Release Notes For The Industrial Ethernet 3010 Switch, Cisco IOS 15.2E IE3010 OL32540
User Manual: IE3010
Open the PDF directly: View PDF 
.
Page Count: 16
| Download | |
| Open PDF In Browser | View PDF |
Release Notes for the Industrial Ethernet 3010
Switch, Cisco IOS Release 15.2(2)E
January 10, 2017
Cisco IOS Release 15.2(2)E runs on all Cisco IE 3010 switches.
These release notes include important information about Cisco IOS release 15.2(2)E, and any
limitations, restrictions, and caveats that apply to it. Verify that these release notes are correct for your
switch:
•
If you are installing a new switch, see the Cisco IOS release label on your switch rear panel.
•
If your switch is on, use the show version privileged EXEC command. See the “Finding the
Software Version and Feature Set” section on page 4.
•
If you are upgrading to a new release, see the software upgrade filename for the software version.
See the “Deciding Which Files to Use” section on page 4.
You can download the switch software from this site (registered Cisco.com users with a login password):
http://www.cisco.com/cisco/web/download/index.html
Contents
•
System Requirements, page 2
•
Upgrading the Switch Software, page 3
•
Installation Notes, page 6
•
New Software Features, page 6
•
Limitations and Restrictions, page 7
•
Important Notes, page 11
•
Caveats, page 12
•
Related Documentation, page 14
•
Obtaining Documentation, Obtaining Support, and Security Guidelines, page 16
Americas Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
© 2012–2017 Cisco Systems, Inc. All rights reserved.
System Requirements
System Requirements
•
Hardware Supported, page 2
•
Express Setup Requirements, page 3
•
Upgrading the Switch Software, page 3
Hardware Supported
.
Table 1
Supported by Minimum
Cisco IOS Release
Switch Model
Description
Cisco IE-3010-24TC
Cisco IOS Release 15.0(2)SE
24 10/100 FastEthernet ports, 2 dual-purpose
ports (2 10/100/1000BASE-T copper ports and 2
SFP1 module slots), and 2 AC- and
DC-power-supply module slots.
Cisco IE-3010-16S-8PC
16 100BASE-FX SFP-module slots; 8 10/100
FastEthernet PoE2 ports, 2 dual-purpose ports (2
10/100/1000BASE-T copper ports and 2 SFP
module slots), and 2 AC- and DC-power-supply
module slots.
Cisco IOS Release 15.0(2)SE
Rugged and industrial SFP modules3
GLC-SX-MM-RGD
Cisco IOS Release 15.0(2)SE
GLC-LX-SM-RGD
GLC-FE-100LX-RGD
GLC-FE-100FX-RGD
GLC-ZX-SM-RGD
Commercial SFP modules
GLC-BX-D with digital optical monitoring
(DOM) support
Cisco IOS Release 15.0(2)SE
BLC-BX-U with DOM support
GLC-FE-100LX
GLC-FE-100BX-D
GLC-FE-100BX-U
GLC-FE-100FX
GLC-FE-100EX
GLC-FE-100ZX
CWDM SFP with DOM support
Extended temperature SFP modules
SFP-GE-L with DOM support
Cisco IOS Release 15.0(2)SE
SFP-GE-S with DOM support
SFP-GE-Z with DOM support
GLC-EX-SMD with DOM support
Release Notes for the Industrial Ethernet 3010 Switch, Cisco IOS Release 15.2(2)E
2
OL-32540-02
Upgrading the Switch Software
Table 1
Switch Model
Description
Supported by Minimum
Cisco IOS Release
SFP module patch cable
CAB-SFP-50CM
Cisco IOS Release 15.0(2)SE
Power supply modules
PWR-RGD-AC-DC/IA
PWR-RGD-LOW-DC/IA
Cisco IOS Release 15.0(2)SE
Note
For power supply module descriptions
and supported configurations on switch
models, see the hardware installation
guide.
