MB308 MPI Maruti 800 Owners Manual Petrol

User Manual:

Open the PDF directly: View PDF .
Page Count: 100

Download
Open PDF In Browser	View PDF

60G-79F-844-A

8 PAGES BALENO, WAGONR, MARUTI 800 (MPI)

TABLE OF CONTENTS

MAINTENANCE SERVICE RECORD

WARRANTY POLICY

BEFORE DRIVING

STEERING COLUMN CONTROLS

INSTRUMENT PANEL

OTHER CONTROLS AND EQUIPMENT

OPERATING YOUR VEHICLE

DRIVING TIPS AND SAFE DRIVING

INSPECTION AND MAINTENANCE

EMERGENCY SERVICE

BODY WORK CARE

GENERAL INFORMATION

SPECIFICATIONS

SERVICE NETWORK

8 PAGES BALENO, WAGONR, MARUTI 800 (MPI)

60G-79F-844-A

FOREWORD
This manual is an essential part of your
vehicle and should be kept with the vehicle
at all times. Please read this manual
carefully and review it from time to time. It
contains important information on safety,
operation, and maintenance. It is especially
important that this manual remain with the
vehicle at the time of resale. The next
owner will need this information also.

8 PAGES BALENO, WAGONR, MARUTI 800 (MPI)

You are invited to avail the three free
inspection services as described in this
manual. Three free inspection coupons are
attached to this manual. Please show this
manual to your dealer when you take your
vehicle for any Service.
To prolong the life of your vehicle and
reduce maintenance costs, the periodic
maintenance must be carried out according
to the "PERIODIC MAINTENANCE
SCHEDULE" described in “INSPECTION
AND MAINTENANCE” section of this
manual. Periodic maintenance is essential
for preventing trouble and accidents to
ensure your satisfaction and safety.
Daily Inspection and Care as per "DAILY
INSPECTION CHECKLIST" described in the
"INSPECTION AND MAINTENANCE"
section of this Manual is essential for
prolonging the operating life of the vehicle
and for safe driving.
3

IMPORTANT
MARUTI UDYOG LIMITED believes in
conservation and protection of Earth’s
natural resources.
To that end, we encourage every vehicle
owner to recycle, trade in, or properly
dispose of, as appropriate, used motor oil,
coolant, and other fluids; batteries; and
tyres.

MARUTI UDYOG LIMITED
All information in this manual is
based on the latest product
information available at the time of
publication. Due to improvements or
other changes, there may be
discrepancies between information in
this manual and your vehicle. Maruti
reserves the right to make changes
at any time without notice.
This vehicle may not comply with
standards or regulations of other
countries. Before attempting to
register this vehicle in any other
country, check all applicable
regulations and make any necessary
modifications.

WARNING/CAUTION/NOTE
Please read this manual and follow its
instructions carefully. To emphasise special
information, the words WARNING,
CAUTION, and NOTE have special
meanings. Information following these signal
words should be carefully reviewed.

w WARNING
The personal safety of the driver,
passengers, or bystanders may be
involved. Disregarding this information
could result in their injury or death.

w CAUTION
These instructions point out special
service procedures or precautions that
must be followed to avoid damaging
the vehicle.

NOTE:
This provides special information to make
maintenance easier or important instructions
clearer.

0-1

60G-79F-844-A

MODIFICATION WARNING

8 PAGES BALENO, WAGONR, MARUTI 800 (MPI)

60G-00-004

The circle with a slash in this manual
means "Don't do this" or "Don't let this
happen".

w WARNING

w CAUTION

Do not modify this vehicle.
Modification could adversely affect
safety, handling, performance, or
durability and may contravene
regulations. In addition, damage or
performance problems resulting from
modification may not be covered
under warranty.

Improper installation of mobile
communication equipment such as
cellular telephones or CB (Citizen’s
Band) radios may cause electronic
interference with your vehicle’s
ignition system, resulting in vehicle
performance problems. Consult your
MARUTI dealer or qualified service
technician for advice on installing
such
mobile
communication
equipment.

w WARNING
Your vehicle has monocoque body
construction which provides for
certain crumple zones in the body
which absorbs larger part of impact
energy in the event of a front collision
and protects the occupants from
impact. Do not use any fitments such
as crash guards. These fitments will
increase the risk to the occupants
because of the shock directly getting
transmitted to the occupants.

Copying, quoting or reproduction of any part
of this manual is not permitted without
explicit approval by MARUTI UDYOG
LIMITED.

0-2

MAINTENANCE SERVICE RECORD

60G-79F-844-A

MAINTENANCE SERVICE RECORD
MODEL

CHASSIS NO.

ENGINE NO.

1
DATE OF
DELIVERY

MILEAGE

MAKE

BATTERY
SR. NO/BATCH CODE

km.

OWNER'S NAME & ADDRESS ______________________________________________________________________________

______________________________________________________________________________TEL. NO. ________________

ADDRESS/STAMP OF SELLING DEALER

SELLING DEALER CODE

8 PAGES BALENO, WAGONR, MARUTI 800 (MPI)

SHOWROOM

IMPORTANT INFORMATION TO CUSTOMER

WORKSHOP

Dear Customer
For any assistance with regard to our product, please
contact General Manager/Works Manager at any of
our Dealer or Authorised Service Station. For
additional enquiry you may contact our Regional
office or Service Department. The Addresses and
Phone nos. are given in Section 14 of this Booklet.
1-1

MAINTENANCE SERVICE RECORD

8 PAGES BALENO, WAGONR, MARUTI 800 (MPI)

DATE OF
SERVICE

F....free Service

1-2

KIND OF
SERVICE

MILEAGE
km

P....Paid Service W....Warranty.

60G-79F-844-A

DESCRIPTION OF JOB

NAME OF SERVICING
DEALER/MASS

JOB CARD
NO.

MECHANIC’S
SIGNATURE

A....Accident
6

WARRANTY POLICY

60G-79F-844-A

WARRANTY POLICY
Maruti Udyog Limited (hereinafter called “Maruti”), warrants that each
new Maruti vehicle distributed in India by Maruti and sold by an
authorised Maruti dealer will be free, under normal use and service,
from any defects in material and workmanship at the time of
manufacture SUBJECT TO THE FOLLOWING TERMS AND
CONDITIONS:
(1) Qualification:
To qualify for this warranty:
(a) The Maruti vehicle must be delivered by Maruti authorised
dealer and set-up, serviced by Maruti authorised dealer/
service station.

8 PAGES BALENO, WAGONR, MARUTI 800 (MPI)

(b) The warranty registration card in respect of each vehicle
must be completed by the dealer at the time of delivery of
the vehicle and dealer should retain the same.
(2) Term:
The term of the warranty shall be twenty four (24) months
or 40,000 kilometers (whichever occurs earlier) from the date
of delivery to the first owner.
(3) Maruti’s Warranty Obligation:
If any defect(s) should be found in a Maruti vehicle within the
term stipulated above, Maruti’s only obligation is to repair or
replace at its sole discretion any part shown to be defective,
with a new part or the equivalent at no cost to the owner for
parts or labour, when Maruti acknowledges that such a defect
is attributable to faulty material or workmanship at the time of
manufacture. The owner is responsible for any repair or
7

replacements which are not covered by this warranty.

(4) Limitation:
This warranty shall not apply to:
(a) normal maintenance service required other than the three free
services, including without limitation, oil and fluid changes,
headlight aiming, fastener retightening, wheel balancing, wheel
alignment and tyre rotation, cleaning of injectors, adjustments
of carburettor, ignition timing, clutch and valve clearance.
(b) the replacement of normal wear parts including without
limitation, bulbs, battery, tyres and tubes, spark plugs, brake
linings, belts, hoses, filters, wiper blades and brushes, contact
points, fuses, clutch disc, brake pads, brake shoes, cables
and all rubber parts (except oil seals and glass run).
(c) any vehicle which has been used for competition or racing.
(d) any repairs or replacement required as a result of accidents
or collision.
(e) any defects caused by misuse, negligence, abnormal use or
insufficient care.
(f) any vehicle which has been modified or altered, including
without limitation, the installation of performance accessories.
(g) any vehicle on which parts or accessories not approved by
Maruti have been used.
(h) any vehicle which has not been operated in accordance with
the operating instructions in the Maruti Owner’s Manual.
(i) any vehicle which has not received, during the warranty term,
the service inspections prescribed in the Maruti Owner’s
Manual.

2-1

WARRANTY POLICY

(j) any vehicle which has been assembled, disassembled,
adjusted or repaired by other than an Maruti authorised
dealer/service station.
(k) any vehicle which has been used for purposes other than
what it was designed for.
(l) any damage or deterioration caused by industrial pollution
and bird droppings.
(m) insignificant defects which do not affect the function of the
vehicle including without limitation, sound, vibration and fluid
seep.
(n) any natural wear and tear including without limitation, aging
etc.
For Maruti Air-Conditioned Vehicles
8 PAGES BALENO, WAGONR, MARUTI 800 (MPI)

(o) V-belts, hoses and gas leaks.
(5) Extent of Warranty:
This warranty is the entire written warranty given by Maruti for
Maruti vehicles and no dealer or its or his agent or employee
is authorised to extend or enlarge this warranty and no dealer
or its or his agent or employee is authorised to make any oral
warranty on Maruti’s behalf.
Maruti reserves the right to add any improvements or change
the design of any model at any time with no obligation to make
the same changes on units previously sold.
(6) Warranty Service:
To obtain warranty service, the complete vehicle must be
presented at the owner’s expenses to any authorised Maruti
dealer.

2-2

60G-79F-844-A

(7) Owner’s Warranty Responsibilities:
It is responsibility of each owner to:
(a) make certain that the warranty registration/PDI card was
completed at the time of delivery of the vehicle;
(b) have performed, at his own expenses, by an Maruti
authorised dealer/service station all the service inspections
specified in the Maruti “Owner’s Manual and Service Booklet”
and maintain adequate proof that such service inspections
have been performed.
(c) make certain that the Maruti authorised dealer/service station
performing the service inspection has certified the work on
the “Maintenance Service Record” page in the “Owner’s
Manual and Service Booklet” and
(d) present the Maruti “Owner’s Manual and Service Booklet” to
the authorised Maruti dealer whenever requesting service
inspections or warranty service.
If the “Owner’s Manual and Service Booklet” should be lost or
destroyed the owner should consult the authorised Maruti dealer
from whom the vehicle was purchased for instructions concerning
replacement of the “Owner’s Manual and Service Booklet”.
(8) Disclaimer of Consequential Damage:
Maruti assumes no responsibility for loss of vehicle, loss of time,,
inconvenience or any other indirect incidental or consequential
damage resulting from the vehicle not being available to the
owner because of any defect covered by this warranty.
(9) Change of Owner
Even if ownership of the vehicle changes, the remaining warranty
8
period is effective for the new owner.

844-74E-I

BEFORE DRIVING

BEFORE DRIVING
Fuel Recommendation ....................................................................................... 3-1
Keys ...................................................................................................................... 3-2
Door Locks .......................................................................................................... 3-2
Windows ............................................................................................................... 3-4
Mirrors ................................................................................................................... 3-4
Front Seat Adjustment ...................................................................................... 3-5
Adjustable Head Restraints (if equipped) ..................................................... 3-6
Seat Belts ............................................................................................................ 3-6

BEFORE DRIVING

844-74E-I

FUEL RECOMMENDATION

w CAUTION
Use of leaded fuel in vehicle equipped
with catalytic converter is prohibited,
because lead deactivates the pollutant
reducing components of catalytic
converter and may result in permanent
damage to catalytic converter.
Petrol/Ethanol Blends
Blends of unleaded petrol and ethanol (grain
alcohol), also known as gasohol, are
commercially available in some areas.
Blends of this type may be used in your
vehicle if they are no more than 10%
ethanol. Make sure this petrol-ethanol blend
has octane ratings no lower than those
recommended for petrol.
Petrol/Methanol Blends
Blends of unleaded petrol and methanol
(wood alcohol) are also commercially
available in some areas. DO NOT USE
fuels containing more than 5% methanol
under any circumstances. Fuel system
damage or vehicle performance problems
resulting from the use of such fuels are not
the responsibility of MARUTI and may not
be covered under Warranty.

3-1

Fuels containing 5% or less methanol may
be suitable for use in your vehicle if they
contain cosolvents and corrosion inhibitors.

NOTE:
If you are not satisfied with the driveability
or fuel economy of your vehicle when you
are using a petrol/alcohol blend, you should
switch back to unleaded petrol containing no
alcohol.

w CAUTION
Be careful not to spill fuel containing
alcohol while refuelling. Fuels
containing alcohol can cause paint
damage, which is not covered under
Warranty.

w CAUTION
The fuel tank has an air space to
allow for fuel expansion in hot
weather. If you continue to add fuel
after the filler nozzle has automatically
shut off or an initial blowback occurs,
the air chamber will become full.
Exposure to heat when fully fuelled in
this manner will result in leakage due
to fuel expansion. To prevent such
fuel leakage, stop filling after the filler
nozzle has automatically shut off, or
when using an alternative non
automatic system, initial vent
blowback occurs.

BEFORE DRIVING

844-74E-I

KEYS

DOOR LOCKS

843-03-003

Your vehicle comes with a pair of identical
keys. Keep the spare key in a safe place.
One key can open all of the locks on the
vehicle.
The key identification number is stamped on
a metal tag provided with the keys. Keep
the tag in a safe place. If you lose your
keys, you will need this number to have
new keys made. Write the number down
and keep it in a safe accessible place away
from the vehicle.

843-03-004E

• Do not use locally made key.
• Should you require a duplicate key,
place your order with a MARUTI
dealer only.

To lock a front door from outside the
vehicle:
a) Insert the key fully and turn the top of
the key toward the front of the vehicle,
or
b) Push in the lock lever and hold the door
handle up as you close the door.

Note:
Keep the spare key very carefully. When it
is lost, consult your dealer by quoting key
number.

To unlock a front door from outside the
vehicle, insert the key fully and turn the top
of the key toward the rear of the vehicle.

w WARNING

To lock a rear door from outside the vehicle,
push in the lock lever and close the door.

3-2

BEFORE DRIVING

844-74E-I

843-03-005E

843-03-006E

To lock a door from inside the vehicle, push
in the lock lever. Pull out the lock lever to
unlock the door.

Hatchback
To unlock insert the key fully in to the lock
knob and turn it anticlockwise and to lock
turn it clockwise. Hatchback can be opened
by pushing in the lock knob and lifting hookshaped grip.

w WARNING
Always lock all doors when driving.
Locking the door prevents occupants
from being thrown from the vehicle in
the event of an accident. It also helps
prevent unintentional opening of the
doors.

