a
duress fingerprint
TmpData
BYTE*
[out]
Fingerprint template
TmpLength
LONG*
[out]
Length of the fingerprint template
Returns
Value description:
name
type
description of value
True
BOOL
Function execution success
False
BOOL
Function execution failure
See also
Attention
1. The machine firmware must support the duress fingerprint function. That is, the internal
version of the firmware must be Ver6.60 or later.
The Flag parameter specifies whether the fingerprint template is valid or a duress fingerprint. The
value 0 indicates that the fingerprint template is invalid, 1 indicates that the fingerprint template
is valid, and 3 indicates that the fingerprint template is a duress fingerprint.
Note
Applicable to BW, TFT and IFACE devices
95
5.2.5.17 GetUserTmpExStr
VARIANT_BOOL GetUserTmpExStr(LONG dwMachineNumber, BSTR dwEnrollNumber,
LONG dwFingerIndex, LONG* Flag, BSTR* TmpData, LONG* TmpLength)
To obtain fingerprint template ZKFinger 10.0 in character string format.
Parameters
Parameter description:
name
type
param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
dwEnrollNumber
BSTR
[in]
User ID
dwFingerIndex
LONG
[in]
Fingerprint index
Flag
LONG*
[out]
Flag that indicates
whether the fingerprint
template is valid or a
duress fingerprint
TmpData
BSTR*
[out]
Fingerprint template
TmpLength
LONG*
[out]
Length of the
fingerprint template
Returns
Value description:
name
type
description of value
True
BOOL
Function execution success
False
BOOL
Function execution failure
See also
Attention
1. The machine firmware must support the duress fingerprint function. That is, the internal
version of the firmware must be Ver6.60 or later.
2. The Flag parameter specifies whether the fingerprint template is valid or a duress fingerprint.
The value 0 indicates that the fingerprint template is invalid, 1 indicates that the fingerprint
template is valid, and 3 indicates that the fingerprint template is a duress fingerprint.
Note
96
Applicable to BW, TFT and IFACE devices
5.2.5.18 GetFPTempLength
VARIANT_BOOL GetFPTempLength(BYTE* dwEnrollData, LONG* Len)
To calculate length of a specified fingerprint template.
Parameters
Parameter description:
name
type
param direction
description of param
dwEnrollData
BYTE*
[in]
Pointer that points to the
fingerprint template
[out]
The value is the fingerprint
template length described
by dwEnrollData.
Len
LONG*
Returns
Value description:
name
type
description of value
True
BOOL
Function execution success
False
BOOL
Function execution failure
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
5.2.5.19 GetFPTempLengthStr
VARIANT_BOOL GetFPTempLengthStr(BSTR dwEnrollData, LONG* Len)
To calculate length of a specified fingerprint template.
Parameters
Parameter description:
name
type
param direction
97
description of param
dwEnrollData
BSTR
[in]
Fingerprint template in character
string format
Len
LONG*
[out]
The value is the fingerprint template
length described by dwEnrollData.
Returns
Value description:
name
type
description of value
True
BOOL
Function execution success
False
BOOL
Function execution failure
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
5.2.5.20 FPTempConvert
VARIANT_BOOL FPTempConvert(BYTE* TmpData1, BYTE* TmpData2, LONG* Size)
To convert an offline fingerprint template into a BIOKEY fingerprint template. This function
differs from FPTempConvertStr only in the data format.
Parameters
Parameter description:
name
type
param direction
description of param
TmpData1
BYTE*
[in]
Offline fingerprint template to be
converted
TmpData2
BYTE*
[out]
The value is the BIOKEY fingerprint
template after conversion.
Size
LONG*
[out]
The value is the size of the BIOKEY
fingerprint template after conversion.
Returns
Value description:
98
name
type
description of value
True
BOOL
Function execution success
False
BOOL
Function execution failure
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
5.2.5.21 FPTempConvertStr
VARIANT_BOOL FPTempConvertStr(BSTR TmpData1, BSTR* TmpData2, LONG* Size)
To convert an offline fingerprint template into a BIOKEY fingerprint template in character string
format. This function differs from FPTempConvert only in the data format.
Parameters
Parameter description:
name
type
param direction
description of param
TmpData1
BSTR
[in]
Offline fingerprint template to be
converted
TmpData2
BSTR*
[out]
The value is the BIOKEY fingerprint
template after conversion.
Size
LONG*
[out]
The value is the size of the BIOKEY
fingerprint template after conversion.
Returns
Value description:
name
type
description of value
True
BOOL
Function execution success
False
BOOL
Function execution failure
See also
99
Attention
Note
Applicable to BW, TFT and IFACE devices
5.2.5.22 FPTempConvertNew
VARIANT_BOOL FPTempConvertNew(BYTE* TmpData1, BYTE* TmpData2, LONG* Size)
To convert a BIOKEY fingerprint template into an offline fingerprint template. This function
differs from FPTempConvertNewStr only in the data format.
Parameters
Parameter description:
name
type
param direction
description of param
TmpData1
BYTE*
[in]
Offline fingerprint template to be
converted
TmpData2
BYTE*
[out]
The value is the offline fingerprint
template after conversion.
Size
LONG*
[out]
The value is the size of the offline
fingerprint template after conversion.
Returns
Value description:
name
type
description of value
True
BOOL
Function execution success
False
BOOL
Function execution failure
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
5.2.5.23 FPTempConvertNewStr
VARIANT_BOOL FPTempConvertNewStr(BSTR TmpData1, BSTR* TmpData2, LONG* Size)
To convert a BIOKEY fingerprint template into an offline fingerprint template in character string
format. This function differs from FPTempConvertNew only in the data format.
Parameters
100
Parameter description:
name
type
param direction
description of param
TmpData1
BSTR
[in]
Offline fingerprint template to be
converted
TmpData2
BSTR*
[out]
The value is the offline fingerprint
template after conversion.
Size
LONG*
[out]
The value is the size of the offline
fingerprint template after conversion.
Returns
Value description:
name
type
description of value
True
BOOL
Function execution success
False
BOOL
Function execution failure
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
5.2.6
Face Template Functions
5.2.6.1 SetUserFace
VARIANT_BOOL SetUserFace(LONG dwMachineNumber, BSTR dwEnrollNumber, LONG
dwFaceIndex, BYTE* TmpData, LONG TmpLength)
To upload a face template. This function differs from SetUserFaceStr only in the face template
format.
Parameters
Parameter description:
name
type
param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
101
dwEnrollNumber
BSTR
[in]
User ID (not more than 24
digits)
dwFaceIndex
LONG
[in]
Face index
TmpData
BYTE*
[in]
Face template
TmpLength
LONG
[in]
Length of the face template
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
The value of dwFaceIndex is always 50, which indicates uploading all face templates of a user.
Note
Applicable to IFACE
5.2.6.2 GetUserFace
VARIANT_BOOL GetUserFace(LONG dwMachineNumber, BSTR dwEnrollNumber,
LONG dwFaceIndex, BYTE* TmpData, LONG* TmpLength)
To download a face template. This function differs from GetUserFaceStr only in the face
template format.
Parameters
Parameter description:
name
type param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
dwEnrollNumber
BSTR
[in]
User ID (not more than 24 digits)
dwFaceIndex
LONG
[in]
Face index
TmpData
BYTE*
[out]
Face template
102
TmpLength
LONG*
[out]
Length of the face template
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
The value of dwFaceIndex is always 50, which indicates downloading all face templates of a
user.
Note
Applicable to IFACE
5.2.6.3 DelUserFace
VARIANT_BOOL DelUserFace(LONG dwMachineNumber, BSTR dwEnrollNumber,
LONG dwFaceIndex)
To delete a face template.
Parameters
Parameter description:
name
type param direction
description of param
dwMachineNumber LONG
[in]
Machine ID
dwEnrollNumber
BSTR
[in]
User ID (not more than 24 digits)
dwFaceIndex
LONG
[in]
Face index
Returns
Value description:
name type
True
BOOL
description of value
Function execution success
103
False BOOL
Function execution failure
See also
Attention
The value of dwFaceIndex is always 50, which indicates downloading all face templates of a
user.
Note
Applicable to IFACE
5.2.6.4 GetUserFaceStr
VARIANT_BOOL GetUserFaceStr(LONG dwMachineNumber, BSTR dwEnrollNumber,
LONG dwFaceIndex, BSTR* TmpData, LONG* TmpLength)
To download a face template. This function differs from GetUserFace in that it returns a face
template in character string format.
Parameters
Parameter description:
name
type param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
dwEnrollNumber
BSTR
[in]
User ID (not more than 24
digits)
dwFaceIndex
LONG
[in]
Face index
TmpData
BSTR*
[out]
Face template
TmpLength
LONG*
[out]
Length of the face template
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
104
Attention
The value of dwFaceIndex is always 50, which indicates downloading all face templates of a
user.
Note
Applicable to IFACE
5.2.6.5 SetUserFaceStr
VARIANT_BOOL SetUserFaceStr(LONG dwMachineNumber, BSTR dwEnrollNumber,
LONG dwFaceIndex, BSTR TmpData, LONG TmpLength)
To upload a face template. This function differs from SetUserFace only in the face template
format.
Parameters
Parameter description:
name
type param direction
description of param
dwMachineNumber LONG
[in]
Machine ID
dwEnrollNumber
BSTR
[in]
User ID (not more than 24 digits)
dwFaceIndex
LONG
[in]
Face index
TmpData
BSTR
[in]
Face template
TmpLength
LONG
[in]
Length of the face template
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
The value of dwFaceIndex is always 50, which indicates uploading all face templates of a user.
Note
Applicable to IFACE
105
5.2.7
User Verify Functions
5.2.7.1 SetUserVerifyStyle
VARIANT_BOOL SetUserVerifyStyle(LONG dwMachineNumber, BSTR dwEnrollNumber,
LONG VerifyStyle, BYTE* Reserved)
To set the user verification mode.
Parameters
Parameter description:
name
type param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
dwEnrollNumber
BSTR
[in]
User ID
VerifyStyle
LONG
[in]
Verification mode
Reserved
BSTR*
[in]
Reserved
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
1. The VerifyStyle parameter specifies the verification mode. The values are described as follows:
Group Verify = 0
FP/PW/RF = 128
FP = 129
PIN = 130
PW = 131
RF = 132
FP/PW = 133
FP/RF = 134
PW/RF = 135
PIN&FP = 136
106
FP&PW = 137
FP&RF = 138
PW&RF = 139
FP&PW&RF = 140
PIN&FP&PW = 141
FP&RF/PIN = 142
2. The Reserved parameter is reserved and not used at present.
Note
This interface is applicable to the new architecture firmware.
5.2.7.2 GetUserVerifyStyle
VARIANT_BOOL GetUserVerifyStyle(LONG dwMachineNumber, BSTR dwEnrollNumber,
LONG* VerifyStyle, BYTE* Reserved)
To obtain the user verification mode.
Parameters
Parameter description:
name
type param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
dwEnrollNumber
BSTR
[in]
User ID
VerifyStyle
LONG*
[out]
Verification mode
Reserved
BSTR*
[out]
Reserved
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
1. The VerifyStyle parameter specifies the verification mode. The values are described as follows:
Group Verify = 0
FP/PW/RF = 128
107
FP = 129
PIN = 130
PW = 131
RF = 132
FP/PW = 133
FP/RF = 134
PW/RF = 135
PIN&FP = 136
FP&PW = 137
FP&RF = 138
PW&RF = 139
FP&PW&RF = 140
PIN&FP&PW = 141
FP&RF/PIN = 142
2. The Reserved parameter is reserved and not used at present.
Note
This interface is applicable to the new architecture firmware.
5.2.8
Shortcut Keys Functions
5.2.8.1 SSR_SetShortkey
VARIANT_BOOL SSR_SetShortkey(LONG ShortKeyID, LONG ShortKeyFun, LONG
StateCode, BSTR StateName, LONG StateAutoChange, BSTR StateAutoChangeTime)
To set a functional key. It is similar to the functional key definition function on the color-screen
machine.
Parameters
Parameter description:
name
type param direction
description of param
ShortKeyID
LONG
[in]
Key ID
ShortKeyFun
LONG
[in]
Function of the key
StateCode
LONG
[in]
State code of the status key
StateName
BSTR
[in]
Name of the status key
StateAutoChange
LONG
[in]
Auxiliary
StateAutoChangeTime BSTR
[in]
Auxiliary
Returns
108
Value description:
name
type description of value
True
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
1. ShortKeyID: specifies the ID of the key. The mapping is as follows: F1 ? 1, F2 ? 2, F3 ? 3 ...
2. ShortKeyFun: function of the specified key. The value 0 indicates that the function of the key
is not defined, 1 indicates that the specified key is a status key, 2 indicates the work code of the
key, and 3 indicates viewing the short message. Note: the value of ShortKeyFun will influence
settings of the following four parameters. Please refer to the below instructions.
3. StateCode: To set state code of specified status key. If the specified key is not a status key
(namely, the value of ShortKeyFun is not 1), the value of StateCode will be ignored. If the
specified key is a status key (ShortKeyFun=1), the state code of the specified status key is
determined by the StateCode value, which ranges from 0 to 255.The state code of status key
cannot be repeatedly, if the state code of different status key is set as the same, invoking of
StateCode will fail. Such as F2 is a status key and the state code is 2; while you invoke StateCode
Fun to set F3 as a status key and set its state code as 2, the invoking will fail.
4. StateName: To set name of status key. If the specified key is not a status key (namely, the value
of ShortKeyFun is not 1), the value of StateName will be ignored. If the specified key is a status
key (ShortKeyFun=1), the name of specified status key will be determined by the StateName
value. At most, 18 characters are supported.
5. StateAutoChange: If the specified key is not a status key (namely, the value of ShortKeyFun is
not 1), the value of StateAutoChange will be ignored. If the specified key is a status key
(ShortKeyFun=1), the value of StateAutoChange indicates whether the status key automatically
changes. 0: disable, 1: enable.
6. StateAutoChangeTime: If the specified key is not a status key (namely, the value of
ShortKeyFun is not 1), the value of StateAutoChangeTime will be ignored. If the specified key is
a status key (ShortKeyFun=1), the automatic change time of the status key is set by the return
value of StateAutoChangeTime. Requirements as below:
1) "08:30;09:00;08:00;12:00;11:12;00:00;00:00;".
2) Hour and minute are separated with ":",Dates are separated with ";",space is not allowed
between them.
3) Everyday's automatic change time shall be specified(one whole week is a cycle), reaches
which the attendance state will change to specified state automatically (the name of automatic
change state is decided by StateName, value is defined by the return value of StateCode). If
109
someday needs not to change attendance state automatically, set hour and minute of the
StateAutoChangeTime as zero.
Note
Applicable to TFT
5.2.8.2 SSR_GetShortkey
VARIANT_BOOL SSR_GetShortkey(LONG ShortKeyID, LONG* ShortKeyFun, LONG*
StateCode, BSTR* StateName, LONG* AutoChange, BSTR* AutoChangeTime)
To query the settings of a functional key.
Parameters
Parameter description:
name
type param direction
description of param
ShortKeyID
LONG
[in]
Key ID
ShortKeyFun
LONG*
[out]
Function of the key
StateCode
LONG*
[out]
State code of the status key
StateName
BSTR*
[out]
Name of the status key
AutoChange
LONG*
[out]
Whether the status key
automatically changes
AutoChangeTime BSTR*
[out]
Automatic change time of the status
key
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
1. ShortKeyID: specifies the ID of the key. The mapping is as follows: F1 ? 1, F2 ? 2, F3 ? 3 ...
2. ShortKeyFun: function of the specified key. The value 0 indicates that the function of the key
is not defined, 1 indicates that the specified key is a status key, 2 indicates the work code of the
110
key, and 3 indicates viewing the short message.
3. StateCode: If the specified key is a status key (ShortKeyFun=1), the state code of the status
key is returned. Otherwise, 0 is returned.
4. StateName: If the specified key is a status key (ShortKeyFun=1), the name of the status key is
returned. Otherwise, a blank character string is returned.
5. AutoChange: If the specified key is a status key (ShortKeyFun=1), the value of this parameter
indicates whether the status key automatically changes. Otherwise, 0 is returned.
6. AutoChangeTime: If the specified key is a status key (ShortKeyFun=1), the automatic change
time of the status key is returned, in the format of a character string. Otherwise, a blank character
string is returned.
Note
Applicable to TFT
5.2.8.3 EnableCustomizeAttState
VARIANT_BOOL EnableCustomizeAttState(LONG dwMachineNumber, LONG StateID,
LONG Enable)
To specify whether to enable a customized attendance status value.
Parameters
Parameter description:
name
type param direction
dwMachineNumber LONG
StateID
Enable
LONG
LONG
description of param
[in]
Machine ID
[in]
Attendance status value to be defined
[in]
Whether to enable the attendance
status definition function for the
attendance status value specified by
StateID
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
111
See also
Attention
1. This function is a customization function. To use this function, the extension function must be
enabled for the machine and the machine must support the attendance status definition function.
2. Attendance status definition function: The mapping between the attendance status values and
the states are as follows:
If this function is enabled, you can invoke SetCustomizeAttState to change the status value of a
state: 0-Check-In 1-Check-Out 2-Break-Out 3-Break-In 4-OT-In 5-OT-Out
For example, EnableCustomizeAttState(1,0,1)// indicates enabling the customized state of 0
(check-in)
SetCustomizeAttState(1,0,8)// indicates setting the customized status value to 8 for the status
value 0 (check-in)
If a user chooses check-in on the machine and passes verification, the saved attendance status
value is 8.
Note
Applicable to BW
5.2.8.4 SetCustomizeAttState
VARIANT_BOOL SetCustomizeAttState(LONG dwMachineNumber, LONG StateID,
LONG NewStatel)
To set a customized attendance status value based on the original attendance status value.
Parameters
Parameter description:
name
type param direction
dwMachineNumber LONG
description of param
[in]
Machine ID
StateID
LONG
[in]
Original status value
NewStatel
LONG
[in]
New status value
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
112
See also
Attention
This function is a customization function. To use this function, the extension function must be
enabled for the machine and the machine must support the attendance status definition function.
For details, see the description of EnableCustomizeAttState.
Note
Applicable to BW
5.2.8.5 DelCustomizeAttState
VARIANT_BOOL DelCustomizeAttState(LONG dwMachineNumber, LONG StateID)
To delete the customized attendance status value of an original attendance status value.