1. SFP = small form-factor pluggable.
2. PoE = Power over Ethernet.
3. The maximum operating temperature of the switch varies depending on the type of SFP module that you use.
See the Cisco IE 3010 Switch Hardware Installation Guide for more information.
Express Setup Requirements
Hardware
Table 2
Minimum Hardware Requirements
Processor Speed
233 MHz minimum
DRAM
1
512 MB
2
Number of
Colors
Resolution
Font Size
256
1024 x 768
Small
1. We recommend 1 GHz.
2. We recommend 1 GB DRAM.
Software
•
Windows 2000, XP, Vista, Windows 7, and Windows Server 2003.
•
Internet Explorer 6.0, 7.0, Firefox up to version 26.0 with JavaScript enabled.
Express Setup verifies the browser version when starting a session, and it does not require a plug-in.
Upgrading the Switch Software
•
Finding the Software Version and Feature Set, page 4
•
Deciding Which Files to Use, page 4
•
Archiving Software Images, page 4
•
Upgrading a Switch by Using the CLI, page 5
•
Recovering from a Software Failure, page 6
Release Notes for the Industrial Ethernet 3010 Switch, Cisco IOS Release 15.2(2)E
OL-32540-02
3
Upgrading the Switch Software
Finding the Software Version and Feature Set
The Cisco IOS image is stored as a bin file in a directory that is named with the Cisco IOS release. A
subdirectory contains the files needed for web management. The image is stored on the compact flash
memory card.
You can use the show version privileged EXEC command to see the software version that is running on
your switch. The second line of the display shows the version.
You can also use the dir filesystem: privileged EXEC command to see the directory names of other
software images that you might have stored in flash memory.
Deciding Which Files to Use
The upgrade procedures in these release notes describe how to perform the upgrade by using a combined
tar file. This file contains the Cisco IOS image file and the files needed for the embedded Express Setup.
You must use the combined tar file to upgrade the switch through Express Setup. To upgrade the switch
through the CLI, use the tar file and the archive download-sw privileged EXEC command.
Table 3
Cisco IOS Software Image File
Filename
Description
ie3010-ipservicesk9-mz.152-2.E.bin
ie3010-ipservicesk9-tar.152-2.E.tar
1
ie3010-lanbasek9-mz.152-2.E.bin
ie3010-lanbasek9-tar.152-2.E.tar
Cisco IE 3010 IP Services cryptographic image with Layer 2 and Layer 3
features.
Cisco IE 3010 LAN Base cryptographic image with all Layer 2 features, IPv4
static routing, and inter-VLAN routing.
1. The ie3010-ipservicesk9-tar.152.2.E.tar image is greater than 32MB, and you cannot have more than one image file on the flash.
Archiving Software Images
Before upgrading your switch software, make sure that you have archived copies of the current
Cisco IOS release and the Cisco IOS release to which you are upgrading. You should keep these archived
images until you have upgraded all devices in the network to the new Cisco IOS image and until you
have verified that the new Cisco IOS image works properly in your network.
Cisco routinely removes old Cisco IOS versions from Cisco.com. See Product Bulletin 2863 for more
information:
http://www.cisco.com/en/US/prod/collateral/iosswrel/ps8802/ps6969/ps1835/
prod_bulletin0900aecd80281c0e.html
You can copy the bin software image file on the flash memory to the appropriate TFTP directory on a
host by using the copy flash: tftp: privileged EXEC command.
Note
Although you can copy any file on the flash memory to the TFTP server, it is time-consuming to copy
all of the HTML files in the tar file. We recommend that you download the tar file from Cisco.com and
archive it on an internal host in your network.
Release Notes for the Industrial Ethernet 3010 Switch, Cisco IOS Release 15.2(2)E
4
OL-32540-02
Upgrading the Switch Software
You can also configure the switch as a TFTP server to copy files from one switch to another without
using an external TFTP server by using the tftp-server global configuration command. For more
information about the tftp-server command, see the “Basic File Transfer Services Commands” section
of the Cisco IOS Configuration Fundamentals Command Reference, Release 12.2:
http://www.cisco.com/en/US/docs/ios/fundamentals/command/reference/cf_t1.html
Upgrading a Switch by Using the CLI
This procedure is for copying the combined tar file to the switch. You copy the file to the switch from a
TFTP server and extract the files. You can download an image file and replace or keep the current image.