3-3

w CAUTION
Do not use the key to lift up the lid,
or the key may break off in the lock.

w WARNING
Always make sure that the hatchback
is closed and latched securely.
Completely closing it helps keep
exhaust gases from entering the car.
Completely closing the hatchback lid
also helps prevent occupants from
being thrown from the vehicle in the
event of an accident.
12

BEFORE DRIVING

844-74E-I

WINDOWS

MIRRORS

70F-01-010

70F-01-013

72F-03-005

Raise or lower the door windows by turning
the handle located on the door panel.

Inside Rearview Mirror
To adjust the interior rearview mirror, move
the mirror up, down, or sideways to obtain
the best view.

Outside Rearview Mirror
Adjust the outside rearview mirror so you
can just see the side of your vehicle in the
mirror.

w WARNING
Be careful when judging the size or
distance of a vehicle or other object
seen in the side convex mirror (if
equipped). Be aware that objects look
smaller and appear farther away than
when seen in a flat mirror.

3-4

BEFORE DRIVING

844-74E-I

FRONT SEAT ADJUSTMENT

w WARNING
Never attempt to adjust the driver’s
seat or seatback while driving. The
seat or seatback could move
unexpectedly, causing loss of control.
Make sure that the driver’s seat and
seatback are properly adjusted before
you start driving.

843-03-008

843-03-010

Adjusting Seat Position
The adjustment lever for each front seat is
located under the front of the seat, on the
inboard side. To adjust the seat position,
pull up on the adjustment lever and slide
the seat forward or rearward. After
adjustment, try to move the seat forward
and rearward to ensure that it is securely
latched.

Adjusting Seatbacks
The seatbacks can be adjusted to different
angles. To adjust the seatback angle, pull
up the lever on the outboard side of the
seat, move the seatback to the desired
position, and release the lever to lock the
seatback in place.

w WARNING

Seatbacks should always be in an
upright position when driving, or seat
belt effectiveness may be reduced.
Seat belts are designed to offer
maximum protection when seatbacks
are in the fully upright position.

To avoid excessive seat belt slack,
which reduces the effectiveness of the
seat belts as a safety device, make
sure that the seats are adjusted before
the seat belts are fastened.

3-5

w WARNING

BEFORE DRIVING

844-74E-I

ADJUSTABLE HEAD RESTRAINTS
(if equipped)

70F-01-019

w WARNING
• Never drive the vehicle with the
head restraints removed.
• Do not attempt to adjust the head
restraint while driving.
Head restraints are designed to help reduce
the risk of neck injuries in the case of an
accident. Adjust the head restraint to the
position which places the top of the head
restraint closest to the top or your ears.

SEAT BELTS

70F-01-021

843-03-012

There are two height positions for the head
restraints. To raise the head restraint, pull
upward on the restraint until it clicks. To
lower the restraint, push down on the
restraint while holding in the lock lever. If
a head restraint must be removed (for
cleaning, replacement, etc.), push in the lock
lever and pull the head restraint all the way
out.

w WARNING
Wear Your Seat Belts at All Times.
There are two types of seat belt "Automatic
retracting type" and "3-point, non retractor
type".
The type of belts provided in your vehicle
depends on the vehicle specification.
To fasten the seat belt, pull the buckle
tongue attached to the seat belt across your
body and slide it into the buckle catch slot
on the opposite side until you hear a “click”.

3-6

BEFORE DRIVING

844-74E-I

70F-01-022E

70F-01-023E

To reduce the risk of sliding under the belt
during a collision, position the lap portion of
the belt across your lap as low on your hips
as possible and adjust the belt to a snug
fit using the proper method described below.
Make sure that the belt is not twisted.

To unfasten the belt, press the release
button on the buckle catch.

70F-01-024E

To Adjust the Belt
•

Automatic retracting type
Pull the shoulder portion of the belt
upwards through the tongue plate.

The length of the diagonal shoulder strap
adjusts itself to allow freedom of movement.
The seat belt has an emergency locking
retractor (ELR), which is designed to lock
the seat belt only during a sudden stop or
impact.

w WARNING
No modifications or additions of any
sort should be made to the seat belt
or its operating mechanism.

3-7

BEFORE DRIVING

844-74E-I

•

843E-01-003E

843E-01-004E

3-point non-retractor type
Adjust the shoulder portion of the belt so
that it is slightly slack. To shorten the
belt, pull the free end in the direction of
the arrow as illustrated. To lengthen the
belt, grab it at the shoulder anchor and
pull it in the direction of the arrow, at
right angles to the anchor. The shoulder
portion should have just enough slack so
that a clenched fist can be inserted
between the belt and your chest as
illustrated. Too much slack at the
shoulder portion makes the belt
ineffective in accidents. The shoulder
portion should be worn on the outside
shoulder only, and never under the arm.

After use, always rehang the belt on the
hook provided near the upper anchorage
point.

843E-01-005

w WARNING
• Inspect all seat belts after any
collision. Any automatic retracting
type belt which was in use at the
time of collision and subjected to
stress must be replaced.
• Any automatic retracting type belt
not in use at the time of collision
should be carefully inspected and
the static operation checked. If there
is any doubt whatsoever in the
operation or condition of the belt, it
must be replaced.
• Non retractor type belts with any
form of damage or abrasion to any
part of the belt must be replaced.

3-8

BEFORE DRIVING

844-74E-I

w WARNING

• Never allow persons to ride in the
cargo area of a vehicle. In the event
of an accident, there is a much
greater risk of injury for persons
who are not riding in a seat with
their seat belt securely fastened.
• Seat belts should always be
adjusted so the lap portion of the
belt is worn low across the pelvis,
not across the waist. Shoulder
straps should be worn on the
outside shoulder only, and never
under the arm. Seat belts should
never be worn with the straps
twisted and should be adjusted as
tightly as is comfortable to provide
the protection for which they have
been designed. A slack belt will
provide less protection than one
which is snug.
• Make sure that each seat belt buckle
is inserted into the proper buckle
catch.
• Do not wear your seat belt over
hard or breakable objects in your

pockets or on your clothing. If an
accident occurs, objects such as
glasses, pens, etc. under the seat
belt can cause injury.
• Never use the same seat belt on
more than one occupant and never
attach a seat belt over an infant or
child being held on an occupant’s
lap. Such seat belt use could cause
serious injury in the event of an
accident.
• Pregnant women should use seat
belts, although specific recommendations about restraint use should
be made by the woman’s medical
advisor.
• Periodically inspect seat belt
assemblies for excessive wear and
damage. Seat belts should be
replaced if webbing becomes frayed,
contaminated, or damaged in any
way. It is essential to replace the
entire seat belt assembly after it has
been stressed in an impact, even if
damage to the assembly is not
obvious.

3-9

w WARNING
• Infants and small children should
never be transported unless they
are properly restrained. Restraint
systems for infants and small
children can be purchased locally
and should be used. Make sure that
the system you purchase meets
applicable safety standards. Read
and follow all the directions
provided by the manufacturer.
• Avoid contamination of seat belt
webbing
by
polishes,
oils,
chemicals, and particularly battery
acid. Cleaning may safely be carried
out using mild soap and water.
• For children, if the shoulder belt
irritates the neck or face, move the
child closer to the center of the
vehicle.

w WARNING

STEERING COLUMN CONTROLS

844-74E-I

STEERING COLUMN CONTROLS
Ignition Switch .................................................................................................... 4-1
Lighting/Turn Signal Control Lever ................................................................ 4-2
Hazard Warning Switch..................................................................................... 4-3
Windscreen Wiper and Washer Lever ........................................................... 4-4
Horn ....................................................................................................................... 4-5

STEERING COLUMN CONTROLS

844-74E-I

IGNITION SWITCH

60G-04-001E

w WARNING
To avoid possible injury, do not
operate controls by reaching through
the steering wheel.

70F-02-002

70F-02-003E

The ignition switch has the following four
positions:

LOCK
This is the normal parking position. It is the
only position in which the key can be
removed.

w WARNING
• Do not use any locally made key.
• Should you require duplicate key,
place your order with MARUTI
dealer only.

The “LOCK” position locks the ignition, and
prevents normal use of the steering wheel
after the key is removed.
To release the steering lock, fully insert the
key and turn it clockwise to one of the other
positions. If you have trouble turning the
key to unlock the steering, try turning the
steering wheel slightly to the right or left
while turning the key.

4-1

STEERING COLUMN CONTROLS

844-74E-I

LIGHTING/TURN SIGNAL
CONTROL LEVER
ACC
Accessories such as the radio can operate,
but the engine is off.
ON
This is the normal operating position. All
electrical systems are on.
START
This is the position for starting the engine
using the starter motor. The key should be
released from this position as soon as the
engine starts.

w WARNING
• Never remove the ignition key while
the vehicle is moving. The steering
wheel will lock and you will not be
able to steer the vehicle.
• Do not leave children alone in a
parked vehicle. Unattended children
could cause accidental movement of
the vehicle, which could result in
severe personal injury.
• Always remove the key when parked
to prevent unintentional operation of
the vehicle and to improve security.

w CAUTION
• Do not use the starter motor for
more than 15 seconds at a time. If
the engine does not start; wait 15
seconds before trying again. If the
engine does not start after several
attempts, check the fuel and ignition
systems or consult your MARUTI
dealer.
• Do not leave the ignition switch in
the “ON” position if the engine is
not running as the battery will
discharge.

843-04-003

This control lever is located on the outboard
side of the steering column. Operate the
lever as described below.
Lighting Operation
To turn the lights on or off, twist the knob
on the end of the lever. There are three
positions: in the “OFF” position all lights are
off; in the middle position the front parking
lights, tail-lights, registration plate light, and
instrument lights are on, but the headlights
are off; in the third position the headlights
come on in addition to the other lights.

4-2

STEERING COLUMN CONTROLS

844-74E-I

HAZARD WARNING SWITCH

843-04-004E

843-04-005

843-04-007

With the headlights on, push the lever
forward to switch to the high beams (main
beams) or pull the lever toward you to
switch to the low beams. When the high
beams (main beams) are on, a light on the
instrument panel will come on. To flash the
high beams (main beams) pull the lever
slightly towards you and release it.

Turn Signal Operation
With the ignition switch in the “ON” position,
move the lever clockwise until it clicks to
signal a right turn or anticlockwise to signal
a left turn. When the turn is completed, the
signal will cancel and the lever will return
to its normal position.

Pull up the hazard warning switch to
activate the hazard warning lights. All four
turn signal lights and both turn signal
indicators will flash simultaneously. To turn
off the lights, push down switch.

4-3

Use the hazard warning lights to warn other
traffic during emergency parking or when
your vehicle could otherwise become a
traffic hazard.

STEERING COLUMN CONTROLS

844-74E-I

WINDSCREEN WIPER AND
WASHER LEVER
Windscreen Washer
To spray windscreen washer fluid, pull the
lever toward you. The windscreen wipers will
automatically turn on at low speed if they
are not already on and the “INT” position
is equipped.

w WARNING

843-04-008E

Windscreen Wipers
To turn the windscreen wipers on, twist the
knob on the end of the lever to one of the
three operating positions. In the “INT”
position (if equipped), the wipers operate
intermittently. The “INT” position is very
convenient for driving in mist or light rain.
In the “LO” position, the wipers operate at
a steady low speed. In the “HI” position, the
wipers operate at a steady high speed. To
turn off the wipers, move the lever back to
the “OFF” position.

• To prevent windscreen icing in cold
weather, turn on the defroster to
heat the windscreen before and
during windscreen washer use.
• Do not use radiator antifreeze in the
windscreen washer reservoir. It can
severely impair visibility when
sprayed on the windscreen, and can
also damage your vehicle’s paint.

w CAUTION
To help prevent damage to the
windscreen wiper and washer system
components, you should take the
following precautions:
• Do not continue to hold in the lever
when there is no windscreen washer
fluid being sprayed or the washer
motor can be damaged.
• Do not attempt to remove dirt from
a dry windscreen with the wipers or
you can damage the windscreen and
the wiper blades. Always wet the
windscreen with washer fluid before
operating the wipers.
• Clear ice or packed snow from the
wiper blades before using the
wipers.
• Check the washer fluid level
regularly. Check it often when the
weather is bad.
• Only fill the washer fluid reservoir
3/4 full during cold weather to allow
room for expansion if the
temperature falls low enough to
freeze the solution.

4-4

STEERING COLUMN CONTROLS

844-74E-I

HORN

72F-04-006

Press the center piece of the steering wheel
to sound the horn. The horn will sound with
the ignition switch in any position.

4-5

844-74E-I

INSTRUMENT PANEL

INSTRUMENT PANEL
Instrument Panel ................................................................................................ 5-1
Instrument Cluster .............................................................................................. 5-1
Warning and Indicator Lights .......................................................................... 5-2
Speedometer/Odometer ...................................................................................... 5-4
Fuel Gauge .......................................................................................................... 5-4
Temperature Gauge ............................................................................................ 5-5
Ashtray .................................................................................................................. 5-5
Glove Box ............................................................................................................ 5-6
Heating System (if equipped) .......................................................................... 5-7
System Operating Instructions ........................................................................ 5-8
Air Conditioning System (if equipped) ....................................................... 5-11
System Operating Instructions ...................................................................... 5-11

INSTRUMENT PANEL

844-74E-I

1. Instrument cluster
2. Ignition switch
3. Lighting switch/Turn signal and
dimmer switch
4. Windscreen wiper and washer
switch
5. Hazard warning switch
6. Other switches (if equipped)
7. Heater control panel
8. Cigarette lighter (if equipped)
9. Ashtray
10. Bonnet release
11. Center ventilator
12. Side ventilator
13. Side defroster
14. Glove box
15. Fuse box

INSTRUMENT PANEL

INSTRUMENT CLUSTER

843-05-042

1
2
3
4
5

5-1

Speedometer
Odometer
Fuel gauge
Temperature gauge
Warning and indicator lights

843-05-043
26

INSTRUMENT PANEL

844-74E-I

WARNING AND INDICATOR LIGHTS

70F-07-070

Brake fluid level warning light
This light operates under two conditions: 1)
when the ignition switch is turned to the
“ON” position, or 2) when the fluid in the
brake fluid reservoir falls below the specified
level. The light should go out after starting
the engine. If the light does not go off or
comes on whilst you are driving, it may
mean that there is something wrong with the
vehicle’s braking system. If this happens,
you should:
1) Pull off the road and stop carefully.

w WARNING
Remember that stopping distance may
be longer, you may have to push
harder on the pedal, and the pedal
may go down farther than normal.