Parameters
Parameter description:
name
type param direction
dwMachineNumber LONG
StateID
LONG
description of param
[in]
Machine ID
[in]
Original attendance status value
of which the customized attendance
value is to be deleted
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
This function is a customization function. To use this function, the extension function must be
enabled for the machine and the machine must support the attendance status definition function.
For details, see the description of EnableCustomizeAttState.
Note
Applicable to BW
113
5.2.8.6 GetAllSFIDName
VARIANT_BOOL GetAllSFIDName(LONG dwMachineNumber, BSTR* ShortkeyIDName,
LONG BufferSize1, BSTR* FunctionIDName, LONG BufferSize2)
To query the shortcut key name and function lists.
Parameters
Parameter description:
name
type param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
ShortkeyIDName
BSTR*
[out]
List of shortcut key IDs and
names
BufferSize1
LONG
[in]
Size of the buffer for storing
the list of shortcut key IDs
and names
FunctionIDName
BSTR*
[out]
List of function IDs and names
[in]
Size of the buffer for storing
the list of function IDs and
names
BufferSize2
LONG
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
1. ShortkeyIDName: specifies the list of shortcut key IDs and names, in the format of
"ID,Key_Name\r\n1,F1\r\n2,F2...".
2. FunctionIDName: specifies the list of function IDs and names, in the format of
"ID,Func_Name\r\n1,adduser\r\n2,userlist...".
3. The values of BufferSize1 and BufferSize2 are est to 4 kB.
114
Note
This interface is applicable to the new architecture firmware.
5.2.8.7 GetShortkey
VARIANT_BOOL GetShortkey(LONG dwMachineNumber, LONG ShortKeyID,
BSTR* ShortKeyName, BSTR* FunctionName, LONG* ShortKeyFun, LONG* StateCode,
BSTR* StateName, BSTR* Description, LONG* AutoChange, BSTR* AutoChangeTime)
To query the settings of a functional key.
Parameters
Parameter description:
name
type
param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
ShortKeyID
LONG
[in]
Key ID
ShortKeyName
BSTR*
[out]
Key name
ShortKeyName
BSTR*
[out]
Function name of the key
ShortKeyFun
LONG*
[out]
Key type
StateCode
LONG*
[out]
State code of the status key
StateName
BSTR*
[out]
Name of the status key
Description
BSTR*
[out]
Description of the status key
AutoChange
LONG*
[out]
Whether the status key
automatically changes
AutoChangeTime
BSTR*
[out]
Automatic change time of the
status key
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
115
See also
Attention
1. The mapping between ShortKeyName and ShortKeyID is as follows: F1-1, F2 -2, F3 -3 ...
2. ShortKeyFun: function of the specified key. The value 0 indicates a functional key and 1
indicates a status key.
3. ShortKeyName: name of the key specified by ShortKeyID.
4. FunctionName: If the specified key is a functional key (ShortKeyFun=0), the function name is
returned.
5. FunctionName: If the specified key is a status key (ShortKeyFun=1), the name of the key is
returned. In this case, the value of FunctionName is the same as that of StateName.
6. StateCode: If the specified key is a status key (ShortKeyFun=1), the state code of the status
key is returned. Otherwise, an invalid value is returned.
7. StateName: If the specified key is a status key (ShortKeyFun=1), the name of the status key is
returned. Otherwise, an invalid value is returned.
8. AutoChange: If the specified key is a status key (ShortKeyFun=1), the value of this parameter
indicates whether the status key automatically changes. Otherwise, an invalid value is returned.
9. Description: If the specified key is a status key (ShortKeyFun=1), the description of the status
key is returned. Otherwise, an invalid value is returned.
10. AutoChangeTime: If the specified key is a status key (ShortKeyFun=1), the automatic change
time of the status key is returned, in the format of a character string. Otherwise, an invalid value
is returned.
Note
This interface is applicable to the new architecture firmware.
5.2.8.8 SetShortkey
VARIANT_BOOL SetShortkey(LONG dwMachineNumber, LONG ShortKeyID, BSTR
ShortKeyName, BSTR FunctionName, LONG ShortKeyFun, LONG StateCode, BSTR
StateName, BSTR Description, LONG StateAutoChange, BSTR StateAutoChangeTime)
To set a functional key. It is similar to the functional key definition function on the color-screen
machine.
Parameters
Parameter description:
name
type param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
ShortKeyID
LONG
[in]
Key ID
116
ShortKeyName
BSTR
[in]
Key name
FunctionName
BSTR
[in]
Function name of the key
ShortKeyFun
LONG
[in]
Key type
StateCode
LONG
[in]
State code of the status key
StateName
BSTR
[in]
Name of the status key
Description
BSTR
[in]
Description of the status key
AutoChange
LONG
[in]
Whether the status key automatically
changes
AutoChangeTime
BSTR
[in]
Automatic change time of the status key
Returns
Value description:
name
type
description of value
True
BOOL
Function execution success
False
BOOL
Function execution failure
See also
Attention
1. When setting ShortKeyName and ShortKeyID, ensure that the mapping between
ShortKeyName and ShortKeyID is as follows: F1-1, F2 -2, F3-3 ...
2. ShortKeyFun: function of the specified key. The value 0 indicates a functional key and 1
indicates a status key. Note that the value of this parameter will affect the settings of other four
parameters.
3. StateCode: state code of the status key.
If the specified key is not a functional key, that is, the value of ShortKeyFun is not 1, the value of
this parameter will be ignored.
If the specified key is a status key, that is, the value of ShortKeyFun is 1, the value of this
parameter is the state code of the status key, and ranges from 0 to 255. The state values of status
keys cannot be duplicate. Otherwise, function invocation will fail. For example, F2 is a status key
and its state code is 2. If you invoke this function to set F3 as a status key and set its state code to
2, the function invocation will fail.
4. StateName: name of the status key.
117
If the specified key is not a functional key, that is, the value of ShortKeyFun is not 1, the value of
this parameter will be ignored.
If the specified key is a status key, that is, the value of ShortKeyFun is 1, the value of this
parameter is the name of the status key, and contains at most 18 characters.
5. Description: description of the status key.
If the specified key is not a functional key, that is, the value of ShortKeyFun is not 1, the value of
this parameter will be ignored.
If the specified key is a status key, that is, the value of ShortKeyFun is 1, the value of this
parameter is the description of the status key.
6. StateAutoChange: whether the status key automatically changes:
If the specified key is not a functional key, that is, the value of ShortKeyFun is not 1, the value of
this parameter will be ignored.
If the specified key is a status key, that is, the value of ShortKeyFun is 1, the value of this
parameter indicates whether the status key automatically changes. The value 0 indicates that the
status key automatically changes and 1 indicates that the status key does not automatically
change.
7. StateAutoChangeTime:
If the specified key is not a functional key, that is, the value of ShortKeyFun is not 1, the value of
this parameter will be ignored.
If the specified key is a status key, the value of this parameter is the automatic change time of the
status key. The details are as follows: 1. 08:30;09:00;08:00;12:00;11:12;00:00;00:00; 2. The hour
is separated from the minute with a colon (:), and days are separated with a semicolon (;), free
from spaces. 3. You must specify the automatic change time of each day, with a week as a cycle.
After the specified time arrives, the attendance status will change to the state specified by
StateName and StateCode. If automatic change is disabled on a day, the hour and minute are both
set to 0.
8. If the return value of issued status key is -15001 repeatedly, the return value of description will
be -15002 repeatedly.
Note
This interface is applicable to the new architecture firmware.
5.2.9
Work Code Functions
5.2.9.1 SetWorkCode
VARIANT_BOOL SetWorkCode(LONG WorkCodeID, LONG AWorkCode)
To define a work code with a specified ID.
Parameters
Parameter description:
name
type param direction
description of param
118
WorkCodeID LONG
[in]
Work code ID
AWorkCode
[in]
Value of work code described by WorkCodeID
LONG
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
A work code value within any range can be input on a monochrome machine. After the work
code is defined by using this function, the user can input only the defined work code. For
example, if the work code is defined as SetWorkCode(1,345) and SetWorkCode(2,567), the user
can input only the work code with the values 345 and 567.
Note
Applicable to BW
5.2.9.2 GetWorkCode
VARIANT_BOOL GetWorkCode(LONG WorkCodeID, LONG* AWorkCode)
To obtain the name of a specified work code ID. For details, see the description of SetWorkCode.
Parameters
Parameter description:
name
type param direction
description of param
WorkCodeID
LONG
[in]
Work code ID
AWorkCode
LONG*
[out]
Obtained value of work code
described by WorkCodeID
Returns
Value description:
name type
description of value
119
True
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to BW
5.2.9.3 SSR_GetWorkCode
VARIANT_BOOL SSR_GetWorkCode(LONG AWorkCode, BSTR* Name)
To obtain the name of a specified work code ID.
Parameters
Parameter description:
name
type param direction
description of param
AWorkCode
LONG
[in]
Work code ID
Name
BSTR*
[out]
Obtained value of work code
described by WorkCodeID
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to TFT
5.2.9.4 SSR_SetWorkCode
VARIANT_BOOL SSR_SetWorkCode(LONG AWorkCode, BSTR Name)
To set a work code with a specified ID.
Parameters
120
Parameter description:
name
type param direction
AWorkCode LONG
Name
BSTR
description of param
[in]
Work code ID
[in]
Value of work code described
by WorkCodeID
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to TFT
5.2.9.5 SSR_DeleteWorkCode
VARIANT_BOOL SSR_DeleteWorkCode(LONG AWorkCode)
To delete a work code with a specified ID.
Parameters
Parameter description:
name
type param direction description of param
AWorkCode LONG
[in]
Work code ID
Returns
Value description:
name type
True
BOOL
description of value
Function execution success
121
False BOOL
Function execution failure
See also
Attention
Note
Applicable to TFT
5.2.9.6 SSR_ClearWorkCode
VARIANT_BOOL SSR_ClearWorkCode()
To delete all user-defined work codes.
Parameters
None
Returns
Value description:
name type
True
description of value
BOOL Function execution success
False BOOL Function execution failure
See also
Attention
Note
Applicable to TFT
5.2.9.7 DeleteWorkCode
VARIANT_BOOL DeleteWorkCode(LONG WorkCodeID)
To delete a work code with a specified work code ID. For details, see the description of
SetWorkCode.
Parameters
Parameter description:
name
type param direction description of param
WorkCodeID LONG
[in]
Work code ID
Returns
Value description:
122
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to BW
5.2.9.8 ClearWorkCode
VARIANT_BOOL ClearWorkCode()
To clear all defined work codes on the machine. For details, see the description of SetWorkCode.
Parameters
None
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to BW
5.2.9.9 SSR_GetWorkCodeIDByName
VARIANT_BOOL SSR_GetWorkCodeIDByName(LONG dwMachineNumber, BSTR
WorkCodeName, LONG* WorkCodeId)
To query the interface of work code id based on the work code name.
Parameters
Parameter description:
123
name
type param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
WorkCodeName
BSTR
[in]
Work code name
WorkCodeId
LONG*
[out]
Work code ID
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Together with the interface of SSR_SetWorkCode, to judge whether the issued workname is
repeatedly (the same WorkCodeName cannot be issued). When return value of WorkCodeID is
greater than zero, the issued workname has existed.
Note
This interface is applicable to the new architecture firmware.
5.2.10
SMS Functions
5.2.10.1 SetSMS
VARIANT_BOOL SetSMS(LONG dwMachineNumber, LONG ID, LONG Tag,
LONG ValidMinutes, BSTR StartTime, BSTR Content)
To add a short message to the machine. To set the short message for a user, invoke SetUserSMS
to assign the short message to the user.
Parameters
Parameter description:
name
type param direction
dwMachineNumber LONG
ID
LONG
description of param
[in]
Machine ID
[in]
Short message ID
124
Tag
LONG
[in]
Short message type
ValidMinutes
LONG
[in]
Validity period of the short message
StartTime
BSTR
[in]
Effective time of the short message
Content
BSTR
[in]
Content of the short message
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
1. Tag specifies the short message type. The value 253 indicates public short message, 254
personal short message, and 255 reserved short message.
2. ValidMinutes specifies the validity period of the short message. The value ranges from 0 to
65535. The short message will take effect at the time specified by StartTime and will last for a
period of time specified by ValidMinutes.
3. StartTime specifies the effective time of the short message, in the format of yyyy-mm-dd
hh:mm:ss.
Note
Applicable to BW and TFT devices
5.2.10.2 SetUserSMS
VARIANT_BOOL SetUserSMS(LONG dwMachineNumber, LONG dwEnrollNumber,
LONG SMSID)
To set the short message of a user. Specifically, this function is used to assign a short message
with a specific ID to a user.
Parameters
Parameter description:
name
type param direction
dwMachineNumber LONG
description of param
[in]
Machine ID
125
dwEnrollNumber
LONG
[in]
User ID
SMSID
LONG
[in]
Short message ID
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to BW
5.2.10.3 SSR_SetUserSMS
VARIANT_BOOL SSR_SetUserSMS(LONG dwMachineNumber, BSTR dwEnrollNumber,
LONG SMSID)
To set the short message of a user. Specifically, this function is used to assign a short message
with a specific ID to a user.
Parameters
Parameter description:
name
type param direction
description of param
dwMachineNumber LONG
[in]
Machine ID
dwEnrollNumber
BSTR
[in]
User ID
SMSID
LONG
[in]
Short message ID
Returns
Value description:
name type
True
BOOL
description of value
Function execution success
126
False BOOL
Function execution failure
See also
Attention
Note
Applicable to TFT
5.2.10.4 GetSMS
VARIANT_BOOL GetSMS(LONG dwMachineNumber, LONG ID, LONG* Tag, LONG*
ValidMinutes, BSTR* StartTime, BSTR* Content)
To obtain details about a short message from the machine based on the short message ID,
including the content, effective time, message type, and validity period.
Parameters
Parameter description:
name
type param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
ID
LONG
[in]
Short message ID
Tag
LONG*
[out]
Short message type
ValidMinutes
LONG*
[out]
Validity period of the short
message
StartTime
BSTR*
[out]
Effective time of the short
message
Content
BSTR*
[out]
Content of the short message
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
127
1. Tag specifies the short message type. The value 253 indicates public short message, 254
personal short message, and 255 reserved short message.
2. ValidMinutes specifies the validity period of the short message. The value ranges from 0 to
65535. The short message will take effect at the time specified by StartTime and will last for a
period of time specified by ValidMinutes.
3. StartTime specifies the effective time of the short message, in the format of yyyy-mm-dd
hh:mm:ss.
Note
Applicable to BW and TFT devices
5.2.10.5 DeleteSMS.
VARIANT_BOOL DeleteSMS(LONG dwMachineNumber, LONG ID)
To delete a short message with a specified ID from the machine.
Parameters
Parameter description:
name
type param direction
dwMachineNumber LONG
ID
LONG
description of param
[in]
Machine ID
[in]
Short message ID
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to BW and TFT devices
5.2.10.6 DeleteUserSMS
VARIANT_BOOL DeleteUserSMS(LONG dwMachineNumber, LONG dwEnrollNumber, LONG
SMSID)
To delete the short message with a specified ID for a specified user. Only the mapping
128
relationship between the user and the short message is deleted, and the short message is not
deleted.
Parameters
Parameter description:
name
type param direction
description of param
dwMachineNumber LONG
[in]
Machine ID
dwEnrollNumber
LONG
[in]
User ID
SMSID
LONG
[in]
Short message ID
Returns
Value description:
name type
True
description of value
BOOL Function execution success
False BOOL Function execution failure
See also
Attention
Note
Applicable to BW
5.2.10.7 SSR_DeleteUserSMS
VARIANT_BOOL SSR_DeleteUserSMS(LONG dwMachineNumber, BSTR dwEnrollNumber,
LONG SMSID)
To delete the short message with a specified ID for a specified user. Only the mapping
relationship between the user and the short message is deleted, and the short message is not
deleted.
Parameters
Parameter description:
name
type param direction
dwMachineNumber LONG
description of param
[in]
Machine ID
129
dwEnrollNumber
BSTR
[in]
User ID
SMSID
LONG
[in]
Short message ID
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to TFT
5.2.10.8 ClearUserSMS
VARIANT_BOOL ClearUserSMS(LONG dwMachineNumber)
To clear all mapping relationships between short messages and users. The short messages are not
deleted.
Parameters
Parameter description:
name
type param direction
dwMachineNumber LONG
description of param
[in]
Machine ID
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
130
Note
Applicable to BW and TFT devices
5.2.10.9 ClearSMS
VARIANT_BOOL ClearSMS(LONG dwMachineNumber)
To clear all short messages on the machine. All short messages will be deleted from the machine.
Parameters
Parameter description:
name
type param direction
dwMachineNumber LONG
description of param
[in]
Machine ID
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to BW and TFT devices
5.2.11
Holiday Functions
5.2.11.1 SetHoliday
VARIANT_BOOL SetHoliday(LONG dwMachineNumber, BSTR Holiday)
To set holidays.
Parameters
Parameter description:
name
type param direction
dwMachineNumber LONG
description of param
[in]
Machine ID
131
Holiday
BSTR
[in]
Holiday to be set
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
The Holiday parameter specifies holidays in the format of mmddmmdd. For example, 04140511
indicates a holiday that lasts from April 14 to May 11.
Note
Applicable to BW
5.2.11.2 GetHoliday
VARIANT_BOOL GetHoliday(LONG dwMachineNumber, BSTR* Holiday)
To query the holiday that is set on the machine.
Parameters
Parameter description:
name
type param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
Holiday
BSTR*
[out]
Holiday specified on the machine
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
132
Attention
The Holiday parameter specifies holidays in the format of mmddmmdd. For example, 04140511
indicates a holiday that lasts from April 14 to May 11.
Note
Applicable to BW
5.2.11.3 SSR_GetHoliday
VARIANT_BOOL SSR_GetHoliday(LONG dwMachineNumber, LONG HolidayID,
LONG* BeginMonth, LONG* BeginDay, LONG* EndMonth, LONG* EndDay, LONG*
TimeZoneID)
To query holiday settings on the machine based on the holiday ID.
Parameters
Parameter description:
name
type param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
HolidayID
LONG
[in]
Holiday ID
BeginMonth
LONG*
[out]
Start date of the holiday
BeginDay
LONG*
[out]
Start date of the holiday
EndMonth
LONG*
[out]
End date of the holiday
EndDay
LONG*
[out]
End date of the holiday
TimeZoneID
LONG*
[out]
Index of the time segment of the
holiday
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
133
Note
Applicable to TFT and IFACE devices
5.2.11.4 SSR_SetHoliday
VARIANT_BOOL SSR_SetHoliday(LONG dwMachineNumber, LONG HolidayID, LONG
BeginMonth, LONG BeginDay, LONG EndMonth, LONG EndDay, LONG TimeZoneID )
To set holidays.