Note
Make sure that the compact flash card is inserted into the switch before downloading the software.
To download software, follow these steps:
Step 1
Use Table 3 on page 4 to identify the file that you want to download.
Step 2
Download the software image file. If you have a SmartNet support contract, go to this URL, and log in
to download the appropriate files:
http://www.cisco.com/cisco/web/download/index.html
To download the image for an IE 3010 switch, click Switches > Industrial Ethernet Switches >
Cisco IE 3010 Series Switches, and then click on the Cisco IOS software for your specific switch
model.
Step 3
Copy the image to the appropriate TFTP directory on the workstation, and make sure that the TFTP
server is properly configured.
For more information, see Appendix B of the software configuration guide for this release.
Step 4
Log into the switch through the console port or a Telnet session.
Step 5
(Optional) Check that you have IP connectivity to the TFTP server by entering this privileged EXEC
command:
Switch# ping tftp-server-address
For more information about assigning an IP address and default gateway to the switch, see the software
configuration guide for this release.
Step 6
Download the image file from the TFTP server to the switch. If you are installing the same version of
software that is currently on the switch, overwrite the current image by entering this privileged EXEC
command:
Switch# archive download-sw /overwrite /reload tftp:[[//location]/directory]/
image-name.tar
The /overwrite option overwrites the software image in flash memory with the downloaded one.
The /reload option reloads the system after downloading the image unless the configuration has been
changed and not saved.
For //location, specify the IP address of the TFTP server.
For /directory/image-name.tar, specify the directory (optional) and the image to download. Directory
and image names are case sensitive.
Release Notes for the Industrial Ethernet 3010 Switch, Cisco IOS Release 15.2(2)E
OL-32540-02
5
Installation Notes
This example shows how to download an image from a TFTP server at 198.30.20.19 and to overwrite
the image on the switch:
Switch# archive download-sw /overwrite tftp://198.30.20.19/image-name.tar
You can also download the image file from the TFTP server to the switch and keep the current image by
replacing the /overwrite option with the /leave-old-sw option.
Recovering from a Software Failure
For additional recovery procedures, see the “Troubleshooting” chapter in the software configuration
guide for this release.
Installation Notes
You can assign IP information to your switch by using these methods:
•
The Express Setup program, as described in the switch getting started guide.
•
The CLI-based setup program, as described in the switch hardware installation guide.
•
The DHCP-based autoconfiguration, as described in the switch software configuration guide.
•
Manually assigning an IP address, as described in the switch software configuration guide.
New Software Features
•
Features Introduced in Cisco IOS Release 15.2(2)E1, page 6
•
Features Introduced in Cisco IOS Release 15.2(2)E, page 7
Features Introduced in Cisco IOS Release 15.2(2)E1
What’s New
Description
Device Sensor
(LAN Base)
Release Notes for the Industrial Ethernet 3010 Switch, Cisco IOS Release 15.2(2)E
6
OL-32540-02
Limitations and Restrictions
Features Introduced in Cisco IOS Release 15.2(2)E
What’s New
Description
Cisco IOS Release 15E
Documentation Roadmap
Provides quick and easy access to all relevant documentation for specific platforms.
Look for Quick Links to Platform Documentation on the respective platform
documentation pages.
Integrated Documentation Guides
Provides platform and software documentation for two technologies:
•
IP Multicast Routing Configuration Guide
•
Cisco Flexible Netflow Configuration Guide.