2) Test the brakes by carefully starting and
stopping at the side of the road.
3) If you determine that it is safe, drive
carefully at low speed to the nearest
dealer for repairs.
or
4) Have the vehicle towed to the nearest
dealer for repairs.

w WARNING
If any of the following conditions
occur, you should immediately ask
your MARUTI dealer to inspect the
brake system.
• If the brake fluid level warning light
does not go out after the engine
has been started.
• If the brake fluid level warning light
does not come on when the ignition
switch is turned to the “ON”
position.
• If the brake fluid level warning light
comes on at any time during vehicle
operation.

NOTE:
Because the disc brake system is self
adjusting, the fluid level will drop as the
brake pads become worn.
Replenishing the brake fluid reservoir is
considered normal periodic maintenance.

843-05-041

Parking brake indicator light
This light comes on when the parking brake
is not fully released and the ignition switch
is in the “ON” position.

70F-03-039

Oil Pressure Light
This light comes on when the ignition switch
is turned on, and goes out when the engine
is started. The light will come on and remain
on if there is insufficient oil pressure. If the
light comes on when driving, pull off the
road as soon as you can and stop the
engine. Check the oil level and add oil if
necessary (see pages 9-7 and 9-8). If there
is enough oil, the lubrication system should
be inspected by your MARUTI dealer before
you drive the vehicle again.

5-2

INSTRUMENT PANEL

844-74E-I

72F-05-027

70F-03-009

70F-03-008E

w CAUTION
• If you operate the engine with this
light on, severe engine damage can
result.
• Do not rely on the Oil Pressure
Light to indicate the need to add oil.
Be sure to periodically check the
engine oil level (see pages 9-7 and
9-8).

Charging Light
This light comes on when the ignition switch
is turned on, and goes out when the engine
is started. The light will come on and remain
on if there is something wrong with the
battery charging system. If the light comes
on when the engine is running, the charging
system should be inspected immediately by
your MARUTI dealer.

w CAUTION
Do not continue driving long with the
charging light ON as this will drain the
battery 'dead'.

5-3

“Malfunction Indicator” Light
Your vehicle has a computer-controlled
emission control system. A “Malfunction
Indicator” light is provided on the instrument
panel to indicate when it is necessary to
have the emission control system serviced.
The “Malfunction Indicator” light comes on
when the ignition switch is turned to “ON”
and goes out when the engine is started.
If the “Malfunction Indicator” light comes on
when the engine is running, there is a
problem with the emission control system.
Take the vehicle to your MARUTI dealer to
have the problem corrected.

w CAUTION
Continuing to drive the vehicle when
the “Malfunction Indicator” light is on
can cause permanent damage to the
vehicle’s emission control system, and
can affect fuel economy and
driveability.
28

INSTRUMENT PANEL

844-74E-I

SPEEDOMETER/ODOMETER

FUEL GAUGE

70F-03-042

Turn Signal Indicators
When you turn on the left or right turn
signals, the corresponding green arrow on
the instrument panel will flash along with the
respective turn signal lights. When you turn
on the hazard warning switch, both arrows
will flash along with all of the turn signal
lights.

843-05-006

1 Speedometer
2 Odometer
The speedometer indicates vehicle speed in
km/h. The odometer records the total
distance the vehicle has been driven.

w CAUTION
70F-03-043

Main Beam (High Beam) Indicator Light
This indicator comes on when headlight
main beams (high beams) are turned on.

Keep track of your odometer reading
and check the maintenance schedule
regularly for required services.
Increased wear or damage to certain
parts can result from failure to
perform required services at the
proper mileage intervals and your
warranty rights may be affected.

843-05-008

This gauge gives an approximate indication
of the amount of fuel in the fuel tank. “F”
stands for full and “E” stands for empty.

NOTE:
This vehicle has fuel gauge of new design.
Even when the ignition switch is “OFF”, the
needle will not return to “E” position but will
show the reading.

5-4

INSTRUMENT PANEL

844-74E-I

ASHTRAY

TEMPERATURE GAUGE

843-05-010E

70F-03-025E

843-05-011E

When the ignition switch is on, this gauge
indicates the engine coolant temperature.
Under normal driving conditions, the
indicator should stay within the normal,
acceptable temperature range between “H”
and “C”. If the indicator exceeds this range
and veers towards “H”, overheating is
indicated. Follow the instructions for engine
overheating
in
the
EMERGENCY
REMEDIES section.

Front
To remove the front panel ashtray for
cleaning, push down on the metal plate, and
pull the ashtray completely out of its holder.

Rear
The rear ashtray is fitted on the left rear
door.
To remove the rear ashtray, push down on
the tongue, and pull the ashtray out of its
holder.

w CAUTION

w WARNING
Make
sure
tobacco
is
fully
extinguished before closing the
ashtray. Never throw waste in the
ashtray: it could create a fire hazard.

Continuing to drive the vehicle when
engine overheating is indicated, can
result in severe engine damage.

5-5

INSTRUMENT PANEL

844-74E-I

GLOVE BOX

843-05-013

To open the glove box, pull the latch lever.
To close it, push the lid until it latches
securely.

w WARNING
Never drive with the glove box lid
open. It could cause injury if an
accident occurs.

5-6

INSTRUMENT PANEL

844-74E-I

HEATING SYSTEM (if equipped)
The heating system provides heating,
demisting, and ventilation.
a.
b.
c.
d.
e.

Windscreen defroster
Side defroster
Side outlet
Center outlet
Floor outlet

843-05-017

843-05-016

5-7

INSTRUMENT PANEL

844-74E-I

SYSTEM OPERATING INSTRUCTIONS
Description of Controls
Function selector 1: This selector is used
to select one of the functions described
below:

843-05-018

70F-03-029

70F-03-030

DEFROST & VENTILATION 2:
Temperature-controlled air comes
out of the center and side outlets
of instrument panel, windshield
defroster outlet and side air
outlets.
VENTILATION 3: Temperaturecontrolled air comes out of the
center and side air outlets.
BI-LEVEL 4 : Temperaturecontrolled air comes out of the
floor outlets and cooler air comes
out of the center and side outlets.
When the temperature control
lever is in the fully “COOL”
position or fully “HOT” position,
however, the air from the floor
outlets and the air from the center
and side outlets will be the same
temperature.

70F-03-032

70F-03-033

HEAT & DEFROST 6: Temperature-controlled air comes out of
the floor outlets, the windscreen
defroster outlets, and the side
defroster outlets.
DEFROST 7 : Temperaturecontrolled air comes out of the
windscreen defroster outlets and
the side defroster outlets.

Air Intake Lever 8: This lever is used to
select between circulating outside air
(FRESH AIR) or recirculating inside air
(RECIRCULATED AIR).
Temperature Control Dial 9: This dial is
used to control the temperature of the air
that comes out of the air outlets.
Fan switch 0: This switch is used to turn
on the fan and to select fan speed. There
are four positions: OFF, LOW, MEDIUM and
HIGH.

843-05-030E

Natural Ventilation
Move
the
function
selector
to
“VENTILATION”, the air intake lever to
“FRESH AIR”, The temperature control dial
to the desired temperature position, and the
fan switch to “OFF”. Fresh air will flow
through the vehicle when it is moving.

HEAT 5: Temperature-controlled
air comes out of the floor outlets.
70F-03-031

5-8

INSTRUMENT PANEL

844-74E-I

843-05-031E

843-05-032E

843-05-033E

Forced Ventilation
The lever settings are the same as for
natural ventilation except you move the fan
switch to a position other than “OFF”.

Normal Heating (Using outside air)
Move the function selector to “HEAT”, the
air intake lever to “FRESH AIR”, the
temperature control dial to the desired
temperature position, and the fan switch to
the desired fan speed position. Moving the
fan switch to a higher fan speed position
increases heating efficiency.

Quick Heating (Using recirculated air)
The lever settings are the same as for
normal heating except you move the air
intake lever to “RECIRCULATED AIR”. If
you use this heating method for an
extended period of time, the air in the
vehicle can become contaminated and the
windows can become misty. Therefore, use
this method only for quick heating and
change to the normal heating method as
soon as possible.

5-9

INSTRUMENT PANEL

844-74E-I

843-05-034E

843-05-035E

843-05-036E

Cool Face/Warm Feet
Move the function selector to “BI-LEVEL”,
the air intake lever to “FRESH AIR”, the
temperature control dial to the desired
temperature position, and the fan switch to
the desired fan speed position. Unless the
temperature control dial is in the fully
“COOL” position or fully “HOT” position, the
air that comes out of the center and side
outlets will be cooler than the air that comes
out of the floor outlets.

Defrosting/Warm Feet
Move the function selector to “DEFROST &
HEAT”, the air intake lever to “FRESH AIR”,
the temperature control dial to the desired
temperature position, and the fan switch to
“HIGH”. When the windscreen has become
clear, move the fan switch to the desired
fan speed position.

Defrosting
Move the function selector to “DEFROST”,
the air intake lever to “FRESH AIR”, the
temperature control dial to the desired
temperature position, and the fan switch to
“HIGH” Moving the temperature control dial
to a higher temperature position increases
defrosting efficiency. When the windscreen
has become clear, move the fan switch to
the desired fan speed position.

5-10

INSTRUMENT PANEL

844-74E-I

AIR CONDITIONING SYSTEM
(if equipped)

SYSTEM OPERATING INSTRUCTIONS

843-05-037

The air conditioning system can be used to
provide cooling and dehumidifying, as
described below. To turn on the air
conditioning system, push in the A/C button
and move the fan switch to a position other
than “OFF”. An indicator light will come on
when the air conditioning system is on. To
turn off the air conditioning system, push
the A/C button again.

5-11

843-05-038E

During operation of the air conditioner, you
may notice slight changes in engine speed.
These changes are normal, the system is
designed so that the compressor turns on
or off to maintain the desired temperature.
Less operation of the compressor results in
better fuel economy.

Normal Cooling (using outside air)
push in the A/C button, move the function
selector to “VENTILATION”, the air intake
lever to “FRESH AIR”, the temperature
control dial to the “COOL” position, and the
fan switch to the desired fan speed position.
Moving the fan switch to a higher fan speed
position increases cooling efficiency.

INSTRUMENT PANEL

844-74E-I

843-05-039E

843-05-040E

Quick Cooling (Using recirculated air)
The lever settings are the same as for
normal cooling except you move the air
intake lever to “RECIRCULATED AIR”. If
you use this cooling method for a extended
period of time, the air in the vehicle can
become contaminated. Therefore, you
should occasionally move the air intake
lever to “FRESH AIR”.

Dehumidifying
Push in the A/C button, move the function
selector to the desired function position, the
air intake lever to “FRESH AIR”, the
temperature control dial to the desired
temperature position, and the fan switch to
the desired fan speed position.

NOTE:
If your vehicle has been left in the sun with
the windows closed, it will cool faster if you
open the windows briefly while you operate
the air conditioner with the air intake lever
at “FRESH AIR” and the fan at high speed.

NOTE:
Because the air conditioner dehumidifies the
air, turning it on will help keep the windows
clear, even when blowing heated air using
the DEMIST or HEATER & DEMIST
functions.

5-12

844-74E-I

OTHER CONTROLS AND EQUIPMENT

844-74E-I

OTHER CONTROLS AND EQUIPMENT
Parking Brake Lever .......................................................................................... 6-1
Pedals ................................................................................................................... 6-2
Gear Lever ........................................................................................................... 6-3
Fuel Filler Cap .................................................................................................... 6-3
Folding Rear Seats ............................................................................................ 6-4
Sun Visor ............................................................................................................. 6-5
Interior Light Switch .......................................................................................... 6-5
Assist Grips ......................................................................................................... 6-6
Bonnet ................................................................................................................... 6-6
Tyre Changing Tools ......................................................................................... 6-7

OTHER CONTROLS AND EQUIPMENT

844-74E-I

PARKING BRAKE LEVER

w WARNING
Always apply the parking brake fully
before leaving your vehicle or it may
move, causing injury or damage.
When parking, make sure the gear
shift lever is left in first gear or
reverse. Remember, even though the
transmission is in gear, you must
always apply the parking brake fully.

70F-04-001E

The parking brake lever is located between
the seats. To apply the parking brake, hold
the brake pedal down and pull the parking
brake lever all the way up. To release the
parking brake, hold the brake pedal down,
pull up slightly on the parking brake lever,
push the button on the end of the lever with
your thumb, and lower the lever to its
original position.

6-1

70F-04-002E

w WARNING
• Never drive your vehicle with the
parking brake on: rear brake
effectiveness can be reduced from
over heating, brake life may be
shortened, or permanent brake
damage may result.
• If the parking brake does not hold
the vehicle securely or does not
fully release, have your vehicle
inspected immediately by an
authorized MARUTI dealer.

OTHER CONTROLS AND EQUIPMENT

844-74E-I

PEDALS

843-06-001

Clutch Pedal 1
The clutch pedal is used to disengage the
drive to the wheels when starting the
engine, stopping, or shifting the transmission
lever. Depressing the pedal disengages the
clutch.

w CAUTION
Do not drive with your foot resting on
the clutch pedal. It could result in
excessive clutch wear, clutch damage,
or unexpected loss of engine braking.

Brake Pedal 2
Your MARUTI vehicle is equipped with front
disc brakes and rear drum brakes.
Depressing the brake pedal applies both
sets of brakes.
You may hear occasional brake squeal
when you apply the brakes. This is a
normal condition caused by environmental
factors such as cold, wet, snow, etc.

w WARNING
If brake squeal is excessive and
occurs each time the brakes are
applied, you should have the brakes
checked by your MARUTI dealer.

w WARNING
Do not “ride” the brakes by applying
them continuously or resting your foot
on the pedal. This will result in
overheating of the brakes which could
cause unpredictable braking action,
longer stopping distances, or
permanent brake damage.
Accelerator Pedal 3
This pedal controls the speed of the
engine. Depressing the accelerator pedal
increases power output and speed.

6-2

OTHER CONTROLS AND EQUIPMENT

844-74E-I

FUEL FILLER CAP

GEAR LEVER

843-06-017E

843-06-004

The gear change pattern for transmission is
shown in the illustration. For details on how
to use the transmission, refer to USING
THE TRANSMISSION in the OPERATING
YOUR VEHICLE section (See page 7-3).

The fuel filler cap is located on the left rear
side of the vehicle. To unlock the fuel filler
lid, turn the key clockwise. To lock turn the
key anticlockwise.

w WARNING

843-06-005E

w WARNING
Petrol is extremely flammable. Do not
smoke when refuelling, and make sure
there are no open flames or sparks in
the area.