Parameters
Parameter description:
name
type param direction
dwMachineNumber LONG
description of param
[in]
Machine ID
HolidayID
LONG
[in]
Holiday ID
BeginMonth
LONG
[in]
Start date of the holiday
BeginDay
LONG
[in]
Start date of the holiday
EndMonth
LONG
[in]
End date of the holiday
EndDay
LONG
[in]
Start date of the holiday
TimeZoneID
LONG
[in]
Index of the time segment of
the holiday
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to TFT and IFACE devices
134
5.2.12
DST Functions
5.2.12.1 SetDaylight
VARIANT_BOOL SetDaylight(LONG dwMachineNumber, LONG Support, BSTR BeginTime,
BSTR EndTime)
To set whether to enable DST, and the DST start time and end time.
Parameters
Parameter description:
name
type param direction
dwMachineNumber LONG
description of param
[in]
Machine ID
Support
LONG
[in]
Whether to enable DST
BeginTime
BSTR
[in]
DST start time
EndTime
BSTR
[in]
DST end time
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
1. The Support parameter specifies whether to enable DST. The value 1 indicates enabling DST
and 0 indicates disabling DST.
2. The values of BeginTime and EndTime are in the format of mm-dd hh:mm.
Note
Applicable to BW, TFT, and IFACE devices
5.2.12.2 GetDaylight
VARIANT_BOOL GetDaylight(LONG dwMachineNumber, LONG* Support, BSTR* BeginTime,
BSTR* EndTime)
To query the DST settings on the machine.
Parameters
135
Parameter description:
name
type param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
Support
LONG*
[out]
Whether to enable DST
BeginTime
BSTR*
[out]
DST start time
EndTime
BSTR*
[out]
DST end time
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
1. The Support parameter specifies whether to enable DST. The value 1 indicates enabling DST
and 0 indicates disabling DST.
2. The values of BeginTime and EndTime are in the format of mm-dd hh:mm.
Note
Applicable to BW, TFT and IFACE devices
5.2.13
System Data Management Functions
5.2.13.1 ClearKeeperData
VARIANT_BOOL ClearKeeperData(LONG dwMachineNumber)
To clear all data on the machine.
Parameters
Parameter description:
name
type param direction
dwMachineNumber LONG
description of param
[in]
Machine ID
136
Returns
Value description:
name type
True
description of value
BOOL Function execution success
False BOOL Function execution failure
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
5.2.13.2 ClearData
VARIANT_BOOL ClearData(LONG dwMachineNumber, LONG DataFlag)
To clear the records specified by DataFlag on the machine.
Parameters
Parameter description:
name
type param direction
dwMachineNumber LONG
DataFlag
LONG
description of param
[in]
Machine ID
[in]
This parameter specifies the
type of records to be cleared.
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
The DataFlag parameter specifies the type of records to be cleared. The value range is 1-5. The
meanings are as follows:
137
1 Attendance records
2 Fingerprint template data
3 None
4 Operation records
5 User information
If the value of this parameter is 5, all users on the machine will be deleted. Note: All fingerprint
templates will also be deleted.
Note
Applicable to BW, TFT and IFACE devices
5.2.13.3 GetDataFile
VARIANT_BOOL GetDataFile(LONG dwMachineNumber, LONG DataFlag, BSTR FileName)
To obtain a specified data file from the machine.
Parameters
Parameter description:
name
type param direction
dwMachineNumber LONG
description of param
[in]
Machine ID
DataFlag
LONG
[in]
Type of the data file to be
obtained
FileName
BSTR
[in]
Name of the data file that
is stored
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
The DataFlag parameter specifies the type of records to be cleared. The values are described as
follows:
1 Attendance records
138
2 Fingerprint template data
3 None
4 Operation records
5 User information
6 Short message data file
7 Data file of short messages and user relationships
8 Extended user information data file
9 Work code information data file
Note
Applicable to BW, TFT and IFACE devices
5.2.13.4 SendFile
VARIANT_BOOL SendFile(LONG dwMachineNumber, BSTR FileName)
To send a file to the machine, usually to the directory /mnt/mtdblock/.
Parameters
Parameter description:
name
type param direction
dwMachineNumber LONG
FileName
BSTR
description of param
[in]
Machine ID
[in]
Name of the file to be sent
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
If the color-screen machine transfers user pictures or advertisement pictures, name the pictures
properly and then the pictures will be automatically saved to the corresponding directory.
Name format of advertisement pictures: ad_Number.jpg. The value of number ranges from 1 to
20. For example, ad_4.jpg.
Name format of user pictures: User ID.jpg. For example, 1.jpg.
Note
Applicable to BW, TFT and IFACE devices
139
5.2.13.5 ReadFile
VARIANT_BOOL ReadFile(LONG dwMachineNumber, BSTR FileName, BSTR FilePath)
To read a specified file from the machine, usually under the directory /mnt/mtdblock/.
Parameters
Parameter description:
name
type param direction
dwMachineNumber LONG
description of param
[in]
Machine ID
FileName
BSTR
[in]
Name of the file to be read
FilePath
BSTR
[in]
Path for saving the file
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to BW
5.2.13.6 RefreshData
VARIANT_BOOL RefreshData(LONG dwMachineNumber)
To refresh the data on the machine. This function is typically invoked after user information or a
fingerprint is uploaded, so that the modification takes effect immediately.
Parameters
Parameter description:
name
type param direction
dwMachineNumber LONG
description of param
[in]
Machine ID
Returns
140
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
5.2.14
User Photo & Attendance Photo
5.2.14.1 UploadUserPhoto
VARIANT_BOOL UploadUserPhoto(LONG dwMachineNumber, BSTR FileName)
To upload a user picture to the machine.
Parameters
Parameter description:
name
type param direction
dwMachineNumber LONG
FileName
BSTR
description of param
[in]
Machine ID
[in]
User picture name and the
absolute path where the
picture resides
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
1. The FileName parameter specifies the absolute path where the user picture to be uploaded
141
resides, for example, C:\Users\HP\Desktop\11.jpg. The user picture is named in the format of
User ID.jpg.
2. This function can also be implemented by using the SendFile function.
3. You can invoke this function to upload multiple user pictures by traversing through all file
names under a specified directory.
Note
This interface is applicable to the new architecture firmware.
5.2.14.2 DownloadUserPhoto
VARIANT_BOOL DownloadUserPhoto(LONG dwMachineNumber, BSTR FileName,
BSTR FilePath)
To download a user picture from the machine to the software.
Parameters
Parameter description:
name
type param direction
dwMachineNumber LONG
description of param
[in]
Machine ID
FileName
BSTR
[in]
Name of the user picture, with the
file name extension .jpg
FilePath
BSTR
[in]
Absolute path where the downloaded
user picture is to be saved
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
1. The FileName parameter specifies the name of the user picture to be downloaded. The name
format is User ID.jpg, for example, 11.jag. The downloaded picture will be saved in JPG format
to the specified path.
2. The FilePath parameter specifies the absolute path where the downloaded picture is to be saved,
for example, C:\Users\HP\Desktop\.
142
Note
This interface is applicable to the new architecture firmware.
5.2.14.3 DeleteUserPhoto
VARIANT_BOOL DeleteUserPhoto(LONG dwMachineNumber, BSTR FileName)
To delete a single user picture or all user pictures on the machine.
Parameters
Parameter description:
name
type param direction
dwMachineNumber LONG
FileName
BSTR
description of param
[in]
Machine ID
[in]
Name of the user picture
to be deleted
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
1. The FileName parameter is used to set to delete one or all user pictures. To delete a single user
picture, specify the name of the picture, which is named in the format of User ID.jpg, for
example, 11.jpg. To delete all user pictures at a time, set this parameter to ALL, which is
case-sensitive.
2. The FilePath parameter specifies the absolute path where the downloaded picture is to be saved,
for example, C:\Users\HP\Desktop\.
Note
This interface is applicable to the new architecture firmware.
5.2.14.4 GetAllUserPhoto
VARIANT_BOOL GetAllUserPhoto(LONG dwMachineNumber, BSTR dlDir)
To download all user pictures from the machine to the software.
Parameters
143
Parameter description:
name
type param direction
dwMachineNumber LONG
dlDir
BSTR
description of param
[in]
Machine ID
[in]
Absolute path where the
downloaded user pictures
are to be saved
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
1. The dlDir parameter specifies the absolute path where the downloaded pictures are to be saved,
for example, C:\Users\HP\Desktop\.
2. All user pictures downloaded from the machine will be automatically saved in JPG format to
the specified path one by one.
Note
This interface is applicable to the new architecture firmware.
5.2.14.5 GetPhotoNamesByTime
VARIANT_BOOL GetPhotoNamesByTime(LONG dwMachineNumber, LONG iFlag,
BSTR sTime, BSTR eTime, BSTR* AllPhotoName)
To download attendance pictures from the machine.
Parameters
Parameter description:
name
type param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
iFlag
LONG
[in]
Flag bit
144
sTime
BSTR
[in]
Start time
eTime
BSTR
[in]
End time
AllPhotoName
BSTR*
[out]
Names of attendance
pictures
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
1. If the value of iFlag is 0, all attendance pictures on the machine will be downloaded. If the
value is 1, attendance pictures between sTime and eTime will be downloaded.
2. sTime: specifies the start time, in the format of YYYY-MM-DD hh:mm:ss.
3. eTime: specifies the end time, in the format of YYYY-MM-DD hh:mm:ss.
4. AllPhotoName: specifies the names of attendance pictures, in the format of verification success
pictures (separated with \t)+\n+verification failure pictures (separated with \t).
Note
Applicable to TFT
5.2.14.6 GetPhotoByName
VARIANT_BOOL GetPhotoByName(LONG dwMachineNumber, BSTR PhotoName, BYTE*
PhotoData, LONG* PhotoLength)
To download an attendance picture from the machine based on the picture name.
Parameters
Parameter description:
name
type param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
PhotoName
BSTR
[in]
Picture name
145
PhotoData
BYTE*
[out]
Picture data in binary
format
PhotoLength
LONG*
[out]
Picture size
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to TFT
5.2.14.7 GetPhotoCount.
VARIANT_BOOL GetPhotoCount(LONG dwMachineNumber, LONG* Count, LONG iFlag)
To query the number of attendance pictures on the machine.
Parameters
Parameter description:
name
type param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
Count
LONG*
[in]
Picture quantity
iFlag
LONG
[in]
Flag bit
Returns
Value description:
name type
True
BOOL
description of value
Function execution success
146
False BOOL
Function execution failure
See also
Attention
If the value of iFlag is 0, the total number of attendance pictures is returned. If the value is 1, the
number of pictures that pass verification is returned. If the value is 2, the number of pictures that
fail verification is returned.
Note
Applicable to TFT
5.2.14.8 ClearPhotoByTime
VARIANT_BOOL ClearPhotoByTime(LONG dwMachineNumber, LONG iFlag, BSTR sTime,
BSTR eTime)
To clear attendance pictures on the machine according to specified conditions.
Parameters
Parameter description:
name
type param direction
dwMachineNumber LONG
description of param
[in]
Machine ID
iFlag
LONG
[in]
Flag bit
sTime
BSTR
[in]
Start time
eTime
BSTR
[in]
End time
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
1. If the value of iFlag is 0, all attendance pictures on the machine will be downloaded. If the
value is 1, attendance pictures between sTime and eTime will be downloaded.
2. sTime: specifies the start time, in the format of YYYY-MM-DD hh:mm:ss.
147
3. eTime: specifies the end time, in the format of YYYY-MM-DD hh:mm:ss.
Note
Applicable to TFT
5.2.15
Bell Functions
5.2.15.1 GetBellSchDataEx
VARIANT_BOOL GetBellSchDataEx(LONG dwMachineNumber, LONG weekDay,
LONG Index, LONG* Enable, LONG* hour, LONG* min, LONG* voice, LONG* way,
LONG* InerBellDelay, LONG* ExtBellDelay)
To query bell settings based on the specified weekday and bell index.
Parameters
Parameter description:
name
type param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
weekDay
LONG
[in]
Weekday
Index
LONG
[in]
Bell index
Enable
LONG*
[out]
Whether to enable the bell
hour
LONG*
[out]
Hour
min
LONG*
[out]
Minute
voice
LONG*
[out]
Ringtone
way
LONG*
[out]
Ringing mode
InerBellDelay
LONG*
[out]
Internal ringing duration
ExtBellDelay
LONG*
[out]
External ringing duration
Returns
Value description:
name type
True
description of value
BOOL Function execution success
148
False BOOL Function execution failure
See also
NMS_GetBellSchData
Attention
1. weekDay: specifies the weekday. The value 0 indicates Monday, 1 Tuesday, 2 Wednesday, 3
Thursday, 4 Friday, 5 Saturday, and 6 Sunday.
2. Index: specifies the bell index. The value range is 1-65535.
3. Enable: specifies whether to enable the bell. The value 0 indicates disabling the bell and 1
indicates enabling the bell.
4. voice: specifies the ringtone. The value ranges from 1 to 10, representing bell01.wav to
bell10.wav respectively.
5. way: specifies the ringing mode. The value 0 indicates internal ringing, 1 external ringing, and
2 internal and external ringing.
6. InerBellDelay: specifies the internal ringing duration. The value ranges from 1 to 999, in
seconds.
7. ExtBellDelay: specifies the external ringing duration. The value ranges from 1 to 999, in
seconds.
Note
This interface is applicable to the new architecture firmware.
5.2.15.2 SetBellSchDataEx
VARIANT_BOOL SetBellSchDataEx(LONG dwMachineNumber, LONG weekDay, LONG Index,
LONG Enable, LONG hour, LONG min, LONG voice, LONG way, LONG InerBellDelay, LONG
ExtBellDelay)
To set bell information.
Parameters
Parameter description:
name
type param direction
dwMachineNumber LONG
description of param
[in]
Machine ID
weekDay
LONG
[in]
Weekday
Index
LONG
[in]
Bell index
Enable
LONG
[in]
Whether to enable the bell
hour
LONG
[in]
Hour
149
min
LONG
[in]
Minute
voice
LONG
[in]
Ringtone
way
LONG
[in]
Ringing mode
InerBellDelay
LONG
[in]
Internal ringing duration
ExtBellDelay
LONG
[in]
External ringing duration
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
1. weekDay: specifies the weekday. At most 7 days in a whole week can be set. Specify the
weekday by using the least significant 7 bits of a byte. You can set multiple weekdays.
The first bit indicates Monday (0x00000001), the second bit Tuesday (0x00000002), third bit
Wednesday (0x00000004), fourth bit Thursday (0x00000008), fifth bit Friday (0x00000010),
sixth bit Saturday (0x00000020), and seventh bit Sunday (0x00000040).
To set multiple days, add the corresponding values. For example, to set Monday and Thursday,
add 1 and 8, making 9. To set Tuesday, Friday and Saturday, add 2, 16 and 32, making 50.
2. Index: specifies the bell index. The value range is 1-65535.
3. Enable: specifies whether to enable the bell. The value 0 indicates disabling the bell and 1
indicates enabling the bell.
4. voice: specifies the ringtone. The value ranges from 1 to 10, representing bell01.wav to
bell10.wav respectively.
5. way: specifies the ringing mode. The value 0 indicates internal ringing, 1 external ringing, and
2 internal and external ringing.
6. InerBellDelay: specifies the internal ringing duration. The value ranges from 1 to 999, in
seconds.
7. ExtBellDelay: specifies the external ringing duration. The value ranges from 1 to 999, in
seconds.
Note
This interface is applicable to the new architecture firmware.
150
5.2.15.3 GetDayBellSchCount
VARIANT_BOOL GetDayBellSchCount(LONG dwMachineNumber, LONG* DayBellCnt)
To query the number of bells that are set on the machine.
Parameters
Parameter description:
name
type param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
DayBellCnt
LONG*
[out]
Bell quantity
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
This interface is applicable to the new architecture firmware.
5.2.15.4 GetMaxBellIDInBellSchData
VARIANT_BOOL GetMaxBellIDInBellSchData(LONG dwMachineNumber, LONG*
MaxBellID)
To obtain the maximum bell index among all bells.
Parameters
Parameter description:
name
type param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
MaxBellID
LONG*
[out]
Weekday
151
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
NMS_GetMaxBellIDInBellSchData
Attention
Note
This interface is applicable to the new architecture firmware.
5.2.15.5 ReadAllBellSchData
VARIANT_BOOL ReadAllBellSchData(LONG dwMachineNumber)
To read the information about all bells to the SDK memory.
Parameters
Parameter description:
name
type param direction
dwMachineNumber LONG
description of param
[in]
Machine ID
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
This function needs to be used together with GetEachBellInfo to obtain bell information.
Note
This interface is applicable to the new architecture firmware.
152
5.2.15.6 GetEachBellInfo
VARIANT_BOOL GetEachBellInfo(LONG dwMachineNumber, LONG* weekDay,
LONG* Index, LONG* Enable, LONG* hour, LONG* min, LONG* voice, LONG* way, LONG*
InerBellDelay, LONG* ExtBellDelay)
To read bell information records from the SDK memory one by one.
Parameters
Parameter description:
name
type param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
weekDay
LONG*
[out]
Weekday
Index
LONG*
[out]
Bell index
Enable
LONG*
[out]
Whether to enable the bell
hour
LONG*
[out]
Hour
min
LONG*
[out]
Minute
voice
LONG*
[out]
Ringtone
way
LONG*
[out]
Ringing mode
InerBellDelay
LONG*
[out]
Internal ringing duration
ExtBellDelay
LONG*
[out]
External ringing duration
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
1. This function needs to be used together with ReadAllBellSchData, which is used to read all
153
bell information to the memory.
2. weekDay: specifies the weekday. At most 7 days in a whole week can be set. Specify the
weekday by using the least significant 7 bits of a byte. You can set multiple weekdays.
The first bit indicates Monday (0x00000001), the second bit Tuesday (0x00000002), third bit
Wednesday (0x00000004), fourth bit Thursday (0x00000008), fifth bit Friday (0x00000010),
sixth bit Saturday (0x00000020), and seventh bit Sunday (0x00000040).
You can learn the weekday settings by checking whether the corresponding bit is set. For
example, if the returned value is 50, which is the sum of 0x00000002, 0x00000010 and
0x00000020, the bell is set to ring on Tuesday, Friday and Saturday.