Smart Install
Smart Install is a plug-and-play configuration and image-management feature that
provides zero-touch deployment for new switches. You can ship a switch to a location,
place it in the network and power it on with no configuration required on the device. The
IE 3010 switch can be a Smart Install Director. For more information, see Smart Install
Configuration Guide here: http://www.cisco.com/c/en/us/td/docs/switches/lan/
smart_install/configuration/guide/smart_install.html
Cisco EnergyWise
Support for Cisco EnergyWise Version 2.8. For more information, see the Cisco
EnergyWise software release notes and configuration guide. For more information, see
the Cisco EnergyWise software release notes and the configuration guide here: http://
www.cisco.com/c/en/us/td/docs/switches/lan/energywise/version2_8/ios/release/notes/
ol23554.html
IP Device Tracking
Enhancement to IP device tracking for ARP probes; command now supports new
keyword ip device tracking probe auto-source fallback 0.0.0.100 255.255.255.0
override.
Plug-N-Play
Cisco Open Plug-n-Play agent is a software application that is running on a Cisco IOS
or IOS-XE device and provides zero-touch deployment of all new devices. The
application facilitates the acquisition and loading of pertinent images, configuration
files, and other required files to the device along with notifications for various events.
(Cisco IE 3010 only supports Cisco IOS)
For the Software Configuration Guide, Cisco IOS Release 15.2(2)E (Industrial Ethernet 3010 Switch),
go to http://www.cisco.com/c/en/us/td/docs/switches/lan/cisco_ie3010/software/release/15-2_2_e/
configuration/guide/SwCfg.html.
Limitations and Restrictions
You should review this section before you begin working with the switch. These are known limitations
that will not be fixed, and there is not always a workaround. Some features might not work as
documented, and some features could be affected by recent changes to the switch hardware or software.
•
Cisco IOS Limitations, page 7
•
Express Setup Notes, page 11
Cisco IOS Limitations
•
Configuration, page 8
Release Notes for the Industrial Ethernet 3010 Switch, Cisco IOS Release 15.2(2)E
OL-32540-02
7
Limitations and Restrictions
•
Ethernet, page 9
•
IP, page 9
•
QoS, page 9
•
SPAN and RSPAN, page 10
•
Trunking, page 10
•
VLAN, page 10
•
A static IP address might be removed when the previously acquired DHCP IP address lease expires.
Configuration
This problem occurs under these conditions:
– When the switch is started without a configuration (no config.text file in flash memory).
– When the switch is connected to a DHCP server that is configured to give the switch an address.
(The dynamic IP address is assigned to VLAN 1).
– When an IP address is configured on VLAN 1 before the dynamic address lease assigned to
VLAN 1 expires.
The workaround is to reconfigure the static IP address. (CSCea71176 and CSCdz11708)
•
When connected to some third-party devices that send early preambles, a switch port operating at
100 Mb/s full duplex or 100 Mb/s half duplex might bounce the line protocol up and down. The
problem is observed only when the switch is receiving frames.
The workaround is to configure the port for 10 Mb/s and half duplex or to connect a hub or a
nonaffected device to the switch. (CSCed39091)
•
When port security is enabled on an interface in restricted mode and the switchport block unicast
interface command has been entered on that interface, MAC addresses are incorrectly forwarded
when they should be blocked
The workaround is to enter the no switchport block unicast interface configuration command on
that specific interface. (CSCee93822)
•
A traceback error occurs if a crypto key is generated after an SSL client session.
There is no workaround. This is a cosmetic error and does not affect the functionality of the switch.
(CSCef59331)
•
When the logging event-spanning-tree interface configuration command is configured and logging
to the console is enabled, a topology change might generate a large number of logging messages,
causing high CPU usage. CPU usage can increase with the number of spanning-tree instances and
the number of interfaces configured with the logging event-spanning-tree interface configuration
command. This condition adversely affects how the switch operates and could cause problems such
as STP convergence delay.
High CPU usage can also occur with other conditions, such as when debug messages are logged at
a high rate to the console.
Use one of these workarounds:
– Disable logging to the console.
– Rate-limit logging messages to the console.
– Remove the logging event spanning-tree interface configuration command from the interfaces.
(CSCsg91027)
Release Notes for the Industrial Ethernet 3010 Switch, Cisco IOS Release 15.2(2)E
8
OL-32540-02
Limitations and Restrictions
•
The far-end fault optional facility is not supported on the GLC-GE-100FX SFP module.