Remove the fuel filler cap slowly. The
fuel may be under pressure and may
spray out, causing injury.

6-3

OTHER CONTROLS AND EQUIPMENT

844-74E-I

FOLDING REAR SEAT

•

72F-06-003E

843-06-008

843-06-009

To remove - turn the cap counterclockwise. Turn the cap slowly to allow any
residual pressure to escape.
To install - turn the cap clockwise.

The rear seat of your vehicle can be folded
forward to provide additional luggage space.

To lower the seatback, pull up the lock
knobs (1 and 2) simultaneously and fold
forward the seatback. If your vehicle is
equipped with split rear seats, the right and
left seat backs can be individually folded
forward by pulling the corresponding knob.
To raise the seatback, lift it up and push
back until it locks into place.

w CAUTION
If you need to replace the fuel cap,
use only a cap specified for your
model. Using an improper fuel cap
can cause a serious malfunction of
the fuel system. You can get the
correct replacement cap from your
MARUTI dealer.

6-4

OTHER CONTROLS AND EQUIPMENT

844-74E-I

SUN VISOR

INTERIOR LIGHT SWITCH

w WARNING
Luggage or other cargo should be
stowed in the luggage compartment
with the rear seat in an upright
position, whenever possible. If you
need to carry cargo in the passenger
compartment with the rear seat back
folded forward, be sure to secure the
cargo or it may be thrown about,
causing injury. Never pile cargo higher
than the seatbacks.

w WARNING
When returning a rear seat to the
normal position, make sure that
movement of the seatback is
unobstructed and the seatback is
securely latched.

70F-04-024

843-06-010

The sun visors can be pulled down to block
glare coming through the wind screen, or
they can be unhooked and turned to the
side to block glare coming through the side
window.

This light switch has three positions which
function as described below:

w CAUTION
When unhooking and hooking a sun
visor, be sure to handle it by the hard
plastic parts or the sun visor can be
damaged.

6-5

1 The light remains off even when the
door is opened.
2 The light comes on when the door is
opened.
3 The light comes on and stays on
regardless of whether the door is open
or closed.

NOTE:
Only front doors are involved in lighting
operation of interior light.

OTHER CONTROLS AND EQUIPMENT

844-74E-I

ASSIST GRIPS

BONNET

70F-04-015

Assist grips are provided for passenger
convenience.

w WARNING
Do not hang items on the assist grips.
They could obstruct the driver’s view,
resulting in an accident, or could be
thrown about in an accident or abrupt
manoeuvre, causing injury.

843-06-011

To open the bonnet:
1) Pull the bonnet release handle located
on the outboard side of the driver’s side
of the instrument panel. This will
disengage the bonnet lock halfway.

843-06-012

2) Push the under-bonnet release lever
upwards with your finger, as shown in
the illustration. While pushing the lever,
lift up the bonnet.

6-6

OTHER CONTROLS AND EQUIPMENT

844-74E-I

TYRE CHANGING TOOLS

843-06-013

843-06-014

3) Continue to lift up the bonnet until it is
high enough to support with the prop
rod.

The jack, wheel wrench and jack handle are
stowed in the luggage compartment behind
the rear seat.

w WARNING

To remove the jack, turn its shaft
counterclockwise and pull the jack out of the
storage bracket. To stow the jack, place it
in the storage bracket and turn the shaft
clockwise until the jack is securely held in
place.

Make sure the bonnet is fully closed
and latched before driving. If it is not,
it can fly up unexpectedly during
driving, obstructing your view and
resulting in an accident.

843-06-015

w WARNING
The jack should be used only to
change wheels. It is important to read
the jacking instructions in the
EMERGENCY SERVICE section of this
manual before attempting to use the
jack.

w WARNING
After using the jack, jack handle, and
wheel wrench, be sure to stow them
securely or they can cause injury if an
accident occurs.

6-7

OPERATING YOUR VEHICLE

844-74E-I

OPERATING YOUR VEHICLE
Exhaust Gas Warning ....................................................................................... 7-1
Daily Inspection Checklist ................................................................................ 7-1
Starting the Engine ............................................................................................ 7-2
Using the Transmission .................................................................................... 7-3
Braking .................................................................................................................. 7-4
Running-in ............................................................................................................ 7-4
Catalytic Converter ............................................................................................. 7-5
Improving Fuel Economy ................................................................................. 7-6
Trailer Towing ..................................................................................................... 7-6

OPERATING YOUR VEHICLE

844-74E-I

EXHAUST GAS WARNING

DAILY INSPECTION CHECKLIST

w WARNING

•

60G-07-001E

•

w WARNING
Avoid breathing exhaust gases.
Exhaust gases contain carbon
monoxide, a potentially lethal gas that
is colourless and odourless. Since
carbon monoxide is difficult to detect
by itself, be sure to take the following
precautions to help prevent carbon
monoxide from entering your vehicle.
• Do not leave the engine running in
garages or other confined areas.
• Do not park with the engine running
for a long period of time, even in an
open area. If it is necessary to sit
for a short time in a parked vehicle

•

with the engine running, make sure
the air intake lever is set to “FRESH
AIR” and the fan is at high speed.
Avoid operating the vehicle with the
hatchback open. If it is necessary to
operate the vehicle with hatchback
open, make sure all the windows are
closed, and the fan is at high speed
with the air intake lever set to
“FRESH AIR”.
To allow proper operation of your
vehicle’s ventilation system, keep
the air inlet grille in front of the
windscreen clear of snow, leaves, or
other obstructions at all times.
Keep the exhaust tailpipe area clear
of snow and other material to help
reduce the buildup of exhaust gases
under the vehicle. This is
particularly important when parked
in blizzard conditions.
Have the exhaust system inspected
periodically for damage and leaks.
Any damage or leaks should be
repaired immediately.

70F-05-007

Before driving:
1) Make sure that windows, mirrors, lights,
and reflectors are clean and unobstructed.
2) Check the tyres.
3) Look for fluid and oil leaks.

NOTE:
It is normal for water to drip from the air
conditioning system after use.
4) Adjust the seat/head restraint.
5) Check the brake pedal and the parking
brake lever.
6) Adjust the mirrors.
7) Make sure that you and passengers
have properly fastened your seat belts.
8) Make sure that all warning lights come
on as the key is turned to the “ON” or
“START” position.
9) Check all gauges.
10)Make sure that the brake fluid level
warning light is off after starting the
engine.

7-1

OPERATING YOUR VEHICLE

844-74E-I

STARTING THE ENGINE
Once a week, or each time you fill your fuel
tank, perform the following under-bonnet
checks:
1)
2)
3)
4)
5)
6)

Engine oil level.
Coolant level.
Brake fluid level.
Windscreen washer fluid level.
Battery solution level.
Bonnet latch operation.
Pull the bonnet release handle inside the
vehicle. Make sure that you can not
open the hood all the way without
releasing the secondary latch. Be sure
to close the hood securely after checking
for proper operation. See "All Latches,
Hinges & Locks" of "PERIODIC
MAINTENANCE SCHEDULE" in the
"INSPECTION AND MAINTENANCE"
section for lubrication schedule.

w WARNING
Make sure the bonnet is fully closed
and latched before driving. If it is not,
it can fly up unexpectedly during
driving, obstructing your view and
resulting in an accident.

Before starting the engine:
1) Make sure the parking brake is applied
fully.
2) Shift into “N” (neutral) and depress the
clutch pedal all the way to the floor. Hold
it while starting the engine.

Starting a Cold Engine
Engine which is started after 6 hours should
be treated as cold engine.
For Electronic fuel injection models
•

w WARNING
Make sure that the parking brake is
applied fully and the transmission is
in Neutral before attempting to start
the engine.

•

w CAUTION
• Stop turning the starter immediately
after the engine has started or the
starter system can be damaged.
• Do not crank the engine for more
than 5 seconds at a time. If the
engine doesn’t start on the first try,
wait about 5-10 seconds before
trying again.

•

With your foot off the accelerator pedal,
crank the engine by turning the ignition
key to “START”. Release the key when
the engine starts.
If the engine does not start after 15
seconds of cranking, wait about 15
seconds, then press down the
accelerator pedal to 1/3 of its travel and
try cranking the engine again. Release
the key and accelerator pedal when the
engine starts.
If the engine still does not start, try
holding the accelerator pedal all the way
to the floor while cranking. This should
clear the engine if it is flooded.

Starting a Warm Engine
For Electronic fuel injection models:
Use the same procedure as for “Starting a
cold Engine”.

7-2

OPERATING YOUR VEHICLE

844-74E-I

USING THE TRANSMISSION

w WARNING

843-06-017E

Starting off
To start off, depress and maintain pressure
upon the clutch pedal and change into 1st
gear. After releasing the parking brake,
gradually release the clutch. When you hear
a change in the engine’s sound (speed),
gently apply pressure to the accelerator to
keep the engine sound (speed) constant
whilst continuing to gradually release the
clutch.
Gear changing
All forward gears are synchronized, which
provides for quiet, easy changing. Always
depress the clutch pedal fully before
changing gears. To help gearshift, the
following chart shows the recommended
speed range in each gear.

7-3

First

Min speed

Max. speed

–

30 km/h

Second

10 km/h

50 km/h

Third

20 km/h

90 km/h

Fourth

30 km/h

Top Speed

Fifth

40 km/h

Top Speed

• Reduce your speed and change
down to a lower gear before going
down a long or steep hill. A lower
gear will allow the engine to provide
braking. Avoid riding the brakes or
they may overheat, resulting in
brake failure.
• When driving on slippery roads, be
sure to slow down before changing
down. Excessive and or sudden
changes in engine speed may cause
loss of traction, which could cause
you to lose control.
• Make sure that the vehicle is
completely stationary before you
change into reverse.

w CAUTION
• To help avoid clutch damage, do not
use the clutch pedal as a footrest
while driving or use the clutch to
keep the vehicle stationary on a hill.
Depress the clutch fully when
changing gear.
• When changing gears or starting off,
do not race the engine. Racing the
engine can shorten engine life and
prevent smooth operation.
50

OPERATING YOUR VEHICLE

844-74E-I

RUNNING-IN

BRAKING
The distance needed to bring any vehicle
to a halt increases with the speed of the
vehicle. The braking distance needed, for
example, at 60 km/h will be approximately
4 times greater than the braking distance
needed at 20 km/h. Start to brake the
vehicle when there is plenty of distance
between your vehicle and the stopping point,
and slow down gradually.

w WARNING

w CAUTION

If water gets into the brake drums,
brake performance may become poor
and unpredictable. After driving
through water or washing the
underside of the vehicle, test the
brakes while driving at a slow speed
to see if they have maintained their
normal effectiveness. If the brakes are
less effective than normal, dry them
by repeatedly applying the brakes
while driving slowly until the brakes
have
regained
their
normal
effectiveness.

The future performance and reliability
of the engine depends on the care
and restraint exercised during its early
life. It is especially important to
observe the following precautions
during the initial 1000 km of vehicle
operation.
• After starting, do not race the
engine. Warm it up gradually.
• Avoid prolonged vehicle operation at
a constant speed. Moving parts will
bed in better if you vary your speed.
• Do not exceed 100 km/h.
• Start off from a stop slowly. Avoid
full throttle starts.
• If possible, avoid hard braking,
especially during the first 320 km
of driving.
• Do not drive slowly with the
transmission in a high gear.
• Drive the vehicle at moderate engine
speeds.

7-4

OPERATING YOUR VEHICLE

844-74E-I

CATALYTIC CONVERTER
damage to the catalyst and other vehicle
components.

w CAUTION

70F-05-005

The purpose of the catalytic converter
installed on your vehicle is to convert
exhaust pollutants to harmless water vapour,
carbon dioxide, and nitrogen. Use of leaded
fuel in vehicles equipped with catalytic
converters is prohibited, because lead
deactivates
the
pollutant-reducing
components of the catalyst system.
The converter is designed to last the life of
the vehicle under normal usage and when
unleaded fuel is used. No special
maintenance is required on the converter.
However, it is very important to keep the
engine properly tuned. Engine misfiring,
which can result from an improperly tuned
engine, may cause overheating of the
catalyst. This may result in permanent heat

7-5

To minimize the possibility of catalyst
or other vehicle damage:
• Maintain the engine in the proper
operating condition.
• In the event of an engine
malfunction, particularly one
involving engine misfire or other
apparent loss of performance, have
the vehicle serviced promptly.
• Do not turn off the engine or
interrupt the ignition when the
transmission is in gear and the
vehicle is in motion.
• Do not try to start the engine by
pushing or towing the vehicle, or
coasting down a hill.
• Do not idle the engine with any
spark plug wires disconnected or
removed, such as during diagnostic
testing.
• Do not idle the vehicle for
prolonged periods if idling seems
rough
or
there
are
other
malfunctions.
• Do not allow the fuel tank to get
near the empty level.

60G-07-002E

w WARNING
Be careful where you park and drive;
the catalytic converter and other
exhaust components can get very hot.
As with any vehicle, do not park or
operate this vehicle in areas where
combustible materials such as dry
grass or leaves can come in contact
with a hot exhaust system.

OPERATING YOUR VEHICLE

844-74E-I

IMPROVING FUEL ECONOMY
The following instructions will help you
improve fuel economy.
Avoid excessive idling:
If you are to wait for more than a minute
while you are parked, stop the engine and
start it again later. When warming up a cold
engine, allow the engine to idle until the
temperature gauge pointer comes up to the
“C” position. In this position, the engine is
sufficiently warm for starting off.
Avoid “fast” starts:
Fast starts away from lights or stop signs
will consume fuel unnecessarily and shorten
engine life. Start off slowly.
Avoid unnecessary stops:
Avoid unnecessary deceleration and
stopping. Try to maintain a slow, steady
speed whenever possible. Slowing down
and then accelerating again uses more fuel.

TRAILER TOWING
Keep the air cleaner clean:
A dirty air cleaner will cause the carburation
system to supply too much fuel to the
engine for the amount of air being supplied.
The result is waste of fuel due to incomplete
combustion.

Your MARUTI was originally designed to
carry people and a normal amount of cargo,
not to tow a trailer. Maruti does not
recommend you use your vehicle to tow a
trailer. Towing a trailer can adversely affect
handling, durability, and fuel economy.

Keep weight to a minimum:
The heavier the load, the more fuel the
vehicle consumes. Take out any luggage or
cargo when it is not necessary.
Keep tyre pressures correct:
Under-inflation of the tyres can waste fuel
due to increased running resistance of the
tyres. Keep your tyres inflated to the correct
pressure shown on the label on the driver’s
side door or door lock pillar.