3. Index: specifies the bell index. The value range is 1-65535.
4. Enable: specifies whether to enable the bell. The value 0 indicates disabling the bell and 1
indicates enabling the bell.
5. voice: specifies the ringtone. The value ranges from 1 to 10, representing bell01.wav to
bell10.wav respectively.
6. way: specifies the ringing mode. The value 0 indicates internal ringing, 1 external ringing, and
2 internal and external ringing.
7. InerBellDelay: specifies the internal ringing duration. The value ranges from 1 to 999, in
seconds.
8. ExtBellDelay: specifies the external ringing duration. The value ranges from 1 to 999, in
seconds.
Note
This interface is applicable to the new architecture firmware.
5.2.16
UserValidDate Functions
5.2.16.1 SetUserValidDate
VARIANT_BOOL SetUserValidDate(LONG dwMachineNumber, BSTR UserID, LONG Expires,
LONG ValidCount, BSTR StartDate, BSTR EndDate)
To set the validity period of a user account.
Parameters
Parameter description:
name
type param direction
dwMachineNumber LONG
description of param
[in]
Machine ID
UserID
BSTR
[in]
User ID
Expires
LONG
[in]
Validity period type
154
ValidCount
StartDate
EndDate
LONG
BSTR
BSTR
[in]
Number of valid usage times
[in]
Start time of the validity
period, in the format of
YYYY-MM-DD hh:mm:ss
[in]
End time of the validity
period, in the format of
YYYY-MM-DD hh:mm:ss
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
1. UserID: specifies the ID. The user ID is a string of English letters.
2. Expires: specifies the validity period type. The value ranges from 0 to 3. The value 0 indicates
not limiting the the validity period of the user account, 1 indicates limiting the validity period by
setting the start time and end time, 2 indicates limiting the validity period by setting the number
of usage times, and 3 indicates limiting the validity period by setting the start time, end time, and
number of usage times.
3. ValidCount: specifies the number of usage times of the user account. The value is larger than
or equal to 0.
4. StartDate: specifies the start time of the validity period. Only the YYYY-MM-DD part is kept
because time is accurate only to date on the firmware.
5. EndDate: specifies the end time of the validity period. Only the YYYY-MM-DD part is kept
because time is accurate only to date on the firmware.
Note
This interface is applicable to the new architecture firmware.
5.2.16.2 GetUserValidDate
VARIANT_BOOL GetUserValidDate(LONG dwMachineNumber, BSTR UserID,
LONG* Expires, LONG* ValidCount, BSTR* StartDate, BSTR* EndDate)
To query the validity period of a user account.
Parameters
155
Parameter description:
name
type param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
UserID
BSTR
[in]
User ID
Expires
LONG*
[out]
Validity period type
ValidCount
LONG*
[out]
Number of valid usage times
[out]
Start time of the validity
period, in the format of
YYYY-MM-DD hh:mm:ss
[out]
End time of the validity
period, in the format of
YYYY-MM-DD hh:mm:ss
StartDate
EndDate
BSTR*
BSTR*
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
1. UserID: specifies the ID. The user ID is a string of English letters.
2. Expires: specifies the validity period type. The value ranges from 0 to 3. The value 0 indicates
not limiting the the validity period of the user account, 1 indicates limiting the validity period by
setting the start time and end time, 2 indicates limiting the validity period by setting the number
of usage times, and 3 indicates limiting the validity period by setting the start time, end time, and
number of usage times.
3. ValidCount: specifies the number of usage times of the user account. The value is larger than
or equal to 0.
4. StartDate: specifies the start time of the validity period. Only the YYYY-MM-DD part is kept
because time is accurate only to date on the firmware.
5. EndDate: specifies the end time of the validity period. Only the YYYY-MM-DD part is kept
because time is accurate only to date on the firmware.
156
Note
This interface is applicable to the new architecture firmware.
5.2.17
Personalise Functions
5.2.17.1 UploadTheme
VARIANT_BOOL UploadTheme(LONG dwMachineNumber, BSTR FileName, BSTR
InDevName)
To upload a theme picture to the machine.
Parameters
Parameter description:
name
type param direction
dwMachineNumber LONG
description of param
[in]
Machine ID
FileName
BSTR
[in]
Save path + File name
InDevName
BSTR
[in]
File name in the device
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
The FileName parameter specifies the file name and save path of the theme picture to be
uploaded.
Note
This interface is applicable to the new architecture firmware.
5.2.17.2 UploadPicture
VARIANT_BOOL UploadPicture(LONG dwMachineNumber, BSTR FileName,
BSTR InDevName)
To upload a background picture to the machine.
157
Parameters
Parameter description:
name
type param direction
dwMachineNumber LONG
description of param
[in]
Machine ID
FileName
BSTR
[in]
Save path + File name
InDevName
BSTR
[in]
File name in the device
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
The FileName parameter specifies the file name and save path of the background picture to be
uploaded.
Note
This interface is applicable to the new architecture firmware.
5.2.17.3 DownloadPicture
VARIANT_BOOL DownloadPicture(LONG dwMachineNumber, BSTR FileName, BSTR
FilePath)
To download the background picture from the machine.
Parameters
Parameter description:
name
type param direction
dwMachineNumber LONG
FileName
BSTR
description of param
[in]
Machine ID
[in]
Name of the picture file
158
FilePath
BSTR
Path where the downloaded
picture is to be saved
[in]
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
This interface is applicable to the new architecture firmware.
5.2.18
APP Info Functions
5.2.18.1 GetAllAppFun
VARIANT_BOOL GetAllAppFun(LONG dwMachineNumber, BSTR* AppName, BSTR*
FunofAppName)
To query all App names, all App and corresponding Fun names.
Parameters
Parameter description:
name
type
param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
[out]
App name list.The data is in .txt
format and format name is [App
name]. Records are separated with
\r\n;
[out]
App and App functions lsit.The
data is in .txt format and format
name is [Fun name, Function name].
Records are separated with \r\n;
AppName
FunofAppName
BSTR
BSTR
Returns
159
Value description:
name
type
description of value
True
BOOL
Function execution success
False
BOOL
Function execution failure
See also
Attention
Note
It is applicable to the new architecture machine
5.2.18.2 GetAllRole
VARIANT_BOOL GetAllRole(LONG dwMachineNumber, BSTR* RoleName)
To query all role names and the corresponding permission names.
Parameters
Parameter description:
name
type
param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
[out]
To query all role names and the
corresponding permission names.
The data is in .txt format and
format name is [Role name,
Permission name]. Records are
separated with \r\n;
RoleName
BSTR
Value description:
name
type
description of value
True
BOOL
Function execution success
False
BOOL
Function execution failure
See also
Attention
Note
160
It is applicable to the new architecture machine
5.2.18.3 GetAppOfRole
VARIANT_BOOL GetAppOfRole(LONG dwMachineNumber, LONG Permission, BSTR*
AppName)
To query all App names with specified role permission.
Parameters
Parameter description:
name
type
param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
Permission
LONG
[in]
Permisssion of specified role
[out]
AppName with the specified role
permission will be returned. The
data is in .txt format and format
name is [App name]. Records are
separated with \r\n;
AppName
BSTR
Returns
Value description:
name
type
description of value
True
BOOL
Function execution success
False
BOOL
Function execution failure
See also
Attention
Note
It is applicable to the new architecture machine
5.2.18.4 GetFunOfRole
VARIANT_BOOL GetFunOfRole(LONG dwMachineNumber, LONG Permission, BSTR*
FunName)
To query all function names with the specified role permission.
161
Parameters
Parameter description:
name
type
param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
Permission
LONG
[in]
Permisssion of specified role
[out]
FunName with the specified role
permission will be returned. The
data is in .txt format and format
name is [Function name]. Records
are separated with \r\n;
FunName
BSTR
Returns
Value description:
name
type
description of value
True
BOOL
Function execution success
False
BOOL
Function execution failure
See also
Attention
Note
It is applicable to the new architecture machine
5.2.18.5 SetPermOfAppFun
VARIANT_BOOL SetPermOfAppFun(LONG dwMachineNumber, LONG Permission, BSTR
AppName, BSTR FunName)
To set the corresponding permission of function and App meanwhile.
Parameters
Parameter description:
name
type
param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
Permission
LONG
[in]
Permission value to be set
162
AppName
BSTR
[in]
App name
FunName
BSTR
[in]
Fun name
Returns
Value description:
name
type
description of value
True
BOOL
Function execution success
False
BOOL
Function execution failure
See also
Attention
Function of FunName must be included in the functions of AppName
Note
It is applicable to the new architecture machine
5.2.18.6 DeletePermOfAppFun
VARIANT_BOOL DeletePermOfAppFun(LONG dwMachineNumber, LONG Permission, BSTR
AppName, BSTR FunName)
To delete the corresponding permission of function and App meanwhile.
Parameters
Parameter description:
name
type
param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
Permission
LONG
[in]
Permission value to be deleted
AppName
BSTR
[in]
App name
FunName
BSTR
[in]
Fun name
Returns
Value description:
name
type
description of value
163
True
BOOL
Function execution success
False
BOOL
Function execution failure
See also
Attention
Function of FunName must be included in the functions of AppName
Note
It is applicable to the new architecture machine
5.2.18.7 IsUserDefRoleEnable
VARIANT_BOOL IsUserDefRoleEnable(LONG dwMachineNumber, LONG Permission,
VARIANT_BOOL* Enable)
To judge whether the user defined role is enabled.
Parameters
Parameter description:
name
type
param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
Permission
LONG
[in]
Permission value to be deleted
[out]
Whether the user defined role
is enabled: 1 means enable and
0 means disable
Enable
BOOL*
Returns
Value description:
name
type
description of value
True
BOOL
Function execution success
False
BOOL
Function execution failure
See also
Attention
Note
It is applicable to the new architecture machine
164
5.2.19
Template Integration Functions
5.2.19.1 SSR_SetDeviceData
VARIANT_BOOL SSR_SetDeviceData(LONG dwMachineNumber, BSTR TableName, BSTR
Datas, BSTR Options)
This function is applicable to an attendance machine on which the new firmware supports the
PULL protocol. This function is used to set data, including the time segment, user information,
and holiday settings. The data can be one or more records. If the primary key of an inserted
record already exists, the original record will be overwritten.
Parameters
Parameter description:
name
type
param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
[in]
Data table name. For details about
the available tables, see attachment
1 PULL Data Dictionary for the New
Firmware.
TableName
BSTR
Datas
BSTR
[in]
Data records. The data is in .txt
format. Records are separated with
\r\n, and fields with values are
separated with \t.
Options
BSTR
[in]
It is left blank by default and for
extension.
Returns
Value description:
name
type
description of value
True
BOOL
Function execution success
False
BOOL
Function execution failure
See also
Attention
Note
165
This interface is applicable to the new architecture firmware.
5.2.19.2 SSR_GetDeviceData
VARIANT_BOOL SSR_GetDeviceData(LONG dwMachineNumber, BSTR* Buffer, LONG
BufferSize, BSTR TableName, BSTR FiledNames, BSTR Filter, BSTR Options)
This function is applicable to an attendance machine on which the new firmware supports the
PULL protocol. This function is used to read data from the machine, including the punch records,
time segments, user information, and holiday settings. The data can be one or more records.
Parameters
Parameter description:
name
type
param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
Buffer
BSR*
[out]
Buffer for storing returned data. The
returned data is in .txt format and
may contain multiple records, which
are separated with \r\n.
BufferSize
LONG
[in]
Size of the buffer for storing
returned data
[in]
Data table name. For details about
the available tables, see attachment
1 PULL Data Dictionary for the New
Firmware.
[in]
Field name list. The fields are
separated with \t. * indicates all
fields. The field names are on the
first line in the returned data.
TableName
FiledNames
BSTR
BSTR
Filter
BSTR
[in]
Filter criteria for reading data. If
the data is a character string in the
format of "field name operator
value", multiple filter criteria
separated with a comma (,) are
supported. The details are as
follows:
Options
BSTR
[in]
Options
Returns
166
Value description:
name
type
description of value
True
BOOL
Function execution success
False
BOOL
Function execution failure
See also
Attention
Note
This interface is applicable to the new architecture firmware.
5.2.19.3 SSR_GetDeviceDataCount
VARIANT_BOOL SSR_GetDeviceDataCount(BSTR TableName, BSTR Filter, BSTR Options)
Query the number of The unification of multiple Biometric Templates within the device.
Parameters
Parameters are shown below:
name
type param direction description of param
TableName BSTR
[in]
Name of Table
Filter
BSTR
[in]
Filter condition
Options
BSTR
[in]
parameter
Returns
returned value specification:
name type
True
BOOL
False BOOL
description of value
Success
Fault
See also
Attention
Note
This interface is applicable to BW,TFT devices,For The unification of multiple Biometric
Template Tablestructure, see the SSR_SetDeviceData interface Attention
167
5.2.19.4 SSR_DeleteDeviceData
VARIANT_BOOL SSR_DeleteDeviceData(LONG dwMachineNumber, BSTR TableName, BSTR
Datas, BSTR Options)
Delete The unification of multiple Biometric Templates within the device.
Parameters
Parameters are shown below:
name
type param direction description of param
TableName BSTR
[in]
Name of Table
Datas
BSTR
[in]
Filter condition
Options
BSTR
[in]
parameter
Returns
returned value specification:
name type
True
description of value
BOOL
Success
False BOOL
Fault
See also
Attention
Note
This interface is applicable to BW,TFT devices,For The unification of multiple Biometric
Template Tablestructure, see the SSR_SetDeviceData interface Attention
5.2.19.5 Variable description : BiometricType
BiometricType.
Parameters
BiometricType Get the supported biometric type by retrieving the parameter and return 8-bit
numeric string. Each represents a type of biometric type. (0 not support ; 1
support;e.g.:BiometricType=01100000 ,device support FP and Face)
Character
index
0
1
2
3
4
5
168
6
7
8
Related Type
General
FP
Face
Voice
Iris
Retina
Palmprint
FingerVein
Palmvein
See also
Attention
Note
Applicable to interface of unification of multiple Biometric Template
5.2.19.6 Variable description : BiometricVersion
BiometricVersion.
Parameters
BiometricVersion Get the version of the supported biometric type Get the version of the
supported biometric type of the device by retrieving the parameter and return the version of the
supported biometric type seperated by ":" (e.g.:BiometricVersion=0:10.0:7.0:::::device support
FP10.0 and Face7.0)
Character
index
0
1
2
3
4
5
6
7
8
Related Type
General
FP
Face
Voice
Iris
Retina
Palmprint
FingerVein
Palmvein
See also
Attention
TableName
Note
Applicable to interface of unification of multiple Biometric Template
5.2.19.7 Variable description : BiometricMaxCount
BiometricMaxCount.
Parameters
BiometricMaxCount Get the supported biometric type data capacity by retrieving the parameter
and return the supported biometric type data capacity seperated by ":"
(e.g.:BiometricMaxCount=0:3000:1000:::::,device support 3000 FP and 1000 Face templates)
Character
index
0
1
2
3
4
5
6
7
8
Related Type
General
FP
Face
Voice
Iris
Retina
Palmprint
FingerVein
Palmvein
The new device is directly returned by the firmware, and the old firmware is SDK
compatible.(supported)
169
See also
Attention
TableName
Note
Applicable to interface of unification of multiple Biometric Template
5.2.19.8 Variable description : BiometricUsedCount
BiometricUsedCount.
Parameters
BiometricUsedCount Get the number of supported biometric type data by retrieving the
padameter and return the number of supported biometric type data seperated by ":"
(e.g.:BiometricUsedCount=0:100:10:::::,indicate there are 100 FP templates, 10 faces)
Character
index
0
1
2
3
4
5
6
7
8
Related Type
General
FP
Face
Voice
Iris
Retina
Palmprint
FingerVein
Palmvein
See also
Attention
TableName
Note
Applicable to interface of unification of multiple Biometric Template
5.3 Access Control Functions(Time Slot, Group, Open Door
Combination)
5.3.1
GetUserGroup
VARIANT_BOOL GetUserGroup(LONG dwMachineNumber, LONG dwEnrollNumber, LONG*
UserGrp)
To obtain the ID of the group to which a specified user belongs.
Parameters
Parameter description:
name
type param direction
170
description of
param
dwMachineNumber
LONG
[in]
Machine ID
dwEnrollNumber
LONG
[in]
User ID
UserGrp
LONG*
[out]
Returned group ID
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
The value of UserGrp is the ID of the group to which the user specified by dwEnrollNumber
belongs. The value range is 1-5.
Note
Applicable to BW, TFT, and IFACE devices
5.3.2
SetUserGroup
VARIANT_BOOL SetUserGroup(LONG dwMachineNumber, LONG dwEnrollNumber, LONG
UserGrp)
To set the group to which a specified user belongs.
Parameters
Parameter description:
description of
name
type param direction
param
dwMachineNumber LONG
[in]
Machine ID
171
dwEnrollNumber
LONG
[in]
User ID
UserGrpl
LONG
[in]
Group ID
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
The value of UserGrp is the ID of the group to which the user specified by dwEnrollNumber
belongs. The value range is 1-5.
Note
Applicable to BW, TFT, and IFACE devices
5.3.3
GetTZInfo
VARIANT_BOOL GetTZInfo(LONG dwMachineNumber, LONG TZIndex, BSTR* TZ)
To obtain the information about a time segment with a specified index.
Parameters
Parameter description:
description of
name
type param direction
param
dwMachineNumber
LONG
[in]
Machine ID
TZIndex
LONG
[in]
Time segment index
[out]
The value is the
information about
the time segment with
the index specified
by TZIndex.
TZ
BSTR*
Returns
172
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
The value of the TZ parameter is the information about the time segment with the index specified
by TZIndex. Every eight digits indicate a time segment in the format of hhmmhhmm. For
example, 10111223000023590000235900002359000023590000235900002359 indicates the time
segment from 10:11 to 12:23 on Sunday and the whole day from Monday to Saturday.
Note
Applicable to BW, TFT, and IFACE devices
5.3.4
SetTZInfo
VARIANT_BOOL SetTZInfo(LONG dwMachineNumber, LONG TZIndex, BSTR TZ)
To set the information about a time segment with a specified index.
Parameters
Parameter description:
description of
name
type param direction
param
dwMachineNumber LONG
[in]
Machine ID
TZIndex
LONG
[in]
Time segment index
TZ
BSTR
[in]
Time segment
information to be set
Returns
Value description:
name type
True
BOOL
description of value
Function execution success
173
False BOOL
Function execution failure
See also
Attention
The TZ parameter specifies the time segment information to be set. Every eight digits indicate a
time segment in the format of hhmmhhmm.For example, 10111223000023590000235900002359
000023590000235900002359 indicates the time segment from 10:11 to 12:23 on Sunday and the
whole day from Monday to Saturday.