The workaround is to configure aggressive UDLD. (CSCsh70244)
•
When you enter the boot host retry timeout global configuration command to specify the amount
of time that the client should keep trying to download the configuration and you do not enter a
timeout value, the default value is zero, which should mean that the client keeps trying indefinitely.
However, the client does not keep trying to download the configuration.
The workaround is to always enter a non-zero value for the timeout value when you enter the boot
host retry timeout timeout-value command. (CSCsk65142)
•
On a switch running both Resilient Ethernet Protocol (REP) and Bidirectional Forwarding Detection
(BFD), when the REP link status layer (LSL) age-out value is less than 1 second, the REP link flaps
if the BFD interface is shut down and then brought back up.
The workaround is to use the rep lsl-age-out timer interface configuration command to configure
the REP LSL age timer for more than 1000 milliseconds (1 second). (CSCsz40613)
Ethernet
Traffic on EtherChannel ports is not perfectly load-balanced. Egress traffic on EtherChannel ports is
distributed to member ports on a load-balance configuration, and traffic characteristics such as MAC or
IP address.
More than one traffic stream might map to same member ports based on hashing results calculated by
the ASIC. If this happens, uneven traffic distribution happens on EtherChannel ports.
Changing the load-balance distribution method or changing the number of ports in the EtherChannel can
resolve this problem.
Use any of these workarounds to improve EtherChannel load balancing:
•
For random source-ip and dest-ip traffic, configure the load-balance method as src-dst-ip.
•
For incrementing source-ip traffic, configure the load-balance method as src-ip.
•
For incrementing dest-ip traffic, configure the load-balance method as dst-ip.
•
Configure the number of ports in the EtherChannel so that the number is equal to a power of 2 (that
is, 2, 4, or 8)
For example, with load balance configured as dst-ip with 150 distinct incrementing destination IP
addresses, and the number of ports in the EtherChannel set to either 2, 4, or 8, load distribution is
optimal. (CSCeh81991)
IP
When the rate of received DHCP requests exceeds 2,000 packets per minute for a long time, the response
time might be slow when you are using the console.
The workaround is to use rate limiting on DHCP traffic to prevent a denial of service attack from
occurring. (CSCeb59166)
QoS
•
Some switch queues are disabled if the buffer size or threshold level is set too low with the mls qos
queue-set output global configuration command. The ratio of buffer size to threshold level should
be greater than 10 to avoid disabling the queue.
Release Notes for the Industrial Ethernet 3010 Switch, Cisco IOS Release 15.2(2)E
OL-32540-02
9
Limitations and Restrictions
The workaround is to choose compatible buffer sizes and threshold levels. (CSCea76893)
•
When auto-QoS is enabled on the switch, priority queuing is not enabled. Instead, the switch uses
shaped round robin (SRR) as the queuing method. The auto-QoS feature is designed on each
platform based on the feature set and hardware limitations, and the queuing method supported on
each platform might be different.
There is no workaround. (CSCee22591)
SPAN and RSPAN
•
Cisco Discovery Protocol (CDP), VLAN Trunking Protocol (VTP), and Port Aggregation Protocol
(PAgP) packets received from a SPAN source are not sent to the destination interfaces of a local
SPAN session.
The workaround is to use the monitor session session_number destination {interface interface-id
encapsulation replicate} global configuration command for local SPAN. (CSCed24036)
Trunking
•
IP traffic with IP options set is sometimes leaked on a trunk port. For example, a trunk port is a
member of an IP multicast group in VLAN X but is not a member in VLAN Y. If VLAN Y is the
output interface for the multicast route entry assigned to the multicast group and an interface in
VLAN Y belongs to the same multicast group, the IP-option traffic received on an input VLAN
interface other than the one in VLAN Y is sent on the trunk port in VLAN Y because the trunk port
is forwarding in VLAN Y, even though the port has no group membership in VLAN Y.
There is no workaround. (CSCdz42909).