Keep a steady cruising speed:
Keep as constant a speed as road and
traffic conditions will permit.

7-6

844-74E-I

DRIVING TIPS AND SAFE DRIVING

844-74E-I

DRIVING TIPS AND SAFE DRIVING
High Speed Driving ........................................................................................... 8-1
Driving on Hills .................................................................................................. 8-1
Driving on Slippery Roads .............................................................................. 8-2
Do’s and Don’ts for Safe Driving .................................................................. 8-3

DRIVING TIPS AND SAFE DRIVING

844-74E-I

HIGH-SPEED DRIVING

DRIVING ON HILLS

When driving at a high-speed, pay attention
to the following:

•

When climbing steep hills, the car may
begin to slow down and show a lack of
power. If this happens, you should
change to a lower gear so that the
engine will again be operating in its
normal power range. Change rapidly to
prevent the car from losing momentum.

•

When driving down a hill, the engine
should be used for braking by shifting to
next lower gear.

•

Stopping
distance
progressively
increases with vehicle speed. Apply the
brakes far enough ahead of the stopping
point to allow for the extra stopping
distance.

•

On rainy days, “Aquaplaning” can occur.
“Aquaplaning” is the loss of direct
contact between the road surface and
the vehicle’s tyres due to a water film
forming between them. Steering or
braking the vehicle while “Aquaplaning”
can be very difficult, and loss of control
can occur. Keep speed down when the
road surface is wet.

70F-06-001

w WARNING
• Wear Your Seat Belts at All Times.
The driver and passengers should
be properly restrained at all times,
using the seatbelts provided. Refer
to the “SEATBELTS” section for
instructions on proper use of the
seat belts.
• Never drive while under the
influence of alcohol or other drugs.
Alcohol and drugs can seriously
impair your ability to drive safely,
greatly increasing the risk of injury
to yourself and others. You should
also avoid driving when you are
tired, sick, irritated, or under stress.

8-1

•

At high speeds, the vehicle may be
affected by side winds. Therefore, reduce
speed and be prepared for unexpected
buffeting, which can occur at the exits
of tunnels, when passing by a cut of a
hill, or when being overtaken by large
vehicles, etc.

w WARNING
Try not to hold the brake pedal down
too long or too often while going
down a steep or long hill. This could
cause the brakes to overheat,
resulting in reduced braking efficiency.
Failure to take this precaution could
result in loss of vehicle control.

w CAUTION
When descending a down hill, NEVER
turn the ignition key to the “OFF”
position. Emission control system
damage may result.

DRIVING TIPS AND SAFE DRIVING

844-74E-I

DRIVING ON SLIPPERY ROADS
Under wet road conditions you should drive
at a lower speed than on dry roads due to
possible slippage of tyres during braking.
When driving on icy, snowcovered, or
muddy roads, reduce your speed and avoid
sudden acceleration, abrupt braking, or
sharp steering movements.
Snow Chains
If you must use snow chains to increase
tyre traction, observe the following
precautions:
•
•
•
•
•

Choose a safe place away from traffic
to install the chains.
When installing the chains carefully
follow the manufacturer’s instructions.
Install the chains on the front tyres.
With the chains on, drive only at slow
and moderate speeds.
If Your Vehicle Gets Stuck
If your vehicle gets stuck in snow, mud,
or sand, follow the directions below:

1) Change back and forth between first
gear and reverse. This will create a
rocking motion which may give you
enough momentum to free the vehicle.
Press gently on the accelerator to keep
wheel spin to a minimum. Remove your
57

foot from the accelerator while changing
gear.
Do not race the engine. Excessive wheel
spin will cause the tyres to dig deeper,
making it more difficult to free the
vehicle.
2) If your vehicle remains stuck after a few
minutes of rocking, get another vehicle
to pull you out.

w WARNING
Do not allow anyone to stand near the
vehicle when you are rocking it, and
do not spin the wheels faster than an
indicated 40 km/h on the speedometer.
Personal injury and/or vehicle damage
may result from spinning the wheels
too fast.

w CAUTION
Do not continue rocking the vehicle
for more than a few minutes.
Prolonged rocking can cause engine
overheating or transmission damage.

w WARNING
• Make sure your tyres are in good
condition and always maintain the
specified tyre pressure. Refer to
“TYRES” in the “INSPECTION AND
MAINTENANCE” section for details.
• Do not use tyres other than those
specified by MARUTI. never use
different sizes or types of tyres on
the front and rear wheels. For
information regarding the specified
tyres, refer to the “SPECIFICATIONS” section.
• Never use oversized tyres or special
shock absorbers and springs to
raise (jack up) your vehicle. This will
change the handling characteristics.
• After driving through water, test the
brakes while driving at a slow speed
to see if they have maintained their
normal effectiveness. If the brakes
are less effective than normal, dry
them by repeatedly applying the
brakes while driving slowly until the
brakes have regained their normal
effectiveness.

8-2

DRIVING TIPS AND SAFE DRIVING

844-74E-I

DO’S AND DON’TS FOR SAFE
DRIVING
Exercise care in handling your vehicle. Be
conscious of not only your own safety but
also the safety of others on the road, and
thus enjoy the best and most comfortable
driving experience.
This section contains basic rules for safe
driving. Read it carefully for good
understanding of the content so that you
can enjoy safe and pleasant driving in your
Maruti vehicle.
72F-08-002

72F-08-008

Starting
1. Adjust the driver’s seat for the proper
driving posture.

2. Always follow other vehicles at a safe
distance in order to prevent a rear-end
collision, should the vehicle ahead make
a sudden stop.

2. Adjust the rear view mirror so as to
obtain the best possible rear view.
3. Before moving off, look forward and back
to confirm safety.
4. Don’t start quickly, for it is dangerous
and wastes fuel.
General driving
1. Be sure to stop before the stop light and
stop sign. When moving into the
intersection without any traffic lights or
signs, drive slowly to confirm safety.

8-3

3. Turn ON the turn signal at least 30
meters before making a turn or changing
the lane so as not to be hit from behind.
4. Before entering a corner, decelerate to
a safe speed. Don’t apply brakes during
cornering, or a cornering skid may occur.
5. When overtaking other vehicles, watch
out for the oncoming vehicle and
carefully confirm the safety.
6. Don’t attempt zigzag driving which will
hinder your control over the vehicle and
cause an accident.
58

DRIVING TIPS AND SAFE DRIVING

844-74E-I

72F-08-012

72F-08-015

especially dangerous when the tyres are
worn, for they allow a larger skid.

5. The higher the speed, the narrower the
driver’s visual range becomes. In such
a state, it is difficult to anticipate any
hazard and the driver feels much
fatigued.

Use foot brake in three stages
(1) Warn the vehicle behind you
(2) Gradually apply the brake.
(3) Bring the vehicle to a halt.
72F-08-011

Braking
1. Use the parking brake when parking
your vehicle and shift the gear shift lever
into the first gear or reverse gear
position for the sake of safety.
2. Don’t
use
handbraking
unless
unavoidable. It causes the vehicle to skid
and a rearend collision occur. It is
59

3. When driving on a downhill, try not to
apply the brake but use the engine
brake effectively. Overuse of the
footbrake may result in total brake
failure.
4. Avoid reckless high speed driving and try
to drive at a safe speed suitable for the
road conditions while maintaining a
constant speed.

6. Never do sharp handling during high
speed driving. You will lose your control
over your vehicle.
7. When overtaking or changing the lane
while driving at a high speed, keep an
ample vehicle-to-vehicle distance.
Long distance driving
1. Be sure to perform safety checks before
starting a trip.
2. Take rest at certain intervals to prevent
an accident which may occur when you
are sleepy or tired.

8-4

DRIVING TIPS AND SAFE DRIVING

844-74E-I

MARGIN FOR SAFETY
It is important to allow yourself a margin for
safety during driving so that you can cope
with erroneous or unexpected driving of
other drivers. For that, observe the following.
•
•
•
•
72F-08-020

72F-08-021

Drive at a safe speed.
Maintain a sufficient distance between
your vehicle and the vehicle ahead.
Don’t force yourself to overtake other
vehicles.
Don’t make quick start, hard steering or
sudden stops.
Allow an ample time in the driving
schedule.
Observe traffic rules and regulations.

Night time driving
1. Drive more slowly at night than in the
daytime, for the visual range is restricted
at night.

•

2. Don’t overtake other vehicles at night.
Darkness bothers your sense of speed
and hinders your judgement on the
vehicle-to-vehicle distance.

A perfect driver does not exist. The
endeavour of every motorist should be to
strive for perfection. Safety consciousness
not only ensures your safety and the safety
of other road users, it also helps reduce the
wear and tear on your vehicle, prolongs its
life, gives more mileage and ensures a
comfortable driving experience.

3. Don’t use the high headlight beam
unless its use is inevitable. Its dazzle
may blitz the driver of the oncoming
vehicle, thus causing an accident.
4. Always keep the window glasses clean.
Don’t operate the windshield wiper when
the windshield glass is dry or the wiper
blade and glass may get damaged.

8-5

•

CONCLUSION

72F-08-022

Follow the do’s and don’ts listed, and
driving will never be the same again.

INSPECTION AND MAINTENANCE

844-74E-I

INSPECTION AND MAINTENANCE
Periodic Maintenance Schedule ......................................................................... 9-1
Drive Belt .............................................................................................................. 9-6
Engine Oil and Filter ............................................................................................ 9-7
Gear Oil ............................................................................................................... 9-10
Engine Coolant ................................................................................................... 9-11
Windscreen Washer Fluid ................................................................................. 9-12
Air Cleaner .......................................................................................................... 9-12
Spark Plugs ........................................................................................................ 9-13
Brakes ................................................................................................................. 9-14
Steering ............................................................................................................... 9-16
Clutch Pedal ....................................................................................................... 9-16
Tyres .................................................................................................................... 9-17
Battery ................................................................................................................. 9-20
Fuses ................................................................................................................... 9-20
Bulb Replacement .............................................................................................. 9-22
Wiper Blades ...................................................................................................... 9-25

INSPECTION AND MAINTENANCE

844-74E-I

PERIODIC MAINTENANCE SCHEDULE

w WARNING
• Do not allow smoking, sparks, or
flames around gasoline or the
battery. Flammable fumes are
present.
• Do not get under your vehicle if it
is supported only with the portable
jack provided in your vehicle.
• Be careful not to cause accidental
short circuits between the positive
and negative battery terminals.
• Keep used oil, coolant, and other
fluids away from children and pets.
Dispose of used fluids properly;
never pour them on the ground, into
sewers, etc.

The following table shows when regular
maintenance on your vehicle is required.
This table shows in kilometres and months
when inspections, adjustments, lubrication
and other services should be performed.

w WARNING
Maruti recommends that maintenance
on your Maruti vehicle be performed
by Maruti Authorised Dealer/Service
Station.

w CAUTION
Whenever it becomes necessary to
replace parts on your vehicle, it is
recommended that you use MARUTI
GENUINE PARTS (MGP).

You should take extreme care when
working on your vehicle to prevent
accidental injury. Here are a few
precautions that you should be
especially careful to observe:
• Do not leave the engine running in
garages or other confined areas.
• When the engine is running, keep
hands, clothing, tools, and other
objects away from the fan and water
pump belt. Even though the fan may
not be moving, it can automatically
turn on without warning.
• When it is necessary to do service
work with the engine running, make
sure that the parking brake is
applied fully and the transmission is
in Neutral.
• Do not touch ignition wires or other
ignition system parts when starting
the engine or when the engine is
running, or you could receive an
electric shock.
• Be careful not to touch hot exhaust
components such as the manifold,
pipes, and mufflers.

w WARNING

9-1

INSPECTION AND MAINTENANCE

844-74E-I

A....Adjust.
T....Tighten to specified torque.
R....Replace or change.
L....Lubricate.

I....Inspect and correct or replace if necessary.
C....Clean.
O....Rotate

Note:
This table includes services as scheduled up to 80,000 km mileage. Beyond 80,000 km, carry out the same services at the same intervals
respectively.
Interval: This interval should be judged
by odometer reading or months,
whichever comes first.

km
(x 1,000)
months

FREE INSPECTIONS
1
5
10
1
6
12

PERIODIC MAINTENANCE SERVICE AT COST
20
30
40
50
60
70
80
24
36
48
60
72
84
96

ENGINE
1. Water pump drive belt (tension, wear)

2. Engine coolant (level, leakage)

3. Engine oil (API GRADE SF, SG, SH) & Oil filter

4. Cooling system hoses and connections (leakage, damage)

5. Engine bolts (All cylinder head and manifold fixings)

–

6. Engine mounting (loose, damage)

–

7. Valve clearance

–

8. Camshaft timing belt (damage, wear)

–
–
–
I
Replace every 1,00,000 km

–

9. Exhaust system (noise, leakage or otherwise defective)

–

10. Positive crankcase ventilation System (Hoses, connections and valve)

–

IGNITION

1. Ignition wiring, (damage, deterioration)

–

2. Distributor cap and rotor (wear, deterioration)

–

3. Spark plugs (clean and adjust the gap)

–

9-2

INSPECTION AND MAINTENANCE

844-74E-I

Interval: This interval should be judged
by odometer reading or months,
whichever comes first.

km
(x 1,000)
months

FREE INSPECTIONS

PERIODIC MAINTENANCE SERVICE AT COST

1
1

20
24

5
6

10
12

30
36

40
48

50
60

60
72

70
84

80
96

FUEL
1. Air cleaner

Paved-road

Clean every 5,000 km. Replace every 40,000 km.

Dusty condition

Clean every 2,500 km or as required. Replace every 40,000 km. More frequent
replacement if dust condition is severe.

2. Accelerator cable and Throttle shafts

–

I&L

3. Fuel tank cap, fuel lines & connections(leakage,damage)

–

I&L
I

4. Fuel filter (leakage)

1. Clutch pedal (play)

2. Clutch slipping (dragging or excessive damage)

3. Manual Transmission/Transfer and Differential oil (level, leakage)

–

CLUTCH AND TRANSMISSION

DRIVE SHAFTS
1. Drive shafts boots (bent of boots damage)
BRAKE
1. Brake fluid (level, leakage)

2. Brake pedal (pedal-to-wall clearance)

3. Parking brake lever and cable (play, damage)

4. a. Brake discs and pads, (wear)
b. Brake drums & shoes

–
–

I
–

I
I

5. Master cylinder and wheel cylinder or calliper (oil leakage, boot kit)

6. Brake hoses and pipes (leakage, damage)

9-3

INSPECTION AND MAINTENANCE

844-74E-I

Interval: This interval should be judged
by odometer reading or months,
whichever comes first.