Note
Applicable to BW, TFT, and IFACE devices
5.3.5
GetUnlockGroups
VARIANT_BOOL GetUnlockGroups(LONG dwMachineNumber, BSTR* Grps)
To obtain unlock combinations of the machine.
Parameters
Parameter description:
description of
name
type param direction
param
dwMachineNumber
Grps
LONG
BSTR*
[in]
Machine ID
[out]
Current unlock
combination of the
machine
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
174
The value of the Grps parameter is an unlock combination. There are totally 10 unlock
combinations, separated with a colon (:). For example, 12:23:14:15 represents four valid
combinations, which are combination 1 (12 represents groups 1 and 2), combination 2 (23
represents groups 2 and 3), combination 3 (14 represents groups 1 and 4), and combination 4 (15
represents groups 1 and 5).
Note
Applicable to BW
5.3.6
SetUnlockGroups
VARIANT_BOOL SetUnlockGroups(LONG dwMachineNumber, BSTR Grps)
To set unlock combinations.
Parameters
Parameter description:
description of
name
type param direction
param
dwMachineNumber LONG
Grps
BSTR
[in]
Machine ID
[in]
Unlock combination
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Totally 10 unlock combinations need to be set, and separate these combinations with a colon (:).
For example, 12:23:14:15 represents four valid combinations, which are combination 1 (12
represents groups 1 and 2), combination 2 (23 represents groups 2 and 3), combination 3 (14
represents groups 1 and 4), and combination 4 (15 represents groups 1 and 5).
Note
Applicable to BW
175
5.3.7
SSR_SetUnLockGroup
VARIANT_BOOL SSR_SetUnLockGroup(LONG dwMachineNumber, LONG CombNo,
LONG Group1, LONG Group2, LONG Group3，LONG Group4，LONG Group5)
To set unlock combinations.
Parameters
Parameter description:
description of
name
type param direction
param
dwMachineNumber LONG
[in]
Machine ID
CombNo
LONG
[in]
Unlock combination ID
ranging from 1 to 10.
The machine supports
at most 10 unlock
combinations.
Group1
LONG
[in]
Unlock combination
group 1
Group2
LONG
[in]
Unlock combination
group 2
Group3
LONG
[in]
Unlock combination
group 3
Group4
LONG
[in]
Unlock combination
group 4
Group5
LONG
[in]
Unlock combination
group 5
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
176
See also
Attention
Group1, Group2, Group3, Group4 and Group5 are group IDs of an unlock combination. Each
unlock combination contains five group IDs. The group ID ranges from 1 to 99. For example,
SSR_SetUnLockGroup(1,1,2,23,14,0,56) indicates that the personnel of groups 2, 23, 14 and 56
need to verify together to open the door.
Note
Applicable to TFT and IFACE devices
5.3.8
SSR_GetUnLockGroup
VARIANT_BOOL SSR_GetUnLockGroup(LONG dwMachineNumber, LONG CombNo,
LONG* Group1, LONG* Group2, LONG* Group3, LONG* Group4, LONG* Group5)
To obtain unlock combination information based on the group ID.
Parameters
Parameter description:
name
type param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
CombNo
LONG
[in]
Unlock combination ID ranging from 1
to 10
Group1
LONG*
[out]
Unlock combination group 1
Group2
LONG*
[out]
Unlock combination group 2
Group3
LONG*
[out]
Unlock combination group 3
Group4
LONG*
[out]
Unlock combination group 4
Group5
LONG*
[out]
Unlock combination group 5
Returns
Value description:
name type
True
description of value
BOOL Function execution success
177
False BOOL Function execution failure
See also
Attention
The values of Group1, Group2, Group3, Group4, and Group5 are group IDs of the specified
unlock combination. The group IDs are returned. Each unlock combination contains a maximum
of five groups. The group ID ranges from 1 to 99.
Note
Applicable to TFT and IFACE devices
5.3.9
GetGroupTZs
VARIANT_BOOL GetGroupTZs(LONG dwMachineNumber, LONG GroupIndex, LONG* TZs)
To obtain the time segments of a specified group. This function differs from GetGroupTZStr in
the format of the returned values.
Parameters
Parameter description:
description of
name
type param direction
param
dwMachineNumber
LONG
[in]
Machine ID
GroupIndex
LONG
[in]
Group index, ranging
from 1 to 5
TZs
LONG*
[out]
Time segment index
Returns
Value description:
name
type
description of value
True
BOOL
Function execution success
False
BOOL
Function execution failure
See also
Attention
The TZs parameter is a LONG pointer. Its value is the indexes of the three time segments used by
178
the group specified by GroupIndex, indicated by TZs[0], TZs[1] and TZs[2] respectively.
Note
Applicable to BW
5.3.10
SetGroupTZs
VARIANT_BOOL SetGroupTZs(LONG dwMachineNumber, LONG GroupIndex, LONG* TZs)
To set the three time segments of a specified group. This function differs from SetGroupTZStr in
the format of the specified values.
Parameters
Parameter description:
description of
name
type param direction
param
dwMachineNumber
LONG
[in]
Machine ID
GroupIndex
LONG
[in]
Group index, ranging
from 1 to 5
TZs
LONG*
[in]
Time segment index
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
The TZs parameter is a LONG pointer. The three time segments are specified by TZs[0], TZs[1],
and TZs[2] respectively.
Note
Applicable to BW
179
5.3.11
GetGroupTZStr
VARIANT_BOOL GetGroupTZStr(LONG dwMachineNumber, LONG GroupIndex,BSTR*
TZs)
To obtain the time segments of a specified group. This function differs from GetGroupTZs in the
format of the returned values.
Parameters
Parameter description:
description of
name
type param direction
param
dwMachineNumber
LONG
[in]
Machine ID
GroupIndex
LONG
[in]
Group index, ranging
from 1 to 5
TZs
BSTR*
[out]
Time segment index
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
The value of TZs is the indexes of the time segments of the group specified by GroupIndex. Each
group contains three time segments separated with a colon (:). For example, if the returned value
is 1:23:13, the indexes of the three time segments are 1, 23 and 13 respectively.
Note
Applicable to BW
5.3.12
SetGroupTZStr
VARIANT_BOOL SetGroupTZStr(LONG dwMachineNumber, LONG GroupIndex, BSTR TZs)
To set the time segments of a specified group. This function differs from SetGroupTZs in the
180
format of the specified values.
Parameters
Parameter description:
description of
name
type param direction
param
dwMachineNumber LONG
[in]
Machine ID
GroupIndex
LONG
[in]
Group index, ranging
from 1 to 5
TZs
BSTR
[in]
Time segment index
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
The TZs parameter specifies the indexes of the time segments of the group described by
GroupIndex. Each group contains three time segments separated with a colon (:). For example, if
the value is set to 1:23:13, the indexes of the three time segments are 1, 23 and 13 respectively.
Note
Applicable to BW
5.3.13
SSR_SetGroupTZ
VARIANT_BOOL SSR_SetGroupTZ(LONG dwMachineNumber, LONG GroupNo, LONG Tz1,
LONG Tz2, LONG Tz3, LONG ValidHoliday, LONG VerifyStyle)
To set the time segments of a group.
Parameters
Parameter description:
181
description of
name
type param direction
param
dwMachineNumber LONG
[in]
Machine ID
GroupNo
LONG
[in]
Group ID, ranging from
1 to 99
Tz1
LONG
[in]
Time segment 1
Tz2
LONG
[in]
Time segment 2
Tz3
LONG
[in]
Time segment 3
ValidHoliday
LONG
[in]
Whether the time
segments are valid on
holidays
VerifyStyle
LONG
[in]
Group verification
mode
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
The VerifyStyle parameter specifies the group verification mode. 0(FP/PW/RF), 1(FP), 2(PIN),
3(PW), 4(RF), 5(FP&RF), 6(FP/PW), 7(FP/RF), 8(PW/RF), 9(PIN&FP), 10(FP&PW),
11(PW&RF), 12(FP&PW&RF), 13(PIN&FP&PW), 14(FP&RF/PIN).
Note
Applicable to TFT and IFACE devices
5.3.14
SSR_GetGroupTZ
VARIANT_BOOL SSR_GetGroupTZ(LONG dwMachineNumber, LONG GroupNo, LONG Tz1,
LONG Tz2, LONG Tz3, LONG ValidHoliday, LONG VerifyStyle)
182
To obtain the time segments of a group.
Parameters
Parameter description:
param
name
type
description of param
direction
dwMachineNumber
LONG
[in]
Fingerprint machine ID
GroupNo
LONG
[in]
Group ID, ranging from 1 to 99
[out]
The indexes of the three time segments of
the specified group are returned. The index
ranges from 1 to 50.
[out]
The indexes of the three time segments of
the specified group are returned. The index
ranges from 1 to 50.
[out]
The indexes of the three time segments of
the specified group are returned. The index
ranges from 1 to 50.
Tz1
Tz2
Tz3
LONG*
LONG*
LONG*
ValidHoliday
LONG*
[out]
Whether the time segments are valid on
holidays. The value 1 indicates that the
time segments are valid on holidays and 0
indicates that the time segments are
invalid on holidays.
VerifyStyle
LONG*
[out]
Verification mode of the fingerprint
machine
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
183
Attention
The VerifyStyle parameter specifies the group verification mode. 0(FP/PW/RF), 1(FP), 2(PIN),
3(PW), 4(RF), 5(FP&RF), 6(FP/PW), 7(FP/RF), 8(PW/RF), 9(PIN&FP), 10(FP&PW),
11(PW&RF), 12(FP&PW&RF), 13(PIN&FP&PW), 14(FP&RF/PIN).
Note
Applicable to TFT and IFACE devices
5.3.15
GetUserTZs
VARIANT_BOOL GetUserTZs(LONG dwMachineNumber, LONG UserID, LONG TZs)
To obtain the time segments of a user. Each user has three time segments. This function differs
from GetUserTZStr in the format of the returned time segments.
Parameters
Parameter description:
description of
name
type param direction
param
dwMachineNumber
LONG
[in]
Machine ID
UserID
LONG
[in]
User ID
[out]
Time segments during
which the user can
open the door
TZs
LONG*
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
The TZs pointer has three values that store three time segment indexes, which can be read from
TZs[0], TZs[1] and TZs[2] respectively.
Note
184
Applicable to BW, TFT, and IFACE devices
5.3.16
SetUserTZs
VARIANT_BOOL SetUserTZs(LONG dwMachineNumber, LONG UserID, LONG* TZs)
To set the time segments of a user. At most three time segments can be set for a user. This
function differs from SetUserTZStr in the format of specified time segments.
Parameters
Parameter description:
description of
name
type param direction
param
dwMachineNumber
LONG
[in]
Machine ID
UserID
LONG
[in]
User ID
TZs
LONG*
[in]
Time segment index
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
The TZs parameter specifies the indexes of the time segments of the user described by UserID.
The three indexes can be specified by TZs[0], TZs[1] and TZs[2] respectively. When TZs[0] is 0,
the group setting takes effect. When it is 1, a user-defined setting takes effect.
Note
Applicable to BW, TFT, and IFACE devices
5.3.17
GetUserTZStr
VARIANT_BOOL GetUserTZStr(LONG dwMachineNumber, LONG UserID, BSTR* TZs)
To obtain the time segments of a user. This function differs from GetUserTZs in the format of
returned time segments.
185
Parameters
Parameter description:
description of
name
type param direction
param
dwMachineNumber
LONG
[in]
Machine ID
UserID
LONG
[in]
User ID
TZs
BSTR*
[out]
Unlock time segments
of the user
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
The TZs parameter specifies the unlock time segments of the user. The details are as follows:
Monochrome access control panel: X1:X2:X3. X1, X2 and X3 are indexes of user-defined time
segments. If X1 is 0, the group time segments are used. To query whether a user uses the group
time segments, invoke the UseGroupTimeZone function and check the returned value. If user A
uses user-defined time segments 1 and 2, the fingerprint machine will return 1:2:0. If user B uses
the group time segments, the fingerprint machine will return 0:0:0.
Color-screen access control panel: X1:X2:X3:X4. X4 specifies whether to use the group time
segments. The value 0 indicates using the group time segments and 1 indicates using user-defined
time segments. X1, X2 and X3 are indexes of used time segments. For example, if user A uses
user-defined time segments 1 and 2, the fingerprint machine will return 1:2:0:1. If user B uses the
group time segments defined as 1:1:1:0, the fingerprint machine will return 0:0:0:0.
Note
Applicable to BW, TFT and IFACE devices
5.3.18
SetUserTZStr
VARIANT_BOOL SetUserTZStr(LONG dwMachineNumber, LONG UserID, BSTR TZs)
186
To set the time segments of a user. The time segments are separated with a colon (:). This
function differs from SetUserTZs in the format of specified time segments.
Parameters
Parameter description:
description of
name
type param direction
param
dwMachineNumber LONG
[in]
Machine ID
UserID
LONG
[in]
User ID
TZs
BSTR
[in]
Unlock time segments
of the user
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
The TZs parameter specifies the unlock time segments of the user. The details are as follows:
Monochrome access control panel: X1:X2:X3. X1, X2 and X3 are indexes of user-defined time
segments. If X1 is 0, the group time segments are used. To query whether a user uses the group
time segments, invoke the UseGroupTimeZone function and check the returned value. If user A
uses user-defined time segments 1 and 2, the fingerprint machine will return 1:2:0. If user B uses
the group time segments, the fingerprint machine will return 0:0:0.Color-screen access control
panel: X1:X2:X3:X4. X4 specifies whether to use the group time segments. The value 0 indicates
using the group time segments and 1 indicates using user-defined time segments. X1, X2 and X3
are indexes of used time segments. For example, if user A uses user-defined time segments 1 and
2, the fingerprint machine will return 1:2:0:1. If user B uses the group time segments defined as
1:1:1:0, the fingerprint machine will return 0:0:0:0.
Note
Applicable to BW, TFT and IFACE devices
187
5.3.19
ACUnlock
VARIANT_BOOL ACUnlock(LONG dwMachineNumber, LONG Delay)
To enable the access control panel to output door opening level and close the door after Delay/10
seconds.
Parameters
Parameter description:
description of
name
type param direction
param
dwMachineNumber LONG
Delay
LONG
[in]
Machine ID
[in]
Delay in closing the
door
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
5.3.20
GetACFun
VARIANT_BOOL GetACFun(LONG* ACFun)
To check whether the machine has the access control function.
Parameters
Parameter description:
188
name
type param direction
ACFun LONG*
description of param
Flag of the access
control function
[out]
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
The ACFun parameter is an access control flag. The value 0 indicates that access control is
unavailable, 1 indicates simple access control, 2 indicates medium-level access control, 6
indicates advanced access control, and 14 indicates advanced access control+normal open.
Note
Applicable to BW, TFT and IFACE devices
5.3.21
GetDoorState
VARIANT_BOOL GetDoorState(LONG MachineNumber, LONG* State)
To query the current door status. The value 1 indicates that the door is opened and 0 indicates that
the door is closed.
Parameters
Parameter description:
description of
name
type param direction
param
MachineNumber
LONG
[in]
Machine ID
State
LONG*
[out]
Door status
Returns
Value description:
189
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
5.3.22
UseGroupTimeZone
VARIANT_BOOL UseGroupTimeZone()
To query whether a user uses the group time segments.
Parameters
none
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
This function must be used together with GetUserTZs or GetUserTZStr. Specifically, invoke the
GetUserTZs or GetUserTZStr function to obtain the time segment information about a user, and
then invoke UseGroupTimeZone to check whether the user uses the group time segments.
Note
Applicable to BW, TFT and IFACE devices
5.3.23
TurnOffAlarm
VARIANT_BOOL TurnOffAlarm(LONG dwMachineNumber)
To turn off alarms.
190
Parameters
Parameter description:
name
type param direction description of param
dwMachineNumber LONG
[in]
Machine ID
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
This interface is applicable to the new architecture firmware.
5.4 Device Management Functions
5.4.1
IsTFTMachine
VARIANT_BOOL IsTFTMachine(LONG dwMachineNumber)
To check whether the machine is a color-screen one.
Parameters
Parameter description:
name
type param direction
dwMachineNumber LONG
description of param
[in]
Machine ID
Returns
Value description:
name type
description of value
191
True
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
5.4.2
GetDeviceStatus
VARIANT_BOOL GetDeviceStatus(LONG dwMachineNumber, LONG dwStatus, LONG*
dwValue)
To query the data storage status on the machine, such as the number of administrators and
number of users.
Parameters
Parameter description:
description of
name
type param direction
param
dwMachineNumber
LONG
[in]
Machine ID
dwStatus
LONG
[in]
Data to be obtained
dwValue
LONG*
[out]
Content of the data
specified by
dwStatus
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
192
See also
Attention
The dwStatus parameter specifies the data to be obtained. The value range is 1-22. The values are
described as follows:
1 Number of administrators
2 Number of registered users
3 Number of fingerprint templates on the machine
4 Number of passwords
5 Number of operation records
6 Number of attendance records
7 Fingerprint template capacity
8 User capacity
9 Attendance record capacity
10 Remaining fingerprint template capacity
11 Remaining user capacity
12 Remaining attendance record capacity
21 Number of faces
22 Face capacity
0 Other conditions
Note
Applicable to BW, TFT, and IFACE devices
5.4.3
GetDeviceInfo
VARIANT_BOOL GetDeviceInfo(LONG dwMachineNumber, LONG dwInfo, LONG* dwValue)
To obtain machine information, such as the language and baud rate.
Parameters
Parameter description:
description of
name
type param direction
param
dwMachineNumber
LONG
[in]
Machine ID
dwInfo
LONG
[in]
Information type
[out]
Informatin of the
type specified by
dwInfo
dwValue
LONG*
Returns
193
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
dwInfo: specifies the type of information to be obtained. The value ranges from 1 to 68, and
cannot be 65. The values are described as follows:
1. Maximum number of administrators, which is fixed at 500.
2. Machine ID.
3. Language: If the value of dwValue is 0, the language is English. The value 1 indicates other
conditions. The value 2 indicates Traditional Chinese, and 3 indicates Thai.
4. Idle duration (in minutes): After the specified idle duration elapses, the machine will enter the standby
state or be shut down.
5. Lock control duration, that is, the lock drive duration.
6. Attendance record quantity alarm: When the specified attendance record quantity is reached, the
machine will raise an alarm to remind the user.