•
For trunk ports or access ports configured with IEEE 802.1Q tagging, inconsistent statistics might
appear in the show interfaces counters privileged EXEC command output. Valid IEEE 802.1Q
frames of 64 to 66 bytes are correctly forwarded even though the port LED blinks amber, and the
frames are not counted on the interface statistics.
There is no workaround. (CSCec35100).
VLAN
•
If the number of VLANs times the number of trunk ports exceeds the recommended limit of 13,000,
the switch can fail.
The workaround is to reduce the number of VLANs or trunks. (CSCeb31087)
•
When line rate traffic is passing through a dynamic port, and you enter the switchport access vlan
dynamic interface configuration command for a range of ports, the VLANs might not be correctly
assigned. One or more VLANs with a null ID appears in the MAC address table instead.
The workaround is to enter the switchport access vlan dynamic interface configuration command
separately on each port. (CSCsi26392)
Release Notes for the Industrial Ethernet 3010 Switch, Cisco IOS Release 15.2(2)E
10
OL-32540-02
Important Notes
Important Notes
Express Setup Notes
•
•
We recommend using this browser setting to speed up the time needed to display Express Setup from
Microsoft Internet Explorer.
1.
Choose Tools > Internet Options.
2.
Click Settings in the Temporary Internet files area.
3.
From the Settings window, choose Automatically.
4.
Click OK.
5.
Click OK to exit the Internet Options window.
The HTTP server interface must be enabled to display Express Setup. By default, the HTTP server
is enabled on the switch. Use the show running-config privileged EXEC command to see if the
HTTP server is enabled or disabled.
Beginning in privileged EXEC mode, follow these steps to configure the HTTP server interface:
Command
Purpose
Step 1
configure terminal
Enters global configuration mode.
Step 2
ip http authentication {aaa | enable |
local}
Configures the HTTP server interface for the type of authentication that
you want to use.
•
aaa—Enables the authentication, authorization, and accounting
feature. You must enter the aaa new-model interface configuration
command for the aaa keyword to appear.
•
enable—Enables the password, which is the default method of
HTTP server user authentication, is used.
•
local—Local user database, as defined on the Cisco router or access
server, is used.
Step 3
end
Returns to privileged EXEC mode.
Step 4
show running-config
Verifies your entries.
•
Express Setup uses the HTTP protocol (the default is port 80) and the default method of
authentication (the enable password) to communicate with the switch through any of its Ethernet
ports and to allow switch management from a standard web browser.
If you change the HTTP port, you must include the new port number when you enter the IP address
in the browser Location or Address field (for example, http://10.1.126.45:184, where 184 is the
new HTTP port number). Write down the port number through which you are connected. Use care
when changing the switch IP information.
If you are not using the default method of authentication (the enable password), you need to
configure the HTTP server interface with the method of authentication used on the switch.
Release Notes for the Industrial Ethernet 3010 Switch, Cisco IOS Release 15.2(2)E
OL-32540-02
11
Caveats
Beginning in privileged EXEC mode, follow these steps to configure the HTTP server interface:
Command
Purpose
Step 1
configure terminal
Enters global configuration mode.
Step 2
ip http authentication {enable | local |
tacacs}
Configures the HTTP server interface for the type of authentication that
you want to use.
•
enable—Enables the password, which is the default method of
HTTP server user authentication, is used.
•
local—Local user database, as defined on the Cisco router or access
server, is used.
•
tacacs—TACACS server is used.
Step 3
end
Returns to privileged EXEC mode.
Step 4
show running-config
Verifies your entries.