FREE INSPECTIONS
km
(x 1,000)
months

WHEEL
1. Tyres (air pressure, abnormal wear, crack, ROTATION)

1
1

5
6

10
12

PERIODIC MAINTENANCE SERVICE AT COST
20
24

30
36

40
48

50
60

60
72

70
84

80
96

Rotate and inspect every 5,000 km

2. Wheels (damage)

3. Front wheel bearings (loose, damage)

–

4. Rear wheel bearings (loose, damage)

–

FRONT AND REAR SUSPENSION
1. Suspension strut (oil leakage, damage)

2. Suspension arms and knuckle supports (loose,damage)

–

3. Rear spring (damage)

–

4. Shock absorbers (oil leakage, damage)

5. All bolts and nuts (loose)

–

6. Suspension arms and Tension rods

–

STEERING
1. Steering wheel (play, loose)

2. Steering gear box (loose, leakage)

3. All rods and arms (loose, damage, wear)

ELECTRICAL
1. Battery electrolyte (level, leakage)

2. Wiring harness connection (looseness, damage)

–

3. Lighting system (operation, stains, damage)

4. Horn (operation)

5. System voltage

–

BODY

1. All chassis bolts and nuts (tighten)

–

2. All Latches, Hinges & Locks (function)

I&L

9-4

INSPECTION AND MAINTENANCE

Interval: This interval should be judged
by odometer reading or months,
whichever comes first.

844-74E-I

km
(x 1,000)
months

FREE INSPECTIONS
1
5
10
1
6
12

PERIODIC MAINTENANCE SERVICE AT COST
20
30
40
50
60
70
80
24
36
48
60
72
84
96

ROAD TEST
1. Operation of Brakes, Gear shifting & speedometer

2. Body and Chassis noise

AIR CONDITIONER (if equipped)
1. Check belt tension

2. Check Receiver Drier bubbles.

3. Tighten compressor mounting bolts

–

T
I

4. Check all hose joints, tighten if necessary

5. Check functioning of Recirc flap

6. Clean condenser with low pressure water

–

7. Check belt for frayed edges, change if necessary

–

8. Check all mounting bolts

–

9-5

INSPECTION AND MAINTENANCE

844-74E-I

DRIVE BELT

w WARNING
• All maintenance should be carried
out with the ignition switch in the
“OFF” position and the car parked
securely on the level ground unless
otherwise specified.
• If you are in any way unsure of your
ability to undertake a task, then do
not start it but contact your Maruti
dealer to perform the work for you.
843-09-001E

843-09-025E

w WARNING

Water pump belt

6 - 7 mm

When the engine is running, keep
hands, hair, clothing, tools, etc. away
from the fan and water pump belt.
Even though the fan may not be
moving, it can automatically turn on
without warning.

Air conditioner belt

7 - 9 mm

The belt should also be examined to ensure
that it is not damaged. If the belt needs to
be replaced or adjusted, have it done by
your MARUTI dealer.

Make sure the drive belt tension is correct.
If the belt is too loose, insufficient battery
charging, engine overheating, or excessive
belt wear can result. When you press the
belt with your thumb midway between the
pulleys, the belt deflection should be within
the specification below.
67

9-6

INSPECTION AND MAINTENANCE

844-74E-I

ENGINE OIL AND FILTER

70F-07-004E

Specified oil
Be sure that the engine oil you use comes
under the API classification of SF, SG or
SH. Select the appropriate oil viscosity
according to the above chart.

843-09-002

Oil Level Check
It is important to keep the engine oil at the
correct level for proper lubrication of your
vehicle’s engine. Check the oil level with the
vehicle on a level surface. The oil level
indication may be inaccurate if the vehicle
is on a slope. The oil level should be
checked either before starting the engine or
at least five minutes after stopping the
engine.
Pull out the oil dipstick, wipe oil off with a
clean cloth, insert the dipstick all the way
into the engine, then remove it again. The
oil on the stick should be between the upper
and lower limits shown on the stick. If the

9-7

INSPECTION AND MAINTENANCE

844-74E-I

70F-03-008E

79F-09-003E

oil level indication is near the lower limit,
add enough oil to raise the level to the
upper limit.

Refilling
Remove the oil filler cap and pour oil slowly
through the filler hole to bring the oil level
to the upper limit on the dipstick. Be careful
not to overfill. Too much oil is almost as
bad as too little oil. After refilling, start the
engine and allow it to idle for about a
minute. Stop the engine, wait for two or
three minutes and check the oil level again.

70F-07-009

Tightening torque:
5.0 kg-m (36.5 lb-ft)

w WARNING
The engine oil temperature may be
high enough to burn your fingers
when the drain plug is loosened. Wait
until the drain plug is cool enough to
touch with your bare hands.

Changing Engine Oil and Filter
Drain the engine oil while the engine is still
warm.
1) Remove the oil filler cap.
2) Place a drain pan under the drain plug.
3) Using the correct spanner remove the
drain plug and drain out the engine oil.
69

9-8

INSPECTION AND MAINTENANCE

844-74E-I

w WARNING
New and used oil can be hazardous.
Children and pets may be harmed by
swallowing new or used oil. Keep new
and used oil and used oil filters away
from children and pets.
Continuous contact with used engine
oil has been found to cause (skin)
cancer in laboratory animals.
Brief contact with used oil may irritate
skin.
To minimize your exposure to used
oil, wear a long-sleeve shirt and
moistureproof gloves (such as
dishwashing gloves) when changing
oil. If oil contacts your skin, wash
thoroughly with soap and water.
Launder any clothing or rags if wet
with oil.
Recycle or properly dispose of used
oil and filters.
4) Reinstall the drain plug and gasket.
Tighten
the plug to a torque of
5.0 kg-m (36.5 lb-ft).

70F-07-010

Replace the oil filter
1) Using an oil filter wrench, turn the oil
filter counterclockwise and remove it.
2) Using a clean rag, wipe off the mounting
surface on the engine where the new
filter will be seated.
3) Smear a little engine oil around the
rubber gasket of the new oil filter.
4) Screw on the new filter by hand until the
filter gasket contacts the mounting
surface.

70F-07-011E

Tightening torque: 1.4 kg-m (10.5 lb-ft)

w CAUTION
To tighten the oil filter properly, it is
important to accurately identify the
position at which the filter gasket first
contacts the mounting surface.
5) Tighten the filter 3/4 turn from the point
of contact with the mounting surface [or
to 1.4 kg-m (10.5 lb-ft)] using an oil filter
wrench.

w CAUTION
To prevent oil leakage, make sure that
the oil filter is tight, but do not
overtighten it.

9-9

INSPECTION AND MAINTENANCE

844-74E-I

GEAR OIL
Refill with oil and check for leaks.
1) Pour oil through the filler hole and install
the filler cap.
For the approximate capacity of the oil,
refer to the "CAPACITIES" item in the
"SPECIFICATIONS" section.
2) Start the engine and look carefully for
leaks at the oil filter and drain plug. Run
the engine at various speeds for at least
5 minutes.
3) Stop the engine and wait for five
minutes. Check the oil level again and
add oil if necessary. Check for leaks
again.

w CAUTION
When replacing the oil filter, it is
recommended that you use a genuine
MARUTI replacement filter.

w CAUTION
Oil leaks from around the oil filter or
drain
plug
indicate
incorrect
installation or gasket damage. If you
find any leaks or are not sure that the
filter has been properly tightened,
have the vehicle inspected by your
MARUTI dealer.

70F-07-012E

Oil filler and level plug 1
Tightening torque:
2.1 kg-m (21 N.m, 15.5 lb-ft)
Specified Manual Transmission oil
When adding gear oil, use the appropriate
viscosity and grade as shown in the chart
below. We highly recommend you use API
GL-4 SAE 75W-90 gear oil.
Type of oil

Gear oil, API GL-4

70F-07-013E

Gear oil level check
To check the gear oil level, use the
following procedure:
1) Park the vehicle on a level surface with
the parking brake applied.
2) Clean casing around oil filler plug to
remove risk of any loose dirt or debris
entering oil filler plug hole. Remove the
oil filler plug 1.
3) Feel the inside of the hole with your
finger. If the oil level comes up to the
bottom of the plug hole, the oil level is
correct. If so, reinstall the plug.
4) If the oil level is low, add gear oil
through the filler plug hole 1 until the
oil level reaches the bottom of the filler
hole, then reinstall the plug.

9-10

INSPECTION AND MAINTENANCE

844-74E-I

ENGINE COOLANT
Adding Coolant
If the Coolant level is below the “LOW”
mark, more coolant should be added.
Remove the reservoir tank cap and add
coolant until the reservoir tank level reaches
the “FULL” mark. Never fill the reservoir
tank above the “FULL” mark.

w WARNING
After driving the vehicle, the
transmission oil temperature may be
high enough to burn you. Wait until
the oil filler plug is cool enough to
touch with your bare hands before
inspecting transmission oil.

w CAUTION

w CAUTION
When tightening the plug, apply
sealing compound to the plug
threads to prevent oil leakage.
Gear oil change
Since special procedures, materials and
tools are required, it is recommended that
you trust this job to your authorized
MARUTI dealer.

9-11

843-09-004E

Coolant Level Check
Check the coolant level at the reservoir
tank, not at the radiator. With the engine
cool, the coolant level should be between
the “FULL” and “LOW” marks.

• When adding or replacing coolant,
use a high quality ethylene glycol
antifreeze and anticorrosion diluted
with distilled water. If the lowest
ambient temperature in your area is
expected to be -150C (50F) or above,
make the antifreeze concentration of
the mixture you use at least 30%
but no more than 50%. If -160C (30F)
or below, make the concentration at
least 50%. If the 50% concentration
does
not
provide
adequate
protection against freezing, follow
the instructions on the antifreeze
container to obtain the desired
freezing point.

INSPECTION AND MAINTENANCE

844-74E-I

WINDSCREEN WASHER FLUID

60G-09-039E

w WARNING
It is dangerous to remove the radiator
cap when the water temperature is
high, because scalding fluid and
steam may be blown out under
pressure. Wait until the coolant
temperature has lowered before
removing the cap.
Coolant Replacement
Since special procedures, materials and
tools are required, it is recommended that
you trust this job to your authorized
MARUTI dealer.

AIR CLEANER

843-09-006E

843-09-023

Check that there is washer fluid in the tank.
Refill it if necessary. Use a good quality
windscreen washer fluid, diluted with water
as necessary.

If the air cleaner is clogged with dust, there
will be greater intake resistance, resulting in
decreased power output and increased fuel
consumption.

w WARNING

Take out the air cleaner case after opening
bolts 1. Take out the air cleaner element
after unhooking the clamps 2 as shown in
the illustration. Blow off dust on air cleaner
element by compressed air. If the air
cleaner element appears to be dirty, replace
it with a new one.

Do not use “antifreeze” solution in the
windscreen washer reservoir. This can
severely impair visibility when sprayed
on the windscreen, and can also
damage your vehicle’s paint.

w CAUTION
Damage may result if the washer
motor is operated whilst the fluid or
fluid nozzles are frozen or with no
fluid in the washer tank.

9-12

INSPECTION AND MAINTENANCE

844-74E-I

SPARK PLUGS

w CAUTION
The air cleaner element should be
replaced every 40,000 km. More
frequent replacement is necessary
when you drive under dusty
conditions.

60G-09-011E

You should inspect spark plugs periodically
for carbon deposits. When carbon
accumulates on a spark plug, a strong spark
may not be produced. Remove carbon
deposits with a wire or pin and adjust the
spark plug gap.

w CAUTION
• When disconnecting the spark plug
cables, pull on the boot, not on the
cable itself. Pulling on the cable can
damage it.
• When installing the spark plugs,
screw them in with your fingers to
avoid stripping the threads. Tighten
with a torque wrench to 1.5 kg-m
(15 N-m, 10.5 lb-ft). Do not allow

w CAUTION
contaminants to enter the engine
through the spark plug holes when
the plugs are removed.
• Never use spark plugs with the
wrong thread size or length.

w CAUTION
When replacing spark plugs, you
should use the brand and type
specified for your vehicle. For the
specified plugs, refer to the
“SPECIFICATIONS” section at the end
of this book.

9-13

79F-09-014E

843-09-024E

INSPECTION AND MAINTENANCE

844-74E-I

BRAKES

843-09-007

NOTE:
If you experience some firing problem of
spark plugs, such as, hard engine-starting,
misfire etc., the cause may be located not
only on spark plugs but also on deteriorated
ignition wiring (generally, used for more than
80,000 km or five years). If spark plug
replacement does not solve the problem,
have the ignition wiring and other ignition
system inspected by your MARUTI dealer.

Brake Fluid
Check the brake fluid level by looking at the
reservoir in the engine compartment. Check
that the fluid level is between the “MAX”
and “MIN” lines. If the brake fluid level is
near the “MIN” line, fill it up to the “MAX”
line with SAE J1703 or DOT-3 brake fluid.

w WARNING
Failure to follow the guidelines below
can result in personal injury or
serious damage to the brake system.
• If the brake fluid in the reservoir
drops below a certain level, the
brake warning light on the
instrument panel will come on (the

70F-07-029

w WARNING

843-09-022E

engine must be running). Should the
light come on, immediately ask your
MARUTI dealer to inspect the brake
system.
• A rapid fluid loss indicates a leak in
the brake system which should be
inspected by your MARUTI dealer
immediately.
• Brake fluid can harm your eyes and
damage painted surfaces. Use
caution when refilling the reservoir.

9-14

INSPECTION AND MAINTENANCE

844-74E-I

NOTE:
When measuring the distance between the
brake pedal and floor wall, be sure not to
include any floor covering in the
measurement.

w WARNING
• Do not use any fluid other than SAE
J1703 or DOT-3 brake fluid. Do not
use reclaimed fluid or fluid that has
been stored in old or open
containers. It is essential that
foreign particles and other liquids
are kept out of the brake fluid
reservoir.

w CAUTION
The brake fluid should be replaced
every two years or 20,000 km.

NOTE:
With disc brakes, the fluid level can be
expected to gradually fall as the brake pads
wear.

9-15

w WARNING

70F-07-030

Brake Pedal
Check if the brake pedal stops at the
regular height without "spongy" feeling when
you depress it. If not, have the brake
system inspected by your MARUTI dealer.
If you doubt the brake pedal for the regular
height, check it as follows:

If you experience any of the following
problems with your vehicle’s brake
system, have the vehicle inspected
immediately by your MARUTI dealer.
• Poor braking performance
• Uneven braking (Brakes not working
uniformly on all wheels.)
• Excessive pedal travel
• Brake dragging
• Excessive noise
• Pedal pulsation (Pedal pulsates
when depressed.)