7. Operation record quantity alarm: When the specified operation record quantity is reached, the
machine will raise an alarm to remind the user.
8. Duplicate record time: minimum interval for a user to record the same attendance state.
9. Baud rate for RS232/485 communication: The value 0 indicates the baud rate of 1200 bps, 1 indicates
2400 bps, 2 indicates 4800 bps, 3 indicates 9600 bps, 4 indicates 19200 bps, 5 indicates 38400 bps, 6
indicates 57600 bps, and Others indicates 115200 bps.
10. Parity check bit, return value of which is fixed at 0.
11. Stop bit, return value of which is fixed at 0.
12. Date separator, return value of which is fixed at 1.
13. Whether to enable network functions: The value 1 indicates enabling network functions and 0
indicates disabling network functions.
14. Whether to enable RS232.
15. Whether to enable RS485.
16. Whether to enable announcements.
17. Whether to perform high-speed comparison.
194
18. Idle mode, that is, the state of the machine during idle hours. The value 87 indicates shutdown and 88
indicates hibernation.
19. Automatic shutdown time: The default value is 255, which means that the machine will not
automatically shut down.
20. Automatic startup time: The default value is 55, which means that the machine will not automatically
start.
21. Automatic hibernation time: The default value is 255, which means that the machine will not
automatically enter the hibernation state.
22. Automatic ringing time 1: The default value is 65535, which means that the bell will not
automatically ring.
23. 1:N comparison threshold.
24. Registration threshold.
25. 1:1 comparison threshold.
26. Whether to display the matching score during verification.
27. Number of people that unlock the door concurrently.
28. Verify the card number only.
29. Network speed: The value 1 indicates 100M-H, 4 indicates 10M-F, 5 indicates 100M-F, 8 indicates
AUTO, and Others indicates 10M-H.
30. Whether a card must be registered.
31. Waiting time before the machine automatically returns to the initial state if no operation is performed.
32. Waiting time before the machine automatically returns to the initial state if no response is returned
after the PIN is input.
33. Waiting time before the machine automatically returns to the initial state if no operation is performed
after entering the menu.
34. Time format.
35. Whether 1:1 comparison is mandatory.
36 40. Automatic ringing time 2, 3, 4, 5, and 6: The default value is 65535, which means that the bell
will not automatically ring.
41 56. Automatic status change time 1 16: The default values are all -1, which means that the status
will not change automatically.
36. Wiegand failure ID.
37. Wiegand duress ID.
38. Wiegand zone bit.
39. Pulse width of Wiegand outputs.
40. Pulse interval of Wiegand outputs.
41. ID of the start sector on the MIFARE card where fingerprints are stored.
42. Total number of sectors on the MIFARE card where fingerprints are stored.
43. Number of fingerprints stored on the MIFARE card.
195
44. Whether to display the attendance status.
67-68. Meaningless.
45. TCP Comm Port.
46. UDP port.
47. Fingerprint algorithm version.
48. Face algorithm version.
49. Finger vein version
50. FaceFunOn.
51. PIN2Width.
52. IsSupportABCPin.
53. IMEFunOn.
54. IsSupportAlarmExt.
55. ~DCTZ.
56. ~DOTZ.
57. dwValue serves the input and output parameter. The input indicates the name of another option to be
obtained and the output is the value of this option. This function is similar to GetSysOption in this
case.
[Note] The values of the preceding time points are all digits, which can be converted into actual time
points. Specifically, convert a value into binary format, the least significant eight bits indicate the
minute and the most significant eight bits indicate the hour. For example, if the value is 2860, it is
101100101100 in binary, the least significant eight bits are 00101100, which is 44 in decimal, and the
most significant eight bits are 00001011, which is 11 in decimal. That is, the actual time point is
11:44.
Note
Applicable to BW, TFT, and IFACE devices
5.4.4
SetDeviceInfo
VARIANT_BOOL SetDeviceInfo(LONG dwMachineNumber, LONG dwInfo, LONG dwValue)
To set machine information, such as the language and duplicate record time.
Parameters
Parameter description:
description of
name
type param direction
param
196
dwMachineNumber LONG
dwInfo
dwValue
LONG
LONG
[in]
Machine ID
[in]
Information type,
ranging from 1-20,
80, 81. For details
about the meanings of
values, see the
description of
GetDeviceInfo
[in]
Information of the
type specified by
dwInfo
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
dwInfo specifies the information type, ranging from 1-20, 80, 81. For details about the meanings
of values, see the description of GetDeviceInfo.
Note
Applicable to BW, TFT and IFACE devices
5.4.5
SetDeviceTime
VARIANT_BOOL SetDeviceTime(LONG dwMachineNumber)
To set the time of the machine to be the same as that of the local computer. To set specified time,
see the description of SetDeviceTime2.
Parameters
Parameter description:
name
type param direction description of param
dwMachineNumber LONG
[in]
Machine ID
197
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
5.4.6
SetDeviceTime2
VARIANT_BOOL SetDeviceTime2(LONG dwMachineNumber, LONG dwYear, LONG
dwMonth, LONG dwDay, LONG dwHour, LONG dwMinute, LONG dwSecond)
To set the time of the machine.
Parameters
Parameter description:
name
type param direction description of param
dwMachineNumber LONG
[in]
Machine ID
dwYear
LONG
[in]
Year
dwMonth
LONG
[in]
Month
dwDay
LONG
[in]
Date
dwHour
LONG
[in]
Hour
dwMinute
LONG
[in]
Minute
dwSecond
LONG
[in]
Second
Returns
Value description:
198
name type
True
description of value
BOOL Function execution success
False BOOL Function execution failure
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
5.4.7
GetDeviceTime
VARIANT_BOOL GetDeviceTime(LONG dwMachineNumber, LONG* dwYear, LONG*
dwMonth, LONG* dwDay, LONG* dwHour, LONG* dwMinute, LONG* dwSecond)
To query the time of the machine.
Parameters
Parameter description:
name
type param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
dwYear
LONG*
[out]
Year
dwMonth
LONG*
[out]
Month
dwDay
LONG*
[out]
Date
dwHour
LONG*
[out]
Hour
dwMinute
LONG*
[out]
Minute
dwSecond
LONG*
[out]
Second
Returns
Value description:
name type
description of value
199
True
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
5.4.8
GetSerialNumber
VARIANT_BOOL GetSerialNumber(LONG dwMachineNumber, BSTR* dwSerialNumber)
To query the serial number of the machine.
Parameters
Parameter description:
name
type param direction description of param
dwMachineNumber
LONG
[in]
Machine ID
dwSerialNumber
BSTR*
[out]
Serial number
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to BW, TFT, and IFACE devices
5.4.9
GetProductCode
VARIANT_BOOL GetProductCode(LONG dwMachineNumber, BSTR* lpszProductCode)
200
To query the product code of the machine.
Parameters
Parameter description:
name
type param direction
dwMachineNumber
description of param
LONG
[in]
Machine ID
lpszProductCode BSTR*
[out]
Product code
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
5.4.10
GetFirmwareVersion
VARIANT_BOOL GetFirmwareVersion(LONG dwMachineNumber, BSTR* strVersion)
To query the firmware version of the machine.
Parameters
Parameter description:
name
type param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
strVersion
BSTR*
[out]
Firmware version of the
machine
Returns
Value description:
201
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
5.4.11
GetSDKVersion
VARIANT_BOOL GetSDKVersion(BSTR* strVersion)
To query the SDK version.
Parameters
Parameter description:
name
type param direction description of param
strVersion BSTR*
[out]
SDK version
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
5.4.12
GetDeviceIP
VARIANT_BOOL GetDeviceIP(LONG dwMachineNumber, BSTR* IPAddr)
202
To query the IP address of the machine.
Parameters
Parameter description:
description of
name
type param direction
param
dwMachineNumber
LONG
[in]
Machine ID
IPAddr
BSTR*
[out]
IP address
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
5.4.13
SetDeviceIP
VARIANT_BOOL SetDeviceIP(LONG dwMachineNumber, BSTR IPAddr)
To set the IP address of the machine.
Parameters
Parameter description:
description of
name
type param direction
param
dwMachineNumber LONG
[in]
Machine ID
203
IPAddr
BSTR
[in]
IP address
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
5.4.14
GetDeviceMAC
VARIANT_BOOL GetDeviceMAC(LONG dwMachineNumber, BSTR* sMAC)
To query the MAC address of the machine.
Parameters
Parameter description:
description of
name
type param direction
param
dwMachineNumber
LONG
[in]
Machine ID
sMAC
BSTR*
[out]
MAC address
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
204
Attention
Note
Applicable to BW, TFT and IFACE devices
5.4.15
SetDeviceMAC
VARIANT_BOOL SetDeviceMAC(LONG dwMachineNumber, BSTR sMAC)
To set the MAC address of the machine.
Parameters
Parameter description:
description of
name
type param direction
param
dwMachineNumber LONG
sMAC
BSTR
[in]
Machine ID
[in]
MAC address
Returns
Value description:
name
type
description of value
True
BOOL
Function execution success
False
BOOL
Function execution failure
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
5.4.16
GetWiegandFmt
VARIANT_BOOL GetWiegandFmt(LONG dwMachineNumber, BSTR* sWiegandFmt)
To query the Wiegand format of the machine.
Parameters
Parameter description:
205
description of
name
type param direction
param
dwMachineNumber
LONG
[in]
Machine ID
sWiegandFmt
BSTR*
[out]
Wiegand format
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
5.4.17
SetWiegandFmt
VARIANT_BOOL SetWiegandFmt(LONG dwMachineNumber, BSTR sWiegandFmt)
To set the Wiegand format of the machine.
Parameters
Parameter description:
description of
name
type param direction
param
dwMachineNumber LONG
sWiegandFmt
BSTR
[in]
Machine ID
[in]
Wiegand format
Returns
Value description:
206
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
5.4.18
GetCardFun
VARIANT_BOOL GetCardFun(LONG dwMachineNumber, LONG* CardFun)
To query whether the machine supports the RF card.
Parameters
Parameter description:
description of
name
type param direction
param
dwMachineNumber
LONG
[in]
Machine ID
CardFun
LONG*
[in]
Whether the RF card
is supported
Returns
Value description:
name
type
description of value
True
BOOL
Function execution success
False
BOOL
Function execution failure
See also
Attention
If the value of CardFun is 1, the machine supports only the RF card. If the value is 2, both the RF
card and fingerprints are supported. If the value is 0, the RF card is not supported.
207
Note
Applicable to BW, TFT and IFACE devices
5.4.19
SetDeviceCommPwd
VARIANT_BOOL SetDeviceCommPwd(LONG dwMachineNumber, LONG CommKey)
To set the communication password of the machine, which will be saved on the machine.
Parameters
Parameter description:
description of
name
type param direction
param
dwMachineNumber LONG
CommKey
LONG
[in]
Machine ID
[in]
Communication
password
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
5.4.20
SetCommPassword
VARIANT_BOOL SetCommPassword(LONG CommKey)
To set the communication password of the PC. A connection can be set up between the machine
and the PC only if their communication passwords are the same.
Parameters
Parameter description:
208
name
type param direction
CommKey LONG
[in]
description of param
Communication password
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
5.4.21
QueryState
VARIANT_BOOL QueryState(LONG* State)
To query the current status of the machine.
Parameters
Parameter description:
name
type param direction
State LONG*
[out]
description of param
Current status of the
machine
Returns
Value description:
name
type description of value
True
BOOL
Function execution success
False BOOL
Function execution failure
See also
209
Attention
State specifies the current status of the machine. The meanings of the values are as follows:
0 Waiting state
1 Fingerprint registration state
2 Fingerprint identification state
3 Menu access state
4 Busy state (handling other work)
5 State of waiting for card writing
Note
Applicable to BW, TFT and IFACE devices
5.4.22
GetVendor
VARIANT_BOOL GetVendor(BSTR* strVendor)
To query the manufacturer of the machine.
Parameters
Parameter description:
name
type param direction description of param
strVendor BSTR*
[in]
Manufacturer of the
machine
Returns
Value description:
name type
True
description of value
BOOL Function execution success
False BOOL Function execution failure
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
5.4.23
GetDeviceStrInfo
VARIANT_BOOL GetDeviceStrInfo(LONG dwMachineNumber, LONG dwInfo, BSTR* Value)
To query the delivery time of the machine.
210
Parameters
Parameter description:
name
type param direction description of param
dwMachineNumber
LONG
[in]
Machine ID
dwInfo
LONG
[in]
It can be set only to 1
Value
BSTR*
[out]
Delivery time of the
machine
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
dwInfo can be set only to 1.
Note
Applicable to BW, TFT and IFACE devices
5.4.24
GetPlatform
VARIANT_BOOL GetPlatform(LONG dwMachineNumber, BSTR* Platform)
To query the platform of the machine.
Parameters
Parameter description:
description of
name
type param direction
param
dwMachineNumber
LONG
[in]
Machine ID
Platform
BSTR*
[out]
Platform name
211
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
5.4.25
ReadAOptions
VARIANT_BOOL ReadAOptions (LONG dwMachineNumber, BSTR Option, BSTR Value)
Read the values of specified configuration parameters from the device. The parameters beginning
with "~" are skipped.
Parameter
Parameter description:
param
name
type
description of param
direction
dwMachineNumber
LONG
[in]
Machine equipment
number
Option
BSTR
[in]
parameter name
Value
BSTR
[in]
Parameter value
Returns
Value description:
name type
True
description of value
BOOL Function execution success
212
False BOOL Function execution failure
See also
Attention
Note
Applicable to BW, TFT devices
5.4.26
GetSysOption
VARIANT_BOOL GetSysOption (LONG dwMachineNumber, BSTR Option, BSTR Value)
Get parameter values
Parameter
Parameter description:
param
name
type
description of param
direction
dwMachineNumber
LONG
[in]
Machine equipment
number
Option
BSTR
[in]
parameter name
Value
BSTR
[in]
Parameter value
Returns
Value description:
name type
True
description of value
BOOL Function execution success
False BOOL Function execution failure
See also
Attention
213
Parameter name. When the parameter is the character string "~ZKFPVersion", if the returned
Value is 10, the current device uses ZKFinger10.0; if the returned Value is null or 9, the current
device uses ZKFinger9.0.
Note
Applicable to BW, TFT devices
5.4.27
SetSysOption
VARIANT_BOOL SetSysOption(LONG dwMachineNumber, BSTR Option, BSTR Value)
To set parameter value.
Parameters
Parameter description:
name
type param direction
dwMachineNumber LONG
description of param
[in]
Machine ID
Option
BSTR
[in]
Parameter name
Value
BSTR
[in]
Parameter value
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to BW and TFT devices
5.4.28
GetDeviceStatusEx
LONG GetDeviceStatusEx(LONG dwMachineNumber)
To get the status of the P2P devices.
Parameters
Parameter description:
214
name
type param direction
dwMachineNumber LONG
description of param
[in]
Machine ID
Returns
Value description:
name
type
description of value
1
LONG
Machine is reading data
2
LONG
Machine is writing data
3
LONG
Machine is working
greater than 3 LONG
The machine is free and the software can
operate the machine
See also
Attention
P2P devices could not do multi-threaded work. Must get the device status and when the device
isfree the software can operate the machine.
Note
Applicable to some P2P devices, such as the K Pro series attendace machine
5.5 Others
5.5.1
Device Control Functions
5.5.1.1 ClearAdministrators
VARIANT_BOOL ClearAdministrators(LONG dwMachineNumber)
To clear the operation rights of all administrators.
Parameters
Parameter description:
name
type param direction
dwMachineNumber LONG
description of param
[in]
Machine ID
Returns
215
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
5.5.1.2 EnableDevice
VARIANT_BOOL EnableDevice(LONG dwMachineNumber, VARIANT_BOOL bFlag)
To enable or disable the machine. After the machine is disabled, the fingerprint, keyboard, and
card modules are unavailable.
Parameters
Parameter description:
name
type param direction
dwMachineNumber LONG
bFlag
BOOL
description of param
[in]
Machine ID
[in]
Flag that indicates whether the
machine is enabled. The value 1
indicates that the machine is
enabled and 0 indicates that the
machine is disabled.
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
216
Attention
Note
Applicable to BW, TFT and IFACE devices
5.5.1.3 EnableClock
VARIANT_BOOL EnableClock(LONG Enabled)
To enable or disable the display of the colon (:) in the time of the machine. The colon is displayed
on the main screen of the machine if enabled, and not displayed if disabled.
Parameters
Parameter description:
name
type param direction
Enabled LONG
[in]
description of param
Whether to enable the display of the
colon. The value 1 indicates
enabling the display of the colon
and 0 indicates disabling the
display of the colon.
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
5.5.1.4 DisableDeviceWithTimeOut
VARIANT_BOOL DisableDeviceWithTimeOut(LONG dwMachineNumber, LONG TimeOutSec)
To disable the machine for a period of time.
Parameters
Parameter description:
217
name
type param direction
dwMachineNumber LONG
TimeOutSec
LONG
description of param
[in]
Machine ID
[in]
Time period during which the
machine is disabled
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
5.5.1.5 PowerOffDevice
VARIANT_BOOL PowerOffDevice(LONG dwMachineNumber)
To shut down the machine.
Parameters
Parameter description:
name
type param direction
dwMachineNumber LONG
description of param
[in]
Machine ID
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
218
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
5.5.1.6 RestartDevice
VARIANT_BOOL RestartDevice(LONG dwMachineNumber)
To restart the machine.
Parameters
Parameter description:
name
type param direction
dwMachineNumber LONG
description of param
[in]
Machine ID
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
5.5.2
Online Registration Functions
5.5.2.1 StartEnroll
VARIANT_BOOL StartEnroll(LONG UserID, LONG FingerID)
To register a user. The machine will then enter the user registration state and waits for the user to
scan fingerprints.
Parameters
Parameter description:
219
name
type param direction
UserID
description of param
LONG
[in]
ID of the user to be registered
FingerID LONG
[in]
Index of the fingerprint of the
user, ranging from 0 to 9
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
After this function is invoked and the user scans fingerprints for three times, the machine may not
respond when the user scans fingerprints again. In this case, invoke StartIdentify to enable the
machine to enter the waiting state.
Note
Applicable to BW
5.5.2.2 StartEnrollEx
VARIANT_BOOL StartEnrollEx(BSTR UserID, LONG FingerID, LONG Flag)
To register a user. The machine will then enter the user registration state and waits for the user to
scan fingerprints.