Caveats
•
Cisco Bug Search Tool, page 12
•
Open Caveats, page 13
•
Caveats Resolved in Cisco IOS Release 15.2(2)E6, page 13
•
Caveats Resolved in Cisco IOS Release 15.2(2)E5a, page 13
•
Caveats Resolved in Cisco IOS Release 15.2(2)E5, page 13
•
Caveats Resolved in Cisco IOS Release 15.2(2)E4, page 13
•
Caveats Resolved in Cisco IOS Release 15.2(2)E3, page 13
•
Caveats Resolved in Cisco IOS Release 15.2(2)E2, page 14
•
Caveats Resolved in Cisco IOS Release 15.2(2)E1, page 14
•
Caveats Resolved in Cisco IOS Release 15.2(2)E, page 14
Cisco Bug Search Tool
The Bug Search Tool (BST), which is the online successor to Bug Toolkit, is designed to improve the
effectiveness in network risk management and device troubleshooting. The BST allows partners and
customers to search for software bugs based on product, release, and keyword, and aggregates key data
such as bug details, product, and version. The tool has a provision to filter bugs based on credentials to
provide external and internal bug views for the search input.
To view the details of a caveat listed in this document:
1.
Access the BST (use your Cisco user ID and password) at https://tools.cisco.com/bugsearch/.
2.
Enter the bug ID in the Search For: field.
Release Notes for the Industrial Ethernet 3010 Switch, Cisco IOS Release 15.2(2)E
12
OL-32540-02
Caveats
Open Caveats
No Open Caveats.
Caveats Resolved in Cisco IOS Release 15.2(2)E6
No caveats were resolved in this release.
Caveats Resolved in Cisco IOS Release 15.2(2)E5a
Bug ID
Severity
Headline
CSCvb19326
2
NTP leap second addition is not working during leap second event
Caveats Resolved in Cisco IOS Release 15.2(2)E5
Bug ID
Severity
Headline
CSCut86361
3
3010, 2520 Temperature & Power monitor SNMP status report incorrectly
Caveats Resolved in Cisco IOS Release 15.2(2)E4
No caveats were resolved in this release.
Caveats Resolved in Cisco IOS Release 15.2(2)E3
Bug ID
Severity
Headline
CSCul73513
2
Server-client clock not in sync after leap configuration
CSCum17258
2
EPM_SESS_ERR: Error in activating feature (EPM ACL PLUG-IN)
CSCup81878
2
Line by Line Sync fails while deleting dynamic NTP peer
CSCur11439
3
EnergyWise Activitycheck powers off phone during an active call
CSCur58372
3
"snmp-server enable traps syslog" shows in "show run all" output after removal
CSCur59242
2
Crash due to tplus_client_stop_timer
CSCus09761
2
IOS-Phone not placed in critical voice VLAN when AAA server is unreached
CSCus13924
2
Device crashes while configuring 'Identity' commands
CSCus47009
3
Switch does not increment the "Received on untrusted ports" DHCP counter
CSCus79132
2
Dot1x authentication legacy behavior broken
CSCut10251
2
Some commands are not in running-config after AUTOINSTALL finishes
CSCut13064
3
BPDU filter does not work on output port when STP is disabled
CSCut20271
2
C3560X responds to ARP request from management port
Release Notes for the Industrial Ethernet 3010 Switch, Cisco IOS Release 15.2(2)E
OL-32540-02
13
Related Documentation
Bug ID
Severity
Headline
CSCut27272
2
CPUHOG and crash due to Auth Manager process
CSCut79680
3
ip default-gateway is not seen in running-config after AUTOINSTALL
CSCut87425
2
CPU hog in "EEM TCL Proc" after TCL script termination with long runtime
CSCuu50392
2
Auth Manager memory leak with ISE authentication
CSCuu97116
2
Acct messages should include Class attribute from authentication
CSCuv06451
2
IOSd crash in eap_auth_terminal_state calling free_internal
Caveats Resolved in Cisco IOS Release 15.2(2)E2
No caveats were resolved in this release
Caveats Resolved in Cisco IOS Release 15.2(2)E1
Bug ID
Severity
Headline
CSCun68507
1
IE3K Bad CF card (bzip not handling corrupted image data correctly)
CSCun80959
2
Desg port on the RootBridge experienced block forward for 30 sec
CSCuo25980
2
EA branches must fix: tftp from CNA crash IE switches
CSCup96299
2
IPv6 Multicast RIB entry refer to wrong distance
CSCuq10827
3
C3560X cHsrpGrpStandbyState is incorrect