With the engine running, measure the
distance between the brake pedal and floor
wall when the pedal is depressed with
approximately 30 kg (66 lbs) of force. The
minimum distance required is 85 mm (3.4
in). Since your vehicle’s brake system is
self-adjusting, there is no need for pedal
adjustment. If the pedal to floor wall
distance as measured above is less than
the minimum distance required, have your
vehicle inspected by your MARUTI dealer.
76

INSPECTION AND MAINTENANCE

844-74E-I

STEERING

CLUTCH PEDAL

70F-07-031E

70F-07-033

70F-07-034

Parking brake
Check the parking brake for proper
adjustment by counting the number of clicks
made by the ratchet teeth as you slowly pull
up on the parking brake lever to the point
of full engagement. The parking brake lever
should stop between the 3rd and 6th ratchet
tooth and the rear wheels should be
securely locked. If the parking brake is not
properly adjusted or the brakes drag after
the lever has been fully released, have the
parking brake inspected and/or adjusted by
your MARUTI dealer.

Check the play of the steering wheel by
gently turning it from left to right and
measuring the distance that it moves before
you feel slight resistance. The play should
be between 0 – 30 mm (0.0 – 1.2 in).

Measure the clutch pedal play by moving
the clutch pedal with your hand and
measuring the distance it moves until you
feel slight resistance. The play in the clutch
pedal should be between 15 – 20 mm
(0.6 – 0.8 in). If the play is more or less
than the above, or clutch dragging is felt
with the pedal fully depressed, have the
clutch inspected by your MARUTI dealer.

Check that the steering wheel turns easily
and smoothly without rattling by turning it
all the way to the right and to the left while
driving very slowly in an open area. If the
amount of free play is outside the
specification or you find anything else to be
wrong, an inspection must be performed by
your MARUTI dealer.

9-16

INSPECTION AND MAINTENANCE

844-74E-I

TYRES

w WARNING

70F-07-035

The front and rear tyre pressure
specifications for your vehicle are listed on
the Tyre Inflation Pressure Label and in the
“SPECIFICATIONS” section at the end of
this book. Both the front and rear tyres
should have the specified tyre pressure.
Tyre Inspection
Inspect your vehicle’s tyres periodically by
performing the following checks:
1) Measure the air pressure with a tyre
gauge. Adjust the pressure if necessary.

9-17

• Air pressures should be checked
when the tyres are cold or you may
get inaccurate readings.
• Check the inflation pressure from
time to time while inflating the tyre
gradually, until the specified
pressure is obtained.
• Never underinflate or overinflate the
tyres.
Underinflation can cause unusual
handling characteristics or can
cause the rim to slip on the tyre
bead, resulting in an accident or
damage to the tyre or rim.
Overinflation can cause the tyre to
burst, resulting in personal injury.
Overinflation can also cause
unusual handling characteristics
which may result in an accident.

70F-07-037E

2) Check that the depth of the tread groove
is more than 1.6 mm (0.06 in). To help
you check this, the tyres have mouldedin tread wear indicators in the grooves.
When the indicators appear on the tread
surface, the remaining depth of the tread
is 1.6 mm (0.06 in) or less and the tyre
should be replaced.
3) Check for abnormal wear, cracks and
damage. Any tyres with cracks or other
damage should be replaced. If any tyres
show abnormal wear, have them
inspected by your MARUTI dealer.

INSPECTION AND MAINTENANCE

844-74E-I

w WARNING

Hitting curbs and running over rocks
can damage tyres and affect wheel
alignment. Be sure to have tyres and
wheel alignment checked periodically
by your MARUTI dealer.
4) Check for loose wheel nuts.
5) Check that there are no nails, stones, or
other objects sticking into the tyres.

Replacing the wheels and tyres
equipped on your vehicle with certain
combinations of aftermarket wheels
and tyres can significantly change the
steering and handling characteristics
of your vehicle. Therefore, use only
those wheel and tyre combinations
approved by MARUTI as standard or
optional equipment for your vehicle.

w WARNING

w CAUTION

Your MARUTI is equipped with tyres
which are all the same type and size.
This is important to ensure proper
steering and handling of the vehicle.
Never mix tyres of different size or
type on the four wheels of your
vehicle. The size and type of tyres
used should be only those approved
by MARUTI as standard or optional
equipment for your vehicle.

Replacing the original tyres with tyres
of a different size may result in false
speedometer or odometer readings.

60G-09-019E

Tyre Rotation
To avoid uneven wear of your tyres and to
prolong their life, rotate the tyres as
illustrated. Tyres should be rotated every
5,000 km as recommended in the periodic
maintenance schedule. After rotation, adjust
front and rear tyre pressures to the
specification listed on your vehicle’s Tyre
Inflation Pressure Label.

9-18

INSPECTION AND MAINTENANCE

844-74E-I

843-06-014

843-06-015

79F-09-020E

Changing Wheels
To change a wheel, use the following
procedure:

5) Install the new wheel and replace the
wheel nuts with their cone shaped end
facing the wheel. Tighten each nut
snugly by hand until the wheel is
securely seated on the hub.

6) Lower the jack and fully tighten the nuts
[4.0 – 7.0 kg-m (28.9 – 50.5 lb-ft)] in a
crisscross fashion with a wrench as
shown in the illustration.

1) Remove the jack , tools and spare wheel
from the vehicle
2) Loosen, but do not remove the wheel
nuts.
3) Jack up the vehicle (follow the jacking
instructions in the EMERGENCY
SERVICE section in this manual)
4) Remove the wheel nuts and wheel.

9-19

INSPECTION AND MAINTENANCE

844-74E-I

BATTERY

FUSES

w WARNING
To avoid harm to yourself or damage
to your vehicle or battery, follow the
jump starting instructions in the
EMERGENCY SERVICE section of this
manual if it is necessary to jump start
your vehicle.

70F-07-041

w WARNING
Batteries produce flammable hydrogen
gas. Keep flames and sparks away
from the battery or an explosion may
occur. Never smoke when working in
the vicinity of the battery .

w WARNING
When checking or servicing the
battery, disconnect the negative cable.
Be careful not to cause a short circuit
by allowing metal objects to contact
the battery posts and the vehicle at
the same time.

The level of the battery solution must be
kept between the “UPPER” and the
“LOWER” level lines at all times. If the level
is found to be below the “LOWER” level
line, add distilled water to the “UPPER” level
line. You should periodically check the
battery, battery terminals, and battery holddown bracket for corrosion. Remove
corrosion using a stiff brush and ammonia
mixed with water, or baking soda mixed with
water. After removing corrosion, rinse with
clean water.
If your vehicle is not going to be driven for
a month or longer, disconnect the cable
from the negative terminal of the battery to
help prevent discharge.

843-09-010E

This vehicle has two types of fuses, as
described below :
Main Fuse (fusible link) - The main fuse
takes current directly from the battery.
Individual Fuses - These fuses are in the
fuse box and for individual electrical circuits.
Main Fuse (fusible link)
The main fuse is located on the positive
terminal of battery in the engine
compartment. If the main fuse blows, no
electrical component will function. When
replacing the main fuse, use a genuine
MARUTI replacement.

9-20

INSPECTION AND MAINTENANCE

844-74E-I

843-09-012

w WARNING
If the main fuse blows, be sure to
have your vehicle inspected by an
authorized MARUTI dealer. Always use
a genuine MARUTI replacement. Never
use a substitute such as a wire even
for a temporary repair, or extensive
electrical damage and a fire can result.
Fuse Box
The fuse fox is located under the driver’s
side of the dashboard. Remove the fuse box
cover by pushing in at both ends and pulling
off the cover. To identify the amperage and
location, refer to the fuse list shown on the
back of the fuse box cover. To remove a

9-21

70F-07-044E

fuse, hook the fuse with the end hook on
the fuse box cover, and pull out the fuse.

w WARNING

70F-07-045E

NOTE:
Make sure that the fuse box always carries
spare fuses.

Always be sure to replace a blown
fuse with a fuse of the correct
amperage. Never use a substitute
such as aluminium foil or wire to
replace a blown fuse. If you replace
a fuse and the new one blows in a
short period of time, you may have a
major electrical problem. Have your
vehicle inspected immediately by your
MARUTI dealer.

INSPECTION AND MAINTENANCE

844-74E-I

BULB REPLACEMENT

w WARNING
• Light bulbs can be hot enough to
burn your finger right after being
turned off. This is true especially for
halogen headlight bulbs. Replace
the bulbs after they become cool
enough.
• The headlight bulbs are filled with
pressurized halogen gas. They can
burst and injure you if they are hit
or dropped. Handle them carefully.
70F-07-046E

843-09-014

w CAUTION
The oils from your skin may cause a
halogen bulb to overheat and burst
when the lights are on. Grasp a new
bulb with a clean cloth.

w CAUTION
Frequent replacement of a bulb
indicates the need for an inspection of
the electrical system. This should be
carried out by your MARUTI dealer.

Interior Light
Pull down on the rear part of lens to
remove. To install it, hook its front end in
and push it up.
The bulb can be removed by simply pulling
it out. When replacing the bulb, make sure
that the contact springs are holding the bulb
securely.

843-09-026

9-22

INSPECTION AND MAINTENANCE

844-74E-I

70F-07-049

70F-07-050E

70F-07-051E

Headlights
Open the bonnet. Remove the socket and
rubber cover. Then unhook the bulb holding
spring and replace the bulb.

Front Clearance/Turn Signal Light, Side
Turn Signal Light, rear Combination
Light, Registration Plate Light.
To remove a bulb holder from a light
housing, turn the holder counterclockwise
and pull it out. To install the holder, push
the holder in and turn it clockwise.

To remove a round bulb from a bulb holder,
push in the bulb and turn it
counterclockwise. To install a new bulb,
push it in and turn it clockwise. You can
access the individual bulb holders as
described below:

Two types (small oval and round) of bulb
are used for these lights. To remove and
install a small oval bulb, simply pull out or
push in the bulb.

9-23

INSPECTION AND MAINTENANCE

844-74E-I

843-09-017

70F-07-053

Front clearance light
Open the bonnet and support it with the
prop rod.

843-09-020

Rear combination light (tail, stop, turn
signal, etc.)
Undo the screws that secure the housing
and remove the housing.

Front turn signal light
Undo the two screws and remove the lens.
Side turn signal light
Remove the lens by using a plain screw
driver covered with a soft cloth.

70F-07-054

9-24

INSPECTION AND MAINTENANCE

844-74E-I

WIPER BLADES

70F-07-056

70F-07-059

Registration plate light
Undo the two screws and remove the light
housing.

If the wiper blades become brittle or
damaged, or make streaks when wiping,
replace the wiper blades.

w CAUTION
To avoid scratching or breaking the
window, do not let the wiper arm
strike the windshield while replacing
the wiper blade.

9-25

w CAUTION
The left and the right wiper arm
assemblies are different from each
other. In case you have to remove the
wiper arm assemblies for any reason,
remember not to interchange the two
while fitting them back. Wrong fitment
may lead to windshield breakage.

844-74E-I

EMERGENCY SERVICE

EMERGENCY SERVICE
Jacking Instructions ......................................................................................... 10-1
Jump Starting Instructions ............................................................................. 10-2
Towing ................................................................................................................ 10-4
Emergency Remedies ...................................................................................... 10-4

EMERGENCY SERVICE

844-74E-I

JACKING INSTRUCTIONS

843-06-014

1) Park the vehicle securely on hard level
ground.
2) Choke the front and rear wheel
diagonally opposite the wheel to be
changed.
3) Switch on the hazard warning flasher if
your vehicle is in or near traffic.
4) Slacken but do not remove wheel nuts
on the wheel to be changed.
5) Position the jack vertically and raise the
jack by turning the jack handle clockwise
until the jack head fits the front
suspension arm or the rear axle as
shown overleaf.

843-06-015

w CAUTION

w WARNING

Do not put the jack head on to the
lateral rod (if equipped), or the lateral
rod will be damaged.

• Use the jack only to change wheels.
• Never jack up the vehicle on an
inclined surface.
• Never raise the vehicle with the jack
in a location other than the place
specified in the illustration near the
wheel to be changed.
• Make sure that the jack is raised at
least 2 inches (51 mm) before it
contacts the vehicle. Use of the jack
when it is within 2 inches of being
fully collapsed may result in failure
of the jack.

6) Continue to raise the jack slowly and
smoothly until the tyre clears the ground.
Do not raise the vehicle more than
necessary.

10-1

EMERGENCY SERVICE

844-74E-I

JUMP STARTING INSTRUCTIONS

w WARNING

843-10-001E

w WARNING
• Never get under the vehicle when it
is supported by the jack.
• Never run the engine when the
vehicle is supported by the jack and
never allow passengers to remain in
the vehicle.

843-10-003E

• Never attempt to jump start your
vehicle if the battery appears to be
frozen. Batteries in this condition
may explode or rupture if jump
starting is attempted.
• When
making
jump
lead
connections, be certain that your
hands and the jump leads remain
clear from pulleys, belts, or fans.
• Batteries produce flammable
hydrogen gas. Keep flames and
sparks away from the battery or an
explosion may occur. Never smoke
when working in the vicinity of the
battery.
• If the booster battery you use for
jump starting is installed in another
vehicle, make sure the two vehicles
are not touching each other.
• If
your
battery
discharges
repeatedly, for no apparent reason,
have your vehicle inspected by an
authorized MARUTI dealer.

10-2

EMERGENCY SERVICE

844-74E-I

3) Make jump lead connections as follows:

w WARNING
• To avoid harm to yourself or
damage to your vehicle or battery,
follow the jump starting instructions
below precisely and in order. If you
are in doubt, call for qualified road
service.

w CAUTION
• Vehicle equipped with electronic fuel
injection system will not start by
pushing or towing as the fuel pump
will not work in this condition. This
starting method could also result in
permanent damage to the catalytic
converter. Use jump leads to start
a vehicle with a weak or flat battery.