Parameters
Parameter description:
name
UserID
type param direction
description of param
BSTR
[in]
ID of the user to be registered
FingerID LONG
[in]
Index of the fingerprint of the
user, ranging from 0 to 9
[in]
Flag that indicates whether the
fingerprint template is valid or a
Flag
LONG
220
duress fingerprint
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
1. After this function is invoked and the user scans fingerprints for three times, the machine may
not respond when the user scans fingerprints again. In this case, invoke StartIdentify to enable the
machine to enter the waiting state.
2. The Flag parameter indicates whether the fingerprint template is valid, or the fingerprint
template is a duress fingerprint. The value 0 indicates that the fingerprint template is invalid, 1
indicates that the fingerprint template is valid, and 3 indicates that the fingerprint template is a
duress fingerprint.
Note
Applicable to TFT
5.5.2.3 StartVerify
VARIANT_BOOL StartVerify(LONG UserID, LONG FingerID)
To start 1:1 comparison.
Parameters
Parameter description:
name
UserID
type param direction
description of param
LONG
[in]
ID of the user to be verified
FingerID LONG
[in]
Index of the fingerprint of the
user, ranging from 0 to 9
Returns
Value description:
221
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to BW and TFT devices
5.5.2.4 StartIdentify
VARIANT_BOOL StartIdentify()
To start 1:N comparison. Then the machine will enter the 1:N verification state.
Parameters
None
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to BW and TFT devices
5.5.2.5 CancelOperation
VARIANT_BOOL CancelOperation()
To cancel the current fingerprint registration state of the machine.
Parameters
None
Returns
Value description:
222
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to BW and TFT devices
5.5.3
Card Operation Functions
5.5.3.1 WriteLCD
VARIANT_BOOL WriteLCD(LONG Row, LONG Col, BSTR Text)
To write data. Specifically, this function is used to write a character string to any row of any
column on the machine.
Parameters
Parameter description:
name type param direction
description of param
Row
LONG
[in]
Start row
Col
LONG
[in]
Start column
Text
BSTR
[in]
Content to be written on
the screen of the machine
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
223
Note
Applicable to BW
5.5.3.2 ClearLCD
VARIANT_BOOL ClearLCD()
To clear the screen of the machine. Specifically, this function is used to clear all information
displayed on the LCD screen of the machine.
Parameters
None
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to BW
5.5.3.3 WriteCard
VARIANT_BOOL WriteCard(LONG dwMachineNumber, LONG dwEnrollNumber,
LONG dwFingerIndex1, BYTE* TmpData1, LONG dwFingerIndex2, BYTE* TmpData2,
LONG dwFingerIndex3, BYTE* TmpData3, LONG dwFingerIndex4, BYTE* TmpData4)
To write a specified user and the fingerprint template of the user to the MF card. After this
function is invoked, the user needs to punch the MF card on the machine.
Parameters
Parameter description:
name
type param direction
description of param
dwMachineNumber
LONG
[in]
Machine ID
dwEnrollNumber
LONG
[in]
User ID
224
dwFingerIndex1
LONG
[in]
Fingerprint index, ranging from 0
to 3
TmpData1
BYTE*
[in]
Fingerprint template
corresponding to the fingerprint
index
dwFingerIndex2
LONG
[in]
Fingerprint index, ranging from 0
to 3
TmpData2
BYTE*
[in]
Fingerprint template
corresponding to the fingerprint
index
dwFingerIndex3
LONG
[in]
Fingerprint index, ranging from 0
to 3
TmpData3
BYTE*
[in]
Fingerprint template
corresponding to the fingerprint
index
dwFingerIndex4
LONG
[in]
Fingerprint index, ranging from 0
to 3
[in]
Fingerprint template
corresponding to the fingerprint
index
TmpData4
BYTE*
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
TmpData1 cannot be left blank
Note
Applicable to BW, TFT and IFACE devices
225
5.5.3.4 EmptyCard
VARIANT_BOOL EmptyCard(LONG dwMachineNumber)
To clear the MF card.
Parameters
Parameter description:
name
type param direction
dwMachineNumber LONG
description of param
[in]
Machine ID
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
5.5.4
Others
5.5.4.1 GetLastError
GetLastError(LONG* dwErrorCode)
To query information about the last error.
Parameters
Parameter description:
name
type param direction
dwErrorCode LONG*
description of param
[out]
Error code
Value description:
226
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
The dwErrorCode parameter specifies the error code. The values are described as follows:
1. During connection, the following error codes may be returned:
0 Connected successfully
-1 Failed to invoke the interface
-2 Failed to initialize
-3 Failed to initialize parameters
-5 Data mode read error
-6 Wrong password
-7 Reply error
-8 Receive timeout
-307 Connection timeout
In invoking other interfaces, the following error codes may be returned:
-201 Device is busy
-199 New Mode
-103 device send back error of face version error
-102 face template version error, like 8.0 face template send to 7.0 device
-101 malloc memory failed
-100 Not supported or the data does not exist
-10 The length of transmitted data is incorrect
-5 Data already exists
-4 Insufficient space
-3 Wrong size
-2 File read/write error
-1 The SDK is not initialized and needs to be reconnected
0 Data not found or duplicate data
1 Correct operation
4 Parameter error
101 Buffer allocation error
102 repeat invoking
2. Underlying error codes:
-12001 Socket creation timeout (connection timeout)
-12002 Insufficient memory
-12003 Wrong Socket version
-12004 Not TCP protocol
227
-12005 Waiting timeout
-12006 Data transmission timeout
-12007 Data reading timeout
-12008 Failed to read Socket
-13009 Waiting event error
-13010 Exceeded retry attempts
-13011 Wrong reply ID
-13012 Checksum error
-13013 Waiting event timeout
-13014 DIRTY_DATA
-13015 Buffer size too small
-13016 Wrong data length
-13017 Invalid data read1
-13018 Invalid data read2
-13019 Invalid data read3
-13020 Data loss
-13021 Memory initialization error
-15001 Invoking return value of status key issued by SetShortkey interface repeatedly
-15002 Invoking return value of description issued by SetShortkey interface repeatedly
-15003 The two level menu is not opened in the device, and the data need not be issued
3. getdevicedata and setdevicedata invocation error codes
-15100 Error occurs in obtaining table structure
-15101 The condition field does not exist in the table structure
-15102 Inconsistency in the total number of fields
-15103 Inconsistency in sorting fields
-15104 Memory allocation error
-15105 Data parsing error
-15106 Data overflow as the transmitted data exceeds 4M
-15108 Invalid options
-15113 Data parsing error: table ID not found
-15114 A data exception is returned as the number of fields is smaller than or equal to 0
-15115 A data exception is returned as the total number of table fields is inconsistent with the
total number of fields of the data
4. Firmware error codes:
2000 Return OK to execute
-2001 Return Fail to execute command
-2002 Return Data
-2003 Regstered event occorred
-2004 Return REPEAT Command
-2005 Return UNAUTH Command
0xffff Return Unknown Command
-4999 Device parameter read error
-4998 Device parameter write error
-4997 The length of the data sent by the software to the device is incorrect
228
-4996 A parameter error exists in the data sent by the software to the device
-4995 Failed to add data to the database
-4994 Failed to update the database
-4993 Failed to read data from the database
-4992 Failed to delete data in the database
-4991 Data not found in the database
-4990 The data amount in the database reaches the limit
-4989 Failed to allocate memory to a session
-4988 Insufficient space in the memory allocated to a session
-4987 The memory allocated to a session overflows
-4986 File does not exist
-4985 File read failure
-4984 File write failure
-4983 Failed to calculate the hash value
-4982 Failed to allocate memory
Note
This interface is applicable to the new architecture firmware.
5.5.4.2 GetHIDEventCardNumAsStr
VARIANT_BOOL GetHIDEventCardNumAsStr(BSTR* strHIDEventCardNum)
To query the number of the card that is punched most recently.
Parameters
Parameter description:
name
type param direction
strHIDEventCardNum BSTR*
[out]
Number of the punched card
Returns
Value description:
name type
True
description of param
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
229
Applicable to BW, TFT and IFACE devices
5.5.4.3 CaptureImage
VARIANT_BOOL CaptureImage(VARIANT_BOOL FullImage, LONG* Width, LONG* Height,
BYTE* Image, BSTR ImageFile)
To capture an image of the finger of which the fingerprint is being scanned.
Parameters
Parameter description:
name
type param direction
description of param
FullImage
BOOL
[in]
Whether to capture an image of
the entire finger. The value
True indicates capturing an
image of the entire finger and
False indicates capturing an
image of only the fingerprint.
Width
LONG*
[in]
Width of the captured image
Height
LONG*
[in]
Height of the captured image
Image
BYTE*
[in]
Fingerprint image in binary
format
[in]
Name of the file of captured
image to be saved (including
the path)
ImageFile
BSTR
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
230
5.5.4.4 UpdateFirmware
VARIANT_BOOL UpdateFirmware(BSTR FirmwareFile)
To upgrade the firmware. To use this function, obtain the firmware from the technical support
engineers of our company beforehand.
Parameters
Parameter description:
name
type param direction
FirmwareFile BSTR
[in]
description of param
Name of the firmware file to be
upgraded (including the path)
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
5.5.4.5 BeginBatchUpdate
VARIANT_BOOL BeginBatchUpdate(LONG dwMachineNumber, LONG UpdateFlagl)
To get ready for uploading data in batches. For example, if you invoke this function before
uploading data such as fingerprint templates or user information, the SDK will temporarily store
the data in the buffer. Then you can invoke BatchUpdate to upload the data to the machine.
Parameters
Parameter description:
name
type param direction
dwMachineNumber LONG
description of param
[in]
Machine ID
231
UpdateFlagl
LONG
Whether to overwrite the original
fingerprint template
[in]
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
The UpdateFlag1 parameter specifies whether to overwrite the original fingerprint template if a
fingerprint with the same index already exists when you upload a fingerprint template. The value
1 indicates overwriting the original fingerprint template and 0 indicates not overwriting the
original fingerprint template.
Note
Applicable to BW, TFT and IFACE devices
5.5.4.6 BatchUpdate
VARIANT_BOOL BatchUpdate(LONG dwMachineNumber)
To upload data in batches. Generally you are advised to invoke BeginBatchUpdate to upload the
data to the buffer before invoking this function.
Parameters
Parameter description:
description of
name
type param direction
param
dwMachineNumber LONG
[in]
Machine ID
Returns
Value description:
name type
description of value
232
True
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
5.5.4.7 CancelBatchUpdate
VARIANT_BOOL CancelBatchUpdate(LONG dwMachineNumber)
To cancel bulk data uploading. You can invoke this function after invoking BeginBatchUpdate
but before invoking BatchUpdate. This function aims to release the buffer allocated for bulk data
uploading.
Parameters
Parameter description:
name
type param direction description of param
dwMachineNumber LONG
[in]
Machine ID
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
5.5.4.8 PlayVoice
VARIANT_BOOL PlayVoice(LONG Position, LONG Length)
To play announcements with specified consecutive indexes. The indexes depend on the machine.
You can view the indexes, which range from 0 to 11, in voice testing on the machine.
Parameters
233
Parameter description:
name
type param direction description of param
Position LONG
Length
LONG
[in]
Index of the start
announcement
[in]
Index of the end
announcement
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
5.5.4.9 PlayVoiceByIndex
VARIANT_BOOL PlayVoiceByIndex(LONG Index)
To play an announcement with the specified index. The index depends on the machine. You can
view the index, which ranges from 0 to 11, in voice testing on the machine.
Parameters
Parameter description:
name type param direction
Index LONG
[in]
description of param
Index of the announcement to be played
Returns
Value description:
name type
description of value
234
True
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to BW, TFT and IFACE devices
5.5.4.10 ReadAttRule
VARIANT_BOOL ReadAttRule(LONG dwMachineNumber)
To read the attendance rule of the machine. This function supports OP1000.
Parameters
Parameter description:
name
type param direction
dwMachineNumber LONG
description of param
[in]
Machine ID
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to BW devices
5.5.4.11 SaveTheDataToFile
VARIANT_BOOL SaveTheDataToFile(LONG dwMachineNumber, BSTR TheFilePath,
LONG FileFlag)
To save the data in the buffer as a file. This function supports OP1000.
Parameters
Parameter description:
235
name
type param direction
dwMachineNumber LONG
description of param
[in]
Machine ID
TheFilePath
BSTR
[in]
Path for saving the file
FileFlag
LONG
[in]
File type flag
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
The FileFlag parameter specifies the file type. The values are described as follows:
1 Attendance records
2 User
3 Attendance rule
4 Department list
5 Shift
Note
Applicable to BW devices
5.5.4.12 ReadTurnInfo
VARIANT_BOOL ReadTurnInfo(LONG dwMachineNumber)
To read the shift information on the machine. This function supports OP1000.
Parameters
Parameter description:
name
type param direction
dwMachineNumber LONG
description of param
[in]
Machine ID
Returns
Value description:
236
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
Note
Applicable to BW devices
5.5.4.13 SSR_OutPutHTMLRep
VARIANT_BOOL SSR_OutPutHTMLRep(LONG dwMachineNumber, BSTR dwEnrollNumber,
BSTR AttFile, BSTR UserFile, BSTR DeptFile, BSTR TimeClassFile, BSTR AttruleFile,
LONG BYear, LONG BMonth, LONG BDay, LONG BHour, LONG BMinute, LONG BSecond,
LONG EYear, LONG EMonth, LONG EDay, LONG EHour, LONG EMinute, LONG ESecond,
BSTR TempPath, BSTR OutFileName, LONG HTMLFlag, LONG resv1, BSTR resv2)
To generate the attendance report of a user within the specified time period in HTML format.
This function supports OP1000.
Parameters
Parameter description:
name
type param direction
description of param
dwMachineNumber LONG
[in]
Machine ID
dwEnrollNumber
BSTR
[in]
User ID
AttFile
BSTR
[in]
Name of the attendance record file
UserFile
BSTR
[in]
Name of the user information file
DeptFile
BSTR
[in]
Name of the department information
file
TimeClassFile
BSTR
[in]
Name of the shift information file
AttruleFile
BSTR
[in]
Name of the attendance rule file
BYear
LONG
[in]
Start time of the time period
237
BMonth
LONG
[in]
End time of the time period
BDay
LONG
[in]
Start time of the time period
BHour
LONG
[in]
Start time of the time period
BMinute
LONG
[in]
Start time of the time period
BSecond
LONG
[in]
Start time of the time period
EYear
LONG
[in]
End time of the time period
EMonth
LONG
[in]
End time of the time period
EDay
LONG
[in]
End time of the time period
EHour
LONG
[in]
End time of the time period
EMinute
LONG
[in]
End time of the time period
ESecond
LONG
[in]
End time of the time period
TempPath
BSTR
[in]
Path where other exception files
are saved
OutFileName
BSTR
[in]
Attendance report file name
(including the path)
HTMLFlag
LONG
[in]
HTML report format
resv1
LONG
[in]
Reserved
resv2
BSTR
[in]
Flow report name
Returns
Value description:
name type
True
description of value
BOOL
Function execution success
False BOOL
Function execution failure
See also
Attention
The HTMLFlag parameter specifies the HTML report type. The values are described as follows:
238
1 Flow report
2 Exception report
3 Statistics report
Note
Applicable to BW devices
5.5.4.14 SendFileByType
param
name
type
description of param
direction
dwMachineNumber
LONG
[in]
Machine equipment number
FileName
BSTR
[in]
File full path name
iType
LONG
[in]
File type
5.5.4.15 SetCommProType
VARIANT_BOOL SetCommProType(LONG, proType)
Set the priority to use PULL or Standlone SDK to connect the device.
Parameters
Parameter description:
name
type
param direction
description of param
proType
LONG
[in]
Priority protocol type
Returns
Value description:
name
type
description of value
True
BOOL
Function execution success
False
BOOL
Function execution failure
See also
239
Attention
proType=1 Priority to use the Standlone SDK protocol proType=2 Priority to use the PULL SDK
protocol Default to use Standlone SDK protocol to connect devices. If the customer does not
develop PULL devices, this interface is not recommended by the developer.
Note
No dependency with device.
5.5.4.16 SetCommProType
VARIANT_BOOL SetCommProType(LONG proType)
Set the priority to use PULL or Standlone SDK to connect the device.
Parameters
Parameter description:
name
type
param direction
description of param
proType
LONG
[in]
Priority protocol type
Returns
Value description:
name
type
description of value
True
BOOL
Function execution success
False
BOOL
Function execution failure
See also
Attention
proType=1 Priority to use the Standlone SDK protocol proType=2 Priority to use the PULL SDK
protocol Default to use Standlone SDK protocol to connect devices. If the customer does not
develop PULL devices, this interface is not recommended by the developer.
Note
No dependency with device.
5.5.4.17 GetConnectStatus
VARIANT_BOOL GetConnectStatus(LONG* dwErrorCode)
Get the error code return from the function BatchUpdate()
240
Parameters
Parameter description:
name
type
param direction
description of param
dwErrorCode
LONG*
[out]
Error code
Returns
Value description:
name
type
description of value
True
BOOL
Function execution success
False
BOOL
Function execution failure
See also
Attention
When (dwErrorCode >= -11004 && dwErrorCode <= -10004), the software will disconnect and
re-connect the device.
Note
Only used to get the error code return from the function BatchUpdate(), without the limitation of
devices.
5.5.4.18 SetDeviceTableData
VARIANT_BOOL SendFileByType(LONG dwMachineNumber, BSTR TableName, BSTR Datas,
BSTR Options, LONG* Count)
This function applies only to the time and attendance applications that comply with the PULL
protocol in the new firmware. Used to set and insert data (such as time segments, user
information, and leaves settings) into a device. The data can be one or more records. If the
primary key of an inserted record already exists in the device, the original record is overwritten.
Parameters
name
type
param direction
description of param
dwMachineNumber
LONG
[in]
Machine equipment number
TableName
BSTR
[in]
Data table name
Datas
BSTR
[in]
Data record representation
241
Options
BSTR
[in]
Default empty, use for expansion
Count
LONG*
[out]
The number of records which were
issued successfully
Returns
Value description:
name
type
description of value
True
BOOL
Function execution success
False
BOOL
Function execution failure
See also
Attention
Indication of data records. Data is in the text format. Multiple records are separated by \r\n.
Various pairs of "field=value" are separated by \t.
Note
5.5.4.19 SearchDevice
VARIANT_BOOL SearchDevice(BSTR commType, BSTR address, BSTR* DevBuffer, LONG
DevBufferSize)
Use web search devices.