CSCur00722
1
Hard Reset of the Active Sup cause switch to power cycle
Caveats Resolved in Cisco IOS Release 15.2(2)E
Bug ID
Severity
Headline
CSCum65206
3
VLAN-based QoS support to be enabled for IE3000/IE3010 platforms
CSCum76147
3
No warning for Port Security Settings changes displayed via Device Mgr
Related Documentation
These documents provide complete information about the Cisco IE 3010 switches and are available at
Cisco.com:
http://www.cisco.com/en/US/products/ps11245/tsd_products_support_series_home.html
•
Cisco IE 3010 Switch Software Configuration Guide
•
Cisco IE 3010 Switch Command Reference
•
Cisco IE 3010 Switch System Message Guide
•
Cisco IE 3010 Switch Hardware Installation Guide
Release Notes for the Industrial Ethernet 3010 Switch, Cisco IOS Release 15.2(2)E
14
OL-32540-02
Related Documentation
•
Cisco IE 3010 Switch Getting Started Guide—available in English, simplified Chinese, French,
German, Italian, Japanese, Brazilian Portuguese, and Spanish
•
Regulatory Compliance and Safety Information for the Cisco IE 3010 Switch
For other information about related products, see these documents:
•
Express Setup online help (available on the switch)
These SFP module installation notes are available from Cisco.com:
http://www.cisco.com/en/US/products/hw/modules/ps5455/prod_installation_guides_list.html
•
Cisco Small Form-Factor Pluggable Modules Installation Notes
•
Cisco CWDM GBIC and CWDM SFP Installation Note
Compatibility matrix documents:
http://www.cisco.com/en/US/products/hw/modules/ps5455/products_device_support_tables_list.html
•
Cisco Small Form-Factor Pluggable Modules Compatibility Matrix
•
Compatibility Matrix for 1000BASE-T Small Form-Factor Pluggable Modules
Release Notes for the Industrial Ethernet 3010 Switch, Cisco IOS Release 15.2(2)E
OL-32540-02
15
Obtaining Documentation, Obtaining Support, and Security Guidelines
Obtaining Documentation, Obtaining Support, and Security
Guidelines
For information on obtaining documentation, submitting a service request, and gathering additional
information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and
revised Cisco technical documentation, at:
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html
Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed
and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free
service and Cisco currently supports RSS version 2.0.
This document is to be used in conjunction with the documents listed in the “Related Documentation” section.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of
Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The
use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)
© 2014–2017 Cisco Systems, Inc. All rights reserved.
Release Notes for the Industrial Ethernet 3010 Switch, Cisco IOS Release 15.2(2)E
16
OL-32540-02
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Language : en Page Mode : UseOutlines Page Count : 16 Access Level : Customer,Guest,Partner Secondary Concept : Cisco IOS 15.2E Content Type : cisco.com#US#postSales Ia Path : cisco.com#Products#Cisco Products#Switches#Industrial Ethernet Switches#Cisco Industrial Ethernet 3010 Series Switches Auto Play : Modify Date : 2017:01:10 08:59:40-08:00 Entitlement Expression : contains( "0,1,2,3,4,7" , $profileField[3] ) Title : Release Notes for the Industrial Ethernet 3010 Switch, Cisco IOS Release 15.2(2)E Doc Type : TSD Products Release Note Secondary Doctype : Document Id : 1455699431337328 Down Loadable : View Able : Producer : Acrobat Elements 10.0.0 (Windows); modified using iText 2.1.7 by 1T3XT Description : Release Notes for the Industrial Ethernet 3010 Switch, Cisco IOS Release 15.2(2)E Fire Wall : Alfresco Doc Version : Creator : FrameMaker 11.0 Country : US Alfresco Trace ID : Concept : Cisco Industrial Ethernet 3010 Series Switches Date : 2017-01-10T08:57:13.026-08:00 Author : ctsadmin-wem-p.gen Create Date : 2013:10:15 04:16:04ZEXIF Metadata provided by EXIF.tools