10-3

70F-08-004E

When jump starting your vehicle, use the
following procedure:
1) Use only a 12 volt battery to jump start
your vehicle. Position the good 12V
battery close to your vehicle so that the
jump leads will reach both batteries.
When using a battery installed on
another vehicle, DO NOT LET THE
VEHICLES TOUCH. Apply the parking
brakes fully on both vehicles.
2) Turn off all vehicle accessories, except
those necessary for safety reasons (for
example, headlights or hazard lights).

a) Connect one end of the first jump
lead to the positive (+) terminal of the
flat battery.
b) Connect the other end to the positive
(+) terminal of the booster battery.
c) Connect one end of the second jump
lead to the negative (-) terminal of
the booster battery.
d) Make the final connection to an
unpainted, heavy metal part of the
engine of the vehicle with the flat
battery.

w WARNING
Never connect the jump lead directly
to the negative (-) terminal of the
discharged battery, or an explosion
may occur.
4) If the booster battery you are using is
fitted to another vehicle, start the engine
of the vehicle with the booster battery.
Run the engine at moderate speed.
5) Start the engine of the vehicle with the
flat battery.
6) Remove the jump leads in the exact
reverse order in which you connected
them.
90

EMERGENCY SERVICE

844-74E-I

TOWING

EMERGENCY REMEDIES

If you need to have your vehicle towed,
contact a professional service.

If the Starter Does Not Operate:
1) Try turning the ignition switch to the
“START” position with the headlights
turned on to determine the battery
condition. If the headlights go excessively
dim or go off, it usually means that
either the battery is flat or the battery
terminal contact is poor. Recharge the
battery or correct battery terminal contact
as necessary.

w CAUTION
To help avoid damage to your vehicle
during towing, proper equipment and
towing procedures must be used.
Manual Transmission
Whenever possible, your vehicle should be
towed from the front with the front wheels
lifted. If the steering and drivetrain are in
good condition, your vehicle may be towed
from the rear with the rear wheels lifted and
the front wheels on the ground. Before
towing, make sure the steering is unlocked
and the transmission is in neutral.

2) If the headlights remain bright, check the
fuses. If the reason for failure of the
starter is not obvious, there may be a
major electrical problem. Have the
vehicle inspected by your authorized
MARUTI dealer.
If the Engine is Flooded
If the engine is flooded with petrol, it may
be hard to start. If this happens, press the
accelerator pedal all the way to the floor
and hold it there while cranking the engine.
(Do not operate the starter motor for more
than 15 seconds). Release the accelerator
as soon as the engine has started.

If the Engine Overheats
The engine could overheat temporarily under
severe driving conditions. If the engine
coolant temperature gauge indicates
overheating during driving:
1) Turn off the air conditioner, if equipped.
2) Take the vehicle to a safe place and
park.
3) Let the engine run at normal idle speed
for a few minutes until the indicator is
within
the
normal,
acceptable
temperature range between “H” and “C”.

w WARNING
If you see or hear escaping steam,
stop the vehicle in a safe place and
immediately turn off the engine to let
it cool. Do not open the bonnet when
steam is present. When the steam can
no longer be seen or heard, open the
hood to see if the coolant is still
boiling. If it is, you must wait until it
stops boiling before you proceed.

10-4

EMERGENCY SERVICE

844-74E-I

If the temperature indication does not come
down to within the normal, acceptable
range:
1) Turn off the engine and check that the
water pump belt and pulleys are not
damaged or slipping. If any abnormality
is found, correct it.
2) Check the coolant level in the reservoir.
If it is found to be lower than the “LOW”
line, look for leaks at the radiator, water
pump, and radiator and heater hoses. If
you locate any leaks that may have
caused the overheating, do not run the
engine until these problems have been
corrected.
3) If you do not find a leak, carefully add
coolant to the reservoir and then the
radiator, if necessary. (Refer to “ENGINE
COOLANT” in the “INSPECTION AND
MAINTENANCE” section.)

10-5

60G-09-039E

w WARNING

It is dangerous to remove the radiator
cap when the water temperature is
high, because scalding fluid and
steam may be blown out under
pressure. The cap should only be
taken
off when
the coolant
temperature has lowered.

To help prevent personal injury, keep
hands, tools and clothing away from
the engine cooling fan and airconditioner fan (if equipped). These
electric fans can automatically turn on
without warning.

844-74E-I

BODY WORK CARE

BODY WORK CARE
Corrosion Prevention ....................................................................................... 11-1
Vehicle Cleaning ............................................................................................... 11-2

BODY WORK CARE

844-74E-I

CORROSION PREVENTION
It is important to take good care of your
vehicle to protect it from corrosion.
Listed below are instructions for how to
maintain your vehicle to prevent corrosion.
Please read and follow these instructions
carefully.
Important Information About Corrosion
Common causes of corrosion
1) Accumulation of road salt, dirt, moisture,
or chemicals in hard to reach areas of
the vehicle underbody or frame.
2) Chipping, scratches and any damage to
treated or painted metal surfaces
resulting from minor accidents or
abrasion by stones and gravel.
Environmental
conditions
which
accelerate corrosion
1) Road salt, dust control chemicals, sea air
or industrial pollution will all accelerate
the corrosion of metal.
2) High humidity will increase the rate of
corrosion particularly when the
temperature range is just above the
freezing point.
3) Moisture in certain areas of a vehicle for
an extended period of time may promote
corrosion even though other body
sections may be completely dry.
4) High temperatures will cause an

11-1

accelerated rate of corrosion to parts of
the vehicle which are not well ventilated
to permit quick drying.
This information illustrates the necessity of
keeping your vehicle (particularly the
underbody) as clean and dry as possible.
It is equally important to repair any damage
to the paint or protective coatings as soon
as possible.
How to Help Prevent Corrosion
Wash your vehicle frequently
The best way to preserve the finish on your
vehicle and to help avoid corrosion is to
keep it clean with frequent washing.
Wash your vehicle regularly during the
winter and immediately after the winter.
Keep your vehicle, particularly the underside,
as clean and dry as possible.
If you frequently drive on salted roads, your
vehicle should be washed at least once a
month during the winter. If you live near the
ocean, your vehicle should be washed at
least once a month throughout the year.
For washing instructions, refer to the
“VEHICLE CLEANING” section.
Remove foreign material deposits
Foreign material such as salts, chemicals,
road oil or tar, tree sap, bird droppings and
industrial fall-out may damage the finish of
your vehicle if it is left on painted surfaces.

Remove these types of deposits as quickly
as possible. If these deposits are difficult to
wash off, an additional cleaner may be
required. Be sure that any cleaner you use
is not harmful to painted surfaces and is
specifically intended for your purposes.
Follow the manufacturer’s directions when
using these special cleaners.
Repair finish damage
Carefully examine your vehicle for damage
to the painted surfaces. Should you find any
chips or scratches in the paint, touch them
up immediately to prevent corrosion from
starting. If the chips or scratches have gone
through to the bare metal, have a qualified
body shop make the repair.
Keep
Passenger
and
luggage
compartments clean.
Moisture, dirt or mud can accumulate under
the floor mats and may cause corrosion.
Occasionally, check under these mats to
ensure that this area is clean and dry. More
frequent checks are necessary if the vehicle
is used off road or in wet weather.
Certain cargos such as chemicals, fertilizers,
cleaners, salts, etc., are extremely corrosive
by nature. These products should be
transported in sealed containers. If a spill
or leak does occur, clean and dry the area
immediately.
94

BODY WORK CARE

844-74E-I

VEHICLE CLEANING
Store your vehicle in a dry, wellventilated area.
Do not park your vehicle in a damp, poorly
ventilated area. If you often wash your
vehicle in the garage or if you frequently
drive it in when wet, your garage may be
damp. The high humidity in the garage may
cause or accelerate corrosion. A wet vehicle
may corrode even in a heated garage if the
ventilation is poor.

w WARNING
Do not apply additional undercoating
or rust preventive coating on or
around exhaust system components
such as the exhaust pipes, etc. A fire
could be started if the undercoating
substance becomes overheated.
Cover your vehicle
If you cannot regularly park your vehicle in
a garage, we recommend you use a vehicle
cover. Years of exposure to midday sun can
cause the colours in paint, plastic parts, and
fabrics to fade. Covering your vehicle with
a high-quality, “breathable” vehicle cover can
help protect the finish from the harmful UV
rays in sunlight, and can reduce the amount
of dust and air pollution reaching the
surface.
95

w WARNING
When cleaning the interior or exterior
of the vehicle, NEVER USE flammable
solvents such as lacquer thinners,
petrol, benzene or cleaning materials
such as bleach or strong household
detergents. The materials could cause
personal injury or damage to the
vehicle.
Cleaning the Interior
Vinyl upholstery
Prepare a solution of soap or mild detergent
mixed with warm water. Apply the solution
to the vinyl with a sponge or soft cloth and
let it soak for a few minutes to loosen dirt.
Rub the surface with a clean, damp cloth
to remove dirt and the soap solution. If
some dirt still remains on the surface, repeat
this procedure.
Fabric upholstery
Remove loose dirt with a vacuum cleaner.
Using a mild soap solution, rub stained
areas with a clean damp cloth. To remove
soap, rub the areas again with a cloth
dampened with water. Repeat this until the
stain is removed, or use a commercial fabric

cleaner for tougher stains. If you use a
fabric cleaner, carefully follow the
manufacturer’s instructions and precautions.
Seat Belts
Clean seat belts with a mild soap and
water. Do not use bleach or dye on the
belts. They may weaken the fabric in the
belts.
Vinyl floor mats
Ordinary dirt can be removed from vinyl with
water or mild soap. Use a brush to help
loosen dirt. After the dirt is loosened, rinse
the mat thoroughly with water and dry it in
the shade.
Carpets
Remove dirt and soil as much as possible
with a vacuum cleaner. Using a mild soap
solution, rub stained areas with a clean
damp cloth. To remove soap, rub the areas
again with a cloth dampened with water.
Repeat this until the stain is removed, or
use a commercial carpet cleaner for tougher
stains. If you use a carpet cleaner, carefully
follow the manufacturer’s instructions and
precautions.

11-2

BODY WORK CARE

Cleaning the Exterior

w CAUTION
It is important that your vehicle be
kept clean and free from dirt. Failure
to keep your vehicle clean may result
in fading of the paint or corrosion to
various parts of the vehicle body.
Washing

w WARNING
• Never attempt to wash and wax
your vehicle with the engine
running.
• When cleaning the underside of the
body and fender, where there may
be sharp-edged parts, you should
wear gloves and a longsleeved shirt
to protect your hands and arms
from being cut.
• After washing your vehicle, carefully
test the brakes before driving to
make sure they have maintained
their normal effectiveness.

11-3

844-74E-I

When washing the vehicle, follow the
instructions below:
1) Flush the underside of body and wheel
housings with pressurized water to
remove mud and debris. Use plenty of
water.

w CAUTION
When washing the vehicle, avoid
directing steam or hot water of more
than 800C (1760F) on plastic parts.
2) Remove dirt and mud from the body
exterior with running water. You may use
a soft sponge or brush. Do not use hard
materials which can scratch the paint.
3) Wash the entire exterior with a mild
detergent or car wash soap using a
sponge or soft cloth. The sponge or
cloth should be frequently soaked in the
soap solution.

w CAUTION
When using a commercial car wash
product, observe the cautions
specified by the manufacturer. Never
use strong household detergents or
soaps.

4) Once the dirt has been completely
removed, rinse off the detergent with
running water.
5) After rinsing, wipe off the vehicle body
with a wet chamois or cloth and allow
it to dry in the shade.
6) Check carefully for damage to painted
surfaces. If there is any damage,
“Touchup” the damage following the
procedure below:
a) Clean all damaged spots and allow
them to dry.
b) Stir the paint and “touchup” the
damaged spots lightly using a small
brush.
c) Allow the paint to dry completely.
Waxing
After washing the vehicle, waxing and
polishing are recommended to further
protect and beautify the paint.
• Only use waxes and polishes of good
quality.
• When using waxes and polishes,
observe the precautions specified by the
manufacturers.

844-74E-I

GENERAL INFORMATION

GENERAL INFORMATION
Vehicle Identification ....................................................................................... 12-1

GENERAL INFORMATION

844-74E-I

VEHICLE IDENTIFICATION

70F-10-001

843-12-001

Chassis Serial Number
The chassis and/or engine serial numbers
are used to register the vehicle. They are
also used to assist your dealer when
ordering or referring to special service
information. Whenever you have occasion to
consult your MARUTI dealer, remember to
identify your vehicle with this number.
Should you find the number difficult to read,
you will also find it on the identification
plate.

Engine Serial Number
The engine serial number is stamped on the
cylinder block as shown in the illustration
and also on the identification plate.

12-1

SPECIFICATIONS

844-74E-I

SPECIFICATIONS
NOTE:
Specifications are subject to change without notice.

DIMENSIONS
Overall length
Overall width
Overall height
Wheelbase
Tread

UNIT:mm
3
1
1
2
1
1

front
rear

Ground clearance
MASS (WEIGHT)
Kerb mass (weight)
Gross vehicle mass (weight) rating
Seating Capacity
ENGINE
Type
Number of cylinders
Bore
Stroke
Piston displacement
Compression ratio
99

335
440
405
175
215
200
170

UNIT:Kg
650 (Without A.C.)
665 (With A.C.)
1000
4 persons
F8D - Four-stroke cycle, 12 Valve, water cooled (SOHC)
3
68.5 mm
72.0 mm
796 cm3
9.2:1

SPECIFICATIONS

844-74E-I

ELECTRICAL
Standard spark plug
Battery
Fuses
Headlight
Turn signal light
Side turn signal light
Clearance light
Tail/brake light
Registration plate light
Reversing light

NGK – DCPR7E
38B20R (28AH/5HR)
See “INSPECTION AND MAINTENANCE” section
12V 60/55W
12V 21W
12V 5W
12V 5W
12V 5/21W
12V 5W
12V 21W

WHEEL AND SUSPENSION
Tyre size, front and rear
Tyre pressures front/rear
Suspension type
front
rear

145/70R12
1.9 kg/cm2
strut
Coil spring

STEERING
Toe-in

1± 2 mm

CAPACITIES
Coolant
(Including reservoir tank)
Fuel tank
Engine oil
Transmission oil

13-1

3.5 L
28 L
2.7 L (Replacement with Oil Filter)
2.1 L

100

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : Yes
Encryption                      : Standard V1.2 (40-bit)
User Access                     : Print, Fill forms, Extract, Assemble, Print high-res
Create Date                     : 2001:06:19 16:53:09
Producer                        : Acrobat Distiller 3.01 for Power Macintosh
Author                          : Sachin
Creator                         : PageMaker 6.5
Title                           : MB308-MPI
Modify Date                     : 2001:06:19 19:09:47
Page Count                      : 100

EXIF Metadata provided by EXIF.tools

MB308 MPI Maruti 800 Owners Manual Petrol

Navigation menu

Versions of this User Manual:

Views

Navigation