Parameters
Parameter description:
name
type
param direction
description of param
commType
BSTR
[in]
Communication type
address
BSTR
[in]
Communication data
DevBuffer
BSTR*
[out]
Device list
DevBufferSize
LONG
[in]
Size of device list
Returns
Value description:
242
name
type
description of value
True
BOOL
Function execution success
False
BOOL
Function execution failure
See also
Attention
commType=UDP
address=255.255.255.255 The return data include the IP address, serial number, firmware version,
etc.
Note
Applicable to some customized devices
243
6 FAQs
6.1 How to Download Attendance Records?
First, use ReadGeneralLogData to read all attendance records and write them into the memory.
Then, use SSR_GetGeneralLogData repeatedly to obtain attendance records. When
SSR_GetGeneralLogData returns False, it means that all attendance records are obtained. Then,
you can write the obtained records into database or display them in other forms to finish
downloading. You can follow the same steps to down operation records.
Note
BW device use GetGeneralLogData instead of SSR_GetGeneralLogData
6.2 How to Create a User Online?
First, use SSR_SetuserInfo to write user information (such as enrollment number, password, and
name) into the device. Then, use SSR_SetUserTmpStr/SSR_SetUerTmp to set fingerprint
templates for the user. This method improves enrollment efficiency and is suitable when user
information has been collected and stored in media such as database.
To upload user information and corresponding fingerprint templates in batches, use
BeginBatchUpdata and SetUserInfo together with BarchUpdata, EnableDevice, or RefreshData.
For details, see demo program.
Note
BW device use SetuserInfo instead of SSR_SetuserInfo, SetUserTmpStr instead of
SSR_SetUserTmpStr, SetUerTmp instead of SSR_SetUerTmp.
6.3 How to Import or Download Data from USB Disk?
Many existing offline products support data download from USB disks. Many customers are
concerned about data formats of USB disks. As the downloaded data formats are complex,
ZKSoftware provides a tool for importing data from USB disks to database. Database is open for
customers to download data. In addition, ZKSoftware also provides examples on how to process
data files (*.dat, etc.) collected from USB disks and how to write the data into specified data files.
All structs adopt 1 byte alignment mode.
Data in USB disks include user information, fingerprint templates, face templates, attendance
records, and short messages. Detailed data structures are used in demo program. They are
described briefly below:
User data structure:
typedef struct _User_{
U16 PIN; //Internal number of a user
U8 Privilege;
char Password[8];
244
char Name[24];
U8 Card[4];
U8 Group;
U16 TimeZones[4];
char PIN2[24];
//User ID
}
Data structure of 9.0 fingerprint template:
typedef struct _Template_{
U16 Size;
//fingerprint template length
U16 PIN;
//internal user ID, which corresponds to PIN2 in user table
BYTE FingerID;
// fingerprint backup index
BYTE Valid;
BYTE Template[MAXTEMPLATESIZE]; //maximize template length
}
//MAXTEMPLATESIZE
602 Bytes
Data structure of template.fp10:
typedef struct _Template_{
U16 Size;
//entire structure data size
U16 PIN;
//user ID
BYTE FingerID;
//fingerprint index
BYTE Valid;
//flag
BYTE *Template; //template
}
Attendance record,
struct _AttLog_{
U16 PIN;
U8 PIN2[24];
BYTE verified;
time_t time_second;
BYTE status;
U32 workcode;
BYTE reserved[4];
}
Exported as a text file:
attlog.dat format
explanation:
245
segment:
BadgeNumber(employee number),
checktime,
DeviceID,
checktype(check status),
VerifyCode(verification ways:password or fingerprint or other)
Workcode
There is an Ascii code #9(Tab) between each segment. When development, move to the segment
value you want to choose by "Tab".
If the device has the output data protection function, the serial number of the current device is
displayed in first line and the hash value in the last line of the file to which attendance records are
exported from USB disk.
Data structure of SMS
typedef struct _SMS_{
BYTE Tag;
U16 ID;
//category
//data content flag. 0 indicates that the record is invalid.
U16 ValidMinutes; //valid minutes. 0 indicates that the record is permanently valid.
U16 Reserved;
U32 StartTime;
//start time
BYTE Content[MAX_SMS_CONTENT_SIZE+1];
}
//short message content
// MAX_SMS_CONTENT_SIZE 60 Bytes
Data structure between SMS and user pin//user->sms,udata.dat
typedef struct _UData_{
U16 PIN;
//0 indicates that the record is invalid
U16 SmsID;
}GCC_PACKED TUData, *PUData; //4Bytes
Data structure of face template:
typedef struct _FaceTmp_{
U16 Size;//face template size
U16 PIN;//user ID
BYTE FaceID;//Face ID
BYTE Valid;//flag
U16 Reserve;//reserve
U32 ActiveTime;
U32 VfCount;//Verify Count
246
BYTE FaceTmp[FACE_TMP_MAXSIZE]
}
//FACE_TMP_MAXSIZE=1024*2+512
Note
BW device use User data structure:
typedef struct _User_{
U16 PIN; //Internal number of a user
U8 Privilege;
char Password[5];
char Name[8];
U8 Card[5];
//ID No which used for store the relevant ID No
U8 Group;
//the Group user belongs to
U16 TimeZones; //user can use time zone
U32 PIN2;
//User ID
}
6.4 How to Use Biokey to Write the Collected Fingerprint Templates
Offline?
When a fingerprint is collected, Biokey usually obtains the fingerprint template during
enrollment. For example, the currently enrolled fingerprint template can be obtained via
OnEnroll. After obtaining the fingerprint template, Biokey converts it into an offline fingerprint
template. Then, the template can be written into the device.
6.5 How to Obtain All Information of All Users?
Use ReadAllUserID to read IDs of all users and write them into memory. Then, use
SSR_GetAllUserInfo repeatedly to obtain EnrollNumber of users, and use SSR_GetUserInfo to
obtain user information. If necessary, you can also use SSR_GetUserTmpStr to obtain the
fingerprint templates in string form.
Note
BW device use GetAllUserInfo instead of SSR_GetAllUserInfo, GetUserInfo instead of
SSR_GetUserInfo, GetUserTmpStr instead of SSR_GetUserTmpStr.
6.6 How to Connect to the Device?
During connection, the device can be regarded as an independent PC. However, the IP address of
the device must match the IP address to be connected. Some devices, for example F4, support
serial port connection and network connection. Therefore, during different connections, you need
to set the device differently, modify communication mode, and set the controller switch to
TCP/IP or RS232/485. Otherwise, the connection may fail. Sometimes, if the device fails to be
connected due to busy serial ports, you can restart the program. If the application keeps
247
connecting to the device without being manually disconnected, you can use
DisableDeviceWithTimeOut to set the automatic disconnection time of the device. If some
connections are used to download or modify data via serial ports or network, you can use
EnableDevice to keep the device working and restore the connections after communication
finishes, so as to maintain data consistency and avoid unknown errors.
6.7 Password Is Invalid After SetUserInfo Is Used.
After SSR_SetUserInfo is called, Password may be set to null. If so, password verification will
fail. To keep the password unchanged when writing user information, use SSR_GetUserInfo to
obtain user password and transmit the password value to the Password parameter of
SSR_SetUserInfo before using SSR_SetUserInfo.
Note
BW device use SetUserInfo instead of SSR_SetUserInfo, GetUserInfo instead of
SSR_GetUserInfo.
6.8 How to Convert an Online Template into an Offline Template?
Use FPTempConvertNew to convert the collected templates into offline fingerprint templates.
See related descriptions of Biokey SDK for how to obtain the templates collected by Biokey.
FPTempConvertNew is used to convert binary fingerprint templates. Parameters temp1 and
temp2 are binary parameters. You can also use FPTempConvertNewStr to convert Biokey
fingerprint templates of string type into offline fingerprint templates.
6.9 Demo Program Fails to Connect to the Device.
After the attendance management program is installed, users can connect to the device by using
the attendance management program, but cannot connect to the device by using demo program.
The reason is that DLL is copied to the directory of the attendance management program but
registered in the installation directory during program installation. Generally, SDK loads controls
from the system directory. Therefore, if the SDK version in the system directory is different from
that in the attendance software directory, conflicts occur. (DLL function addresses of different
versions are different, but OCX functions are the same in programming. Therefore, the problem
is found only during runtime.)
Caution: The common procedure for registering the SDK in the system is as follows:
1. If an SDK has been already registered in the system, run regsvr32 /u zkemkeeper.dll to
unregister the original SDK.
2. Copy all DLLs to the system directory, for example, win2000 is located in winnt\system32.
3. Run regsvr32 "registration path\zkemkeeper.dll" to register the SDK.
4. Correctly load controls in development environment (learn the usage of development tool by
yourself. Relevant details are omitted here).
5. Try to use the SDK of the same version in development or running environment.
248
6.10 Offline Fingerprint Device Keeps Working After Being
Connected.
After connecting the SDK to the offline fingerprint device, use EnableDevice to keep the offline
fingerprint device working (see EnableDevice), so as to maintain data consistency and avoid
unknown errors. After the offline fingerprint device is working, the keypad and fingerprint sensor
stop working. After communication finishes, disconnect the SDK from the device or use
EnableDevice again to restore the offline fingerprint device to normal state.
DisableDeviceWithTimeOut is recommended.
6.11 Illegal Characters Are Displayed or Screen Display Is Abnormal
After Non-English Names or Short Messages Are Uploaded to the
Device.
First, check whether the device supports the specified language. For example, if the current
language of the device is English, but an Arabic name is uploaded to the device, the name cannot
be displayed normally. If the device already supports the language, but the name still cannot be
displayed, use related functions to convert the user name into UTF-8 format (for example, use
AnsiToUTF8() in Dephi), and then use SSR_SetUserInfo to upload the user name.
Note
BW device use SetUserInfo instead of SSR_SetUserInfo.
6.12 Card Management Problems
How to register a card in the device? How to obtain the user card?
The SDK has the cardnumber parameter. If this parameter is invisible in development
environment, use GetStrCardNumber and SetStrCardNumber instead.
For a user enrolled in the device, the card number is a kind of user information. When
SSR_SetUserInfo is used to set user information, cardnumber is automatically used as the card
number and set for the user.
The procedure for registering a card is as follows:
Set cardnumber -> Upload user information
The procedure for obtaining the card number of a user is as follows:
Obtain information of the specified user -> Obtain cardnumber
Note: The card number is internally defined as four unsigned bytes of long type. If VB does not
support four unsigned bytes, verification can be started after the last three bytes of the card
number are input (if the last three bytes are different from each other).
Note
BW device use SetUserInfo instead of SSR_SetUserInfo.
249
6.13 Firewall or Router Traversal
In most cases, the device to be connected needs to traverse firewalls or routers, and UDP socket
and port 4370 are used for SDK communication. Therefore, UDP and port 4370 must be enabled
on firewalls or routers. If the device traverses gateways via port mapping, the device can be
accessed via port number and IP address of routers. Generally, if UDP and port 4370 are enabled
and can be pinged, the device can be connected. Certainly, in the case of data download, network
connection must be considered. In addition, some devices that support SOAP ports can be
accessed via embedded Web Server and SOAP.
Caution: The zem100 series products can traverse internet via port mapping. For zem200
products, as the devices run on Linux, they can be accessed after the gateway is configured if the
local network environment supports gateway communication. Certainly, there are still some other
methods for accessing the device, for example, VPN and IP mapping. The connection scheme
should be selected according to specific network environments.
6.14 Difference between ZKFinger10.0 and ZKFinger9.0 and
Comparison between Templates
Algorithm performance: Compared with ZKFinger9.0, ZKFinger10.0 achieves better false
acceptance rate (FAR), false rejection rate (FRR), and enrollment rejection rate (ERR), better
image processing effect of low-quality fingerprints (for example, fingerprints are too dry or too
wet, or users have worn or injury), and 10 times faster comparison.
Template size: The size of a ZKFinger10.0 fingerprint template is about 1.6 KB. The size of a
ZKFinger9.0 fingerprint template is about 512B. When ZKFinger10.0 is used, a Mifare card with
at least 2 KB capacity should be used for data storage.
Template compatibility: The ZKFinger10.0 and ZKFinger9.0 fingerprint templates are
incompatible with each other. If a user who have already registered ZKFinger9.0 fingerprint
templates wants to use ZKFinger10.0, the user has to register fingerprint templates again, and
vice versa.
6.15 Uploading a Large Capacity of Fingerprints
Large capacity usually means over 1500 fingerprints. Some devices can hold 8000 fingerprints or
more. Fingerprint templates must be uploaded in batches. In this mode, the upload is much faster.
For how to upload fingerprint templates in batches, see descriptions of batch process function.
6.16 Differences between High-speed Upload and Ordinary Upload
In an ordinary upload, each time upload functions (such as SSR_SetUserinfo and
SSR_SetUserTmpStr) are used, the SDK communicates with the device and uploads related data
to the device.
In a high-speed upload, BeginBatchUpdata is used to create a temporary buffer to store the data
to be uploaded in subsequent operations. Then, BatchUpdata can be used to upload all the data in
the buffer to the device at a time. This mode greatly reduces communications between the SDK
250
and the device, and raises the speed of large-capacity upload in particular.
Note
BW device use SetUserinfo instead of SSR_SetUserinfo, SetUserTmpStr instead of
SSR_SetUserTmpStr.
6.17 How to Determine Whether the Device Uses ZKFinger10.0 or
ZKFinger9.0?
Use the following function:
VARIANT_BOOL GetSysOption([in] LONG dwMachineNumber, [in] BSTR Option, [out]
BSTR* Value)
The Option parameter constantly "~ZKFPVersion". If the returned Value is 10, the device uses
ZKFinger10.0. If the returned Value is 9 or null (null is returned as old TFT devices do not have
this value), the device uses ZKFinger9.0.
For example:
zkem.GetSysOption(EmManth.EmMan.Dev.MachineNumber,'~ZKFPVersion',verSionFp);
If verSionFp='10', the device uses ZKFinger10.0
If verSionFp=‘9’ or verSionFp=‘’, the device uses ZKFinger9.0
6.18 How to Upload, Download, and Delete ZKFinger10.0 Templates?
ZKFinger10.0 provides faster comparison, but the template size and storage mode are different
from those of older versions:
When ZKFinger10.0 is used, the size of a fingerprint template is about 1.6 KB. When an older
version is used, the size of a fingerprint template is smaller than 608B.
You can use follow function to upload,download and delete ZKFinger10.0 Templates:
VARIANT_BOOL SetUserTmpEx([in] LONG dwMachineNumber, [in] BSTR dwEnrollNumber,
[in] LONG dwFingerIndex,[in] LONG Flag, [in] BYTE* TmpData)
VARIANT_BOOL GetUserTmpEx([in] LONG dwMachineNumber, [in] BSTR
dwEnrollNumber, [in] LONG dwFingerIndex,[out] LONG * Flag, [out] BYTE* TmpData, [out]
LONG* TmpLength)
VARIANT_BOOL SetUserTmpExStr([in] LONG dwMachineNumber, [in] BSTR
dwEnrollNumber, [in] LONG dwFingerIndex,[in] LONG Flag, [in] BSTR TmpData)
VARIANT_BOOL GetUserTmpExStr([in] LONG dwMachineNumber, [in] BSTR
dwEnrollNumber, [in] LONG dwFingerIndex,[out] LONG * Flag, [out] BSTR* TmpData, [out]
LONG* TmpLength)
The above four functions can upload and download both ordinary fingerprint templates (Flag=1)
and threatened fingerprint templates (Flag=3). Additionally, they can be used for both
ZKFinger10.0 templates and ZKFinger9.0 templates.
To delete ZKFinger10.0 templates, you can use the following functions (these two functions are
251
used on TFT devices to delete fingerprint templates):
VARIANT_BOOL SSR_DelUserTmp([in] LONG dwMachineNumber, [in] BSTR EnrollNumber,
[in]LONG dwFingerIndex)
VARIANT_BOOL SSR_DelUserTmpExt([in] LONG dwMachineNumber, [in] BSTR
dwEnrollNumber, [in]LONG dwFingerIndex)
Note:
Ver6.60 is the internal version of device firmware. You can obtain it by using
GetFirmwareVersion after SDK connects to the device (or by using the attendance software).
Caution: The internal version obtained is different from the firmware version that you view on
the device.
6.19 How to Upload, Download, and Delete ZKFinger9.0 Templates?
The functions used to upload and download ordinary ZKFinger9.0 templates (that is,
SSR_GetUserTmp, SSR_GetUserTmpStr, SSR_SetUserTmp, and SSR_SetUserTmpStr) in
earlier SDK versions are continuously used in the present SDK version.
New functions (that is, SetUserTmpEx, GetUserTmpEx, SetUserTmpExStr, and
GetUserTmpExStr) are also added in the present SDK version. These functions can upload and
download both ordinary fingerprint templates (Flag=1) and threatened fingerprint templates
(Flag=3). But they are used only on the TFT devices with firmware Ver6.60 or later. Additionally,
they can be used for both ZKFinger10.0 templates and ZKFinger9.0 templates.
To delete ZKFinger9.0 templates, you can use SSR_DelUserTmp or SSR_DelUserTmpExt.
6.20 How to Download a Face Template?
1. The transmission mode of face templates is the same as that of ZKFinger10.0 fingerprint
templates.
2. One user has about 15 face templates in different angles. Each template consists of 2576 bytes.
The third and fourth bytes of each template indicate the ID, corresponding to the first and second
bytes of user structure. For devices that support face identification, the last 24 bytes of user
structure indicate the user ID. Therefore, the total size of face templates of each user is about 37
KB. You are not recommended to upload or download data via serial ports. When the value of
dwFaceIndex is 50, all face templates of a user are uploaded or downloaded.
3. To upload and download ZKFace templates, use the following functions:
SetUserFace(LONG dwMachineNumber, BSTR dwEnrollNumber, LONG dwFaceIndex, BYTE*
TmpData, LONG TmpLength, VARIANT_BOOL* pVal);
GetUserFace(LONG dwMachineNumber, BSTR dwEnrollNumber, LONG dwFaceIndex,
BYTE* TmpData, LONG * TmpLength, VARIANT_BOOL* pVal);
DelUserFace (LONG dwMachineNumber, BSTR dwEnrollNumber, LONG dwFaceIndex,
VARIANT_BOOL* pVal);
For details, see description of the functions.
252
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 264 Language : zh-CN Tagged PDF : Yes Author : PC Creator : Microsoft® Word 2010 Create Date : 2018:05:08 09:02:40+08:00 Modify Date : 2018:05:08 09:02:40+08:00 Producer : Microsoft® Word 2010EXIF Metadata provided by EXIF.tools