MiniDX3 User's Manual Mini DX3
User Manual:
Open the PDF directly: View PDF 
.
Page Count: 16
| Download | |
| Open PDF In Browser | View PDF |
Revision A 2010-01-06 MiniDX3 User’s Manual Rev. A Standard Package: a. MiniDX3 b. CD-ROM c. Chain Sling d. USB Cable -1- MiniDX3 User’s Manual Rev. A Connections Specifications ....................................................................................................................................3 Operational Description ....................................................................................................................5 Card Data Format..............................................................................................................................6 Communication Protocol ..................................................................................................................7 FCC COMPLIANCE STATEMENT This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communication. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. -2- MiniDX3 User’s Manual Rev. A Specifications Magnetic Stripe Card : TRACK 1 / IATA / 210 bpi / 79 Alphanumeric Characters TRACK 2 / ABA / 75 bpi / 40 Numeric Characters TRACK 3 / Thrift / 210 bpi / 107 Numeric Characters RS232 Interface : RS232 , Half-Duplex , 8N1 , 9600 bps USB Interface Full compliance with the USB Specification V 1.1 The device uses a Virtual Serial Port Driver, making it appear to have the software like a standard RS232 Serial Port. CLOCK : Real Time Clock (RTC) module and back-up capacitor Memory Size for Storing Data : CMOS Serial Flash Memory 512K bytes Up to 2048 records ( 256 Bytes / Record ) Battery Power : Rechargeable Lithium-ion Polymer Battery Nominal Capacity: 250 mAH ( Typical ) Nominal Voltage: 3.7 V Cycle Life: 300 cycles ( at least ) Low Battery Detect and Built-in Quick Charge Circuit Power Supply for Charge : DC 5V , 200mA ( for RS-232 ) or USB Powered Charging duration time : 1.5 ~ 2.5 hr Working duration time after charge : 48 hr ( always power on ) Environment : Operating Temp : -0℃ ~ +60℃ ( Discharge ) -0℃ ~ +45℃ ( Charging ) Storage Temp : -10 ~ +65℃ Humidity : 10 ~ 90 % relative Dimensions : L 50 x W 23.5 x H 32.5 mm Mounting : Portable or Any surface -3- MiniDX3 User’s Manual Rev. A Display Information Operational Indicator Battery Indicator -4- MiniDX3 User’s Manual Rev. A Operational Description 1. Powered by Battery For normal use, the unit is powered by battery. Push the Power Switch Button for about 1.5 seconds to turn on the unit. Also push the Power Switch Button for about 1.5 seconds to turn off the unit. After the unit is turned on, the power would be turned off automatically if there is no swiping a card on the unit in 30 seconds. This means the unit would be turned off if no swiping a card again in every 30 seconds after every card swiping. It would have Low Battery Detect/Warning indication when the unit is powered by battery. 2. Powered by Cable When the unit is connected with the PC through the communication Cable and the PC is running MiniDX3 software and open the COM PORT for the unit, then the unit will be turned on in about 0.5 second by the PC through the RS-232 COM PORT. Then you can do the unit Setting, Configuration or data downloading. When the software closes the COM PORT or exits, the power turn off from the PC immediately. When powered by cable from PC, the Power Switch would have no function and the unit would have no Low Battery Detect/Warning function. 3. Real Time Clock Setting Before start using the unit, you must set the Real Time Clock (RTC) inside the unit to your local time. If there is no battery for quite a while or it is powered by cable for quite a while this would cause Real Time clock (RTC) malfunctioned due to no power supply. When put on the battery to turn on the unit and the Red/Green LED take turns blinking, this means the RTC is malfunctioning and you must do the RTC time setting before you use the unit. 4. Low Battery Detect When powered by battery, it would have Low Battery Detect function. When the battery goes low, the LED would flash green once every 2 second and you must charge battery immediately, otherwise, the unit would shut down any time without pre-warning. 5. Charge Mode There are three different charge modes for MiniDX3: low battery mode, real time mode and manual charge mode. Low battery charge mode is used when the battery hits low voltage, it starts to be charged automatically. Real time charge mode is whenever the MiniDX3 cable is connected to USB or Power adapter, it would be charged immediately. Manual charge mode is the charge is controlled by Demo software . User can use the software to start or stop charging. 6. Charge Status Indication When MiniDX3 is in charge, Battery Status Indicator light show slow blink red that means the battery is in the pre-charge. When Battery Status Indicator light turns to red, it means the battery is in charge status. When Battery Status Indicator light turns to green, it means the charge is finished. If the charge process has unusual situation, Battery Status Indicator light will show red fast blink. If MiniDX3 cable is connected, and battery is not in charge, Battery Status Indicator light will turn off. The default set mode is on low battery charge mode. 7. Memory Low Warning Log database memory is almost full (>90%). Adding new records is still possible but you are advised to free up the log database memory by uploading the data to the PC as soon as possible. 8. Memory Full Warning Log database memory is full. You not be able to add any new records. Free the log database memory by uploading the data to the PC. 9. Firmware Management mode (FMM) FMM allows you to quickly upgrade your MiniDX3's internal firmware via com port and also check validity of currently loaded firmware. Contact your dealer for most recent firmware upgrade files. -5- MiniDX3 User’s Manual Rev. A Card Data Format -6- MiniDX3 User’s Manual Rev. A Communication Protocol Packet Format -7- MiniDX3 User’s Manual Rev. A -8- MiniDX3 User’s Manual Rev. A -9- MiniDX3 User’s Manual Rev. A - 10 - MiniDX3 User’s Manual Rev. A - 11 - MiniDX3 User’s Manual Rev. A - 12 - MiniDX3 User’s Manual Rev. A - 13 - MiniDX3 User’s Manual Rev. A - 14 - MiniDX3 User’s Manual Rev. A - 15 -
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Page Count : 16 XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:71f4eaff-cacf-4448-9834-fa6f83ee9af3 Producer : Acrobat Distiller 6.0 (Windows) Company : 微软中国 Source Modified : D:20100123172612 Headline : Create Date : 2010:01:24 01:26:22+08:00 Creator Tool : Acrobat PDFMaker 6.0 for Word Modify Date : 2010:01:24 01:26:47+08:00 Metadata Date : 2010:01:24 01:26:47+08:00 Document ID : uuid:62e4dd31-bcd2-498f-b7d7-9f2585181bda Version ID : 16 Format : application/pdf Title : Microsoft Word - MiniDX3 User's manual.doc Creator : 微软用户 Subject : Tagged PDF : Yes Author : 微软用户EXIF Metadata provided by EXIF.tools